1 of 4
Q U ICK STA R T G U I DE
Model 25-K1
1
Carefully unpack box and make sure you have all items
shown below.
What’s what?
Important components labeled
Unit shown with front panel fully open.
Internal wiring not shown for clarity.
Antenna Cables
Ascent Unit
r
12-V AC/DC Adapter
(PS-12DC1)
I M P O R T A NT !
2
Key
Carriage Bolt
( x4 )
Hex Nut
( x4 )
Unlock and open front panel
of unit for wiring and setup.
Relay Status LEDs
Relay is active when lit
We recommend mounting Ascent on a
gooseneck pedestal using included hardware.
If using alternate mounting, two (2)
Ascent 10' Cable Extension (p/n 16-X-EXT)
products should be purchased and installed.
Connection Terminals
For wiring to all external devices including
gate operator or door opener
Failure to do so may result in NO SIGNAL!
Power Terminals
For wiring to compatible AC/DC power source
Continued on next page...
r
I M P O R TA NT !
Ascent WILL NOT WORK until the
activation process is COMPLETE!
Follow the Activation Guide or call
Summit Control at (844) 259-8265 to
activate your unit.
W AR N I N G !
AUTOMATIC GATES CAN CAUSE
SERIOUS INJURY OR DEATH!
ALWAYS CHECK that the GATE PATH
IS CLEAR BEFORE OPERATING!
Reversing or other safety devices
should ALWAYS BE USED!
SIM Card
If you have your own SIM card, see Page 4
and follow the instructions entitled,
Installing a Third-Party SIM Card.
C A U TIO N !
Please use all four screws when mounting unit to pedestal. Leave “hockey puck” antenna
in place, even if using extension. Seal any holes or gaps created in unit enclosure.
Failure to follow these instructions can result in damage to the unit!
2 of 4
QUIC K STAR T GU I DE
Ascent Connection Terminals
Before going forward,
double check wiring and
ensure unit has power!
For additional wiring
options, see Page 3.
© 2018 Security Brands, Inc. All rights reserved.
4
Consult gate operator or
door opener manual for
exact connections.
12-V AC/DC Adapter
(Model PS-12DC1 included)
Terminals vary widely
across manufacturers
and models.
The GROUND terminal is optional unless
required by local code(s). If using, please
connect to earth ground or equivalent.
Close and lock front panel.
5
Make sure gate path is clear, then
key in temporary code 2012 on
keypad and confirm gate opens.
2
0
1
2
Adding and deleting codes is done through
Summit Control and NOT from the keypad!
CLOSE
STOP
OPEN
POS. (+)
N/C
COM
N/O
N/C
N/O
GND
N/O
GND
#2
GND
#1
COM
Relay B can be wired to a second device
in the same manner.
OR
Third-Party 12–24-VAC/DC
Power Source
S T OP !
CLOSE
OPEN
POS. (+)
NEG. (–)
If plugging into duplex outlet,
remove screw from outlet plate,
and secure with included screw.
COM
J4
REVERSE LOOP
J5
J6
POWER
J3
+ –
J9
12–24 VAC/DC
COM
Ascent
Power
Terminals
J8
RELAY A
FREE EXIT
J7
POWER
RELAY B
COM
12–24 VAC/DC
DIGITAL INPUTS EVENT
RADIO
STATUS
Gate Operator / Door Opener
COM
Feed wires through back of unit
and connect as shown.
NEG. (–)
Connect wires
GND
3
Model 25-K1
Additional wiring diagrams
can be found on Page 3.
C A U TIO N !
If you will not be using the 12-V AC/DC adapter,
please go to Page 4 and follow the procedure,
Using a Third-Party Power Source.
Do not exceed 24 VAC/DC! Failure to choose a
compatible power source can damage unit!
N
INSTALLATION COMPLETE!
Now follow the Activation Guide to create
an account and begin using Ascent.
QSG-25K1-EN
Rev. D (6/2018)
3 of 4
QUIC K STAR T GU I DE
Connected as
shown in Step 3
Optional
wire
splices
N/C
COM
N/C
Open Limit Switch
N/O
COM
Gate Operator
N/C
Connected as
shown in Step 3
Close Limit Switch
N/O
COM
J4
N/O
J5
J6
N/C
RELAY A
N/O
J9
RELAY B
COM
J8
CLOSE
GND
OPEN
J7
DIGITAL INPUTS EVENT
GND
STATUS
N/O
Exceeding 3 V can damage Ascent!
N/C
N/O
GND
COM
J4
N/O
J5
N/C
RELAY A
COM
RELAY B
J6
N/O
J9
GND
GND
#1
J8
CLOSE
GND
OPEN
J7
DIGITAL INPUTS EVENT
#2
STATUS
Ascent Connection Terminals
GND
Ascent Connection Terminals
Wiring for accessories such as a request-to-exit device
#2
The Status Terminals are designed for
low voltage (3 V or less). Check the
voltage on your status wires before
connecting. If it is above 3 V, you will
need to contact Technical Support.
B Event Input
#1
Wiring to enable Gate Status Check
CAU T I ON !
GND
A Status Check
Model 25-K1
Request-to-Exit
(if equipped with limit switches)
(S-RTE-P is shown)
4 of 4
QUIC K STAR T GU I DE
Model 25-K1
IMP OR T AN T !
r
Using a
Third-Party
Power Source
(Optional)
If you would like to use a third-party
power source, such as solar, verify that
it conforms to the following specs:
Input
12–24 VAC/DC
no more than 10% beyond this range
Current Draw
1
Installing a
Third-Party
SIM Card
(Optional)
?
© 2018 Security Brands, Inc. All rights reserved.
less than 190 mA @ 12 VDC
less than 160 mA @ 24 VDC
3a
Connect wires to unit as shown in
Step 3.
3b
Connect wires to your power source,
making sure you connect positive to
positive and negative to negative.
2
Remove existing SIM card and locate
new SIM card.
Push existing SIM card in until it
unlocks with “click” sound.
NEED HELP
C A U TIO N !
Double check that you’ve wired from
positive on Ascent to positive on your
power source and negative on Ascent to
negative on your power source.
Reverse polarity can damage Ascent!
3
Insert new SIM card until it locks in
place with “click” sound.
Call (844) 259-8265
Email [email protected]
We are available Mon–Fri / 8am–5pm Central
QSG-25K1-EN
Rev. D (6/2018)
">
