User manual | UR28M Getting Started

USB AUDIO INTERFACE
EN
DE
FR
ES
IT
JA
FCC INFORMATION (U.S.A.)
1. IMPORTANT NOTICE:
DO NOT MODIFY THIS UNIT!
This product, when installed as indicated in the
instructions contained in this manual, meets FCC
requirements. Modifications not expressly
approved by Yamaha may void your authority,
granted by the FCC, to use the product.
2. IMPORTANT: When connecting this product to
accessories and/or another product use only high
quality shielded cables. Cable/s supplied with this
product MUST be used. Follow all installation
instructions. Failure to follow instructions could void
your FCC authorization to use this product in the
USA.
3. NOTE: This product has been tested and found to
comply with the requirements listed in FCC
Regulations, Part 15 for Class “B” digital devices.
Compliance with these requirements provides a
reasonable level of assurance that your use of this
product in a residential environment will not result
in harmful interference with other electronic
devices. This equipment generates/uses radio
frequencies and, if not installed and used according
to the instructions found in the users manual, may
cause interference harmful to the operation of other
electronic devices. Compliance with FCC
regulations does not guarantee that interference
will not occur in all installations. If this product is
found to be the source of interference, which can
be determined by turning the unit “OFF” and “ON”,
please try to eliminate the problem by using one of
the following measures:
Relocate either this product or the device that is
being affected by the interference.
Utilize power outlets that are on different branch
(circuit breaker or fuse) circuits or install AC line
filter/s.
In the case of radio or TV interference, relocate/
reorient the antenna. If the antenna lead-in is 300
ohm ribbon lead, change the lead-in to co-axial
type cable.
If these corrective measures do not produce
satisfactory results, please contact the local retailer
authorized to distribute this type of product. If you
can not locate the appropriate retailer, please
contact Yamaha Corporation of America, Electronic
Service Division, 6600 Orangethorpe Ave, Buena
Park, CA90620
The above statements apply ONLY to those
products distributed by Yamaha Corporation of
America or its subsidiaries.
* This applies only to products distributed by YAMAHA CORPORATION OF AMERICA.
(class B)
COMPLIANCE INFORMATION STATEMENT
(DECLARATION OF CONFORMITY PROCEDURE)
Responsible Party : Yamaha Corporation of America
Address : 6600 Orangethorpe Ave., Buena Park, Calif. 90620
Telephone : 714-522-9011
Type of Equipment : USB AUDIO INTERFACE
Model Name : UR28M
This device complies with Part 15 of the FCC Rules.
Operation is subject to the following two conditions:
1) this device may not cause harmful interference, and
2) this device must accept any interference received including interference that may cause undesired
operation.
See user manual instructions if interference to radio reception is suspected.
* This applies only to products distributed by YAMAHA CORPORATION OF AMERICA.
(class b korea)
2
UR28M Getting Started
(FCC DoC)
English
Contents
PRECAUTIONS............................................4
Introduction .................................................7
A Message From the Development Team......... 7
Included Accessories ........................................ 7
How to Read the Manual................................... 8
Panel Controls and Terminals .................10
Rear Panel ...................................................... 10
Front Panel...................................................... 11
Setup ..........................................................12
1. Setting up the Power Supply ....................... 12
2. Installing Cubase AI .................................... 13
3. Installing TOOLS for UR28M....................... 14
4. Downloading the Licenses (Activation) ....... 16
Basic Operations ......................................17
Introduction...................................................... 17
Connection Example ....................................... 17
Configuring Audio Driver Settings on
the DAW Software........................................... 17
Troubleshooting........................................19
Appendix....................................................21
Contents of the Operation Manual .................. 21
Uninstalling TOOLS for UR28M ...................... 21
Specifications .................................................. 23
UR28M Getting Started
3
English
PRECAUTIONS
Water warning
PLEASE READ CAREFULLY
BEFORE PROCEEDING
* Please keep this manual in a safe
place for future reference.
• Do not expose the device to rain, use it near water or in
damp or wet conditions, or place on it any containers
(such as vases, bottles or glasses) containing liquids
which might spill into any openings. If any liquid such as
water seeps into the device, turn off the power immediately
and unplug the power cord from the AC outlet. Then have
the device inspected by qualified Yamaha service
personnel.
• Never insert or remove an electric plug with wet hands.
WARNING
Always follow the basic precautions listed below
to avoid the possibility of serious injury or even
death from electrical shock, short-circuiting,
damages, fire or other hazards. These
precautions include, but are not limited to, the
following:
Power supply/AC power adaptor
• Do not place the power cord near heat sources such as
heaters or radiators, and do not excessively bend or
otherwise damage the cord, place heavy objects on it, or
place it in a position where anyone could walk on, trip
over, or roll anything over it.
• Only use the voltage specified as correct for the device.
The required voltage is printed on the name plate of the
device.
• Use the specified adaptor (PA-130 or an equivalent
recommended by Yamaha) only. Using the wrong adaptor
can result in damage to the device or overheating.
Fire warning
• Do not put burning items, such as candles, on the unit. A
burning item may fall over and cause a fire.
If you notice any abnormality
• When one of the following problems occur, immediately
turn off the power and disconnect the electric plug from the
outlet. Then have the device inspected by Yamaha service
personnel.
- The power cord or plug becomes frayed or damaged.
- It emits unusual smells or smoke.
- Some object has been dropped into the device.
- There is a sudden loss of sound during use of the device.
• If this device or the AC power adaptor should be dropped or
damaged, immediately turn off the power, disconnect the
electric plug from the outlet, and have the device inspected
by qualified Yamaha service personnel.
• Check the electric plug periodically and remove any dirt or
dust which may have accumulated on it.
Do not open
• This device contains no user-serviceable parts. Do not
open the device or attempt to disassemble the internal
parts or modify them in any way. If it should appear to be
malfunctioning, discontinue use immediately and have it
inspected by qualified Yamaha service personnel.
CAUTION
Always follow the basic precautions listed below
to avoid the possibility of physical injury to you or
others, or damage to the device or other
property. These precautions include, but are not
limited to, the following:
Power supply/AC power adaptor
• Do not cover or wrap the AC power adaptor with a cloth or
blanket.
PA_en_1
4
UR28M Getting Started
1/2
• Remove the electric plug from the outlet when the device is
not to be used for extended periods of time, or during
electrical storms.
Location
• Do not place the device in an unstable position where it
might accidentally fall over.
English
• When removing the electric plug from the device or an
outlet, always hold the plug itself and not the cord. Pulling
by the cord can damage it.
Yamaha cannot be held responsible for damage
caused by improper use or modifications to the
device, or data that is lost or destroyed.
Always turn the power off when the device is not in use.
Even when the power is in standby status, electricity is
still flowing to the device at the minimum level. When you
are not using the device for a long time, make sure you
unplug the power cord from the wall AC outlet.
• Do not place the device in a location where it may come
into contact with corrosive gases or salt air. Doing so may
result in malfunction.
• Before moving the device, remove all connected cables.
• When setting up the device, make sure that the AC outlet
you are using is easily accessible. If some trouble or
malfunction occurs, immediately turn off the power and
disconnect the plug from the outlet. Even when the power
is turned off, electricity is still flowing to the product at the
minimum level. When you are not using the product for a
long time, make sure to unplug the power cord from the
wall AC outlet.
Connections
• Before connecting the device to other devices, turn off the
power for all devices.
Before turning the power on or off for all devices, set all
volume levels to minimum.
Maintenance
• Remove the power plug from the AC outlet when cleaning
the device.
Handling caution
• Do not rest your weight on the device or place heavy
objects on it, and avoid use excessive force on the buttons,
switches or connectors.
• Do not use the headphones for a long period of time at a
high or uncomfortable volume level, since this can cause
permanent hearing loss. If you experience any hearing loss
or ringing in the ears, consult a physician.
PA_en_1
2/2
UR28M Getting Started
5
English
NOTICE
To avoid the possibility of malfunction/ damage
to the product, damage to data, or damage to
other property, follow the notices below.
• Do not use the device in the vicinity of a TV, radio, stereo
equipment, mobile phone, or other electric devices.
Otherwise, the device, TV, or radio may generate noise.
• Do not expose the device to excessive dust or vibrations,
or extreme cold or heat (such as in direct sunlight, near a
heater, or in a car during the day) to prevent the possibility
of panel disfiguration, damage to the internal components
or unstable operation.
• Do not place vinyl, plastic or rubber objects on the device,
since this might discolor the panel.
• When cleaning the device, use a soft, dry/dry or slightly
damp cloth. Do not use paint thinners, solvents, cleaning
fluids, or chemical-impregnated wiping cloths.
• This disk containing the software is not meant for use with
an audio/visual system (CD player, DVD player, etc.). Do
not attempt to use the disk on equipment other than a
computer.
Information
• The software included in the Cubase AI DVD-ROM and the
copyrights thereof are under exclusive ownership by
Steinberg Media Technologies GmbH.
• The software included in the TOOLS for UR28M CD-ROM
and the copyrights thereof are under exclusive ownership
by Yamaha.
• This manual is the exclusive copyrights of Yamaha
Corporation.
• Copying of the software or reproduction of this manual in
whole or in part by any means is expressly forbidden
without the written consent of the manufacturer.
• Steinberg Media Technologies GmbH and Yamaha
Corporation make no representations or warranties with
regard to the use of the software and documentation and
cannot be held responsible for the results of the use of this
manual and the software.
• The screen displays as illustrated in this manual are for
instructional purposes, and may appear somewhat
different from the screens which appear on your computer.
• Copying of the commercially available musical data
including but not limited to MIDI data and/or audio data is
strictly prohibited except for your personal use.
6
UR28M Getting Started
• This product incorporates and bundles computer
programs and contents in which Steinberg Media
Technologies GmbH and Yamaha Corporation own
copyrights or with respect to which it has license to use
others' copyrights. Such copyrighted materials include,
without limitation, all computer software, style files, MIDI
files, WAVE data, musical scores and sound recordings.
Any unauthorized use of such programs and contents
outside of personal use is not permitted under relevant
laws. Any violation of copyright has legal consequences.
DON'T MAKE, DISTRIBUTE OR USE ILLEGAL COPIES.
• Windows is a registered trademark of Microsoft®
Corporation in the United States and other countries.
• Apple, Mac and Macintosh are trademarks of Apple Inc.,
registered in the U.S. and other countries.
• Steinberg and Cubase are registered trademarks of
Steinberg Media Technologies GmbH.
• The company names and product names in this manual are
the trademarks or registered trademarks of their respective
companies.
• Software may be revised and updated without prior notice.
Introduction
A Message From the
Development Team
Thank you for choosing the UR28M USB Audio
Interface. The UR28M brings the sum total of our
experience and know-how together with
invaluable feedback from our customers
throughout the world. Throughout the Yamaha nseries and Steinberg MR series our focus has
been on integrating consistently outstanding
sonic design with features and software that are
truly useful from a musician’s perspective. The
UR28M carries on this uncompromising
approach, offering refined sound and
functionality in a compact unit.
With the goal of creating a product that would be
of maximum value for the longest time in mind,
the development process began with in-depth
review of the many comments received from
users as a starting point for the design and basic
specifications. Visual design, the feel of buttons
and knobs, trial-and-error sonic evaluation of
parts, and seamless software integration are just
some of the elements to which every member of
the development team devoted their full attention
and passion. The entire team is rightly proud of
the results, and we are delighted to be able to
offer this product to our valued customers.
But this is just the beginning. The most important
chapter unfolds when our customers use the
product to support and augment their creativity,
making it a part of their musical lives. Our
greatest hope is that we are able to contribute in
some way to the creation and expression of new
music that will bring our customers’ artistic vision
to life.
Included Accessories
English
Introduction
Accessories
• AC power adaptor
(PA-130 or equivalent)
• Getting Started (this book)
• ESSENTIAL PRODUCT LICENSE
INFORMATION card
• TOOLS for UR28M CD-ROM
• Cubase AI DVD-ROM
• USB cable
NOTICE
If the ESSENTIAL PRODUCT LICENSE
INFORMATION card is lost or stolen,
Steinberg Media Technologies GmbH
and Yamaha Corporation cannot
reissue it.
Disk Contents
TOOLS for UR28M CD-ROM
• Operation Manual
This is the Operation Manual in PDF
file format. For details, refer to the
section “How to Read the Manual”
(page 8).
• TOOLS for UR28M
TOOLS for UR28M is necessary when
connecting the device to a computer.
When you install the TOOLS for
UR28M, the following two software
programs will be installed. For
instructions on installation, refer to the
section “Setup” (page 12).
The Steinberg Hardware Development Team
UR28M Getting Started
7
Introduction
English
- Yamaha Steinberg USB Driver
This software allows
communication between the device
and a computer.
- Steinberg UR28M Applications
This software allows setting the
parameters of the device from a
computer or using the Link function
between the device and Cubase
series. The software consists of the
following four software
components.
• dspMixFx UR28M
This software lets you set the
device when using it with a DAW
(Digital Audio Workstation)
software other than Cubase
series.
• UR28M Extension
This software allows you to link the
device with Cubase series (for
versions which supports the link
function).
To use this Link function, you will
need to install Cubase series
version 5.5 or higher.
• Sweet Spot Morphing Channel
Strip (VST Plug-in version)
This processing effect is a multieffect that combines compressor
and equalizer. This is the VST
Plug-in version (VST3.0) of the
DSP effect equipped with the
device.
• REV-X (VST Plug-in version)
This processing effect is a digital
reverb platform developed by
Yamaha for professional audio
devices. This is the VST Plug-in
version (VST3.0) of the DSP effect
equipped with the device.
Cubase AI DVD-ROM
Cubase AI
Cubase AI is an entry-level program
modeled on the flagship Cubase DAW
software made by Steinberg, and
provides basic function for the music
recording/production. For instructions
on installation, refer to the section
“Setup” (page 12).
NOTE
For the latest information on the software
contained in the accessory disk, please
see the Steinberg web site below. Future
upgrades of application and system
software and any changes in
specifications are announced separately
on the website.
http://www.steinberg.net
How to Read the
Manual
Types and Contents
Getting Started (this book)
Read this manual when setting up the
device. After finishing the setup as
indicated in this manual, read the
Operation Manual.
8
UR28M Getting Started
Introduction
This manual provides instructions on
how to use the device and gives
detailed information on specific
functions. It is included in the TOOLS
for UR28M CD-ROM.
NOTE
• For contents of the operation manual,
refer to the section “Contents of the
Operation Manual” (page 21).
• To view PDF files, you will need to install
Adobe Reader on you computer. You
can download the latest Adobe Reader
at the following web site.
http://www.adobe.com
Conventions
Windows or Mac
When the procedures or explanations
are specific to only one of the
platforms, Windows or Mac, this is
properly indicated in the manual. When
the platforms do not appear,
procedures or explanations are for
both Windows and Mac.
3. Click the [Control Panel] button.
English
Operation Manual (PDF file)
Keyboard Shortcuts
[Windows modifier key]/[Mac modifier
key]+[key] shows the shortcut keys.
For example, [Ctrl]/[command]+[Z]
means “press [Ctrl] under Windows or
[command] under Mac, then press
[Z].”
Different Cubase Programs
The phrase “Cubase series” applies to
all Cubase programs and versions
(except Cubase LE). If the instructions
are only for Cubase, “Cubase only”
appears in the manual.
Screens
This manual predominantly uses
screenshots of Windows. However,
Mac screenshots are used when
instructions of the function apply only
to the Mac.
Procedures
“  ” appears on some procedures in
the manual. For example, the string
[Devices]  [Device Setup]  [Control
Panel] indicates that you should
perform the procedures in the following
order.
1. Click the [Devices] menu.
2. Select the [Device Setup] option.
UR28M Getting Started
9
Panel Controls and Terminals
English
Panel Controls and Terminals
Rear Panel
1 DC IN 12V
2 Grounding screw
3 2TR IN (3.5mm, stereo)
4 USB2.0 (USB port)
5 S/PDIF IN/OUT (coaxial)
6 PHONES 1/2 (phone type, stereo)
7 LINE OUTPUT A–C (phone type,
balanced/unbalanced)
8 LINE INPUT 3/4 (phone type,
balanced/unbalanced)
9 MIC/LINE/HI-Z 1/2 (XLR/phone type,
balanced/unbalanced)
10
UR28M Getting Started
Panel Controls and Terminals
English
Front Panel
1 HI-Z switch
2 PAD switch
3 +48V button
4 INPUT GAIN knob 1/2
5 PHONES knob 1/2
6 2TR IN LEVEL knob
7 2TR IN ON button
8 INPUT meter
9 OUTPUT meter
) OUTPUT buttons A–C
! SOURCE SELECT button
@ MIX 1–3 lamp
# DIM button
$ MONO MIX button
% OUTPUT LEVEL knob
^ MUTE button
& Power button
* Word clock source lamp
UR28M Getting Started
11
Setup
English
Setup
NOTICE
• To avoid generating unwanted noise,
make sure there is adequate distance
between the power adaptor and the
device.
1. Setting up the
Power Supply
• Avoid tightening the cord more than
Connecting the AC Power
Adaptor
1. Insert the plug of the AC power
adaptor into the DC IN 12V jack
on the device.
To prevent accidental unplugging
of the cable during operation,
wrap the cable of AC power
adaptor around the cable clip.
necessary or pulling on the cord
strongly while it is wrapped around
the cable clip, in order to prevent
wear on the cord or possible
breakage of the clip.
Turning the Power On
and Off
Power on
Press the power button ( ). The power
button will light.
AC outlet
Power off
2. Insert the plug of the AC power
adaptor into the proper AC outlet
on the wall.
WARNING
Only use the included AC power
adaptor (or an equivalent
recommended by Yamaha). Using the
wrong adaptor can result in damage
to the device or overheating.
CAUTION
Remove the electric plug from the
outlet when the device is not be
used for extended periods of time, or
during electrical storms.
12
UR28M Getting Started
Hold down the power button ( ) for
over one second. The power button will
light dimly.
If one of the following actions is
performed, the power of the device will
turn off automatically after thirty
minutes elapses. The power button will
flash during the thirty-minute interval.
• Turning off the computer.
• Disconnecting the USB cable
between the device and the
computer.
For instructions on enabling/disabling
this automatic power off function, refer
to the section “Control Panel of the
Audio Driver” in the Operation Manual.
Setup
Before you connect external devices
to the device, turn off the power to all
devices after setting all volume
levels to minimum. Otherwise,
electrical shock, hearing loss, or
damage to the components may
occur.
NOTICE
Even when the device is turned off,
electricity is still flowing to the device at
the minimum level. When you are not
using the device for a long time, make
sure you unplug the AC power adaptor
from the wall AC outlet.
2. Installing Cubase
AI
NOTE
• You are only permitted to use this
software pursuant to the terms and
conditions of the “End User License
Agreement” shown during the
installation.
3. When the “WELCOME TO
English
CAUTION
CUBASE AI” window appears,
click the corresponding national
flag icon to choose your
preferred language.
NOTE
If this window does not appear
automatically, open the DVD-ROM
then double-click the file “Start
Center.”
4. Follow the on-screen
instructions to install the
software.
Installation may take a few minutes.
User Registration and
Product Registration
Register your personal information and
products on “MySteinberg” in the
Steinberg web site. For details, refer to
the following web site.
http://www.steinberg.net/en/
mysteinberg.html
The installation for Cubase AI is now
completed.
• If you have already installed a version of
Cubase series that is compatible with
operation with the device (page 8), the
instructions on Installing Cubase AI
described below are not necessary.
Installation
1. Start the computer and log on to
the Administrator account.
2. Insert the Cubase AI DVD-ROM
into the DVD-ROM drive.
UR28M Getting Started
13
Setup
English
3. Installing TOOLS
for UR28M
Example warning messages on
Windows Vista/Windows 7
NOTE
You are only permitted to use this
software pursuant to the terms and
conditions of the “License Agreement”
shown during the installation.
Windows.................................page 14
Mac .........................................page 15
Windows
Preparation
If the following warning messages
appear during the installation, click
[Continue Anyway], [Yes], or [Install].
Installation
1. Turn off the computer and
Example warning message on
Windows XP
device.
2. Disconnect all USB devices
other than the mouse and
keyboard from the computer.
3. Start the computer and log on to
the Administrator account.
4. Insert the TOOLS for UR28M CDROM into the CD-ROM drive.
5. Open the CD-ROM then doubleclick the file “setup.exe.”
6. Follow the on-screen
instructions to install the
software.
Install the following software in
order.
-Yamaha Steinberg USB Driver
-Steinberg UR28M Applications
14
UR28M Getting Started
Setup
completed, click [Finish].
If a window requiring you to restart
your computer appears, follow the
on-screen instructions and restart
the computer.
Device Connection
8. Connect the device directly to
the computer by using the
included USB cable.
Make sure to not connect it to a
USB hub.
9. Turn on the device.
Confirmation of Installation
English
7. When installation has been
13. Open the “Device Manager”
window as follows.
Windows XP:
[Start]  [Control Panel] 
([Performance and Maintenance])
 [System]  [Hardware] tab 
[Device Manager]
Windows Vista/Windows 7:
[Start]  [Control Panel] 
([Hardware and Sound])  [Device
Manager]
14. Click on the [+] mark or [>] mark
next to “Sound, video and game
controllers.”
Windows XP:
The “Found New Hardware
Wizard” window appears. Go on to
step 10.
15. Confirm that the device name is
Windows Vista/Windows 7:
Go on to step 13.
Installation of the TOOLS for UR28M is
now completed.
listed.
10. If the “Can Windows connect to
Windows Update to search for
software?” message appears in
the middle of the window, select
“No, not this time” then click
[Next].
11. Confirm that the “Install the
software automatically” has
been selected then click [Next].
12. When the installation has been
completed, click [Finish].
Mac
Installation
1. Turn off the computer and
device.
2. Disconnect all USB devices
other than the mouse and
keyboard from the computer.
3. Start the computer and log in to
the Administrator account.
4. Insert the TOOLS for UR28M CDROM into the CD-ROM drive.
UR28M Getting Started
15
Setup
English
5. Open the CD-ROM then doubleclick the file “TOOLS for
UR28M.mpkg.”
6. Follow the on-screen
instructions to install the
software.
7. When installation has been
completed, click [Restart] to
restart the computer.
Device Connection
8. Connect the device directly to
the computer by using a USB
cable.
Make sure to not connect it to a
USB hub.
9. Turn on the device.
Confirmation of Installation
10. Open the “Audio MIDI Setup”
window as follows.
[Macintosh HD]  [Applications] 
[Utilities]  [Audio MIDI Setup]
11. Confirm that the device name is
listed in the following.
Mac OS X 10.5:
In “Properties For:”
Mac OS X 10.6:
In the left column
Installation of the TOOLS for UR28M is
now completed.
4. Downloading the
Licenses (Activation)
To use the Sweet Spot Morphing
Channel Strip (VST Plug-in version)
and REV-X (VST Plug-in version) which
are installed in Step 3 in “Installing
TOOLS for UR28M” (page 14),
download their licenses via the Internet
by using the activation code described
on the ESSENTIAL PRODUCT
LICENSE INFORMATION card.
1. Launch the “eLicenser Control
Center” as follows.
Windows:
[Start]  [All Programs] 
[eLicenser]  [eLicenser Control
Center]
Mac:
[Macintosh HD]  [Applications] 
[eLicenser Control Center]
2. Click [Enter Activation Code].
3. Enter the Activation Code
described on the included
ESSENTIAL PRODUCT LICENSE
INFORMATION card.
4. Follow the on-screen
instructions to download the
licenses.
NOTE
If you connect a USB-eLicenser
(USB protection device) to your
computer, a window requiring you to
select the destination of the license
appears. Follow the on-screen
instructions to select the device.
The download licenses are now
completed.
16
UR28M Getting Started
Basic Operations
Connection Example
Computer
English
Basic Operations
Monitor speakers
Introduction
This section explains the connection
examples and audio driver settings on
DAW software. For more detailed
usage, refer to the section “Usage
Examples” in the Operation Manual.
CAUTION
Make sure to set all volume levels to
minimum before connecting or
disconnecting the external device.
Otherwise, high-volume output may
damage your hearing or equipment.
NOTICE
Be sure to observe the following points
when connecting to the computer’s
USB interface. Failing to do so may
result in the computer freezing or
shutting down, as well as corruption or
even loss of data.
• Before turning on/off the device or
plugging/unplugging the USB cable,
quit any open application software on
the computer.
• Before turning on the device, exit
from any power-saving mode of the
computer (such as suspend, sleep,
standby).
• Before turning on the device, connect
the device to the computer.
• Wait for six seconds or more between
these operations: (1) when turning off
the device then on again, or (2) when
alternately connecting/disconnecting
the USB cable.
Portable audio
player
Headphones Guitar Microphone
Configuring Audio
Driver Settings on
the DAW Software
Cubase Series Programs
1. Make sure that all applications
have been quit.
2. Connect the device directly to
the computer by using the
included USB cable.
NOTE
(Windows only) Make sure to use the
same USB port as the one used in
the installation procedure when you
connect the device to the computer
again. If you connect them to a
different USB port, you will have to
install the driver again.
3. Turn on the device.
UR28M Getting Started
17
Basic Operations
English
4. Launch the Cubase series
program as follows.
Windows:
[Start]  [All Programs] 
[Steinberg (Cubase series)] 
[(Cubase series)]
Mac:
[Macintosh HD]  [Applications] 
[(Cubase series)]
5. When the following window
appears while the Cubase series
program is launching, confirm
that the device is selected, then
click [OK].
The audio driver settings are now
completed.
For instructions on using Cubase
series programs, refer to the PDF
manual, available from [Help] in the
Cubase series menu. For instructions
on using the device, refer to the
Operation Manual.
Programs Other Than
Cubase Series
1. Make sure that all applications
have been quit.
2. Connect the device directly to
the computer by using the
included USB cable.
18
UR28M Getting Started
3. Turn on the device.
4. Launch the DAW software.
5. Open the audio driver settings
window.
6. Set the audio driver settings.
The audio driver settings are now
competed.
For instructions on using the DAW
software, refer to your particular DAW’s
software manual. For instructions on
using the device, refer to the Operation
Manual.
Troubleshooting
Turning Off the Power
Automatically, or Flashing
the Power Button
• The automatic power off function is
enabled.
Refer to the section “Control Panel of
the Audio Driver” in the Operation
Manual to disable this function.
No Sound
• Are the volume controls of the
• Was the power of the device turned
on before starting the DAW
software?
Before starting the DAW software,
connect the device to a computer
and turn on the power of the device.
• Is the device connected to a
computer via a USB hub?
Connect it directly without using a
USB hub.
• Has TOOLS for UR28M been
installed properly?
Refer to Step 3 in “Installing TOOLS
for UR28M” (page 14) to confirm it.
• Are any USB devices you are not
device set to appropriate levels?
Confirm the OUTPUT LEVEL knob
and PHONES knob.
using connected to the computer?
Remove them then confirm the
sound.
• Are the microphones and monitor
• Are any other applications running
speakers connected to the device
properly?
Refer to the section “Connection
Examples” (page 17) to confirm the
connection.
at the same time?
Quit all applications you are not using
then confirm the sound.
• Are the audio driver settings on
DAW software set properly?
Refer to the section “Configuring the
Audio Driver Settings on DAW
Software” (page 17) to set it.
• Is the “ASIO Driver” setting on the
Cubase series program set
properly?
From the Cubase series menu, open
the [Devices]  [Device Setup] 
[VST Audio System], then confirm
that the “Yamaha Steinberg USB
ASIO” (Windows) or “Steinberg
UR28M” (Mac) is selected on the
“ASIO Driver.”
English
Troubleshooting
Unusual Sound (noise,
interruption, or distortion)
• Is the INPUT meter lit in red?
Lower the INPUT GAIN level, or turn
on the PAD switch.
• Is the buffer size set too low?
Refer to the section “Control Panel of
the Audio Driver” in the Operation
Manual to confirm the buffer size.
• Is the Clock Source lamp flashing?
The Clock Source lamp flashes when
the word clock is not synchronized to
the clock source. Refer to the section
“Control Panel of the Audio Driver” in
the Operation Manual to set it.
UR28M Getting Started
19
Troubleshooting
English
• Does your computer satisfy the
system requirements?
Confirm the system requirements. For
the latest information, see the
Steinberg web site below.
http://www.steinberg.net
• Are you recording or playing long
continuous sections of audio?
The audio data processing
capabilities of your computer will
depend on a number of factors
including CPU speed and access to
external devices. Reduce the audio
tracks then confirm the sound.
• Is a network adaptor for wired/
wireless LAN running?
Disable the suspected network
adaptor. Some network adaptors can
cause noise.
Noise Occurs When
Turning Off the Power, or
Settings are Not Saved to
the Device
• Is the power of the device turned
off by some means other than
using the power button?
Turn off the power of the device by
using the power button.
20
UR28M Getting Started
Appendix
Windows
English
Appendix
Remove the following two software
components.
Contents of the
Operation Manual
Introduction
Contents in this Operation Manual
Features
Panel Controls and Terminals (Details)
Rear Panel
Front Panel
Panel Controls for the Software Programs
Control Panel of the Audio Driver
dspMixFx UR28M
Dedicated Windows for Cubase Series
Sweet Spot Morphing Channel Strip
(Channel Strip)
REV-X
Usage Examples
Introduction
Recording with the Channel Strip and
REV-X
Controlling the Monitor Sound
Using the Device Without a Computer
• Yamaha Steinberg USB Driver
• Steinberg UR28M Applications
1. Turn off the computer.
2. Disconnect all USB devices
other than the mouse and
keyboard from the computer.
3. Start the computer and log on to
the Administrator account.
4. Open the window for the
uninstall operation as follows.
Windows XP:
[Start]  [Control Panel]  [Add or
Remove Programs]
Windows Vista/Windows 7:
[Start]  [Control Panel] 
[Uninstall a Program]
5. Select one of the software
components from the list.
Appendix
Glossary
Contents of the Getting Started Section
Signal Flow
Block Diagrams
Uninstalling TOOLS
for UR28M
Windows.................................page 21
Mac .........................................page 22
6. Uninstall them as follows.
Windows XP:
Click [Change/Remove]/[Remove].
Follow the on-screen instructions
to remove the software.
Windows Vista/Windows 7:
Click [Uninstall]/[Uninstall/
Change]. Follow the on-screen
instructions to remove the
software.
Uninstallation of TOOLS for UR28M is
now completed.
UR28M Getting Started
21
Appendix
English
Mac
dspMixFx UR28M
Remove the folders and files of the
following five software components.
[Applications]
dspMixFx_UR28M.app
• Yamaha Steinberg USB Driver
UR28M Extension
• dspMixFx UR28M
[Library]  [Application Support] 
[Steinberg]  [Components]
ur28m_extension.bundle
• UR28M Extension
• Sweet Spot Morphing Channel Strip
• REV-X
[Library]  [Receipts]
Steinberg UR28M Extension.pkg
Yamaha Steinberg USB Driver
Sweet Spot Morphing Channel Strip
[System]  [Library]  Extensions]
YamahaSteinbergUSBAudio.kext
[Library]  [Audio]  [Plug-Ins] 
[VST3]  [Steinberg]  [UR]
[Applications]  [Yamaha] 
[USBDriver]
Yamaha Steinberg USB Control Panel.app
UR-ChStrip_m.vst3
UR-ChStrip_s.vst3
UR28M-ChStrip_m.vst3
UR28M-ChStrip_s.vst3
[Library]  [PreferencePanes]
Yamaha Steinberg USB.prefPane
[Library]  [Preferences]
com.yamaha.YamahaSteinbergUSBDriver.
plist
[Library]  [Audio]  [MIDI Drivers]
YamahaSteinbergUSBMIDI.plugin
[Library]  [Audio]  [MIDI Devices] 
[Yamaha]  [Images]
USB_1500.tiff
USB_1502.tiff
USB_1503.tiff
[Library]  [Receipts]
YamahaSteinbergUSBAudioDriver.pkg
YamahaSteinbergUSBControlPanel.pkg
YamahaSteinbergUSBDriverplist.pkg
YamahaSteinbergUSBMIDIPlugIn.pkg
YamahaSteinbergUSBMIDIIcon.pkg
YamahaSteinbergUSBPrefPane.pkg
22
UR28M Getting Started
REV-X
[Library]  [Audio]  [Plug-Ins] 
[VST3]  [Steinberg]  [UR]
UR-REV-X_HALL.vst3
UR-REV-X_ROOM.vst3
UR-REV-X_PLATE.vst3
UR28M-REV-X_HALL.vst3
UR28M-REV-X_ROOM.vst3
UR28M-REV-X_PLATE.vst3
Uninstallation of TOOLS for UR28M is
now completed.
Appendix
English
Specifications
Technical Specifications
MIC/LINE INPUT 1/2 (Balanced)
Frequency Response
+0.1/-0.2dB, 20Hz to 22kHz
Dynamic Range
101dB, A-Weighted
THD+N
0.002%, 1kHz, -1dBFS, 22Hz/22kHz BPF
Crosstalk
>114dB, 1kHz
Maximum Input Level
+22dBu
Input Impedance
4k Ohm
Maximum Gain
60dB
Adjustable Gain
44dB
Pad
-26dB
HI-Z INPUT 1/2 (Unbalanced)
Maximum Input Level
+9.8dBV
Input Impedance
500k Ohm
LINE INPUT 3/4 (Balanced)
Frequency Response
+0.1/-0.1dB, 20Hz to 22kHz
Dynamic Range
102dB, A-Weighted
THD+N
0.001%, 1kHz, -1dBFS, 22Hz/22kHz BPF
Crosstalk
>110dB, 1kHz
Maximum Input Level
+16dBu (balanced)
+13.8dBV (unbalanced)
Input Impedance
20k Ohm (balanced)
10k Ohm (unbalanced)
2TR IN
Maximum Input Level
+3.5dBV
Input Impedance
10k Ohm
LINE OUTPUT A–C (Balanced)
Frequency Response
+0.1/-0.2dB, 20Hz to 22kHz
Dynamic Range
106dB, A-Weighted
UR28M Getting Started
23
Appendix
English
THD+N
0.001%, 1kHz, -1dBFS, 22Hz/22kHz BPF
Crosstalk
>129dB, 1kHz
Maximum Output Level
+16dBu
Output Impedance
75 Ohm
PHONES 1/2
Maximum Output Level
35mW+35mW, @40 Ohm
USB
Specification
USB2.0, 24bit, 44.1kHz/48kHz/88.2kHz/96kHz
XLR INPUT
Pin 1: Ground
Pin 2: Hot (+)
Pin 3: Cold (-)
Polarity
General Specifications
Power Requirements
8.4 W (PA-130)
Dimensions (H x D x W) 59 x 164 x 291 mm
Net Weight
1.4 kg
Operating Free-air
Temperature Range
0 to +40 °C
Included Accessories
AC power adaptor (PA-130 or equivalent)
Getting Started (this book)
ESSENTIAL PRODUCT LICENSE INFORMATION card
TOOLS for UR28M CD-ROM
Cubase AI DVD-ROM
USB cable
Specifications and descriptions in this manual are for information purposes only.
Steinberg/Yamaha Corp. reserves the right to change or modify products or
specifications at any time without prior notice. Since specifications, equipment or
options may not be the same in every locale, please check with your Steinberg/
Yamaha dealer.
Inrush Current based on EN 55103-1:2009
0.5A (on initial switch-on)
0.5A (after a supply interruption of 5s)
Conforms to Environments: E1, E2, E3 and E4
24
UR28M Getting Started
OBSERVERA!
Apparaten kopplas inte ur växelströmskällan (nätet) så länge som den
ar ansluten till vägguttaget, även om själva apparaten har stängts av.
ADVARSEL: Netspændingen til dette apparat er IKKE afbrudt,
sålænge netledningen sidder i en stikkontakt, som er tændt — også
selvom der er slukket på apparatets afbryder.
VAROITUS: Laitteen toisiopiiriin kytketty käyttökytkin ei irroita koko
laitetta verkosta.
(standby)
IMPORTANT NOTICE FOR THE UNITED KINGDOM
Connecting the Plug and Cord
IMPORTANT. The wires in this mains lead are coloured in accordance with the following code:
BLUE : NEUTRAL
BROWN : LIVE
As the colours of the wires in the mains lead of this apparatus may not correspond with the coloured makings
identifying the terminals in your plug proceed as follows:
The wire which is coloured BLUE must be connected to the terminal which is marked with the letter N or
coloured BLACK.
The wire which is coloured BROWN must be connected to the terminal which is marked with the letter L or
coloured RED.
Making sure that neither core is connected to the earth terminal of the three pin plug.
* This applies only to products distributed by Yamaha Music U.K. Ltd.
(2 wires)
Information for Users on Collection and Disposal of Old Equipment
This symbol on the products, packaging, and/or accompanying documents means that used electrical and electronic products
should not be mixed with general household waste.
For proper treatment, recovery and recycling of old products, please take them to applicable collection points, in accordance with
your national legislation and the Directives 2002/96/EC.
By disposing of these products correctly, you will help to save valuable resources and prevent any potential negative effects on
human health and the environment which could otherwise arise from inappropriate waste handling.
For more information about collection and recycling of old products, please contact your local municipality, your waste disposal
service or the point of sale where you purchased the items.
[For business users in the European Union]
If you wish to discard electrical and electronic equipment, please contact your dealer or supplier for further information.
[Information on Disposal in other Countries outside the European Union]
This symbol is only valid in the European Union. If you wish to discard these items, please contact your local authorities or dealer and ask for the
correct method of disposal.
Verbraucherinformation zur Sammlung und Entsorgung alter Elektrogeräte
Befindet sich dieses Symbol auf den Produkten, der Verpackung und/oder beiliegenden Unterlagen, so sollten benutzte elektrische
Geräte nicht mit dem normalen Haushaltsabfall entsorgt werden.
In Übereinstimmung mit Ihren nationalen Bestimmungen und den Richtlinien 2002/96/EC bringen Sie alte Geräte bitte zur
fachgerechten Entsorgung, Wiederaufbereitung und Wiederverwendung zu den entsprechenden Sammelstellen.
Durch die fachgerechte Entsorgung der Elektrogeräte helfen Sie, wertvolle Ressourcen zu schützen, und verhindern mögliche
negative Auswirkungen auf die menschliche Gesundheit und die Umwelt, die andernfalls durch unsachgerechte Müllentsorgung
auftreten könnten.
Für weitere Informationen zum Sammeln und Wiederaufbereiten alter Elektrogeräte kontaktieren Sie bitte Ihre örtliche Stadt- oder
Gemeindeverwaltung, Ihren Abfallentsorgungsdienst oder die Verkaufsstelle der Artikel.
[Information für geschäftliche Anwender in der Europäischen Union]
Wenn Sie Elektrogeräte ausrangieren möchten, kontaktieren Sie bitte Ihren Händler oder Zulieferer für weitere Informationen.
[Entsorgungsinformation für Länder außerhalb der Europäischen Union]
Dieses Symbol gilt nur innerhalb der Europäischen Union. Wenn Sie solche Artikel ausrangieren möchten, kontaktieren Sie bitte Ihre örtlichen
Behörden oder Ihren Händler und fragen Sie nach der sachgerechten Entsorgungsmethode.
Information concernant la Collecte et le Traitement des déchets d’équipements électriques et électroniques.
Le symbole sur les produits, l’emballage et/ou les documents joints signifie que les produits électriques ou électroniques usagés ne
doivent pas être mélangés avec les déchets domestiques habituels.
Pour un traitement, une récupération et un recyclage appropriés des déchets d’équipements électriques et électroniques, veuillez
les déposer aux points de collecte prévus à cet effet, conformément à la réglementation nationale et aux Directives 2002/96/EC.
En vous débarrassant correctement des déchets d’équipements électriques et électroniques, vous contribuerez à la sauvegarde
de précieuses ressources et à la prévention de potentiels effets négatifs sur la santé humaine qui pourraient advenir lors d’un
traitement inapproprié des déchets.
Pour plus d’informations à propos de la collecte et du recyclage des déchets d’équipements électriques et électroniques, veuillez
contacter votre municipalité, votre service de traitement des déchets ou le point de vente où vous avez acheté les produits.
[Pour les professionnels dans l'Union Européenne]
Si vous souhaitez vous débarrasser des déchets d’équipements électriques et électroniques veuillez contacter votre vendeur ou fournisseur pour
plus d’informations.
[Information sur le traitement dans d'autres pays en dehors de l'Union Européenne]
Ce symbole est seulement valable dans l'Union Européenne. Si vous souhaitez vous débarrasser de déchets d’équipements électriques et
électroniques, veuillez contacter les autorités locales ou votre fournisseur et demander la méthode de traitement appropriée.
Información para Usuarios sobre Recolección y Disposición de Equipamiento Viejo
Este símbolo en los productos, embalaje, y/o documentación que se acompañe significa que los productos electrónicos y eléctricos
usados no deben ser mezclados con desechos hogareños corrientes.
Para el tratamiento, recuperación y reciclado apropiado de los productos viejos, por favor llévelos a puntos de recolección
aplicables, de acuerdo a su legislación nacional y las directivas 2002/96/EC.
Al disponer de estos productos correctamente, ayudará a ahorrar recursos valiosos y a prevenir cualquier potencial efecto negativo
sobre la salud humana y el medio ambiente, el cual podría surgir de un inapropiado manejo de los desechos.
Para mayor información sobre recolección y reciclado de productos viejos, por favor contacte a su municipio local, su servicio de
gestión de residuos o el punto de venta en el cual usted adquirió los artículos.
[Para usuarios de negocios en la Unión Europea]
Si usted desea deshacerse de equipamiento eléctrico y electrónico, por favor contacte a su vendedor o proveedor para mayor información.
[Información sobre la Disposición en otros países fuera de la Unión Europea]
Este símbolo sólo es válido en la Unión Europea. Si desea deshacerse de estos artículos, por favor contacte a sus autoridades locales y pregunte
por el método correcto de disposición.
Informazioni per gli utenti sulla raccolta e lo smaltimento di vecchia attrezzatura
Questo simbolo sui prodotti, sull’imballaggio, e/o sui documenti che li accompagnano significa che i prodotti elettriche e elettroniche
non dovrebbero essere mischiati con i rifiuti domestici generici.
Per il trattamento, recupero e riciclaggio appropriati di vecchi prodotti, li porti, prego, ai punti di raccolta appropriati, in accordo con
la Sua legislazione nazionale e le direttive 2002/96/CE.
Smaltendo correttamente questi prodotti, Lei aiuterà a salvare risorse preziose e a prevenire alcuni potenziali effetti negativi sulla
salute umana e l’ambiente, che altrimenti potrebbero sorgere dal trattamento improprio dei rifiuti.
Per ulteriori informazioni sulla raccolta e il riciclaggio di vecchi prodotti, prego contatti la Sua amministrazione comunale locale, il
Suo servizio di smaltimento dei rifiuti o il punto vendita dove Lei ha acquistato gli articoli.
[Per utenti imprenditori dell’Unione europea]
Se Lei desidera disfarsi di attrezzatura elettrica ed elettronica, prego contatti il Suo rivenditore o fornitore per ulteriori informazioni.
[Informazioni sullo smaltimento negli altri Paesi al di fuori dell'Unione europea]
Questo simbolo è validi solamente nell’Unione europea. Se Lei desidera disfarsi di questi articoli, prego contatti le Sue autorità locali o il rivenditore
e richieda la corretta modalità di smaltimento.
►Warranty Terms and Conditions
available as printed PDF file at
www.steinberg.net/warranty
The Warranty Terms and Conditions available as printed PDF file at
www.steinberg.net/warranty apply only for countries of the European Economic Area
(EEA) and Switzerland.
►Gewährleistungsbestimmungen
finden Sie als druckbare PDF Datei unter
www.steinberg.de/warranty
Die Gewährleistungsbestimmungen in Schriftform sind als PDF-Datei unter
www.steinberg.de/warranty erhältlich und gelten nur für den Europäischen
Wirtschaftsraum (EWR) und die Schweiz.
►Les conditions de garantie
se trouvent dans le document PDF imprimable sous
www.steinberg.net/warranty
Les conditions de garantie disponibles au format PDF à la page www.steinberg.net/
warranty s’appliquent uniquement aux pays de l’Espace économique européen
(EEE) et à la Suisse.
►Las condiciones de garantía
se encuentran en el documento PDF en
www.steinberg.net/warranty
Los términos y condiciones de la garantía como archivo PDF para su impresión en
www.steinberg.net/ warranty sólo están disponible en países del Espacio Económico
Europeo (EEE) y Suiza.
►Termini e Condizioni di Garanzia
disponibili su file PDF stampabile all’indirizzo web
www.steinberg.net/warranty
I termini e le condizioni della garanzia, disponibili in formato PDF all’indirizzo
www.steinberg.net/warranty, sono validi soltanto per I paesi dell’Area Economica
Europea (EEA) e per la Svizzera.
If you need support or further product information please contact the distributor in
your country.
A list of distributors is available at this website:
http://www.steinberg.net/en/company/distributor.html
For assistance in determining who to contact, please contact “Headquarter SMTG.”
Wenn Sie Unterstützung oder weitere Produktinformationen benötigen, wenden Sie
sich bitte an den Vertrieb in Ihrem Land.
Eine Liste der Vertriebspartner finden Sie auf dieser Website:
http://www.steinberg.net/en/company/distributor.html
Wenn Sie Hilfe benötigen, an wen Sie sich wenden sollten, kontaktieren Sie bitte
„Headquarter SMTG“.
Pour toute demande d'assistance ou d’information supplémentaire sur les produits,
veuillez contacter le distributeur agréé dans votre pays.
La liste des distributeurs agréés est disponible sur le site Web suivant :
http://www.steinberg.net/en/company/distributor.html
Pour obtenir de l’aide sur les ressources à contacter, adressez-vous au « Siège de
SMTG ».
Para solicitar asistencia o más información sobre el producto, póngase en contacto
con el distribuidor de su país.
Encontrará una lista de distribuidores en el siguiente sitio web:
http://www.steinberg.net/en/company/distributor.html
Para consultas sobre el contacto adecuado, diríjase a “Headquarter SMTG.”
Per ottenere assistenza o avere ulteriori informazioni sul prodotto, contattare il
distributore locale.
L’elenco dei distributori è disponibile sul sito Web al seguente indirizzo:
http://www.steinberg.net/en/company/distributor.html
Per individuare il distributore da contattare, rivolgersi alla sede centrale SMTG.
如需更多支持和深层产品信息，请联系您所在国家的代理商。
代理商列表请浏览下列网址：
http://www.steinberg.net/en/company/distributor.html
如需帮助决定联系哪方代理商，请联系" SMTG总公司"。
HEAD OFFFICE
Steinberg Media Technologies GmbH
Frankenstraße 18b, 20097 Hamburg, Germany
Tel: +49-(0)40-210 35 0
Steinberg Web Site
http://www.steinberg.net
C.S.G., Pro Audio Division
© 2011 Yamaha Corporation
104MWAP*.*-01A0
WW71460

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project