User manual - Elite Alarm Solutions LLP

User manual - Elite Alarm Solutions LLP
GSM CONTROL SYSTEM
ESIM252
User Manual v1.0
Safety instructions
Please read and follow these safety guidelines and assembly instructions in order to maintain safety of operators and people around:
•
•
•
•
•
•
•
GSM control system Esim252 (further referenced as the system) contains an integrated radio transceiver operating in GSM
850/900/1800/1900 MHz bands.
Don’t use the system where it can interfere with other devices and cause any potential danger.
Don’t mount the system next to medical equipment or devices, if they require so.
Don’t use the system in hazardous environment.
Don’t expose the system to high humidity, chemical environment or mechanical impacts.
Don’t attempt to personally repair the system.
System label is on the bottom side of the device.
System Esim252 is a device mounted in limited access areas. Any system repairs must be done only by qualified, safety aware
personnel.
Mains power must be disconnected before any installation or tuning work starts. The system installation or maintenance
must not be done during stormy conditions.
The system must be powered by main 10-24V 50Hz ~200mA AC or 10-24V
200mA DC power supply which must be
approved by LST EN 60950-1 standard and be easily accessible nearby the device. When connecting the power supply to the
system, switching the terminals places does not have any affect.
Any additional devices linked to the system Esim252 (computer, sensors, relays etc.) must be approved by LST EN 60950-1
standard.
External power supply can be connected to AC mains only inside
installation room with automatic 2-pole circuit breaker capable of
disconnecting circuit in the event of short circuit or over-current
condition. Open circuit breaker must have a gap between connections of more than 3mm and the disconnection current 5A.
Phase
Null
PE
AC/DC
AC 230V
50 Hz/DC 24V
ESIM252
USB cable
Fuse F1 model MINISMDC050F 0.5A Blown fuse cannot be replaced by the user and the replacement fuses have to be exactly the
same as indicated by the manufacturer.
The device is fully turned off by disconnecting 2-pole switch off device of the external power supply or any other linked
device that the system Esim252 is powered from.
If you use I security class computer for setting the parameters it must be connected to earth.
The WEEE (Waste Electrical and Electronic Equipment) marking on this product or its documentation indicates that in the EU the
product must not be disposed of together with household waste.
Copyright © “ELDES UAB”, 2009. All rights reserved.
It is strictly forbidden to copy and distribute information in this document or pass to a third party without an advanced written authorization from “ELDES
UAB”. “ELDES UAB” reserves the right to update or modify this document and/or related products without a warning. Hereby, ELDES UAB declares that this
GSM CONTROL SYSTEM Esim252 is in compliance with the essential requirements and other relevant provisions of Directive 1999/5/EC. The declaration of
conformity may be consulted at www.eldes.lt
Limited Liability
The buyer must agree that the system will reduce
the risk of fire, theft, burglary or other dangers but
does not guarantee against such events.
“ELDES UAB” will not take any responsibility regarding personal, property or revenue loss while using
the system.
“ELDES UAB” responsibility according to local laws
does not exceed value of the purchased system.
“ELDES UAB” is not affiliated with GSM operators
providing cellular services therefore is not responsible for the quality of cellular services.
Manufacturer Warranty
The system carries a 24-month warranty by the manufacturer “ELDES UAB”.
Warranty period starts from the day the system has
been purchased by the end user. The warranty is
valid only if the system has been used as intended,
following all guidelines listed in the manual and
within specified operating conditions. Receipt with
purchase date must be kept as a proof.
The warranty is voided if the system has been
exposed to mechanical impacts, chemicals, high
humidity, fluids, corrosive and hazardous environment or other force majeure factors.
Package Content:
The system Esim252.................... 1 pcs
Esim252 user manual.................. 1 pcs
GSM antenna................................. 1 pcs
Fastening holders......................... 3 pcs
About User Manual
This document describes GSM control system
Esim252, its operation and installation.
It is very important to read User Manual before
start using the system.
A quick start guide is located in first two chapters.
Chapter 3 and 4 describe additional system capabilities.
CONTENT
1. General Information
1.1 1.2 1.3 1.4 1.5 1.6
Function........................................................................................................4
Operation Description..............................................................................4
Technical Specifications ..........................................................................5
Connector Functionality..........................................................................5
Connection Circuit.....................................................................................6
System Installation....................................................................................7
2. System Pre-operation and the Main Control Commands
2.1 2.2 2.3 2.4 Selecting device language
and verification of SMS central number............................................8
Password Change ......................................................................................8
User Numbers..............................................................................................9
2.3.1 Saving or Changing Numbers ...............................................9
2.3.2 Verification of Saved Numbers..............................................9
2.3.3 Deletion of Saved Numbers. ..................................................9
Date and Time Settings ...........................................................................9
3. Additional System Capabilities
3.1 Renaming Zones and Controlled Output....................................... 10
3.2 Enabling/Disabling Zones.................................................................... 10
3.3 Info on Status SMS.................................................................................. 11
3.4 Blocking Unknown Numbers.............................................................. 11
3.5 Remote Microphone Listening.......................................................... 12
3.6 Managing C1 and C2 Controlled Outputs. Timer........................ 12
3.7 SMS Message Delivery to Multiple Users...................................... 12
3.8 Calling all users....................................................................................... 13
3.9 Configuration for advanced users.................................................... 14
3.9.1 Additional possibilities of configuring
zones (inputs) alarm and restore........................................ 25
3.9.2 Additional possibilities of controlling and
configuring controller C1 (relay output)......................... 27
3.9.2.1 Settings of the output controlled by calls......... 27
3.9.2.2 Settings of the output controlled
by SMS messages...................................................... 28
3.9.2.3 Output control settings by event time............... 30
4.Appendix
4.1 Restoring Default Parameters. ........................................................... 32
4.2 „ELDES Configuration Tool“ software.............................................. 32
4.2 Technical Support................................................................................... 32
1. General Information
1.1 Function
ESIM252 is a micro controller based device intended to inform users about the alarm in automatic or security systems. In addition
it can control up to two electric appliances.
1.2 Operation Description
Description of factory default settings.
GSM control system ESIM252 operates over GSM network 24/7, i. e. it always reacts to the incoming signal.
In case any input is violated, the system sends an SMS message and/or calls to the preset user phone numbers. SMS message
with the name of the violated zone will continue to be sent until successful delivery to one of the users or until it is delivered to
all users. The system continues to call until one of the five users answers the call, rejects the call or until the call is ended by the
GSM service provider. If the user answers the call, the system activates microphone (must be connected to ESIM252) for listening
on what is happening in the secured premises. When using audio feature in case of input alarm or restore event the user will be
able to listen to particular sound record uploaded to the ESIM252 device memory. After the end of the sound record, the system
activates the microphone for listening on what is happening in the secured premises. After „hanging the phone“ or after the end
of the call (duration - 1 min.), the system will return to the previous state. Please, refer to ELDES Configuration Tool software Help
section for more details on audio feature.
Up to 2 electric appliances connected to ESIM252 can be controlled from a mobile phone. This feature allows to turn on/off heating, lighting, lift the gates, blinds etc.
The system ignores incoming calls from unknown phone numbers and SMS messages with wrong password.
List of other configurable system possibilities.
Input types
Ways of initiating an
event
Normally open (NO)
Operational only when the signal is switched.
Event when an input is
violated (Alarm)
Phone call initiated and/or SMS is delivered to user (-s) when the signal is
transmitted to an input.
Event when a zone is
restored (Restore)
Phone call initiated and/or SMS is delivered to user (-s) when the previously
transmitted input signal disappears.
Impulse counting
Input is considered as violated only if the number of the preset impulses in the
input is exceeded. Max. value is 4294967295 impulses.
SMS
Ways of notifying about
an event
Phone Call
Turning on/off by SMS
Ways of controlling
outputs (relays) Event log
4
Operational only when the signal is transmitted.
Normally closed (NC)
Turning on/off by a call
The ways of notifying users about events occurred in the particular input can be
carried out only SMS, only a phone call or a combination of both can be chosen.
Besides, any of the users can be assigned to be informed in case a particular
input is violated or restored or both. Various combinations of informing can be
assigned for each user and input.
When features SMS All and Call All are enabled, the system sends SMS messages
and rings to all preset users starting with User1 despite the fact that the call was
answered or rejected etc.
Examples: User NR1 wants to be informed by SMS in case input Z3 is violated,
but does not want to be informed when input Z3 is restored. User NR3 wants to
be informed by SMS and phone call in case input Z2 is violated, but wants to be
informed only by SMS in case of Z2 restore event.
The outputs can be turned on/off by sending the command by SMS message.
You can turn on/off:
1. for a permanent status
2. for a set period
3. for a set hour
4. repeating turning on/off.
The outputs can be turned on/off by calling. You can turn on/off:
1. for a permanent status
2. for a set period
3. toggle (output status changes after each call) Automatic turning on at
the preset hour
Outputs can be turned on for a set period at a set hour.
E. g. the relay is turned on at 18:00 and it is on for 5 hours. After 5 hours it turns
off automatically notifying the user about that.
Event log feature
List of occurred events by date and time - zone alarm/restore, output on/off etc.
1.3 Technical Specifications
Electrical and mechanical specifications
Supply voltage
10-24V 50Hz ~ 200mA max / 10-24V
200mA max
50mA max
850/900/1800/1900 MHz
4
1
Voltage: 0... 1.6V; current: -0.8... -0.4mA
Voltage: 5... 50V; current: 0.17.... 1.7mA
2
Relay. Normally open (NO)
24V
1A / 24V 50Hz ~0,5A
82x63x20mm
-20…+55oC
(-30...+55oC with limitations)
Current used in standby mode
GSM modem frequency
Number of “low” level (negative) inputs
Number of “high” level (positive) inputs
Allowable „low“ level (negative) input values
Allowable „high“ level (positive) input values Number of outputs
Output type
Relay output maximum commutating values
Dimensions
Operating temperature range
1.4 Connector Functionality
Short explanation of the main units
USB
SIM
CARD
ANT
GSM
MODEM
GSM MODEM
SIM CARD
LED
DEFAULT
ANT
LED1
LED2
MIC
DEFAULT D1 D2
F1
AC/DC RELAY1 RELAY2 COM Z5 Z4 Z3 Z2 Z1
Picture 1
USER MANUAL ELDES ESIM252 V1.0
USB
F1
GSM network 850/900/1800/1900 MHz
modem
SIM card
Light-emitting diodes indicator
Connectors (D1 and D2) for restoring
default settings
GSM antenna SMA type connector
Mini USB connector
Fuse
Connector functionality
Labeling
AC/DC
RELAY1
RELAY2
COM
Z5
Z4
Z3
Z2
Z1
Explanation
Power supply pins
Dry relay contact. Normally open (NO)
Dry relay contact. Normally open (NO)
Common pin
“Low” level input Z5
“Low“ level input Z4
“Low” level input Z3
“High” level input Z2
“Low” level input Z1
5
LED indicators functionality
LED1
LED2
Indicates SIM card status
Indicates network status
LED1 status
OFF
Meaning
SIM card is working properly
ON
SIM card error
LED2 status
OFF
Meaning
No network connection
Blinking 3 times per second
Poor network connection
Blinking 1 time per second
Medium network connection
ON
Excellent network connection
1.5 Connection Circuit
USEFUL INFORMATION
When choosing GSM provider, it is worth inquiring whether the service is used in security application assuring fast and reliable
SMS message delivery and phone call connection.
USEFUL INFORMATION
When choosing GSM cellular provider, it is worth inquiring whether the service is used in security application assuring fast and
reliable SMS message delivery and phone call connection.
Esim252 and alarm system COM must be connected.
Inputs Z1, Z3, Z4, Z5 are connected to alarm system outputs if outputs are implemented as open collector circuit or any other
circuit and if it commutes with COM.
It is also possible to connect Z1, Z3, Z4, Z5 inputs to, for instance, motion sensor or any other sensor as well as automatics device
provided the inputs are commuted with COM.
Input Z2 is commuted with a “high level” impulse. Impulse duration is >600ms.
GSM Control System
ESIM252
AC/DC
RELAY1
RELAY2
COM Z5 Z4
Z3
Z2
AC/DC
Metal box
PE contact
Z1
Fuse 500 mA
~10-24V
Picture3 AC power supply connection circuit
PGM1
PGM2
PGM3
PGM4
PGM5
AUX- AUX+
HIGH
LEVEL
Alarm system or other appliance
Picture 2
6
~230V 50Hz
1.6 System Installation
The system can be installed only in a metal or non-flammable plastic enclosure. If the metal enclosure and transformer is used it
is necessary to ground the enclosure using yellow/green colour cable. For the connection of 230V transformer use 3x0.75 mm2
1 thread double isolated cable. The primary circuit of the transformer must be connected through 0.5A fuse. 230V power supply
cables cannot be grouped with low voltage cable group. For the connection of power supply and output connectors use 1 thread
2x0.75 mm2 cable. For the connection of input/output connectors use 0.50 mm2 1 thread cable.
1. Fasten the system in the box using fastening holders.
2. Place SIM card in the holder but make sure that SIM card PIN code is disabled. (PIN code can be disabled by putting SIM card
into mobile phone and following proper menus). SIM card should not have any remaining SMS messages.
3. Connect the circuit as shown in fig. No 2. Power supply cables are connected last). When connecting Esim252 to alarm system
power supply, usually the security system AUX output is used.
4. When AC power supply (ground transformer) is used connect according to circuit no. 3. In this case you do not need to connect any other power supplies.
5. The system will start in less than a minute. LED2 indicator should be blinking or be ON indicating connection to GSM.
USER MANUAL ELDES ESIM252 V1.0
7
2. System Pre-operation and
the Main Control Commands
VERY IMPORTANT!!!
Underscore symbol ‘_’ in this manual is used to represent space. When writing SMS messages, every underscore symbol should be
replaced by single space symbol. XXXX – means password. Do not leave any space at the beginning and the end of the message.
To set ESIM252 system parameters easier and quicker you can use the computer, USB cable or remote device configuration over
GPRS connection and configuration software „ELDES Configuration Tool“. For more details, please, refer to chapter 3.2.
2.1 Selecting device language and verification of SMS central number
The language in which the device communicates with the user can be chosen before changing factory default password. To change
the language in the system that is already configured reset default settings as described in 3.1 appendix.
Send SMS message with the required language
code to the number of the SIM card inserted in
Esim252.
E.g., if you want to set the English language send
the following SMS message: EN
Table of
possible
languages
Language
Code
lithuanian
LT
english
EN
ESIM 252
30-60 seconds later you should get an SMS message:
russian
RU
„English language confirmed.“ Go to chapter 2.2 upon
reception of this message.
Otherwise check for network connection and call Esim252 system from your mobile and wait until the system drops the call. You
should get an SMS message asking to change default password. Otherwise check for network connection and change SMS central
number.
SMS central number is saved in SIM card, therefore if SIM card has been used to send SMS messages with a mobile phone,
then you don’t’ need to change SMS central number. Often SMS central number is already saved in SIM card by cellular
operator.
Central number can be entered by sending SMS message:
XXXX_SMS_+37011111111
XXXX – is a password. Default password is four zeros: 0000. SMS central number is provided by cellular network provider.
Example: 0000_SMS_+37069899992
Message should be sent to the number of SIM card which is placed into the system. If all went correct, the system will send a message: SMS central number has been successfully changed to +37011111111
2.2 Password Change
All SMS commands start with a password, please memorize it. Manufacturer default password is
four zeros 0000, which is necessary to change.
ESIM 252
0000_
PSW_XXXX
Manufacturer default password can be changed by sending the following SMS message to
Esim252:
0000_PSW_XXXX
To replace your password, send the following SMS message:
YYYY_PSW_XXXX
XXXX is any four digit number except four zeros.
Non-numerical characters like dots, colons, spaces are not allowed. YYYY is the old system password. If you forgot the password,
default manufacturer password can be restored, see chapter 4.1 for more details.
8
2.3 User Numbers
The system Esim252 allows to pre-program up to five different mobile numbers which will have access to and control the system.
NR1 is mandatory while others can be skipped. All numbers must be entered starting with international country code, e. g. national
code for Lithuania is 370, UK – 44. By default the system starts sending all messages and in the event of alarm starts calling on the
first number, and if the first call is unsuccessful, it immediately tries reaching subscriber No2 etc.
2.3.1 Saving or Changing Numbers
Send SMS message with the following text to Esim252:
XXXX_NR1:37011111111_NR2:37011111111_NR3:37011111111_NR4:37011111111_
NR5:37011111111
ESIM 252
XXXX_
NR1:370
11111111_
NR4:370
11111111
ESIM 252
XXXX_
NR3:370
11111111
Ones should be replaced with user numbers.
Numbers don’t have to be entered in sequential order right away. E. g. user can enter first and
fourth number by sending the following SMS message:
XXXX_NR1:37011111111_NR4:37011111111
Or individually one number at a time:
XXXX_NR3:37011111111
Numbers can be changed same way as described above. New number will overwrite old one, therefore no erasing is necessary.
2.3.2 Verification of Saved Numbers
To inquire the system about pre-programmed numbers, send the following SMS message:
ESIM 252
XXXX_
HELPNR
ESIM 252
XXXX_
NR3:DEL
ESIM 252
XXXX_
2009.01.
01_14:15
XXXX_HELPNR
The system will reply with all pre-programmed numbers.
2.3.3 Deletion of Saved Numbers
To erase NR2-NR5, send the following SMS message:
XXXX_NR2:DEL_NR3:DEL_NR4:DEL_NR5:DEL
E. g. XXXX_NR3:DEL
The system will not allow erasing first number NR1. It can only be modified.
2.4 Date and Time Settings
It is important to set correct date and time so that the system can send reports at specified times.
Date and time can be set by sending the following format SMS message:
XXXX_MMMM.mn.dd_va:mi
where MMMM means year; mn - month; dd - day; va - hour; mi - minutes
E. g. XXXX_2009.01.01_14:15
USER MANUAL ELDES ESIM252 V1.0
9
3. Additional System Capabilities
3.1 Renaming Input Alarm/Restore Texts & Оutput Нames
Manufacturer initially set the following input alarm/restore texts and output names:
input Z1 alarm text - Zone1 Alarm, restore text - Restore1; input Z2 - Zone2 Alarm, restore text - Restore2; 0 input Z3 - Zone3 Alarm,
restore text - Restore3; input Z4 - Zone4 Alarm, restore text - Restore4; input Z5 - Zone5 Alarm, restore text - Restore5; output C1
name - Controller1; output C2 name - Controller2
E. g. in case input Z1 is violated, the system sends SMS message with the text: Zone1
Input alarm text
Input alarm text is changed by sending the following SMS mesaage:
XXXX_Z1:NewAlarmText;Z2:NewAlarmText;Z3:NewAlarmText;Z4:NewAlarmText;Z5:NewAlarmText;
E. G. XXXX_Z1:Intrusion though the door;Z2:Fire sensor alarm;
Texts can be changed all at once for all inputs, several of them or one by one. Maximum text for one
input text is 24 characters. The space is equal to one character. Each new text must be followed by a semi
colon. As semi colon is used for separating texts for different inputs. It cannot be used in the middle of
alarm texts, it can only be used at the end. Texts cannot be the same as configuration and control commands, such as - ON, OFF, STATUS etc.
ESIM 252
XXXX_Z1:
trespaced;
Z2:
triggered
fire
detector;
Input restore text
If you want to be notified by an SMS message when a violated zone is restored Restore mode must be turned on. The mode is turned
on by sending a particular SMS command. Please refer to chapter 3.9 or configuration program.
Input restore text is changed by sending the following SMS mesaage:
XXXX_ZR1:NewRestoreText;ZR2:NewRestoreText;ZR3:NewRestoreText;ZR4:NewRestoreT
ext;ZR5:NewRestoreText;
Output name can be changed by sending the following SMS message:
XXXX_Cx:NewControllerName
x - output number; possible values 1 - C1 or 2 - C2.
Output name cannot be followed by a semi colon. You cannot change input alarm/restore text and output names at the same time.
E. g. XXXX_C1:PUMP
3.2 Enabling/Disabling Inputs
NOTE
Manufacturer set all the inputs activated, i. e. in mode ON.
USEFUL INFORMATION
The inputs can be enabled/disabled together or separately one by one.
Enabling Input
Any input can be enabled by sending the following SMS message:
XXXX_Z1:ON;Z2:ON;Z3:ON;Z4:ON;Z5:ON;
10
ESIM 252
XXXX_C1:
PUMP
Disabling Input
Any input can be disabled by sending the following SMS message:
XXXX_Z1:OFF;Z2:OFF;Z3:OFF;Z4:OFF;Z5:OFF;
ESIM 252
XXXX_
WINDOWS:
OFF;
E. g. XXXX_Z2:ON; or XXXX_WINDOWS:ON; or XXXX_Z2:OFF; or XXXX_WINDOWS:OFF;
3.3 Info on Status SMS
The system ESIM252 can any time be inquired about signal strength and the status of inputs at the time when SMS message is sent.
At the same time system test is performed. If the answer to the request has been received, it means the system finely operates.
It is also useful for those using prepayment service – you can check if the credit in the account is sufficient for sending an SMS
message. Send the following SMS message:
XXXX_INFO
The reply SMS will have following info: e. g. 2008.08.07 11:15
Signal strength satisfactory. Z1:OK/ALARM Z2:OK/ALARM Z3:OK/ALARM Z4:OK/ALARM Z5:OK/ALARM
where OK means that there is no alarm in a particual input (restored). ALARM – the particular input is violated.
By default, this status SMS message will be sent daily at 11:00 in the morning. These parameters can
be configured by sending the following SMS message:
ESIM 252
XXXX_
INFO:01.
10
XXXX_INFO:PP.VV
PP – message period in days, valid values [00-10].
VV - time when message is sent, valid values [00-23].
E. g. XXXX_INFO:01.10 means that status message will be sent every 1 day at 10:00.
ESIM 252
XXXX_
INFO:0.2
If PP value is 0, and VV in the range of [1-23], then periodic status messages will be sent multiple times
per day, with period being specified as VV time.
E. g. XXXX_INFO:0.2 means that status message will be sent every 2 hours.
To disable periodic status messages send the following SMS message:
XXXX_INFO:00.00
The status messages will not be sent until enabling or restoring default parameters or receiving previously described XXXX_
INFO:PP.VV SMS message.
3.4 Blocking Unknown Numbers
By default Esim252 system can be controlled from any of the preset users NR1 - NR5. However, the user can access the system and
control parameters and outputs from any number as long as password is known.
To enable this feature send the following SMS message:
XXXX_STR:ON
To disable this feature send the following SMS message:
XXXX_STR:OFF
USER MANUAL ELDES ESIM252 V1.0
11
3.5 Remote Microphone Listening
NOTE
To enable this feature it is necessary to connect microphone connector to MIC slot. The microphone is additional equipment
tha can be purchased in trading centers.
You can listen to what is going on in the secured premises by sending the following SMS message:
XXXX_MIC
The system will ring the sender of the received SMS, and upon answering the call, the user can listen to any sounds in the building.
The phone call must be answered within 20 seconds otherwise the system will stop trying and return to previous state.
3.6 Managing C1 & C2 Outputs. Timer.
GSM control system ESIM252 contains two outputs C1 and C2. It can be used to control various electric appliance, such as electric
pumps, heating, lighting etc. When the output (-s) is turned on, the relay connectors of the output are in NC state (normally closed).().
The output is turned on by sending the following SMS message:
XXXX_Cx:ON
x - output number; possible values 1 - C1 or 2 - C2.
The output is turned off by sending the following SMS message:
ESIM 252
XXXX_
PUMP:
ON
XXXX_Cx:OFF
x - output number; possible values 1 - C1 or 2 - C2. Instead of C1 or C2 it is also possible to use real output name.
E.g.. XXXX_PUMP:ON
Timer
GSM control system ESIM252 has internal timer. This feature allows any output to be turned on or off for a specified time period.
The following SMS command should be sent:
XXXX_Cx:ON/OFF:vv.mm.ss
x - output number; possible values 1 - C1 or 2 - C2. ON – output enabled. OFF – disabled
vv – hours, valid values [00-23] mm – minutes, valid values [00-59] ss - seconds, valid values [00-59]
It is not allowed to have all values equal zeros. Zeros it is not allowed to have all values equal
E. g. to switch the pump on for 01 minutes and 23 seconds, send SMS XXXX_PUMP:ON:00.01.23
ESIM 252
XXXX_
PUMP:
OFF:00.
01.23
If the pump was enabled before and user want to disable it for 01 minute and 23 seconds, send SMS
XXXX_PUMP:OFF:00.01.23
If you want to use more capabilities of the outputs, such as TOGGLE, automatic output control at a
particu­lar, use configuration software „ELDES Configuration Tool“ or refer to chapter 3.9.2
3.7 SMS Message Delivery to Multiple Users
Upon activated alarm in security system, ESIM252 SMS messages are repeatedly sent until first successful delivery to one of the
users. The system starts with NR1 and if delivery fails, it follows with NR2 etc.
It is also possible to set the system so that it sends SMS message to all preset users in the system.
12
To enable this function send the following SMS message:
XXXX_SMSALL:ON
To disable this function send the following SMS message:
XXXX_SMSALL:OFF
If you want to configure SMS message delivery only for particular users or only for particular inputs, please, refer to chapter 3.9 or
use configuration program ELDES Configuration Tool.
3.8 Calling all users
During the alarm, Esim252 system starts calling NR1. If the call to NR1 was unsuccessful or the subscriber was out of network coverage the call is forwarded to NR2 etc. If the user rejected the call or answered te call during the alarm the system stops calling.
However, you can set the system to call all users entered in the system regardless of the fact whether the user answered or rejected
the call, was out of network coverage or was engaged.
To turn on this feature send the following SMS message:
XXXX_CALLALL:ON
ATTENTION!
When this feature is enabled it will not be possible to stop calling the next user in the sequence even if the call is answered. To disable this function send the following SMS message:
XXXX_CALLALL:OFF
If you want to configure calling only to particular users or only for particular zones, refer to chapter 3.9 or use configuration program
ELDES Configuration Tool.
3.9 Configuration for advanced users
All features described in chapter 3.9 of the user manual can be configured using “ELDES Configuration Tool“ software. In
case if there is no possibility of connecting the device to the computer via USB or if you want to change the settings remotely you
can do this via remote configuration feature over GPRS using “ELDES Configuration Tool“ or via SMS messages. We recommend
changing the settings by SMS only for advanced users.
USER MANUAL ELDES ESIM252 V1.0
13
F O R A D VA N C E D U S E R S
All these features can be configured using program “ELDES Configuration Tool“
E. g. 1
The user wants to connect Esim252 system to an existing alarm in a building where enterprise A and and enterprise B work. Both
enterprises use the same alarm system that has two inputs. The alarm system has 5 outputs PGM.
Task NO1:
Configuring the system so that the director of a particular enterprise is informed about security arming depending on which enterprise employee armed the alarm system. The director of enterprise A (NO1) wants to receive an SMS message only and does not
want to receive any calls, the director of enterprise B (NO2) wants to receive a call and does not want to receive any SMS messages.
PIR
PIR
Enterprise A
Director A
NO1
Enterprise B
Director B
NO2
Alarm system
PGM1
PGM2
Alarm
SMS
ESIM151
Alarm
Calls
Worker A
NO4
Worker B
NO5
Janitor
GATES
Janitor
NO3
As per factory default settings SMS message sending feature in the case of alarm is enabled for all users until the first successful
delivery of the SMS message, it is necessary to remove the users that should not receive any alarm messages. Besides, as per factory
default settings, calling feature in the case of alarm is also enabled for all users therefore call function must be disabled for all users
except user NO2.
a) First of all alarm system unit must be programmed in the way so that when security is armed in office A, output PGM1 is
turned on, and when security is armed in office B, output PGM2 is turned on.
b) Output PGM1 is connected to ESIM252 input Z1, and output PGM2 is connected to ESIM252 input Z2. (output PGM2 type
should be “high level”).
c) The following two configuration SMS messages must be sent to Esim252 system:
XXXX_SMSEXTRA:Z1:SC2345,CC12345
where SC2345 means that alarm SMS message sending to users NO2-NO5 is disabled after input Z1 is violated. CC12345 means that
alarm calls are disabled for all users NO1-NO5 after input Z1 is violated.
XXXX_SMSEXTRA:Z2:SC12345,CC1345
14
where SC12345 means that alarm SMS message sending is disabled for all users NO1-NO5 after input Z2 is violated. CC1345 means
that all alarm calls are disabled for users NO1, NO3-NO5 after input Z2 is violated.
F O R A D VA N C E D U S E R S
All these features can be configured using program “ELDES Configuration Tool“
Task NO2:
Configuring the system so that the janitor (NO3) is notified by by SMS messa­ge and call about the violated PIR movement sensor‘s
input in the secured area; and when the sensor‘s input is restored, the janitor receives SMS message only.
PIR
PIR
Enterprise A
Director A
NO1
Enterprise B
Director B
NO2
Alarm system
PGM3
Worker A
NO4
ESIM151
Worker B
NO5
Janitor
GATES
Alarm
SMS/Calls
Restore
SMS
Janitor
NO3
As per factory default settings SMS message sending feature in the case of alarm is enabled for all users until the first successful
delivery of the SMS message, it is necessary to remove the users that should not receive any alarm messages. Besides, as per factory
default settings, calling feature in the case of alarm is also enabled for all users therefore call function must be disabled for all users
except user NO3. SMS message sending feature must also be enabled for user NO3 when input Z3 is restored.
a) First of all alarm system unit must be programmed in the way so that when PIR movement sensor‘s input is violated, output
PGM3 is activated.
b) Output PGM3 is connected to ESIM252 input Z3.
c) The following configuration SMS message must be sent to Esim252 system:
XXXX_SMSEXTRA:Z3:SC1245,CC1245,SE3
where SC1245 means that alarm SMS message sending to users NO1, NO2, NO4 and NO5 is disabled after input Z3 is violated.
CC1245 means that alarm call feature is disabled for users NO1, NO2, NO4 and NO5 after input Z3 I is violated. SE3 means that SMS
message sending feature is enabled for user NO3 after Z3 input is restored.
USER MANUAL ELDES ESIM252 V1.0
15
F O R A D VA N C E D U S E R S
All these features can be configured using program “ELDES Configuration Tool“
E. g. 1
The user wants to connect ESIM252 system to an existing alarm system in a building where enterprise A and enterprise B work.
Both enterprises use the same alarm system unit that has 2 inputs and 5 outputs PGM.
Task NO3:
Configuring the system so that the intrusion to enterprise A premises is reported to the janitor (NO3) and enterprise A employee
(NO4) by SMS messages and calls. Enterprise A employee (NO4) wants to receive a call only in the case if the janitor (NO3) does not
answer the call, is out of network coverage or at that time the janitor’s telephone line is engaged.
PIR
PIR
Enterprise A
Director A
NO1
Enterprise B
Director B
NO2
Alarm system
PGM4
Worker A
NO4
ESIM151
Alarm
SMS/Calls
Worker B
NO5
Janitor
GATES
Alarm
SMS/Calls
Janitor
NO3
As per factory default settings SMS message sending feature in the case of alarm is enabled for all users until the first successful
delivery of the SMS message, it is necessary to enable mandatory SMS message delivery (see more in chapter 3.7) and to remove
the users who should not receive alarm messages. Besides, as per factory default settings, calling feature in the case of alarm is also
enabled for all users therefore call function must be disabled for all users except users NO3 and NO4. As per factory default settings
in the case of alarm the system rings until the first answered call, therefore in this case nothing should be configured.
a) First of all alarm system unit must be programmed in the way so that when security sensors of enterprise A are violated, the
signal is transmitted to alarm system unit‘s output PGM4.
b) Output PGM4 is connected to ESIM252 input Z4
c) The following configuration SMS messages must be sent to Esim252 system:
XXXX_SMSALL:ON
where SMSALL enables mandatory SMS message delivery feature for all users.
XXXX_SMSEXTRA:Z4:SC125,CC125
Where SC125 means that alarm SMS message delivery feature is disabled for users NO1, NO2 and NO5 after input Z4 is violated.
CC125 means that alarm calls are disabled for users NO1, NO2 and NO5 after input Z4 is violated.
16
F O R A D VA N C E D U S E R S
All these features can be configured using program “ELDES Configuration Tool“
Task NO4:
Configuring the system so that the intrusion to enterprise B premises is reported to the janitor (NO3) and enterprise B employee
(NO5) by SMS messages and calls, and the director of enterprise B (NO2) receives SMS message only. Enterprise B employee (NO5)
must receive the phone call even in the case when the janitor (NR3) answers the call.
PIR
PIR
Enterprise A
Director A
NO1
Enterprise B
Director B
NO2
Alarm system
PGM5
Alarm
SMS
ESIM151
Alarm
SMS/Calls
Worker A
NO4
Worker B
NO5
Janitor
GATES
Alarm
SMS/Calls
Janitor
NO3
As per factory default settings SMS message sending feature in the case of alarm is enabled for all users until the first successful
delivery of the SMS message, it is necessary to enable mandatory SMS message delivery (see more in chapter 3.7) and to remove
the users who should not receive alarm messages. Besides, as per factory default settings, calling feature in the case of alarm is also
enabled for all users therefore call function must be disabled for users NO1, NO2 and NO4, and left enabled for users NO3 and NO5.
Also, it is necessary to enable mandatory calling feature for all preset users (see more in chapter 3.8).
a) First of all alarm system unit must be programmed in the way so that when security sensors are violated the signal must be
transmitted to alarm system unit‘s output PGM5.
b) Output PGM5 is connected to ESIM252 input Z5
c) The following three configuration SMS messages must be sent to Esim252 system:
XXXX_SMSALL:ON
where SMSALL enables mandatory SMS message delivery feature for all users.
XXXX_CALLALL:ON
where CALLALL enables mandatory calling feature for all users.
XXXX_SMSEXTRA:Z5:SC14,CC124
where SC14 means that alarm SMS message sending feature is disabled for users NO1 and NO4 after input Z5 is violated. CC124
means that alarm calls are disabled for users NO1, NO2 and NO4 after input Z5 is violated.
USER MANUAL ELDES ESIM252 V1.0
17
F O R A D VA N C E D U S E R S
All these features can be configured using program “ELDES Configuration Tool“
E. g. 2.
The user wants to connect ESIM252 system to the outputs PGM of an existing alarm system. House area is entered through
automatically controlled gates. There are 5 users in total. NO1 is the housekeeper, NO2 is a neighbour, NO3-NO5 are family
members.
Task NO1:
Configuring the system so that house alarm activation is reported to the housekeeper (NO1) by SMS message and a call as well as
to the neighbour (NO2) but by SMS message only.
PIR
PIR
Housekeeper
NO1
Alarm
SMS/Calls
Neighbour
NO2
Alarm
SMS
Alarm system
Family members:
PGM
ESIM151
PIR
PIR
NO3
NO4
NO5
GATES
As per factory default settings SMS message sending feature in the case of alarm is enabled for all users until the first successful
delivery of the SMS message, it is necessary to enable mandatory SMS message delivery (see more in chapter 3.7) and to remove
the users who should not receive alarm messages. Besides, as per factory default settings, calling feature in the case of alarm is also
enabled for all users therefore call function must be disabled for users NO2-NO5 and left enabled for NO1 only.
a) First of all alarm system unit must be programmed in the way so that when security sensors are violated the signal must be
transmitted to alarm system system unit output PGM.
b) Output PGM is connected to ESIM252 input Z1
c) The following two configuration SMS messages must be sent to Esim252 system:
XXXX_SMSALL:ON
where SMSALL enables mandatory SMS message delivery for all users.
XXXX_SMSEXTRA:Z1:SC345,CC2345
Where SC345 means that alarm SMS message sending is disabled for users NO3, NO4 and NO5 after input Z1 is violated.
CC2345 means that alarm calls are disabled for all users except NO1 after input Z1 zone is violated.
18
F O R A D VA N C E D U S E R S
All these features can be configured using program “ELDES Configuration Tool“
Task NO2:
Configuring the system so that house gates could be opened via free calls by the housekeeper (NO1) and his family members
(NO3), (NO4) and (NO5). After every successful gate opening the user NO5 wants to receive a confirmation call (Call Back) the
duration of which is 3 seconds, and the user NO3 wants to receive a confirmation SMS message.
Control
Call
Confirmation
SMS
Gate controller
ESIM151
Housekeeper
NO1
Family member
NO3
Family member
NO4
Confirmation
Call
3 sek.
Family member
NO5
GATES
As per factory default settings C1 output control via calls is disabled for all users, it is necessary to enable this feature and to set the
users who will be able to control the output. Besides, it is also necessary to set output status for every user when he/she makes a call
to the system. In this case the output must be turned on and the duration must be 1 second; afterwards the output returns to the
previous state. Call Back feature must be enabled for user NO5 and it is necessary to choose the length parameters for that call. Also,
confirmation SMS messages have to be enabled for user NO3.
a) First of all Esim252 system relay output has to be connected to the connectors of gate control unit.
b) The following configuration SMS message must be sent to Esim252 system:
XXXX_SMSEXTRA:COC1:CE1345,CS5,CT513,SS3,MS10,MS30,MS40,MS50,MS1T0.0.1,MS3T0.0.1,MS4T0.0.1,MS5T0.0.1
where COC1 means C1 output control by call is enabled for users NO1, NO3-NO5.
CS5 means that Call Back feature is enabled for user NO5 after output C1 status changes.
CT513 means that user NO5 will receive a confirmation call when the output gets activated and call duration is 3 seconds.
SS3 means that user NO3 will be informed about output C1 status change by SMS message.
MS10 means that the output is activated when user NO1 calls the system.
MS30 means that the output is activated when user NO3 calls the system.
MS40 means that the output is activated when user NO4 calls the system.
MS50 means that the output is activated when user NO5 calls the system.
MS1T0.0.1 means that output status is changed for 1 second when user NO1 calls the system.
MS3T0.0.1 means that output status is changed for 1 second when user NO3 calls the system.
MS4T0.0.1 means that output status is changed for 1 second when user NO4 calls the system.
MS5T0.0.1 means that output status is changed for 1 second when user NO5 calls the system.
USER MANUAL ELDES ESIM252 V1.0
19
F O R A D VA N C E D U S E R S
All these features can be configured using program “ELDES Configuration Tool“
E. g. 3.
The user wants to connect Esim252 system to the heating system of the house.
Task No1:
Configuring the system so that house heating system is turned on and turned off by the user (NO1) via free call. This user should
also receive free information about successful turning on or turning off of the heating system.
Flood detector
User
NO1
Heating
Controller
User
NO2
ESIM151
Confirmation
Call
3sek/10sek
Control
Call
As per factory default settings C1 output control via calls is disabled for all users, it is necessary to enable this feature and to set the
users who will be able to control the output – in this case it is user NO1. Besides it is also necessary to set output status for user NO1
when he/she calls the system. In this case you must set the system so that the output is turned on after one call and turned off after
another one (Toggle) and so on. User NO1 needs to enable confirmation call (Call Back) feature and set the length parameters for
that call. To differentiate whether the output was turned on confirmation call will be set to ring for 3 seconds and the confirmation
call will ring for 10 seconds when the output was turned off.
a) First of all ESIM252 system output C1 has to be connected to the connectors of heating controller unit.
b) The following configuration SMS message must be sent to Esim252 system:
XXXX_SMSEXTRA:COC1:CE1,CS1,CT113,CT1010,MS12
where COC1 means C1 output control by call is enabled for users NO1.
CS1 means that confirmation call feature is enabled for user NO1 after output C1 status changes.
CT113 means that user NO1 will receive a confirmation call when the output is turned on and call duration is 3 seconds.
CT1010 means that user NO1 will receive a confirmation call when the output is turned off and call duration is 10 seconds.
MS12 means that Toggle mode is activated for user NO1 which means that output status is changed with every call.
20
F O R A D VA N C E D U S E R S
All these features can be configured using program “ELDES Configuration Tool“
Task No2:
Configuring the system so that users (NO1) and (NO2) receive SMS message about a burst water pipe (flood) at home. SMS messages must be delivered to both users.
Flood detector
User
NO1
Heating
Controller
User
NO2
Alarm
SMS
ESIM151
Alarm
SMS
As per factory default settings SMS message sending feature in the case of alarm is enabled for all users until the first successful
delivery of the SMS message and calling in the case of alarm is enabled for all users until the first answered call, calling feature in the
case of alarm must be disabled for users NO1 and NO2. Mandatory SMS delivery to all users must also be enabled.
a) First of all a flood sensor is connected to Esim252 input Z1.
b) The following configuration SMS messages must be sent to Esim252 system:
XXXX_SMSALL:ON
where SMSALL enables mandatory SMS message delivery feature for all users.
XXXX_SMSEXTRA:Z1:CC12
where CC12 means that alarm call feature is disabled for users NO1, NO2 after input Z1 violation.
We make an assumption that users NO3-NO5 were not preset in the system at all.
USER MANUAL ELDES ESIM252 V1.0
21
F O R A D VA N C E D U S E R S
All these features can be configured using program “ELDES Configuration Tool“
E. g. 4.
The company taking care of automatic systems needs to have information about critical breakdowns of mechanisms and has to
quickly react and eliminate the breakdown. There are three members of operating personnel (NO1), (NO2) and (NO3).
Task No1:
Configuring the system so that operating personnel member (NO1) receives SMS message about the breakdown of gas boiler.
Working normally a gas boiler transfers a signal, and when it breaks down the signal is not transmitted.
Pump
Worker
NO1
Gas boiler
Fault
signal
ESIM151
Alarm
SMS
Automatic
system
Worker
NO2
Worker
NO3
As per factory default settings SMS message sending feature in the case of alarm is enabled for all users until the first successful
delivery of the SMS message, it is necessary to remove users NO2 and NO3 and disable alarm calls for all users. It is also necessary to
invert Esim252 input from NO to NC mode so that alarm is given only when the signal disappears.
a) First of all a signal indicating gas boiler breakdown isconnected to Esim252 input Z1.
b) The following configuration SMS message must be sent to Esim252 system:
XXXX_SMSEXTRA:Z1:SC23,CC123,LI1
22
where SC23 means that alarm SMS message sending is disabled for users NO2, NO3 input Z1 is violated.
CC123 means that alarm calls are disabled for users NO1, NO2 and NO3 after input Z1 is violated.
We make an assumption that users NO4-NO5 were not entered to the system at all. LI1 means that NC “normally closed” - mode is enabled for the input.
F O R A D VA N C E D U S E R S
All these features can be configured using program “ELDES Configuration Tool“
Task No2:
Configuring the system so that the operating personnel member (NO2) receives SMS message if the pump‘s input was violated for
10 times.
Pump
Worker
NO1
Gas boiler
ESIM151
Alarm
SMS
Automatic
system
Worker
NO2
Worker
NO3
As per factory default settings SMS message sending feature in the case of alarm is enabled for all users until the first successful
delivery of the SMS message, it is necessary to remove users NO1 and NO3 and disable alarm calls for all users. It is also necessary to
enable impulse counting mode for Esim252 input Z3 and set the number of expected impulses.
a) First of all a signal indicating PUMP triggering is connected to Esim252 input Z3.
b) The following configuration SMS message must be sent to Esim252 system:
XXXX_SMSEXTRA:Z3:SC13,CC123,IE1,IC10
where SC13 means that alarm SMS message sending is disabled for users NO1, NO3 after input Z3 zone violation.
CC123 means that alarm calls are disabled for users NO1, NO2 and NO3 after input Z3 violation.
We make an assumption that users NO4-NO5 were not entered to the system at all.
IE1 enables impulse counting mode for input Z3. IC10 means that the alarm is given to input Z3 after 10 impulses are transmitted.
USER MANUAL ELDES ESIM252 V1.0
23
F O R A D VA N C E D U S E R S
All these features can be configured using program “ELDES Configuration Tool“
E. g. 4.
The company taking care of automatic systems needs to have information about critical breakdowns of mechanisms and has to
quickly react and eliminate the breakdown. There are three members of operating personnel (NO1), (NO2) and (NO3).
Task No3:
Configuring the system so that operating personnel members (NO1), (NO2) and (NO3) can reboot the “hanged” automatic control
system without going to the object but via a short call to Esim252 system.
Pump
Worker
NO1
Gas boiler
ESIM151
Control
Calls
Automatic
system
Worker
NO2
Worker
NO3
As per factory default settings C1 output control via calls is disabled for all users, it is necessary to enable this feature and to set the
users who will be able to control the output. Besides, it is also necessary to set output status for every user when he/she makes a
call to the system. In this case the output must be turned on and the duration must be 2 seconds; afterwards the output returns to
the previous state.
a) First of all ESIM252 system output has to be connected to automatic system unit.
b) The following configuration SMS message must be sent to Esim252 system:
XXXX_SMSEXTRA:COC1:CE123,MS10,MS20,MS30,MS1T0.0.2,MS2T0.0.2,MS3T0.0.2
MS10 means that the output is activated when user NO1 calls the system.
MS20 means that the output is activated when user NO2 calls the system.
MS30 means that the output is activated when user NO3 calls the system.
MS1T0.0.2 means that output status is changed for 2 seconds when user NO1 calls the system.
MS2T0.0.2 means that output status is changed for 2 seconds when user NO2 calls the system.
MS3T0.0.2 means that output status is changed for 2 seconds when user NO3 calls the system.
24
F O R A D VA N C E D U S E R S
All these features can be configured using program “ELDES Configuration Tool“
3.9.1 Additional possibilities of configuring input alarm and restore
During the alarm the system calls and sends SMS messages to all preset users until the first successful SMS delivery or a call rejected
by the user. The users are not notified about input restore. Input delay due to interference is 600ms – i. e. only the impulse that is
longer than 600ms is considered an event. All inputs Z1 - Z5 are enabled. Impulse counting mode is turned off.
To change these settings send the following SMS message:
XXXX_SMSEXTRA:Zn:Value1,Value2,……,ValueN
XXXX – user password.
Zn – possible values Z1,Z2,Z3,Z4,Z5. Define the number of the input that is changed.
Value structure is CnVal, where Cn means command name (2 letters), and Val-its value (digits without spaces or punctuation marks). Value (CnVal) – Table of values
Cn – command
name (2 letters)
Val – possible
command
meaning.
SS
1,2,3,4,5
SC
1,2,3,4,5
CS
1,2,3,4,5
CC
1,2,3,4,5
SE
1,2,3,4,5
SD
1,2,3,4,5
CE
1,2,3,4,5
Alarm
configuration
Restore
configuration
CD
Input levels
1,2,3,4,5
During the alarm SMS
message will be sent to
users NO:1,2,3,4,5.
During the alarm SMS
message sending to
users No:1,2,3,4,5 will be
disabled.
During the alarm the
system will call users
No:1,2,3,4,5.
During the alarm calling
users No:1,2,3,4,5 will be
disabled.
During input restore SMS
message will be sent to
users No:1,2,3,4,5.
During input restore
SMS message sending is
disabled for No:1,2,3,4,5.
During input restore users
No:1,2,3,4,5 will be called.
During input restore
calling users No:1,2,3,4,5
is disabled.
0
Setting input type.
0 – NO (normally open).
1
Setting input type.
1 –NC (normally closed)
Initial factory
default values
Comments
SS12345
Enabled for all
users NO1-NO5.
E. g. SS25 means that during alarm SMS
message sending is enabled for users NO2
and NO5
E. g. SC2 means that SMS message sending
will be disabled for user NO2
CS12345 Enabled
for all users
NO1-NO5.
Impulse counting mode
is disabled
IE
0
IE
1
Impulse counting mode
is enabled
IC
1- 4294967295
The number of impulses is
determined
DV
100-10000
Setting minimal input
impulse duration. It is
measured in milliseconds.
USER MANUAL ELDES ESIM252 V1.0
E. g. CS124 means that during alarm calls are
enabled for users NO1, NO2 and NO4
E. g. CC12345 means that during the alarm
none of the users will be called.
E. g. SE1 means that during input restore
SMS message delivery is enabled for user
NR1
SD12345
Disabled for all
users NO1-NO5.
E. g. SD45 means that during input restore
SMS message sending is disabled for users
NO4 and NO5.
LI0 Normally open
E. g. CE12 means that during input restore
calls are enabled for users NO1 and NO2
E. g. CD1345 means that when the input is
restored users NO1, NO3, NO4 and NO5 will
not be called.
Possibility to change input type, i. e. to
invert. E. g. LI0
It means that the input is considered
inactivated if there is no signal.
Possibility to change input type, i. e. to
invert.
E. g. LI1 means that input is in normal status
when the signal is transmitted. The event
appears only when the signal disappears.
IE0 disabled
Pvz. IE0 means impulse counting mode is
disabled
CD12345
Disabled for all
users NO1-NO5.
LI
Impulse counting
Input protection
against
interference
Command description
DV600
Input counts impulses. The number of
impulses is defined by the command IC.
E. g. IE1
The alarm is activated when a preset
number of impulses is transmitted to the
input. E. g. IC100
In this case the alarm is activated when 100
impulses are sent to the input.
Maximum frequency is 5Hz.
The input is violated only if the impulse
transmitted is not shorter than the preset
value. E. g. DV1000 means that the signal
transmitted to the input is shorter than
1000ms (1s) the alarm is activated.
25
F O R A D VA N C E D U S E R S
All these features can be configured using program “ELDES Configuration Tool“
ATTENTION!
Value fields are separated by commas. Maximum SMS length is 160 characters. Only one input parameter can be configured by
one SMS message.
Examples of using SMSEXTRA command.
Suppose in all cases initial parameters were not changed and are manufacturer default.
1. Example of SMS message configuring Z1 input:
XXXX_SMSEXTRA:Z1:SC15,CC25,SE1234,CE4,LE1,DV900
This message configures Z1 input parameters.
SC15 means that during the alarm SMS message sending is disabled for users NO1 and NO5. As per manufacturer default settings
SMS sending is preset for all users, therefore users NO2, NO3 and NO4 SMS messages will still be delivered.
CC25 means that during the alarm calling function is disabled for users NO2 and NO5. As per manufacturer default settings, calling
function is preset for all users, therefore users NO1, NO3 and NO4 will still be called.
SE1234 means that SMS restore message sending is enabled for users NO1, NO2, NO3 and NO4. This means that when input Z1 is
restored after previous violation, these users will be informed about this restore event by SMS message. However, alarms and restore
SMS messages will be sent until the first successful delivery. To enable mandatory message delivery to all users you should use the
command XXXX_SMSALL:ON, as described in chapter 3.7.
CE4 means that during input Z1 restore only user NO4 is called.
LE1 means that input type for input Z1 will be inverted, i. e. the previous NO is changed to NC (normally closed). This means that the
input is violated only when the signal disappears, and the input is restored only in case when the signal appears.
DV900 means that input Z1 is violated only if the signal is suspended at least for 900ms. Please note that input type was inverted to
NC. (If inversion was not possible this DV900 command would mean that the signal transmitted must not be shorter than 900ms.)
2. Example of SMS message configuring Z2 input:
XXXX_SMSEXTRA:Z2:IE1,IC555
This message configures Z2 input parameters.
IE1 means that impulse counting mode is enabled for Z2 input.
IC555 means that the users will receive the alarm when 555 impulses are transmitted to the input. Immediately after the alarm the
counter resets and starts counting impulses until their number reaches 555.
To see the preset values for any command send SMS message with the same format that you use when changing parameters; only
Value structure will have no value:
XXXX_SMSEXTRA:Zn:Value1,Value2,……,ValueN
XXXX – user password.
Zn – possible values Z1,Z2,Z3,Z4,Z5. Define the number of the input being changed.
Value structure is Cn, where Cn is command name (2 letters). E. g. XXXX_SMSEXTRA:Z2:SS,SC,CC,SE,SD
26
ESIM 252
XXXX_
SMSEXTRA:
Z2:SS,SC,
CC,SE,SD
F O R A D VA N C E D U S E R S
All these features can be configured using program “ELDES Configuration Tool“
3.9.2 Additional possibilities of controlling and configuring outputs C1 and C2
Normally C1 and C2 outputs can be controlled only by SMS message, as described in chapter 3.6, i. e. by enabling/disabling it for
a permanent status or for a preset period. However, you can configure automatic enabling and disabling for a particular hour or
control this function by a call.
3.9.2.1 Settings of an output controlled by calls
When calling on the number of system ESIM251 the call is rejected and no control operations are run. However, when a special mode
is enabled C1/C2 outputs can be controlled by a call. It can be controlled by all users NO1-NO5, several users or only one of them.
By calling the system you can enable these 3 functions: enable/disable, enable/disable for a certain period or change output status
with every call, i. e. one call enables the status, the next one disables it etc.
The parameters are changed by sending the following SMS message to the system Esim252:
XXXX_SMSEXTRA:COCx:Value1,Value2,……,ValueN
XXXX – user password. COCx - output control by call; value can be COC1 (C1 output) or COC2 (C2 output). ValueN structure is CnVal,
when Cn is command name ((2 letters), and Val-its value).
Value (CnVal) – table of values
Cn – command Val – possible
name (2
command
letters)
meaning.
Enabling control
via call
Enabling/
disabling
confirmation call
(CallBack)
Confirmation
call duration
parameters
Enabling/
disabling
confirmation
SMS
(SMS confirm)
Command
description
Control via call mode
is enabled for users
No:1,2,3,4,5
Control via call modes
is disabled for users
No:1,2,3,4,5
Initial factory
default values
E. g. CE25 means that users NO2 and NO5 will be
able to control the output via call.
CE
1,2,3,4,5
CD
1,2,3,4,5
CS
1,2,3,4,5
Confirmation call
mode is enabled for
users No:1,2,3,4,5.
CC
1,2,3,4,5
Confirmation call
mode is disabled for
users No:1,2,3,4,5..
1,2,3,4,5;1; s
Confirmation call
is made for users
No:1,2,3,4,5 when the
ouput is turned on.
s- call time in seconds
СT112
СT212
СT312
СT412
СT512
1,2,3,4,5;0; s
Confirmation call
is made for users
No:1,2,3,4,5 when the
output is turned off.
s- call time in seconds
СT108
СT208
СT308
СT408
СT508
SS
1,2,3,4,5
Confirmation SMS
mode is enabled for
users No:1,2,3,4,5.
SC
1,2,3,4,5
Confirmation SMS
mode is disabled for
users No:1,2,3,4,5.
CD12345
Disabled for all
users NO1-NO5.
CC12345
Disabled for all
users NO1-NO5.
CT
USER MANUAL ELDES ESIM252 V1.0
Comments
SC12345
Disabled for all
users NO1-NO5.
E. g. CD25 means that output control via call is
disabled for users NO2 and NO5.
E. g. CS124 means that when users NO1, NO2 and
NO4 control the output via call they will be notified
about a successful output status change by a
confirmation call.
E. g. CC124 means that when users NO1, NO2 and
NO4 control the output via call the call confirming
about a successful output status change is disabled
and users will not receive calls.
The first number refers to user number. The second
number is a command and the last number refers
to call time in seconds.
E. g. СT412 means that if confirmation call mode
is enabled, user NO4 will receive a call if he/she is
trying to turn on the output.
The system will call for 2 seconds.
The first number refers to user number. The second
number is a command and the last number refers
to call time in seconds.
E. g. СT408 means that if confirmation call mode
is enabled, user NO4 will receive a call if he/she is
trying to turn off the output.
The system will call for8 seconds.
E. g. SS124 means that when users NO1, NO2 and
NO4 control the output via call they will be notified
about a successful output status change by a
confirmation SMS message.
Before that the user has to turn on control from a
particular number by using CE command.
E. g. SC124 means that when users NO1, NO2 and
NO4 control the output via call the confirmation
SMS message informing about the successful
output status change is not sent.
27
F O R A D VA N C E D U S E R S
All these features can be configured using program “ELDES Configuration Tool“
Type of control
via call
Setting relay
impulse
duration
MS
MS
1,2,3,4,5 and 0
When users
No:1,2,3,4,5 call the
output is turned on.
1,2,3,4,5 and 1
When users
No:1,2,3,4,5 call the
output is turned off.
1,2,3,4,5 and 2
When users
No:1,2,3,4,5 call
output status is
changed (TOGGLE)
1,2,3,4,5 and
Th.m.s
Setting output
impulse duration for
users No:1,2,3,4,5.
h- hours, m- minutes,
seconds.
MS11
The first digit refer to user number. The second
digit refers to command. Therefore to set a
possibility for user NO1 to turn on the output via
call you have to use the command MS10
The first digit refer to user number. The second
digit refers to command. Therefore to set a
possibility for user NO1 to turn off the output via
call you have to use the command MS11
The first digits refer to user number. The last digit
refers to command. Therefore to set a possibility
for user NO1 to turn on the output by one call and
then disable it by the next call you have to se the
command MS12
E. g. to set the timer for 5 hours 10mins 3seconds
for user NO1 you have to use the command
MS1T5.10.3
This means that when afore mentioned user NO1
control the output via call the impulse duration is
5hours 10mins and 3seconds and after this period
the output returns to the previous state
Example of SMS message configuring C1 output:
XXXX_SMSEXTRA:COC1:CE1234,CS123,MS10,MS42,MS1T0.0.40
This message configures C1 output parameters.
CE1234 means that С1 output can be controlled by users NO1-NO4 (NO5 cannot control via call).
CS123 means that only users NO1, NO2 and NO3 will receive confirmation call.
MS10 means that when user NO1 calls the system he/she enables C1 input, but cannot disable it via call. The user can disable it via
SMS message if he/she knows the password.
MS42 means that when user NO4 calls the system he/she will either enable or disable output C1 (TOGGLE mode is on). It depends
on the output status before making a call.
MS1T0.0.40 means that when user NO1 make a call to the system, the output is turned on for 40seconds and then it automatically turns off.
To see the preset values for any command send SMS message with the same format that you use when changing parameters; only
Value structure will have no value. This does not apply to MS and CT commands. When requesting MS and CT parameters MS and
CT must be followed by one character – user number (1,2,3,4 or 5).:
XXXX_SMSEXTRA:COCx:Value1,Value2,……,ValueN
XXXX – user password. COCx - output control by call; value can be COC1 (C1 output) or COC2 (C2 output). ValueN structure is CnVal,
when Cn is command name ((2 letters). This does not apply to MS and CT commands. When requesting MS and CT parameters MS
and CT must be followed by one character – user number (1,2,3,4 or 5).
E. g. XXXX_SMSEXTRA:COC1:CE,CS,MS1,MS3
3.9.2.2 Settings of the output controlled by SMS messages
This chapter describes the ways of informing users when they are trying to open/close the relay output (-s) via SMS messages described in chapter 3.6. Parameters are changed by sending the following SMS message to system ESIM252:
XXXX_SMSEXTRA:OCSx:Value1,Value2,……,ValueN
XXXX – user password. OCSx - output control by SMS; value can be OCS1 (C1 output) or OCS2 (C2 output). Value structure is CnVal,
where Cn is command name (2 letters), and Val-its value (digits without spaces or punctuation marks).
28
F O R A D VA N C E D U S E R S
All these features can be configured using program “ELDES Configuration Tool“
Value (CnVal) – table of values
Cn – command
name (2 letters)
Val – possible
command
meaning.
Command description
CB
1
Confirmation call mode
is enabled for all users.
CB
0
Confirmation call mode
is disabled for all users.
1; s
All users receive
confirmation call when
the output is turned on;
s- call time in seconds
0; s
All users receive
confirmation call when
the output is turned off;
s- call time in seconds
SB
1
Confirmation SMS
mode is enabled for
all users.
SB
0
Confirmation SMS
mode is disbled for all
users.
Enabling/
disabling
confirmation call
(CallBack)
Confirmation call
duration
Enabling/
disabling
confirmation
SMS message
(SMS confirm)
Initial factory
default values
Comments
CB1 means that when users control the
output via SMS message they are notified
about a successful output status change
by a confirmation call.
CB0
Disabled for all
users NO1-NO5.
CB0 means that when users control
the output via SMS message they will
not receive a call informing about a
successful output status change.
СT12
The first digit is a command; the last digit
refers to call time in seconds. E. g. СT12
means that if confirmation call mode is
enabled the call will be forwarded to the
user who is trying to turn on the output.
The system will call for 2 seconds.
СT08
The first digit is a command; the last digit
refers to call time in seconds. E. g. СT08
means that if confirmation call mode is
enabled the call will be forwarded to the
user who is trying to turn off the output.
The system will call for 8 seconds.
CT
SB1
Enabled for all
users NO1-NO5.
SB1 means that when all users control
the output via SMS message they will
be informed about a successful output
status change by a confirmation SMS
message.
SB0 means that when all users control
the output via SMS message they will not
be informed about a successful output
status change by SMS message.
Example of SMS message configuring C2 output ways of information:
XXXX_SMSEXTRA:OCS2:CB1,CT13,CT06,SB1
This message configures C2 output parameters when controlled via SMS messages.
CB1 means that when the user turns on/off output С2, he/she receives a short confirmation call (Call Back).
CT13 means that when the output is turned on, confirmation call duration is 3 seconds.
CT06 means that when output is turned off confirmation call duration is 6 seconds.
SB1 means that confirmation message is sent informing about turning the output on/off.
To see the preset values for any command send SMS message with the same format that you use when changing parameters; only
Value structure will have no value:
XXXX_SMSEXTRA:OCSx:Value1,Value2,……,ValueN
XXXX – user password. OCSx - output control by SMS; value can be OCS1 (C1 output) or OCS2 (C2 output). Value structure is CnVal,
when Cn is command name (2 letters).
E. g. XXXX_SMSEXTRA:OCS2:CB,CT,SB
USER MANUAL ELDES ESIM252 V1.0
29
F O R A D VA N C E D U S E R S
All these features can be configured using program “ELDES Configuration Tool“
3.9.2.3
Output ontrol settings by event time
This chapter describes a possibility to control C1 and C2 outputs using timetable (scheduler). It can be, for instance, atomatic turning on every day at 18:00 and turning off after 5 hours.
The parameters are changed by sending the following SMS message to the system Esim252:
XXXX_SMSEXTRA:OCTEx:Value1,Value2,……,ValueN
XXXX – user password. OCTEx - output control by event time; value can be OCTE1 (C1 output) or OCTE2 (C2 output). Value structure
is CnVal, when Cn is command name (2 letters), and Val-its value.
Value (CnVal) – table of values
Cn – command
name (2
letters)
Setting enabling/
disabling time
Val –
possible
command
meaning.
h.m
WT
Command
description
Initial factory
default values
h hour m
minutes
Indicates the time for
enabling or disabling
output in hours and
minutes
E. g. WT18.10 means event start time. It can be
enabling and disabling. It depends on the set
ST value. A period PT must also be indicated,
otherwise relay status will not change. See below.
1
Relay is turned on
0
Relay is turned off
E. g. ST0 means that when the set time comes the
output is turned off by WT command.
h.m
Indicates the time in
hours and minutes for
which output status is
changed.
E. g. PT1.20 means that after automatic enabling/
disabling which is indicated in WT command relay
status is changed to opposite for 1 hour and 20
minutes.
1
Users are notified
about period start by
a confirmation call
CS1 means that the preset user is informed about
the period start of output turning on or off via
short call. The user is set by using UC command.
See below.
0
Users are not notified
about period start by
a confirmation call
1
Users are notified
about period end by a
confirmation call
0
Users are not notified
about period end by a
confirmation call
1; s
The user receives
a confirmation call
when the output is
turned on;
s- call time in seconds
ST1
Setting output
status, whether
it is enabled or
disabled
Setting the period
of turning on/off
Setting
confirmation call
for period start
Setting
confirmation call
for period end
Confirmation call
duration
30
ST
PT
Comments
h hour m
minutes
Output is
turned on
E. g. ST1 means that when the set time comes the
output is turned on by WT command.
CS
СS0
Call is not
made
CS0 means that nobody is informed about period
start by a call.
CE1 means that the preset user is informed about
the period end of output turning on or off via short
call. The user is set by using UC command.
See below.
CE
CT
СE0
Call is not
made
СT12
CE0 means that nobody is informed about period
end by a call.
The first digit is a command; the last digit refers
to call time in seconds. E. g. СT12 means that if
confirmation call mode is enabled, whether for
period start or end, the call will be forwarded to the
user when output is turned on. The system will call
for 2 seconds.
F O R A D VA N C E D U S E R S
All these features can be configured using program “ELDES Configuration Tool“
Setting the user
who receives
confirmations
about period
start/end
Setting
confirmation
SMS message for
period start
Setting
confirmation
SMS message for
period end
UC
0; s
The user receives
a confirmation call
when the output is
turned off;
s- call time in seconds
СT08
The first digit is a command; the last digit refers to
call time in seconds.
E. g. СT08 means that if confirmation call mode
is enabled, whether for period start or end, the
call will be forwarded to the user when output is
turned off. The system will call for 8 seconds.
1,2,3,4,5
Sets which user is
notified about period
start/end.
UC1
E. g. UC2 means that all confirmations will be
delivered to user No2.
Only one user can be selected.
1
Users are notified
about period start by
SMS message
0
Users are not notified
about period start by
SMS message
1
Users are notified
about period end by
SMS message
0
Users are not notified
about period end by
SMS message
SS
SE
SS1 means that the preset user is notified about
period start of turning on/off output by SMS
message. The user is set by using UC command.
See below.
SS0
SS0 means that nobody is informed about period
start by SMS message.
SE1 means that the user is also notified about
output turning off by SMS message.
SE0
SE0 means that nobody is informed about period
end by SMS message.
Example of output C1 configuration for a schedule:
XXXX_SMSEXTRA:OCTE1:WT20.15,ST1,PT8.0,UC2,CS1,CT13,CT06,SE1
This message configures C1 output parameters using a schedule.
WT20.15 means that output turning on time is set for 20:15 every day.
ST1 means the user set the output to turn on on that time.
PT8.5 means that the output is turned on for 8 hours and 5 minutes, and after that it turns off and turns on again at 20:15 the
following day etc.
UC2 means that information about turning on/off is sent to user’s No2 telephone.
CS1 means that the user is notified by a callback about output turning on; the duration of the call is set by parameter CT13. CT13
means that the system calls for 3 seconds.
CT06 means that when the output turns off after 8 hours and 5 minutes the user is notified by a call again, but call duration is 6
seconds.
SE1 means that the user is also notified about relay enabling by SMS message.
To see the preset values for any command send SMS message with the same format that you use when changing parameters; only
Value structure will have no value:
XXXX_SMSEXTRA:OCTE1:Value1,Value2,……,ValueN
XXXX – user password. OCTEx - output control by event time; value can be OCTE1 (C1 output) or OCTE2 (C2 output). Value structure
is Cn, where Cn is command name (2 letters).
E. g. XXXX_SMSEXTRA:OCTE1:CB,CT,SB
USER MANUAL ELDES ESIM252 V1.0
31
4. Appendix
4.1 Restoring Default Parameters
To restore default parameters:
• disconnect power supply and USB connector
• short circuit (connect) connectors D1 and D2
• power up the system for 5 seconds
• disconnect power supply
• remove short circuit from connectors D1 and D2
• power up the system
• parameters restored to default
4.2 ELDES Configuration Tool Software
To configure the system quicker and easier as well as use more system capabilities use configuration software ELDES Configura­tion
Tool which can be downloaded from our website www.eldes.lt
Before configuring ESIM252 via USB cable or remote configuration over GPRS, please, read ELDES Configuration Tool user guide
available in HELP section of the software.
4.3 Technical Support
Indication
Indicator is off or not blinking
Possible reason
· no external power supply
· circuit not properly connected
· blown fuse
· no network signal
Indicator blinking several times per · SIM card is not inserted
second
· PIN code hasn’t been disabled
· Sim card not active
System does not send any SMS
· SIM card account depleted
messages and/or does not ring
· incorrect SIM central number
· no network signal
· user number is not programmed
(or disabled access from unknown numbers)
Received SMS message “Incorrect
· incorrect syntax
Format”
· extra space symbol left in SMS message
No sound while listening to remote · microphone not connected
microphone
· microphone connection incorrect
While listening to remote micropho- · Change the position of the microphone or its lead in ne outside noise heard
respect of system panel
If your problem could not be fixed by the self-guide above, please contact your distributor or manufacturer tech support by email
[email protected] More up to date information about your device and other products can be found at the manufacturer’s website
www.eldes.lt
32
USER MANUAL ELDES ESIM252 V1.0
33
For notes
34
For notes
USER MANUAL ELDES ESIM252 V1.0
35
Made in Lithuania.
www.eldes.lt
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertisement