IKUtrax Outdoor Bluetooth Speaker

IKUtrax Outdoor Bluetooth Speaker
IKUtrax
(MXSP-BTS150)
OUTDOOR BLUETOOTH® SPEAKER
WITH NFC FUNCTION
USER MANUAL
PLEASE READ THIS USER MANUAL COMPLETELY BEFORE OPERATING THIS
UNIT AND RETAIN THIS GUIDE FOR FUTURE REFERENCE.
PRODUCT FEATURES
The Maxell IKUtrax is an Outdoor Bluetooth portable Speaker with the following features:
 Wireless playback of music from your Bluetooth enabled mobile phone or devices via
the Bluetooth connection
 Water Resistant & Dustproof (IP55), and Shock Resistant.
 NFC Connectivity
 Up to 33 feet (10 meters) line-of-sight operating distance
 Hands-free phone conversation
 Remotely control your music (play, pause, next track, previous track)
 Aux-in connection providing instant 3.5mm stereo audio cable connection to any device.
GETTING STARTED



Carefully remove the unit and all the accessories from the packaging. Please verify
that you have the Quick Start Guide, 3.5mm AUX-in cable and Micro USB charging
cable before recycling the box.
Fully charge your IKUtrax before initial use.
Use the included Micro USB cable to connect your MXSP-BTS150 to the USB slot of
any PC to charge. The RED LED will turn on while charging and will turn off
automatically when fully charged.
PAIRING MODE
 From OFF, Push and hold the centre button for 8 seconds. After 5 seconds the
speaker will indicate that it is ON. Keep holding without releasing for another 3
seconds, and the speaker will enter Pairing Mode. The LED light will flash Blue
rapidly.
 See your phone/music device manual for pairing instructions.
 Then you will hear a voice prompt while the Pairing successful.
LOCATION OF CONTROLS
TOP
1.
2.
3.
4.
5.
6.
7.
8.
9.
SIDE
FUNCTION BUTTON (ON/ OFF, PLAY/ STOP, PAIR OR PICK UP/ HANG UP)
VOLUME UP OR NEXT SONG
VOLUME DOWN OR PREVIOUS SONG
LED – POWER / CHARGING / PAIRING STATUS INDICATOR
NFC PAIRING AREA
MICROPHONE
HOOK FOR WRIST STRAP
3.5MM AUX IN JACK
CHARGING JACK(MICRO USB)
LED INDICATOR
LED COLOUR
DESCRIPTION
Blue flashing every 1 sec.
Red flashing every 1 sec.
Blue flashing every 1 sec.
Blue flashing every 0.1 sec.
Blue flashing every 5 sec.
Blue flashing every 1 sec.
Red flashing every 0.1 sec.
Red light on
Power ON
Power OFF
Standby
Pairing
Connected
Disconnected
Low Power (standby)
Charging
FUNCTION BUTTON INDICATOR
Behaviour
Press and hold the function key for 5 seconds
Press and hold the function key for 8 seconds
Click function key once
Double click function key during the incoming
ring.
Double click function key
Click function key once
Description
Power turn on/off
Pairing
Answer/End call
Reject call
(Siri—iPhone only)
Play/Pause music
LEFT & RIGHT BUTTON INDICATOR
Behaviour
One click the Vol. key (+) increase; (-) decrease
Adjust Volume
Press and hold the “+” for 3 seconds
Press and hold the “-” for 3 seconds
Next track
Previous track
Description
CHARGING INSTRUCTIONS
This unit operates on a built-in Lithium battery that can be recharged either using the USB
port on your computer or from a USB power adaptor (not included) with a rated output of DC
5V, 500mA and up.
Note: The micro USB CHARGING JACK located on this unit is only designed for charging
the built- in Li-ion battery.
CHARGING THE BATTERY FOR FIRST TIME
1.) Charge the built-in Lithium battery a minimum of 3.5 hours prior to first use.
Plug the unit into the USB port on your computer or into a USB power adaptor
(Not included) using the included USB cable.
2.) The LED indicator will turn red while charging and turn-off automatically when the unit is
fully charged. Unplug the USB cable from the power source once the battery is fully
charged.
RECHARGING THE INTERNAL BATTERY
After prolonged use, the internal battery will become weak and the operation may become
intermittent. When the internal battery charge is very low, the Indicator LED will flash red
alerting you to recharge the internal battery as soon as possible.
Plug the Speaker into a USB port on your computer or into a DC 5V, 500mA and up USB
power adaptor (not included) using the included USB cable. Disconnect the USB cable from
the Speaker as soon as it is fully charged.
Charging in Power ON mode

The Indicator LED is RED + BLUE flashing while charging.

The Indicator LED will turn off automatically when the battery is fully
charged.
Note: 1. Charging time will vary if you are listening to music while charging the internal
battery. We recommend you switch off the Speaker power during the
charging process.
2. To prolong the life of a rechargeable battery, it is recommended that you
completely discharge it before fully charging it again.
3. Rechargeable batteries need to be cycled for maximum performance and
longer battery life. If you don’t use the speaker that often, make sure to
recharge the battery at least once a month in order to keep the internal
battery working properly.
Charging in Unit Power OFF mode

The Indicator LED is RED while charging.

The Indicator LED will turn off automatically when the battery is fully
charged.
Battery Note and Care








Do not burn or bury batteries.
Do not puncture or crush.
Do not disassemble.
Lithium batteries must be recycled. Do not dispose of in the trash.
Use only chargers rated for Li-ion cells. Be sure the charger’s voltage and current
settings are correct for the battery pack being charged.
Charge batteries on a fireproof surface and away from flammable items or liquids.
Batteries should NEVER be left unattended while charging. Only adults should
charge the batteries.
Follow the manufacturer’s instructions for charging the product and do not charge
longer than recommended. Unplug the charger when the battery is charged or not in
use.
NOTE: The Speaker is not magnetically shielded and may cause colour distortion on the
screen of some TVs or video monitors. To avoid this, you may need to move the unit further
away from the TV or monitor if an unnatural colour shifts or image distortion occurs.
ON/OFF
1. Hold down the function button for 5 seconds to turn the unit ON. The LED Indicator will
flash blue for 5 seconds, and there will be an Audio Notification to indicate that it is now
ON.
2. To turn the unit OFF, hold the function key for 5 seconds. The LED Indicator will flash red
for one second, and there will be another Audio Notification. Don’t forget to turn off the
Bluetooth feature on your cell phone.
SPEAKER OPERATIONS
PAIRING (LINKING) A BLUETOOTH ENABLED MOBILE PHONE OR OTHER BLUETOOTH
ENABLED DEVICE TO THE MXSP-BTS150
1. If the IKUtrax has never been paired with a Bluetooth device before. You need to follow
the pairing instructions below to link the speaker with your Bluetooth device.
 Push and hold the centre button for 8 seconds. After 5 seconds the speaker will
indicate that it is on. Keep holding without releasing for another 3 seconds, and the
speaker will enter Pairing Mode. The Indicator LED will flash blue rapidly.
 The Speaker is ready to pair (link) with your Bluetooth device.
 Turn on the Bluetooth function of your mobile phone and enable the search or scan
function to find MXSP-BTS150.
 Select MXSP-BTS150 from the device list when it appears on your device screen.
2. After turning on the IKUtrax, the unit will search for the last paired device. The LED
INDICATOR will flash rapidly in blue. If the unit finds the paired Bluetooth device, a beep
is heard and the LED INDICATOR will begin flashing at a slower rate.
3. After successfully pairing (linking), you can begin playing music from your Bluetooth
device wirelessly to the Speaker.
4. Press the Volume Up (+) / Down (-) button on your Bluetooth device to adjust to the
desired volume level. Alternatively, press the “+” button on the speaker to increase the
volume. A beep alert sounds when the volume has reached the maximum level. Press the “-”
button to decrease the volume.
Notes:
1. Refer to the manual of your mobile phone, tablet, PC, computer or other Bluetooth
enabled device for Bluetooth operation, since it may vary from model to model.
2. Your Bluetooth enabled device will not play the music through the Speaker, even if
connected (linked), if the device does not support A2DP profile.
3. If you are pairing (linking) your computer to the IKUtrax using Bluetooth, you may
need to set the Speaker as your computer’s default sound device.
4. If the IKUtrax is left idle for about 5 minutes without linking to any Bluetooth enabled
device, the Bluetooth function will automatically turn off to save battery power.
Using IKUtrax as a Hands-free Bluetooth Speakerphone.
1. Link your mobile phone to the IKUtrax via Bluetooth as described above.
2. When receiving an incoming call on your mobile phone, press the Function key on the
Speaker to switch the incoming call from your mobile phone to the IKUtrax Speaker.
3. Adjust the volume control of the speaker to obtain the desired sound level.
4. To end the call, just press the function key again on your IKUtrax. A short beep sound will
be heard and the call will end. If you were playing music from your mobile phone to the
IKUtrax before answering the call, the music will automatically resume playing when you
hang up.
5. To ignore an incoming call, simply double click the function key.
Re-linking to the mobile phone
If your mobile phone is already paired (linked) with the Speaker, but became
unlinked even with both Bluetooth devices turned on, then you can re-link them by:
1. Turning off the Speaker and then turning it on again to re-link your mobile phone.
2. You can also re-link the Speaker by using Bluetooth operation on your mobile
phone. Please refer to the operation manual of your cell phone for more
information.
VOLUME CONTROL
Repeatedly press the “+” button to increase the volume. A beep alert sounds when volume
has reached the maximum level. Repeatedly press the “-” button to decrease the volume.
(Do not hold the “+” or “-“ buttons to change the volume, this will skip tracks)
REMOTE CONTROL MUSIC TRACKS
Press the function button to play or pause the current track. To change to a different song,
press the “+” or “-“ on the top of the speaker. You can also use your mobile device.
AUX-in JACK
Connect any music device by using the 3.5 mm cable included.
TAP TO LINK WITH NFC
Install the Android Apps provided to the NFC-equipped Smartphone. Simply align the NFC
LOGO and hold for 1-2 seconds to activate Bluetooth, pair the two devices, and stream your
music. ”Connect” is shown on the phone screen when MXSP-BTS150 is connected
successfully. Tap again to disconnect two devices and the phone will show “Disconnect” on
the screen.
CARE AND MAINTENANCE
1.
2.
Avoid operating your unit under direct sunlight or in hot, humid or dusty places.
Keep your unit away from heating appliances and sources of electrical noise such as
fluorescent lamps or motors.
CLEANING THE UNIT

To prevent fire or shock hazard, disconnect your unit from the USB port and power
source when cleaning.

The finish on the unit may be cleaned with a dust cloth and cared for as other furniture.
Use caution when cleaning and wiping the plastic parts.

If the cabinet becomes dusty wipe it with a soft dry dust cloth. Do not use any wax or
polish sprays on the cabinet.

If the front panel becomes dirty or smudged with fingerprints it may be cleaned with a
soft cloth slightly dampened with a mild soap and water solution. Never use abrasive
cloths or polishes as these will damage the finish of your unit.
CAUTION: Never allow any water or other liquids to get inside the unit while cleaning.
TROUBLESHOOTING
Symptom
Not Charging
No Sound
Sound is
distorted.
Unit gets warm
after extended
play at high
volume.
Possible Problem
The USB power adaptor
(not included) is not
plugged into a wall outlet or
the USB cable (included) is
not plugged into the micro
USB jack on the side of the
IKUtrax.
Wall outlet is not
functioning.
Computer USB port is not
functioning.
The IKUtrax battery is
dead.
The IKUtrax is not linked
with your mobile phone.
The IKUtrax placement is
out of range.
Volume set too low.
Volume level is set too
high.
Solution
Plug the USB power adaptor (not included)
into a wall outlet and plug the USB cable
(included) into the micro USB jack on the side
of the IKUtrax.
Plug another device into the same outlet to
confirm the outlet is working.
Make sure your computer power is turned on
and try another USB port.
Recharge the IKUtrax battery.
Go through “Speaker Operations” process to
link the Speaker
Relocate the IKUtrax within Bluetooth
operating range 10 meter (33 feet).
Increase the volume of your device.
Decrease the volume of your device.
Sound source is distorted.
If the source sound file is of poor quality,
distortion and noise are easily noticeable at
high volume level. Try a better sound quality
music file again.
This is normal.
Turn the unit off for a period of time or lower
the volume.
SPECIFICATIONS
General Specifications
Compatible I/O
Bluetooth v3.0 (Class II: 10m range)
Support Profile
HSP, HFP, A2DP, AVRCP
Output Frequency Range
2.400~2.484 GHz
Frequency Hopping
FHSS(Frequency Hopping Spread Spectrum)
Bluetooth PIN code
Water Proof
0000(simple pairing)
IPx5
Multi-point
Support two devices
Paired device
4
RF Performance
Max. +4dBm Class 2
Near Field communication Yes
Speaker Specifications
Rated Impedance
4Ω ± 15%
Resonant FREQ.(fo)
150Hz ± 30Hz
Output S.P.L
78dB ±2dB (1M/W @1KHz)
Rated FREQ. Range
150Hz~20KHz
Rated Power Input
2.5W+2.5W
Max. Power Input
5W
Microphone/ Audio input Specifications
Sensitivity
-42dB
Output Impedance
2.2KΩ
S/N Ratio
58dB
Electrical Specifications
Supply Voltage
Battery Capacity
Power Charge Consumption
Standby Power Consumption
Music play/ Phone call Power Consumption
Power Off Standby Time
Battery Charge time
5V
950mA
450mA
1~2mA
1/8 rated power: 8 hours
120 hours
2.5 hours
At Maxell, environmental and social responsibility is a core value of our business. We are dedicated to
continuous implementation of responsible initiatives with an aim to conserve and maintain the environment
through responsible recycling.
®
The Bluetooth word mark and logos are registered trademarks owned by Bluetooth SIG, Inc. and any use of
such marks by Hitachi Maxell Global Ltd. is under license. Other trademarks and trade names are those of their
respective owners.
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertisement