Setup guide - Extron Electronics

Setup guide - Extron Electronics
Setup Guide ­— CSVEQ 100 D
This guide provides basic instructions for an
experienced installer to set up and operate the
Extron® CSVEQ 100 D Line Driver.
C Installation and service must be performed
by authorized personnel only.
Step 1 — Turn off the line driver and
input/output devices
Front panel
Turn the input and output devices off and unplug
their power cords. Verify that the line driver
is disconnected from the power source before
proceeding.
Wall Plate
Power
LED
Faceplate
1
VIDEO IN
S-VIDEO
IN
S-video
3 Input
2
Step 2 — Attach video output cables
RCA
Video
Input
• Connect a composite video output device to the
green cable ( ).
g
AUDIO IN
L
R
Audio
4 Input
• Connect the luma of an S-video output device to
the white cable ( ).
g
• Connect the chroma of an S-video output device
to the yellow cable ( ).
g
Rear panel
Step 3 — Attach video input cables
• Connect a composite video input source to the
RCA video input connector ( ).
b
• For audio output, wire a balanced or
unbalanced audio output device to the
3.5 mm, 5-pole, direct insertion captive
screw connector ( ). See figure 3 for
information on how to wire the audio
output connector.
The audio output
wiring and the audio
output jumper ( )
setting must match. For best results,
wire the output for
balanced audio.
f
Tip (L)
Ring (R)
C
EQ
GAIN
8
Audio
9
Output
Figure 1 – Front and rear panel view
Balanced Stereo
Unbalanced Stereo
Set audio output jumper to stereo.
Left Tip (+)
Sleeve
Right Tip (+)
AUDIO
OUTPUT
CONFIG
AUDIO
OUTPUT
CONFIG
JUMPER POSITION
OFF = DUAL MONO
ON = STEREO
JUMPER POSITION
OFF = DUAL MONO
ON = STEREO
Use either the left or the right channel.
Set audio output jumper to dual mono.
Use either the left or the right channel.
Set audio output jumper to dual mono.
Balanced Mono
Tip (+)
Ring (-)
Sleeve
Unbalanced Mono
Tip (+)
AUDIO
OUTPUT
CONFIG
JUMPER POSITION
OFF = DUAL MONO
ON = STEREO
Sleeve
CAUTION Connect the sleeve to ground
Sleeve ( )
Figure 2 – Audio input
wiring
5
Power
Connector
Set audio output jumper to stereo.
Left Tip (+)
Left Ring (-)
Sleeve (s)
Right Tip (+)
Right Ring (-)
Y
VIDEO
AUDIO
OUTPUT
CONFIG
JUMPER POSITION
OFF = DUAL MONO
ON = STEREO
AUDIO OUTPUT
• For audio input, connect an unbalanced
stereo audio source to the left and right
RCA connectors ( ). Wire the connector
as shown in figure 2.
N
Audio
Output
Jumper 6
Video
7
Output
i
d
VIDEO
OUTPUT
Step 4 — Connect audio input/output
GAIN
c
Equalization
and Gain
Controls
GAIN
CSVEQ 100 D
EQ
• Connect an S-video input source to this 4-pin
mini DIN connector ( ).
Do not tin the wires!
AUDIO
OUTPUT
CONFIG
JUMPER POSITION
OFF = DUAL MONO
ON = STEREO
(Gnd). Connecting the sleeve to
a negative (–) terminal will
damage the audio output
circuits.
Figure 3 – Audio output wiring
Setup Guide ­— CSVEQ 100 D (cont’d)
Step 5 — Power on the line driver and input/output devices
h).
Wire the power supply (see figure 4) and connect it to the power connector (
power is applied to the unit, the front panel LED ( ) lights.
a
Connect the power cords of the input and
output devices and turn them on. The
picture should appear and sound should be
audible.
When
Ridges
Smooth
A
A
3/16”
(5 mm) Max.
SECTION A–A
C Always use a power supply
Captive Screw
Power Supply
supplied by or specified by
Connector
Output Cord
Extron. Use of an unauthorized
Figure
4
–
Power
supply
wiring
power supply voids all regulatory
compliance certification and may cause damage to the supply and the end product. Unless otherwise stated, the AC/DC adapters are not suitable for use in air handling
spaces or in wall cavities. The installation must always be in accordance with the
applicable provisions of National Electrical Code ANSI/NFPA 70, article 75 and
the Canadian Electrical Code part 1, section 16. The power supply shall not be
permanently fixed to building structure or similar structure.
This product is intended to be supplied by a Listed Power Unit marked “Class 2” or
“LPS”, rated 12 VDC, 1 A minimum.
Step 6 — Adjust video gain and equalization
e
While watching the display, adjust the video gain and equalization ( ) by using
the rotary gain and equalization (EQ) control potentiometers (see figure 5). Make all
adjustments using a small screwdriver. For
a more precise setting, use an oscilloscope
or a waveform monitor connected to the far
end of the output cable.
Figure 5 – Equalization and gain controls
If using very short output cables:
• Set all potentiometers to the default setting (the arrow on the control pointing to the dot
beside it, as shown in figure 5).
If using longer output cables:
• Supply the color bars test signal to the input (Recommendation: use an Extron VTG 300
Video Test Generator to generate the test signal).
• Adjust the gain controls for the output until the signal level at the far end is the same
as the input (or the display shows the
correct brightness and contrast).
Extron
• Adjust the EQ control for the output
so that no overshoot or round front
corner appears at the far end on the
oscilloscope or you see a sharp picture
with no smearing.
MPA 152
Stereo Power
Amplifier
UT
TP
15
INP
ED
LIST
IDEO
17TTIO/VTUS
AUDARA
Two-Way Ceiling
Speakers
R
TE
L
MO
RE
E
MUT
VOL/ A
50m
S
UT
US
C
ING
2 WIR ND
SS GROU
CLANOT RT TS!
SHO TPU
DO OR OU
R
AKE
SPE
Extron
SI 26X
4/8 S
OHM
OU
2
MPA
R
10V
L
APP
R
R
WE
PO
L
X
12VMA
3A
Balanced
Audio
Extron
CSVEQ 100 D
S-video
Step 7 — Mount the line driver
Make any cabling adjustments before
mounting the line driver as the cables may
be inaccessible afterwards. Mount the line
driver. For mounting information, see
“Installing the CSVEQ 100 D” in the
CSVEQ 100 D User’s Manual.
Extron USA - West
Headquarters
+800.633.9876
Inside USA / Canada Only
+1.714.491.1500
+1.714.491.1517 FAX
Projector
Composite
Video
1,000 Feet
EO
EO
S-VID
IN
VID
DIO
IN
IN
Composite Video, S-Video,
and Audio Line Driver
-R
AU
L -
DVD/VCR
Combo
Figure 6 – Application example
Extron USA - East
Extron Europe
Extron Asia
Extron Japan
Extron China
Extron Middle East
+800.633.9876
+800.3987.6673
+800.7339.8766
+81.3.3511.7655
+81.3.3511.7656 FAX
+400.883.1568
+971.4.2991800
+971.4.2991880 FAX
+1.919.863.1794
+1.919.863.1797 FAX
+31.33.453.4040
+31.33.453.4050 FAX
+65.6383.4400
+65.6383.4664 FAX
Inside USA / Canada Only
Inside Europe Only
Inside Asia Only
© 2010 Extron Electronics. All rights reserved.
Inside China Only
+86.21.3760.1568
+86.21.3760.1566 FAX
68-1598-50
Rev. A
03 10
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertisement