Advertisement
Advertisement
Copyright
Copyright
2014 by PLANET Technology Corp. All rights reserved. No part of this publication may be reproduced, transmitted, transcribed, stored in a retrieval system, or translated into any language or computer language, in any form or by any means, electronic, mechanical, magnetic, optical, chemical, manual or otherwise, without the prior written permission of PLANET.
PLANET makes no representations or warranties, either expressed or implied, with respect to the contents hereof and specifically disclaims any warranties, merchantability or fitness for any particular purpose. Any software described in this manual is sold or licensed "as is". Should the programs prove defective following their purchase, the buyer (and not PLANET, its distributor, or its dealer) assumes the entire cost of all necessary servicing, repair, and any incidental or consequential damages resulting from any defect in the software. Further, PLANET reserves the right to revise this publication and to make changes from time to time in the contents hereof without obligation to notify any person of such revision or changes.
All brand and product names mentioned in this manual are trademarks and/or registered trademarks of their respective holders.
Federal Communication Commission Interference Statement
This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:
1. Reorient or relocate the receiving antenna.
2. Increase the separation between the equipment and receiver.
3. Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
4. Consult the dealer or an experienced radio technician for help.
FCC Caution
To assure continued compliance, use only shielded interface cables when connecting to computer or peripheral devices. Any changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment.
This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions:
(1) This device may not cause harmful interference
(2) This Device must accept any interference received, including interference that may cause undesired operation.
Any changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment.
I
Federal Communication Commission (FCC) Radiation Exposure Statement
This equipment complies with FCC radiation exposure set forth for an uncontrolled environment. In order to avoid the possibility of exceeding the FCC radio frequency exposure limits, human proximity to the antenna shall not be less than 20 cm (8 inches) during normal operation.
R&TTE Compliance Statement
This equipment complies with all the requirements of DIRECTIVE 1999/5/CE OF THE EUROPEAN
PARLIAMENT AND THE COUNCIL OF 9 March 1999 on radio equipment and telecommunication terminal Equipment and the mutual recognition of their conformity (R&TTE). The R&TTE Directive repeals and replaces in the directive 98/13/EEC (Telecommunications Terminal Equipment and
Satellite Earth Station Equipment) as of April 8, 2000.
Safety
This equipment is designed with the utmost care for the safety of those who install and use it.
However, special attention must be paid to the dangers of electric shock and static electricity when working with electrical equipment. All guidelines of this and of the computer manufacture must therefore be allowed at all times to ensure the safe use of the equipment.
National Restrictions
This device is intended for home and office use in all EU countries (and other countries following the EU directive 1999/5/EC) without any limitation except for the countries mentioned below:
Country Restriction Reasons/remarks
Bulgaria None
France
General authorization required for outdoor use and public service
Outdoor use; limited to 10 mW e.i.r.p. within the band
Military Radiolocation use. Refarming of the 2.4 GHz band has been ongoing in recent years to allow current
2454-2483.5 MHz relaxed regulation. Full implementation planned 2012
Italy None
Luxembourg None
Norway Implemented
Russian
Federation
None
If used outside of own premises, general authorization is required
General authorization required for network and service supply(not for spectrum)
This subsection does not apply for the geographical area within a radius of 20 km from the centre of Ny-Ålesund
Only for indoor applications
Note: Please don’t use the product outdoors in France.
WEEE regulation
To avoid the potential effects on the environment and human health as a result of the presence of hazardous substances in electrical and electronic equipment, end users of electrical and electronic equipment should understand the meaning of the crossed-out wheeled bin symbol. Do not dispose of WEEE as unsorted municipal waste and have to collect such WEEE separately.
II
Revision
User Manual for PLANET 1200Mbps 11ac Dual Band Ceiling Mount Wireless Access Point
Model: WDAP-C7200AC
Rev: 1.0 (May, 2014)
Part No. EM-WDAP-C7200AC_v1.0 (2080-E11010-000)
III
CONTENTS
IV
V
FIGURE
..................................................................................10
......................................................................................... 11
1..........................................................................12
2..........................................................................13
3..........................................................................13
4..........................................................................14
4..........................................................................14
...............................................................................17
.......................................................................................18
..............................................................................................19
........................................................................................21
.........................................................................................21
...............................................................................................21
.................................................................................................22
.........................................................................22
........................................................................23
..............................................................23
............................................................24
....................................................................24
...................................................................25
.........................................................25
.........................................................26
..................................................................................................26
..............................................................................................29
AP ............................................................................30
AP ...............................................................32
-1 ...........................................................................................34
-2 ...........................................................................................35
-3 ...........................................................................................35
-4 ...........................................................................................35
-5 ...........................................................................................36
........................................................................37
VI
– WDS...........................................................................42
– WDS+AP....................................................................44
.............................................................................46
...............................................................................................48
..............................................................................49
.................................................................................50
..................................................................................51
...........................................................................................60
– AP ...........................................................................61
AP ............................................................63
-1 ........................................................................................65
-2 ........................................................................................65
-3 ........................................................................................66
-4 ........................................................................................66
-5 ........................................................................................66
.....................................................................68
– WDS........................................................................73
– WDS+AP.................................................................75
..........................................................................77
............................................................................................79
...........................................................................80
..............................................................................82
..................................................................................83
..................................................................................................85
VII
...............................................................................................92
...........................................................................................97
.........................................................................103
...........................................................................................103
....................................................................104
...............................................................................................106
................................................................................................107
................................................................................................108
IGHLIGHT AND SELECT THE WIRELESS NETWORK
...............................................................108
..........................................................................................109
................................................................................. 110
..................................................................................... 111
.................................................................................... 113
...................................................................................... 114
.......................................................................... 114
VIII
User Manual of WDAP-C7200AC
Chapter 1. Product Introduction
1.1 Package Contents
Thank you for choosing PLANET WDAP-C7200AC. Before installing the AP, please verify the contents inside the package box.
WDAP-C7200AC Quick Guide CD-ROM
(User Manual included)
Quick Guide Mounting Kit
If there is any item missing or damaged, please contact the seller immediately.
-1-
User Manual of WDAP-C7200AC
1.2 Product Description
Ceiling Mount Designed for Highly-efficient Wireless Coverage
Featuring attractive flying saucer appearance and ceiling-mount design, the WDAP-C7200AC can be firmly installed on the ceiling or the wall conveniently. The ceiling-mount design is smartly integrated into the environment. Its streamlined body without the protruding antennas also gives effects of embellishment in the surroundings. Moreover, the WDAP-C7200AC is compliant with the IEEE 802.3at PoE standard, so it is easy and flexible in client-side installation. It is definitely nice to have this eye-catching access point mount on the ceilings and walls of villas, hotels, exhibit halls, and other establishments.
Brand-new 11ac Wireless Technology
The WDAP-C7200AC supports IEEE 802.11a/b/g/n/ac dual band standards with 2T2R MIMO technology; therefore, it provides the wireless speed up to 300+867Mbps, which is 16X faster than the 11a access point at
5GHz frequency and 5.5X faster than the 11g access point at 2.4GHz frequency. Moreover, the
WDAP-C7200AC is equipped with Gigabit Ethernet Port. Compared with the general wireless APs, the
WDAP-C7200AC offers faster transmission speed for the network applications and less interference to enhance data throughput. The incredible wireless speed makes it ideal for handling multiple HD movie streams, high-resolution on-line games, stereo music, VoIPs and data streams at the same time stably and smoothly.
-2-
User Manual of WDAP-C7200AC
11ac Innovations Bring Excellent Data Link Speed
The WDAP-C7200AC is built-in with high power amplifier and 4 highly-sensitive antennas which provide stronger signal and excellent coverage even in the wide-ranging or bad environment. With adjustable transmit power option, the administrator can flexibly reduce or increase the output power for various environments, thus reducing interference to achieve maximum performance. To provide extremely high-speed user experience, the
WDAP-C7200AC adopts IEEE 802.11ac technology to extend the 802.11n 40MHz channel binding to 80MHz and the implementation of 256-QAM modulation where higher transmitting/receiving rates go up to 867Mbps in
5GHz less interference frequency band. In addition, the WDAP-C7200AC is equipped with gigabit LAN port to eliminate the restriction of 100Mbps Fast Ethernet wired connection to let users fully enjoy the high speed provided by wireless. The IEEE 802.11ac also optimizes MU-MIMO (Multi-User MIMO) mechanism to serve multiple devices simultaneously.
Full Support of Wireless Security Encryption and Wireless Value-added Features
In aspect of security, besides 64/128-bit WEP encryption, the WDAP-C7200AC is integrated with WPA / WPA2,
WPA-PSK / WPA2-PSK and 802.1x Radius authority to secure and protect your wireless LAN. It provides the wireless MAC filtering and SSID broadcast control to consolidate the wireless network security and prevent unauthorized wireless connection. Being an access point, the WDAP-C7200AC supports the VLAN function to allow multiple SSIDs (10 sets of SSIDs) to access Internal VLAN topology. Moreover, its Wi-Fi Multimedia (WMM) mechanism provides enhanced QoS over wireless connection for better performance in multimedia transmission like on-line gaming and video streaming, which are classified as a top priority.
-3-
User Manual of WDAP-C7200AC
Multiple Operation Modes for Various Applications
The WDAP-C7200AC supports AP, Client, WDS Bridge, Repeater and Universal Repeater modes, through which it provides more flexibility for users when wireless network is established. Compared with general wireless access point, the WDAP-C7200AC offers more powerful and flexible capability for wireless clients.
Flexible Deployment with PoE Feature
Compliant with the IEEE 802.3at Power over Ethernet standard, the WDAP-C7200AC can be powered and networked by a single UTP cable. It thus reduces the needs of extra cables and dedicated electrical outlets on
-4-
User Manual of WDAP-C7200AC
the wall, ceiling or any other place where it is difficult to reach. The wireless network deployment becomes more flexible and worry-free from the power outlet locations.
Easy Installation and Management
With user-friendly Web UI and step-by-step Quick Setup Wizard, the WDAP-C7200AC is easy to install, even for users who never experience setting up a wireless network. Furthermore, with SNMP-based management interface, the WDAP-C7200AC is convenient to be managed and configured remotely in a small business wireless network.
-5-
User Manual of WDAP-C7200AC
1.3 Product Features
Standard Compliant Hardware Interface
Complies with IEEE 802.11ac (draft 2.0) and IEEE 802.11a/b/g/n standards
1 x 10/100/1000Base-TX Port with 1-port PoE (PD, Powered Device)
IEEE 802.3at Power over Ethernet design
RF Interface Characteristics
Features 2.4GHz (802.11b/g/n) and 5GHz (802.11a/n/ac) concurrent dual band for more efficiency of carrying high load traffic
2T2R MIMO technology for enhanced throughput and coverage
Provides multiple adjustable transmit power control
High speed up to 1.2Gbps (300Mbps for 2.4GHz + 867Mbps for 5GHz) wireless data rate
Comprehensive Wireless Advanced Features
Multiple Wireless Modes: AP, Client, WDS PtP/ PtMP, WDS Repeater, Universal Repeater
Supports up to 10 multiple-SSIDs (2.4GHz+5GHz) to allow users to access different networks through a single AP
Supports VLAN function to limit the clients to access the specific internal network resource
Supports WMM (Wi-Fi Multimedia) and wireless QoS to enhance the efficiency of multimedia application
Supports IAPP (Inter Access Point Protocol) and wireless roaming to enable clients to roam across different wireless networks
Supports 5-level Transmitting Power Control to adapt various environments
Supports wireless schedule to automatically enable or disable the wireless function based on predefined schedule
Secure Network Connection
Advanced security: 64/128-bit WEP, WPA / WPA2, WPA-PSK / WPA2-PSK (TKIP/AES encryption) and 802.1x Radius Authentication
Supports MAC address filtering
Easy Installation & Management
Flexible deployment with standard 802.3at PoE/ PD supported
Web-based UI and Quick Setup Wizard for easy configuration
Remote Management allows configuration from a remote site
SNMP-based management interface
System status monitoring includes DHCP Client and System Log
-6-
User Manual of WDAP-C7200AC
1.4 Product Specifications
Product
WDAP-C7200AC
1200Mbps 802.11ac Dual Band Ceiling Mount Wireless Access Point
Hardware Specifications
Interfaces
Antennas
LAN
Gain:
1 x 10/100/1000Base-T RJ45 port
Auto-negotiation and Auto MDI/MDI-X
2 x 2.4GHz 3dBi PCBA antenna
2 x 5GHz 2.5dBi PCBA antenna
Reset button on the top cover
Reset Button
Press over 7 seconds to reset the device to factory default
LED Indicators
PWR
Allow LED to turn off via software control
Plastic
Material
Dimensions (Φ x H)
Weight
194 x 49 mm
300 ±5g
Power Requirements
802.3at PoE, 48-56V DC input
Power Consumption
20W (max.)
Mounting
Ceiling Mount
Wireless Interface Specifications
Standard
IEEE 802.11ac (Draft 2.0) 5GHz
IEEE 802.11a/n 5GHz
IEEE 802.11b/g/n 2.4GHz
Antenna Structure
Modulation
Data Modulation
802.11ac: 2T2R MU-MIMO
802.11n: 2T2R MIMO
DSSS
802.11ac: OFDM (BPSK / QPSK / 16QAM / 64QAM / 256QAM)
802.11a/g/n: OFDM (BPSK / QPSK / 16QAM / 64QAM)
802.11b: DSSS (DBPSK / DQPSK / CCK)
Band Mode
2.4G / 5G concurrent mode
Frequency Range
2.4GHz
America/ FCC: 2.412~2.462GHz
Europe/ ETSI: 2.412~2.484GHz
5GHz
America/ FCC: 5.180~5.240GHz, 5.725~5.850GHz
Europe/ ETSI: 5.180~5.240GHz
Operating Channels
Channel Width
2.4GHz
America/ FCC: 1~11
Europe/ ETSI: 1~13
5GHz
America/ FCC:
36, 40, 44, 48, 149, 153, 157, 161, 165
Europe/ ETSI:
36, 40, 44, 48
5GHz channel list will vary in different countries according to their regulations.
802.11ac: 20/40/80MHz
802.11n: 20/40MHz
-7-
Data Transmission
Rates
Transmission Distance
Max. RF Power
Receive Sensitivity
User Manual of WDAP-C7200AC
802.11ac (VHT20, Nss2-MCS8): Up to 173.3Mbps
802.11ac (VHT40, Nss2-MCS9): Up to 400Mbps
802.11ac (VHT80, Nss2-MCS9): Up to 867Mbps
802.11n (HT40): 270/243/216/162/108/81/54/27Mbps
135/121.5/108/81/54/40.5/27/13.5Mbps (dynamic)
802.11n (HT20): 130/117/104/78/52/39/26/13Mbps
65/58.5/52/39/26/19.5/13/6.5Mbps (dynamic)
802.11g: 54/48/36/24/18/12/9/6Mbps (dynamic)
802.11b: 11/5.5/2/1Mbps (dynamic)
802.11ac (draft): up to 30m
802.11n: up to 70m
802.11g: up to 30m
The estimated transmission distance is based on the theory. The actual distance will vary in different environments.
5GHz:
802.11ac (VHT20): 22dBm
802.11ac (VHT40): 22dBm
802.11ac (VHT80): 22dBm
802.11n (HT20): 22dBm
802.11n (HT40): 22dBm
802.11a: 22dBm
2.4GHz:
802.11n: 17 ±2.5dBm
802.11b/g: 20 ±2.5dBm
5GHz:
802.11ac (VHT20): -91dBm @ Nss1-MCS0, -64dBm @ Nss2-MCS8
802.11ac (VHT40): -89dBm @ Nss1-MCS0, -59dBm @ Nss2-MCS9
802.11ac (VHT80): -86dBm @ Nss1-MCS0, -56dBm @ Nss2-MCS9
802.11n (HT20): -92dBm @ MCS0, -71dBm @ MCS7
802.11n (HT40): -89dBm @ MCS0, -66dBm @ MCS15
802.11a: -93 @ 6Mbps, -75dBm @ 54Mbps
2.4GHz:
802.11n 20MHz (MCS7): -69dBm @10% PER
802.11n 40MHz (MCS15): -66dBm @10% PER
802.11g (54Mbps): -74dBm @10% PER
802.11b (11Mbps): -88dBm @10% PER
Software Features
Wireless Mode
Encryption Security
Wireless Security
Universal Repeater
(AP+Client)
Repeater
(WDS+AP)
AP (Access Point)
WDS PTP (Point to Point)
WDS PTMP (Point to Multipoint)
Client
WEP (64/128-bit) encryption security
WPA / WPA2 (TKIP/AES)
WPA-PSK / WPA2-PSK (TKIP/AES)
Provides wireless LAN ACL (Access Control List) filtering
Wireless MAC address filtering
-8-
User Manual of WDAP-C7200AC
Supports WPS (Wi-Fi Protected Setup)
Enable/ Disable SSID Broadcast
WMM (Wi-Fi Multimedia): 802.11e Wireless QoS
Multiple SSID: up to 5 at 2.4GHz and 5GHz, respectively
Wireless Advanced
Max. Clients
Wireless Isolation: Enables to isolate each connected wireless client from communicating with each other
IAPP (Inter Access Point Protocol): 802.11f Wireless Roaming
Provides Wireless Statistics
Wire: 253
2.4GHz Wireless: 32
5GHz Wireless: 32
Built-in DHCP server supporting static IP address distributing
Supports UPnP
LAN
Supports 802.1d Spanning Tree
Supports 802.1Q VLAN
Web-based (HTTP) management interface
SNTP time synchronize
System Management
Easy firmware upgrade
Supports Scheduling Reboot
Supports Smart Discovery Utility
Standards Conformance
IEEE Standards
IEEE 802.11ac (Draft 2.0, 2T2R, up to 867Mbps)
IEEE 802.11n (2T2R, up to 300Mbps)
IEEE 802.11g
IEEE 802.11b
IEEE 802.11i
IEEE 802.3 10Base-T
IEEE 802.3u 100Base-TX
IEEE 802.3ab 1000Base-T
IEEE 802.3x Flow Control
Other Protocols and
CSMA/CA, CSMA/CD, TCP/IP, DHCP, ICMP, SNTP
Standards
Environment & Certification
Operating: 0 ~ 50 degrees C
Temperature
Storage: -40 ~ 70 degrees C
Humidity
Operating: 10 ~ 90% (non-condensing)
Storage: 5 ~ 90% (non-condensing)
Regulatory
FCC Part 15B & 15C, IC, RoHS
-9-
User Manual of WDAP-C7200AC
Chapter 2. Hardware Installation
Please follow the instructions below to connect WDAP-C7200AC to the existing network devices and your computers.
2.1 Product Outlook
Dimensions: 194 x 49 mm
(
Φ x H)
Drawing :
Figure 2-1 WDAP-C7200AC Product Drawing
-10-
User Manual of WDAP-C7200AC
2.1.1 Panel Layout
The front and rear panel provide a simple interface monitoring the AP. Figure 2-2 shows the hardware interface of the WDAP-C7200AC.
Hardware Interface
Figure 2-2 WDAP-C7200AC Panel Layout
2.1.2 Hardware Description
LED definition
LED
PWR
COLOR STATUS
Green
Green
Orange
On Device
Off
On
FUNCTION
on
Device power off (control by S/W)
System initializing, turned it off when system completed
Orange
Blinking
Detect and identify the LED (control by S/W)
1) Position LED on: LED blinks continuously.
2) Position LED off: the LED is off.
Button definition
Object
Reset
Description
To restore to the factory default setting, press and hold the Reset Button over 7 seconds, and then release it.
Port definition
Object
PoE Port
(802.3at PoE)
Description
10/100/1000Mbps RJ-45 port , Auto MDI/ MDI-X
Connect PoE port to the IEEE 802.3at PSE to power on the device.
-11-
User Manual of WDAP-C7200AC
Chapter 3. Connecting to the AP
3.1 System Requirements
Broadband Internet Access Service (Cable/xDSL/Ethernet connection)
One IEEE 802.3at PoE switch (supply power to the WDAP-C7200AC)
PCs with a working Ethernet Adapter and an Ethernet cable with RJ-45 connectors
PCs running Windows 98/ME, NT4.0, 2000/XP, Windows Vista / Win 7, MAC OS 9 or later, Linux,
UNIX or other platforms compatible with TCP/IP protocols
1. The AP in the following instructions refers to PLANET WDAP-C7200AC.
2. It is recommended to use Internet Explore 7.0 or above to access the AP.
3.2 Installing the AP
Before installing the AP, make sure your PoE switch is connected to the Internet through the broadband service successfully at this moment. If there is any problem, please contact your local ISP. After that, please install the
AP according to the following steps. Don't forget to pull out the power plug and keep your hands dry.
Step 1. Drill the outlet hole indicated on the mounting label and stick the given mounting label to the installation location to let the Ethernet cable penetrate the outlet hole. Then, drill the mounting holes as indicated on the label.
Figure 3-1 WDAP-C7200AC Installation Diagram 1
Step 2. Take the mounting bracket, put it on the target place by aligning the holes and fix it with the supplied
-12-
screws.
※
IEEE 802.3at PoE switch is required.
User Manual of WDAP-C7200AC
Figure 3-2 WDAP-C7200AC Installation Diagram 2
Step 3. Plug the RJ-45 Ethernet cable into the PoE port of the WDAP-C7200AC.
Figure 3-3 WDAP-C7200AC Installation Diagram 3
Step 4. Load the device into the mounting bracket, and be sure the device is mated with two fixed screws.
Then, rotate the device clockwise to lock it in position.
-13-
User Manual of WDAP-C7200AC
Figure 3-4 WDAP-C7200AC Installation Diagram 4
Step 5. Plug the other end of the Ethernet cable into the PoE switch.
Figure 3-5 WDAP-C7200AC Installation Diagram 4
-14-
User Manual of WDAP-C7200AC
Chapter 4. Quick Installation Guide
This chapter will show you how to configure the basic functions of your AP within minutes.
A computer with wired Ethernet connection to the Wireless AP is required for the first-time configuration.
4.1 Manual Network Setup - TCP/IP Configuration
The default IP address of the WDAP-C7200AC is
192.168.1.253
. And the default Subnet Mask is 255.255.255.0.
These values can be changed as you want. In this guide, we use all the default values for description.
Connect the WDAP-C7200AC with your PC by an Ethernet cable plugging in LAN port on one side and in LAN port of PC on the other side. Please power on the WDAP-C7200AC by PoE switch through the PoE port.
In the following sections, we’ll introduce how to install and configure the TCP/IP correctly in Windows 7. And the procedures in other operating systems are similar. First, make sure your Ethernet Adapter is working, and refer to the Ethernet adapter manual if needed.
4.1.1 Configuring the IP Address Manually
Summary:
Set up the TCP/IP Protocol for your PC.
Configure the network parameters. The IP address is 192.168.1.xxx (if the default IP address of the
WDAP-C7200AC is 192.168.1.253, and the DSL router is 192.168.1.254, the "xxx" can be configured to any number from 1 to 252), Subnet Mask is 255.255.255.0.
1
Select Use the following IP address radio button, and then configure the IP address of the PC.
2
For example, as the default IP address of the WDAP-C7200AC is 192.168.1.253 and the DSL router is
192.168.1.254, you may choose from 192.168.1.1 to 192.168.1.252.
-15-
User Manual of WDAP-C7200AC
Figure 4-1 TCP/IP Setting
Now click OK to save your settings.
Now, you can run the Ping command in the command prompt to verify the network connection between your
PC and the AP. The following example is in Windows 7 OS. Please follow the steps below:
-16-
User Manual of WDAP-C7200AC
Figure 4-2 Windows Start Menu
3. Open a command prompt, type ping 192.168.1.253 and then press Enter.
If the result displayed is similar to
Figure 4-3
, it means the connection between your PC and the AP has been established well.
Figure 4-3 Successful result of Ping command
If the result displayed is similar to
Figure 4-4
, it means the connection between your PC and the AP has failed.
-17-
User Manual of WDAP-C7200AC
Figure 4-4 Failed Result of Ping Command
If the address is 0.0.0.0, check your adapter installation, security settings, and the settings on your AP. Some firewall software programs may block a DHCP request on newly installed adapters.
-18-
User Manual of WDAP-C7200AC
4.2 Starting Setup in the Web UI
It is easy to configure and manage the AP with the web browser.
Step 1. To access the configuration utility, open a web-browser and enter the default IP address http://192.168.1.253
in the web address field of the browser.
Figure 4-5 Login by default IP address
After a moment, a login window will appear. Enter admin for the User Name and Password, both in lower case letters. Then click the OK button or press the Enter key.
Figure 4-6 Login Window
Default IP Address: 192.168.1.253
Default User name: admin
Default Password: admin
If the above screen does not pop up, it may mean that your web-browser has been set to a proxy. Go to Tools menu>Internet Options>Connections>LAN Settings on the screen that appears, cancel the Using Proxy checkbox, and click OK to finish it.
-19-
User Manual of WDAP-C7200AC
Chapter 5. Configuring the AP
This chapter delivers a detailed presentation of AP’s functionalities and features under 6 main menus below, allowing you to manage the AP with ease.
Figure 5-1 Main Menu
During operation, if you are not clear about a certain feature, you can refer to the “ Help” section in the right side of the screen to read all related helpful info.
5.1 Setup Wizard
The Setup Wizard will guide the user to configure the WDAP-C7200AC easily and quickly. Select the Setup
Wizard on the left side of the screen and by clicking on Next on the Setup Wizard screen shown below, you will then name your WDAP-C7200AC and set up its security.
Figure 5-2 Setup Wizard
-20-
Step 1: LAN Interface Setup
User Manual of WDAP-C7200AC
Figure 5-3 LAN Interface SetupTopology
Figure 5-4 Wizard – LAN Interface Setup
The page includes the following fields:
Object
IP Address
Subnet Mask
Default Gateway
Description
Displays the current IP address of the AP. (Default = 192.168.1.253)
Displays LAN mask of the AP. (Default = 255.255.255.0)
IP address of the associated router. (Default = 192.168.1.254)
Step 2: Time Zone Setting
Figure 5-5 Time Zone Setup Topology
-21-
User Manual of WDAP-C7200AC
Figure 5-6 Wizard – Time Zone Setup
The page includes the following fields:
Object
Enable NTP client update
Automatically adjust
Daylight Saving
Time Zone Select
NTP Server
Enable NTP client update
Description
Check this box to connect NTP Server and synchronize internet time.
Check this box and system will adjust the daylight saving automatically.
Select the Time Zone from the drop-down menu.
Select the NTP Server from the drop-down menu.
Check this box to connect NTP Server and synchronize internet time.
Step 3: Wireless 5GHz Basic Settings
Figure 5-7 Wizard – Wireless 5GHz Basic Settings
The page includes the following fields:
-22-
User Manual of WDAP-C7200AC
Object
Band
Mode
SSID
Channel Width
Control Sideband
Channel Number
Description
Supports 802.11a, 802.11n, 802.11ac and mixed. Please choose its band according to your clients.
Supports AP, Client, WDS and AP+WDS mode.
Service Set Identifier identifies your wireless network.
Select 80MHz if you use 802.11ac; select 40MHz if you use 802.11n; otherwise, 20MHz for the 802.11a mode.
It is only valid when you choose channel width 40MHz.
Indicates the channel setting for the AP.
Step 4: Wireless 5GHz Security Settings
Secure your wireless network by turning on the WPA or WEP security feature on the router. For this section you can set WEP and WPA-PSK security mode.
Figure 5-8 Wizard – Wireless 5GHz Security Setup
Encryption: WEP
The following picture shows how to set the WEP security.
Figure 5-9 5GHz Wireless Security Setup – WEP Setting
The page includes the following fields:
Object
Key length
Key Format
Key Setting
Description
WEP supports 64-bit or 128-bit security key.
User can enter key in ASCII or Hex format.
Enter the key whose format is limited by the Key format, ASCII or Hex.
-23-
User Manual of WDAP-C7200AC
Encryption: WPA-PSK
The following picture shows how to set up WPA-PSK security. You can select
WPA (TKIP)
,
WPA2 (AES)
and
Mixed mode
.
Figure 5-10 5GHz Wireless Security Setup – WPA Setting
The page includes the following fields:
Object
Pre-Shared Key Format
Pre-Shared Key
Description
Specify the format of the key, pass phrase or hex.
Enter the key whose format is limited by the key format.
Step 5: Wireless 2.4GHz Basic Settings
Figure 5-11 Wizard – Wireless 2.4GHz Basic Settings
The page includes the following fields:
-24-
Object
Band
Mode
SSID
Channel Width
Control Sideband
Channel Number
User Manual of WDAP-C7200AC
Description
Supports 802.11b, 802.11g, 802.11n and mixed. Please choose its band according to your clients.
Supports AP, Client, WDS and AP+WDS mode.
Service Set Identifier, it identifies your wireless network.
Select 40MHz if you use 802.11n, otherwise 20MHz for the 802.11b/g mode.
It is only valid when you choose channel width 40MHz.
Indicates the channel setting for the AP.
Step 6: Wireless 2.4GHz Security Settings
Secure your wireless network by turning on the WPA or WEP security feature on the router. For this section you can set WEP and WPA-PSK security mode.
Figure 5-12 Wizard – Wireless 2.4GHz Security Setup
Encryption: WEP
The following picture shows how to set the WEP security.
Figure 5-13 2.4GHz Wireless Security Setup – WEP Setting
The page includes the following fields:
-25-
Object
Key Length
Key Format
Key Setting
User Manual of WDAP-C7200AC
Description
WEP supports 64-bit or 128-bit security key.
User can enter key in ASCII or Hex format.
Enter the key whose format is limited by the Key format, ASCII or Hex.
Encryption: WPA-PSK
The following picture shows how to set WPA-PSK security. You can select
WPA (TKIP)
,
WPA2 (AES)
and
Mixed mode
.
Figure 5-14 2.4GHz Wireless Security Setup – WPA Setting
The page includes the following fields:
Object
Pre-Shared Key Format
Pre-Shared Key
Description
Specify the format of the key, pass phrase or hex.
Enter the key whose format is limited by the key format.
Click the Finished button to make your wireless configuration to take effect and finish the Setup Wizard.
Figure 5-15 Setup Wizard - Finished
After rebooting, please check whether you can access the Internet or not on the “Status” page.
-26-
User Manual of WDAP-C7200AC
5.2 TCP / IP Settings
This page is used to configure the parameters for local area network which connects to the LAN port of your AP.
Here you may change the setting for IP address, subnet mask, DHCP, etc.
5.2.1 LAN Settings
On the LAN Settings page, you can configure the IP parameters of the LAN on the screen as shown below.
Figure 5-16 LAN Setting
The page includes the following fields:
Object
IP Address
Description
The default LAN IP address of the WDAP-C7200AC is 192.168.1.253.
You can change it according to your request.
-27-
Subnet Mask
User Manual of WDAP-C7200AC
Default is 255.255.255.0. You can change it according to your request.
Default Gateway
Default is 192.168.1.253. You can change it according to your request.
DHCP
DHCP Client Range
Static DHCP
Domain Name
You can select a Disabled, Client, and Server. Default is Disabled, meaning the WDAP-C7200AC must connect to a router to assign IP addresses to clients.
For the Server mode, you must enter the DHCP client IP address range in the field. And you can click the “Show Client” button to show the Active DHCP Client Table.
Click the “Set Static DHCP” button and you can reserve some IP addresses for those network devices with the specified MAC addresses anytime when they request IP addresses.
Default is Planet.
802.1d Spanning Tree
You can enable or disable the Spanning Tree function.
Clone MAC Address
You can input an MAC address here for using clone function.
UPnP Enable
You can enable or disable the UPnP function.
The UPnP feature allows the devices, such as Internet computers, to access the local host resources or devices as needed. UPnP devices can be automatically discovered by the UPnP service application on the LAN.
If you change the IP address of LAN, you must use the new IP address to login the
AP.
When the IP address of the WDAP-C7200AC is changed, the clients on the network often need to wait for a while or even reboot before they can access the new IP address. For an immediate access to the AP, please flush the netbios cache on the client computer by running the “nbtstat –r” command before using the device name of the WDAP-C7200AC to access its Web Management page.
-28-
User Manual of WDAP-C7200AC
5.3 WLAN1 (5GHz)
The wireless menu of WLAN1 (5GHz) contains submenus of the settings about wireless network. Please refer to the following sections for the details.
Figure 5-17 5GHz Wireless Main Menu
5.3.1 Basic Settings
Choose menu “WLAN1 (5GHz) Basic Settings” and you can configure the 5GHz basic settings for the wireless network on this page. After the configuration is done, please click the “Apply Changes” button to save the settings.
First of all, the wireless AP supports multiple wireless modes for different network applications, which include:
AP
Multiple SSIDs
Universal Repeater
Client
WDS
AP+WDS
It is so easy to combine the WDAP-C7200AC with the existing wired network. The WDAP-C7200AC definitely provides a total network solution for the home and the SOHO users.
AP
Standard Access Point
-29-
Internet
AP Mode
User Manual of WDAP-C7200AC
AP(Multi-SSID) Mode
WDAP-C7200AC
SSID-1(5G)
Clients
SSID-2(2.4G)
Clients
Figure 5-18 5GHz Wireless Basic Settings of AP
The page includes the following fields:
-30-
User Manual of WDAP-C7200AC
Object Description
Disable Wireless LAN
Interface
Check the box to disable the wireless function.
Band
Mode
Select the desired mode. Default is “5GHz (A+N+AC)”. It is strongly recommended that you set the Band to “5GHz (A+N+AC)”, and all of
802.11a, 802.11n, and 802.11ac wireless stations can connect to the
WDAP-C7200AC.
5 GHz (A): 802.11a mode, rate is up to 54Mbps
5 GHz (N): 802.11n mode, rate is up to 300Mbps
5 GHz (AC): 802.11n mode, rate is up to 867Mbps(2T2R)
5 GHz (A+N): 802.11a/n mode, rate is up to 300Mbps
5 GHz (N+AC): 802.11n/ac mode, rate is up to 300Mbps or
867Mbps
5 GHz (A+N+AC): 802.11a/n/ac mode, rate is up to 54Mbps,
300Mbps, or 867Mbps
There are four kinds of wireless mode selections:
AP
Client
WDS
AP+WDS
If you select WDS or AP+WDS, please click “WDS Settings” submenu for the related configuration. Furthermore, click the “Multiple AP” button to enable multiple SSID functions.
SSID
Channel Width
Channel Number
The ID of the wireless network. User can access the wireless network through it only. However, if you switch to Client Mode, this field becomes the SSID of the AP you want to connect with.
Default: Planet AP 5G
You can select 20MHz, 40MHz or 80MHz.
You can select the operating frequency of wireless network.
Default: 149
Broadcast SSID
Data Rate
If you enable “Broadcast SSID”, every wireless station located within the coverage of the AP can discover its signal easily. If you are building a public wireless network, enabling this feature is recommended. In private network, disabling “Broadcast SSID” can provide better wireless network security.
Default is “Enabled”.
Set the wireless data transfer rate to a certain value. Since most of wireless devices will negotiate with each other and pick a proper data transfer rate automatically, it’s not necessary to change this value
-31-
User Manual of WDAP-C7200AC
AP(Multi-SSID) Mode
Default is “
Auto”.
Associated Clients
Enable Universal
Repeater Mode
(Acting as AP and client simultaneously)
Click the “
Show Active Clients” button to show the status table of active wireless clients.
Universal Repeater is a technology used to extend wireless coverage.
To enable Universal Repeater Mode, check the box and enter the
SSID you want to broadcast in the field below. Then please click
“Security” submenu for the related settings of the AP you want to connect with.
Multiple-SSID
Enable multiple-SSID can broadcast multiple WLAN SSID's using virtual interfaces. You can have different encryption settings for each WLAN and you can restrict what they have access to.
Internet
AP Mode
AP(Multi-SSID) Mode
WDAP-C7200AC
SSID-1(5G)
Clients
SSID-2(2.4G)
Clients
Choose menu “
WLAN1 (5GHz) → Basic Settings → Multiple AP” to configure the device as a general wireless access point with multiple SSIDs.
Figure 5-19 5GHz Wireless Basic Settings – Multiple AP
-32-
User Manual of WDAP-C7200AC
The device supports up to four multiple Service Set Identifiers. You can back to the Basic Settings page to set the Primary SSID. The SSID’s factory default setting is Planet 5G VAP1~4 (Multiple-SSID 1~4). The
SSID can be easily changed to connect to an existing wireless network or to establish a new wireless network. When the information for the new SSID is finished, click the Apply Changes button to let your changes take effect.
Figure 5-20 5GHz Multiple-SSID
Once you have applied and saved those settings, you can then go to the “ WLAN1 (5GHz) → Security” page on the AP to set up security settings for each of the SSIDs.
Universal Repeater
This mode allows the AP with its own BSS to relay data to a root AP to which it is associated with WDS disabled. The wireless repeater relays signal between its stations and the root AP for greater wireless range.
Universal Repeater Mode
WDAP-C7200AC
Internet
a/n/ac
5G
a/n/ac g/n
Switch
Clients
2.4G
AP
g/n
Smart Phone
1. Example of how to configure Universal Repeater Mode. Please take the following steps:
To configure each wireless parameter, please go to the “ WLAN1 (5GHz) → Basic Settings” page.
Step 1. Configure wireless mode to “AP” and then check “Enable Universal Repeater Mode (Acting as AP
-33-
User Manual of WDAP-C7200AC
and client simultaneously)”. Click “Apply Changes” to take effect.
Figure 5-21 5GHz Universal Repeater-1
Step 2. Go to 5GHz Site Survey page to find the root AP. Select the root AP that you want to repeat the signal and then click “Next”.
-34-
User Manual of WDAP-C7200AC
Figure 5-22 5GHz Universal Repeater-2
Step 3. Select the correct encryption method and enter the security key. Then, click “Connect”.
Figure 5-23 5GHz Universal Repeater-3
Step 4. Check “Add to Wireless Profile” and click “Reboot Now”.
Figure 5-24 5GHz Universal Repeater-4
Step 5. Go to “Management-> Status” page to check whether the state of Repeater interface should be
“Connected”.
-35-
User Manual of WDAP-C7200AC
Figure 5-25 5GHz Universal Repeater-5
Client (Infrastructure)
Combine the Wireless Router to the Ethernet devices such as TV, game player, or HDD and DVD, to make them be wireless stations.
Station (Client Mode)
Internet
AP
a/n/ac
5G
WDAP-C7200AC
a/n/ac
Switch
Clients
-36-
User Manual of WDAP-C7200AC
Figure 5-26 5GHz Wireless Basic Settings – Client
The page includes the following fields:
Object Description
Disable Wireless LAN
Interface
Check the box to disable the wireless function.
Band
Select the desired mode. Default is “5GHz (A+N+AC)”. It is strongly recommended that you set the Band to “5GHz (A+N+AC)”, and all of
802.11a, 802.11n, and 802.11ac wireless stations can connect to the
WDAP-C7200AC.
5 GHz (A): 802.11a mode, rate is up to 54Mbps
5 GHz (N): 802.11n mode, rate is up to 300Mbps
5 GHz (AC): 802.11n mode, rate is up to 867Mbps(2T2R)
-37-
Mode
Network Type
SSID
Broadcast SSID
Data Rate
User Manual of WDAP-C7200AC
5 GHz (A+N): 802.11a/n mode, rate is up to 300Mbps
5 GHz (N+AC): 802.11n/ac mode, rate is up to 300Mbps or
867Mbps
5 GHz (A+N+AC): 802.11a/n/ac mode, rate is up to 54Mbps,
300Mbps, or 867Mbps
There are four kinds of wireless mode selections:
AP
Client
WDS
AP+WDS
If you select WDS or AP+WDS, please click “WDS Settings” submenu for the related configuration. Furthermore, click the “Multiple AP” button to enable multiple SSID function.
In Infrastructure, the wireless LAN serves as a wireless station. And the user can use the PC equipped with the WDAP-C7200AC to access the wireless network via other access points. In Ad hoc, the wireless
LAN will use the Ad-hoc mode to operate.
Default is “Infrastructure”.
Note: Only while the wireless mode is set to “Client”, then the
Network Type can be configured.
The ID of the wireless network. User can access the wireless network via its ID. However, if you switch to Client mode, this field becomes the
SSID of the AP you want to connect with.
Default: Planet AP 5G
If you enable “Broadcast SSID”, every wireless station located within the coverage of the WDAP-C7200AC can discover its signal easily. If you are building a public wireless network, enabling this feature is recommended. In private network, disabling “Broadcast SSID” can provide better wireless network security.
Default is “Enabled”.
Set the wireless data transfer rate to a certain value. Since most of wireless devices will negotiate with each other and pick a proper data transfer rate automatically, it’s not necessary to change this value
unless you know what will happen after modification.
Default is “Auto”.
Enable Mac Clone
(Single Ethernet Client)
Enable Mac Clone.
Example of how to configure Client Mode. Please take the following steps:
-38-
User Manual of WDAP-C7200AC
To configure each wireless parameter, please go to the “WLAN1 (5GHz) → Basic Settings” page.
Step 1. Go to “WLAN1 (5GHz) → Site Survey” page and click “Site Survey” button.
Figure 5-27 Client – Survey
Step 2. Choose the root AP from the list. If the root AP is not listed in the table, re-click “Site Survey” to update the list.
-39-
User Manual of WDAP-C7200AC
Figure 5-28 Client – AP List
Step 3. Enter the Security Key of the root AP and then click “Connect”.
Figure 5-29 Client – Security
-40-
User Manual of WDAP-C7200AC
Step 4. Wait until the connection established. Check the “Add to Wireless Profile” option and then reboot it.
Figure 5-30 Client – Status
WDS
Connect this Wireless AP with up to 8 WDS-capable wireless APs to expand the scope of network.
WDS Bridge-PtP Mode
WDAP-C7200AC WDAP-C7200AC
Clients Switch Switch Clients
WDS Bridge-PtMP Mode
WDAP-C7200AC
AP
Switch Clients
Clients Switch
AP
Switch Clients
-41-
User Manual of WDAP-C7200AC
Figure 5-31 5GHz Wireless Basic Settings – WDS
The page includes the following fields:
Object Description
Disable Wireless LAN
Interface
Check the box to disable the wireless function.
Band
Select the desired mode. Default is “5GHz (A+N+AC)”. It is strongly recommended that you set the Band to “5GHz (A+N+AC)”, and all of
802.11a, 802.11n, and 802.11ac wireless stations can connect to the
-42-
Mode
Channel Width
Control Sideband
Channel Number
Data Rate
User Manual of WDAP-C7200AC
WDAP-C7200AC.
5 GHz (A): 802.11a mode, rate is up to 54Mbps
5 GHz (N): 802.11n mode, rate is up to 300Mbps
5 GHz (AC): 802.11n mode, rate is up to 867Mbps(2T2R)
5 GHz (A+N): 802.11a/n mode, rate is up to 300Mbps
5 GHz (N+AC): 802.11n/ac mode, rate is up to 300Mbps or
867Mbps
5 GHz (A+N+AC): 802.11a/n/ac mode, rate is up to 54Mbps,
300Mbps, or 867Mbps
There are four kinds of wireless mode selections:
AP
Client
WDS
AP+WDS
If you select WDS or AP+WDS, please click “WDS Settings” submenu for the related configuration. Furthermore, click the “Multiple AP” button to enable multiple SSID function.
You can select 20MHz, 40MHz or 80MHz.
You can select Upper or Lower.
You can select the operating frequency of wireless network.
Set the wireless data transfer rate to a certain value. Since most of wireless devices will negotiate with each other and pick a proper data transfer rate automatically, it’s not necessary to change this value
unless you know what will happen after modification.
Default is “Auto”.
-43-
User Manual of WDAP-C7200AC
AP+ WDS
Connect this wireless AP with up to 8 WDS-capable wireless APs, and connect another AP to provide service for all wireless stations within its coverage.
WDS Repeater Mode
Internet
AP a/n/ac
5G WDS
WDAP-C7200AC
2.4G
g/n
Clients a/n/ac g/n
Switch
Figure 5-32 5GHz Wireless Basic Settings – WDS+AP
-44-
User Manual of WDAP-C7200AC
The page includes the following fields:
Object Description
Disable Wireless LAN
Interface
Check the box to disable the wireless function.
Country
Band
Mode
SSID
Select your region from the pull-down list.
This field specifies the region where the wireless function of the Router can be used. It may be illegal to use the wireless function of the Router in a region other than one of those specified in this field. If your country or region is not listed, please contact your local government agency for assistance.
Select the desired mode. Default is “5GHz (A+N+AC)”. It is strongly recommended that you set the band to “5GHz (A+N+AC)”, and all of
802.11a, 802.11n, and 802.11ac wireless stations can connect to the
WDAP-C7200AC.
5 GHz (A): 802.11a mode, rate is up to 54Mbps
5 GHz (N): 802.11n mode, rate is up to 300Mbps
5 GHz (AC): 802.11n mode, rate is up to 867Mbps(2T2R)
5 GHz (A+N): 802.11a/n mode, rate is up to 300Mbps
5 GHz (N+AC): 802.11n/ac mode, rate is up to 300Mbps or
867Mbps
5 GHz (A+N+AC): 802.11a/n/ac mode, rate is up to 54Mbps,
300Mbps, or 867Mbps
There are four kinds of wireless mode selections:
AP
Client
WDS
AP+WDS
If you select WDS or AP+WDS, please click “WDS Settings” submenu for the related configuration. Furthermore, click the “Multiple AP” button to enable multiple SSID functions.
The ID of the wireless network. User can access the wireless network via its ID only. However, if you switch to Client Mode, this field becomes the SSID of the AP you want to connect with.
Default: Planet AP 5G
Channel Width
Control Sideband
Channel Number
Broadcast SSID
You can select 20MHz, 40MHz or 80MHz.
You can select Upper or Lower.
You can select the operating frequency of wireless network.
If you enable “Broadcast SSID”, every wireless station located within the coverage of the WDAP-C7200AC can discover its signal easily. If you are building a public wireless network, enabling this feature is
-45-
Data Rate
User Manual of WDAP-C7200AC
recommended. In private network, disabling “Broadcast SSID” can provide better wireless network security.
Default is “Enabled”.
Set the wireless data transfer rate to a certain value. Since most of wireless devices will negotiate with each other and pick a proper data transfer rate automatically, it’s not necessary to change this value
unless you know what will happen after modification.
Default is “Auto”.
Associated Clients
Enable Universal
Repeater Mode
(Acting as AP and client simultaneously)
Click the “Show Active Clients” button to show the status table of active wireless clients.
Universal Repeater is a technology used to extend wireless coverage.
To enable Universal Repeater mode, check the box and enter the
SSID you want to broadcast in the field below. Then please click
“Security” submenu for the related settings of the AP you want to connect with.
5.3.2 Advanced Settings
Choose menu “WLAN1 (5GHz) Advanced Settings” and you can configure the 5GHz advanced settings for the wireless network on this page. After the configuration, please click the “Apply” button to save the settings.
Figure 5-33 Wireless Advanced Settings – 5GHz
-46-
User Manual of WDAP-C7200AC
The page includes the following fields:
Object
Fragment Threshold
RTS Threshold
Beacon Interval
IAPP
Protection
Aggregation
Short GI
WLAN Partition
STBC
LDPC
Description
You can specify the maximum size of packet during the fragmentation of data to be transmitted. If you set this value too low, it will result in bad performance.
Default is “2346”.
When the packet size is smaller than the RTS threshold, the access point will not use the RTS/CTS mechanism to send this packet.
Default is “2347”.
The interval of time that this access point broadcasts a beacon.
Beacon is used to synchronize the wireless network. Default is “100”.
IAPP (Inter-Access Point Protocol) enabled is recommended as it describes an optional extension to IEEE 802.11 that provides wireless access-point communications among multivendor systems.
Default is “Enabled”.
It is recommended to enable the protection mechanism. This mechanism can decrease the rate of data collision between 802.11b and 802.11g wireless stations. When the protection mode is enabled, the throughput of the AP will be a little lower due to the transmission of heavy frame traffic.
Default is “Disabled”.
It is a function where the values of multiple rows are grouped together.
Default is “Enabled”
It is used to set the time that the receiver waits for RF reflections to settle out before sampling data.
Default is “Enabled”
This feature is also called “WLAN isolation” or “Block Relay”. If this is enabled, wireless clients cannot exchange data through the
WDAP-C7200AC.
Default is “Disabled”.
Activate Space Time Blocking Code (STBC) which does not need channel statement information (CSI).
Default Setting: "Enabled"
Low-density Parity-check Code is wireless data transmit algorithm.
Default Setting: "Enabled"
5.3.3 RF Output Power
Choose menu “WLAN1 (5GHz) RF Output Power” to adjust to different levels of transmitting power for the wireless network according to various environments on this page. After the configuration, please click the “Apply
Changes” button to save the settings.
-47-
User Manual of WDAP-C7200AC
Figure 5-34 RF Output Power – 5GHz
RF Output Power Control provides the flexibility to control the Wi-Fi transmit power to optimize the wireless range. Wi-Fi power consumption for an Access Point could be reduced to up to 75% from its peak power consumption for serving small to medium size homes, while boosted to maximum power for large homes and businesses. The WDAP-C7200AC supports output power control levels up to 5. You can change the RF output power level here in accordance with various environments and signal strength.
5.3.4 Security
Choose menu “WLAN1 (5GHz) Security” and you can configure the settings of wireless security for the wireless network on this page. After the configuration, please click the “Apply Changes” button to save the settings.
-48-
User Manual of WDAP-C7200AC
Figure 5-35 Wireless Security Settings – 5GHz
The page includes the following fields:
Object
Select SSID
Encryption
Description
Select the SSID you want to configure the wireless security function, which includes the root one and the client one.
Disable:
No security setup for wireless connection.
WEP:
It is based on the IEEE 802.11 standard. And the default setting of authentication is Automatic, which can select Open System or Shared Key authentication type automatically based on the wireless station's capability and request. Furthermore, you can select Key Length and enter 10 and 26
Hexadecimal digits (any combination of 0-9, a-f, A-F, zero key is not promoted) or 5 and 13 ASCII characters in the Encryption Key field.
WPA:
WPA is a medium level encryption and is supported by most wireless devices and operating systems.
WPA2:
WPA2 is a high level encryption and is supported by most wireless devices and operating systems.
-49-
Authentication Mode
User Manual of WDAP-C7200AC
WPA / WPA2 / WPA-Mixed:
WPA Mixed Mode allows the use of both WPA and WPA2 at the same time.
Enterprise (RADIUS)
When you select the authentication mode based on Enterprise (Radius
Server), please enter the IP Address, Port, and Password of the Radius
Server.
Personal (Pre-Shared Key)
When you select the other authentication mode based on Personal
(Pre-Shared Key), please enter at least 8 ASCII characters (Passphrase) or
64 Hexadecimal characters. All of the Cipher Suites support TKIP and AES.
802.1x Authentication Enable 802.1x authentication function and then please enter the IP Address,
Port, and Password of the Radius Server.
5.3.5 Access Control
Choose menu “WLAN1 (5GHz) Access Control” to allow or deny the computer of specified MAC address to connect with the WDAP-C7200AC on this page. After the configuration, please click the “Apply Changes” button to save the settings.
Figure 5-36 Wireless Access Control – 5GHz
The page includes the following fields:
Object
Wireless Access
Control Mode
MAC Address
Description
You can choose to set the Allowed-List, Denied-List, or disable this function.
Enter the MAC address you want to allow or deny connection to the
WDAP-C7200AC in the field.
-50-
Comment
User Manual of WDAP-C7200AC
You can make some comment on each MAC address on the list.
Current Access Control
List
You can select some MAC addresses and click the “Delete Selected” button to delete it.
To deny a PC at the MAC address of 00:30:4F:00:00:01 (for example) to connect to your wireless network, do as follows:
Step 1. Select “Deny” from MAC Address Filter drop-down menu.
Step 2. Enter 00:30:4F:00:00:01 in the MAC address box and click “Add”.
Step 3. Click the “OK” button to save your settings and you can add more MAC addresses, if you like, simply repeat the above steps.
Figure 5-37 Wireless Access Control – Deny
-51-
User Manual of WDAP-C7200AC
5.3.6 WDS
WDS (Wireless Distribution System) feature can be used to extend your existing 2.4G or 5G wireless network coverage. Here we present you how to configure such feature in 2.4GHz, which also applies to 5GHz.
WDS Repeater Mode
Internet
AP a/n/ac
5G WDS
WDAP-C7200AC
2.4G
g/n
Clients a/n/ac g/n
Switch
WDS Bridge-PtMP Mode
WDAP-C7200AC
AP
Switch Clients
Clients Switch
AP
Switch Clients
WDS Repeater Mode
Internet
AP a/n/ac
5G WDS
WDAP-C7200AC
2.4G
g/n
Clients a/n/ac g/n
Switch
Before configuring the WDS Setting page, you have to select the wireless mode to “WDS” on the
WLAN1 (5GHz)
->
Basic Settings web page.
-52-
User Manual of WDAP-C7200AC
Figure 5-38 WDS Mode – 5GHz
Choose menu “WLAN1 (5GHz) WDS Settings” to configure WDS to connect the WDAP-C7200AC with another AP on this page. After the configuration, please click the “Apply Changes” button to save the settings.
Figure 5-39 WDS Settings – 5GHz
-53-
User Manual of WDAP-C7200AC
The page includes the following fields:
Figure 5-40 WDS – Set Security
Object
Enable WDS
MAC Address
Data Rate
Description
Check the box to enable the WDS function. Please select WDS or
AP+WDS in the Mode of Wireless Basic Settings before you enable
WDS on this page.
You can enter the MAC address of the AP you want to connect with.
Default is “Auto”.
Comment
Set Security
You can make some comment for each MAC address on the list.
Click the “Set Security” button to configure the wireless security parameters of the AP you want to connect via WDS.
Click the “Show Statics” button to show the WDS AP.
Show Statics
Current WDS AP List
You can select some MAC addresses of the AP and click the “Delete
Selected” button to delete it.
WDS feature can only be implemented between 2 wireless devices that both support the WDS feature. Plus, channel, security settings and security key must be the same on both such devices.
To encrypt your wireless network, click “Set Security”. For the detail of wireless security, see
. Do remember to reboot the device after you save your wireless security settings; otherwise, the WDS feature may not function.
-54-
User Manual of WDAP-C7200AC
5.3.7 Site Survey
Choose menu “WLAN1 (5GHz) Site Survey” to scan the available local AP. If any Access Point is found, you could choose any one to connect with manually when the Client Mode is enabled.
Figure 5-41 Site Survey – 5GHz
5.3.8 WPS
WPS (Wi-Fi Protected Setup) is designed to ease setup of security Wi-Fi networks and subsequently network management. This Wireless Router supports WPS features for AP mode, AP+WDS mode,
Infrastructure-Client mode, and the wireless root interface of Universal Repeater mode.
Simply enter a PIN code or press the software PBC button or hardware WPS button (if any) and a secure wireless connection is established.
PBC: If you find the WPS LED blinking for 2 minutes after you press the hardware WPS button on the device, it means that PBC encryption method is successfully enabled. And an authentication will be performed between your router and the WPS/PBC-enabled wireless client device during this time; if it succeeds, the wireless client device connects to your device, and the WPS LED turns off. Repeat steps mentioned above if you want to connect more wireless client devices to the device.
-55-
User Manual of WDAP-C7200AC
PIN：To use this option, you must know the PIN code from the wireless client and enter it in corresponding field on your device while using the same PIN code on client side for such connection.
The page includes the following fields:
Object
Disable WPS
Description
You can check the box to disable the WPS function.
WPS Status
Self-PIN Number
Here you can check if the connection via WPS is established or not.
It is the PIN number of the WDAP-C7200AC here.
Push Button
Configuration
Client PIN Number
Click the “Start PBC” to activate WPS as well in the client device within
2 minutes.
In addition to the PBC method, you can also use the PIN method to activate the WPS. Just enter the PIN number of the client device in the field and click the “Start PIN” button.
The WPS encryption can be implemented only between your Router and another
WPS-capable device.
Example of how to establish wireless connection using WPS. Please take the following steps:
Step 1. Choose menu “WLAN1 (5GHz) WPS” to configure the setting for WPS. After the configuration, please click the “Apply Changes” button to save the settings.
Step 2. Add a new device.
If the wireless adapter supports Wi-Fi Protected Setup (WPS), you can establish a wireless connection between wireless adapter and AP using either Push Button Configuration (PBC) method or PIN method.
To build a successful connection by WPS, you should also do the corresponding configuration of the new device for WPS function.
A. By Push Button Configuration (PBC)
-56-
i. Click the “Start PBC” Button on the WPS page of the AP.
User Manual of WDAP-C7200AC
Figure 5-42 WPS-PBC – 5GHz-1
Figure 5-43 WPS-PBC – 5GHz-2 ii. iii.
Press and hold the WPS Button equipped on the adapter directly for 2 or 3 seconds. Or you can click the WPS button with the same function in the configuration utility of the adapter. The process must be finished within 2 minutes.
Wait for a while until the next screen appears. Click OK to complete the WPS configuration.
If the new device supports Wi-Fi Protected Setup and the PIN method, you can add it to the network by PIN with the following two methods.
Method One: Enter the PIN of your Wireless adapter into the configuration utility of the AP i. Enter the PIN code of the wireless adapter in the field behind Client PIN Number in the following figure. Then click Start PIN.
The PIN code of the adapter is always displayed on the WPS configuration screen.
-57-
User Manual of WDAP-C7200AC
Figure 5-44 WPS-PIN – 5GHz-1
Figure 5-45 WPS-PIN – 5GHz-2 ii. For the configuration of the wireless adapter, please choose the option that you want to enter PIN
into the AP (Enrollee) in the configuration utility of the WPS and click Next until the process finishes.
Method Two: Enter the PIN of the AP into the configuration utility of your Wireless adapter i. Click the “Start PBC” Button on the WPS page of the AP. Get the Current PIN code of the AP in WPS page (each AP has its unique PIN code).
Figure 5-46 WPS-PIN – 5GHz-3 ii. For the configuration of the wireless adapter, please choose the option that you want to enter the PIN
of the AP (Registrar) in the configuration utility of the Wireless adapter and enter it into the field.
Then click Next until the process finishes.
-58-
User Manual of WDAP-C7200AC
5.3.9 Schedule
Wireless Schedules will enable or disable your wireless access at a set time based on your predefined schedule.
This feature is often used for restricting access to all users (such as children, employees and guests) during specific times of the day for parental control or security reasons.
Choose menu “WLAN1 (5GHz) Schedule” to configure the schedule rule of enabling wireless function. After the configuration, please click the “Apply Changes” button to save the settings.
Figure 5-47 Schedule - 5GHz
-59-
User Manual of WDAP-C7200AC
When setting the Wireless Schedule, it is important to ensure that your System Clock settings have been configured. If not, your Wireless Schedule will not function correctly.
5.4 WLAN2 (2.4GHz)
The Wireless menu contains submenus of the settings about wireless network. Please refer to the following sections for the details.
Figure 5-48 2.4GHz Wireless Main Menu
5.4.1 Basic Settings
Choose menu “WLAN2 (2.4GHz) Basic Settings” to configure the 2.4GHz basic settings for the wireless network on this page. After the configuration is done, please click the “Apply Changes” button to save the settings.
First of all, the wireless AP supports multiple wireless modes for different network applications, which include:
AP
Multiple SSIDs
Universal Repeater
Client
WDS
AP+WDS
It is so easy to combine the WDAP-C7200AC with the existing wired network. The WDAP-C7200AC definitely provides a total network solution for the home and the SOHO users.
AP
Standard Access Point
-60-
Internet
AP Mode
User Manual of WDAP-C7200AC
AP(Multi-SSID) Mode
WDAP-C7200AC
SSID-1(5G)
Clients
SSID-2(2.4G)
Clients
Figure 5-49 2.4GHz Wireless Basic Settings – AP
The page includes the following fields:
Object Description
Disable Wireless LAN
Interface
Check the box to disable the wireless function.
-61-
Band
Mode
SSID
Channel Width
Channel Number
Broadcast SSID
Data Rate
Associated Clients
User Manual of WDAP-C7200AC
Select the desired mode. Default is “2.4GHz (B+G+N)”. It is strongly recommended that you set the Band to “2.4GHz (B+G+N)”, and all of
802.11b, 802.11g, and 802.11n wireless stations can connect to the
WDAP-C7200AC.
2.4 GHz (B): 802.11b mode, rate is up to 11Mbps
2.4 GHz (G): 802.11g mode, rate is up to 54Mbps
2.4 GHz (N): 802.11n mode, rate is up to 300Mbps(2T2R)
2.4 GHz (B+G): 802.11b/g mode, rate is up to 11Mbps or 54Mbps
2.4 GHz (G+N): 802.11g/n mode, rate is up to 54Mbps or 300Mbps
2.4 GHz (B+G+N): 802.11b/g/n mode, rate is up to 11Mbps,
54Mbps, or 300Mbps
There are four kinds of wireless mode selections:
AP
Client
WDS
AP+WDS
If you select WDS or AP+WDS, please click “WDS Settings” submenu for the related configuration. Furthermore, click the “Multiple AP” button to enable multiple SSID function.
The ID of the wireless network. User can access the wireless network via the ID only. However, if you switch to Client Mode, this field becomes the SSID of the AP you want to connect with.
Default: Planet AP 2.4G
You can select 20MHz, or 40MHz.
You can select the operating frequency of wireless network.
Default: 11
If you enable “Broadcast SSID”, every wireless station located within the coverage of the AP can discover its signal easily. If you are building a public wireless network, enabling this feature is recommended. In private network, disabling “Broadcast SSID” can provide better wireless network security.
Default is “Enabled”.
Set the wireless data transfer rate to a certain value. Since most of wireless devices will negotiate with each other and pick a proper data transfer rate automatically, it’s not necessary to change this value
unless you know what will happen after modification.
Default is “Auto”.
Click the “Show Active Clients” button to show the status table of active wireless clients.
-62-
User Manual of WDAP-C7200AC
Enable Universal
Repeater Mode
(Acting as AP and client simultaneously)
Universal Repeater is a technology used to extend wireless coverage.
To enable Universal Repeater mode, check the box and enter the
SSID you want to broadcast in the field below. Then please click
“Security” submenu for the related settings of the AP you want to connect with.
Multiple-SSID
Enable multiple-SSID can broadcast multiple WLAN SSID's using virtual interfaces. You can have different encryption settings for each WLAN and you can restrict what they have access to.
Internet
AP(Multi-SSID) Mode
WDAP-C7200AC
SSID-1(5G)
Clients
SSID-2(2.4G)
AP Mode
Clients
Choose menu “
WLAN1 (2.4GHz) → Basic Settings → Multiple AP” to configure the device as a general wireless access point with multiple SSIDs.
Figure 5-50 2.4GHz Wireless Basic Settings – Multiple AP
The device supports up to four multiple Service Set Identifiers. You can back to the
Basic Settings page to set the Primary SSID. The SSID’s factory default setting is
Planet 2.4G VAP1~4 (Multiple-SSID 1~4). The
SSID can be easily changed to connect to an existing wireless network or to establish a new wireless network. When the information for the new SSID is finished, click the
Apply Changes button to let your changes take effect.
-63-
User Manual of WDAP-C7200AC
Figure 5-51 2.4GHz Multiple-SSID
Once you have applied and saved those settings, you can then go to the “
WLAN1 (2.4GHz) → Security” page on the AP to set up security settings for each of the SSIDs.
Universal Repeater
This mode allows the AP with its own BSS to relay data to a root AP to which it is associated with WDS disabled. The wireless repeater relays signal between its stations and the root AP for greater wireless range.
Universal Repeater Mode
WDAP-C7200AC
Internet a/n/ac a/n/ac
5G
g/n
Switch
Clients
2.4G
AP g/n
Smart Phone
2. Example of how to configure
Universal Repeater Mode. Please take the following steps:
To configure each wireless parameter, please go to the “
WLAN2 (2.4GHz) → Basic Settings” page.
Step 1. Configure wireless mode to “AP” and then check “Enable Universal Repeater Mode (Acting as AP
and client simultaneously)”. Click “Apply Changes” to take effect.
-64-
User Manual of WDAP-C7200AC
Figure 5-52 2.4GHz Universal Repeater-1
Step 2. Go to 2.4GHz Site Survey page to find the root AP. Select the root AP that you want to repeat the signal, and then click “Next”.
Figure 5-53 2.4GHz Universal Repeater-2
-65-
User Manual of WDAP-C7200AC
Step 3. Select the correct encryption method and enter the security key. Then, click “Connect”.
Figure 5-54 2.4GHz Universal Repeater-3
Step 4. Check “Add to Wireless Profile” and click “Reboot Now”.
Figure 5-55 2.4GHz Universal Repeater-4
Step 5. Go to “Management-> Status” page to check whether the state of Repeater interface should be
“Connected”.
Figure 5-56 2.4GHz Universal Repeater-5
-66-
User Manual of WDAP-C7200AC
Client (Infrastructure)
Combine the Wireless Router to the Ethernet devices such as TV, Game player, or HDD and DVD, to make them be wireless stations.
-67-
User Manual of WDAP-C7200AC
Figure 5-57 2.4GHz Wireless Basic Settings – Client
The page includes the following fields:
Object Description
Disable Wireless LAN
Interface
Check the box to disable the wireless function.
Band
Select the desired mode. Default is “2.4GHz (B+G+N)”. It is strongly recommended that you set the Band to “2.4GHz (B+G+N)”, and all of
802.11b, 802.11g, and 802.11n wireless stations can connect to the
WDAP-C7200AC.
2.4 GHz (B): 802.11b mode, rate is up to 11Mbps
2.4 GHz (G): 802.11g mode, rate is up to 54Mbps
2.4 GHz (N): 802.11n mode, rate is up to 300Mbps(2T2R)
-68-
Mode
Network Type
SSID
Broadcast SSID
Data Rate
User Manual of WDAP-C7200AC
2.4 GHz (B+G): 802.11b/g mode, rate is up to 11Mbps or 54Mbps
2.4 GHz (G+N): 802.11g/n mode, rate is up to 54Mbps or 300Mbps
2.4 GHz (B+G+N): 802.11b/g/n mode, rate is up to 11Mbps,
54Mbps, or 300Mbps
There are four kinds of wireless mode selections:
AP
Client
WDS
AP+WDS
If you select WDS or AP+WDS, please click “WDS Settings” submenu for the related configuration. Furthermore, click the “Multiple AP” button to enable multiple SSID function.
In Infrastructure, the wireless LAN serves as a wireless station. And the user can use the PC equipped with the WDAP-C7200AC to access the wireless network via other access points. In Ad hoc, the wireless
LAN will use the Ad-hoc mode to operate.
Default is “Infrastructure”.
Note: only while the wireless mode is set to “Client”, then the Network
Type can be configured.
The ID of the wireless network. User can access the wireless network via the ID only. However, if you switch to Client Mode, this field becomes the SSID of the AP you want to connect with.
Default: Planet AP 2.4G
If you enable “Broadcast SSID”, every wireless station located within the coverage of the WDAP-C7200AC can discover its signal easily. If you are building a public wireless network, enabling this feature is recommended. In private network, disabling “Broadcast SSID” can provide better wireless network security.
Default is “Enabled”.
Set the wireless data transfer rate to a certain value. Since most of wireless devices will negotiate with each other and pick a proper data transfer rate automatically, it’s not necessary to change this value
unless you know what will happen after modification.
Default is “Auto”.
Enable Mac Clone
(Single Ethernet Client)
Enable Mac Clone.
Example of how to configure Client Mode. Please take the following steps:
To configure each wireless parameter, please go to the “WLAN2 (2.4GHz) → Basic Settings” page.
-69-
User Manual of WDAP-C7200AC
Step 1. Go to “WLAN2 (2.4GHz) → Site Survey” page and click “Site Survey” button.
Figure 5-58 Client – Survey
-70-
User Manual of WDAP-C7200AC
Step 2. Choose the root AP from the list. If the root AP is not listed in the table, re-click “Site Survey” to update the list.
Figure 5-59 Client – AP List
Step 3. Enter the Security Key of the root AP and then click “Connect”.
-71-
User Manual of WDAP-C7200AC
Figure 5-60 Client – Security
Step 4. Wait until the connection established. Check the “Add to Wireless Profile” option and then reboot it.
Figure 5-61 Client – Status
WDS
Connect this Wireless AP with up to 8 WDS-capable wireless APs to expand the scope of network.
WDS Bridge-PtP Mode
Clients
WDAP-C7200AC WDAP-C7200AC
Switch Switch Clients
-72-
User Manual of WDAP-C7200AC
WDS Bridge-PtMP Mode
WDAP-C7200AC
AP
Switch Clients
Clients Switch
AP
Switch Clients
Figure 5-62 2.4GHz Wireless Basic Settings – WDS
-73-
User Manual of WDAP-C7200AC
The page includes the following fields:
Object Description
Disable Wireless LAN
Interface
Check the box to disable the wireless function.
Band
Mode
Select the desired mode. Default is “2.4GHz (B+G+N)”. It is strongly recommended that you set the Band to “2.4GHz (B+G+N)”, and all of
802.11b, 802.11g, and 802.11n wireless stations can connect to the
WDAP-C7200AC.
2.4 GHz (B): 802.11b mode, rate is up to 11Mbps
2.4 GHz (G): 802.11g mode, rate is up to 54Mbps
2.4 GHz (N): 802.11n mode, rate is up to 300Mbps(2T2R)
2.4 GHz (B+G): 802.11b/g mode, rate is up to 11Mbps or 54Mbps
2.4 GHz (G+N): 802.11g/n mode, rate is up to 54Mbps or 300Mbps
2.4 GHz (B+G+N): 802.11b/g/n mode, rate is up to 11Mbps,
54Mbps, or 300Mbps
There are four kinds of wireless mode selections:
AP
Client
WDS
AP+WDS
If you select WDS or AP+WDS, please click “WDS Settings” submenu for the related configuration. Furthermore, click the “Multiple AP” button to enable multiple SSID function.
Channel Width
Control Sideband
Channel Number
Data Rate
You can select 20MHz, or 40MHz
You can select Upper or Lower.
You can select the operating frequency of wireless network.
Set the wireless data transfer rate to a certain value. Since most of wireless devices will negotiate with each other and pick a proper data transfer rate automatically, it’s not necessary to change this value
unless you know what will happen after modification.
Default is “Auto”.
AP+ WDS
Connect this Wireless AP with up to 8 WDS-capable wireless APs, and connect another AP to provide service for all wireless stations within its coverage.
-74-
Internet
WDS Repeater Mode
User Manual of WDAP-C7200AC
AP a/n/ac
5G WDS
WDAP-C7200AC
2.4G
g/n
Clients a/n/ac g/n
Switch
Figure 5-63 2.4GHz Wireless Basic Settings – WDS+AP
-75-
User Manual of WDAP-C7200AC
The page includes the following fields:
Object Description
Disable Wireless LAN
Interface
Check the box to disable the wireless function.
Country
Select your region from the pull-down list.
This field specifies the region where the wireless function of the Router can be used. It may be illegal to use the wireless function of the Router in a region other than one of those specified in this field. If your country or region is not listed, please contact your local government agency for assistance.
Band
Select the desired mode. Default is “2.4GHz (B+G+N)”. It is strongly recommended that you set the Band to “2.4GHz (B+G+N)”, and all of
802.11b, 802.11g, and 802.11n wireless stations can connect to the
WDAP-C7200AC.
Mode
2.4 GHz (B): 802.11b mode, rate is up to 11Mbps
2.4 GHz (G): 802.11g mode, rate is up to 54Mbps
2.4 GHz (N): 802.11n mode, rate is up to 300Mbps(2T2R)
2.4 GHz (B+G): 802.11b/g mode, rate is up to 11Mbps or 54Mbps
2.4 GHz (G+N): 802.11g/n mode, rate is up to 54Mbps or 300Mbps
2.4 GHz (B+G+N): 802.11b/g/n mode, rate is up to 11Mbps,
54Mbps, or 300Mbps
There are four kinds of wireless mode selections:
AP
Client
WDS
AP+WDS
If you select WDS or AP+WDS, please click “WDS Settings” submenu for the related configuration. Furthermore, click the “Multiple AP” button to enable multiple SSID function.
SSID
Channel Width
Control Sideband
Channel Number
Broadcast SSID
The ID of the wireless network. User can access the wireless network via the ID only. However, if you switch to Client Mode, this field becomes the SSID of the AP you want to connect with.
Default: Planet AP 2.4G
You can select 20MHz, or 40MHz
You can select Upper or Lower.
You can select the operating frequency of wireless network.
If you enable “Broadcast SSID”, every wireless station located within the coverage of the WDAP-C7200AC can discover its signal easily. If you are building a public wireless network, enabling this feature is recommended. In private network, disabling “Broadcast SSID” can
-76-
User Manual of WDAP-C7200AC
provide better wireless network security.
Default is “Enabled”.
Data Rate
Set the wireless data transfer rate to a certain value. Since most of wireless devices will negotiate with each other and pick a proper data transfer rate automatically, it’s not necessary to change this value
unless you know what will happen after modification.
Associated Clients
Enable Universal
Repeater Mode
(Acting as AP and client simultaneously)
Default is “Auto”.
Click the “Show Active Clients” button to show the status table of active wireless clients.
Universal Repeater is a technology used to extend wireless coverage.
To enable Universal Repeater Mode, check the box and enter the
SSID you want to broadcast in the field below. Then please click
“Security” submenu for the related settings of the AP you want to connect with.
5.4.2 Advanced Settings
Choose menu “WLAN2 (2.4GHz) Advanced Settings” to configure the 2.4GHz advanced settings for the wireless network on this page. After the configuration, please click the “Apply” button to save the settings.
Figure 5-64 Wireless Advanced Settings – 2.4GHz
-77-
User Manual of WDAP-C7200AC
The page includes the following fields:
Object
Fragment Threshold
RTS Threshold
Beacon Interval
IAPP
Protection
Aggregation
Short GI
WLAN Partition
STBC
LDPC
20/40MHz Coexist
Description
You can specify the maximum size of packet during the fragmentation of data to be transmitted. If you set this value too low, it will result in bad performance.
Default is “2346”.
When the packet size is smaller than the RTS threshold, the access point will not use the RTS/CTS mechanism to send this packet.
Default is “2347”.
The interval of time that this access point broadcasts a beacon.
Beacon is used to synchronize the wireless network. Default is “100”.
IAPP (Inter-Access Point Protocol) enabled is recommended as it describes an optional extension to IEEE 802.11 that provides wireless access-point communications among multivendor systems.
Default is “Enabled”.
It is recommended to enable the protection mechanism. This mechanism can decrease the rate of data collision between 802.11b and 802.11g wireless stations. When the protection mode is enabled, the throughput of the AP will be a little lower due to the transmission of heavy frame traffic.
Default is “Disabled”.
It is a function where the values of multiple rows are grouped together.
Default is “Enabled”
It is used to set the time that the receiver waits for RF reflections to settle out before sampling data.
Default is “Enabled”
This feature also called “WLAN isolation” or “Block Relay”. If this is enabled, wireless clients cannot exchange data through the
WDAP-C7200AC.
Default is “Disabled”.
Activate Space Time Blocking Code (STBC) which does not need channel statement information (CSI).
Default Setting: "Enabled"
Low-density Parity-check Code is wireless data transmit algorithm.
Default Setting: "Enabled"
Configure 20/40MHz coexisting scheme.
If you set up as "Enabled", "20MHz" and "40MHz" will coexist.
Default Setting: "Disabled"
-78-
User Manual of WDAP-C7200AC
5.4.3 RF Output Power
Choose menu “WLAN2 (2.4GHz) RF Output Power” to adjust to different levels of transmitting power for the wireless network according to various environment on this page. After the configuration, please click the “Apply
Changes” button to save the settings.
Figure 5-65 RF Output Power – 2.4GHz
RF Output Power Control provides the flexibility to control the Wi-Fi Transmit power to optimize the wireless range. Wi-Fi power consumption for an Access Point could be reduced to up to 75% from its peak power consumption for serving small to medium size homes, while boosted to maximum power for large homes and businesses. The WDAP-C7200AC supports output power control levels up to 5. You can change the RF output power level here in accordance with various environments and signal strength.
-79-
User Manual of WDAP-C7200AC
5.4.4 Security
Choose menu “WLAN2 (2.4GHz) Security” to configure the settings of wireless security for the wireless network on this page. After the configuration, please click the “Apply Changes” button to save the settings.
Figure 5-66 Wireless Security Settings – 2.4GHz
The page includes the following fields:
Object
Select SSID
Encryption
Description
Select the SSID you want to configure the wireless security function, which includes the root one and the client one.
Disable:
No security setup for wireless connection.
WEP:
It is based on the IEEE 802.11 standard. And the default setting of authentication is Automatic, which can select Open System or Shared Key authentication type automatically based on the wireless station's capability and request. Furthermore, you can select Key Length and enter 10 and 26
Hexadecimal digits (any combination of 0-9, a-f, A-F, zero key is not promoted) or 5 and 13 ASCII characters in the Encryption Key field.
WPA:
WPA is a medium level encryption and is supported by most wireless devices and operating systems.
-80-
Authentication Mode
User Manual of WDAP-C7200AC
WPA2:
WPA2 is a high level encryption and is supported by most wireless devices and operating systems.
WPA / WPA2 / WPA-Mixed:
WPA Mixed Mode allows the use of both WPA and WPA2 at the same time.
Enterprise (RADIUS)
When you select the authentication mode based on Enterprise (Radius
Server), please enter the IP Address, Port, and Password of the Radius
Server.
Personal (Pre-Shared Key)
When you select the other authentication mode based on Personal
(Pre-Shared Key), please enter at least 8 ASCII characters (Passphrase) or
64 Hexadecimal characters. All of the Cipher Suites support TKIP and AES.
802.1x Authentication
Enable 802.1x authentication function and then enter the IP Address, Port, and Password of the Radius Server.
-81-
User Manual of WDAP-C7200AC
5.4.5 Access Control
Choose menu “WLAN2 (2.4GHz) Access Control” to allow or deny the computer of specified MAC address to connect with the WDAP-C7200AC on this page. After the configuration, please click the “Apply Changes” button to save the settings.
Figure 5-67 Wireless Access Control – 2.4GHz
The page includes the following fields:
Object
Wireless Access
Control Mode
MAC Address
Description
You can choose to set the Allowed-List, Denied-List, or disable this function.
Enter the MAC address you want to allow or deny connection to the
WDAP-C7200AC in the field.
You can make some comment on each MAC address on the list.
Comment
Current Access Control
List
You can select some MAC addresses and click the “Delete Selected” button to delete it.
Wireless Access Control example:
To deny a PC at the MAC address of 00:30:4F:00:00:01 to connect to your wireless network, do as follows:
Step 1. Select “Deny” from MAC Address Filter drop-down menu.
Step 2. Enter 00:30:4F:00:00:01 in the MAC address box and click “Add”.
-82-
User Manual of WDAP-C7200AC
Step 3. Click the “OK” button to save your settings and you can add more MAC addresses, if you like, simply repeat the above steps.
Figure 5-68 Wireless Access Control – Deny
-83-
User Manual of WDAP-C7200AC
5.4.6 WDS
WDS (Wireless Distribution System) feature can be used to extend your existing 2.4G or 5G wireless network coverage. Here we present you how to configure such feature in 2.4GHz, which also applies to 2.4GHz.
WDS Bridge-PtP Mode
WDAP-C7200AC WDAP-C7200AC
Clients Switch Switch Clients
WDS Bridge-PtMP Mode
WDAP-C7200AC
AP
Switch Clients
Clients Switch
AP
Switch Clients
WDS Repeater Mode
Internet
AP a/n/ac
5G WDS
WDAP-C7200AC
2.4G
g/n
Clients a/n/ac g/n
Switch
Before configuring the WDS Setting page, you have to select the wireless mode to “
WDS” on the WLAN2
(2.4GHz) -> Basic Settings web page.
-84-
User Manual of WDAP-C7200AC
Figure 5-69 WDS Mode – 2.4GHz
Choose menu “WLAN2 (2.4GHz) WDS Settings” to configure WDS to connect the WDAP-C7200AC with another AP on this page. After the configuration, please click the “Apply Changes” button to save the settings.
Figure 5-70 WDS Settings – 2.4GHz
-85-
User Manual of WDAP-C7200AC
The page includes the following fields:
Figure 5-71 WDS – Set Security
Object
Enable WDS
MAC Address
Data Rate
Comment
Set Security
Description
Check the box to enable the WDS function. Please select WDS or
AP+WDS in the Mode of Wireless Basic Settings before you enable
WDS on this page.
You can enter the MAC address of the AP you want to connect with.
Default is “Auto”.
You can make some comment for each MAC address on the list.
Click the “Set Security” button to configure the wireless security parameters of the AP you want to connect via WDS.
Click the “Show Statics” button to show the WDS AP.
Show Statics
Current WDS AP List
You can select some MAC addresses of the AP and click the “Delete
Selected” button to delete it.
WDS feature can only be implemented between 2 wireless devices that both support the
WDS feature. Plus, channel, security settings and security key must be the same on both such devices.
To encrypt your wireless network, click “Set Security”. For the detail of wireless security, see
. Do remember to reboot the device after you save your wireless
security settings; otherwise, the WDS feature may not function.
-86-
User Manual of WDAP-C7200AC
5.4.7 Site Survey
Choose menu “WLAN2 (2.4GHz) Site Survey” to scan the available local AP. If any Access Point is found, you could choose any one to connect with manually when the Client Mode is enabled.
Figure 5-72 Site Survey – 2.4GHz
5.4.8 WPS
WPS (Wi-Fi Protected Setup) is designed to ease setup of security Wi-Fi networks and subsequently network management. This Wireless Router supports WPS features for AP mode, AP+WDS mode,
Infrastructure-Client mode, and the wireless root interface of Universal Repeater mode.
Simply enter a PIN code or press the software PBC button or hardware WPS button (if any) and a secure wireless connection is established.
-87-
User Manual of WDAP-C7200AC
PBC: If you find the WPS LED blinking for 2 minutes after you press the hardware WPS button on the device, it means that PBC encryption method is successfully enabled. And an authentication will be performed between your router and the WPS/PBC-enabled wireless client device during this time; if it succeeds, the wireless client device connects to your device, and the WPS LED turns off. Repeat steps mentioned above if you want to connect more wireless client devices to the device.
PIN：To use this option, you must know the PIN code from the wireless client and enter it in corresponding field on your device while using the same PIN code on client side for such connection.
The page includes the following fields:
Object
Disable WPS
Description
You can check the box to disable the WPS function.
WPS Status
Self-PIN Number
Push Button
Configuration
Client PIN Number
Here you can check if the connection via WPS is established or not.
It is the PIN number of the WDAP-C7200AC here.
Click the “Start PBC” to activate WPS as well in the client device within
2 minutes.
In addition to the PBC method, you can also use the PIN method to activate the WPS. Just enter the PIN number of the client device in the field and click the “Start PIN” button.
The WPS encryption can be implemented only between your Router and another
WPS-capable device.
Example of how to establish wireless connection using WPS. Please take the following steps:
Step 1. Choose menu “WLAN2 (2.4GHz) WPS” to configure the setting for WPS. After the configuration, please click the “Apply Changes” button to save the settings.
Step 2. Add a new device.
If the wireless adapter supports Wi-Fi Protected Setup (WPS), you can establish a wireless connection between wireless adapter and AP using either Push Button Configuration (PBC) method or PIN method.
To build a successful connection by WPS, you should also do the corresponding configuration of the new device for WPS function.
-88-
A. By Push Button Configuration (PBC)
i. Click the “Start PBC” Button on the WPS page of the AP.
User Manual of WDAP-C7200AC
Figure 5-73 WPS-PBC – 2.4GHz-1 ii. iii.
Figure 5-74 WPS-PBC – 2.4GHz-2
Press and hold the WPS Button equipped on the adapter directly for 2 or 3 seconds. Or you can click the WPS button with the same function in the configuration utility of the adapter. The process must be finished within 2 minutes.
Wait for a while until the next screen appears. Click OK to complete the WPS configuration.
If the new device supports Wi-Fi Protected Setup and the PIN method, you can add it to the network by PIN with the following two methods.
Method One: Enter the PIN of your Wireless adapter into the configuration utility of the AP i. Enter the PIN code of the wireless adapter in the field behind Client PIN Number in the following figure and then click Start PIN.
The PIN code of the adapter is always displayed on the WPS configuration screen.
-89-
User Manual of WDAP-C7200AC
Figure 5-75 WPS-PIN – 2.4GHz-1
Figure 5-76 WPS-PIN – 2.4GHz-2 ii. For the configuration of the wireless adapter, please choose the option that you want to enter PIN
into the AP (Enrollee) in the configuration utility of the WPS and click Next until the process finishes.
Method Two: Enter the PIN of the AP into the configuration utility of your Wireless adapter i. Click the “Start PBC” Button on the WPS page of the AP. Get the Current PIN code of the AP in WPS page (each AP has its unique PIN code). ii.
Figure 5-77 WPS-PIN – 2.4GHz-3
For the configuration of the wireless adapter, please choose the option that you want to enter the PIN
of the AP (Registrar) in the configuration utility of the Wireless adapter and enter it into the field.
Then click Next until the process finishes.
-90-
User Manual of WDAP-C7200AC
5.4.9 Schedule
Wireless Schedules will enable or disable your wireless access at a set time based on your predefined schedule.
This feature is often used for restricting access to all users (such as children, employees and guests) during specific times of the day for parental control or security reasons.
Choose menu “WLAN2 (2.4GHz) Schedule” to configure the schedule rule of enabling wireless function.
After the configuration, please click the “Apply Changes” button to save the settings.
Figure 5-78 Schedule – 2.4GHz
-91-
User Manual of WDAP-C7200AC
When setting the Wireless Schedule, it is important to ensure that your System Clock settings have been configured. If not, your Wireless Schedule will not function correctly.
5.5 Management
This section focuses on how to maintain AP, including Restore to Factory Default Setting, Backup/Restore,
Firmware Upgrade, Reboot, Password Change and Syslog.
Figure 5-79 Management – Main Menu
5.5.1 Status
You can use this function to realize the instantaneous information of the Wireless AP. The Information displayed here may vary on different configurations.
Choose menu “Management Status” to show the current status and some basic settings of the
WDAP-C7200AC.
-92-
User Manual of WDAP-C7200AC
Figure 5-80 Status
5.5.2 Statistics
Choose menu “Management Statistics” to show the packet counters for transmission and reception regarding wireless and Ethernet network.
-93-
User Manual of WDAP-C7200AC
Figure 5-81 Statistics
The page includes the following fields:
Object
Wireless LAN
Sent Packets
Wireless LAN
Received Packets
Ethernet WAN
Sent Packets
Ethernet WAN
Received Packets
Refresh
5.5.3 NTP Settings
Description
It shows the statistic count of sent packets on the wireless LAN interface.
It shows the statistic count of received packets on the wireless LAN interface.
It shows the statistic count of sent packets on the Ethernet WAN interface.
It shows the statistic count of received packets on the Ethernet WAN interface.
Click the refresh the statistic counters on the screen.
This section assists you in setting the Wireless AP’s system time. You can either select to set the time and date manually or automatically obtain the GMT time from Internet.
Choose menu “Management NTP Settings” to configure the system time. You can also maintain the system time by synchronizing with a public time server over the Internet. After the configuration, please click the “OK” button to save the settings.
The configured time and date settings are lost when the Wireless AP is powered off.
-94-
User Manual of WDAP-C7200AC
The page includes the following fields:
Figure 5-82 Time Zone Settings
Object
Current Time
Time Zone Select
Input current time manually.
Description
You can click “Copy Computer Time” button to copy the PC’s current time to the AP.
Select the time zone of the country you are currently in. The router will set its time based on your selection.
Select the time offset, if your location observes daylight saving time.
Automatically Adjust
Daylight Saving
Enable NTP client update
NTP Server
Check to enable NTP update. Once this function is enabled, AP will automatically update current time from NTP server.
User may select prefer NTP sever or input address of NTP server manually.
-95-
User Manual of WDAP-C7200AC
If the AP loses power for any reason, it cannot keep its clock running, and will not have the correct time when it is started again. To maintain correct time for schedules and logs, either you must enter the correct time after you restart the AP, or you must enable the
NTP Server option.
5.5.4 Schedule Reboot
This page allows you to enable and configure system reboot schedule. The device can regularly reboot according to the reserved time when connecting to the Internet.
Figure 5-83 Schedule Reboot
The page includes the following fields:
Object
Schedule Reboot
Setting
Reboot Time
Reboot Plan
Description
Enable or disable the Schedule Reboot function.
Enter the Reboot Time (24-hour format) to enable this function to take effect.
There are two Reboot Plans supported in the AP:
Weekday: select this option to let the device reboot automatically according to the reserved time in one or more days of a week.
Every day: select this option to let the device reboot automatically according to the reserved time every day.
-96-
Weekday
User Manual of WDAP-C7200AC
Check one or more days to let the device auto reboot on schedule.
When choosing “Every day” as your reboot plan, the “Weekday” will be grayed out (disabled), which means Every day will auto reboot at the time that you scheduled.
1. This setting will only take effect when the Internet connection is accessible and the GMT time is configured correctly.
2. You must select at least one day when choosing “Weekday” as your reboot plan.
3. When choosing “Every day” as your reboot plan, the “Weekday” will be grayed out
(disabled), which means Every day will auto reboot at the time that you schedule.
Example of how to configure Schedule Reboot. Please take the following steps:
Before configured schedule reboots, please ensure the Internet connection is accessible and the GMT time is configured correctly according to NTP Settings page.
Step 1. Select the Schedule Reboot Setting checkbox.
Step 2. Enter the Reboot Time (24-hour format) to enable this function to take effect. For example, if you want this function to work at 23:00 every Sunday, choose "Weekday" in the Reboot Plan field.
Figure 5-84 Schedule Reboot - Example
Step 3. Click the “Apply Changes” button to take this function effect.
-97-
User Manual of WDAP-C7200AC
5.5.5 LOG
Choose menu “Management LOG” to configure the settings of system log. You can check the box of the items you want to record it in the log. After the configuration, please click the “Apply” button to save the settings.
Figure 5-85 System Log
The page includes the following fields:
Object
Enable Log Check to enable log function.
Description
System all
Wireless
Enable Remote Log
Check this option to display all the system logs.
Check this option to display only the logs related to wireless module.
Enable this option if you have a syslog server currently running on the LAN and wish to send log messages to it.
Enter the LAN IP address of the Syslog Server.
Log Server IP
Address
Refresh
Clear
Click this button to update the log.
Click this button to clear the current log.
-98-
User Manual of WDAP-C7200AC
5.5.6 Upgrade Firmware
This page allows you upgrade the Access Point firmware to new version. Please note, do not power off the device during the upload because it may crash the system.
Choose menu “Management Upgrade Firmware” to upgrade the firmware of the WDAP-C7200AC. Select the new firmware file downloaded from the PLANET website and then click “Upload” button to upgrade it.
The page includes the following fields:
Figure 5-86 Upgrade Firmware
Object
Select File
Description
Browse and select file you want to upgrade and press Upload to perform upgrade.
Please wait till the related information is shown on the screen after
upgrade is finished.
Do not disconnect the Wireless AP from your management PC (the PC you use to configure the device) or power off it during the upgrade process; otherwise, it may be permanently damaged. The Wireless AP will restart automatically when the upgrade process, which takes several minutes, to complete.
5.5.7 Reload Settings
Choose menu “Management Reload Settings” to back up or reset the configuration of the WDAP-C7200AC.
Once you have configured the Wireless AP the way you want it, you can save these settings to a configuration file on your local hard drive that can later be imported to your Wireless AP in case the device is restored to factory default settings.
-99-
User Manual of WDAP-C7200AC
The page includes the following fields:
Figure 5-87 Save/Reload Settings
Object Description
Save Settings to File
Click the “Save…” button to back up the configuration of the
WDAP-C7200AC and then save the “config.dat” in your computer.
Load Settings from File Select the configuration file of the WDAP-C7200AC and then click the
“Upload” button to reload the configuration back into the
WDAP-C7200AC.
Reset Settings to
Default
Click the “Reset” button to reset all settings of the WDAP-C7200AC to factory default.
Factory Default Settings:
User Name: admin
Password: admin
IP Address: 192.168.1.253
Subnet Mask: 255.255.255.0
Default Gateway: 192.168.1.254
DHCP: Disabled
5GHz SSID: Planet AP 5G
2.4GHz SSID: Planet AP 2.4G
Wireless Security: None
To activate your settings, you need to reboot the Wireless AP after you reset it.
-100-
User Manual of WDAP-C7200AC
5.5.8 Password
To ensure the Wireless AP’s security, you will be asked for your password when you access the Wireless AP’s
Web-based Utility. The default user name and password are “admin”. This page will allow you to add or modify the user name and password.
Choose menu “Management User Management” to change the user name and password which is inputted to access the web UI of the WDAP-C7200AC.
Figure 5-88 Password Setup
The page includes the following fields:
Object
User Name
Description
Enter user name.
Input password for this user.
New Password
Confirmed Password
Confirm password again.
For the sake of security, it is highly recommended that you change default login password and user name.
-101-
User Manual of WDAP-C7200AC
5.5.9 LED Control
This section allows the user to determine the router packets are talking to particular host.
Figure 5-89 LED Control
The page includes the following fields:
Object
Power LED
Position LED
Description
Click On or Off to turn on/off the Power LED.
The LED to detect and identify the AP.
1) Position LED on: the position LED is on.
2) Position LED blink: the position LED blinks continuously.
2) Position LED off: the position LED is off.
5.5.10 Logout
To logout the WDAP-C7200AC, please select “Logout” from the left-side menu.
Figure 5-90 Logout
-102-
User Manual of WDAP-C7200AC
Chapter 6. Quick Connection to a Wireless Network
In the following sections, the default SSID of the WDAP-C7200AC is configured to “default”.
6.1 Windows XP (Wireless Zero Configuration)
Step 1: Right-click on the wireless network icon displayed in the system tray
Figure 6-1 System Tray – Wireless Network Icon
Step 2: Select [View Available Wireless Networks]
Step 3: Highlight and select the wireless network (SSID) to connect
(1) Select SSID [default]
(2) Click the [Connect] button
Figure 6-2 Choose a wireless network
-103-
Step 4: Enter the encryption key of the Wireless AP
(1) The Wireless Network Connection box will appear
(2) Enter the encryption key that is configured in
(3) Click the [Connect] button
User Manual of WDAP-C7200AC
Figure 6-3 Enter the network key
Step 5: Check if “Connected” is displayed
Figure 6-4 Choose a wireless network -- Connected
-104-
User Manual of WDAP-C7200AC
Some laptops are equipped with a “Wireless ON/OFF” switch for the internal wireless LAN. Make sure the hardware wireless switch is switched to “ON” position.
6.2 Windows 7 (WLAN AutoConfig)
WLAN AutoConfig service is built-in in Windows 7 that can be used to detect and connect to wireless network.
This built-in wireless network connection tool is similar to wireless zero configuration tool in Windows XP.
Step 1: Right-click on the network icon displayed in the system tray
Figure 6-5 Network icon
Step 2: Highlight and select the wireless network (SSID) to connect
(1) Select SSID [default]
(2) Click the [Connect] button
Figure 6-6 WLAN AutoConfig
-105-
User Manual of WDAP-C7200AC
If you will be connecting to this Wireless AP in the future, check [Connect automatically].
Step 4: Enter the encryption key of the Wireless AP
(1) The Connect to a Network box will appear
(2) Enter the encryption key that is configured in
(3) Click the [OK] button
Figure 6-7 Type the network key
Figure 6-8 Connecting to a Network
Step 5: Check if “Connected” is displayed
-106-
User Manual of WDAP-C7200AC
Figure 6-9 Connected to a Network
-107-
Step 1: Right-click on the network icon displayed in the system tray
The AirPort Network Connection menu will appear
User Manual of WDAP-C7200AC
Figure 6-10 Mac OS – Network icon
Step 2: Highlight and select the wireless network (SSID) to connect
(1) Select and SSID [default]
(2) Double-click on the selected SSID
Figure 6-11 Highlight and select the wireless network
Step 4: Enter the encryption key of the Wireless AP
(1) Enter the encryption key that is configured in
(2) Click the [OK] button
-108-
User Manual of WDAP-C7200AC
Figure 6-12 Enter the Password
If you will be connecting to this Wireless AP in the future, check [Remember this
network].
Step 5: Check if the AirPort is connected to the selected wireless network.
If “Yes”, then there will be a “check” symbol in the front of the SSID.
Figure 6-13 Connected to the Network
-109-
User Manual of WDAP-C7200AC
There is another way to configure the MAC OS X Wireless settings:
Step 1: Click and open the [System Preferences] by going to Apple > System Preference or Applications
Figure 6-14 System Preferences
Step 2: Open Network Preference by clicking on the [Network] icon
Figure 6-15 System Preferences -- Network
-110-
User Manual of WDAP-C7200AC
Step 3: Check Wi-Fi setting and select the available wireless network
(1) Choose the AirPort on the left-menu (make sure it is ON)
(2) Select Network Name [default] here
If this is the first time to connect to the Wireless AP, it should show “Not network selected”.
Figure 6-16 Select the Wireless Network
-111-
Step 1: Tap the [Settings] icon displayed in the home screen
User Manual of WDAP-C7200AC
Figure 6-17 iPhone – Settings icon
Step 2: Check Wi-Fi setting and select the available wireless network
(3) Tap [General] \ [Network]
(4) Tap [Wi-Fi]
If this is the first time to connect to the Wireless AP, it should show “Not Connected”.
Figure 6-18 Wi-Fi Setting
-112-
User Manual of WDAP-C7200AC
Figure 6-19 Wi-Fi Setting – Not Connected
Step 3: Tap the target wireless network (SSID) in “Choose a Network…”
(1) Turn on Wi-Fi by tapping “Wi-Fi”
(2) Select SSID [default]
Figure 6-20 Turn on Wi-Fi
Step 4: Enter the encryption key of the Wireless AP
(1) The password input screen will be displayed
(2) Enter the encryption key that is configured in
(3) Tap the [Join] button
-113-
User Manual of WDAP-C7200AC
Figure 6-21 iPhone -- Enter the Password
Step 5: Check if the device is connected to the selected wireless network.
If “Yes”, then there will be a “check” symbol in the front of the SSID.
Figure 6-22 iPhone -- Connected to the Network
-114-
User Manual of WDAP-C7200AC
Appendix A: Planet Smart Discovery Utility
To easily list the WDAP-C7200AC in your Ethernet environment, the Planet Smart Discovery Utility from user’s manual CD-ROM is an ideal solution.
The following installation instructions guide you to running the Planet Smart Discovery Utility.
Step 1: Deposit the Planet Smart Discovery Utility in administrator PC.
Step 2: Run this utility and the following screen appears.
Step 3: Press “Refresh” button for the current connected devices in the discovery list as shown in the following screen:
Step 3: Press “Connect to Device” button and then the Web login screen appears.
The fields in white background can be modified directly and then you can apply the new setting by clicking the “Update Device” button.
-115-
User Manual of WDAP-C7200AC
Appendix B: Troubleshooting
If you find the AP is working improperly or stop responding to you, please read this troubleshooting first before contacting the dealer for help. Some problems can be solved by yourself within a very short time.
Scenario Solution
The AP is not responding to me when I want to access it by Web browser.
I can’t get connected to the
Internet. a. Please check the connection of the power cord and the
Ethernet cable of this AP. All cords and cables should be correctly and firmly inserted to the AP. b. If all LED on this AP is off, please check the status of power adapter, and make sure it is correctly powered. c. You must use the same IP address section which AP uses. d. Are you using MAC or IP address filter? Try to connect the AP by another computer and see if it works; if not, please reset the AP to the factory default settings
(pressing ‘reset’ button for over 7 seconds). e. Use the Smart Discovery Tool to see if you can find the
AP or not. f. If you did a firmware upgrade and this happens, contact your dealer of purchase for help. g. If all the solutions above don’t work, contact the dealer for help. a. Go to ‘Status’ -> ‘Internet Connection’ menu on the router connected to the AP, and check Internet connection status. b. Please be patient, sometimes Internet is just that slow. c. If you’ve connected a computer to Internet directly before, try to do that again, and check if you can get connected to Internet with your computer directly attached to the device provided by your Internet service provider. d. Check PPPoE / L2TP / PPTP user ID and password entered in the router’s settings again. e. Call your Internet service provider and check if there’s something wrong with their service. f. If you just can’t connect to one or more website, but you can still use other internet services, please check
URL/Keyword filter. g. Try to reset the AP and try again later. h. Reset the device provided by your Internet service provider too.
-116-
User Manual of WDAP-C7200AC
I can’t locate my AP by my wireless device.
File downloading is very slow or breaks frequently. i. Try to use IP address instead of host name. If you can use IP address to communicate with a remote server, but can’t use host name, please check DNS setting. a. ‘Broadcast ESSID’ set to off? b. Both two antennas are properly secured. c. Are you too far from your AP? Try to get closer. d. Please remember that you have to input ESSID on your wireless client manually, if ESSID broadcast is disabled.
a. Are you using QoS function? Try to disable it and try again. b. Internet is slow sometimes. Please be patient. c. Try to reset the AP and see if it’s better after that. d. Try to know what computers do on your local network. If someone’s transferring big files, other people will think
Internet is really slow. e. If this never happens before, call you Internet service provider to know if there is something wrong with their network.
I can’t log into the web management interface; the password is wrong. the AP! b. Password is case-sensitive. Make sure the ‘Caps Lock’ light is not illuminated. c. If you really forget the password, do a hard reset.
The AP becomes hot a. This is not a malfunction, if you can keep your hand on the AP’s case. b. If you smell something wrong or see the smoke coming out from AP or A/C power adapter, please disconnect the AP and power source from utility power (make sure it’s safe before you’re doing this!), and call your dealer of purchase for help.
-117-
User Manual of WDAP-C7200AC
Appendix C: Glossary
802.11ac
- 802.11ac is a wireless networking
standard in the
802.11
family (which is marketed under the brand name Wi-Fi), developed in the IEEE Standards Association process, providing high-throughput wireless local area networks
(WLANs) on the
5 GHz band
.
802.11n - 802.11n builds upon previous 802.11 standards by adding MIMO (multiple-input multiple-output). MIMO uses multiple transmitter and receiver antennas to allow for increased data throughput via spatial multiplexing and increased range by exploiting the spatial diversity, perhaps through coding schemes like Alamouti coding. The Enhanced Wireless Consortium (EWC) [3] was formed to help accelerate the IEEE 802.11n development process and promote a technology specification for interoperability of next-generation wireless local area networking (WLAN) products.
802.11a
-
802.11a was an amendment to the IEEE 802.11 wireless local network specifications that defined requirements for an orthogonal frequency division multiplexing (OFDM) communication system. It was originally designed to support wireless communication in the unlicensed national information infrastructure (U-NII) bands (in the 5–6 GHz frequency range) as regulated in the United
States by the Code of Federal Regulations, Title 47, Section 15.407.
802.11b - The 802.11b standard specifies a wireless networking at 11 Mbps using direct-sequence spread-spectrum (DSSS) technology and operating in the unlicensed radio spectrum at 2.4GHz, and
WEP encryption for security. 802.11b networks are also referred to as Wi-Fi networks.
802.11g - specification for wireless networking at 54 Mbps using direct-sequence spread-spectrum
(DSSS) technology, using OFDM modulation and operating in the unlicensed radio spectrum at
2.4GHz, and backward compatibility with IEEE 802.11b devices, and WEP encryption for security.
DDNS (Dynamic Domain Name System) - The capability of assigning a fixed host and domain name to a dynamic Internet IP Address.
DHCP (Dynamic Host Configuration Protocol) - A protocol that automatically configure the TCP/IP parameters for the all the PC(s) that are connected to a DHCP server.
DMZ (Demilitarized Zone) - A Demilitarized Zone allows one local host to be exposed to the Internet for a special-purpose service such as Internet gaming or videoconferencing.
DNS (Domain Name System) - An Internet Service that translates the names of websites into IP addresses.
Domain Name - A descriptive name for an address or group of addresses on the Internet.
DSL (Digital Subscriber Line) - A technology that allows data to be sent or received over existing traditional phone lines.
ISP (Internet Service Provider) - A company that provides access to the Internet.
-118-
User Manual of WDAP-C7200AC
MTU (Maximum Transmission Unit) - The size in bytes of the largest packet that can be transmitted.
NAT (Network Address Translation) - NAT technology translates IP addresses of a local area network to a different IP address for the Internet.
PPPoE (Point to Point Protocol over Ethernet) - PPPoE is a protocol for connecting remote hosts to the Internet over an always-on connection by simulating a dial-up connection.
SSID - A Service Set Identification is a thirty-two character (maximum) alphanumeric key identifying a wireless local area network. For the wireless devices in a network to communicate with each other, all devices must be configured with the same SSID. This is typically the configuration parameter for a wireless PC card. It corresponds to the ESSID in the wireless Access Point and to the wireless network name.
WEP (Wired Equivalent Privacy) - A data privacy mechanism based on a 64-bit or 128-bit or 152-bit shared key algorithm, as described in the IEEE 802.11 standard.
Wi-Fi - A trade name for the 802.11b wireless networking standard, given by the Wireless Ethernet
Compatibility Alliance (WECA, see http://www.wi-fi.net), an industry standards group promoting interoperability among 802.11b devices.
WLAN (Wireless Local Area Network) - A group of computers and associated devices communicate with each other wirelessly, which network serving users are limited in a local area.
-119-
User Manual of WDAP-C7200AC
EC Declaration of Conformity
English
Česky
Lietuviškai
Hereby, PLANET Technology Corporation, declares that this 11ac Wireless AP is in compliance with the essential requirements and other relevant provisions of Directive 1999/5/EC.
Společnost PLANET Technology Corporation, tímto prohlašuje, že tato 11ac Wireless AP splňuje základní požadavky a další příslušná ustanovení směrnice 1999/5/EC.
Magyar
Dansk
Deutsch
Eestikeeles
PLANET Technology Corporation, erklærer herved, at følgende udstyr 11ac Wireless AP overholder de væsentlige krav og øvrige relevante krav i direktiv 1999/5/EF
Malti
Hiermit erklärt PLANET Technology Corporation, dass sich dieses Gerät 11ac Wireless AP in
Übereinstimmung mit den grundlegenden
Anforderungen und den anderen relevanten
Vorschriften der Richtlinie 1999/5/EG befindet".
(BMWi)
Nederlands
Polski
Käesolevaga kinnitab PLANET Technology
Corporation, et see 11ac Wireless AP vastab
Euroopa Nõukogu direktiivi 1999/5/EC põhinõuetele ja muudele olulistele tingimustele.
Ελληνικά
Español
Français
Italiano
Latviski
ΜΕ ΤΗΝ ΠΑΡΟΥΣΑ , PLANET Technology
Corporation, ΔΗΛΩΝΕΙ ΟΤΙ ΑΥΤΟ 11ac Wireless
APΣΥΜΜΟΡΦΩΝΕΤΑΙ ΠΡΟΣ ΤΙΣ ΟΥΣΙΩΔΕΙΣ
ΑΠΑΙΤΗΣΕΙΣ ΚΑΙ ΤΙΣ ΛΟΙΠΕΣ
ΣΧΕΤΙΚΕΣ ΔΙΑΤΑΞΕΙΣ ΤΗΣ ΟΔΗΓΙΑΣ 1999/5/ΕΚ
Por medio de la presente, PLANET Technology
Corporation, declara que 11ac Wireless AP cumple con los requisitos esenciales y cualesquiera otras disposiciones aplicables o exigibles de la Directiva 1999/5/CE
Par la présente, PLANET Technology
Corporation, déclare que les appareils du 11ac
Wireless AP sont conformes aux exigences essentielles et aux autres dispositions pertinentes de la directive 1999/5/CE
Con la presente , PLANET Technology
Corporation, dichiara che questo 11ac Wireless
AP è conforme ai requisiti essenziali ed alle altre disposizioni pertinenti stabilite dalla direttiva
1999/5/CE.
Português
Slovensky
Slovensko
Suomi
Svenska
Ar šo PLANET Technology Corporation, apliecina, ka šī 11ac Wireless AP atbilst
Direktīvas 1999/5/EK pamatprasībām un citiem atbilstošiem noteikumiem.
Šiuo PLANET Technology Corporation,, skelbia, kad 11ac Wireless AP tenkina visus svarbiausius
1999/5/EC direktyvos reikalavimus ir kitas svarbias nuostatas.
A gyártó PLANET Technology Corporation, kijelenti, hogy ez a 11ac Wireless AP megfelel az 1999/5/EK irányelv alapkövetelményeinek és a kapcsolódó rendelkezéseknek.
Hawnhekk, PLANET Technology Corporation, jiddikjara li dan 11ac Wireless AP jikkonforma mal-ħtiġijiet essenzjali u ma provvedimenti oħrajn relevanti li hemm fid-Dirrettiva 1999/5/EC
Hierbij verklaart , PLANET Technology orporation, dat
11ac Wireless AP in overeenstemming is met de essentiële eisen en de andere relevante bepalingen van richtlijn 1999/5/EG
Niniejszym firma PLANET Technology Corporation, oświadcza, że 11ac Wireless AP spełnia wszystkie istotne wymogi i klauzule zawarte w dokumencie
„Directive 1999/5/EC”.
PLANET Technology Corporation, declara que este
11ac Wireless AP está conforme com os requisitos essenciais e outras disposições da Directiva
1999/5/CE.
Výrobca PLANET Technology Corporation, týmto deklaruje, že táto 11ac Wireless AP je v súlade so základnými požiadavkami a ďalšími relevantnými predpismi smernice 1999/5/EC.
PLANET Technology Corporation, s tem potrjuje, da je ta 11ac Wireless AP skladen/a z osnovnimi zahtevami in ustreznimi določili Direktive 1999/5/EC.
PLANET Technology Corporation, vakuuttaa täten että 11ac Wireless AP tyyppinen laite on direktiivin
1999/5/EY oleellisten vaatimusten ja sitä koskevien direktiivin muiden ehtojen mukainen.
Härmed intygar, PLANET Technology Corporation, att denna 11ac Wireless AP står i överensstämmelse med de väsentliga egenskapskrav och övriga relevanta bestämmelser som framgår av direktiv
1999/5/EG.
-120-
Advertisement
