VRF cassette units ures manual (640x640 mm)

VRF cassette units ures manual (640x640 mm)
Multi Variable Air Conditioners
Cassette Type Indoor Unit Owner’s Manual
This instruction is suitable for the following model:
AMV-R22T/NaA-K
AMVL-R22T/NaA-K
AMV-R28T/NaA-K
AMVL-R28T/NaA-K
AMV-R36T/NaA-K
AMVL-R36T/NaA-K
AMV-R45T/NaA-K
AMVL-R45T/NaA-K
Please read this instruction carefully before operating
Thank you for your selecting of ASAMI air conditioner, please read this usage and
install instruction carefully and keep it well in order to use this unit correctly.
Contents
USER NOTICES
1
Safety information
2
Install the cassette type indoor unit
3
Constitutes and Names of Parts of Cassette Type Indoor Unit
13
Working Temperature Range
13
Wired Remote Controller Operation Procedure
Remote controller
operation procedure
The components of the wired remote control
14
ON/OFF operation
14
Timer setting
15
SLEEP mode setting
16
Swing Control
16
Fan Speed Control
16
Temp. adjusting
17
Set of running mode
17
Malfunction display
17
Ambient Temp Sensor Mode Setting of Indoor Unit
19
Names and functions of every button of the remote control
20
Names and functions of every button of the remote control
(Remove the cover)
21
Operation procedure
22
How to insert batteries
22
Operation Method When Meeting An Emergency
23
Malfunction Debarring
24
Maintenance Method
26
Model and Technical Parameter
29
USER NOTICES
☆
When operating, the entire capacity of the cooperating indoor unit should be not larger than
that of outdoor unit. Otherwise, it will cause the shortage of cooling (heating) capacity.
☆ A Breaker(or fuse) need to be installed in every indoor unit, and the capacity should in
according with indoor unit’s electrical parameter; all the indoor units are required to be
centralized controlled by a total Switch, this Switch can cut off the electric power supply in
case of emergency. The Breaker(or fuse) on each indoor units have the function of short circuit
prevention and abnormal overload avoiding, it should be connected in normal situation. The
total switch controlling the power supply of all the indoor units. Before clearing and
maintenance job being carried out to the indoor units, it is very important to turn off the total
power supply switch.
☆
In order to turn on the units successfully, the main power switch should be opened 8 hours before the
operation.
☆
After receiving the turn off signal, every indoor unit will continue to work for 20-70sec to make use of the
rest cool air or the rest heat air in the heat exchanger, while preparing for the next operation. And this is
normal.
☆
When the selected operating mode of the indoor unit are clash with the operating mode of the outdoor unit,
the malfunction light will blink after 5s on the indoor unit or remote controller showing that the operation
clash, then the indoor unit will stop. At this time, change the operation mode of the indoor unit to the one
that would not clash with the outdoor operating mode to make the operation normal. The cooling mode is
not clash with the dry mode, while the fan mode is not clash with any mode.
☆
The appliance shall not be installed in the laundry
☆
An all-pole disconnection switch having a contact separation of at least 3mm in all poles should
be connected in fixed wiring
☆
Main switch provided by end user: main switch handle should be black or gray, it can be
locked in “OFF” position with padlock
☆
The main disconnection device should be explained in user manual and the height should be
recommended at 0.6-1.7m. over current protection is required(EN 60947-3, EN 60947-2)
☆ The cooling range of the unit is the outdoor environment temp.18-43℃ DB, the heating range
of the unit( only for the heat pump type unit) is the outdoor environment temp. -16-15℃ WB.
1
Safety information
Please read this manual carefully before use this unit, and operate it correctly according to the guide in this manual.
1.
Please take specially note to the meaning of these two marks:
Warning!: This mark means that it may cause casualty or badly heart if the operation is incorrect.
Note!: This mark means that it may cause casualty or property loss if the operation is incorrect.
Warning!
z
Do not adopt fuse with unsuitable capacity or adopt iron thread instead of fuse, otherwise malfunction or fire may
happened.
z
Cut down the main power switch immediately if malfunction (such as smell the burning odor etc.) happened.
z
Maintain ventilation to prevent oxygen leakage in room.
z
Don’t insert finger or stick like things into discharge vent or outlet grill.
z
Please make sure that the unit is installed in the place that can bear the weight of it adequately. If the place is not
strong enough, the air conditioner may drop and cause casualty event.
z
Don’t spray or smear any oil paint or insecticide on the surface of unit, otherwise, fire may be leaded.
z
Do not refit the conditioner. Please contact the agency or prefect ional personnel to repair or move the conditioner.
Note! :
z
Please check and make sure that the cord, drainage pipe and tubes are connected in the correct way to prevent
leakage of water, refrigerant, electric shock or fire.
z
The main power must connectable to the earth in order to assure the conditioner earthing effectively and to prevent
electric shock. Please don’t connect the earthing line with the gas pipe, water pipe, lightening rod or the connecting
line of telephone.
z
The air conditioner should be turned off at least after 5 mins’ operation; otherwise it would affect the duration of the
unit.
z
Don’t let the children operate the air conditioner.
z
Please don’t operate the unit by wet hand.
z
Please turn off the main power of the unit before cleaning the conditioner or change the filter.
z
Please cut off the main power if the conditioner will be used for a long time.
2
Install of the Cassette type indoor unit
● Schematic diagram of installation spaces
H
>20
Wall
surface
Wall
surface
Wall
surface
≥1500
Model
AMV(L)-R22T/NaA-K
AMV(L)-R28T/NaA-K
AMV(L)-R36T/NaA-K
AMV(L)-R45T/NaA-K
≥1800
≥1500
H
230
unit:mm
Ground
surface
Fig.1
● Select install location of the indoor unit
1. Obstruct should put away from the intake or outlet vent of the indoor unit so that the airflow can be blown though all
the room.
2. Make sure that the installation had accord with the requirement of the schematic diagram of installation spaces.
3. Select the place where can stand 4 times of the weight of the indoor unit and would not increase the operating noise
and oscillate.
4. The horizontally of the installation place should be guaranteed.
5. Select the place where easy drain condensated coagulated water, and easy connect with outdoor unit.
6. Make sure that there are enough space for care and maintenance. Make sure that the weight between the indoor unit
and ground is above 1800mm.
7. When installing the steeve bolt, check if the install place can stand the weight 4 times of the unit’s. If not, reinforce
before installation. (Refer to the install cardboard and find where should be reinforced)
Note!
There will be lots of lampblack and dust stick on the acentric, heat exchanger and water pump in dining room and
kitchen, which would reduce the capacity of heat exchanger, lead water leakage and abnormal operation of the water
pump. The following treatment should be taken under this circumstance:
1. Ensure that the smoke trap above cooker has enough capacity to obviate lampblack to prevent the indraft of the
lampblack by the air conditioner.
2. Keep the air conditioner far from the kitchen so that the lampblack would not be indraft by the air conditioner.
3
Install the cassette type indoor unit
● Important notice:
☆ To guarantee the good performance, the unit must be installed by professional personnel according with this
instruction.
☆ Please contact the local ASAMI special nominated repair department before installation. Any malfunction caused by the
unit that is installed by the department that is not special nominated by ASAMI would not deal with on time by the
inconvenience of the business contact.
● Dimension of ceiling opening and location of the hoisting screw (M10)
Install dimension of mode
AMV(L)-R45T/ NaA-K 、AMV(L)-R36T/ NaA-K、AMV(L)-R28T/ NaA-K、AMV(L)-R22T/ NaA-K、
☆ The drilling of holes in the ceiling must be done by the professional personnel.
Ceiling
(160)
Installation stands for m ain body of the unit
Above 20
Fig.2
Notes: The dimension for the ceiling openings with * marks can be as large as 910mm. But the
overlapping sections of the ceiling and the decorated surface boards should be maintained at no less than
20mm.
4
Install of the Cassette type indoor unit
● Main body of hoisting air conditioner
1
The primary step for install the indoor unit.
☆ When attach the hoisting stand on hoisting screw, do use nut and gasket individually at the upper and lower of the
hoisting stand to fix it. The use of gasket anchor board can prevent gasket break off.
2
Use install cardboard
☆ Please refer to the install cardboard about the dimension of ceiling opening.
☆ The central mark of the ceiling opening is marked on the install cardboard.
☆ Install the install cardboard on the unit by bolt (3 piece), and fix the angle of the drainage pipe at the outlet vent by
bolt.
3
Adjust the unit to the suitable install place. (Refer to the fig.2)
4
Check if the unit is horizontal.
☆ Inner drainage pump and bobber switch are included in the indoor unit, check if 4 angle of every unit are horizontal
by water lever. (If the unit is slant toward the opposite of the coagulate water flow, there may be malfunction of the
bobber switch and lead water drop.)
5
Backout the gasket anchor board used to prevent gasket break off and tighten the nut on it.
6
Backout the install cardboard.
Nut (supplied at scene)
Gasket (attachment)
Insert
Hoisting stand
Gasket anchor board
(attachment)
Tighten (double nuts)
[Fix the hoisting stand firmly]
[Fix the gasket firmly]
Bolt of one of the angle of outlet pipe is fix
on the angle of the drainage slot
Center of the ceiling
opening
Install cardboard
Water lever
Bolt (attachment)
Polyethylene pipe
Bolt (attachment)
[Fix the install cardboard]
Note!
●
Please do tighten the nuts and bolts to prevent air conditioner break off.
5
Install of the Cassette type indoor unit
● Connect the refrigerant pipe
☆ When connect the pipe to the unit or backout it from the unit, please do use both spanner and torque wrench. as
shown in fig.3.
☆ When connect, smear both inside and outside of the flare nut with freeze motor oil, screw it by hand and then tighten
it with spanner.
☆ Refer to form 1 to check if the wrench had been tightened (too tight would mangle the nut and lead leakage).
☆ Examine the connection pipe to see if it had gas leakage, then take the treatment of heat insulation, as shown in the
fig.3.
☆ Only use median sponge to entwine the wiring interface of the gas pipe and heat preservation sheath of the gas
collection tube.
Smear freeze motoroil
here
Median sponge (attachment)
(entwine the wiring interface
with seal mat)
Thread fasten(x4)
Torque wrench
Heat preservation
sheath of liquid inlet
tube (attachment) (for
liquid tube)
Spanner
Gas collection tube
Liquid inlet tube
Wiring interface
Heat preservation
sheath of gas collection
tube (attachment)(for
gas tube)
Fig.3
Flare nut
Form 1: The tightening torque needed for tightening nut
Diameter(Inch)
φ1/4’’
φ3/8’’
φ1/2’’
φ5/8’’
φ3/4’’
Surface thickness(mm)
≥0.5
≥0.71
≥1
≥1
≥1
Tightening torque (N.m)
15-30 (N·m)
30-40 (N·m)
45-50 (N·m)
60-65 (N·m)
70-75 (N·m)
● Drainage hose
1.
Install the drain hose
☆ The diameter of the drain hose should be equal or bigger than the connection pipe’s. ( The diameter of polythene
pipe: Outer diameter 25mm Surface thickness ≥1.5mm)
☆ Drain hose should be short and drooping gradient should at less 1/100 to prevent the formation of air bubble.
☆ If drain hose cannot has enough drooping gradient, drain raising pipe should be added.
☆ To prevent bent of the drain hose, the distance between hoisting stand should is 1 to 1.5m.
6
Install the cassette type indoor unit
1-1.5m
○(Correct) 1/100 or more gradient
× (wrong)
☆ Use the drain hose and clamp attached. Insert the drain
Sponge(attachment)
hose to the drain vent, and then tighten the clamp.
Clamp
☆ Entwine the big sponge on the clamp of drain hose to
Clamp(attachment)
insulate heat.
☆
Heat insulation should be done to indoor drain hose.
Drain stepup pipe note
Drain hose
Sponge (gray)
Below 4mm
☆ The install height of the drain raising pipe should less
than 280mm.
☆ The drain raising pipe should form a right angle with the unit, and distance to unit should not beyond 300mm.
Roof
Within 300mm
Hoisting stand
below280mm
1-1.5m
.
220mm
Ceiling
below500mm
Drain raising
hose
.
Drain hose
Clamp(attachment)
Instruction
D ra in h o s e (a tta c h m e n t)
.
outside force.
☆ Please install the drain hose according to the following process
if several drain hoses join together.
T-tie in join drain hose
.
Above100mm
The specs of the selected join drain hose should fits the running capacity of the unit.
7
below500mm
75mm so that the drain hole doesn’t has to endure the unnecessary
below75mm
☆ The slant gradient of the attached drain hose should be within
Install the cassette type indoor unit
2
Check the smoothness of drain after installation.
☆ Check the drain state by immitting 600cc water slowly from the outlet vent or test hole.
☆ Check the drain in the state of refrigerating after installation of the electric circuit.
8
Install the cassette type indoor unit
● Electrical wiring
Note: The power of the entire indoor unit must be unity power supply
☆ About the electrical wiring, please see the circuit diagram attached with the unit.
☆ All the installation of electrical wiring must be done by professional personnel.
☆ Please do take the earthing treatment.
Wiring method of connection unit and controller
☆ Connection wiring (communication):
① Open electric box cover, drag the wiring (communication)from the rubber plug A, and impact them well individually
by impact fastener.
② Wiring according to the indoor side circuit diagram.
☆ Fix the impact fastener after connection.
☆ Entwine the small sponge on the electric wire ( do entwine it to prevent condensation)
☆ Impact tightly by impact fastener after connection and then fit on the electric box.
N
L
☆ Connect the 3 cord rubber wire to the counter terminal of the 3 way terminal board.
L
N
power supply
3 way terminal board
3 core rubber wire
3 core rubber wire
Impact fastener
9
Install the cassette type indoor unit
● Function description of functional dial switch S7
1. The 3-bit dial switch must be set before energizing the main board and it determines running state of indoor unit.
2. Function of it is as follow:
Dial switch
Silk screen
1(S / R)
Function
Dial ON
Dial OFF
Standby after
Reset after
energizing
energizing
Selection between manual controller and receiver
A:If manual controller is selected, remote-control function of receiver
Selecting
Selecting
will be shielded.
B:If receiver is selected, wired controller will be non-effective.
wired
receiver
controller
joint
Main indoor
Slave indoor
unit
unit
Selection of memory mode:
A:Selection between reset mode and standby mode after energizing
B:This function is available without wired controller.
2(L / I)
3(M / S)
Setting of main and slave indoor units
A:For resolution of conflict among the modes.
B:This function is available without wired controller.
10
Install the cassette type indoor unit
● Install the panel
1. Set the panel to the indoor unit body by matching the position of the swing flap motor of the panel to the piping
position of the panel to the piping position of the indoor unit as shown by fig.4.
2. Install the panel
① Screw the 4 hexagon head screws under the latches in about 15mm. (The panel would rise)
② Adjust the panel by turning it toward the direction pointed by the arrow as shown in fig.4, so that the adjust
board connect the ceiling well.
③ Tighten the screws until the thickness of the sealing material between panel and indoor unit reduced to 5-8mm.
Piping position
Swing flap motor
Bolt (attachment)
①
②
Bolt (attachment)
Sealing material
Indoor unit
.
Ceiling
Air outlet vent
Fig 4
11
5mm to 8mm
③
Decoration panel
Install the cassette type indoor unit
Note
1. Improper screwing of the screws may cause the troubles shown in fig.5.
Air leak
Air leak from ceiling
Water condensatation, water drop
Fig.5
2. If gap still exist between ceiling and decoration panel after tightening the screws, readjust the height of the indoor unit.
(As shown in fig.6)
If the raising lever and drain hose are
not affect, can adjust the height of
indoor unit by the hole on the corner
of panel.
Gaps are not allowed
Fig.6
※ After fixing, be sure no gap left between the ceiling and the panel.
3. Wiring of the decoration panel (Fig.7)
☆ Connect the joints for swing flap motor lead wire (at 2 places) installed on the panel.
At body
At body
At pane
Fig.7
12
At pane
Constitutes and Names of Parts of Cassette Type Indoor Unit
Drainage equipment (inside type)
Discharge condensate water from
indoor unit when cooling
Drainage hose
Guide louver
(placed in air
outlet vent)
Air outlet vent
Connecting pipe
Air filter, purifier (in
air inlet grille)
Air inlet grille
AMVL-R22T/ NaA-K
AMVL-R28T/ NaA-K
AMVL-R36T/ NaA-K
AMVL-R45T/ NaA-K
AMV-R22T/NaA-K
AMV-R28T/NaA-K
AMV-R36T/NaA-K
AMV-R45T/NaA-K
Working Temperature Range
Working Temperature Range
Indoor side state
Dry bulb temp.
Wet bulb temp.
℃
℃
Outdoor side stae
Wet bulb temp.
Dry bulb temp. ℃
℃
Rated Cooling
27
19
35
24
Max. cooling
32
23
43
26
Min. cooling
21
15
18
—
Rated Heating
20
15
7
6
Max. heating
27
—
24
18
Min. heating
20
15
-15
-16
13
Wired Remote Controller Operation Procedure
The components of the wired remote control
MODE
FAN
SWING
TIMER
ON/OFF
Fig.1
Every part of wired remote controller
1
Operating mode display (Cool, Dry, Fan,
Heat)
9
On/Off button
2
Sleep mode display
10
Timer button
Environmental
temp.
display
/
Malfunction display
Fan control display (automatic, high,
media, low)
11
3
4
Swing button
12
Swing display
5
Set Temp. display
13
Fan control button
6
Defrosting display
14
Temp. / Timer reducing button
7
Timer display
15
Temp. / Timer rising button
8
Signal receptor
16
Mode button
1) On/Off(Fig.2)
™ Press On/Off button to turn on air conditioner.
●
MODE
Repress On/Off button once to turn off air conditioner.
Note:The displaying in fig.2 is the turned off state after connecting
with
power
supply.
After
connecting
power
and
FAN
normal
SWING
communication, the environmental temp. will be displayed on LCD
TIMER
under state of both turned on or off. At this time, as shown in fig.3
ON/OFF
there is no pane displayed on LCD, which means that the air
conditioner is turned off.
Fig2
14
Wired Remote Controller Operation Procedure
2)Timer setting(Fig.3,the following sketch is displayed according
to the functions of wired remote controller)
™
Press TIMER under off state can set On Time; press TIMER
MODE
under on state can set Off Time.
™
Under the circumstance that without setting time ( there isn’t
information in the Timer Time Display Zone), press TIMER, then
xx.x Hours”, and the
the LCD will display the pattern of “
FAN
”and“hours”will keep blinking for 0.5s, press adjusting
SWING
button“▲”or“▼”can adjust set time. After adjusting set time by
TIMER
“
button “▲”or“▼”, repress TIMER once, the pattern“
”and
ON/OFF
“hours” will no longer blinking, which indicates that TIMER
Fig3
had been set.
™
Press TIMER once after electrify, “
0.0 hour” is displayed and both of the two patterns are blinking on LCD,
repress TIMER once again, then the Timer pattern no loner displayed on LCD, which indicated that the TIMER
setting had been cancelled.
™
Under the circumstance of TIMER time had been set ( i.e. the state that “
TIMER, then the "
”and“hours”don’t blink), repress
xx.x hours” will be redisplayed on LCD (note:
“xx.x” indicates the set time of last time, and
will be cancelled after electrify), and both “
”and “hours”are blinking, at this time, adjust “▲”or“▼”to reset
timer, or repress TIMER to confirm timer function.
™
The timer of turning on/off ranged from 0.5-24 hours. Every single press of“▲”or“▼”, the set time will be
added or subtracted 0.5 hour. Press“▲”or“▼”serially the set time will add or subtract 0.5 hour
automatically for every 0.5s. The adjusting range of“▲”and“▼”are from 0 to 24, and the mode is
recycling mode.
Button“▲”:
0.0
0.5
Button“▼”:
0.0
0.5
1.0
1.0
······
······
Note:The above displayed is the relative displaying zone.
15
23.5
23.5
24.0
24.0
Wired Remote Controller Operation Procedure
3)SLEEP mode setting(fig.4)
™ When under the cooling or dehumidifying mode, after
MODE
receiving the SLEEP order for 1 hour, the previous set temp.
Tset will be risen for 1℃, and another 1℃ will be risen
after 2 hours that means that the temperature been risen 2℃
within 2 hours. Then the unit will run according to this set
FAN
temp.
SWING
™ When under the heating mode, after receiving the SLEEP
TIMER
order for 1 hour, the previous set temp. Tset will be lower
ON/OFF
for 1℃, and another 1℃ will be lower after 2 hours that
means that the temperature been lowered 2℃ within 2
Fig4
hours. Then the unit will run according to this set temp.
™ There is no SLEEP mode under fan mode.
MODE
Note:The wired remote controller has no SLEEP mode button;
if SLEEP mode is needed to be set, complete the procedure by
wireless remote controller.
FAN
4) Swing Control(Fig.5)
SWING
™ Press Swing button then the swing mode will be
TIMER
operated by the air conditioner.
ON/OFF
™ Repress Swing button once to stop swing mode.
Note: There is no swing mode for duct type indoor unit
Fig5
5)Fan Speed Control(fig.6)
™ Every press of the fan speed button, the fan speed will be
MODE
changed according to the following order:
Auto
Low
Medium
High
FAN
SWING
™ Under dehumidifying mode:Fan speed will be set to low
automatically.
TIMER
ON/OFF
Fig6
16
Wired Remote Controller Operation Procedure
6)Temp. adjusting(Fig.7)
™ Under the state without time setting, press“▲”and“▼”to
adjust temp..
▲:To rise set temp.;
MODE
▼:To reduce set temp.
( every press of this button, temp. will be risen or
subtracted for 1℃.)
FAN
™ Temp. adjusting ranged from 16 ℃ ~ 30 ℃ under any
SWING
running mode.
TIMER
7)Set of running mode(Fig.8)
ON/OFF
™ Every once press of the mode key, the running mode would
be changed according to the following order:
COOL
DRY
FAN
Fig7
HEAT
™ Under cooling mode, the display of cooling will on, and the
MODE
set temp. should be lower than the present room temp. If the
set temp. is higher than the present room temp., air
conditioner would not enter cooling mode.
FAN
™ Under dehumidify mode, display of dehumidify will on.
Fan will run in low speed in certain temp. range. The
SWING
dehumidifying effect of this mode is better than that of
TIMER
cooling mode, and saves more energy.
ON/OFF
™ Under heating mode, the display of heating will on. The set
temperature should be higher than that of present room; if
Fig8
the set temp. was lower than that of present room, heating
mode would not be operated.
MODE
™ Under fan mode, the display of fan will on.
8)Malfunction display(fig.9)
™
When malfunction happened in running, malfunction code will
FAN
be shown in environmental temp. display zone. Fig.9 indicates
™
that the compressor is operating high pressure protect.
SWING
When malfunction happened, except fan mode will still work in
TIMER
normal, outdoor unit and fan will close under mode of cooling,
ON/OFF
dehumidify and heating, but LCD display will not be affected.
Fig9
17
Wired Remote Controller Operation Procedure
™
When controller displaying malfunction, please turn off the unit to stop displaying and has it repaired by specialized
personnel.
The meaning of malfunction code is as following:
Malfunction code
Malfunction
E1
High pressure protection of compressor
E2
Indoor anti-frozen protection
E3
Low pressure protection of compressor
E4
Discharge temp. protection of compressor
E5
Compressor overload protection
E6
Transmit malfunction
E7
Modes conflict
F0
Indoor environment temp. sensor mal-function
F1
Indoor pan tube inlet tube temp. sensor malfunction
F2
Indoor pan tube middle temp. sensor malfunction
F3
Indoor pane tube outlet tube temp. sensor malfunction
F4
Outdoor environment temp. sensor malfunction
F5
Outdoor pan tube inlet tube temp. sensor malfunction
F6
Outdoor pan tube middle temp. sensor malfunction
F7
Outdoor pan tube outlet tube temp. sensor malfunction
F8
Discharge temp. sensor 1 (rated frequency) malfunction
F9
Discharge temp. sensor 2 (digital) malfunction
FA
Greasy temp. sensor 1 (rated frequency) malfunction
Fb
Greasy temp. sensor 2 (digital) malfunction
Fc
High pressure sensor malfunction
Fd
Low pressure sensor malfunction
18
Ambient Temp Sensor Mode Setting of Indoor Unit
Please refer to Use Instruction for Indoor Unit about this function’s
actual initial status.
Under off state of unit, press FAN and SLEEP/SWING buttons at the same time for 5s into setting interface, as
shown in Fig.10.“01” is displayed in ambient temp displaying area and setting mode code is displayed in temp
displaying area which can be adjusted by pressing ▲ or ▼, 4 kinds of selection:
①:Indoor ambient temp is air inlet temp and setting temp area displays 01, as shown in Fig.11.
②:Indoor ambient temp is wired controller temp and setting temp area displays 02, as shown in Fig.12.
③:Under heating mode, select wired controller’s temp sensor or under other modes select air inlet’s temp sensor
and setting temp area displays 03, as shown in Fig.10.
④:Under heating mode, select air inlet’s temp sensor or under other modes select wired controller’s temp sensor
and setting temp area displays 04, as shown in Fig.13.
Factory default is the third mode, as shown in Fig.10.
Fig.10
Fig.11
Fig.12
Fig.13
19
Remote controller operation procedure
Names and functions of every button of the remote control
The remote control of the Ducked type indoor unit is shop piece.
NOTE!
● Make sure that there is no obstruction between the remote control and the signal receptor.
● The remote control signal can be received at the distance of up to about 10m.
● Don’t drop or throw the remote control.
● Don’t let any liquid flow into the remote control.
● Don’t put the remote control directly under the sunlight or any place where is very hot.
SWING button
the guide louver swings
according to certain
angle when press once;
repress once to stop
operating.
FAN button
Press the button to
change the speed of the
fan according to the
following order.
SWING
AUTOFAN
TEMP. button
Set temp. increases 1 c
by pressing "+" and
decreases 1 c by pressing
"-" once.
Set temp. : 16 c~30 c
Set temp. : 16 c~30 c
FAN
AUTO FAN
SPEED
OPER
AUTO
AIR
SWING HUMID LIGHT SAVE
TIMER
ONOFF
HR.
COOL
DRY
FAN
HEAT
Set temp. : 16 c~30 c
Set temp. : 16 c~30 c
ON/OFF button
Press the button to turn on
the unit. Press the button
once again to turn off the
unit and cancal the timer.
MODE button
Press the button to change
the mode according to the
following order
MODE
ON/OFF
NOTE: The cooling only
units have no
mode.
NOTE!
After every indoor unit received the turn off signal, the fan and electric inflate valve will continue to
work for 20-70mins to make use of the rest cool or rest heat, while for preparation for the nest work. And
this is normal phenomenon.
20
Remote controller operation procedure
Names and functions of every button of the remote control (Remove the cover)
NOTE!
This type of remote control is a kind of general use remote control that is suitable for several types
(function) of air conditioner units. Please understand that the functions and buttons that are not suitable
for this air conditioner will not be introduced.
Liquid crystal displayer
It shows all set contents.
SWING
FAN
AUTOFAN
SLEEP button
Press the button to set SLEEP
mode, and stop when repressed.
When the sleep mode is in the
cool and dry mode, the set
temp. will increases 1~2℃
during the set time, then the
unit will operate according to
the temp.. When sleep mode is
in the heat mode, the set temp.
decreases 1~2℃ during the set
time, then the unit will operate
according to the set temp..
OPER
AUTO
AIR
SWING HUMID LIGHT SAVE
TIMER
ONOFF
HR.
SLEEP
AIR
LIGHT
HUMID
TIMER ON TIMER OFF
MODE
ANION
SAVE
ON/OFF
Temp./Timer button
When the unit is operating, increase 1℃
by pressing "+" button once, and
decrease 1℃ by pressing "-" button
once. The indoor temp. can be set in
the range of 16-30℃.
Press the "Timer OFF/TIMER ON"
button at operating/ stopping to set the
off/on time. Press "Timer OFF/TIMER
ON" once to increase 0.5 hour for the
set time. The longest set time is 24
hours; repress it once to cancel timer.
21
Remote controller operation procedure
Operation procedure
Normal procedure
1. Press ON/OFF button after connected with the power, then the unit is operating.
2. Press MODE button to choose the need operation mode.
3. Press button SWING to make the guide louver swings according to certain angle when press once; repress once to
stop operating.
4. Press FAN button to set the fan speed.
5. Press +/- button to set the need temp..
Selectable procedure
6. Press SLEEP mode to set the sleep state.
7. Press TIMER OFF button to set the set time.
8. Repress ON/OFF turn off indoor air conditioner. Under cooling and dehumidify mode, rest cool air will be blow for
20~70s; Rest heat air will be blow for 60s under heating mode.
Note: When the operating mode selected by the indoor unit is clash with the one selected by the outdoor unit, the
remote controller will display the operating clash after 5 seconds and the power light will flicker, then the indoor
unit turns off. At this time, the units will become normal after the operating mode of the indoor unit is changed to
cooperate with the outdoor unit. Cool mode can cooperate with dry mode, and fan mode can cooperate with any
mode.
How to insert batteries
Two batteries( Two AAA dry-cell batteries) are used by the remote control
1. Remote the cover from the back of the remote control downward, take out the worn batteries and insert two new ones
(Make sure the two poles are correct)
2. Re-attach the cover.
ACL
1.All the prints and code no. will
be showed on the displayer after
the insert of batteries. The remote
control can be operated after 10sec.
2.The lifetime of the batteries is
about one year.
3.Don't confuse the new and worn
or different types of batteries.
4.Remove batteries when the
①Remove the cover remote control is not in use for a
③Re-attach the cover longtime to avoid mal-function
caused by liquid leakage.
5.The remote control should be
placed about 1m or more from the
open
TV set or any other electric
appliances.
6.The remote control should be
used in the receivable range (the
RESET KEY
reception range is 10m)
7.When the remote control can not
be controlled in the situation of
inserted batteries, please remove
the back cover and press "ACL"
button to make it normal.
②Insert 2AAA dry-cell
battaries(attachment)
22
Operation Method When Meeting An Emergency
● Operation Method When Meeting An Emergency
When wireless remote controller is lost or damaged, the following method could be adopted to control cassette type
indoor unit:
☆ When the unit is turned off, press AUTO button on corner outer coverⅡ, then the unit begin operate in cooling with
the fan run in high speed. The temp. will be set to 26℃ automatically.
☆ When the unit is turned off, press TEST button on the corner outer coverⅡ, then the unit begin running in heating
and the fan is running in high speed. The temp. will be set to 20℃ automatically.
☆ When the unit is running, press AUTO button on corner outer coverⅡ, then the unit stops running; under the running
state of heating, press TEST button on corner outer cover Ⅱ, then the unit stops running.
Note!
Prevent using the operating method for meeting an emergency when the wireless remote controller could be used in
normal. There are 3 lights on corner outer cover Ⅱ, red for power, green for running, and yellow for timer.
TO
AU
T
TES
23
Malfunction Debarring
Warning!
z
Cut down the main power switch immediately if malfunction (such as smell the burning odor etc.) happened, and
then contact service center. If the abnormal state is maintained, the unit may be damaged or electric shock or fire
may be happened.
z
Do not refit the conditioner. Please contact service center to repair or move the conditioner.
●
Check the following items before contacting maintenance center
Phenomena
Air conditioner doesn’t
run at all
Air conditioner runs but
stops immediately
Reason
Remedial Measures
Blow of fuse or breaker
Change fuse or close breaker
Power cut
Restart when there is power supply
Don’t connect with power
Connect power well
Low batteries of wireless remote controller
Change new batteries
Wireless remote controller exceed remote
control area
Blockage in inlet or outlet vent of indoor
or outdoor unit
Blockage in inlet or outlet vent of indoor
or outdoor unit
Improper of temp. setting
Low setting of fan speed
Incorrect of wind direction
Abnormal cooling or
heating
Signal could be received within 8m
Clean out blockage
Clean out blockage
Adjust settings in wireless remote
controller
Adjust settings in wireless remote
controller
Adjust settings in wireless remote
controller
Door or window opened
Close
Direct sun burn
Hang curtain or jalousie before windows
Too many people in room
Too many heater in room
Filter blocked by dirt
●
Clean filter
Instruction
If problem still cannot found out after above checking, please contact service center and instruct phenomena and
model.
24
Malfunction Debarring
●
The following circumstance are not malfunction
“Malfunction”
Reason
Start up unit immediately after turned off
The overload protects switch makes it run
after 3 minutes delay.
When opening power
Run for about 1 minute without other
actions
When cooling
The high humidity air in room is cooled
rapidly
Slight click sound heard once begin
running
Sound of initialization for electric expand
valve
Hissing sound heard continuously when
cooling
The sound for gas refrigerant flowing in
the unit
Hissing sound heard when staring or
stopping
The sound for gas refrigerant stops flow
Slight hissing sound heard when running
or after running
Sound for running of drainage system
Creak sound heard when running or after
running
The grating sound caused by expands of
panel and other parts for the change of
temperature
Dust be blown for air
conditioner
Started up after long time’s doesn’t runs
Dust in indoor unit be blown out
Odor gives out from air
conditioner
When running
This is because when air conditioning,
odors or cigarette smoke from the room
that was sucked in is discharged again.
Air conditioner doesn’t
run
Mist is blown from air
conditioner
Noise is heard from air
conditioner
●
After-sales Service
☆ When having quality or other problems when purchasing air conditioner, please contact the local service center.
25
Maintenance Method
When air conditioner won’t be used for a long time, please cut off the main power supply of air
conditioner.
Warning!
z
Do turn off the unit and cut off the main power supply when cleaning the air conditioner, otherwise electric shock
or harm may happen.
z
It is forbidden to wash air conditioner by water rinsing, otherwise electric shock may happen.
●
Cleaning air filter
When the usage environment has lots of dust, air filter should be cleaned more frequently (about once 6 months).
1. Open air inlet grille
Pull the 2 handle on air inlet grille at the same time with the direction showed by arrow in fig. I, pull down slowly.
(Reverse when closing)
2. Disassembly air filter
As shown in fig. II, pull the handle behind air inlet grille, raise it and disassembly. Then discharge the 3 purifier
fixed on filter.
purifier
Fig. I
Fig. II
3. Clean
Adopts cleaner or water to wash filter; if the filter is too dirty ( like oil stain on it ), adopts warm water ( lower
than 45℃) with neutral scourer to clean it, then dry it in the shade.
Note!
z
Do not clean the filter by hot water whose temp. is higher than 45℃ to prevent fade or deformation.
z
Do not burn it on fire or the filter would catches fire or deformation.
4. Install air filter
Fix the 3 purifiers on filter, install filter on the several bulges on top of air inlet grille, pull the handle behind air
inlet grille toward inside to fix filter. As shown in fig. III.
5. Close air inlet grille (Refer to the 1st step)
26
Maintenance Method
Fig. III
●
Fig. IV
Clean air inlet grille
1. Open air inlet grille (the same with the 1st step of Clean Air Filter)
2. Take out air filter (the same with the 2nd step of Clean Air Filter)
3. Take out air inlet grille
Open air inlet grille for an angle of 45°, as shown in fig. IV, rise it.
4. Clean
Clean it by pubescence brush, water and neutral cleaning, then throw water or dry it.
Note!
z
Do not use water above 45℃ to wash the panel to prevent fade or deformation.
5. Install air inlet grille (refer to 3rd step)
6. Install air filter (refer to the 4th step of Clean Air Filter)
7. Close air inlet grille (refer to the 1st step)
●
Install and change of air purifier
1. Open air inlet grille (the same the 1st step of Clean Air Filter)
2. Disassembly purifier
Air filter
As shown in fig V, disassembly air filter, screw out fixing bolts fixed
on purifier on filter, then purifier could be disassembly.
Purifier filter
3. Take out the package sack of static fiber net filter, then install the
Stand for purifier
filter in stand of purifier, and fix purifier on air filter.
4. Install air filter (the same with the 4th step of Clean Air Filter)
Fix bolt of
purifier
Fig. V
27
Maintenance Method
Function and usage period for air purifying
☆ Could adsorb CO, CO2, benzene, aldehydes and odor of gasoline etc..
☆ Could adsorb deleterious material that is smaller than 1μm in air, as dust, pollen, bacteria, and virus.
☆ Usage period is 6 months to 1 year. If it is necessary to be changed, purchase new purifier in the nearest ASAMI special
engaged maintenance center.
● Clean Outlet vent and Surface Panel
☆ Clean the surface panel by soft dry cloth or wet cloth with neutral scourer.
☆ It is forbidden to clean surface panel by gasoline, benzene, diluents, cleansing powder etc..
☆ If the guide louver is too dirty, it may be removed to be cleaned. (As narrated below)
Disassembly and install of guide louver
1. Disassembly guide louver
Screw bolts in both end of guide louver to loose.
Note!
z
Do not wipe guide louver powerfully when cleaning, otherwise fluff on surface would fall off.
2. Install guide louver
Rotate guide louver slightly could install the protruding edge of both end into grooves on both end of guide louver,
and then tighten bolts.
● Maintenance before or after usage season
Check before the usage season
☆ Check if there is blockage in inlet or outlet vent of air conditioner.
☆ Check if the earthing wire had earthed reliably.
☆ Check if the air filter had been installed well.
☆ In order to start up the air conditioner smoothly after long time’s turned off, turn on the main power supply 8 hours
before turning on the air conditioner.
Maintenance after usage season
☆ Clean filter and body of air conditioner.
☆ Cut off the main power supply of air conditioner.
28
Model and Technical Parameter
● Parameter of cassette type indoor unit
Model
AMVLR22T/NaA
-K
AMVR22T/NaA
-K
AMVLR28T/NaA
-K
AMVR28T/NaA
-K
AMVLR36T/NaA
-K
AMVR36T/NaA
-K
AMVLR45T/NaA
-K
AMVR45T/NaA
-K
Function
Cooling
only
Cooling
and
heating
Cooling
only
Cooling
and
heating
Cooling
only
Cooling
and
heating
Cooling
only
Cooling
and
heating
2.2
2.2
2.8
2.8
3.6
3.6
4.5
4.5
—
2.5
—
3.2
—
4.0
—
5.0
Air Flow Rate(m3/h)
600
600
600
600
600
600
600
600
Sound Level(dB(A))
47
47
47
47
47
47
47
47
Input of Motor(kW)
0.012
0.012
0.012
0.012
0.012
0.012
0.012
0.012
Cooling Capacity
(kW)
Heating Capacity
(kW)
Power Supply
220-240V~ 50Hz
Anti-electric Shock
Protect Type
I
Dimensions(mm)
(W×D×H)
Main body:570×570×230
Panel:650×650×50
Net Weight(kg)
(Main body/Panel)
20/5
☆ The above performance parameter is measured according to the standard of GB/T18837-2002, and its cooling or
heating capacity and sound level are tested before leaving factory.
☆
If the parameter changed, refer to the data offered on nameplate.
29
66129911517
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertisement