Air Techniques AirStar 12 Owner's Manual

Air Techniques AirStar 12: The AirStar 12 is a high-speed, 12-inch diamond saw designed for cutting a wide range of materials, including ceramic, porcelain, natural stone, and glass. It features a powerful 1.5 horsepower motor, a durable steel frame, and a water tray to keep dust and debris under control. The AirStar 12 is ideal for cutting tiles, countertops, and other large materials.

PDF

Document

A C A D I A

Acadia

Amalgam Separator

Part Number: A1250

Pre-Installation Guide

Important: The Separator is only installed between the treatment operatory and the vacuum system input. DO NOT connect the unit to the outlet of any separation tank (dry vacuum system) or liquid ring pump (wet vacuum system).

Introduction

As shown below, a Separator is installed onto either an existing or new dry pump or liquid ring pump vacuum system. The unit is only installed between the treatment operatory output and the vacuum system input. This new installation or modification is to be performed by authorized service personnel using similar quality connection hoses and fittings. All installations must conform to local codes and meet all local, state and/or federal environmental laws and regulations.

ACADIA Separator

Input Connection

Any

Water Ring

Pump

Treatment

Operatory OR

ACADIA Separator

Output Connection

Air/Water

Separation

Tank

AND

Any Dry

Vacuum

Pump

Typical Acadia Amalgam Separator Installation Configurations

52.3 cm

(21 in)

37.4 cm

(15 in)

1-1/2" Barb Adaptor

Input from

ACADIA Separator

1-1/2" Hose

Clamps

Adapter 1-1/2" Slip

X 1-1/2" FNPT

1-1/2" Piping from

Treatment Operatory

Adapter 1-1/2" NPT

X 1-1/2" Barb

1-1/2"

Hose

ACADIA

Separator

Input Port

68.3 cm

(27 in)

Acadia Input Port Connection to Operatory Vacuum Line

ACADIA Weight (empty): 6.80 kg (15 lbs)

Acadia Dimension Drawing

24"

12"

Floor Drain

20"

Acadia Floor

Installation

18"

12"

Single or Dual

VacStar Pump or CAS Tank

INSTALLATION NOTES

A. VACUUM SYSTEM INSTALLATION SPACE -

Area used for wet pump installation for VacStar systems.

Area used for CAS tank installation for STS systems.

Note: Refer to Pre-Installation Guide for specific vacuum system being installed.

B. VACUUM LINE - Recommended sub-floor plumbing vacuum line connection between the operatory and utility room terminated with an 1-1/2 inch FNPT connector. Connect to Acadia input port via supplied 6-foot hose, connectors and hardware.

C. ACADIA WALL INSTALLATION - Locate the Acadia on the wall so the input and output of ports of the unit are within 4 feet of vacuum line connection (B.) and vacuum system input (E.) respectively.

D. ACADIA FLOOR INSTALLATION Locate the Acadia on the floor so the input and output of ports of the unit are within 4 feet of vacuum line connection (B.) and vacuum system input (E.).

Use Foot installation Kit, P/N A1399.

E. VACUUM SYSTEM INPUT - Acadia output line connection to the applicable vacuum system. Connect Acadia output port via 6-foot hose, connectors and hardware supplied with the vacuum system.

F. ELECTRICAL RECEPTACLE - Necessary when using a 12VDC power supply to power the optional Acadia Alert Monitor Module.

Note: Refer to Pre-Installation Guide for specific electrical requirements of the vacuum system being installed.

Typical Acadia Amalgam Separator Utility Room Installation Layout Details

Notes:

1. Bushing used depends on pump installation:

Use 1-1/2 in. SPG X 1 in. FNPT for dual VacStar pumps.

Use 1-1/2 in. SPG X 3/4 in. FNPT for a single VacStar pump.

1-1/2 inch

Barb Adaptor Output from ACADIA Separator

Reducing Bushing.

See Note 1.

Hose & Fittings Provided with VacStar Pump.

See Note 2.

1-1/2 inch Connector

Flexible Coupling with

Hose Clamps

See Detail

See

Detail

Single Pump VacStar

Air Vent

2. Dual pump installations use 1 inch hose and fittings, while single pump installations use 3/4 inch hose and fittings.

VACSTAR

INPUT FILTER

Single and Dual Pump VacStar Connection Detail Dual Pump VacStar

Acadia Connection to a VacStar System (Direct pump connection. No Separation Tank.)

Floor

Drain

Floor

Drain

1-1/2" Barb Adaptor

Output from

ACADIA Separator

Tank Input Port

1-1/2 inch Hose

See

Detail

Adapter 1-1/2" NPT

X 1-1/2" Barb

Floor Drain

CAS

SEPARATION TANK

STS Vacuum

Pump

CAS Tank Connection Detail CAS Tank Stacked on STS Pump

Acadia Connection to a STS Pump/CAS Tank Vacuum System (Direct connection to Separation Tank.)

Corporate Headquarters

1295 Walt Whitman Road | Melville, New York 11747- 3062 | Phone: 800-247-8324 | Fax: 888-247-8481

Website: www.airtechniques.com

Hello! I am an AI chatbot specifically trained to assist you with the Air Techniques AirStar 12 Owner's manual. I have thoroughly reviewed the document and can help you locate the exact information you need or explain the content in clear and simple terms. Whether you’re looking for guidance on specific features, troubleshooting steps, or general usage, feel free to ask your questions. The more details you provide about your concerns or needs, the more accurately and effectively I can assist you!