IHP | (C)(GC)IR6PMA series | (C)(GC)IR30NTA/NMA series | Manual | pdf file

Add to My manuals
28 Pages

advertisement

IHP | (C)(GC)IR6PMA series | (C)(GC)IR30NTA/NMA series | Manual | pdf file | Manualzz

VENT-FREE INFRARED

GAS WALL HEATER

MODEL # Propane

(C)(GC)IR6PMA

(C)(GC)IR10PTA/PMA

(C)(GC)IR16PTA/PMA

(C)(GC)IR26PTA/PMA

Natural Gas

(C)(GC)IR6NMA

(C)(GC)IR10NTA/NMA

(C)(GC)IR18NTA/NMA

(C)(GC)IR30NTA/NMA

WARNING: This appliance is equipped for

(natural or propane) gas. Field conversion is not permitted.

ANS Z21.11.2-2013

Gas Fired Room Heaters

Volume II - Unvented Room Heaters

WARNING: IF THE INFORMATION IN THIS MANUAL IS NOT FOLLOWED

EXACTLY, A FIRE OR EXPLOSION MAY RESULT CAUSING PROPERTY

DAMAGE, PERSONAL INJURY OR LOSS OF LIFE.

- Do not store or use gasoline or other flammable vapors and Iiquids in vicinity of this or

any other appliance.

WHAT TO DO IF YOU SMELL GAS

• Do not try to light any appliance.

• Do not touch any electrical switch; do not use any phone in your building.

• Immediately call your gas supplier from a neighbor’s phone. Follow the gas supplier’s

instructions.

• If you cannot reach your gas supplier, call the fire department.

- Installation and service must be performed by a qualified installer, service agency or the

gas supplier.

This is an unvented gas-fired heater. It uses air (oxygen) from the room in which it is installed. Provisions for adequate combustion and ventilation air must be provided.

Refer to Air For Combustion and Ventilation section on page 8 of this manual.

INSTALLER: Leave this manual with the appliance.

CONSUMER: Retain this manual for future reference.

This appliance may be installed in an aftermarket, permanently located, manufactured (mobile) home, where not prohibited by local codes.

This appliance is only for use with the type of gas indicated on the rating plate.

This appliance is not convertible for use with other gases.

Questions, problems, missing parts? Before returning to your retailer, call our customer service department at 1-800-655-2008 or find us on the web at www.SuperiorFireplaces.US.com

1

IMIRI - 2014-06-23

TABLE OF CONTENTS

Important Safety Information ............................................................................................................3

Product Features .............................................................................................................................. 5

Air For Combustion and Ventilation .................................................................................................. 7

Installation ...................................................................................................................................... 10

Operation ........................................................................................................................................ 18

Care and Maintenance ................................................................................................................... 22

Troubleshooting .............................................................................................................................. 23

Replacement Parts ......................................................................................................................... 27

WARNING: Read the Installation & Operating Instructions before using this appliance.

IMPORTANT: Read all instructions and warnings carefully before starting installation.

Failure to follow these instructions may result in possible injury to persons or a fire hazard and will void the warranty.

PRODUCT SPECIFICATIONS

SERIES

MAX BTU

Fuel Type

6,000

Propane

(C)(GC)IR6PMA

Ignition

Electronic Push Button

Manifold Pressure

Inlet Gas Pressure

Fan Ratings (Select Models)

10 in. W.C.

Maximum

14 in. W.C.

*Minimum (*For purposes of input adjustment) 11 in. W.C.

Dimensions (in.)

( H x W x D) (Height includes legs)

Weight (lbs.)

19.8 in. x 17.0 in. x 8.9 in.

15.7

Not Available

(C)(GC)IR10PTA/PMA

12,000

Propane

Electronic Push Button

10 in. W.C.

14 in. W.C.

11 in. W.C.

19.8 in. x 17.0 in. x 8.9 in.

19.5

120V/60Hz,18W, 0.15A

SERIES

MAX BTU

Fuel Type

Ignition

(C)(GC)IR16PTA/PMA

18,000

Propane

Electronic Push Button

Manifold Pressure

Inlet Gas Pressure

10 in. W.C.

Maximum

14 in. W.C.

*Minimum (*For purposes of input adjustment) 11 in. W.C.

Dimensions (in.)

( H x W x D) (Height includes legs)

Weight (lbs.)

24.0 in. x 20.9 in. x 10.0 in.

23.7

Fan Ratings (Select Models)

120V/60Hz,18W, 0.15A

(C)(GC)IR26PTA/PMA

30,000

Propane

Electronic Push Button

10 in. W.C.

14 in. W.C.

11 in. W.C.

24.0 in. x 20.9 in. x 10.0 in.

30

120V/60Hz,18W, 0.15A

2

SERIES

MAX BTU

Fuel Type

Ignition

(C)(GC)IR6NMA

6,000

Natural Gas

Electronic Push Button

Manifold Pressure

Inlet Gas Pressure

Maximum

5 in. W.C.

14 in. W.C.

*Minimum (*For purposes of input adjustment) 6 in. W.C.

Dimensions (in.)

( H x W x D) (Height includes legs)

Weight (lbs.)

19.8 in. x 17.0 in. x 8.9 in.

15.7

Fan Ratings (Select Models)

Not Available

(C)(GC)IR10NTA/NMA

12,000

Natural Gas

Electronic Push Button

5 in. W.C.

14 in. W.C.

6 in. W.C.

19.8 in. x 17.0 in. x 8.9 in.

19.5

120V/60Hz,18W, 0.15A

SERIES

MAX BTU

Fuel Type

(C)(GC)IR18NTA/NMA

18,000

Natural Gas

Ignition

Manifold Pressure

Inlet Gas Pressure

Electronic Push Button

5 in. W.C.

Maximum

14 in. W.C.

*Minimum (*For purposes of input adjustment) 6 in. W.C.

Dimensions (in.)

( H x W x D) (Height includes legs)

Weight (lbs.)

24.0 in. x 20.9 in. x 10.0 in.

23.7

Fan Ratings (Select Models)

120V/60Hz,18W, 0.15A

(C)(GC)IR30NTA/NMA

30,000

Natural Gas

Electronic Push Button

5 in. W.C.

14 in. W.C.

6 in. W.C.

24.0 in. x 20.9 in. x 10.0 in.

30

120V/60Hz,18W, 0.15A

IMPORTANT SAFETY INFORMATION

IMPORTANT: Read this owner’s manual carefully and completely before trying to assemble, operate, or service this heater. Improper use of this heater can cause serious injury or death from burns, fire, explosion, electrical shock, and carbon monoxide poisoning.

3

IMPORTANT SAFETY INFORMATION

Installation and repair should be done by a qualified service person. The appliance should be inspected before use and at least annually by a professional service person. More frequent cleaning may be required due to excessive lint from carpeting, bedding material, etc. It is imperative that control compartments, burners and circulating air passageways of the

appliance be kept clean.

WARNING: Any change to this heater or its controls can be dangerous.

WARNING: Carefully supervise young children when they are in the room with the heater.

WARNING: Heater becomes very hot when operating. Children and adults should be alerted

to the hazard of high surface temperatures and should stay away to avoid burns or clothing

ignition Heater will remain hot for a time after shutoff. Allow surfaces to cool before touching.

WARNING: Make sure any panel, safety screen or guard removed for servicing an appliance

must be replaced prior to operating the heater

WARNING: Keep the appliance area clear and free from combustible materials, gasoline, and other flammable vapors and liquids.

WARNING: Do not place clothing or other flammable material on or near the appliance. Never place any objects on the heater.

WARNING: Due to high temperatures, locate this appliance out of traffic and away from

furniture and draperies.

This appliance is intended for supplemental heating.

CARBON MONOXIDE POISONING: Early signs of carbon monoxide poisoning resemble the flu with headaches, dizziness, or nausea. If you have these signs, the heater may not be working properly. Get fresh air immediately! Have heater serviced. Some people are more affected by carbon monoxide than others. These include pregnant women, people with heart or lung disease, people who are anemic, those under the influence of alcohol, and those living in high altitudes.

NATURAL AND PROPANE/LP GAS: Natural and Propane/LP gases are odorless. An odor-making agent is added to the gas. The odor helps you detect a gas leak. However, the odor added to the gas can fade. Gas may be present even though no odor exists. Make certain you read and understand all warnings. Keep this manual for reference. It is your guide to operating this heater safely.

WARNING: Do not use any accessories not approved for use with this heater.

CALIFORNIA PROPOSITION 65

Fuels used in gas or oil fired appliances and the products of combustion of such fuels contain chemicals known to the state of California to cause cancer, birth defects or other reproductive harm. This product contains chemicals, including lead and lead compounds, known to the state of

California to cause cancer, birth defects or other reproductive harm. Wash hands after handling.

4

SAFETY INFORMATION

1. Do not place Propane/LP supply tank(s) inside any structure. Place Propane/LP supply tank(s)

outdoors.

2. Only the IR6 Series can be installed in a bedroom or bathroom. When installing in a bedroom or

bathroom the heater MUST be mounted to the wall (See Wall Mounting, Page 13). All other

models cannot be installed in a bathroom or bedroom.

3. This heater needs fresh air ventilation to run properly. This heater has an Oxygen Depletion Sensing

(ODS) safety shutoff system. The ODS shuts down the heater if not enough fresh air is available.

See Air for Combustion and Ventilation, pages 7 through 9. If heater keeps shutting off, see

Troubleshooting, pages 23 through 26.

4. Keep all air openings in front, top and bottom of heater free of objects and debris to ensure

adequate air for proper combustion.

5. If heater shuts off, do not relight until you have provided fresh, outside air. If heater keeps shutting

off, have it serviced.

6. Do not run heater:

• Where flammable liquids or vapors are used or stored.

• Under dusty conditions.

7. Before using furniture polish, wax, carpet cleaner, or similar products, turn heater and pilot off. If

heated, the vapors from these products may create a white powder residue within burner box or

on adjacent walls or furniture.

8. Do not use heater if any part has been under water. Immediately call a qualified service technician

to inspect the room heater and to replace any part of the control system and any gas control

which has been under water.

9. Turn off and unplug heater and let cool before servicing. Only a qualified service person should

service and repair heater.

10. To prevent performance problems, do not use propane/LP fuel tank of less than 100 lbs. capacity.

11. WARNING: Do not allow fans to blow directly into the heater. Avoid any drafts that alter

burner flame patterns.

12. SAVE THESE INSTRUCTIONS.

5

PRODUCT FEATURES

SAFETY PILOT

This heater has a pilot with an Oxygen Depletion Sensing (ODS) safety shutoff system.

The ODS/pilot shuts off the heater if there is not enough fresh air and cuts off main burner gas in the event of flame out.

ELECTRONIC PUSH BUTTON IGNITION SYSTEM

This heater is equipped with an electronic push button ignition system. This system requires one AAA battery (provided).

LEG KIT

2 legs and 4 mounting screws are included for floor mounting the heater. See page 13.

PIEZO IGNITION SYSTEM (SELECT MODELS)

This heater is equipped with a piezo electric ignition system.

THERMOSTAT HEAT CONTROL(SELECT MODELS)

The control automatically cycles the burner on and off to maintain a desired room temperature. See page 24.

FAN KIT(SELECT MODELS)

The fan kit helps to distribute the warmed air into the space more rapidly.

State of Massachusetts: The installation must be made by a licensed plumber or gas fitter in

the Commonwealth of Massachusetts. Sellers of unvented propane or natural gas-fired

supplemental room heaters shall provide to each purchaser a copy of 527 CMR 30 upon sale

of the unit.

In the State of Massachusetts, unvented propane or natural gas-fired space heaters shall

be prohibited in bedrooms and bathrooms.

In the State of Massachusetts the gas cock must be a T-handle type. The State of

Massachusetts requires that a flexible appliance connector cannot exceed three feet

in length.

LOCAL CODES

Install and use heater with care. The installation must conform with local codes or, in the absence of local codes, with the latest edition of The Nation Fuel Gas Code, ANSI Z223.1/NFPA 54

*Available from:

American National Standard Institute, Inc.

1430 Broadway

New York, NY 10018

National Fire Protection Association, Inc.

1 Batterymarch Park

Quincy, MA 02269-9101

This heater is designed for vent-free operation. State and local codes in some areas prohibit, restrict and or have special requirements for vent-free heaters.

6

PREPARING FOR INSTALLATION

Before beginning assembly or operation of the product, make sure all parts are present.

Compare parts with package contents list. If any part is missing or damaged, do not attempt to assemble, install or operate the product. Contact customer service for replacement parts.

UNPACKING

1. Remove heater from carton.

2. Remove all protective packaging applied to heater for shipping

3. Verify all contents are present.

Expansion Bracket x 4 Expansion Bracket Screw

(ST4.8*15-16) x 4

Support Leg Screw

(M4*15) x 4

Wall Hanging

Spacer x 2

Wall Hanging

Spacer Screw

(M4*25) x 2

Wood Screw

(ST4.8*45-16) x 4

AAA Battery x 1 Expansion Bracket

Tool x 1

Support Leg x 2

4. Check heater for any shipping damage. If heater is damaged, promptly inform dealer where you

bought the heater.

WATER VAPOR: A BY-PRODUCT OF UNVENTED ROOM HEATERS

Water vapor is a by-product of gas combustion. An unvented room heater produces approximately one (1) ounce (30 mL) of water for every 1,000 BTUs (.3 Kw) of gas input per hour. An unvented room heater is intended as a supplemental heater rather than a primary heat source. In most supplemental heat applications, the water vapor does not create a problem.

In most applications, the water vapor enhances the low humidity atmosphere experienced during cold weather.

The following steps will help ensure that water vapor does not become a problem:

1. Be sure the heater is the proper size for the application, including adequate combustion air and

circulation air.

2. If there is high humidity, a dehumidifier may be used to help lower the water vapor content

of the air.

3. Do not use an unvented room heater as the primary heat source.

7

PREPARING FOR INSTALLATION

AIR FOR COMBUSTION AND VENTILATION

CAUTION: This heater shall not be installed in a room or space unless the required volume of indoor combustion air is provided by the method described in the National Fuel Gas Code, ANSI

Z223.1/NFPA54, the International Fuel Gas Code, or applicable local codes.

PRODUCING ADEQUATE VENTILATION

All spaces in homes fall into one of the three following ventilation classifications:

1. Unusually Tight Construction

2. Unconfined Space

3. Confined Space

The information on pages 7 through 9 will help you classify your space and provide adequate ventilation.

Confined and Unconfined Space

A confined space as a space whose volume is less than 50 cu. ft. per 1,000 BTU/hr (4.8 m^3 per kw) of the aggregate input rating of all appliances installed in that space and an unconfining space as a space whose volume is not less than 50 cu. ft. per 1,000 BTU/hr (4.8 m^3 per kw) of the aggregate input rating of all appliances installed in that space. Rooms connecting directly with the space in which the appliances are installed*, through openings not furnished with doors, are considered a part of the unconfined space.

This heater shall not be installed in a confined space or unusually tight construction unless provisions are provided for adequate combustion and ventilation air.

* Adjoining rooms are connecting only if there are doorless passageways or ventilation

grills between them.

Unusually Tight Construction

The air that leaks around doors and windows may provide enough fresh air for combustion and ventilation. However, in buildings of unusually tight construction, you must provide additional fresh air.

Unusually tight construction is defined as construction where: a) walls and ceilings exposed to the outside atmosphere have a continuous water vapor retarder

with a rating of one perm (6x10-11kg per pa-sec-m2) or less with openings gasketed or sealed

and b) weather stripping has been added on windows that can be opened and on doors and c) caulking or sealants are applied to areas such as joints around window and door frames,

between sole plates and floors, between wall-ceiling joints, between wall panels, at

penetrations for plumbing, electrical, and gas lines, and at other openings.

If your home meets all of the three criteria above, you must provide additional fresh air.

See “Ventilation Air From Outdoors” (page 9). If your home does not meet all of the three criteria above, proceed to “Determining Fresh-Air Flow For Heater Location”.

8

PREPARING FOR INSTALLATION

DETERMINING FRESH-AIR FLOW FOR HEATER LOCATION

Determining if You Have a Confined or Unconfined Space

Use this worksheet to determine if you have a confined or unconfined space.

Space: Includes the room in which you will install heater plus any adjoining rooms with doorless passageways or ventilation grills between the rooms.

1. Determine the volume of the space Length × Width × Height = cu. ft. (volume of space)

Example: Space size 20 ft. (length) × 16 ft.(width) × 8 ft. (ceiling height) = 2560 cu. ft. (volume

of space)

If additional ventilation to adjoining room is supplied with grills or openings, add the volume of these rooms to the total volume of the space.

2. Divide the space volume by 50 cu. ft. to determine the maximum BTU/hr the space can support.

_______ (volume of space) ÷ 50 cu. ft.= (Maximum BTU/hr the space can support)

Example: 2560 cu. ft. (volume of space) ÷ 50 cu. ft. = 51.2 or 51,200 (maximum BTU/hr the space

can support)

3. Add the BTU/hr of all fuel burning appliances in the space.

Vent-free heater _________ BTU/hr

Gas water heater* ________BTU/hr

Gas furnace _____________BTU/hr

Vented gas heater ________BTU/hr Example:

Gas heater logs __________BTU/hr Gas water heater 30,000 BTU/hr

Other gas appliances*+ ____BTU/hr Vent-free heater + 26,000 BTU/hr

Total = ____BTU/hr Total = 56,000 BTU/hr

*Do not include direct-vent gas appliances. Direct-vent draws combustion air from the

outdoors and vents to the outdoors.

4. Compare the maximum BTU/hr the space can support with the actual amount of BTU/hr used.

_______ BTU/hr (maximum the space can support)

_______ BTU/hr (actual amount of BTU/hr used).

Example : 51,200 BTU/hr (maximum the space can support) 56,000 BTU/hr (actual amount of

BTU/hr used)

The space in the above example is a confined space because the actual BTU/hr used is more than the maximum BTU/hr the space can support.

You must provide additional fresh air. Your options are as follows: a) Rework worksheet, adding the space of an adjoining room. If the extra space provides an

unconfined space, remove door to adjoining room or add ventilation grills between rooms. See

“Ventilation Air From Inside Building,” page 9.

b) Vent room directly to the outdoors. See “Ventilation Air From Outdoors”, page 9.

c) Install a lower BTU/hr heater if lower BTU/hr size makes room unconfined. If the actual BTU/hr

used is less than the maximum BTU/hr the space can support, the space is an unconfined space.

You will need no additional fresh air ventilation.

9

PREPARING FOR INSTALLATION

Ventilation Air From Inside Building

This fresh air would come from adjoining unconfined space. When ventilating to an adjoining unconfined space, you must provide two permanent openings: one within 12 in. of the wall connecting the two spaces (see options 1 and 2,

Fig. 1). You can also remove door into adjoining room (see option 3, Fig. 1).

Follow the National Fuel Gas Code

NFPA 54/ANS Z223.1. Air for Combustion and Ventilation for required size of ventilation grills or ducts.

Ventilation Air From Outdoors

Provide extra fresh air by using ventilation grills or duct. You must provide two permanent openings: one within 12 in. of the ceiling and one within 12 in. of the floor.

Connect these items directly to the outdoors or spaces open to the outdoors. These spaces include attics and crawl spaces.

Follow the National Fuel Gas Code NFPA

54/ANS Z223.1. Air for Combustion and

Ventilation for required size of ventilation grills or ducts.

IMPORTANT: Do not provide openings for inlet or outlet air into attic if attic has a thermostat-controlled power vent. Heated air entering the attic will activate the power vent. Rework worksheet, adding the space of the adjoining unconfined space. The combined spaces must have enough fresh air to supply all appliances in both spaces.

10

INSTALLATION

NOTICE: This heater is intended for use as supplemental heat. Use this heater along with your

primary heating system. Do not install this heater as your primary heat source.

WARNING: A qualified technician must install heater. Follow all local codes.

WARNING: Maintain the minimum clearances. If possible, provide greater clearances from the

floor, ceiling, and adjoining wall than required.

CAUTION: This heater creates warm air currents. These currents move heat to wall surfaces

next to heater. Installing heater next to vinyl or cloth wall coverings or operating heater where

impurities (such as tobacco smoke, candles, cleaning fluids, oil or kerosene lamps, etc.)

in the air exist, may cause walls to discolor.

CLEARANCES TO COMBUSTIBLES

Carefully follow the instructions below. This heater can be mounted on the wall or on the floor using the legs.

WARNING: Maintain the minimum clearances shown in (See Fig. 3). If you can, provide greater

clearances from floor, ceiling, and joining wall.

Fig. 3 - Mounting clearances as viewed from front of heater (inches)

8 in.

Minimum

From

Side of

Heater

CEILING

36 in.

Minimum

LEFT SIDE

RIGHT SIDE

36 in. Minimum from

Furniture and Draperies

FRONT

3 in. Minimum to Top Surface of Carpeting,

Tile or Other Combustible Material

FLOOR

*LEFT  /  RIGHT  

8  in.

*A Second Side Wall Must be at Least 18in.

Away from the Other Side of the Heater.

MINIMUM  CLEARANCE  TO  COMBUSTIBLES

TOP  

36  in.

BOTTOM

3  in.

FRONT

36  in.

Top  clearance  is  from  top  of  heater  to  ceiling,  wood  shelf  or  other  combustible  material

Bottom  clearance  is  from  bottom  of  heater  to  surface  of  carpet,  tile  or  other  combustible  material.

Rear

0  in.  to  Spacer

*A second side wall must be at least 18 in. away from the other side of the heater.

Always maintain a minimum of 36 in. clearance from furniture and draperies.

11

INSTALLATION

INSTALLING IGNITOR BATTERY

• Battery is included.

• Unscrew ignitor cap and insert included battery negative (flat)

side down (See Fig. 7). Replace Ignitor cap.

• Be sure to observe proper polarity (+/-) when installing or re-

placing the battery. Damage due to improper battery installa-

tion may void the warranty on the product.

• Install/replace the battery according to the type and quantity

stated in table below.

• Remove battery when depleted.

• For long periods of non-operation, remove the battery from all

components for safety.

WARNING: Do not use rechargable silver oxide cell batteries.

Component Type of Battery Battery Qty.

Ignitor AAA 1

Do NOT dispose of batteries in fire. Improper disposal may cause batteries to leak or explode.

INSTALLING FAN (OPTIONAL)

IMPORTANT: Optional fan is not approved for use in IR6 series wall heaters.

Fig. 7 - Installing Ignitor Battery

Fig. 8 - Fan Electric Supply

Grounded Three-Prong

Receptacle

WARNING: Electrical Grounding Instructions

This appliance is equipped with a three-prong (grounding) plug

for your protection against shock hazard and should be plugged

directly into a properly grounded three-prong receptacle.

1. Wall mounted heater must be disconnected from gas supply and

removed from wall before installing fan accessory. Contact a

qualified service person to do this.

2. Remove fan access panel by removing 4 panel screws using a

screwdriver (See Fig. 9). Attach Fan to the rear panel of the heater

using the four screws provided.

NOTE: Be sure the rocker switch is positioned in the upper right corner. (See Fig. 10).

3. This fan is equipped with manual “MAN” and automatic “AUTO”

settings (See Fig. 11 on page 13). Set the rocker switch to “MAN”

for manual mode, allowing the fan to continuously run until the

rocker switch is returned to the OFF “O” position. Set the rocker

switch to “AUTO” for the automatic mode, which will turn the fan on

and off based on ambient room temperature. It may take 5 to 10

minutes for the fan to come on when the unit is cold.

NOTE: If any of the original wire as supplied with the appliance must be replaced, it must be replaced with a wire of at least an equal temperature rating. Refer to Fig. 12 on page 13 for wiring diagram.

CAUTION: Label all wires prior to disconnection when servicing

controls. Wiring errors can cause improper and dangerous opera-

tion. Verify proper operation after servicing.

Fig. 9 - Knock-out Panel

Fig. 10 - Attaching Fan

Rocker Switch

12

Rocker Switch

INSTALLATION

Fig. 11 - Operating Fan

Fig. 12- Fan Wiring Diagram

Fan Switch

MAN AUTO

Fan Rocker

Switch

Thermo-switch

110/115

VAC

Black

White

Green

Fan

LOCATING HEATER

This heater is designed to be mounted on a wall or on a floor, using the legs included with the heater.

For convenience and efficiency, install heater:

1. Where there is easy access for operation,

inspection, and service.

2. In the coldest part of room.

3. A minimum of 3' away from furniture and draperies.

FLOOR MOUNTING (Cannot be done in bedroom or bathroom)

Before installing legs to heater base, please make sure you have the following items:

(2) Support Legs

(4) Support Leg Screws (M4*20)

1. Set back of heater on table with the bottom of heater

extending outside the table edge.

2. Fasten Legs to heater using Support Leg

Screws (Fig.13)

Note: If the heater is to be installed directly on carpeting, tile or other combustible material, other than wood flooring, the appliance shall be installed on a metal or wood panel extending the full width and depth of the appliance.

3. Once positioned, secure heater to the floor using screws and mounting holes found on Heater

Support Legs (See Fig. 14).

WALL MOUNTING

WARNING: Failure to position the parts in accordance with these diagrams or failure to use only parts specifically approved with this heater may result in property damage or personal injury.

Mounting Bracket

The mounting bracket is located on back panel of heater (See Fig. 15). It has been taped there for shipping. Remove mounting bracket from back panel.

13

Support Leg

Support Leg

Screw

Fig. 14 - Securing Support Leg

Support Leg

Fig. 15 - Mounting Bracket Location

Mounting Bracket

INSTALLATION

Methods For Attaching Mounting Bracket To Wall

Use only the last hole on each end of mounting bracket to attach bracket to wall. Attach mounting bracket to a wall only in one of two ways:

1. Attaching to wall stud: This method provides the strongest hold. Insert mounting screws through

mounting bracket and into wall studs.

2. Attaching to wall anchor: This method allows you to attach mounting bracket to hollow walls (wall

areas between studs) or to solid walls (concrete or masonry).

Decide which method better suits your needs. Either method will provide a secure hold for the mounting bracket.

Marking Screw Locations

1. Tape mounting bracket to wall where heater

will be located. Make sure mounting bracket

is level.

Fig. 16 - Mounting Bracket

Clearances (inches)

(GC)(C)IR6/12

2. Mark screw locations on wall (See Fig. 16).

Note: Mark only last hole on each end of

mounting bracket. Insert mounting

screws through these holes only.

3. Remove tape and mounting bracket

from wall.

Attaching Mounting Bracket To Wall

Note: Wall anchors, mounting screws, and spacers are in hardware package. The hardware package is provided with heater.

Attaching to Wall Stud Method

For attaching mounting bracket to wall studs:

(GC)(C)IR16/18/26/30

1. Drill holes at marked locations using

9/64-inch drill bit.

2. Place mounting bracket onto wall. Line up last hole

on each end of bracket with holes drilled in wall.

3. Insert mounting screws through bracket and into wall

studs.

4. Tighten screws until mounting bracket is firmly

fastened to wall studs.

5. Check that the bracket is secure before mounting

heater!

14

INSTALLATION

Attaching to Wall Anchor Method

For attaching mounting bracket to hollow walls (wall areas between studs) or solid walls (concrete or masonry):

1. Drill holes at marked locations using 5/16-inch drill bit.

For solid walls (concrete or masonry), drill at least

1 inch deep.

2. Fold wall anchor as shown in (See Fig. 17).

3. Insert wall anchor (wings first) into hole. Tap anchor

flush to wall.

4. For thin walls (1/2 inch or less), insert white key into wall

anchor. Push white key to “pop” open anchor wings

(See Fig. 18).

IMPORTANT: Do not hammer anchor key! For thick

walls (over 1/2 inch thick) or solid walls, do not pop

open wings.

5. Place mounting bracket onto wall. Line up last hole on

each end of bracket with wall anchors.

6. Insert mounting screws through bracket and into wall

anchors.

7. Tighten screws until mounting bracket is firmly fastened

to wall.

8. Check that the bracket is secure before mounting

heater!

Attaching Wall Hanging Spacers to Heater

WARNING: Failure to properly install the wall hanging

spacers may result in property damage, personal injury

or even death.

1. Locate spacer mounting holes on the lower right/left sections of the heater back panel.

2. Secure (2) Wall Hanging Spacers to heater back panel using (2) Spacer Screws ST4.8*45 (See Fig. 19a).

Placing Heater On Mounting Bracket

1. Locate two horizontal slots on back panel of heater.

2. Place heater onto mounting bracket. Slide horizontal

slots onto stand-out tabs on mounting bracket. Be sure

spacers rest evenly against wall (See Fig. 19b).

15

Fig. 17 - Folding Anchor

Fig. 18 - Popping Open Anchor

Wing For Thin Walls

Fig. 19a - Attaching Wall

Hanging Spacers to Heater

Fig. 19b - Mounting Heater

Onto Mounting Bracket

Horizontal Slots

Spacers

INSTALLATION

CONNECTING TO GAS SUPPLY

WARNING: A qualified service technician must connect heater to gas supply. Follow all local

codes.

the pressure regulator. Never connect the heater to private (non-utility) gas wells, commonly

known as wellhead gas.

WARNING: Do not overtighten gas connections.

CAUTION: Use only new, black iron or steel pipe. Internally tinned copper tubing may be used

in certain areas. Check your local codes. Use pipe of 1/2-in. diameter or greater to allow proper

gas volume to heater. If pipe is too small, undue loss of pressure will occur.

CAUTION: Check your gas line pressure before connecting heater to gas line. Gas line pressure

must be a minimum 6" WC for NG and 11" WC for LP with a max pressure of 14"WC. If gas line

pressure is higher, heater regulator damage could occur.

CAUTION: Never connect heater directly to an LP supply. This heater requires an external

regulator (not supplied). Install the external regulator between the heater and gas supply.

CAUTION: Avoid damage to regulator. Hold gas regulator with wrench when connecting into gas

piping and/or fittings.

CAUTION: Use pipe joint sealant that is resistant to gas (Propane or Natural Gas).

Typical Inlet Pipe Diameters

Use 3/8-inch black iron pipe or greater. Installation must include an equipment shutoff valve, union, and plugged 1/8-inch NPT tap.

Locate NPT tap within reach for test gauge hook up. NPT tap must be upstream from heater

(see Fig. 20).

IMPORTANT: Install an equipment shutoff valve in an accessible location. The equipment shutoff

valve is for turning on or shutting off the gas to the appliance.

Apply pipe joint sealant lightly to male threads. This will prevent excess sealant from going

into pipe. Excess sealant in pipe could result in clogged heater valves.

16

INSTALLATION

Install sediment trap in supply line as shown

(See Fig. 20). Place sediment trap where it is within reach for cleaning. Place sediment trap where trapped matter is not likely to freeze. A sediment trap traps moisture and contaminants.

This keeps them from going into heater controls.

If sediment trap is not installed or is installed wrong, heater may not run properly.

Fig. 20 - Gas Connection

CHECKING GAS CONNECTIONS

leaks immediately.

WARNING: Never use an open flame to check for a leak. Apply a 50/50 mixture of liquid soap and water to all joints. If bubbles form, there may be a leak. Correct all leaks immediately.

Pressure Testing Gas Supply Piping System

Test Pressures In Excess Of 1/2 PSIG ( 3.5kPa )

The appliance and its appliance main gas valve must be disconnected from the gas supply piping system during any pressure testing of that system at test pressures in excess of ½ psi (3.5 kPa).

Pressure Testing Gas Supply Equal To or less than

1/2 PSIG ( 3.5kPa )

The appliance must be isolated from the gas supply piping system by closing its equipment shut-off valve during any pressure testing of the gas supply piping system at test pressures equal to or less than

½ psi (3.5 kPa).

Leak Testing Heater Gas Internal Connections

1. Open equipment shutoff valve (See Fig. 21).

2. Make sure control knob of heater is in the OFF position.

3. Open gas supply tank valve (LP systems).

4. Check all joints from equipment shutoff valve to control

valve. Apply 50/50 mixture of

liquid soap and water to gas joints. If bubbles form, there

may be a leak.

5. Light heater (see Operation, page 18). Check all other

internal joints for leaks.

6. Turn off heater (see "To Turn Off Gas to Appliance,"

page 19).

Fig. 21 - Equipment Shut -off Valve

17

OPERATION

FOR YOUR SAFETY READ BEFORE LIGHTING

WARNING: If you do not follow these instructions exactly, a fire or explosion may result

causing property damage, personal injury or loss of life.

A. This appliance has a pilot which must be lighted using the electronic ignitor. When lighting the pilot,

follow these instructions exactly.

B. BEFORE LIGHTING smell all around the appliance area for gas. Be sure to smell next to the floor

because some gas is heavier than air and will settle on the floor.

WHAT TO DO IF YOU SMELL GAS

• Do not try to light any appliance.

• Do not touch any electrical switch; do not use any phone in your building.

• Immediately call your gas supplier from a neighbor’s phone. Follow the gas supplier’s instructions.

• If you cannot reach your gas supplier, call the fire department.

C. Use only your hand to push in or turn the gas control knob. Never use tools. If the knob will not

push in or turn by hand, don't try to repair it, call a qualified service technician. Forced or

attempted repair may result in a fire or explosion.

D. Do not use this appliance if any part has been under water. Immediately call a qualified service

technician to inspect the appliance and to replace any part of the control system and any gas

control, which has been under water.

LIGHTING INSTRUCTIONS

MANUAL GAS CONTROL

1. STOP! Read the safety information above on this page.

2. Turn off all electric power to the appliance.

3. Push in gas control knob slightly and turn clockwise to

OFF " " position. (See Fig. 22a)

NOTE: Knob cannot be turned from PILOT " " to OFF " " unless knob is pushed in slightly. Do not force.

4. Wait (5) minutes to clear out any gas. Then smell for gas, including

near the floor. If you smell gas, STOP! Follow “B” in the safety

information above. If you don’t smell gas, go to the next step.

5. Push in gas control knob slightly and turn counterclockwise to the

PILOT " " position. (See Fig. 23a) Depress control knob.

6. With control knob depressed, push down on the ignitor button until the

pilot lights. The pilot is visible, centered below the plaques, behind the

front grill. (See Fig. 24 on page 19)

7. Keep control depressed for (30) seconds after pilot lights. Release

control knob.

Fig. 22a

Note: If pilot goes out repeat steps 3 through 7. Wait (1) minute before attempting to light pilot again.

If after several tries the pilot still goes out, turn the gas control knob clockwise to the OFF " " position and call your service technician or gas supplier.

Fig. 23a

18

OPERATION

LIGHTING INSTRUCTIONS

If the control knob does not pop up when released, stop and immediately and call your service technician or gas supplier.

8. Turn on all electric power to the appliance.

9. Turn control knob counter clockwise to HIGH " " setting.

F

PI

LO

T

5

4

3

1

THERMOSTAT GAS CONTROL

1. STOP! Read the safety information on the previous page.

2. Turn off all electric power to the appliance.

3. Turn control knob clockwise to OFF " " position. (See Fig. 22b)

4. Wait (5) minutes to clear out any gas. Then smell for gas, including

near the floor. If you smell gas, STOP! Follow “B” in the safety

information above. If you don’t smell gas, go to the next step.

5. Turn knob counterclockwise to the PILOT " " position.

(See Fig. 23b) Depress control knob.

6. With control knob depressed, push down on the ignitor button until

the pilot lights. The pilot is visible centered below the plaques, behind

the front grill. (See Fig. 24)

7. Keep control depressed for (30) seconds after pilot lights. Release

control knob.

O

T

F

OF

Fig. 22b

5

1 2

4

Note: If pilot goes out repeat steps 3 through 7. Wait (1) minute before attempting to light pilot again. If after several tries the pilot still goes out, turn the gas control knob clockwise to the OFF " " position and call your service technician or gas supplier. If the control knob does not pop up when released, stop and immediately and call your service technician or gas supplier.

8. Turn on all electric power to the appliance.

9. Turn control knob counter clockwise to desired setting.

Fig. 23b

Fig. 24 - Pilot Flame Location

TO TURN OFF GAS TO APPLIANCE

1. Turn off all electric power to the appliance if service is to be performed.

2. Push in gas control knob slightly and turn clockwise to OFF " " position. DO NOT FORCE.

19

OPERATION

THERMOSTATIC CONTROL OPERATION (SELECT MODELS)

The thermostat used on this heater senses the room temperature. At times the room may exceed the set temperature. If so, the burner will shut off. The burner will cycle back on when room temperature drops below the set temperature. The control knob can be set to any comfort level between "HIGH" (5) and

"LOW"(1) (See Fig. 25).

MANUAL CONTROL OPERATION

Manual valves remain burning in the HIGH " " setting until manually turned to OFF " "(See Fig. 25).

Thermostatic

1

3

4

5

O

T

ILO

Manual

Fig. 25 - Control

Knob Position

INSPECTING BURNERS

Check pilot flame pattern daily when in use and at least yearly by a qualified service agency.

PILOT FLAME PATTERN

Fig. 26 shows a correct pilot flame pattern. Fig. 27 shows an incorrect pilot flame pattern. The incorrect pilot flame is not touching the thermocouple. This will cause the thermocouple to cool, which shuts the heater off. If pilot flame pattern is incorrect:

• turn heater off (see “To Turn Off Gas to Appliance” on page 19)

• see Troubleshooting pages 23 through 26.

Fig. 26 - Correct Pilot Flame Pattern Fig. 27 - Incorrect Pilot Flame Pattern

WARNING: If yellow tipping occurs, your heater could produce increased levels of carbon

monoxide. If burner flame pattern shows yellow tipping, follow instructions under BURNER FLAME

PATTERN, page 21.

Notice: Do not mistake orange flames with yellow tipping. Dirt or other fine particles enter the heater and burn causing brief patches of orange flame.

20

OPERATION

BURNER FLAME PATTERN

Fig. 28 shows a correct burner flame pattern. Fig. 29 shows an incorrect burner flame pattern with lifting, and excessive flame height.

If burner flame is incorrect:

• turn heater off (see “To Turn Off Gas to Appliance”, page 19).

• see Troubleshooting, pages 23 through 26.

Fig. 28 - Correct Flame Pattern with

Control Knob Set to High Flame

Fig. 29 - Incorrect Flame Pattern with

Control Knob Set to High Flame

21

CARE AND MAINTENANCE

NOTE: Before servicing you will need to remove the front panel of the heater. There are 4 Philips head screws, 2 on the left side and 2 on the right, securing the front panel to the heater (See Fig. 30). Always allow the unit to cool for at least thirty minutes before attempting to remove the front panel.

Fig. 30 - Front Panel Removal

WARNING: Turn off heater, unplug electrical cord and let cool

before servicing.

CAUTION: You must keep control areas, burner, and circulating air

passageways of heater clean. Inspect these areas of heater before

each use. Have heater inspected yearly by a qualified service

person. Heater may need more frequent cleaning due to excessive

lint from carpeting, bedding material, pet hair, etc.

WARNING: Failure to keep the primary air opening(s) of the burner(s) clean may result in sooting

and propery damage.

CLEANING ODS/PILOT AND BURNER

Use a vacuum cleaner, pressurized air, or a small, soft bristled brush to clean tile face, orifice and primary burner. Look into burner opening and ensure that it is clean.

CLEANING BURNER PILOT AIR INLET HOLE

We recommend that you clean the unit every three months or after 2,500 hours of operation. We also recommend that you keep the burner tube and pilot assembly clean and free of dust and dirt. To clean these parts we recommend using compressed air no greater than 30 PSI. You can use a vacuum cleaner in the blow position. If using compressed air in a can, please follow the directions on the can.

If you don't follow directions on the can, you could damage the pilot assembly.

CAUTION: Never use a wire, needle, or similar object to clean ODS/pilot. This can damage ODS/ pilot unit.

1. Shut off the unit, including the pilot. Allow the unit to cool for at least thirty minutes.

2. Remove 4 screws - 2 screws on each side of the front panel.

3. Pull front panel forward.

4. Blow air through the ports/slots and holes in the burner. Also clean the pilot assembly. A yellow

tip on the pilot flame indicates dust and dirt in the pilot assembly. There is a small pilot air inlet hole

about two inches from where the pilot flame comes out of the pilot assembly (see Fig. 26 & 27 on

page 20). With the unit off, lightly blow air through the air inlet hole. You may blow through a

drinking straw if air is not available.

5. Replace front panel when completed, using the screws removed.

CLEANING CABINET AIR PASSAGEWAYS

Use a vacuum cleaner or pressurized air to clean.

CLEANING FAN (SELECT MODELS)

Carefully use a vacuum cleaner or compressed air to keep fan compartment and blades free of dust and debris.

NOTE: The fan motor is pre-lubricated for extended bearing life and requires no further lubrication.

CLEANING EXTERIOR

Use a soft cloth dampened with a mild soap and water mixture.

Wipe the cabinet to remove dust.

22

TROUBLESHOOTING

• Shut off gas supply.

• Do not try to light any appliance.

• Do not touch any electrical switch; do not use any phone in your building.

• Immediately call your gas supplier from a neighbor’s phone. Follow the gas supplier’s instructions.

• If you cannot reach your gas supplier, call the fire department.

IMPORTANT: Operating heater where impurities in air exist may create odors. Cleaning supplies, paint, paint remover, cigarette smoke, cements and glues, new carpet or textiles, etc., create fumes.

These fumes may mix with combustion air and create odors.

WARNING: Turn off and let cool before servicing. Only a qualified service person should service

and repair heater.

PROBLEM POSSIBLE CAUSE

When ignitor button is pressed in, there is no spark at ODS/ pilot.

Unit shuts off after running a few minutes.

1. Ignitor electrode is

positioned wrong.

2. Ignitor electrode is broken.

3. Ignitor electrode is not

connected to ignitor cable.

4. Ignitor cable is pinched or wet.

5. Damaged ignitor cable.

6. Bad piezo ignitor or ignition module.

7. Bad battery.

1. Gas supply is turned off or

equipment shutoff valve is

closed.

2. Control knob not fully

pressed in while pressing

ignitor button.

3. Air in gas lines when

installed.

4. ODS / pilot is clogged.

5. Control knob not in PILOT position.

6. Depleted gas supply (propane)

CORRECTIVE ACTION

1. Replace ODS.

2. Replace ODS.

3. Replace ignitor cable

4. Free ignitor cable if pinched by any metal or tubing. Keep ignitor cable dry.

5. Replace ignitor cable.

6. Replace piezo ignitor or ignition module.

7. Replace the battery.

1. Turn on gas supply or open equipment shutoff valve.

2. Fully press in control knob while

pressing ignitor button.

3. Continue holding down control knob.

Repeat igniting operation until air is

removed.

4. Clean ODS/pilot (see Care and

Maintenance, page 21) or replace

ODS/pilot assembly.

5. Turn control knob to PILOT position.

6. Contact local propane/LP gas company.

23

TROUBLESHOOTING

PROBLEM POSSIBLE CAUSE

ODS/pilot lights but flame goes out when control knob is released.

1. Control knob is not fully

pressed in.

2. Control knob is not pressed

in long enough.

3. Equipment shutoff valve is

not fully open.

4. Thermocouple connection is

loose.

5. Thermocouple damaged.

6. Control valve damaged.

7. Bad thermal switch.

Burner(s) does not light afterODS/pilot is lit.

1. Thermostat setting too low.

2. Burner orifice is clogged.

3. Burner orifice diameter is

too small.

4. Inlet gas pressure is too low.

Delayed ignition of burner(s).

Burner backfiring during combustion.

High yellow flame during burner combustion

1. Manifold pressure is too low.

2. Burner orifice is clogged.

1. Burner orifice is clogged or

damaged.

2. Burner is damaged.

3. Gas regulator is damaged.

1. Not enough air.

2. Gas regulator is defective.

CORRECTIVE ACTION

1. Press in control knob fully.

2. After ODS/pilot lights, keep control

knob pressed in 30-60 seconds.

3. Fully open equipment shutoff valve.

4. Hand tighten until snug, and then

tighten ¼ turn more.

5. Replace thermocouple.

6. Contact customer service.

7. Replace thermal switch.

1. Turn thermostat knob to a higher setting.

2. Clean burner orifice (see Care and

Maintenance, page 21) or contact

customer service.

3. Contact customer service.

4. Contact your gas supplier.

1. Contact your gas supplier.

2. Clean burner (see Care and Maintenance, page 21) or contact customer

service.

1. Clean burner orifice (see Care and

Maintenance, page 21 or contact

customer service.

2. Contact dealer or customer service.

3. Replace gas regulator.

1. Check burner for dirt and debris. If found, clean burner (see Care and Maintenance, page 21).

2. Replace gas regulator.

Gas odor during combustion.

1. Foreign matter between control valve and burner.

2. Gas leak. (See Warning

Statement at top of page 23).

Heater produces a clicking/ticking noise just after burner is lit or shut off.

1. Metal is expanding while

heating or contracting

while cooling.

1. Take apart gas tubing and remove foreign matter.

2. Locate and correct all leaks (see “Checking Gas Connections,” page 17).

1. This is common with most heaters. If noise is excessive, contact qualified

service technician.

24

TROUBLESHOOTING

PROBLEM

White powder residue forming within burner box or on adjacent walls or furniture.

Heater produces unwanted odors.

POSSIBLE CAUSE

1. When heated, the vapors from furniture polish, wax, carpet cleaners, etc., turn into white powder residue.

1. Heater is burning vapors

from paint, hair spray, glues, etc. See IMPORTANT statement, page 22.

2. Gas leak. See Warning

Statement, page 23.

3. Low fuel supply.

CORRECTIVE ACTION

1. Turn heater off when using furniture

polish, wax, carpet cleaner or similar products.

1. Ventilate room. Stop using odor

causing products while heater is

running.

2. Locate and correct all leaks (see

“Checking Gas Connections,” page 17).

3. Refill supply tank (Propane /LP models).

Heater shuts off in use (ODS operates).

1. Not enough fresh air is

available.

2. Low line pressure.

3. ODS/pilot is partially

clogged.

Gas odor exists even when control knob is in OFF position.

1. Gas leak. See Warning

Statement at top of page 22.

2. Control valve is

defective.

1. Open window and/or door for

ventilation.

2. Contact local gas supplier.

3. Clean ODS/pilot (see Care and

Maintenance, page 22).

1. Locate and correct all leaks (see

“Checking Gas Connections”, page 17).

2. Contact customer service.

1. Not enough combustion/

ventilation air.

1. Refer to “Air for Combustion and

Ventilation” requirements, page 7.

Moisture/condensation noticed on windows.

Slight smoke or odor during initial operation

Heater produces a whistling noise when burner is lit.

1. Residues from

manufacturing process.

1. Turning control knob to high (5) position when burner is cold.

2. Air in gas line.

3. Air passageways on

heater are blocked.

4. Dirty or partially clogged

burner orifice.

1. Problem will stop after a few hours of operation.

1. Turn control knob to low (1) position and let warm up for a minute.

2. Operate burner until air is removed from line. Have gas line checked by local

propane/LP gas company.

3. Observe minimum installation

clearances (Fig. 3, page 10)

4. Clean burner (see Care and Maintenance, page 22) or contact customer service.

25

TROUBLESHOOTING

PROBLEM

Fan is not spinning.

POSSIBLE CAUSE

1. There is no power to the fan.

2. Fan is set to "AUTO".

Fan is making a loud noise.

3. Fan motor is bad.

1. Fan housing or blades

are dirty.

2. Fan rotation is blocked.

3. Defective fan.

CORRECTIVE ACTION

1. Verify fan is plugged in and set to "MAN" or "AUTO".

2. Allow 5-10 minutes for fan to engage.

3. Replace fan.

1. See "Cleaning Fan", page 22.

2. Verify wiring is not in fan path.

3. Replace fan.

26

REPLACEMENT PARTS LIST

For replacement parts, call our customer service department at 1-800-655-2008.

WARNING: Only use genuine replacement parts from Innovative Hearth Products. Using any

parts other than the original replacement parts may result in property damage, personal injury or

even death.

13

4

10

11

5

6

14

2

7

3

8

1

12

9

ITEM

No.

DESCRIPTION

10

11

12

13

7

8-1

8-2

9

3-1

3-2

4

5

6

1

2

3

Front Panel

Burner Assembly

ODS Assembly (Complete)

ODS - (LP) Propane Pilot

ODS - (NG) Natural Gas Pilot

ODS Connector Wire

Thermostatic Gas Valve

Manual Gas Valve

Overheat Limit Switch

NG Regulator Assembly

LP Regulator Assembly

Front Grille

Wall Mounting Bracket

Ignitor Module

Support Leg

Ignitor Bracket

14

15

Fan Assembly (Select Models)

Hardware Pack

16-1

Replacement Orifice (LP)

16-2

Replacement Orifice (NG)

* Item/version not shown in exploded parts diagram

QTY

1

1

1

2

1

1

1

1

1

1

1

1

1

1

1

1

1

1

1

IR6P/6N Series

AQ000090

AQ000098*

AQ000031

AQ000028

AQ000110

AQ000025

AQ000112

AQ000042

AQ000073

AQ000073A

AQ000099

AQ000108

AQ000045

AQ000038

AQ000019

N/A

AQ000233*

AQ000201*

AQ000200*

Manufactured For Innovative Hearth Products, 1508 Elm Hill Pike,

Suite 108, Nashville, TN 37210 by GHP Group, Inc., Niles, IL

27

PART NUMBER

IR10P/10N Series IR16P/18N Series

AQ000090

AQ000137

AQ000060*

AQ000065*

AQ000031

AQ000028

AQ000110

AQ000025

AQ000112

AQ000042

AQ000073

AQ000073A

AQ000099

AQ000108

AQ000045

AQ000038

AQ000019

AQ000232

AQ000233*

AQ000203*

AQ000202*

AQ000031

AQ000028

AQ000052

AQ000025

AQ000112

AQ000042

AQ000073

AQ000073A

AQ000063*

AQ000006*

AQ000045

AQ000038

AQ000019

AQ000232

AQ000233*

AQ000205*

AQ000204*

IR26P/30N Series

AQ000001*

AQ000022*

AQ000031

AQ000028

AQ000052

AQ000025

AQ000112

AQ000042

AQ000073

AQ000073A

AQ000023*

AQ000006*

AQ000045

AQ000038

AQ000019

AQ000232

AQ000233*

AQ000199*

AQ000198*

Printed in China

advertisement

Related manuals

advertisement