AutoDome 600 Series Analog PTZ Camera

AutoDome 600 Series Analog PTZ Camera
AutoDome 600 Series Analog PTZ
Camera
VG5 600 Series
en
User Manual
AutoDome 600 Series Analog PTZ Camera
Table of Contents | en
3
Table of Contents
1
Getting Started
5
1.1
Powering On
5
1.2
Establishing AutoDome Control
5
1.2.1
Basic Keyboard Operation
6
1.2.2
Keyboard Commands
6
1.3
Setting the Camera Address
7
1.3.1
FastAddress
7
1.4
Setting Passwords
8
1.4.1
Special Passwords
8
2
On-Screen Display Menu Navigation
9
2.1
Setup Menu
2.2
Camera Setup Menu
10
2.3
Lens Setup
12
2.4
PTZ Setup Menu
13
2.5
Display Setup Menu
15
2.6
Communication Setup Menu
16
2.7
Alarm I/O Setup
17
2.8
Rule Setup Menu
19
2.9
Language Menu
21
2.10
Advanced Feature Setup Menu
21
2.11
Diagnostics Menu
22
2.11.1
Alarm Status Submenu
24
3
Common AutoDome User Commands (unlocked)
25
3.1
Setting AutoPan Mode
25
3.2
Setting Preset Shots
25
3.3
Specifying a Shot or a Sector Title
26
3.4
Configuring Preposition Tours
26
3.5
Programming the Inactivity Operation
27
3.6
Recording Tours
27
4
Alternative Control Protocols
28
4.1
Setting FastAddress with Alternative Protocols
28
4.1.1
Using an American Dynamics Controller
28
4.1.2
Using a Pelco Controller
31
4.2
Pelco Protocol Mode
32
4.2.1
Hardware Configuration
32
4.2.2
Pelco Keyboard Commands
33
4.2.3
Pelco Keyboard Commands
33
4.2.4
Special Preset Commands
34
Bosch Security Systems, Inc.
9
User Manual
F.01U.215.781 | 1.0 | 2011.04
4
en | Table of Contents
AutoDome 600 Series Analog PTZ Camera
5
Pelco On-Screen Menus
35
5.1
Setup Menu
35
5.1.1
Command Lock (locked)
36
5.1.2
Bosch Menu (locked)
36
5.1.3
PTZ Setup (unlocked)
37
5.1.4
Other Menus
38
6
Keyboard Commands by Number
39
7
Advanced Features
42
7.1
Alarm Rules
42
7.1.1
Controlling Alarm Rules
42
7.1.2
Alarm Rule Examples
42
7.2
AutoTrack Operation
46
7.2.1
AutoTrack Settings and Recommendations
46
7.2.2
AutoTrack Optimization
47
7.3
Virtual Masking
48
7.4
Privacy Masking
48
7.5
Motion Detection with Region of Interest (Preset positions 90 through 99)
49
7.6
Image Stabilization
49
7.7
Pre-position Tour
49
7.8
Azimuth, Elevation, and Compass Directions
50
7.8.1
Setting the Azimuth Zero Point
50
7.8.2
Displaying Azimuth, Elevation, and Compass Headings
51
8
Troubleshooting Guide
52
8.1
VG5 AutoDome Operation and Control
52
8.2
VG5 Series AutoDome Audio
56
9
User Command Table
59
A
Appendix: FastAddress Conversions
61
Index
62
F.01U.215.781 | 1.0 | 2011.04
User Manual
Bosch Security Systems, Inc.
AutoDome 600 Series Analog PTZ Camera
1
Getting Started | en
5
Getting Started
Install and wire the AutoDome according to the VG5 AutoDome Installation Manual. A typical
system includes a keyboard, matrix switcher, monitor, and appropriate wiring connections.
Please refer to the individual product manuals for complete installation and setup instructions
for each of the system components.
1.1
Powering On
When you turn the AutoDome power on there is a ten (10) second pause before the dome
starts its homing phase. During the homing phase the camera pans left and right and tilts up
and down. It also adjusts the lens focus. The entire homing phase lasts approximately 40
seconds and ends with a splash screen.
Bosch Security Sys. AutoDome(r)
600 Series
Day/Night 36X
5.00.00.03/1.05.00.02
1.00.00.00
5.00.00.03
1.13.01.05
1.02.00.01
SC Boot
FPGA
VCA_boot
STD Comm
No Heater
FastAddress: Not Set
Figure 1.1
Sample VG5 Startup Splash Screen
The splash screen displays the type of AutoDome, the camera installed, the firmware levels for
various files, and the current IP address (for VG5 AutoDome 700 Series models).
1.2
Establishing AutoDome Control
The most common ways to interface with the AutoDome are:
–
Using a keyboard and on-screen display (OSD) menus. This method is the most common
and is covered in this manual.
–
Using the AutoDome Configuration Tool software running on a PC with Bilinx or the RS232/485 communication protocol. Refer to the CTFID User Manual for instructions.
–
Using a PC-based graphical user interface (GUI) such as the Bosch DiBos 8 software.
Refer to the DiBos 8 User Guide for instructions.
Bosch Security Systems, Inc.
User Manual
F.01U.215.781 | 1.0 | 2011.04
6
en | Getting Started
1.2.1
AutoDome 600 Series Analog PTZ Camera
Basic Keyboard Operation
The following tables summarize the basic operations for a standard keyboard and the
functions available to control an AutoDome camera.
Typical Keyboard
Usage
Features
Function Keys
Selects a specific control setting.
Number Keys
Inputs a number from 0 to 9.
Camera Key
Selects a camera number.
Enter Key
Inputs a selection.
Focus Key
Sets the lens focus or makes a menu selection in OSD mode.
Iris Key
Sets the lens iris setting or makes a menu selection in OSD mode.
Key LEDs
Indicates an active key.
LCD
Displays the current status.
Joystick
Controls a pan/tilt/zoom (PTZ) AutoDome camera.
Table 1.1
Dome Operation
How to control
To Pan Side to Side
Move the joystick left or right.
To Tilt Up and Down
Move the joystick forward and back.
To Zoom In
Twist the joystick clockwise.
To Zoom Out
Twist the joystick counterclockwise.
Table 1.2
1.2.2
Typical Keyboard Functions
Typical Keyboard Controls for an AutoDome Camera
Keyboard Commands
Keyboard control commands are composed of a sequence of three (3) inputs with the
following convention: 1) a Function key + 2) a Command number key(s) + 3) the Enter key.
–
Depending on the type of keyboard, the control function keys are labeled:
ON or AUX ON
OFF or AUX OFF
SET or SET SHOT
SHOT or SHOW SHOT
NOTICE!
The convention used for control key commands in this manual is ON, OFF, SET, and SHOT.
Refer to your keyboard manual for the key naming conventions.
–
Command numbers range from 1 to 999. See Section 6 Keyboard Commands by Number,
page 39 for a complete list of keyboard commands.
–
The Enter key can also be labeled with the 8? symbol.
For example, the keyboard command to make the AutoDome pan 360º continuously is:
ON-1-ENTER (press the ON key, then press the number 1 key, and then press ENTER.)
F.01U.215.781 | 1.0 | 2011.04
User Manual
Bosch Security Systems, Inc.
AutoDome 600 Series Analog PTZ Camera
1.3
Getting Started | en
7
Setting the Camera Address
Once the AutoDome power is turned on and homing is complete, you must set the camera
address. You may also want to assign a password and customize some of the AutoDome
default settings.
NOTICE! You do not need to set a camera address if using Bilinx or Ethernet communication.
See the VG5 AutoDome Installation Manual to configure an AutoDome for Bilinx or Ethernet
operation.
1.3.1
FastAddress
FastAddress is an AutoDome feature that allows you to set or change a camera address using
the keyboard and on-screen menus.
There are three (3) FastAddress commands:
–
ON-999-ENTER: Displays and programs all cameras without an address in the system.
NOTICE! If a keyboard is set to a camera number that already has an address, that camera
also responds to this command.
–
ON-998-ENTER: Displays and programs all cameras with or without an address in the
system.
–
ON-997-ENTER: Displays the current address status of all cameras in the system
simultaneously.
To set an address for a camera without an address:
1.
Select the camera number you want to FastAddress. The system displays the camera
number on the keyboard and the image on the corresponding monitor.
2.
3.
Press #-ENTER (where # is the camera number without an address).
Press ON-999-ENTER to invoke an on-screen display of cameras on the system without
an address.
4.
Follow the on-screen instructions. You receive an on-screen confirmation when the
FastAddress is complete.
To change or clear an address for a camera with an address:
1.
Select the camera number you want to FastAddress. The system displays the camera
number on the keyboard and the image on the corresponding monitor.
2.
3.
Press #-ENTER (where # is the camera number with an address).
Press ON-998-ENTER to invoke an on-screen display of all cameras on the system, with or
without an address.
4.
Follow the on screen instructions. You receive an on-screen confirmation when the
FastAddress is complete.
NOTICE!
FastAddress is stored in nonvolatile memory and does not change if the power is turned off or
if the default settings are restored.
Bosch Security Systems, Inc.
User Manual
F.01U.215.781 | 1.0 | 2011.04
8
en | Getting Started
1.4
AutoDome 600 Series Analog PTZ Camera
Setting Passwords
Passwords are used to control access to locked command menus. Unlocked commands are
available to all users. Passwords are four (4) digits in length.
1.4.1
Special Passwords
Password
Security Level
0000 (default)
Enables security and requires a user to enter the unlock command
OFF-90-ENTER before invoking a locked command.
9999
Disables all security and allows all users to access locked commands.
To set or change a password (locked command):
1.
Press OFF-90-ENTER to turn off the command lock.
2.
Press SET-802-ENTER to access the password menu.
3.
Tilt the joystick up or down to choose a number. Tilt the joystick right to move to the next
number position.
4.
Follow the on-screen instructions and save the password. You receive an on-screen
confirmation.
F.01U.215.781 | 1.0 | 2011.04
User Manual
Bosch Security Systems, Inc.
AutoDome 600 Series Analog PTZ Camera
2
On-Screen Display Menu Navigation | en
9
On-Screen Display Menu Navigation
The AutoDome is programmed through the on-screen display (OSD) menus. To access the
OSD menus, you must open the main Setup Menu.
Menu items marked with an asterisk (*) are default settings, unless otherwise noted.
NOTICE!
After a period of 4.5 minutes of inactivity, a menu times-out and exits without warning. Some
unsaved settings in the current menu can be lost.
2.1
Setup Menu
The main Setup Menu provides access to all programmable AutoDome settings. It is a locked
menu that requires the user to turn off the command lock.
To open the main Setup Menu (locked command):
1.
Press OFF-90-ENTER to turn off the command lock.
2.
Press ON-46-ENTER to access the Main Menu.
3.
Use the joystick to highlight a menu item.
4.
Press Focus/Iris to open a menu.
5.
Follow the on-screen instructions.
NOTICE!
The AutoDome displays only those menus applicable to the particular AutoDome Series
configuration. Use the joystick to navigate through the menu and the Focus/Iris keys to make
a selection.
Setup Menu
Exit...
Camera Setup
Lens Setup
PTZ Setup
Display Setup
Communication Setup
Alarm Setup
Language
Advanced
Diagnostics
Focus / Iris: Select
Setup Menu Choices:
Menu
Description
Exit
Exits the menu.
Camera Setup
Accesses adjustable camera settings such as: white balance, gain,
sharpness, sync, line lock, backlight, shutter, and night mode.
Lens Setup
Accesses adjustable lens settings such as: focus, iris, zoom speed, and
digital zoom.
PTZ Setup
Accesses adjustable pan/tilt/zoom (PTZ) settings such as: Autopan, tours,
PTZ speed, inactivity period, AutoPivot, and tilt limits.
Bosch Security Systems, Inc.
User Manual
F.01U.215.781 | 1.0 | 2011.04
10
en | On-Screen Display Menu Navigation
AutoDome 600 Series Analog PTZ Camera
Menu
Description
Display Setup
Accesses adjustable display settings such as: OSD, sector blanking, and
privacy masking.
Communication Accesses communication settings such as: AutoBaud and Bilinx.
Setup
Alarm Setup
Accesses the alarm settings such as: inputs, outputs, and rules.
Language
Displays the language.
Advanced
Accesses the advanced features menu including Stabilization, AutoTrack
Sensitivity, Camera Height, and Virtual Masking.
Diagnostics
Displays the status of diagnostic events.
NOTICE!
To select the Exit Menu item from anywhere in the current menu, use the Zoom command.
2.2
Camera Setup Menu
The Camera Setup Menu provides access to camera settings that can be changed or
customized. Menu items marked with an asterisk (*) are the default settings.
Camera Setup
Exit...
* White Bal:
EXT ATW
* Gain Control:
AUTO
* Max. Gain Level:
6 (4**)
* Sharpness
12
* Synch Mode:
Internal
* Line Lock Delay:
0
* Backlight Comp:
OFF
* WDR
OFF
* Shutter Mode:
Auto SensUP
* Shutter:
1/60
* Auto SensUP Max:
15x
* Night Mode:
AUTO
* Night Mode Color:
OFF
* Night Mode Threshold:
55
* Pre-Comp
1
Restore Defaults...
* = Factory Setting
** = WDR camera only
Focus / Iris: Select
F.01U.215.781 | 1.0 | 2011.04
User Manual
Bosch Security Systems, Inc.
AutoDome 600 Series Analog PTZ Camera
On-Screen Display Menu Navigation | en
11
Camera Setup Menu Choices:
Menu
Description
Sub-menu / Description
Default
Setting
Exit
Exits the menu.
White Balance
Maintains proper color reproduction
Extended ATW: Adjusts camera color
Extended
as the color temperature of a scene
using extended range.
ATW
changes. For example, from daylight
ATW: Adjusts camera color constantly.
to fluorescent lighting.
Indoor W.B.: Optimizes camera color for
typical indoor conditions.
Outdoor W.B.: Optimizes camera color for
typical outdoor conditions.
AWB Hold: Sets the camera's color
settings for the current scene.
Manual: Allows a user to adjust the Red
and Blue gain.
Sliding scale: – (1 to 100) +
Outdoor Auto: Automatically adjusts the
white balance to reduce the dark tones at
dawn or dusk.
Sodium Lamp: Optimizes the sodium vapor
light to restore objects to their original
color.
Sodium Lamp Auto: Automatically adjusts
for sodium vapor light to restore objects to
their original color.
Gain Control
Electronically brightens darker scenes
Auto or OFF
AUTO
Sliding scale:
4
which may cause graininess in low
light scenes.
Max. Gain Level Adjusts the maximum gain level that
the gain control adjusts to when set to
– (1 to 6) +
AUTO.
(1=8db, 2=12db, 3=16db, 4=20db, 5=24db,
6=28db)
Sharpness
Synch Mode
Adjusts the sharpness level of the
Sliding scale:
picture.
– (1 to 16) +
12
Sets the type of synchronization mode
INTERNAL: Synchronizes camera to an
for the camera.
internal crystal. This choice is
INTERNAL
recommended if there is noise on the
power line.
LINE LOCK: Synchronizes camera to AC
power. This choice eliminates picture roll
in multi-camera systems.
Line Lock Delay
Optimizes the LINE LOCK mode to
Sliding scale:
eliminate picture roll in multiphase
– (0º to 359º) +
0º
power applications.
Backlight Comp
Improves image quality when the
On or OFF
OFF
ON, OFF, or Auto
OFF
background illumination level is high.
WDR
Turns the wide dynamic range feature
on or off.
Bosch Security Systems, Inc.
User Manual
F.01U.215.781 | 1.0 | 2011.04
12
en | On-Screen Display Menu Navigation
Menu
AutoDome 600 Series Analog PTZ Camera
Description
Sub-menu / Description
Default
Setting
Shutter Mode
Turns Auto SensUP on or off.
Auto SensUP or OFF
Auto
SensUP
Shutter
Adjusts the electronic shutter speed
Sliding scale:
1/60 sec.
(AES).
– (60 at extreme left to 1/10000) +
(NTSC) or
1/50 sec.
(PAL)
Auto SensUP
Sets the limit for sensitivity when the
Max.
shutter speed is set to Auto SensUP.
Night Mode
Selects night mode (B/W) to enhance
15x, 7.5x, 4x, or 2x
15x
ON, OFF, or AUTO
AUTO
ON or OFF
OFF
55
lighting in low light scenes.
Night Mode
Determines if color processing
Color
remains in effect while in night mode.
Night Mode
Adjusts the level of light at which the
Sliding scale:
Threshold
camera automatically switches out of
–(10 to 55)+
night mode (B/W) operation.
(in increments of 5)
10 is earlier, 55 is later
Pre-Comp
Amplifies the video gain to
Sliding scale:
compensate for long distance cable
–(1 to 10)+
1
runs.
Restore
Restores all default settings for this
Defaults
menu only.
2.3
Lens Setup
The Lens Setup Menu provides access to lens settings that can be changed or customized.
Menu items marked with an asterisk (*) are the default settings.
Lens Setup
*
*
*
*
*
*
*
Exit...
Auto Focus:
Auto Iris:
Auto Iris Level:
Focus Speed:
Iris Speed:
Max Zoom Speed:
Digital Zoom:
Restore Defaults
SPOT
CONSTANT
8
2
5
FAST
ON
* = Factory Setting
Focus / Iris: Select
F.01U.215.781 | 1.0 | 2011.04
User Manual
Bosch Security Systems, Inc.
AutoDome 600 Series Analog PTZ Camera
On-Screen Display Menu Navigation | en
13
Lens Setup Menu Choices:
Menu
Description
Sub-menu / Description
Default
Setting
Exit
Saves and exits the menu.
Auto Focus
Automatically focuses on the
CONSTANT: Auto Focus is always active, even
subject in the center of the
while the camera is moving.
screen.
MANUAL: Auto Focus is inactive; manual focus
SPOT
must be used.
SPOT: The camera activates Auto Focus after the
camera stops movement. Once focused, Auto
Focus is inactive until the camera moves again.
Auto Iris
Auto Iris Level
Focus Speed
Iris Speed
Automatically adjusts to
MANUAL: Iris must be adjusted manually.
varying light conditions.
CONSTANT: Auto Iris is constantly active.
Reduces the camera's iris
Sliding scale:
level for proper exposure.
– (1 to 15) +
Adjusts the manual focus
Sliding scale:
speed.
– (1 to 8) +
Adjusts the manual iris speed. Sliding scale:
CONSTANT
8
2
5
– (1 to 10) +
Max. Zoom Speed
Adjusts the manual zoom
SLOW, MEDIUM, or FAST
FAST
OFF or ON
ON
speed.
Digital Zoom
Enables digital zoom.
Restore Defaults
Restores all default settings
for this menu.
2.4
PTZ Setup Menu
The PTZ Menu provides access to pan/tilt/zoom settings that can be changed or customized.
Menu items marked with an asterisk (*) are the default settings.
PTZ Setup
*
*
*
*
*
*
*
*
*
Exit...
Autopan:
Tour 1 Period:
Tour 2 Period:
PTZ Fixed Speed:
Inactivity:
Inact. Period
AutoPivot:
AutoDome Orientation
Freeze Frame on Preposition
Tilt Up Limit...
Restore Defaults
30 deg/sec
5 sec
5 sec
4
OFF
2 min
ON
NORMAL
ON
* = Factory Setting
Focus / Iris: Select
PTZ Menu Choices:
Bosch Security Systems, Inc.
User Manual
F.01U.215.781 | 1.0 | 2011.04
14
en | On-Screen Display Menu Navigation
Menu
AutoDome 600 Series Analog PTZ Camera
Description
Sub-menu / Description
Default
Setting
Exit
Exits the menu.
AutoPan
Adjusts speed of camera during
Sliding scale:
AutoPan and AutoScan.
– (1º/sec. to 60º/sec.) +
Changes dwell time between
Sliding scale:
presets during the tour.
– (3 sec. to 10 min.) +
Changes dwell time between
Sliding scale:
presets during the tour.
– (3 sec. to 10 min.) +
Sets pan and tilt speed when
Sliding scale:
controlled by a fixed speed
– (1 to 15) +
Tour 1 Period
Tour 2 Period
PTZ Fixed Speed
30º/sec.
5 sec.
5 sec.
4
controller.
Inactivity
OFF
Selects the mode that an
Scene 1: Returns to Preset 1.
AutoDome reverts to after the
Prev Aux: Returns to previous activity, such
period of inactivity set in the
as Aux commands 1, 2, 7, 8, 50, or 52.
inactivity period.
OFF: Remains on the current scene
indefinitely.
Inactivity Period
AutoPivot
Sets the time period of inactivity
Sliding scale:
2 min.
before the above action occurs.
– (3 sec. to 10 min.) +
Automatically rotates the camera
OFF or ON
ON
INVERTED or NORMAL
NORMAL
OFF or ON
ON
180º when following a subject
traveling directly beneath the
camera.
AutoDome
Automatically rotates the video
Orientation
180º.
Freeze Frame On
Holds a preposition video frame
Preposition
while moving to another
preposition.
Tilt Up Limit...
Sets the upper tilt limit of the
Use joystick to move to a scene.
camera.
Azimuth Zero...
Sets the zero degree pan position.
Use the joystick to move to a scene that you
want to set as the zero degree pan position
and as the North compass heading.
Refer to Section 7.8 Azimuth, Elevation, and
Compass Directions, page 50.
Restore Defaults
Restores the default setting for this
menu only.
F.01U.215.781 | 1.0 | 2011.04
User Manual
Bosch Security Systems, Inc.
AutoDome 600 Series Analog PTZ Camera
2.5
On-Screen Display Menu Navigation | en
15
Display Setup Menu
Provides access to display settings that can be changed or customized. Menu items with an *
are the default settings.
Display Setup
Exit...
* Title OSD:
* Camera OSD:
Display Adjust:
Sector Blanking...
Privacy Masking...
Edit Sector Title
Edit Scene Title
Restore Defaults
MOMENTARY
ON
* = Factory Setting
Focus / Iris: Select
Display Setup Menu Choices:
Menu
Description
Sub-menu / Description
Default
Setting
Exit
Saves and exits the menu.
Title OSD
Controls how the OSD displays
OFF: Titles are hidden.
sector or shot titles.
ON: Titles are displayed continuously.
MOMENTARY
MOMENTARY: Titles are displayed for a
few seconds then disappear from the
screen.
Camera OSD
Controls how the OSD displays
OFF or ON
ON
camera response information,
such as Digital Zoom, Iris open/
close, and Focus near/far.
Display Adjust
Adjusts the text brightness and
Exit: Exits the menu.
vertical position of the on-screen
Up: Moves screen title up.
title.
Down: Moves screen title down.
Brighter: Brightens the intensity of the onscreen text.
Darker: Darkens the intensity of the onscreen text.
Azimuth
Displays azimuth/elevation
On: Displays azimuth/elevation readings.
values.
Off: Hides azimuth/elevation readings.
OFF
Refer to Section 7.8 Azimuth, Elevation, and
Compass Directions, page 50.
Compass
Displays compass heading.
On: Displays compass heading.
OFF
Off: Hides compass heading.
Refer to Section 7.8 Azimuth, Elevation, and
Compass Directions, page 50.
Bosch Security Systems, Inc.
User Manual
F.01U.215.781 | 1.0 | 2011.04
16
en | On-Screen Display Menu Navigation
Menu
AutoDome 600 Series Analog PTZ Camera
Description
Sub-menu / Description
Default
Setting
Sector Blanking
Allows video blanking of selected
Exit: Exits the menu.
sectors. Available sectors are 1
Sector (1-16): Press Focus/Iris to blank or
through 16. Follow the on-screen
clear a sector.
instructions.
Privacy Masking
Allows masking of sensitive
Exit: Saves and exits menu.
areas. Up to 24 privacy masks are
Mask: 1 to 24 masking areas. Follow the
available, with a maximum limit
on-screen instructions to set a mask. See
of eight (8) to a scene.
Section 7.1 Alarm Rules, page 42.
Restore Defaults: Restores the default
settings for this menu only.
Edit Sector Title
Allows editing existing Sector
Select a sector title to access the
(Zone) Titles
character palette. See
Section 3.3 Specifying a Shot or a Sector
Title, page 26, for instructions.
Edit Scene Title
Allows editing existing Scene
Select a scene title, then choose a menu
(Shot) Titles
option:
–
Edit Scene Title to access the
character palette. See
Section 3.3 Specifying a Shot or a
Sector Title, page 26, for instructions.
–
Clear Scene to delete the selected
scene title.
Restore Defaults
Restores the default setting for
this menu only.
2.6
Communication Setup Menu
The Communication Setup Menu provides access to baud rate and Bilinx control settings.
Menu items marked with an asterisk (*) are the default settings.
Communication Setup
Exit...
* AutoBaud:
ON
* Baud Rate
9600
* Bilinx:
ON
Restore Defaults...
* = Factory Setting
Focus / Iris: Select
F.01U.215.781 | 1.0 | 2011.04
User Manual
Bosch Security Systems, Inc.
AutoDome 600 Series Analog PTZ Camera
On-Screen Display Menu Navigation | en
17
Communication Setup Menu Choices:
Menu
Description
Sub-menu / Description
Default
Setting
Exit
Saves and exits the menu.
AutoBaud
Turns AutoBaud detection on.
ON
Toggles ON or OFF.
ON automatically accepts baud rates from 2400 to
57600.
(Note: If stepping from 2400 to 57600 baud, you
must first set the controller to 19200 for AutoBaud
to detect the higher baud rate.)
Baud Rate Manually sets the baud rate when
AutoBaud is set to OFF.
Choices are 2400, 4800, 9600, 19200, 38400, and
9600
57600. Then follow the OSD to confirm the
selection.
Bilinx
Turns on Bilinx control communication. Toggles ON or OFF.
ON
(Only available when not connected to
a Bilinx data interface unit.)
2.7
Alarm I/O Setup
The Alarm Setup Menu provides access to the Alarm I/O Setup Menu to establish the alarm
inputs and outputs and to configure alarm rules.
Alarm I/O Setup
Exit...
Inputs Setup...
Outputs Setup...
Rule Setup...
Restore Defaults...
Focus / Iris: Select
Bosch Security Systems, Inc.
Inputs Setup
Exit...
1. Alarm Input 1
2. Alarm Input 2
3. Alarm Input 3
4. Alarm Input 4
5. Alarm Input 5
6. Alarm Input 6
7. Alarm Input 7
8. NONE
9. NONE
10. NONE
11. NONE
12. NONE
N.C.S.
N.O.S.
N.O.
N.C.
N.O.
N.C.
N.O.
Physical
Input 1-7
Physical
Output 9-12
Focus / Iris: Select Type
Right / Left: Select Mode
User Manual
F.01U.215.781 | 1.0 | 2011.04
18
en | On-Screen Display Menu Navigation
AutoDome 600 Series Analog PTZ Camera
Alarm Setup Menu Choices:
Menu
Description
Sub-menu / Description
Default
Setting
Exit
Saves and exits the menu.
Inputs Setup
Defines physical inputs or events and
commands that can be used in a rule.
There are twelve (12) alarm inputs
available.
Inputs 1-7
Defines the type of physical input.
N.O.: Normally open dry contact.
N.O.
N.C.: Normally closed dry contact.
N.C.S.: Normally closed supervised contact.
N.O.S.: Normally open supervised contact.
Inputs 8-12
NONE
Defines input commands that can be
NONE: No command defined.
used in a rule. Command inputs can also
Aux On: Responds to a standard or custom
be customized by using non-assigned
keyboard ON (1-99) command.
keyboard command numbers.
Aux Off: Responds to a standard or custom
keyboard OFF (1-99) command.
Shot: Responds to a Preset shot or scene from
1-99.
AutoTrack: Triggers an alarm when set to ON.
Motion Detection: Triggers an alarm when set
to ON.
NOTICE!
Alarm inputs 1 and 2 provide tamper detection, if programmed as supervised, for breaks or
shorts in an alarm circuit. See the VG5 AutoDome Installation Manual for wiring instructions.
Outputs Setup Menu
Outputs Setup...
Exit...
1. Alarm Output 1
2. Alarm Output 2
3. Alarm Output 3
4. Alarm Relay
5. NONE
6. Aux On
7. Aux Off
8. Shot
9. OSD
10. Transmit
11. NONE
12. NONE
N.O.
N.O.
N.O.
N.O.
1
8
99
1-4
Physical
Outputs
5-12
Command
Outputs
Focus / Iris: Select Type
Right / Left: Select Mode
F.01U.215.781 | 1.0 | 2011.04
User Manual
Bosch Security Systems, Inc.
AutoDome 600 Series Analog PTZ Camera
On-Screen Display Menu Navigation | en
19
Outputs Setup Menu Choices
Menu
Description
Exit
Saves and exits the
Sub-menu / Description
Default Setting
Defines a physical
N.O.: Normally open circuit
N.O.
output.
N.C.: Normally closed circuit
menu.
Outputs Setup Defines physical outputs
and keyboard commands
for use in a rule.
Outputs 1-3
Alarm Relay
A fixed output available
for use in a rule.
Outputs 5-12
Defines a command
Aux On: A keyboard ON command.
NONE
output for use in a rule.
Aux Off: A keyboard OFF command.
Outputs 5 and 6
Shot: Recalls a preset shot.
set to OSD and
OSD: An on screen display.
Shot 1
Transmit: Transmits a message back to the head
end (available with RS-232 serial connections,
Bilinx, and IP AutoDome models).
AutoTrack: Turns AutoTrack on or off as an output.
NONE: No command defined.
2.8
Rule Setup Menu
The Rule Setup Menu shows the status of the rules and lets you add new rules or modify an
existing rule. The default setting is Empty.
NOTICE!
You can program a total of twelve rules. You must define the inputs and outputs before you
program a rule. See Section 2.7 Alarm I/O Setup, page 17, to configure alarm inputs and
outputs.
Rule Setup...
Exit...
1. Rule 1
2. Rule 2
3. Rule 3
4. Rule 4
5. Rule 5
6. Rule 6
7. Rule 7
8. Rule 8
9. Rule 9
10. Rule 10
11. Rule 11
12. Rule 12
4. Rule 4
Enabled
Disabled
Invalid
Empty
Empty
Empty
Empty
Empty
Empty
Empty
Empty
Empty
Empty
Focus / Iris: Select
Bosch Security Systems, Inc.
Rule 1
Exit...
Enabled
Input:
NONE
NONE
NONE
Output:
OSD
Shot 2
Alarm Relay
NONE
YES
2 sec
Right / Left: Select Period Time
Focus / Iris: Select Type
User Manual
F.01U.215.781 | 1.0 | 2011.04
20
en | On-Screen Display Menu Navigation
AutoDome 600 Series Analog PTZ Camera
Rule Setup Menu Choices
Menu
Description
Sub-menu / Description
Default
Setting
Exit
Saves and exits the menu.
Rule 1-12
Displays the status of a rule
Enabled: The rule inputs and outputs are properly
on the right side of the
defined and the rule is turned on.
menu. There are four (4)
Disabled: The rule inputs and outputs are defined but the
possible rule statuses.
rule is turned off.
Empty
Invalid: The rule has a missing or invalid input or output.
Empty: The rule has no inputs or outputs defined.
Selecting a Rule number provides access to its configuration menu. The Rule # Menu allows
you to configure a rule from previously defined alarm inputs and outputs. Once an alarm is
configured with valid inputs and outputs, it can be turned on or off (enabled or disabled)
through its configuration menu.
Rule # Choices:
Menu
Description
Sub-menu / Description
Default
Setting
Exit
Saves and exits the menu.
Enabled
Turns the rule on or off after its
YES to enable or NO to disable
NO
Toggles through a list of valid
Alarm Inputs 1 – 7 and any additional inputs which
NONE
inputs set in the Alarm I/O Setup
were set in the Inputs Setup Menu, including Aux
> Inputs Setup Menu that define
On/Off (1-99), Shot, and NONE.
inputs and outputs have been
defined.
Input
the rule's inputs. A rule can have
up to four (4) inputs.
Output
Toggles through a list of valid
Alarm Outputs 1 – 3 and any additional outputs set
NONE
outputs set in the Alarm I/O Setup in the Outputs Setup Menu including: Alarm Relay,
> Outputs Setup Menu that
Aux On/Off (1-99), Shot, OSD, Transmit, and
defines a rule's outputs.
NONE.
Some outputs, such as Alarm Outputs 1-3, Alarm
Relay, and Aux On/Off can be set to be active for a
specific duration of time as follows:
Seconds: 1-5, 10, 15, or 30
Minutes: 1-5 or 10
Latched: The alarm stays active until acknowledged.
Follows: The alarm follows the alarm rule.
NOTICE!
You can include up to four (4) Input and Output events in a single rule. Each input and output,
however, must be true for the alarm's rule to be valid and enabled.
F.01U.215.781 | 1.0 | 2011.04
User Manual
Bosch Security Systems, Inc.
AutoDome 600 Series Analog PTZ Camera
2.9
On-Screen Display Menu Navigation | en
21
Language Menu
The Language Menu provides access to a list of languages to display the on-screen menus.
Language
Exit...
English
Spanish
French
German
Portuguese
Polish
Italian
Dutch
Focus / Iris: Save and Exit
Language Menu Choices:
Menu
Description
Exit
Saves and exits the menu.
Choose a language
Select a language in which the system displays the on-screen menus.
2.10
Default Setting
Advanced Feature Setup Menu
The Advanced Menu provides access to the Advanced Features Setup menus such as image
Stabilization, AutoTrack Sensitivity and Virtual Masking. Menu items marked with an asterisk
(*) are the default settings.
Advanced Feature Setup
Exit...
* Stabilization
* AutoTrack Sensitivity
AutoTrack TImeout
AutoTrack TImeout Period
* Camera Height:
Virtual Masking...
Restore Defaults...
OFF
Auto
OFF
5 min
12
Focus / Iris: Save and Exit
Bosch Security Systems, Inc.
User Manual
F.01U.215.781 | 1.0 | 2011.04
22
en | On-Screen Display Menu Navigation
AutoDome 600 Series Analog PTZ Camera
Advanced Feature Setup Menu Choices:
Menu
Description
Sub-menu / Description
Default
Setting
Exit
Saves and exits the menu.
Stabilization
Turns on video stabilization.
AutoTrack Sensitivity Sets the sensitivity level of
OFF
Auto
Sliding scale: -(Auto, 1 to 20)+
AutoTrack.
Where 1 is more sensitive and 20 is less
sensitive. Auto varies the sensitivity level
based on various lighting conditions.
AutoTrack Timeout
Toggles the AutoTrack Timeout
When On, AutoTrack “gives up” after the
feature.
Timeout Period if tracking in a confined
OFF
area (for example a tree, a flag, etc).
AutoTrack Timeout
Enters the AutoTrack Timeout
Period
Period set menu
Camera Height
Virtual Masking
Sliding scale 30 sec, 1 to 30 min.
5 min
Defines the height of the
A range from 2.4 m (8 ft) to 30.7 m
3.6 m (12 ft)
camera for AutoTrack.
(100 ft)
Enters the Virtual Mask menu.
Allows up to 24 virtual masks using five
See Section 7.3 Virtual Masking,
anchor points.
page 48.
Restore Defaults
Restores the default settings
for this menu.
2.11
Diagnostics Menu
The Diagnostics menu provides access to a list of diagnostic tools and events.
Diagnostics
Exit...
Alarm Status...
BIST...
Internal Temp:
High Temp Events:
Highest Temp
Low Temp Events:
Lowest Temp:
Security Access:
CTFID Access:
Homing Events:
Homing Failed:
Loss Home Events
Home Position Good
Restart Events:
Low Volt Events:
Power Up Events:
Video Loss Events:
Total Time On
Deg F / Deg C
Deg F / Deg C
Deg F / Deg C
Deg F / Deg C
Deg F / Deg C
0
0
0
0
0
YES
0
0
0
0hr 0min
Focus / Iris: Save and Exit
Diagnostic Events
F.01U.215.781 | 1.0 | 2011.04
User Manual
Bosch Security Systems, Inc.
AutoDome 600 Series Analog PTZ Camera
On-Screen Display Menu Navigation | en
23
Menu
Description
Exit
Saves and exits the menu.
Alarm Status
Enters the Alarm Status menu and displays the
Alarm Inputs 1 to 7, Alarm Outputs 1
real time status of alarm inputs and outputs.
to 3 and Alarm Relay
BIST
Sub-menu / Description
Enters the Perform Built-in Self Tests menu. If
YES to start test. NO to exit the
confirmed, the BIST tests start and the results
menu.
are displayed.
Typical results displayed as follows:
BIST
Exit...
Data Flash:
PASS
Bilinx:
PASS
FPGA:
PASS
Digital I/O 1: PASS
Digital I/O2:
Internal Temp.
Displays the current dome temperature.
High Temp Events
Displays the number of times the high
PASS
VCA:
PASS
Homing:
PASS
temperature threshold is exceeded.
Highest Temp
Displays the highest temperature reached.
Low Temp Events
Displays the number of times the low
temperature threshold is exceeded.
Lowest Temp
Displays the lowest temperature reached.
Security Access
Displays the number of times the lockedcommand menu is unlocked.
CTFID Access
Displays the number of times the Configuration
Tool is accessed.
Homing Events
Displays the number of times the AutoDome was
rebooted.
Homing Failed
Displays the number of times the AutoDome
failed to home properly.
Loss Home Events:
Displays the number of times the AutoDome lost
the home position.
Home Position Good
Displays if the current AutoDome home position
is good. Displays YES if good.
Restart Events
Displays the number of restart events.
Low Volt Events
Displays the number of times the AutoDome
dropped below the acceptable voltage limit.
Power Up Events
Displays the number of power up events.
Video Loss Events
Displays the number of time that video was lost.
Bosch Security Systems, Inc.
User Manual
F.01U.215.781 | 1.0 | 2011.04
24
en | On-Screen Display Menu Navigation
2.11.1
AutoDome 600 Series Analog PTZ Camera
Alarm Status Submenu
This menu displays the status of the alarm inputs and alarm outputs.
Alarm Status
Exit...
Alarm Input 1
Alarm Input 2
Alarm Input 3
Alarm Input 4
Alarm Input 5
Alarm Input 6
Alarm Input 7
Alarm Output 1
High
High
Open
Open
Open
Open
Open
Open
Focus / Iris: Save and Exit
Menu
Description
Options
Exit
Saves and exits the menu.
Alarm Input 1...7
Displays the status of alarm inputs 1 through 7.
High
Low
Open (Normally Open)
Closed (Normally Closed)
Alarm Output
Displays the status of the alarm output.
F.01U.215.781 | 1.0 | 2011.04
User Manual
Bosch Security Systems, Inc.
AutoDome 600 Series Analog PTZ Camera
3
Common AutoDome User Commands (unlocked) | en
25
Common AutoDome User Commands (unlocked)
This chapter details the commonly used Bosch keyboard setup commands. See
Section 6 Keyboard Commands by Number, Page 41, for a complete list of commands.
3.1
Setting AutoPan Mode
AutoPan mode pans the AutoDome camera 360º or pans between user defined limits (when
programmed). The AutoDome camera continues to pan until stopped by moving the joystick.
To pan 360º:
1.
Press ON-1-ENTER.
2.
Move the joystick to stop the pan.
To set left and right pan limits:
1.
Move the camera to the starting position and press SET-101-ENTER to set the left limit.
2.
Move the camera to the end position and press SET-102-ENTER to set the right limit.
To start AutoPan between limits:
3.2
1.
Press ON-2-ENTER.
2.
Move the joystick to stop the pan.
Setting Preset Shots
Preset shots are saved camera positions. Shots are saved as scenes, therefore, the terms
SHOT and SCENE are used interchangeably.
To set a Shot:
1.
2.
Move the camera to the position you want to save.
Press SET-#-ENTER where # can be a number from 1 to 99 that identifies the camera
position of the scene.
3.
To specify a title for the shot, see the procedure below.
To view a Shot:

Press SHOT-#-ENTER where # is the number of the scene position you want to view.
To store or clear a Shot:
1.
Press SET-100-ENTER to access the Store/Clear Scene Menu.
2.
Follow the on-screen instructions.
To disable overwrite confirmations:
If you overwrite a preset shot the AutoDome issues a confirmation message prompting you
approve the overwrite. To disable this confirmation message issue the OFF-89-ENTER
command.
Bosch Security Systems, Inc.
User Manual
F.01U.215.781 | 1.0 | 2011.04
26
3.3
en | Common AutoDome User Commands (unlocked)
AutoDome 600 Series Analog PTZ Camera
Specifying a Shot or a Sector Title
The AutoDome provides an alphanumeric character palette used to specify a title for a shot
(scene) or for a sector (zone).
1.
To specify a title, navigate to the shot or scene:
–
for a shot: set a new shot or view a stored shot then press ON-62-ENTER.
–
for a scene: move the AutoDome to the scene (zone) then press ON-63-ENTER.
2.
Use the joystick to move the cursor to highlight a character.
3.
Press Focus/Iris to select the character.
4.
Continue to select characters (up to 20) until you have created the title.
5.
To clear a character from the title:
a.
Use the joystick to highlight the Clear OR Position Character prompt.
b.
Move the joystick left or right until the cursor is below the title character you need to
clear.
6.
3.4
c.
Press Focus/Iris to clear the character.
d.
Move the joystick up to bring the cursor back into the character palette.
To save the title:
a.
Use the joystick to highlight the Exit prompt.
b.
Press Focus/Iris to save the title.
Configuring Preposition Tours
A Preposition Tour automatically moves the camera through a series of preset or saved shots.
The VG5 Autodome has one (1) standard preset tour and one (1) customized preset tour. Tour
1 is a standard tour that moves the camera through a series of shots in the sequence they
were set. Tour 2 is a custom tour that allows you to change the sequence of shots in the tour
by inserting and deleting scenes.
To start Preposition Tour 1:
1.
2.
Set a series of preset shots in the order that you want the AutoDome to cycle through.
Press ON-8-ENTER to start the tour. The tour then cycles through the series of shots until
it is stopped.
To stop a Preposition Tour:

Press OFF-8-ENTER or move the joystick to stop either type of tour.
To add or remove scenes to Preposition Tour 1:
1.
Press SHOT-900-ENTER to access the Add/Remove Scenes Menu.
2.
Use the Focus/Iris buttons to add or remove the selected scene from the tour.
To start custom Preposition Tour 2:

Press ON-7-ENTER to start a tour. The tour cycles through the series of shots in the order
they were defined until it is stopped.
To edit a custom Preposition Tour 2:
1.
Press SET-900-ENTER to access the Add/Remove Menu.
2.
Press the Focus/Iris buttons to add or remove the selected scene.
To change the dwell period of a tour:
1.
Press ON-15-ENTER to access the Tour Period Menu.
2.
Select the tour (Tour 1 or Tour 2) and follow the on-screen instructions.
F.01U.215.781 | 1.0 | 2011.04
User Manual
Bosch Security Systems, Inc.
AutoDome 600 Series Analog PTZ Camera
3.5
Common AutoDome User Commands (unlocked) | en
27
Programming the Inactivity Operation
You can program the AutoDome to automatically change its operating mode after a period of
inactivity.
To access the Inactivity mode (locked command):
1.
Press OFF-90-ENTER to turn off the command lock.
2.
Press ON-9-ENTER to access the Inactivity Mode Menu.
3.
Select one of the following choices:
–
Return to Scene 1: Returns the camera position back to the first scene saved in
memory.
–
Recall Previous Aux: Returns the camera to the previous operating mode, such as a
Preposition Tour.
3.6
Recording Tours
The VG5 AutoDome can make up to two (2) recorded tours. A Recorded Tour saves all manual
camera movements made during the recording, including its rate of pan, tilt and zoom speeds
and other lens setting changes.
To Record Tour A:
1.
Press ON-100-ENTER to start recording a tour.
2.
Press OFF-100-ENTER to stop recording.
To playback Recorded Tour A:
1.
Press ON-50-ENTER to begin continuous playback.
2.
Press OFF-50-ENTER or move the joystick to stop playback
To Record Tour B:
1.
Press ON-101-ENTER to start recording the tour.
2.
Press OFF-101-ENTER to stop the tour.
To playback Recorded Tour B:
1.
Press ON-52-ENTER to begin continuous playback.
2.
Press OFF-52-ENTER or move the joystick to stop playback.
Bosch Security Systems, Inc.
User Manual
F.01U.215.781 | 1.0 | 2011.04
28
en | Alternative Control Protocols
4
AutoDome 600 Series Analog PTZ Camera
Alternative Control Protocols
The VG5 AutoDome supports three alternative control protocols that allows a user to send
commands and to receive information from the AutoDome. The VG5 AutoDome supports the
following protocols:
–
Pelco-P
–
Pelco-D
–
American Dynamics (AD) Manchester
–
American Dynamics (AD) Sensormatic RS-422
The VG5 AutoDome natively supports the two Pelco protocols. To use the AD Manchester or
the AD Sensormatic RS-422 protocol you must purchase a separate module. The module
contains instructions to install any additional hardware and information about additional onscreen menus.
4.1
Setting FastAddress with Alternative Protocols
The VG5 AutoDome offers remote addressing via the FastAddress capability from a keyboard
that uses an alternative protocol. The FastAddress feature allows you to instal all domes first,
then set the addresses via the control system. Since it is not necessary to go to the camera’s
physical location, this feature makes it easier to readdress cameras at a later time.
4.1.1
Using an American Dynamics Controller
Prior to setting the FastAddress for each camera, all cameras will initially move together. After
the Unique Identifier is set, only the camera that was set with the FastAddress is capable of
sending and receiving commands. When setting the FastAddress, it is important to remember
that some American Dynamics Manchester systems use address blocks of 1 to 64, while
American Dynamics Sensormatic systems typically use address blocks of 1 to 99; meaning
that when the controller/keyboard displays video for cameras higher than 64 or 99 the
keyboard/controller sends a different control code to the camera (see Section A Appendix:
FastAddress Conversions, page 61, for conversion charts). For example at Camera 65, the
American Dynamics Manchester system sends out an address of 1, while the Sensormatic RS422 system with an address of 100 also sends out an address of 1.
It is NOT NECESSARY to convert these numbers with the Bosch FastAddress method. The
camera automatically detects the address being transmitted by the Sensormatic RS-422
control system and adjusts the camera accordingly.
F.01U.215.781 | 1.0 | 2011.04
User Manual
Bosch Security Systems, Inc.
AutoDome 600 Series Analog PTZ Camera
Alternative Control Protocols | en
29
Setting the FastAddress with an AD Manchester or AD Sensormatic RS-422 Keyboard
1.
Enter the AutoDome Setup menu using 66-Preset/Shot on most AD/Sensormatic RS-422
keyboards. Note: Based on your keyboard model, it may be necessary to enter the
PROGRAMMING mode prior to entering this command.
2.
Move the joystick to highlight the Command Lock menu. Note: The first time the VG4 is
set-up out of the box, the Command Lock feature is set to OFF for the first two (2)
minutes of operation and then reverts to the ON setting.
Setup Menu
Exit...
Command Lock:
Bosch Menu
Camera Setup
PTZ Setup
Edit Password
*FastAddress:
Software Version
Ack and Reset Alarms
Restore All Settings
OFF
Not Set
* = Factory Setting
Focus / Iris: Select
3.
Press the FOCUS or the IRIS button to turn Command Lock to OFF. Move to the
FastAddress menu and press the FOCUS or the IRIS button to open the menu. Use the
joystick to re-enter the 6-digit factory-set Unique Identifier displayed for the VG4
AutoDome. See example as follows:
Enter FastAddress
FastAddress:
Not Set
Unique Identifier:
000000
r
Continue...
Exit...
200668
Joystick: Match Identifier
–
Move the joystick up or down to select the individual number. Move the joystick right to
move to the next FastAddress number position.
When completed, the FastAddress number entered must match the Unique Identifier
displayed. See example as follows:
Enter FastAddress
FastAddress:
Not Set
Unique Identifier:
200668
r
Continue...
Exit...
200668
Joystick: Match Identifier
Bosch Security Systems, Inc.
User Manual
F.01U.215.781 | 1.0 | 2011.04
30
en | Alternative Control Protocols
AutoDome 600 Series Analog PTZ Camera
NOTICE!
If the user does not enter the exact manufacturer Unique Identifer as displayed on-screen, the
FastAddress can not be set and the only option available is to Exit the menu.
4.
Move the joystick right to highlight Continue. Then, press the FOCUS or the IRIS button.
Enter FastAddress
FastAddress:
Not Set
Unique Identifier:
200668
r
Continue...
Exit...
200668
Joystick: Match Identifier
5.
The AutoDome automatically reads the correct Address sent by the controller and is
displayed as Save ## as FastAddress (## is based on either 1-64 AD/Manchester or 1-99
AD/Sensormatic RS-422). It is NOT POSSIBLE to change the address that is displayed.
The following options are available:
–
–
Press the FOCUS or the IRIS button to store the FastAddress number.
Move the joystick to highlight Clear Current FastAddress and then press the FOCUS
or the IRIS button to clear any currently saved Fast Address.
–
Move the joystick to highlight Exit Without Change to exit the FastAddress menu
without saving any changes.
FastAddress
FastAddress:
Not Set
Save “##” as FastAddress
Clear Current FastAddress
Exit Without Change
Focus/Iris: Select
F.01U.215.781 | 1.0 | 2011.04
User Manual
Bosch Security Systems, Inc.
AutoDome 600 Series Analog PTZ Camera
6.
Alternative Control Protocols | en
31
The on-screen display menu confirms that the VG4 AutoDome stored the FastAddress
and then returns to the Main menu with the new Fast Address displayed. Move the
joystick to highlight EXIT, and then press FOCUS or IRIS to exit the menus.
New Fast Address Saved
Setup Menu
Exit...
Command Lock:
Bosch Menu
Camera Setup
PTZ Setup
Edit Password
*FastAddress:
Software Version
Ack and Reset Alarms
Restore All Settings
OFF
3
* = Factory Setting
Focus / Iris: Select
4.1.2
Using a Pelco Controller
This section provides instructions to set a FastAddress with a Pelco keyboard or controller.
–
An AutoDome with an address set to 0 responds to commands set to any address.
–
Pelco-P protocol must use addresses 1 to 32.
–
Pelco-D protocol must use addresses 1 to 254.
NOTICE!
A previously configured AutoDome with an address above 32 (Pelco-P upper limit) or 254
(Pelco-D upper limit) can be used without readdressing the unit. However, no two (2)
addresses can be the same. For example:
Pelco-P addresses above 32 are repeated in multiples of 32 (1, 33, 65, 97 are the same).
Pelco-D addresses above 254 are repeated in multiples of 254 (1, 255, 509, 763 are the
same).
Setting FastAddress with a Pelco Keyboard
1.
Press and hold 95-PRESET for two seconds to open the Pelco Setup menu.
2.
Move the joystick to select the Command Lock menu.
3.
Press the FOCUS or the IRIS button to turn Command Lock to OFF.
4.
Move to the FastAddress menu and press the FOCUS or the IRIS button to open the
menu.
5.
Use the joystick to enter the unique identifier for the VG4 AutoDome.
–
Move the joystick up or down to select the number.
–
Move the joystick right to move to the next number position.
6.
Move the joystick right to select Continue. Then, press the FOCUS or the IRIS button.
7.
Use the keyboard to enter the FastAddress number. Then, press the Camera button.
Note: You must first clear an assigned FastAddress number to use the number for a
different VG4 AutoDome.
Bosch Security Systems, Inc.
User Manual
F.01U.215.781 | 1.0 | 2011.04
32
en | Alternative Control Protocols
AutoDome 600 Series Analog PTZ Camera
8.
Move the joystick down then back up to set the FastAddress number.
9.
Press the FOCUS or the IRIS button to store the FastAddress number.
The on-screen display menu confirms that the VG4 AutoDome stored the FastAddress
number.
4.2
Pelco Protocol Mode
The Pelco Mode features Auto Baud Detection that automatically detects and adjusts the
AutoDome protocol and baud rate to match that of the controller. The AutoDome responds to
Pelco-D or Pelco-P protocol commands.
NOTICE!
The AutoDome supports only the RS-485 protocol while in Pelco mode. It does not transmit
responses back to the controller.
4.2.1
Hardware Configuration
The AutoDome is configured from the factory for RS-485 operation in Pelco Protocol Mode.
1.
Connect the controller's TX terminals to the AutoDome's TxD terminals. See the
AutoDome Modular Camera System Installation Manual for complete wiring instructions.
2.
Pan or tilt the keyboard joystick to confirm that control has been established to the
AutoDome (approximately five (5) seconds).
NOTICE!
If control is not established, ensure that the RS-232/RS-485 selector switch is positioned to
RS-485 (outward toward the LED lights). This switch is located on the bottom of the
AutoDome CPU board, under the camera head and next to the LED lights. See Figure 4.1.
Figure 4.1
1
2
3
4
F.01U.215.781 | 1.0 | 2011.04
RS-232/RS-485 Selection Switch
CPU Module
Switch Location
LEDs
RS485
User Manual
Bosch Security Systems, Inc.
AutoDome 600 Series Analog PTZ Camera
4.2.2
Alternative Control Protocols | en
33
Pelco Keyboard Commands
Pelco control commands are composed of a sequence of two (2) keyboard inputs with the
following convention: 1) a Command Number and 2) a Function key input.
The AutoDome uses the PRESET command key to save and recall presets (pre-positions) 1
through 99.
NOTICE!
To save a preset, enter the desired number and hold the PRESET key for approximately two
(2) seconds. To recall a preset, enter the desired preset number (or command) and
momentarily press and release the PRESET key.
4.2.3
Pelco Keyboard Commands
Keyboard Command User Action
Description
0-Pattern
Initiates recording continuous playback based upon
Press
current Recording setting (A or B) in the Setup
Menu.
Press and hold
Initiates recording based upon current Recording
setting (A or B) in the Setup Menu. Press ACK to end
recording.
1-Pattern
Press
Initiate Recording A continuous playback.
Press and hold
Initiate Recording A. Press ACK to end recording.
2-Pattern
Press
Initiate Recording B continuous playback.
Press and hold
Initiate Recording B. Press ACK to end recording.
3-Pattern
Press
Initiate the AutoDome standard preset tour (Tour 1).
4-Pattern
Press
Initiate the AutoDome custom preset tour (Tour 2).
1 – Aux On / Aux Off Press
Activates / deactivates alarm output 1.
2 – Aux On / Aux Off Press
Activates / deactivates alarm output 2.
3 – Aux On / Aux Off Press
Activates / deactivates alarm output 3.
4 – Aux On / Aux Off Press
Activates / deactivates alarm relay.
91 – Aux On
Press
Activate Zone Scan (display zone titles).
92 – Aux On
Press
Deactivate Zone Scan (re-move zone titles)
Bosch Security Systems, Inc.
User Manual
F.01U.215.781 | 1.0 | 2011.04
34
en | Alternative Control Protocols
4.2.4
AutoDome 600 Series Analog PTZ Camera
Special Preset Commands
Some Pelco mode preset commands have a special meaning and override the normal Pelco
preset function as follows:
Preset Command
Description
33-PRESET
Pans the AutoDome 180° (Flip).
34-PRESET
Goes to Zero Pan (original home position).
80-PRESET
Toggles the Synchronization Mode between Line Lock and Internal
(Pelco Frame Scan). This command is available if commands are
unlocked using the Main menu.
81-PRESET
Initiates Preset Tour 1.
82-PRESET
Initiates Preset Tour 2.
92-PRESET
Sets the Left pan limit for an AutoScan with Limit Stops enabled.
93-PRESET
Sets the Right pan limit for an AutoScan with Limit Stops enabled.
94-PRESET
Initiates a Preset Tour.
95-PRESET
Enables or disables Limit Stops in the Setup Menu for AutoScan.
Invokes the Pelco main Setup Menu when pressed for 2 seconds.
96-PRESET
Stops a scan.
97-PRESET
Initiates FastAddress (Pelco Random Scan).
98-PRESET
Toggles the Synch. Mode between Line Lock and Internal (Pelco Frame
Scan). This command is available only for two (2) minutes after the
power is applied and then reverts to normal preset functionality.
99-PRESET
Starts an AutoScan
NOTICE!
Some Pelco controllers do not support all the preset command numbers. Consult the specific
Pelco controller's documentation for supported preset commands.
F.01U.215.781 | 1.0 | 2011.04
User Manual
Bosch Security Systems, Inc.
AutoDome 600 Series Analog PTZ Camera
5
Pelco On-Screen Menus | en
35
Pelco On-Screen Menus
You can program the AutoDome through the Pelco on-screen display (OSD) menus. To access
the Pelco menus, you must configure the AutoDome for Pelco Mode and invoke the Pelco
main Setup Menu.
5.1
Setup Menu
The Pelco main Setup Menu provides access to the programmable AutoDome settings. Some
menu items are locked and require a system password to use. Menu items marked with an *
are the default settings.
To open the Pelco main Setup Menu (locked commands):
1.
Press 95-PRESET (press the PRESET button for approximately 2 seconds to open).
2.
Use the joystick to highlight a menu item.
3.
Press either the Focus or the Iris key to open a menu item.
4.
Follow the on-screen instructions at the bottom of the screen.
Setup Menu
Exit...
Command Lock:
Bosch Menu
Camera Setup
PTZ Setup
Edit Password
*FastAddress:
Advanced
Software Version
Ack and Reset Alarms
Restore All Settings
Reset All Memory
* = Factory Setting
Focus / Iris: Select
OFF
Not Set
NOTICE!
Use Zoom to select the Exit item from anywhere in a menu.
Menu
Description
Exit
Exits the menu.
Command Lock
Allows or prohibits accessing locked commands. (If password is
(locked)
set, you are prompted to enter the password.
Bosch Menu (locked)
Accesses the full AutoDome configuration menu and all AutoDome
settings.
Camera Setup
Accesses the White Balance and Night Mode camera settings.
PTZ Setup
Accesses the tours, tour periods, scan speed, edit presets, limit
stops, recording, and AutoPivot settings.
Edit Password
Changes the password.
(locked)
FastAddress (locked)
Bosch Security Systems, Inc.
Sets or changes a camera address.
User Manual
F.01U.215.781 | 1.0 | 2011.04
36
en | Pelco On-Screen Menus
AutoDome 600 Series Analog PTZ Camera
Menu
Description
Exit
Exits the menu.
Software Version
Displays the current software versions.
Ack and Reset Alarms Acknowledges and resets active alarms.
Restore All Settings
Restores all settings to their original default setting.
(locked)
Reset All Memory
Clears all settings, including scene shots, tours, and recordings
(locked)
stored in the AutoDome memory.
NOTICE!
After a period of 4.5 minutes of inactivity, the OSD menu times-out and exits without warning.
Some unsaved settings can be lost!
5.1.1
Command Lock (locked)
The Pelco Command Lock Menu allows or prohibits the use of locked commands. The default
setting is ON.
NOTICE!
If the Command Lock is set to ON and you press Focus or Iris on a locked command, the
AutoDome displays the on-screen message: “Command is Locked.”
5.1.2
Bosch Menu (locked)
The Bosch Menu allows full access to the AutoDome main Setup Menu and all AutoDome
configuration settings.
Pelco menu
Bosch menu
Setup Menu
Setup Menu
Exit...
Command Lock:
OFF
Bosch Menu
Camera Setup
PTZ Setup
Edit Password
*FastAddress:
Not Set
Advanced
Software Version
Ack and Reset Alarms
Restore All Settings
Reset All Memory
* = Factory Setting
Focus / Iris: Select
Exit...
Camera Setup
Lens Setup
PTZ Setup
Display Setup
Communication Setup
Alarm Setup
Language
Advanced
Diagnostics
Focus / Iris: Select
Refer to Section 2: On-Screen Display Menu Navigation for a complete description of Bosch
menus and configuration settings.
F.01U.215.781 | 1.0 | 2011.04
User Manual
Bosch Security Systems, Inc.
AutoDome 600 Series Analog PTZ Camera
Pelco On-Screen Menus | en
37
Camera Setup (unlocked)
The Pelco Camera Setup Menu provides access to camera settings.
Camera Setup
Exit...
* White Bal:
* Night Mode:
OUTDOOR
AUTO
* = Factory Setting
Focus / Iris: Select
Camera Setup Menu Choices:
Menu
Description
Sub-menu / Description
Default
Setting
Exit
Exits the menu.?
White
Sets a default value in
OUTDOOR: Sets a default setting if
Balance
case the Pelco
the controller disables white
controller disables the
balance.
white balance.
INDOOR: Sets a default setting if the
OUTDOOR
controller disables white balance.
Night Mode Switches from color to
monochrome.
ON: Sets Night Mode on.
ON (Day/Night
OFF: Sets Night Mode off.
models only)
AUTO: Sets Night Mode to Auto set.
5.1.3
PTZ Setup (unlocked)
The Pelco PTZ Setup Menu provides access to the PTZ settings such as tours, scan speed,
presets, limit stops, recording, and AutoPivot.
PTZ Setup
Exit...
Edit Tour 1...
Edit Tour 2...
Tour 1 Period:
Tour 2 Period:
Scan Speed
Edit Presets...
* Limit Stops:
* Recording:
* Autopivot:
*
*
*
*
*
5 sec
5 sec
30 deg/sec
OFF
“A”
ON
* = Factory Setting
Focus / Iris: Select
Bosch Security Systems, Inc.
User Manual
F.01U.215.781 | 1.0 | 2011.04
38
en | Pelco On-Screen Menus
AutoDome 600 Series Analog PTZ Camera
PTZ Setup Menu Choices:
Menu
Description
Sub-menu / Description
Default
Setting
Exit
Exits the menu.?
Edit Tour 1
Accesses the Add /
Exit: Exits the menu.
Remove Scenes On
Scene (1 - 5): Adds or removes
Standard Tour 1 Menu.
scenes from the Standard Tour.
Accesses the Edit Custom
Exit: Exits the menu.
Tour Menu.
Scene (1 - 5): Adds or removes
Edit Tour 2
scenes from the Custom Tour.
Tour 1 Period
Changes the length of
Sliding scale: – (3 sec. to 10 min.) + 5 sec.
waiting time between
presets.
Tour 2 Period
Changes the length of
Sliding scale: – (3 sec. to 10 min.) + 5 sec.
waiting time between
presets.
Scan Speed
Changes the Autopan and
Sliding scale: – (1°/sec to 60°/sec)
30°/
AutoScan speeds.
+
sec.
Edit Presets
Modifies preset scenes.
1-99 scenes
Limit Stops
Toggles the Limit Stops for
ON or OFF
OFF
“A” or “B”
“A”
ON or OFF
ON
AutoScan.
Recordings
Selects record Pattern 1 or
2, if normal pattern
command does not
respond.
AutoPivot
Follows a subject while
beneath the camera,
without inverting the
picture.
5.1.4
Other Menus
Menu
Description
Default
Edit Password
Sets or displays the password. See Section 1.4 Setting
Setting
Passwords, page 8.
FastAddress (locked)
Sets or changes the AutoDome address.
Software Version
Displays the camera software version.
Not Set
(unlocked)
Ack and Reset Alarms
Acknowledges and resets alarms. If there is no active
alarm input, the OSD displays the following message:
“No Active Alarms.”
Restore All Settings
Restores all settings to their original factory default
(locked)
settings.
Reset All Memory
Restores all settings to their original factory default
(locked)
settings and clears all user programmed settings such
as preset scenes and recordings.
F.01U.215.781 | 1.0 | 2011.04
User Manual
Bosch Security Systems, Inc.
AutoDome 600 Series Analog PTZ Camera
6
Locked
Keyboard Commands by Number | en
Keyboard Commands by Number
Command
Description
1
Scan 360°
Autopan without limits
On/Off
2
Autopan
Autopan between limits
*
On/Off
3
Iris Control
Enters menu (auto, manual)
*
On/Off
4
Focus Control
Enters menu (spot, auto, manual)
On/Off
7
Play Custom Pre-position Tour
Activate/Deactivate
On/Off
8
Play Pre-position Tour
Activate/Deactivate
On/Off
9
Inactivity Mode
Enters menu (Off, Return to Scene 1, Recall
*
39
Function
Comm
Key
No.
On/Off
Previous PTZ Command)
*
On/Off
11
Auto Iris Level Adjust
Enters Iris Level Adjustment menu
On/Off
14
Set Autopan and Scan Speed
Enters speed adjustment slide bar
On/Off
15
Set Pre-position Tour Period
Enters dwell adjustment slide bar
(dwell)
*
On/Off
18
AutoPivot Enable
Enables/disables AutoPivot
On/Off
20
Backlight Comp
Backlight Compensation
On/Off
23
Electronic Shutter
Enters Shutter Speed slide bar
On/Off
24
Stabilization
Electronic Stabilization
On/Off
26
Wide Dynamic Range
Activate/Deactivate
*
On/Off
35
White Balance Mode
Enters White Balance menu
*
On
40
Restore Camera Settings
Restores all setting to their original defaults
*
On/Off
41
Line Lock Phase Adjust
Enters delay adjustment slide bar
*
On/Off
42
Sync Mode
On–Line Lock
*
Off–Internal
*
On/Off
43
Auto Gain Control
AGC–On, Auto, Off
*
On/Off
44
Sharpness
Enters Sharpness menu
*
On
46
Advanced Menu
Enters Main Setup menu
On
47
View Factory Settings
View all menu default settings
On/Off
50
Playback A, continuous
Activate/Deactivate
On/Off
51
Playback A, single
Activate/Deactivate
On/Off
52
Playback B, continuous
Activate/Deactivate
On/Off
53
Playback B, single
Activate/Deactivate
On/Off
56
Night Mode Menu
On, Off, Auto (Day/Night only)
On/Off
57
Night Mode Setting
Enables/disables Night Mode
(Day/Night only)
*
On/Off
58
Day/Night Threshold
On/Off
59
Night Mode Priority
On–menu (Day/Night only)
Motion–Activates Night Mode before slow
shutter, preserving full-frame integration as light
is reduced.
Color–Activates slow shutter before Night Mode,
preserving color longer as light is reduced.
*
On/Off
60
On Screen Display
On–Enable
Off–Disable
Bosch Security Systems, Inc.
User Manual
F.01U.215.781 | 1.0 | 2011.04
40
en | Keyboard Commands by Number
Locked
*
Function
Comm
Key
No.
On
On
AutoDome 600 Series Analog PTZ Camera
Command
Description
61
Display Adjust
Adjust On-screen Display
62
Pre-position Title menu
Enters Pre-position Title menu. Refer to
Section 3.3 Specifying a Shot or a Sector Title,
page 26.
*
On
63
Zone Title Menu
Enters Zone Title menu. Refer to
Section 3.3 Specifying a Shot or a Sector Title,
page 26.
On
64
Alarm Status
Enters Alarm Status menu
Off
65
Alarm Acknowledge
Acknowledge alarm or deactivate physical
outputs
*
On
66
Display Software Version
Displays software version number
On/Off
69
Alarm Rule Activation/Deactivation
On–Enables all alarm rules
Off–Disables all alarm rules
On
72
Re-initialize Camera
Performs camera/lens re-initialization functions
On/Off
78
AutoTrack
Turns AutoTrack on or off
*
On
79
Camera Height
Enters the Camera Height menu
*
On/Off
80
Digital Zoom Lock
Turns digital zoom on and off
On/Off
81
Alarm Output 1
On–Activates output
Open Collector
Off–Deactivates output
Alarm Output 2
On–Activates output
Open Collector
Off–Deactivates output
Alarm Output 3
On–Activates output
Open Collector
Off–Deactivates output
Alarm Output 4
On–Activates output
Relay
Off–Deactivates output
On/Off
On/Off
On/Off
82
83
84
*
On/Off
86
Sector Blanking
Enters Sector Blanking menu
*
On/Off
87
Privacy Masking
Enters Privacy Masking menu
On/Off
89
Preposition Confirmation
On–Isues a message that prompts for approval
to overwrite a preposition
Off–No confirmation message issued
On/Off
90
Command Lock/Unlock
On–Lock on
Off–Lock off
*
On/Off
91
Lens Polarity Menu
On–Reverse
Off–Normal
*
On/Off
92
Lens Polarity Menu
On–Reverse
Off–Normal
*
On/Off
93
Lens Polarity Menu
On–Reverse
Off–Normal
*
On/Off
94
Set Azimuth Zero Point
Sets the zero degree pan position.
Refer to Section 7.8 Azimuth, Elevation, and
Compass Directions, page 50.
F.01U.215.781 | 1.0 | 2011.04
User Manual
Bosch Security Systems, Inc.
AutoDome 600 Series Analog PTZ Camera
Locked
Function
Comm
Key
No.
On/Off
95
Keyboard Commands by Number | en
Command
Description
Display Azimuth/Elevation
On–Displays azimuth/elevation readings
Readings
Off–Hides azimuth/elevation readings
41
Refer to Section 7.8 Azimuth, Elevation, and
Compass Directions, page 50.
On/Off
96
Display Compass Readings
On–Displays compass heading
Off–Hides compass heading
Refer to Section 7.8 Azimuth, Elevation, and
Compass Directions, page 50.
On
99
Factory P/T Home Position
Recalibrates home position; can be used as an
Alarm Output
On/Off
100
Record A
Activate/Deactivate
On/Off
101
Record B
Activate/Deactivate
On
997
FastAddress, display
Display current address
On
998
FastAddress, all units
Display and program current address
On
999
FastAddress, unaddressed domes
Display and program unaddressed AutoDomes
Set
“1-99”
Pre-position Programming
Set ##–Programs a preset view
Shot
“1-99”
Pre-position Recall
Shot ##–Recall programmed preset
Set
100
Pre-position Menu
Enters the Pre-position menu
Set/Shot 101
Autopan Left Limit
Set–Programs left limit
Shot–Shows limit
Set/Shot 102
Autopan Right Limit
Set–Programs right limit
Shot–Shows limit
Set
110
Factory P/T Home Position
Set–Recalibrate home position
*
Set
802
Edit Password
Enters the Edit Password menu
*
Set
899
Reset ALL
Restores all settings to original defaults and
clears all user-programmed settings
Set
900
Edit Tour 1 (Standard)
Enters the Standard Tour Scene menu
Shot
900
Edit Tour 2 (Custom)
Enters the Custom Tour Scene menu
Set/Shot 901-999 Adds/Removes a Preposition Shot
from Tour 1
Bosch Security Systems, Inc.
Set ###–Adds preset
Shot ###–Removes preset
User Manual
F.01U.215.781 | 1.0 | 2011.04
42
en | Advanced Features
7
AutoDome 600 Series Analog PTZ Camera
Advanced Features
This chapter details the advanced features of the VG5 AutoDome Camera.
7.1
Alarm Rules
The AutoDome features a powerful alarm rule engine. In its simplest form, an alarm rule
defines those inputs that activate specific outputs. In its more complex form, a rule can be
programmed to take any combination of inputs and keyboard commands to perform a dome
function. There are numerous combinations of alarm inputs and outputs that can be
programmed into twelve alarm rules.
7.1.1
Controlling Alarm Rules
The AUX 69 command allows a user to enable or disable all alarm rules. By default, alarm rules
are enabled until the OFF-69-ENTER command is issued from a keyboard (there is no
corresponding menu item for this command). Disabling alarms rules does not erase the rule,
the AutoDome preserves the user-defined settings and the rule data is restored when the ON69-ENTER command is issued.
The OFF-69-ENTER command performs the following actions:
–
Disables all alarm rules
–
Displays the message “Ack and Reset Alarms” if an alarm-rule triggered alarm is active
when the AutoDome receives the disable command. You must acknowledge the alarm
before the rule is disabled.
–
7.1.2
Prevents the modification of an alarm rule while disabled.
Alarm Rule Examples
Following are three examples for setting up alarm rules. The first example is a basic alarm
rule, and the second and third examples are more complex.
Example 1: Basic Alarm Rule
Scenario: We want a door alarm contact to:
1.
Flash an OSD message (***ALARM 1***) on the display when the alarm is triggered.
2.
Move the AutoDome camera to a saved position. (For this example Shot 7.)
3.
Transmit a Bilinx signal over the coax cable to the headend system, such as an Allegiant,
to trigger an alarm response.
The sequence to program the above alarm rule example is as follows:
1.
2.
Wire the door contact to Input 1 in the AutoDome. This circuit is normally open.
Define the Alarm Input(s)
–
From the Inputs Setup menu, ensure that Alarm Input 1 is set to N.O. (This is the
default setting for Input 1.)
NOTICE! For instruction on wiring alarm and relay connections, see the VG5 AutoDome
Installation Manual.
3.
F.01U.215.781 | 1.0 | 2011.04
Define the Alarm Outputs from the Outputs Setup menu:
a.
Ensure Output 5 is set to OSD. (This is the default setting for Output 5.)
b.
Set Output 6 to Shot 7.
c.
Set Output 7 to Transmit (a Bilinx signal to the head end).
User Manual
Bosch Security Systems, Inc.
AutoDome 600 Series Analog PTZ Camera
4.
Advanced Features | en
43
Set up the Alarm Rule (for this example use Rule 1). Select the Inputs from the Rule
Setup menu:
5.
6.
a.
Select Rule 1.
b.
Set the first input to Alarm Input 1.
Select the outputs:
a.
Set the first output to OSD.
b.
Set the second output to Shot 7.
c.
Set the third output to Transmit.
Enable the rule:
–
Highlight Enabled and select YES.
Example 2: Advanced Alarm Rule
Scenario: A VG5 AutoDome located at an airport is set to AutoPan Between Limits from the
parking garage to the airport terminal. The gate entering the airport has an alarm contact
connected to the AutoDome, and the perimeter fence in the area of the gate has an infrared
(IR) motion detection sensor connected to the AutoDome.
When both the gate contact and motion detector alarms are activated at the same time, we
want the alarm rule to:
1.
Flash an OSD message (***ALARM 2***) on the monitor.
2.
Stop the AutoPan and move the camera to a saved position (Shot 5) viewing the fence.
3.
Turn on AutoTrack.
4.
Transmit a Bilinx signal to the head end system to trigger an alarm response.
The sequence to program this alarm rule example is as follows:
1.
Wire and set the alarm Input(s).
a.
Wire the motion detector to Input 1. (This circuit is normally open.)
b.
Wire the gate alarm contact to Input 5. (This circuit is normally closed.)
NOTICE!
For instruction on wiring alarm and relay connections, see the AutoDome Modular Camera
System Installation Manual.
2.
From the Inputs Setup menu:
a.
Ensure Input 1 (the motion detector) is set to N.O. (This setting is the default for
Input 1.)
b.
3.
a.
4.
6.
Set Output 6 to Transmit.
c.
Set Output 7 to Shot 5.
d.
Set Output 8 to AutoTrack.
Set up the Alarm Rule (for this example use Rule 2). Select the alarm Inputs:
From the Rule Setup menu select Rule 2.
b.
Set the first input to Alarm Input 1. (The motion detector.)
c.
Set the second input to Alarm Input 5. (The gate alarm contact.)
Select the alarm Outputs:
a.
Set the first output to OSD.
b.
Set the second output to Shot 5 viewing the fence.
c.
Set the third output to AutoTrack and select Latched.
d.
Set the fourth output to Transmit (a Bilinx signal to the headend).
Enable the alarm Rule:
–
Bosch Security Systems, Inc.
Set Output 5 to OSD.
b.
a.
5.
Ensure Input 5 (the gate contact) is set to N.C.
Set the alarm Outputs from the Outputs Setup menu:
Highlight Enabled and select YES.
User Manual
F.01U.215.781 | 1.0 | 2011.04
44
en | Advanced Features
AutoDome 600 Series Analog PTZ Camera
Example 3: Advanced Alarm Rule using AutoTrack
The following example explains how to set an alarm rule that moves the camera to a preset
position and then activates the AutoTrack feature to track an intruder after an alarm is
triggered. This example uses the Configuration Tool for Imaging Devices (CTFID) software
tool. Refer to the Configuration Tool for Imaging Devices User Guide, available at
www.boschsecurity.com.
1.
Launch the CTFID software from a computer that is connected to a VG5 AutoDome.
2.
Click the Online Config button and then expand Alarm.
3.
Expand Output Options; then click Output Option 5.
Figure 7.1
Figure 7.2
CTFID Overview Window
Expanded Alarm Group
4.
Select Tracking from the Type drop-down list.
5.
Click Output Option 6.
6.
Select Shot from the Type drop-down list.
F.01U.215.781 | 1.0 | 2011.04
User Manual
Bosch Security Systems, Inc.
AutoDome 600 Series Analog PTZ Camera
7.
Advanced Features | en
45
Type the number 1 or use the slide bar to specify shot number 1. (Shot numbers must be
set prior to configuring an alarm rule. See Section 3.2 Setting Preset Shots, page 25, for
instructions).
The AutoDome moves to this preposition when the alarm rule is true.
Figure 7.3 Output Option 6 Configuration
8.
Expand Alarm Rule; then click Alarm Rule 1.
9.
Click the Yes radio button to enable the rule.
10. Type the number 1 or use the slider bar to select 1 for the Input option.
11. Select Alarm Input 1 from the Input Option drop-down list.
12. Ensure that the Output number is set to 1.
13. Select Shot 1 from the Output Options drop-down list.
This option instructs the AutoDome to move to pre-position shot 1 when Input 1 is true.
Figure 7.4 Alarm Rule 1 Configuration
14. Move the Output slider bar to Output 2.
15. Select Tracking from the Output Option drop-down list.
This option instructs the AutoDome to activate the AutoTrack feature after the input
alarm is triggered and after the AutoDome moves to pre-position 1.
Bosch Security Systems, Inc.
User Manual
F.01U.215.781 | 1.0 | 2011.04
46
en | Advanced Features
AutoDome 600 Series Analog PTZ Camera
16. Select 5 sec from the Output Period drop-down list.
This option instructs the AutoDome to turn off the AutoTrack feature after five seconds
from when the tracked object is out of view.
7.2
AutoTrack Operation
The AutoDome features enhanced AutoTrack software with more versatility and smoother
object tracking. AutoTrack continuously follows an individual even if the person passes behind
a Privacy Mask. When used with Virtual Mask, it is able to ignore predefined areas of
background motion.
You can manually start AutoTrack or program the AutoDome to automatically turn on
AutoTrack.
–
Manual
–
Enter the keyboard command ON-78-ENTER.
–
In Pelco Mode, open the Main menu, select the Advanced menu, and then select
AutoTrack On.
–
Automatic
–
During a pre-position tour.
–
During AutoPan.
–
AutoDome activates AutoTrack after a period of Inactivity (Return to Scene 1 or
Return to Previous Aux), if AutoTrack is programmed for these activities.
NOTICE!
For proper operation AutoTrack requires that the camera height be set in the software. Open
the Bosch Main menu, select the Advanced menu and select Camera Height to enter the
height.
7.2.1
AutoTrack Settings and Recommendations
AutoTrack operates by recognizing an individual in motion and zooms-in to approximately 50%
of the field of view for an average target height of six feet. In addition to the camera height,
other factors may interfere with AutoTrack operation.
Setting the Camera Height
To ensure smooth tracking set the Camera Height accurately. Bosch recommends a minimum
camera height of 3.6 m (12 ft).
1.
Press OFF-90-ENTER to turn off the command lock.?
2.
Press ON-46-ENTER to access the Main Menu.?
3.
Use the joystick to highlight the Advanced menu.?
4.
Press Focus/Iris to open the menu.?
5.
Highlight the Camera Height option and press the Focus/Iris button.?
6.
Enter a value between 3.6 m (12 ft) and 30.7 m (100 ft).
7.
Press Focus/Iris again to accept the camera height value.
8.
Exit the Advanced menu; then exit the Main menu.
Ensuring Smooth AutoTrack Operation
Factors such as the viewing angle and unwanted motion (from trees, for example) may
interfere with AutoTrack operation. Use the following recommendations to ensure smooth
AutoTrack operation:
F.01U.215.781 | 1.0 | 2011.04
User Manual
Bosch Security Systems, Inc.
AutoDome 600 Series Analog PTZ Camera
–
Advanced Features | en
47
Mount/Mounting Surface Stability
–
Mount the camera in the most stable position. Avoid locations affected by vibrations,
such as those caused by a roof-top air conditioner. These vibrations may cause
complications when the camera zooms-in on a target.
–
Use the pendant arm mount, if possible. This mount option provides the most
–
Use guy wires to protect against strong winds if using the parapet mount.
stability for the camera.
–
Field of View
–
Select a location and viewing angle that allows the flow of people to move across
the camera’s field of view.
–
Avoid motion that moves directly towards the camera.
–
Avoid locations that attract large numbers of people, such as retail stores or
intersections.
–
Unwanted Motion
–
Use the Virtual Masking feature (see Section 7.3 Virtual Masking, page 48) to mask
unwanted motion from trees or cars.
Bosch recommends that you draw the virtual mask 10% larger than the object to be
masked.
–
Avoid neon lights, flashing lights, night time lights, and reflected light (from a
window or mirror, for example). The flickering of these lights can affect the
AutoTrack operation. Use a Virtual Mask to hide these type of lights if they cannot be
avoided.
–
Check the virtual mask periodically to ensure that it still covers the entire object to
be masked. Adjust the mask if necessary.
7.2.2
AutoTrack Optimization
The AutoDome achieves optimum tracking performance when the focal length of the lens
during AutoPan is as close to the focal length of the lens during an AutoTrack operation. The
ambient light conditions also affect the AutoTrack performance.
Dynamic Light Conditions
The ambient lighting conditions affect AutoTrack performance, especially in outdoor dynamic
lighting conditions that change daily or hourly. To optimize the AutoTrack performance under
changing light conditions, Bosch recommends that you configure the AutoTrack Sensitivity
and the AutoPan speeds.
Bosch recommends setting the AutoTrack Sensitivity to Auto and suggests the following
AutoPan speed for outdoor conditions:
Camera Focal Length
Maximum Suggested AutoPan Speed
(degrees/sec)
Near-field (Wide Angle)
5
Mid-field
2
Far-field (Telephoto)
1
If you need a higher AutoPan speed, set the AutoTrack Sensitivity to a value between 1 and 10
in the Advanced Feature Setup menu.
Bosch Security Systems, Inc.
User Manual
F.01U.215.781 | 1.0 | 2011.04
48
en | Advanced Features
AutoDome 600 Series Analog PTZ Camera
Setting AutoTrack Optimization Parameters
1.
Press OFF-90-ENTER to turn off the command lock.?
2.
Press ON-46-ENTER to access the Main Menu.?
3.
Use the joystick to highlight the Advanced menu.?
4.
Select the AutoTrack Sensitivity option and change the parameter to Auto or to a value
between 1–10.?
5.
Exit the AutoTrack Sensitivity menu. Then, exit the Advanced Feature Setup menu.
6.
Access the PTZ Setup menu.
7.
Select the AutoPan option and change the parameter to one of the suggested values in
the table above.
8.
Exit the AutoPan menu. Then, exit the PTZ Setup menu and finally exit the Main menu.
Consistent Light Conditions
You may use higher AutoPan speeds in consistent indoor or outdoor ambient light conditions,
but Bosch recommends not exceeding a speed of more than 15 degrees/sec. Then modify the
AutoTrack Sensitivity setting to reach the optimal results.
7.3
Virtual Masking
Virtual Masking is a unique Bosch technology that allows you to create an “invisible” area that
ignores unwanted background motion. These invisible masks are similar to privacy zones,
except that the AutoDome AutoTrack and Motion Detection algorithms can see them.
–
To configure a Virtual Mask, open the Main menu, select the Advanced menu, then select
–
In Pelco Mode, open the Main menu, select the Advanced menu, then select Virtual
Virtual Masking. To setup a Virtual Mask follow the on-screen menu instructions.
Masking. To setup a Virtual Mask follow the on-screen menu instructions.
NOTICE!
Draw the mask 10% larger than the object to ensure that the mask completely covers the
object as the AutoDome zooms in and out.
7.4
Privacy Masking
Privacy Masking is used to block out a specific area of a scene from being viewed. Mask
choices include black, white, or blurred, and can be configured with three, four, or five
corners to cover more complex shapes.
NOTICE!
Privacy Masking does not hinder AutoTrack from tracking an object.
–
To configure a Privacy Mask, open the Main menu, select Display Setup, and then select
Privacy Mask. Alternatively, enter the keyboard command ON-87-ENTER. To setup a
privacy mask, follow the on-screen menu instructions.
–
In Pelco Mode open the Pelco Main menu, open the Bosch menu, select the Display
Setup menu, and finally select Privacy Masking. To setup a privacy mask, follow the onscreen menu instructions.
NOTICE!
Draw the mask 10% larger than the object to ensure that the mask completely covers the
object as the AutoDome zooms in and out.
F.01U.215.781 | 1.0 | 2011.04
User Manual
Bosch Security Systems, Inc.
AutoDome 600 Series Analog PTZ Camera
7.5
Advanced Features | en
49
Motion Detection with Region of Interest
(Preset positions 90 through 99)
With the VG5 Series AutoDome, the motion detection software can be configured to create a
Region of Interest within multiple preset positions or scenes. It can take advantage of Virtual
Masking to ignore motion in predefined areas. Motion Detection can also be used as an Alarm
Rule input.
Preset positions 90 through 99 are reserved for programming motion detection scenes.
NOTICE!
Motion Detection always takes precedence over AutoTrack object tracking.
To set up a scene with Motion Detection:
1.
Choose an unused Preset position from 90 to 99. For this example use Preset scene 95.
2.
Enter the keyboard command SET-95-ENTER.
3.
Select YES at the Apply Motion Detection? prompt. (If NO is selected, the Preset scene
does not activate Motion Detection.)
4.
Select YES at the Apply Region of Interest? prompt. (If NO is selected, the entire scene is
used for Motion Detection.)
5.
Follow the on-screen menu instructions to construct the shape of the screen area you
want to detect motion within.
NOTICE! Up to five (5) anchor points can be used to form the area which you want to detect
motion within. Motion Detection is not activated until the Preset scene is recalled. The Motion
Detection icon "M" appears in the upper left-hand corner of the display.
7.6
Image Stabilization
Image Stabilization becomes increasingly important as zoom ranges are extended. The
advanced image stabilization algorithms of the VG5 Series AutoDome eliminate camera shake
for exceptional image clarity. Bosch achieves this clarity without reducing camera sensitivity
or picture quality.
–
To configure image stabilization, open the Main menu, select the Advanced menu, and
then select Stabilization to turn on the feature.
–
In Pelco Mode open the Main menu, select the Advanced menu, and then select
Stabilization to turn on the feature.
7.7
Pre-position Tour
The VG5 Series AutoDome features (2) preset tours. Each preset scene is saved for playback
later.
Tour 1 is a standard tour that only recalls the scenes in the exact sequence they were shot.
Scenes can be added or deleted on the tour, but the sequence cannot be changed. To add or
remove scenes on Tour 1 enter the keyboard command SHOT-900-ENTER and follow the onscreen instructions.
Tour 2 is a customizable tour that allows you to rearrange the sequence of scenes on the tour
by inserting and deleting scenes. To enter the Edit Tour 2 menu, enter the keyboard command
SET-900-ENTER and follow the on-screen instructions.
Bosch Security Systems, Inc.
User Manual
F.01U.215.781 | 1.0 | 2011.04
50
en | Advanced Features
7.8
AutoDome 600 Series Analog PTZ Camera
Azimuth, Elevation, and Compass Directions
The VG5 AutoDome allows a user to display the azimuth and elevation position, and the
compass heading of the camera. The AutoDome displays the position data in the lower-right
corner of the image display. These readings are described as:
Azimuth:
The pan angle from zero to 359 degrees in one degree increments. An azimuth
of zero degrees corresponds to North.
Elevation:
The tilt position from zero (horizon) to –90 degrees (camera pointing straight
down) in one degree increments.
Compass:
The cardinal or intercardinal (N, NE, E, SE, S, SW, W, NW) heading in which the
camera is pointing.
The AutoDome uses the azimuth to determine the compass direction. The following table
shows the azimuth range and its corresponding compass heading:
Azimuth Range
21° to 65°
66° to 110°
111° to 155°
156° to 200°
201° to 245°
246° to 290°
291° to 335°
336° to 20°
7.8.1
Compass Direction
NE (Northeast)
E (East)
SE (Southeast)
S (South)
SW (Southwest)
W (West)
NW (Northwest)
N (North)
Setting the Azimuth Zero Point
The installer must calibrate the Azimuth Zero point. The AutoDome uses the Azimuth Zero
point, usually set to magnetic North, as the zero degree pan position and as the North
compass heading. The AutoDome then displays the azimuth reading and the compass heading
based on the number of degrees from the Azimuth Zero point.
To set the Azimuth Zero point:
1.
Determine the North compass heading, then move the camera to that position.
2.
Press OFF-90-ENTER to turn off the command lock (if active).
3.
Press ON-94-ENTER to set the Azimuth Zero point.
CAUTION!
Bosch recommends that only the installer calibrate the Azimuth Zero point. A recalibration to
the Azimuth Zero point may cause inaccurate compass headings.
F.01U.215.781 | 1.0 | 2011.04
User Manual
Bosch Security Systems, Inc.
AutoDome 600 Series Analog PTZ Camera
7.8.2
Advanced Features | en
51
Displaying Azimuth, Elevation, and Compass Headings
You can display only the azimuth/elevation readings or only the compass reading, or you can
display both readings at the same time. The AutoDome displays the azimuth/elevation
readings and the compass heading in the following way:
180 / –45 S
where:
–
180 is the Azimuth or the pan location in degrees.
–
–45 is the Elevation or the tilt location in degrees.
–
S is the compass direction (cardinal or intercardinal).
1.
Press ON-95-ENTER to display the azimuth/elevation reading.
2.
Press ON-96-ENTER to display the compass heading.
3.
Press OFF-95-ENTER to hide the azimuth/elevation reading.
4.
Press OFF-96-ENTER to hide the compass heading.
Bosch Security Systems, Inc.
User Manual
F.01U.215.781 | 1.0 | 2011.04
52
en | Troubleshooting Guide
AutoDome 600 Series Analog PTZ Camera
8
Troubleshooting Guide
8.1
VG5 AutoDome Operation and Control
Problem
Solution
No video
–
Check that the Green LED on the AutoDome CPU board is on. This LED indicates video
from the camera.
If the Green LED is off, then:
–
Check that the Red LED on the AutoDome CPU board is slowly blinking. This LED
indicates power to the AutoDome power supply board and to the CPU Module.
Red LED on AutoDome CPU M0.odule
Flash SequenceIndicates:
–
5 sec. on / 0.5 sec. off: Normal operation
–
Steady on: CPU is locked
If the Red LED is on steady, then:
–
Try cycling the AutoDome power off and on.
If the Red LED is off, then:
If using a Bosch Pendant Power Supply Box:
–
Check that Green LED in Power Supply Box is on. This LED indicates mains power
through the transformer.
If the Green LED is off, then:
–
Turn off the Power.
–
Check the FX101 fuse for mains power to the Power Supply Box.
If O.K., then:
–
Check the FX102 fuse for 24 V power to the AutoDome Pendant.
If O.K., then:
If using a non-Bosch power supply:
–
Check that the mains power to the power supply box is on.
If O.K., then:
–
Check that there is 24 V output from the transformer.
–
Check the connector on top of the AutoDome housing for bent pins.
If O.K., then:
–
Check the integrity of all wires and terminal connections to the AutoDome.
If O.K., then:
If there is power to the AutoDome, then:
–
Remove the camera and CPU modules from the AutoDome housing and check that the
Green LED on the housing power supply board is on.
If the Green LED is off, then:
–
F.01U.215.781 | 1.0 | 2011.04
Check that the fuse on the housing power supply board is good.
User Manual
Bosch Security Systems, Inc.
AutoDome 600 Series Analog PTZ Camera
No camera control
–
Troubleshooting Guide | en
53
Ensure that the keyboard and monitor are set to the correct (same) camera number.
If O.K., then:
–
Check that the camera address is properly set. Enter ON-997-ENTER to display the
camera address.
If address is not set or is incorrect, then:
–
Set the camera address using FastAddress (ON-998-ENTER).
If O.K., then:
–
Check that the Amber LED on the AutoDome CPU turns on when receiving pan/tilt
commands from the controller keyboard. The Amber LED indicates control is being
received.
Amber LED on AutoDome CPU Module
Flash Sequence
–
Off
No incoming communications or no power
–
Solid for 2 seconds
Receiving good data
–
Fast blinking
Lost packet(s)
If amber LED does not light when given PTZ commands, then:
–
Check if other cameras on the system can be controlled. If not, check the controller
and wiring connections.
If O.K., then:
–
Check that the RS-232/485 selector switch is properly set to the proper protocol.
If O.K., then:
–
Ensure that all Biphase, Bilinx, or RS-232/485 wires are properly connected. See the
VG5 AutoDome Installation Manual.
If O.K., then:
–
Check if you can access the AutoDome OSD menus (ON-46-ENTER).
If O.K., then:
–
Confirm that the AutoDome passes homing (SET-110-ENTER).
If AutoDome fails homing, then:
Intermittent camera
–
Contact Bosch Technical Support.
–
Check that only the last AutoDome in a daisy chain configuration is terminated with a
control
100 Ω resistor across the +/- biphase terminals.
If O.K., then:
–
Check that the maximum wire distance has not been exceeded for the control protocol
(the maximum distance for RS-232 is 50 feet). See the VG5 AutoDome Installation
Manual.
If O.K., then:
–
Check that all wiring meets Bosch recommended standards and specifications. See the
VG5 AutoDome Installation Manual.
Camera moves when –
Check that the camera address is properly set (ON-997-ENTER). If the camera address
moving other
is not set, the AutoDome responds to control commands to any camera on the system.
cameras
Cannot access user
If camera address is not set, then:
–
Invoke the FastAddress Menu to assign a camera address (ON-998-ENTER).
–
Enter the unlock command OFF-90-ENTER. This command may require a password.
settings
Bosch Security Systems, Inc.
(Commands automatically lock in 30 minutes.)
User Manual
F.01U.215.781 | 1.0 | 2011.04
54
en | Troubleshooting Guide
AutoDome 600 Series Analog PTZ Camera
Setting FastAddress
The FastAddress value must match the Unique Identifier for the AutoDome. To set the
with an American
FastAddress on an American Dynamics keyboard refer to Section 4.1 Setting FastAddress
Dynamics Keyboard
with Alternative Protocols, page 28.
Picture is dark
–
Check that the Gain Control is set to AUTO (ON-43-ENTER).
If O.K., then:
–
Check that the Auto Iris Level is set to the appropriate level (ON-11-ENTER).
If O.K., then:
–
Check that the video coax is terminated with 75 Ω only at the head end. (Double
termination causes dark video.)
If O.K., then:
–
Go to the Camera Setup Menu and increase the Pre-Compensation setting.
If O.K., then:
–
Check that the camera lens cover is removed.
If O.K., then:
–
Check that the maximum coax distance has not been exceeded. See the VG5 AutoDome
Installation Manual.
If O.K., then:
–
Restore all camera settings (ON-40-ENTER).
Colors are not
–
Reset the White Balance to the appropriate selection (ON-30-ENTER).
correct
If O.K., then:
–
Go to the Camera Setup Menu and increase the Pre-Compensation setting.
If O.K., then:
–
Check that the maximum coax distance has not been exceeded. See the VG5 AutoDome
Installation Manual.
If O.K., then:
–
Restore the default settings (ON-40-ENTER).
–
Turn on backlight compensation (ON-20-ENTER).
Video is rolling,
–
Ensure that the Synch Mode is set to Internal (OFF-42-ENTER).
noisy or distorted
If O.K., then:
Background is too
bright to see subject
–
Check that the maximum coax distance has not been exceeded. See the VG5 AutoDome
Installation Manual.
If O.K., then:
–
Check the integrity of all BNC connectors and splices.
Note: Connecting a network cable to the interface board of a non-IP AutoDome causes
video distortion.
–
Remove the network cable from the interface board RJ-45 connector.
If O.K., then:
–
Contact Bosch Technical Support.
Day/Night camera
–
Check that the Day/Night mode is set to AUTO (ON-56-ENTER).
does not switch
If O.K., then:
automatically when
–
Set Gain Control to AUTO (ON-43-ENTER).
image is dark
F.01U.215.781 | 1.0 | 2011.04
User Manual
Bosch Security Systems, Inc.
AutoDome 600 Series Analog PTZ Camera
Troubleshooting Guide | en
55
Inside of Outdoor
–
Pendant bubble is
If status reports Heater No Power, then:
Check the status of the Heater Module (ON-66-ENTER).
foggy
–
Turn off the power to the AutDome.
–
Check the FX103 fuse in the Power Supply Box for power (24 V) to the heater module.
If O.K., then:
–
Check all wiring and connector pins to the heater module.
Low Voltage flashing –
If using a non-Bosch power supply, confirm that it meets the Bosch AutoDome power
on monitor display
ratings. See the AutoDome Datasheet for specifications.
If O.K., then:
–
Check the mains input line voltage.
If O.K., then:
–
Check that the maximum wire length from the power supply has not been exceeded.
See the VG5 AutoDome Installation Manual.
If O.K., then:
–
Measure the AC voltage input to the camera while power is applied to the camera. The
voltage must be ≥ 21 VAC to stop the message.
Bosch Security Systems, Inc.
User Manual
F.01U.215.781 | 1.0 | 2011.04
56
8.2
en | Troubleshooting Guide
AutoDome 600 Series Analog PTZ Camera
VG5 Series AutoDome Audio
The following diagram illustrates the path for audio transmissions between a microphone/
AutoDome and a computer that plays the audio.
Audio Connections with an VG5 600 Series AutoDome
In this illustration the VG5 600 Series AutoDome connects to a Bosch Video/Audio IP Encoder
via a coaxial cable. The computer that plays the audio is connected to the encoder via an
Ethernet cable.
Figure 8.1
Typical Audio Connections for an Analog AutoDome
1
Microphone
6
Audio In
2
Coaxial Connection; Microphone to Bosch 7
Video In
Video/Audio Encoder;
10 m (33 ft) maximum distance
3
VG5 600 Series AutoDome
8
Ethernet Connection;
Bosch Video/Audio Encoder to a PC
4
Coaxial Connection; VG5 600 Series
9
Computer with Bosch DiBos Software
Autodome to a Bosch Video/Audio
Encoder
5
F.01U.215.781 | 1.0 | 2011.04
Bosch Video/Audio Encoder
User Manual
Bosch Security Systems, Inc.
AutoDome 600 Series Analog PTZ Camera
Problem
Solution
No Audio
–
Troubleshooting Guide | en
57
Check the computer receiving the audio from the VG5 AutoDome or from the IP
Encoder.
–
Check the computer’s audio settings. Ensure that the sound levels are at an audible
level.
–
Check the computer’s audio output card and speakers. Play a secondary source of
audio on the computer. If you still do not hear audio replace the speakers and try
again.
If O.K., then:
–
Ensure that the Audio option is enabled for the IP device.
a.
Access the Settings Web page for the IP-enabled device.
b.
Expand the Encoder Settings link, then click Audio Settings.
c.
Ensure that On is selected from the Enable Audio drop-down list. Then, click Set.
If O.K., then:
–
Check the microphone.
Connect appropriate speakers directly to the microphone at the camera site and
confirm that the audio is clear and audible at the location.
An audio problem or noise at the source will further degrade as it travels through all the
cables and connections.
If O.K., then:
–
Verify the cable type and installation used for audio connections between the
microphone and the VG5 AutoDome.
–
Cable type: Coaxial
–
Cable length: 10 m (33 ft), maximum
Refer to the VG5 AutoDome Installation Manual for more information.
Bosch Security Systems, Inc.
User Manual
F.01U.215.781 | 1.0 | 2011.04
58
en | Troubleshooting Guide
Problem
AutoDome 600 Series Analog PTZ Camera
Solution
If O.K., then:
–
Check all network connections.
–
If the video is clear and contains no distortion, then the network connections are
probably not the source of audio problems.
–
Ensure that the maximum distance between any two Ethernet connections is 100 m
(328 ft).
Refer to the VG5 AutoDome Installation Manual for more information.
Poor Audio
–
Check the computer receiving the audio from the VG5 AutoDome or from the IP
Decoder.
–
Check the computer’s audio output card and speakers. Play a secondary source of
audio on the computer, if you hear static then replace the speakers and try again.
–
Check the computer’s audio output card and speakers. Play a secondary source of
audio on the computer. If you still do not hear audio replace the speakers and try
again.
If O.K., then:
–
Check the Gain settings and the peak gain value.
a.
Access the Settings Web page for the IP-enabled device.
b.
Expand the Encoder Settings link, then click Audio Settings.
c.
Adjust the Gain level so that the peak value stays within the green area.
Refer to the VG5 AutoDome Installation Manual for complete information.
If O.K., then:
–
Check the location of the microphone and the audio cables.
–
Line level audio is typically between 700 mV and 2 V so it may be affected by AC
–
Ensure that there is a maximum (at least 1 foot per 100 VAC) distance between the
power or transmission sources.
microphone and audio cables and the AC source.
If O.K., then:
–
Verify the cable type and installation used for audio connections between the
microphone and the VG5 AutoDome.
–
Cable type: Coaxial
–
Cable length: 10 m (33 ft), maximum
Refer to the VG5 AutoDome Installation Manual for more information.
F.01U.215.781 | 1.0 | 2011.04
User Manual
Bosch Security Systems, Inc.
AutoDome 600 Series Analog PTZ Camera
9
User Command Table | en
User Command Table
Function
Comm
Key
No.
On/Off
On/Off
Command
Description
1
Scan 360°
Autopan without limits
2
Autopan
Autopan between limits
On/Off
7
Play Custom Pre-position Tour
Activate/Deactivate
On/Off
8
Play Pre-position Tour
Activate/Deactivate
On/Off
14
Set Autopan and Scan Speed
Enters speed adjustment slide bar
On/Off
15
Set Pre-position Tour Period (dwell)
Enters dwell adjustment slide bar
On/Off
20
Backlight Comp
Backlight Compensation
On/Off
24
Stabilization
Electronic Stabilization
On/Off
26
Wide Dynamic Range
Activate/Deactivate
On
47
View Factory Settings
View all menu default settings
On/Off
50
Playback A, continuous
Activate/Deactivate
On/Off
51
Playback A, single
Activate/Deactivate
On/Off
52
Playback B, continuous
Activate/Deactivate
On/Off
53
Playback B, single
Activate/Deactivate
On/Off
56
Night Mode Menu
On, Off, Auto (Day/Night only)
On/Off
57
Night Mode Setting
Enables/Disables Night Mode (Day/Night only)
On
62
Pre-position Title Menu
Enters Pre-position Title menu
On
64
Alarm Status
Enters Alarm Status menu
Off
65
Alarm Acknowledge
Acknowledge alarm or deactivate physical outputs
On
66
Display Software Version
Displays software version number
On
72
Re-initialize Camera
Performs camera/lens re-initialization functions
On/Off
78
AutoTrack
Turns AutoTrack on or off
On/Off
81
On/Off
On/Off
On/Off
On/Off
59
82
83
84
89
Alarm Output 1
On–Activates output
Open Collector
Off–Deactivates output
Alarm Output 2
On–Activates output
Open Collector
Off–Deactivates output
Alarm Output 3
On–Activates output
Open Collector
Off–Deactivates output
Alarm Output 4
On–Activates output
Relay
Off–Deactivates output
Preposition Confirmation
On–Issues a message that prompts for approval to
overwrite a preposition
Off–No confirmation message issued
On/Off
90
Command Lock/Unlock
On–Lock on
Off–Lock off
On/Off
95
Display Azimuth/Elevation Readings
On–Displays azimuth/elevation readings
Off–Hides azimuth/elevation readings
On/Off
96
Display Compass Heading
On–Displays compass heading
Off–Hides compass heading
On/Off
100
Record A
Activate/Deactivate
On/Off
101
Record B
Activate/Deactivate
Bosch Security Systems, Inc.
User Manual
F.01U.215.781 | 1.0 | 2011.04
60
en | User Command Table
Function
Comm
Key
No.
On
AutoDome 600 Series Analog PTZ Camera
Command
Description
997
FastAddress, display
Display current address
On
998
FastAddress, all units
Display and program current address
On
999
FastAddress, unaddressed domes
Display and program unaddressed AutoDomes
Set
“1-99”
Pre-position Programming
Set ##–Programs a preset view
Shot
“1-99”
Pre-position Recall
Shot ##–Recall programmed preset
Set
100
Pre-position Menu
Enters the Pre-position menu
Set/Shot 101
Autopan Left Limit
Set–Programs left limit
Shot–Shows limit
Set/Shot 102
Autopan Right Limit
Set–Programs right limit
Shot–Shows limit
Set
110
Factory P/T Home Position
Set–Recalibrate home position
Set
900
Edit Tour 1 (Standard)
Enters the Standard Tour Scene menu
Shot
900
Edit Tour 2 (Custom)
Enters the Custom Tour Scene menu
Adds/Removes a Preposition Shot from
Set ###–Adds preset
Tour 1
Shot ###–Removes preset
Set/Shot 901-999
F.01U.215.781 | 1.0 | 2011.04
User Manual
Bosch Security Systems, Inc.
AutoDome 600 Series Analog PTZ Camera
A
| en
61
Appendix: FastAddress Conversions
Sample: If there is video coming from Camera #131, look at the appropriate conversion table
below to convert the FastAddress accordingly (i.e. using an AD system 131=3 and using a
Sensormatic system 131=32). Ensure that the camera number displayed within the menu on
the keyboard represents the converted camera number.
BLOCK 1
Bosch AD
BLOCK 2
Bosch AD
BLOCK 3
Bosch AD
BLOCK 4
Bosch AD
BLOCK 5
Bosch AD
BLOCK 6
Bosch AD
BLOCK 7
Bosc AD
BLOCK 8
Bosc AD
1
2
3
4
5
6
7
8
9
10-64
65
66
67
68
69
70
71
72
73
74-
129
130
131
132
133
134
135
136
137
138-
193
194
195
196
197
198
199
200
201
202-
257
258
259
260
261
262
263
264
265
266-
321
322
323
324
325
326
327
328
329
330-
h
385
386
387
388
389
390
391
392
393
394-
h
449
450
451
452
453
454
455
456
457
458-
1
2
3
4
5
6
7
8
9
10-64
1
2
3
4
5
6
7
8
9
10-64
128
Table 1.1
192
1
2
3
4
5
6
7
8
9
10-64
256
1
2
3
4
5
6
7
8
9
10-64
1
2
3
4
5
6
7
8
9
10-64
1
2
3
4
5
6
7
8
9
10-64
320
384
448
512
1
2
3
4
5
6
7
8
9
10-64
Address Conversion Table for AD/Manchester Systems
Group 1
IN
OUT
1
1
2
2
3
3
4
4
5
5
6
6
7
7
8
8
9
9
10-99 10-99
Table 1.2
1
2
3
4
5
6
7
8
9
10-64
Group 2
IN
OUT
100
1
101
2
102
3
103
4
104
5
105
6
106
7
107
8
108
9
109- 10-99
Group 3
IN
OUT
199
1
200
2
201
3
202
4
203
5
204
6
205
7
206
8
207
9
208- 10-99
Group 4
IN
OUT
298
1
299
2
300
3
301
4
302
5
303
6
304
7
305
8
306
9
307- 10-99
Group 5
IN
OUT
397
1
398
2
399
3
400
4
401
5
402
6
403
7
404
8
405
9
406- 10-99
Group 6
IN
OUT
496
1
497
2
498
3
499
4
500
5
501
6
502
7
503
8
504
9
505- 10-99
Group 7
IN
OUT
595 1
596 2
597 3
598 4
599 5
600 6
601 7
602 8
603 9
604- 10-99
Group 8
IN
OUT
694 1
695 2
696 3
697 4
698 5
699 6
700 7
701 8
702 9
703- 10-99
198
297
396
495
594
693
792
Address Conversion Table for AD/Sensormatic RS-422 Systems
Bosch Security Systems, Inc.
User Manual
F.01U.215.781 | 1.0 | 2011.04
62
en | Index
AutoDome 600 Series Analog PTZ Camera
Index
Symbols
#-ENTER 7
Numerics
33-PRESET
34-PRESET
80-PRESET
81-PRESET
82-PRESET
92-PRESET
93-PRESET
94-PRESET
95-PRESET
96-PRESET
97-PRESET
98-PRESET
99-PRESET
34
34
34
34
34
34
34
34
34, 35
34
34
34
34
A
ack 36, 38
acknowledge 36
acknowledge alarm 38
adjusting
AutoDome orientation 14
brightness 15
camera height 22
vertical position 15
Advanced Feature Setup menu 10, 21
camera height 22
virtual masking 22
AES 12
alarm relay 19
alarm rule 42
Alarm Setup menu 10, 17
AutoTrack 18
Aux Off 18
Aux On 18
input setup 18
inputs (1-7) 18
inputs (8-12) 18
motion detection 18
normally closed supervised contact 18
normally open dry contact 18
normally open supervised contact 18
Shot 18
alarm status 23
American Dyamics
FastAddress 28
American Dynamics 28
audio
cable 57
gain 58
line level 58
microphone 57, 58
quality 57, 58
auto focus 13
auto iris 13
auto iris level 13
Auto SensUP 12
autobaud 17, 32
F.01U.215.781 | 1.0 | 2011.04
AutoDome
orientation 14
automatic white balance 11
AutoPan 47
autopan 14, 25
AutoPivot 14, 35, 38
AutoScan 14, 34
AutoSensUP maximum 12
AutoTrack 18, 19, 46
camera height 46
field of view recommendations 47
light conditions 47
mount recommendations 46
optimization 47
sensitivity 47
settings 46
with AutoPan 47
Aux Off 6
Aux Off command 18, 19
Aux On 6
Aux On command 18, 19
AWB hold 11
azimuth 15, 50
Azimuth Zero 14
azimuth zero 50
B
backlight compensation 11
baud rate 17
Bilinx 17
BIST 23
Bosch menu 35, 36
built-in self test 23
C
camera
height 22
OSD 15
setup 35
camera height 46
Camera Setup menu 9, 10, 37
AutoSensUp maximum 12
AWB hold 11
backlight compensation 11
color 12
crystal 11
extended ATW 11
gain control 11
indoor white balance 11
line lock 11
line lock delay 11
maximum gain level 11
night mode 12
outdoor white balance 11
pre-compensation 12
sharpness 11
shutter 12
synchronization menu 11
threshold 12
white balance 11
Command key 6
User Manual
Bosch Security Systems, Inc.
AutoDome 600 Series Analog PTZ Camera
command lock 35
Command Lock menu 36
commands
#-ENTER 7
33-PRESET 34
34-PRESET 34
80-PRESET 34
81-PRESET 34
82-PRESET 34
92-PRESET 34
93-PRESET 34
94-PRESET 34
95-PRESET 34, 35
96-PRESET 34
97-PRESET 34
98-PRESET 34
99-PRESET 34
autopan 25
AutoScan 34
Aux Off 6, 18, 19
Aux On 6, 18, 19
clear 25
FastAddress 34
inactivity operation 27
keyboard 39
limit stops 34
OFF-90-ENTER 8, 27
ON-997-ENTER 7
ON-998-ENTER 7
ON-999-ENTER 7
ON-9-ENTER 27
Pelco 33
Pelco frame scan 34
PRESET 33
preset shot 25
preset tour 34
random scan 34
recording tours 27
Set 25
Set Shot 6
SET-100-ENTER 25
SET-802-ENTER 8
Shot 18, 25
Show Shot 6
store 25
synchronization mode 34
unlocked 25
user commands 25
zero pan 34
Communication Setup menu 10, 16
autobaud 17
baud rate 17
Bilinx 17
compass 15, 50
Configuration Tool for Imaging Devices 23
configuring
alarms 10
camera height 22
rules 20
constant focus 13
constant iris 13
CTFID 23
Bosch Security Systems, Inc.
Index | en
63
custom tour
editing 26
setting dwell time 26
Tour Period menu 26
custom tour 2 26
D
defining
command outputs 19
input commands 18
physical inputs 18
physical outputs 19
rules 20
diagnostics 23
Diagnostics menu 10, 22
alarm status 23
BIST 23
CTFID access 23
high temperature events 23
homing events 23
homing failed 23
internal temperature 23
low temperature events 23
low volt events 23
power up events 23
restart events 23
security access 23
video loss events 23
digital zoom 13
display adjust 15
Display Setup menu 10, 15
azimuth 15
camera OSD 15
compass 15
display adjust 15
Elevation 15
privacy masking 16
sector blanking 16
title OSD 15
displaying
camera response information 15
sector titles 15
shot titles 15
software version 38
titles 15
dwell period 26
dwell time 14
E
editing
custom tour 38
password 35, 38
presets 38
standard tour 38
Elevation 15
elevation 50
Enter key 6
extended ATW 11
User Manual
F.01U.215.781 | 1.0 | 2011.04
64
en | Index
F
AutoDome 600 Series Analog PTZ Camera
FastAddress 7, 28, 31, 34, 35, 38
setting with a Pelco Controller 31
setting with an American Dynamics Controller 28
with American Dynamic protocol 28
with Pelco protocol 28
FastAddress with Sensormatic protocol 28
focus speed 13
Function key 6
G
gain 11, 58
gain control
maximum level 11
H
high temperature
events 23
threshold 23
homing 5
events 23
failed 23
I
image stabilization 49
inactivity 14
accessing 27
mode 27
operation 27
period 14
Inactivity Mode menu 27
indoor white balance 11
input commands 18
inputs (1-7) 18
inputs (8-12) 18
inputs setup 18
internal temperature 23
iris speed 13
K
keyboard commands 39
#-ENTER 7
Aux Off 6, 18, 19
Aux On 6, 18, 19
Command key 6
Enter key 6
Function key 6
OFF-90-ENTER 8, 27
ON-997-ENTER 7
ON-998-ENTER 7
ON-999-ENTER 7
ON-9-ENTER 27
Set 25
Set Shot 6
SET-100-ENTER 25
SET-802-ENTER 8
Shot 25
Shot Shot 6
F.01U.215.781 | 1.0 | 2011.04
L
Language menu 10, 21
Lens Setup menu 9, 12
auto focus 13
auto iris 13
auto iris level 13
constant focus 13
constant iris 13
digital zoom 13
focus speed 13
iris speed 13
manual focus 13
manual iris 13
maximum zoom speed 13
spot focus 13
light conditions 47
limit stops 34, 35, 38
line level 58
line lock 11, 34
low temperature
events 23
threshold 23
low volt events 23
M
Manchester 28
manual
focus 13
iris 13
masking
privacy 16
virtual 22
maximum zoom speed 13
menus
Advanced Feature Setup 10, 21
Alarm Setup 17
Bosch 36
Camera Setup 10, 37
Command Lock 36
Communication Setup 16
Diagnostics 22
Display Setup 15
Inactivity Mode 27
Language 21
Lens Setup 12
Other 38
other 38
Outputs Setup 18
Pelco 28, 35
Setup 28
Pelco Setup 34
PTZ Setup 13, 37
Rule Setup 19
Setup 35, 36
Tour Period 26
microphone 57, 58
motion detection 18, 49
User Manual
Bosch Security Systems, Inc.
AutoDome 600 Series Analog PTZ Camera
N
networking
baud rate 17
night mode 12, 37
color 12
threshold 12
normally closed circuit 19
normally closed supervised contact 18
normally open circuit 19
normally open dry contact 18
normally open supervised contact 18
O
OFF-90-ENTER 8, 27
ON-997-ENTER 7
ON-998-ENTER 7
ON-999-ENTER 7
ON-9-ENTER 27
on-screen display 9, 15, 19
OSD 9, 15, 19
outdoor white balance 11
outputs (1-3) 19
outputs (5-12) 19
Outputs Setup menu 18
alarm relay 19
AutoTrack 19
Aux Off 19
Aux On 19
normally closed circuit 19
normally open circuit 19
OSD 19
outputs (1-3) 19
outputs (5-12) 19
transmit 19
P
passwords
changing 8
security level 8
special 8
peak gain 58
Pelco 28, 32, 35
Bosch 36
Command Lock 36
FastAddress 31
frame scan 34
keyboard commands 33
menus 28, 35
mode 32
night mode 37
PRESET command 33
protocol 32
PTZ Setup menu 35
random scan 34
Setup 35
Setup menu 34
software version 36, 38
white balance 37
Bosch Security Systems, Inc.
Index | en
65
Pelco keyboard commands
33-PRESET 34
34-PRESET 34
80-PRESET 34
81-PRESET 34
82-PRESET 34
92-PRESET 34
93-PRESET 34
94-PRESET 34
95-PRESET 34, 35
96-PRESET 34
97-PRESET 34
98-PRESET 34
99-PRESET 34
AutoScan 34
FastAddress 34
frame scan 34
limit stops 34
PRESET 33
preset tour 34
random scan 34
synchronization mode 34
zero pan 34
Pelco menu
Camera Setup 37
Other 38
PTZ Setup 37
Setup 28
Pelco menus
Other 38
Pelco Other menu
ack 38
acknowledge alarm 38
FastAddress 38
password 38
reset alarm 38
Pelco protocol
address guidelines 31
Pelco-D 32
Pelco-P 32
Pelco PTZ menu
AutoPivot 38
PTZ Setup
custom tour 38
Pelco PTZ Setup menu
edit standard tour 38
limit stops 38
presets 38
recordings 38
scan speed 38
Pelco Setup menu
ack alarm 36
Bosch menu 35
camera setup 35
command lock 35
FastAddress 35
password 35
reset alarm 36
Pelco-D 32
Pelco-P 32
physical inputs 18
User Manual
F.01U.215.781 | 1.0 | 2011.04
66
en | Index
playback
Recording A 27
Recording B 27
power up events 23
pre-compensation 12
Preposition Tour
custom 26
freeze frame 14
standard 26
preset shot 25
preset tour 34
previous Aux 14
privacy masking 16, 48
protocol
alternative 28
American Dynamics 28
Bilinx 17
Manchester 28
Pelco 32
Pelco-D 32
Pelco-P 32
RS-422 28
Sensormatic 28
PTZ
fixed speed 14
setup 9, 35
PTZ Setup menu 13, 14, 37
AutoDome orientation 14
autopan 14
AutoPivot 14
AutoScan 14
Azimuth Zero 14
freeze frame on preposition 14
inactivity 14
inactivity period 14
previous Aux 14
PTZ fixed speed 14
scene 1 14
tilt up limit 14
R
record 38
tour 27
tour A 27
tour B 27
Recording A 27
playback 27
Recording B
playback 27
region of interest 49
reset alarm 36, 38
restart events 23
RS-422 28
F.01U.215.781 | 1.0 | 2011.04
AutoDome 600 Series Analog PTZ Camera
rule
alarm relay 20
Aux Off 20
Aux On 20
enabled 20
follows 20
input 20
OSD 20
output 20
Shot 20
status 20
transmit 20
rule (1-12) 20
rule input
Shot 20
Rule Setup menu 19, 20
rules 20
S
scan speed 35, 38
scene 1 14
sector blanking 16
security
access 23
level 8
Sensormatic 28
SensUp 12
Set 6
Set command 25
Set Shot 6
SET-100-ENTER 25
SET-802-ENTER 8
settings
AutoDome orientation 14
autopan 25
brightness 15
camera height 22
inactivity mode 27
passwords 8
Preposition Tour 26
preset shot 25
rules 20
sharpness 11
vertical position 15
Setup menu 9, 28, 34, 35, 36
Advanced Feature Setup 10
Alarms 10
Camera 9
Communication 10
Diagnostics 10
Display 10
Language 10
Lens 9
PTZ 9
sharpness 11
Shot 6
clear 25
Set 25
store 25
view 25
Show 6
Show Shot 6
User Manual
Bosch Security Systems, Inc.
AutoDome 600 Series Analog PTZ Camera
Index | en
67
shutter 12
shutter mode 12
software
version 36
software version 38
spot focus 13
stabilization 49
standard tour
setting dwell time 26
Tour Period menu 26
synchronization mode 11, 34
T
tilt up limit 14
titles
brightness 15
OSD 15
vertical position 15
tour
custom 38
periods 35, 38
preposition 26
preset 34
standard 38
stopping 26
tour 1 26
tour 2 26
Tour 1
period 14
Tour 2
period 14
Tour Period menu 26
U
user commands 25
V
video loss events 23
virtual masking 22, 48
voltage limit 23
W
white balance 11, 37
Z
zero pan 34
Bosch Security Systems, Inc.
User Manual
F.01U.215.781 | 1.0 | 2011.04
68
en | Index
F.01U.215.781 | 1.0 | 2011.04
AutoDome 600 Series Analog PTZ Camera
User Manual
Bosch Security Systems, Inc.
AutoDome 600 Series Analog PTZ Camera
Bosch Security Systems, Inc.
Index | en
User Manual
69
F.01U.215.781 | 1.0 | 2011.04
70
en | Index
F.01U.215.781 | 1.0 | 2011.04
AutoDome 600 Series Analog PTZ Camera
User Manual
Bosch Security Systems, Inc.
Bosch Security Systems, Inc.
850 Greenfield Road
Lancaster, PA
U.S.A.
www.boschsecurity.com
© Bosch Security Systems, Inc., 2011
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertisement