- No category
advertisement
Korenix JetCard Series Multiport Serial
Card/Ethernet Switch Card
User’s Manual
Version V1.3, Jan. 2010
www.korenix.com
Korenix JetCard Series Multiport Serial
Card/Ethernet Switch Card
User’s Manual
Copyright Notice
Copyright
© 2008 Korenix Technology Co., Ltd.
All rights reserved.
Reproduction in any form or by any means without permission is prohibited.
Table of Contents
Chapter 1
1
Introduction
Welcome to Korenix JetCard Series Multiport Serial Card/Ethernet Switch Card. Korenix JetCard
Series Multiport Serial Card/Ethernet Switch Card is a high performance Universal PCI/PCI-104 card. JetCard Series can bring you high-speed and high-quality serial communication service.
The following topics are covered in this chapter:
Overview
Product Features
Package Checklist
Installation Guide
Overview
Korenix JetCard Series Multiport Serial Card/Ethernet Switch Card is a high performance
Universal PCI/PCI-104 card. JetCard Series can bring you high-speed and high-quality serial communication service.
JetCard Switch Series uses Marvell 88E6065 chip to provide 5 Ethernet ports. Each Ethernet port in the JetCard Switch Series offers IEEE 802.3 10 Base-T and 100 Base-Tx compliant
Ethernet data transmission with auto MDI/MDI-X and auto- negotiation.
JetCard Multiport Series products use high-integrated Oxford chipset, which provides up to
921.6 kbps data transmission speed. JetCard Multiport Series products also come with 128-byte
FIFO, which allows JetCard Multiport Series to occupy the least system resources even when operating with full speed and full loading.
In order to cope with harsh industrial environments, Korenix engineers select high quality components, ensuring that JetCard can still operate efficiently and stably under extremely high/low temperature. JetCard is also equipped with built-in surge protection and optical isolation, greatly prevent JetCard and your serial devices from noise or sudden electric surge often exist in industrial environments. For this reason, JetCard products can provide you with stable and reliable communications under any harsh environment.
No matter what your application is, JetCard is the ideal choice for your systems, bringing you the most reliable and cost-effective solution.
JetCard Product Family (Universal PCI Card)
Model Name
JetCard JetCard JetCard
1208L 1208/1208w 1204/1204w
JetCard JetCard JetCard JetCard
1402 1402i 1404 1404i
JetCard
2205/2205w
Ports 2 2 4 4
10/100Mbps
Ethernet
128 Bytes FIFO
●
921.6 Kbps Speed
●
Surge Protection
●
●
●
●
Optical Isolation
VHDCI DB62
Board Connector
68 Female
JetCard Product Family (PCI-104 Card)
●
●
●
DB37
Female
●
●
●
●
●
●
●
●
●
●
●
●
●
●
5
●
●
●
DB9
Male * 2
DB9
Male * 2
DB37
Female
DB37
Female
RJ45
Model Name
RS-232 Ports
RS-422/485 Ports
10/100Mbps Ethernet
128 Bytes FIFO
921.6 Kbps Speed
Surge Protection
Optical Isolation
Board Connector
1-2 Korenix JetCard Series User’s Manual
JetCard 2105/2105w JetCard 1608/1608w
8 or 4
4
5
●
●
●
●
●
●
RJ45 DB37 Female
Product Features
Korenix JetCard Series products have the following features:
IEEE 802.3 10/100 Base-Tx compatible (JetCard 2105/2205)
IEEE 802.1Q tag VLAN/QoS supported (JetCard 2105/2205)
High Performance UPCI/PCI-104 Multiport Serial Card/ Ethernet Switch Card
High Speed Up to 921.6 Kbps
2 KV optical isolation (1402i/1404i)
Introduction
Built-In Termination Resistors (RS-422/485)
Automatic Hardware Flow Control for 2-wire RS-485
Plug and Play for Easy Installation
Wide Operating Temperature: -10 to 70℃,-40 to 80℃
(JetCard 1204w, JetCard 1208w, JetCard 2105w, JetCard 2205w, JetCard 1608w)
Korenix JetCard Utility (JetCard 1204/1208/1404/1402 Series)
Universal PCI Low Profile Card (JetCard 1208L)
Package Checklist
Korenix JetCard Series products are shipped with the following items:
JetCard Serial Card
Documentation and Software CD
Quick Installation Guide
Screw Pack (JetCard 2105/JetCard 1608)
Standard Bracket (JetCard 1208L)
If any of the above items is missing or damaged, please contact your local sales representative.
Installation Guide
JetCard Series products are easy to install and use. Please follow the steps below to test your
JetCard.
Korenix JetCard Series User’s Manual 1-3
1-4 Korenix JetCard Series User’s Manual
Chapter 2
2
Hardware Installation
This chapter includes information about how to install your JetCard.
The following topics are covered in this chapter:
Introduction
Panel Layout
DIP Switch and Jumper Settings
Installing Your JetCard
Removing Your JetCard
Introduction
2-2 Korenix JetCard Series User’s Manual
Panel Layout
JetCard 1208L
JetCard 1204/1204w
Hardware Installation
JetCard 1208/1208w
JetCard 1402 JetCard 1402i
JetCard 1404 JetCard 1404i
Korenix JetCard Series User’s Manual 2-3
JetCard 2205/2205w
JetCard 2105/2105w JetCard 1608/1608w
2-4 Korenix JetCard Series User’s Manual
Dimensions (Unit-mm)
JetCard 2105/2105w
Hardware Installation
JetCard 1608/1608w
Korenix JetCard Series User’s Manual 2-5
(Unit-mm)
JetCard 2205/2205w
2-6 Korenix JetCard Series User’s Manual
JetCard 1208L
Hardware Installation
JetCard 1208/1208w
Korenix JetCard Series User’s Manual 2-7
JetCard 1204/1204w
JetCard 2205/2205w/1204/1204w/1208/1208w
2-8 Korenix JetCard Series User’s Manual
(Unit-mm)
JetCard 1404/1404i
Hardware Installation
JetCard 1402/1402i
Korenix JetCard Series User’s Manual 2-9
Connecter
JetCard 2105/2105w
JetCard 1608/1608w
2-10 Korenix JetCard Series User’s Manual
Hardware Installation
DIP Switch and Jumper Settings
Before you start using JetCard RS-422/485 products (JetCard 1402, JetCard 1402i, JetCard
1404, JetCard 1404i and JetCard 1608), configure the DIP Switch and Jumper settings of each port. DIP Switch can configure RS-422, 4-wire RS-485, or 2-wire RS-485. JetCard 1400 Series jumper can be used to configure JetCard’ built-in Termination Resistors
Before you start using JetCard Switch Series products (JetCard 2105, JetCard 2205), configure the Jumper of each. Jumper can configure ID select.
RS-422 without Termination RS-422 with Termination
4-wire RS-485 without Termination 4-wire RS-485 with Termination
2-wire RS-485 without Termination 2-wire RS-485 with Termination
Korenix JetCard Series User’s Manual 2-11
DIP Switch and Jumper Settings
JetCard 2205 Jumper1 interrupt Select for ID Select Setting. Use Jumper1 (JP1) short 1-2, 3-4, 5-6 or 7-8 to ID select. The default select is 1-2.
Jumper Short Indication
(Default)
JetCard 2105 Jumper1-5 PCI Routing Select for ID Select Setting. Use Jumper1-5 (JP1-5) short 1-2,
3-4, 5-6 or 7-8 to ID select. The default select is 1-2.
Jumper Short Indication
JP3
JP4
JP5
(Default)
JetCard 2105/2205 LED Indicators
LED Color Indication
Full Duplex Yellow
Half Duplex
ON
Yellow OFF
Collision
Yellow
Blinking: Collision activity
(blinking rate is 84ms active)
2-12 Korenix JetCard Series User’s Manual
Hardware Installation
JetCard 1608 DIP Switch
Select the Serial Interface (RS-232/422/485) for Com1.
RS-232 (Default)
COM1 (SW1) OFF ON
RS-422
OFF OFF ON ON ON ON
COM2 (SW2)
COM3 (SW3)
COM4 (SW4)
OFF ON OFF OFF ON ON ON ON
OFF ON OFF OFF ON ON ON ON
OFF ON OFF OFF ON ON ON ON
RS-485/2W
RS-485/4W
COM1 (SW1)
COM2 (SW2)
COM3 (SW3)
COM4 (SW4)
ON
ON
OFF
OFF
Korenix JetCard Series User’s Manual 2-13
JetCard 1608 Jumper 1-4 for PCI Clock, ID Select and Interrupt Select Setting.
Jumper Short (Default)
Indication
JP1 1-3
JP2 1-3
JP3
JP4
(Default)
Jumper Short
JP1 4-6
JP2 2-4
JP3
JP4
Indication
Jumper Short
JP1 4-6
JP2 4-6
JP3
JP4
Indication
Jumper Short
JP1 3-5
JP2 3-5
JP3
JP4
Indication
2-14 Korenix JetCard Series User’s Manual
Installing Your JetCard
Follow the steps below to install your JetCard.
1. Power off the PC.
2. Remove the PC case.
3. Remove the slot cover.
4. Insert the JetCard into the PCI/PCI-104 card.
5. Tighten the JetCard with screws.
6. Place the PC case back.
Hardware Installation
For JetCard 2105, JetCard 1608 PCI-104 card
The PCI-104 form factor supports the PCI bus. The maximum configuration for the PCI bus of PCI-104 modules is four plus the Host Board.
Korenix JetCard Series User’s Manual 2-15
Removing Your JetCard
1. Power off the PC.
2. Remove the PC case.
3. Remove the screws from the JetCard.
5. Place the PC case back.
2-16 Korenix JetCard Series User’s Manual
Chapter 3
3
Software Installation
This chapter includes information about installation and configuration.
The following topics are covered in this chapter:
Windows
Linux
Windows
Korenix JetCard Series products support Windows 2003 / XP/2000/98/ME/NT OS. Follow the steps below to install the driver and configure COM ports.
Windows XP/2003
Installing the Driver for JetCard 2105/2205
Follow the hardware installation instructions in the previous chapter to install the JetCard 2105/2205 first.
Windows XP/2003 will automatically detect the new JetCard 2105/2205 after you power on your PC.
1. Found new hardward
2. Insert the JetCard software CD into the CD-ROM.
3. Select Hardware tab, and click on the Device Manager button.
4. Click on the Properties button
3-2 Korenix JetCard Series User’s Manual
Software Installation
5. Click on the Update Driver button
6. In the Found New Hardware Wizard window, select No, not this time, and click on Next to continue.
Sometimes, this window might not appear. It depends on your Windows XP/2003 version.
7. In the window to open next, select Install from a list or specific location (Advanced), and click on Next to continue.
Korenix JetCard Series User’s Manual 3-3
8. In the window that opens next, select Search for the best driver in these locations, and check Include
this location in the search. Click on Next to start installing the driver.
3-4 Korenix JetCard Series User’s Manual
9. C:JetCard CD V1.4\jetcard_2105_2205_driver\Netrtls.inf
Software Installation
Korenix JetCard Series User’s Manual 3-5
3-6 Korenix JetCard Series User’s Manual
Software Installation
10. A Completing the Found New Hardware Wizard window will open when the driver installation is complete.
Click on Finish to leave the installation window.
Korenix JetCard Series User’s Manual 3-7
Installing the Driver for JetCard 1200/1400/1600 Series
1. Follow the hardware installation instructions in the previous chapter to install the JetCard first.
Windows XP/2003 will automatically detect the new JetCard after you power on your PC.
2. Insert the JetCard software CD into the CD-ROM. continue. Sometimes, this window might not appear. It depends on your Windows XP/2003 version.
4. In the window to open next, select Install from a list or specific location (Advanced), and click on Next to continue.
3-8 Korenix JetCard Series User’s Manual
Software Installation
5. In the window that opens next, select Search for the best driver in these locations, and check Include this location in the search. Click on Next to start installing the driver.
6. The window to open next will show you that wizard starts installing the driver. In the window that prompts next, click on Continue Anyway to proceed the driver installation.
Korenix JetCard Series User’s Manual 3-9
7. A the Found New Hardware Wizard window will open when the driver installation is complete. Click on Finish to leave the installation window.
8. Next, you need to install JetCard Auxiliary Function and COM ports. The steps for installing
COM ports are almost the same. Follow the windows instructions and repeat several times until each COM port is installed.
How to Check the Installation
After the driver installation is complete, follow the steps below to check if the installation is successful. on
ÆControl PanelÆSystem.
3-10 Korenix JetCard Series User’s Manual
Software Installation
Korenix JetCard Series User’s Manual 3-11
port number depends on which JetCard model you installed. In this case, 4 COM ports of
JetCard 1204/1204w were installed.
COM Port Configuration
This section includes information of how to configure COM ports. on
ÆSettingsÆControl Panel ÆSystemÆHardwareÆDevice Manager. And then double click on the COM port you wish to configure.
3-12 Korenix JetCard Series User’s Manual
Software Installation you wish to reconfigure COM port mapping, click on Advanced…button.
For JetCard 1608
Korenix JetCard Series User’s Manual 3-13
levels and XON/XOFF Flow Control threshold.
3-14 Korenix JetCard Series User’s Manual
Software Installation
Removing the Driver
Click on Start
ÆSettingsÆControl Panel ÆSystemÆHardwareÆDevice Manager. Select the
JetCard and Auxiliary Function, and click on the Uninstall icon located in the tool bar.
Korenix JetCard Series User’s Manual 3-15
Windows 2000
Installing the driver
1. Follow the hardware installation instructions in the previous chapter to install the JetCard first.
Windows 2000 will automatically detect the new JetCard after you power on your PC.
2. Insert the JetCard software CD into the CD-ROM.
3. The window to open next indicates that the Hardware Wizard found the new hardware. Click on Next to install. continue.
3-16 Korenix JetCard Series User’s Manual
Software Installation
7. The window that opens next shows the driver files search results. Click on Next to continue.
Korenix JetCard Series User’s Manual 3-17
9. After the driver installation is complete, click on Finish to leave the installation window.
10. Next, you need to install JetCard Auxiliary Function and COM ports. The steps for installing
COM ports are almost the same. Follow the windows instructions and repeat several times until each COM port is installed.
How to Check the Installation
Follow the instructions in How to Check the Installation section in Windows XP/2003.
COM Port Configuration
Follow the instructions in COM Port Configuration section in Windows XP/2003.
Removing the Driver
Follow the instructions in Removing the Driver section in Windows XP/2003.
3-18 Korenix JetCard Series User’s Manual
Software Installation
Windows 98/ME
Installing the Driver
1. Follow the hardware installation instructions in the previous chapter to install the JetCard first.
Windows 98/ME will automatically detect the new JetCard after you power on your PC.
2. Insert the JetCard software CD into the CD-ROM.
Windows 98
3. The window to open next indicates that the Hardware Wizard found the new hardware. Click on Next to install.
Windows ME
3. Select Specify the location of the driver
(Advanced). Click on Next to install.
Windows 98
4. Select Display a list of all the drivers in
a specific location, so you can select
the driver you want, and click on Next to continue.
Windows ME
4. Select Display a list of all the drivers in
a specific location, so you can select
the driver you want, and click on Next to continue.
Korenix JetCard Series User’s Manual 3-19
7. Locate the driver file on the CD, and click on OK to continue.
3-20 Korenix JetCard Series User’s Manual
Software Installation
10. After the driver installation is complete, click on Finish to leave the installation window.
11. Next, Windows 98/ME will start to install COM ports automatically. Sit back and wait for the
COM port installation to finish.
Korenix JetCard Series User’s Manual 3-21
How to Check the Installation
Follow the instructions in How to Check the Installation section in Windows XP/2003.
COM Port Configuration
Follow the instructions in COM Port Configuration section in Windows XP/2003.
Removing the Driver
Follow the instructions in Removing the Driver section in Windows XP/2003.
Windows NT
Installing the Driver
1. Insert the JetCard software CD into the CD-ROM.
KXInstaller icon to start the driver installation.
3. Click on Next to continue.
4. In the window to open next, select INSTALL, and in the License Agreement window, click on Yes to agree to the terms.
3-22 Korenix JetCard Series User’s Manual
Software Installation
5. After the driver installation is complete, click on Exit to leave the installation window.
How to Check the Installation
on
ÆSettingsÆControl Panel.
2. Double clicks on the Devices icon.
Korenix JetCard Series User’s Manual 3-23
3. Windows NT Devices List will open next. Check if Korenix PCI Serial Driver is in the list.
Click on Close to close the window.
4. The next step is to check COM ports installation. Double click on Ports icon in Control
Panel.
5. The COM Ports list will open next. Check if the COM Ports are all successfully installed.
Click on Cancel to close the window.
Removing the Driver
1. Repeat step 1 to 3 of Installing the Driver in Windows NT.
3. Click on Exit to leave the uninstallation window.
3-24 Korenix JetCard Series User’s Manual
Software Installation
Linux
Installing the Linux Driver
Note: use root as the username to log in.
Note: mount your CD device and insert Korenix JetCard CD first.
1. Copy the driver file to the hard disk and decompress.
# mkdir korenix
# cp /mnt/cdrom/jetcard_driver/linux/jetcarddrv.tgz korenix
# cd korenix
# tar xfz jetcarddrv.tgz
2. Compile the driver file.
# cd jetcarddrv
# make
3. Create the device files.
# ./mknod.jetcard
4. Now the JetCard driver is installed correctly. JetCard driver will be loaded into your system automatically during the next boot up. Or you could start to load the driver manually right now with the command below:
#/etc/init.d/jetcard start
Testing JetCard Under Linux
Korenix provides a test program “rstest” for testing your JetCard under Linux. Before you start to test, finish the JetCard hardware and driver installation.
“rstest” program can test to see if two serial ports communicate with each other. You need to connect two serial ports’ TX, RX, RTS, and CTS for testing (“rstest” uses hardware handshaking mode). The test procedures are described below:
1. You need to compile the test program if you are using “rstest” for the first time.
#cd /……/korenix/jetcarddrv/rstest
#make
2. The commands of the test program are as follows:
#./rstest [-d] [-m] [-s n] </dev/ttyJn1> </dev/ttyJn2>
[-d] disable RX/TX transfer test
[-m] enable modem control line test
[-s n] The highest test baud rate n = 9, baud rate = 230K n = 10, baud rate = 460K n = 11, baud rate = 921K
For Example:
Ex1. Test to see if ttyJ0 and ttyJ1 communicate with each other with baud rate up to 921 Kbps.
# ./rstest –s 11 /dev/ttyJ0 /dev/ttyJ1
Ex2. Test to see the modem line status of ttyJ0 and ttyJ1.
# ./rstest –d –m /dev/ttyJ0 /dev/ttyJ1
Korenix JetCard Series User’s Manual 3-25
Chapter 4
4
Korenix JetCard Utility
This chapter includes information about how to use Korenix JetCard Utility to test and diagnose your JetCard (except JetCard 2205/2105/1608)
The following topics are covered in this chapter:
Installing Korenix JetCard Utility
Using Korenix JetCard Utility
Uninstalling Korenix JetCard Utility
After you finish JetCard’s hardware and software installation, you can use the provided Korenix
JetCard Utility to test functions of your communication system.
Installing Korenix JetCard Utility
Note: Korenix JetCard Utility can be operated under Windows 2003/XP/2000/ME/98.
1. Insert the JetCard software CD into the CD-ROM. Locate the setup file in jetcard_utility folder.
4-2 Korenix JetCard Series User’s Manual
Korenix JetCard Utility continue. requirements. Click on Next to continue.
6. The setup program will ask you to select the destination where you wish to install the Korenix
JetCard Utility. Click on Next to continue.
Korenix JetCard Series User’s Manual 4-3
7. The window to open next will ask you where you wish to place the JetCard Utility in the Start
Menu. Click on Next to continue.
8. The window to open next will ask if you wish to create a desktop icon. Check the Create a
desktop icon box if you wish to have a JetCard Utility icon on your desktop. Click on Next to continue.
4-4 Korenix JetCard Series User’s Manual
Korenix JetCard Utility
9. The window to open next will allow you to confirm whether all of the settings are correct. If you wish to make changes, click on Back to do so. If the settings are correct, click on Install to start the installation process.
10. The JetCard Utility installation is complete. If you wish to start up the utility right away, check the Launch Korenix JetCard Diagnostic box and click on Finish. Otherwise uncheck the
Launch Korenix JetCard Utility box, and click on Finish to leave the installation window.
Using Korenix JetCard Utility
Korenix JetCard Utility comprises of JetCard Diagnostic Internal Test and External Test. The
Internal Test of the JetCard Diagnostic Test can allow you to check JetCard’s status, while the
External Test can allow you to check if the pins and cables needed for communications are functioning normally (please use loop back circuit for your test environment).
JetCard Diagnostic Test
1. Double click on JetCard Utility Icon to launch the program.
2. The JetCard Utility will automatically detect how many JetCards are installed in your PC.
Korenix JetCard Series User’s Manual 4-5
on
ÆConfig to open the Diagnostic window. Click on Communication
Parameters tag to set up serial communication basic parameters. to check JetCard’s status, while the External Test can allow you to check if the pins and cables needed for communications are functioning normally (please use loop back circuit for your test environment).
4-6 Korenix JetCard Series User’s Manual
Korenix JetCard Utility
5. After finishing setting all of the parameters, click on Diagnose
ÆGo or the Go icon to start the test. If the JetCards and pins are functioning normally, you will see OK message on the
Test Report. If connections are not correct, you will see ERR message on the Test Report.
You can save or print the report by clicking on the icons of the menu bar.
Uninstalling Korenix JetCard Utility
1. Click on Start
ÆProgramÆJetCard UtilityÆUninstall.
2. In the window to open next, click on Yes to start the uninstallation.
3. The uninstallation is now complete. Click on OK to leave the uninstallation window.
Korenix JetCard Series User’s Manual 4-7
4-8 Korenix JetCard Series User’s Manual
Chapter 5
5
Cable Selection and Cable Wiring
This chapter includes information of how to select cables for your systems and cable pin assignments.
The following topics are covered in this chapter:
Cable Selection and Pin Assignments
RS-232/422/485 Cable Wiring
Cable Selection and Pin Assignments
Korenix provides 4 types of cables for JetCard Series, which are CM62M9x8, CM62M25x8,
CM37M9x4 and CM37M25x4. These 4 cables can convert JetCard DB37/DB62 connectors into
4/8 sets of DB9 or DB25 male connectors.
Accessories
1. CM37M9x4-60: Male DB37 to 4-port male DB9 cable, 60cm (for JetCard 1204,
1204w 1404, 1404i, 1608, 1608w)
2. CM37M25x4-60: Male DB37 to 4-port male DB25 cable, 60cm (for JetCard 1204,
1204w, 1404, 1404i, 1608, 1608w)
3. CM62M9x8-100: Male DB62 to 8-port male DB9 cable, 60cm (for JetCard 1208,
1208w)
4. CM62M25x8-100: Male DB62 to 8-port male DB25 cable, 60cm (for JetCard 1208,
1208w)
5. CV62M9x8-100: Male VHDCI 68 to 8-port male DB9 connection cable, 100cm (for
JetCard 1208L)
6. CV62M25x8-100: Male VHDCI 68 to 8-port male DB25 connection cable, 100cm
(for JetCard 1208L)
5-2 Korenix JetCard Series User’s Manual
Cable Selection and Cable Wiring
JetCard 1208, JetCard 1208w, JetCard 1204, JetCard 1204w, JetCard 1404, JetCard 1404i Pin
Assignments
DB-9
Pin
RS-232 RS-422 RS-485
4 wires
RS-485
2 wires
5 GND GND GND GND
9
CTS-(A)
Korenix JetCard Series User’s Manual 5-3
DB-25
Pin
RS-232 RS-422 RS-485
4 wires
RS-485
2 wires
7 GND GND GND GND
22
CTS-(A)
5-4 Korenix JetCard Series User’s Manual
JetCard 1608, JetCard 1608w Pin Assignments
DB-9
Pin
RS-232 RS-422 RS-485
4 wires
RS-485
2 wires
Cable Selection and Cable Wiring
5 GND GND GND GND
6 DSR
7 RTS
8 CTS
9
DB-25
Pin
RS-232 RS-422 RS-485
4 wires
RS-485
2 wires
7 GND GND GND GND
20 DTR RxD-(A)
22
Korenix JetCard Series User’s Manual 5-5
5-6 Korenix JetCard Series User’s Manual
Cable Selection and Cable Wiring
RS-232/422/485 Cable Wiring
In this section, we will talk about RS-232/422/485 cable wiring in detail by presenting several wiring examples.
Example 1
Topology Type
Model Name
Point-to-Point RS-232
JetCard 1204/1204w, JetCard 1208/1208w
In this example, you can use standard DB9 or DB25 cross-over cables to connect 2 PCs with
JetCard Series RS-232 Multiport Serial Cards installed. Since the handshaking signals (CTS,
RTS, DTR, DSR) are connected too, you can select Hardware Handshaking options in your application software for communications. Please note that RS-232 transmission distance is up to 15m (50ft).
Example 2
Topology Type
Model Name
Point-to-Point RS-422
JetCard 1402, JetCard 1402i
JetCard 1404, JetCard 1404i
In this example, you can use 4 twisted pairs of cables and a ground cable to connect 2 PCs with JetCard Series RS-422/485 Multiport Serial Cards installed. These JetCards are configured to RS-422 mode. Since 2 of the twisted pairs of cables (CTS+(B), CTS-(A),
RTS+(B), RTS-(A)) are connected too, you can select Hardware Handshaking options in your application software for communications. Please note that RS-422 transmission distance is up to 1200m (5000ft).
Example 3
Topology Type Point-to-Point 2-wire RS-485
Korenix JetCard Series User’s Manual 5-7
Model Name JetCard 1402, JetCard 1402i
JetCard 1404, JetCard 1404i
In this example, you can use 1 twisted pair of cables and a ground cable to connect 2 PCs with JetCard Series RS-422/485 Multiport Serial Cards installed. These 2 JetCards are configured to 2-wire RS-485 mode. Please note that RS-485 transmission distance is up to
1200m (5000ft).
Example 4
Topology Type
Model Name
Point-to-Point 4-wire RS-485
JetCard 1402, JetCard 1402i
JetCard 1404, JetCard 1404i
In this example, you can use 2 twisted pairs of cables and 1 ground cable to connect 2 PCs with JetCard Series RS-422/485 Multiport Serial Cards installed. These 2 JetCards are configured to 4-wire RS-485 mode. Please note that RS-485 transmission distance is up to
1200m (5000ft).
Example 5
Topology Type
Model Name
Multidrop 2-wire RS-485
JetCard 1402, JetCard 1402i
JetCard 1404, JetCard 1404i
5-8 Korenix JetCard Series User’s Manual
Cable Selection and Cable Wiring
In this case, you can use 1 twisted pair of cables and 1 ground cable to connect multiple PCs with JetCard Series RS-422/485 Multiport Serial Cards installed via Bus interface. All
JetCards are configured to 2-wire RS-485 mode. Please note that RS-485 transmission distance is up to 1200m (5000ft). In this topology, the number of connected devices
(JetCards) can be up to 32.
Korenix JetCard Series User’s Manual 5-9
Example 6
Topology Type
Model Name
Multidrop 4-wire RS-485
JetCard 1402, JetCard 1402i
JetCard 1404, JetCard 1404i
In this example, you can use 2 twisted pairs of cables and 1 ground cable to connect multiple
PCs with JetCard Series RS-422/485 Multiport Serial Card installed. All JetCards are configured to 4-wire RS-485 mode. Please note that RS-485 transmission distance is up to
1200m (5000ft). In this topology, the number of connected devices (PCs) can be up to 32.
Example 7
Topology Type
Model Name
RS-422 Broadcasting
JetCard 1402, JetCard 1402i
JetCard 1404, JetCard 1404i
In this example, you can use 2 twisted pairs of cables and 1 ground cable to connect 1 host
PC and multiple RS-422 devices. The host PC is configured to RS-422 mode. Please note that RS-422 transmission distance is up to 1200m (5000ft). In this topology, the number of connected RS-422 devices can be up to 32.
5-10 Korenix JetCard Series User’s Manual
A
Appendix A
Selection Guide
Cable Selection and Cable Wiring
Korenix JetCard Series User’s Manual 5-11
B
Appendix B
Revision History
V1.0
V1.1
V1.2
V1.3
The first released version.
Add JetCard 1404/i
Mar. 2005
Aug. 2005
Add JetCard 2105/2205/1608 Dec. 2008
Add JetCard 1208L Jan. 2010
About Korenix
Less Time At Work! Fewer Budget on applications!
The Korenix business idea is to let you spend less time at work and fewer budget on your applications.
Do you really want to go through all the troubles but still end up with low quality products and lousy services? Definitely not! This is why you need Korenix. Korenix offers complete product selection that fulfills all your needs for applications. We provide easier, faster, tailor-made services, and more reliable solutions. In Korenix, there is no need to compromise. Korenix takes care of everything for you!
Fusion of Outstandings
You can end
your searching here. Korenix Technology is your one-stop supply center for industrial communications and networking products. Korenix Technology is established by a group of professionals with more than 10 year experience in the arenas of industrial control, data communications and industrial networking applications. Korenix Technology is well-positioned to fulfill your needs and demands by providing a great variety of tailor-made products and services. Korenix’s industrial-grade products also come with quality services. No more searching, and no more worries.
Korenix Technology stands by you all the way through.
Core Strength---Competitive Price and Quality
With our work experience and in-depth know-how of industrial communications and networking, Korenix
Technology is able to combine Asia’s research / development ability with competitive production cost and with quality service and support.
Global Sales Strategy
Korenix’s global sales strategy focuses on establishing and developing trustworthy relationships with value added distributors and channel partners, and assisting OEM distributors to promote their own brands. Korenix supplies products to match local market requirements of design, quality, sales, marketing and customer services, allowing Korenix and distributors to create and enjoy profits together.
Quality Services
KoreCARE ---
KoreCARE is Korenix Technology’s global service center, where our professional staffs are ready to solve your problems at any time and in real-time. All of Korenix’s products have passed ISO-9000/EMI/CE/FCC/UL certifications, fully satisfying your demands for product quality under critical industrial environments. Korenix global service center’s e-mail is [email protected]
5 Years Warranty
Each of Korenix’s product line is designed, produced, and tested with high industrial standard. Korenix warrants that the Product(s) shall be free from defects in materials and workmanship for a period of five
(5) years from the date of delivery provided that the Product was properly installed and used. This warranty is voided if defects, malfunctions or failures of the warranted Product are caused by damage resulting from force measure (such as floods, fire, etc.), environmental and atmospheric disturbances, other external forces such as power line disturbances, host computer malfunction, plugging the board in under power, or incorrect cabling; or the warranted Product is misused, abused, or operated, altered and repaired in an unauthorized or improper way
Korenix Technologies Co., Ltd.
Business service :
Customer service:
B-2 Korenix JetCard Series User’s Manual
advertisement
* Your assessment is very important for improving the workof artificial intelligence, which forms the content of this project
Related manuals
advertisement
Table of contents
- 6 Overview
- 7 Product Features
- 7 Package Checklist
- 7 Installation Guide
- 10 Introduction
- 11 Panel Layout
- 13 Dimensions (Unit-mm)
- 18 Connecter
- 20 DIP Switch and Jumper Settings
- 20 JetCard 2105/2205 LED Indicators
- 21 JetCard 1608 DIP Switch
- 23 Installing Your JetCard
- 24 Removing Your JetCard
- 26 Windows
- 26 Windows XP/2003
- 26 Follow the hardware installation instructions in the previous chapter to install the JetCard 2105/2205 first. Windows XP/2003 will automatically detect the new JetCard 2105/2205 after you power on your PC.
- 26 1. Found new hardward
- 26 2. Insert the JetCard software CD into the CD-ROM.
- 26 3. Select Hardware tab, and click on the Device Manager button.
- 26 4. Click on the Properties button
- 27 5. Click on the Update Driver button
- 27 7. In the window to open next, select Install from a list or specific location (Advanced), and click on Next to continue.
- 28 8. In the window that opens next, select Search for the best driver in these locations, and check Include this location in the search. Click on Next to start installing the driver.
- 29 9. C:JetCard CD V1.4\jetcard_2105_2205_driver\Netrtls.inf
- 40 Windows 2000
- 43 Windows 98/ME
- 46 Windows NT
- 49 Linux
- 52 Installing Korenix JetCard Utility
- 55 Using Korenix JetCard Utility
- 55 JetCard Diagnostic Test
- 57 Uninstalling Korenix JetCard Utility
- 60 Cable Selection and Pin Assignments
- 65 RS-232/422/485 Cable Wiring
- 69 Selection Guide
- 71 Appendix B Revision History
- 72 About Korenix