Shimano DURA-ACE SL-BS79 Bar end shifter Technical Service Instructions
Pubblicità
Pubblicità
3
For Front Lever
4
5
2
1
DURA-ACE Bar End Shifting Lever
SL-BS79
10-Speed
1
4
For Rear Lever
5
3
2
6 6
ITEM
NO.
*
*
1
2
3
4
5
6
SHIMANO
CODE NO.
Y-6RP 02000
Y-65A 24200
Y-6J6 01000
Y-643 43010
Y-6RP 50000
Y-6RP 49000
Y-628 90010
Y-86B 22000
DESCRIPTION
Lever Fixing Screw (M5 x 19) for Rear
Lever Fixing Screw (M5 x 17) for Front
Lever Boss Cover for Rear
Lever Boss Cover for Front
Lever Axle
Body Fixing Bolt
Segment Unit
Outer Cable Guide
A: Same parts.
B: Parts are usable, but differ in materirals, appearance, finish, size, etc.
Absence of mark indicates non-interchangeability.
SL-BS78 SL-BS64
INTERCHANGE-
ABILITY
A
A
A
A
A
A
0811-2873A
General Safety Information
WARNING
– To avoid serious injuries:
• Obtain and read the service instructions carefully prior to installing the parts. Loose, worn or damaged parts may cause the bicycle to fall over and serious injury may occur as a result. We strongly recommend only using genuine Shimano replacement parts.
• Read these Technical Service Instructions carefully, and keep them in a safe place for later reference.
Note
• For smooth operation, use the specified outer casing and bottom bracket cable guide.
• Because the high cable resistance of a frame with internal cable routing would impair the SIS function, this type of frame should not be used.
• The sliding surfaces of the inner cable and outer casing should be greased before use.
• The shifting lever can be installed to handlebars with diameters of 19.0 – 22.0 mm.
• Operation of the levers related to gear shifting should be made only when the front chainwheel is turning.
• Parts are not guaranteed against natural wear or deterioration resulting from normal use.
• For any questions regarding methods of handling or maintenance, please contact the place of purchase.
In order to realize the best performance, we recommend that the following combination be used.
Series
Shifting lever
Rear derailleur
Front derailleur
Outer casing
Inner cable
Bottom bracket guide
Sprockets
DURA-ACE
SL-BS79
RD-7900
FD-7900
SP41 sealed outer casing
1.2 mm dia. (stainless steel)
SM-SP17
10
3.
Install the lever to the body unit.
Tightening torque:
2.5 - 3 N·m {21 - 26 in. lbs.}
Installation of the lever
When installing the components to carbon frame/handle bar surfaces, verify with the manufacturer of the carbon frame/parts for their recommendation on tightening torque in order to prevent over tightening that can cause damage to the carbon material and/or under tightening that can cause lack of fixing strength for the components.
The illustration shows an explanation of the case where the shifting lever is installed to drop handlebars.
Install the front lever in the same way.
1.
Attach the body unit to the handlebar, and then use a 5 mm Allen key to turn the body fixing bolt counterclockwise to tighten it.
Tightening torque:
5 - 6 N·m {43 - 52 in. lbs.}
Technical
Service Instructions
SL-BS79
SI-6RP0A-001
Bar End
Shifting Lever
Body fixing bolt
Body unit
2.
Install the lever boss to the body unit.
5 mm Allen key
4.
Install the outer casing stopper to the brazed-on boss.
Brazed-on boss (M5)
Stopper fixing bolt
3 mm Allen key
Outer casing stopper (SM-CS50)
Tightening torque:
1.5 - 2 N·m {13 - 17 in. lbs.}
Lever grip
Set so that the projection faces downward.
Right: Thickness
(large)
Left: Thickness
(small)
5.
With the outer casing placed along the handlebar, cover the outer casing with the outer casing guide, and then use tape or similar material to provisionally attach it to the handlebar.
Outer casing guide
One Holland, Irvine, California 92618, U.S.A. Phone: +1-949-951-5003
Industrieweg 24, 8071 CT Nunspeet, The Netherlands Phone: +31-341-272222
3-77 Oimatsu-cho, Sakai-ku, Sakai-shi, Osaka 590-8577, Japan
Please note: specifications are subject to change for improvement without notice. (English)
© May 2008 by Shimano Inc. XBC SZK Printed in Japan.
Lever boss
Tape
6.
Wrap the handlebar with bar tape.
Scarica
Pubblicità