Gold Medal SKES1 Equipment Accessories & Supplies Starter Package Owner's Manual
Gold Medal SKES1 is a commercial-grade ice shaver designed for producing large quantities of fluffy, shaved ice. Equipped with a powerful motor and durable stainless-steel blades, it can effortlessly handle large blocks of ice, making it ideal for busy concession stands, restaurants, and catering businesses. Its compact size and countertop design allow for easy placement and operation in any food preparation area.
Advertisement
Advertisement
Instruction Manual
© 2023 Gold Medal Products Co.
Sno-King
Model No. 1888 Series
Door and Cup Dispenser options sold separately.
10700 Medallion Drive, Cincinnati, Ohio 45241-4807 USA
Part No. 110319
Sno-King Model No. 1888 Series
Table of Contents
THE FOLLOWING SECTIONS ARE FOR QUALIFIED SERVICE PERSONNEL ONLY
Set Blade Height ............................................................................................................................................ 13
Page 2 gmpopcorn.com
Sno-King Model No. 1888 Series
SAFETY PRECAUTIONS
DANGER
Machine must be properly grounded to prevent electrical shock to personnel.
Failure to do so could result in serious injury, or death.
Make sure all machine switches are in the OFF position before plugging the equipment into the receptacle. Keep cord and plug off the ground and away from moisture. Always unplug the equipment before cleaning or servicing.
DO NOT immerse any part of this equipment in water.
DO NOT use a water jet or excessive water when cleaning.
008_012221
DANGER
Improper installation, adjustment, alteration, service, or maintenance can cause property damage, injury, or death. Any alterations to this equipment will void the warranty and may cause a dangerous condition. This appliance is not intended to be operated by means of an external timer or separate remote-control system. NEVER make alterations to this equipment. Read the
Installation, Operating, and Maintenance Instructions thoroughly before installing, servicing, or operating this equipment.
014_020416
WARNING
This machinery contains sharp blades. Keep hands and body parts clear at all times.
037_103114
WARNING
NEVER put your fingers into the shaver body (the goose-neck, ice chute, or hopper). Serious injury may occur.
017_103114
WARNING
ALWAYS wear safety glasses when servicing this equipment.
010_010914
WARNING
No user serviceable parts inside. Refer servicing to qualified service personnel.
011_051514
Page 3 gmpopcorn.com
Sno-King Model No. 1888 Series
WARNING
Read and understand operator’s manual and all other safety instructions before using this equipment. To order copies of the operator’s manual go to gmpopcorn.com or write to Gold Medal Products Co., 10700 Medallion Drive,
Cincinnati, OH 45241 USA 1-(800)-543-0862
022_060215
WARNING
DO NOT allow direct contact of this equipment by the public when used in food service locations. Only personnel trained and experienced in the equipment operation may operate this equipment.
Carefully read all instructions before operation.
012_010914
WARNING
This machine is NOT to be operated by minors.
007_010914
CAUTION
If the supply cord is damaged, it must be replaced by Gold Medal Products Co., its service agent or similarly qualified persons in order to avoid a hazard.
039_080614
This appliance is not intended for use by persons (including children) with reduced physical, sensory or mental capabilities, or lack of experience and knowledge, unless they have been given supervision or instruction concerning use of the appliance by a person responsible for their safety.
DO NOT install equipment in an area where a water jet is used.
Unit to be installed in locations where ambient temperatures are between a minimum of
5°C (41°F) and a maximum of 55°C (131°F).
Unit to be installed in locations where it can be overseen by trained personnel.
Install unit on a level surface.
Unit is for shaved ice.
Note: Improvements are always being made to Gold Medal’s equipment. This information may not be the latest available for your p urposes. It is critical that you call Gold Medal’s
Technical Service Department at 1-800-543-0862 for any questions about your machine operations, replacement parts, or any service questions. (Gold Medal
Products Co. does not assume any liability for injury due to careless handling and/or reckless operation of this equipment.) General images may be used in manual for reference only.
Page 4 gmpopcorn.com
Sno-King Model No. 1888 Series
INSTALLATION INSTRUCTIONS
Inspection of Shipment
After unpacking, check thoroughly for any damage which may have occurred in transit. Claims should be filed immediately with the transportation company. The warranty does not cover damage that occurs in transit, or damage caused by abuse, or consequential damage due to the operation of this machine, since it is beyond our control (reference warranty in back of manual).
Manual
Read and understand the operator’s manual and all other safety instructions before using this equipment. To order copies of the operator’s manual go to gmpopcorn.com or write to Gold
Medal Products Co., 10700 Medallion Drive, Cincinnati, OH 45241 USA 1-(800)-543-0862.
Model Description
1888 Series: Sno-King Ice Shaver.
Items Included with this Unit
• Plastic Snow Dipper (PN 1088)
• Ice Scoop (PN 39068)
• Drain Hose (PN 22034, order by the foot)
• Hose Clamp (PN 67843)
• Manual and Registration/Warranty Card
Setup
1.
Remove all packing material and tape before starting operation.
2.
Place unit on a sturdy, level base which can withstand accidental dripping of water and ice.
3.
Connect drain hose using the hose clamp provided, see image below. Drain hose funnels excess water to floor drain or basin tub. When in use, ensure the hose is positioned so water drains appropriately. Drained water is not intended for consumption.
4.
Install any optional accessories, if applicable (see Optional Accessories section).
5.
After setup, the unit should be cleaned prior to use (see Care and Cleaning section).
Page 5
Connect Drain Hose to fitting using Hose
Clamp provided. gmpopcorn.com
Sno-King Model No. 1888 Series
Electrical Requirements
The following power supply must be provided (reference unit Data Plate for Wattage requirement):
1888-00-100: 120 V~, 60 Hz
1888-01-100: 220-230 V~, 50/60 Hz
DANGER
Machine must be properly grounded to prevent electrical shock to personnel.
Failure to do so could result in serious injury, or death.
Make sure all machine switches are in the OFF position before plugging the equipment into the receptacle. Keep cord and plug off the ground and away from moisture. Always unplug the equipment before cleaning or servicing.
DO NOT immerse any part of this equipment in water.
DO NOT use a water jet or excessive water when cleaning.
008_012221
A certified electrician must furnish sufficient power for proper machine operation and install any supplied receptacle (reference unit Data Plate for model specific Volts AC, Hertz, and Wattage requirements). We recommend this equipment be on a dedicated and protected circuit. Failure to wire properly will void the warranty and may result in damage to the machine. It is Gold Medal
Products Co.’s recommendation that this machine be plugged directly into a wall outlet. The use of extension cords is not recommended due to safety concerns, and may cause sacrificed and/or reduced performance. Make sure cord is located to prevent a trip hazard or unit upset.
Before You Plug In Machine
1.
Make sure all machine switches are OFF before plugging equipment into receptacle.
2.
Make sure wall outlet can accept the grounded plugs (where applicable) on the power supply cord.
3.
The wall outlet must have the proper polarity. If in doubt, have a competent electrician inspect the outlet and correct if necessary.
4.
DO NOT use a grounded to un-grounded receptacle adapter (where applicable).
5.
Install unit in a level position.
CAUTION
If the supply cord is damaged, it must be replaced by Gold Medal Products Co., its service agent or similarly qualified persons in order to avoid a hazard.
039_080614
Page 6 gmpopcorn.com
Sno-King Model No. 1888 Series
Optional Accessories for
1888 (100) Series
Model 1888CD Cup Dispenser
The Cup Dispenser is available for purchase separately.
Empty the ice shaver before installing the dispenser kit; turn the power switch OFF and unplug the unit.
Cup Dispenser
Items included: Dispenser with lid and mount brackets; (2) 8-32 screws and (2) lock nuts.
Tools required (not included) : Screwdriver and adjustable wrench, drill and 7/32” bit.
Door Kit
(see next page)
When installation is complete, remove all drill shavings from cabinet and drain (do not let shavings run into drain hose), then thoroughly clean unit for use.
Align bracket with edge.
Lock
Nut
Mark BOTH holes.
1. Hold Mounting Bracket in position, then mark both holes for drilling.
2. Drill hole locations using 7/32 ” bit.
10-24 Screws Backing Plate
3.
Install both screws through bracket and backing plate, then fasten with lock nut.
Wide end of bracket goes UP.
V-Bracket (from cup dispenser)
8-32 Screw and
8-32 Lock Nut
4.
Install both screws through bracket and backing plate, then fasten with lock nut. 5.
Slide dispenser onto v-bracket as shown.
Page 7 gmpopcorn.com
Sno-King Model No. 1888 Series
Model 1888DR Door Kit
The Door Kit is available for purchase separately. Empty the ice shaver before installing the door kit; turn the power switch OFF and unplug the unit.
Items included: Door with handle; 3 shoulder bolts; 6 washers; 3 lock nuts.
Tools required (not included) : 3/16” Allen wrench and adjustable wrench, drill and 1/4” bit.
1.
Find dimple location for each hanger position, see image.
2.
Drill a hole at each location using 1/4” bit.
3.
Install fasteners as shown.
Dimple location for hole.
4.
Bottom edge of door slides down into cabinet, top door flanges sit on shoulder bolts.
Dimple location for hole.
Installed door rests on BOTH bolts.
Shoulder Bolt and Washer
Washer and
Lock Nut
Slide bottom edge down into cabinet.
Install Door Hanger
(holds door when not in use)
5.
Locate position for door hanger (shoulder bolt).
6.
Drill hole for shoulder bolt installation using 1/4” bit.
7.
Install fasteners (reference
Step 3 above).
Approx. 1”
8.
When installation is complete, remove all drill shavings from cabinet and drain (do not let shavings run into drain hose), then thoroughly clean unit for use.
Approx. 1”
Find hole location to drill.
Page 8 gmpopcorn.com
Sno-King Model No. 1888 Series
OPERATING INSTRUCTIONS
Controls and Their Functions
POWER SWITCH
Lighted Rocker Switch – supplies power to the momentary button switch.
MOMENTARY SWITCH
Momentary Switch must be engaged for unit to operate. Press switch to operate/energize the shaver motor; release the switch to de-energize the motor.
ICE HOPPER/PUSHER CAP
The hopper holds ice and funnels it to the shaver blades. Pusher Cap presses ice into the shaver blades.
Pusher Cap
Momentary
Switch
Power Switch
Ice Hopper
Ice Requirements
The shaver accepts ice cubes or block ice (if broken into pieces approximately 2 to 3 inches in size). The ice will not enter the shaving chute if the pieces are too large.
Note: Harder ice will result in finer snow; soft ice will result in coarser snow.
Operating Instructions
1.
Raise hopper lid (pusher cap) and load hopper with ice.
2.
Close pusher cap and apply gentle downward pressure.
3.
Turn on the power switch.
4.
Press and hold the momentary switch until all ice in hopper has been shaved, then release the button.
5.
DO NOT lift the pusher cap until the motor is off and the shaver head has stopped.
Note: Never allow any foreign or metallic objects around the shaver area. Ice picks, scoops, and debris that may be in the ice often damage blades.
Page 9 gmpopcorn.com
Sno-King Model No. 1888 Series
Care and Cleaning
DANGER
Machine must be properly grounded to prevent electrical shock to personnel.
DO NOT immerse in water. DO NOT clean appliance with a water jet or steam cleaner. Always unplug the equipment before cleaning or servicing.
025_051321
WARNING
This machinery contains sharp blades. Keep hands and body parts clear at all times.
037_103114
Good sanitation practice demands that all food preparation equipment be cleaned regularly (only use non-toxic, food grade cleaners).
Follow the directions below to clean and sanitize the unit each day after use.
1.
With the machine OFF, unplug the unit before attempting to clean.
2.
Empty water from pans and clean using appropriate cleaners for the type of machine; review all manufacturer’s instructions and warnings on cleaning product prior to use.
DO NOT use oven cleaners or abrasive materials as they will damage parts of the machine.
DO NOT use Ammonia cleaners, they will damage plastic panels.
Page 10 gmpopcorn.com
Sno-King Model No. 1888 Series
THE FOLLOWING SECTIONS ARE FOR QUALIFIED SERVICE PERSONNEL ONLY
MAINTENANCE INSTRUCTIONS
DANGER
Machine must be properly grounded to prevent electrical shock to personnel.
Failure to do so could result in serious injury, or death.
Make sure all machine switches are in the OFF position before plugging the equipment into the receptacle. Keep cord and plug off the ground and away from moisture. Always unplug the equipment before cleaning or servicing.
DO NOT immerse any part of this equipment in water.
DO NOT use a water jet or excessive water when cleaning.
008_012221
DANGER
Improper installation, adjustment, alteration, service, or maintenance can cause property damage, injury, or death. Any alterations to this equipment will void the warranty and may cause a dangerous condition. This appliance is not intended to be operated by means of an external timer or separate remote-control system. NEVER make alterations to this equipment. Read the
Installation, Operating, and Maintenance Instructions thoroughly before installing, servicing, or operating this equipment.
014_020416
WARNING
No user serviceable parts inside. Refer servicing to qualified service personnel.
011_051514
CAUTION
THE FOLLOWING SECTIONS OF THIS MANUAL ARE INTENDED ONLY
FOR QUALIFIED SERVICE PERSONNEL WHO ARE FAMILIAR WITH
ELECTRICAL EQUIPMENT. THESE ARE NOT INTENDED FOR THE
OPERATOR.
027_010914
Page 11 gmpopcorn.com
Sno-King Model No. 1888 Series
Installing New Shaver Blades
WARNING
This machinery contains sharp blades. Keep hands and body parts clear at all times.
037_103114
Prior to blade inspection or replacement, ALWAYS turn the machine OFF and unplug it from the power supply. Use a flashlight to examine the blades in the shaver body. If the blades appear to be nicked or bent, then they should be replaced.
Blade Replacement
1.
With the machine OFF, unplug the unit from the power supply.
2.
Remove motor cover (keep all fasteners as they will be used to reinstall the cover).
3.
Use a permanent marker and put a guide mark on the motor shaft where the shaver head stops; also place a small guide mark on the cabinet where the motor sets (reference shaver cut away view on next page).
4.
To remove the shaver head from the motor shaft, loosen the motor mounting bolts. (If unit has a hopper support and guide, it must also be removed).
5.
Pull motor back until the (2) Allen head set screws on the shaver head are visible.
Loosen the (2) set screws (do not remove set screws).
6.
Carefully guide the shaver head off of the motor shaft and through the hopper. If the shaver head is frozen to the shaft, pull the motor back trapping the shaver head against the inside of the hopper, until the shaver head disengages.
7.
After removing the shaver head, check the motor shaft for burrs and corrosion
(use a fine tooth file to remove any burrs or corrosion).
8.
Remove blades from shaver head. Replace old blades with a new set (blades may be re-sharpened).
9.
Position new blades on shaver head and insert blade mounting screws until finger tight.
10.
Set the blade thickness to 1/32” using a height gauge (thickness of a dime), reference Set Blade Height illustration shown on next page. Make sure the blade height is even across the shaver head.
11.
Tighten the blade mounting screws completely. Check the blade height again to ensure the blades did not move while tightening the screws.
12.
Carefully guide the shaver head through the hopper and back onto the motor shaft; realign head with guide mark made on the shaft in Step 3 above. (The pusher handle may be used to help press the shaver head onto the shaft.)
13.
The shaver head set screws must be on the flat side of the motor shaft. Once aligned, fasten set screws securely.
Page 12 gmpopcorn.com
Sno-King Model No. 1888 Series
14.
Adjust the motor to realign with guide mark made on the cabinet in Step 3, then refasten motor mounting bolts (if unit has a hopper support and guide, it must also be reinstalled). Check the shaver head to make sure it is not rubbing against the back of the hopper and the blades are not touching the pusher handle or sides of hopper; adjust as needed.
NOTE: Replace any shims that were between the motor base and the mounting surface.
15.
Reinstall motor cover.
Cut Away View of Shaver Head on Motor Shaft
General shaver image shown for reference only (models may vary).
Shaver Head
With a permanent marker, mark shaft where shaver head stops.
Motor
Mounting
Bolts
(2) Set Screws (fasten on flat side of motor shaft)
Set Blade Height
Set top of blade flush with height gauge, as shown.
With a permanent marker, mark cabinet where motor sets.
Height Gauge 1/32”
(thickness of a dime)
Shaver Head
Page 13
Shaver Blade
Blade Mounting Screw gmpopcorn.com
Sno-King Model No. 1888 Series
ORDERING SPARE PARTS
1.
Identify the needed part by checking it against the photos, illustrations, and/or parts list. (General images may be used in manual for reference only.)
2.
Use only approved replacement parts when servicing this unit.
3.
When ordering, please include part number, part name, and quantity needed.
4.
Please include your model number, serial number, and date of manufacture (located on the machine nameplate/data plate) with your order.
5.
Address all parts orders to Parts Department, Gold Medal Products Co., 10700
Medallion Drive, Cincinnati, Ohio 45241-4807 or place orders by phone or online:
Phone: (800) 543-0862
(513) 769-7676
Fax: (800) 542-1496
(513) 769-8500
E-mail: [email protected]
Web Page: gmpopcorn.com
Page 14 gmpopcorn.com
Sno-King Model No. 1888 Series
Cabinet and Controls View
5, 6, 7 4 8
Dome (molded housing only)
1
2
3
13
15
14
9
12
11
Hose Fitting (see above for Hose and Clamp)
10
Item Part Description
1
MOTOR COVER (molded housing only, switch boxes not included)
2 MOMENTARY SWITCH
3 SWITCH LIGHTED ROCKER
4 PLUNGER
5 PIVOT ROD
6 5-16 X 18 HEX NUT
7 5/16 FLAT WASHER ZINC PLT
8 WARNING LABEL
9 GUARD WARNING LABEL
10 UNIV WARN LBL HORZ
11 DRAIN FITTING
12 ICE SCOOP
13 PLASTIC SNOW DIPPER
14 DRAIN HOSE 3/8 ID 1/16 W (order by the foot)
15 HOSE CLAMP
Part Number
1888-00-100 1888-01-100
121166 121166
38971
42798
12662
12670
12001
74134
44018
44027
115180
121079
39068
1088
22034
75220
38971
42798
12662
12670
12001
74134
44018
44027
115180
121079
39068
1088
22034
75220
Page 15 gmpopcorn.com
Sno-King
Cabinet Parts Breakdown
Model No. 1888 Series
*CAUTION : If supply cord is damaged, it must be replaced by Gold Medal Products Co., its service agent, or similarly qualified persons in order to avoid a hazard.
1*
7
12
2
13
14
7, 8
5, 6
9
15
16
8
3
17
10 11
2
4
Dome Interior View
21
22
Page 16
25
26
18
16
19
20
23
24 gmpopcorn.com
Sno-King Model No. 1888 Series
Shaver Head and Accessories
28
27
29
Blade Set (includes washers and screws, see parts table)
Cabinet Parts - Shaver Head
—Parts List
Item Part Description
1* LEAD IN CORD
2 STRAIN RELIEF SR-6P3-4
3 JUNCTION BOX COVER
4 SCREW #8-32X3/8 PAN HD PH
5 8-32 X 3/8 PAN HD PH M/S
6 8-32 SERRATED FLANGE NUT
7 8-32 X 1/2 PHIL PN M/S SS
8 8-32 HEX NUT, ESLOK, S.S.
9 3” FAN GRATE
10 8-32 X 3/4 PHIL PAN MS SS
11 #8 WASHER 1/2IN OD
12 #10 FLAT WASHER ST. STL.
13 HOPPER SUPPORT GUIDE
14 HOPPER SUPPORT
15 5-16 X 18 HEX NUT
16 5/16 FLAT WASHER ZINC PLT
17 1/4 HP MOTOR
18 MOTOR WASHER PLATE
19 5/16-18 x 1 1/4 HEX HEAD
20 PUSH IN RIVET 1/4 X 1/2
21 FRONT WINDOW
22 NYLON BARBED TUBE FITTING
23 FENDER WASHER
24 FOOT, 1 IN 1888
25 1/4-20X3/4 SOCKET HD BOLT
26 CRUTCH TIP,1 IN I.D.
27 SHAVER HEAD
28 SET SCREW 1/4-20 X 3/8
29
2 HOLE BLADE REPLACE SET (includes 2 blades, washers, and screws)
Part Number
1888-00-100 1888-01-100
22038 42369
12685
12583
121078
121077
121079
82634
102264
12431
102266
22015
74125
76026
121166
74141
12389
61151
42226
22070
74746
39007
121220
12178
22233
12819
12001
74134
55448
12685
12583
121078
121077
121079
82634
102264
12431
102266
22015
74125
76026
121166
74141
12389
61151
42226
22070
74746
39007
121220
12178
22233
12819
12001
74134
113002
22017 22017
Page 17 gmpopcorn.com
Sno-King Model No. 1888 Series
Wiring Diagram
Model 1888-00-100 and 1888-01-100
Page 18 gmpopcorn.com
Sno-King Model No. 1888 Series
WARRANTY
WARRANTY
Gold Medal Products Co. warrants to the original purchaser each item of its manufacture to be free of defects in workmanship and material under normal use and service. Gold Medal Products Co.’s obligation under this warranty is limited solely to repairing or replacing parts, f.o.b. Cincinnati,
Ohio, which in its judgment are defective in workmanship or material and which are returned, freight prepaid, to its Cincinnati, Ohio factory or other designated point. Except for “Perishable
Parts” on specific machines, the above warranty applies for a period of two (2) years from the date of original sale to the original purchaser of equipment when recommended operating instructions and maintenance procedures have been followed. These are packed with the machine. Parts warranty is two (2) years, labor is six (6) months.
THIS WARRANTY IS IN LIEU OF ALL OTHER WARRANTIES EXPRESSED OR IMPLIED,
AND OF ALL OTHER OBLIGATIONS OR LIABILITIES ON OUR PART, INCLUDING THE
IMPLIED WARRANTY OF MERCHANTABILITY. THERE ARE NO WARRANTIES WHICH
EXTEND BEYOND THE DESCRIPTION ON THE FACE HEREOF. THIS WARRANTY
DOES NOT APPLY TO THE EQUIPMENT AND SERVICES RELATED TO THE NAYAX
CASHLESS PAYMENT SYSTEM AND GOLD MEDAL EXPRESSLY DISCLAIMS ANY
AND ALL WARRANTIES RELATED TO THE SAME.
In no event shall Gold Medal Products Co. be liable for special, incidental or consequential damages. No claim under this warranty will be honored if the equipment covered has been misused, neglected, damaged in transit, or has been tampered with or changed in any way. No claim under this warranty shall be honored in the event that components in the unit at the time of the claim were not supplied or approved by Gold Medal
Products Co. This warranty is effective only when electrical items have been properly attached to city utility lines only at proper voltages. This warranty is not transferable without the written consent of Gold Medal Products Co.
The term “Original Purchaser” as used in this warranty shall be deemed to mean that person, firm, association, or corporation who was billed by the GOLD MEDAL PRODUCTS CO., or their authorized distributor for the equipment.
THIS WARRANTY HAS NO EFFECT AND IS VOID UNLESS THE ORIGINAL PURCHASER
FIRST CALLS GOLD MEDAL PRODUCTS CO. AT 1-800-543-0862 TO DISCUSS WITH OUR
SERVICE REPRESENTATIVE THE EQUIPMENT PROBLEM, AND, IF NECESSARY, FOR
INSTRUCTIONS CONCERNING THE REPAIR OR REPLACEMENT OF PARTS.
NOTE: This equipment is manufactured and sold for commercial use only.
10700 Medallion Drive, Cincinnati, Ohio 45241-4807 USA gmpopcorn.com
Phone: (800) 543-0862 Fax: (800) 542-1496
(513) 769-7676 (513) 769-8500
© 2023 – The text, descriptions, graphics, layout, and other material in this publication are the exclusive property of
Gold Medal Products Co. and shall not be used, copied, reproduced, or published in any fashion, including website display, without its express written consent. gmpopcorn.com
Page 19
Advertisement
