Directed Electronics 737T Owner`s manual

Directed Electronics 737T Owner`s manual
NEDERLANDS
Owner’s Manual
SVENSKA
DEUTSCH
ITALIANO
ESPAÑOL
FRANÇAIS
Stereo Integrated Amplifier
ENGLISH
C 356BEE
РУССКИЙ
®
IMPORTANT SAFETY INSTRUCTIONS
ENGLISH
SAVE THESE INSTRUCTIONS FOR LATER USE.
FOLLOW ALL WARNINGS AND INSTRUCTIONS MARKED ON THE
AUDIO EQUIPMENT.
FRANÇAIS
ESPAÑOL
ITALIANO
DEUTSCH
NEDERLANDS
SVENSKA
1 Read instructions - All the safety and operating instructions should be
read before the product is operated.
2 Retain instructions - The safety and operating instructions should be
retained for future reference.
3 Heed Warnings - All warnings on the product and in the operating
instructions should be adhered to.
4 Follow Instructions - All operating and use instructions should be
followed.
5 Cleaning - Unplug this product from the wall outlet before cleaning.
Do not use liquid cleaners or aerosol cleaners. Clean only with a dry
cloth.
6 Attachments - Do not use attachments not recommended by the
product manufacturer as they may cause hazards.
7 Water and Moisture - Do not use this product near water-for example,
near a bath tub, wash bowl, kitchen sink, or laundry tub; in a wet
basement; or near a swimming pool; and the like.
8 Accessories - Do not place this product on an unstable cart, stand,
tripod, bracket, or table. The product may fall, causing serious injury to
a child or adult, and serious damage to the product. Use only with a
cart, stand, tripod, bracket, or table recommended by the manufacturer,
or sold with the product. Any mounting of the product should follow
the manufacturer’s instructions, and should use a mounting accessory
recommended by the manufacturer.
9
A product and cart combination should be moved with
care. Quick stops, excessive force, and uneven surfaces may
cause the product and cart combination to overturn.
10 Ventilation - Slots and openings in the cabinet are provided for
ventilation and to ensure reliable operation of the product and to
protect it from overheating, and these openings must not be blocked
or covered. The openings should never be blocked by placing the
product on a bed, sofa, rug, or other similar surface. This product should
not be placed in a built-in installation such as a bookcase or rack unless
proper ventilation is provided or the manufacturer’s instructions have
been adhered to.
11 Power Sources - This product should be operated only from the type of
power source indicated on the marking label. If you are not sure of the
type of power supply to your home, consult your product dealer or local
power company. The primary method of isolating the amplifier from
the mains supply is to disconnect the mains plug. Ensure that the mains
plug remains accessible at all times. Unplug the AC power cord from the
AC outlet if the unit will not be used for several months or more.
12 Grounding or Polarization - This product may be equipped with a
polarized alternating current line plug (a plug having one blade wider
than the other). This plug will fit into the power outlet only one way.
This is a safety feature. If you are unable to insert the plug fully into the
outlet, try reversing the plug. If the plug should still fail to fit, contact
your electrician to replace your obsolete outlet. Do not defeat the safety
purpose of the polarized plug.
13 Power Cord Protection - Power supply cords should be routed so that
they are not likely to be walked on or pinched by items placed upon or
against them, paying particular attention to cords at plugs, convenience
receptacles, and the point where they exit from the product.
РУССКИЙ
2
14 Outdoor Antenna Grounding - If an outside antenna or cable system
is connected to the product, be sure the antenna or cable system is
grounded so as to provide some protection against voltage surges
and built-up static charges. Article 810 of the National Electrical Code,
ANSI/NFPA 70, provides information with regard to proper grounding
of the mast and supporting structure, grounding of the lead-in wire
to an antenna discharge unit, size of grounding conductors, location
of antenna discharge unit, connection to grounding electrodes, and
requirements for the grounding electrode.
NOTE TO CATV SYSTEM INSTALLER
This reminder is provided to call the CATV system installer’s attention to Section
820-40 of the NEC which provides guidelines for proper grounding and, in
particular, specifies that the cable ground shall be connected to the grounding
system of the building, as close to the point of cable entry as practical.
15 Lightning - For added protection for this product during a lightning
storm, or when it is left unattended and unused for long periods of
time, unplug it from the wall outlet and disconnect the antenna or
cable system. This will prevent damage to the product due to lightning
and power line surges.
16 Power Lines - An outside antenna system should not be located in the
vicinity of overhead power lines or other electric light or power circuits,
or where it can fall into such power lines or circuits. When installing an
outside antenna system, extreme care should be taken to keep from
touching such power lines or circuits as contact with them might be
fatal.
17 Overloading - Do not overload wall outlets, extension cords, or
integral convenience receptacles as this can result in a risk of fire or
electric shock.
18 Object and Liquid Entry - Never push objects of any kind into this
product through openings as they may touch dangerous voltage points
or short-out parts that could result in a fire or electric shock. Never spill
liquid of any kind on the product.
WARNING: THE APPARATUS SHOULD NOT BE EXPOSED TO
DRIPPING OR SPLASHING, AND OBJECTS FILLED WITH LIQUIDS,
SUCH AS VASES, SHOULD NOT BE PLACED ON THE APPARATUS.
AS WITH ANY ELECTRONIC PRODUCTS, USE CARE NOT TO SPILL
LIQUIDS INTO ANY PART OF THE SYSTEM. LIQUIDS CAN CAUSE A
FAILURE AND/OR A FIRE HAZARD.
THE LIGHTNING FLASH WITH ARROWHEAD SYMBOL, WITHIN
AN EQUILATERAL TRIANGLE, IS INTENDED TO ALERT THE USER
TO THE PRESENCE OF UNINSULATED “DANGEROUS VOLTAGE”
WITHIN THE PRODUCT’S ENCLOSURE THAT MAYBE OF
SUFFICIENT MAGNITUDE TO CONSTITUTE A RISK OF ELECTRIC
SHOCK TO PERSONS.
CAUTION
Changes or modifications to this equipment not expressly approved by
NAD Electronics for compliance could void the user’s authority to operate
this equipment.
CAUTION REGARDING PLACEMENT
To maintain proper ventilation, be sure to leave a space around the unit
(from the largest outer dimensions including projections) that is equal to or
greater than shown below.
Left and Right Panels: 10 cm
Rear Panel: 10 cm
Top Panel: 10 cm
WARNING
TO REDUCE THE RISK OF FIRE OR ELECTRIC SHOCK, DO NOT EXPOSE THIS
PRODUCT TO RAIN OR MOISTURE.
РУССКИЙ
SVENSKA
NEDERLANDS
CAUTION
TO PREVENT ELECTRIC SHOCK, MATCH WIDE BLADE OF PLUG TO WIDE SLOT,
FULLY INSERT.
ITALIANO
ESPAÑOL
FRANÇAIS
THE EXCLAMATION POINT WITHIN AN EQUILATERAL TRIANGLE IS
INTENDED TO ALERT THE USER TO THE PRESENCE OF IMPORTANT
OPERATING AND MAINTENANCE (SERVICING) INSTRUCTIONS IN
THE LITERATURE ACCOMPANYING THE APPLIANCE.
DEUTSCH
19 Damage Requiring Service - Unplug this product from the wall outlet
and refer servicing to qualified service personnel under the following
conditions:
a) When the power supply cord or plug is damaged.
b) If liquid has been spilled, or objects have fallen into the product.
c) If the product has been exposed to rain or water.
d) If the product does not operate normally by following the operating
instructions. Adjust only those controls that are covered by the
operating instructions as an improper adjustment of other controls
may result in damage and will often require extensive work by a
qualified technician to restore the product to its normal operation.
e) If the product has been dropped or damaged in any way.
f) when the product exhibits a distinct change in performance-this
indicates a need for service.
20 Replacement Parts - When replacement parts are required, be
sure the service technician has used replacement parts specified
by the manufacturer or have the same characteristics as the
original part. Unauthorized substitutions may result in fire, electric
shock, or other hazards.
21 Safety Check - Upon completion of any service or repairs to this
product, ask the service technician to perform safety checks to
determine that the product is in proper operating condition.
22 Wall or Ceiling Mounting - The product should be mounted to a wall
or ceiling only as recommended by the manufacturer.
23 Heat - The product should be situated away from heat sources such as
radiators, heat registers, stoves or other products (including amplifiers)
that produce heat.
24 Headphones - Excessive sound pressure form earphones and
headphones can cause hearing loss.
25 Battery Disposal - When disposing of used batteries, please comply
with governmental regulations or environmental public instruction’s
rules that apply in your country or area. Batteries (battery pack or
batteries installed) must not be exposed to excessive heat such as
sunshine, fire or the like.
ENGLISH
IMPORTANT SAFETY INSTRUCTIONS
3
IMPORTANT SAFETY INSTRUCTIONS
ENGLISH
NOTES ON ENVIRONMENTAL PROTECTION
At the end of its useful life, this product must not be disposed
of with regular household waste but must be returned to a
collection point for the recycling of electrical and electronic
equipment. The symbol on the product, user’s manual and
packaging, point this out.
FRANÇAIS
The materials can be reused in accordance with their markings. Through
re-use, recycling of raw materials or other forms of recycling of old
products, you are making an important contribution to the protection of
our environment. Your local administrative office can advise you of the
responsible waste disposal point.
ESPAÑOL
INFORMATION ABOUT COLLECTION AND DISPOSAL OF
WASTE BATTERIES (DIRECTIVE 2006/66/EC OF THE EUROPEAN
PARLIAMENT AND THE COUNCIL OF EUROPEAN UNION) (FOR
EUROPEAN CUSTOMERS ONLY)
Batteries bearing any of these symbols indicate
that they should be treated as “separate collection”
and not as municipal waste. It is encouraged that
necessary measures are implemented to maximize
the separate collection of waste batteries and
to minimize the disposal of batteries as mixed
municipal waste.
ITALIANO
End-users are exhorted not to dispose waste
batteries as unsorted municipal waste. In order to
achieve a high level of recycling waste batteries, discard waste batteries
separately and properly through an accessible collection point in your
vicinity. For more information about collection and recycling of waste
batteries, please contact your local municipality, your waste disposal service
or the point of sale where you purchased the items.
DEUTSCH
By ensuring compliance and conformance to proper disposal of waste
batteries, potential hazardous effects on human health is prevented and
the negative impact of batteries and waste batteries on the environment
is minimized, thus contributing to the protection, preservation and quality
improvement of the environment.
NEDERLANDS
NOTE: THE C 356BEE IS NOT AN AUTO VOLTAGE UNIT. CONNECT
ONLY TO THE PRESCRIBED AC OUTLET, I.E., 120V 60HZ OR 230V 50HZ.
RECORD YOUR MODEL NUMBER (NOW, WHILE YOU CAN SEE IT)
The model and serial number of your new C 356BEE are located on the
back of the cabinet. For your future convenience, we suggest that you
record these numbers here:
Model no: . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Serial no.: . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
SVENSKA
РУССКИЙ
NAD is a trademark of NAD Electronics International, a division of Lenbrook Industries Limited
Copyright 2010, NAD Electronics International, a division of Lenbrook Industries Limited
4
INTRODUCTION
Packed with your C 356BEE you will find:
• The SR 8 remote control with 2 (two) AA batteries
• This owner’s manual
• A detachable mains power cord
SAVE THE PACKAGING
Please save the box and all of the packaging in which your C 356BEE
arrived. Should you move or otherwise need to transport your C 356BEE,
this is by far the safest container in which to do so. We’ve seen too many
otherwise perfect components damaged in transit for lack of a proper
shipping carton, so please: Save that box!
BARE WIRES AND PIN CONNECTORS
WARNING: The terminals marked with this symbol
are hazardous live. External wiring connected to these
terminals requires installation by an instructed person or
the use of ready-made leads or cords.
Bare wires and pin connectors should be inserted into the hole in the shaft
of the terminal. Unscrew the speaker terminal’s plastic bushing until the
hole in the screw shaft is revealed. Insert the pin or bare cable end into
the hole and secure the cable by tightening down the terminal’s bushing.
Ensure bare wire from the speaker cables does not touch the back panel or
another socket. Ensure that there is only ½ inch (1cm) of bare cable or pin
and no loose strands of speaker wires.
FRANÇAIS
UNPACKING AND SETUP
WHAT’S IN THE BOX
ENGLISH
GETTING STARTED
NOTES ON INSTALLATION
Your C 356BEE should be placed on a firm, level surface. Avoid placing the
unit in direct sunlight or near sources of heat and damp. Allow adequate
ventilation. Do not place the unit on a soft surface like a carpet. Do not
place it in an enclosed position such a bookcase or cabinet that may
impede the airflow through the ventilation slots. Make sure the unit is
switched off before making any connections.
ITALIANO
Please make all the connections to your C 356BEE with the unit unplugged
from the mains power source. It is also advisable to power down or unplug
all associated components while making or breaking any signal or AC
power connections.
1 Connect your speakers to the LEFT and RIGHT speaker terminals and
input sources to the applicable rear panel input sockets.
2 Connect the mains power cord to the C 356BEE’s AC Mains input and
then plug into a mains power source.
3 Set the rear panel POWER switch to the “ON” setting. The Standby LED
indicator embedded around the bezel of the STANDBY button will
illuminate amber and the C 356BEE goes to standby mode.
4 Press the front panel STANDBY button to turn ON the C 356BEE. The
Standby LED indicator will turn from amber to blue.
5 Select preferred active Source input by pressing the corresponding
front panel input selector button.
DEUTSCH
It is especially important that sufficient ventilation be provided. If you are
contemplating locating the C 356BEE within a cabinet or other furniture,
consult your NAD audio/video specialist for advice on providing adequate
airflow.
In case you simply cannot wait to experience the performance of your new
C 356BEE, we provide the following “QUICK START” instructions to get you
underway.
ESPAÑOL
QUICK START
CHOOSING A LOCATION
Choose a location that is well ventilated (with at least several inches to
both sides and behind), and that will provide a clear line of sight, within
23 feet/7 meters, between the C 356BEE’s front panel and your primary
listening/viewing position. This will ensure reliable infrared remote control
communications. The C 356BEE generates a modest amount of heat, but
nothing that should trouble adjacent components. It is perfectly possible to
stack the C 356BEE atop other components, but the reverse usually should
be avoided.
NEDERLANDS
The RCA sockets on your C 356BEE are colour coded for convenience. Red
and white are Right and Left audio respectively. Use high quality leads and
sockets for optimum performance and reliability. Ensure that leads and
sockets are not damaged in any way and all sockets are firmly pushed home.
For best performance, use quality speaker leads of 16 gauge (1.5mm2)
thickness or more. Switch off the POWER switch if you intend not to use the
C 356BEE for long periods of time (such as when on vacation).
SVENSKA
Should water get into your C 356BEE, shut off the power to the unit and
disconnect the plug from the mains power source. Have the unit inspected
by a qualified service technician before attempting to use it again.
DO NOT REMOVE THE COVER; THERE ARE NO USER-SERVICEABLE
PARTS INSIDE.
РУССКИЙ
Use a dry soft cloth to clean the unit. Do not use solutions containing
benzol or other volatile agents.
5
IDENTIFICATION OF CONTROLS
FRONT PANEL
ENGLISH
1
2
3
4
5
6
FRANÇAIS
ESPAÑOL
7
8
ITALIANO
1 STANDBY BUTTON: With the rear panel POWER switch set to ON
position, press this button to switch ON the C 356BEE from standby
mode. The Standby LED indicator will turn from amber to blue. Pressing
the STANDBY button again turns the unit back to standby mode.
The C 356BEE can also be switched ON from standby mode by pressing
any of the front panel buttons.
2 STANDBY LED: This indicator will light up amber when the C 356BEE
is at standby mode. When the C 356BEE is powered up from standby
mode, this indicator will illuminate blue. When infrared command from
the SR 8 is received, this indicator will also flash momentarily.
DEUTSCH
In cases of serious abuse of the C 356BEE, such as excessively low
loudspeaker impedance and short circuit, the C 356BEE will engage its
Protection circuitry, indicated by the Standby LED turning from blue to
red and the sound being muted.
NEDERLANDS
In such a case, turn OFF the C 356BEE via the rear panel POWER switch.
Wait for it to cool down and/or check the speaker connections. Once
the cause for the protection circuitry to engage has been removed, set
the rear panel POWER switch to the “ON” setting. Then press the front
panel STANDBY button to resume normal operation.
SVENSKA
3 PHONES: A 1/4” stereo jack socket is supplied for headphone listening
and will work with conventional headphones of any impedance. The
headphone socket will work in parallel with the selected speakers. To
listen to headphones only, de-select SPEAKERS A and/or B. The volume,
tone and balance controls are operative for headphone listening. Use
a suitable adapter to connect headphones with other types of sockets,
such as 3.5mm “personal stereo” jack plugs.
NOTE
Make certain that the volume control is turned to minimum (fully
counterclockwise) before connecting or disconnecting headphones.
Listening at high levels can damage your hearing.
РУССКИЙ
4 SOFT CLIPPING INDICATOR: This indicator is illuminated blue if the
rear panel SOFT CLIPPING switch is set to ON position. Refer also to the
item below about SOFT CLIPPING at the IDENTIFICATION OF CONTROLS
– REAR PANEL.
6
9
10
11
12
5 MP SOCKET: Using a 3.5mm stereo plug, connect into this socket the
audio output of a Media Player.
NOTES
• If an external Media Player is connected to the front MP socket (using a
3.5mm stereo plug) while listening to a MP line-level source, the external
Media Player will be directly selected with the MP line-level source
immediately disconnected.
• It is recommended to mute the volume or switch to a different input
before plugging/unplugging the external Media Player cable.
6 REMOTE SENSOR: Point the SR 8 remote control at the remote
sensor and press the buttons. Do not expose the remote sensor of the
C 356BEE to a strong light source such as direct sunlight or illumination.
If you do so, you may not be able to operate the C 356BEE with the
remote control.
Distance: About 23ft (7m) from the front of the remote sensor.
Angle: About 30° in each direction of the front of the remote sensor.
7 SPEAKERS A, B: The SPEAKERS A and B buttons engage or disengage
the speakers connected respectively to the SPEAKERS A and SPEAKERS
B terminals on the rear panel. Press “A” to switch ON or OFF the speakers
connected to the SPEAKERS A terminals. Press “B” to switch ON or OFF
the speakers connected to the SPEAKERS B terminals. Press both “A” and
“B” to engage at the same time both SPEAKERS A and SPEAKERS B. The
corresponding blue LED indicator embedded around the SPEAKERS A
and SPEAKERS B buttons will illuminate accordingly when each or both
are engaged.
IDENTIFICATION OF CONTROLS
If an external Media Player is connected to the front MP socket (using
a 3.5mm stereo plug) while listening to a MP line-level source, the
external Media Player will be directly selected with the MP line-level
source immediately disconnected. It is recommended to mute the
volume or switch to a different input before plugging/unplugging the
external Media Player cable.
FRANÇAIS
MP (MEDIA PLAYER): Selects a line-level source connected to the MP
sockets as the active input.
11 BALANCE: The BALANCE control adjusts the relative levels of the
left and right speakers. The 12 o’clock position provides equal level to
the left and right channels. A detent indicates this position. Rotating
the control clockwise moves the balance towards the right. Rotating
the control counterclockwise moves the balance to the left. The
BALANCE control does not affect recordings made using the TAPE
output terminals but will affect the signal going to the Pre-amp output
terminals (PRE OUT 1 and PRE OUT 2).
12 VOLUME: The VOLUME control adjusts the overall loudness of the
signals being fed to the loudspeakers or headphones. Turn clockwise
to increase the volume level; counter clockwise to lower it. The
VOLUME control does not affect recordings made using the TAPE
output terminals but will affect the signal going to the Pre-amp output
terminals (PRE OUT 1 and PRE OUT 2).
ESPAÑOL
8 INPUT SELECTORS: These buttons select the active input to the
C 356BEE and the signal sent to the loudspeakers, headphones and the
PRE OUT sockets. The corresponding buttons on the remote control
handset duplicate these buttons. When selected, the corresponding
input LED indicator embedded around the bezel of the particular input
button will illuminate blue.
ENGLISH
FRONT PANEL
CD: Selects the CD player (or other line-level source) connected to the
CD sockets as the active input.
TUNER: Selects the tuner (or other line-level source) connected to the
tuner sockets as the active input.
ITALIANO
DISC/MDC: Selects a line-level source connected to the DISC sockets.
If an optional Modular Design Construction (MDC) module is installed,
the DISC input socket is disabled and the MDC source is selected as the
active input.
AUX: Selects a line-level source connected to the AUX sockets as the
active input.
DEUTSCH
TAPE 2: Selects TAPE 2 as the active input.
TAPE MONITOR: Selects the output from a tape recorder when playing
back tapes or monitor recordings that are being made through the
TAPE MONITOR sockets.
NEDERLANDS
TAPE MONITOR does not override the current input selection. For
example, if CD is the active input when TAPE MONITOR is selected, then
the CD signal will continue to be selected and sent to both the TAPE 2
and TAPE MONITOR output sockets, but it is the sound from recorder
connected to TAPE MONITOR that will be heard in the loudspeakers.
Apart from the TAPE MONITOR LED illuminated to indicate it is engaged,
the corresponding LED indicator for the active input will also stay
illuminated.
SVENSKA
9 TONE DEFEAT: Tone Controls are enabled or disabled by pressing this
button. When enabled (TONE DEFEAT LED indicator is illuminated), the
Tone Control circuits are bypassed. The Tone Control circuits are active
when the TONE DEFEAT LED indicator stays extinguished.
РУССКИЙ
10 TONE CONTROLS: The C 356BEE is fitted with BASS and TREBLE tone
controls to adjust the tonal balance of your system. The 12 o’clock
position is “flat” with no boost or cut, and an indent indicates this
position. Rotate the control clockwise to increase the amount of Bass or
Treble. Rotate the control counterclockwise to decrease the amount of
Bass or Treble. The Tone controls do not affect recordings made using
the TAPE output terminals but will affect the signal going to the Preamp output terminals (PRE OUT 1 and PRE OUT 2).
7
IDENTIFICATION OF CONTROLS
REAR PANEL
ENGLISH
19
FRANÇAIS
ESPAÑOL
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
120V Version
Model Only
ITALIANO
ATTENTION!
Please make sure that the C 356BEE is powered off or unplugged from the mains power source before making any connections. It is also advisable to power
down or unplug all associated components while making or breaking any signal or AC power connections.
1 RS-232: Connect this interface using RS-232 serial cable (not
supplied) to any Windows® compatible PC to allow remote control of
the C 356BEE via compatible external controllers. NAD is a certified
partner of AMX and Crestron and fully supports these external devices.
Check out the NAD website for information about AMX and Crestron
compatibility with NAD. See your NAD audio specialist for more
information.
4 MP INPUT: Input for a Media Player or other line-level signal source.
Use a twin RCA-to-RCA lead to connect these sockets to the left and
right analog output of a Media Player.
DEUTSCH
NOTE
If an external Media Player is connected to the front MP socket (using a
3.5mm stereo plug) while listening to a MP line-level source, the external
Media Player will be directly selected with the MP line-level source
immediately disconnected.
NEDERLANDS
2 12V TRIGGER OUT: The +12V TRIGGER OUT is used for controlling
external equipment that is equipped with a +12V trigger input. This
output will be 12V when the C 356BEE is ON and 0V when the unit is
either OFF or in standby. This output can drive a load up to 150mA at
12V.
5 CD INPUT: Input for a CD player or other line-level signal source. Use
a twin RCA-to-RCA lead to connect these sockets to the left and right
analog output of a CD player.
3 IR IN/OUT: These mini-jacks accept and output remote-controlled
codes in electrical format, using industry-standard protocols, for use
with “IR-repeater” and multi-room systems and related technologies.
6 TUNER INPUT: Input for a tuner or other line-level signal source. Use
a twin RCA-to-RCA lead to connect these sockets to the left and right
analog output of a tuner.
IR IN: This input is connected to the output of an IR (infrared) repeater
(Xantech or similar) or the IR output of another component to allow
control of the C 356BEE from a remote location.
SVENSKA
IR OUT: When connected to the IR IN of an ancillary equipment, direct
the ancillary equipment’s own remote control to the C 356BEE’s infrared
receiver to command or control the linked unit.
All NAD products with IR IN/IR OUT features are fully compatible with
the C 356BEE. For non-NAD models, please check with your other
product’s service specialists with respect to its compatibility with the
C 356BEE’s IR features.
РУССКИЙ
8
7 DISC INPUT: Input for additional line level input signals such as CD,
Mini Disc player or the output signal from a step-up amplifier for a
turntable. Use a twin RCA-to-RCA lead to connect these sockets to the
left and right analog output of the auxiliary device.
NOTE
If an optional Modular Design Construction (MDC) module is installed,
the DISC input socket is disabled and the MDC source is selected as the
active input.
8 AUX INPUT: Input for additional line level input signals such as another
CD player. Use a twin RCA-to-RCA lead to connect these sockets to the
left and right analog output of the auxiliary device.
IDENTIFICATION OF CONTROLS
11 PRE OUT 1: The PRE OUT 1 sockets can be used to drive an additional
power amplifier. Use a twin RCA-to-RCA lead to connect the left and
right “Audio Input” of the Power amplifier or processor to the PRE OUT 1
sockets.
Always turn the C 356BEE and associated external power amplifiers OFF
before connecting or disconnecting anything to the PRE OUT 1 sockets.
The PRE OUT 1 output signal will be affected by the C 356BEE’s volume
and tone control settings.
12 PRE OUT 2: Connections to an external power amplifier or processor,
such as a surround-sound decoder. In normal use, this should be
connected to the MAIN IN sockets with the links supplied. To connect
your C 356BEE to an external processor or amplifier, remove first these
links. Use a twin RCA-to-RCA lead to connect the left and right “Audio
Input” of a power amplifier or processor to the PRE OUT 2 sockets.
Always turn the C 356BEE and associated external power amplifiers OFF
before connecting or disconnecting anything to the PRE OUT 2 sockets.
The PRE OUT 2 output signal will be affected by the C 356BEE’s volume
and tone control settings.
13 MAIN IN: Connections to an external preamplifier or processor, such as
a surround sound decoder. In normal use, this should be connected to
PRE OUT 2 sockets with the links supplied. To connect your C 356BEE to
an external processor or preamplifier, remove first these links. Use a twin
RCA-to-RCA lead to connect the left and right “Audio Output” of the
preamplifier or processor to the MAIN IN sockets.
Always turn the C 356BEE and associated external preamplifiers OFF
before connecting or disconnecting anything to the MAIN IN sockets.
FRANÇAIS
ESPAÑOL
ITALIANO
NOTE
There will be no TAPE 2 output when TAPE 2 is the selected source input.
This prevents feedback through the recording component thereby
preventing possible damage to your speakers. The same applies to TAPE
MONITOR IN/OUT.
15 SPEAKERS A, B: The C 356BEE is equipped with two sets of speaker
connectors. Use the SPEAKERS A terminals for the “main” speakers and
use the SPEAKERS B terminals for a second pair, for example, extension
speakers located in another room.
Connect the right speaker to the terminals marked “R +” and “R-”
ensuring that the “R+” is connected to the “+” terminal on your
loudspeaker and the “R-” is connected to the loudspeaker’s “-” terminal.
Connect the terminals marked “L+” and “L-” to the left speaker in the
same way.
DEUTSCH
TAPE TO TAPE COPYING
You can copy between two tape recorders connected to your C 356BEE.
Put the source tape in the recorder connected to TAPE 2 and the blank
tape into the recorder connected to TAPE MONITOR. By selecting TAPE 2
input you can now record from TAPE 2 to TAPE MONITOR and monitor
the signal coming from the original tape.
POWERDRIVE
The C 356BEE uses NAD’s proprietary PowerDrive™ amplifier technology
that provides high dynamic power and low impedance drive capability.
By adding a second high-voltage rail to our well regulated highcurrent power supply, we get an “overdrive” that can nearly double the
continuous power on a short term dynamic power basis. This uniquely
efficient power supply topology provides the real world benefits of
high dynamic power that remains uncompromised by low impedance
speakers.
Always use heavy duty (16 gauge; 1.5mm2 or thicker) stranded wire to
connect loudspeakers to your C 356BEE. The high-current binding post
terminals can be used as a screw terminal for cables terminating in
spade or pin sockets or for cables with bare wire ends.
16 SWITCHED AC OUTLET (120V version only): This convenience outlet
can supply switched power to another component or accessory. With
the POWER switch at the rear panel set to ON position, this outlet is
powered ON or OFF by the front panel STANDBY switch or by the SR 8’s
[ON/OFF] buttons. The total draw of all devices connected to this outlet
must not exceed 120 watts.
17 AC MAINS INPUT: The C 356BEE comes supplied with a separate
detachable mains power cord. Before connecting the plug to the mains
power source, ensure that it is firmly connected to the C 356BEE’s AC
Mains input socket first. Connect only to the prescribed AC outlet,
i.e., 120V 60 Hz (for 120V version models of C 356BEE only) or 230V
50 Hz (for 230V version models of C 356BEE only). Always disconnect
the mains power plug from the mains power source first, before
disconnecting the cable from the C 356BEE’s AC Mains input socket.
18 POWER SWITCH: The POWER switch supplies the master mains power
for the C 356BEE. When this switch is at ON position, the C 356BEE
is in standby mode as shown by the amber status condition of the
standby LED. Toggle the front panel’s STANDBY button to switch ON the
C 356BEE or back to standby mode. Switch off the POWER switch if you
intend not to use the C 356BEE for long periods of time (such as when
on vacation). It is not possible to switch ON the C 356BEE using the
front panel STANDBY button or SR 8 remote control’s [ON] button if the
rear panel POWER switch is switched off.
9
NEDERLANDS
TO MAKE A RECORDING
When any source is selected, its signal is also fed directly to any tape
recorder connected to the TAPE 2 OUT or TAPE MONITOR OUT for
recording.
The SOFT CLIPPING indicator on the front panel will illuminate when the
C 356BEE is in Soft Clipping mode. Refer also to the item below about
“POWERDRIVE”.
SVENSKA
10 TAPE MONITOR IN/OUT: Connections for analog recording and
playback to a secondary tape recorder of any type. Using twin
RCA-to-RCA leads, connect the left and right “Audio Output” of the
tape recorder to the TAPE MONITOR IN sockets for playback and
tape monitoring. Connect the left and right “Audio Input” of the tape
recorder to the TAPE MONITOR OUT sockets for recording.
14 SOFT CLIPPING™: Enables NAD’s proprietary Soft Clipping circuitry
on all channels. At [ON] position, Soft Clipping gently limits the output
of the C 356BEE to minimize audible distortion should the amplifier be
over driven. Soft Clipping may simply be left ON at all times to reduce
the likelihood of audible distortion from excessive volume settings.
However, for critical listening and to preserve optimum dynamics, you
may wish to defeat it by setting this switch to “OFF” position.
РУССКИЙ
9 TAPE 2 IN/OUT: Connections for analog recording and playback to
a tape recorder of any type. Using twin RCA-to-RCA leads, connect
the left and right “Audio Output” of the tape recorder to the TAPE 2 IN
sockets for playback. Connect the left and right “Audio Input” of the tape
recorder to the TAPE 2 OUT sockets for recording.
ENGLISH
REAR PANEL
IDENTIFICATION OF CONTROLS
REAR PANEL
ENGLISH
19 MDC CLASSIC UPGRADE SLOT: Remove cover to install the
optional Modular Design Construction (MDC) module. An example
of a C 356BEE-compatible MDC Classic module is the PP 375 Phono
Preamplifier module. The PP 375 is integrated into the chassis of the
C 356BEE, automatically assigned to the DISC input and its level well
matched to the other sets of line level input.
FRANÇAIS
A
Consult with your NAD dealer on how to procure the PP 375 and
its consequent installation to the C 356BEE. Check out also the NAD
website for any announcement about future release(s) of other
C 356BEE-compatible MDC Classic modules.
With the optional PP 375 installed, refer below for descriptions of key
PP 375 parts.
B
C
D
ESPAÑOL
ITALIANO
A MC INPUT: Input for a Moving Coil phono cartridge. Connect the twin
RCA lead from your turntable to this input if you are using a Moving Coil
cartridge.
DEUTSCH
B MC-MM SWITCH: Slide this switch to either MM (Moving Magnet) or
MC (Moving Coil) depending upon the Phono cartridge being used.
NEDERLANDS
SVENSKA
РУССКИЙ
10
C PHONO GROUND CONNECTOR: Turntables normally includes a single
wire earth lead. Use the C 356BEE Phono ground connector to connect
this lead. Unscrew the terminal to expose the hole, which will accept
the lead. After insertion, tighten the terminal to secure the lead.
D MM INPUT: Input for a Moving Magnet Phono cartridge. Connect
the twin RCA lead from your turntable to this input if you are using a
Moving Magnet cartridge.
IDENTIFICATION OF CONTROLS
When a command from the remote control is received, the Standby LED indicator will blink. Note that
the indicator may also blink when receiving commands not necessarily for the C 356BEE but for other
components in the system. Please refer to previous sections of the manual for a full description of
individual functions.
10
1 POWER ON, OFF: The SR 8 remote has a separate ON and OFF button. With the rear panel POWER
switch set to ON position, press the ON button to switch the C 356BEE from Standby mode to
operating mode. Press the OFF button to switch the unit to Standby mode.
2 DEVICE SELECTOR: A Device Selector button determines only what component the SR 8 will
command; it does not perform any function on the C 356BEE. Press desired Device Selector button
for the applicable buttons to be directed to a “page” of commands relevant to the selected device.
Upon selecting a Device, you can now press the corresponding SR 8 control buttons applicable for
the selected Device.
3 INPUT SELECTORS: Refer to the corresponding labels printed in the remote control faceplate
and their respective assigned buttons to make use of these functions. Set the DEVICE SELECTOR
to “AMP” in order to gain access to these buttons. The input selector buttons perform the same
functions as the buttons labeled the same on the front panel.
DEUTSCH
9
NOTE
The remote control handset supplied with the C 356BEE is of universal type designed to operate
several NAD models. Some buttons are applicable only to specific NAD models. Contact your dealer
or NAD audio specialist for assistance.
4 NUMERIC KEYS: The numeric keys allow for direct input of tracks for CD players, and direct
channel/preset access for tuners and receivers.
5 SLEEP: Switch off the NAD Receiver or Tuner after a preset number of minutes.
6 MUTE: Press the [MUTE] button to temporarily switch OFF the sound to the speakers and
headphones. MUTE mode is indicated by the Standby LED indicator flashing for NAD Integrated
Amplifiers or “Mute” shown in the VFD of NAD Receivers. Mute does not affect recordings made
using the TAPE output terminals but will affect the signal going to the PRE OUT terminals. Press
[MUTE] again to restore sound.
7 DIM (for use with compatible NAD Stereo Receiver, Tuner and CD Player): Reduce, turn off
or restore VFD brightness. Depending on the NAD model, the brightness of the front panel display
will vary when you toggle this button.
8 VOL
: Press [VOL
] button to increase or decrease the loudness level. Release the
button when the desired level is reached. For NAD Receivers, the VFD will also show “Volume Up”
or “Volume Down” while pressing SR 8’s [VOL
] buttons. The VOLUME buttons do not affect
recordings made using the TAPE output terminals but will affect the signal going to the PRE OUT
terminals.
NEDERLANDS
8
SVENSKA
7
9 SPK A, SPK B: The [SPK A] and [SPK B] buttons engage or disengage the speakers connected
respectively to the SPEAKERS A and SPEAKERS B terminals. Toggle [SPK A] to switch ON or OFF the
speakers connected to the SPEAKERS A terminals. Toggle [SPK B] to switch ON or OFF the speakers
connected to the SPEAKERS B terminals. Press both buttons to engage both speakers.
10 TONE DFT: Tone Controls are enabled or disabled by pressing this button.
11
РУССКИЙ
6
FRANÇAIS
5
3, 4
ESPAÑOL
2
1
ITALIANO
USING THE SR 8 REMOTE CONTROL
The SR 8 remote control handset handles the key functions of the C 356BEE as well as other NAD
Stereo Receivers, Integrated Amplifiers and Preamplifiers. It has additional controls to remotely operate
NAD CD Players, AM/FM Tuners and dedicated AM/FM/DB Tuners. It will operate up to a distance of
23ft (7m). Alkaline batteries are recommended for maximum operating life. Two AA batteries should
be fitted in the battery compartment at the rear of the Remote Control handset. When replacing
batteries, check that they have been put in the right way round, as indicated on the base of the battery
compartment.
ENGLISH
SR 8 REMOTE CONTROL
IDENTIFICATION OF CONTROLS
SR 8 REMOTE CONTROL
ENGLISH
FRANÇAIS
CD PLAYER CONTROL (for use with compatible NAD CD Player): Set the DEVICE SELECTOR
to “CD” in order to gain access to these buttons. Some of the control buttons below are applicable
only to specific NAD CD Player models; check the owner’s manual of your NAD CD Player for control
button compatibility. You can also load the applicable NAD code library to this device so that it can be
made compatible with your other NAD equipment. Refer to the section below about “USING THE SR 8
REMOTE CONTROL LIBRARY” on how to load a NAD code library.
SCAN [
]: Fast reverse/forward search.
[ ] : Open or close disc tray.
[ ] : Stop playback.
[ ] : Pause playback temporarily.
[
] : Go to next track/file.
] : Go to beginning of current track/file or to previous track/file.
[
[ ]: Start playback.
[
]: Select through folder list/Select through WMA/MP3 files.
ENTER: Select desired folder or WMA/MP3 file.
DISP: Show playback time and other display information.
RAND: Play tracks/files in random order.
RPT: Repeat track, file or whole disc.
PROG: Enter or exit program mode.
CLEAR: Delete track or file number from the program list.
CD: Select CD as the active source.
USB: Select USB as the active source.
OPT: Select optical input as the active source.
SRC: Select desired SRC mode.
ESPAÑOL
ITALIANO
DEUTSCH
TUNER CONTROL (for use with compatible NAD Receiver, AM/FM/DB Tuner): Set the DEVICE
SELECTOR to “TUN” in order to gain access to these buttons. Refer to the corresponding labels printed
in the remote control faceplate and their respective assigned buttons to make use of these functions.
Some of the control buttons below are applicable only to specific NAD Receiver or Tuner models;
check the owner’s manual of your NAD Receiver or Tuner for control button compatibility. You can also
load the applicable NAD code library to this device so that it can be made compatible with your other
NAD equipment. Refer to the section below about “USING THE SR 8 REMOTE CONTROL LIBRARY” on
how to load a NAD code library.
AUTO TUNE: Automatically scan all available local DAB broadcasts.
TUNE [
] or [
]: Tune forward or backwards.
] or [
]: Step up or down Preset numbers.
PRESET [
AM/FM/DB: Select XM, DAB, FM or AM band as applicable.
TUNER MODE: Activate “FM Mute On” or “FM Mute Off” at FM mode. In combination with [
],
select through applicable XM or DAB menu options.
BLEND: Engage or disengage BLEND feature.
MEMORY: Save current station into a preset number.
DELETE: Delete selected preset number or all preset numbers.
[
]: In combination with TUNER MODE or other compatible buttons, select through applicable
XM or DAB menu options.
ENTER: Select Preset or Tune mode at AM/FM band. Display signal strength at DAB mode.
INFO: Show display information as supplied by the currently tuned RDS station, XM channel or
DAB broadcast.
NEDERLANDS
SVENSKA
РУССКИЙ
12
IDENTIFICATION OF CONTROLS
ENGLISH
SR 8 REMOTE CONTROL
USING THE SR 8 REMOTE CONTROL LIBRARY
The SR 8 can store a different library of default NAD codes for each of its
DEVICE SELECTOR “pages.” If the original default library does not control
your NAD CD player, DVD player, or other component, follow the procedure
below to change the library code. Refer as well to the table below for a list
applicable NAD Library Codes with their corresponding NAD models.
ESPAÑOL
FRANÇAIS
LOAD ANOTHER LIBRARY CODE
Example: Load NAD DVD Player T 517 library code to SR 8’s “CD” device.
1 Press and hold [CD] in the DEVICE SELECTOR section of SR 8.
2 While holding down the device button (CD), press “2” and “2” using
SR 8’s numeric buttons. “22” is the corresponding library code for T 517.
3 Press [ENTER] while still holding down the device button (CD). The
CD device selector will flash once to indicate that the library input is
successful. Both the device selector button (CD) and [ENTER] can now
be released.
ITALIANO
RESET THE SR 8 TO ITS DEFAULT SETTINGS
The SR 8 can be restored to its factory settings, including default libraries, by
the following procedures
1 Press and hold [ON] and [DELETE/CLEAR] buttons for about 10 seconds
until the AMP device button lights up.
2 Within two seconds of the AMP device button lighting up, release both
buttons. If the reset mode is successful, the [CD] device button will flash
twice.
NAD PRODUCT DESCRIPTION
10
Default library for “AMP” page
11
Zone 2
20
Default library for “CD” page; C 515BEE, C 545BEE, C 565BEE
21
T 535, T 585, M55, DVD section of L 54, VISO TWO, VISO FIVE
22
T 513, T 514, T 515, T 517
23
T 587, T 557, T 577, M56
30
IPD 1
31
IPD 2
40
Default library for “TUN” page; Tuner section of C 725BEE, T 175,
T 737, T 747, T 755, T 765, T 775, T 785
41
C 422, C 425
42
C 445
NEDERLANDS
LIBRARY CODE
DEUTSCH
TABLE OF LIBRARY CODES APPLICABLE TO SR 8 REMOTE CONTROL
РУССКИЙ
SVENSKA
NOTE
The SR 8 may not necessarily contain all the control buttons applicable
for the above-mentioned NAD products. Use the prescribed remote
control of the specific NAD product for a full compliment of the
applicable remote control buttons.
13
REFERENCE
TROUBLESHOOTING
ENGLISH
CONDITION
No sound.
POSSIBLE CAUSES
POSSIBLE SOLUTIONS
FRANÇAIS
ESPAÑOL
ITALIANO
• Mains power cord unplugged or power not
switched ON.
• Check if mains power cord is plugged in and
power switched ON.
• TAPE MONITOR selected.
• De-select TAPE MONITOR mode.
• Mute on.
• Switch off Mute.
• Rear PRE OUT/MAIN IN amp links not fitted.
• Fit links.
• Balance control not centered.
• Center Balance control.
• Speaker not properly connected or damaged.
• Check connections and speakers.
• Input lead disconnected or damaged.
• Check leads and connections.
No audio despite the presence of an active
input at DISC rear panel input terminals.
• DISC input is disabled due to an installed
MDC module at the MDC Classic Upgrade
slot.
• Uninstall the MDC module from the MDC
Classic Upgrade slot.
No audio despite the presence of an active
input at MP rear panel input terminals.
• An external Media Player is connected to the
front MP socket.
• Unplug the Media Player connected to the
front MP socket.
Weak bass/diffused stereo image.
• Speakers wired out of phase.
• Check connections to all speakers in the
system.
C 356BEE does not respond to remote
control commands.
• Battery flat or incorrectly inserted.
• Check or replace battery. Follow correct
battery insertion setup.
• Infrared receiver (IR) window of the C 356BEE
or IR transmitter of the remote control is
obstructed.
• Check IR windows and ensure clear line-ofsight from remote control to C 356BEE.
• IR receiver in direct sun or very bright
ambient light.
• Place unit away from direct sun, reduce
amount of ambient light.
• C 356BEE has overheated.
• Shut down C 356BEE by turning off the rear
panel POWER switch. Ensure that there is
adequate space below, above and to the
sides of the C 356BEE to allow proper air flow.
After C 356BEE has cooled down, turn back
ON. Restart again the C 356BEE by switching
ON the rear panel POWER switch and then
pressing the front panel STANDBY button or
remote control’s [ON] button.
• Overall impedance of loudspeakers too low.
• Ensure the overall loudspeaker impedance is
not below 4 ohms.
No sound one channel.
Standby LED turns red during operation.
DEUTSCH
NEDERLANDS
SVENSKA
РУССКИЙ
14
REFERENCE
ENGLISH
SPECIFICATIONS
PREAMPLIFIER SECTION
Maximum voltage output -IHF load
600 ohms load
TONE CONTROLS
Treble
Bass
FRANÇAIS
Channel separation -1 kHz
10 kHz
Input impedance (R and C)
Maximum input signal
Output impedance - Pre out
Tape out
Input sensitivity
Frequency response
<0.005 % at 2 V out
>106 dB (IHF; A-weighted, ref. 500 mV out, unity gain)
>114 dB (A-weighted, ref. 2 V out, Volume maximum)
>92 dB (ref. 100 mV out, unity gain)
>80 dB
>68 dB
22 kohms+ 100 pF
>6 Vrms (ref. 0.1 % THD)
80 ohms
Source Z + 1 kohm
166 mV (ref. 500 mV out)
±0.3 dB (20 Hz - 20 kHz, Tone defeat ON)
±0.3 dB (20 Hz - 20 kHz, Tone defeat OFF)
>10 V (ref. 0.03 % THD)
>8 V (ref. 0.03 % THD)
ESPAÑOL
LINE LEVEL INPUT, PRE OUT
THD1 20 Hz – 20 kHz, CCIF IMD, SMPTE IMD, DIM 100
Signal-to-Noise Ratio
±5 dB at 10 kHz
±8 dB at 100 Hz
POWER AMPLIFER SECTION
Input impedance
Input sensitivity
Voltage gain
Headphone output impedance
Channel separation - 1 kHz
10 kHz
ITALIANO
DEUTSCH
Damping factor
Frequency response
>80 W (at rated THD, 20 Hz-20 kHz, both channels driven)
<0.007 %
>90 W (at 1 kHz 0.1 % THD)
+2.6 dB
+4.4 dB
145 W
220 W
290 W
>50 A (in 1 ohm, 1 ms)
>101 dB (A-weighted, ref. 1 W)
>120 dB (A-weighted, ref. 80 W)
>100 (at 8 ohms, 50 Hz and 1 kHz)
±0.3 dB (ref. 20 Hz - 20 kHz)
3 Hz – 70 kHz (ref. -3 dB)
20 kohms + 1 nF
950 mV (for 80 W in 8 ohms)
29 dB
220 ohms
>80 dB
>70 dB
NEDERLANDS
MAIN IN, SPEAKER OUT
Continuous output power into 8 ohms and 4 ohms (Stereo)
Rated THD1 20 Hz – 20 kHz, CCIF IMD, SMPTE IMD, DIM 100
Clipping power
IHF dynamic headroom - 8 ohms
4 ohms
IHF dynamic power - 8 ohms
4 ohms
2 ohms
Peak output current
Signal-to-noise ratio
TRIGGER OUT
SVENSKA
75 ohms
150 mA
+12 V ± 10 %
РУССКИЙ
Output resistance
Output current
Output voltage
15
REFERENCE
SPECIFICATIONS
ENGLISH
PHONO SECTION (WITH OPTIONAL PP 375 INSTALLED)
MM/MC IN, PRE OUT
Input impedance - MC
MM
FRANÇAIS
Input sensitivity2 for 80 W in 8 ohms - MC
MM
Input sensitivity2 for 1 W in 8 ohms - MC
MM
Input overload - MC
MM
Gain - MC in - TAPE OUT3
MM in - TAPE OUT
THD1 (CCIF IMD, DIM 100)
Signal-to-Noise Ratio, IHF A-weighted - MC4
MM5
RIAA response accuracy
ESPAÑOL
Infrasonic filter
Channel Separation - MC
MM
100 ohms (R)
180 pF (C)
47 kohms (R)
180 pF (C)
0.38 mV 1 kHz
5.0 mV 1 kHz
39 uV 1 kHz
0.56 mV 1 kHz
0.6 mV/5.9 mV/58 mV (20 Hz/1 kHz/20 kHz)
9.3 mV/85 mV/850 mV (20 Hz/1 kHz/20 kHz)
57.0 dB (at 1 kHz, 10 kohms load)
34.2 dB (at 1 kHz, 10 kohms load)
<0.009 % (20 Hz – 20 kHz, 4 Vrms TAPE OUT)
>78 dB (ref. 0.5 mV input, 10 ohms source)
>75 dB (ref. 5 mV input, IHF cartridge source)
±0.5 dB (20 Hz – 50 Hz)
±0.3 dB (50 Hz – 20 kHz)
-3 dB at 10 Hz
-14 dB at 4 Hz
>60 dB (1 kHz and 10 kHz)
>60 dB (1 kHz and 10 kHz)
ITALIANO
OVERALL SPECIFICATIONS
LINE LEVEL INPUT, SPEAKER OUT
Continuous output power into 8 ohms and 4 ohms (Stereo)
THD1 20 Hz – 20 kHz, CCIF IMD, SMPTE IMD, DIM 100
Signal-to-Noise Ratio
Frequency response
DEUTSCH
Channel separation - 1 kHz
10 kHz
>80 W (at rated THD, 20 Hz-20 kHz, both channels driven)
<0.009 % (250 mW to 80 W, 8 ohms and 4 ohms)
>92 dB (IHF; A-weighted, 500 mV input, ref. 1 W out in 8 ohms)
>110 dB (IHF; A-weighted, ref. 80 W in 8 ohms, maximum volume)
±0.3 dB (20 Hz - 20 kHz, Tone Defeat ON)
10 Hz – 65 kHz (-3 dB)
>80 dB
>68 dB
POWER CONSUMPTION
Rated power
Standby power
Idle power
350 W (at 230 V AC 50 Hz; 120V AC 60 Hz)
<0.5 W
<40 W
NEDERLANDS
DIMENSION AND WEIGHT
Unit Dimensions (W x H x D) Gross6
Net weight
Shipping weight
435 x 131 x 337 mm
17 1/8 x 5 3/16 x 13 5/16 inches
8.7 kg (19.2 lbs)
10.6 kg (23.4 lbs)
SVENSKA
LEGEND:
1 THD is the sum of all the harmonic components within the 80 kHz measurement bandwidth and does not include noise.
2 Measured from Speaker Out.
3 Measured with 10 ohms generator impedance.
4 Measured with 10 ohms input termination.
5 Measured with MM cartridge connected (600 mH + 600 ohms).
6 Gross dimensions include feet, volume knob and tightened speaker terminals.
Specifications are subject to change without notice. For updated documentation and features, please log onto www.NADelectronics.com for the latest
information about C 356BEE.
РУССКИЙ
16
www.NADelectronics.com
©2010 NAD ELECTRONICS INTERNATIONAL
A DIVISION OF LENBROOK INDUSTRIES LIMITED
All rights reserved. NAD and the NAD logo are trademarks of NAD Electronics International, a division of Lenbrook Industries Limited.
No part of this publication may be reproduced, stored or transmitted in any form without the written permission of NAD Electronics International.
C 356BEE Owner’s Manual Issue 1.9-07/10
C 356BEE DAC Integrated Amplifier
Our C 356BEE DAC with the new MDC DAC built in, symbolises NAD’s desire for continual improvement—even on an
award-winning design. We have refined our amplifier performance and added more value to our C 356BEE DAC design by
applying knowledge gained from our top-of-the-line Masters Series M3 Amplifier. Able to drive the most complex loud
speakers to their full musical potential, the C 356BEE DAC can challenge amplifiers costing two to three times more. With
features like Preamp Out, Modular Design Construction, and the MDC DAC’s ability to play computer music, this amp will
suit your requirements for years to come.
2 x 80W
Features
> Purely Digital
With our C 356BEE DAC, the world of computer music can
be heard through your hi-fi system without the noise or
distortion that commonly plagues analogue designs. Thanks
to an ‘asynchronous USB’ technique and its high precision
clock, 24/96 quality computer music flows smoothly without
‘jitter’ or harsh distortion. You can also plug Apple TV into
the C 356BEE DAC to hear iTunes like never before!
> Modular Design Construction (MDC)
The C 356BEE DAC, equipped with our MDC DAC Digital
Analogue Converter, allows computer music to be streamed
from your computer or networked storage device without
musical compromise. MDC makes future upgrades possible
with interchangeable modules!
> Legendary Technology
Our NAD PowerDrive circuit delivers very high dynamic power
and low impedance drive to accurately control loudspeakers,
resulting in musically detailed, coherent, and relaxed sound.
PowerDrive™ offers the capability of an amplifier twice as
powerful without the energy drainage. Our exclusive Soft
Clipping feature protects speakers (and ears) from damaging
clipping distortion.
> Real World Power
With 80W of continuous power (both channels), our
C 356BEE DAC has the lowest levels of distortion and noise
available in its price class. We use the most demanding
criterion for performance measurement—Full Disclosure
Power—measuring distortion under the most extreme
conditions of low impedance loads and frequency extremes,
rather than the easy 1kHz @ 8 ohms test used by many of
our competitors.
> Greener NAD
The C 356BEE DAC offers <0.5W standby consumption and
includes a convenient ‘vacation’ switch. We make every effort
to reduce our environmental impact by manufacturing the
C 356BEE DAC without heavy metals and other hazardous
substances, and by using recycled and recyclable materials
where possible.
©NAD C 356BEE DAC
Total Width 435mm
Total Depth 337mm
Total Height
130.86mm
Specifications
LINE IN, SPEAKER OUT
C 356BEE DAC
Continuous output power into 8 Ω and 4 Ω (Stereo)
>80W (at rated THD, 20Hz-20kHz, both channels driven)
THD* 20Hz - 20kHz, CCIF IMD, SMPTE IMD, DIM 100 <0.009% (250mW to 80W, 8 Ω and 4 Ω)
Clipping Power
>90W (at 1kHz 0.1% THD)
IHF Dynamic Headroom
8 Ohms +2.6dB
4 Ohms +4.4dB
IHF Dynamic Power
8 Ohms 145W
4 Ohms 220W
2 Ohms 290W
Signal/Noise Ratio
>92dB (IHF; A-weighted, 500mV input, ref. 1W out in 8 Ω) >110dB (IHF; A-weighted, ref. 80W in 8 Ω, max. volume)
Frequency Response ±0.3dB (20Hz-20kHz, Tone Defeat ON)
10Hz - 65kHz (-3dB)
Channel Separation
1kHz >80dB
10kHz >68dB
MDC DAC Module
Sample Rate
32kHz to 96kHz
THD+N
0.005%
Signal/Noise
-90dB (ref. 500mV Tape out)
Output Level
2V (at Tape out)
Inputs
Digital Optical USB 2.0 (Device side Asynchronous)
Digital to Analogue Converter
Burr-Brown TI PCM1796
POWER CONSUMPTION
Standby Power
Idle Power
Rated Power
DIMENSION AND WEIGHT
Unit Dimensions (W x H x D) Gross**
Net Weight
Shipping Weight
<0.5W
<40W
350W (230V AC 50Hz; 120V AC 60Hz)
435 x 130.86 x 337mm
17 1/8 x 5 3/16 x 13 5/16 inches***
9.8kg (19.6lbs***)
12.4kg (23.8lbs***)
* THD is the sum of all the harmonic components within the 80kHz measurement bandwidth and does not include noise.
** Gross dimensions include feet, buttons and rear panel terminals.
*** Non-metric measurements are approximate. NAD Electronics will not assume any liability for errors being made by retailers, custom
installers, cabinet makers, or other end users based on information contained in this document.
Note: Installers should allow a minimum clearance of 55mm for wire/cable management.
NAD Electronics International reserves the right to change specifications or features without notice. NAD is a registered trademark of NAD Electronics
International. All rights reserved. No part of this publication may be reproduced, stored, or transmitted in any form whatsoever without the written
permission of NAD Electronics International. © 07/11 11-059 NAD Electronics International.
www.NADelectronics.com
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertisement