Cannon Fitzroy FITZIB-PMEXx Instruction manual

Cannon Fitzroy FITZIB-PMEXx Instruction manual
Gas Log Heaters
Sharing a lifetime of cosy moments
Inbuilt Heater
Instruction Manual
Please read this manual before
installing and using this heater.
Fitzroy
Canterbury
FITZIB-SDENB, FITZIB-SDENP
CANTIB-SDEEB
This heater is approved for Natural and Propane gases
Distributor
This appliance is designed, manufactured and distributed by:
Tel: 1300 727 421
Please leave instruction manual with the owner
CONTENTS
PAGE
WARRANTY
3-4
SAFETY WARNINGS
5
OPERATION
6
OPTIONAL ACCESSORIES
7
FITZROY INBUILT SPECIFICATIONS
8
CANTERBURY INBUILT SPECIFICATIONS
9
FITZROY & CANTERBURY INBUILT INSTALLATION INSTRUCTIONS
10 - 11
FITZROY & CANTERBURY INBUILT FLUEING OPTIONS
12
FITZROY INBUILT FASCIA REMOVAL
13
CANTERBURY INBUILT FASCIA REMOVAL
13
ELECTRICAL CONNECTION & SEALING THE FASCIA
14
INSTALLING THE FLUE SPIGOT
14
LOG INSTALLATION & GAS CONNECTION
15
SETTING THE GAS PRESSURE
16
SERVICE INSTRUCTIONS
17 - 18
WIRING DIAGRAM
19
TROUBLESHOOTING
20 -21
NOTES
22 - 23
2 | Cannon Fitzroy / Canterbury Inbuilt
WARRANTY
This Warranty against defects for your newly purchased
Cannon product is proudly prepared by Sampford IXL Pty
Ltd of 391 Boundary Rd, Truganina, Vic 3029,
phone 1300 727 421.
1. Sampford IXL products come with guarantees that do
not exclude the following consumer entitlements under
the Australian Consumer Law:
a. replacement or refund for a major failure and
compensation for any other reasonably foreseeable
loss or damage; and
b. to have the goods repaired or replaced if goods fail
to be of acceptable quality and the failure does not
amount to a major failure.
2. Sampford IXL warrants that your product and related
supply will be free from defects in materials and
workmanship during the warranty term.
Your warranty term is 3 years (10 years on the heat
exchanger parts only), commencing from the date of
purchase. Sampford IXL acknowledges this product
requires professional installation and product removal is
hazardous to consumers. Accordingly any necessary
inspections and services will be carried out on site.
You should not attempt de-installation.
c. will not apply where the defect in or failure of
the product is attributable to misuse, abuse,
accident or non-observation of the manufacturer’s
instructions. This product must be used in
accordance with the manufacturer’s instructions;
d. will not cover faults due to normal wear and tear
with reasonable use nor consumable components
such as globes, filters, glass items, etc;
e. will not cover any damages or problems caused to
this product by natural forces e.g. storm, fire, flood,
and earthquake; or by intrusion or accumulation
(or both) of foreign matters e.g. dust, soil, and
moisture. Sampford IXL recommends that you take
out appropriate insurances to protect your product
to this end;
f.
will not apply if this product is installed in a mobile
dwelling e.g. caravan or boat;
g. will not apply if this product is removed from the
location where it was first installed;
h. is immediately void if the serial or model number
label is removed or defaced;
i.
is immediately void if the product is serviced or
repaired by an unauthorised/unqualified personnel;
j. covers use of this product for domestic use only;
3. Subject to Point 1, Sampford IXL will repair any defects
in materials and workmanship during the warranty
k. will not be restarted or extended upon repair or
term and if the product is deemed irreparable provide
replacement of the product or a part.
a replacement of an equivalent current model where
the balance of the warranty period from the original
How to Make a Claim Under Your Cannon Warranty
date of purchase will take effect.
7. To make a claim under this Warranty you will need to:
4. To the fullest extent permitted by law and subject
always to Point 1, Sampford IXL will not be liable for:
a. any loss or damage arising from loss of use, loss
of profits or revenue; or
b. for any indirect or consequential loss or damage
resulting from any breach of this warranty
against defects.
5. Defective Sampford IXL products may be repaired
using refurbished parts or if required, completely
replaced by a refurbished product of the same type.
Limitations to Your Cannon Warranty
6. Subject to Point 1, this Warranty:
a. will only be provided to the original purchaser
where the original purchase was made from a
Sampford IXL Authorised Dealer or reseller and
proof of such purchase can be presented at the
time of service;
b. only applies to Sampford IXL products purchased
in Australia from a Sampford IXL Authorised Dealer
or reseller and installed by a qualified person
where a Certificate of Compliance in accordance
with State/Territory laws is provided;
a. contact Sampford IXL service department on 1300
727 421 or [email protected]
to provide details and register your claim enabling
a Sampford IXL assessment;
b. submit proof of purchase with your claim
e.g. tax invoice or purchase receipt;
c. where a property has been constructed by a
builder/developer and it is fitted with Cannon products,
please submit proof of purchase by way of the
certificate of occupancy, with your claim.
8. Sampford IXL will contact you to make arrangements
for service on site.
9. Subject to Point 1, you will be responsible for any
costs relating to the provision of your product to a
Sampford IXL Authorised Service Dealer.
10.Subject to Point 1, in the event you live more than
50 km from a Sampford IXL Authorised Service Dealer
you may be subject to travel or transport costs to
facilitate the repairing or replacement of your
Cannon product.
Cannon Fitzroy / Canterbury Inbuilt | 3
11.Sampford IXL and its Authorised Service Dealers
reserve the right to seek reimbursement of any costs
incurred by them should your Cannon product be
found to be in good working order.
Privacy
The privacy of your personal information has always
been important to us. To learn more about how we
collect, keep and use your personal information, please
obtain a copy of our privacy statement by visiting our
website at www.sampfordixl.com.au or by contacting
us via email on [email protected] or by telephone
on 1300 727 421.
Enter the details of the date installed and the
Compliance Certificate number in the appropriate
area on the rear page of this manual.
DO NOT operate this appliance before reading the
instruction manual.
DO NOT place articles on or against this appliance.
DO NOT store chemicals or flammable
materials, or spray aerosols near this appliance.
DO NOT operate with panels, covers or guards
removed from this appliance.
DO NOT connect an LP gas cylinder located indoors.
Don’t risk your appliance warranty.
Only a licensed person will give you a
Compliance Certificate, showing that the work
complies with all the relevant standards.
Only a licensed person will have insurance
protecting their workmanship for 6 years.
You MUST use a licensed person to install this
appliance who MUST give you your Compliance
Certificate to ensure the manufacturers appliance
warranty will be honoured.
4 | Cannon Fitzroy / Canterbury Inbuilt
SAFETY WARNINGS
Please read this manual before installing and using
the heater.
DO NOT INSTALL OR USE THIS APPLIANCE IN
MARINE CRAFT OR MOBILE HOMES.
Safety Warnings
DO NOT SPRAY AEROSOLS IN THE VICINITY OF
THIS APPLIANCE WHILE IT IS IN OPERATION.
1. What to do if you smell gas
a. Turn OFF the main gas supply
b. Extinguish any open flame
c. Open windows
d. Do not touch electrical switches
e. Do not use your telephone
f. Call your gas supplier immediately from
a neighbour’s phone
2. Improper installation, adjustment, alteration, service
or maintenance can cause injury or property damage.
Refer to the sections of this manual for correct
procedures, or consult with place of purchase, a
licensed plumber, a gas supplier or the Cannon
distributor listed in this manual.
3. Install the heater only in locations that are referred to
in the installation instructions. Do not build the heater
into bookcases, walls or enclosures (combustible
materials) without the use of a Mock Fireplace kit.
4. Due to high temperatures the room heater should be
located out of traffic and away from:
• Furniture and draperies
• Combustible materials
• Gasoline and other flammable liquids
Do not place clothing or other flammable
material on or near the heater.
5. Keep curtains*, clothes, furniture and other
flammable materials at least 900mm from front
and sides of heater.
* At the owner’s discretion curtain clearance can
be less than 900mm as long as they are restrained
from the front, top and sides of the heater.
The manufacturer takes no responsibility if curtain
clearance is less than 900mm and not restrained.
6. Children and adults should be alerted to the hazard
of high surface temperatures and should take care to
avoid burns or clothing ignition.
This appliance is not intended for use by
persons (including children) with reduced
physical, sensory or mental capabilities or lack
of experience and knowledge, unless they have
been given supervision or instruction concerning
use of the appliance by a person responsible for
their safety. Children should be supervised to
ensure that they do not play with the appliance.
DO NOT MODIFY THIS APPLIANCE.
9. If removed, the glass window must be put back onto
the unit prior to operating the heater.
10.Installation and repairs should be performed by
authorised personnel only; refer to back of manual
for service number.
Note: when installing into a mock fireplace a
mock fireplace installation kit must be used.
(Part No. MOCKKIT12)
11.The heater must be properly installed with a 100mm
diameter flue. Operation of this heater, when not
connected to a properly installed and maintained
flueing system, can result in carbon monoxide (CO)
poisoning and possible death.
12.Testing the effectiveness of the flue: before testing the
flue confirm air vents are unobstructed. If an extraction
system or other heating appliances are present switch
them on. This is to test that there is no interaction
between the Cannon heater and other appliances.
Refer to Australian Standard Gas Installations AS 5601.
For ‘air movement not to affect appliance’
For ‘air supply to appliance’
For ‘ventilation requirements’
13. On first lighting your heater, an odour and possibly
some harmless smoke may be emitted due to its new
condition. This is quite normal and will disappear after
a few hours use.
Important: When this heater is operating the mesh
guard/glass front is hot. The mesh guard, or glass
front, is fitted to this appliance to reduce the
risk of fire or injury from burns and no part of it
should be permanently removed. For protection of
young children or the infirm, a secondary guard is
recommended (not supplied with heater).
This appliance meets the following standards:
Standards Australia
AS/NZS 3100
AS/NZS 5601.1
AS 4553:2008
7. Never attempt to burn paper or any other material in
the heater.
8. DO NOT PLACE ARTICLES ON OR AGAINST THIS
APPLIANCE.
DO NOT USE OR STORE FLAMMABLE MATERIALS
NEAR THIS APPLIANCE.
Cannon Fitzroy / Canterbury Inbuilt | 5
OPERATION
•
Operating Instructions
Plug the power cord into the wall socket and turn on the
power to the heater (FIG 1). Alternatively, switch on the
isolation switch and circuit breaker at the main switchboard if the heater has fixed wiring. Refrain from using
an extension cord.
User controls FIG 2.
When there is power available to the heater and it is in
the OFF or Standby mode, a red LED located inside the
ON/OFF button will flash twice and will extinguish after
approximately 3 seconds and then repeat this
cycle continuously.
If there is an interruption to the power supply the
heater will fail safely and switch off. When the power
supply has been restored you MUST wait at least 5
minutes before turning the heater ON.
Cleaning
All cleaning should be carried out when the heater is
cold. Normally the heater should only need wiping with a
lint-free damp cloth. Any stubborn stains can be removed
with a nonabrasive spray on cleaner. If an abrasive
cleaner is used the paint finish will be damaged.
For heaters fitted with the glass front: all cleaning should
be carried out when the heater is cold. Clean the outer
To turn the heater ON press the ON/OFF button once.
glass with a mild liquid or spray or glass cleaner. Do not
• The LED will illuminate and an audible beep will sound use harsh abrasive cleaners or sharp metal scrapers to
clean the heater glass front since they can scratch the
but there will be approximately 5 seconds delay
surface, which may result in shattering of the glass.
before the ignition system commences. On successful ignition the heater will operate on Low Fire and
Internally the heater should only be cleaned by an
Low Fan for approximately 3 minutes then will switch authorised service person.
to selected setting (if already chosen, otherwise will
If your heater requires attention contact your supplier
switch to NORMAL setting automatically).
or an authorised service person.
• The LED will extinguish approximately 30 seconds
Flame Characteristics
following the ignition startup.
• Select the desired heating level by pressing the LOW, The heater flame should be stable, not lifting from the
burner. The logs should glow after approximately
NORMAL or BOOST button once as required.
15 minutes operation on BOOST setting.
• LOW is LOW heat and LOW speed fan. BOOST is
The heater is designed to operate with luminous flames
HIGH heat and HIGH speed fan.
and may exhibit slight carbon deposit on the logs. If there
• To turn the heater OFF press the ON/OFF button
is any excess carbon build-up on logs, or the burner
once. An audible beep will sound twice to indicate
flame is unstable, contact Sampford IXL in your state.
the heater is off. The burner will extinguish but the fan
will continue to operate for approximately 3 minutes.
Important
Remember that the fan will continue to operate for
The appliance MUST be serviced at least annually
approximately 3 minutes after the OFF button has
by authorised personnel. This maintenance cost is
been pressed but you can turn the heater ON again
not covered under the warranty terms and condiwithout having to wait for the fan to stop operating.
tions. More frequent cleaning may be required due
• If the ignition system fails to ignite or keep the burner to excessive lint build-up from carpeting, bedding
alight, the system will beep 4 times and go into
materials, pet hair, etc.
safe shutdown mode. It will beep 4 times every 30
It is imperative that control compartments, burners
seconds to alert you to the fact. Press the ON/OFF
and circulating air passage ways of the appliance
button once to restart the heater during this time.
be kept clean.
You MUST wait at least 5 minutes before trying to
Do not use this heater if the glass is cracked or with
turn the heater on again if there have been several
the safety screen removed.
attempts to ignite the heater without success.
Do not use heater with broken or missing logs.
ON / OFF
LOW
NORMAL
BOOST
FIG 1
6 | Cannon Fitzroy / Canterbury Inbuilt
FIG 2
High wind gusts can affect the heaters flueing and
switch the heater off. If this happens, restart the
heater as normal. If the problem persists contact
Sampford IXL.
OPTIONAL ACCESSORIES
Versatility and flexibility are key components of our
installation options. If installed into a shallow recess or an
existing fireplace, elegant spacers will eliminate any size
discrepancies. To enhance your Cannon’s appearance
add a decorative 3 or 4 sided surround.
For added convenience the heater can now be
connected to a home automation system, such as C-bus.
This allows the heater to be turned on or off remotely
(normal heat setting only). Speak to your home
automation specialist for further information.
Every Cannon heater brings you the optional convenience
of being controlled via a remote thermostat.
Flue kit 4m Ø100mm
Chimney plate
Product Codes
• Flue kit for inbuilt Canterbury and
Fitzroy heaters: IBFLUEKIT
• Chimney plate to fit Inbuilt flue kit:
IBFLUEPLATE
• 50 mm spacer kit
CANT model BSPACERE-B
FITZ Black BSPACERX-B
FITZ Platinum BSPACERX-P
Spacer kit
Fitzroy mesh guard
3 sided surround kit
• 3 sided surround kit:
CANT model
CANTSURROUND3SX-B (black)
FITZ models
FITZSURROUND3SX-B (black)
FITZSURROUND3SX-P (platinum)
FITZSURROUND3SX-S (S/Steel)
• Fitzroy freestanding kit:
FITZFSKITX-B
• Console Kit:
Fitzroy console kit:
Fitzroy freestanding kit
Console kit
Mock fireplace kit
CONSFITZX-B (black)
CONSFITZX-P (platinum)
Canterbury console kit:
CONSCANT-B (black)
• Mock fireplace kit
(all open flue inbuilts): MOCKKIT12
• 4 sided surround:
SURROUND4SX-B (black)
SURROUND4SX-P (platinum)
SURROUND4SX-S (stainless steel)
• Canterbury mesh kit: CANTIBMG-B
• Fitzroy mesh kit: FITZIBMG-B
• Remote Thermostat: RTKIT
4 sided surround kit
Canterbury mesh guard
Remote thermostat
Cannon Fitzroy / Canterbury Inbuilt | 7
FITZROY INBUILT SPECIFICATIONS
Cannon Fitzroy Inbuilt
Please Note:
• When installing into a mock fireplace a mock fireplace
installation kit must be used.
• The data label is located in the fan chamber.
Access by removing front fascia.
Gas type
Natural or Propane gas,
as indicated on data label
Gas consumption
26.0 MJ/hr
Energy output
5.65 kW / 20.34 MJ/hr
Energy star rating
3.60 stars
Heater type
Gas space heater approved to
AS 4553:2008
Operating pressure
Natural gas 0.75 kPa (High)
/0.40 kPa (Low)
Propane gas 2.65 kPa (High)
/ 1.1 kPa (Low)
Gas regulator
Integral part of controller
Min. inlet pressure
1.13 kPa (NG)
2.75 kPa (Propane)
Fan
3 speed
Ignition
Electronic direct spark
Power requirement
240 VAC 10 Amp
switch socket
Power consumption
90 VA maximum
Minimum cavity
dimensions
Height 605 mm*
Width 700 mm*
Depth 409 mm^*
Optional accessories
• Glass front
• Remote thermostat
• Spacer kit
• 3 sided surround
• 4 sided surround
• Console kit
• Freestanding kit
• Inbuilt flue kit
• Mock fireplace installation kit
Overall dimensions
Refer to FIG 3
^Minimum depth for heater and flue adaptor.
* For installation into masonry/brick fireplaces.
FIG 3 Front View and Side View of Fitzroy
8 | Cannon Fitzroy / Canterbury Inbuilt
CANTERBURY INBUILT SPECIFICATIONS
Cannon Canterbury Inbuilt
Please Note:
• When installing into a mock fireplace a mock
fireplace installation kit must be used.
• The data label is located in the fan chamber.
Access by removing lower fan chamber fascia panel.
Gas type
Natural or Propane gas, as
indicated on data label
Gas consumption
26 MJ/hr input
Energy output
5.10 kW / 18.36 MJ/hr
Energy star rating
3.1 stars
Heater type
Gas space heater approved to
AS4553:2008
Operating pressure
Natural gas: 0.75 kPa (High)
/0.40 kPa (Low)
Propane gas 2.65 kPa (High)
/ 1.1 kPa (Low)
Gas regulator
Integral part of controller
Min. inlet pressure
1.13 kPa (NG)
2.75 kPa (Propane)
Fan
3 speed
Ignition
Electronic direct spark
Power requirement
240 VAC 10 Amp
switch socket
Power consumption
90 VA maximum
Minimum cavity
dimensions
Height 640mm*
Width 710mm*
Depth 359mm^*
Optional accessories
• Safety mesh guard
• Remote thermostat
• Spacer kit
• 3 sided surround
• 4 sided surround
• Console kit
• Inbuilt flue kit
• Mock fireplace installation kit
Overall dimensions
Refer to FIG 4
^Minimum depth for heater and flue adaptor.
*For installation into a masonry/brick fireplace.
125 mm
850 mm
338 mm
630 mm
600 mm
655 mm
180 mm
41 mm
FIG 4 Front View and Side View of Canterbury
Cannon Fitzroy / Canterbury Inbuilt | 9
FITZROY & CANTERBURY INBUILT INSTALLATION INSTRUCTIONS
Overview
1. This appliance MUST be installed by an authorised
service person only.
2. This appliance shall be installed in accordance with
the manufacturer’s installation instructions, local gas
fitting regulations, municipal building codes, electrical
wiring regulations, and AS/NZS 5601.1 the Australian
Standard for Gas Installations.
3. Open top of carton and remove accessories (logs).
Lift carton up and remove. Remove the four transit
screws fixing the heater to the pallet. Check that the
heater is suitable for the gas available. Refer to the
data label located within the fan chamber (bottom
most area with fascia removed). (Please dispose of
packaging appropriately. Keep away from children).
Any service requests resulting from incorrect
installations are not covered by our warranty
terms and conditions and these calls will result in
charges, usually to the end user, so please ensure
that the installation and commissioning has been
satisfactorily carried out before calling for any
warranty service.
Please make sure that your customer is fully instructed on
how to operate the heater.
Clearances
For minimum clearances refer FIG 5 and FIG 6.
A clearance of 25 mm minimum must be maintained
between the flue and flue spigot and any
combustible surface.
Ensure the minimum clearances to combustible
materials are maintained during installation, including
Cannon heaters MUST be flued with an appropriate
adequate space for the proper operation and servicing
100mm diameter flue pipe. The reliance on the chimney
of the heater. For clearances to furniture and curtains
to provide effective flueing may result in poor combustion, refer to warning on page 5 (Safety Warnings).
CO (carbon monoxide) poisoning and possible death.
Note: Ensure that the combustion air opening under the
Installation Instructions
A solid, leveled and smooth base is required (fill gaps
with fibreglass insulation if necessary).
heater is not obstructed.
Install a chimney plate and cowl to the chimney opening
using weatherproof mortar to common building practice.
Ensure there are no obstructions around cowl, i.e.
overhanging tree branches.
Method of fixing to finished wall surface (plaster/
masonry/brick): suitable fixtures which are able to be
easily removed must be used.
Installation Into A Masonry/Brick Or Mock Fireplace
We recommend cleaning or sweeping the chimney and
Both models FITZIB & CANTIB can be installed into a
fireplace before the installation of the heater commences. masonry/brick fireplace or a mock fireplace. If installing
There MUST be a good seal around the heater, gas piping into a mock fireplace a mock fireplace installation kit
and electrical cable rear entry to stop any draught. Do not MUST be used. The mock fireplace kit can be ordered
use adhesives or silicone sealant, the heater MUST be
from the Cannon distributor. Order specifIcation for the
able to be easily removed if necessary.
part is ‘MOCKKIT12’.
Remove any curved fire wall that slopes too far forward
to the fireplace opening as it makes fitment of the flue
pipes diffIcult.
Make sure that the heater is fully commissioned and
be certain to conduct a test of the integrity of the flue
operation, taking into account any influences created by
range hoods, exhaust fans, central heating, etc. Refer
to Australian Standard Gas Installations AS/NZS 5601.1:
‘commissioning’.
To avoid any unnecessary delays and inconvenience to
your customer please contact our Technical Services
Department on 1300 727 421 if the installation is unusual
or you have concerns with the installation and/or heater
operation before the installation commences.
Refer to Australian Standard Gas Installations
AS/NZS 5601.1 for ‘location of flue terminal’
Terminating a flue in a roof space is not permitted.
For installation into a masonry or brick fireplace with
a flue connection, refer FIG 7. After installation of the
heater, test the flue to confirm air vents are unobstructed.
If an exhaust fan or other heating/ventilation appliances
are present, switch them on. This is to test and ensure
that there is no interaction between the Cannon heater
and other appliances.
Refer to Australian Standard Gas Installations AS/NZS
5601.1:
For ‘air movement not to affect appliance’.
For ‘air supply to appliance’.
For ‘ventilation requirements’.
Mock Fireplace Opening
(Combustible materials)*
Fitzroy Inbuilt
Canterbury Inbuilt
Max
Min
Max
Min
Height
640 mm
630 mm
640 mm
630 mm
Width
760 mm
731 mm
760 mm
731 mm
Depth
N/A
410 mm**
N/A
363 mm**
*If you have larger opening than the maximum height indicated, a surround kit is
recommended. **Includes 25mm clearance between flue spigot and rear wall
10 | Cannon Fitzroy / Canterbury Inbuilt
FITZROY & CANTERBURY INBUILT INSTALLATION INSTRUCTIONS
Ceiling
Note: X = 50mm for Non Combustible Surfaces
X = 100mm for Combustible Surfaces
710 - 760 mm
690 mm
X
690 mm
100 mm **
** Ensure controls are visible
FIG 5 FITZIB-SMENB / FITZIB-SMEXB / FITZIB-SMEXP
Ceiling
1000 mm min clearance
Mantle 300 mm min clearance
338 mm
100 mm
180 mm
Rear wall of
fireplace
25 mm min
522 mm
900 mm min clearance
Note: X = 50mm for Non Combustible Surfaces
X = 100mm for Combustible Surfaces
710 - 760 mm
690 mm
690 mm
X
100 mm **
** Ensure controls are visible
FIG 6 CANTIB-SDEEB
Cannon Fitzroy / Canterbury Inbuilt | 11
FITZROY & CANTERBURY INBUILT FLUEING
Flue installation
500mm between top of
cowl and nearest part of
roof. (Also refer to AS/
NZS 5601.1)
Please note: flueing of heater MUST be
carried out by an authorised person.
Refer to Australian Standard Gas
Installations AS/NZS 5601.1.
Flue cowl
approved to
AG604/
AS4566
Flue clamp
Roof cladding
Flashing
Installing a flue on the shorter wall may
subject it to down draughts or reverse
air flows through the heater which can
be difficult to find a solution to. Always
adopt correct flue design practices.
Refer to Australian Standard Gas
Installation AS/NZS 5601.1 for ‘location
of flue terminal’.
The heater has been tested and should
operate satisfactorily with an optimum
flue length of 4.5 meters.
Exceeding this length may affect the
stability of the flame pattern and the
operation of the heater. Contact our
Technical Support Department if any
further advice is required.
Fit two lengths of vertical flue (1.8m) before fitting
any 45° bends. If bends are used, fit inside of flue
pipe. Use no more than two 45° bends in the total
flue run and maintain at least 250mm of straight
flue pipe between the bends.
Ø100mm flue
The flue must be fixed in place.
Heater
Install heater
onto a solid,
leveled base.
FIG 7 This diagram is to be used as a general guide only.
12 | Cannon Fitzroy / Canterbury Inbuilt
Flue Adaptor
(supplied as standard)
FITZROY INBUILT FASCIA REMOVAL
1. Remove the outer glass by gently lifting it
upwards and then outwards. Similarly remove a fitted
wire mesh fascia by also gently lifting it upwards and
then outwards.
2. Remove 4 M5 screws fixing the fascia assembly to the
heater body. Bring the bottom of the fascia towards
you gently to partly disengage it from the body of the
heater. After it has been disengaged gently lift it up
vertically to completely disengage it from the body of
the heater. Refer FIG 8 & FIG 9.
FIG 8
Inner Glass Removal For Both FITZIB & CANTIB
To fully remove the
fascia, unclip the switch
cable from the cable
connector on the PCB
and unclip the cable from
the clipping points on
the rear of the fascia.
To remove the inner glass, loosen off all the clamp screws
and completely remove the one vertical side.
Try not to touch the front surface of the glass. To avoid
finger marks use suitable cloth. Remove the glass by
sliding the glass sideways out of the clamp and then
lifting out from the bottom. Place the glass in a safe
position for refit later.
FIG 9
CANTERBURY INBUILT FASCIA REMOVAL
1. To remove the inner fascia assembly undo two
screws in the upper flange as indicated in FIG 10.
Remove the inner fascia assembly by holding the
glass surround and firmly pull it towards you. Refer
FIG 11.
2. Remove the lower front cover by unscrewing two M5
screws through the air intake slots. Refer FIG 12. Unit
is fitted with electronic switches. Ensure that the cable
cannot be trapped when the heater is installed.
4. Remove the surround by pulling the lower section
towards you gently to partly disengage it from the
body of the heater, then gently lift it vertically to
completely disengage it. Refer FIG 14.
5. To fully remove the fascia, unclip the switch cable
from the PCB connector and unclip the cable from
the clipping points. The cable is routed through a
plastic grommet which will have to be removed from
the base plate. Refer FIG 15.
3. To remove the front heater surround, undo two screws
(one either side) from the bottom flange of
the front panel as indicated in FIG 13.
FIG 10
FIG 11
FIG 12
Grommet
Grommet
FIG 13
FIG 14
FIG 15
Cannon Fitzroy / Canterbury Inbuilt | 13
FIXING OF THE FASCIA
You MUST NOT fix the front fascia to the wall.
The front fascia shall only be fixed to the heater.
ELECTRICAL CONNECTION
Electrical Connection
This appliance is designed to operate on 240V AC power
supply. Failure to operate unit at correct supply voltage
may create unsafe conditions.
All fixed wiring MUST be installed by a suitably
qualified person and comply to the appropriate
electrical wiring rules.
Grommet
The heater is supplied with a flexible power cord with
a plug fitted. A 10 Amp switch socket MUST be located
within 1.5m of the heater. For installations where the
power point is located outside of the enclosure, locate
the power cord in the fascia cut out on the left or right
hand side as required.
For a power supply connection located inside the
enclosure run the power cord through the cord access
located on the rear panel by pushing the cord access
plate from the bottom. The rubber grommet that is fitted
over the cord must be located correctly in the cut out of
the cord access plate. Refer FIG 16.
Restore the cord access plate to the original position and
seal with an appropriate removable material. A suitable
double pole isolation switch MUST be installed
externally for servicing or emergency shut down
of the heater.
FIG 16
It is critical that the appliance is earthed and that
the active and neutral are not reversed. Issues
arising from incorrect electrical wiring at premises
will not be covered under warranty (including use
of extension cords). We recommend that the heater
is connected directly to a switch socket by its own
power cord. Refrain from using extension leads.
INSTALLING THE FLUE TRANSITION
Step 1
Remove the heater’s fascia (refer to page 13). Remove
the screw positioned on the front of the heater which
secures the flue transition and guiding bracket. Refer to
FIG 17.
Step 4
Replace the screw which was taken out in Step 1 and
secures the spigot to the heater. Refer to FIG 20.
Screw
Step 2
Take the flue transition off the heater and mount it in the
fireplace cavity. When adopting a rigid metal flue
installation, flue transition (refer to FIG 18.) and flue need
to be secured inside fireplace cavity. Alternatively if using
a flexible flue it is not necessary to fix flue transition,
however the flue transition and the flue shall at all times
FIG 17
be supported independently from appliance flue outlet.
Guiding
Where necessary maintain minimum clearances of 25mm
Bracket
from combustible surfaces.
FIG 18
Screw
Step 3
Using the guiding bracket, slide the heater into place
making sure that the spigot is positioned correctly. Refer
to FIG 19.
14 | Cannon Fitzroy / Canterbury Inbuilt
FIG 19
FIG 20
LOG INSTALLATION
1. The burner is contained within the burner chamber.
Refer FIG 21.
2. Carefully unpack the log set. Logs are numbered
as follows:
#1 - Left front log
#2 - Left back log
#3 - Right front log
#4 - Right back log
Position the four individually numbered logs in the
following order on the burner bed as shown in
FIG 22-25. The locating pins on burner bed must engage
with corresponding holes in the individual logs.
Burner in base of
burner chamber
FIG 21
a) Place log #1 into the 2 front left pins on the burner bed,
ensuring that the charring faces the front.
Refer FIG 22.
b) Place log #2 onto the 2 left back pins. Refer FIG 23.
c) Place log #3 on single right front pin, ensure fork
locates over log #2. Refer FIG 24.
FIG 22
FIG 23
FIG 24
FIG 25
d) Place log #4 on single right back pin, ensure left side
of log rests on depression in #3 log. Refer FIG 25.
3. Refit the inner glass, making sure not to over
tighten the screws.
4. Reconnect switch loom to the fascia switch set.
5. Refit the front fascia.
GAS CONNECTION
1. Push the gas inlet access plate into the heater cabinet 4. The heater MUST NOT be connected using a flexible
and slide the heater into the fireplace ensuring that the
hose.
gas inlet pipe is fed through the hole located at the rear
right hand side of the heater at the bottom.
Gas Inlet
Refer FIG 26.
2. With heater in position, flanges should be hard against
masonry. Secure case flanges to the masonry.
Screw or bolt the flange through the slots provided.
Solid copper
pipe to be
used only
Note: The appliance must be secured at the front to
a vertical face. Where this is difficult due to building
inaccuracies, limited non-combustible packing may be
used to obtain a suitable vertical surface. Method of
FIG 26
fixing to finished wall surface (plaster/masonry/brick)
suitable fixtures which are able to be easily removed
must be used.
35 mm
35 mm
3. Connect the gas supply pipe to the copper
compression fitting provided (we recommend using
a basin wrench). Push the gas inlet plate down to its
original position and seal with an appropriate easily
removable material. Do not seal with a silicone sealant
69 mm
as the heater must be easily removable. Sealing is
important as it prevents any leakage of flue products
into the room. Test all connections for gas leaks.
FIG 27 Fitzroy
½ inch compression
69 mm
FIG 28 Canterbury
Cannon Fitzroy / Canterbury Inbuilt | 15
SETTING THE GAS PRESSURE
1. Gas valve layout is as indicated in FIG 29.
Pressures for ‘Burner High Flame’ and ‘Burner Low
Flame’ are factory set, however if pressures need to be
checked or adjusted, follow the procedures described
below. To check outlet pressure at burner ‘High Flame’
and ‘Low Flame’ positions remove the plastic cap from
the regulator adjustment location as indicated
in FIG 30.
Burner adjustment (Burner
‘Low Flame’)
Pressure test point
with captive screw
Pressure adjustment (Burner ‘High
Flame’)
Plastic Cap
2. The pressure point is closed with a captive screw. Turn
screw 6 revolutions anticlockwise to open the pressure
point as indicated on FIG 31 (a) and place manometer FIG 29
tube over the test point as per FIG 31 (b).
3. Switch the control buttons to ‘High Flame’ position.
Wait for heater to switch to ‘BOOST’ setting (time
delay on start up). Retain screwdriver in position and
using a spanner adjust the outer nut on the control
to give a high pressure reading (refer to specification
tables on page 8 & 9). (Turn clockwise to increase
pressure and anticlockwise to decrease pressure).
Refer FIG 32.
4. Switch the control buttons to ‘Low Flame’ position.
Retain spanner in position and using a screwdriver
adjust the central screw control to give a pressure low
reading (refer to specification tables on page 8 & 9).
(Turn clockwise to increase pressure and
anticlockwise to decrease pressure).
Refer FIG 33.
FIG 30
5. Remove spanner and screwdriver. Switch from BOOST
to LOW to ensure settings are correct.
6. Switch heater off and remove the manometer
tube. Tighten pressure test point by
turning the captive screw fully clockwise.
(a)
(b)
FIG 31
7. Replace plastic cap. Ensure the little lug is positioned
towards lower right hand side to clear the controls.
Adjust
8. Refit the fascia, making sure not to damage the power
cord or switch cable.
9. Operate the heater on BOOST, NORMAL and LOW
settings. The flame should be stable, no lifting from the
burner and the logs should glow after approximately
15 minutes of operation on BOOST setting.
If the flame is unstable:
•
Check that the burner is located correctly.
•
Check that the glass front is located correctly and is
against the sealing rope.
•
Check that the gas pressure is correctly adjusted.
•
Check that flue is operating correctly.
Hold
FIG 32
Hold
If the heater still does not operate to specification refer
to the troubleshooting chart on pages 20 & 21, or contact
Sampford IXL in your state.
Adjust
FIG 33
16 | Cannon Fitzroy / Canterbury Inbuilt
SERVICE INSTRUCTIONS (DO NOT MODIFY THIS APPLIANCE)
General
1. Service work MUST be carried out by authorised
personnel only.
2. Unplug from wall socket or turn off power at
isolation switch if heater is hard wired.
3. Always shut off the gas supply and ensure that the
heater is cool before commencing any service
operations.
4. Always check for gas soundness after servicing.
To Replace Power Cord
Contact Sampford IXL service department.
To Replace The Gas Valve
1. Remove the fascia. Refer to page 13 of the
installation instructions.
2. Unplug the cable from the gas control and
disconnect the earth connection.
3. Disconnect the gas inlet (½” compression nut)
connection at entry gas control and the 16mm nut
at the outlet of the gas control.
4. Remove the three screws from the cradle retaining
the gas control.
5. Remove gas control valve from heater.
6. Replace gas control and check for gas tightness.
Note: Check the gas pressure on Boost and Low
settings. Refer “gas control”, page 16.
To Replace The Ignition Module
1. Remove the fascia. Refer to page 13 of the
installation manual.
2. Unplug wire connectors from ignition module.
3. Lift ignition module from base panel.
3. Lift electronic controller from base panel.
Note: Hook and loop mounting tape is used to secure
electronic controller.
4. Replace the electronic controller.
5. Check and re-set gas pressures.
To Replace The Inner Glass
Refer to page 13 of the installation instructions.
Fit the new glass.
Note: Ensure the inside surface of the glass is clean and
free from finger marks.
To Replace The Burner And Spark/Sense Electrodes
1. Remove the logs from the burner chamber. Refer to
page 15.
2. Remove the burner chamber front panel, 4 screws.
3. Disconnect the 16mm nut at the inlet of the injector.
4. Disconnect the spark and sense electrodes from the
ignition module.
5. Remove the 2 M5 wing nuts from under the burner.
Lift the burner assembly upwards and carefully
remove from the burner chamber. Refer to FIG 34.
6. Replace in reverse order, checking correct location
of spark/sense electrodes. Refer FIG 35. Spark gap
between electrode and spark plate is 6 - 8 mm.
Flame sense electrode MUST be in constant flame.
Check for gas tightness. For log placement, refer to
page 15 of this manual.
Note: Hook and loop mounting tape is used to secure
ignition box.
4. Replace ignition module and ensure that all wires
are reconnected correctly.
5. Check and re-set gas pressures.
To Replace The Electronic Controller
1. Remove the fascia. Refer to page 13 of the
installation manual.
2. Disconnect the plugs on electronic controller.
Room Fan Pressure Switch
FIG 34
Securing the burner bed
Flame Sense
Electrode
Room Fan
Spark Plate
Electronic Controller
FIG 33
Ignition Module
Spark Electrode
Gas Valve
FIG 35
Cannon Fitzroy / Canterbury Inbuilt | 17
NO
SPARK
ELECTRODE
IGNITION MODULE
F3833
EARTH
BLUE
RED
RED
MODULATING
VALVE F3590
1 WAY
FLAME
SENSOR
NATURALLY ASPIRATED
WIRING DIAGRAM
PRESSURE
SWITCH F3327
ROOM AIR FAN
C
NC
RED
3 WAY
2 WAY
4 WAY
2 WAY
ROOM FAN - F3594
240 V MAINS PLUG
COILS
EARTH
6 WAY
4 WAY
RED
BLUE
BLUE
BROWN
1.5 AMP[18]
PURPLE
GREY
ORANGE
RED
WHITE
BLACK
C
N
N
A
L
M
H
TH2
MOD2
MOD1
SHEATHED
HIGH TEMP
DATA CABLE
F3835 C
CONTROL
MODULE
F3828
HIGH BRN / HIGH FAN
MED BRN / MED FAN
LOW BRN / LOW FAN
ON/OFF
SWITCH
WIRING DIAGRAM
FIG 38
Cannon Fitzroy / Canterbury Inbuilt | 19
SERVICE INSTRUCTIONS (DO NOT MODIFY THIS APPLIANCE)
To Replace The Fan Pressure Switch
1. Remove the fascia. Refer to page 13 of the
installation instructions.
2. Remove the electronic controller. Refer to page
17.
3. Remove the connecting wiring from the pressure
switch.
4. Remove the silicone tubes from the pressure
switch.
5. The pressure switch is secured onto the rear of the
fan chamber housing by two M5 screws. Remove
the screws.
6. Replace the pressure switch. For wiring, one wire
to “C”(Common) and the other to connect to “NO”
(Normally Open). Polarity is not important.
7. Re-attach silicone tubes making sure that the
black tube attaches to the black side of the
pressure switch. Make sure that the tubes are not
pinched or kinked.
8. Test operation of fan pressure switch - turn heater
on low heat. If heater fails to light even when fan is
spinning, refer to the fault codes on page 20.
5. Remove the venturi and bracket from the fan
which was removed from the heater. Insert and
secure the venturi and bracket on replacement fan.
Note: “TOP” should point to air outlet of fan.
6. Insert fan into chamber ensuring that the venturi is
not disturbed. Locate fan onto male thread. Secure
with M5 wing nuts, ensuring rubber buffer locates
over thread.
7. Replace silicone tubes onto fan pressure switch
ensuring that the black tube is connected to the
black side of the pressure switch. Check to make
sure that the tubes are not kinked or pinche. Refer to
FIG 37.
8. Reconnect fan plug into plug carrier. Test operation
of room circulation fan and fan pressure switch. If
heater fails to light even when fan is spinning, refer
to fault codes on page 21.
Switch Control Setting (FIG 36)
For NG operation, DIL switch should be positioned in
point ‘1'.
For LPG operation, DIL switch should be positioned in
pointer ‘O’.
For audio beep function, DIL switch should be
positioned in pointer ‘2'.
To Replace The Room Circulation Fan
1. Remove the fascia. Refer to page 13 of the
installation instructions.
2. Remove the electronic controller and ignition
module. Refer to page 17.
3. Disconnect the fan plug from the plug carrier.
Remove the two M5 wing nuts which locate the fan
to the fan chamber underside. Lower fan from
male thread.
4. Disconnect the silicone tubes from the fan
pressure switch. Remove fan from fan chamber.
GAS
NG
1
O
LPG
ON
2
N
OFF
Clear Silicon
Tube
BEEP
Black Silicon Tube
FIG 36
Switch Control Diagram highlighting NG/LP settings &
audible beep.
18 | Cannon Fitzroy / Canterbury Inbuilt
FIG 37
Room Fan
TROUBLESHOOTING
To check the operation of the heater’s electrical system
you will require a digital multimeter with the functions to
measure AC/DC voltage, continuity, resistance and
micro-amps.
It is critical that the appliance is
earthed and that the active and
neutral are not reversed.
Cannon Fitzroy and Canterbury Inbuilt
There is a green and red LED on the ignition controller. These LEDs act as diagnostic aids when the heater safety
systems produce a safe shutdown condition.
Green LED: this is on when the flame is sensed at the flame sensor electrode.
Red LED: this flashes according to the fault code.
No LEDs means there is no power to the ignition module. Check that the heater switch is set to ON by pressing the
ON/OFF button. Check the supply voltage. Check the 1.5 Amp fuse, replace if necessary. It is critical that the appliance
is earthed and that the active and neutral are not reversed. Do not use an extension cord. This appliance is designed
to operate at 240V AC. Substantial voltage dips, or running the unit at voltages substantially lower than 240V AC may
cause nuisance shutdowns. If there is still a problem check the power supply plug from the electronic controller with a
multimeter (240V AC). If there is no power from this plug when the heater should be on, replace the electronic controller.
Remember to re-test the gas pressures any time that the electronic controller is changed. It is recommended that any
callout to a customer’s h ome should prompt the checking and resetting of the gas pressures.
Fault Codes
Long Short Morse Code
Meaning
1
—
Normal operation
— —•
Check the gas supply to the unit is not switched off. Check
the gas pressures. Check the flame and spark electrode
connections and that they are positioned correctly. Ensure
Heater has attempted that the spark is being produced at the spark electrode
to light, however it did tip, and is strong (clearly visible and around 6-8mm in
not sense flame within length). Adjust if necessary. The burner tray is earthed
the allowed time.
through contact with the chassis. Check using a multimeter
between the earth pin (or earth tab) and the burner tray.
If the unit continues to spark after flame is present, ensure
that the supply voltage polarity is not reversed.
— —••
Flame was established,
however the flame
electrode has sensed
that the flame has
become unstable and
has shutdown the gas.
—••
Check the fan for dust build up and lint. Check that the
room air fan is spinning. Check that the pressure tubes are
connected correctly and not pinched or kinked. The black
tube should run from the black side of the pressure switch
Room fan (circulation to the bottom tapping on the fan venturi. The clear tube
fan) pressure signal not should go from the light side of the pressure switch and to
detected.
the top tapping on the venturi. Make sure that the pressure
switch wires are connected correctly. One wire should be
to C (Common) and the other should be to NO (Normally
Open). If it still doesn’t work after checking the above,
change the pressure switch.
2
2
1
0
1
2
2
20 | Cannon Fitzroy / Canterbury Inbuilt
Action
Check that the flame sense electrode and the spark
plate are correctly positioned. Check the flame sense
connections. Check that the flue is correctly constructed.
Abnormally strong downdrafts can cause flame instability
therefore it is recommended that an appropriate flue cowl
is used for windy areas. Improper gas pressures can also
cause issues. Check the gas pressures.
TROUBLESHOOTING
Fault Codes Continued
Long Short Morse Code
3
2
1
8
Meaning
Action
— — —•
Room fan (circulation
fan) pressure signal
has been interrupted.
Check the fan for dust build up and lint. Check that the
room air fan is spinning. Check that the pressure tubes are
connected correctly and not pinched or kinked. The black
tube should run from the black side of the pressure switch
to the bottom tapping on the fan venturi. The clear tube
should go from the light side of the pressure switch and to
the top tapping on the venturi. Make sure that the pressure
switch wires are connected correctly. One wire should be
to C (Common) and the other should be to NO (Normally
Open). If it still doesn’t work after checking the above,
change the pressure switch.
— —••••••••
Check the fan for dust build up and lint. Check that the
room air fan is spinning. Check that the pressure tubes are
connected correctly and not pinched or kinked. The black
tube should run from the black side of the pressure switch
Room fan (circulation
to the bottom tapping on the fan venturi. The clear tube
fan) pressure switch
should go from the light side of the pressure switch and to
has not switched within
the top tapping on the venturi. Make sure that the pressure
the expected time.
switch wires are connected correctly. One wire should be
to C (Common) and the other should be to NO (Normally
Open). If it still doesn’t work after checking the above,
change the pressure switch.
Other Possible Faults
No gas to burner.
• The gas valve should open at the same time as the igniter sparks.
If there is no gas to the burner when this occurs check the
solenoid coils for continuity.
• Check that the gas pressure is present at the test point when the
spark is being generated.
• Check that there is gas to the inlet of the gas control.
Fuse blowing.
• If the fuse continues to blow check the solenoid coils for a signs of
them being shorted.
• Check the fan and wiring for short circuit.
Cannon Fitzroy / Canterbury Inbuilt | 21
NOTES
22 | Cannon Fitzroy / Canterbury Inbuilt
NOTES
Cannon Fitzroy / Canterbury Inbuilt | 23
COPY RATING LABEL HERE
Don’t Risk Your Appliance Warranty
Only a licensed person will give you a compliance certifIcate, showing that the work complies
with all the relevant standards. And only a licensed person will have insurance protecting their
workmanship for 6 years. So make sure you use a licensed person to install this appliance and ask
for your compliance certifIcate to ensure the manufacturers appliance warranty will be honoured.
Date Installed:
Compliance CertifIcate No:
Installed By:
GMK 10025
GMK 10112
AS4553:2008
Part Number:
F3841_E
24 | Cannon Fitzroy / Canterbury Inbuilt
For service to this appliance or spare parts
contact the CANNON distributor:
Sampford IXL – Spare Parts
Phone: 1300 727 421
Fax: 1300 727 425
Email: [email protected]
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertisement