HPD400 user`s manual
4CH Digital Video Recorder
User’s Manual
This user’s manual is subject to change without any previous notice by
function upgrade or addition.
Version_1.2
May, ‘2005
SAFETY PRECAUTIONS
CAUTION
RISK OF ELECTRIC SHOCK DO NOT OPEN
CAUTION: TO REDUCE THE RISK OF ELECTRIC SHOCK, DO NOT REMOVE COVER (OR BACK)
NO USER-SERVICEABLE PARTS INSIDE. REFER SERVICING TO QUALIFIED SERVICE
PERSONNEL.
This label may appear on the rear of the unit due to space limitations.
The lightning flash with arrow point symbol, within an equilateral triangle, is
intended to alert the user to the presence of uninsulated “dangerous voltage”
within the product’s enclosure that may be of sufficient magnitude to
constitute a risk of electric shock to persons.
The exclamation point within an equilateral triangle is intended to alert the
user to the presence of importance operating and maintenance (servicing)
instructions in the literature accompanying the appliance.
Warning
To reduce the risk of fire or electric shock, Do not expose this product to rain or moisture.
Do not insert any metallic object through ventilation grills.
Power disconnect : Units with or without ON-OFF switches have power
supplied to the unit whenever the power cord is inserted into the main source;
However, the unit is operational only when the ON-OFF switch is in the ON
position. To disconnect it from the main source, you have to disconnect the
Power cord.
FCC COMPLIANCE STATEMENT
A CLASS A computing device subject to certification by the Commission shall be identified pursuant to
Par 2.925 et Seq of the chapter. In addition, the label shall include the following statement:
This device complies with Part 15 of FCC Rules.
Operation is subject to the following two conditions:
(1)This device may not cause harmful interference, and
(2)This device must accept any interference received,
including interference that may cause undesired operation.
Where a device is constructed in two or more sections connected by wires and marked together, the
statement specified in this Section is required to be affixed only to the main control unit.
The users manual or instruction manual for the EUT shall contain the following statement or equivalent.
Caution : Changes or Modifications not expressly approved by the party responsible for compliance could
void the users authority to operate the equipment.
If the EUT requires accessories such as special shield cables and/or connectors to enable compliance
with emission limits, the instruction manual for the EUT shall include appropriate instruction on the first
page of the text concerned with the installation of the device that these special accessories must be used
with the device. It is the responsibility of the user to use the needed special accessories supplied with the
equipment.
For a CLASS A digital device or peripheral, the instruction furnished the user shall include the following or
Similar statement placed in a prominent location in the text of the manual.
Note : This equipment has been tested and found to comply with the limits for a CLASS a digital device,
pursuant to Part 15 of FCC Rules. These limits are designed to provide reasonable protection against
harmful interference when the equipment is operated in a commercial environment, This equipment
Generates, uses and can radiate radio frequency energy and, if not in stalled and used in accordance
with the instruction manual, may cause harmful interference to radio communications. Operation of the
this equipment in a residential area is likely to cause harmful interference in which cause the user will
be required to correct the interference at his own expense.
Before Starting Your DVR Operation
This document is a basic manual for the SIGNALSYNC DVR users.
This manual describes the appearance and name of products, how to configure the
system program, and how to use the system.
Before using SIGNALSYNC DVR, a user should read the contents of user manual, and
then deal with the product considering the precautions defined in the manual.
To open the system case and touch the inner parts for corrective maintenance, a user
should contact the place where he/she purchased the products to get the help from
expert.
In addition, if there is any question for use or any damage on the product, please contact
call the place where he/she purchased the products.
Precautions for safety (User should observe)
1. Precautions for installation
z
Install the product on a flat floor not closed and retain the distance of more than 15
cm from the rear panel to the wall.
z
Install the product on a well-ventilated place.
z
Keep it away from strong magnetism or electromagnetic wave.
z
Installing it near radio equipment such as TV and radio may cause a fault.
z
Do not install it on a place that is exposed directly to the sun or contains lots of heat
such as near a heating apparatus.
z
Do not install it on a cold place.
z
Place the equipment or tools in the site remote from a busy road so that people are
not hurt.
z
Do not install it on a place where there is severe vibration, much humidity or soot.
z
Should use the product in the rated voltage (The equipment is used as both 110V
and 220V, but it is set to 220V for delivery. It is possible to adjust it with the
changeover switch on the rear panel.)
z
Connect it to the outlet with the ground terminal.
z
Discard the vinyl bag well. (It is dangerous to put it on the head.)
2. Precautions for use
z
For the repair, contact the company or the place where you purchased the product.
z
Read the user manual before using the product.
z
Do not open the cover at your discretion because there are parts sensitive to the
environment within the equipment.
z
Arrange the power cord safely and do not touch it with wet hands.
z
Do not use a loose outlet or a damaged power cable.
z
Do not use benzene, thinner and alcohol for cleaning. They may deform the product.
z
Do not touch the exposed terminal.
z
For the power-off of system, normally turn off the power of the program and then,
power off the peripherals. (Do not power it off with the power button on the front panel
of body.)
z
Be careful to prevent a conductive object from falling into a hole that was punched for
ventilation.
z
Do not dissemble and remodel the product.
z
Do not place a heavy thing on the body.
z
Do not give a shock during the movement of equipment.
z
If you use the product in the state of smoke or smell emitted, it may cause a fire or an
electric shock. For this case, immediately block the power switch and contact the
company or the place where you purchased the product to consult it with a special
technician.
This user’s manual is subject to change without any notice by function upgrade and
so on.
Table of Contents
I. Introduction
1. Package Contents
2. Features
3. Front Panel and Rear Panel Connection
II. Installation
1. Front Panel
2. Rear Panel
3. Remote Controller (Optional)
4. Menu Tree
III. Main MENU Programming
1. Overview Main Menu
2. SYSTEM SETUP
3. DISPLAY SETUP
4. RECORDING SETUP
5. ALARM SETUP
6. MOTION SETUP
7. WEEKLY SETUP
8. NETWORK SETUP
9. ARCHIVING
10. HDD INFORMATION
11. SEARCH LIST
12. DISPLAY Mode
13. RECORDING Mode
14. PLAYBACK Mode
IV. Software Upgrade Procedure
APPENDIX 1. Specification
2. Pin Description of connectors
I.
Introduction
1. Package Content
When purchasing SIGNALSYNC product, unpack it at first and unload it on a flat
floor or a place where it is to be located. Then, verify that the following contents are
contained.
z
z
z
z
z
z
4CH DVR
Power code
Rack Mount Bracket
User’s manual
Install CD
Remote controller (Optional)
4CH DVR
User’s
Manual
Power Code
Rack Mount Bracket User’s Manual
Install CD
Remote controller
(Optional)
2. Features
This DVR provides recording capabilities for four camera inputs. It provides playback
or live display and network function while in recording mode. And also it offers the
following features:
‹ 4 Composite Input Connectors/ 4 Loop-Through Video Connectors
- Compatible with Color (NTSC or PAL) and B&W (CCIR and EIA-170) Video
‹ Display and Record Video Resolution
- NTSC (720x480), PAL (720x576)
- Single, QUAD, Sequential Image Display
- 4CH multiplexing video recording with 720x480 resolution (NTSC)
‹ Compression: M-JPEG
- Standard image, high quality; 16KB / field
‹ Multiple Search Engines (Date/Time, Event)
‹ Records up to 60 NTSC IPS (50 PAL Images per Second)
‹ Continuous Recording in Disk Overwrite Mode
‹ Simultaneously Record, Playback and Network
‹ Archiving using USB Memory Drive
- USB 1.1 Storage Class support
‹ User-friendly Graphical User Interface (GUI)
‹ Manual/ Schedule and alarm/ motion recording Modes (Time and Event)
‹ Alarm input Connections, relay output connection
‹ Network Function
- Dynamic IP (DHCP, Floating IP) support
- Live or Recorded Video Access via Ethernet
- Remote configuration
- DDNS Client support
‹ Audio Recording and Playback
- 1ch audio support
3. Front Panel and Rear Panel Connection
USB Memory
Remote Controller
Drive
Audio
Input
Cameras
RS485
(RTZ Camera)
Power
Code
Audio
Alarm
Output
RS232C
Out
Monitor
LAN
(Ethernet)
Sensor
Input
II. INSTALLATION
Front Panel
1
2
3
4
5
6
7
8
9
10
11 12
1. USB port
A USB port is provided to connect external USB memory drive for archiving video.
2. Archiving button
Whenever ARCHIVE button is pressed, archiving will be started.
3. REC/ STOP button
Press REC (Red circle) to begin record. Press REC to stop recording again. This is
toggle button.
4. PLAY/ STOP button (▶)
If PLAY/ STOP is pressed, search lists will be displayed to begin playback. After
selecting one recorded file, playback will be started by PLAY/ STOP button. To
stop playback, PLAY/ STOP button is used. This is toggle button. While it is in high
speed playback mode like FF or REW, it return to playback by PLAY/ STOP button.
5. FF (▶▶)
Press FF to perform high speed forward playback. It support 2 to 32 times playback
speed.
6. REW (◀◀)
Press REW to perform high speed backward playback. It support 2 to 16 times
playback speed.
7. PAUSE
Press PAUSE to pause playback.
8. MENU/ ESC
Press MENU/ESC button to enter menu system. Also MENU/ESC is used to escape
upper menu and to save set-up parameter at the same time .
9. QUAD/ SEQ
This button is used for QUAD, sequential display. It is rotated as QUADÎ Sequential
Î QUAD.
10. LEDs for Power ON, Archiving, Network Indication
1) Power On indicator
Indicates power is ON when power LED is lit.
2) Network indicator
Indicates data transmission via network is performed when network LED is lit.
3) Archiving indicator: Indicates archiving has been doing when archiving LED is lit.
4) Remote controller sensor input window
11. Direction (Number) buttons
It is consists of UP(1), RIGHT(2), DOWN(3), LEFT(4) buttons.
NOTE: These buttons is used in numbering input for password , in left/ right movement
and increasing/ decreasing parameter for MENU.
12. ENTER button
Press ENTER button to confirm a selection.
Rear Panel
2
1
3
4
5
6
7
8
9
10
11
1. 75 Ohm Termination Switch
If you want to connect loop-through video outputs into another video equipments,
75 Ohm termination switch should be “OFF”. Then, another video equipments should
be 75 ohm terminated.
If loop through video outputs are not connected to another video equipments, it should
be “ON”.
If 75 Ohm termination switch “ON” or “OFF” is changed, it will cause poor video quality.
2. 4CH Video Input: 4 channel composite video inputs with BNC connectors
Since this DVR automatically detects video format (NTSC or PAL) as soon as power is
ON, NTSC or PAL video sources can be connected. But NTSC and PAL video sources
for 4CH video inputs can not be mixed. If they are mixed, DVR can’ not be operated
properly.
3. 4CH Loop through outputs: 4 channel composite video outputs with BNC connectors
If the connection of loop-through video outputs into another video equipments is
requested, 4CH Loop-Through outputs can be utilized for it. If loop-through video
outputs will be connected to another video equipments, 75 Ohm termination switch
should be “OFF”. Then, another video equipments should be 75 ohm terminated.
4. Video Output 1: composite video output
Connect this video output to monitor so that live, playback pictures would be monitored.
5. Audio Input, Audio Output: Unbalanced audio signal input with RCA jack
This DVR can record audio. Connect the audio source to audio input. Connect audio
output to your amplifier because the DVR does not have amplified audio output, so you
will need a speaker with an amplifier. The audio input can be from an amplified source
or directly from a microphone.
6. Ethernet Port: RJ45 jack
Connect a Cat5 cable with an RJ-45 jack to the DVR connector. Remote PC viewer
software via network enable you to live viewing or searching.
7. RS232C serial port
An RS232 port is provided to connect other external equipments. Use DB-9S (female)
connector to connect to the DVR.
8. RS485: For camera pan and tilting control
This DVR can be controlled remotely by remote PC software. The RS485 connector
can be used to control PTZ (pan, tilt, zoom) cameras. Connect RX+, RX- of the
control system to the TX+, TX- (respectively) of the DVR.
9. Alarm input and relay output: 4 alarm inputs and 1 relay output with NO, NC
To make secure connections on the Alarm Connector Strip, press and hold the button
and insert the wire in the hole below the button. After releasing the button, tug gently
on the wire to make certain it is connected. To disconnect a wire, press and hold the
button above the wire and pull out the wire.
4 Alarm Inputs: 1,2,3,4,G(Ground)
You can use external devices to signal the DVR to react to events. Mechanical or
electrical switches can be wired to the Alarm Inputs and GND (Ground) connectors.
The threshold voltage is 4.3V and should be stable at least 0.5 seconds to be detected.
G (Ground), COM (common): G is same as common.
Connect the ground side of the Alarm input to G (Ground). Connect the ground side of
relay output to COM connector.
Relay output:
The DVR support NO, NC relay output at the same time. You can select NO or NC
, according to characteristic of mechanical or electrical switch.
10. FAN for cooling
11. AC outlet
Connect the power cord to the DVR and then to the wall outlet (100-240V AC).
Remote Controller (Optional)
< Remote Controller buttons >
< Button Description >
No
1
2
3
4
Description
Button Name
1
Recording Start/ Stop button
REC
2
Button LOCK Enable/Disable
LOCK
3
Archiving Start button
USB
4
Video CH selection buttons
1,2,3,…,0, +10
5
1) Sequential display button
2) QUAD display button
3) 9 picture display button
4) 16/ 8/ 10 picture display
button
Video Picture
Display mode
6
Main picture selection button
in 8. 10 picture display mode
Function
7
Movement to upper menu
ESC
8
Movement to menu mode
MENU
9
1) UP (▲)
2) DOWN (▼)
3) LEFT (◀)
4) RIGHT (▶)
5) ENTER
Direction
(Password
Number Input)
and
ENTER buttons
10
Playback Stop button
STOP
11
Playback Start button
Search/ PLAY
12
PAUSE/ 1 field movement
backward.
PAUSE/ 1 field movement
forward.
Movement
forward or
backward
by 1 Field.
13
Fast Playback buttons
FF, REW
5
6
7
8
9
10
11
12
13
Menu Tree
MAIN MENU
1
SYSTEM SETUP
1
LANGUAGE
2
DISPLAY SETUP
3
RECORDING SETUP
4
ALARM SETUP
5
MOTION SETUP
6
WEEKLY SCHEDULE
7
NETWORK SETUP
2
3
4
5
6
7
8
9
VIDEO FORMAT
PASSWORD
ADMIN LOCK
TIME FORMAT
DATE FORMAT
DATE/TIME SET
DEFAULT
REV STATUS
8
ARCHIVING
9
HDD INFORMATION
ALARM SETUP
1
FRAME RATE
2
3
4
5
DURATION
SENSOR TYPE
TRIGGER OUT
BUZZER ALERT
START
DURATION
SUN
00: 00
00: 00
MON
TUE
WED
THU
FRI
SAT
00: 00
00: 00
00: 00
00: 00
00: 00
00: 00
00: 00
00: 00
00: 00
00: 00
00: 00
00: 00
HOLIDAY
NONE
NONE
1
ADJUST CHANNEL
2
3
4
5
6
7
BRIGHTNESS
CONTRAST
PTZ TYPE
SEQ DWELL TIME
TIME/DATE OSD
CAM NUMBER OSD
VIDEO LOSS OSD
POP-UP DISPLAY
POSITION
RECORDING SETUP
1
QUALITY
2
3
4
FRAME RATE
AUDIO
STOP KEY
NETWORK SETUP
WEEKLY SCHEDULE
WEEK
DISPLAY SETUP
SYSTEM SETUP
1
CONNECT
2
3
4
5
6
7
8
9
IP ADD
SUB NET
GATE WAY
DNS
PORT
NTP TIME
TIME ZONE
DDNS STATUS
MOTION SETUP
1
SENSITIVITY
2
FRAME RATE
3
DURATION
4
CAM1
5
CAM2
6
CAM3
7
CAM4
8
BUZZER ALERT
HDD INFORMATION
ARCHIVING
1
ARCHIVING TYPE
2
3
ARCHIVING TIME
ARCHIVE INFO
NAME: / TOTAL:
ARCHIVE LOG
4
1
HARD DISK
2
3
TOTAL
FREE
FORMAT HDD
OVERWRITE
III. Main Menu Programming
1. Overview Main Menu
Before using your DVR for the first time, you will want to establish the initial settings.
This includes items such as time and date, password, display, record mode, network
and so on.
In order to program Main Menu, first press MENU/ESC button of front panel in DVR.
If ADMIN LOCK is set as YES (factory default is YES), below figure will be appeared.
PASSWORD LOGIN
Then input password number using UP(1),
RIGHT(2), DOWN(3), LEFT(4) Buttons
(Factory default number is 1111), and
press ENTER button. MAIN MENU will be
appeared.
PASSWORD
****
ENTER
▲ ▼ ◀ ▶ EXIT
NOTE:
To access the DVR Main Menu, press MENU/ESC. To escape MENU, MENU/ESC
button is also used. Buttons for movement in Menu are ◀(4), ▶(2). Button for selection
is ENTER, Buttons for increasing or decreasing parameter are ▲(1), ▼(3). Press
MENU/ESC to return to the previous MENU after setting and to save the values of
setup.
Í ◀(LEFT & 4), ▶(RIGHT & 2), ▲(UP & 1), ▼(DOWN & 3) and ENTER
buttons.
MAIN MENU
< MAIN MENU >
1
SYSTEM SETUP
2
DISPLAY SETUP
3
RECORDING SETUP
4
ALARM SETUP
5
MOTION SETUP
6
WEEKLY SCHEDULE
7
NETWORK SETUP
8
ARCHIVING
9
HDD INFORMATION
ENTER
▲ ▼ ◀ ▶ EXIT
2. SYSTEM SETUP
To access SYSTEM SETUP, press ENTER button after moving highlight bar to
SYSTEM SETUP in MAIN MENU. Below menu will appear on monitor.
1
SYSTEM SETUP
1
LANGUAGE
: ENG/CHN
2
VIDEO FORMAT
: NTSC
3
PASSWORD
: ****
4
ADMIN LOCK
: YES
5
TIME FORMAT
: 24HOURS
6
DATE FORMAT
: MM-DD-YY
7
DATE/TIME SET
:
05: 20: 2005
10:50:11
8
DEFAULT
: YES / NO
9
REV STATUS
: VERSION
1:1:2
ENTER
▲ ▼ ◀ ▶ EXIT
1) LANGUAGE : Language Selection
The languages supported are English, Chinese, Japanese.
2) VIDEO FORMAT: NTSC/ PAL
Video format is automatically detected after power ON. The detected video information
will be displayed on VIDEO FORMAT. User don’t need to change video format.
3) PASSWORD:
Move Highlight bar to PASSWORD in the SYSTEM Menu using DOWN or UP button .
And then press ENTER to change password. For four digit password input, UP,
RIGHT, DOWN and LEFT buttons can be used.
NOTE: Factory Default is “Pressing UP button four times”.
SYSTEM SETUP
2
PASSWORD
****
OLD
Input old password. (Factory Default is 1111)
****
NEW
Input new password. Enter the password by
pressing the appropriate combination of four
number, UP(1), RIGHT(2), DOWN(3),
LEFT(4) buttons.
****
AGN
Input new password again to confirm new
password.
SYSTEM SETUP
2
PASSWORD
SYSTEM SETUP
2
PASSWORD
4) ADMIN LOCK: YES/ NO
Move Highlight bar to ADMIN LOCK in the SYSTEM Menu using DOWN or UP button .
If ADMIN LOCK is selected as YES by LEFT or RIGHT, password is requested
whenever entering menu. If NO, password isn’t requested.
5) TIME FORMAT: 24/ 12 HOURS
Move Highlight bar to TIME FORMAT in the SYSTEM Menu using DOWN or UP button
and press the LEFT or RIGHT button to select 24 HOURS (military time) or 12 HOURS
(AM/PM). Whenever Time Format is changed, clock information on monitor and file
information in search list will be changed together.
6) DATE FORMAT: MM-DD-YY/ DD-MM-YY/ MM-DD-YY
Move Highlight bar to DATE FORMAT in the SYSTEM Menu using DOWN or UP
button. Date format can be changed using LEFT or RIGHT button.
7) DATE/ TIME SET:
Move Highlight bar to DATE/TIME SET in the SYSTEM Menu using DOWN or UP
button. And then press ENTER to set the time.
NOTE:
1. If you set a date and time that is older than some of your recorded
images, it is not easy to manage recorded files.
2. Before starting your DVR, DATE/ TIME should be setting properly.
SYSTEM SETUP
6
DATE/TIME SET
Year is changed by DOWN or UP button.
2004:01:11 10:50:11
By LEFT or RIGHT button.
SYSTEM SETUP
6
DATE/TIME SET
2004:01:11 10:50:11
Month is changed by DOWN or UP button.
LEFT or RIGHT button.
SYSTEM SETUP
6
DATE/TIME SET
2004:01:11 10:50:11
Date is changed by DOWN or UP button.
…
LEFT or RIGHT button.
SYSTEM SETUP
6
DATE/TIME SET
2004:01:11 10:50:11
Time is changed by DOWN or UP button.
To confirm DATE/TIME setting, ENTER
button should be pressed.
After setting DATE/ TIME, ESC or ENTER button can be used in order to return upper
Menu.
8) DEFAULT: Return to factory default mode.
9)REVISION STATUS
It shows DVR software version. Whenever upgrading software, upgraded version will
be displayed.
3. DISPLAY SETUP
2
DISPLAY SETUP
1
ADJUST CHANNEL
CH1, CH2, CH3, CH4
BRIGHTNESS
1-99 %
CONTRAST
1-99 %
PTZ TYPE
2
SEQ DWELL TIME
NONE, 1-60 SEC
3
TIME/ DATE OSD
ON/ OFF
4
CAM NUMBER OSD
ON/ OFF
5
VIDEO LOSS OSD
ON/ OFF
6
POP-UP DISPLAY
ON/ OFF
7
POSITION
ENTER
▲ ▼ ◀ ▶ EXIT
To access DISPLAY SETUP, press ENTER button after moving highlight bar to
DISPLAY SETUP in MAIN MENU. Above menu will appear on monitor.
1) ADJUST CHANNEL: CH1, CH2, CH3, CH4
The camera channel to adjust brightness, contrast can be selected by ADJUST
CHANNEL using LEFT or RIGHT button.
BRIGHTNESS: 1 to 99 %
BRIGHTNESS can be changed using LEFT or RIGHT button.
- NOTE: Minimum value is 1 (very dark), maximum value is 99 (very bright).
CONTRAST: 1 to 99 %
CONTRAST can be changed using LEFT or RIGHT button.
PTZ TYPE (Pan, Tilt and zooming protocol selection)
The high end camera(s) with panning, tilting and zooming function would be
connected with some of video inputs. The camera(s) has(have) its own control
protocol to control panning, tilting and zooming, according to PTZ camera
manufacturer.
In order to control PTZ of the camera from remote area by network viewer software,
proper PTZ TYPE should be selected in here. Your DVR supports over ten PTZ
cameras. According to customer requirements, PTZ control will be added in it.
* NOTE: PTZ stands for pan, tilt and zooming.
* PTZ protocols: Panasonic/ Pelco-D/ PelcoP/ Techwin/ Niko/ DRX502A_DSC230s
/KRE_301_302/ GC_755_NP/ TOA_CC554/ RAS716LS and so on.
2) SEQ DEWLL TIME: NONE/ 1 to 60 seconds.
SEQ DWELL TIME can be changed using LEFT or RIGHT button.
- NOTE: It is just reflected in sequential display mode.
3) TIME/DATE OSD: ON/ OFF
When it is set as OFF, characters which indicates time/ date will be disappeared on
monitor. But time and date information still are added into recording files.
4) CAM NUMBER OSD: ON/ OFF
When it is set as OFF, characters which indicates camera number will be disappeared
on monitor.
5) VIDEO LOSS OSD: ON/ OFF
When it is set as OFF, black pictures will be displayed in the cameo with video loss.
When it is set as ON, “VIDEO LOSS” character with white color will be displayed in blue
screen.
6) POP-UP DISPLAY: ON/ OFF
When it is set as OFF, pop-up image of camera which motion detection or alarm triggering
is occurred will not displayed. When it is set as ON, the channel (s) which motion is (are)
detected or external alarm is (are) triggered will be POP-UP in monitor during maximum 30
seconds. In case that motion detection or alarm event is occurred more than two channels,
POP-UP picture will be appeared in monitor turn by turn during 3 seconds for each
channels. Total period of POP-UP display is 30 seconds.
7) POSITION: According to monitor, even same Video signal can be displayed on different
position of monitor by the deflection characteristic of it. In this case, vertical and horizontal
display position can be adjusted by “VERTICAL” and
POSITION
“HORIZONTAL” of POSITION.
1
VERTICAL
: 52
2
HORIZONTAL
: 205
3
DEFAULT
: NO
4. RECORDING SETUP
3
RECORDING SETUP
1
QUALITY
: HIGH
2
FRAME RATE
: 60/ IPS
3
AUDIO
: OFF
4
STOP KEY
: DISABLE
ENTER
▲ ▼ ◀ ▶ EXIT
To access RECORDING SETUP, press ENTER when RECORDING SETUP in MAIN
MENU using DOWN or UP is highlighted with blue color. The menu above will
appear on monitor.
1) QUALITY: LOW, STANDARD, STANDARD PLUS, HIGH
Your DVR support four recording quality from low to high. It can be selected using
LEFT or RIGHT button.
2) FRAME RATE: 60, 30, 15, 10, 5, 1, 0.5 IPS.(NTSC)
Your DVR support several frame rates from 0.5 to 60 Image per seconds for NTSC
from 0.5 to 50 IPS for PAL. It can be selected using LEFT or RIGHT button.
NOTE: when your DVR is in recording mode, some of parameters related to
RECORDING can’t be changed.
3) AUDIO: ON/ OFF
Your DVR can select whether to record audio signal with video signal together or not.
It can be selected using LEFT or RIGHT button.
4) STOP KEY: DISABLE/ ENABLE
In case of manual recording, manual recording is started and stop by the REC/ STOP
button
. This STOP KEY ENABLE can protect the “recording stop” which is not
intended.
NOTE: While your DVR is on recording mode, it doesn’t support the setup
related to the recording including recording quality, frame rate, audio
ON/ OFF and date/ time setup in SYSTEM SETUP.
5. ALARM SETUP
4
ALARM SETUP
1
FRAME RATE
: 60/ IPS
2
DURATION
: 3 MIN
3
SENSOR TYPE
: NONE/ N.O/ N.C
4
TRIGGER OUT
: DISABLE
5
BUZZER ALERT
: DISABLE
ENTER
▲ ▼ ◀ ▶ EXIT
To access ALARM SETUP, press ENTER when ALARM SETUP in MAIN MENU using
DOWN or UP is highlighted with blue color. The menu above will appear on monitor.
1) FRAME RATE: 60, 30, 15, 10, 5, 1, 0.5 IPS.(NTSC)
Your DVR support several frame rates from 0.5 to 60 Image per seconds for NTSC
from 0.5 to 50 IPS for PAL. It can be selected using LEFT or RIGHT button.
2) DURATION:
It define recording duration after motion is detected. This DVR support 10 sec, 30 sec,
1,2,3,4,5,6,7,8,9,10,20,30,40,50,60 minutes. It can be selected using LEFT or RIGHT
button.
3) SENSOR TYPE: NONE/ N.O/ N.C
Your DVR can select the input type for external alarm inputs which usually has normal
open or normal close using LEFT or RIGHT button.
4) TRIGGER OUT (Relay Output): DISABLE/ ENABLE
Your DVR support both dry open and dry contact through different relay output port.
It can be selected using LEFT or RIGHT button.
5) BUZZER ALERT: DISABLE/ ENABLE
If external alarm sensor(s) be triggered, beep sound from buzzer by BUZZER ALERT
with ENABLE would be occurred during two seconds.
6. MOTION SETUP
5
MOTION SETUP
1
SENSITIVITY
: normal
2
FRAME RATE
: 60/ IPS
3
DURATION
: 1 MIN
4
CAM1
: DISABLE
5
CAM2
: DISABLE
6
CAM3
: DISABLE
7
CAM4
: DISABLE
8
BUZZER ALERT
: DISABLE
ENTER
▲ ▼ ◀ ▶ EXIT
Your DVR has built-in video motion detection function. Motion detection Enable/ Disable,
motion area can be selected separately for each camera. When your DVR detects
motion, it begin to record multiplexed video signals from the camera or cameras which
motion is detected and display only the camera with motion during 30 seconds.
Recoding duration can be selected in MOTION SETUP menu. To access MOTION
SETUP, press ENTER when MOTION SETUP in MAIN MENU using DOWN or UP
button is highlighted with blue color. The menu above will appear on monitor.
1) SENSITIVITY: 5 steps (very low, low , normal, high, very high)
Your DVR support 5 sensitivity levels. It can be selected using LEFT or RIGHT button.
2) FRAME RATE:
Your DVR support 60, 30, 15, 10, 5, 1, 0.5 IPS for NTSC. 50, 25,16, 10, 5, 1, 0.5 IPS
for PAL. It can be selected using LEFT or RIGHT button.
3) DURATION:
It define recording duration after motion is detected. This DVR support 10 sec, 30sec,
1,2,3,4,5,6,7,8,9,10,20,30,40,50,60 minutes. It can be selected using LEFT or RIGHT
button.
4) CAM1, CAM2, CAM3, CAM4: DISABLE/ ALL/ SETUP
Motion Enable/Disable, Motion zone can be selected separately for each of four
cameras.
DISABLE means that function of motion detection isn’t utilized.
ALL means that entire image area is selected for motion detection.
SETUP can be selected in order to select given image area which want to monitor
motion detection. Total motion area consists of 14x10 blocks. To select arbitrary motion
zone, select SETUP using LEFT or RIGHT button. And then press ENTER button to
designate motion areas in 14x10 blocks. You can use LEFT or RIGHT button for
horizontal movement UP or DOWN button for vertical movement, ENTER button for
selection. You can define the area of the image where you don’t want to detect motion.
Selected blocks in 14x10 blocks will be blinking. To remove previously defined image
block for motion detection, press ENTER button again at that block. After defining
motion zone, press MENU/ESC button to return upper Menu. Motion detection zone is
the area which edge of the motion blocks is not flickering.
< The example of motion area setup >
5) BUZZER ALERT: DISABLE/ ENABLE
If motion be detected in motion area, beep sound from buzzer by BUZZER ALERT
with ENABLE would be occurred during two seconds.
7. WEEKLY SCHEDULE
6
WEEKLY SCHEDULE
WEEK
START
DURATION
SUN
00: 00
00: 00
OFF
MON
00: 00
00: 00
OFF
TUE
00: 00
00: 00
OFF
WED
00: 00
00: 00
OFF
THU
00: 00
00: 00
OFF
FRI
00: 00
00: 00
OFF
SAT
00: 00
00: 00
OFF
HOLIDAY
NONE
NONE
OFF
▲ ▼ ◀ ▶ EXIT
ENTER
To setup WEEKLY SCHEDULE, press ENTER when WEEKLY SCHEDULE in MAIN
MENU using DOWN or UP button is highlighted with blue color. The menu above will
appear on monitor.
WEEKLY SCHEDULE
WEEK
START
DURATION
SUN
00: 00
00: 00
OFF
MON
00: 00
00: 00
OFF
WEEK
NONE
NONE
OFF
ENTER
▲ ▼ ◀ ▶ EXIT
When blue bar is on SUN, blue bar movement from SUN to SAT and HOLIDAY can be
selected by DOWN or UP button. To return Main Menu, MENU/ESC button is used.
To move START, DURATION and OFF/ ON, LEFT or RIGHT Button is used. To decide
the time for START time, DURATION and OFF/ ON, time with bold character or OFF/ ON
at that position can be changed by DOWN or UP button .
For example, the blue bar movement by LEFT or RIGHT Button like this;
WEEKLY SCHEDULE
START
SUN
00: 00
WEEKLY SCHEDULE
DURATION
00: 00
START
OFF
SUN
WEEKLY SCHEDULE
START
SUN
00: 00
00: 00
OFF
WEEKLY SCHEDULE
DURATION
00: 00
00: 00
DURATION
START
OFF
SUN
00: 00
DURATION
00: 00
OFF
WEEKLY SCHEDULE
START
SUN
00: 00
DURATION
00: 00
OFF
When blue bar is placed on START, DURATION and OFF/ ON, you can change
value like time or ON/ OFF. When there is no bold character, blue bar can move from SUN
to SAT and HOLIDAY. START means recording starting time. It can be changed from
00:00 to 23:59. DURATION means total recording time duration. HOLIDAY is for holiday
recording setup. It can be adjusted from SUN to SAT.
8. NETWORK SETUP
7
NETWORK SETUP
1
CONNECT
: STATIC/ DHCP
2
3
4
5
6
7
8
9
IP ADD
SUB NET
GATE WAY
DNS
PORT
NTP TIME
TIME ZONE
DDNS STATUS
: 192. 168. 123. 171
: 255. 255. 255. 000
: 192. 168. 123. 254
: 168.126.063.001
: 5000
: OFF
: GMT + 09:00
: NONE/OK/ERR
ENTER
▲ ▼ ◀ ▶ EXIT
To access NETWORK SETUP, press ENTER when NETWORK SETUP in MAIN
MENU using DOWN or UP is highlighted with blue color. The menu above will
appear on monitor.
1) CONNECT: STATIC or DHCP
You DVR can select STATIC IP or DHCP using LEFT or RIGHT Button.
2) IP ADDRESS, 3) SUB NET MASK, 4) GATE WAY:
If static IP be selected, IP address, SUB NET, and GATEWAY should be written
on it manually, according to network environment. LEFT or RIGHT button is used for
movement, DOWN or UP button is used for changing the value of parameter.
If DHCP be selected, your DVR would read network parameters automatically from
network equipment, display them on IP ADD, SUB NET and GATEWAY.
5) DNS:
DNS : Server IP setting to change Domain Name into IP address.
Default value is KT’s Domain Name Server IP.
6) PORT : Port number for TCP/IP connection in DVR
Net-Viewer should have same port Number to access remote DVR through network.
(Ex. 80 TCP www-http World Wide Web HTTP )
(Ex 123 UDP NTP Network Time Protocol )
Default Port No. is 5000. If Port is set as 5000, port number of from 5000 to 5002 is
used in DVR. Therefore, If DVR is used in network environment with firewall, port
number of from 5000 to 5002 should be opened for DVR’s external access.
If IP sharing machine is used with DVR, “port forwarding” should be done.
7) NTP TIME: OFF/ON
DVR can synchronize “standard time” with Time Server using Network Time Protocol.
NOTE: If DNS server is not set properly in fixed IP address, this function will not be
operated.
8) TIME ZONE SETTING
Time information can be synchronized with time server. For example to synchronize
time, GMT + 8 for Taiwan, GMT + 9 for Korea or Japan.
9) DDNS STATUS: Dynamic DNS status display (This DDNS status is just readable.)
It is recommended not to use this DDNS service for fixed IP or IP sharing machine.
NONE – It indicate that DDNS is not used.
ERR - DDNS IP update failure
OK - Normal operation
< How to use DDNS service >
1. Create User ID, password and domain Name in the company which support DDNS
service with free of charge.
(Ex. www.dyndns.org )
2. Access to your DVR using any PC installed Net-Viewer.
3. Input User ID, password, site and “DDNS enable” received from company which
support DDNS service in DDNS setting of remote setup of Net-Viewer.
DVR will be upgraded as soon as DDNS setting by remote setup of Net-Viewer
is finished.
4. Check the status of 8. DDNS STATUS of NETWORK SETUP.
9. ARCHIVING
8
ARCHIVING
1
ARCHIVING TYPE
: SINGLE/ MOTION
2
ARCHIVING TIME
: 1 SEC to 30 MIN
3
ARCHIVE INFO
NAME:
TOTAL:
FREE:
4
ARCHIVE LOG
ENTER
: NONE
▲ ▼ ◀ ▶ EXIT
1) ARCHIVE TYPE: SINGLE or MOTION
For archiving data via USB port, first set-up ARCHIVING TYPE and ARCHIVING
TIME which you want to have using LEFT or RIGHT Button. And then insert USB
memory drive in USB port of DVR front panel.
Press ARCHIVE button in playback or live mode.
SINGLE in ARCHIVE TYPE means that field by field image can be captured in USB
memory drive. MOTION means that it can be captured during the time duration
when you set in ARCHIVE TIME.
Note: Archiving operation through USB Memory Drive can be executed only in
live mode or playback mode.
2) ARCHIVE TIME: 1 to 60 seconds and 30 Minute.
ARCHIVE TIME is time duration which you want to archive in MOTION.
3) ARCHIVE INFO:
First, connect USB memory drive in USB port of DVR front panel. And then enter
menu mode. You can see the information of USB Memory Drive inserted in DVR
like USB memory drive manufacturer, total memory size, available memory size.
4) ARCHIVE LOG: NONE or ENTER
All of log information including DVR power ON/ OFF, recording time, event time
and so on can be backup through USB Memory drive. After backup log file, you
can see backup log information using WORD-PAD of PC. For ARCHIVE LOG, first
select ENTER using LEFT or RIGHT Button. And the press ENTER button.
NOTE: Don’t keep to connect USB Memory drive in USB port of DVR after finishing
DVR power up. And don’t plug out USB Memory drive when it is working.
Please plug out USB memory drive after “Archive LED” turn off. When
playback pictures is archived, archived speed is followed by playback speed.
5) The archived image playback
To play archived image, it needs NetViewer program. For the installation of NetViewer
program in PC, Setup.exe in NetViewer S/W CD can be executed.
To playback archived image file in USB memory driver, First connect USB memory
drive to PC, then execute Netviewer program.
NOTE: For more detail information about NetViewer program, confer the user’s manual
of NetViewer program.
< The procedure of archived file playback using NetViewer program >
A) Install NetViewer program as executing Setup.exe in NetViewer S/W CD.
After finishing installation, next icon will be appeared in PC.
B) Double-click the icon to execute NetViewer Program. Main Window of NetViewer
program will be appeared. (Confer next page figure.)
C) Connect USB Memory drive to USB port of PC.
D) Search archived files using searching icon of NetViewer program.
E) Playback the archived file as double-clicking the file.
NOTE: USB Memory driver usually will be recognized as removable disk in most of PC.
Confer example of recognizing USB Memory drive in PC.
1
2
3
4
5
6
7
8
< NetViewer Program >
NOTE: On the viewer program buttons in Viewer GUI
1. Search Button:
This Search Button can be used to find archived image in USB Memory drive. After
searching the image files, double-click the file. And then it will be playbacked.
2. Slide bar;
In order to move much faster the archived image where you want to see, just drag
this slice bar forward or backward.
3. Move to beginning of archived images
4. Move single frame backward
5. Playback button
6. Stop/ PAUSE button
7. Move single frame forward
8. Move to end of archived images
< Example; USB Memory Drive will usually be recognized as removable Disk in PC >
Removable Disk
10. HDD INFORMATION
9
HDD INFORMATION
1
HARD DISK
: WDC WD1200
TOTAL
: 111GB
FREE
: 111GB
2
FORMAT HDD
: NO
3
OVERWRITE
: OFF
ENTER
▲ ▼ ◀ ▶ EXIT
1) MASTER HDD:
This machine automatically detects HDD, display HDD information in menu like
total HDD capacity and available memory space.
2) FORMAT HDD:
This support quick HDD format function. To format HDD in FORMAT HDD, first select
YES using LEFT or RIGHT Button, and then press ENTER button. Press ENTER
button again after MASTER is displayed. Then quick format is implemented with
CONFIRM.
3) OVERWRITE: Your DVR can be enable or disable HDD overwrite, when HDD is full.
11. Search List
SEARCH LIST
LIST TYPE
ALL
1
10-15-2004 10:20
10-15-2004 11:20
2
10-15-2004 12:20
10-15-2004 13:20
3
10-15-2004 13:20
10-15-2004
4
10-15-2004 14:20
10-15-2004 15:20
5
10-15-2004
16:20
10-15-2004 17:20
6
10-15-2004 18:20
10-15-2004 18:50
7
10-15-2004 19:20
10-15-2004 19:25
8
10-15-2004 20:20
10-15-2004 20:25
9
10-15-2004 21:20
10-15-2004 21:50
10
10-15-2004 22:00
10-15-2004 23:10
ENTER
The number of recorded files
10/ 10
10-15-2004
14:20
Latest recorded file
▲ ▼ ◀ ▶ EXIT
Search list can be sorted all the recorded file as ALL/ TIME/ MANUAL/ ALARM/
MOTION/ SCHEDULE using DOWN or UP button for fast file searching.
SEARCH LIST
10/ 10
LIST TYPE
ALL
1
10-15-2004 11:20
10-15-2004 10:20
10-15-2004
SEARCH LIST
10/ 10
LIST TYPE
ALL
1
10-15-2004 11:20
10-15-2004 10:20
10-15-2004
Change the numbers by highlighting them and using the DOWN or UP button to
increase or decrease the number for year/ month/ date after moving from ALL to
2004-10-** using LEFT or RIGHT Button.
SEARCH LIST
10/ 10
LIST TYPE
ALL
1
10-15-2004 10:20
10-15-2004 11:20
10
10-15-2004 22:00
10-15-2004 23:10
SEARCH LIST
10-15-2004
10/ 10
LIST TYPE
ALL
1
10-15-2004 10:20
10-15-2004 11:20
10
10-15-2004 22:00
10-15-2004 23:10
10-15-2004
To select recorded file for playback,
DOWN or UP button is used after
pressing ENTER button.
.
Playback will be started by pressing
PLAY/ STOP button (▶) button.
NOTE:
1. If PLAY/ STOP button be pressed two times successively, latest recorded file could be
playbacked soon.
2. The example for searching recorded files by TIME.
Search list by TIME can be selected from ALL/ TIME/ MANUAL/ ALARM/ MOTION/
SCHEDULE using DOWN or UP button.
After moving 11-20-2004 date area using LEFT or RIGHT Button (and then related date
character would be turned into bold character), the date which want to search can be
selected by using DOWN or UP button. Then recorded files just after selected date,
time (ex, 11-20-2004 10:33) would be listed as bellows. To playback a recorded file
from listed files, press ENTER button to move listed files. And then press PLAY/ STOP
button (▶) for playback after selecting the recorded file using DOWN or UP button.
SEARCH LIST
LIST TYPE
2/ 2
TIME
11-20-2004 10:33
1
11-20-2004 10:33
11-20-2004
11:20
2
11-20-2004 22:00
11-20-2004
23:10
12. DISPLAY Mode
There are three kind of display modes such as single (as full), QUAD, sequential mode
regardless recording mode. When there are motion detection or alarm triggering, the
video channel which motion is detected or alarm is triggered would be display on monitor
during 30 Seconds. After it pass 30 Seconds, your DVR would display previous display
mode such as full, QUAD or sequential picture.
▶
12: 03: 2004
06: 26: 23 PM
MAIN MENU
1
SYSTEM SETUP
2
DISPLAY SETUP
3
RECORDING SETUP
4
ALARM SETUP
5
MOTION SETUP
6
WEEKLY SCHEDULE
7
NETWORK SETUP
8
ARCHIVING
9
HDD INFORMATION
When your DVR is in recording, playback and network mode,
on left top corner of monitor. But it is on MENU Mode,
▶
disappeared as upper figure.
are displayed
▶
are temporarily
13. RECORDING Mode
There are several kinds of recording modes such as Manual, Schedule, Alarm event,
Motion. Recording quality including high, standard plus, standard, low for all of recording is
decided by the QUALITY setting in RECORDING SETUP Menu. Frame rate, recording
time can be separately selected in each of RECORDING SETUP Menu.
It is recorded on HDD that 4Ch video input signals are multiplexed with field by
field.
1) Manual recording is started by REC/STOP button of front panel.
2) WEEKLY RECORDING can be started by setting in WEEKLY SETUP.
3) Motion Recording can be started when any motions in image are detected.
4) Alarm recording is started by external alarm trigger input.
12: 03: 2004
06: 26: 23 PM
Recording Mode
12: 03: 2004
06: 26: 23 PM
14. PLAYBACK Mode
Normal playback can be started PLAY/ STOP button (▶) after recorded file selection
in search list. While your DVR is in playback mode, the camera channel which want to
watch could be selected by UP(1), RIGHT(2), DOWN(3), LEFT(4) button. Fast forward
(FF, ▶) or fast backward playback (REW ◀◀) can be done by FF (▶▶) and REW
(◀◀) button. In order to freeze picture in playback, PAUSE
button is used. The
button.
movement of single field in still picture mode can be fulfilled by PAUSE
For selecting the forward or backward playback of single field, FF (▶▶) and REW (◀◀)
button would be needed to press before using PAUSE
button.
Your DVR supports x2,x4,x8,x16,x32 playback for Fast Forward, x2,x4,x8,x16 play back
for Fast Backward.
Note: When motion in image is detected or external alarm is triggered, there is pop-up
image display of the channel during 30 seconds. But your DVR doesn’t display pop-up
image display of the channel when your DVR is in playback mode or search list Menu
to minimize user’s inconvenience.
12: 03: 2004
06: 26: 23 PM
Playback Mode
▶
12: 03: 2004
06: 26: 23 PM
15. PTZ Control Procedure
a) Select the camera (which PTZ camera is connected) to control PTZ using UP(1),
RIGHT(2), DOWN(3), LEFT(4) buttons of front panel in your DVR.
b) Press ENTER button to select PTZ mode. PTZ MODE OSD will be displayed on upper
right corner of monitor.
c) Use UP(1), DOWN(3) button for up and down movement of PTZ camera, LEFT(4),
RIGHT(2) for left and right movement and FF (▶▶), REW (◀◀) buttons for zoom IN
and OUT.
d) To escape PTZ control mode, press ENTER button or any button. Then the PTZ MODE
OSD on upper right corner of monitor will be disappeared.
NOTE:
Before using PTZ control mode, please check that right selection of PTZ protocol in PTZ
TYPE of DISPLAY SETUP is done.
IV. Software Upgrade Procedure
1. S/W Upgrade procedure
1) Copy files including - trd400_tar into USB Memory Drive using PC in advance.
2) Turn off power of your DVR.
3) Turn on power of your DVR.
4) Insert USB Memory Drive into USB port in front panel of DVR.
5) Press MENU button.
6) Input password and then press ENTER button.
7) Select SYSTEM SETUP menu in main menu.
* It takes several seconds for your DVR to display SYSTEM SETUP menu because
upgrade files like - trd400_tar has been read into your DVR.
SYSTEM SETUP
1
LANGUAGE
: ENG/CHN
2
VIDEO FORMAT
: NTSC
3
PASSWORD
: ****
4
ADMIN LOCK
: YES
5
TIME FORMAT
: 24HOURS
6
DATE FORMAT
: MM-DD-YY
7
DATE/TIME SET
:
05: 20: 2005
8
DEFAULT
9
REV STATUS
ENTER
10:50:11
: YES / NO
: VERSION
1:1:1
▲ ▼ ◀ ▶ EXIT
* NOTE:
The terminology of 9. REV STATUS of SYSTEM SETUP in version 1.1.1 (current
version) is changed into 9. REV STATUS in version 1.1.2 (new version). After
finishing S/W upgrade, terminology will be changed.
8) Move to 9. REV STATUS of SYSTEM SETUP.
The SYSTEM MENU shows UPGRADE version from 1.1.1 (current) to 1.1.2 (new).
SYSTEM SETUP
1
LANGUAGE
: ENG/CHN
2
VIDEO FORMAT
: NTSC
3
PASSWORD
: ****
4
ADMIN LOCK
: YES
5
TIME FORMAT
: 24HOURS
6
DATE FORMAT
: MM-DD-YY
7
DATE/TIME SET
:
05: 20: 2005
8
DEFAULT
9
REV STATUS
10:50:11
: YES / NO
: UPGRADE
1:1:1 Î 1:1:2
▲ ▼ ◀ ▶ EXIT
ENTER
9) Press RIGHT(2) button of front panel in your DVR.
“9. REV STATUS : UPGRADE” will be changed into “9. REV STATUS : CONFIRM”
SYSTEM SETUP
1
LANGUAGE
: ENG/CHN
2
VIDEO FORMAT
: NTSC
3
PASSWORD
: ****
4
ADMIN LOCK
: YES
5
TIME FORMAT
: 24HOURS
6
DATE FORMAT
: MM-DD-YY
7
DATE/TIME SET
:
05: 20: 2005
8
GMT HOUR SET
9
REV STATUS
ENTER
10:50:11
: 09 HOUR
: CONFIRM
1:1:1 Î 1:1:2
▲ ▼ ◀ ▶ EXIT
10) Press ENTER button of front panel in your DVR.
While “9. REV STATUS : WAIT” is appearing, S/W upgrade will be executed. It
takes around 20 seconds. After completing S/W upgrade, your DVR will be re-booted.
NOTE:
1. After pressing ENTER button for upgrading, USB Memory Driver should not be
plugged out before displaying “INITIALIZING” message in your DVR.
2. Please remove USB Memory Drive from front panel of your DVR, when
“INITIALIZING” character is displayed on monitor.
SYSTEM SETUP
1
LANGUAGE
: ENG/CHN
2
VIDEO FORMAT
: NTSC
3
PASSWORD
: ****
4
ADMIN LOCK
: YES
5
TIME FORMAT
: 24HOURS
6
DATE FORMAT
: MM-DD-YY
7
DATE/TIME SET
:
05: 20: 2005
8
GMT HOUR SET
9
REV STATUS
ENTER
10:50:11
: 09 HOUR
: WAIT
1:1:1 Î 1:1:2
▲ ▼ ◀ ▶ EXIT
11) S/W Upgrade Completion !!!
S/W upgrade version will be seen on 9. REV STATUS of SYSTEM SETUP.
SYSTEM SETUP
1
LANGUAGE
: ENG/CHN
2
VIDEO FORMAT
: NTSC
3
PASSWORD
: ****
4
ADMIN LOCK
: YES
5
TIME FORMAT
: 24HOURS
6
DATE FORMAT
: MM-DD-YY
7
DATE/TIME SET
:
05: 20: 2005
10:50:11
8
GMT HOUR SET
: 09 HOUR
9
REV STATUS
: VERSION
1:1:2
ENTER
▲ ▼ ◀ ▶ EXIT
Upgrade Version
APPENDIX 1. Specification (1/2)
Video Input
4 Ch, NTSC/PAL, 1V peak-to-peak, 75 Ohm, BNC
Audio Input/ Output
1 Ch Input/ 1 Ch Output
Video Output
4Ch loop-through Output. 1 Monitor
Display Resolution
Display Resolution NTSC: 720x480, PAL: 720x576
Display Mode
Single, QUAD, Sequential
Recording Resolution
Full Mode, 4Ch Multiplexing Recording
NTSC: 720x480, PAL: 720x576
Compression Algorithm
M-JPEG (modified)
OS
Embedded Linux
Triplex
Record / Playback / Network
Compression Rate (KB/ image)
(NTSC: 720x240, PAL: 720x288)
Normal image: 13~17 (NTSC), 15~19(PAL)
Complex image: 20~25 (NTSC), 22~27 (PAL)
Recording Frame Rate (IPS)
60 fps (NTSC), 50 fps (PAL)
Recording
Speed (IPS)
60/30/15/10/5/1/0.5 (NTSC), 50/25/12/6/5/1/0.5 (PAL)
Modes
Manual, Schedule, Motion, Event
Display
60 Field per Sec (NTSC), 50 Field per Sec (PAL)
Schedule Recording
Choose recording section at 1min time intervals during days of week
Full-time recording, Holiday Recording option
Status Indicator (LED)
Power, Network, Archive, Record (Button inside)
Event
(Alarm Trigger, Motion)
Selectable input recording speed
Alarm In(4)/ Relay Out(1)
NO, NC selectable. Both NO and NC support in rear panel for Relay Out
Playback
Normal: x1 speed
Duration: Follow/Continue/10sec/20sec/30sec/1,5,10 min
Fast Forward: x2,x4,x8,x16,x32(NTSC, PAL)
Fast Backward: x2,x4,x8,x16(NTSC, PAL)
Move 1 image per pushbutton at still image (STILL Button)
Searching function: Move to search list, Time/ Manual/ Event/ Schedule
Network (GUI or Internet Explorer)
Protocol: TCP/IP, PPP, and DHCP
GUI or Internet Explorer viewing and configuration support
Communication Protocol
RS232 / RS485 (Pan/Tilt/Zoom)
HDD Type
EIDE, ATA-6, 3.5 inch, 7200rpm
APPENDIX 1. Specification (1/2)
HDD Management
Pre-formatting not required (Automatic formatting by system)
(No loss of data by FAT breakage/Efficient HDD space increase)
Data storing in sequence (Not decrease HDD lifetime)
Archiving
USB 1.1 for data export (M-JPEG format)
(Note: Memory Key not included in the package)
Power Supply
AC100-240V, 50-60Hz
Mechanical
Unit Dimension
44(W) x31.5(D) x4.4(H) (17.3 in. x12.4In. x 1.73 In.)
(19" rack mountable, 1U)
Unit Weight
Unit Weight 11lb (5kg)
Ambient Temperature
40° to 104°F (5° to 40°C)
Approval
FCC Class A, CE and cUL
APPENDIX 2. Pin Description of connectors
1. USB Pin Descriptions
1
2. LAN port (RJ-45) Pin Descriptions
5
Pin NO.
1
Pin description
8
Pin NO.
Pin description
1
VCC
1
TXD+
2
D- (TX-)
2
TXD-
3
D+(TX+)
3
RXD+
4
GND
4
No connected
5
SHIELD
5
No connected
6
RXD-
7
No connected
8
No connected
3. RS485 Pin Descriptions
1
3
Pin NO.
DVR
Pin description
Slave Unit like PTZ Camera
Pin NO.
Pin description
1
RS485 D+ (TX +)
?
RS485 D+ (RX +)
2
RS485 D- (TX -)
?
RS485 D- (RX -)
3
GND
4. RS232C Pin (DSUB-9) Descriptions
1
DVR
9
Pin NO. Pin description
External Communication Unit
Pin
Pin description
1
No connected. (DCD)
1
No connected.
2
RXD (Receive Data)
2
RXD
3
TXD (Transmit Data)
3
TXD
4
No connected. (DTR)
4
No connected.
5
GND (System Ground)
5
GND
6
No connected
6
No connected
7
No connected
7
No connected
8
No connected
8
No connected
9
No connected
9
No connected
5. Alarm Input & Outputs Pin Descriptions
1
8
Pin NO.
1-4
Pin description
Sensor input 1 – Sensor input 4
5
Ground
6
Relay output with normal open
7
Relay output with normal close
8
Common
Warranty Guide
The quality of this product is guaranteed by strict quality control process and tests. If the
Product is damaged despite following the instructions provided in the manual, this
Warranty will be in effect, provided the product is damaged within 1 year of purchase.
Warranty Guide
z Check the Product Warranty Sheet to make sure it is still in effect.
z Check the problem again and contact your dealer you purchased from.
z About product repair, exchange, or refund, we follow the “compensation regulation for
customer’s loss” announced by “the Economic Planning Board”.
Warranty
z If the product is damaged despite following the instructions provided in the manual, this
warranty will be in effect, provided the product is damaged within 1 year of purchase.
z Service fee and replacement parts will be charged in below cases:
1. Damaged the user’s carelessness.
2. Damaged due to a natural disaster.
3. Damaged due to the user not following the instructions and cautions written in the
user’s guide
4. Damaged due to incorrect power voltage, and/or frequency being used.
5. If the Product Warranty sheet is expired.
6. Damaged due to an engineer not employed by SIGNALSYNC modifying the system.
z If your system is damaged after the warranty period, free repair service will not be
available. If you wish the system to be repaired, service fee and replacement parts will
be charged.
Warranty
Product/ Model Name
Serial Number
Purchasing Dealer
Purchasing Date
Warranty Period
1 year from the purchasing date
Customer
• The product Warranty Sheet will not be issued again.
• The Product Warranty Sheet must be filled on the same day of the product’s purchase.
• It will be requested to show this warranty to receive free repair service.
NetViewer S/W User’s Manual
Version_1.2
Version_1.3:
1) IE Design modification
2) Remote Configuration
3) Fast searching by time slide bar
in NetSearching.
April, ‘2005
Table of Contents
I. NetViewer Software Installation & Operation
1. Installation
2. NetViewer Program Operations
1) NetViewer Features
2) Main Window
3) Network Connection
4) Image Display Widow Selection
5) The Storage of pictures transmitted through network in local HDD
6) Viewer Program Set-up
7) PTZ Camera Control
8) Remote Searching
9) Local Searching
10) Playback Icons for local playback
11) Print
12) Remote Configuration
13) AVI conversion
II. Remote Viewing by Internet Explorer
I. NetViewer Software Installation & Operation
1. Installation
CAUTION: If an older version of Netviewer software or similar viewer software
has been already installed on your computer, you should uninstall the
software first.
1) Insert the installation CD.
2) Run the Setup.exe file. And following dialog box will be appeared.
Please wait a few seconds.
3) When the following dialog box appears, click Next.
4) Please fill user name and company name in following dialog box, click Next.
5) Please select installation style in following dialog box. “Typical” can selected
for normal installation. And then click Next.
6) Please click Next.
7) Installation is finished.
2. NetViewer Program Operations
1) NetViewer Features
NetViewer Program support such as functions;
ƒ
Live pictures monitoring and saving in local HDD.
ƒ
DVR file list searching, Playback and saving in local HDD
ƒ
Fast Playback by time selecting
ƒ
Remote configuration of all the DVR menu
ƒ
Pan, tilt and zooming Control
ƒ
Printing and JPEG & AVI conversion
2) Main Window
Remote DVR or Local Select
Clock & Network Status
Network Connect Status
Image Display Window
Set-up, Save, Print Function
Recording Status
PTZ functions
DVR Search Icons
Playback Icons
Local Search Icons
Exit Main Window
3) Network Connection
A) DVR Connection
When this DVR connection icon is clicked, below “Log-in” window will be appeared.
B) User Account Selection
C) HQD400 DVR Server IP Address Input
D) HDQ400 DVR Server Port Input
(Default Port is 5000)
E) Password Input
(This password number is same as the
password of your DVR.)
F) Connection
G)Exit this window not to try connection
4) Image Display Widow Selection
A) Single Picture Display
B) QUAD Pictures Display
C) 9 Pictures Display
(for 9CH Expansion)
D) 16 Pictures Display
(for 16CH Expansion)
5) The Storage of pictures transmitted through network in local HDD
The pictures received through network from remote DVR
can be saved in local Hard Disk Driver.
When “REC” icon is pressed , the color of REC status icon
will turn to be “red”. If “REC” icon is pressed again, local
recording will be stopped. And then the color of REC status
icon will turn to be “green”.
6) Viewer Program Set-up
A) User selection
B) IP Address Input (or Changing)
C) PORT Input
D) Video Format Selection
(NTSC or PAL). It needs to select
Video Format NTSC or PAL for
better video quality.
E) Exit after saving set-up parameter
F) Exit without saving set-up
parameter
7) PTZ Camera Control
1) Tilt Up
2) Pan Right
3) Tilt Down
4) Pan Left
5) Pan/Tilt Up-Left
6) Pan/Tilt Up-Right
7) Pan/Tilt Down-Right
8) Pan/Tilt Down-Left
9) Focus Far
10) Focus Near
8) Remote Searching
For searching recorded files in remote DVR, DVR search icon (in above figure) can be
pressed. If this icon is pressed, below figure will be appeared.
1) File List Window
It displays all of recorded file lists
which is transmitted from remote
DVR.
2) All of recorded file list in remote
DVR can be read out by clicking
“this icon (Read List)”.
3) Selected file within File List Window
can be playbacked by clicking “this
icon (Play)”.
4) Stop playback
5) Exit after saving set-up parameter
Viewer Program will palyback the
file, if there is any selected file.
6) “Time Search” enable user to move and playback the given time of selected
recorded file directly. For example, it is possible to playback the recorded
file with 1hour file size from 08:25:14 (AM 8hour 25 Min. 14Sec.) using
above “Time Search Slide bar”.
7) It enables user to clarify recorded files according to the recording style.
9) Local Searching
1) Local Search Mode
2) Current time Display
3) Network Status Display ( Connection or Disconnection)
10) Playback Icons for local playback
STOP/ PAUSE
Playback
Move to Previous frame
Decrease
playback Speed
Move to Next Frame
Increase
playback Speed
Local Recorded File Searching
Playback Speed:
(1X,2X,4X,16X…..)
11) Print
1) After selecting displaying channel which would like to
be printed, click the “Print icon”
2) The window for printing will be appeared as below.
Selected image will be printed as clicking this icon.
3) To make standard JPEG file, click “Save” icon, after selecting image.
4) If “Save” icon is pressed, below window will be appeared. Input file name like
xxx.jpg which want to save. And press “SAVE(S). Then it will be converted as
JPEG file and will be saved.
5) The file converted into xxx.JPG can be opened in any PC using Window media
player and so on by clicking the xxx.JPG file as below window.
12) Remote Configuration
1) SYSTEM SETTING
A) ADMIN LOCK: YES/ NO
If ADMIN LOCK is selected as YES,
password is requested whenever
it goes into menu. If NO, password
isn’t requested.
B) Password Changing
C) Automatic time setting by
GMT+Hour time Server in worldwide
(it is not supported for 4CH DVR)
D) Exit without saving set-up
E) Exit after saving set-up value.
Selected configuration parameters
will be transferred to remote DVR
2) DISPLAY SETTING
A) Channel Selection.
In case of 16CH DVR, No1 to
No16 will be active.
B) Picture Quality Setting
(Brightness, Contrast)
C) PTZ Camera Protocol Setting
D) Dwell Time Setting for
Sequential and SPOT Monitoring.
(SPOT DWELL Time isn’t supported
in 4CH DVR )
E) OSD ON/ OFF Setting
G) Exit without saving set-up
parameter
F) Exit after saving set-up value.
Selected configuration parameters
will be transferred to remote DVR
3) RECORDING SETTING
A) Recording Quality Setting.
B) Frame rate Setting
D) AUDIO: ON/ OFF
Your DVR can select whether to
record audio signal with video signal
together or not.
E) STOP KEY: DISABLE/ ENABLE
This STOP KEY ENABLE can not
stop “recording stop” intentionally.
4) ALARM SETTING
A) FRAME RATE Setting
From 0.5 to 60 Image per seconds
for NTSC, from 0.5 to 50 IPS for PAL.
can be selected.
B) DURATION:
It define recording duration after
alarm is triggered.
C) SENSOR TYPE: NONE/ N.O/ N.C
Normal open or normal close can be
selected for external alarm inputs
D) TRIGGER OUT (Relay Output)
Both dry open and dry contact
through different relay output port
can be supported.
E) BUZZER ALERT
Beep sound from buzzer when
external alarm sensor(s) be triggered.
5) MOTION RECORDING SETTING
A) Camera Selection for motion
setting
B) Motion Area Setting
Y: Active Motion Area
N: inactive motion Area
C) Motion Area SET/RESET
C) Motion Type Setting
Disable/ All area/ Motion Area Setting
D) Sensitivity Setting: 5 steps
From very low, low , normal, high to
very high.
F) Frame Rate Setting
F) Duration Setting
G) BUZZER ALERT Setting
Beep sound from buzzer when
motion is detected.
6) SCHEDULE RECORDING SETTING
A) START time Setting
Start time selection for schedule
recording.
B) Duration time Setting
Actual recording time selection
C) On/ Off Setting
Schedule recording Enable/ Disable.
D) Holiday Recording Setting
* Note:
START means recording starting time. It can be changed from 00:00 to 23:59.
DURATION means total recording time.
HOLIDAY is for holiday recording setup. It can be adjusted from SUN to SAT.
7) HDD SETTING
1. HDD Information Display
It displays total HDD capacity
with HDD manufacturer.
If there is one HDD in DVR, one
HDD capacity. If two HDD, total
capacity of HDD will be displayed.
2. Overwrite On/Off Setting
8) DDNS SETTING
DDNS Setting for IP address.
First, enroll www. dyndns. Org
which supports DNS service with
free of charge for DDNS setting.
And input the information of
ID/password/DDNS site from
above site.
(This password is different with
DVR password.)
This information is transferred to
remote DVR, it will be useful for
user to access remote DVR by
site name because Domain Name
(site name) is utilized, even
though IP address is changed in
floating IP address (DHCP).
13) AVI conversion
1) The saved files in local HDD which is compressed as modified M-JPEG can be
converted into AVI file for playback in any PC using Avi Converter which is generated
by installing NetViewer software. Windows Î All program (P) Î Netviewer Î
Avi Converter is clicked. Then “AVI converter 1.0” window will be appeared.
2) Conversion Procedure
a) Click “File Open” icon as below figure.
b) Select a file to convert into AVI file. And then input file name for converting file.
c) AVI Conversion Program can be executed channel by channel. First, select the
channel which is converted. Then press “MAKE AVI” to convert into AVI file.
Below window will be appeared.
d) Input file name and press “ Save (S)”. Then below window will be appeared.
If compression type is selected, AVI Conversion Program can start AVI conversion.
e) If conversion is finished, below figure will be appeared. To finish it, press “Confirm”.
For another channel conversion, same procedure will be requested.
f) Converted file can be played in any PC using Windows Media Player
and similar media player as below.
II. Remote Viewing by Internet Explorer
1. Open Internet Explorer with IP address which is set-up in NETWORK SETUP of DVR.
Then below dialog box will be appeared.
Input IP address with port No.
For example,
192.168.123.002:5002
2. Please press “Connect” icon on the right corner to access remote DVR.
Then below dialog box will be appeared.
“Connect” icon.
Please input IP Address, Port number and password in below dialog box.
Note:
Password is the number which is stored in DVR.
3. You can view live image of remote DVR through Internet Explorer as below dialog.
4. How to control PTZ Camera and picture display mode.
PTZ Control Icons
- Left and Right
- Up and Down
- Zoom In/ Out
- Focus Near/ Far
Picture Display
Mode
- 4CH/ 9CH/
16CH
In order to control PTZ Camera, right PTZ Camera protocol should be selected in DVR.
The picture area (Cameo) (which PTZ function is needed to control) is selected by
mouse. And then press the PTZ control icon.
5. In order to search all of the recorded files of DVR, “NetSearch” icon can be pressed.
Then below dialog box will be appeared.
6. How to search recorded files of remote DVR.
1) Read List Icon: It is used to read all of recorded files of remote DVR.
All of reading files can be sorted by “Type” which includes Manual, Alarm,
Motion and Schedule.
2) Play: It is used to play one of file selected by mouse from all of lists.
< Playback procedure >
1. Select one file which you want to play by mouse
2. Press “Play” icon for playback.
3. Press “Stop” icon for stop the playback.
4. Press “Exit” icon to return to “live picture”.
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertising