Ryobi D130VR Specifications

Ryobi D130VR Specifications
OWNER'S OPERATING MANUAL
1/2 in. (13 mm) Electric Drill
Model D130VR Type II
Double Insulated
SPECIFICATIONS:
Chuck Capacity
1/16 in. (1.6 mm) - 1/2 in. (13 mm)
Switch
Adjustable Variable Speed/Reversible
Rating
120 volts, 60 Hz, AC
Input
No Load Speed
Net Weight
5.0 Amperes
0-550 RPM
5.1 lbs. (2.3 kg.)
THANK YOU FOR BUYING A RYOBI DRILL.
Your new drill has been engineered and manufactured to Ryobi's high standard for dependability, ease of operation, and
operator safety. Properly cared for, it will give you years of rugged, trouble-free performance.
CAUTION: Carefully read through this entire owner's manual before using your new drill.
Pay close attention to the Rules for Safe Operation, Warnings, and Cautions. If you use your drill properly and only for what
it is intended, you will enjoy years of safe, reliable service.
Thank you again for buying Ryobi tools.
SAVE THIS MANUAL FOR FUTURE REFERENCE
TABLE OF CONTENTS
1.
2.
3.
4
5.
6.
Product Specifications ................................................................................... 1
Table Of Contents .......................................................................................... 2
Rules For Safe Operation ........................................................................... 2-4
Operation .................................................................................................. 5-10
Maintenance ................................................................................................. 11
Parts Ordering / Service............................................................................... 12
RULES FOR SAFE OPERATION
The purpose of safety symbols is to attract your attention to possible dangers. The safety symbols, and the
explanations with them, deserve your careful attention and understanding. The safety warnings do not by
themselves eliminate any danger. The instructions or warnings they give are not substitutes for proper accident
prevention measures.
SYMBOL
MEANING
SAFETY ALERT SYMBOL:
Indicates caution or warning. May be used in conjunction with other symbols or pictographs.
WARNING: Failure to obey a safety warning can result in serious injury to yourself or to others. Always
follow the safety precautions to reduce the risk of fire, electric shock and personal injury.
CAUTION: Failure to obey a safety warning may result in property damage or personal injury to yourself
or to others. Always follow the safety precautions to reduce the risk of fire, electric shock and personal
injury.
NOTE:
Advises you of information or instructions vital to the operation or maintenance of the equipment.
DOUBLE INSULATION
IMPORTANT
Double insulation is a concept in safety, in electric power
tools, which eliminates the need for the usual three-wire
grounded power cord. All exposed metal parts are isolated
from the internal metal motor components with protecting
insulation. Double insulated tools do not need to be grounded.
Servicing of a tool with double insulation requires extreme
care and knowledge of the system and should be performed
only by a qualified service technician. For service we suggest
you return the tool to your nearest RYOBI FACTORY or
AUTHORIZED SERVICE CENTER for repair. When
servicing use only identical Ryobi replacement parts.
WARNING:
WARNING:
The double insulated system is intended to protect the
user from shock resulting from a break in the tool's
internal wiring. Observe all normal safety precautions
related to avoiding electrical shock.
Page 2
Do not attempt to operate this tool until you have read
thoroughly and understand completely all instructions,
safety rules, etc. contained in this manual. Failure to
comply can result in accidents involving fire, electric
shock, or serious personal injury. Save owner's manual
and review frequently for continuing safe operation, and
instructing others who may use this tool.
RULES FOR SAFE OPERATION
READ ALL INSTRUCTIONS
1. KNOW YOUR POWER TOOL. Read owner's
manual carefully. Learn its applications and
limitations as well as the specific potential
hazards related to this tool.
2. GUARD AGAINST ELECTRICAL SHOCK by
preventing body contact with grounded
surfaces. For example: Pipes, radiators,
ranges, refrigerator enclosures.
3. KEEP GUARDS IN PLACE and in working
order.
4. KEEP WORK AREA CLEAN. Cluttered areas
and benches invite accidents.
5. AVOID DANGEROUS ENVIRONMENT. Don't
use power tool in damp or wet locations or
expose to rain. Keep work area well lit.
6. KEEP CHILDREN AND VISITORS AWAY.
All visitors should wear safety glasses and be
kept a safe distance from work area. Do not
let visitors contact tool or extension cord.
7. STORE IDLE TOOLS. When not in use tools
should be stored in a dry and high or lockedup place - out of the reach of children.
8. DON'T FORCE TOOL. It will do the job better
and safer at the rate for which it was designed.
9. USE RIGHT TOOL. Don't force small tool or
attachment to do the job of a heavy duty tool.
Don't use tool for purpose not intended - for
example - A circular saw should never be
used for cutting tree limbs or logs.
10. WEAR PROPER APPAREL. Do not wear
loose clothing or jewelry that can get caught
in the tool's moving parts and cause personal
injury. Rubber gloves and nonskid footwear
are recommended when working outdoors.
Wear protective hair covering to contain long
hair and keep it from being drawn into nearby
air vents.
11. ALWAYS WEAR SAFETY GLASSES.
Everyday eyeglasses have only impactresistant lenses; they are NOT safety glasses.
12. PROTECT YOUR LUNGS. Wear a face or
dust mask if operation is dusty.
13. PROTECT YOUR HEARING. Wear hearing
protection during extended periods of
operation.
14. DON'T ABUSE CORD. Never carry tool by
cord or yank it to disconnect from receptacle.
Keep cord from heat, oil and sharp edges.
15. SECURE WORK. Use clamps or a vise to
hold work. Both hands are needed to operate
the tool.
16. DON'T OVERREACH. Keep proper footing
and balance at all times. Do not use on a
ladder or unstable support.
17. MAINTAIN TOOLS WITH CARE. Keep tools
sharp at all times, and clean for best and
safest performance. Follow instructions for
lubricating and changing accessories.
18. DISCONNECT TOOLS. When not in use,
before servicing, or when changing
attachments, blades, bits, cutters, etc., all tools
should be disconnected from power supply.
19. REMOVE ADJUSTING KEYS AND
WRENCHES. Form habit of checking to see
that keys and adjusting wrenches are removed
from tool before turning it on.
20. AVOID ACCIDENTAL STARTING. Don't
carry plugged-in tools with finger on switch.
Be sure switch is off when plugging in.
21. MAKE SURE YOUR EXTENSION CORD IS
IN GOOD CONDITION. When using an
extension cord, be sure to use one heavy
enough to carry the current your product will
draw. An undersized cord will cause a drop in
line voltage resulting in loss of power and
overheating. A wire gage size (A.W.G.) of at
least 14 is recommended for an extension
cord 50 feet or less in length. A cord exceeding
100 feet is not recommended. If in doubt, use
the next heavier gage. The smaller the gage
number, the heavier the cord.
22. OUTDOOR USE EXTENSION CORDS.
When tool is used outdoors, use only
extension cords suitable for use outdoors.
Outdoor approved cords are marked with
the suffix W-A, for example - SJTW-A or
SJOW-A.
23. KEEP BITS CLEAN AND SHARP. Sharp bits
minimize stalling and kickback.
Page 3
RULES FOR SAFE OPERATION
24. KEEP HANDS AWAY FROM DRILLING
AREA. Keep hands away from bits. Do not
reach underneath work while bit is rotating. Do
not attempt to remove material while bit is
rotating.
25. NEVER USE IN AN EXPLOSIVE ATMOSPHERE. Normal sparking of the motor could
ignite fumes.
26. INSPECT TOOL CORDS PERIODICALLY
and if damaged, have repaired at your nearest
FACTORY or AUTHORIZED SERVICE
CENTER. Stay constantly aware of cord
location.
27. INSPECT EXTENSION CORDS PERIODICALLY and replace if damaged.
28. KEEP HANDLES DRY, CLEAN, AND FREE
FROM OIL AND GREASE. Always use a
clean cloth when cleaning. Never use brake
fluids, gasoline, petroleum-based products or
any strong solvents to clean your tool.
29. STAY ALERT. Watch what you are doing
and use common sense. Do not operate tool
when you are tired. Do not rush.
30. CHECK DAMAGED PARTS. Before further
use of the tool, a guard or other part that is
damaged should be carefully checked to
determine that it will operate properly and
perform its intended function. Check for
alignment of moving parts, binding of moving
parts, breakage of parts, mounting, and any
other conditions that may affect its operation.
A guard or other part that is damaged should
31.
32.
33.
34.
35.
36.
37.
be properly repaired or replaced by an
authorized service center unless indicated
elsewhere in this instruction manual.
DO NOT USE TOOL IF SWITCH DOES NOT
TURN IT ON AND OFF. Have defective
switches replaced by an authorized service
center.
DRILLING INTO ELECTRICAL WIRING IN
WALLS CAN CAUSE DRILL BIT AND
CHUCK TO BECOME ELECTRICALLY
LIVE. Do not touch the chuck or metal housing
when drilling into a wall; grasp only the
insulated handle(s) provided on the tool.
INSPECT FOR and remove all nails from
lumber before drilling.
DRUGS, ALCOHOL, MEDICATION. Do not
operate tool while under the influence of drugs,
alcohol, or any medication.
WHEN SERVICING USE ONLY IDENTICAL
RYOBI REPLACEMENT PARTS.
POLARIZED PLUGS. To reduce the risk of
electric shock, this tool has a polarized plug
(one blade is wider than the other). This plug
will fit in a polarized outlet only one way. If the
plug does not fit fully in the outlet, reverse the
plug. If it still does not fit, contact a qualified
electrician to install the proper outlet. Do not
change the plug in any way.
SAVE THESE INSTRUCTIONS. Review them
frequently and use them to instruct others
who may use this tool. If you loan someone
this tool, loan them these instructions also.
WARNING:
WEAR YOUR
The operation of any drill can result in foreign objects being thrown into your eyes, which
can result in severe eye damage. Before beginning power tool operation, always wear
safety goggles or safety glasses with side shields and a full face shield when needed. We
recommend Wide Vision Safety Mask for use over eyeglasses or standard safety glasses
FORESIGHT
IS BETTER
with side shields.
THAN NO SIGHT
SAFETY GLASSES
Look for this symbol to point out important safety precautions.
It means attention!!! Your safety is involved.
Page 4
OPERATION
KNOW YOUR ELECTRIC DRILL
APPLICATIONS
See Figure 1.
Before attempting to use your drill, familiarize yourself with
all operating features and safety requirements.
(Use only for the purposes listed below)
1. Drilling in wood.
2. Drilling in ceramics, plastics, fiberglass, and laminates.
3. Drilling in both hard and soft metals.
4. Using driving accessories, such as driving screws with
screwdriver bits.
WARNING:
If any parts are missing do not operate your drill until the
missing parts are replaced. Failure to do so could result
in possible serious injury.
5. Mixing paints.
CHUCK
AUXILIARY
HANDLE
SWITCH
TRIGGER
VARIABLE SPEED
CONTROL SELECTOR
LOCK-ON
BUTTON
KEY STRAP
CHUCK KEY
Fig. 1
ELECTRICAL CONNECTION
WARNING:
Do not allow familiarity with your drill to make you careless. Remember that a careless fraction of second is
sufficient to inflict severe injury.
Your drill has a precision built electric motor. It should be
connected to a power supply that is 120 volts, 60 Hz only
(normal household current). Do not operate this tool on
direct current (DC). A substantial voltage drop will cause a
loss of power and the motor will overheat. If your tool does
not operate when plugged into an outlet, double-check the
power supply.
Page 5
OPERATION
SWITCH
LOCK-ON
BUTTON
See Figure 2.
To turn your drill ON, depress the switch trigger. Release
switch trigger to turn your drill OFF.
LOCK-ON BUTTON
See Figure 2.
Your drill is equipped with a "lock-on" feature, which is
convenient when continuous drilling for extended periods of
time is required. To lock-on, depress the switch trigger, push
in and hold the lock-on button located on the side of the
handle, then release switch trigger. Release lock-on button
and your drill will continue running.
To release the lock, depress the switch trigger and release.
If you have the "lock-on" feature engaged during use and
your drill becomes disconnected from power supply, disengage the "lock-on" feature immediately.
SWITCH TRIGGER
WARNING:
FORWARD/REVERSE LEVER
Fig. 2
FORWARD
Before connecting your drill to power supply source,
always check to be sure it is not in “lock-on” position
(depress and release switch trigger). Failure to do so
could result in accidental starting of your drill resulting in
possible serious injury. Also, do not lock the trigger on
jobs where your drill may need to be stopped suddenly.
REVERSIBLE
See Figure 3.
Your drill has the feature of being reversible. The direction of
chuck rotation is controlled by a lever located above the
switch trigger. With your drill held in normal operating
position, the direction of rotation lever should be positioned
to the left of the switch for drilling operation. The direction of
rotation is reversed when the lever is to the right of the
switch.
The design of the switch will not permit changing the
direction of rotation while the drill is running. Release
the switch trigger and allow the drill to stop before
changing its direction.
NOTE: Your drill will not run unless switch lever is
pushed fully to the left or right.
REVERSE
Fig. 3
POWER
CORD
CHUCK KEY
See Figure 4.
A chuck key has been provided for use when installing or
removing bits. It is also used when removing the chuck. (See
chuck removal section).
CHUCK KEY STORAGE
See Figure 4.
For storage when not in use, the chuck key has been
attached to the power cord. A key strap has been used. One
end of the key strap is attached to the chuck key, while the
other end is attached to the power cord.
Page 6
KEY
STRAP
CHUCK KEY
Fig. 4
OPERATION
VARIABLE SPEED
See Figure 5.
Your drill has a variable speed control selector designed to
allow operator control and adjustment of speed and torque
limits. The speed and torque of your drill can be increased or
decreased by rotating the variable speed control selector in
the direction of the arrows shown in figure 5.
NOTE: Hold your drill in normal operating position and turn
the variable speed control selector clockwise to increase the
speed and torque of your drill. Turn counterclockwise to
decrease the speed and torque of your drill.
If you desire to lock the switch on at a given speed, depress
the switch trigger, push in and hold the lock-on button, and
release the switch trigger. Next, adjust the variable speed
control selector until the desired speed is reached.
NOTE: If the variable speed control selector is fully
turned in the counterclockwise direction (zero setting)
your drill may not run.
If you desire not to use the variable speed control
selector, turn it in the full clockwise direction. This will
allow the speed of your drill to be fully controlled by the
amount of switch trigger depression.
Avoid running your drill at low speeds for extended periods of
time. Running at low speeds under constant usage may
cause your drill to become overheated. If this occurs, cool
your drill by running it without a load and at full speed.
The following guidelines may be used in determining correct
speed for various applications:
LOW speed is ideal when minimum speed and power is
required. For example: starting holes without center punching, driving screws, mixing paint, and drilling in ceramics.
MEDIUM speed is suitable for drilling hard metals, plastics,
and laminates.
HIGH speed produces best results when maximum power is
required. For example: drilling in wood; soft metals such as
aluminum, brass, and copper; and when using driving accessories.
VARIABLE SPEED
CONTROL SELECTOR
TO
DECREASE
SPEED
TO
INCREASE
SPEED
Fig. 5
AUXILIARY
HANDLE
WING
SCREW
AUXILIARY HANDLE
See Figure 6.
An auxiliary handle is installed on your drill for ease of
operation and to help prevent loss of control. It can be rotated
360° to any angle.
TO ROTATE:
1. Loosen wing screw.
2. Rotate auxiliary handle to desired angle.
3. Tighten wing screw securely.
To prevent possible loss of control, auxiliary handle should
be checked periodically for tightness. DO NOT operate drill
with handle loose.
SPACER
Fig. 6
Page 7
OPERATION
WARNING:
DRILL BIT
Your drill should never be connected to power supply
when you are assembling parts, making adjustments,
installing or removing drill bits, or when not in use.
Disconnecting your drill will prevent accidental starting
that could cause serious injury.
TO INSTALL BITS
CHUCK JAWS
See Figure 7.
1. UNPLUG YOUR DRILL.
WARNING:
Failure to unplug your drill could result in accidental
starting causing serious injury.
RIGHT
Fig. 7
WRONG
Fig. 8
2. Open or close the chuck jaws to a point where the
opening is slightly larger than the drill bit you intend to
use. Also, raise the front of your drill slightly to keep the
drill bits from falling out of the chuck jaws.
3. Insert drill bit into chuck the full length of the jaws.
WARNING:
Do not insert drill bit into chuck jaws and tighten as shown in
figure 8. This could cause drill bit to be thrown from your drill
resulting in possible serious personal injury or damage to
your chuck.
4. Tighten the chuck jaws securely on drill bit, using only
the chuck key provided. Place chuck key in each of the
three holes, and tighten in a clockwise direction. Do not
use a wrench to tighten or loosen the chuck jaws.
5. Remove the chuck key.
TO REMOVE BITS
1. UNPLUG YOUR DRILL.
WARNING:
Failure to unplug your drill could result in accidental
starting causing serious injury.
2. Loosen the chuck jaws using only the chuck key provided. Do not use a wrench to tighten or loosen the
chuck jaws.
3. Remove drill bit from chuck jaws.
4. Remove the chuck key.
Page 8
OPERATION
WARNING:
Always wear safety goggles or safety glasses with side
shields when operating drill. Failure to do so could result
in dust, shavings, or loose particles being thrown into your
eyes, resulting in possible serious injury.
DRILLING
See Figure 9.
1.
Depress and release the switch trigger to be sure your
drill is in OFF position before connecting it to power
supply.
2.
Check the direction of rotation lever for correct setting
(forward or reverse). See Figure 3, Page 6.
3.
Secure the material to be drilled in a vise or with
clamps to keep it from turning as the drill bit rotates.
4.
Plug your drill into power supply source.
5.
Hold your drill firmly and place the bit at the point to be
drilled.
6.
Depress the switch trigger to start your drill. Do not
lock the switch ON for jobs where your drill may need
to be stopped suddenly.
7.
Move the drill bit into the workpiece applying only
enough pressure to keep the bit cutting. Do not force
your drill or apply side pressure to elongate a hole. Let
your drill and bit do the work. See Figure 9.
Fig. 9
WARNING:
WARNING:
Drilling into electrical wiring in walls can cause drill bit
and chuck to become electrically live. DO NOT touch
any part of the chuck or metal housing when drilling into
a wall. Grasp only the insulated handles provided on
the tool. Failure to heed this warning can result in
serious personal injury.
Be prepared for binding or breakthrough. When these
situations occur, drill has a tendency to grab and kick in
the opposite direction and could cause loss of control
when breaking through material. If not prepared, this loss
of control can result in possible serious injury.
When drilling hard, smooth surfaces use a center punch to
mark the desired hole location. This will prevent the drill bit
from slipping off center as the hole is started. However, the
variable speed feature allows starting holes without center
punching if desired. To accomplish this, operate your drill at
a low speed until the hole is started.
When drilling metals use a light oil on the drill bit to keep it
from overheating. The oil will prolong the life of the bit and
increase the drilling action.
If the bit jams in the workpiece or if your drill stalls, stop the
tool immediately. Remove the bit from the workpiece and
determine the reason for jamming.
Page 9
WARNING:
To prevent the risk of serious injury, make sure the
auxiliary handle position is adjusted for maximum control.
If the drill binds, the entire drill motor will rotate and
could hit the operator resulting in serious injury. Confirm
the position of the auxiliary handle by locating the drill in
the planned operating position before connecting to
power supply.
OPERATION
CHUCK REMOVAL
See Figures 10, 11, and 12.
Whenever necessary to remove the chuck for replacement,
etc., use the following procedure for chuck removal:
MALLET
CHUCK
1. UNPLUG YOUR DRILL.
WARNING:
Failure to unplug your drill could result in accidental
starting causing serious injury.
2. Open chuck jaws. Insert a 5/16 inch or larger hex key
wrench (allen wrench) into the chuck of your drill and
tighten the chuck jaws securely.
3. Tap the hex key wrench sharply with a mallet in a
clockwise direction. See Figure 10. This will loosen the
chuck screw for removal.
4. Open the chuck jaws and remove hex key wrench.
Remove the chuck screw by turning it in a clockwise
direction. See Figure 11.
NOTE: The chuck screw has left hand threads.
5. Insert hex key wrench in chuck and tighten chuck jaws
securely. Tap sharply with a mallet in a counterclockwise direction. This will loosen the chuck on the spindle.
It can now be unscrewed by hand. See Figure 12.
CHUCK
JAWS
HEX KEY WRENCH
(ALLEN WRENCH)
CHUCK TIGHTENING
Fig. 10
TO RETIGHTEN A LOOSE CHUCK
The chuck may at times become loose on the spindle and
develop a wobble. Also, the chuck screw may become loose
causing the chuck jaws to bind and prevent them from
closing. To tighten, follow these steps:
Fig. 11
1. UNPLUG YOUR DRILL.
WARNING:
Failure to unplug your drill could result in accidental
starting causing serious injury.
2. Insert hex key wrench into chuck and tighten chuck
jaws securely. Tap allen wrench sharply with a mallet in
a clockwise direction. This will tighten the chuck on the
spindle. See Figure 10.
3. Open the chuck jaws and remove hex key wrench.
4. Tighten the chuck screw.
NOTE: The chuck screw has left hand threads.
CHUCK REMOVAL
Page 10
Fig. 12
MAINTENANCE
WARNING:
When servicing use only identical Ryobi replacement
parts. Use of any other parts may create a hazard or
cause product damage.
GENERAL
Avoid using solvents when cleaning plastic parts. Most
plastics are susceptible to damage from various types of
commercial solvents and may be damaged by their use. Use
clean cloths to remove dirt, carbon dust, etc.
When electric tools are used on fiberglass boats, sports
cars, wallboard, spackling compounds, or plaster, it has
been found that they are subject to accelerated wear and
possible premature failure, as the fiberglass chips and
grindings are highly abrasive to bearings, brushes,
commutators, etc. Consequently it is not recommended
that this tool be used for extended work on any fiberglass
material, wallboard, spackling compounds, or plaster. During
any use on fiberglass it is extremely important that the tool
is cleaned frequently by blowing with an air jet.
WARNING:
Always wear safety goggles or safety glasses with side
shields during power tool operation or when blowing dust.
If operation is dusty, also wear a dust mask.
WARNING:
Do not at any time let brake fluids, gasoline, petroleumbased products, penetrating oils, etc. come in contact
with plastic parts. They contain chemicals that can
damage, weaken, or destroy plastic.
EXTENSION CORDS
The use of any extension cord will cause some loss of power.
To keep the loss to a minimum and to prevent tool from
overheating, use an extension cord that is heavy enough to
carry the current the tool will draw.
A wire gage size (A.W.G.) of at least 14 is recommended for
an extension cord 50 feet or less in length. When working
outdoors, use an extension cord that is suitable for outdoor
use. The cord's jacket will be marked WA.
WARNING:
Check extension cords before each use. If damaged
replace immediately. Never use tool with a damaged cord
since touching the damaged area could cause electrical
shock resulting in serious injury.
WARNING:
CAUTION:
Keep extension cords away from the drilling area and
position the cord so that it will not get caught on lumber,
tools, etc., during drilling operation.
Do not use this product as a component of other products.
Also, do not use attachments or accessories not
recommended for use with this product. Any such use
could result in possible serious personal injury.
LUBRICATION
All of the bearings in this tool are lubricated with a sufficient
amount of high grade lubricant for the life of the unit under
normal operating conditions. Therefore, no further lubrication
is required.
Page 11
OWNER'S OPERATING MANUAL
1/2 in. (13 mm) Electric Drill
Model D130VR Type II
Double Insulated
EXTENSION CORD CAUTION
When using a power tool at a considerable distance from a power
source, be sure to use an extension cord that has the capacity to
handle the current the tool will draw. An undersized cord will
cause a drop in line voltage, resulting in overheating and loss of
power. Use the chart to determine the minimum wire size required in an extension cord. Only round jacketed cords should be
used.
When working with a tool outdoors, use an extension cord that is
designed for outside use. This is indicated by the letters "WA" on
the cord's jacket.
Before using any extension cord, inspect it for loose or exposed
wires and cut or worn insulation.
**Ampere rating
(on tool data plate)
0-2.0
Cord Length
2.1-3.4
3.5-5.0
5.1-7.0
7.1-12.0 12.1-16.0
Wire Size (A.W.G.)
25'
16
16
16
16
14
14
50'
16
16
16
14
14
12
100'
16
16
14
12
10
—
CAUTION:
Keep the extension cord clear of the working area. Position the
cord so that it will not get caught on workpiece, tools, or other
obstructions while you are working with a power tool.
**Used on 12 gauge - 20 amp circuit.
• SERVICE
Now that you have purchased your tool, should a need ever exist for repair parts or service,
simply contact your nearest Ryobi Factory Service Center. Be sure to provide all pertinent
facts when you call or visit. Please refer to the Service Center insert or call 1-800-525-2579
in the United States or 1-800-265-6778 in Canada for your nearest Factory or Authorized
Service Center.
• MODEL NO. AND SERIAL NO.
The model number of this tool will be found on a plate attached to the motor housing.
Please record the model number and serial number in the space provided below.
•
MODEL NUMBER
•
SERIAL NUMBER
D130VR Type II
RYOBI AMERICA CORP.
5201 Pearman Dairy Road
Anderson, SC 29625-8950
Post Office Box 1207
Anderson, SC 29622-1207
Phone 1-800-525-2579
972000-398
RYOBI CANADA INC.
Post Office Box 910
Cambridge, Ontario N1R 6K2
Phone 1-800-265-6778
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertisement