Heat & Glo Villa Gas Installation manual

Add to My manuals
22 Pages

advertisement

Heat & Glo Villa Gas Installation manual | Manualzz

Installation Manual

Installation and Fireplace Setup

Pour demander un exemplaire en français de ce Manuel du propriétaire, visitez www.

heatnglo.com/translations.

INSTALLER: Leave this manual with party responsible for use and operation.

OWNER: Retain this manual for future reference.

NOTICE:

DO NOT discard this manual!

DANGER

If you smell gas:

1. Shut off gas to the appliance.

2. Extinguish any open flame.

3. If odor continues, keep away from the appliance and immediately call your gas supplier or fire department.

Model(s):

ODVILLAG-36T ODVILLAG-36H

ODVILLAG-42T ODVILLAG-42H

Outdoor Decorative Gas Appliance

WARNING

HOT SURFACES !

Glass and other surfaces are hot during operation AND cool down.

Hot glass will cause burns.

• DO NOT touch glass until it is cooled

• NEVER allow children to touch glass

• Keep children away

• CAREFULLY SUPERVISE children in same area as fireplace.

• Alert children and adults to hazards of high temperatures.

High temperatures may ignite clothing or other flammable materials.

• Keep clothing, furniture, draperies and other flammable materials away.

WARNING

Do not store or use gasoline or other flam mable vapors and liquids in the vicinity of this or any other appliance

An LP-cylinder not connected for use shall not be stored in the vicinity of this or any other appliance.

Improper installation, adjustment, alteration, service or maintenance can cause injury or property damage. Read the installation, operating and maintenance instructions thoroughly before installing or servicing this equipment.

This appliance is only for use with the type(s) of gas indicated on the rating plate. This appliance is not convertible for use with other gases, unless a certified kit is used.

NOT for use with solid wood fuel.

Outdoor Lifestyles • Villa Gas Owners/Installation Manual • 4072-170 • Rev Q • 08/18 1

Safety Alert Key:

• DANGER!

Indicates a hazardous situation which, if not avoided will result in death or serious injury.

• WARNING!

Indicates a hazardous situation which, if not avoided could result in death or serious injury.

• CAUTION!

Indicates a hazardous situation which, if not avoided, could result in minor or moderate injury.

• NOTICE: Indicates practices which may cause damage to the fireplace or to property.

Table of Contents

1 Welcome

A. Congratulations

Listing Label Information/Location

B. Warranty

2 Product Specific & Important Safety Information

A. Appliance Certification

B. BTU Specifications

C. Non-Combustible Materials

D. Combustible Materials

E. High Altitude Installations

3 Getting Started

A. Design and Installation Considerations

Moisture Resistance

B. Inspect Appliance and Components

7

7

7

7

7

8

8

8

4 Framing and Clearances

A. Appliance Dimension Diagram

B. Clearances to Combustibles

C. Constructing the Appliance Enclosure

D. Vent Termination Minimum Clearances

E. Securing and Leveling the Appliance

F. Non-Combustible Material Installation

4

4

5

9

10

11

12

13

13

5 Gas Information

A. Fuel Conversion

B. Gas Pressure

C. Gas Connections Provision

D. High Altitude Installations

E. Air Shutter Setting

14

14

14

15

15

6 Finishing

A. Facing Material

B. Mantel and Wall Projections

Mantels

Mantel Legs or Wall Projections

7 Appliance Setup

A. Remove the Shipping Materials

B. Clean the Appliance

D. Install Gas Hearth Kit (provided)

E. Install Mesh Door (optional)

8 Maintenance and Service

9 Reference Materials

A. Service Parts

B. Accessories

C. Contact Information

21

25

26

19

19

19

19

16

17

17

18

2 Outdoor Lifestyles • Villa Gas Owners/Installation Manual • 4072-170 • Rev Q • 08/18

ATTENTION INSTALLER:

Follow this Standard Work Checklist

This standard work checklist is to be used by the installer in conjuction with, not instead of, the instructions contained in this installation manual.

Customer:

Lot/Address

Date Installed:

Location of Appiance

Installer:

Dealer/Distributor Phone #

Model (circle one): ODVILLAG-36T

ODVILLAG-36H

ODVILLAG-42T

ODVILLAG-42H

Serial #:

WARNING! Risk of Fire or Explosion!

Failure to install fireplace acording to these instructions can lead to a fire or explosion.

Appliance Install

The enclosure is sealed. (Pg. 8)

Required non-combustible board is installed (if applicable). (Pg. 13)

Verified clearances to combustibles. (Pg. 10)

Appliance is leveled and secured. (Pg. 12)

YES IF NO, WHY?

Finishing Section 6 (Pg. 16)

Combustible materials not installed in non-combustible areas.

Verified all clearances meet installation manual requirements.

Mantels and wall projections comply with installation manual requirements.

Appliance Setup Section 7 (Pg. 18)

All packaging and protective materials removed.

Refractory, logs, media and embers installed correctly.

Optional mesh doors properly installed.

Manual bag and all of its contents are removed from the fireplace and given to the party responsible for use and operation.

Started appliance and verified no gas leaks exist.

Hearth & Home Technologies recommends the following:

• Photographing the installation and copying this checklist for your file.

• That this checklist remain visible at all times on the fireplace until the installation is complete.

Comments: Further description of the issues, who is responsible (Installer/Builder/Other Trades, etc.) and corrective action needed:

Comments communicated to party responsible __________________________ by ______________________on _________

(Builder/Gen. Contractor) (Installer) (Date)

4072-171 • Rev B • 09/28/15

Outdoor Lifestyles • Villa Gas Owners/Installation Manual • 4072-170 • Rev Q • 08/18 3

1

Welcome

Read this manual before installing or operating this fireplace.

Please retain this owner’s manual for future references.

A. Congratulations

Congratulations on selecting a Outdoor Lifestyles decorative gas appliance. The HHT gas appliance you have selected is designed to provide the utmost in safety and reliability.

As the owner of a new gas appliance, you'll want to read and carefully follow all of the instructions contained in this

Owner's Manual. Pay special attention to all Cautions and

Warnings.

This Owner's Manual should be retained for future reference. We suggest that you keep it with your other impor tant documents and product manuals.

Your new Outdoor Lifestyles decorative gas appliance will give you years of durable use and trouble-free enjoyment.

Outdoor Lifestyles is a registered trademark of Hearth &

Home Technologies.

DEALER: Fill in your name, address, phone and e-mail information here and fireplace information below.

Local Dealer Information

Dealer Name: ________________________________________________________

Address: ____________________________________________________________

____________________________________________________________

Phone: _____________________________________________________________

E-mail: _____________________________________________________________

Fireplace Information:

Brand: ________________________________________________ Model Name: ___________________________

Serial Number: __________________________________________ Date Installed: __________________________

Listing Label Information/Location

The model information regarding your specific fireplace can be found on the rating plate usually located in the control area of the fireplace.

Serial

Number

Fireplace

Model

This appliance must be installed in accordance with local codes, if any; if not, follow ANSI

Z223.1 in the USA installation codes.

ANSI Z21.97-2012

CSA 2.41-2012

Outdoor Decorative

Gas Appliances

Serial (Serie) :

OD *

Mfg. Date:

Outdoor Lifestyles by

Hearth & Home Technologies

7571-215th St. West, Lakeville, MN 55044 29LD

Outdoor decorative gas appliance - for outdoor use only. Not for use with solid fuel.

(Foyer au gaz à évacuation - pour installation à l'extérieur seulement. Ne doit pas entre utilise avec un combustible solide.)

Minimum Permissible Gas Supply for Purposes of Input Adjustment. Natural Gas Propane Gas

Approved Minimum (De Gaz) Acceptable . . 7.0 in. w.c. (Po. Col. d'eau) . . .11.0 in. w.c. (Po. Col. d'eau)

Maximum Pressure (Pression) . . . . . . . . . . 10.0 in. w.c. (Po. Col. d'eau) . .14.0 in. w.c. (Po. Col. d'eau)

Maximum Input BTUH (36 in.): . . . . . . . . . . 40,000 . . . . . . . . . . . . . . . . . . .40,000

Maximum Input BTUH (42 in.): . . . . . . . . . . 42,000 . . . . . . . . . . . . . . . . . . .42,000

!

or maintenance can cause injury or property damage. Refer to the owner’s information manual provided with this appliance. For assistance or additional information, consult a qualified installer, service agency or the gas supplier.

!

vapors and liquids in the vicinity of this or any other appliance.

An LP-cylinder not connected for use shall not be stored in the vicinity of this or any other appliance.

Model

(Modele) :

MADE

IN USA

ODVILLAG-36H

ODVILLAG-42T

ODVILLAG-42H

This product is covered by one or more of the following patents: (Nos produits sont couverts par un ou plusieurs des brevels suivants) : (United States) 4,112,913; 4,408,594; 4,422,426; 4,424,792; 4,520,791; 4,793,322; 4,852,548; 4,875,464; 5,000,162; 5,016,609; 5,076,254; 5,191,877;

5,218,953; 5,328,356; 5,429,495; 5,452,708; 5,542,407; 5,613,487; (Australia) 543790; 586383; (Canada) 1,123,296; 1,297,746; 2,195,264; (Mexico) 97-0457; (New Zealand) 200265; or other U.S. and foreign patents pending (ou autres brevets americains et etrangers en attente).

4072-166A

4 Outdoor Lifestyles • Villa Gas Owners/Installation Manual • 4072-170 • Rev Q • 08/18

B. Warranty

Outdoor Lifestyles by Hearth & Home Technologies™

Warranty

Hearth & Home Technologies (“HHT”) extends the following warranty for all Outdoor Lifestyles by HHT™ brand products (“Products”) that are purchased from an HHT authorized dealer.

WARRANTY COVERAGE:

HHT warrants to the original owner of the Product at the site of installation, and to any transferee taking ownership of the Product at the site of installation within one year following the date of original purchase, that the Product will be free from defects in materials and workmanship at the time of manufacture. After installation, if covered components manufactured by HHT are found to be defective in materials or workmanship during the applicable warranty period, HHT will, at its option, repair or replace the covered components. This warranty is subject to conditions, exclusions and limitations as described below.

WARRANTY PERIOD:

The warranty period runs for one year, beginning on the earlier of: (i) the date of invoice for the Product;

(ii) in the case of new home construction, the date of first occupancy of the residence or six months after the date of sale of the Product by an HHT authorized dealer, whichever occurs first; or (iii) the date 24 months following the date of Product shipment from HHT, regardless of the invoice or occupancy date.

WARRANTY CONDITIONS:

• This warranty only covers Products that are purchased through an HHT authorized dealer or distributor. A list of HHT authorized dealers is available on the HHT branded websites.

• This warranty is only valid while the Product remains at the site of original installation.

• Contact your installing dealer for warranty service. If the installing dealer is unable to provide necessary parts, contact the nearest HHT authorized dealer or supplier. Additional service fees may apply if you are seeking warranty service from a dealer other than the dealer from whom you originally purchased the Product.

• Check with your dealer in advance for any costs to you when arranging a warranty call. Travel and shipping charges for parts are not covered by this warranty.

WARRANTY EXCLUSIONS:

This warranty does not cover the following:

• Changes in surface finishes as a result of normal use. As a heating appliance, some changes in color of interior and exterior surface finishes may occur; this is not a flaw and not covered under warranty.

• Damage to printed, plated, or enameled surfaces caused by fingerprints, accidents, misuse, scratches, melted items, or other external sources and residues left on surfaces from the use of abrasive cleaners or polishes.

• Repair or replacement of parts that are subject to normal wear and tear during the warranty period. These parts include: paint, firebricks, grates, flame guides and the discoloration of glass.

• Minor expansion, contraction, or movement of certain parts causing noise. These conditions are normal and complaints related to this noise are not covered by this warranty.

Outdoor Lifestyles Warranty - 2108-975B - 2/15/13 - page 1

Outdoor Lifestyles • Villa Gas Owners/Installation Manual • 4072-170 • Rev Q • 08/18 5

• Damages resulting from: (1) failure to install, operate, or maintain the Product in accordance with the installation instructions, operating instructions, and listing agent identification label furnished with the Product; (2) failure to install the Product in accordance with local building codes; (3) shipping or improper handling; (4) improper operation, abuse, misuse, continued operation with damaged, corroded or failed components, accident, or incorrectly performed repairs; (5) inadequate ventilation, negative pressure or environmental conditions, including, without limitation: hail, snow, ice, fallen branches, flooding, water damage and fading of color; (6) use of fuels other than those specified in the operating instructions; (7) installation or use of components not supplied with the Product or any other components not expressly authorized and approved by

HHT; (8) modification of the Product not expressly authorized and approved by HHT in writing; and/or (9) interruptions or fluctuations of electrical power supply to the Product.

• Non-HHT venting components, hearth components or other accessories used in conjunction with the Product.

• Any part of a pre-existing fireplace system in which an insert or a decorative gas appliance is installed.

• The Product’s capability to heat the desired space. Information is provided to assist the consumer and the dealer in selecting the proper appliance for the application. Consideration must be given to the Product’s location and configuration and environmental conditions.

This warranty is void if:

• The Product has been over-fired or operated in atmospheres contaminated by chlorine, fluorine, or other damaging chemicals. Over-firing can be identified by, but not limited to, warped plates or tubes, rust colored cast iron, bubbling, cracking and discoloration of steel or enamel finishes and cracking or spalling of refractory or cementitious materials.

• The Product is subjected to prolonged periods of dampness, condensation, ice or snow.

• There is any damage to the Product or other components due to water or weather damage which is the result of, but not limited to, improper chimney or venting installation.

LIMITATIONS OF LIABILITY:

Repair or replacement in accordance with the provisions of this warranty will be the owner’s exclusive remedy for and will constitute HHT’s sole obligation under this warranty, under any other warranty

(express or implied), or in contract, tort or otherwise; provided, however, that if HHT is unable to provide repair or replacement in an expedient and cost effective manner, HHT may discharge all such obligations by refunding the purchase price of the Product. No employee, agent, dealer, or other person is authorized to give any warranty on behalf of HHT. TO THE EXTENT ALLOWED BY LAW, HHT MAKES NO OTHER

WARRANTY, EXPRESS OR IMPLIED, INCLUDING ANY WARRANTY OF MERCHANTABILITY OR

FITNESS FOR A PARTICULAR PURPOSE. HHT WILL NOT BE LIABLE FOR ANY CONSEQUENTIAL

OR INCIDENTAL DAMAGES ARISING OUT OF DEFECTS IN OR USE OF THE PRODUCTS. Some states do not allow exclusions or limitation of incidental or consequential damages, so these limitations may not apply to you. This warranty gives you specific rights; you also may have other rights, which vary from state to state. The duration of any implied warranty is limited to the duration of the warranty period specified herein.

Outdoor Lifestyles Warranty - 2108-975B - 2/15/13 - page 2

6 Outdoor Lifestyles • Villa Gas Owners/Installation Manual • 4072-170 • Rev Q • 08/18

2

Product Specific & Important Safety Information

A. Appliance Certification E. High Altitude Installations

MODELS: ODVILLAG-36T, ODVILLAG-36H,

ODVILLAG-42T, ODVILLAG-42H

LABORATORY: Underwriters Laboratories Inc. (UL)

TYPE: Outdoor Decorative Gas Appliance

STANDARD: ANSI Z21.97-2012/ CSA 2.41-2012

NOTICE: If the heating value of the gas has been reduced, these rules do not apply. Check with your local gas utility or authorities having jurisdiction.

This product is listed to ANSI standards for outdoor decorative gas appliances.

Outdoor Lifestyles is a registered trademark of Hearth &

Home Technologies.

When an appliance is for connection to a fixed piping system, the installation must conform with local codes, or in the absence of local codes with the National Fuel

Gas Code, ANSI Z223.1/NFPA 54, or International Fuel

Gas Code.

When installing above 2000 feet elevation:

• In the USA: Reduce input rate 4% for each 1000 feet above 2000 feet.

• In CANADA: Input ratings are certified without a reduction of input rate for elevations up to 4500 feet

(1370 m) above sea level. Please consult provincial and/ or local authorities having jurisdiction for installations at elevations above 4500 feet (1370 m).

Check with your local gas utility to determine proper orifice size.

B. BTU Specifications

This appliance is listed for use with the outdoor decorative hearth kit supplied.

Maximum allowable BTU ratings:

Unit

ODVILLAG-36

ODVILLAG-42

Max BTU/HR

40,000

42,000

WARNING: This product and the fuels used to operate this product (liquid propane or natural gas), and the products of combustion of such fuels, can expose you to chemicals including benzene, which is known to the State of California to cause cancer and reproductive harm. For more information go to: www.P65Warnings.

ca.gov.

C. Non-Combustible Materials

• Materials which will not ignite and burn, composed of any combination of the following:

- Steel

- Brick

- Concrete

- Glass

• Materials reported as passing ASTM E 136, Standard

Test Method for Behavior of Metals, in a Vertical Tube

Furnace at 750° C

- Iron

- Tile

- Slate

- Plasters

D. Combustible Materials

• Materials made of or surfaced with any of the following materials:

- Wood

- Plant fibers

- Compressed paper

- Plastic

- Plywood/OSB - Sheet rock (drywall)

• Any material that can ignite and burn; flame proofed or not, plastered or un-plastered

Outdoor Lifestyles • Villa Gas Owners/Installation Manual • 4072-170 • Rev Q • 08/18 7

3

Getting Started

A. Design and Installation Considerations

CAUTION

The appliance will not perform as an exterior wall. Moisture penetration must be considered for construction that places the appliance in structure walls or on moisture sensitive surfaces.

These appliances must be installed outdoors.

This outdoor gas appliance is designed for outdoor use. It may also be installed in screened porches and lanais that meet these minimum requirements:

• Minimum porch area: 96 sq. ft.

• Minimum ceiling height 84 in.

• Minimum of two walls must be screened.

• Minimum top of screen height, side walls: 6 ft. 8 in.

• Minimum screen area: 64 sq. ft.

Refer to Section 4.B. for clearances.

When installed on exterior walls: Hearth & Home

Technologies recommends that the appliance enclosure be constructed outside the structure’s weather envelope.

Where the platform meets the wall, use a flashing detail similar to that required for attached decks. Enclosure platforms, including hearths should slope away from the structure at 1/8 in. to 1/4 in. per foot. The appliance can be shimmed level.

Check building codes prior to installation.

When installed on surfaces where water may collect or cause damage: Hearth & Home Technologies recom mends that a drainage pan be placed under the unit. This can be constructed of metal, adhesive polymer membrane (such as ice and water shield) or other suitable materials. A means of drainage out of the pan such as tubes or weep holes should be provided. A slope of 1/8 in. to 1/4 in. per foot towards the drain port is suggested. The appliance can be shimmed level.

• Installation MUST comply with local, regional, state and national codes and regulations.

• Consult insurance carrier, local building, fire officials or authorities having jurisdiction about restrictions, installation inspection, and permits.

Installation MUST comply with local, regional, state and national codes and regulations. Consult the authorities having jurisdiction over restrictions, installation inspection and permits.

Hearths should slope away from the front of the appliance and enclosure at 1/8 in. to 1/4 in. per foot.

B. Inspect Appliance and Components

• Remove the appliance and components from the packaging and inspect for damage.

• Report any parts damaged in shipment to your dealer.

• Read all the instructions before starting the installation. Follow these instructions carefully during the installation to ensure maximum safety and benefit.

Before installing, determine the following:

• Where the appliance is to be installed.

- Clearance to side walls

- Location of indoor appliance terminations, air inlets, gas meters, etc.

- Doors

- Location of the fireplace to a door that swings open to ensure it does not interfere with the fireplace when opened

- Windows

- Walkways

- Wires

- Possibility of flooding or running water

• Gas supply piping requirements.

• Electrical wiring requirements.

WARNING! Risk of Fire or Explosion! Damaged parts could impair safe operation. DO NOT install damaged, incomplete or substitute components. Keep alliance dry.

Hearth & Home Technologies disclaims any responsibil ity for, and the warranty will be voided by, the following actions:

• Installation and use of any damaged appliance.

• Modification of the appliance.

• Installation other than as instructed by Hearth & Home

Technologies.

• Improper positioning of the gas logs.

• Installation and/or use of any component part not approved by Hearth & Home Technologies.

• Framing and finishing details.

Moisture Resistance

This outdoor gas appliance will shed moderate amounts of water, but is not waterproof. Water and condensing water vapor may enter the enclosure under certain conditions.

8

Any such action may cause a fire hazard.

WARNING! Risk of Fire or Explosion! DO NOT use this appliance if any part has been under water. Call a qualified service technician to inspect the appliance and to replace any part of the gas control system which has been under water.

Outdoor Lifestyles • Villa Gas Owners/Installation Manual • 4072-170 • Rev Q • 08/18

4

Framing and Clearances

A. Appliance Dimension Diagram

Dimensions are actual appliance dimensions. Use for reference only. For framing dimensions and clearances refer to Figures

4.2, 4.3, 4.4, 4.5, 4.6.

ODVILLAG-36

23 3/4 in.

603 mm

21 3/8 in.

543 mm

68°

39 1/2 in.

1003 mm

9 1/4 in.

235 mm

7 1/2 in.

191 mm

48 1/4 in.

1226 mm

GAS

KNOCKOUT

36 in.

914 mm

41 1/8 in.

1045 mm

7 5/8 in.

194 mm

19 3/4 in.

502 mm

20 7/8 in.

530 mm

7 5/8 in.

194 mm

7 1/2 in.

191 mm

9 1/4 in.

235 mm

GAS

KNOCKOUT

ODVILLAG-42

29 3/4 in.

756 mm

21 3/8 in.

543 mm

68°

39 1/2 in.

1003 mm

9 1/4 in.

235 mm

7 1/2 in.

191 mm

48 1/4 in.

1226 mm

GAS

KNOCKOUT

42 in.

1067 mm

47 1/8 in.

1197 mm

7 5/8 in.

194 mm

19 3/4 in.

502 mm

20 7/8 in.

530 mm

7 5/8 in.

194 mm

GAS

KNOCKOUT

7 1/2 in.

191 mm

9 1/4 in.

235 mm

Figure 4.1 Appliance Dimensions

Outdoor Lifestyles • Villa Gas Owners/Installation Manual • 4072-170 • Rev Q • 08/18 9

B. Clearances to Combustibles

When selecting a location for the appliance it is important to consider the required clearances to walls (see

Figure 4.2).

WARNING! Risk of Fire or Burns! Provide adequate clearance around air openings and for service access.

Due to high temperatures, the appliance should be located out of traffic and away from furniture and draperies.

NOTICE: Illustrations reflect typical installations and are

FOR DESIGN PURPOSES ONLY. Illustrations/diagrams are not drawn to scale. Actual installation may vary due to individual design preference.

Note: If this surface is inside the building’s warm air envelope...

...then this surface must be an exterior wall system.

D

E

D

D

B

D

D C

D

A

D

ODVILLAG-36

ODVILLAG-42 in.

mm in.

mm

A

67 7/8

1724

73 7/8

1876

B

21 1/2

546

21 1/2

546

C

42

1067

48

1219

D

1/2

13

1/2

13

E

48

1219

52 1/4

1327

Figure 4.2 Appliance Locations

10 Outdoor Lifestyles • Villa Gas Owners/Installation Manual • 4072-170 • Rev Q • 08/18

B

Framing Dimensions

ODVILLAG-36

ODVILLAG-42 in.

mm in.

mm

A

21 1/2

546

21 1/2

546

Use only noncombustible material below the top of the top standoffs.

B

39 3/4

1010

39 3/4

1010

C

42

1067

48

1219

C

Upper front can be covered with non-combustible material or removed and replaced with non-combustible material.

A

1/2 in. (13 mm)

0 in. to level of standoffs

84 in.

(2134 mm) to ceiling

0 in.

Combustible flooring may be installed next to the front of the appliance.

1/2 in.

(13 mm)

1/2 in. (13 mm)

Combustible facing

0 in.

36 in.

(914 mm)

Figure 4.3 Framing Dimensions

Outdoor Lifestyles • Villa Gas Owners/Installation Manual • 4072-170 • Rev Q • 08/18 11

C. Vent Termination Minimum Clearances

D

E

A

FP

G

H

R

O

P

FP

N

Q

(See Note 2)

Alcove

L

B

FP

B

F

FP

FP

B

I

M

FP X

J or K

= AREA WHERE FIREPLACE IS NOT PERMITTED FP = FIREPLACE OPENING X = AIR SUPP LY INLET

I

A = 0 in. . . . . . . . . . clearances above grade, veranda, porch, deck or balcony.

B = 12 in. . . . . . . . . . clearances to window or door that may be opened, or to permanently closed window.

20 in. . . . . . . . . . vinyl windows or siding.

D = 47 in. . . . . . . . . . vertical clearance to unventilated soffit or to ventilated soffit located above the terminal.

60 in. . . . . . . . . . vinyl clad soffits.

F = 9 in. . . . . . . . . . clearance to outside corner.

G* = 12 in. . . . . . . . . . clearance to inside corner, non-vinyl siding.

H = 3 ft. (Canada) . not to be installed above a gas meter/regulator assembly within

3 ft (914 mm) horizontally from the center line of the regulator.

= 3 ft. (USA)

6 ft. (Canada) . clearance to service regulator vent outlet and electric service.

* 48 in. minimum for vinyl windows or vinyl siding.

** only permitted if veranda, porch, deck or balcony is fully open on a minimum of 2 sides beneath the floor, or if the screened porch guidelines are followed.

Note 1: Local codes or regulations may require different clearances.

Note 2: Appliance in an alcove space (spaces open only on one side and with an overhang) are permitted with the dimensions specified for vinyl or non-vinyl siding and soffits. 1) There must be a 3 ft minimum between terminations or between the fireplace and termination. 2) All mechanical air intakes within 10 ft of a termination must be a minimum of 3 ft below the fireplace hood. 3) All gravity air intakes within 3 ft of the fireplace opening must be a minimum of 1 ft below the termination.

Figure 4.4 Minimum Clearances

J = 9 in. (USA)

12 in. (Canada) . clearance to non-mechanical air supply inlet to building or the combustion air inlet to any other appliance.

K = 3 ft. (USA)

6 ft. (Canada) . clearance to a mechanical air supply inlet.

L = . . . . . . . . . . (See note 4)

M** = 47 in. . . . . . . . . . clearance under veranda, porch, deck, balcony or overhang.

Not allowed: . . . . . . vinyl

N* = 12 in. . . . . . . . . . clearance to inside corner, non-vinyl siding. (Alcove)

O = 47 in.

P = 84 in.

Q

MIN

R

MAX

VillaGas 10 feet 2 x Q

1 additional termination cap Q + 3 feet 1 x Q

2 additional termination caps Q + 6 feet 2/3 x Q

3 additional termination caps Q + 9 feet 1/2 x Q

ACTUAL

R

MAX

= (2 / # caps plus fireplace ) x Q

ACTUAL

This fireplace is approved for installation onto screen porches with the following guidelines:

Minimum porch area: 96 sq ft

Minimum ceiling height: 84 in.

Minimum of two walls must be screened

Minimum top of screen height, side walls: 80 in.

Minimum screen area: 64 sq ft

Note 3: There may be some odor and small amounts of soot associated with burning outdoor gas fireplaces on a screened porch. Consider prevailing wind direction for best flame performance.

Note 4: For appliances installed facing or opening onto public property or property servicing more than one single family dwelling, such as driveways, sidewalks, etc. refer to local building codes/regulations for proper clearances.

12 Outdoor Lifestyles • Villa Gas Owners/Installation Manual • 4072-170 • Rev Q • 08/18

D. Constructing the Appliance Enclosure

NOTICE: Install appliance on hard metal or wood surfaces extending full width and depth. DO NOT install directly on carpeting, vinyl, tile or any combustible material other than wood.

WARNING! Risk of Fire! Maintain specified air space clearances to appliance.

• Insulation and other materials must be secured to prevent accidental contact.

• The enclosure must be properly blocked to prevent combustibles from entering and making contact with fireplace.

• Failure to maintain airspace may cause overheating and a fire.

E. Securing and Leveling the Appliance

WARNING! Risk of Fire! Prevent contact with:

• Sagging or loose insulation

• Insulation backing or plastic

• Framing and other combustible materials

NAILING TABS

(BOTH SIDES)

Figure 4.5 Proper Positioning and Securing of an Appliance

DO NOT notch the framing around the appliance standoffs.

Failure to maintain air space clearance may cause overheating and fire.

F. Non-Combustible Material Installation

Combustible

Framing

Combustible

Facing

12 in.

Noncombustible

Facing

The diagram shows how to properly position and secure the appliance (see Figure 4.4). Nailing tabs are provided to secure the appliance to the framing members.

• Bend out nailing tabs on each side.

• Place the appliance into position.

• Keep nailing tabs flush with the framing.

• Level the appliance from side to side and front to back.

• Shim the appliance as necessary. It is acceptable to use wood shims underneath the appliance.

• Secure the appliance to the framing by using nails or screws through the nailing tabs.

• Secure the appliance to the floor by inserting two screws through the pilot holes at the bottom of the appliance.

Figure 4.6 Noncombustible Material Installation

• A 12 in. noncombustible facing material (supplied) is required off the top of the appliance. Above 12 in., a combustible facing material is acceptable.

• Combustible framing can be installed above appliance top standoffs, behind the 12 in. noncombustible facing.

Outdoor Lifestyles • Villa Gas Owners/Installation Manual • 4072-170 • Rev Q • 08/18 13

5

Gas Information

A. Fuel Conversion

• Make sure the appliance is compatible with available gas types.

• Conversions must be made by a qualified service technician using Hearth & Home Technologies specified and approved parts.

B. Gas Pressure

Refer to instructions provided with hearth kit (4072-179).

WARNING! Risk of Fire or Explosion! High pressure will damage valve. Low pressure may cause explosion.

• Verify inlet pressures. Verify minimum pressures when other household gas appliances are operating.

• Install regulator upstream of valve if line pressure is greater than 1/2 psig (14 in. w.c.).

WARNING

Fire Risk.

Explosion Hazard.

High pressure will damage valve.

• Disconnect gas supply piping BEFORE pressure testing gas line at test pressures above 1/2 psig.

• Close the manual shutoff valve BEFORE pressure testing gas line at test pressures equal to or less than 1/2 psig.

C. Gas Connections Provision

WARNING! Fire and/or Asphyxiation Risk! Use with outdoor decorative appliance only. Not for use with solid fuel.

The certified outdoor decorative hearth kit (supplied) must be installed in this fireplace.

• Knockouts are provided on both sides of the fireplace and in refractories for 1/2 in. (13 mm) iron pipe.

• Seal refractory around pipe with fireplace mortar or a non-combustible sealant.

NOTE: Hearth & Home Technologies recommends when installing rigid gas pipe in the Villa Gas appliance that an accessible pipe joint (not a union) be provided inside of the firebox to aid in replacement of the appliance hearth refractory, should it become necessary.

Firebox

Refractory

Seal with fireplace mortar or non-combustible sealant

Outer shell of fireplace

Maintain air clearance to combustibles.

Combustible materials

When an appliance is for connection to a fixed piping system, the installation must conform with local codes, or in the absence of local codes with the National Fuel

Gas Code, ANSI Z223.1/NFPA 54, or International Fuel

Gas Code.

Gas line Gas line

Repack insulation knockout

Figure 5.1 Gas Line Installation

14 Outdoor Lifestyles • Villa Gas Owners/Installation Manual • 4072-170 • Rev Q • 08/18

D. High Altitude Installations

NOTICE: If the heating value of the gas has been reduced, these rules do not apply. Check with your local gas utility or authorities having jurisdiction.

When installing above 2000 feet elevation:

• In the USA: Reduce input rate 4% for each 1000 feet above 2000 feet.

• In CANADA: Input ratings are certified without a reduction of input rate for elevations up to 4500 feet (1370 m) above sea level. Please consult provincial and/or local authorities having jurisdiction for installations at elevations above 4500 feet (1370 m).

Check with your local gas utility to determine proper orifice size.

E. Air Shutter Setting

Refer to instructions provided with hearth kit (4072-179).

Outdoor Lifestyles • Villa Gas Owners/Installation Manual • 4072-170 • Rev Q • 08/18 15

6

Finishing

A. Facing Material

• The Villa Gas appliance requires the front of the appliance to be covered with noncombustible material

(e.g.: stone, marble, tile, etc.) A maximum of one (1) inch of exposed metal on all sides is permitted.

• Facing and/or finishing materials must not interfere with air flow through louvers, operation of louvers or doors, or access for service.

• Facing and/or finishing materials must never overhang into the appliance opening.

• Observe all clearances when applying combustible materials.

• Seal joints between the finished wall and appliance top and sides using a 300º F minimum sealant. Refer to

Figure 6.1.

WARNING! Risk of Fire! DO NOT apply combustible materials beyond the minimum clearances. Comply with all minimum clearances to combustibles as specified in this manual. Overlapping materials could ignite and will interfere with proper operation of doors and louvers.

1 in. Maximum

( All sides)

CAUTION: This fireplace requires the front of the appliance to be covered with a noncombustible material

(e.g. stone, marble, tile, etc.). A maximum of 1 in. of exposed metal on all sides is permitted.

Figure 6.2 Non-combustible Material

Finish wall material may be combustible - Top and Sides

0 in.

12 in. noncombustible material (required)

0 in.

0 in.

High Temperature Sealant (300° F/149° C min.)

Top and Side Seal Joint

Figure 6.1 Non-combustible Facing Diagram

16 Outdoor Lifestyles • Villa Gas Owners/Installation Manual • 4072-170 • Rev Q • 08/18

B. Mantel and Wall Projections

WARNING! Risk of Fire! Comply with all minimum clearances as specified. Framing closer than the minimums listed must be constructed entirely of non-combustible materials

(i.e., steel studs, concrete board, etc.).

Mantels

1

2

3

4

5

6

7

8

9

10

11

12

13

14

15

16

17

18

84 in. minimum floor to ceiling

A B C D E F G H I J K L M N O P Q R

Measured from top of hood (in inches)

Floor

A B C D E F G H I J K L M N O P Q R

Combustible in.

16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 mm 406 432 457 483 508 533 559 584 610 635 660 686 711 737 762 787 813 838

Noncombustible in.

mm

0

0

18 19 20 21 22 23 24 25 26 27 28 29

457 483 508 533 559 584 610 635 660 686 711 737

Figure 6.3 Minimum Vertical and Maximum Horizontal Dimensions of Combustibles

Outdoor Lifestyles • Villa Gas Owners/Installation Manual • 4072-170 • Rev Q • 08/18 17

Mantel Legs or Wall Projections

Combustible

Facing Material

A

B

Mantel leg or perpendicular wall

Combustible

A 12 IN. (305 MM) MIN.

TO PERPENDICULAR WALL

B 14-1/2 IN. (368 MM) MIN.

FROM FIREPLACE OPENING

TO PERPENDICULAR WALL

Noncombustible

A 6 IN. (152 MM) MIN.

TO PERPENDICULAR WALL

B 8-1/2 IN. (216 MM) MIN.

FROM FIREPLACE OPENING

TO PERPENDICULAR WALL

Figure 6.4 Mantel Leg or Wall Projections (Acceptable on both sides of opening)

18 Outdoor Lifestyles • Villa Gas Owners/Installation Manual • 4072-170 • Rev Q • 08/18

7

Appliance Setup

A. Remove the Shipping Materials

Remove hearth kit (2 boxes) from inside the firebox.

B. Clean the Appliance

Clean/vacuum any sawdust that may have accumulated inside the firebox.

C. Install Hood

• Loosen six screws located on bottom edge of upper face.

• Slide hood into position.

• Tighten six screws previously loosened.

D. Install Hearth Kit (provided)

Refer to instructions provided with hearth kit (4072-179).

E. Install Mesh Door (optional)

Refer to instructions provided with mesh doors.

WARNING! Risk of Fire! Install ONLY doors or fronts approved by Hearth & Home Technologies. Unapproved doors or fronts may cause fireplace to overheat.

Figure 7.1 Install Hood

Outdoor Lifestyles • Villa Gas Owners/Installation Manual • 4072-170 • Rev Q • 08/18 19

8

Maintenance and Service

• Refer to installation instructions provided with the hearth kit (4072-179).

• Any guard or other protective device removed for servicing the appliance must be replaced prior to operating the appliance.

• Installation and repair should be done by a qualified service person. The appliance should be inspected before use and at least annually by a qualified service person. More frequent cleaning may be required as necessary. It is imperative that control compartment, burners, and circulating air passageways of the appliance be kept clean.

20 Outdoor Lifestyles • Villa Gas Owners/Installation Manual • 4072-170 • Rev Q • 08/18

B. Accessories

Mesh Doors

DSVILLA36

DSVILLA42

Outdoor Lifestyles • Villa Gas Owners/Installation Manual • 4072-170 • Rev Q • 08/18 25

C. Contact Information

Hearth & Home Technologies

7571 215th Street West

Lakeville, MN 55044 www.hearthnhome.com

Please contact your Outdoor Lifestyles dealer with any questions or concerns.

For the number of your nearest Outdoor Lifestyles dealer, please visit www.hearthnhome.com.

– NOTES –

NOTICE

• Important operating and maintenance instructions included.

DO NOT DISCARD THIS MANUAL

• Read, understand and follow these instructions for safe installation and operation.

• Leave this manual with party responsible for use and operation.

26

This product may be covered by one or more of the following patents: (United States) 5613487, 5647340, 5890485,

5941237, 6006743, 6019099, 6053165, 6145502, 6374822, 6484712, 6601579, 6769426, 6863064, 7077122, 7098269,

7258116, 7470729, 8147240 or other U.S. and foreign patents pending.

2000-945C

Printed in U.S.A. - Copyright 2013

Outdoor Lifestyles • Villa Gas Owners/Installation Manual • 4072-170 • Rev Q • 08/18

advertisement

Related manuals

Download PDF

advertisement