TOSHIBA 2000 Portable Personal Computer User`s Manual

TOSHIBA 2000 Portable Personal Computer User`s Manual
TOSHIBA 2000
Portable Personal Computer
User’s Manual
Copyright
© 2002 by TOSHIBA Corporation. All rights reserved. Under the copyright laws,
this manual cannot be reproduced in any form without the prior written permission
of TOSHIBA. No patent liability is assumed, with respect to the use of the information contained herein.
TOSHIBA 2000 Portable Personal Computer User’s Manual
First edition January 2002
Disclaimer
This manual has been validated and reviewed for accuracy. The instructions and
descriptions it contains are accurate for the TOSHIBA 2000 Portable Personal
Computer at the time of this manual’s production. However, succeeding computers
and manuals are subject to change without notice. TOSHIBA assumes no liability
for damages incurred directly or indirectly from errors, omissions or discrepancies
between the computer and the manual.
Trademarks
Intel and Pentium are registered trademarks and SpeedStep is a trademark of Intel
Corporation.
Windows and Microsoft are registered trademarks of Microsoft Corporation.
Photo CD is a trademark of Eastman Kodak.
Other trademarks and registered trademarks not listed above may be used in this
manual.
FCC information
Product Name : Portégé 2000
Model number : PP200
FCC notice "Declaration of Conformity
Information"
This equipment has been tested and found to comply with the limits for a Class B
digital device, pursuant to part 15 of the FCC rules. These limits are designed to
provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if
not installed and used in accordance with the instructions, may cause harmful
interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful
interference to radio or television reception, which can be determined by turning the
equipment off and on, the user is encouraged to try to correct the interference by
one or more of the following measures:
◆
Reorient or relocate the receiving antenna.
◆
Increase the separation between the equipment and receiver.
◆
Connect the equipment into an outlet on a circuit different from that to which
the receiver is connected.
◆
Consult the dealer or an experienced radio/TV technician for help.
WARNING: Only peripherals complying with the FCC class B limits may
be attached to this equipment. Operation with non-compliant peripherals or peripherals not recommended by TOSHIBA is likely to result in
interference to radio and TV reception. Shielded cables must be used
between the external devices and the computer’s external monitor port,
USB port and microphone jack. Changes or modifications made to this
equipment, not expressly approved by TOSHIBA or parties authorized by
TOSHIBA could void the user’s authority to operate the equipment. The
modular cable that comes with the computer must be used to connect a
modem. Connect the end of the modular cable with the core to the
computer.
FCC conditions
This device complies with part 15 of the FCC Rules. Operation is subject to the
following two conditions:
1. This device may not cause harmful interference.
2. This device must accept any interference received, including interference that
may cause undesired operation.
Contact
Address:
TOSHIBA America Information Systems, Inc.
9740 Irvine Boulevard
Irvine, California 92618-1697
Telephone:
(949)583-3000
EU Declaration of Conformity
TOSHIBA declares, that the product: PP200* conforms to the following Standards:
Supplementary Information:
“The product complies with the requirements
of the Low Voltage Directive 73/23/EEC, the
EMC Directive 89/336/EEC and/or the R&TTE
Directive 1999/05/EEC.”
This product is carrying the CE-Mark in accordance with the related European
Directives. Responsible for CE-Marking is TOSHIBA Europe, Hammfelddamm 8,
41460 Neuss, Germany.
VCCI Class B Information
Modem warning notice
Conformity Statement
The equipment has been approved to [Commission Decision “CTR21”] for panEuropean single terminal connection to the Public Switched Telephone Network
(PSTN).
However, due to differences between the individual PSTNs provided in different
countries/regions the approval does not, of itself, give an unconditional assurance
of successful operation on every PSTN network termination point.
In the event of problems, you should contact your equipment supplier in the first
instance.
Network Compatibility Statement
This product is designed to work with, and is compatible with the following
networks. It has been tested to and found to conform with the additional requirements conditional in EG 201 121.
Germany
ATAAB AN005,AN006,AN007,AN009,AN010 and
DE03,04,05,08,09,12,14,17
Greece
ATAAB AN005,AN006 and GR01,02,03,04
Portugal
ATAAB AN001,005,006,007,011 and P03,04,08,10
Spain
ATAAB AN005,007,012, and ES01
Switzerland
ATAAB AN002
All other countries/regions ATAAB AN003,004
Specific switch settings or software setup are required for each network, please refer
to the relevant sections of the user guide for more details.
The hookflash (timed break register recall) function is subject to separate national
type approvals. It has not been tested for conformity to national type regulations,
and no guarantee of successful operation of that specific function on specific
national networks can be given.
Japan regulations
Region selection
If you are using the computer in Japan, technical regulations described in the
Telecommunications Business Law require that you select the Japan region mode. It
is illegal to use the modem in Japan with any other selection.
Redial
Up to two redial attempts can be made. If more than two redial attempts are made,
the modem will return Black Listed. If you are experiencing problems with the
Black Listed code, set the interval between redials at one minute or longer.
Japan’s Telecommunications Business Law permits up to two redials on analogue
telephones, but the redials must be made within a total of three minutes.
The internal modem is approved by Japan Approvals Institute for Telecommunications Equipment.
A00-0940JP
Pursuant to FCC CFR 47, Part 68:
When you are ready to install or use the modem, call your local telephone company
and give them the following information:
◆
The telephone number of the line to which you will connect the modem
◆
The registration number that is located on the device
The FCC registration number of the modem will be found on either the device which
is to be installed, or, if already installed, on the bottom of the computer outside of
the main system label.
◆
The Ringer Equivalence Number (REN) of the modem, which can vary. For the
REN of your modem, refer to your modem’s label.
The modem connects to the telephone line by means of a standard jack called the
USOC RJ11C.
Type of service
Your modem is designed to be used on standard-device telephone lines. Connection to telephone company-provided coin service (central office implemented
systems) is prohibited. Connection to party lines service is subject to state tariffs. If
you have any questions about your telephone line, such as how many pieces of
equipment you can connect to it, the telephone company will provide this information upon request.
Telephone company procedures
The goal of the telephone company is to provide you with the best service it can. In
order to do this, it may occasionally be necessary for them to make changes in their
equipment, operations, or procedures. If these changes might affect your service or
the operation of your equipment, the telephone company will give you notice in
writing to allow you to make any changes necessary to maintain uninterrupted
service.
If problems arise
If any of your telephone equipment is not operating properly, you should immediately remove it from your telephone line, as it may cause harm to the telephone
network. If the telephone company notes a problem, they may temporarily discontinue service. When practical, they will notify you in advance of this disconnection.
If advance notice is not feasible, you will be notified as soon as possible. When
you are notified, you will be given the opportunity to correct the problem and
informed of your right to file a complaint with the FCC. In the event repairs are ever
needed on your modem, they should be performed by TOSHIBA Corporation or an
authorized representative of TOSHIBA Corporation.
Disconnection
If you should ever decide to permanently disconnect your modem from its present
line, please call the telephone company and let them know of this change.
Fax branding
The Telephone Consumer Protection Act of 1991 makes it unlawful for any person
to use a computer or other electronic device to send any message via a telephone
fax machine unless such message clearly contains in a margin at the top or bottom
of each transmitted page or on the first page of the transmission, the date and time it
is sent and an identification of the business, other entity or individual sending the
message and the telephone number of the sending machine or such business, other
entity or individual. In order to program this information into your fax modem, you
should complete the setup of your fax software before sending messages.
Instructions for IC CS-03 certified equipment
1 The Industry Canada label identifies certified equipment. This certification
means that the equipment meets certain telecommunications network protective,
operational and safety requirements as prescribed in the appropriate Terminal
Equipment Technical Requirements document(s). The Department does not
guarantee the equipment will operate to the user’s satisfaction.
Before installing this equipment, users should ensure that it is permissible to be
connected to the facilities of the local telecommunications company. The
equipment must also be installed using an acceptable method of connection.
The customer should be aware that compliance with the above conditions may
not prevent degradation of service in some situations. Repairs to certified
equipment should be coordinated by a representative designated by the
supplier. Any repairs or alterations made by the user to this equipment, or
equipment malfunctions, may give the telecommunications company cause to
request the user to disconnect the equipment.
Users should ensure for their own protection that the electrical ground connections of the power utility, telephone lines and internal metallic water pipe system,
if present, are connected together. This precaution may be particularly important
in rural areas.
CAUTION: Users should not attempt to make such connections themselves, but should contact the appropriate electric inspection authority,
or electrician, as appropriate.
2 The user manual of analog equipment must contain the equipment’s Ringer
Equivalence Number (REN) and an explanation notice similar to the following:
The Ringer Equivalence Number (REN) of the modem, which can vary. For the
REN of your modem, refer to your modem’s label.
NOTICE: The Ringer Equivalence Number (REN) assigned to each
terminal device provides an indication of the maximum number of
terminals allowed to be connected to a telephone interface. The termination on an interface may consist of any combination of devices subject
only to the requirement that the sum of the Ringer Equivalence Numbers
of all the devices does not exceed 5.
3 The standard connecting arrangement (telephone jack type) for this equipment is
jack type(s): USOC RJ11C.
The IC registration number of the modem is shown below.
Canada: 1353 11026A
Notes for Users in Australia and New Zealand
Modem warning notice for Australia
Modems connected to the Australian telecoms network must have a valid Austel
permit. This modem has been designed to specifically configure to ensure compliance with Austel standards when the country/region selection is set to Australia.
The use of other country/region setting while the modem is attached to the
Australian PSTN would result in you modem being operated in a non-compliant
manner. To verify that the country/region is correctly set, enter the command ATI
which displays the currently active setting.
To set the country/region permanently to Australia, enter the following command
sequence:
AT%TE=1
ATS133=1
AT&F
AT&W
AT%TE=0
ATZ
Failure to set the modem to the Australia country/region setting as shown above
will result in the modem being operated in a non-compliant manner. Consequently,
there would be no permit in force for this equipment and the Telecoms Act 1991
prescribes a penalty of $12,000 for the connection of non-permitted equipment.
Notes for use of this device in New Zealand
◆
The grant of a Telepermit for a device in no way indicates Telecom acceptance
of responsibility for the correct operation of that device under all operating
conditions. In particular the higher speeds at which this modem is capable of
operating depend on a specific network implementation which is only one of
many ways of delivering high quality voice telephony to customers. Failure to
operate should not be reported as a fault to Telecom.
◆
In addition to satisfactory line conditions a modem can only work properly if:
a/
it is compatible with the modem at the other end of the call and
b/
the application using the modem is compatible with the application at the
other end of the call - e.g., accessing the Internet requires suitable
software in addition to a modem.
◆
This equipment shall not be used in any manner which could constitute a
nuisance to other Telecom customers.
◆
Some parameters required for compliance with Telecom’s PTC Specifications
are dependent on the equipment (PC) associated with this modem. The
associated equipment shall be set to operate within the following limits for
compliance with Telecom Specifications:
a/
There shall be no more than 10 call attempts to the same number within
any 30 minute period for any single manual call initiation, and
b/
The equipment shall go on-hook for a period of not less than 30 seconds
between the end of one attempt and the beginning of the next.
c/
Automatic calls to different numbers shall be not less than 5 seconds
apart.
◆
Immediately disconnect this equipment should it become physically damaged,
and arrange for its disposal or repair.
◆
The correct settings for use with this modem in New Zealand are as follows:
ATB0 (CCITT operation)
AT&G2 (1800 Hz guard tone)
AT&P1 (Decadic dialing make-break ratio =33%/67%)
ATS0=0 (not auto answer)
ATS10=less than 150 (loss of carrier to hangup delay, factory default of 15
recommended)
ATS11=90 (DTMF dialing on/off duration=90 ms)
ATX2 (Dial tone detect, but not (U.S.A.) call progress detect)
◆
When used in the Auto Answer mode, the S0 register must be set with a value
of 3 or 4. This ensures:
(a) a person calling your modem will hear a short burst of ringing before the
modem answers. This confirms that the call has been successfully
switched through the network.
(b) caller identification information (which occurs between the first and
second ring cadences) is not destroyed.
◆
The preferred method of dialing is to use DTMF tones (ATDT...) as this is
faster and more reliable than pulse (decadic) dialing. If for some reason you
must use decadic dialing, your communications program must be set up to
record numbers using the following translation table as this modem does not
implement the New Zealand “Reverse Dialing” standard.
Number to be dialed: 0 1 2 3 4 5 6 7 8 9
Number to program into computer: 0 9 8 7 6 5 4 3 2 1
Note that where DTMF dialing is used, the numbers should be entered
normally.
◆
The transmit level from this device is set at a fixed level and because of this
there may be circumstances where the performance is less than optimal. Before
reporting such occurrences as faults, please check the line with a standard
Telepermitted telephone, and only report a fault if the phone performance is
impaired.
◆
It is recommended that this equipment be disconnected from the Telecom line
during electrical storms.
◆
When relocating the equipment, always disconnect the Telecom line connection before the power connection, and reconnect the power first.
◆
This equipment may not be compatible with Telecom Distinctive Alert cadences and services such as FaxAbility.
NOTETHATFAULTCALLOUTSCAUSEDBYANYOFTHEABOVE
CAUSESMAYINCURACHARGEFROMTELECOM
General conditions
As required by PTC 100, please ensure that this office is advised of any changes to
the specifications of these products which might affect compliance with the relevant
PTC Specifications.
The grant of this Telepermit is specific to the above products with the marketing
description as stated on the Telepermit label artwork. The Telepermit may not be
assigned to other parties or other products without Telecom approval.
A Telepermit artwork for each device is included from which you may prepare any
number of Telepermit labels subject to the general instructions on format, size and
colour on the attached sheet.
The Telepermit label must be displayed on the product at all times as proof to
purchasers and service personnel that the product is able to be legitimately
connected to the Telecom network.
The Telepermit label may also be shown on the packaging of the product and in the
sales literature, as required in PTC 100.
The charge for a Telepermit assessment is $337.50. An additional charge of $337.50
is payable where an assessment is based on reports against non-Telecom New
Zealand Specifications. $112.50 is charged for each variation when submitted at the
same time as the original.
An invoice for $NZ1237.50 will be sent under separate cover.
Table of Contents
Preface
Manual contents ............................................................................... xix
Conventions ........................................................................................ xx
Abbreviations ....................................................................................... xx
Icons ................................................................................................... xx
Keys ................................................................................................... xx
Key operation ..................................................................................... xxi
Display ............................................................................................... xxi
Messages .......................................................................................... xxi
General Precautions
Stress injury .................................................................................... xxiii
Heat injury ....................................................................................... xxiii
Pressure or impact damage .......................................................... xxiii
PC card overheating ...................................................................... xxiii
Chapter 1 Introduction
Equipment checklist .......................................................................... 1-1
Features ............................................................................................. 1-3
Special features ................................................................................. 1-6
Utilities ................................................................................................ 1-8
Options ............................................................................................. 1-10
Chapter 2 The Grand Tour
Front with the display closed ........................................................... 2-1
Left side .............................................................................................. 2-2
Right side ........................................................................................... 2-3
Back side ............................................................................................ 2-4
Underside ........................................................................................... 2-5
Front with the display open .............................................................. 2-6
Indicators ............................................................................................ 2-8
AC adaptor ....................................................................................... 2-10
xiii
Chapter 3 Getting Started
Setting up your work space ............................................................... 3-2
General conditions .............................................................................. 3-2
Placement of computer ....................................................................... 3-2
Seating and posture ............................................................................ 3-3
Lighting ............................................................................................... 3-4
Work habits ........................................................................................ 3-4
Opening the display ........................................................................... 3-5
Connecting the AC adaptor ............................................................... 3-5
Turning on the power ........................................................................ 3-7
Windows XP Professional/2000 setup ............................................... 3-8
Turning off the power ........................................................................ 3-8
Shut Down mode (Boot mode) ............................................................ 3-8
Hibernation mode ................................................................................ 3-9
Standby mode .................................................................................. 3-11
Restarting the computer .................................................................. 3-13
Restoring the Windows system ....................................................... 3-13
Chapter 4 Operating Basics
Using the Touch Pad .......................................................................... 4-1
Using the USB FDD Kit ....................................................................... 4-2
Connecting 3 1/2" diskette drive .......................................................... 4-3
Disconnecting 3 1/2" diskette drive ..................................................... 4-4
Diskette care ...................................................................................... 4-4
Wireless communications .................................................................. 4-5
Wireless LAN ...................................................................................... 4-5
Wireless communication switch .......................................................... 4-5
Wireless communication LED ............................................................. 4-5
LAN ...................................................................................................... 4-6
LAN cable types ................................................................................. 4-6
Connecting cable ................................................................................ 4-6
Disconnecting cable ............................................................................ 4-7
Network Device Switch ........................................................................ 4-8
Super Long Life scheme ................................................................... 4-10
Using the internal modem ............................................................... 4-10
Region selection ............................................................................... 4-10
Properties menu ................................................................................ 4-11
Connecting ........................................................................................ 4-13
Disconnecting ................................................................................... 4-14
xiv
Cleaning the computer .................................................................... 4-14
Moving the computer ....................................................................... 4-14
Heat dispersal ................................................................................... 4-15
Chapter 5 The Keyboard
Typewriter keys .................................................................................. 5-1
F1 … F12 function keys ...................................................................... 5-2
Soft keys: Fn key combinations ......................................................... 5-2
Emulating keys on enhanced keyboard ............................................... 5-2
Hotkeys .............................................................................................. 5-4
Fn Sticky key ..................................................................................... 5-6
Windows special keys ........................................................................ 5-7
Keypad overlay ................................................................................... 5-7
Turning on the overlays ....................................................................... 5-7
Temporarily using normal keyboard (overlay on) .................................. 5-8
Temporarily using overlay (overlay off) ................................................. 5-9
Temporarily changing modes ............................................................... 5-9
Generating ASCII characters ............................................................. 5-9
Chapter 6 Power and Power-Up Modes
Power conditions ................................................................................ 6-1
Power indicators ................................................................................ 6-4
Battery indicators ................................................................................ 6-4
DC IN indicator .................................................................................... 6-4
Power indicator ................................................................................... 6-5
Battery types ....................................................................................... 6-5
Main battery ........................................................................................ 6-5
Secondary battery (option) .................................................................. 6-6
Real time clock battery ....................................................................... 6-6
Care and use of the Battery Pack ..................................................... 6-7
Safety precautions .............................................................................. 6-7
Charging the batteries ......................................................................... 6-8
Monitoring battery capacity ................................................................. 6-9
Maximizing battery operating time .................................................... 6-10
Retaining data with power off ............................................................. 6-10
Extending battery life ........................................................................ 6-11
Replacing the Battery Pack ............................................................. 6-11
Removing the Battery Pack ............................................................... 6-12
Installing the Battery Pack ................................................................ 6-13
Starting the computer by password ................................................ 6-14
xv
Chapter 7 HW Setup and Passwords
HW Setup ............................................................................................ 7-1
Accessing HW Setup .......................................................................... 7-1
HW Setup window ............................................................................... 7-2
Supervisor password .......................................................................... 7-9
Chapter 8 Optional Devices
PC cards .............................................................................................. 8-2
Installing a PC card ............................................................................. 8-2
Removing a PC card ........................................................................... 8-4
SD cards .............................................................................................. 8-5
Installing an SD card ........................................................................... 8-5
Removing an SD card .......................................................................... 8-6
Memory expansion ............................................................................. 8-6
Installing memory module ................................................................... 8-7
Removing memory module .................................................................. 8-9
Battery Pack ...................................................................................... 8-10
High Capacity 2nd Battery Pack ...................................................... 8-10
Universal AC Adaptor ....................................................................... 8-10
Battery Charger ................................................................................ 8-11
USB FDD Kit ...................................................................................... 8-11
Slim Port Replicator ......................................................................... 8-11
Ports ................................................................................................. 8-11
High Capacity 2nd Battery Pack ....................................................... 8-12
External monitor ............................................................................... 8-12
Security lock ..................................................................................... 8-13
Chapter 9 Troubleshooting
Problem solving process .................................................................... 9-1
Preliminary checklist ........................................................................... 9-1
Analyzing the problem ........................................................................ 9-2
Hardware and system checklist ......................................................... 9-3
System start-up .................................................................................. 9-3
Self test .............................................................................................. 9-4
Power ................................................................................................. 9-4
Password ............................................................................................ 9-7
Keyboard ............................................................................................ 9-8
LCD panel ........................................................................................... 9-8
Hard disk drive .................................................................................... 9-9
xiii
Diskette drive .................................................................................... 9-10
Infrared port ....................................................................................... 9-10
Pointing device .................................................................................. 9-11
PC card ............................................................................................ 9-13
SD card ............................................................................................ 9-13
Monitor ............................................................................................. 9-14
Sound system .................................................................................. 9-14
USB .................................................................................................. 9-15
Modem ............................................................................................. 9-15
LAN .................................................................................................. 9-17
Wireless LAN .................................................................................... 9-17
TOSHIBA support .............................................................................. 9-18
Before you call .................................................................................. 9-18
Where to write .................................................................................. 9-18
Appendixes
Appendix A
Specifications ..................................................................................... A-1
Appendix B
Display Controller and Modes ...........................................................B-1
Appendix C
AT Commands ....................................................................................C-1
Appendix D
S-registers ........................................................................................... D-1
Appendix E
V.90 ...................................................................................................... E-1
Appendix F
Wireless LAN ....................................................................................... F-1
Appendix G
AC Power Cord and Connectors ....................................................... G-1
Appendix H
Internal Modem Guide .......................................................................H-1
Appendix I
Parts Numbers ..................................................................................... I-1
xvii
Glossary
Index
xviii
Preface
Congratulations on your purchase of the TOSHIBA 2000 computer. This powerful,
lightweight notebook computer is designed to provide years of reliable, highperformance computing.
This manual tells how to set up and begin using your 2000 computer. It also
provides detailed information on configuring your computer, basic operations and
care, using optional devices and troubleshooting.
If you are a new user of computers or if you’re new to portable computing, first read
over the Introduction and The Grand Tour chapters to familiarize yourself with the
computer’s features, components and accessory devices. Then read Getting Started
for step-by-step instructions on setting up your computer.
If you are an experienced computer user, please continue reading the preface to
learn how this manual is organized, then become acquainted with this manual by
browsing through its pages. Be sure to look over the Special features section of the
Introduction, to learn about features that are uncommon or unique to the computers
and carefully read HW Setup and Passwords. If you are going to install PC cards or
connect external devices such as a monitor, be sure to read Chapter 8, Optional
Devices.
Manual contents
This manual is composed of nine chapters, nine appendixes, a glossary, and an
index.
Chapter 1, Introduction, is an overview of the computer’s features, capabilities, and
options.
Chapter 2, The Grand Tour, identifies the components of the computer and briefly
explains how they function.
Chapter 3, Getting Started, provides a quick overview of how to begin operating
your computer and gives tips on safety and designing your work area.
Chapter 4, Operating Basics, includes instructions on using the following devices:
Touch Pad, external diskette drive, wireless communication features, LAN and
internal modem.
Chapter 5, The Keyboard, describes special keyboard functions including the
keypad overlay and hotkeys.
xix
User's Manual
Chapter 6, Power and Power-Up Modes, gives details on the computer’s power
resources and battery save modes.
Chapter 7, HW Setup and Passwords, explains how to configure the computer using
the HW Setup program. It also tells how to set a password.
Chapter 8, Optional Devices, describes the optional hardware available.
Chapter 9, Troubleshooting, provides helpful information on how to perform some
diagnostic tests, and suggests courses of action if the computer doesn’t seem to be
working properly.
The Appendixes provide technical information about your computer.
The Glossary defines general computer terminology and includes a list of acronyms
used in the text.
The Index quickly directs you to the information contained in this manual.
Conventions
This manual uses the following formats to describe, identify, and highlight terms
and operating procedures.
Abbreviations
On first appearance, and whenever necessary for clarity, abbreviations are enclosed
in parentheses following their definition. For example: Read Only Memory
(ROM). Acronyms are also defined in the Glossary.
Icons
Icons identify ports, dials, and other parts of your computer. The indicator panel
also uses icons to identify the components it is providing information on.
Keys
The keyboard keys are used in the text to describe many computer operations. A
distinctive typeface identifies the key top symbols as they appear on the keyboard.
For example, Enter identifies the Enter key.
xx
Conventions
Key operation
Some operations require you to simultaneously use two or more keys. We identify
such operations by the key top symbols separated by a plus sign (+). For example,
Ctrl + C means you must hold down Ctrl and at the same time press C. If three
keys are used, hold down the first two and at the same time press the third.
ABC
When procedures require an action such as clicking an icon or entering
text, the icon’s name or the text you are to type in is represented in the
type face you see to the left.
Display
ABC
Names of Windows® or icons or text generated by the computer that
appears on its display screen is presented in the type face you see to the
left.
Messages
Messages are used in this manual to bring important information to your attention.
Each type of message is identified as shown below.
CAUTION: Pay attention! A caution informs you that improper use of
equipment or failure to follow instructions may cause data loss or
damage your equipment.
NOTE: Please read. A note is a hint or advice that helps you make best
use of your equipment.
xxi
User's Manual
xxii
General Precautions
TOSHIBA computers are designed to optimize safety, minimize strain and withstand
the rigors of portability. However, certain precautions should be observed to further
reduce the risk of personal injury or damage to the computer.
Be certain to read the general precautions below and to note the cautions included
in the text of the manual.
Stress injury
Carefully read the Instruction Manual for Safety & Comfort. It contains information
on prevention of stress injuries to your hands and wrists than can be caused by
extensive keyboard use. Chapter 3, Getting Started, also includes information on
work space design, posture and lighting that can help reduce physical stress.
Heat injury
Avoid prolonged physical contact with the computer. If the computer is used for
long periods, its surface can become very warm. While the temperature will not feel
hot to the touch, if you maintain physical contact with the computer for a long time
(if you rest the computer on your lap or if you keep your hands on the palm rest, for
example) your skin might suffer low-heat injury.
Also, if the AC adaptor has been used for a long time, avoid prolonged physical
contact with the AC adaptor. It can become very warm.
Pressure or impact damage
Do not apply heavy pressure to the computer or subject it to strong impact.
Excessive pressure or impact can cause damage to computer components or
otherwise cause malfunctions.
PC card overheating
Some PC cards can become hot with prolonged use. Overheating of a PC card can
result in errors or instability in the PC card operation. Also be careful when you
remove a PC card that has been used for a long time.
xxiii
User's Manual
xxiv
Introduction
This chapter provides an equipment checklist, and it identifies the computer’s
features, options and accessories.
CAUTION: Some of the features described in this manual may not
function properly if you use an operating system that was not preinstalled
by TOSHIBA.
Equipment checklist
Carefully unpack your computer. Save the box and packing materials for future use.
Check to make sure you have all the following items:
◆
PORTÉGÉ 2000 Portable Personal Computer
◆
Universal AC Adaptor and power cord
◆
Modular cable
The computer is configured with one of three sets of preinstalled software, manual
packages and auxiliary media depending on your choice of operating system.
“Windows XP” is the Microsoft® Windows® XP Professional operating system.
“Windows 2000” is the Microsoft® Windows® 2000 Professional operating
system.
Windows XP
◆
The following software is preinstalled:
•
•
•
•
•
•
•
•
Microsoft® Windows XP Professional
TOSHIBA Wireless LAN Driver
TOSHIBA Software Modem Driver
TOSHIBA SD card Driver
TOSHIBA Utilities
TOSHIBA Hotkey Utility for Display Devices
TOSHIBA Power Saver
TOSHIBA Moblile Extention
1-1
INTRODUCTION
Chapter 1
INTRODUCTION
User's Manual
•
•
•
•
•
•
•
•
◆
Documentation:
•
•
•
•
•
◆
TOSHIBA Common Modules
TOSHIBA Controls
TOSHIBA Console
TOSHIBA Client Manager
TOSHIBA Network Device Switch
SPANworks 2000 Professional
TOSHIBA Skins for Windows Media Player
Online manual
2000 Portable Personal Computer User’s Manual
Microsoft Windows XP Professional manual package
Instruction Manual for Safety & Comfort
End User License Agreement
International Limited Warranty (ILW) Instruction
(This instruction is included only with computers sold in ILW supported
areas.)
Product Recovery CD-ROM (contains TOSHIBA Management Console, which
is not preinstalled)
Windows 2000 Service Pack 2
◆
Use the Product Recovery CD-ROM to install the following software. Refer to
the Windows XP Professional/2000 setup section in Chapter 3, Getting
Started.
• Microsoft® Windows 2000
• The same preinstalled software that is supplied with Windows XP Professional.
◆
Documentation:
• Microsoft Windows 2000 manual package
• The same documentation that is supplied with Windows XP Professional.
If any of the items are missing or damaged, contact your dealer immediately.
1-2
Features
The computer uses TOSHIBA’s advanced Large Scale Integration (LSI),
Complementary Metal-Oxide Semiconductor (CMOS) technology extensively to
provide compact size, minimum weight, low power usage, and high reliability. This
computer incorporates the following features and benefits:
Processor
Built-in
Ultra Low Voltage Mobile Intel® Pentium® III processor
750 MHz-M with Enhanced Intel® SpeedStep™ Technology incorporates a math coprocessor and 32 KB cache.
Built-in
256 MB of memory is installed on the main board.
Memory
Slots
Level 2 cache
Video RAM
A 256 MB memory module can be installed in the memory
slot for a maximum of 512 MB system memory.
A 512 KB level 2 cache is provided to maximize performance.
16 MB of RAM is provided for video display.
(occupied from system memory)
Disks
Built-in
Hard disk
20 billion bytes (18.62 GB)
Display
The computer’s LCD panel supports high-resolution video graphics. The screen
can be set at a wide range of viewing angles for maximum comfort and readability.
Built-in
12.1" XGA-TFT, 1024 horizontal x 768 vertical pixels, up
to 16 M colors
Graphics controller
A 128-bit graphics controller maximizes display
performance. Refer to Appendix B for more information.
1-3
INTRODUCTION
Features
INTRODUCTION
User's Manual
Keyboard
Built-in
84 keys or 85 keys, compatible with IBM enhanced
keyboard, embedded numeric overlay, dedicated cursor
control,
and
keys.
Touch pad
Built-in
A touch pad and control buttons in the palm rest enable
control of the on-screen pointer and scrolling of windows.
Battery Pack
The computer is powered by one rechargeable lithium-ion
polymer Battery Pack.
RTC battery
The internal RTC battery backs up the Real Time Clock
(RTC) and calendar.
AC adaptor
The universal AC adaptor provides power to the system
and recharges the batteries when they are low. It comes
with a detachable power cord. Because it is universal, it can
receive a range of AC voltage between 100 and 240 volts.
Headphone
Enables connection of a stereo headphone
Microphone
Enables connection of a monaural microphone
Power
Ports
Infrared
External monitor
This infrared port is compatible with Infrared Data
Association (IrDA 1.1) Fast InfraRed (FIR) standards. It
enables cableless 4 Mbps data transfer with IrDA 1.1
compatible external devices.
15-pin, analog VGA port supports VESA DDC2B compatible functions.
Docking
Special port for connecting an optional Slim Port Replicator
or High Capacity 2nd Battery Pack.
Universal Serial Bus
Two Universal Serial Bus (USB) enables chain connection
of a number of USB-equipped devices to one port on your
computer.
1-4
Features
INTRODUCTION
Slots
PC card
A PC card slot accommodates:
One 5 mm Type II
Refer to Chapter 8, Optional Devices, for details.
SD card
The SD card slot accommodates:
SD cards
Refer to Chapter 8, Optional Devices, for details.
Multimedia
Sound System
Windows Sound System compatible sound system
provides internal speaker as well as jacks for an external
microphone and headphone.
Communications
Modem
LAN
Wireless LAN
TOSHIBA Console
button
Internet button
An internal modem provides capability for data and fax
communication. It supports V.90. Refer to Appendix E. The
speed of data transfer and fax depends on analog telephone line conditions. It has a modem jack for connecting
to a telephone line. It is preinstalled as a standard device in
some markets.
The computer is equipped with a LAN card that supports
Ethernet LAN (10 Mbit/s, 10BASE-T) and Fast Ethernet
LAN (100 Mbit/s, 100BASE-Tx). It is preinstalled as a
standard device in some markets.
In some markets, the computer is equipped with a Wireless
LAN mini-PCI card that is compatible with other LAN
systems based on Direct Sequence Spread Spectrum radio
technology that complies with the IEEE 802.11 Standard
(Revision B). It supports data transfer up to 11 Mbit/s. It
has Frequency Channel Selection (2.4 GHz) and allows
roaming over multiple channels.
Press this button to launch an application automatically.
In Windows XP/2000 the default is TOSHIBA Console.
Use the TOSHIBA Control to associate an application to
this button.
Press this button to launch an Internet browser. See
Chapter 2, Grand Tour, for details.
1-5
INTRODUCTION
User's Manual
Security
Security lock slot
Connects an optional security lock to anchor the computer
to a desk or other large object
Software
Operating System
TOSHIBA Utilities
Plug and Play
One of the following operating systems are available
Windows XP/2000. Refer to the preinstalled software
section at the front of this chapter.
A number of utilities and drivers are preinstalled to make
your computer more convenient to use. Refer to the
Utilities section in this chapter.
When you connect an external device to the computer or
when you install a component, Plug and Play capability
enables the system to recognize the connection and make
the necessary configurations automatically.
Special features
The following features are either unique to TOSHIBA computers or are advanced
features, which make the computer more convenient to use.
Hotkeys
1-6
Key combinations let you quickly modify the system
configuration directly from the keyboard without running a
system configuration program.
Keypad overlay
Gray keys with gray lettering make up the keypad overlay,
which lets you use the keyboard for ten-key operations or
cursor control.
Display automatic
power off
This feature automatically cuts off power to the internal
display when there is no keyboard input for a time
specified. Power is restored when any key is pressed. You
can specify the time in the Turn off monitor item of the
Power Save Mode window in Power Saver.
HDD automatic
power off
This feature automatically cuts off power to the hard disk
drive when it is not accessed for a time specified. Power is
restored when the hard disk is accessed. You can specify
the time in the Turn off hard disks item of the Power Save
Mode window in Power Saver.
Special features
This feature automatically turns off power to the system
when there is no input for a time specified. You can specify
the time in the System standby or System hibernate item of
the System Power Mode window in Power Saver.
Battery save mode
This feature lets you save battery power. You can specify
the Power Save Mode in the Running on batteries item of
the Power Save Modes window in Power Saver.
Power on password
Two levels of password security are available: supervisor
and user. This feature prevents unauthorized access to your
computer.
Instant security
A hotkey function blanks the screen and disables the
computer providing quick and easy data security.
Panel power on/off
This feature turns power to the computer off when the
display panel is closed and turns it back on when the panel
is opened. You can specify the setting in the When I close
the lid item of the System Power Mode window in Power
Saver.
Auto power on
This feature lets you set a time and date for the computer
to turn on automatically. The feature is useful for receiving
remote communications while you are asleep or away.
You can specify the setting in Scheduled Tasks.
Standby
Hibernation
If you have to interrupt your work, you can turn off the
power without exiting from your software. Data is
maintained in the computer’s main memory. When you
turn on the power again, you can continue working right
where you left off.
This feature lets you turn off the power without exiting
from your software. The contents of main memory is saved
to the hard disk, when you turn on the power again, you
can continue working right where you left off.
1-7
INTRODUCTION
System automatic
power off
INTRODUCTION
User's Manual
Heat dispersal
To protect from overheating, the CPU has an internal
temperature sensor. If the computer’s internal temperature
rises to a certain level, the cooling fan is turned on or the
processing speed is lowered. Use the Fan item of the
Power Save Modes window in Power Saver.
Maximum
Performance
Turns on fan first, then if necessary
lowers CPU processing speed.
Performance
Uses a combination of fan and
lowering the CPU processing speed.
Battery optimized
Lowers the CPU processing speed
first, then if necessary turns on the
fan.
Utilities
This section describes preinstalled utilities and tells how to start them. For details
on operations, refer to each utility’s online manual, help files or readme files.
TOSHIBA Power Saver To access this power savings management program in
Windows 2000, open the Control Panel and double-click
the TOSHIBA Power Saver icon. In Windows XP, open the
Control Panel, click Performance and Maintenance and
click the TOSHIBA Power Saver icon.
HW Setup
Fn-esse
Supervisor Password
Utility for Windows
1-8
This program lets you customize your hardware settings
according to the way you work with your computer and the
peripherals you use. To start the utility in Windows 2000,
open the Control Panel and double-click the TOSHIBA
HW Setup icon. In Windows XP, open the Control Panel,
click Printers and Other Hardware and click the TOSHIBA
HW Setup icon.
This Windows program lets you define your own “shortcut” keys to quickly launch applications and speed your
work in Windows. To start the utility, click the Windows
Start button, point to Programs (Windows XP only, point
to All Programs), point to TOSHIBA Utilities and click Fnesse.
This utility for Windows lets you register a Supervisor
Password, which restricts access to HW Setup.
Utilities
The display driver enables simultaneous display on the
internal LCD, and on an external computer monitor. To
enable this function, use the Display Properties dialogue
box.
Sound drivers
A broad range of audio controls are possible through the
ALi sound driver, including Software Synthesize, Mic
volume and Power management. Click Control Panel and
click the ALi sound setup icon to adjust power management settings.
For other sound settings, use the Windows Device
Manager, Multimedia panel or volume control dial.
LAN drivers
This preinstalled driver makes the computer LAN-ready for
a computer running Windows 2000. To make LAN
settings, click Start, point to Settings, click Control Panel
and double-click the Network icon.
TOSHIBA Accessibility This utility lets you make the Fn key sticky, that is, you
can press it once, release it, and they press an “F number”
key. The Fn key remains active until another key is
pressed.
Hotkey utility
This utility lets you display or hide a confirmation message
when you press Fn + F3 or Fn + F4.
TOSHIBA Controls
Use this utility to customize TOSHIBA Console button
settings.
TOSHIBA Console
TOSHIBA Console is a graphical user interface that
provides easy access to help and services. It is the default
function launched by the TOSHIBA Console button.
1-9
INTRODUCTION
Display Driver
for Windows
INTRODUCTION
User's Manual
Options
You can add a number of options to make your computer even more powerful
and convenient to use. The following options are available:
Memory expansion
One memory expansion slot is available for installing a 256
MB memory module. The modules are SD Random Access
Memory (SD-RAM).
Battery Pack
An Battery Pack (PA3154U) can be purchased from your
TOSHIBA dealer. The Battery Pack is identical to the one
that came with your computer. Use it as a spare or replacement.
High Capacity 2nd
Battery Pack
This Battery Pack (PA3155U) increases your computer’s
operating time when a main Battery Pack is also installed.
Universal AC Adaptor If you use your computer at more than one site, it may be
convenient to purchase an additional Universal AC
Adaptor for each site so you will not have to carry the
adaptor with you.
USB FDD Kit
Battery Charger
Security lock
Slim Port Replicator
1-10
A 3 1/2" diskette drive accommodates 1.44-megabyte or
720-kilobyte diskettes. It connects to a USB port. (Windows XP does not support 720-kilobyte diskettes.)
The Battery Charger lets you charge extra batteries outside
the computer.
A slot is available to attach a security cable to the computer to deter theft.
The Slim Port Replicator provides the following: an external
monitor port, four USB ports, a port for charging a High
Capacity 2nd Battery Pack, a LAN jack and a DC-IN
socket.
Chapter 2
The Grand Tour
Front with the display closed
Figure 2-1 shows the computer’s front with its display panel in the closed position.
POWER SOURCE/SYSTEM INDICATORS
DISPLAY LATCH
Figure 2-1 Front of the computer with display closed
Display latch
Power source/
system indicators
This latch secures the LCD panel in its closed position.
Push the latch to open the display.
LEDs let you monitor the status of various computer
functions. Details are given in the Indicators section.
2-1
THE GRAND TOUR
This chapter identifies the various components of your computer. Become familiar
with each component before you operate the computer.
User's Manual
Left side
Figure 2-2 shows the computer’s left side.
THE GRAND TOUR
SECURITY LOCK SLOT
SD CARD INDICATOR
SD CARD SLOT
FAN VENT
Figure 2-2 The left side of the computer
Security lock
slot
Fan vent
A security cable attaches to this slot. The optional security
cable anchors your computer to a desk or other large object
to deter theft.
Provides air flow for the fan.
CAUTION: Be careful not to block the fan vent. Also be careful to keep
foreign objects out of the vents. A pin or similar object can damage the
computer’s circuitry.
SD card slot
This slot lets you transfer data from the device to your
computer.
CAUTION: Keep foreign objects out of the SD card slot. A pin or similar
object can damage the computer’s circuitry.
SD card indicator
2-2
This indicator glows green when the computer is
accessing the SD card Slot.
Right side
Right side
Figure 2-3 shows the computer’s right side.
WIRELESS COMMUNICATION SWITCH
PC CARD SLOT
THE GRAND TOUR
HEADPHONE JACK MICROPHONE JACK INFRARED PORT
Figure 2-3 The right side of the computer
Wireless
communication
switch
Off On
Slide this switch to the right to turn on Wireless LAN.
Slide it to the left to turn off the functions. (This switch
is only on models with Wireless LAN functions.)
Headphone jack
A standard 3.5 mm mini headphone jack enables connection of a stereo headphone (16 ohm minimum) or other
device for audio output. When you connect headphones,
the internal speaker is automatically disabled.
Microphone jack
A standard 3.5 mm mini microphone jack enables connection of a monaural microphone or other device for audio
input.
Infrared port
PC card slot
CB
This infrared port is compatible with Infrared Data Association (IrDA 1.1) standards. It enables cableless 4 Mbps,
1.152 Mbps, 115.2 kbps, 57.6 kbps, 38.4 kbps, 19.2 kbps or
9.6 kbps data transfer with IrDA 1.1 compatible external
devices.
A PC card slot can accommodate one 5 mm PC card (Type
II). The slot supports 16-bit PC cards and CardBus PC
cards.
CAUTION: Keep foreign objects out of the PC card slot. A pin or similar
object can damage the computer’s circuitry.
2-3
User's Manual
Back side
THE GRAND TOUR
Figure 2-4 shows the computer’s back side.
LAN INDICATOR
MODEM JACK
LAN JACK
EXTERNAL MONITOR PORT
USB PORTS
DC IN 15V
Figure 2-4 The computer’s back side
Modem jack
In areas where an internal modem is installed as standard
equipment, there is a modem jack that lets you use a
modular cable to connect the modem directly to a telephone line. The modem is not supported in some marketing
regions.
CAUTIONS: 1. In case of a lightning storm, unplug the modem cable
from the telephone jack.
2. Do not connect the modem to a digital telephone line.
A digital line will damage the modem.
LAN jack
Ether
LAN indicator
Universal
Serial Bus
port
External monitor
port
DC IN 15V
DC IN 15V
2-4
This jack lets you connect to a LAN. The adaptor has
built-in support for Ethernet LAN (10 megabits per second,
10BASE-T) and Fast Ethernet LAN (100 megabits per
second, 100BASE-Tx).
This indicator glows green when the computer is
accessing the LAN.
The Universal Serial Bus (USB) port enables chain
connection of a number of USB-equipped devices to one
port on your computer. For example, you might connect a
USB-HUB to the computer, then connect a keyboard to the
USB-HUB and a mouse to the keyboard.
This 15-pin port lets you connect an external monitor.
The AC adaptor connects to this socket. Use only the
model of AC adaptor that comes with the computer. Using
the wrong adaptor can damage your computer.
Underside
Underside
Figure 2-5 shows the underside of the computer. Make sure the display is closed
before turning over your computer.
MEMORY MODULE DOCKING
DOCKING
DOCKING
PORT
COVER
BATTERY
HOLE
SPEAKER
LOCK
BATTERY
PACK
Figure 2-5 The underside of the computer
Docking port
Use this port to connect an optional Slim Port Replicator or
High Capacity 2nd Battery Pack.
CAUTION: Keep foreign objects out of the docking port. A pin or similar
object can damage the computer’s circuitry.
Docking holes
These holes ensure a proper connection between the
computer and an optional High Capacity 2nd Battery Pack.
Expansion
memory socket
Use this socket to install a memory module to increase
your computer’s memory by 256 MB. Refer to the Memory
expansion section in Chapter 8, Optional Devices.
Battery Pack
The Battery Pack powers the computer when the AC
adaptor is not connected. The Batteries section in Chapter
6, Power and Power-Up Modes, describes how to access
the Battery Pack. Battery Packs can be purchased from
your TOSHIBA dealer to extend the computer’s battery
operating time.
2-5
THE GRAND TOUR
HOLES
User's Manual
Battery lock
THE GRAND TOUR
Speaker
A sliding lock prevents inadvertent release of the Battery
Pack.
The speaker emits sound generated by your software as
well as audio alarms, such as low battery condition,
generated by the system.
Front with the display open
Figure 2-6 shows the front of the computer with the display open. To open the
display, push the display latch on the front of the computer and lift the display up.
Position the display at a comfortable viewing angle.
INTERNET
DISPLAY SCREEN
BUTTON
TOSHIBA CONSOLE
BUTTON
DISPLAY HINGE
DISPLAY
SENSOR
HINGE
SWITCH
POWER
BUTTON
TOUCH PAD
TOUCH PAD CONTROL BUTTONS
Figure 2-6 The front with the display open
2-6
Front with the display open
Display screen
The full-color LCD displays high-contrast text and
graphics and is compatible with the industry standard
Video Graphics Array (VGA). The LCD consists of up to
1024 × 768 pixels or dots. The computer has a Thin-Film
Transistor (TFT) display. Refer to Appendix B.
Display hinge
The display hinge holds the display screen at easy-to-view
angles.
Power button
Press the power button to turn the computer’s power on
and off.
Internet button
TOSHIBA Console
button
Press this button to launch an Internet browser. If the
computer’s power is off, you can press this button to turn
on the computer’s power and launch the browser automatically in one step.
Press this button to launch an application automatically.
The default is TOSHIBA Console.
Touch pad
A Touch pad located in the center of the palm rest is used
to control the on-screen pointer. Refer to the Using the
Touch pad section in Chapter 4, Operating Basics.
Touch pad
control buttons
Control buttons below the Touch pad let you select menu
items or manipulate text and graphics designated by the
on-screen pointer.
Sensor switch
This switch shuts down the computer when you close the
cover and the panel power on/off feature is enabled.
2-7
THE GRAND TOUR
When the computer operates on power through the AC
adaptor, the display screen’s image will be somewhat
brighter than when it operates on battery power. The lower
brightness level is intended to save battery power.
User's Manual
Indicators
Figure 2-7 shows the indicators, which light when various computer operations are in
progress.
WIRELESS
SECONDARY
MAIN
DISK
THE GRAND TOUR
BATTERY
BATTERY
COMMUNICATION
POWER
DC IN
Figure 2-7 The power source/system indicators
Power source/system indicators
DC IN
Power
The Power indicator glows green when the computer is
on. If you turn off the computer in Resume mode, this
indicator blinks orange (one second on, two seconds off)
while the computer shuts down.
Main battery
The Main battery indicator shows the condition of the
charge. Green means fully charged and orange means being
charged. Refer to Chapter 6, Power and Power-Up Modes.
Secondary
battery
The Secondary battery indicator shows the condition of
the charge of an optional High Capacity 2nd Battery Pack.
Green means fully charged and orange means being
charged. Refer to Chapter 6, Power and Power-Up Modes.
2
2-8
The DC IN indicator glows green when DC power is
supplied from the AC power adaptor. If the adaptor’s
output voltage is abnormal or if the power supply malfunctions, this indicator flashes orange.
Indicators
Disk
Wireless
communication
The Disk indicator glows green when the computer is
accessing a disk drive.
The figures below show the positions of the keypad overlay indicators and the
CapsLock indicator.
When the F10 key indicator glows, the keypad overlay lets you control the cursor.
When the F11 key indicator glows, the keypad overlay lets you enter numbers.
NUMERIC MODE
ARROW MODE
Figure 2-8 Keypad overlay indicators
When the CapsLock indicator glows, the keyboard is in all-caps mode.
CAPS LOCK
Figure 2-9 CapsLock indicator
2-9
THE GRAND TOUR
The Wireless communication indicator lights when the
Wireless LAN function is turned on. (This indicator is used
only models with Wireless LAN functions.)
User's Manual
Keyboard indicator
Caps Lock
THE GRAND TOUR
Arrow mode
Numeric mode
This indicator glows green when the alphabet keys are
locked in uppercase.
When the Arrow mode indicator lights green, you can
use the keypad overlay (white labeled keys) as cursor
keys. Refer to the Keypad overlay section in Chapter 5,
The Keyboard.
You can use the keypad overlay (white labeled keys) for
numeric input when the Numeric mode indicator lights
green. Refer to the Keypad overlay section in Chapter 5,
The Keyboard.
AC adaptor
The AC adaptor converts AC power to DC power and reduces the voltage supplied
to the computer. It can automatically adjust to any voltage from 100 to 240 volts and
to a frequency of either 50 or 60 hertz, enabling you to use the computer in almost
any region.
To recharge the battery, simply connect the AC adaptor to a power source and the
computer. See Chapter 6 Power and Power-Up Modes for details.
Figure 2-10 The AC adaptor
CAUTION: Use only the AC adaptor that came with the computer or an
equivalent optional adaptor. Use of the wrong adaptor could damage
your computer. TOSHIBA assumes no liability for any damage in such
case.
2-10
Chapter 3
Getting Started
This chapter provides basic information to get you started using your computer. It
covers the following topics:
◆
Setting up your work space — for your health and safety
NOTE: Be sure also to read Instruction Manual for Safety & Comfort. This
guide, which is included with the computer, explains product liability.
Opening the display
◆
Connecting the AC adaptor
◆
Turning on the power
◆
Windows XP Professional/2000 setup
◆
Turning off the power
◆
Restarting the computer
◆
Restoring the Windows system
GETTING STARTED
◆
If you are a new user, follow the steps in each section of this chapter as you prepare
to operate your computer.
NOTE: All users should be sure to carefully read the sections Windows
XP Professional/2000 setup, which describe actions to take when you
turn on the power for the first time.
3-1
User's Manual
Setting up your work space
GETTING STARTED
Establishing a comfortable work site is important for you and your computer. A
poor work environment or stressful work habits can result in discomfort or
serious injury from repetitive strain to your hands, wrists or other joints. Proper
ambient conditions should also be maintained for the computer’s operation. This
section discusses the following topics:
◆
General conditions
◆
Placement of the computer and peripheral devices
◆
Seating and posture
◆
Lighting
◆
Work habits
General conditions
In general, if you are comfortable, so is your computer, but read the following to
make sure your work site provides a proper environment.
◆
Make sure there is adequate space around the computer for proper ventilation.
◆
Make sure the AC power cord connects to an outlet that is close to the
computer and easily accessible.
◆
The temperature should be 5 to 35 degrees Centigrade (41 to 95 degrees
Fahrenheit) and the relative humidity should be 20 to 80 percent.
◆
Avoid areas where rapid or extreme changes in temperature or humidity may
occur.
◆
Keep the computer free of dust, moisture, and exposure to direct sunlight.
◆
Keep the computer away from heat sources, such as electric heaters.
◆
Do not use the computer near liquids or corrosive chemicals.
◆
Do not place the computer near objects that create strong magnetic fields
(e.g., stereo speakers).
◆
Do not operate the computer in close proximity to a mobile phone.
Placement of computer
Position the computer and peripheral devices to provide comfort and safety.
◆
3-2
Set the computer on a flat surface at a comfortable height and distance. The
display should be no higher than eye level to avoid eye strain.
Setting up your work space
◆
Place the computer so that it is directly in front of you when you work and
make sure you have adequate space to easily operate other devices.
◆
Allow adequate space behind the computer to let you freely adjust the display.
The display should be angled to reduce glare and maximize visibility.
◆
If you use a paper holder, set it at about the same height and distance as the
computer.
Seating and posture
The height of your chair in relation to the computer and keyboard as well as the
support it gives your body are primary factors in reducing work strain. Refer to the
following tips and to figure 3-1.
GETTING STARTED
BELOW EYE LEVEL
FOOT REST
90O ANGLES
Figure 3-1 Posture and positioning of the computer
◆
Place your chair so that the keyboard is at or slightly below the level of your
elbow. You should be able to type comfortably with your shoulders relaxed.
◆
Your knees should be slightly higher than your hips. If necessary, use a foot
rest to raise the level of your knees to ease pressure on the back of your thighs.
◆
Adjust the back of your chair so it supports the lower curve of your spine.
◆
Sit straight so that your knees, hips and elbows form approximately 90 degree
angles when you work. Do not slump forward or lean back too far.
3-3
User's Manual
Lighting
Proper lighting can improve legibility of the display and reduce eye strain.
◆
Position the computer so that sunlight or bright indoor lighting does not reflect
off the screen. Use tinted windows, shades or other screen to eliminate sun
glare.
◆
Avoid placing the computer in front of bright light that could shine directly in
your eyes.
◆
If possible, use soft, indirect lighting in your computer work area. Use a lamp to
illuminate your documents or desk, but be sure to position the lamp so that it
does not reflect off the display or shine in your eyes.
GETTING STARTED
Work habits
A key to avoiding discomfort or injury from repetitive strain is to vary your activities. If possible, schedule a variety of tasks into your work day. If you must spend
long periods at the computer, finding ways to break up the routine can reduce
stress and improve your efficiency.
◆
Sit in a relaxed posture. Good positioning of your chair and equipment as
described earlier can reduce tension in your shoulders or neck and ease back
strain.
◆
Vary your posture frequently.
◆
Occasionally stand up and stretch or exercise briefly.
◆
Exercise and stretch your wrists and hands a number of times during the day.
◆
Frequently, look away from the computer and focus your eyes on a distant
object for several seconds, for example 30 seconds every 15 minutes.
◆
Take frequent short breaks instead of one or two long breaks, for example, two
or three minutes every half hour.
◆
Have your eyes examined regularly and visit a doctor promptly, if you suspect
you might be suffering from a repetitive strain injury.
A number of books are available on ergonomics and repetitive strain injury or
repetitive stress syndrome. For more information on these topics or for pointers on
exercises for such stress points as hands and wrists, please check with your library
or book vendor. Also refer to the computer’s Instruction Manual for Safety &
Comfort.
3-4
Connecting the AC adaptor
Opening the display
The display panel can be rotated in a wide range of angles for optimal viewing.
1. Push down the display latch on the front of the computer to unlatch the
display panel.
2. Lift the panel up and adjust it to the best viewing angle for you.
NOTE: When you open the display, hold it with both hands and lift up
slowly.
GETTING STARTED
Figure 3-2 Opening the display panel
Connecting the AC adaptor
Attach the AC adaptor when you need to charge the battery or you want to operate
from AC power. It is also the fastest way to get started, because the Battery Pack
will need to be charged before you can operate from battery power.
The AC adaptor can be connected to any power source supplying from 100 to 240
volts and 50 or 60 hertz. For details on using the AC adaptor to charge the Battery
Pack, refer to Chapter 6, Power and Power-Up Modes.
CAUTION: Use only the AC adaptor that came with the computer or an
equivalent optional adaptor. Use of the wrong adaptor could damage
your computer. TOSHIBA assumes no liability for any damage in such
case.
3-5
User's Manual
1. Connect the power cord to the AC adaptor.
GETTING STARTED
Figure 3-3 Connecting the power cord to the AC adaptor
2. Connect the AC adaptor’s DC output plug to the DC IN port on the back of
the computer.
Figure 3-4 Connecting the adaptor to the computer
3. Plug the power cord into a live wall outlet. The Battery and DC IN indicator
on the front of the computer should glow.
3-6
Turning on the power
Turning on the power
This section describes how to turn on the power.
NOTE: After you turn on the power for the first time, do not turn it off
until you have set up the operating system (OS) and the OS has started
up.
1. If the external diskette drive is connected, make sure it is empty. If a diskette is
in the drive, press the eject button and remove the diskette.
2. Open the display panel.
3. Press and hold the button for two or three seconds.
GETTING STARTED
Figure 3-5 Turning on the power
3-7
User's Manual
Windows XP Professional/2000 setup
When you first turn on the power, the computer’s initial screen is the Microsoft
Windows XP Professional Startup Screen Logo.
Follow the on-screen directions.
If you ordered Windows 2000, the operating system is not preinstalled. Follow the
steps below to install the Windows 2000 and TOSHIBA utilities.
1. Turn on the computer, load the Product Recovery CD-ROM in the drive and
turn off the power.
2. Hold down the C key and turn on the power. When In Touch with
Tomorrow TOSHIBA appears, release the C key.
GETTING STARTED
3. Follow the on-screen instructions.
NOTE: You can get the Product key from a seal on the bottom of the
computer (Windows 2000 only).
Turning off the power
The power can be turned off in one of the following modes: Shut down (Boot),
Hibernation or Standby mode.
Shut Down mode (Boot mode)
When you turn off the power in Shut Down mode, no data is saved and the
computer will boot to the operating system’s main screen.
1. If you have entered data, save it to the hard disk or to a diskette.
2. Make sure all disk activity has stopped, then remove any CDs or diskette.
CAUTION: Make sure the Disk is off. If you turn off the power while a
disk is being accessed, you can lose data or damage the disk.
3. If you are using Windows XP, click start then click Turn off computer.
From the Turn off computer menu select Turn off .
If you are using Windows 2000, click Start and click Shut Down. From the
Shut Down menu select Shut Down.
3-8
Turning off the power
4. Turn off the power to any peripheral devices.
CAUTION: Do not turn the computer or devices back on immediately.
Wait a moment to let all capacitors fully discharge.
Hibernation mode
The hibernation feature saves the contents of memory to the hard disk when the
computer is turned off. The next time the computer is turned on, the previous state
is restored. The hibernation feature does not save the status of peripheral devices.
GETTING STARTED
CAUTIONS: 1. While entering hibernation mode, the computer saves
the contents of memory to the HDD. Data will be lost if
you remove the battery or disconnect the AC adaptor
before the save is completed. Wait for the Disk
indicator to go out.
2. Do not install or remove a memory module while the
computer is in hibernation mode. Data will be lost.
Benefits of hibernation
The hibernation feature provides the following benefits:
◆
Saves data to the hard disk when the computer automatically shuts down
because of a low battery.
NOTE: For the computer to shut down in hibernation mode, the hibernation feature must be enabled in two places in TOSHIBA Power Saver: the
Hibernate window and the Battery Alarm item of the Alarm window.
Otherwise, the computer will shut down in Standby mode. If battery power
becomes depleted, data saved in Standby will be lost.
◆
You can return to your previous working environment immediately when you
turn on the computer.
◆
Saves power by shutting down the system when the computer receives no
input or hardware access for the duration set by the System hibernate feature.
◆
You can use the panel power off feature.
3-9
User's Manual
Starting Hibernation
To enter Hibernation mode, follow the steps below.
Windows XP
1. Click Start.
2. Select Turn Off Computer.
3. Open the Turn Off Computer dialog box. Hibernate is not displayed.
4. Press the Shift key. The Standby item will change to Hibernate.
5. Select Hibernate.
Windows 2000
GETTING STARTED
1. Click Start and click Shut Down.
2. In Shut Down Windows select Hibernate and click the OK button.
The computer will also enter Hibernate mode automatically when you:
◆
Press the power button.
◆
Close the lid.
First, however, make the appropriate settings according to the steps below.
Windows XP/2000
1. In Windows XP, open the Control Panel, click Performance and
Maintenance and click the TOSHIBA Power Saver icon.
In Windows 2000, open the Control Panel and double-click the TOSHIBA
Power Saver icon.
2. Select the Hibernate window, select the Enable Hibernate support check
box and click the Apply button.
3. Select the Power Save Modes window.
4. Double-click Power Save Mode and open the System Power Mode
window.
5. Enable the desired Hibernation settings for When I press the power
button and When I close the lid.
6. Click the OK button.
3-10
Turning off the power
Data save in hibernation mode
When you turn off the power in hibernation mode, the computer takes a moment to
save current memory data to the hard disk. During this time, the Disk indicator will
light.
After you turn off the computer and memory is saved to the hard disk, turn off the
power to any peripheral devices.
CAUTION: Do not turn the computer or devices back on immediately.
Wait a moment to let all capacitors fully discharge.
Standby mode
In standby mode the power remains on, but the CPU and all other devices are in
sleep mode.
◆
Before entering Standby mode, be sure to save your data.
◆
Do not install or remove a memory module while the computer is in standby
mode. The computer or the module could be damaged.
◆
Observe the following precautions regarding standby mode:
• Do not remove the memory module.
• Do not remove the Battery Pack.
Either action could cause the computer to hang up the next time you turn it
on.
The computer could also hang up at power on if it shut down automatically in standby mode because of a low battery.
In any of the above cases, the standby configuration will not be saved.
The following message appears when you turn on the power:
WARNING: RESUME FAILURE.
PRESS ANY KEY TO CONTINUE.
If the computer hangs up when you turn it on, perform the following:
Press the power button and hold it down for five seconds, then turn the
power on again.
3-11
GETTING STARTED
Standby precautions
User's Manual
◆
If you carry the computer on board an aircraft or into a hospital, be sure to shut
down the computer in hibernation mode or in shutdown mode to avoid radio
signal interference.
Benefits of standby
The standby feature provides the following benefits:
◆
Restores the previous working environment more rapidly than does hibernation.
◆
Saves power by shutting down the system when the computer receives no
input or hardware access for the duration set by the System Standby feature.
◆
You can use the panel power off feature.
GETTING STARTED
Executing standby
You can enter standby mode in one of three ways:
1. In Windows XP, click Start, click Turn Off Computer and click Stand by.
In Windows 2000, click Start, click Shut Down, select Stand by and click
OK.
2. Close the display panel. This feature must be enabled. Refer to the System
Power Mode item in Power Saver Utility described in the Control Panel.
In Windows XP, click Performance and Maintenance and click the
TOSHIBA Power Saver icon.
In Windows 2000, double-click the TOSHIBA Power Saver icon.
3.
Press the power button. This feature must be enabled. Refer to the System
Power Mode item in Power Saver Utility described in the Control Panel.
In Windows XP, click Performance and Maintenance and click the
TOSHIBA Power Saver icon.
In Windows 2000, double-click the TOSHIBA Power Saver icon.
When you turn the power back on, you can continue where you left when you shut
down the computer.
NOTES: 1. When the computer is shut down in standby mode, the
power indicator glows orange.
2. If you are operating the computer on battery power, you
can lengthen the operating time by shutting down in
hibernation mode. Standby mode consumes more power.
3-12
Restoring the Windows system
Standby limitations
Standby will not function under the following conditions:
◆
Power is turned back on immediately after shutting down.
◆
Memory circuits are exposed to static electricity or electrical noise.
Restarting the computer
Certain conditions require that you restart the computer system. For example, if:
◆
You change certain computer settings.
◆
An error occurs and the computer does not respond to your keyboard
commands.
There are two ways to restart the computer system:
If you are using Windows 2000, click Start and click Shut Down. From the
Shut Down menu select Restart.
2. Press the power button and hold it down for five seconds. Wait 10 to 15
seconds, then turn the power on again by pressing the power button.
Restoring the Windows system
If preinstalled files are damaged, use the Product Recovery CD-ROM to restore
them. To restore the operating system and all preinstalled software, follow the steps
below.
CAUTION: When you reinstall the Windows operating system, the hard
disk will be reformatted and all data will be lost.
1. Load the Product Recovery CD-ROM in the drive and turn off the computer’s
power.
2. Hold down the C key and turn on the power. When In Touch with
Tomorrow TOSHIBA appears, release the C key.
3. Follow the on-screen instructions.
3-13
GETTING STARTED
1. If you are using Windows XP, click start then click Turn off computer.
From the Turn off computer menu select Restart.
GETTING STARTED
User's Manual
3-14
Chapter 4
Operating Basics
This chapter gives information on basic operations including using the Touch Pad,
the external diskette drive, the wireless communication, LAN and the internal
modem. It also provides tips on caring for your computer and on heat dispersal.
Using the Touch Pad
To use the Touch Pad, simply press and move your finger tip across it in the
direction you want the on-screen pointer to go.
OPERATING BASICS
TOUCH PAD
TOUCH PAD
CONTROL
BUTTONS
Figure 4-1 Touch Pad and Touch Pad control buttons
Two buttons below the keyboard are used like the buttons on a mouse pointer.
Press the left button to select a menu item or to manipulate text or graphics designated by the pointer. Press the right button to display a menu or other function
depending on the software you are using.
CAUTION: Do not press on the touch pad too hard or press a sharp
object such as a ball point pen against the touch pad. The touch pad
could be damaged.
4-1
User's Manual
For some functions, you can tap the touch pad instead of pressing a control button.
Click
Tap the touch pad once
Double-click
Tap the touch pad twice
Drag and drop
1. Hold down the left control button and move the cursor
to drag the item you want to move.
2. Lift your finger to drop the item where you want it.
Scroll
Vertical: Move your finger up or down the right edge of
the touch pad.
Horizontal: Move your finger left or right along the bottom
edge of the touch pad.
Using the USB FDD Kit
A 3 1/2" external diskette drive module connects to the USB port.
NOTE: The USB FDD Kit is an option with some models.
OPERATING BASICS
USB CONNECTOR
DISK-IN-USE
INDICATOR
DISKETTE SLOT
EJECT BUTTON
Figure 4-2 The 3 1/2" USB FDD Kit
Eject button
When a diskette is fully seated in the drive, the eject
button pops out. To remove a diskette, push in the eject
button and the diskette pops out partially for easy removal.
Diskette slot
Insert diskettes in this slot.
Disk-In-Use
Indicator
4-2
This indicator lights when the diskette is being
accessed.
Using the USB FDD Kit
CAUTION: Check the Disk-In-Use indicator when you use the diskette
drive. Do not press the eject button, disconnect a drive cable or turn off
the computer while the light is glowing. Doing so could destroy data and
damage the diskette or the drive.
NOTES: 1. The external diskette drive should be placed on a flat,
horizontal surface when in use. Do not set the drive on an
incline greater than 20o while it is operating.
2. Do not set anything on top of the diskette drive.
3. If you need to boot the computer from the diskette drive or
if you use an OS that does not support USB, you must set
the USB-FDD Legacy Emulation feature in HW Setup to
Enabled. Refer to the USB section in Chapter 7.
Connecting 3 1/2" diskette drive
To connect the drive, plug the diskette drive connector into a USB port. Refer to
Figure 4-3.
NOTE: Make sure the connector is right side up and properly aligned
with the socket. Do not try to force the connection, doing so can damage
the connecting pins.
OPERATING BASICS
Figure 4-3 Connecting the diskette drive to the computer
4-3
User's Manual
NOTE: If you connect the diskette drive after turning on the computer, it
will take about 10 seconds for the computer to recognize the drive. Do
not disconnect and reconnect before 10 seconds has elapsed.
Disconnecting 3 1/2" diskette drive
When you have finished using the diskette drive, follow the procedures below to
disconnect it:
1. Wait for the indicator light to go out to make sure all diskette activity has
stopped.
CAUTION: If you disconnect the diskette drive or turn off the power
while the computer is accessing the drive you may lose data or damage
the diskette or the drive.
2. Pull the diskette drive connector out of the USB port.
Diskette care
OPERATING BASICS
Handle your diskettes with care. The following simple precautions will increase the
lifetime of your diskettes and protect the data you store on them:
1. Store your diskettes in the container they came in to protect them and keep
them clean. If a diskette is dirty, do not use cleaning fluid. Clean it with a soft
damp cloth.
2. Do not slide back the diskette’s protective metal covering or touch the
diskette’s magnetic surface. Fingerprints may prevent the diskette drive from
reading data from the diskette.
3. Data may be lost if the diskette is twisted; bent; or exposed to direct sunlight
or extreme heat or cold.
4. Do not place heavy objects on your diskettes.
5. Do not eat, smoke, or use erasers near your diskettes. Foreign particles inside
the diskette’s jacket can damage the magnetic surface.
6. Magnetic energy can destroy the data on your diskettes. Keep your diskettes
away from speakers, radios, television sets and other sources of magnetic
fields.
4-4
Wireless communications
Wireless communications
The computer’s wireless communication function support wireless LAN. This
section applies only to models with Wireless LAN functions.
Wireless LAN
The wireless LAN is compatible with other LAN systems based on Direct Sequence
Spread Spectrum radio technology that complies with IEEE 802.11 wireless LAN
standard (Revision B). It supports the following features:
◆
Automatic Transmit Rate Select mechanism in the transmit range of 11, 5.5, 2
and 1 Mbit/s.
◆
Frequency Channel Selection (2.4 GHz)
◆
Roaming over multiple channels
◆
Card Power Management
◆
Wired Equivalent Privacy (WEP) data encryption, based on the 128 bit RC4
encryption algorithm as defined in the IEEE 802.11 standard on wireless LANs.
Wake-up on LAN does not function on a wireless LAN.
Wireless communication switch
CAUTION: Set the switch to off in airplanes and hospitals. Check the LED.
It will stop glowing when the wireless communication function is off.
Wireless communication LED
The LED indicates the status of the wireless communication functions.
LED status
Indication
LED off
Wireless communication switch is set to off.
Automatic power down because of overheating.
Power malfunction
LED glows
Wireless communication switch is on.
Wireless LAN is turned on by an application.
4-5
OPERATING BASICS
You can enable or disable wireless LAN function, with the on/off switch. No
transmissions are sent or received when the switch is off. Slide the switch to the
right to turn it on and to the left to turn it off.
User's Manual
If you used the Task Tray icon to disable W-LAN, restart the computer or follow
the procedures below to enable the system to recognize W-LAN. Open or click the
following: Start, Setup, Control Panel, System, Device Manager and
Renew.
LAN
LAN circuits support Ethernet LAN (10 megabits per second, 10BASE-T) and Fast
Ethernet LAN (100 megabits per second, 100BASE-Tx). This section describes how
to connect/disconnect to a LAN.
CAUTION: Do not install or remove an optional memory module while
Wake-up on LAN is enabled.
NOTE: Wake-up on LAN does not work without the AC adaptor. Leave it
connected, if you are using this feature.
OPERATING BASICS
LAN cable types
CAUTION: The computer must be configured properly before connecting
to a LAN. Logging onto a LAN using the computer’s default settings
could cause a malfunction in LAN operation. Check with your LAN
administrator regarding set-up procedures.
If you are using Fast Ethernet LAN (100 megabits per second, 100BASE-TX), be
sure to connect with a CAT5 cable. You cannot use a CAT3 cable.
If you are using Ethernet LAN (10 megabits per second, 10BASE-T), you can
connect with either a CAT5 or a CAT3.
Connecting cable
To connect the LAN cable, follow the steps below.
CAUTION: Connect the AC adaptor before connecting the LAN cable.
The AC adaptor must remain connected during LAN use. If you disconnect the AC Adaptor while the computer is accessing a LAN, the system
may hang up.
1. Turn off the power to the computer and to all external devices connected to
the computer.
4-6
LAN
2. Plug one end of the cable into the LAN’s jack. Press gently until you hear the
latch click into place.
Figure 4-4 Connecting the LAN cable
3. Plug the other end of the cable into a LAN hub connector. Check with your
LAN administrator before connecting to a hub.
Disconnecting cable
To disconnect the LAN cable, follow the steps below.
2. Disconnect the cable from the LAN hub in the same manner. Check with your
LAN administrator before disconnecting from the hub.
4-7
OPERATING BASICS
1. Pinch the lever on the connector in the computer and pull out the connector.
User's Manual
Network Device Switch
This application is used to select one network device on your system and to
prevent inconsistent routing table problems on TCP/IP networks.
Using the switch
To select a network device, follow the steps below.
1. In Windows XP, click start, point to All Programs, click Network Device
Switch.
Left-click the Network Device Switch icon on the Task bar to display a
device menu.
OPERATING BASICS
Figure 4-5 Sample of a network device menu (left click)
2. Click the network device you want to enable. A check will appear beside the
enabled devices. Devices without checks are disabled.
Auto Switch menu
Right-click the Network Device Switch icon to diaplay the Auto Switch menu.
Figure 4-6 Auto Switch menu (right click)
4-8
LAN
Auto Switch
When Auto Switch is selected, this application automatically enables the wireless
LAN device when you disconnect the LAN cable. This feature works only if a wired
LAN device is currently enabled and the LAN uses TCP/IP protocol.
Disabled
Click Disabled to disable or enable this program’s features.
Help
Click Help to display a readme file.
Exit
Click Exit to quit the program.
NOTES: 1. If you change the network device, you might need to log
onto the network again.
2. Log on as the administrator.
1. You start the computer on battery power.
2. You start the computer with the AC adapter connected and disconnect the AC
adapter during operation.
3. You change the Power Saver settings.
4. The computer resumes operation in suspend or hibernation mode.
4-9
OPERATING BASICS
If the Control device power management checkbox in the Device Settings window
of Power Saver is enabled, the following four events will trigger a change in settings
made in the Device Setting window of the Power Saver utility. The change will occur
regardless of the Network Device Switch setting. To avoid these automatic
changes, clear the Control device power management checkbox in the Power
Saver utility. For details, refer to the Power Saver utility’s help files.
User's Manual
Super Long Life scheme
The Super Long Life mode is a scheme of the TOSHIBA Power Saver utility. It is
designed to maximize battery operating time.
In the default setting, wired and wireless LAN functions are disabled. To enable
LAN functions, clear the Control device power management checkbox. Unless this
checkbox is cleared, you will not be able to use LAN functions even if you enable
them with the Network Device Switch. Refer to Power Saver utility help files for
details.
The Super Long Life power saving scheme is not selected as a default.
Using the internal modem
If you purchased a computer model with a preinstalled internal modem, read this
section for directions on connecting the modem. Refer to the online help files for the
internal modem and for details on operation of your modem and modem software.
NOTE: The internal modem does not support the voice functions.
All data and fax functions are supported.
OPERATING BASICS
CAUTIONS: 1. In case of a lightning storm, unplug the modem cable
from the telephone jack.
2. Do not connect the modem to a digital telephone line.
A digital line will damage the modem.
Region selection
Telecommunication regulations vary from one region to another, so you will need to
make sure the internal modem’s settings are correct for the region in which it will be
used.
1. a. In Windows XP, click start, point to All Programs, point to TOSHIBA
Internal Modem and click Region Select Utility.
NOTE: Do not use the Country/Region Select function in the Modem
setup utility in the Control Panel if the function is available. If you
change the Country/Region in the Control Panel, the change may not
take effect.
b. In Windows 2000, click Start, point to Programs, point to TOSHIBA
Internal Modem and click Region Select Utility.
4-10
Using the internal modem
2. The Region Selection icon will appear in the Windows Task Bar.
Figure 4-7 The Region Selection icon (Windows XP)
Figure 4-8 The Region Selection icon (Windows 2000)
3. Click the icon with the primary mouse button to display a list of regions that
the modem supports. A sub menu for telephony location information will also
be displayed. A check will appear next to the currently selected region and
telephony location.
4. Select a region from the region menu or a telephony location from the submenu.
• When you select a telephony location, the corresponding region is automatically selected and it becomes the modem’s current region setting.
Properties menu
Click the icon with the secondary mouse button to display the following menu.
Figure 4-9 The menu list (Windows XP)
4-11
OPERATING BASICS
• When you click a region it becomes the modem’s region selection, and the
New Location for telephony will be set automatically.
User's Manual
Figure 4-10 The menu list (Windows 2000)
Setting
You can enable or disable the following settings:
AutoRun Mode
Region Select Utility starts automatically when you start up the operating
system.
Open the Dialing Properties dialog box after selecting region.
OPERATING BASICS
The dialing properties dialog box will be displayed automatically after you
select the region.
Location list for region selection.
A submenu appears displaying location information for telephony.
Open dialog box, if the modem and Telephony Current
Location region code do not match.
A warning dialog box is displayed if current settings for region code and
telephony location are incorrect.
Modem Selection
If the computer cannot recognize the internal modem, a dialog box is displayed.
Select the COM port for your modem to use.
Dialing Properties
Select this item to display the dialing properties.
4-12
Using the internal modem
CAUTION: If you are using the computer in Japan, technical regulations
described in the Telecommunications Business Law require that you
select Japan region mode. It is illegal to use the modem in Japan with
any other selection.
Connecting
To connect the internal modem cable, follow the steps below.
WARNING: The modular cable that comes with the computer must be
used to connect a modem. Connect the end of the modular cable with the
core to the computer.
CAUTIONS: 1. In case of a lightning storm, unplug the modem cable
from the telephone jack.
2. Do not connect the modem to a digital telephone line.
A digital line will damage the modem.
1. Plug one end of the modular cable into the modem jack.
2. Plug the other end of the modular cable into a telephone jack.
OPERATING BASICS
Figure 4-11 Connecting the internal modem
CAUTION: Do not pull on the cable or move the computer while the
cable is connected.
NOTE: If you use a storage device such as a CD-ROM drive or HDD
connected to a 16-bit PC card, modem speed might be slow or communication might be interrupted.
4-13
User's Manual
Disconnecting
To disconnect the internal modem cable, follow the steps below.
1. Pinch the lever on the connector in the telephone jack and pull out the
connector.
2. Disconnect the cable from the computer in the same manner.
3. In the same way, pull the cable’s other connector out of the computer.
Cleaning the computer
OPERATING BASICS
To help ensure long, trouble-free operation, keep the computer free of dust and use
care with liquids around the computer.
◆
Be careful not to spill liquids into the computer. If the computer does get wet,
turn the power off immediately and let the computer dry completely before you
turn it on again.
◆
Clean the computer using a slightly damp (with water) cloth. You can use glass
cleaner on the display. Spray a small amount of cleaner on a soft, clean cloth
and wipe the screen gently with the cloth.
CAUTION: Never spray cleaner directly onto the computer or let liquid
run into any part of it. Never use harsh or caustic chemical products to
clean the computer.
Moving the computer
The computer is designed for rugged durability. However, a few simple precautions
taken when moving the computer will help ensure trouble-free operation.
◆
Make sure all disk activity has ended before moving the computer. Check the
Disk indicator on the computer and the indicator on any external disk drive.
◆
If a diskette is in the external disk drive, remove it.
◆
Disconnect the AC adaptor and all other peripherals before moving the
computer.
◆
Turn off the power to the computer.
◆
Close the display. Do not pick up the computer by its display panel or back
(where the interface ports are located).
◆
Close all port covers.
◆
Use the carrying case when transporting the computer.
4-14
Heat dispersal
Heat dispersal
To protect from overheating, the CPU has an internal temperature sensor. If the
computer’s internal temperature rises to a certain level, the cooling fan is turned on
or the processing speed is lowered. You can select whether to control the CPU
temperature by turning on the fan first, then if necessary, lowering the CPU speed.
Or, by lowering the CPU speed first, then if necessary, turning on the fan. Use the
Fan item of the Power Save Mode window in TOSHIBA Power Saver.
When the CPU temperature falls to a normal range, the fan is turned off and the CPU
operation returns to standard speed.
NOTE: If the CPU temperature reaches an unacceptably high level with
either setting, the system automatically shuts down to prevent damage.
Data in memory will be lost.
OPERATING BASICS
4-15
OPERATING BASICS
User's Manual
4-16
Chapter 5
The Keyboard
The computer’s keyboard layouts are compatible with a 101/102-key enhanced
keyboard. By pressing some keys in combination, all the 101/102-key keyboard
functions can be executed on the computer.
The number of keys on your keyboard depends on which country/region’s keyboard layout your computer is configured with. Keyboards for numerous languages
are available.
There are five types of keys: typewriter keys, keypad overlay, function keys, soft
keys and cursor control keys.
Typewriter keys
The typewriter keys, produce the upper- and lowercase letters, numbers, punctuation marks, and special symbols that appear on the screen.
There are some differences, however, between using a typewriter and using a
computer keyboard:
Letters and numbers produced in computer text vary in width. Spaces, which
are created by a “space character,” may also vary depending on line justification and other factors.
◆
The lowercase l (el) and the number 1 (one) are not interchangeable on
computers as they are on a typewriter.
◆
The uppercase O (oh) and the 0 (zero) are not interchangeable.
◆
The Caps Lock function key locks only the alphabetic characters in uppercase while the shift lock on a typewriter places all keys in the shifted position.
◆
The Shift keys, the Tab key, and the BkSp (backspace) key perform the
same function as their typewriter counterparts but also have special computer
functions.
5-1
THE KEYBOARD
◆
User's Manual
F1 … F12 function keys
The function keys, not to be confused with Fn, are the 12 keys at the top of your
keyboard. These keys are dark gray, but function differently from the other dark gray
keys.
F1 through F12 are called function keys because they execute programmed
functions when pressed. Used in combination with the Fn key, keys marked with
icons execute specific functions on the computer. See the section, Soft keys: Fn key
combinations, in this chapter. The function executed by individual keys depends on
the software you are using.
Soft keys: Fn key combinations
The Fn (function) is unique to TOSHIBA computers and is used in combination
with other keys to form soft keys. Soft keys are key combinations that enable,
disable or configure specific features.
NOTE: Some software may disable or interfere with soft-key operations.
Soft-key settings are not restored by the Resume feature.
Emulating keys on enhanced keyboard
Esc
F1
~
CapsLock
Shift
#
3
2
Q
Tab
THE KEYBOARD
@
!
1
`
F3
F2
W
A
$
4
E
S
Z
F4
%
5
R
D
X
F5
F
C
Y
G
V
U
I
J
N
F8
(
9
8
H
B
F7
*
&
7
^6
T
F6
)
0
O
K
M
F10
_
-
+
=
{
[
P
>
.
?
/
PrtSc
SysReg
Scroll
lock
Pause
Bk Sp
Ins
Home
PgUp
Num
Lock
End
PgDn
7
Home
8
\
Del
9
PgUp
4
5
6
1
End
2
3
PgDn
F11
F12
}
]
,,
,
:
;
L
<
,
F9
Break
/
*.
+
Enter
Shift
Enter
Ctrl
Alt
Alt
Ctrl
Figure 5-1 A 101-key enhanced keyboard layout
5-2
0
Ins
.
Del
Soft keys: Fn key combinations
The keyboard is designed to provide all the features of the 101-key enhanced
keyboard, shown in figure 5-1. The 101/102-key enhanced keyboard has a numeric
keypad and scroll lock key. It also has additional Enter, Ctrl and Alt keys to the
right of the main keyboard. Since the keyboard is smaller and has fewer keys, some
of the enhanced keyboard functions must be simulated using two keys instead of one
on the larger keyboard.
Your software may require you to use keys that the keyboard does not have.
Pressing the Fn key and one of the following keys simulates the enhanced
keyboard’s functions.
Press Fn + F10 or Fn + F11 to access the integrated keypad. When activated, the
keys with white markings on the bottom edge become numeric keypad keys (Fn +
F11) or cursor control keys (Fn + F10). Refer to the Keypad overlay section in this
chapter for more information on how to operate these keys. The power on default for
both settings is off.
Press Fn + F12 (ScrLock) to lock the cursor on a specific line. The power on
default is off.
Press Fn + Enter to simulate Enter on the enhanced keyboard’s numeric keypad.
THE KEYBOARD
Press Fn + Ctrl to simulate the enhanced keyboard’s right Ctrl key.
Press Fn + Alt to simulate the enhanced keyboard’s right Alt key.
5-3
User's Manual
Hotkeys
Hotkeys (Fn + another key) let you enable or disable certain features of the
computers.
Sound mute: Pressing Fn + Esc in a Windows environment turns sound on or
off. When you press these hotkeys, the current setting will be displayed as an icon.
Volume decrease: Press Fn + 1 to decrease the sound volume. After you press
this hotkey, an icon showing the new setting will be displayed for two seconds.
THE KEYBOARD
Volume increase: Press Fn + 2 to increase the sound volume. After you press
this hotkey, an icon showing the new setting will be displayed for two seconds.
Instant security: Press Fn + F1 to lock the keyboard and blank the screen to
prevent others from accessing your data. To restore the screen and original
settings, press any key or move the AccuPoint II. When a dialog box appears, enter
the screensaver password and click OK. If no password is set, the screen will be
restored when you press any key.
5-4
Soft keys: Fn key combinations
Power save mode: Pressing Fn + F2 changes the power save mode.
If you press Fn + F2, the Power Save Mode is displayed in a dialog box. Continue
holding down Fn and press F2 again to change the setting. You can also change
this setting through the Plugged in or Running on batteries item of the Power
Saver Properties window in Power Saver.
Standby: When you press Fn + F3, the computer can enter Standby. To avoid
entering Standby unexpectedly, a dialog box appears for verification. However, if
you check the checkbox in the dialog box, it will not appear from the next time.
Hibernation: When you press Fn + F4, the computer can enter Hibernation. To
avoid entering Hibernation unexpectedly, a dialog box appears for verification.
However, if you check the checkbox in the dialog box, it will not appear from the next
time.
5-5
THE KEYBOARD
Display selection: Press Fn + F5 to change the active display device. When you
press these hot keys a dialog box appears. Only selectable devices will be displayed.
Hold down Fn and press F5 again to change the device. When you release Fn and
F5, the selected device will change. If you hold down the keys for three seconds the
selection will return to LCD.
User's Manual
Display Brightness: Pressing Fn + F6 decreases the display brightness in
increments. When you press these hotkeys, the current setting will be displayed for
two seconds by an icon. You can also change this setting through the Monitor
brightness item of the Power Save Mode window in Power Saver.
Display Brightness: Pressing Fn + F7 increases the display brightness in
increments. When you press these hotkeys, the current setting will be displayed for
two seconds by a pop-up icon. You can also change this setting through the
Monitor brightness item of the Power Save Mode window in Power Saver.
NOTE: You cannot change the display brightness for about 18 seconds
after the LCD turns on. To protect display quality, the brightness level is
set at the maximum value.
Fn Sticky key
THE KEYBOARD
You can use the TOSHIBA Accessibility Utility to make the Fn key sticky, that is,
you can press it once, release it, and they press an “F number” key.
5-6
Keypad overlay
Windows special keys
The keyboard provides two keys that have special functions in Windows : one
activates the Start menu and the other has the same function as the secondary
mouse button.
This key activates the Windows Start menu.
This key has the same function as the secondary mouse button.
Keypad overlay
Your computer’s keyboard does not have an independent numeric keypad, but its
numeric keypad overlay functions like one.
The keys in the center of the keyboard with white letters make up the numeric
keypad overlay. The overlay provides the same functions as the numeric keypad
on the 101/102-key enhanced keyboard in figure 5-2.
Turning on the overlays
The numeric keypad overlay can be used for numeric data input or cursor and page
control.
Arrow mode
THE KEYBOARD
To turn on the Arrow mode, press Fn + F10. The Arrow mode indicator lights.
Now try cursor and page control using the keys shown in figure 5-2. Press Fn +
F10 again to turn off the overlay.
5-7
User's Manual
Numeric mode
To turn on the Numeric mode, press Fn + F11. The Numeric mode indicator lights.
Now try numeric data entry using the keys in figure 5-2. Press Fn + F11 again to
turn off the overlay.
Figure 5-2 The numeric keypad overlay
THE KEYBOARD
Temporarily using normal keyboard (overlay on)
While using the overlay, you can temporarily access the normal keyboard without
turning off the overlay:
1. Hold Fn and press any other key. All keys will operate as if the overlay were
off.
2. Type uppercase characters by holding Fn + Shift and pressing a character
key.
3. Release Fn to continue using the overlay.
5-8
Generating ASCII characters
Temporarily using overlay (overlay off)
While using the normal keyboard, you can temporarily use the keypad overlay
without turning it on:
1. Press and hold down Fn.
2. Check the keyboard indicators. Pressing Fn turns on the most recently used
overlay. If the Numeric mode indicator lights, you can use the overlay for
numeric entry. If the Arrow mode indicator lights, you can use the overlay for
cursor and page control.
3. Release Fn to return to normal keyboard operation.
Temporarily changing modes
If the computer is in Numeric mode, you can switch temporarily to Arrow
mode by pressing a shift key.
If the computer is in Arrow mode, you can switch temporarily to Numeric
mode by pressing a shift key.
Generating ASCII characters
Not all ASCII characters can be generated using normal keyboard operation. But,
you can generate these characters using their ASCII codes.
With the overlay on:
1. Hold down Alt.
2. Using the overlay keys, type the ASCII code.
3. Release Alt, and the ASCII character appears on the display screen.
With the overlay off:
1. Hold Alt + Fn.
THE KEYBOARD
2. Using the overlay keys, type the ASCII code.
3. Release Alt + Fn, and the ASCII character appears on the display screen.
5-9
THE KEYBOARD
User's Manual
5-10
Power and Power-Up Modes
The computer’s power resources include the AC adaptor and internal batteries. This
chapter gives details on making the most effective use of these resources including
charging and changing batteries, tips for saving battery power, and power up
modes.
Power conditions
The computer’s operating capability and battery charge status are affected by the
power conditions: whether an AC adaptor is connected, whether a battery is
installed and what the charge level is for the battery.
Table 6-1 Power conditions
Power on
Power off (no operation)
Main battery
• Operates
• LED: Main battery green
adaptor
fully
• LED: Main battery green
connected
charged
AC
Main battery
• Quick charge *1
• Operates
1
partially
• Quick charge *
charged
• LED: Main battery orange
or no charge
DC IN green
DC IN green
• LED: Main battery orange
DC IN green
DC IN green
No
• Operates
• No charge
main battery
• No charge
• LED: Main battery off
installed
• LED: Main battery off
DC IN green
DC IN green
6-1
POWER AND
POWER-UP MODES
Chapter 6
POWER AND
POWER-UP MODES
User's Manual
Table 6-1 Power conditions continued
Power on
AC
Power off (no operation)
2nd battery
• Operates
adaptor
fully
• LED: 2nd battery green
connected
charged
2nd battery
• LED: 2nd battery green
• Quick charge *2
• Operates
2
partially
• Quick charge *
charged
• LED: 2nd battery orange
or no charge
• LED: 2nd battery orange
DC IN green
DC IN green
No
• Operates
• No charge
2nd battery
• No charge
• LED: 2nd battery off
installed
• LED: 2nd battery off
DC IN green
AC
Main battery
• Operates
adaptor
charge is
• LED: Main battery off
not
above low
DC IN off
connected
battery
trigger point
Main battery
• Operates
charge is
• LED: Main battery
below low
flashes orange
battery
DC IN off
trigger point
6-2
DC IN green
DC IN green
Main battery
Computer goes
charge is
into resume mode
exhausted
and shuts down *3
No main
• No operation *4
battery
• LED: Main battery off
installed
DC IN off
DC IN green
Power conditions
Power on
AC
2nd battery
• Operates
adaptor
charge
• LED: 2nd battery off
not
is above
Power off (no operation)
DC IN off
connected low battery
trigger point
2nd battery
• Operates
charge
• LED: 2nd battery
is below
flash orange
low battery
DC IN off
trigger point
2nd battery
Computer goes
charge is
into resume mode
exhausted
and shuts down *3
No
• No operation *5
2nd battery
• LED: 2nd battery off
is installed
DC IN off
NOTE: 2nd battery indicator refers to the Secondary battery
indicator when a secondary battery is installed.
*1 When the secondary battery is not charging.
*2 When the main battery is not charging
*3 If a main battery and a secondary battery are installed, the computer does
not enter Resume mode until the charge in both batteries is exhausted.
*4 When no secondary battery is installed
*5 When no main battery is installed
NOTE: When batteries are charged, the main battery is charged first.
When it is fully charged, the secondary battery is charged.
6-3
POWER AND
POWER-UP MODES
Table 6-1 Power conditions continued
POWER AND
POWER-UP MODES
User's Manual
Power indicators
The Main battery, Secondary battery, DC IN and Power indicators on the
system indicator panel alert you to the computer’s operating capability and battery
charge status.
Battery indicators
Check the Main battery indicator to determine the status of the main battery and
the Secondary battery indicator to determine the status of the secondary
battery. The following indicator lights indicate the battery status:
Flashing orange
The battery charge is low. The AC adaptor must be
connected to recharge the battery.
Orange
Indicates the AC adaptor is connected and charging the
battery.
Green
Indicates the AC adaptor is connected and the battery is
fully charged.
No light
Under any other conditions, the indicator does not light.
NOTE: If the battery becomes too hot while it is being charged, the
charge will stop and the battery indicator will go out. When the battery’s
temperature falls to a normal range, charge will resume. This event
occurs regardless of whether the power to the computer is on or off.
DC IN indicator
Check the DC IN indicator to determine the power status with the AC adaptor
connected:
Green
6-4
Indicates the AC adaptor is connected and supplying
proper power to the computer.
Flashing orange
Indicates a problem with the power supply. Plug the AC
adaptor into another outlet. If it still does not operate
properly, see your dealer.
No light
Under any other conditions, the indicator does not light.
Battery types
Check the Power indicator to determine the power status.
Green
Blinking orange
No light
Indicates power is being supplied to the computer and the
computer is turned on.
Indicates the power was turned off while the computer was
in Resume mode. The indicator turns on for one second
and turns off for two seconds.
Under any other conditions, the indicator does not light.
Battery types
The computer has three types of batteries:
◆
Battery Packs – main and secondary (option)
◆
Real Time Clock (RTC) battery
Main battery
When the AC power cord is not connected, the computer’s main power source is a
removable lithium-ion polymer Battery Pack, also referred to in this manual as the
main battery. You can purchase Battery Packs for extended use of the computer
away from an AC power source.
CAUTION: The Battery Pack is a lithium-ion polymer battery, which can
explode if not properly replaced, used, handled or disposed of. Dispose
of the battery as required by local ordinances or regulations. Use only
batteries recommended by TOSHIBA as replacements.
The main battery recharges the RTC batteries. The main battery maintains the state
of the computer when you enable standby mode.
CAUTION: Do not remove the Battery Pack while the computer is in
standby mode. The computer could hang up the next time you turn it on
and data in memory will be lost. The computer could also hang up at
power on if it shut down automatically in standby mode because of a low
battery. In either of the above cases, the standby configuration will not
be saved.
6-5
POWER AND
POWER-UP MODES
Power indicator
POWER AND
POWER-UP MODES
User's Manual
The following message appears when you turn on the power:
WARNING: RESUME FAILURE.
PRESS ANY KEY TO CONTINUE.
If the computer hangs up when you turn it on, perform the following:
Press the power button and hold it down for five seconds, then turn the
power on again.
To ensure that the Battery Pack maintains its maximum capacity, operate the
computer on battery power at least once a month until the Battery Pack is fully
discharged. Refer to Extending battery life in this chapter for procedures. If the
computer is continuously operated on AC power, either through an AC adaptor or a
docking station for an extended period, more than a month, the battery may fail to
retain a charge. It may not function efficiently over the expected life of the battery
and the Battery LED may not indicate a low-battery condition.
Secondary battery (option)
An optional High Capacity 2nd Battery Pack can be increase your battery operating
time. Note the caution on Resume mode in the previous section Main battery.
CAUTION: The secondary Battery Pack is a lithium ion battery, which
can explode if not properly replaced, used, handled or disposed of.
Dispose of the battery as required by local ordinances or regulations.
Use only batteries recommended by TOSHIBA as replacements.
Real time clock battery
The Real Time Clock (RTC) battery provides power for the internal real time clock
and calendar. It also maintains the system configuration.
If the RTC battery becomes completely discharged, the system loses this data and
the real time clock and calendar stop working. The following message appears when
you turn on the power:
*** Bad RTC battery ***
Check system. Then press [F1] key . . . . . .
CAUTION: The computer’s RTC battery is a lithium ion battery and
should be replaced only by your dealer or by a TOSHIBA service
representative. The battery can explode if not properly replaced, used,
handled or disposed of. Dispose of the battery as required by local
ordinances or regulations.
6-6
Care and use of the Battery Pack
The Battery Pack is a vital component of portable computing. Taking proper care of
it will help ensure longer operating time on battery power as well as a longer life for
your Battery Pack. Follow the instructions in this section carefully to ensure safe
operation and maximum performance.
Safety precautions
1. Turn off the computer’s power immediately and disconnect the power cord
from the power socket, if the Battery Pack produces an odor, overheats or
changes color or shape while it is being used or charged. Carefully remove the
Battery Pack from the computer.
2. Be very careful not to short-circuit the Battery Pack. Contacting both terminals
with a metal object can cause injury, fire or damage to the Battery Pack.
3. Do not overcharge, reverse charge, mutilate or disassemble the Battery Pack.
Any one of those actions could release toxic materials, hydrogen and/or
oxygen or other electrolytic substances or cause an increase in the Battery
Pack’s surface temperature.
4. Do not expose the Battery Pack to fire; the Battery Pack could explode.
5. Battery Packs contain toxic substances. Do not dispose of them with ordinary
trash. Dispose of Battery Packs only in accordance with local ordinances.
Always cover the metal terminals with insulating tape to avoid short circuits.
6. If the Battery Pack has leaked or been vented, it should be replaced immediately. Use protective gloves when handling a damaged Battery Pack.
7. When it becomes necessary to replace the Battery Pack, it must be replaced
only by an identical Battery Pack from the same manufacturer.
8. Do not expose the Battery Pack terminals to any metal object other than the
computer contacts. Wrap it or place it in a plastic bag when transporting it.
9. When you install the Battery Pack, you should hear a click when it is seated
properly.
10. Charge the Battery Pack only in the computer or in a Battery Pack charger
designated as an approved option.
11. Reverse polarity should be avoided with all Battery Packs. The Battery Pack is
designed so that it cannot be installed in reverse polarity.
6-7
POWER AND
POWER-UP MODES
Care and use of the Battery Pack
POWER AND
POWER-UP MODES
User's Manual
Charging the batteries
When the power in the Battery Pack becomes low, the Battery indicator flashes
orange indicating that only a few minutes of battery power remain. If you continue
to use the computer while the Battery indicator flashes, the computer enables
Resume mode (so you don’t lose data) and automatically turns off.
You must recharge a Battery Pack when it becomes discharged.
NOTE: The main Battery Pack should be charged only in the computer.
A High Capacity 2nd Battery Pack can be charged either by the computer or by an optional Battery Charger.
Procedures
To recharge a Battery Pack while it is installed in the computer, connect the AC
adaptor to the DC IN socket and plug the other end into a working outlet.
The Battery indicator glows orange when the battery is being charged.
CAUTION: Use only the computer connected to an AC power source or
the optional TOSHIBA Battery charger to charge the Battery Pack. Do
not attempt to charge the Battery Pack with any other charger.
Time
The following table shows the approximate time required to fully charge a discharged battery.
Charging time (hours)
Battery type
Power on
Power off
Main Battery Pack
2.0 to 4.0 or longer
2.0
Secondary Battery Pack
3.0 to 8.0 or longer
3.0
RTC battery
8.0
Doesn’t charge
Battery charging notice
The battery may not charge right away under the following conditions:
◆
The battery is extremely hot or cold. If the battery is extremely hot, it might not
charge at all. Also, to ensure the battery charges to its full capacity, charge the
battery at room temperature of 10° to 30°C (50° to 88°F).
◆
The battery is nearly completely discharged. Leave the AC adaptor connected
for a few minutes and the battery should begin charging.
6-8
Care and use of the Battery Pack
◆
The battery has not been used for a long time.
◆
The battery has completely discharged and been left in the computer for a long
time.
◆
A cool battery is installed in a warm computer.
In such case, follow the steps below.
1. Fully discharge the battery by leaving it in the computer with the power on
until the power automatically shuts off.
2. Plug in the AC adaptor.
3. Charge the battery until the Battery indicator glows green.
Repeat the steps two or three times until the battery recovers normal capacity.
NOTE: Leaving the AC adaptor connected will shorten battery life.
At least once a month, run the computer on battery power until the
battery is fully discharged, then recharge the battery.
Monitoring battery capacity
Remaining battery power can be monitored in the Power Save Modes window in
Power Saver of Windows.
NOTES: 1. Wait at least 16 seconds after turning on the computer before
trying to monitor the remaining operating time. The computer needs this time to check the battery’s remaining
capacity and to calculate the remaining operating time,
based on the current power consumption rate and remaining
battery capacity. The actual remaining operating time may
differ slightly from the calculated time.
2. With repeated discharges and recharges, the battery’s
capacity will gradually decrease. Therefore, an often
used, older battery will not operate for as long as a new
battery even when both are fully charged. In this case,
TOSHIBA Power Saver will indicate a 100% charge for
both the old and new battery, but the displayed estimated
time remaining will be shorter for the older battery.
6-9
POWER AND
POWER-UP MODES
The Battery indicator may show a rapid decrease in battery operating time when
you try to charge a battery under the following conditions:
POWER AND
POWER-UP MODES
User's Manual
Maximizing battery operating time
A battery’s usefulness depends on how long it can supply power on a single
charge.
How long the charge lasts in a battery depends on:
◆
How you configure the computer, for example, whether you enable batterypower saving options. The computer provides a battery save mode to conserve battery power. This mode has the following options:
• Processing speed
• Display auto off
• HDD auto off
• System auto off
• LCD Brightness
◆
How often and how long you use the hard disk and the diskette drive.
◆
How much charge the battery contained to begin with.
◆
How you use optional devices, such as a PC card, to which the battery
supplies power.
◆
Enabling Resume mode conserves battery power if you are frequently turning
the computer off and on.
◆
Where you store your programs and data.
◆
Closing the display when you are not using the keyboard saves power.
◆
Operating time decreases at low temperatures.
◆
The condition of the battery terminals. Make sure the battery terminals stay
clean by wiping them with a clean dry cloth before installing the Battery Pack.
Retaining data with power off
When you turn off your computer with fully charged batteries, the batteries retain
data for the following approximate time periods:
Battery pack (1600 mAh)
RTC battery
6-10
2 days (Resume mode)
25 days (Boot mode)
1 month
Replacing the Battery Pack
POWER AND
POWER-UP MODES
Extending battery life
To maximize the life of your Battery Pack:
◆
At least once a month, disconnect the computer from a power source and
operate it on battery power until the Battery Pack fully discharges. Before
doing so, follow the steps below.
1. Turn off the computer’s power.
2. Disconnect the AC adaptor and turn on the computer’s power. If it does not
turn on go to step 4.
3. Operate the computer on battery power for five minutes. If the Battery Pack
has at least five minutes of operating time, continue operating until the
Battery Pack is fully discharged. If the battery LED flashes or there is some
other warning to indicate a low battery, go to step 4.
4. Connect the AC adaptor to the computer and the power cord to a power
outlet. The DC IN LED should glow green, and the Battery LED should glow
orange to indicate that the Battery Pack is being charged. If the DC IN
indicator does not glow, power is not being supplied. Check the connections
for the AC adaptor and power cord.
5. Charge the Battery Pack until the Battery LED glows green.
◆
If you have extra Battery Packs, rotate their use.
◆
If you will not be using the system for an extended period, more than one
month, remove the Battery Pack.
◆
Disconnect the AC adaptor when the battery is fully charged. Overcharging
makes the battery hot and shortens life.
◆
If you are not going to use the computer for more than eight hours, disconnect
the AC adaptor.
◆
Store spare Battery Packs in a cool dry place out of direct sunlight.
Replacing the Battery Pack
When the Battery Pack reaches the end of its operating life you will need to install a
new one. The life of the Battery Pack is generally about 500 recharges. If the
Battery indicator flashes orange shortly after fully recharging the battery, the
Battery Pack needs to be replaced.
You might also replace a discharged Battery Pack with a charged spare when you
are operating your computer away from an AC power source. This section explains
how to remove and install Battery Packs.
6-11
POWER AND
POWER-UP MODES
User's Manual
Removing the Battery Pack
To replace a discharged Battery Pack, follow the steps below.
CAUTION: When handling Battery Packs, be careful not to short circuit
the terminals. Also do not drop, hit or otherwise apply impact; do not
scratch or break the casing and do not twist or bend the Battery Pack.
1. Save your work.
2. Turn the computer’s power off. Make sure the Power indicator is off.
3. Remove all cables connected to the computer.
4. Turn the computer upside down with the back of the computer facing you.
5. Slide the battery lock to free the Battery Pack for removal.
6. Fit your finger into the indentation next to the Battery Pack and lift it out.
CAUTION: For environmental reasons, do not throw away a spent
Battery Pack. Please return spent Battery Packs to your TOSHIBA
dealer.
BATTERY LOCK
INDENTATION
BATTERY PACK
Figure 6-1 Removing the Battery Pack
6-12
Replacing the Battery Pack
To install a Battery Pack, follow the steps below.
CAUTION: The Battery Pack is a lithium-ion polymer battery, which can
explode if not properly replaced, used, handled or disposed of. Dispose
of the battery as required by local ordinances or regulations. Use only
batteries recommended by TOSHIBA as replacements.
1. Be sure the computer’s power is off and all cables are disconnected.
2. Insert the Battery Pack.
BATTERY PACK
Figure 6-2 Installing the Battery Pack
3. Secure the battery lock.
6-13
POWER AND
POWER-UP MODES
Installing the Battery Pack
POWER AND
POWER-UP MODES
User's Manual
Starting the computer by password
If you registered a password as supervisor or user, you must enter it to start the
computer.
To start up the computer with the password, follow these steps:
1. Turn on the power as described in Chapter 3, Getting Started and the
following message appears:
Password =
2. Enter the password.
3. Press Enter. The computer displays the message below while it starts up.
Valid password entered, system is now starting up.
If you enter the password incorrectly, a buzzer sounds.
NOTE: If you enter the password incorrectly three times in a row, the
computer shuts off. In this case, you must turn the computer back on to
retry password entry.
6-14
Chapter 7
HW Setup and Passwords
HW Setup
TOSHIBA HW Setup lets you configure settings for display, CPU, boot priority,
USB, LAN, general, password and device config.
NOTE: If the supervisor password is set, access to the TOSHIBA HW Setup
program can be prevented when the user password is used to log on to the
computer.
Refer to the Supervisor password readme file for details on enabling/
disabling access to HW Setup. The path to the readme file is
C:\ProgramFiles\TOSHIBA\Windows
Utilities\SVPWTool. In the SVPWTool directory, open the
readme.htm file.
Accessing HW Setup
If you are using Windows XP, click start, click Control Panel, click Printers and
Other Hardware and select TOSHIBA HW Setup to run HW Setup.
If you are using Windows 2000, click Start, point to Settings, click Control
Panel and select TOSHIBA HW Setup to run HW Setup.
7-1
HW SETUP AND
PASSWORDS
This chapter explains how to use TOSHIBA HW Setup program to configure your
computer and how to set passwords.
User's Manual
HW Setup window
HW SETUP AND
PASSWORDS
The HW Setup window contains the following tabs: display, CPU, boot priority,
USB, LAN, general, password, device config.
Figure 7-1 HW setup window (Windows XP)
7-2
HW Setup
HW SETUP AND
PASSWORDS
Figure 7-2 HW setup window (Windows 2000)
There are also three buttons: OK, Cancel and Apply.
OK
Cancel
Apply
Accepts your changes and closes the HW Setup window.
Closes the window without accepting your changes.
Accepts all your changes without closing the HW Setup
window.
7-3
User's Manual
General
This window displays the BIOS version and contains two buttons: Default and
About.
Default Return all HW Setup values to the factory settings.
HW SETUP AND
PASSWORDS
About
Display the HW Setup version..
Setup
This field displays BIOS Version and date.
Password
User Password
This option allows you to set or reset the user password for power on.
Not Registered
Registered
Change or remove the password. (Default)
Set the password. A dialogue box will appear to let you set
the password.
To enter a user password:
1. Select Registered to display the following prompt:
Enter Password:
2. Enter a password of up to 10 characters. The character string you enter is
displayed as a string of asterisks. For example, if you enter a password
consisting of four characters, the display is shown as:
Enter Password: ****
NOTE: If you click the OK button before entering the password, Not
registered will appear on the display.
3. Click the OK button. The following message appears, allowing you to verify
the password.
Verify Password:
7-4
HW Setup
4. If character strings match, the password is registered and the display changes
to:
Registered
If they do not match, the following message appears. You must repeat from
step 1.
Entry Error!!!
HW SETUP AND
PASSWORDS
To delete a user password:
1. Select Not Registered to display the following prompt:
Enter Password:
2. Enter the currently registered password. The character string you enter is
displayed as a string of asterisks.
Enter Password: ****
NOTE: If you click the OK button before entering the password, Registered will appear on the display.
3. Click the OK button. If the character string you enter matches the registered
password, the password option is reset and the display changes to:
Not registered
If they do not match, the following message appears. You must repeat step 1.
Incorrect Password!!!
NOTE: If you enter the password incorrectly three times, the screen will
display:
Sorry, access denied!!! Powering off your
machine then powering it back on again are
required to regain access.
You will not be able to access the password option in the HW Setup. In
this case you must turn the power off and back on to retry the procedure.
4. Follow the same procedures described in the earlier section, How to set the
password, to set a new user password.
Refer to the Supervisor password section later in this chapter for details on setting
the supervisor password.
7-5
User's Manual
Device Config
Device Configuration
HW SETUP AND
PASSWORDS
This option lets you set the device configuration.
All Devices
BIOS sets all devices.
Setup by OS
Operating system sets devices that it can control. (Default)
Display
This tab lets you customize your computer’s display settings for either the internal
LCD screen or for an external monitor.
Power On Display
Lets you set the display to be used when the computer is booted.
Auto-Selected
Selects an external monitor if one is connected. Otherwise, it selects the internal LCD. (Default)
Simultaneous
Selects both the internal LCD and external monitor for
simultaneous display.
CPU
Dynamic CPU Frequency Mode
This option lets you choose from the following settings:
Dynamically Switchable
CPU power consumption and clock speed
automatic switching function is enabled.
When the computer is in use, CPU operation
is automatically switched when necessary.
(Default)
Always High
CPU power consumption and clock speed
automatic switching function is disabled. The
CPU always runs at its fastest speed.
Always Low
CPU power consumption and clock speed
automatic switching function is disabled. The
CPU always runs at low power consumption
and low speed.
7-6
HW Setup
Boot Priority
Boot Priority Options
This option sets the priority for booting the computer. Select from the following
settings:
FDD -> HDD -> CD-ROM -> LAN The computer looks for bootable files in
the following order: diskette drive, HDD,
CD-ROM* and LAN.
HDD -> CD-ROM -> LAN -> FDD The computer looks for bootable files in
the following order: HDD, CD-ROM*, LAN
and diskette drive.
FDD -> CD-ROM -> LAN -> HDD The computer looks for bootable files in
the following order: diskette drive, CDROM*, LAN and HDD.
CD-ROM -> LAN -> HDD -> FDD The computer looks for bootable files in
the following order: CD-ROM*, LAN,
HDD, diskette drive.
CD-ROM -> LAN -> FDD -> HDD The computer looks for bootable files in
the following order: CD-ROM*, LAN,
diskette drive and HDD.
You can override the settings and manually select a boot device by pressing one of
the following keys while the computer is booting:
U
Selects the USB diskette drive.
N
Selects the Network.
1
Selects the primary HDD.
P
Selects the PC card HDD.
C
Selects the CD-ROM*.
This procedure does not affect the settings.
* The CD-ROM is available only with the optional CD-ROM drive.
7-7
HW SETUP AND
PASSWORDS
HDD -> FDD -> CD-ROM -> LAN The computer looks for bootable files in
the following order: HDD, diskette drive,
CD-ROM* and LAN. (Default)
User's Manual
NOTES: 1. PC card HDD boot is supported only by the PC card slot
on the computer. Support is guaranteed only for TOSHIBA
PC card HDDs.
HW SETUP AND
PASSWORDS
2. When you assign a PC card HDD top priority, “PC” is not
displayed. However, the PC card HDD takes the position of
HDD in the Boot Priority Options list above.
Power on Boot Select
When this option is enabled, you can change the boot drive during start up. To
change the boot drive, follow the steps below.
1. Hold down F12 and boot the computer.
2. The following menu will be displayed with the following icons: Built-in HDD,
CD-ROM, FDD, Network (LAN), PCA (ATA) card boot.
NOTE: A bar will appear only under the selected device.
3. Use the left/right cursor keys to highlight the boot device you want and press
Enter.
NOTES: 1. If a supervisor password is set, the menu above does not
appear when you use the user password to start the
computer.
2. The selection method above does not change the boot
priority settings in HW Setup.
3. If you press a key other than one of those above or if the
selected device is not installed, the system will boot according
to the current setting in HW Setup.
USB
USB KB/Mouse Legacy Emulation
Use this option to enable or disable USB KB/Mouse Legacy Emulation. If your
operating system does not support USB, you can still use a USB mouse and
keyboard by setting the USB KB/Mouse Legacy Emulation item to
Enabled.
7-8
Supervisor password
Enabled
Disabled
Enables the USB KB/Mouse Legacy Emulation. (Default)
Disables the USB KB/Mouse Legacy Emulation.
USB-FDD Legacy Emulation
Use this option to enable or disable USB-FDD Legacy Emulation.
Enables the USB-FDD Legacy Emulation. (Default)
Disables the USB-FDD Legacy Emulation.
HW SETUP AND
PASSWORDS
Enabled
Disabled
LAN
Wake-up on LAN
This features lets the computer’s power be turned on when it receives a wake-up
signal from the LAN.
Enabled
Disabled
Enables Wake-up on LAN.
Disables Wake-up on LAN. (Default)
CAUTION: Do not install or remove an optional memory module while
Wake-up on LAN is enabled.
NOTE: Wake-up on LAN does not work without the AC adaptor. Leave it
connected, if you are using this feature.
Built-in LAN
Enabled
Disabled
Enables built-in LAN functions. (Default)
Disables built-in LAN functions.
Supervisor password
Refer to the readme file of the Supervisor Password Utility for instructions on
setting the Supervisor Password.
The path to the readme file is C:\Program Files\TOSHIBA\Windows
Utilities\SVPWTool. In the SVPWTool directory, open the readme.htm
file.
7-9
HW SETUP AND
PASSWORDS
User's Manual
7-10
Chapter 8
Optional Devices
Optional devices can expand the computer’s capabilities and its versatility. The
following optional devices are available from your TOSHIBA dealer:
Cards/memory
PC cards
◆
SD cards
◆
Memory expansion
OPTIONAL DEVICES
◆
Power devices
◆
Battery Pack
◆
High Capacity 2nd Battery Pack
◆
Universal AC Adaptor
◆
Battery Charger
Peripheral devices
◆
USB FDD Kit
◆
Slim Port Replicator
◆
External monitor
Other
◆
Security lock
8-1
User’s Manual
PC cards
The computer is equipped with a PC card expansion slot that can accommodate one
5 mm Type II card. Any PC card that meets industry standards (manufactured by
TOSHIBA or other vendor) can be installed. The slots support 16-bit PC cards,
including PC card 16’s multifunction card and CardBus PC cards.
CardBus supports the new standard of 32-bit PC cards. The bus provides superior
performance for the greater demands of multimedia data transmission.
Installing a PC card
OPTIONAL DEVICES
A PC card slot, on the right side of the computer accommodates one 5 mm PC card
(Type II).
You can install any industry standard PC card such as a SCSI adaptor or flash
memory card.
A dummy card is installed to protect the slot.
Windows allows hot installation of PC cards, which means you can install a card
while the computer’s power is on.
NOTES: 1. Do not install a PC card while the computer is in standby
or hibernation mode. Some cards might not work properly.
2. An HDD or CD-ROM connected to a 16-bit PC card, might
affect the performance of the computer’s sound system and
data transmission, including slower transmission speeds
and dialing errors.
To install the PC card, follow the steps below.
1. A dummy card is installed in the computer when it is shipped. To eject the
dummy, push the eject button and release it to extend the button.
2. Press the extended eject button to pop the card out slightly.
8-2
PC cards
3. Pull the dummy card out and store it in a safe place. Install the dummy card
whenever you remove the PC card.
DUMMY CARD
EJECT BUTTON
4. Insert the PC card. When the card is almost fully seated, you will feel some
resistance. Press gently to ensure a firm connection, but do not force the card
into position.
PC CARD
Figure 8-2 Inserting the PC card
5. Check the configuration in the HW Setup window to make sure it is appropriate for your card.
8-3
OPTIONAL DEVICES
Figure 8-1 Removing the dummy card
User’s Manual
Removing a PC card
To remove the PC card, follow the steps below.
1. Push the eject button and release it to extend the button.
2. Press the extended eject button to pop the card out slightly.
3. Grasp the card and pull it out.
OPTIONAL DEVICES
PC CARD
EJECT BUTTON
Figure 8-3 Removing the PC card
4. Insert the dummy card. Press gently to ensure a firm connection, but do not
force the card into position. Do not leave the PC card slot empty.
DUMMY CARD
Figure 8-4 Inserting the dummy card
8-4
SD cards
SD cards
The computer is equipped with an SD card slot that can accommodate Secure
Digital flash memory cards with capacities of 8 MB, 16 MB, 32 MB, 64 MB and 128
MB. SD cards let you easily transfer data from devices, such as digital cameras and
Personal Digital Assistants, that use SD card flash-memory. The cards have a high
level of security and copy protection features.
The slot cannot accommodate MultiMedia cards.
CAUTION: Keep foreign objects out of the SD card slot. A pin or similar
object can damage the computer’s circuitry.
Installing an SD card
OPTIONAL DEVICES
To install an SD card, follow the steps below.
1. Insert the SD card.
2. Press gently to ensure a firm connection.
SD CARD
Figure 8-5 Inserting an SD card
CAUTION: Make sure the SD card is oriented properly before you insert
it.
8-5
User’s Manual
Removing an SD card
To remove an SD card, follow the steps below.
1. a. In Windows XP, open the Safety Remove Hardware icon on the
system tray and disable the SD card.
b. In Windows 2000, open the Unplug or Eject Hardware icon on the
system tray and disable the SD card.
2. Push in the card and release it to pop the card out slightly.
OPTIONAL DEVICES
3. Grasp the card and remove it.
SD CARD
SD CARD INDICATOR
Figure 8-6 Removing an SD card
CAUTION: Make sure the SD card indicator is out before you remove
the card or turn off the computer’s power. If you remove the card or turn
off the power while the computer is accessing the card you may lose data
or damage the card.
Memory expansion
You can install additional memory in the computer’s memory module to increase the
amount of RAM.
CAUTION: Use only memory modules approved by TOSHIBA.
8-6
Memory expansion
Installing memory module
To install a memory module, make sure the computer is in boot mode then:
1. Turn the computer off in boot mode. Refer to the Turning off the power
section in Chapter 3.
CAUTION: Do not remove the memory module while the computer is in
standby mode. The computer could hang up the next time you turn it on
and data in memory will be lost. In either of the above cases, the standby
configuration will not be saved.
The following message appears when you turn on the power:
WARNING: RESUME FAILURE.
PRESS ANY KEY TO CONTINUE.
2. Remove all cables connected to the computer.
3. Turn the computer upside down and remove the Battery Pack (refer to Chapter
6, Power and Power-Up Modes.)
4. Remove two screws securing the memory module cover.
5. Lift off the cover.
NOTE: Use a point size 0 Phillips screwdriver.
Figure 8-7 Removing the cover
8-7
OPTIONAL DEVICES
If the computer hangs up when you turn it on, perform the following:
Press the power button and hold it down for five seconds, then turn the
power on again.
User’s Manual
6. Align the connector on the memory module with the computer’s connector
and carefully press the module above the connector to ensure a solid connection.
CAUTIONS: 1. Do not touch the connectors on the memory module or
on the computer. Debris on the connectors may cause
memory access problems.
2. Press only the area above the connector. Do not press
on the ICs.
7. Secure it with one screw that came with the memory module.
OPTIONAL DEVICES
CAUTION: Use only the screw that came with the memory module.
Figure 8-8 Inserting the memory module
8. Seat the cover and secure it with two screws.
NOTE: Use a point size 0 Phillips screwdriver.
Figure 8-9 Seating the cover
8-8
Memory expansion
9. When you turn the computer on, it should automatically recognize the total
memory capacity. Use the HW Setup program to verify that the added memory
is recognized. If it is not recognized, check the module’s connection.
NOTE: When you view the memory display, the total amount will be
reduced by 16 MB, which is used for VRAM.
Removing memory module
To remove the memory module, make sure the computer is in boot mode then:
1. Turn the computer off and remove all cables connected to the computer.
OPTIONAL DEVICES
CAUTION: Do not remove the memory module while the computer is in
standby mode. The computer could hang up the next time you turn it on
and data in memory will be lost. In either of the above cases, the standby
configuration will not be saved.
The following message appears when you turn on the power:
WARNING: RESUME FAILURE.
PRESS ANY KEY TO CONTINUE.
If the computer hangs up when you turn it on, perform the following:
Press the power button and hold it down for five seconds, then turn the
power on again.
2. Turn the computer upside down and remove the Battery Pack (refer to Chapter
6, Power and Power-Up Modes.)
3. Remove two screws securing the memory module cover.
4. Lift off the cover.
5. Remove one screw.
6. Fit two slender objects such as tweezers under the memory module on each
side of the connector and pry up to disconnect the module.
8-9
User’s Manual
7. Grasp the memory module by the sides and lift it out.
CAUTION: Do not touch the connectors on the memory module or on the
computer. Debris on the connectors may cause memory access problems.
OPTIONAL DEVICES
Figure 8-10 Removing the memory module
8. Seat the cover and secure it with two screws.
Battery Pack
You can increase the portability of the computer with Battery Packs (PA3154U). If
you’re away from an AC power source, you can replace a low battery with a fully
charged one. See Chapter 6, Power and Power-Up Modes.
High Capacity 2nd Battery Pack
You can install an optional High Capacity 2nd Battery Pack in the computer. A High
Capacity 2nd Battery Pack (PA3155U) is seated in a base that fits beneath the
computer. It provides about twice the power and operating time as the standard
Battery Pack. Refer to the High Capacity 2nd Battery Pack Information Sheet.
Universal AC Adaptor
If you frequently transport the computer between different sites such as your home
and office, purchasing an AC adaptor for each location will reduce the weight and
bulk of your carrying load: PA3153U.
8-10
Slim Port Replicator
Battery Charger
The battery charger (PA3091U) lets you charge a High Capacity 2nd Battery Pack
(PA3155U) outside the computer.
USB FDD Kit
The 3 1/2" external diskette drive module can be connected to the USB port. For
details on connecting the 3 1/2" external diskette drive module, refer to Chapter 4,
Operating Basics.
Slim Port Replicator
CAUTION: The computer must be configured properly before connecting
to a LAN. Logging onto a LAN using the computer’s default settings
could cause a malfunction in LAN operation. Check with your LAN
administrator regarding set-up procedures.
Ports
The following ports and accessories are available on the Slim Port Replicator.
◆
One RJ45 LAN jack
◆
External monitor port
◆
DC IN socket
◆
Universal Serial Bus (four) ports
◆
Port to charge a High Capacity 2nd Battery Pack
8-11
OPTIONAL DEVICES
In addition to the ports available on the computer, the Slim Port Replicator provides,
an external monitor port, four USB ports, a port for charging a High Capacity 2nd
Battery Pack, a LAN jack and a DC-IN socket. The Slim Port Replicator connects
directly to the docking interface on the bottom of the computer. The AC adaptor
connects the Slim Port Replicator to a power source.
User’s Manual
High Capacity 2nd Battery Pack
To charge a High Capacity 2nd Battery Pack, follow the steps below.
1. Connect the computer to the Slim Port Replicator.
2. Connect the dedicated cable to the Slim Port Replicator and to a High Capacity
2nd Battery Pack.
3. Connect an AC Adaptor to the Slim Port Replicator.
NOTES: 1. You cannot use a High Capacity 2nd Battery Pack to
power a Slim Port Replicator.
OPTIONAL DEVICES
2. You must connect the High Capacity 2nd Battery Pack and
an AC adaptor to the Slim Port Replicator to charge the
High Capacity 2nd Battery Pack.
External monitor
An external analog monitor can be connected to the external monitor port on the
computer and Slim Port Replicator. The computer supports VGA and Super VGA
video modes. To connect a monitor, follow the steps below.
CAUTION: If an external monitor is connected to the computer, do not
connect the Slim Port Replicator. First disconnect the external monitor
from the computer then connect the Slim Port Replicator and use its
external monitor port.
NOTE: The Resume feature can be used with an external monitor. Simply
enable Resume and the computer will maintain the data as it is displayed
on the external monitor.
1. Connect the monitor to the external monitor port.
2. Turn the monitor’s power on.
When you turn on the power, the computer automatically recognizes the monitor
and determines whether it is color or monochrome.
You can use the HW Setup to select between Auto-Selected and
Simultaneous displays. Refer to Chapter 7, HW Setup and Passwords.
8-12
Security lock
If you have selected Simultaneous under the Display options of HW Setup,
both the external monitor and the internal LCD will be active when you turn on the
computer. If Auto-Selected is selected, only the external monitor will be active.
To change the display settings, press Fn + F5. If you disconnect the monitor
before you turn the computer off, be sure to press Fn + F5 to switch to the internal
display. Refer to Chapter 5, The Keyboard, for details on using hotkeys to change
the display setting.
NOTE: If you set Simultaneous for the computer’s display, you must
set the computer’s display resolution to the same as that of the external
monitor or other device, such as a projector.
Security lock
Attach one end of a cable to the desk and the other end to the security lock slot on
the left side of the computer.
Figure 8-11 Security lock
8-13
OPTIONAL DEVICES
A security lock enables you to anchor your computer to a desk or other heavy
object to help prevent unauthorized removal of the computer.
OPTIONAL DEVICES
User’s Manual
8-14
Chapter 9
Troubleshooting
TOSHIBA designed the computer for durability. However, should problems occur,
following the procedures in this chapter can help to determine the cause.
All readers should become familiar with this chapter. Knowing what might go
wrong can help prevent problems from occurring.
Problem solving process
Resolving problems will be much easier if you observe the following guidelines:
◆
Stop immediately when you recognize a problem exists. Further action may
result in data loss or damage. You may destroy valuable problem-related
information that can help solve the problem.
◆
Observe what is happening. Write down what the system is doing and what
actions you performed immediately before the problem occurred. If you have a
printer attached, print a copy of the screen using PrtSc.
Preliminary checklist
Consider the simplest solution first. The items in this checklist are easy to fix and
yet can cause what appears to be a serious problem.
◆
Make sure you turn on all peripheral devices before you turn on the computer.
This includes your printer and any other external device you are using.
◆
Before you attach an external device, turn the computer off. When you turn the
computer back on it recognizes the new device.
◆
Make sure all options are set properly in the setup program.
◆
Check all cables. Are they correctly and firmly attached? Loose cables can
cause signal errors.
◆
Inspect all connecting cables for loose wires and all connectors for loose pins.
9-1
TROUBLESHOOTING
The questions and procedures offered in this chapter are meant as a guide, they are
not definitive problem solving techniques. Many problems can be solved simply,
but a few may require help from your dealer. If you find you need to consult your
dealer or others, be prepared to describe the problem in as much detail as possible.
User's Manual
◆
Check that your diskette is correctly inserted and that the diskette’s write
protect tab is correctly set.
Make notes of your observations and keep them in a permanent error log. This will
help you describe your problems to your dealer. If a problem recurs, the log will
help you identify the problem faster.
Analyzing the problem
TROUBLESHOOTING
Sometimes the system gives clues that can help you identify why it is malfunctioning. Keep the following questions in mind:
◆
Which part of the system is not operating properly: keyboard, diskette drives,
hard disk drive, printer, display. Each device produces different symptoms.
◆
Is the operating system configuration set properly? Check the configuration
options.
◆
What appears on the display screen? Does it display any messages or random
characters? Print a copy of the screen if you have a printer attached. Look up
the messages in the software and operating system documentation. Check that
all connecting cables are correctly and firmly attached. Loose cables can cause
erroneous or intermittent signals.
◆
Do any icons light? Which ones? What color are they? Do they stay on or
blink? Write down what you see.
◆
Do you hear any beeps? How many? Are they long or short? Are they high
pitched or low? Is the computer making any unusual noises? Write down what
you hear.
Record your observations so you can describe them to your dealer.
Software
The problems may be caused by your software or diskette.
If you cannot load a software package, the media (usually
a diskette) may be damaged or the program might be
corrupted. Try loading another copy of the software.
If an error message appears while you are using a software
package, check the software documentation. These
documents usually include a problem solving section or a
summary of error messages.
Next, check any error messages in the OS documentation.
9-2
Hardware and system checklist
Hardware
If you cannot find a software problem, check your hardware. First run through the items in the preliminary
checklist above. If you still cannot correct the problem, try
to identify the source. The next section provides checklists
for individual components and peripherals.
Hardware and system checklist
This section discusses problems caused by your computer’s hardware or attached
peripherals. Basic problems may occur in the following areas:
◆ Pointing device
◆ Self test
◆ PC card
◆ Power
◆ SD card
◆ Password
◆ Monitor
◆ Keyboard
◆ Sound system
◆ LCD panel
◆ USB
◆ Hard disk drive
◆ Modem
◆ Diskette drive
◆ LAN
◆ Infrared port
◆ Wireless LAN
TROUBLESHOOTING
◆ System start-up
System start-up
When the computer does not start properly, check the following items:
◆
Self Test
◆
Power Sources
◆
Power-on Password
9-3
User's Manual
Self test
When the computer starts up, the self-test will be run automatically, and the
following will be displayed:
In Touch with Tomorrow
TOSHIBA
This message remains on the screen for a few seconds.
If the self test is successful, the computer tries to load the operating system.
Depending on how the Boot Priority is set in the HW Setup program, the computer
tries to load first from drive A then from drive C, or first from drive C then from drive
A.
If any of the following conditions are present, the self test failed:
◆
The computer stops and does not proceed to display information or messages.
◆
A beep sounds, and after a few seconds no new messages appear.
◆
Random characters appear on the screen, and the system does not function
normally.
◆
The screen displays an error message.
TROUBLESHOOTING
Turn off the computer and check all cable connections. If the test fails again, contact
your dealer.
Power
When the computer is not plugged into an AC adaptor, the Battery Pack is the
primary power source. However, your computer has a number of other power
resources, including intelligent power supply and Real Time Clock battery. These
resources are interrelated and any one could affect apparent power problems. This
section provides check lists for AC adaptor and the main battery. If you cannot
resolve a problem after following them, the cause could lie with another power
resource. In such case, contact your dealer.
9-4
Hardware and system checklist
Overheating power down
If the computer’s internal temperature becomes too high, the computer will automatically enter Hibernation or Resume mode and shut down.
Problem
Procedure
Computer shuts down
and DC IN indicator
blinks orange
Leave the computer off until the DC IN indicator
stops blinking.
NOTE: It is recommended to leave the computer
off until the its interior reaches room temperature
even though the DC IN indicator stops blinking.
If the computer has reached room temperature
and still does not start, or if it starts but shuts
down quickly contact your dealer.
Computer shuts down Indicates a problem with the heat dispersal
and its DC IN indicator system. Please contact your dealer.
is flashing green
If you have trouble turning on the computer with the AC adaptor connected, check
the DC IN indicator. Refer to Chapter 6, Power and Power-Up Modes for more
information.
Problem
Procedure
AC adaptor doesn’t
power the computer
(DC IN indicator does
not glow green)
Check the connections. Make sure the cord is
firmly connected to the computer and a power
outlet.
9-5
TROUBLESHOOTING
AC power
User's Manual
Check the condition of the cord and terminals. If
the cord is frayed or damaged, replace it. If the
terminals are soiled, wipe them with cotton or a
clean cloth.
If the AC adaptor still does not power the computer, contact your dealer.
Battery
TROUBLESHOOTING
If you suspect a problem with the battery, check the DC IN indicator as well as the
Main battery and Secondary battery indicators. For information on indicators
and battery operation see Chapter 6, Power and Power-Up Modes.
Problem
Procedure
Battery doesn’t
power the computer
The battery may be discharged. Connect the AC
adaptor to charge the battery.
Battery doesn’t
charge when the AC
adaptor is attached
(Main battery or
Secondary battery
indicator does not
glow orange.)
If the battery is completely discharged, it will not
begin charging immediately. Wait a few minutes.
If the battery still does not charge, make sure
the outlet is supplying power. Test it by plugging
in an appliance.
Check whether the battery is hot or cold to the
touch. If the battery is too hot or too cold, it will
not charge properly. Let it reach room temperature.
Unplug the AC adaptor and remove the battery to
make sure the terminals are clean. If necessary
wipe them with a soft dry cloth dipped in alcohol.
Connect the AC adaptor and replace the battery.
Make sure it is securely seated.
9-6
Hardware and system checklist
Check the Battery indicator. If it does not glow, let
the computer charge the battery for at least 20
minutes. If the Battery indicator glows after 20
minutes, let the battery continue to charge at least
another 20 minutes before turning on the computer.
If the indicator still does not glow, the battery may
be at the end of its operating life. Replace it.
If you do not think the battery is at the end of its
operating life, see your dealer.
Battery doesn’t
power the computer
as long as expected
If you frequently recharge a partially charged
battery, the battery might not charge to its full
potential. Fully discharge the battery, then try to
charge it again.
Check the power consumption settings in Power
Saver utility. Consider using a power saving
mode.
Problem
Procedure
Cannot enter
password
Refer to the Password section in
Chapter 7, HW Setup and Passwords.
TROUBLESHOOTING
Password
9-7
User's Manual
Keyboard
Keyboard problems can be caused by your setup configuration. For more information refer to Chapter 5, The Keyboard.
Problem
Procedure
Some letter keys
produce numbers
Check that the numeric keypad overlay is not
selected. Press Fn + F10 and try typing again.
Output to screen
is garbled
Make sure the software you are using is not
remapping the keyboard. Remapping involves
reassigning the meaning of each key. See your
software’s documentation.
If you are still unable to use the keyboard,
consult your dealer.
TROUBLESHOOTING
LCD panel
Apparent LCD problems may be related to the computer’s setup. Refer to Chapter
7, HW Setup and Passwords, for more information.
Problem
Procedure
No display
Press hotkeys Fn + F5 to change the display
priority, to make sure it is not set for an external
monitor.
Problems above
remain unresolved
or other problems
occur
Refer to your software’s documentation to
determine if the software is causing the
difficulty.
Run the diagnostic test.
Contact your dealer if the problems continue.
9-8
Hardware and system checklist
Hard disk drive
Problem
Procedure
Computer does not
boot from hard disk
drive
Check if a diskette is in the diskette drive. If a
diskette is inserted, remove it and reboot.
There may be a problem with your operating
system files. Refer to your OS documentation.
Slow performance
Your files may be fragmented. Run SCANDISK
and defragmenter to check the condition of
your files and disk. Refer to your OS documentation or online HELP for information on running
SCANDISK and the defragmenter.
As a last resort, reformat the hard disk. Then,
reload the operating system and other files.
TROUBLESHOOTING
If problems persist, contact your dealer.
9-9
User's Manual
Diskette drive
For more information, refer to Chapter 4, Operaing Basics.
Problem
Procedure
Drive does not
operate
There may be a faulty cable connection. Check
the connection to the computer and to the drive.
Some programs run
correctly but others
do not
The software or hardware configuration may be
causing a problem. Make sure the hardware
configuration matches your software needs.
You cannot access
the external
3 1/2" diskette drive
Try another diskette. If you can access the
diskette, the original diskette (not the drive) is
probably causing the problem.
If problems persist, contact your dealer.
TROUBLESHOOTING
Infrared port
Refer also to the documentation for your IrDA compatible device and related
software.
Problem
Procedure
Infrared devices do
not work as expected
Check that the device is connected to an
electric outlet. Make sure the outlet is supplying
power by plugging in an appliance.
Make sure there is no obstruction blocking
communication between the computer and the
target device.
If problems persist, contact your dealer.
9-10
Hardware and system checklist
Pointing device
If you are using a USB mouse, also refer to the USB section in this chapter and to
your mouse documentation.
Touch Pad
Problem
Procedure
On-screen pointer
does not respond to
Pad operation
The system might be busy. If the pointer is
shaped as an hourglass, wait for it to resume
its normal shape and try again to move it.
Double-tapping
does not work
Try changing the double-click speed setting in
the mouse control utility.
1. Open the Control Panel, select the Mouse
icon and press Enter.
2. Click the Buttons tab.
The mouse pointer
moves too fast or
too slow
Try changing the speed setting in the mouse
control utility.
1. Open the Control Panel, select the Mouse
icon and press Enter.
2. Click the Pointer Options tab.
3. Set the speed as instructed and click OK.
If problems persist, contact your dealer.
9-11
TROUBLESHOOTING
3. Set the double-click speed as instructed and
click OK.
User's Manual
USB mouse
Problem
Procedure
On-screen pointer
does not respond to
cPad operation
The system might be busy. If the pointer is
shaped as an hourglass, wait for it to resume
its normal shape and try again to move it.
Make sure the mouse is properly connected to
the USB port.
Double-tapping
does not work
Try changing the double-click speed setting in
the mouse control utility.
1. Open the Control Panel, select the Mouse
icon and press Enter.
2. Click the Buttons tab.
TROUBLESHOOTING
3. Set the double-click speed as instructed and
click OK.
The mouse pointer
moves too fast or
too slow
Try changing the speed setting in the mouse
control utility.
1. Open the Control Panel, select the Mouse
icon and press Enter.
2. Click the Pointer Options tab.
3. Set the speed as instructed and click OK.
The mouse pointer
moves erractically
The mouse might be dirty. Refer to your mouse
documentations for instructions on cleaning.
If problems persist, contact your dealer.
9-12
Hardware and system checklist
PC card
Refer also to Chapter 8, Optional Devices.
Problem
Procedure
PC card
error occurs
Reseat the PC card to make sure it is firmly
connected.
Make sure the connection between the external
device and the card is firm.
Check the card’s documentation.
If problems persist, contact your dealer.
SD card
Refer also to Chapter 8, Optional Devices.
Procedure
SD card
error occurs
Reseat the SD card to make sure it is firmly
connected.
TROUBLESHOOTING
Problem
Check the card’s documentation.
If problems persist, contact your dealer.
9-13
User's Manual
Monitor
Refer also to Chapter 8, Optional Devices, and to your monitor’s documentation.
Problem
Procedure
Monitor does not
turn on
Make sure that the external monitor’s power
switch is on. Confirm that the external monitor’s
power cable is plugged into a working power
outlet.
No display
Try adjusting the contrast and brightness controls
on the external monitor.
Press hotkeys Fn + F5 to change the display
priority and make sure it is not set for the internal
display.
TROUBLESHOOTING
Display error occurs
Check that the cable connecting the external
monitor to the computer is attached firmly.
If problems persist, contact your dealer.
Sound system
Refer also to documentation for your audio devices.
Problem
Procedure
No sound is heard
Adjust the volume control dial.
Check the software volume settings.
Make sure the headphone connection is secure.
If problems persist, contact your dealer.
9-14
Hardware and system checklist
USB
Refer also to your USB device’s documentation.
Problem
Procedure
USB device does
not work
Check for a firm cable connection between the
USB ports on the computer and the USB device.
Make sure the USB device drivers are properly
installed. Refer to your Windows documentation
for information on checking the drivers.
If you are using an operating system that does
not support USB, you can still use a USB mouse
and/or USB keyboard. If these devices do not
work, make sure the USB KB/Mouse Legacy
Emulation item in HW Setup is set to Enabled.
If problems persist, contact your dealer.
TROUBLESHOOTING
Modem
Refer to the online help files for Appendix C and D.
Problem
Procedure
Communication
software can’t
initialize modem
Make sure the computer’s internal modem
settings are correct. Refer to Modem
Properties in the Control Panel.
You can hear a dial
tone but can’t make
a call
If the call is going through a PBX machine, make
sure the communication application’s tone dial
detection feature is disabled.
You can also use the ATX command. Refer to the
online help files for Appendix C, AT Commands.
9-15
User's Manual
You place a call,
but a connection
can’t be made
Make sure the settings are correct in your
communications application.
After making a call
you can’t hear a ring
Make sure the tone or pulse selection in your
communications application is set correctly.
TROUBLESHOOTING
You can also use the ATD command. Refer to
the online help files for Appendix C, AT Commands.
Communication is
cut off unexpectedly
The computer will automatically cut off
communication when connection with the carrier
is not successful for a set time interval. Try
lengthening this time interval.
A CONNECT display
is quickly replaced by
NO CARRIER
Check the error control setting in your
communications application.
You can also use the AT\N command. Refer to
the online help files for Appendix C, AT Commands.
Character display
becomes garbled
during a
communication
In data transmission, make sure the parity bit
and stop bit settings correspond with those
of the remote computer.
Check the flow control and communication
protocol.
You cannot receive
an incoming call
Check the rings before auto answer setting in
your communications application.
You can also use the ATS0 command. Refer to
the online help files for Appendix D, S-registers.
If problems persist, contact your dealer.
9-16
Hardware and system checklist
LAN
Problem
Procedure
Cannot access LAN
Check for a firm cable connection between the
LAN jack and the LAN HUB.
If problems persist, consult your LAN administrator.
Wireless LAN
If the following procedures do not restore LAN access, consult your LAN administrator. For more information on wireless communication, refer to Chapter 4, Operating Basics.
Problem
Procedure
Cannot access
Wireless LAN
Make sure the computer’s wireless
communication switch is set to on.
9-17
TROUBLESHOOTING
If problems persist, consult your LAN administrator.
User's Manual
TOSHIBA support
If you require any additional help using your computer or if you are having
problems operating the computer, you may need to contact TOSHIBA for additional technical assistance.
Before you call
Some problems you experience may be related to software or the operating system,
it is important to investigate other sources of assistance first. Before contacting
TOSHIBA, try the following:
◆
Review troubleshooting sections in the documentation for software and
peripheral devices.
◆
If a problem occurs when you are running software applications, consult the
software documentation for troubleshooting suggestions. Call the software
company’s technical support for assistance.
◆
Consult the dealer you purchased your computer and/or software from. They
are your best sources for current information and support.
TROUBLESHOOTING
Where to write
If you are still unable to solve the problem and suspect that it is hardware related,
write to TOSHIBA at the nearest location listed on the below.
Outside of Europe
Australia
TOSHIBA Australia Pty. Ltd.
Information Systems Division
84-92 Talavera Road
North Ryde N.S.W. 2113
Sydney
Canada
TOSHIBA of Canada Ltd.
191 McNabb Street,
Markham, Ontario
L3R8H2
9-18
Singapore
TOSHIBA Singapore Pte. Ltd.
438B Alexandra Road #06-01
Alexandra Technopark
Singapore 119968
United States of America
TOSHIBA America Information
Systems, Inc.
9740 Irvine Boulevard
Irvine, California 92618
USA
TOSHIBA support
The Rest of Europe
TOSHIBA Europe (I.E.) GmbH
Geschäftsbereich,
Deutschland-Österreich
Hammfelddamm8,
D-41460 Neuss, Germany
TROUBLESHOOTING
InEurope
Germany & Austria
TOSHIBA Europe (I.E.) GmbH
Geschäftsbereich,
Deutschland-Österreich
Hammfelddamm8,
D-41460 Neuss, Germany
France
TOSHIBA Systèms France S.A.
7, Rue Ampère B.P. 131,
92804 Puteaux Cedex
Netherlands
TOSHIBA Information Systems,
Benelux B.V.
Rivium Boulevard
41 2909 LK Capelle a/d IJssel
Spain
TOSHIBA Information Systems,
ESPAÑA
Parque Empresarial San Fernando
Edificio Europa, la Planta,
Escalera A 28830 Madrid
UnitedKingdom
TOSHIBA Information Systems (U.K.)
Ltd.
TOSHIBA Court
Weybridge Business Park
Addlestone Road
Weybridge, Surrey KT15 2UL
9-19
TROUBLESHOOTING
User's Manual
9-20
Specifications
This appendix summarizes the computer’s technical specifications.
Physical Dimensions
Size
With TFT display
289 (w) x 229 (d) x 14.9/19.1 (h) millimeters (does not include
the thicker part of the bottom of the computer)
Weight
Hard disk
Memory
20GB
256 MB
Display
Kilograms
12" XGA-TFT 1.19 kg typical*
* Weight will vary depending on whether the computer has Wireless LAN
capability.
Environmental Requirements
Conditions
Operating
Nonoperating
Thermal Gradient
Wet-bulb temperature
Conditions
Operating
Nonoperating
Ambient
temperature
Relative
humidity
5°C (41°F) to 35°C (95°F)
20% to 80%
-20°C (-4°F) to 65°C (149°F)
10% to 90%
20°C per hour maximum
26°Cmaximum
Altitude (from sea level)
-60 to 3,000 meters
-60 to 10,000 meters maximum
Power Requirements
AC adaptor
100- 240 volts AC
50 or 60 hertz (cycles per second)
A-1
APPENDIX A
Appendix A
APPENDIX A
User's Manual
Computer
15VDC
3.0 amperes
Built-in Modem
Network control unit (NCU)
Type of NCU
Type of line
Type of dialing
AA
Telephone line (analog only)
Pulse
Tone
Control command
AT commands
EIA-578 commands
Monitor function
Computer’s speaker
Communication specifications
Communication
system
Data:
Fax:
Communication
protocol
Data
ITU-T-Rec
(Former CCITT)
Bell
Fax
ITU-T-Rec
(Former CCITT)
V.21/V.22/V.22bis/V.32
/V.32bis/V.34/V.90
103/212A
V.17/V.29/V.27ter
/V.21 ch2
Communication
speed
Data transmission and reception
300/1200/2400/4800/7200/9600/12000/14400/
16800/19200/21600/24000/26400/28800/31200/
33600 bps
Data reception only with V.90
28000/29333/30666/32000/33333/34666/36000/
37333/38666/40000/41333/42666/44000/45333/
46666/48000/49333/50666/52000/53333/54666/56000
bps
Fax
2400/4800/7200/9600/12000/14400 bps
Error correcting
MNP class 4 and ITU-T V.42
Data compression
A-2
Full duplex
Half duplex
MNP class 5 and ITU-T V.42bis
Appendix B
Display Controller and
Modes
APPENDIX B
Display controller
The display controller interprets software commands into hardware commands that
turn particular pels on or off.
The controller is an advanced Video Graphics Array (VGA) that provides Super
VGA (SVGA) and Extended Graphics Array (XGA) support for the internal LCD
and external monitors. The displays up to 1024 x 768 (XGA). The controller also
supports simultaneous display on the internal LCD and on an external monitor.
A high-resolution external monitor connected to the computer can display up to
1600 horizontal and 1200 vertical pixels and up to 64K colors.
The display controller also controls the video mode, which uses industry standard
rules to govern the screen resolution and the maximum number of colors that can be
displayed on screen.
Software written for a given video mode will run on any computer that supports the
mode.
The computer’s display controller supports all VGA and SVGA modes, the most
widely used industry standards.
B-1
User's Manual
Video modes
The computer supports video modes defined in the table below. If your application
offers a selection of mode numbers that do not match the numbers on the table,
select a mode based on mode type, resolution, character matrix, number of colors
and refresh rates. Also, consider the following points:
APPENDIX B
◆
◆
◆
If your software supports both graphics and text modes, the screen display
may appear to operate faster using a text mode.
The LCD’s highest graphics resolution is 1024 horizontal x 768 vertical lines.
If a resolution greater than the display’s physical capacity is selected, the
display driver renders a virtual display.
Table Video modes
Video
mode
Type
Resolution
Character
matrix
(pels)
LCD
colors
CRT
colors
Scanning
frequency
Vertical
0, 1
VGA
Text
40 x 25
Characters
8x8
16 of 256K
16 of 256K
70Hz
2, 3
VGA
Text
80 x 25
Characters
8x8
16 of 256K
16 of 256K
70Hz
0*, 1*
VGA
Text
40 x 25
Characters
8 x 14
16 of 256K
16 of 256K
70Hz
2*, 3*
VGA
Text
80 x 25
Characters
8 x 14
16 of 256K
16 of 256K
70Hz
0+, 1+
VGA
Text
40 x 25
Characters
8(9) x 16
16 of 256K
16 of 256K
70Hz
2+, 3+
VGA
Text
80 x 25
Characters
8(9) x 16
16 of 256K
16 of 256K
70Hz
4, 5
VGA
Grph
320 x 200
Pels
8x8
4 of 256K
4 of 256K
70Hz
6
VGA
Grph
640 x 200
Pels
8x8
2 of 256K
2 of 256K
70Hz
7
VGA
Text
VGA
Text
80 x 25
Characters
80 x 25
Characters
8(9) x 14
Mono
Mono
70Hz
8(9) x 16
Mono
Mono
70Hz
7+
B-2
Appendix B
Table Video modes continued
Type
Resolution
Character
matrix
(pels)
LCD
colors
CRT
colors
Scanning
frequency
Vertical
D
VGA
Grph
320 x 200
Pels
8x8
16 of 256K
16 of 256K
70Hz
E
VGA
Grph
640 x 200
Pels
8x8
16 of 256K
16 of 256K
70Hz
F
VGA
Grph
640 x 350
Pels
8 x 14
Mono
Mono
70Hz
10
VGA
Grph
640 x 350
Pels
8 x 14
16 of 256K
16 of 256K
70Hz
11
VGA
Grph
VGA
Grph
640 x 480
Pels
640 x 480
Pels
8 x 16
2 of 256K
2 of 256K
60Hz
8 x 16
16 of 256K
16 of 256K
60Hz
VGA
Grph
320 x 200
Pels
8x8
256 of 256K 256 of 256K
70Hz
SVGA 640 x 480
Grph Pels
256 of 256K 256 of 256K
60Hz
75Hz
85Hz
SVGA 800 x 600
Grph Pels
256 of 256K 256 of 256K
60Hz
75Hz
85Hz
SVGA 1024 x 768
Grph Pels
256 of 256K 256 of 256K 60Hz
75Hz
85Hz
SVGA 1280 x 1024
Grph Pels
256 of 256K 256 of 256K
60Hz
75Hz
85Hz
SVGA 1600 x 1200
Grph Pels
256 of 256K 256 of 256K
60Hz
12
13
APPENDIX B
Video
mode
B-3
User's Manual
Table Video modes continued
APPENDIX B
Video
mode
B-4
Type
Resolution
Character
matrix
(pels)
LCD
colors
CRT
colors
Scanning
frequency
Vertical
SVGA 640 x 480
Grph Pels
64K of 64K 64K of 64K
60Hz
75Hz
85Hz
SVGA 800 x 600
Grph Pels
64K of 64K 64K of 64K
60Hz
75Hz
85Hz
SVGA 1024 x 768
Grph Pels
64K of 64K 64K of 64K
60Hz
75Hz
85Hz
SVGA 1280 x 1024
Grph Pels
64K of 64K 64K of 64K
60Hz
75Hz
85Hz
SVGA 1600 x 1200
Grph Pels
64K of 64K 64K of 64K
60Hz
SVGA 640 x 480
Grph Pels
16M of 16M 16M of 16M 60Hz
75Hz
85Hz
SVGA 800 x 600
Grph Pels
16M of 16M 16M of 16M 60Hz
75Hz
85Hz
SVGA 1024 x 768
Grph Pels
16M of 16M 16M of 16M 60Hz
75Hz
Appendix C
AT Commands
In most cases, you will not need to type AT commands manually. However,
there might be some occasions when you will need to do so.
This chapter describes AT commands for data mode. Fax and voice commands
are taken care of by application software.
The format for entering AT commands is:
ATXn
Any command issued is acknowledged with a response in either text or numeric
values known as result codes.
All commands and command-values accepted by the modem are described in
this section; any entry other than those listed results in an error.
+++
Escape sequence
The escape sequence allows the modem to exit data mode and enter
on-line command mode. While in on-line command mode, you can
communicate directly to your modem using AT commands. Once you
finish, you can return to data mode using the ATO command.
A pause, the length of which is set by Escape Guard Time (S12), must
be completed after an escape sequence is entered, This pause prevents
the modem from interpreting the escape sequence as data.
The value of the escape sequence character may be changed using
register S2.
A/
Repeat last command
This command repeats the last command string entered. Do not
precede this command with an AT prefix or conclude it by pressing
Enter.
C-1
APPENDIX C
where X is the AT command, and n is the specific value for that command. After
you type in the command press Enter.
User's Manual
A
Answer command
This command instructs the modem to go off-hook and answer an
incoming call.
Bn
Communication standard setting
This command determines the communication standard CCITT or Bell.
B0
Selects CCITT V.22 mode when the modem is at 1200 bps.
B1
Selects Bell 212A when the modem is at 1200 bps (default).
B15
Selects V.21 when the modem is at 300 bps.
B16
Selects Bell 103J when the modem is at 300 bps (default).
Result Codes:
OK
n=0,1,15,16
APPENDIX C
ERROR Otherwise
Dn
Dial
This command instructs the modem to dial a telephone number. Enter n
(the telephone number and any modifiers) after the ATD command.
Any digit or symbol (0-9, *, #, A, B, C, D) may be dialed as touch-tone
digits. Characters such as spaces, hyphens, and parentheses do not
count. They are ignored by the modem, but you may want to include
them to make the number and modifiers easier to read.
The following may be used as phone number modifiers:
C-2
P
Pulse dialing.
T
Touch-tone dialing (default).
,
Pause during dialing. Pause for time specified in Register S8
before processing the next character in the dial string.
W
Wait for dial tone. Modem waits for a second dial tone before
processing the dial string.
@
Wait for quiet answer. Wait for five seconds of silence after
dialing the number. If silence is not detected, the modem
sends a NO ANSWER result code back to the caller.
!
Hook flash. Causes the modem to go on-hook for 0.5 seconds
and then return to off-hook.
Appendix C
En
;
Return to command mode. Causes the modem to return to
command mode after dialing a number, without disconnecting
the call.
S=n
Dial a telephone number previously stored using the &Zn=X
command (See &Zn=X command for more information). The
range is 0-3.
Echo command
This command controls whether or not the characters entered from
your computer keyboard are displayed on your monitor (echoed) while
the modem is in command mode.
E0
Disables echo to the computer.
E1
Enables echo to the computer (default).
Result Codes:
APPENDIX C
OK
n=0,1
ERROR Otherwise
Hn
Hook control
This command instructs the modem to go on-hook to disconnect a call,
or off-hook to make the phone line busy.
H0
Modem goes on-hook (default).
H1
Modem goes off-hook.
Result Codes:
OK
n=0,1
ERROR Otherwise
In
Request ID information
This command displays product information about the modem.
I0
Returns modem identity string and driver version number.
I3
Same as I0.
I9
Returns region ID in English.
Result Codes:
OK
n=0,3,9
ERROR Otherwise
C-3
User's Manual
Ln
Monitor speaker volume
This command sets speaker volume to low, medium, or high.
L0
Low volume.
L1
Low volume. (Same as L0)
L2
Medium volume (default).
L3
High volume.
Result Codes:
OK
n=0,1,2,3
ERROR Otherwise
Mn
Monitor speaker mode
APPENDIX C
This command turns the speaker on or off.
M0
The speaker is off.
M1
The speaker is on until the modem detects the carrier signal
(default).
M2
The speaker is always on when modem is off-hook.
M3
Speaker is on until the carrier is detected, except when dialing.
Result Codes:
OK
n=0,1,2,3
ERROR Otherwise
Nn
Modulation handshake
This command controls whether or not the local modem performs a
negotiated handshake at connection time with the remote modem when
the communication speed of the two modems is different.
N0
When originating or answering, this is for handshake only at
the communication standard specified by S37 and the ATB
command.
N1
When originating or answering, begin the handshake at the
communication standard specified by S37 and the ATB
command (default).
During handshake, a lower transmission speed may be
selected.
C-4
Appendix C
Result Codes:
OK
n=0,1
ERROR Otherwise
On
Return on-line to data mode
O0
Instructs the modem to exit on-line command mode and return
to data mode (see AT escape sequence, +++).
O1
This command issues a retrain before returning to on-line data
mode.
O3
This command issues a rate renegotiation before returning to
on-line data mode.
Result Codes:
OK
n=0,1,3
P
Select pulse dialing
This command configures the modem for pulse (non touch-tone)
dialing. Dialed digits are pulsed until a T command or dial modifier is
received. Tone dial is the default setting.
Qn
Result code control
Result codes are informational messages sent from the modem and
displayed on your monitor. Basic result codes are OK, CONNECT,
RING, NO CARRIER, and ERROR. The ATQ command allows the
user to turn result codes on or off.
Q0
Enables modem to send result codes to the computer (default).
Q1
Disables modem from sending result codes to the computer.
Result Codes:
OK
n=0,1
ERROR Otherwise
C-5
APPENDIX C
ERROR Otherwise
User's Manual
T
Select tone dialing
This command instructs the modem to send DTMF tones while dialing.
Dialed digits are tone dialed until a P command or dial modifier is
received. This is the default setting.
Vn
DCE response format
This command controls whether result codes (including call progress
and negotiation progress messages) are displayed as words or their
numeric equivalents.
V0
Displays result codes as digits.
V1
Displays result codes as text (default).
Result Codes:
APPENDIX C
OK
n=0,1
ERROR Otherwise
Xn
Result code selection, call progress monitoring
This command selects which result codes will be used by the modem.
Command
X0
Dial tone
Busy signal
Supported Result
detect
detect
Code
Disable
Disable
OK, CONNECT, RING, NO CARRIER,
ERROR
X1
Disable
Disable
OK, RING, NO CARRIER, ERROR,
CONNECT <RATE>
X2
Enable
Disable
OK, RING, NO CARRIER, ERROR,
NODIALTONE, CONNECT <RATE>
X3
Disable
Enable
OK, RING, NO CARRIER, ERROR,
BUSY, CONNECT <RATE>,
BLACKLISTED
X4 (default) Enable
Enable
OK, RING, NO CARRIER, ERROR,
NODIALTONE, BUSY, CONNECT
<RATE>, DELAYED, BLACKLISTED,
REORDER, WARBLE, CALL WAITING
DETECTED
C-6
Appendix C
X5
Enable
Enable
OK, RING, NO CARRIER, ERROR,
NODIALTONE, BUSY, CONNECT
<RATE>, RRING, NO BONGTONE,
DELAYED, BLACKLISTED, REORDER,
WARBLE, CALL WAITING DETECTED
Dial tone detect
Disabled: The modem dials a call regardless of whether it detects a
dial tone.
Enabled:
The modem dials only upon detection of a dial tone, and
disconnects the call if the dial tone is not detected within
10 seconds.
APPENDIX C
Busy tone detect
Disabled: The modem ignores any busy tones it receives.
Enabled:
The modem monitors for busy tones.
Result Codes:
OK
n=0,1,2,3,4,5
ERROR Otherwise
Zn
Recall stored profile
The modem performs a soft reset and restores (recalls) the configuration profile according to the parameter supplied. If no parameter is
specified, zero is assumed. Either Z0 or Z1 restores the profile.
Result Codes:
OK
n=0,1
ERROR Otherwise
&Cn Data Carrier Detect (DCD) control
Data Carrier Detect is a signal from the modem to the computer
indicating that a carrier signal is being received from a remote modem.
DCD normally turns off when the modem no longer detects the carrier
signal.
C-7
User's Manual
&C0
The state of the carrier from the remote modem is ignored.
DCD circuit is always on.
&C1
DCD turns on when the remote modem’s carrier signal is
detected, and off when the carrier signal is not detected
(default).
Result Codes:
OK
n=0,1
ERROR Otherwise
&Dn DTR control
APPENDIX C
This command interprets how the modem responds to the state of the
DTR signal and changes to the DTR signal.
&D0
Ignore. The modem ignores the true status of DTR and treats
it as always on. This should only be used if your communication software does not provide DTR to the modem
&D1
If the DTR signal is not detected while in on-line data mode,
the modem enters command mode, issues an OK result code,
and remains connected.
&D2
If the DTR signal is not detected while in on-line data mode,
the modem disconnects (default).
&D3
Reset on the on-to-off DTR transition.
Result Codes:
OK
n=0,1,2,3
ERROR Otherwise
&F
Load factory settings
This command loads the configuration stored and programmed at the
factory. This operation replaces all of the command options and the Sregister settings in the active configuration with factory values.
&F
C-8
Recall factory setting as active configuration.
Appendix C
&Gn V.22bis guard tone control
This command determines which guard tone, if any, to transmit while
transmitting in the high band (answer mode). This command is only
used in V.22 and V.22bis mode. This option is not used in North
America and is for international use only.
&G0
Guard tone disabled (default).
&G1
Sets guard tone to 550 Hz.
&G2
Sets guard tone to 1800 Hz.
Result Codes:
OK
n=0,1,2
ERROR Otherwise
&Kn Local flow control selection
Disable flow control.
&K3
Enable CTS/RTS flow control (default).
&K4
Enable XON/XOFF flow control.
APPENDIX C
&K0
Result Codes:
OK
n=0,3,4
ERROR Otherwise
&Pn Select Pulse Dial Make/Break Ratio (WW)
&P0
Selects 39% - 61% make/break ratio at 10 pulses per second.
&P1
Selects 33% - 67% make/break ratio at 10 pulses per second.
&P2
Selects 33% - 67% make/break ratio at 20 pulses per second.
Result Codes:
OK
n=0,1,2
ERROR Otherwise
&Tn
Self-test commands
These tests can help to isolate problems if you experience periodic
data loss or random errors.
C-9
User's Manual
&T0
Abort. Stops any test in progress.
&T1
Local analog loop. This test verifies modem operation, as well
as the connection between the modem and computer. Any
data entered at the local DTE is modulated, then demodulated,
and returned to the local DTE. To work properly, the modem
must be off-line.
Result Codes:
APPENDIX C
&V
OK
n=0
CONNECT
n=1
ERROR
Otherwise
Display Current Configuration
This command displays the current configuration of the modem. If
nonvolatile memory is supported the stored profiles are displayed
as well.
&V
&W
View profiles.
Store current configuration
Saves the current (active) configuration (profile), including S-Registers.
The current configuration comprises a list of storable parameters
illustrated in the &V command. These settings are restored to the
active configuration upon receiving a Zn command or at power up.
Refer to the &V command.
&W
&Zn=x
Stores the current configuration.
Store telephone number
This command is used to store up to four dialing strings in the
modem’s nonvolatile memory for later dialing. The format for the
command is &Zn=“stored number” where n is the location 0-3 to which
the number should be written. The dial string may contain up to 34
characters. The ATDS=n command dials using the string stored in
location n.
Result codes:
OK
n=0, 1, 2, 3
ERROR Otherwise
C-10
Appendix C
\Nn
Error control mode selection
This command determines the type of error control used by the modem
when sending or receiving data.
\N0
Buffer mode. No error control.
\N1
Direct mode.
\N2
MNP or disconnect mode. The modem attempts to connect
using MNP2-4 error control procedures. If this fails, the
modem disconnects.
This is also known as MNP reliable mode.
\N3
V.42, MNP, or buffered (default).
\N4
V.42 or disconnect. The modem attempts to connect in V.42
error control mode. If this fails, the modem disconnects.
\N5
V.42. MNP or buffered (same as \N3).
\N7
V.42. MNP or buffered (same as \N3).
Result Codes:
OK
n=0,1,2,3,4,5,7
ERROR Otherwise
\Qn
Local flow control selection
\Q0
Disable flow control.
\Q1
XON/XOFF software flow control.
\Q3
CTS/RTS to DTE (default).
Result Codes:
OK
n=0,1,3
ERROR Otherwise
C-11
APPENDIX C
The modem attempts to connect in V.42 error control mode. If
this fails, it attempts to connect in MNP mode. If this fails, it
connects in buffer mode and continues operation. This is also
known as V.42/MNP auto reliable mode (same as &Q5).
User's Manual
\Vn
Protocol result code
\V0
Disable protocol result code appended to DCE speed.
\V1
Enable protocol result code appended to DCE speed (default).
Result Codes:
OK
n=0,1
ERROR Otherwise
%B
View numbers in blacklist
APPENDIX C
If blacklisting is in effect, this command displays the numbers for
which the last call attempted in the past two hours failed. The ERROR
result code appears in regions that do not require blacklisting.
%Cn Data compression control
This command determines the operation of V.42bis and MNP class 5
data compression. On-line changes do not take effect until a disconnect occurs first.
%C0
V.42bis/MNP 5 disabled. No data compression.
%C3
V.42bis/MNP 5 enabled. Data compression enabled (default).
Result Codes:
OK
n=0,3
ERROR Otherwise
C-12
Appendix D
S-registers
S-registers contain the settings that determine how a number of functions of the
internal modem operate. For example, how many times to let the telephone ring
before the modem answers and how long to wait before it hangs up if a connection fails. You can also customize certain AT commands such as the escape
sequence and command line termination.
The contents of the registers are changed automatically when you modify
corresponding settings in your communication software. If you choose,
however, you can display and edit the contents of the registers manually when
the modem is in command mode. If the value is out of the acceptable range, then
an error is generated.
This chapter describes the settings for each S-register.
S-register values
The format for displaying the value of an S-register is:
APPENDIX D
ATSn?
where n is the register number. After you type in the register press Enter.
The format for modifying the value of an S-register is:
ATSn=r
where n is the register number, and r is the new register value. After you type in
the register and its new value press Enter.
NOTE: Some registers vary from one country/region to another.
D-1
User's Manual
S0
Auto answer ring number
This register determines the number of rings the modem will count
before automatically answering a call. Enter 0 (zero) if you do not want
the modem to automatically answer at all. When disabled, the modem
can only answer with an ATA command.
Range: 0-255
Default: 0
Units:
S1
rings
Ring counter
This register is read only. The value of S1 is incremented with each
ring. If no ring occurs over a six-second interval, this register is
cleared.
Range: 0-225
Default: 0
Units:
S2
rings
AT escape character (user defined)
APPENDIX D
This register determines the ASCII values used for an escape sequence. The default is the + character. The escape sequence allows the
modem to exit data mode and enter command mode when on-line.
Values greater than 127 disable the escape sequence.
Range: 0-255, ASCII decimal
Default: 43
Units:
S3
ASCII
Command line termination character
(user defined)
This register determines the ASCII values as the carriage return
character. This character is used to end command lines and result
codes.
Range: 0-127, ASCII decimal
Default: 13 (carriage return)
Units:
D-2
ASCII
Appendix D
S4
Response formatting character (user defined)
This register determines the ASCII value used as the line feed character. The modem uses a line feed character in command mode when it
responds to the computer.
Range: 0-127, ASCII decimal
Default: 10 (line feed)
Units:
S5
ASCII
Command line editing character (user defined)
This register sets the character recognized as a backspace and pertains
to asynchronous only. The modem will not recognize the backspace
character if it is set to a value that is greater than 32 ASCII. This
character can be used to edit a command line. When the echo command is enabled, the modem echoes back to the local DTE the backspace character, an ASCII space character, and a second backspace
character. This means a total of three characters are transmitted each
time the modem processes the backspace character.
Range: 0-127, ASCII decimal
Default: 8 (backspace)
Units:
Wait before dialing
This register sets the length of time, in seconds, that the modem must
wait (pause) after going off-hook before dialing the first digit of the
telephone number. The modem always pauses for a minimum of two
seconds, even if the value of S6 is less that two seconds. The wait for
dial tone call progress feature (W dial modifier in the dial string) will
override the value in register S6. This operation, however, may be
affected by some ATX options according to country/region restrictions. In some countries/regions, S6 will set dial tone detect time.
Range: 3-255
Default: 3
Units:
seconds
D-3
APPENDIX D
S6
ASCII
User's Manual
S7
Connection completion time-out
This register sets the time, in seconds, that the modem must wait
before hanging up because carrier is not detected. The timer is started
when the modem finishes dialing (originate), or goes off-hook (answer). In originate mode, the timer is reset upon detection of an answer
tone if allowed by county restriction. The timer also specifies the wait
for silence time for the @ dial modifier in seconds. S7 is not associated
with the W dial modifier.
Range: 1-255
Default: 50
Units:
S8
seconds
Comma pause time
This register sets the time, in seconds, that the modem must pause
when it encounters a comma (,) in the dial command string. In some
countries/regions, S8 will set both wait before dialing and comma
pause time.
Range: 0-255
Default: 2
APPENDIX D
Units:
S11
seconds
DTMF dialing speed
This register determines the dialing speed which is prefixed for each
country/region.
Range: 50-255
Default: 95
Units:
S12
.001 seconds
Escape guard time
This register sets the value (in 20 millisecond increments) for the
required pause after the escape sequence.
Range: 0-255
Default: 50
Units:
D-4
.02 seconds
Appendix D
S37
Dial line rate
maximum modem speed
S37 = 1
reserved
S37 = 2
1200/75 bps
S37 = 3
300 bps
S37 = 4
reserved
S37 = 5
1200 bps
S37 = 6
2400 bps
S37 = 7
4800 bps
S37 = 8
7200 bps
S37 = 9
9600 bps
S37 = 10
12000 bps
S37 = 11
14400 bps
S37 = 12
16800 bps
S37 = 13
19200 bps
S37 = 14
21600 bps
S37 = 15
24000 bps
S37 = 16
26400 bps
S37 = 17
28800 bps
S37 = 18
31200 bps
S37 = 19
33600 bps
APPENDIX D
S37 = 0 (default)
D-5
User's Manual
AT command set result codes
The following table shows the result codes.
The result code summary
APPENDIX D
Result Code
Numeric
Description
OK
0
Command executed
CONNECT
1
Modem connected to line
RING
2
A ring signal has been detected
NO CARRIER
3
Modem lost carrier signal, or does
not detect carrier signal, or does
not detect answer tone
ERROR
4
Invalid command
CONNECT 1200 EC*1
5
Connection at 1200 bps
NO DIAL TONE
6
No dial tone detected
BUSY
7
Busy signal detected
NO ANSWER
8
No quiet answer
CONNECT 2400 EC*1
10
Connection at 2400 bps
CONNECT 4800 EC*1
11
Connection at 4800 bps
CONNECT 9600 EC*1
12
Connection at 9600 bps
CONNECT 14400 EC*1
13
Connection at 14400 bps
CONNECT 19200 EC*1
14
Connection at 19200 bps
CONNECT 7200 EC*1
24
Connection at 7200 bps
CONNECT 12000 EC*1
25
Connection at 12000 bps
CONNECT 16800 EC*1
86
Connection at 16800 bps
CONNECT 300 EC*1
40
Connection at 300 bps
CONNECT 21600 EC*1
55
Connection at 21600 bps
CONNECT 24000 EC*1
56
Connection at 24000 bps
CONNECT 26400 EC*1
57
Connection at 26400 bps
CONNECT 28800 EC*1
58
Connection at 28800 bps
CONNECT 31200 EC*1
59
Connection at 31200 bps
CONNECT 33600 EC*1
60
Connection at 33600 bps
D-6
Appendix D
Result Code
Numeric
Description
DELAYED*2
88
Delay is in effect for the dialed
number
BLACKLISTED*2
89
Dialed number is blacklisted
BLACKLIST FULL*2
90
Blacklist is full
*1: EC only appears when the Extended Result Codes configuration option is
enabled. EC is replaced by one of the following symbols, depending upon
the error control method used:
V.42bis - V.42 error control and V.42bis data compression.
V.42 - V.42 error control only.
MNP 5 - MNP class 4 error control and MNP class 5 data compression.
MNP 4 - MNP class 4 error control only.
NoEC - No error control protocol.
*2: In some countries/regions, these result codes may not appear.
APPENDIX D
D-7
APPENDIX D
User's Manual
D-8
Appendix E
V.90
The TOSHIBA internal modem uses V.90 technology. The modem is capable of
downstream speeds of 56Kbps (kilobits per second) when connected to an Internet
service provider that supports V.90. As with any modem, the actual throughput
(speed of data transfer) depends on analog telephone line conditions, which can
vary considerably. Therefore, many users will experience throughput in the range of
32-44Kbps under normal telephone line conditions. Upstream data flows at the V.34
rate.
NOTE: V.90 rates can be achieved only when one V.90 capable modem
is connected to another. The TOSHIBA Internal modem will select
automatically V.34 if the remote modem lacks V.90 capability or if a
combination of network and/or phone line conditions prevent V.90
connection.
V.90 mode
Function
Transmission speed
Data V.90
From 56K (maximum) to 28Kbps (minimum)
Reception only
APPENDIX E
E-1
User's Manual
Table E-1 Result codes for a V.90 connection
No. Result code
Description
70
CONNECT 32000 EC* Connection at 32000 bits/s
72
CONNECT 36000 EC* Connection at 36000 bits/s
74
CONNECT 40000 EC* Connection at 40000 bits/s
76
CONNECT 44000 EC* Connection at 44000 bits/s
78
CONNECT 48000 EC* Connection at 48000 bits/s
80
CONNECT 52000 EC* Connection at 52000 bits/s
82
CONNECT 56000 EC* Connection at 56000 bits/s
100 CONNECT 28000 EC* Connection at 28000 bits/s
101 CONNECT 29333 EC* Connection at 29333 bits/s
102 CONNECT 30666 EC* Connection at 30666 bits/s
103 CONNECT 33333 EC* Connection at 33333 bits/s
104 CONNECT 34666 EC* Connection at 34666 bits/s
105 CONNECT 37333 EC* Connection at 37333 bits/s
106 CONNECT 38666 EC* Connection at 38666 bits/s
107 CONNECT 41333 EC* Connection at 41333 bits/s
108 CONNECT 42666 EC* Connection at 42666 bits/s
109 CONNECT 45333 EC* Connection at 45333 bits/s
110 CONNECT 46666 EC* Connection at 46666 bits/s
111 CONNECT 49333 EC* Connection at 49333 bits/s
112 CONNECT 50666 EC* Connection at 50666 bits/s
113 CONNECT 53333 EC* Connection at 53333 bits/s
APPENDIX E
114 CONNECT 54666 EC* Connection at 54666 bits/s
*EC stands for the Error Control method, which appears only when the extended
result codes configuration option is enabled. EC is replaced by one of the
following symbols, depending on the error control method used.
V42bis
V42
NoEC
E-2
V.42 error control and V.42bis data compression
V.42 error control only
No error control protocol
Appendix E
AT Command
-V90=* V.90 Dial Line Rate
-V90 sets the maximum V.90 downstream that the modem attempts to
connect.
-V90=0 V.90 disabled
-V90=1 V.90 enabled: automatic speed selection - maximum modem speed
(default)
APPENDIX E
E-3
APPENDIX E
User's Manual
E-4
Appendix F
Wireless LAN
This document is intended to help you get your Wireless LAN network up and
running, with a minimum of parameters.
About TOSHIBA Wireless solution
The Wireless LAN card Kit enables you to:
◆
Connect your computer to a peer-to-peer workgroup of Wireless computing
devices.
◆
Connect your computer to a Local Area Network (LAN) Infrastructure that
includes Wireless LAN Access Points, or other IEEE802.11 compliant LAN
systems.
◆
Expand the capabilities of your Wireless LAN Access Points, to support
Wireless devices that have been equipped with Wireless LAN card.
NOTE: The internal Wireless LAN card can’t be used with the TOSHIBA
Wireless LAN PC card.
F-1
APPENDIX F
User’s Manual
Peer-to-peer workgroup
The peer-to-peer workgroup configuration enables you to quickly set up a small
Wireless workgroup, where the workgroup participants can exchange files using
features such as Files and Printer Sharing as supported by Microsoft Networking.
Figure F-1 Peer-to-peer Wireless workgroup
You can use this option to set up a temporary or ad-hoc network in environment
where no access points are available, for example in Small Office/Home Office
(SOHO) environments.
As long as the stations are within range of one another, this is the easiest and least
expensive way to set up a Wireless network.
F-2
Appendix F
APPENDIX F
Enterprise networking
Figure F-2 Stand-alone Wireless LAN
With the Wireless LAN Access Points you can connect to a corporate Local Area
Network (LAN) infrastructure to have Wireless access to all network facilities.
LAN Infrastructures may either be.
◆
Stand-alone Wireless LANs as pictured in Figure F-2
F-3
APPENDIX F
User’s Manual
◆
Wireless network infrastructures connected to an existing Ethernet network as
pictured in Figure F-3.
Figure F-3 LAN Infrastructure
Easy configuration
The Wireless LAN card functions like any standard wired Ethernet card except it
gives you the freedom of Wireless connections.
Where an Ethernet card requires a cable connection to a hub and/or patch panel, the
cable physically limits the location of the wired connection.
Expanding or re-designing your network is easy. A Wireless LAN allows you
connect your computer to a Local Area Network (LAN) from anywhere within the
Wireless coverage area.
NOTE: The Wireless LAN card is a radio product. Refer to the flyer
Information to the User for regulatory information that may apply in your
country/region.
Wireless LAN card features
The TOSHIBA Wireless LAN mini-PCI card is a Wireless network card that fits into
a mini-PCI Type IIIA slot.
F-4
Appendix F
The Wireless LAN card is a Wireless network card that complies with the IEEE
802.11 standard on Wireless LANs (Revision B). The Wireless LAN card supports
data rates up to 11 Mbit/s.
◆
Wi-Fi (Wireless Fidelity) certified by the Wireless
Ethernet Compatibility Alliance (WECA). This means
that your Wireless hardware will communicate with
other vendors’ IEEE 802.11 compliant Wireless LAN
products.
◆
Fully compatible with any other Wireless LAN system based on Direct
Sequence Spread Spectrum (DSSS) radio technology that complies with the
IEEE 802.11 standard on Wireless LANs (Revision B).
Wireless LAN cards
The Wireless LAN card supports the following Wireless LAN features:
◆
Automatic Transmit Rate Select mechanism in the transmit range of 11, 5.5, 2
and 1 Mbit/s.
◆
Frequency Channel Selection (2.4 GHz).
◆
Roaming over multiple channels.
◆
Card Power Management.
◆
Wired Equivalent Privacy (WEP) data encryption, based on the 128 bit RC4
encryption algorithm.
Basic settings for enterprise networks
NOTE: For Windows XP, refer to the operating system help files for
procedures on connecting to an Enterprise Network.
If you wish to connect to an Enterprise Network, use the Add/Edit Configuration
Profile window to:
1. Click the Start button from the Windows task bar.
2. Click Settings, and then Control Panel.
3. In the Control Panel window, double-click the Wireless Network icon.
4. Select to connect to an Access Point.
F-5
APPENDIX F
Wireless LAN card types
APPENDIX F
User’s Manual
5. Set the correct Network Name.
Figure F-4 Edit Configuration window
6. In the field Network Name, define the name of the Wireless network to
which you want to connect. You can either use:
• The value ANY
To connect to any Wireless LAN network in the vicinity of your computer.
• An exact value to connect to a specific network.
Consult your LAN administrator for the value that applies to your network.
The Network Name can be any alphanumeric string in the range of “a” to
“z”, “A” to “Z” and “0” to “9” with a maximum of 32 characters.
7. Click OK to confirm and return to the Add/Edit Configuration Profile
window.
8. Click OK again to finish.
F-6
Appendix F
APPENDIX F
Basic settings for peer-to-peer workgroups
NOTE: For Windows XP, refer to the operating system help files for
procedures on connecting to an Enterprise Network.
If you wish to connect to a peer-to-peer workgroup, use the Add/Edit Configuration
Profile window to:
1. Click the Start button from the Windows task bar.
2. Click on Settings, and then on Control Panel.
3. In the Control Panel window, double-click the Wireless Network icon.
4. Select to connect to a peer-to-peer workgroup.
5. Set the correct Network Name and Encryption Key.
Figure F-5 Edit Configuration window : peer-to-peer
6. In the field Network Name, define the name of the Wireless network to
which you want to connect.
The Network Name can be any alphanumeric string in the range of “a” to “z,”
“A” to “Z” and “0” to “9” with a maximum of 32 characters (case-sensitive).
F-7
User’s Manual
APPENDIX F
• If there is already a peer-to-peer group with this name available, your
computer will automatically connect to this workgroup.
• If there is not yet such a group available, your computer will automatically
start one with this name.
7. Click OK to confirm and return to the Add/Edit Configuration
Profile window.
8. Click OK again to finish.
Working with Wireless and Windows
This chapter provides general information about:
◆
Using your Wireless LAN card
◆
Using the Client Manager
◆
View Wireless link quality
◆
View/modify Wireless LAN card settings
Using your Wireless LAN card
Radio antennas
The radio and antennas of your Wireless LAN card perform best in an open
environment with as few obstacles as possible.
To achieve the maximum range for Wireless communications, do not cover the top
panel and with objects such as books or thick stacks of paper.
View other computers
When multiple Wireless LAN stations are up-and-running in your Wireless
network, you can use the procedure described below to display the other computers
on the network:
1. Start Windows Explorer.
2. Scroll down the list of files and folders to find the item Network Neighborhood.
3. Double-click the Network Neighborhood item to display all stations in
your Microsoft Networking Group.
4. To display other workgroups in the network environment, double-click the
Entire Network icon.
F-8
Appendix F
◆
Powered up and logged onto the network.
◆
Configured to operate with identical Microsoft Network settings concerning:
• Networking Protocol
• Wireless Network Name
• Workgroup Name
To view or modify the Station Name or Workgroup of your computer,
proceed as follows:
1. Click Start on the Windows task bar.
2. Click Settings, and then click Control Panel.
3. In the Control Panel window, double-click the Network icon.
4. In the Network Settings window, select the Identification tab.
You can verify and change the Station Name or Workgroup parameters.
NOTE: You have to restart your computer before changes to the Network
Settings will be effected.
To verify the radio connection with other stations refer to View Wireless Link
Quality.
Using the Client Manager
If you installed the Wireless LAN Client Manager you can use the Client Manager
to:
◆
Verify the quality of your Wireless connection to the network.
◆
View/Modify the configuration settings of your Wireless LAN card.
The Client Manager icon is displayed in the System Tray on your
Windows task bar at the right-side on the bottom of your screen, indicating
that the Client Manager programs is running.
◆
Click the icon once with your left mouse button to retrieve a more detailed
status overview.
◆
Click the icon once with your right mouse button to display a menu with more
options.
F-9
APPENDIX F
If you cannot find other Wireless LAN networked computers, verify whether the
other Wireless LAN computers are:
APPENDIX F
User’s Manual
View Wireless link quality
You can use Client Manager icon on the Windows task bar to verify the link quality
of your network connection.
An overview of all possible icons is given in Table1. When the Client Manager icon
is not indicating excellent or good radio connection, act as described in Table F-1.
Table F-1 Client Manager Icon
Icon
F-10
Description
Color
Excellent radio connection
Green
Good radio connection
Green
Marginal radio connection:
The radio signal is weak. Move closer to
the Wireless LAN Access Point.
Yellow
Poor radio connection:
The radio signal is very weak. Save your
files and move closer to the Wireless LAN
Access Point.
Red
No radio connection because:
• Looking for initial connection, or
• You have moved out of range of the
network.
Red
Peer-to Peer network connection
Blank
Appendix F
If you would like to view or modify Wireless LAN parameters, for example because
you would like to connect to another network or type of network, proceed as
follows:
1. Right-click on the Client Manager icon on the Windows task bar.
2. From the menu, select Configuration Profile, see Figure F-6, and select:
• Add/Edit Profile to add a new profile or to modify an existing profile.
• One of the existing profiles (if present) to select a profile without
viewing or modifying the settings.
After you selecting another profile, the card will use the new profile to connect to
the Wireless network.
Figure F-6 Edit Wireless Configuration Settings
If your Client Manager icon is not visible, you have to start the Client Manager program again:
1. Click Start from the Windows task bar.
2. Select Programs, and then select the TOSHIBA Wireless Solution
workgroup.
3. Next select Client Manager to start the Client Manager program.
Alternatively you can to change the card configuration via the Control Panel:
1. Click Start from the Windows task bar.
2. Click Settings, and then click Control Panel.
3. In the Control Panel window, double-click the Wireless Network icon.
4. If you select new parameters, click,
• the OK button to confirm your changes, or
• the Cancel button to ignore them.
F-11
APPENDIX F
View/modify Wireless LAN card settings
APPENDIX F
User’s Manual
Advanced configurations
NOTE: For Windows XP, refer to the operating system help files for
procedures on connecting to an Enterprise Network.
Although your Wireless LAN card will work fine in most network environments
with the Basic Parameters, you may wish to explore the advanced parameters
options as displayed in the Wireless LAN card’s Edit Configuration
window. You can set advanced parameters only if your computer is connected to an
existing network. Consult your LAN administrator for details.
Encryption window
The encryption tab enables you to define the encryption keys that your Wireless
LAN card should use to:
◆
Decrypt Wireless messages received via its Wireless interface.
◆
Encrypt data that will be transmitted via the Wireless interface.
CAUTION: Encryption needs to be the same for all Wireless LAN
stations.
Figure F-7 Encryption window
F-12
Appendix F
Advanced window
Use this window to set advanced parameters.
Figure F-8 Advanced window
Card Power Management
Interference Robustness
RTS/CTS Medium
To extend the battery life of (mobile) Wireless
devices.
Can be activated in exceptional cases when troubleshooting slow performance of a Wireless LAN
network that could be related to in-band interference
from devices such as microwave ovens.
This parameter can be activated:
• If the density of Wireless LAN stations and access
points is very low
• As a result of poor network performance due to
excessive frame collisions at the access points
F-13
APPENDIX F
You can identify up to four different key values to decrypt Wireless data, and select
one of these keys to encrypt Wireless data transmissions.
APPENDIX F
User’s Manual
Admin window
You can set the following parameters in the Admin window.
Figure F-9 Admin parameters
Distance between
access points
Depending on the number of access points in a Wireless
LAN network this parameter controls the network performance.
MAC address
Can be activated in exceptional cases when troubleshooting slow performance of the Wireless LAN network that
could be related to in-band interference from devices such
as microwave ovens.
F-14
Appendix F
APPENDIX F
Card specifications
Table F-2 Physical specifications
Form Factor
Mini-PCI TypeIIIA
Dimensions
Weight
Temperature and Humidity
Operation
0 to 55 C
Maximum humidity 95%
Transit
-20 to 70 C
15 to 95% (no condensation)
Storage
-10 to 60 C
10 to 90% (no condensation)
Although the card may still operate in the range of –20 to 70 C, operation outside
the range of 0 to 55 C may no longer be according to specifications.
Table F-3 Power Characteristic
Doze Mode
45mA
Receive Mode
250mA
Transmit Mode
350mA
Power Supply
3.3V
F-15
APPENDIX F
User’s Manual
Table F-4 Networking Characteristics
Compatibility
n IEEE 802.11 Standard for Wireless LANS (DSSS)
n Wi-Fi (Wireless Fidelity) certified by the Wireless
Ethernet Compatibility Alliance (WECA)
Network
Operating
System
n Microsoft Windows® Networking
Host
Operating
System
Microsoft Windows® NT v4.0:
n NDIS4 Miniport Driver
Microsoft Windows® 98/Me/2000
n NDIS5 Miniport Driver
Microsoft Windows® XP
n NDIS5.1 Miniport Driver
Media Access
CSMA/CA (Collision Avoidance) with
Protocol
Data Rate
Acknowledgment (ACK)
n High
11 Mb/s
n Medium 5.5 Mb/s
n Standard 2 Mb/s
n Low
1 Mb/s
The cards use an automatic Transmit Rate Select
mechanism.
Radio characteristics
Radio characteristics of Wireless LAN cards may vary according to:
◆
Country/region where the product was purchased
◆
Type of product
Wireless communication is often subject to local radio regulations. Although
Wireless LAN networking products have been designed for operation in the licensefree 2.4 GHz band, local radio regulations may impose limitations on the use of
Wireless communication equipment.
NOTE: Refer to the flyer Information to the User for regulatory information that may apply in your country/region.
F-16
Appendix F
R-F Frequency Band
2.4GHz (2400-2483.5 MHz)
Modulation Technique
Direct Sequence Spread Spectrum
n CCK for High & Medium Transmit Rate
n DQPSK for Standard Transmit Rate
n DBPSK for Low Transmit Rate
Spreading
11-chip Barker Sequence
Bit Error Rate (BER)
Better than 10-5
Nominal Output Power
15 dBm
Transmit Rate
High
Speed
11 Mb/s
Medium
Speed
5.5 Mb/s
Standard Low
Speed
Speed
2 Mb/s
1Mb/s
Receiver Sensitivity
-83 dBm
-87 dBm
-91 dBm
-94 dBm
Delay Spread
(at FER of <1%)
65 ns
225 ns
400 ns
500 ns
The range of the Wireless signal is related to the Transmit Rate of the Wireless
communication. Communications at lower Transmit range may travel longer
distances.
NOTE: The range values listed in Table F-5 are typical distances as
measured at the TOSHIBA Wireless LAN laboratories. These values
provide rule-of-thumb guides. They may vary according to the actual
radio conditions at the location where the Wireless LAN product is
installed.
◆
The range of your Wireless devices can be affected when the antennas are
placed near metal surfaces and solid high-density materials.
◆
Range is also affected by obstacles in the signal path of the radio that may
either absorb or reflect the radio signal.
Table F-5 lists the typical ranges when used indoors in office environments such as
the following:
◆
In Open Office environments, where antennas can see each other, i.e. there are
no physical obstructions between them.
◆
In Semi-open Office environments, where work space is divided by shoulderheight, hollow wall elements; antennas are at desktop level.
F-17
APPENDIX F
Table F-5 Radio characteristics
APPENDIX F
User’s Manual
◆
In Closed Office environments, work space is separated by floor-to-ceiling
solid walls.
Supported frequency sub-bands
Subject to the radio regulations that apply in your country/region, your Wireless
LAN card may support a different set of 2.4 GHz channels (see Table F-6).
Consult your Authorized Wireless LAN or TOSHIBA Sales office for information
about the radio regulations that apply in your country/region.
Table F-6 Wireless IEEE 802.11 Channels Sets
Frequency Range
Channel ID
1
2
3
4
5
6
7
8
9
10
11
2400-2483.5 MHz
2412
2417
2422
2427
2432
2437
2442
2447
2452
2457*
2462
* Factory-set default channels
When installing Wireless LAN cards, the channel configuration is managed as
follows:
◆
For Wireless clients that operate in a Wireless LAN Infrastructure, the Wireless LAN card will automatically start operation at the channel identified by the
Wireless LAN Access Point. When roaming between different access points
the station can dynamically switch to another channel if required.
◆
For Wireless LAN cards installed in Wireless clients operating in a peer-to-peer
mode, the card will use the default channel 10.
◆
In a Wireless LAN Access Point, the Wireless LAN card will use the factoryset default channel (printed in bold), unless the LAN Administrator selected a
different channel when configuring the Wireless LAN Access Point device.
F-18
Appendix G
AC Power Cord and
Connectors
Length:
Minimum 2 meters
Wire size:
Minimum 0.75 mm2
Current rating:
Minimum 2.5 amperes
Voltage rating:
125 or 250 VAC
(depending on country/region’s power standards)
Certification agencies
U.S. and Canada: UL listed and CSA certified
No. 18 AWG, Type SVT or SPT-2 two conductor
Europe:
Austria:
OVE
Italy:
IMQ
Belgium:
CEBEC
The Netherlands:
KEMA
Denmark:
DEMKO
Norway:
NEMKO
Finland:
SETI
Sweden:
SEMKO
France:
UTE
Switzerland:
SEV
Germany:
VDE
United Kingdom:
BSI
Australia:
AS
Japan:
DENANHO
In Europe, power cords must be VDE type, H05VVH2-F and two conductor.
For the United States and Canada, plug configuration must be a 2-15P (250 V) or 115P (125 V) as designated in the U.S. National Electrical code handbook and the
Canadian Electrical Code Part II.
G-1
APPENDIX G
The power cord’s AC input plug must be compatible with the various international
AC power outlets and the cord must meet the standards for the country/region in
which it is used. All cords must meet the following specifications:
User's Manual
The following illustrations show the plug shapes for the U.S.A. and Canada, the
United Kingdom, Australia and Europe.
United Kingdom
APPENDIX G
USA and Canada
UL approved
CSA approved
Australia
AS approved
G-2
BS approved
Europe
Approved by the
appropriate agency
Appendix H
Internal Modem Guide
This appendix describes how to install and the remove the internal modem.
CAUTIONS: 1. Do not remove the base cover except to remove or
install the internal modem or to check the PTT label.
2. Do not disassemble the computer beyond the steps
described in this instruction or touch any components
not specifically described.
4. Be careful not to drop any screws or other foreign
matter into the computer. Metal or other foreign matter
can damage the computer.
Installing the internal modem
NOTE: The internal modem is preinstalled. The following is for information only.
To install the modem board, follow the steps below.
1. Save your data, quit Windows and turn off the power.
2. Disconnect the AC Adaptor and any other peripheral devices.
3. Turn the computer upside down and remove the Battery Pack.
4. Remove two screws securing the HDD pack cover and remove the HDD pack.
5. Remove fifteen screws (one screw has a rubber cover). Do not remove the
screws securing the memory module.
6. Remove the bottom cover.
7. Connect the modem cable.
8. Install the modem and secure it with two screws.
9. Seat the bottom cover and secure fifteen screws.
H-1
APPENDIX H
3. Always remove the Battery Pack and disconnect the AC
Adaptor before removing the base cover.
User’s Manual
10. Insert the HDD pack into the slot.
11. Secure the HDD pack cover with two screws.
12. Install the Battery Pack.
Removing the internal modem
To remove the internal modem.
1. Save your data, quit Windows and turn off the power.
2. Disconnect the AC Adaptor and any other peripheral devices.
3. Turn the computer upside down and remove the Battery Pack.
4. Remove two screws securing the HDD pack cover and remove the HDD pack.
APPENDIX H
5. Remove fifteen screws (one screw has a rubber cover). Do not remove the
screws securing the memory module.
6. Remove the bottom cover. You can check the PPT label at this point.
7. Remove two screws securing the modem and remove it.
8. Disconnect the modem cable.
9. Secure fifteen screws.
10. Insert the HDD pack into the slot.
11. Secure the HDD pack cover with two screws.
12. Install the Battery Pack.
The internal modem is approved by Japan Approvals Institute for Telecommunications Equipment.
A00-0940JP
H-2
Appendix I
Parts Numbers
The computer configuration and parts numbers, printed on a label on the bottom of
the computer, indicate the CPU, LCD, memory, HDD and communication devices.
APPENDIX I
I-1
APPENDIX I
The following table shows the computer configuration indicated on a label. Shaded areas indicate abbreviations used on the label.
The explanations are to the left of the shading. Abbreviations are not limited to those in this chart. They may change without
notice.
CPU
750* P750
LCD
12"TFT-XGA
Memory
12TX
256MB
256M
HDD
20G
Communication
20
Modem/LAN
M/L
Modem/LAN/Wireless LAN
M/L/WL
* Figures indicate the CPU operating speed in megahertz. For example, P750 means Ultra Low Voltage Mobile Intel®
Pentium® III processor 750 MHz-M .
User's Manual
I-2
Configurations
The terms in this glossary cover the topics discussed in this manual. Alternate
naming is included for reference.
Abbreviations
IrDA: Infrared Data Association
IRQ: interrupt request
AC: alternating current
KB: kilobyte
ANSI: American National Standards
Institute
LCD: liquid crystal display
APM: advanced power manager
LED: light emitting diode
LSI: large scale integration
ASCII: American Standard Code for
Information Interchange
MDA: monochrome display adaptor
BIOS: basic input output system
MS-DOS: Microsoft Disk Operating
System
CMOS: complementary metal-oxide
semiconductor
CPU: central processing unit
CRT: cathode ray tube
OCR: optical character recognition
(reader)
PCB: printed circuit board
DAA: Data Access Arrangement
PCI: peripheral component interconnect
DC: direct current
RAM: random access memory
DDC: display data channel
RGB: red, green, and blue
DMA: direct memory access
ROM: read only memory
DOS: disk operating system
RTC: real time clock.
DVI: Digital Visual Interface
ECP: extended capabilities port
SCSI: small computer system
interface
EGA: enhanced graphics adaptor
SIO: serial input/output
FDD: floppy disk drive
SVGA: super video graphics adaptor
FIR: fast infrared
TFT: thin-film transistor
HDD: hard disk drive
IDE: integrated drive electronics
UART: universal asynchronous
receiver/transmitter
I/O: input/output
USB: Universal Serial Bus
Glossary-1
GLOSSARY
Glossary
GLOSSARY
adaptor
(Abbreviations continued)
VESA: Video Electronic Standards
Association
VGA: video graphics array
VRT: voltage reduction technology
A
adaptor: A device that provides an
interface between two dissimilar
electronic devices. For example, the
AC adaptor modifies the power from a
wall outlet for use by the computer.
This term also refers to the add-in
circuit cards that control external
devices, such as video monitors and
magnetic tape devices.
allocate: To assign a space or
function for a specific task.
alphanumeric: Keyboard characters
including letters, numbers and other
symbols, such as punctuation marks or
mathematical symbols.
alternating current (AC): Electric
current that reverses its direction of
flow at regular intervals.
analog signal: A signal whose
characteristics such as amplitude and
frequency vary in proportion to (are
an analog of) the value to be transmitted. Voice communications are analog
signals.
Glossary-2
ANSI: American National Standards
Institute. An organization established
to adopt and define standards for a
variety of technical disciplines. For
example, ANSI defined the ASCII
standard and other information
processing requirements.
antistatic: A material used to prevent
the buildup of static electricity.
application: A group of programs
that together are used for a specific
task such as accounting, financial
planning, spreadsheets, word processing, and games, etc.
ASCII: American Standard Code for
Information Interchange. ASCII code
is a set of 256 binary codes that
represent the most commonly used
letters, numbers, and symbols.
async: Short for asynchronous.
asynchronous: Lacking regular time
relationship. As applied to computer
communications, asynchronous refers
to the method of transmitting data that
does not require a steady stream of bits
to be transmitted at regular time
intervals.
AUTOEXEC.BAT: A batch file that
executes a series of MS-DOS commands and programs each time you
start the computer.
cache memory
backup: A duplicate copy of files kept
as a spare in case the original is
destroyed.
batch file: A file that can be executed
from the system prompt containing a
sequence of operating system commands or executable files. See also
AUTOEXEC.BAT.
binary: The base two number system
composed of zeros and ones (off or
on), used by most digital computers.
The right most digit of a binary
number has a value of 1, the next a
value of 2, then 4, 8, 16, and so on.
For example, the binary number 101
has a value of 5. See also ASCII.
BIOS: Basic Input Output System.
The firmware that controls data flow
within the computer. See also firmware.
bit: Derived from “binary digit,” the
basic unit of information used by the
computer. It is either zero or one.
Eight bits is one byte. See also byte.
board: A circuit board. An internal
card containing electronic components,
called chips, which perform a specific
function or increase the capabilities of
the system.
bps: Bits per second. Typically used
to describe the data transmission
speed of a modem.
buffer: The portion of the computer’s
memory where data is temporarily
stored. Buffers often compensate for
differences in the rate of flow from
one device to another.
bus: An interface for transmission of
signals, data or electric power.
byte: The representation of a single
character. A sequence of eight bits
treated as a single unit; also the
smallest addressable unit within the
system.
C
cache memory: High speed memory
which stores data that increases
processor speed and data transfer rate.
When the CPU reads data from main
memory, it stores a copy of this data in
cache memory. The next time the CPU
needs that same data, it looks for it in
the cache memory rather than the main
memory, which saves time. The
computer has two cache levels. Level
one is incorporated into the processor
and level two resides in external
memory.
boot: Short for bootstrap. A program
that starts or restarts the computer.
The program reads instructions from a
storage device into the computer’s
memory.
Glossary-3
GLOSSARY
B
GLOSSARY
capacity
capacity: The amount of data that can
be stored on a magnetic storage
device such as a diskette (floppy
disk) or hard disk. It is usually
described in terms of kilobytes (KB),
where one KB = 1024 bytes and
megabytes (MB), where one MB =
1024 KB.
card: Synonym for board. See board.
CardBus: An industry standard bus
for 32-bit PC Cards.
CD-ROM: A Compact Disk-Read
Only Memory is a high capacity disk
that can be read from but not written
to. The CD-ROM drive uses a laser,
rather than magnetic heads, to read
data from the disk.
character: Any letter, number,
punctuation mark, or symbol used by
the computer. Also synonymous with
byte.
chassis: The frame containing the
computer.
chip: A small semiconductor containing computer logic and circuitry for
processing, memory, input/output
functions and controlling other chips.
CMOS: Complementary Metal-Oxide
Semiconductor. An electronic circuit
fabricated on a silicon wafer that
requires very little power. Integrated
circuits implemented in CMOS
technology can be tightly packaged
and are highly reliable.
cold start: Starting a computer that is
currently off (turning on the power).
Glossary-4
commands: Instructions you enter at
the terminal keyboard that direct the
actions of the computer or its peripheral devices.
communications: The means by
which a computer transmits and
receives data to and from another
computer or device.
compatibility: 1) The ability of one
computer to accept and process data in
the same manner as another computer
without modifying the data or the
media upon which it is being transferred. 2) the ability of one device to
connect to or communicate with
another system or component.
components: Elements or parts (of a
system) which make up the whole
(system).
computer program: A set of instructions written for a computer that
enable it to achieve a desired result.
computer system: A combination of
hardware, software, firmware, and
peripheral components assembled to
process data into useful information.
configuration: The specific components in your system (such as the
terminal, printer, and disk drives) and
the settings that define how your
system works. You use the HW Setup
program to control your system
configuration.
disk drive
controller: Built-in hardware and
software that controls the functions of
a specific internal or peripheral device
(e.g. keyboard controller).
co-processor: A circuit built into the
processor that is dedicated to intensive
math calculations.
CPS: Characters per second. Typically used to indicate the transmission
speed of a printer.
CPU: Central processing unit. The
portion of the computer that interprets
and executes instructions.
CRT: Cathode Ray Tube. A vacuum
tube in which beams projected on a
fluorescent screen-producing luminous
spots. An example is the television
set.
cursor: A small, blinking rectangle or
line that indicates the current position
on the display screen.
D
data: Information that is factual,
measurable or statistical that a
computer can process, store, or
retrieve.
data access arrangement: Circuitry
that isolates a modem or other device
from telephone lines.
data bits: A data communications
parameter controlling the number of
bits (binary digits) used to make up a
byte. If data bits = 7 the computer can
generate 128 unique characters. If
data bits = 8 the computer can
generate 256 unique characters.
DC: Direct Current. Electric current
that flows in one direction. This type
of power is usually supplied by
batteries.
default: The parameter value
automatically selected by the system
when you or the program do not
provide instructions. Also called a
preset value.
delete: To remove data from a disk
or other data storage device. Synonymous with erase.
device driver: A program that
controls communication between a
specific peripheral device and the
computer. The CONFIG.SYS file
contains device drivers that MS-DOS
loads when you turn the computer on.
dialog box: A window that accepts
user input to make system settings or
record other information.
disk drive: The device that randomly
accesses information on a disk and
copies it to the computer’s memory. It
also writes data from memory to the
disk. To accomplish these tasks, the
unit physically rotates the disk at high
speed past a read-write head.
Glossary-5
GLOSSARY
control keys: A key or sequence of
keys you enter from the keyboard to
initiate a particular function within a
program.
GLOSSARY
disk storage
disk storage: Storing data on magnetic
disk. Data is arranged on concentric
tracks much like a phonograph record.
diskette: A removable disk that stores
magnetically encoded data used on a
microcomputer. Also called floppy
disk.
display: A CRT, plasma screen, LCD,
or other image producing device used
to view computer output.
documentation: The set of manual
and/or other instructions written for the
users of a computer system or application. Computer system documentation
typically includes procedural and
tutorial information as well as system
functions.
DOS: Disk operating system. See
operating system.
driver: A software program, generally
part of the operating system, that
controls a specific piece of hardware
(frequently a peripheral device such as
a printer or mouse).
E
echo: To send back a reflection of the
transmitted data to the sending device.
You can display the information on the
screen, or output it to the printer, or
both. When a computer receives back
data it transmitted to a CRT (or other
peripheral device) and then retransmits
the data to printer, the printer is said to
echo the CRT.
Glossary-6
erase: See delete.
escape: 1) A code ( ASCII code 27),
signaling the computer that what
follows are commands; used with
peripheral devices such as printers and
modems. 2) A means of aborting the
task currently in progress.
escape guard time: A time before and
after an escape code is sent to the
modem which distinguishes between
escapes that are part of the transmitted data, and escapes that are intended as a command to the modem.
execute: To interpret and execute an
instruction.
Extended Capability Port: An industry
standard that provides a data buffer,
switchable forward and reverse data
transmission, and run length encoding
(RLE) support.
F
fast infrared: An industry standard
that enables cableless infrared serial
data transfer at speeds of up to 4
Mbps.
file: A collection of related information; a file can contain data, programs,
or both.
firmware: A set of instructions built
into the hardware which controls and
directs a microprocessor’s activities.
fixed disk: See hard disk.
hotkey
floppy disk drive (FDD): An electromechanical device that reads and writes to
floppy disks. See also diskette.
Fn-esse: A TOSHIBA utility that lets
you assign functions to hotkeys.
folder: An icon in Windows used to
store documents or other folders.
format: The process of readying a
blank disk for its first use. Formatting
establishes the structure of the disk
that the operating system expects
before it writes files or programs onto
the disk.
function keys: The keys labeled F1
through F12 that tell the computer to
perform certain functions.
G
gigabyte (GB): A unit of data
storage equal to 1024 megabytes.
See also megabyte.
GND: Ground. An RS-232C signal
used in the exchange of data between a
computer and serial device.
graphics: The use of drawings,
pictures, or other images, such as
charts or graphs, to present information.
H
hard disk: A non-removable disk
usually referred to as drive C. The
factory installs this disk and only a
trained engineer can remove it for
servicing. Also called fixed disk.
hard disk drive (HDD): An electromechanical device that reads and
writes a hard disk. See also hard disk.
hardware: The physical electronic
and mechanical components of a
computer system: typically, the
computer itself, external disk drives,
etc. See also software and firmware.
hertz: A unit of wave frequency that
equals one cycle per second.
hexadecimal: The base 16 numbering
system composed of the digits 0
through 9 and the letters A, B, C, D,
E, and F.
host computer: The computer that
controls, regulates, and transmits
information to a device or another
computer.
hot dock/undock: Connecting or
disconnecting a device to or from the
computer while the computer’s power
is turned on.
hotkey: The computer’s feature in
which certain keys in combination
with the extended function key, Fn,
can be used to set system parameters,
such as speaker volume.
Glossary-7
GLOSSARY
floppy disk: See diskette.
GLOSSARY
HW Setup
HW Setup: A TOSHIBA utility that
lets you set the parameters for various
hardware components.
I
icon: A small graphic image displayed
on the screen or in the indicator panel.
In Windows, an icon represents an
object that the user can manipulate.
infrared port: A cableless communications capable of using infrared
signals to send serial data.
input: The data or instructions you
provide to a computer, communication
device or other peripheral device from
the keyboard or external or internal
storage devices. The data sent (or
output) by the sending computer is
input for the receiving computer.
instruction: Statements or commands
that specify how to perform a particular task.
interface: 1) Hardware and/or
software components of a system
used specifically to connect one
system or device to another. 2) To
physically connect one system or
device to another to exchange
information. 3) The point of contact
between user, the computer, and the
program, for example, the keyboard or
a menu.
Glossary-8
interrupt request: A signal that gives
a component access to the processor.
I/O: Input/output. Refers to acceptance and transfer of data to and from
a computer.
I/O devices: Equipment used to
communicate with the computer and
transfer data to and from it.
J
jumper: A small clip or wire that
allows you to change the hardware
characteristics by electrically connecting two points of a circuit.
K
K: Taken from the Greek word kilo,
meaning 1000; often used as equivalent to 1024, or 2 raised to the 10th
power. See also byte and kilobyte.
KB: See kilobyte.
keyboard: An input device containing
switches that are activated by manually pressing marked keys. Each
keystroke activates a switch that
transmits a specific code to the
computer. For each key, the transmitted code is, in turn, representative of
the (ASCII) character marked on the
key.
monitor
M
main board: See motherboard.
L
.
level 2 cache: See cache.
Light Emitting Diode (LED): A
semiconductor device that emits light
when a current is applied.
Liquid Crystal Display (LCD): Liquid
crystal sealed between two sheets of
glass coated with transparent conducting material. The viewing-side
coating is etched into character
forming segments with leads that
extend to the edge of the glass.
Applying a voltage between the glass
sheets darkens the liquid crystal to
provide contrast to lighted portions of
the display.
LSI: Large Scale Integration. 1) A
technology that allows the inclusion of
up to 100,000 simple logic gates on a
single chip. 2) An integrated circuit
that uses the large scale integration.
megabyte (MB): A unit of data
storage equal to 1024 kilobytes. See
also kilobyte.
megahertz: A unit of wave frequency
that equals 1 million cycles per
second. See also hertz.
menu: A software interface that
displays a list of options on the
screen. Also called a screen.
microprocessor: A hardware component contained in a single integrated
circuit that carries out instructions.
Also called the central processing unit
(CPU), one of the main parts of the
computer.
mode: A method of operation, for
example, the boot mode or the resume
mode.
modem: Derived from modulator/
demodulator, a device that converts
(modulates) digital data for transmission over telephone lines and then
converts modulated data (demodulates) to digital format where received.
monitor: A device that uses rows and
columns of pixels to display alphanumeric characters or graphic images.
See CRT.
Glossary-9
GLOSSARY
kilobyte (KB): A unit of data storage
equal to 1024 bytes. See also byte
and megabyte.
GLOSSARY
motherboard
motherboard: A name sometimes used
to refer to the main printed circuit
board in processing equipment. It
usually contains integrated circuits
that perform the processor’s basic
functions and provides connectors for
adding other boards that perform
special functions. Sometimes called a
main board.
N
non-system disk: A formatted diskette
(floppy disk) you can use to store
programs and data but you cannot use
to start the computer. See system disk.
nonvolatile memory: Memory, usually
read-only (ROM), that is capable of
permanently storing information.
Turning the computer’s power off
does not alter data stored in nonvolatile memory.
numeric keypad overlay: A feature
that allows you to use certain keys on
the keyboard to perform numeric
entry, or to control cursor and page
movement.
Glossary-10
O
OCR: Optical Character Recognition
(reader). A technique or device that
uses laser or visible light to identify
characters and input them into a
storage device.
OCR wand: A device that reads, using
an optical device, hand written or
machine printed symbols into a
computer. See also OCR.
online state: A functional state of a
peripheral device when it is ready to
receive or transmit data.
operating system: A group of
programs that controls the basic
operation of a computer. Operating
system functions include interpreting
programs, creating data files, and
controlling the transmission and
receipt (input/output) of data to and
from memory and peripheral devices.
output: The results of a computer
operation. Output commonly indicates
data 1) printed on paper, 2) displayed
at a terminal, 3) sent through the serial
port of internal modem, or 4) stored on
some magnetic media.
Radio frequency interference (RFI) shield
parity: 1) The symmetrical relationship
between two parameter values (integers) both of which are either on or off;
odd or even; 0 or 1. 2) In serial
communications, an error detection bit
that is added to a group of data bits
making the sum of the bits even or odd.
Parity can be set to none, odd, or even.
password: A unique string of characters used to identify a specific user.
The computer provides various levels
of password protection such as user,
supervisor and eject.
pel: The smallest area of the display
that can be addressed by software.
Equal in size to a pixel or group of
pixels. See pixel.
peripheral component interconnect:
An industry standard 32-bit bus.
peripheral device: An I/O device that
is external to the central processor and/
or main memory such as a printer or a
mouse.
pixel: A picture element. The smallest
dot that can be made on a display or
printer. Also called a pel.
plug and play: A capability with
Windows that enables the system to
automatically recognize connections of
external devices and make the necessary configurations in the computer.
port: The electrical connection
through which the computer sends
and receives data to and from devices
or other computers.
printed circuit board (PCB): A
hardware component of a processor to
which integrated circuits and other
components are attached. The board
itself is typically flat and rectangular,
and constructed of fiberglass, to form
the attachment surface.
program: A set of instructions a
computer can execute that enables it to
achieve a desired result. See also
application.
prompt: A message the computer
provides indicating it is ready for or
requires information or an action from
you.
R
Radio frequency interference (RFI)
shield: A metal shield enclosing the
printed circuit boards of the printer or
computer to prevent radio and TV
interference. All computer equipment
generates radio frequency signals.
The FCC regulates the amount of
signals a computing device can allow
past its shielding. A Class A device is
sufficient for office use. Class B
provides a more stringent classification for home equipment use.
TOSHIBA portable computers comply
with Class B computing device
regulations.
Glossary-11
GLOSSARY
P
GLOSSARY
Random Access Memory (RAM)
Random Access Memory (RAM):
High speed memory within the
computer circuitry that can be read or
written to.
restart: Resetting a computer without
turning it off (also called ‘warm boot’
or ‘soft reset’). To restart the computer, press Ctrl + Alt + Del while the
computer is on. See also boot.
RGB: Red, green, and blue. A device
that uses three input signals, each
activating an electron gun for a
primary additive color (red, green, and
blue) or port for using such a device.
See also CRT.
soft key: Key combinations that
emulate keys on the IBM keyboard,
change some configuration options,
stop program execution, and access
the numeric keypad overlay.
software: The set of programs,
procedures and related documentation
associated with a computer system.
Specifically refers to computer
programs that direct and control the
computer system’s activities. See
also hardware.
RJ11: A modular telephone jack.
stop bit: One or more bits of a byte
that follow the transmitted character
or group codes in asynchronous serial
communications.
ROM: Read Only Memory: A
nonvolatile memory chip manufactured to contain information that
controls the computer’s basic operation. You cannot access or change
information stored in ROM.
subpixel: Three elements, one red,
one green and blue (RGB), that make
up a pixel on the color LCD. The
computer sets subpixels independently, each may emit a different
degree of brightness. See also pixel.
S
SCSI: Small Computer System
Interface is an industry standard
interface for connection of a variety of
peripheral devices.
SIO: Serial Input/Output. The
electronic methodology used in serial
data transmission.
Glossary-12
synchronous: Having a constant time
interval between successive bits,
characters or events.
system disk: A disk that has been
formatted with an operating system.
For MS-DOS the operating system is
contained in two hidden files and the
COMMAND.COM file. You can boot
a computer using a system disk. Also
called an operating system disk.
write protection
terminal: A typewriter-like keyboard
and CRT display screen connected to
the computer for data input/output.
TFT: A color LCD technology that
applies individual transistors to each
pixel enabling fine display control and
excellent screen legibility.
TOSHIBA Power Saver: A TOSHIBA
utility that lets you set the parameters
for various power-saving functions.
Touch pad: A pointing device integrated into the TOSHIBA computer
palm rest.
TTL: Transistor-transistor logic. A
logic circuit design that uses switching
transistors for gates and storage.
U
Universal Serial Bus: This serial
interface lets you communicate with
several devices connected in a chain to
a single port on the computer.
V
volatile memory: Random access
memory (RAM) that stores information as long as the computer is
connected to a power source.
W
Warm dock/undock: Connecting or
disconnecting a device to or from the
computer while the computer is
suspended.
warm start: Restarting or resetting a
computer without turning it off.
window: A portion of the screen that
can display its own application or
document. Often used to mean a
Microsoft Windows window.
Wireless LAN: A short-range radio
technology designed to simplify
wireless communication with other
LAN systems based on Direct
Sequence Spread Spectrum radio
technology that complies with the
IEEE 802.11 Standard (Revision B).
write protection: A method for
protecting a diskette (floppy disk)
from accidental erasure.
VGA: Video graphics array is an
industry standard video adaptor that
lets you run any popular software.
Glossary-13
GLOSSARY
T
GLOSSARY
Glossary-14
Index
D
AC adaptor 1-4, 2-10
DC IN 15V port 2-4
connecting 3-6
universal 1-10, 8-10
ASCII characters 5-9
Auto power on, See Power
DC IN indicator 2-8, 6-4
Disk indicator 2-8
Diskette care 4-4
Display 1-3, 2-6, See also Video
modes and Monitor external
automatic power off 1-6
controller 1-3, Appendix B
driver 1-9
hinge 2-6
opening 3-5
selection, See Hot keys
Documentation list 1-2
B
Battery, See also Battery Pack
charging 6-8
extending life 6-11
indicator 2-8, 6-4
lock 2-6, 6-12
monitoring capacity 6-9
real time clock 1-4, 6-6
safety precautions 6-7
save mode 1-7
types 6-5
Battery Charger 1-10, 8-11
Battery Pack 1-4, 1-10, 6-5, 8-10
High Capacity 2nd 1-10, 8-10
location 2-5
replacing 6-11
Boot priority 7-7
E
Environment 3-2
Equipment checklist 1-1
Equipment setup
general conditions 3-2
placement 3-2
Ergonomics
lighting 3-4
seating and posture 3-3
work habits 3-4
Expansion memory, See Memory
expansion
C
F
Cache memory
CPU cache 1-3
Level 2 cache 1-3
Charger, See Battery Charger
Cleaning the computer 4-14
Cooling 1-8, 4-15
Fn + 1 (volume decrease) 5-4
Fn + 2 (volume increase) 5-4
Fn + Alt (enhanced keyboard simulation) 5-3
Fn + Ctrl (enhanced keyboard simulation) 5-3
Fn + Enter 5-3
Index-1
INDEX
A
INDEX
User's Manual
Fn + Esc (sound mute) 5-4
Fn-esse 1-8
Fn + F1 (instant security) 5-4
Fn + F2 (power save mode) 5-5
Fn + F3 (standby) 5-5
Fn + F4 (hibernation) 5-5
Fn + F5 (display selection) 5-5
Fn + F6 (display brightness) 5-6
Fn + F7 (display brightness) 5-6
Fn + F10 (arrow mode) 5-3, 5-7
Fn + F11 (numeric mode) 5-3, 5-8
Fn + F12 (ScrLock) 5-3
Fn Sticky key 5-6
Function Keys 5-2
H
Hard disk drive 1-3
automatic power off 1-6
problems 9-9
Hibernation 1-7, 5-5
Hotkeys 1-6, 5-4
display brightness 5-6
display selection 5-5
hibernation 5-5
instant security 5-4
power save mode 5-5
standby 5-5
sticky key utility 5-6
volume decrease 5-4
volume increase 5-4
HW Setup 1-8
accessing 7-1
Boot Priority 7-7
CPU 7-6
Device Config 7-6
Display 7-6
General 7-4
LAN 7-9
Password 7-4
USB 7-8
window 7-2, 7-3
Index-2
I
Indicators 2-8, 6-4
Infrared port, See also Ports
problems 9-10
Instant security, See Hot keys
Interfaces, See Ports
Internet button 1-5, 2-6
K
Keyboard 1-4, 5-1
emulating enhanced keyboard 5-2
F1 . . . F12 function keys 5-2
problems 9-8
Typewriter keys 5-1
Keypad overlay 1-6, 5-7
arrow mode 5-7
numeric mode 5-8
temporarily changing modes 5-9
temporarily using normal keyboard
(overlay on) 5-8
temporarily using overlay (overlay
off) 5-9
turning on 5-7
Windows special keys 5-7
L
LAN, See also Wireless LAN 1-5
cable types 4-6
connecting 4-6
disconnecting 4-7
indicator 2-4
jack location 2-4
Network Device Switch 4-8
problems 9-17
Super Long Life scheme 4-10
using 4-6
LCD, See Display, Video modes and
Monitor external
Level 2 cache, See Cache memory
Lock, security, See Security lock
Index
M
N
Numeric keypad, See Keypad overlay
O
Operating system, See Windows
Overlay, See Keypad overlay
P
Panel power on/off, See Power
Password
power on 1-7
starting the computer with 6-14
supervisor 1-8, 7-9
user 7-4
PC card 1-5
installing 8-2
location of slots 2-3
problems 9-13
removing 8-4
Index-3
INDEX
Main battery, See Battery Pack
Memory 1-3
expansion 1-10, 8-6
installing 8-7
removing 8-9
slots 1-3
Microphone, See sound system,
microphone
Microprocessor, See Processor
Modem 1-5, 4-10
connecting 4-13
disconnecting 4-14
jack location 2-4
problems 9-15
properties menu 4-11
region selection 4-10
Monitor external 8-12, See also
Video modes and Ports
problems 9-14
Moving the computer 4-14
Ports
DC IN 15V 2-4
docking 2-5
external monitor 1-4, 2-4
headphone, See Sound system
infrared 1-4, 2-3
LAN 2-4
microphone, See Sound system
modem 2-4
USB 1-4, 2-4
Power
auto power on 1-7
button location 2-6
indicator 2-8, 6-5
panel power on/off 1-7
restarting 3-13
turning off 3-8
turning on 3-7
system auto off 1-7
Power cord 1-4, 2-10
Problems
analyzing symptoms 9-2
diskette drive 9-10
hard disk drive 9-9
hardware and system checklist 9-3
infrared port 9-10
keyboard 9-8
LAN 9-17
LCD panel 9-8
modem 9-15
monitor, external 9-14
password 9-7
PC card 9-13
power 9-4
preliminary checklist 9-1
SD card 9-13
self test 9-4
sound system 9-14
support from TOSHIBA 9-18
system start-up 9-3
Touch Pad 9-11
USB 9-15
User's Manual
USB mouse 9-12
Wireless LAN 9-17
Processor 1-3
R
Real time clock battery, See Battery
Recovery CD-ROM 3-13
INDEX
S
Screen, See Display
ScrLock (Fn + F12), See Soft keys
SD card 1-5
indicator 2-2
installing 8-5
location of slot 2-2
problems 9-13
removing 8-6
Security lock 1-10
attaching 8-13
location 2-2
Self Test, See Problems
Sensor switch 2-6
Slim Port Replicator 1-10, 8-11
Soft keys 5-2
cursor control mode 5-3
Enter 5-3
numeric mode 5-3
right Alt key 5-3
right Ctrl key 5-3
ScrLock 5-3
Sound system 1-5
drivers 1-9
headphone 1-4, 2-3
microphone 1-4, 2-3
problems 9-14
speaker 2-5
Standby 1-7
System auto off 1-7
Index-4
T
TOSHIBA Console button 1-5, 2-6
TOSHIBA Console 1-9
TOSHIBA Controls 1-9
TOSHIBA Power Saver 1-8
Touch Pad 1-4, 2-6
control buttons 2-6, 4-1
problems 9-11
using 4-1
Troubleshooting, See Problems
U
Utilities
list 1-8
USB 1-4
location 2-4
problems 9-15
USB FDD Kit 1-10, 8-11
connecting 4-3
disconnecting 4-4
problems 9-10
using 4-2
V
Video modes, Appendix B
Video RAM 1-3
W
Windows XP Professional setup 3-8
Windows 2000 setup 3-8
Wireless communication
indicator 2-8, 4-5
switch 2-3, 4-5
Wireless LAN 1-5
problems 9-17
using 4-5
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertisement