Apple iPhone 14 Plus Manual

System Configuration . After you've completed all removal and

and follow workspace and battery handling guidelines before you begin.

• Read Broken Glass

before you begin.

• Improper replacement, improper handling of parts, or failure to follow the provided instructions may cause malfunctions. Additionally, wireless charging may appear slow or the iPhone may not charge properly. These events could result in injury, or damage to the device, parts, or other property.

Tools

• 6.7-inch heated display pocket

• 6.7-inch repair tray

• Adhesive cutter

• Display adhesive press plate

• Display press

• ESD-safe tweezers

• Ethanol wipes or isopropyl (IPA) wipes

• Heated display removal fixture

• Heat-resistant gloves

• Micro stix bit

• Nylon probe (black stick)

• Safety glasses with side shields

• Torque driver (black, 0.35 kgf cm)

• Torque driver (blue, 0.65 kgf cm)

• Torx security bit

iPhone 14 Plus Back Glass | Before You Begin

Caution

• This procedure requires

reassembly steps, follow the instructions to initiate System Configuration.

• To avoid damaging the lenses, don't touch the camera assembly or nearby parts.

Important

Read Heated Display Removal Fixture if you’re setting up the fixture for the first time.

iPhone 14 Plus

Removal

1. Place the enclosure in the repair tray with the Lightning connector facing the cutout.

Back Glass | Removal

2. Use a torque driver and the

Torx security bit to remove the two security screws, one from each side of the

Lightning connector. Set aside the screws.

3. Flip the switch on the back of the heated display removal fixture to turn it on.

The internal fan will turn on. Wait for a checkmark to appear on the screen.

Note: If an error code appears on the screen, turn off the fixture and turn it back on.

iPhone 14 Plus

4. Take the iPhone out of the repair tray. Then gently insert it into the heated display pocket with the camera faceup and the

Lightning connector facing the bottom of the pocket.

Important

Ensure that the clamp on the side of the pocket is flipped up.

Caution

Don’t scratch the enclosure or the display as you insert the iPhone into the heated display pocket.

5. Flip down the clamp on the side of the pocket to lock the iPhone into place.

6. Put on the heat-resistant gloves. Align the cutout on the bottom of the pocket with the rail on the fixture. Slide the pocket with the iPhone onto the rail on the fixture.

Warning

Don’t insert the pocket into the fixture without wearing the heat-resistant gloves.

Back Glass | Removal

iPhone 14 Plus

7. Slide the pocket into the fixture until the pocket clicks into place.

Note: The screen on the fixture will turn red and the timer will count down from 2 minutes while the pocket heats to the correct temperature. When the timer shows 0, the fixture will start to beep and the screen will turn green.

Back Glass | Removal

073-00370-A | 26

iPhone 14 Plus

8. Turn the knob on the fixture to lower the suction cup as close to the iPhone as possible without touching the iPhone.

Caution

To avoid damaging the iPhone, don’t turn the knob before the timer ends.

Note: The fixture will beep until the suction cup is lowered.

Back Glass | Removal

iPhone 14 Plus

9. Grasp the handle and slide the suction cup straight out until the edge of the suction cup aligns close to the bottom edge of the back glass (1).

10. Turn the knob on the fixture clockwise to lower the suction cup onto the back glass (2). Then flip down the handle on the suction cup to secure the suction cup to the back glass (3).

Caution

Don’t let the suction cup hang over the edge of the back glass or you may damage the iPhone. If damaged, stop the repair.

You can find a service option at support.apple.

com/repair .

Important

After the suction cup is lowered onto the iPhone, the screen will begin a

15-minute countdown.

When the timer shows

0, the heated display removal fixture will turn off. Ensure that you complete steps 11 and 12 within this time frame.

Back Glass | Removal

073-00370-A | 28

iPhone 14 Plus

11. Slowly turn the knob on the fixture counterclockwise until the back glass begins to separate from the enclosure.

Important

If you don’t see a gap between the back glass and the enclosure immediately, wait 30 seconds. If you still don’t see a gap, turn the silver part of the knob counterclockwise until the back glass begins to separate from the enclosure.

Caution

Only turn the silver knob if you haven't seen a gap after waiting for

30 seconds.

12. Insert the edge of the adhesive cutter between the back glass and the enclosure. Run the cutter between the back glass and the enclosure to the right and left as shown until the glass partially releases from the enclosure.

Caution

To avoid damaging the flex cables, don’t tilt up the bottom of the display more than 5 degrees.

Back Glass | Removal

073-00370-A | 29

iPhone 14 Plus Back Glass | Removal

13. Flip up the handle to release the suction cup. Then gently slide the flat end of the black stick under the edge of the suction cup to release it from the back glass.

Caution

Don’t turn the knob. Turning the knob may damage the flex cables.

14. Press the eject button on the side of the pocket to release the pocket from the fixture.

15. Hold both sides of the pocket and slide it straight out of the fixture.

iPhone 14 Plus

16. Flip up the clamp on the side of the pocket to release the iPhone (1). Hold the edge of the iPhone and gently remove the iPhone from the pocket (2).

Caution

Don’t touch the camera lenses.

Back Glass | Removal

17. Place the iPhone into the repair tray with the camera faceup and the Lightning connector facing the cutout. Remove the gloves.

18. Slide the back glass slightly toward the bottom of the iPhone.

iPhone 14 Plus

19. Insert the edge of the adhesive cutter into the top of the iPhone between the back glass and the enclosure. Hold the adhesive cutter at a

45-degree angle. Start at the middle and cut along the top and sides of the iPhone until the back glass is free.

Caution

To avoid damaging the flex cables, don’t tilt the back glass more than 5 degrees.

20. Insert the repair tray suction cups into the slots in the repair tray.

Note: The icon on the bottom of the tray shows the direction to tilt up the back glass and the correct side to place the suction cups.

Back Glass | Removal

073-00370-A | 32

iPhone 14 Plus

21. Tilt up the back glass toward the suction cups. Press the top and bottom edges of the back glass to secure it to the suction cups.

Caution

Don’t damage the back glass flex cable as you tilt up the back glass.

Warning

•

If the battery is dented, punctured, or otherwise damaged, stop the repair. You can find a service option at support.

apple.com/repair .

•

If the back glass is broken, inspect the enclosure. If there are shards of glass in the enclosure, put on the safety glasses with side shields and cutresistant gloves. Use

ESD-safe tweezers to remove the shards.

Then use ethanol or

IPA wipes to remove any remaining shards from the adhesive on the perimeter of the enclosure. Vacuum any shards of glass from the workspace.

Back Glass | Removal

073-00370-A | 33

iPhone 14 Plus

22. Use a torque driver and the Micro stix bit to remove the trilobe screw from the upper cowling (1) and the two trilobe screws from the lower cowling (2). Set aside the screws.

23. Use ESD-safe tweezers to remove the lower cowling. Save the cowling for reassembly.

Back Glass | Removal

073-00370-A | 34

iPhone 14 Plus

24. Use ESD-safe tweezers to remove the upper cowling.

Save the cowling for reassembly.

25. Lift the ends of the battery flex cable (1) and the back glass flex cable (2) off the connectors.

Caution

You must disconnect the battery flex cable first to ensure that the iPhone stays turned off.

Important

Some iPhone 14 Plus models may have a white adhesive shim (1) under the battery flex cable. If you see a white adhesive shim, don’t lift the battery flex cable (2) or touch the white adhesive shim while lifting the end of the flex cable (3) off the connector.

Back Glass | Removal

073-00370-A | 35

iPhone 14 Plus Back Glass | Removal

26. Hold the back glass by the edges. Pull the tabs on the suction cups to release them from the back glass. Then set the back glass facedown on a clean, flat surface.

27. Remove the suction cups from the repair tray.

28. Use ESD-safe tweezers to pick up the back glass adhesive. Then pull the adhesive at a 45-degree angle to remove it from the enclosure. Repeat this process until all the adhesive is removed from the perimeter of the enclosure.

Caution

Don't touch the camera assembly, TrueDepth camera grounding springs, or nearby parts.

29. Use ethanol wipes or IPA wipes to clean all residual adhesive from the enclosure.

iPhone 14 Plus Back Glass | Reassembly

Reassembly

1. Place the enclosure in the repair tray with the Lightning connector facing the cutout.

Important

If you’re installing a replacement back glass, peel the protective liner from the top and underside of it.

2. Inspect the TrueDepth camera. Ensure that the top edge of the TrueDepth camera is under the lip of the enclosure.

Caution

If the TrueDepth camera is positioned incorrectly, use the black stick to move it into the correct position.

Warning

Inspect the enclosure for loose or extra screws and small parts, which can damage the battery and cause safety issues.

3. Align the replacement back glass adhesive over the enclosure. Ensure that the top hole of the adhesive aligns over the camera.

Caution

Ensure that you’ve removed all residual adhesive from the back glass and the enclosure before you apply the replacement back adhesive.

iPhone 14 Plus

4. The replacement back glass adhesive has a top release liner, a middle release liner, and a bottom release liner.

Grasp the tab on the bottom release liner. Then slowly pull the bottom release liner (1) out from under the adhesive (2) while pressing the adhesive onto the enclosure.

Important

Don’t remove the top release liner yet.

Bottom release liner

Adhesive

Note: The replacement back glass adhesive for your model may look different from the illustration, but the steps are the same.

Back Glass | Reassembly

073-00370-A | 38

iPhone 14 Plus Back Glass | Reassembly

5. Inspect the back glass adhesive to ensure that it’s positioned on the shelf of the enclosure. If the adhesive isn’t correctly positioned on the enclosure, repeat removal steps 28 and 29. Then repeat reassembly steps 1 through 5.

6. Place the display adhesive press plate on top of the enclosure with the icon in the top right corner as shown.

Important

Ensure that the back glass side of the iPhone is faceup in the repair tray.

7. Position the repair tray with the iPhone in the display press. Pull down the lever until the display press locks.

iPhone 14 Plus

8. Wait until the display press beeps and the timer shows 0.

Pull down the lever (1) and pull out the release knob (2). Then lift the lever (3).

Caution

To ensure that the back glass adhesive bonds correctly to the enclosure, don’t lift the lever until 30 seconds have passed.

9. Remove the repair tray from the display press and remove the press plate.

10. Remove the top release liner in a clockwise direction starting from the middle left side.

Important

Don’t remove the remaining release liners adhered around the edge of the enclosure.

Back Glass | Reassembly

Top release liner

iPhone 14 Plus Back Glass | Reassembly

11. Insert the suction cups into the repair tray.

12. Align the right edge of the back glass with the right edge of the enclosure. Gently press along the edges of the back glass to secure it to the suction cups.

Important

Don't press the back of the back glass to secure it to the suction cups. Pressing the back may affect functionality.

13. Press the ends of the back glass and battery flex cables to the connectors.

14. Position the upper and lower cowlings.

15. Use the black torque driver and Micro stix bit to install one new trilobe screw (923-02584) (1) into the upper cowling and two new trilobe screws (923-08382) (2) into the lower cowling.

iPhone 14 Plus

16. Peel the first strip of the middle release liner (1) counterclockwise, starting at the top right of the enclosure. Peel the second strip (2) clockwise, starting at the top right of the enclosure. Then peel the third strip (3) clockwise, starting at the bottom left of the enclosure.

Caution

The second strip of the middle release liner runs under one flex cable.

Don't damage the flex cable while removing the release liner.

Back Glass | Reassembly

Middle release liner

17. Inspect the back glass adhesive to ensure that it’s in the correct position and not damaged or wrinkled.

If the adhesive is damaged, remove it and apply replacement adhesive.

iPhone 14 Plus Back Glass | Reassembly

18. Repeat step 2 to ensure that the TrueDepth camera is in the correct position. Then continue to step 19.

Warning

Inspect the enclosure for loose or extra screws and small parts, which can damage the battery and cause safety issues.

19. Pull the tabs on the suction cups to release them from the back glass. Tilt down the back glass to rest on the enclosure.

20. Remove the suction cups from the repair tray.

21. Press the back glass in the four areas shown simultaneously. Then press along the edges of the back glass until it clicks into place and the back glass is flush with the enclosure.

Caution

• Ensure that the flex cables aren’t trapped between the back glass and the enclosure. Feel the edges of the back glass for variations or gaps. If the back glass isn’t flush, repeat all removal steps and check the flex cables for damage. Then repeat reassembly steps 1 through 21.

• Don’t touch the camera lenses.

iPhone 14 Plus

22. Turn the iPhone over in the repair tray so the display is faceup.

23. Position the repair tray with the iPhone display faceup in the display press. Pull down the lever until the display press locks.

Back Glass | Reassembly

iPhone 14 Plus

24. Wait until the display press beeps and the timer shows 0.

Pull down the lever (1) and pull out the release knob (2). Then lift the lever (3).

25. Remove the repair tray from the display press.

Back Glass | Reassembly

iPhone 14 Plus

26. Use the blue torque driver and Torx security bit to install two new security screws, one on each side of the Lightning connector. As you install the screws, press lightly on the display near the Lightning connector.

Count five clicks as you install each new screw to ensure that the screw is fully installed.

Caution

If the screws aren’t flush, remove and set aside the screws. Then repeat step

26 to install a new set of security screws. If the new screws still aren’t flush, repeat all removal and reassembly steps.

Note: Use the correct screw color for your model.

• Blue, purple, red, starlight

(923-08388)

• Midnight, yellow (923-08387)

Back Glass | Reassembly

iPhone 14 Plus Back Glass | Reassembly

Caution

•

System Configuration is required if you’ve installed a replacement back glass, battery, camera,

display, or TrueDepth camera. Disregard notifications about iPhone features on the Lock Screen until you complete System Configuration.

• After you’ve completed all removal and reassembly steps, initiate System Configuration. The method of initiating System Configuration will vary depending on the part or parts replaced.

• If you replaced the back glass, battery, camera, or display, initiate System

Configuration by putting the device into diagnostics mode . Tap Start Diagnostics and follow the onscreen prompts.

• If you replaced the TrueDepth camera, you will need the following:

• The latest version of Apple Service Utility installed on a Mac running macOS 12.4 or later

• Internet access

• A Lightning cable

After you’ve installed Apple Service Utility on a Mac, learn how to initiate the System

Configuration process at support.apple.com/self-service-repair .

iPhone 14 Plus

Display

Before You Begin

Display | Before You Begin

Warning

• Read

System Configuration . After you’ve completed all removal and

and follow workspace and battery handling guidelines before you begin.

• Read Broken Glass

before you begin.

Tools

• 6.7-inch heated display pocket

• 6.7-inch repair tray

• Adhesive cutter

• Display adhesive press plate

• Display press

• ESD-safe tweezers

• Ethanol wipes or isopropyl alcohol (IPA) wipes

• Heated display removal fixture

• Heat-resistant gloves

• Kapton tape

• Micro stix bit

• Nylon probe (black stick)

• Torque driver (black, 0.35 kgf cm)

• Torque driver (blue, 0.65 kgf cm)

• Torx security bit

iPhone 14 Plus Display | Before You Begin

Caution

• To avoid damaging the lenses, don’t touch the TrueDepth camera assembly or nearby parts.

• Don’t touch the back of the display. Touching the back of the display may affect image quality.

• This procedure requires

reassembly steps, follow the instructions to initiate System Configuration.

Important

Read Heated Display Removal Fixture if you’re setting up the fixture for the first time.

iPhone 14 Plus

Removal

Display | Removal

Important

If you're able to turn off the iPhone , skip to step 6. If you’re unable to turn off the iPhone, continue to step 1.

1. Complete all removal steps in the

back glass section. Then continue to step 2.

2. Place the enclosure in the repair tray with the camera faceup and the Lightning connector facing the cutout.

3. Place Kapton tape over the battery flex cable connector on the logic board.

4. Press the end of the back glass flex cable to the connector.

Caution

• Don’t reconnect the battery flex cable at this time.

• Don’t reinstall the upper and lower cowlings or back glass adhesive at this time.

5. Position the back glass on top of the enclosure. Remove the enclosure from the repair tray. Then place the enclosure back in the repair tray with the display faceup and the Lightning connector facing the cutout.

iPhone 14 Plus

6. Use a torque driver and the

Torx security bit to remove the two security screws, one from each side of the

Lightning connector. Set aside the screws.

7. Flip the switch on the back of the heated display removal fixture to turn it on.

The internal fan will turn on. Wait for a checkmark to appear on the screen.

Note: If an error code appears on the screen, turn off the fixture and turn it back on.

Display | Removal

iPhone 14 Plus

8. Take the iPhone out of the repair tray. Then gently insert the iPhone into the heated display pocket with the display faceup and the

Lightning connector facing the bottom of the pocket.

Important

Ensure that the clamp on the side of the pocket is flipped up.

Caution

Don’t scratch the iPhone as you insert it into the heated display pocket.

9. Flip down the clamp on the side of the pocket to lock the iPhone into place.

Display | Removal

iPhone 14 Plus

10. Put on the heat-resistant gloves. Align the cutout on the bottom of the pocket with the rail on the fixture. Slide the pocket with the iPhone onto the rail on the fixture.

Warning

Don’t insert the pocket into the fixture without wearing the heat-resistant gloves.

Display | Removal

iPhone 14 Plus

11. Slide the pocket into the fixture until the pocket clicks into place.

Display | Removal

iPhone 14 Plus

12. Turn the knob on the fixture clockwise to lower the suction cup as close to the iPhone as possible without touching the iPhone.

Caution

To avoid damaging the iPhone, don’t turn the knob before the timer ends.

Note: The fixture will beep until the suction cup is lowered.

13. Grasp the handle and slide the suction cup straight out until the edge of the suction cup aligns with the bottom edge of the display.

Caution

Failure to align the edges of the suction cup and the display may damage the iPhone.

Display | Removal

073-00370-A | 55

iPhone 14 Plus

14. Turn the knob on the fixture clockwise to lower the suction cup onto the display (1). Then flip down the handle on the suction cup to secure the suction cup to the display (2).

Important

After the suction cup is lowered onto the iPhone, the screen will begin a

15-minute countdown.

When the timer shows 0, the heated display removal fixture will turn off. Ensure that you complete steps

15 and 16 within this time frame.

15. Slowly turn the knob on the fixture counterclockwise until the display begins to separate from the enclosure.

Important

If you don’t see a gap between the display and the enclosure immediately, wait 30 seconds. If you still don’t see a gap, turn the silver part of the knob counterclockwise until the display begins to separate from the enclosure.

Display | Removal

073-00370-A | 56

iPhone 14 Plus

16. Insert the edge of the adhesive cutter between the display and the enclosure.

Run the cutter between the display and the enclosure to the right and left as shown until the display partially releases from the enclosure.

Caution

To avoid damaging the flex cables, don’t tilt up the bottom of the display more than 5 degrees.

Display | Removal

iPhone 14 Plus

17. Flip up the handle to release the suction cup (1). Then gently slide the flat end of the black stick under the edge of the suction cup to release it from the display (2).

Caution

Don’t turn the knob.

Turning the knob may damage the flex cables.

18. Press the eject button on the side of the pocket to release the pocket from the fixture.

Display | Removal

iPhone 14 Plus

19. Hold both sides of the pocket and slide it straight out of the fixture.

Display | Removal

20. Flip up the clamp on the side of the pocket to release the iPhone (1). Hold the area outlined in blue and gently remove the iPhone from the pocket (2).

Caution

Don't scratch the iPhone as you remove it from the heated display pocket.

21. Place the iPhone into the repair tray with the display faceup and the Lightning connector facing the cutout. Remove the gloves.

iPhone 14 Plus

22. Slide the display slightly toward the bottom of the iPhone.

23. Insert the edge of the adhesive cutter into the top of the iPhone between the display and the enclosure.

Hold the adhesive cutter at a 45-degree angle. Start at the middle and cut along the top and sides of the iPhone until the display is free.

Caution

To avoid damaging the flex cables, don’t tilt up the bottom of the display more than 5 degrees.

Display | Removal

iPhone 14 Plus

24. Insert the repair tray suction cups into the slots in the repair tray.

Note: The icon on the bottom of the tray shows the direction to tilt up the display and the correct side to place the suction cups.

25. Tilt up the display toward the suction cups. Press the top and bottom edges of the display to secure it to the suction cups.

Caution

• To avoid damaging the enclosure or display, ensure that the internal display clips are released before you tilt up the display.

• Don’t damage the flex cables as you tilt up the display.

Display | Removal

073-00370-A | 61

iPhone 14 Plus

26. Use a torque driver and the

Micro stix bit to remove two trilobe screws, one from the display connector cowling and one from ambient light sensor connector cowling.

Set aside the screws.

Display | Removal

27. Remove the display connector and ambient light sensor connector cowlings. Save the cowlings for reassembly.

28. Lift the ends of the display and ambient light sensor flex cables from the connectors.

29. Hold the display by the edges. Pull the tabs on the suction cups to release them from the display. Then set the display facedown on a clean, flat surface.

iPhone 14 Plus

30. Remove the suction cups from the repair tray.

31. Use ESD-safe tweezers to pick up the display adhesive.

Then pull the adhesive at a

45-degree angle to remove it from the enclosure. Repeat this process until all the adhesive is removed from the perimeter of the enclosure.

Caution

Don’t touch the

TrueDepth camera assembly, grounding springs, or nearby parts.

Display | Removal

iPhone 14 Plus

32. Use ESD-safe tweezers to remove the grounding foam from the top of the enclosure as shown.

Display | Removal

33. Use ethanol wipes or IPA wipes to clean all residual adhesive from the enclosure.

Caution

Don’t use ethanol wipes or IPA wipes on the display. Ethanol or isopropyl alcohol may damage the display and affect image quality.

iPhone 14 Plus Display | Reassembly

Reassembly

1. Inspect the internal display clips for damage before reassembly. Ensure that the internal display clips are at a 90-degree angle and aren’t bent or damaged.

Important

• If the internal display clips are damaged, you may need to replace the display.

• If you’re installing a replacement display, peel the protective liner from the top and underside of it.

2. Place the enclosure in the repair tray with the Lightning connector facing the cutout.

3. Align the replacement display adhesive over the enclosure with the grounding foam on top. Ensure that the top holes of the adhesive align over the TrueDepth camera assembly.

Caution

Ensure that you’ve removed all residual adhesive from the display and the enclosure before you apply the replacement display adhesive.

iPhone 14 Plus

4. The replacement display adhesive has a top release liner, a middle release liner, and a bottom release liner. Grasp the tab on the bottom release liner. Then slowly pull the bottom release liner (1) out from under the adhesive (2) while pressing the adhesive onto the enclosure.

Important

Don’t remove the top release liner yet.

Bottom release liner

Adhesive

Note: The replacement display adhesive for your model may look different from the illustration, but the steps are the same.

Display | Reassembly

073-00370-A | 66

iPhone 14 Plus Display | Reassembly

5. Inspect the display adhesive to ensure that it’s positioned on the lip of the enclosure. If the adhesive isn’t correctly positioned on the enclosure, repeat removal steps 31 through 33. Then repeat reassembly steps 1 through 5 with new display adhesive.

6. Use the black stick to gently adhere the grounding foam as shown.

Caution

• Don’t touch the

TrueDepth camera assembly while adhering the grounding foam.

• Failure to adhere the grounding foam may damage the display, Wi-Fi, or

TrueDepth camera.

7. Place the display adhesive press plate on top of the enclosure with the icon in the top right corner as shown.

iPhone 14 Plus

8. Position the repair tray with the iPhone in the display press. Pull down the lever until the display press locks.

Display | Reassembly

9. Wait until the display press beeps and the timer shows

0. Pull down the lever (1) and pull out the release knob (2).

Then lift the lever (3).

Caution

To ensure that the display adhesive bonds correctly to the enclosure, don’t lift the lever until 30 seconds have passed.

iPhone 14 Plus

10. Remove the repair tray from the display press and remove the press plate.

11. Use ESD-safe tweezers to remove the top release liner as shown.

Important

Don’t remove the middle release liner yet.

Display | Reassembly

Top release liner

12. Insert the suction cups into the repair tray.

13. Align the left edge of the display with the left edge of the enclosure. Gently press along the edges of the display to secure it to the suction cups.

iPhone 14 Plus

14. Press the ends of the display flex cable (1) and ambient light sensor flex cable (2) to the connectors.

Press evenly along the length of the connectors.

15. Position the display connector cowling (1) and ambient light sensor connector cowling (2) over the ends of the flex cables.

16. Use the black torque driver and Micro stix bit to install two new trilobe screws (923-08503), one into the ambient light sensor connector cowling and one into the display connector cowling.

Display | Reassembly

073-00370-A | 70

iPhone 14 Plus

17. Peel the first strip of the middle release liner (1) counterclockwise, starting at the bottom right of the enclosure. Peel the second strip (2) clockwise, starting at the bottom right of the enclosure. Then peel the third strip (3) clockwise, starting at the bottom left of the enclosure.

Caution

The third strip of the middle release liner runs under two flex cables.

Don't damage the flex cables while removing the release liner.

Display | Reassembly

Middle release liner

18. Inspect the display adhesive to ensure that it’s in the correct position and isn't damaged or wrinkled.

If the adhesive is damaged, remove it and apply replacement adhesive.

19. Pull the tabs on the suction cups to release them from the display. Tilt down the display to rest on the enclosure.

20. Remove the suction cups from the repair tray.

iPhone 14 Plus

21. Press all four corners of the display simultaneously.

Then press along the edges of the display until it clicks into place and the display is flush with the enclosure.

Caution

Ensure that the flex cables aren’t trapped between the display and the enclosure.

Feel the edges of the display for variations or gaps. If the display isn’t flush, repeat removal steps

7 through 33 and check the flex cables for damage.

Then repeat reassembly steps 1 through 21.

22. Position the repair tray with the iPhone in the display press. Pull down the lever until the display press locks.

Display | Reassembly

iPhone 14 Plus

23. Wait until the display press beeps and the timer shows 0.

Pull down the lever (1) and pull out the release knob (2). Then lift the lever (3).

24. Remove the repair tray from the display press.

Display | Reassembly

iPhone 14 Plus

25. Use the blue torque driver and Torx security bit to install two new security screws, one on each side of the Lightning connector.

As you install the screws, press lightly on the display near the Lightning connector. Count five clicks as you install each screw to ensure that the screw is fully installed.

Note: Use the correct screw color for your model.

• Blue, purple, red, starlight

(923-08388)

• Midnight, yellow (923-08387)

Caution

If the screws aren’t flush, remove and set aside the screws. Then repeat step

25 to install a new set of security screws. If the new screws still aren’t flush, repeat all removal and reassembly steps.

Display | Reassembly

Important

If you completed removal steps 1 through 5, continue to step 26. If it wasn’t necessary for you to perform steps 1 through 5, skip to the Caution alert at the end of this section.

iPhone 14 Plus

26. Take the iPhone out of the repair tray. Then gently insert it into the heated display pocket with the camera faceup and the

Lightning connector facing the bottom of the pocket.

Display | Reassembly

27. Place the heated display pocket into the heated display removal fixture. Don’t turn on the fixture.

28. Turn the knob on the fixture clockwise to lower the suction cup onto the back glass. Then flip down the handle on the suction cup to secure the suction cup to the back glass.

Caution

Don’t let the suction cup hang over the edge of the back glass or you may damage the iPhone. If damaged, stop the repair.

You can find a service option at support.apple.

com/repair .

iPhone 14 Plus

29. Slowly turn the knob on the fixture counterclockwise until the back glass separates from the enclosure.

Important

To avoid damaging the back glass flex cable, don’t tilt up the back glass more than 5 degrees.

Display | Reassembly

30. Flip up the handle to release the suction cup. Then gently slide the end of the black stick under the edge of the suction cup to release it from the back glass.

31. Press the eject button on the side of the pocket to release the pocket from the fixture.

32. Place the enclosure in the repair tray with the camera faceup and the Lightning connector facing the cutout. Set aside the back glass on a clean surface.

33. Remove the Kapton tape from the battery flex cable connector.

Note: Don’t reconnect the battery flex cable at this time.

34. Complete all reassembly steps in the back glass

section. Then read the Caution alert below.

iPhone 14 Plus Display | Reassembly

Caution

•

System Configuration is required if you’ve installed a replacement back glass, battery, camera,

display, or TrueDepth camera. Disregard notifications about iPhone features on the Lock Screen until you complete System Configuration.

• After you’ve completed all removal and reassembly steps, initiate System Configuration. The method of initiating System Configuration will vary depending on the part or parts replaced.

• If you replaced the back glass, battery, camera, or display, initiate System

Configuration by putting the device into diagnostics mode . Tap Start Diagnostics and follow the onscreen prompts.

• If you replaced the TrueDepth camera, you will need the following:

• The latest version of Apple Service Utility installed on a Mac running macOS 12.4 or later

• Internet access

• A Lightning cable

After you’ve installed Apple Service Utility on a Mac, learn how to initiate the System

Configuration process at support.apple.com/self-service-repair .

iPhone 14 Plus

Camera

Before You Begin

Camera | Before You Begin

Warning

Read

and follow workspace and battery handling guidelines before you begin.

Remove the following part before you begin:

•

This procedure requires System Configuration . After you’ve completed all removal and reassembly

Tools

• 6.7-inch repair tray

• ESD-safe tweezers

• JCIS bit

• Nitrile or lint-free gloves

• Nylon probe (black stick)

• Torque driver (teal, 0.75 kgf cm)

iPhone 14 Plus

Caution

Avoid touching the camera lenses, TrueDepth camera grounding springs, or nearby parts.

Camera | Before You Begin

Important

If your iPhone has an mmWave antenna, you will need to disconnect an extra flex cable. Check the side of your iPhone to determine if you have an mmWave antenna.

mmWave antenna

Caution

steps, follow the instructions to initiate System Configuration.

iPhone 14 Plus

Removal

1. Place the enclosure in the repair tray with the Lightning connector facing the cutout.

2. Put on the gloves to prevent contamination of the camera lenses.

Camera | Removal

3. Use a torque driver and the

JCIS bit to remove the three crosshead screws from the camera cowling. Set aside the screws.

Caution

Avoid touching the camera lenses.

4. Lift the ends of the two camera flex cables from the connectors (1).

Important

If your iPhone has an mmWave antenna, lift the end of the mmWave antenna flex cable off the connector (2).

iPhone 14 Plus

5. Use the black stick to loosen the adhesive between the lower camera flex cable and the camera well.

Camera | Removal

iPhone 14 Plus

6. Use the black stick or

ESD-safe tweezers to tilt up the top side of the camera. Then remove the camera from enclosure.

Important

If your iPhone has an mmWave antenna, lift the mmWave antenna flex cable and place it slightly to the side as shown (1). Then use ESD-safe tweezers to lift the camera and the camera flex cables (2, 3) out of the enclosure.

Caution

The mmWave antenna stays in the enclosure.

Don’t remove it.

Camera | Removal

073-00370-A | 82

iPhone 14 Plus

Reassembly

Important

A protective cover is included with a replacement camera.

Leave the cover on while installing the new camera.

1. Put on the gloves to prevent contamination of the camera lenses.

2. Position the camera in the enclosure with the lenses faceup. Ensure that the camera flex cables are inside the channel between the battery and the camera well.

Important

If your iPhone has an mmWave antenna, position the mmWave antenna flex cable (1) and camera flex cables (2, 3) inside the channel between the battery and the camera well as shown.

Camera | Reassembly

iPhone 14 Plus Camera | Reassembly

3. Press the ends of the camera flex cables to the connectors.

Important

If your iPhone has an mmWave antenna, press the end of the mmWave antenna flex cable to the connector.

4. Use the teal torque driver and JCIS bit to install three new crosshead screws (923-08383) into the camera.

Reinstall the following part to complete reassembly:

•

Important

Remove the protective cover from the replacement camera before you reinstall the back glass.

Caution

After you’ve completed all removal and reassembly steps, initiate System Configuration by putting the device into diagnostics mode . Tap Start Diagnostics and follow the onscreen prompts.

iPhone 14 Plus

Taptic Engine

Before You Begin

Taptic Engine | Before You Begin

Warning

Read

and follow workspace and battery handling guidelines before you begin.

Remove the following part before you begin:

•

Tools

• 6.7-inch repair tray

• ESD-safe tweezers

• JCIS bit

• Nylon probe (black stick)

• Super screw bit

• Torque driver (blue, 0.65 kgf cm)

• Torque driver (orange, 0.85 kgf cm)

• Torque driver (teal, 0.75 kgf cm)

iPhone 14 Plus Taptic Engine | Removal

Removal

1. Place the enclosure in the repair tray with the Lightning connector facing the cutout.

2. Use a torque driver and the

JCIS bit to remove the two crosshead screws (1, 2) from the Taptic Engine connector cowling. Set aside the screws.

3. Remove the Taptic Engine connector cowling and save it for reassembly.

4. Use a torque driver and the

JCIS bit to remove the two crosshead screws (3) from the Taptic Engine. Set aside the screws.

5. Use a torque driver and the super screw bit to remove the super screw from the

Taptic Engine. Set aside the screw.

iPhone 14 Plus

6. Lift the end of the

Taptic Engine flex cable off the connector.

7. Remove the Taptic Engine from the enclosure.

Taptic Engine | Removal

iPhone 14 Plus

Reassembly

1. Position the Taptic Engine in the enclosure.

2. Press the end of the

Taptic Engine flex cable to the connector.

Taptic Engine | Reassembly

3. Use the teal torque driver and super screw bit to install one new super screw (923-08507) into the Taptic Engine.

iPhone 14 Plus

4. Position the Taptic Engine connector cowling over the end of the flex cable.

Taptic Engine | Reassembly

5. Use the blue torque driver and JCIS bit to install one new crosshead screw (923-08505) (1) into the Taptic Engine connector cowling.

6. Use the orange torque driver and JCIS bit to install one new crosshead screw (923-08508) (2) into the Taptic Engine connector cowling.

7. Use the teal torque driver and JCIS bit to install two new crosshead screws (923-08509) (3) into the

Taptic Engine.

Reinstall the following part to complete reassembly:

•

iPhone 14 Plus

TrueDepth Camera

Before You Begin

TrueDepth Camera | Before You Begin

Warning

• Read

and follow workspace and battery handling guidelines before you begin.

• The TrueDepth camera includes one or more lasers. Disassembly of the TrueDepth camera, damage to the TrueDepth camera, or failure to use genuine Apple parts could expose you to hazardous infrared laser emissions, possibly resulting in injuries to eyes or skin.

Remove the following part before you begin:

•

System Configuration . To perform System Configuration you will need the

Tools

• 6.7-inch repair tray

• ESD-safe tweezers

• Micro stix bit

• Nitrile or lint-free gloves

• Nylon probe (black stick)

• Torque driver (black, 0.35 kgf cm)

Caution

Avoid touching the camera lenses, TrueDepth camera grounding springs, or nearby parts.

iPhone 14 Plus TrueDepth Camera | Before You Begin

Caution

This procedure requires

following:

• The latest version of Apple Service Utility installed on a Mac running macOS 12.4 or later

• Internet access

• A Lightning cable

After you’ve completed all removal and reassembly steps and installed Apple Service Utility on a

Mac, learn how to initiate the System Configuration process at support.apple.com/self-service-repair .

iPhone 14 Plus TrueDepth Camera | Removal

Removal

1. Place the enclosure in the repair tray with the Lightning connector facing the cutout.

2. Put on the gloves to prevent contamination of the camera lenses.

3. Use a torque driver and the

Micro stix bit to remove the two trilobe screws from the TrueDepth camera connector cowling. Set aside the screws.

4. Remove the TrueDepth camera connector cowling and save it for reassembly.

iPhone 14 Plus

5. Lift the ends of the two

TrueDepth camera flex cables off the connectors.

6. Gently hold the flex cables together and lift the

TrueDepth camera out of the enclosure.

TrueDepth Camera | Removal

iPhone 14 Plus

Reassembly

1. Put on the gloves to prevent contamination of the camera lenses.

2. Inspect the TrueDepth camera assembly to ensure that the grounding foam and grounding springs are intact. If either is missing or damaged, replace the TrueDepth camera assembly.

TrueDepth Camera | Reassembly

3. Use ESD-safe tweezers to remove the protective cover from the TrueDepth camera.

iPhone 14 Plus

4. Position the TrueDepth camera in the enclosure.

Ensure that the top edge of the TrueDepth camera is under the lip of the enclosure as shown. If it’s positioned incorrectly, use the black stick to move it into the correct position.

Caution

• Don’t press on the bridge of the

TrueDepth camera when positioning it in the enclosure.

• Don’t touch the front of the TrueDepth camera assembly after you remove the protective cover.

TrueDepth Camera | Reassembly

5. Press the ends of the two TrueDepth camera flex cables to the connectors.

6. Position the TrueDepth camera connector cowling over the ends of the flex cables.

iPhone 14 Plus

7. Use the black torque driver and Micro stix bit to install two new trilobe screws (923-08382) into the TrueDepth camera connector cowling.

TrueDepth Camera | Reassembly

Reinstall the following part to complete reassembly:

•

Caution

• After you’ve completed all removal and reassembly steps, learn how to initiate the System

Configuration process at support.apple.com/self-service-repair .

• You will need a Mac with Apple Service Utility installed to perform System Configuration.

iPhone 14 Plus

Battery

Before You Begin

Battery | Before You Begin

Warning

• A battery should be replaced only by individual technicians with the knowledge and experience to repair electronic devices. Improper battery replacement, improper handling of parts, or failure to follow the provided instructions could result in fire, injury, data loss, or damage to the device, parts, or other property.

• Read

and follow workspace and battery handling guidelines before you begin.

Remove the following parts before you begin:

•

•

This procedure requires System Configuration

Tools

• 6.7-inch repair tray

• Battery press

• ESD-safe cleaning solution

• ESD-safe tweezers

• Ethanol wipes or isopropyl alcohol (IPA) wipes

• Heat-resistant gloves

• Nylon probe (black stick)

• Safety glasses with side shields

• Sand

• Sand container

iPhone 14 Plus

Caution

Avoid touching the

TrueDepth camera assembly, grounding springs, or nearby parts.

Battery | Before You Begin

Caution

. After you’ve completed all removal and reassembly steps, follow the instructions to initiate System Configuration.

iPhone 14 Plus

Removal

1. Place the enclosure in the repair tray with the Lightning connector facing the cutout.

Important

Some iPhone 14 Plus models may have a white adhesive shim under the battery flex cable. If you see a white adhesive shim (1), use ESD-safe tweezers to gently lift the flex cable from the adhesive shim (2). Then use the tweezers to remove the shim and discard it (3).

Battery | Removal

iPhone 14 Plus

2. Use ESD-safe tweezers to grasp the top right battery adhesive tab. Gently peel the adhesive tab away from the battery.

Warning

Don't scrape or puncture the battery with the tweezers.

Note: The battery has two adhesive tabs.

Battery | Removal

iPhone 14 Plus

3. Twist the tab around the tweezers and pull up 1 inch until you see white adhesive strip on the tweezers.

Battery | Removal

4. Keep the tweezers close and parallel to the battery. Then pull the tweezers toward the top of the iPhone and continue to twist and pull the adhesive until you’ve removed the entire strip.

Caution

Don’t pull the adhesive strip against parts or screws.

Important

If the battery adhesive tab or strip breaks off and you can still see it, attempt to retrieve it with the tweezers. Wrap the tab or strip around the tweezers and repeat step 4. If you can’t see the tab or strip, continue to the next step.

5. Use ESD-safe tweezers to grasp the top left battery adhesive tab. Gently peel the adhesive tab away from the battery.

6. Repeat steps 3 and 4.

Important

iPhone 14 Plus Battery | Removal

7. If both battery adhesive strips were fully removed, continue to step 10. If at least one strip was fully removed, continue to step 8.

Warning

If both strips were broken and can’t be retrieved, don’t forcibly pry the battery. Stop the repair. You can find a service option at support.apple.com/repair .

8. Insert the flat end of the black stick only into the insertion point as shown.

Don’t insert the black stick into a point where the battery tab or strip is broken.

iPhone 14 Plus Battery | Removal

9. Slightly lift the battery with black stick just enough to grasp underneath the battery.

Caution

To avoid damage, don’t press the black stick on the edge of the enclosure as you lift the battery.

10. Remove the battery from the enclosure. Then inspect the enclosure for damage. If the enclosure is damaged, replace the iPhone.

Warning

If you can’t remove the battery, stop the repair. You can find a service option at support.apple.com/repair .

iPhone 14 Plus Battery | Reassembly

Reassembly

1. Use ethanol wipes or IPA wipes to remove all residual adhesive from the enclosure underneath the battery.

2. Peel the pink release liner from the underside of the replacement battery.

Important

Don’t remove the protective cover from the top of the battery yet.

3. Hold the battery over the enclosure with the protective cover faceup. Align the top of the battery with the camera sidewall (1) and the right edge with the logic board (2). Then lower the battery into the enclosure.

iPhone 14 Plus

4. The center of the repair tray has two slots. Position the repair tray and enclosure onto the battery press with one slot of the repair tray on one side of the battery press.

5. Flip down the red lever at the top of the battery press to lower the roller onto the battery.

6. Slide the repair tray back and forth through the battery press three times to adhere the battery to the enclosure.

Battery | Reassembly

073-00370-A | 105

iPhone 14 Plus

7. Flip up the red lever.

8. Position the repair tray and enclosure to the other side of the battery press.

Battery | Reassembly

9. Repeat steps 5 through 7. Then continue to step 10.

10. Remove the repair tray from the battery press.

11. Hold the edges of the protective cover. Pull the release tabs on the protective cover to remove the cover from the battery.

Important

Don’t press the area over the tab you’re releasing.

iPhone 14 Plus

Reinstall the following parts to complete reassembly:

•

•

Gently shake the iPhone. If the battery sounds loose, remove the back glass

Battery | Reassembly

Warning

and the

battery

. Then complete battery reassembly with another replacement battery.

Important

A new battery is not charged. After you’ve completed all removal and reassembly steps, charge the device for a few minutes.

Caution

After you’ve completed all removal and reassembly steps, initiate System Configuration by putting the device into diagnostics mode . Tap Start Diagnostics and follow the onscreen prompts.

iPhone 14 Plus

Bottom Speaker

Before You Begin

Bottom Speaker | Before You Begin

Warning

Read

and follow workspace and battery handling guidelines before you begin.

Remove the following parts before you begin:

•

•

Taptic Engine

Tools

• 6.7-inch repair tray

• ESD-safe tweezers

• JCIS bit

• Micro stix bit

• Nylon probe (black stick)

• Torque driver (gray, 0.55 kgf cm)

• Torque driver (green, 0.45 kgf cm)

Caution

Avoid touching the grounding springs on and near the bottom speaker.

iPhone 14 Plus Bottom Speaker | Removal

Removal

1. Place the enclosure in the repair tray with the Lightning connector facing the cutout.

2. Use a torque driver and the

JCIS bit to remove the five crosshead screws from the bottom speaker. Set aside the screws.

3. Use a torque driver and the Micro stix bit to remove the trilobe screw from the bottom speaker. Set aside the screw.

iPhone 14 Plus

4. Remove the bottom speaker from the enclosure.

Caution

• Don’t lift the vent cowling (1) while removing the bottom speaker.

• Don’t damage the grounding spring (2) on the bottom speaker.

Bottom Speaker | Removal

iPhone 14 Plus

Reassembly

1. Ensure that the rubber gasket is positioned as shown. If the gasket is out of position, use ESD-safe tweezers to reposition it.

2. Position the bottom speaker in the enclosure. Slide the bottom right screw hole of the bottom speaker under the vent cowling screw hole as shown.

Caution

Don’t lift the vent cowling (1) while positioning the bottom speaker.

Bottom Speaker | Reassembly

073-00370-A | 111

iPhone 14 Plus

3. Use the green torque driver and Micro stix bit to install one new trilobe screw

(923-08382) (1) into the bottom speaker.

4. Use the gray torque driver and JCIS bit to install the following five new crosshead screws into the bottom speaker:

• Three crosshead screws

(923-08505) (2)

• One crosshead screw

(923-08502) (3)

• One crosshead screw

(923-08571) (4)

Caution

Don't damage the grounding springs on the bottom speaker.

Reinstall the following parts to complete reassembly:

•

Taptic Engine

•

Bottom Speaker | Reassembly

iPhone 14 Plus

Top Speaker

Before You Begin

Top Speaker | Before You Begin

Warning

Read

and follow workspace and battery handling guidelines before you begin.

Remove the following parts before you begin:

•

•

•

TrueDepth camera

Tools

• 6.7-inch repair tray

• ESD-safe tweezers

• JCIS bit

• Nylon probe (black stick)

• Torque driver (blue, 0.65 kgf cm)

• Torque driver (gray, 0.55 kgf cm)

iPhone 14 Plus

Removal

1. Place the enclosure in the repair tray with the Lightning connector facing the cutout.

Top Speaker | Removal

2. Use a torque driver and the JCIS bit to remove the crosshead screw from the sidewall of the enclosure.

Keep the torque driver as perpendicular as possible to avoid stripping the screw.

Set aside the screw.

3. Use a torque driver and the JCIS bit to remove the seven crosshead screws from the top speaker. Set aside the screws.

iPhone 14 Plus

4. Lift ends of the top speaker and back glass antenna flex cables from the connectors.

5. Remove the top speaker from the enclosure.

Top Speaker | Removal

iPhone 14 Plus

Reassembly

1. Position the top speaker in the enclosure.

2. Press the ends of the top speaker and back glass antenna flex cables to the connectors.

Top Speaker | Reassembly

3. Use the gray torque driver and JCIS bit to install one new crosshead screw

(923-08504) into the sidewall of the enclosure.

Keep the torque driver as perpendicular as possible to avoid stripping the screw.

iPhone 14 Plus

4. Use the blue torque driver and JCIS bit to install four new crosshead screws

(923-08506) (1)

(923-08510) (5) into the top speaker.

5. Use the gray torque driver and JCIS bit to install the following three new crosshead screws into the top speaker:

• One crosshead screw

(923-08504) (2)

• One crosshead screw

(923-08511) (3)

• One crosshead screw

(923-08505) (4)

Reinstall the following parts to complete reassembly:

•

TrueDepth camera

•

•