BARON SERIES - sinclair air conditioners

BARON SERIES - sinclair air conditioners
USER'S MANUAL
BARON SERIES
ASH-09AB, ASH-12AB
CONTENTS
Operation and maintenance
■
■
■
■
■
■
............................................................1
Notices for use ....................................................................3
Specificate Model and Technical Data .....................................5
Names and functions of each part ..........................................7
Operation of wireless remote control ........................................8
Clean and care .................................................................12
Notices for operation
■ Troubleshooting ................................................................14
Installation service
■ Notices for installation ........................................................17
■
■
■
■
Installation dimension diagram ..............................................19
Install indoor unit ...............................................................20
............................................................22
Check after installation and test operation ..............................23
■ Installation and Maintenance of Healthy Filter ..........................24
■ Configuration of connection pipe and additional volume of refrigerant ....25
Install outdoor unit
This symbol stands for the items
should be forbidden.
This symbol stands for the items
should be followed
The products in this manual may be different with the real one, according to different
models, some models have displayer and some models without displayer, the position
and shape of the displayer please refer to the real one.
This appliance is not intended for use by persons (including children) with reduced
physical, sensory or mental capabilities or lack of experience and knowledge,
unless they have been given supervision or instruction concerning use of the appliance
by a person responsible for their safety.
Children should be supervised to ensure that they do not play with the appliance.
Do not dispose this product as unsorted municipal waste.
Collection of such waste separately for special treatment
is necessary.
Operation and maintenance-notices for operation
★ Earth: The ground be
connected!
★
Be sure to pull out the power plug
★ Select the most appropriate temperature.
when not using the air conditioner
for a long time.
Keep room cooler than outside
about 5 degree.
If not, please ask the qualified personnel to install. Furthermore, don't connect each wire to the gas pipe, water
pipe, drainage pipe or any other improper places.
Otherwise, the accumulated dust
may cause fire or electric shock.
★ Don't leave windows and
★ Don't block the air intake or outlet
It can decrease the air conditioning
capacity.
It can decrease the air conditioning
capacity or cause a malfunction.
doors open for a long time
while operating the air conditioner.
★ Please note whether the installed
stand is firm enough or not.
If it is damaged, it may lead to
the fall of the unit and cause
the injury.
vents of both the outdoor and indoor
units.
★
Don't step on the top of the
outdoor unit or place something
on it.
As falling off the outdoor unit
can be dangerous.
1
It can preclude the electricity wasted.
★ Keep combustible spray away
from the units more than 1m.
It can cause afire or explosion.
★
Don't attempt to repair
the air conditioner by yourself.
The wrong repair will lead to
an electric shock or fire, so
you should contact the service
center to repair.
Notices for operation
★ If the supply cord is damaged, it must be replaced
★ The airflow direction can be adjusted appro-
priately. At operating, adjust the vertical airflow
direction by adjusting the louvers of upward/downward direction. And then, hold two ends of
left and right louver to adjust the horizontal airflow.
by the manufacturer or its service agent or a
similarly qualified person in order to avoid a
hazard.
Louver of left/right direction
★ Don't insert your hands or stick into the air
intake or outlet vents.
Louver of upward/
downward direction.
★ Don't blow the wind to animals and plants
directly. It can cause a bad influence to them.
Otherwise it will cause accident.
★ Don't apply the cold wind to the body for a
long time.
★ Don't use the air conditioner for other purposes,
such as drying clothes, preserving foods, etc.
It can cause the health problems.
★ Splashing water on the air conditioner can
cause an electric shock and malfunction.
★ Don't place a space heater near the air
conditioner.
Or CO toxicosis may occur for imcomplete
burning.
2
Notices for use
Working principle and special functions for cooling
Principle:
Air conditioner absorbs heat in the room and transmit to outdoor and discharged, so that
indoor ambient temperature decreased, its cooling capacity will increase or decrease by
outdoor ambient temperature.
Anti-freezing function:
If the unit is running in COOL mode and in low temperature, there will be frost formed on
the heat exchanger, when indoor heat exchanger temperature decreased below 0℃ , the
indoor unit microcomputer will stop compressor running and protect the unit.
Working principle and special functions for heating
Principle:
* Air conditioner absorbs heat from outdoor and transmits to indoor, in this way to increase
*
room temperature. This is the heat pump heating principle, its heating capacity will be
reduced due to outdoor temperature decrease.
If outdoor temperature becomes very low, please operate with other heating equipments.
Defrosting:
* When outdoor temperature is low but high humidity, after a long while running, frost will
*
*
*
form on outdoor unit, that will effect the heating effect, at this time, the auto defrosting
function will act, the heat running will stop for 8-10mins.
During the auto defrosting, the fan motors of indoor unit and outdoor unit will stop.
During the defrosting, the indoor indicator flashes, the outdoor unit may emit vapor.
This is due to the defrosting, it isn't malfunction.
After defrosting finished,the heating will recover automatically.
Anti-cool wind function:
In "Heat" mode, under the following three kinds of state, if indoor heat exchanger doesn't
arrive at certain temp., indoor fan will not act, in order to prevent cool wind blowing(within
2 mins):
1. Heating starts.
2. After Auto Defrost finished.
3. Heating under the low temperature.
3
Notices for use
Gentle Breeze
In the following situation, the indoor unit may blow gentle breeze, and
the guide louver rotate to a certain position:
1. In “Heat” mode, the unit turned on, the compressor doesn’t arrive the starting condition.
2. In “Heat” mode, the temperature arrive at the setting value and the compressor stop
running about 1min.
Working temperature range
Indoor sideDB/WB(oC)
Outdoor sideDB/WB(oC)
Maximum cooling
32/23
43/26
Maximum heating
27/---
24/18
The operating temperature range (outdoor temperature) for cooling only unit is 18℃~ 43℃;
for heat pump unit is -7℃~ 43℃.
4
Names and functions of each part
Indoor unit
Air in
⑴
⑶
⑷
⑹
Air out
⑸
The pattern in displayer:
⑺
⑵
:Cool
:Dry
⑴ Power cable
Wireless
remote control
:Heat
⑵ Remote control
:Run
⑶ Front panel
:Set temp.
⑷ Filter
⑸ Guide louver
⑹ Wall pipe
Outdoor unit
⑺ Bind tape
Air in
⑻ Connection wire
⑼ Drainage pipe
⑻
⑼
Air out
7
Operation of wireless remote control
Names and functions of wireless remote control
Note: Be sure that there are no obstructions between receiver and remote controller;
Don't drop or throw the remote control; Don't let any liquid in the remote control and
put the remote control directly under the sunlight or any place where is very hot.
Signal transmitter
SLEEP
SLEEP button
●
Remote control
FAN
Press this button, Sleep On and Sleep
Off can be selected. After powered on,Sleep
Off is defaulted. After the unit is turned
off, the Sleep function is canceled. After
Sleep function set up, the signal of Sleep
will display. In this mode, the time of timer
can be adjusted. Under Fan and Auto
modes, this function is not available.
FAN button
● By pressing this key, you may select AUTO,
ON/OFF
FAN 1, FAN 2, FAN 3 or FAN 4, and may
also cycle between them. FAN 4 only in
cool or heat mode. After being energized,
AUTO is defaulted. Only LOW fan can be
set under DRY mode, pressing this key
can not adjust the fan speed, but can
send message.
ON/OFF button
● Press
this button, the unit will be turned on,
press it once more, the unit will be turned
off. When turning on or turning off the unit,
the Timer, Sleep function will be canceled,
but the presetting time is still remained.
MODE
AUTO
MODE button
SWING
Press this button, Auto, Cool,Dry, Fan,
Heat mode can be selected circularly.
Auto mode is default while power on.
Under Auto mode,the temperature will not
modes, the initial value is 25℃( 77 oF).
AUTO
COOL
HEAT
DRY
FAN
FAN
▲ ▲
AUTO
DRY
COOL
HEAT
(Only for cooling and heating unit.
As for cooling only unit, it won’t
have any action when it receives
the signal of heating operation.)
8
Fan 2
Fan 3
Fan 4
SWING button
●
be displayed; Under Heat mode, the
initial value is 28℃( 82 oF);Under other
▲ ▲ ▲
●
Fan 1
Press this key to activate or deactivate
the swing.
Operation of wireless remote control
Names and functions of wireless remote control
Notice: This is a general use remote controller, it could be used for the air conditioners
with multifunction; For some function, which the model dosen't have, if press the
corresponding button on the remote controller that the unit will keep the original
running status.
TIMER
TIMER button
● By pressing this key under switch-off state,
you may set the time for auto switch-on. The
range of setting is 0.5 ~ 24 hours. The
characters "T-ON" and "H" will flash for 5
seconds. Within 5 seconds,you may make
one press of this key to complete the setting
and send the message.If the setting is valid,
the set time will be displayed for 2 seconds
before display of the temperature message.
During flash, you may press "+" key to
increase the value and press "-" key to decrease
Remote control
the value. The time will increase or decrease
by 0.5 hours with each press of this key.
If pressing "+" or "-" key continuously, the
time value will change rapidly. The remote
controller can increase the set time by 0.5
hours every 0.25 seconds. After being
energized, the fault is no timer setting, and
+
there is no display of "T-ON" or "H". Press
+ button
ON/OFF key to switch on the unit and cancel
the auto switch-on.When the temperature
● For presetting temperature increasing.
Press this button,can set up the temperature,
when unit is on . Continuously press and
hold this button for more than 2 seconds,
the corresponding contents will be
changed rapidly, until unpress the button
then send the information, ℃(℉)is displaying all along. In Auto mode, the temperature can not be set up, but operate this
button can send the signal. Centigrade
setting range :16-30; Fahrenheit scale
setting range 61-86.
-
display becomes constant, you may press
this key again to display the remaining set
time. The time value, "T-On" and "H" will
display constantly for 2 seconds. After 2
seconds,the preset temperature will be
displayed. Within these 2 seconds, you may
press this key again to cancel the auto
switch-on and send the message.
● By pressing this key under switch-on state,
you may set the time for auto switch-off.
The method of setting as the same as for
auto switch-on.
- button
● Presetting temperature can be decreased.
Press this button, the temperature can be
set up, continuously press this button
and hold for two seconds, the relative
contents can quickly change, until unhold
this button and send the order that the ℃
(oF) signal will be displayed all the time.
The temperature adjustment is unavailable under the Auto mode, but the order
can be sent by if pressing this button.
9
Operation of wireless remote control
Guide for operation- General operation
1. After powered on, press ON/OFF button, the unit will start to run.(Note: When
it is powered on, the guide louver of main unit will close automatically.)
2. Press MODE button, select desired running mode.
3. Pressing + or - button, to set the desired temperature. (It is unnecessary
to set the temp. at AUTO mode.)
4. Pressing FAN button, set fan speed, can select AUTO, FAN 1, FAN 2,
FAN 3 or FAN 4.
5. Pressing SWING button, to select the swing.
Guide for operation- Optional operation
1. Press SLEEP button, to set sleep.
2. Press TIMER button, can set the scheduled timer on or timer off.
Introduction for special function
★ About AUTO RUN
When AUTO RUN mode is selected, the setting temperature will not be displayed on the
LCD, the unit will be in accordance with the room temp. automatically to select the suitable
running method and to make ambient comfortable.
★ About
LOCK
Under switch-on or switch-off state, you may hold "+" and "-" key simultaneously to lock and
unlock the keypad. When locked, the display will show the LOCK icon, in which case the
lock icon will flash three times upon operation of any key. After the keypad is unlocked, the
lock icon on the display will be hidden. After being energized, the default is unlock.
★ About switch between Fahrenheit and Centigrade
Under switch-off state, you may hold "-" and "MODE" keys simultaneously to switch between
℃ and ℉ .
★ About
Lamp
Under switch-on or switch-off state, you may hold "+" and "FAN" key simultaneously for 3 seconds
to set the lamp on or off and send the code. After being energized, the lamp is defaulted on.
★ About
Blow over heat
When the unit is running in Heat mode or Auto Heat mode, compressor and indoor fan is running,
to turn the unit off, the compressor, outdoor fan will stop running. The upper and lower guide board
rotate to horizontal position, then the indoor fan will run at low fan speed, 10s later, the unit will turn
off.
10
Operation of wireless remote control
Changing batteries and notices
1. Slightly to press the place
to take out the back cover of wireless
remote control.(As shown in figure)
2. Take out the old batteries. (As show in figure)
3. Insert two new AAA1.5V dry batteries, and pay attention to the polarity.
(As show in figure)
4.
Attach the back cover of wireless remote control. (As show in figure)
Fig.1
★ NOTE:
● When changing the batteries, do not use the old or different batteries,
otherwise, it can cause the malfunction of the wireless remote control.
●
●
●
●
If the wireless remote control will not be used for a long time, please
take them out, and don't let the leakage liquid damage the wireless
remote control.
The operation should be in its receiving range.
It should be placed at where is 1m away from the TV set or stereo sound sets.
If the wireless remote control can not operate normally, please take them out,
after 30s later and reinsert, if they cannot normally run, please change them.
Fig.2
Emergency operation
●
●
If the wireless remote control is lostor broken,
please use the manual switch button. At this time,
the unit will run at the Auto mode, but the temperature
and fan speed cannot be changed. The operation
was shown as below:
To open the panel, the manual switch is on the
displayer box.
Turn on the unit: At unit turned off, press the button,
the unit will run at Auto mode immediately.The
microcomputer will accord to the indoor temperature
to select (Cooling, Heating, Fan) and obtain the
comfortable effect.
Turn off the unit: At unit turned on, press the button,
the unit will stop working.
11
Manual switch
Fig.3
Clean and care
Caution
●
●
Disconnect the power supply before cleaning air conditioner, or it may cause electric shock.
Never sprinkle water on the indoor unit and the outdoor unit for cleaning because it can cause an
electric shock.
●
Volatile liquid (e.g. thinner or gasoline) will damage the air conditioner. (So wipe the units with a
dry soft cloth, or a cloth slightly moistened with water or cleanser.)
Clean the front panel
When cleaning the front panel, please dip the cloth into the water temperature of 45℃ below, then to dry
the cloth and wipe the dirty part.
Note: Please do not to immerse the front panel in water, due to there are microcomputer components and
circuit diagrams on the front panel.
Clean the air filter (Recommended once every three months)
NOTE: If dust is much more around the air conditioner, the air filters should be cleaned many times.
After taking off the filter, don't touch the fin of indoor unit, in order to avoid hurt your fingers.
① Take down the air filter
At the slot of surface panel to open an angle, pull the air filter
downward and take it out, please see the Fig. 4(a, b).
(a)
(b)
② Clean the air filter
To clean the dust adhering to the filters, you can either
use a vacuum cleaner, or wash them with warm water
the water with the neutral detergent should below 45
degree) ,and dry it in the shade.
NOTE: Never use water above 45℃ to clean, or it can
cause deformation or discoloration. Never parch it by
fire, or can cause a fire or deformation.
③ Insert the air filter
Reinsert the filters along the direction of arrowhead, and
then to cover the cover and clasp it.
12
Fig.4
Clean and care
Check before use
①
Be sure that nothing obstructs the air outlet and intake vents.
②
Check that whether ground wire is properly connected or not.
③
Check that whether the batteries of air conditioner are
changed or not.
④
Check that whether the installation stand of the outdoor
unit is damaged or not. If damaged, please contact the dealer.
Maintain after use
①
Turn main power off.
②
Clean the filter and indoor and outdoor units' bodies.
③
Clear dust and obstructions from the outdoor unit.
④
Repaint the rubiginous place on the outdoor unit to prevent it from spreading.
⑤
Adopt the special shield to cover the outdoor unit, avoid the rain water, dust enter into
the unit and get rust.
13
Troubleshooting
CAUTION
Don't attempt to repair the air conditioner by yourself, it can cause an electric shock or
fire. Please check the following items before asking for repair, it can save your time and
money.
Phenomenon
Troubleshooting
Not operate immediately when the air
conditioner is restarted.
Once the air conditioner is stopped, it will
not operate in approximately 3 minutes to
protect itself.
●
Waiting
There's unusual smell blowing from the outlet
after operation is started.
● The
unit has no peculiar smell by itself. If has,
that is due to the smell accumulated in the
ambient.
● Solution
method: Cleaning the filter.
If problem still has, so need to clean air
conditioner. (Please contact with the authorized
maintenance center.)
Sound of water flow can be heard during
the operation.
In COOL mode, sometimes the mist emitted
from the air outlet vent.
Creaking noise can be heard when start or
stop the unit.
●
The air conditioner is started, when it is
running the compressor started or stopped
running, or the unit is stopped, sometimes
there is swoosh or gurgle, the sound is due
to refrigerant flowing they are not malfunctions.
●
When the indoor temperature and humidity
are very high, this phenomenon would
happen. This is caused by the room air is
swiftly cooled down. After running for a while,
indoor temperature and humidity will fall
down, the mist will die away.
●
This is caused by the deformation of plastic
due to the changes of temperature.
14
Troubleshooting
Phenomenon
Troubleshooting
● Has the power been shut down?
The unit can not run.
● Is power plug loosed?
● Is the circuit protection device tripped off or not?
● Is voltage higher or lower?
(Tested by professionals)
Breaking off
Cooling(Heating) efficiency is not good.
● Is the TIMER correctly used?
● Is Temp. setting suitable?
● Were inlet and outlet vents obstructed?
● Is filter dirty?
● Are the windows and doors clothed?
● Did Fan speed set at low speed?
● Is there any heat sources in the room?
Wireless remote control is not available.
● The unit is interfered by abnormal or frequent
functions switchover occasionally the controller
cannot operate. At this time, you need to pull out
of the plug, and reinsert it.
● Is it in its receiving range? Or obstructed?
To check the voltage in wireless remote control inside
is charged, otherwise to replace the batteries.
● Whether the wireless remote control is damaged.
If water leakage in the room.
● The air humidity is on the high side.
● Condensing water over flowed.
● The connection position of indoor unit drainage
pipe is loosed.
If water leakage in outdoor unit.
● When the unit is running in COOL mode, the pipe
and connection of pipe would be condensed due
to the water cooled down.
● When the unit is running in Auto Defrosting mode
the ice thawed and flowed out.
● When the unit is running in HEAT mode, the water
adhered on heat exchanger dripped off.
Noise from indoor unit emitted.
● The sound of fan or compressor relay is switching
on or off.
● When the defrosting is started or stop running,
it will sound. That is due to the refrigerant flowed
to the reverse direction.
15
Troubleshooting
Phenomenon
Indoor unit cannot deliver air .
Troubleshooting
● In HEAT mode, when the temperature of indoor
heat exchanger is very low, that will stop deliver
air in order to prevent cool air. (Within 2min)
● In HEAT mode, when the outdoor temperature
is low or high humidity, there are much frost be
formed on the outdoor heat exchanger, that the
unit will automatically defrost, indoor unit stop
blowing air for 3-12min.
During the defrosting, there is water flowing out
or vapor be produced.
● In dehumidifying mode, sometimes indoor fan will
stop, in order to avoid condensing water be vaporized again, restrain temperature rising.
Moisture on air outlet vent.
●
If unit is running under the high humidity for
a long time, the moisture will be condensed
on the air outlet grill and drip off.
H1: Defrosting
●
It is normal.
Immediately stop all operations and plug out, contact
the dealer in following situations.
There is harsh sound during operation.
The terrible odors emitted during operation.
Water is leaking in the room.
Air switch or protection switch often breaks.
Carelessy splash water or something into unit.
There is an abnormal heat in power supply cord
and power plug.
16
Stop running and disconnect the
power supply.
Notices for installation
Important Notices
1. The unit installation work must be done by qualified personnel according to the local
rules and this manual.
2. Before installation, please contact with local authorized maintenance center, if unit is
not installed by the authorized maintenance center, the malfunction may not solved,
due to discommodious contacts.
3. When removing the unit to the other place, please firstly contact with the authorized
Maintenance Center in the local area.
Basic Requirements For Installation Position
Install in the following place may cause malfunction. If it is unavoidable contact with
service center please:
● Place where strong heat sources, vapors, flammable gas or volatile object are emitted.
● Place where high-frequency waves are generated by radio equipment, welders and
medical equipment.
● Place where a lot of salinities such as coast exists.
● Place where the oil (machine oil) is contained in the air.
● Place where a sulfured gas such as the hot spring zones is generated.
● Other place with special circumstance.
Indoor Unit Installation Position Selection
1. The air inlet and outlet vent should be far from the obstruction, make sure that the air
can be blown through the whole room.
2. Select a position where the condensing water can be easily drained out, and the place
is easily connected for outdoor unit .
3. Select a location where the children can not reach .
4. Can select the place where is strong enough to withstand the fu ll weight and vibration of
the unit. And will not increase the noise .
5. Be sure to leave enough space to allow access for routine maintenance. The height of the
installed location should be 250cm or more from the floor.
6. Select a place about 1m or more away from TVset or any other electric appliances.
7. Select a place where the filter can be easily taken out.
8. Make sure that the indoor unit installation should accord with installation dimension
diagram requirements.
9. Do not use the unit in the immediate surrou ndings of a laundry a bath a shower or a
swimming pool.
Outdoor Unit Installation Position Selection
1. Select a location from which noise and outflow air emitted by unit will not inconvenience
neighbors, animals, plants.
2. Select a location where there should be sufficient ventilation.
3. Select a location where there should be no obstructions cover the inlet and outlet vent.
4. The location should be able to withstand the full weight and vibration of the outdoor unit
and permit safe installation.
5. Select a dry place, but do not expose under the direct sunlight or strong wind.
6. Make sure that the outdoor unit installation dimension should accord with installation
dimension diagram, convenient for maintenance, repair.
7. The height difference of connecting the tubing within 5m, the length of connecting the
tubing within 10m.
8. Select a place where it is out of reach for the children.
9. Select a place where will not block the passage and do not influence the city appearance.
17
Notices for installation
Safety Requirements For Electric Appliances
1. The power supply should be used the rated voltage and AC exclusive circuit, the power
cable diameter should be satisfied.
2. Don't drag the power cable emphatically.
3. It should be reliably earthed, and it should be connected to the special earth device,
the installation work should be operated by the professional.
4. The min. distance from the unit and combustive surface is 1.5m.
5. The appliance shall be installed in accordance with national wiring regulations.
6. An all-pole disconnection switch having a contact separation of at least 3mm in all poles
should be connected in fixed wiring. For models with a power plug, make sure the plug
is within reach after installation.
7. Including an air switch with suitable capacity, please note the following table. Air switch
should be included magnet buckle and heating buckle function, it can protect the
circuit-short and overload. (Caution: please do not use the fuse only for protect the circuit)
Air-conditioner
Note:
Air switch capacity
07、09K
10A
12K
16A
18K、24K
25A
●
Make sure that the Live wire or Zero line as well as the earth wire in the family power
socket can not be wrong connected, there should be reliable and no short circuit in the
diagram.
●
wrong connection may cause fire.
●
GWH18ND-K3NNA2A, GWH18ND-K3NNA4A, GWH18ND-K3NNA8A,
GWH18ND-K3NNB3A, GWH18ND-K3NNB4A can be connected only to a supply with
system impedance no more than 0.232 ohm. In case necessary, please consult your
supply authority for system impedance information.”
Earthing requirements
1. Air conditioner is type I electric appliance, thus please do conduct reliable earthing
measure.
2. The yellow-green two-color wire in air conditioner is earthing wire and cannot be used
for other propose. It cannot be cut off and be fix it by screw, otherwise it would cause
electric shock.
3. The earth resistance should accord to the National Criterion.
4. The user power must offer the reliable earthing terminal. Please don't connect the
earthing wire with the following place:
① Tap water pipe. ② Gas pipe.
③ Contamination pipe.
④ Other places that professional personnel consider them unreliable.
5. The model and rating values for fuses according the silk print on fuse cover or related
PCB board.
18
Installation dimension diagram
Installation dimension diagram
Space to the ceiling
Above
Space to the wall
Above
Above
Space to the wall
Above
Air outlet side
Space to the floor
The dimensions of the space necessary for correct
installation of the appliance including the minimum
permissible distances to adjacent structures
Space to the obstruction
Above
●
Above
Air inlet side
e
ov
Ab
Above
Space to the wall
Space to the wall
Above
ve
o
Ab
Air outlet side
19
Install indoor unit
Install the rear panel
1.Always mount the rear panel horizontally. Due to the water tray of indoor unit has been adopted the
both-way drainage design, the outlet of water tray should be adjusted slightly down when installing, that is
taking the outlet of the water tray as the center of a circle, the included angle between the evaporator and
level should be 0 or more, that is good for condensing water drainage.
Wall
2.Fix the rear panel on the wall with screws. Wall
Mark on the middle of it
Gradienter
Space
Space
(Where is pre-covered with plastic granula)
to the
wall
150m m
above
3.Be sure that the rear panel has been fixed
firmly enough to withstand the weight of an
adult of 60kg, further more, the weight should
be evenly shared by each screw.
to the
wall
150m m
above
Right
Left
Ф55mm
Ф55mm
Fig.5
(Rear piping hole)
(Rear piping hole)
Install the piping hole
Indoor
1.Make the piping hole (Ф55) in the wall at a slight downward slant to the
outdoor side.
Wall pipe
Outdoor
Seal pad
2.Insert the piping-hole sleeve into the hole to prevent the connection piping
and wiring from being damaged when passing through the hole.
Ф55
Install the water drainage pipe
1.For well draining, the drain hose should be placed at a downward slant.
Wrenched
Bent
2.Do not wrench or bend the drain hose or flood its end by water.
3.When the long drainage hose passing through indoor,
should wrap the insulation materials.
Flooded
Connect indoor and outdoor electric wires
1.Open the surface panel.
2.Remove the wiring cover Fig.6.
3.Route the power connection cord and signal control wire (for cooling and heating unit only) from the
back of the indoor unit and pull it toward the front through the wiring hole for connection.
4.Connect the interconnection cord to the terminal block, and then fix the cord with cord anchorge.
5.Reassemble the clampand wiring cover.
6.Recover the surface panel.
05、07、09、12K、14K Cool only type
18K、24K Cool only type
yellowgreen
yellowgreen
Fig.6
05、07、09、12K
Cool and Heat type
violet
18K Cool and Heat type and
GWH09NA-K3NNB3B
24K Cool and Heat type
GWH09NB-K3NNE2A
yellow- yellowgreen green
violet
20
yellowgreen
(red)
brown violet
Install indoor unit
NOTE:
When connecting the electric wire if the wire length is not enough, please contact with
the authorized service shop to buy a exclusive electric wire that is long enough and the
joint on the wire are not allowed.
●
●
●
The electric wiring must be correctly connected, wrong connection may cause spare parts
malfunction.
Tighten the terminal screw in order to prevent loose.
After tighten the screw, slight pull the wire and confirm whether is it firm or not.
●
If the earth wire is wrong connection, that may cause electric shock.
●
The cover plate must be fixed, and tighten the connection wire, if it is poor installed, that
the dust, moisture may enter in or the connection terminal will be affected by outside force,
and will cause fire or electric shock.
Install the indoor unit
The piping can be lead out from right, right rear, left
left rear.
1. When routing the piping and wiring from the left
or right side of indoor unit, cut off the tailings
from the chassis in necessary(Show in Fig.7)
(1) Cut off the tailings 1 when routing the wiring only;
(2) Cut off the tailings 1 and tailings 2 when routing
both the wiring and piping.
2. Take out the piping from body case, wrap the piping
electric wire, water pipe with tape and pull them
through the piping hole (As show in Fig.8)
3. Hange the mounting slots of the indoor unit on the
upper tabs of the rear panel and check if it is firm
enough.(As show in Fig.9)
4. The height of the installed location should be 2.5m
or more from the floor.
Gas side pipe
●
Fig.7
External connection
electric wire
Liquid side piping
Tailing 2
side piping
Tailing 1 Gas
insulation
Liquid side
Piping insulation
Finally wrap it
Water drainage pipe
with tape
Left
Left rear
Right
Right rear
Fixing hook
Mounting
plate
Fig.8
Mounting
baord
Fig.9
Install the connection pipe
1. Align the center of the piping flare with the relevant valve.
2. Screw in the flare nut by hand and then tighten the
nut with spanner and torque wrench refer to the
following:
Hex nut diameter
Ф6
Ф 9.52
Ф 12
Ф 16
Ф 19
Tightening torque(N·m)
15~20
31~35
50~55
60~65
70~75
Indoor unit piping
Spanner
Taper nut Piping
Torque
wrench
NOTE: Firstly connect the connection pipe to indoor unit, then to outdoor unit; pay attention
to the piping bending, do not damage the connection pipe; the joint nut couldn't tighten too
much, otherwise it may cause leakage.
21
Install outdoor unit
Electric wiring
1. Disassemble the handle on the outdoor unit right side plate.
2. Take off cord anchorage. Connect and fix power connect
cord (for cool and heat type,connect and fix power
connect cord and signal control wire)to terminal block.
Handle
3. Fix the power connection cable with cord anchorage,
(for cool and heat type,use the cord anchorage)
to fix the power connection cable and the signal
control wire).
4. Ensure wire has been fixed well.
05、07 、09 、 12K
Cool and Heat type:
05、 07 、 09 、 12K、
14K、24K Cool only type:
N(1)
2
black
blue (brown)
N(1) 2
4
5
blue black violet orange
yellow-green
yellowgreen
Indoor unit
connection
Indoor unit
connection
18K Cool and Heat type:
N(1) 2
4
5
blue black violet orange
5. Install the handle.
NOTE:
● Wrong wiring may cause spare parts malfunction.
● After the cable fixed, make sure there should be
a free space between the connection and
connection and fixing place on the lead wire.
18K Cool only type:
N(1) 2
yellowgreen
Indoor unit
connection
3
24K Cool and Heat type:
blue black
N(1) 2
yellow-green
3
4
5
blue black brown violet orange
Indoor unit
connection
yellowgreen
Indoor unit
connection
Air purging and leakage test
1. Connect charging hose of manifold valve to charge end of low pressure
valve (both high/low pressure valves must be tightly shut).
2. Connect joint of charging hose to vacuum pump.
Manifold
Valve
3. Fully open handle handle of Lo manifold valve.
Multimeter
4. Open the vacuum pump to evacuate. At the beginning, slightly
-76cmHg
loosen joint nut of low pressure valve to check if there
Lo Handle
is air coming inside. (If noise of vacuum pump has
Charging hose
been changed, the reading of multimeter is 0) Then
tighten the nut.
5. Keep evacuating for more than 15mins and make
sure the reading of multi-meter is -1.0 105pa
(-76cmHg)..
6. Fully open high/low pressure valves.
7. Remove charging hose from charging end of low pressure valve.
8. Tighten bonnet of low-pressure valve. (As shown in Fig.10)
Manometer
Hi handle
Charging hose
Vacuum pump
Low pressure valve
Fig.10
Condensate drainage of outdoor unit (no for cooling only)
The condensate and defrosting water formd during heating
in the outdoor unit can be properly discharged by drainage
pipe .
Installation method:set the drain connection in Ø 25 hole of the
chassis has been installed and then connect drainage pipe
with drain nozzle,so that condensate and defrosting waer can
be properly discharged
22
Chassis
Drain
connection
Check after installation and test operation
Check after installation
Items to be checked
Possible malfunction
Has it been fixed firmly?
The unit may drop, shake or emit noise.
Have you done the refrigerant leakage test?
It may cause insufficient cooling(heating)
capacity
Is heat insulation sufficient?
It may cause condensation and dripping.
Is water drainage well?
It may cause condensation and dripping.
Is the voltage in accordance with the rated
voltage marked on the nameplate?
Is the electric wiring and piping
connection installed correctly and securely?
Has the unit been connected to a secure
earth connection?
It may cause electric malfunction
or damage the part.
It may cause electric malfunction
or damage the part.
It may cause electrical leakage.
Is the power cord specified?
It may cause electric malfunction
or damage the part.
Is the inlet and outlet been covered?
It may cause insufficient cooling(heating)
capacity.
Has the length of connection pipes
and refrigerant capacity been recorded?
The refrigerant capacity is not accurate.
Test Operation
1. Before test operation
(1) Do not switch on power before installation isfinished completely.
(2) Electric wiring must be connected correctly and securely.
(3) Cut-off valves of the connection pipes should be opened.
(4) All the impurities such as scraps and thrums must be cleared from the unit.
2. Test operation method
(1) Switch on power, press "ON/OFF" button on the wireless remote control to start
the operation.
(2) Press MODE button, to select the COOL, HEAT (Cooling only unit is not available),
FAN to check whether the operation is normal or not.
23
Installation and Maintenance of Healthy Filter
Installation Instructions
1. Forcibly pull the panel for a specific angle
from the two ends of the front panel according
to the arrow direction. Then pull the air filter
downwards to remove it. (See Fig.a)
Fig. a
2. Mount the healthy filter onto the air filter,(as
shown in Fig.b). If the air filter cannot be installed, please mount the healthy filter on
the front case. (as shown in Fig.c)
Fig. b
Air filter
Healthy filter
Healthy filter
Fig. c
3. Mount the air filter properly along the arrow
direction in Fig.d, and then close the panel cover.
Fig. d
Cleaning and Maintenance
Take out the healthy filter before cleaning and reinstall it after cleaning
according to the installation instruction. Pay special attention to that silver
ion filter can't be cleaned with water, while active carbon, photocatalyst,
low temperature conversion (LTC) catalyst, formaldehyde eliminator, catechin or mite killing filter can, but can't with brush or hard things. Dry it in
the shade or sun after cleaning, but not by wiping.
Service Life
The healthy filter commonly has its usage lifetime for one year under
normal condition. As for silver ion filter, it is invalid when its surface becomes
black (green).
● This supplementary instruction is provided for reference to the unit with
healthy filter. If the graphics provided herein is different from the physical
goods, the latter one shall prevail. The quantity of healthy filters shall be
based on the actual delivery.
24
Configuration of connection pipe and additional volume of refrigerant
1. Standard length of connection pipe
5m、7.5m、8m
2. Min length of connection pipe
For the unit with standard connection pipe of 5m, there is no limitation
for the min length of connection pipe. For the unit with standard connection
pipe of 7.5m and 8m, the min length of connection pipe is 3m.
3. Max length of connection pipe
Sheet 1 Max length of connection pipe
Capacity
Max length of
connection pipe
Capacity
5000 Btu/h
(1465 W)
15
24000 Btu/h
(7032 W)
7000 Btu/h
(2051 W)
9000 Btu/h
28000 Btu/h
15
(8204 W)
36000 Btu/h
Unit: m
Max length of
connection pipe
25
30
(2637 W)
15
(10548 W)
12000 Btu/h
(3516 W)
20
(12306 W)
30
18000 Btu/h
(5274 W)
25
48000 Btu/h
(14064 W)
30
42000 Btu/h
30
4. The calculation method of additional refrigerant oil and refrigerant charging
amount after prolonging connection pipe
After the length of connection pipe is prolonged for 10m at the basis of
standard length, you should add 5ml of refrigerant oil for each additional
5m of connection pipe.
The calculation method of additional refrigerant charging amount (on the
basis of liquid pipe):
(1) Additional refrigerant charging amount= prolonged length of liquid pipe × additional
refrigerant charging amount per meter
(2) When the length of connection pipe is above 5m, add refrigerant according
to the prolonged length of liquid pipe. The additional refrigerant charging
amount per meter is different according to the diameter of liquid pipe. See Sheet 2.
25
Configuration of connection pipe and additional volume of refrigerant
Sheet 2. Additional refrigerant charging amount for R22 R407C R410A
and R134a
Diameter of connection pipe mm
Liquid pipe
Gas pipe
Indoor unit throttle
Outdoor unit throttle
Cooling only,
Cooling only
Cooling and
cooling and heating
(g / m)
heating (g /
(g / m)
Ф6
Ф9.5 or Ф12
m)
20
15
20
Ф6 or Ф9.5
Ф16 or Ф19
50
15
50
Ф12
Ф19 or Ф22.2
100
30
120
Ф16
Ф25.4 or Ф31.8
170
60
120
Ф19
-
250
250
250
Ф22.2
-
350
350
350
Note: The additional refrigerant charging amount in Sheet 2 is recommended
value, not compulsory.
26
SERIES
MODEL
Capacity
BARON
cooling
heating
Hz
V
Power supply
Power current
Power input
EER
COP
Noise‐indoor unit
Noise‐outdoor unit
kW
kW
cooling
heating
cooling
heating
A
A
W
W
W/W
W/W
dB(A)
max
dB(A)
ASH‐09AB
ASH‐12AB
2,6
2,8
50
220‐240
3,64
3,46
821
779
3,21
3,61
40/37/35/32
50
3,2
3,5
50
220‐240
4,45
4,32
1004
973
3,21
3,61
41/38/35/32
52
400
550
m3/h
0,8
1,2
l/h
R410a / 0,7
R410a / 0,8
type / kg
Liquid side inch / mm
¼ / 6
¼ / 6
Pipe diameter
gas side
inch / mm
⅜ / 10
⅜ / 10
Length of connection pipe
max
m
15
20
Elevation/Drop height
max
m
10
10
IU
mm
730x255x174
790x265x177
Dimension (w x h x d)
OU
mm
776x540x320
776x540x320
IU
kg
8
9
Net weight
OU
kg
31
31
18 ~ 43
18 ~ 43
cooling
°C
Operating temperature range
‐7 ~ 24
‐7 ~ 24
heating
°C
The specification of products is subject to change based further development of the units by the producer and can be changed without prior notice.
Air flow
Dehumidifying volume
Refrigerant type / charge
Data are based on following conditions:
Length of connection pipe: 5m
Cooling: indoor temperature 27°C DB/19°C WB, outdoor temperature 35°C DB/24°C WB
Heating condition: indoor temperature 20°C DB/15°C WB, outdoor temperature 7°C DB/6°C WB
SPLIT AIR CONDITIONER
INDOOR UNIT
Model
ASH-09AB
Rated Voltage
220-240V~
Rated Frequency
50Hz
Cooling Capacity
2638W
Heating Capacity
2814W
400m 3/h
Air Flow Volume
Sound Pressure Leve(H)l
37dB(A)
Weight
8kg
Manufactured Date
ISO9001
TUV
Sinclair Corporation Ltd, 1-4 Argyll St., London, UK
63229936851
SPLIT AIR CONDITIONER
INDOOR UNIT
Model
ASH-12AB
Rated Voltage
220-240V~
Rated Frequency
50Hz
Cooling Capacity
3223W
Heating Capacity
3516W
550m 3/h
Air Flow Volume
Sound Pressure Leve(H)l
38dB(A)
Weight
9kg
Manufactured Date
ISO9001
TUV
Sinclair Corporation Ltd, 1-4 Argyll St., London, UK
63229936853
AIR CONDITIONER OUTDOOR UNIT
ASH-09AB
Model
Rated Voltage 220-240V~
(ISO 5151)
50Hz
Cooling Capacity
Rated Frequency
2638W
Heating Capacity
Climate Type
2814W
T1
31kg
Weight
Cooling Power Input
821W
Heating Power Input
Isolation
779W
I
Refrigerant
1000W
R410A Cooling Rated Input
0.66kg
Refri. Charge
Heating Rated Input
1120W
15A
Comp. LRA
Sound Pressure Level
50dB(A)
Maximum Allowable Pressure
5.2MPa
3.8/1.2MPa
Operating Pressure ( Discharge Side/Suction Side)
Manufactured Date
IP24
Moisture Protection
Contains fluorinated greenhouse gases covered by the Kyoto Protocol
TUV
ISO9001
Sinclair Corporation Ltd, 1-4 Argyll St., London, UK
63229936852
AIR CONDITIONER OUTDOOR UNIT
ASH-12AB
Model
Rated Voltage 220-240V~
(ISO 5151)
50Hz
Cooling Capacity
Rated Frequency
3223W
Climate Type
Heating Capacity
3516W
T1
Cooling Power Input
Weight
1004W
31kg
Heating Power Input
Isolation
973W
I
Refrigerant
1450W
R410A Cooling Rated Input
0.84kg
Refri. Charge
Heating Rated Input
1400W
23A
Comp. LRA
Sound Pressure Level
52dB(A)
Maximum Allowable Pressure
6.1MPa
3.8/1.2MPa
Operating Pressure ( Discharge Side/Suction Side)
Manufactured Date
IP24
Moisture Protection
Contains fluorinated greenhouse gases covered by the Kyoto Protocol
TUV
ISO9001
Sinclair Corporation Ltd, 1-4 Argyll St., London, UK
63229936854
Energy
Energy
Manufacturer
Manufacturer
Unit model
ASH-09AB
More efficient
A
A
B
C
D
E
F
G
Less efficient
410.5
( Actual consumption will depend
on how the appliance is used
and climate)
More efficient
A
A
B
C
D
E
F
G
Annual Energy Consumption
kWh in cooling mode
502
( Actual consumption will depend
on how the appliance is used
and climate)
Cooling output
Energy Efficiency Ratio
kW
2.638
3.21
Full load ( the higher the better )
Cooling output
Energy Efficiency Ratio
kW
3.223
3.21
Full load ( the higher the better )
Cooling only
Cooling+Heating
Type
Air cooled
Water cooled
Cooling only
Cooling+Heating
Air cooled
Water cooled
Heat output
Heating performance
A: higher
ASH-12AB
Less efficient
Annual Energy Consumption
kWh in cooling mode
Type
Unit model
kW
G: lower
Noise
(dB(A) re 1 pW)
2.814
ABCDEFG
50/60
Heat output
Heating performance
A: higher
kW
G: lower
Noise
(dB(A) re 1 pW)
Further information is contained
in product brochures
Further information is contained
in product brochures
Norm EN 14511
Air-conditioner
Energy Label Directive 2002/31/EC
Norm EN 14511
Air-conditioner
Energy Label Directive 2002/31/EC
62229924539
3.516
ABCDEFG
51/62
62229924540
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertisement