PowerFlex® 40P Adjustable Frequency AC Drive !

PowerFlex® 40P Adjustable Frequency AC Drive !
PowerFlex® 40P Adjustable
Frequency AC Drive
Quick Start
FRN 1.xx - 2.xx
This Quick Start guide summarizes the basic steps needed to install,
start-up and program the PowerFlex 40P Adjustable Frequency AC
Drive. The information provided Does Not replace the User Manual
and is intended for qualified drive service personnel only.
For detailed PowerFlex 40P information including EMC instructions,
application considerations and related precautions refer to the
PowerFlex 40P User Manual, Publication 22D-UM001 on the CD
supplied with the drive or at www.rockwellautomation.com/literature.
General Precautions
!
ATTENTION: The drive contains high voltage capacitors which take
time to discharge after removal of mains supply. Before working on
drive, ensure isolation of mains supply from line inputs [R, S, T (L1,
L2, L3)]. Wait three minutes for capacitors to discharge to safe voltage
levels. Failure to do so may result in personal injury or death.
Darkened display LEDs is not an indication that capacitors have
discharged to safe voltage levels.
ATTENTION: Equipment damage and/or personal injury may result
if parameter A092 [Auto Rstrt Tries] or A094 [Start At PowerUp] is
used in an inappropriate application. Do not use this function without
considering applicable local, national and international codes,
standards, regulations or industry guidelines.
ATTENTION: Only qualified personnel familiar with adjustable
frequency AC drives and associated machinery should plan or
implement the installation, start-up and subsequent maintenance of the
system. Failure to comply may result in personal injury and/or
equipment damage.
ATTENTION: This drive contains ESD (Electrostatic Discharge)
sensitive parts and assemblies. Static control precautions are required
when installing, testing, servicing or repairing this assembly.
Component damage may result if ESD control procedures are not
followed. If you are not familiar with static control procedures,
reference A-B publication 8000-4.5.2, “Guarding Against Electrostatic
Damage” or any other applicable ESD protection handbook.
ATTENTION: An incorrectly applied or installed drive can result in
component damage or a reduction in product life. Wiring or application
errors, such as, undersizing the motor, incorrect or inadequate AC
supply, or excessive ambient temperatures may result in malfunction of
the system.
ATTENTION: Risk of injury or equipment damage exists. Drive does
not contain user-serviceable components. Do not disassemble drive
chassis.
English-2
Mounting Considerations
•
Mount the drive upright on a flat, vertical and level surface.
Frame
B
C
•
•
•
Screw Size
M4 (#8-32)
M5 (#10-24)
Screw Torque
1.56-1.96 N-m (14-17 lb.-in.)
2.45-2.94 N-m (22-26 lb.-in.)
DIN Rail
35 mm
–
Protect the cooling fan by avoiding dust or metallic particles.
Do not expose to a corrosive atmosphere.
Protect from moisture and direct sunlight.
Minimum Mounting Clearances
See page 20 for mounting dimensions.
120 mm
(4.7 in.)
120 mm
(4.7 in.)
25 mm
(1.0 in.)
RUN
REV
FAULT
RUN
REV
FAULT
Closest object that
may restrict air flow
through the drive heat
sink and chassis
120 mm
(4.7 in.)
RUN
REV
FAULT
RUN
REV
FAULT
120 mm
(4.7 in.)
Mounting Option A
No clearance required
between drives.
Mounting Option B
Ambient Operating Temperatures
Ambient Temperature
Minimum
Maximum
-10°C (14°F)
(1)
Enclosure Rating
Minimum Mounting
Clearances
IP 20/Open Type
Use Mounting Option A
IP 30/NEMA 1/UL Type 1(1) Use Mounting Option B
50°C (122°F) IP 20/Open Type
Use Mounting Option B
40°C (104°F)
Rating requires installation of the PowerFlex 40P IP 30/NEMA 1/UL Type 1 option kit.
English-3
Typical Grounding
RUN
REV
FAULT
R/L1
S/L2
T/L3
U/T1
V/T2
W/T3
SHLD
Disconnecting MOVs
To prevent drive damage, the MOVs connected to ground shall be
disconnected if the drive is installed on an ungrounded distribution
system where the line-to-ground voltages on any phase could exceed
125% of the nominal line-to-line voltage. To disconnect these devices,
remove the jumper shown in the figures below.
1. Turn the screw counterclockwise to loosen.
2. Pull the jumper completely out of the drive chassis.
3. Tighten the screw to keep it in place.
Jumper Location
Phase to Ground MOV Removal
R/L1
Three-Phase
AC Input S/L2
T/L3
Jumper
Important: Tighten screw after jumper removal.
1
2
3
4
English-4
CE Conformity
Refer to the PowerFlex 40P User Manual, Publication 22D-UM001 on
the CD supplied with the drive for details on how to comply with the
Low Voltage (LV) and Electromagnetic Compatibility (EMC) Directives.
Specifications, Fuses and Circuit Breakers
Drive Ratings
Catalog
Number(1)
Output Ratings
kW (HP)
Amps
Input Ratings
Voltage
Range
kVA
Amps
Branch Circuit Protection
140M Motor
Fuses
Protectors
Contactors
200 - 240V AC (±10%) – 3-Phase Input, 0 - 230V 3-Phase Output
22D-B2P3
0.4 (0.5)
2.3
180-264
1.15
2.5
6
140M-C2E-B40
100-C07
22D-B5P0
0.75 (1.0)
5.0
180-264
2.45
5.7
10
140M-C2E-C10
100-C09
22D-B8P0
1.5 (2.0)
8.0
180-264
4.0
9.5
15
140M-C2E-C16
100-C12
22D-B012
2.2 (3.0)
12.0
180-264
5.5
15.5
25
140M-C2E-C16
100-C23
22D-B017
3.7 (5.0)
17.5
180-264
8.6
21.0
30
140M-F8E-C25
100-C23
22D-B024
5.5 (7.5)
24.0
180-264
11.8
26.1
40
140M-F8E-C32
100-C37
22D-B033
7.5 (10.0)
33.0
180-264
16.3
34.6
60
140M-G8E-C45
100-C60
380 - 480V AC (±10%) – 3-Phase Input, 0 - 460V 3-Phase Output
22D-D1P4
0.4 (0.5)
1.4
342-528
1.4
1.8
3
140M-C2E-B25
100-C07
22D-D2P3
0.75 (1.0)
2.3
342-528
2.3
3.2
6
140M-C2E-B40
100-C07
22D-D4P0
1.5 (2.0)
4.0
342-528
4.0
5.7
10
140M-C2E-B63
100-C09
22D-D6P0
2.2 (3.0)
6.0
342-528
5.9
7.5
15
140M-C2E-C10
100-C09
22D-D010
4.0 (5.0)
10.5
342-528
10.3
13.0
20
140M-C2E-C16
100-C23
22D-D012
5.5 (7.5)
12.0
342-528
11.8
14.2
25
140M-D8E-C20
100-C23
22D-D017
7.5 (10.0)
17.0
342-528
16.8
18.4
30
140M-D8E-C20
100-C23
22D-D024
11.0 (15.0)
24.0
342-528
23.4
26.0
50
140M-F8E-C32
100-C43
100-C09
460 - 600V AC (±10%) – 3-Phase Input, 0 - 575V 3-Phase Output
22D-E1P7
0.75 (1.0)
1.7
414-660
2.1
2.3
6
140M-C2E-B25
22D-E3P0
1.5 (2.0)
3.0
414-660
3.65
3.8
6
140M-C2E-B40
100-C09
22D-E4P2
2.2 (3.0)
4.2
414-660
5.2
5.3
10
140M-C2E-B63
100-C09
22D-E6P6
4.0 (5.0)
6.6
414-660
8.1
8.3
15
140M-C2E-C10
100-C09
22D-E9P9
5.5 (7.5)
9.9
414-660
12.1
11.2
20
140M-C2E-C16
100-C16
22D-E012
7.5 (10.0)
12.2
414-660
14.9
13.7
25
140M-C2E-C16
100-C23
22D-E019
11.0 (15.0)
19.0
414-660
23.1
24.1
40
140M-D8E-C25
100-C30
(1)
Ratings apply to all drive types; Panel Mount (N104), Flange Mount (F104), and Plate Drive
(H204).
English-5
Category
Agency
Certification
Specification
C
UL
®
Listed to UL508C and CAN/CSA-22.2
US
Certified to AS/NZS, 1997 Group 1, Class A
Marked for all applicable European Directives
EMC Directive (89/336)
EN 61800-3, EN 50081-1, EN 50082-2
Low Voltage Directive (73/23/EEC)
EN 50178, EN 60204
Certified to EN 954-1, Category 3.
..
EN 50178
Meets Functional Safety (FS) when used with the
TUV
E C
Rheinland
DriveGuard Safe-Off Option (Series B).
The drive is also designed to meet the appropriate portions of the following specifications:
NFPA 70 - US National Electrical Code
NEMA ICS 3.1 - Safety standards for Construction and Guide for Selection, Installation and
Operation of Adjustable Speed Drive Systems.
IEC 146 - International Electrical Code.
Bus Overvoltage Trip
200-240V AC Input:
405V DC bus (equivalent to 290V AC incoming line)
380-460V AC Input:
810V DC bus (equivalent to 575V AC incoming line)
460-600V AC Input:
1005V DC bus (equivalent to 711V AC incoming line)
Bus Undervoltage Trip
200-240V AC Input:
210V DC bus (equivalent to 150V AC incoming line)
380-480V AC Input:
390V DC bus (equivalent to 275V AC incoming line)
460-600V AC Input
P042 = 3 “High Voltage”:
487V DC bus (equivalent to 344V AC incoming line)
P042 = 2 “Low Voltage”:
390V DC bus (equivalent to 275V AC incoming line)
Power Ride-Thru:
100 milliseconds
Logic Control Ride-Thru:
0.5 seconds minimum, 2 seconds typical
Electronic Motor Overload Protection:
I2t protection - 150% for 60 seconds, 200% for 3
seconds (Provides Class 10 protection)
Overcurrent:
200% hardware limit, 300% instantaneous fault
Ground Fault Trip:
Phase-to-ground on drive output
Short Circuit Trip:
Phase-to-phase on drive output
Altitude:
1000 m (3300 ft) max. without derating. Above 1000 m
(3300 ft) derate 3% for every 305 m (1000 ft).
Maximum Surrounding Air Temperature
without derating:
IP20, Open Type:
–10 to 50° C (14 to 122° F)
IP30, NEMA Type 1, UL Type 1:
–10 to 40° C (14 to 104° F)
Flange and Plate Mount:
Heatsink: –10 to 40° C (14 to 104° F)
Drive:
–10 to 50° C (14 to 122° F)
Cooling Method
Convection:
0.4 kW (0.5 HP) drives and all Flange and Plate drives
Fan:
All other drive ratings
Storage Temperature:
–40 to 85 degrees C (–40 to 185 degrees F)
Atmosphere:
Important: Drive must not be installed in an area
where the ambient atmosphere contains volatile or
corrosive gas, vapors or dust. If the drive is not going
to be installed for a period of time, it must be stored in
an area where it will not be exposed to a corrosive
atmosphere.
Relative Humidity:
0 to 95% non-condensing
Shock (operating):
15G peak for 11ms duration (±1.0 ms)
Vibration (operating):
1G peak, 5 to 2000 Hz
Voltage Tolerance:
200-240V ±10%
380-480V ±10%
460-600V ±10%
Frequency Tolerance:
48-63 Hz
Input Phases:
Three-phase input provides full rating. Single-phase
operation provides 35% rated current.
Displacement Power Factor:
0.98 across entire speed range
Maximum Short Circuit Rating:
100,000 Amps Symmetrical
Actual Short Circuit Rating:
Determined by AIC Rating of installed fuse/circuit
breaker
Transistor Type:
Isolated Gate Bipolar (IGBT)
Bauart geprüft
Functional
Protection
Environment
Electrical
W
..
TUV
Rheinland
Product Safety
Production inspected
Safety
Type approved
English-6
Category
Control
Specification
Method:
Carrier Frequency
Frequency Accuracy
Digital Input:
Analog Input:
Analog Output:
Speed Regulation
Open Loop with Slip Compensation:
With Encoder:
Output Frequency:
Efficiency:
Stop Modes:
Accel/Decel:
Intermittent Overload:
Electronic Motor Overload Protection
Control Inputs
Digital:
Analog:
Encoder
Bandwidth:
Quantity:
Current:
Type
Source Mode (SRC):
Sink Mode (SNK):
Quantity:
Specification
Resolution:
0 to 10V DC Analog:
4-20mA Analog:
External Pot:
Type:
Supply:
Quadrature:
Duty Cycle:
Requirements:
Control Outputs Relay:
Opto:
Analog:
Quantity:
Specification
Resistive Rating:
Inductive Rating:
Quantity:
Specification:
Quantity:
Specification
Resolution:
0 to 10V DC Analog:
4-20mA Analog:
Sinusoidal PWM, Volts/Hertz, and Sensorless Vector
2-16 kHz, Drive rating based on 4 kHz.
Within ±0.05% of set output frequency
Within 0.5% of maximum output frequency, 10-Bit
resolution
±2% of full scale, 10-Bit resolution
±1% of base speed across a 80:1 speed range
±0.3% of base speed across a 80:1 speed range
±0.05% of base speed across a 20:1 speed range
0-500 Hz (programmable)
97.5% (typical)
Multiple programmable stop modes including - Ramp,
Coast, DC-Brake, and Ramp-to-Stop
Four independently programmable accel and decel
times. Each time may be programmed from 0 - 600
seconds in 0.1 second increments.
150% Overload capability for up to 1 minute
200% Overload capability for up to 3 seconds
Class 10 protection with selectable speed sensitive
response and power-down overload retention function
when enabled.
10 Rad/Secs for open and closed loop
(2) Semi-programmable
(5) Programmable
6 mA
18-24V = ON, 0-6V = OFF
0-6V = ON, 18-24V = OFF
(2) Isolated, –10 to 10V and 4-20mA
10-bit
100k ohm input impedance
250 ohm input impedance
1-10k ohm, 2 Watt minimum
Incremental, dual channel
12V, 250 mA. 12V, 10 mA minimum inputs isolated
with differential transmitter, 250 kHz maximum.
90°, ±27 degrees at 25 degrees C.
50%, +10%
Encoders must be line driver type, quadrature (dual
channel) or pulse (single channel), 3.5-26V DC output,
single-ended or differential and capable of supplying a
minimum of 10 mA per channel. Allowable input is DC
up to a maximum frequency of 250 kHz. The encoder
I/O automatically scales to allow 5V, 12V and 24V DC
nominal voltages.
(1) Programmable Form C
3.0A at 30V DC, 3.0A at 125V, 3.0A at 240V AC
0.5A at 30V DC, 0.5A at 125V, 0.5A at 240V AC
(2) Programmable
30V DC, 50mA Non-inductive
(1) Non-Isolated 0-10V or 4-20mA
10-bit
1k ohm minimum
525 ohm maximum
English-7
Power Wiring
Power Wire Rating
Recommended Copper Wire
Unshielded 600V, 75°C (167°F) THHN/THWN
15 Mils insulated, dry location
Shielded 600V, 75°C or 90°C (167°F or 194°F) RHH/
RHW-2
Anixter OLF-7xxxxx,
Belden 29501-29507 or
equivalent
Shielded Tray rated 600V, 75°C or 90°C (167°F or
194°F) RHH/RHW-2
Anixter 7V-7xxxx-3G
Shawflex 2ACD/3ACD or
equivalent
Power Terminal Block
B Frame
C Frame
R/L1 S/L2 T/L3 U/T1 V/T2 W/T3
R/L1 S/L2 T/L3 U/T1 V/T2 W/T3
DC- DC+ BR+ BR-
Terminal (1)
Description
R/L1, S/L2
1-Phase Input (2)
P2
P1
DC- DC+ BR+ BR-
R/L1, S/L2, T/L3 3-Phase Input
U/T1
To Motor U/T1
V/T2
To Motor V/T2
W/T3
To Motor W/T3
Switch any two motor
leads to change
forward direction.
=
DC Bus Inductor Connection (C Frame drives only.)
P2, P1
The C Frame drive is shipped with a jumper between
Terminals P2 and P1. Remove this jumper only when a DC
Bus Inductor will be connected. Drive will not power up
without a jumper or inductor connected.
DC+, DC-
DC Bus Connection
BR+, BR-
Dynamic Brake Resistor Connection
Safety Ground - PE
(1)
(2)
Important: Terminal screws may become loose during shipment. Ensure that all
terminal screws are tightened to the recommended torque before applying power to
the drive.
Single-phase operation requires a 65% derate of drive rated current.
Power Terminal Block Specifications
Frame
Maximum Wire Size (1) Minimum Wire Size (1) Torque
B
5.3 mm2 (10 AWG)
C
(1)
2
8.4 mm (8 AWG)
1.3 mm2 (16 AWG)
2
1.3 mm (16 AWG)
1.7-2.2 N-m (16-19 lb.-in.)
2.9-3.7 N-m (26-33 lb.-in.)
Maximum/minimum sizes that the terminal block will accept - these are not
recommendations.
English-8
Input Power Conditions
Input Power Condition
Corrective Action
Low Line Impedance (less than 1% line reactance) • Install Line Reactor(2)
• or Isolation Transformer
Greater than 120 kVA supply transformer
• or Bus Inductor – 5.5 & 11 kW
(7.5 & 15 HP) drives only
Line has power factor correction capacitors
Line has frequent power interruptions
• Install Line Reactor
• or Isolation Transformer
Line has intermittent noise spikes in excess of
6000V (lightning)
Phase to ground voltage exceeds 125% of normal
line to line voltage
Ungrounded distribution system
240V open delta configuration (stinger leg)(1)
(1)
(2)
• Remove MOV jumper to ground.
• or Install Isolation Transformer
with grounded secondary if
necessary.
• Install Line Reactor
For drives applied on an open delta with a middle phase grounded neutral system, the
phase opposite the phase that is tapped in the middle to the neutral or earth is
referred to as the “stinger leg,” “high leg,” “red leg,” etc. This leg should be identified
throughout the system with red or orange tape on the wire at each connection point.
The stinger leg should be connected to the center Phase B on the reactor. Refer to the
PowerFlex 40P User Manual on CD for specific line reactor part numbers.
Refer to Appendix B of the PowerFlex 40P User Manual on CD for accessory ordering
information.
Common Bus/Precharge Notes
If drives with internal precharge are used with a disconnect switch to the
common bus, then an auxiliary contact on the disconnect must be
connected to a digital input of the drive. The corresponding input
(parameter A051-A054) must be set to option 29, “Precharge Enable.”
This provides the proper precharge interlock, guarding against possible
damage to the drive when connected to a common DC bus.
English-9
I/O Wiring Recommendations
Signal and Control Wire Types
Belden Wire Type(s)(1)
(or equivalent)
Description
8760/9460
0.750 mm2 (18AWG), twisted
pair, 100% shield with drain (3)
Remote Pot
8770
0.750 mm2 (18AWG), 3
cond., shielded
Encoder/Pulse I/O 89730 (2)
0.196 mm2 (24AWG),
individually shielded pairs
Signal Type/
Where Used
Analog I/O & PTC
(1)
(2)
(3)
Min. Insulation
Rating
300V,
75-90° C
(167-194° F)
Stranded or solid wire.
9728 or 9730 are equivalent and may be used but may not fit in the drive wire channel.
If the wires are short and contained within a cabinet which has no sensitive circuits,
the use of shielded wire may not be necessary, but is always recommended.
Recommended Control Wire for Digital I/O
Type
Wire Type(s)
Unshielded Per US NEC or applicable
national or local code
Shielded
Multi-conductor shielded
cable such as Belden
8770(or equiv.)
Minimum
Insulation Rating
300V,
60 degrees C
0.750 mm2 (18AWG), 3 (140 degrees F)
conductor, shielded.
Description
–
I/O Terminal Block Specifications
Frame
Maximum Wire Size (1) Minimum Wire Size (1) Torque
B&C
1.3 mm2 (16 AWG)
(1)
0.2 mm2 (24 AWG)
0.5-0.8 N-m (4.4-7 lb.-in.)
Maximum/minimum sizes that the terminal block will accept - these are not
recommendations.
Refer to the PowerFlex 40P User Manual, Publication 22D-UM001 on
CD for maximum power and control cable length recommendations.
English-10
Control Terminal Block
Control Wiring Block Diagram
Enable Jumper
(6)
01
02
03
SNK
SRC
04
05
06
07
08
09
+24V
11
+10V
12
13
14
Relay N.O.
Relay Common
Relay N.C.
15
R1
0-10V
R2
0/4-20mA
16
17
R3
18
30V DC
50mA
Non-inductive
Typical
SRC Wiring
(1)(6)
Start/Run FWD
+/-10V
0-20mA
(2)
Direction/Run REV
(3)
Digital Common
Digital Input 1
Digital Input 2
Digital Input 3
Digital Input 4
Opto Common
+24V DC
+10V DC
0-10V (or ±10V) Input
(4)
Analog Common
Pot must be
1-10k ohm
2 Watt Min.
4-20mA Input
Analog Output
Common
Opto Output 1
Opto Output 2
RS485 Shield
(4)
10V
Voltage Range Select
ENBL
SNK
Enable
Jumper
(1)
125V AC
3.0A
0.5A
(6)
01 02 03 04 05 06 07 08 09
11 12 13 14 15 16 17 18 19
30V DC
3.0A
0.5A
(5)
24V
SRC
Resistive
Inductive
Typical
SNK Wiring
Analog Output Select
0-10V
R1 R2 R3
19
Stop
240V AC
3.0A
0.5A
See Control Wiring Block Diagram Notes on next page.
RS485
(DSI)
1
English-11
Control Wiring Block Diagram Notes
(1)
Important: I/O Terminal 01 is always a coast to stop input except when P036 [Start
Source] is set to “3-Wire”, “2-W Lvl Sens” or “Momt FWD/REV” control. In three wire
control, I/O Terminal 01 is controlled by P037 [Stop Mode]. All other stop sources are
controlled by P037 [Stop Mode].
P036 [Start Source]
3-Wire
2-Wire
2-W Lvl Sens
2-W Hi Speed
RS485 Port
Momt FWD/REV
Stop
Per P037
Per P037
Per P037
Per P037
Per P037
Per P037
I/O Terminal 01 Stop
Per P037(6)
Coast
Per P037(6)
Coast
Coast
Per P037(6)
Important: The drive is shipped with a jumper installed between I/O Terminals 01 and
11. Remove this jumper when using I/O Terminal 01 as a stop or enable input.
(2)
Two wire control shown. For three wire control use a momentary input
on I/O
Terminal 02 to command a start. Use a maintained input
for I/O Terminal 03 to
change direction.
(3)
The function of I/O Terminal 03 is fully programmable. Program with E202 [Digital
Term 3].
(4)
Match the Voltage Range Select DIP switch setting with the control scheme for proper
Uni-Polar or Bipolar operation.
(5)
When using an opto output with an inductive load such as a relay, install a recovery
diode parallel to the relay as shown, to prevent damage to the output.
(6)
When the ENBL enable jumper is removed, I/O Terminal 01 will always act as a
hardware enable, causing a coast to stop without software interpretation.
English-12
Control I/O Terminal Designations
No. Signal
Default
Description
Param.
R1
Relay N.O.
Fault
Normally open contact for output relay.
A055
R2
Relay Common
–
Common for output relay.
R3
Relay N.C.
Fault
Normally closed contact for output relay.
Analog Output Select
DIP Switch
0-10V
Sets analog output to either voltage or current. Setting must match
A065 [Analog Out Sel].
Sink/Source
DIP Switch
Source (SRC)
Inputs can be wired as Sink (SNK) or Source (SRC) via DIP Switch
setting.
Stop (1)
Coast
The factory installed jumper or a normally closed
input must be present for the drive to start.
02
Start/Run FWD
Not Active
03
Digital Term 3
Not Active
I/O Terminal 03 is fully programmable. Program with P036, P037
E202 [Digital Term 3]. To disable reverse operation, P036, P037,
see A095 [Reverse Disable].
A095, E202
04
Digital Common
–
For digital inputs. Electronically isolated with digital
inputs from analog I/O and opto outputs.
05
Digital Input 1
Preset Freq
Program with A051 [Digital In1 Sel].
A051
06
Digital Input 2
Preset Freq
Program with A052 [Digital In2 Sel].
A052
07
Digital Input 3
Local
Program with A053 [Digital In3 Sel].
A053
08
Digital Input 4
Jog Forward
Program with A054 [Digital In4 Sel].
A054
09
Opto Common
–
For opto-coupled outputs. Electronically isolated with
opto outputs from analog I/O and digital inputs.
11
+24V DC
–
Referenced to Digital Common.
Drive supplied power for digital inputs.
Maximum output current is 100mA.
12
+10V DC
–
Referenced to Analog Common.
Drive supplied power for 0-10V external
potentiometer.
Maximum output current is 15mA.
13
±10V In (2)
Not Active
For external 0-10V (unipolar) or ±10V (bipolar) input P038,
supply (input impedance = 100k ohm) or
A051-A054,
potentiometer wiper.
A123, A132
14
Analog Common
–
For 0-10V In or 4-20mA In. Electronically isolated
with analog inputs and outputs from digital I/O and
opto outputs.
15
4-20mA In (2)
Not Active
For external 4-20mA input supply
(input impedance = 250 ohm).
16
Analog Output
OutFreq 0-10
The default analog output is 0-10V. To covert to a
A065, A066
current value, change the Analog Output Select DIP
Switch to 0-20mA. Program with A065 [Analog Out
Sel]. Max analog value can be scaled with A066
[Analog Out High].
Maximum Load: 4-20mA = 525 ohm (10.5V)
0-10V = 1k ohm (10mA)
17
Opto Output 1
MotorRunning
Program with A058 [Opto Out1 Sel]
A058, A059,
A064
18
Opto Output 2
At Frequency
Program with A061 [Opto Out2 Sel]
A061, A062,
A064
19
RS485 (DSI) Shield –
01
(1)
(2)
A055
P036 (1)
P038
P038,
A051-A054,
A132
Terminal should be connected to safety ground - PE
when using the RS485 (DSI) communications port.
See Footnotes (1) and (6) on page 11.
0-10V In and 4-20mA In are distinct input channels and may be connected simultaneously.
Inputs may be used independently for speed control or jointly when operating in PID mode.
English-13
Encoder Interface
The PowerFlex 40P Encoder Interface can source 5 or12 volt power and
accept 5, 12 or 24 volt single ended or differential inputs.
+V Cm B- B A- A
12V
5V
➊
Terminal Description
No. Signal
+V
5V-12V Power (1)
Cm Power Return
B-
Encoder B (NOT)
B
Encoder B
A-
Encoder A (NOT)
A
Encoder A
➊
Output
(1)
Description
Internal power source 250 mA (isolated).
Quadrature B input.
Single channel, pulse train, or quadrature A input.
DIP switch selects 12 or 5 volt power supplied at terminals “+V”
and “Cm” for the encoder.
When using 12V Encoder power, 24V I/O power, maximum output current at I/O
Terminal 11 is 50 mA.
Important: A quadrature encoder provides rotor speed and direction.
Therefore, the encoder must be wired such that the forward
direction matches the motor forward direction. If the drive
is reading encoder speed but the position regulator or other
encoder function is not working properly, remove power to
the drive and swap the A and B encoder channels or swap
any two motor leads. Drives using FRN 2.xx and greater
will fault when an encoder is incorrectly wired and E216
[Motor Fdbk Type] is set to option 5 “Quad Check”.
English-14
Prepare For Drive Start-Up
!
ATTENTION: Power must be applied to the drive to perform the
following start-up procedures. Some of the voltages present are at
incoming line potential. To avoid electric shock hazard or damage to
equipment, only qualified service personnel should perform the
following procedure. Thoroughly read and understand the procedure
before beginning. If an event does not occur while performing this
procedure, Do Not Proceed. Remove All Power including user
supplied control voltages. User supplied voltages may exist even when
main AC power is not applied to the drive. Correct the malfunction
before continuing.
Before Applying Power to the Drive
❏ 1. Confirm that all inputs are connected to the correct terminals and are
secure.
❏ 2. Verify that AC line power at the disconnect device is within the rated
value of the drive.
❏ 3. Verify that any digital control power is 24 volts.
❏ 4. Verify that the Sink (SNK)/Source (SRC) Setup DIP Switch is set to
match your control wiring scheme. See page 10 for location.
Important: The default control scheme is Source (SRC). The Stop
terminal is jumpered to allow starting from comms. If the
control scheme is changed to Sink (SNK), the jumper must
be removed from I/O Terminals 01 and 11 and installed
between I/O Terminals 01 and 04.
❏ 5. Verify that the Stop input is present or the drive will not start.
Important: If I/O Terminal 01 is used as a stop input, the jumper
between I/O Terminals 01 and 11 must be removed.
Applying Power to the Drive
❏ 6. Apply AC power and control voltages to the drive.
Start, Stop, Direction and Speed Control
Factory default parameter values allow the drive to be controlled from
comms. No programming is required to start, stop, change direction and
control speed directly from comms.
Important: To disable reverse operation, see A095 [Reverse Disable].
If a fault appears on power up, refer to page 19 for an explanation of the
fault code. For complete troubleshooting information, refer to the
PowerFlex 40P User Manual, Publication 22D-UM001 on the CD
supplied with the drive.
English-15
Display/Fault Reset
Menu
Description
Basic Display Group (View Only)
Commonly viewed drive operating
conditions.
RUN
REV
FAULT
Advanced Display Group (View Only)
Consists of advanced drive operating
conditions.
➋
➊
Fault Designator
Consists of list of codes for specific fault
conditions. Displayed only when fault is
present.
No. LED
➊ Run Status
LED State
Steady Red
Flashing Red
Direction Status Steady Red
Flashing Red
Fault Status
No. Key
Flashing Red
Name
Up Arrow
➋
Description
Indicates drive is running.
Drive has been commanded to change direction.
Indicates drive is running in reverse direction.
Drive has been commanded to change direction and motor is
decelerating to zero.
Indicates drive is faulted.
Description
Scroll: Press and release to scroll through user-selectable
Display Group and parameters.
Reset: Press and hold for three seconds to clear active fault.
Drive Programming Tools
For additional drive programming and control, a DSI remote HIM or PC
programming tools (DriveExplorer™ or DriveTools™ SP) should be used.
Description
Serial Converter Module
DriveExplorer Software(1)
DriveTools SP Software(1)
Remote Panel Mount, LCD Display
Remote Handheld, LCD Display
(1)
Catalog Number
22-SCM-232
9306-4EXP02ENE
9303-4DTS01ENE
22-HIM-C2S
22-HIM-A3
Requires a Serial Converter Module.
Set Parameter Display Option
E201 [LED Display Opt]
Selects which parameters can be viewed by the drive’s LED interface.
E201 Option
0
1
2
3
Values
Parameter Set
All Basic Display (Group b) and Advanced Display (Group d) parameters
All Basic Display Group (b001-b029) parameters
Basic Display Group parameters b001-b007 and b010
Basic Display Group parameter b001-b004
Default:
Min/Max:
Display:
2
0/3
1
English-16
Output Voltage
DC Bus Voltage
Drive Status
Fault 1 Code
Fault 2 Code
Fault 3 Code
Process Display
Control Source
b004
b005
b006
b007
b008
b009
b010
b012
Contrl In Status
Dig In Status
Comm Status
Control SW Ver
Drive Type
Elapsed Run Time
Testpoint Data
Analog In 0-10V
b013
b014
b015
b016
b017
b018
b019
b020
Analog In 4-20mA
Output Power
Output Powr Fctr
Drive Temp
Counter Status
Timer Status
Stp Logic Status
Torque Current
b021
b022
b023
b024
b025
b026
b028
b029
Basic Program Group
Motor NP Volts
Motor NP Hertz
Motor OL Current
P031
P032
P033
Minimum Freq
Maximum Freq
Start Source
Stop Mode
Speed Reference
P034
P035
P036
P037
P038
Accel Time 1
Decel Time 1
Reset To Defalts
Voltage Class
Motor OL Ret
P039
P040
P041
P042
P043
Advanced Program Group
Jog Frequency
Jog Accel/Decel
DC Brake Time
DC Brake Level
DB Resistor Sel
S Curve %
Boost Select
Start Boost
Break Voltage
Break Frequency
Maximum Voltage
Current Limit 1
Motor OL Select
PWM Frequency
Auto Rstrt Tries
Auto Rstrt Delay
Start At PowerUp
Reverse Disable
Flying Start En
Compensation
SW Current Trip
Process Factor
Fault Clear
Program Lock
Testpoint Sel
Comm Data Rate
Comm Node Addr
Comm Loss Action
Comm Loss Time
Comm Format
Language
A078
A079
A080
A081
A082
A083
A084
A085
A086
A087
A088
A089
A090
A091
A092
A093
A094
A095
A096
A097
A098
A099
A100
A101
A102
A103
A104
A105
A106
A107
A108
Anlg Out Setpt
Anlg In 0-10V Lo
Anlg In 0-10V Hi
Anlg In4-20mA Lo
Anlg In4-20mA Hi
Slip Hertz @ FLA
Process Time Lo
Process Time Hi
Bus Reg Mode
Current Limit 2
Skip Frequency
Skip Freq Band
Stall Fault Time
Analog In Loss
10V Bipolar Enbl
Var PWM Disable
Torque Perf Mode
Motor NP FLA
Autotune
IR Voltage Drop
Flux Current Ref
PID Trim Hi
PID Trim Lo
PID Ref Sel
PID Feedback Sel
PID Prop Gain
PID Integ Time
PID Diff Rate
PID Setpoint
PID Deadband
PID Preload
A109
A110
A111
A112
A113
A114
A115
A116
A117
A118
A119
A120
A121
A122
A123
A124
A125
A126
A127
A128
A129
A130
A131
A132
A133
A134
A135
A136
A137
A138
A139
Stp Logic 0
Stp Logic 1
Stp Logic 2
Stp Logic 3
Stp Logic 4
Stp Logic 5
Stp Logic 6
Stp Logic 7
Stp Logic Time 0
Stp Logic Time 1
Stp Logic Time 2
Stp Logic Time 3
Stp Logic Time 4
Stp Logic Time 5
Stp Logic Time 6
Stp Logic Time 7
EM Brk Off Delay
EM Brk On Delay
MOP Reset Sel
DB Threshold
A140
A141
A142
A143
A144
A145
A146
A147
A150
A151
A152
A153
A154
A155
A156
A157
A160
A161
A162
A163
Comm Write Mode
Power Loss Mode
Half Bus Enable
Max Traverse
Traverse Inc
Traverse Dec
P Jump
Sync Time
Speed Ratio
E207
E208
E209
E210
E211
E212
E213
E214
E215
Motor Fdbk Type
Motor NP Poles
Encoder PPR
Pulse In Scale
Ki Speed Loop
Kp Speed Loop
Positioning Mode
Find Home Freq
Find Home Dir
Encoder Pos Tol
Counts Per Unit
E216
E217
E218
E219
E220
E221
E222
E223
E224
E225
E226
Step Units 0
Step Units 1
Step Units 2
Step Units 3
Step Units 4
Step Units 5
Step Units 6
Step Units 7
Pos Reg Filter
Pos Reg Gain
Enh Control Word
Cmd Stat Select
E230
E232
E234
E236
E238
E240
E242
E244
E246
E247
E248
E249
Drive Status 2
Fibers Status
d301
d302
Slip Hz Meter
Speed Feedback
Encoder Speed
d303
d304
d306
Units Traveled H
Units Traveled L
d308
d309
Basic Display Group
Output Freq
Commanded Freq
Output Current
Digital In1 Sel
Digital In2 Sel
Digital In3 Sel
Digital In4 Sel
Relay Out Sel
Relay Out Level
Opto Out1 Sel
Opto Out1 Level
Opto Out2 Sel
Opto Out2 Level
Opto Out Logic
Analog Out Sel
Analog Out High
Accel Time 2
Decel Time 2
Internal Freq
Preset Freq 0
Preset Freq 1
Preset Freq 2
Preset Freq 3
Preset Freq 4
Preset Freq 5
Preset Freq 6
Preset Freq 7
b001
b002
b003
A051
A052
A053
A054
A055
A056
A058
A059
A061
A062
A064
A065
A066
A067
A068
A069
A070
A071
A072
A073
A074
A075
A076
A077
Enhanced Program Group
LED Display Opt
Digital Term 3
Accel Time 3
Decel Time 3
Accel Time 4
Decel Time 4
E201
E202
E203
E204
E205
E206
Advanced Display Group
English-17
Display Group Parameters
No.
Parameter
Min/Max
Display/Options
b001 [Output Freq]
0.00/[Maximum Freq]
0.01 Hz
b002 [Commanded Freq]
0.00/[Maximum Freq]
0.01 Hz
b003 [Output Current]
0.00/(Drive Amps × 2)
0.01 Amps
b004 [Output Voltage]
0/Drive Rated Volts
1 VAC
b005 [DC Bus Voltage]
Based on Drive Rating
1 VDC
b006 [Drive Status]
0/1 (1 = Condition True)
Bit 3
Decelerating
b007- [Fault x Code]
b009
F2/F122
F1
b010 [Process Display]
0.00/9999
0.01 – 1
b012 [Control Source]
0/112
Digit 2&3 = Speed Command
(See P038; 9 = “Jog Freq”)
b013 [Contrl In Status]
0/1 (1 = Input Present)
Bit 3
DB Trans On
Bit 2
Stop Input
Bit 1
Dir/REV In
Bit 0
Start/FWD In
b014 [Dig In Status]
0/1 (1 = Input Present)
Bit 3
Digital In 4
Bit 2
Digital In 3
Bit 1
Digital In 2
Bit 0
Digital In 1
b015 [Comm Status]
0/1 (1 = Condition True)
Bit 3
Comm Error
Bit 2
DSI Option
Bit 1
Transmitting
Bit 0
Receiving
b016 [Control SW Ver]
1.00/99.99
0.01
b017 [Drive Type]
1001/9999
1
b018 [Elapsed Run Time]
0/9999 Hrs
1 = 10 Hrs
b019 [Testpoint Data]
0/FFFF
1 Hex
b020 [Analog In 0-10V]
0.0/100.0%
0.1%
b021 [Analog In 4-20mA]
0.0/100.0%
0.1%
b022 [Output Power]
0.00/(Drive Power × 2)
0.01 kW
b023 [Output Powr Fctr]
0.0/180.0 deg
0.1 deg
b024 [Drive Temp]
0/120 degC
1 degC
b025 [Counter Status]
0/9999
1
b026 [Timer Status]
0.0/9999 Secs
0.1 Secs
b028 [Stp Logic Status]
0/8
1
b029 [Torque Current]
0.00/(Drive Amps × 2)
0.01 Amps
Bit 2
Accelerating
Bit 1
Forward
Bit 0
Running
Digit 1 = Start Command
(See P036; 9 = “Jog”)
Smart Start-Up with Basic Program Group Parameters
The PowerFlex 40P is designed so that start up is simple and efficient. The Program Group
contains the most commonly used parameters.
= Stop drive before changing this parameter.
No.
Display/Options
Default
P031 [Motor NP Volts]
20/Drive Rated Volts
Set to the motor nameplate rated volts.
Parameter
Min/Max
1 VAC
Based on Drive Rating
P032 [Motor NP Hertz]
15/500 Hz
Set to the motor nameplate rated frequency.
1 Hz
60 Hz
P033 [Motor OL Current] 0.0/(Drive Rated Amps×2) 0.1 Amps
Set to the maximum allowable motor current.
Based on Drive Rating
P034 [Minimum Freq]
0.00/500.0 Hz
Sets the lowest frequency the drive will output
continuously.
0.01 Hz
0.00 Hz
P035 [Maximum Freq]
0.00/500.0 Hz
Sets the highest frequency the drive will output.
0.01 Hz
60.00 Hz
P036 [Start Source]
1 = “3-Wire”
2 = “2-Wire”
3 = “2-W Lvl Sens”
4 = “2-W Hi Speed”
5 = “Comm Port”
6 = “Momt FWD/REV”
5
1/6
Sets the control scheme used to start the drive.
English-18
= Stop drive before changing this parameter.
No.
Parameter
Min/Max
Display/Options
0 = “Ramp, CF”(1)
1 = “Coast, CF”(1)
Active stop mode for all stop sources [e.g. run
2 = “DC Brake, CF”(1)
forward (I/O Terminal 02), run reverse (I/O
3 = “DCBrkAuto,CF”(1)
Terminal 03), RS485 port] except as noted.
4 = “Ramp”
Important: I/O Terminal 01 is always a coast to 5 = “Coast”
stop input except when P036 [Start Source] is set
6 = “DC Brake”
for “3-Wire” control. When in three wire control, I/O 7 = “DC BrakeAuto”
Terminal 01 is controlled by P037 [Stop Mode].
8 = “Ramp+EM B,CF”
9 = “Ramp+EM Brk”
(1)
Stop input also clears active fault.
P037 [Stop Mode]
0/9
P038 [Speed Reference]
1/9
Default
0
1 = “InternalFreq”
2 = “0-10V Input”
3 = “4-20mA Input”
4 = “Preset Freq”
5 = “Comm Port”
6 = “Stp Logic”
7 = “Anlg In Mult”
8 = “Encoder”
9 = “Positioning”
5
Sets the source of the speed reference to the
drive.
Important: When A051 or A052 [Digital Inx Sel] is
set to option 2, 4, 5, 6, 13 or 14 and the digital
input is active, A051, A052, A053 or A054 will
override the speed reference commanded by this
parameter. Refer to Chapter 1 of the PowerFlex
40P User Manual on CD for details.
P039 [Accel Time 1]
0.0/600.0 Secs
0.1 Secs
10.0 Secs
Sets the rate of accel for all speed increases.
P040 [Decel Time 1]
0.0/600.0 Secs
0.1 Secs
10.0 Secs
0 = “Ready/Idle”
1 = “Factory Rset”
0
2 = “Low Voltage” (480V)
3 = “High Voltage” (600V)
3
1 = “Enabled”
0 = “Disabled”
Sets the rate of decel for all speed decreases.
P041 [Reset To Defalts]
0/1
Resets all parameter values to factory defaults.
P042 [Voltage Class]
2/3
Sets the voltage class of 600V drives.
P043 [Motor OL Ret]
0/1
Enables/disables the Motor Overload Retention function.
Advanced Display Group Parameters
No.
Min/Max
Display/Options
d301 [Drive Status 2]
Parameter
0/1
1
d302 [Fibers Status]
0/1
1
d303 [Slip Hz Meter]
0.0/25.0 Hz
0.1 Hz
d304 [Speed Feedback]
0/64000 RPM
1 RPM
d305 [Speed Feedback F]
0.0/0.9
0.1
d306 [Encoder Speed]
0/64000
1
d307 [Encoder Speed F]
0.0/0.9
0.1
d308 [Units Traveled H]
0/64000
1
d309 [Units Traveled L]
0.00/0.99
0.01
Program Group Parameters
Refer to the PowerFlex 40P User Manual, Publication 22D-UM001 on
the CD supplied with the drive for complete listing of parameters.
English-19
Fault Codes
To clear a fault, press the Stop key, cycle power or set A100 [Fault Clear] to 1 or
2.
No.
Fault
Description
F2
Auxiliary Input(1)
F3
Power Loss
F4
F5
UnderVoltage(1)
OverVoltage(1)
F6
Motor Stalled(1)
F7
Motor Overload(1)
F8
Heatsink OvrTmp(1)
F12
HW OverCurrent
F13
F29
Ground Fault
Analog Input Loss(1)
F33
F38
F39
F40
F41
F42
F43
F48
Auto Rstrt Tries
Phase U to Gnd
Phase V to Gnd
Phase W to Gnd
Phase UV Short
Phase UW Short
Phase VW Short
Params Defaulted
Check remote wiring.
Verify communications programming for intentional fault.
Monitor the incoming AC line for low voltage or line power interruption.
Check input fuses.
Monitor the incoming AC line for low voltage or line power interruption.
Monitor the AC line for high line voltage or transient conditions. Bus overvoltage can also be
caused by motor regeneration. Extend the decel time or install dynamic brake option.
Increase [Accel Time x] or reduce load so drive output current does not exceed the current set
by parameter A089 [Current Limit].
An excessive motor load exists. Reduce load so drive output current does not exceed the
current set by parameter P033 [Motor OL Current]. Verify A084 [Boost Select] setting.
Check for blocked or dirty heat sink fins. Verify that ambient temperature has not exceeded 40°C
(104°F) for IP 30/NEMA 1/UL Type 1 installations or 50°C (122°F) for Open type installations.
Check fan.
Check programming. Check for excess load, improper DC boost setting, DC brake volts set too
high or other causes of excess current.
Check the motor and external wiring to the drive output terminals for a grounded condition.
An analog input is configured to fault on signal loss. A signal loss has occurred.
Check parameters. Check for broken/loose connections at inputs.
Correct the cause of the fault and manually clear.
Check the wiring between the drive and motor.
Check motor for grounded phase.
Replace drive if fault cannot be cleared.
Check the motor and drive output terminal wiring for a shorted condition.
Replace drive if fault cannot be cleared.
The drive was commanded to write default values to EEPROM.
Clear the fault or cycle power to the drive. Program the drive parameters as needed.
Check load requirements and A098 [SW Current Trip] setting.
F63 SW OverCurrent
F64 Drive Overload
Reduce load or extend Accel Time.
F70 Power Unit
Cycle power. Replace drive if fault cannot be cleared.
F71 Net Loss
The communication network has faulted.
Cycle power. Check communications cabling.
Check network adapter setting. Check external network status.
F80 SVC Autotune
The autotune function was either cancelled by the user of failed. Restart procedure.
F81 Comm Loss
If adapter was not intentionally disconnected, check wiring to the port. Replace wiring, port
expander, adapters or complete drive as required.
Check connection.
An adapter was intentionally disconnected. Turn off using A105 [Comm Loss Action].
Connecting I/O Terminal 04 to ground may improve noise immunity.
F91 Encoder Loss
Requires differential encoder. One of the 2 encoder channel signals is missing.
Check Wiring.
If P038 [Speed Reference] = 9 “Positioning” and E216 [Motor Fdbk Type] = 5 “Quad Check”
swap the Encoder channel inputs (see page 13) or swap any two motor leads.
Replace encoder.
F100 Parameter Checksum Restore factory defaults.
F111 Enable Hardware
DriveGuard Safe-Off Option (Series B) board is installed and the ENBL enable jumper has not
been removed.
Remove the ENBL enable jumper. Cycle power.
DriveGuard Safe-Off Option (Series B) board has failed.
Remove power to the drive. Replace DriveGuard Safe-Off Option (Series B) board.
Hardware Enable circuitry has failed.
Replace drive.
F122 I/O Board Fail
Cycle power. Replace drive if fault cannot be cleared.
(1)
(1)
Auto-Reset/Run type fault. Configure with parameters A092 and A093.
English-20
Drive Dimensions
PowerFlex 40P Frames – Ratings are in kW and (HP)
Frame
240V AC – 3-Phase
480V AC – 3-Phase
600V AC – 3-Phase
B
0.4 (0.5)
0.75 (1.0)
1.5 (2.0)
5.5 (7.5)
7.5 (10.0)
0.4 (0.5)
0.75 (1.0)
1.5 (2.0)
5.5 (7.5)
7.5 (10.0)
0.75 (1.0)
1.5 (2.0)
2.2 (3.0)
5.5 (7.5)
7.5 (10.0)
C
2.2 (3.0)
3.7 (5.0)
2.2 (3.0)
4.0 (5.0)
11.0 (15.0)
4.0 (5.0)
11.0 (15.0)
PowerFlex 40P AC Drive
Dimensions are in millimeters and (inches).
Weights are in kilograms and (pounds).
F
RUN
REV
FAULT
E
Frame
C
D
G
20A-DG01
A
A
B 100
(3.94)
C 130
(5.1)
B
Ship
Weight
B
C
D
E
F
G
180
(7.09)
260
(10.2)
148
(5.83)
192
(7.56)
87
(3.43)
116
(4.57)
168
(6.61)
246
(9.7)
136 87.4
(5.35) (3.44)
180 –
(7.1)
2.2
(4.9)
4.3
(9.5)
5.5 (0.22)
Communication, RFI Filter, IP 30/NEMA 1/UL Type 1 Option Kits
B
A
∅ 28.5
(1.12)
107.0 (4.21)
66.0 (2.60)
24.0 (0.94)
79.1 (3.11)
64.1 (2.52)
40.6 (1.60)
25.6 (1.01)
∅ 22.2
(0.87)
∅ 22.2
(0.87)
152.2
(5.99)
C
109.9
(4.33)
111.2
(4.38)
74.3
(2.93)
B Frame - 22-JBAB
C Frame - 22-JBAC
108.7 (4.28)
92.2 (3.63)
69.2 (2.72)
45.7 (1.80)
D
77.5 (3.05)
Dimension
50.0 (1.97)
A
B
C
D
22.5 (0.89)
Option
Comm Cover
EMC Line Filter
EMC Line Filter
IP30/NEMA 1/UL
Type 1
IP30/NEMA 1/UL
Type 1 for Comm
Cover
∅ 28.5
(1.12)
22.2 (0.87)
∅ 22.2
(0.87)
∅ 22.2
(0.87)
B Frame C Frame
Drive
Drive
25 (0.98)
50 (1.97)
229 (9.02)
33 (1.30)
25 (0.98)
60 (2.36)
309 (12.17)
60 (2.36)
64 (2.52)
60 (2.36)
179.8
(7.08)
134.3
(5.29)
144.8
(5.70)
105.3
(4.15)
109.8
(4.32)
76.3
(3.00)
B Frame - 22-JBCB
C Frame - 22-JBCC
(used with Comm Cover)
(used with Comm Cover)
U.S. Allen-Bradley Drives Technical Support
Tel: (1) 262.512.8176, Fax: (1) 262.512.2222, Email: [email protected], Online: www.ab.com/support/abdrives
Publication 22D-QS001B-EN-P – May 2007
Supersedes March 2006
Copyright © 2007 Rockwell Automation, Inc. All rights reserved.
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertisement