Continuous Ink System for EPSON Artisan 800/700/600

Continuous Ink System for EPSON Artisan 800/700/600
EPSON Artisan 800/700/600 Printer
This Version of the Continuous Ink Flow System comes with Prefilled
Cartridges and Auto Reset Chips. You just need to fill the Reservoir
bottles and print! The whole operation is very easy. It’s really an
effective tool to save your money.
CIS for Epson Artisan
800/700/600 Instruction
Thank you for purchasing ST Continuous Ink Supply System. We appreciate your support and will try
our best to make your experience with our products a pleasant one. Printing has been a different
experience ever since you installed ST Continuous Ink Supply system on your own printer. Just
imagining being able to print without regard to the ink level in those expensive little cartridges.
Please take your time installing ST Continuous Ink Supply system. Do not remove your old cartridge
until you have the ST CIS system primed and ready to install (to prevent the drying of heads). In
addition, make sure you are getting perfect nozzle checks before installing the ST CIS system. The ST
CIS system won’t be able to work properly if the nozzles are previously clogged.
Most people get a perfect nozzle check the first time after installing the ST Continuous Ink Supply
system; others may need to run two or three cleaning cycles or let the printer sit for a while before they
get the perfect results.
1. General Guide:
1) Components
A. CIS system
1 set
B. Air filters
6 pcs
C. Short tube clip
1 set (2 pcs)
D. Printhead part
1 pc
E. Position-limit part
1 pc
F. Instruction CD
1 pc
2) Opening box inspection
a、Check whether all the accessories are ready.
b、Check whether there's the leakage of the CISS, whether some tubes have been separated from the CISS,
whether there are air bubbles in the tube (If there exists more than 20CM air space, please kindly to contact with the
local dealer)
2. Printer testing:
1) Check whether the printer is in normal condition, like mechanical status, lubrication status etc.
2) Print testing lines to ensure the printing head is good condition.
3) Print pictures to see whether the printing image is ok.
3. Installation Procedures:
Step 1: Preparation
Put the CISS on the left side of the printer.
and place all the tubes at correct position.
Pull out the small rubber plug from the
air hole as picture shown above.
Place 6pcs of air filters into air holes
Step 2: Take out the original cartridges
Open the printer cover
take out the original cartridges
all cartridges move out
Step 3: Install Cartridges
Place CIS cartridges into the carriage
Press those cartridges to make sure it
is well installed.
Place the black position-limit part as above
picture shown
Position-limit part well installed
Stick the tube clip on the printer as above picture shown
Clip the tube line on the tubing holder
Step 4: Install printhead part
Close the printer cover
Plug in
Switch on
After 6 seconds, open the printer cover see the carriage move status, when the carriage move to left side, please draw out the power
Install the printhead part to the position as above picture shown. You will hear a sound “da” when it is well installed.
Step 5.
Connect the power cord.
Close the cover
Turn on the power and check whether the
printer can work.
Step 6: Check the nozzle
Nozzle is OK
Print test lines. If it is OK, then you can begin using.
Broken Lines
If there is broken lines, then pls clean the printer head.
Enter Checking Nozzle Panel
Broken lines may be caused by air entering the nozzles. If there is still some broken lines after cleaning printer head repeatedly,
especially for single color, then you can leave the printer for about 1 hour. Then the broken lines may disappear. If there is still
such problem, then pls contact local dealer.
4. Chip Reset
If the printer display or computer panel reminding you to change cartridges, please open the printer cover, press the reset button more
than 3 seconds, then it can be reset.
5、Refill Ink
Please pay attention to the ink level in the reservoirs; if the ink level is below 1CM as the picture shown above, please use refill kits to fill
ink into Reservoir bottles. Carefully pull out the rubber plugs from the ink refill holes (There is possibility of ink spattering. Pls be careful.)
Refill ink according to the colors. Then re-cap the rubber. (Please keep the printer and the reservoir bottles at the same horizontal line
during the process of refilling ink.)
6. Attention for Maintenance:
Take out the CISS including the inner cartridges and other components. Then remove support arm from printer, and
re-install original cartridges. Please inquire local dealer before sending to maintenance.
7. Notice:
1. Please don’t take out cartridge at random after installing the CIS system. Keep the reservoir bottles on the same
level with the printer.
2. Try to keep at least 1/2 inch of ink in the bottles.
3. Don’t place the Reservoir Bottles too much higher or lower than the printer.
4. Suggested using in a dry place between 15 and 35 degree. Avoid exposure to direct sunlight.
5. Don’t reverse or lean the continuous ink supply systems during shipping. Please make sure all the ink filling holes
and ventilation holes are closed tightly during transportation. Otherwise, the ink may leak.
6. Don’t sway the cartridge frequently. It may cause ink leakage.
7. Don’t pull out the connector of cartridge and don’t tear off adhesive tape at the bottom of cartridge.
8. Warning:
1. Not drinkable; keep it out reach of children.
2. Avoid exposure to direct sunshine and don’t keep it in high or freezing temperature.
3. Avoid collision and fallen down.
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF