98-05204 R1 US IC18 Sprayer User Manual
IC18 SPRAYER
JOB COMPUTER
U S E R
Software version 1.06
M A N U A L
COPYRIGHTS
© 2012 TeeJet Technologies. All rights reserved. No part of this document or the computer programs described
in it may be reproduced, copied, photocopied, translated, or reduced in any form or by any means, electronic or
machine readable, recording or otherwise, without prior written consent from TeeJet Technologies.
TRADEMARKS
Unless otherwise noted, all other brand or product names are trademarks or registered trademarks of their
respective companies or organizations.
LIMITATION OF LIABILITY
TEEJET TECHNOLOGIES PROVIDES THIS MATERIAL “AS IS” WITHOUT WARRANTY OF ANY KIND, EITHER
EXPRESSED OR IMPLIED. NO COPYRIGHT LIABILITY OR PATENT IS ASSUMED. IN NO EVENT SHALL
TEEJET TECHNOLOGIES BE LIABLE FOR ANY LOSS OF BUSINESS, LOSS OF PROFIT, LOSS OF USE OR
DATA, INTERRUPTION OF BUSINESS, OR FOR INDIRECT, SPECIAL, INCIDENTAL, OR CONSEQUENTIAL
DAMAGES OF ANY KIND, EVEN IF TEEJET TECHNOLOGIES HAS BEEN ADVISED OF SUCH DAMAGES
ARISING FROM TEEJET TECHNOLOGIES SOFTWARE.
To ensure optimal use of the equipment, please read this manual thoroughly. Please contact TeeJet Technologies
Customer Support or an authorized TeeJet Technologies dealer if additional support is required.
RESPONSIBILITY FOR USE OF THIS PRODUCT
Regarding responsibility for use of this product, we refer to our sales and delivery terms which states:
Product Usage
Any use of the product is at the sole risk of the buyer. The buyer is therefore not entitled to any form for
compensation caused by, for example, any of the following:
►Disturbance to/from any electronic services or products that do not conform to the standards for CE marketing;
►Missing or poor signal coverage or a succession hereof from external transmitters/receivers used by the buyer;
Functional faults which apply to or from a PC-program or PC equipment not delivered by the seller;
►Faults that may arise from the buyers’ negligence to react to warnings and fault messages from the product
or that can be traced to negligence and/or absent constant control of the work carried out in comparison to the
planned job.
When implementing any new equipment the buyer must take great care and pay attention. Any doubts as to the
correct operation/use should result in contacting the seller’s service department.
ISOBUS Job Computer : IC18 Sprayer
Table of Contents
CHAPTER 1– PRODUCT OVERVIEW
1
OPTIONAL SYSTEM COMPONENTS
2
CONFIGURATIONS4
7
APPLICATION MODE
8
PAGE LAYOUT AND NAVIGATION
9
Home Screen................................................................................................................................ 9
Transport Mode............................................................................................................................ 9
Operation Mode.......................................................................................................................... 10
Main Setup Mode.........................................................................................................................11
Main Setup Menu Icons and Section Overviews.............................................................. 12
CHAPTER 3 – MAIN SETUP IN SPRAYER MODE
15
Main Setup Screen........................................................................................................................................16
Master Screen.................................................................................................................................................17
Home Screen...................................................................................................................................................17
COUNTERS18
98-05204 R1 US
OPERATION
SETUP
Trip Counters...................................................................................................................................................19
Active Trip Counter........................................................................................................... 19
Area Counter.................................................................................................................... 19
Distance Counter.............................................................................................................. 19
Time Counter.................................................................................................................... 19
Volume Counter................................................................................................................ 19
Campaign Counters......................................................................................................................................20
Area Counter.................................................................................................................... 20
Volume Counter................................................................................................................ 20
Time Counter.................................................................................................................... 20
Total Counters.................................................................................................................................................20
Area Counter.................................................................................................................... 20
Volume Counter................................................................................................................ 20
GETTING STARTED
START UP
OVERVIEW
7
i
APPENDIX
CHAPTER 2 – GETTING STARTED
ISOBUS Job Computer : IC18 Sprayer
Time Counter.................................................................................................................... 20
Export Counters.............................................................................................................................................21
JOB PARAMETERS
22
Active Trip Counter........................................................................................................... 22
Preset Application Rates................................................................................................... 22
Nozzle............................................................................................................................... 22
MACHINE23
OVERVIEW
Filling..................................................................................................................................................................24
Actual Content.................................................................................................................. 24
Density.............................................................................................................................. 24
Density Factor................................................................................................................... 24
Full Tank............................................................................................................................ 24
Operation.........................................................................................................................................................25
Application Rate Step....................................................................................................... 25
Speed Source................................................................................................................... 25
Simulated Speed.............................................................................................................. 25
Implement Parameters................................................................................................................................26
Section Width.............................................................................................................................. 26
Boom Section Width......................................................................................................... 26
One-Touch Equal Widths.................................................................................................. 26
Nozzle Preset Setup................................................................................................................... 27
Nozzle Preset................................................................................................................... 27
Nozzle Type...................................................................................................................... 27
Nozzle Size....................................................................................................................... 27
Low Pressure Limit........................................................................................................... 28
High Pressure Limit.......................................................................................................... 28
Reference Flow................................................................................................................. 28
Reference Pressure.......................................................................................................... 28
Factory Settings................................................................................................................ 28
Regulation Parameters............................................................................................................... 29
Valve Calibration, Rough.................................................................................................. 29
Valve Calibration, Fine...................................................................................................... 29
Nozzle Spacing................................................................................................................. 30
Regulation Mode............................................................................................................... 30
Calibrations......................................................................................................................................................31
Implement Speed Sensor........................................................................................................... 31
Manual Calibration............................................................................................................ 31
Automatic Calibration........................................................................................................ 31
Flow Sensor................................................................................................................................ 32
GETTING STARTED
SETUP
OPERATION
APPENDIX
ii
www.teejet.com
ISOBUS Job Computer : IC18 Sprayer
Manual Calibration............................................................................................................ 32
Automatic Calibration........................................................................................................ 32
Alarm Configurations...................................................................................................................................33
CAN Speed Source Timeout............................................................................................. 33
Active Trip Count Information............................................................................................ 33
Tank Content Minimum..................................................................................................... 33
OEM....................................................................................................................................................................34
USER INTERFACE
35
Use Preferred VT.............................................................................................................. 35
This IC18.......................................................................................................................... 35
Pair with Switchbox........................................................................................................... 35
Pair with BoomPilot ECU.................................................................................................. 35
Currently Paired With Information..................................................................................... 36
Show Number on Soft Key............................................................................................... 36
Sprayer Number (FI)......................................................................................................... 36
COMMUNICATION37
HELP38
AUTOMATIC OR MANUAL REGULATION MODE
43
OPERATION MODE OVERVIEW
44
APPLICATION RATE OPTIONS
GETTING STARTED
OPERATION
Keys Descriptions....................................................................................................................... 45
Section and Icon Descriptions.................................................................................................... 46
Master Screen.................................................................................................................................................48
Home Screen...................................................................................................................................................48
49
98-05204 R1 US
SETUP
43
iii
APPENDIX
CHAPTER 4 – OPERATION MODE
OVERVIEW
Diagnostic........................................................................................................................................................39
Test Input.................................................................................................................................... 39
Test Output................................................................................................................................. 40
Liquid Valve PWM Dutycycle............................................................................................ 40
Liquid Valve Direction....................................................................................................... 40
Master Valve..................................................................................................................... 40
Section Valves.................................................................................................................. 40
VT Data....................................................................................................................................... 41
TECU.......................................................................................................................................... 41
About.................................................................................................................................................................41
ISOBUS Job Computer : IC18 Sprayer
Target Rate Percentage Increase/Decrease..........................................................................................49
Regulation Valve Manual Open/Close...................................................................................................49
Target Rate.......................................................................................................................................................50
With Switchbox........................................................................................................................... 50
Without Switchbox...................................................................................................................... 50
BOOM SECTIONS
51
On/Off Sections from the Left or Right..................................................................................................52
Without Switchbox...................................................................................................................... 52
With Switchbox........................................................................................................................... 52
Start/Stop Application.................................................................................................................................53
Without Switchbox...................................................................................................................... 53
With Switchbox........................................................................................................................... 53
Master Stop Key.............................................................................................................................................54
With Switchbox........................................................................................................................... 54
INFORMATION KEY
55
TRANSPORT MODE
56
OVERVIEW
APPENDIX A - FACTORY SETTINGS & RANGES
57
APPENDIX B - UNIT SPECIFICATIONS
61
GETTING STARTED
SETUP
OPERATION
APPENDIX
iv
www.teejet.com
ISOBUS Job Computer : IC18 Sprayer
CHAPTER 1– PRODUCT OVERVIEW
98-05204 R1 US
1
APPENDIX
OPERATION
SETUP
GETTING STARTED
OVERVIEW
Congratulations on the purchase of your new IC18 ECU built on the ISOBUS architecture. This IC18 unit has
the capability of either sprayer or NH3 control when integrated into the implement of either capability. When used
within the guidelines of this manual, the IC18 controller will be a reliable application tool.
This manual covers the Sprayer functions of the IC18 ECU. For NH3 functions, see manual number 98-05230.
Use with your existing VT or Matrix® 570VT
• Works seamlessly and displays on any ISOBUS VT
• Easy navigation menu and data rich display
• IC18 Sprayer ECU suitable for use with NH3 and liquid fertilizer
• Automatic boom section control upgrade option
• Variable rate control available providing your VT has GPS and task control capability
• Easy navigation menu and data rich display
• Add additional ISOBUS ECUs as your needs change
• Provides basic rate control
• Standardized plugs, cables and software simplify installation and connectivity and result in true “plug and
play” technology. IC18 ECU resides on the implement, reducing hardware in the cab
Figure 1-1: IC18 Job Computer
ISOBUS Job Computer : IC18 Sprayer
OPTIONAL SYSTEM COMPONENTS
Matrix 570VT
The Matrix 570VT is a simple to operate, ISOBUScertified 5.7″ (14.5 cm) color touch screen display
suitable for bright daylight and nighttime operation
Figure 1-2: Matrix 570VT
OVERVIEW
Switchbox
GETTING STARTED
Manual section control with remote master capibility.
The switchboxs are available in two configurations.
►9 sections output or 8 sections and a master output
►6 sections output or 5 sections and a master output
Figure 1-3: Switchboxes
SETUP
OPERATION
APPENDIX
2
www.teejet.com
IC18 Spreader
Electronic Control Unit
Use with your existing VT or the Matrix 570VT for dry
product application
• Works seamlessly and displays on any ISOBUS VT
• Easy navigation menu and data rich display
• Add additional ISOBUS ECUs as your needs
change
• Provides basic rate control or variable rate if
the connecting VT has variable rate task control
capabilities
• Standardized plugs, cables and software simplify
installation and connectivity and result in true “plug
and play” technology. IC18 ECU resides on the
implement, reducing hardware in the cab
Figure 1-4: IC18 Spreader Electronic Control Unit
ISOBUS Job Computer : IC18 Sprayer
BoomPilot
Electronic Control Unit for IC18
98-05204 R1 US
3
APPENDIX
OPERATION
SETUP
GETTING STARTED
OVERVIEW
BoomPilot (automatic boom section control) is
possible in combination with software built into the
IC18 Sprayer/NH3 Electronic Control Unit (ECU).
The ECU should be combined with the appropriate
cable to interface with your BoomPilot system, spray
controller and/or spraying machine for quick and easy
installation. Electronic Control Units and their related
cables are designed to control as many boom sections
as the spray controller to which they are connect, up to
a maximum of 9 boom sections.
Figure 1-5: BoomPilot Electronic Control Unit
ISOBUS Job Computer : IC18 Sprayer
CONFIGURATIONS
The following diagrams are reflective of typical IC18 Job Computer configurations. Due to the variety of possible
configurations, these should be used for reference purposes only.
Figure 1-6: IC18 Sprayer Retro Kit to Matrix 570VT Harnessing with BoomPilot ECU and Optional Switchboxes
Matrix 570 VT
75-05024
6 Boom Switchbox
78-30011
9 Boom Switchbox
78-30012
GPS Antenna
78-50155
BoomPilot ECU
78-08070
Matrix
ISOBUS ABSC
45-05776
IC18 ECU Sprayer/NH3
78-08069
50-05177
Dust Cap
45-09022
XX/XX
OVERVIEW
Matrix 570VT
to Incab
Module
45-05824
CONNECT
TO
BATTERY
ISOBUS Incab Module
45-09022
ISOBUS Hitch to IC18 Harness
45-09026
CONNECT
TO
BATTERY
GETTING STARTED
SETUP
to TeeJet 8xx series
flow control harness
IC18 to TeeJet Sensors Harness
45-10121
OPERATION
Included in TeeJet Retro Kit
APPENDIX
4
www.teejet.com
IC18 to Raven Sensors Harness
45-10122
SPEED
to Raven flow control
harness-16 position
5V Regulator for 5V Raven Flow Meter Power
Included in Raven 440-460 Retro Kit
ISOBUS Job Computer : IC18 Sprayer
Figure 1-7: IC18 Sprayer TeeJet Retro Kit to Matrix 570 VT Harnessing. With optional Rate Controller and Matrix
570G for section control and Mapping capabilities
Matrix 570 VT
75-05024
Rate Controller
Switchbox
to 570G CAN
45-05823
IC18 ECU Sprayer/NH3
78-08069
Matrix Pro 570G
Matrix Pro 840G
Matrix
Capped 4 position DT for
ISOBUS connections
45-09022
XX/XX
CONNECT
TO
BATTERY
ISOBUS Incab Module
45-09022
ISOBUS Hitch to IC18 Harness
45-09026
CONNECT
TO
BATTERY
GETTING STARTED
OVERVIEW
Matrix 570VT
to Incab
Module
45-05824
SETUP
to Raven flow control
harness-16 position
5V Regulator for 5V Raven Flow Meter Power
Included in Raven 440-460 Retro Kit
OPERATION
Included in TeeJet Retro Kit
SPEED
98-05204 R1 US
5
APPENDIX
to TeeJet 8xx series
flow control harness
IC18 to TeeJet Sensors Harness
45-10121
IC18 to Raven Sensors Harness
45-10122
ISOBUS Job Computer : IC18 Sprayer
OVERVIEW
GETTING STARTED
SETUP
OPERATION
APPENDIX
6
www.teejet.com
ISOBUS Job Computer : IC18 Sprayer
CHAPTER 2 – GETTING STARTED
• A firm touch is required when selecting a screen icon.
• Settings are NOT automatically saved when selected. The ACCEPT KEY
must be selected to save the
setting. Select the ESCAPE KEY
to escape without saving settings and return to the previous menu.
• The console needs to be cycled off and back on when changing or attaching equipment to the system.
• The menu structure on your display might vary from the one displayed in this User Manual depending on the
virtual terminal being used.
START UP
Power is continuously supplied to the job computer. The virtual terminal will give access to the job computer
options and operation.
Figure 2-1: Master Screen - Crop Sprayer Mode
Matrix VT Setup Key
OVERVIEW
IC18 Crop Sprayer
GETTING STARTED
Other options as available on
ISOBUS system
98-05204 R1 US
7
APPENDIX
OPERATION
SETUP
Master Screen Key
ISOBUS Job Computer : IC18 Sprayer
APPLICATION MODE
The IC18 job computer is programed to be either a sprayer or NH3 applicator. This setting has been established
before leaving the factory, but it can be changed after purchase with assistance from TeeJet Technologies
Customer Service or your local dealer through the OEM setup menu options.
Figure 2-2: Crop Sprayer
Cnt
1
470 gal
1.14 ac
+
5.0
mph
1 3 11
5%
42
G PA
0
psi
Figure 2-3: NH3 Applicator
OVERVIEW
Cnt
1
0.0
mph
0 lbN
1 3 11
0.00 ac
0.0
lb/min
GETTING STARTED
+
5%
SETUP
0.0
0.0
lb/ac
lb/ac
This manual discusses specifically the functions and options in Crop Sprayer Mode. See the specific IC18 NH3
User Manual for functions and options in NH3 Mode.
OPERATION
APPENDIX
8
www.teejet.com
ISOBUS Job Computer : IC18 Sprayer
PAGE LAYOUT AND NAVIGATION
The Master Screen gives access to the systems currently available on your VT. From the Master Screen, the
Home Screen gives access to the IC18’s available functions.
Home Screen
The Home Screen gives access to the IC18’s available functions: Operation Mode, Transport Mode and
Main Setup.
Figure 2-4: Home Screen - Crop Sprayer Mode
Operation Mode
Regulation Mode
Current selection, Auto/Manual, is highlighted with a green dot.
Transport Mode
Main Setup Mode
OVERVIEW
Toggle Preset Target Rate
Master Screen Key
Quick View
Information Based on Current Active Trip
GETTING STARTED
Transport Mode
While in Transport Mode, all operation functions are locked off and cannot be activated.
Figure 2-5: Transport Mode
SETUP
Home Key
OPERATION
Speedometer
98-05204 R1 US
9
APPENDIX
Master Screen Key
ISOBUS Job Computer : IC18 Sprayer
Operation Mode
Information on the Operation screen will vary depending on the parameters set by the user and the OEM.
Figure 2-6: Operation Mode Screen Overview
Applied Area
Applied Volume
Active Trip Count Number
Alert Warning
Cnt
5
Speed/Application Information
5.2
Remaining Tank Contents
mph
Density
Flow Based or Pressure Based
4070 gal
Cnt
Target Rate Indicator
Application Rate
Target Rate Percentage Increase/Decrease
1.14 ac
5
5.2
1 3 11
mph
4 0 7 0+ g a5 %l
2 8 35
Cnt
G PA
50.0
1 3 11
mph
Boom Sections
Nozzle Type
Recommended Pressure Range
1.14 ac
+
5%
4070 gal
1.14 ac
283
+
5%
283
G PA
1 3 11
G PA
0
psi
1
Current Working Pressure
0
psi
1
OVERVIEW
Current Pressure Rate
ECU ID Number
0
psi
NH3 Mode Active
Auto/Manual Mode Key
GETTING STARTED
Manual Mode Regulation Valve Open Key
(flow and pressure will increase)
Cnt
5
5.2
mph
4070 gal
Cnt
1.14 ac
5
5.2
1 3 11
mph
4 0 7 0+ g a5 %l
2 8 35
Cnt
G PA
50.0
1 3 11
SETUP
mph
1.14 ac
+
5%
4070 gal
283
G PA
1 3 11
1.14 ac
+
5%
283
G PA
Manual Mode Regulation Valve Close Key
(flow and pressure will decrease)
Home Key
Next Page Key
Start/Stop Key
Left Boom Sections On Key
Master Stop Key
Left Boom Sections Off Key
Information Key
Right Boom Sections On Key
Tank Filling Shortcut Key
OPERATION
0
psi
1
0
psi
1
0
psi
Right Boom Sections Off Key
Master Screen Key
Toggle Preset Target Rates Key
Automatic Mode Boost/Step % Increase Key
APPENDIX
Automatic Mode Boost/Step % Decrease Key
10
www.teejet.com
ISOBUS Job Computer : IC18 Sprayer
Main Setup Mode
The main setup menu contains six options. Each of these options either directly access settings or
additional menus.
Figure 2-7: Main Setup Screen
Home Key
Back One Screen
Forward One Screen
Up One Selection
Down One Selection
Master Screen Key
Counters
(pages 18-21)
MAIN SETUP MODE MENU STRUCTURE
|
|
|
|
|
Job Parameters
(pages 22)
Machine
(pages 23-34)
User Interface
(pages 35-36)
Communication
(pages 37)
Help
(pages 38-41)
Trip
Filling
Diagnostic
Campaign
Operation
About
Export Counters
Implement parameters – Section width
Implement
speed sensor
Flow sensor
–
Calibrations
Nozzle preset setup
Regulation parameters
Alarm configurations
OEM
– Sensor presence
SETUP
Total
GETTING STARTED
|
OVERVIEW
The table below outlines the additional menus and directs you to the setup pages for further information.
Implement parameters
Valve setup
Tank setup
The OEM setup menu is password protected and the settings
in this menu are directly related to the fitted OEM equipment.
Refer to the IC18 Sprayer/NH3 OEM Setup Manual for
information regarding OEM settings.
98-05204 R1 US
11
APPENDIX
Clear total counters
NOTE: Select functions may not be visible due to OEM settings,
available equipment or sensors.
OPERATION
Regulation details
ISOBUS Job Computer : IC18 Sprayer
Main Setup Menu Icons and Section Overviews
Figure 2-8: Enter Selection Screens
Selection
Slide Bar with Decrease One Selection
and Increase One Selection Arrows
Accept Key
Escape Key
Number Pad
Close Number Pad Key
Range Maximum
Range Minimum
Zoom In Key
OVERVIEW
Zoom Out Key
Open Number Pad Key
GETTING STARTED
Available Selections
Up One Selection
SETUP
Accept Key
Escape Key
OPERATION
Down One Selection
APPENDIX
12
www.teejet.com
ISOBUS Job Computer : IC18 Sprayer
Description
Accept Key
Accepts the new selection
Close Number Pad Key
Minimizes the number pad
Decrease One Selection Arrow
Decreases the setting
Down One Selection Arrow
Highlights the selection below
Escape Key
Escapes without saving changes
Increase One Selection Arrow
Increases the setting
Number Pad
Use the numbers to set the selection value
Open Number Pad Key
Maximizes the number pad
Selection
Displays the current or new selection
Slider
Slide to the left to decrease or right to increase the selection
Slide Bar
Selects the setting by pressing and releasing on the slide bar or pressing
and dragging the Slider to a designated value. Range for a specific setting
is displayed on the slide bar.
Up One Selection Arrow
Highlights the selection above
Zoom In Key
Narrows slide bar range. Gray = maximum zoom level.
Zoom Out Key
Expands slide bar range. Gray = minimum zoom level.
98-05204 R1 US
13
APPENDIX
OPERATION
SETUP
GETTING STARTED
OVERVIEW
Section or Icon
ISOBUS Job Computer : IC18 Sprayer
OVERVIEW
GETTING STARTED
SETUP
OPERATION
APPENDIX
14
www.teejet.com
ISOBUS Job Computer : IC18 Sprayer
CHAPTER 3 – MAIN SETUP IN SPRAYER MODE
Main Setup Mode configures the Counters, Job Parameters, Machine, User Interface, Communication
and Help options.
NOTE:The menu structure on your display might vary from the one displayed in this User Manual
depending on the virtual terminal being used.
Figure 3-1: Main Setup Screen
Home Key
Back One Screen
Forward One Screen
Up One Option
Down One Option
|
|
|
|
|
Job Parameters
(pages 22)
Machine
(pages 23-34)
User Interface
(pages 35-36)
Communication
(pages 37)
Help
(pages 38-41)
Trip
Filling
Campaign
Operation
Total
Implement
parameters
Export Counters
Implement
speed sensor
Flow sensor
–
GETTING STARTED
Counters
(pages 18-21)
MAIN SETUP MODE MENU STRUCTURE
Diagnostic
About
–
Section width
Calibrations
Nozzle preset
setup
Alarm
configurations
Regulation
parameters
SETUP
|
OVERVIEW
Master Screen Key
98-05204 R1 US
15
APPENDIX
The OEM setup menu is password protected and the settings in this menu are directly related to the fitted OEM equipment. Refer to the IC18
Sprayer/NH3 OEM Setup Manual for information regarding OEM settings.
OPERATION
OEM
ISOBUS Job Computer : IC18 Sprayer
Main Setup Screen
OVERVIEW
GETTING STARTED
SETUP
OPERATION
NOTE: Settings are NOT automatically saved when selected. The ACCEPT KEY must be selected to save the
setting. Select the ESCAPE KEY to escape without saving settings and return to the previous menu.
To access the Main Setup screens:
1. Select IC18 SPRAYER KEY
from the Master Screen.
2. Select MAIN SETUP SCREEN KEY
from the Home Screen.
3. Select from:
►Counters – used to provide an overview of various system counters:
◄ Trip – used to display information regarding area, distance, time and amount applied.
◄ Campaign – used to display information regarding area, amount applied and time for all trips
◄ Total – used to display information regarding area, amount applied, and time for all activity
◄ Export Counters – allows counter information to be exported in HTML or CSV format
►Job Parameters – used to configure application settings including active trip counter, application rate and
nozzle type.
►Machine – used to configure machine settings:
◄ Filling – establishes the amount of material remaining in the tank and the density of that material.
◄ Operation – establishes Application Rate Step, Speed Source, and Simulated Speed
◄ Implement Parameters – establishes the Section Width, Nozzle Preset Setup and Regulation
Parameters
◄ Calibrations – establishes either manual or automatic settings of the sensors
◄ Alarm Configurations – establishes alarms for CAN Speed Source Timeout, Active Trip Count
Information mode and Tank Content Minimum
◄ OEM – The OEM setup menu is password protected and the settings in this menu are directly related
to the fitted OEM equipment. Refer to the OEM Setup Manual for information regarding OEM settings.
►User Interface – used to allow the operator to select the system virtual terminal (VT), switchbox pairing,
BoomPilot ECU pairing and soft key numbering as well as view serial numbers and ECU identification
numbers:
►Communication – used to establish the IC18's ability to communicate with an external computer:
►Help – allows the operator to choose between Diagnostics and the About screen:
◄ Diagnostic – used to troubleshoot input/output of the controller (sensor or actuator).
◄ About – used to provide information on the console such as software version, build number, etc
NOTE: The menu structure on your display might vary from the one displayed in this User Guide depending on
the virtual terminal being used. This User Guide will display all possible options.
APPENDIX
16
www.teejet.com
ISOBUS Job Computer : IC18 Sprayer
Master Screen
98-05204 R1 US
17
APPENDIX
OPERATION
SETUP
The Home Screen gives access to the IC18’s available functions: Operation Mode, Transport Mode and
Main Setup.
• To view the Home Screen, select HOME KEY
in the top right corner of any screen.
Figure 3-3: Home Screen
Home Key on Main Setup Screen
GETTING STARTED
Home Screen
OVERVIEW
The Master Screen gives access to the systems currently available on your VT.
• To view the Master Screen options, select MASTER SCREEN KEY
in bottom right corner of any
screen.
Figure 3-2: Master Screen
Master Screen Key on Main Setup Screen
ISOBUS Job Computer : IC18 Sprayer
COUNTERS
The Counters Menu provides an overview of various system counters including Trip Counters, Campaign
Counters and Total Counters. From this screen one can also Export Counters.
|
Counters
|
Job Parameters
MAIN SETUP MENU
|
Machine
|
User Interface
|
Communication
Trip
Campaign
Total
Export Counters
OVERVIEW
1. From the Main Setup Screen , select COUNTERS. Figure 3-4: Counters
2. Select from:
►Trip – used to display information regarding area,
distance, time and amount applied
►Campaign – used to display information regarding
area, amount applied and time for all trips
►Total – used to display information regarding area,
amount applied, and time for all activity
►Export Counters – allows counter information to be
exported in HTML or CSV format
GETTING STARTED
NOTE: Settings are NOT automatically saved when
selected. The ACCEPT KEY
must be selected
to save the setting. Select the ESCAPE KEY
to escape without saving settings and return to the previous menu.
SETUP
OPERATION
APPENDIX
18
www.teejet.com
|
Help
ISOBUS Job Computer : IC18 Sprayer
Trip Counters
Trip Counters displays information regarding area,
distance, time and amount applied. The trip that is active
is displayed/active on the Operations Screen.
Figure 3-5: Trip Counters Menu
Active Trip Counter
One of up to ten (10) Active Trip Counters can be selected
to view the desired trip information. The trip that is “active”
is displayed/active on the Operation Screen.
• To select the Active Trip Counter, use the number
pad or slide bar.
• To clear the Trip Counters, select TRASH CAN
KEY
. A confirmation screen will be displayed.
Figure 3-6: Confirm Counter Clearance
OVERVIEW
Distance Counter
Displays distance traveled for the selected Active Trip.
Time Counter
Displays time traveled for the selected Active Trip.
OPERATION
SETUP
GETTING STARTED
Volume Counter
Displays volume of material applied during the selected
Active Trip.
98-05204 R1 US
19
APPENDIX
Area Counter
Displays applied coverage area for the selected Active
Trip.
ISOBUS Job Computer : IC18 Sprayer
Campaign Counters
Campaign Counters display information regarding area, Figure 3-7: Campaign Counters
amount applied and time for all trips.
• To clear the Campaign Counters, select TRASH CAN
KEY
. A confirmation screen will be displayed.
Area Counter
Displays total applied coverage area for all trips.
Volume Counter
Displays total volume of material applied during all trips.
Time Counter
Displays total time traveled for all trips
Total Counters
Figure 3-8: Confirm Campaign Clearance
Total Counters displays information regarding area,
amount applied, and time for all activity. Total Counters
can only be cleared in the OEM menu.
OVERVIEW
Area Counter
Displays total applied coverage area for all trips.
GETTING STARTED
Volume Counter
Displays total volume of material applied during all trips.
Time Counter
Displays total time traveled for all trips.
SETUP
OPERATION
APPENDIX
20
www.teejet.com
Figure 3-9: Total Counters
ISOBUS Job Computer : IC18 Sprayer
Export Counters
Export Counters allows counter information to be exported Figure 3-10: Export Counters
in HTML or CSV format. HTML files can be viewed from
an internet browser. CSV files can be viewed as Excel
sheets.
• To export a HTML file, select HTML KEY
.A
confirmation screen will be displayed.
• To export a CSV file, select CSV KEY
.A
confirmation screen will be displayed.
For data transfer, an optional cable is required. Contact
your local dealer for additional information.
98-05204 R1 US
21
APPENDIX
OPERATION
SETUP
GETTING STARTED
OVERVIEW
Figure 3-11: Confirm Export Counters
ISOBUS Job Computer : IC18 Sprayer
JOB PARAMETERS
Job Parameters configures application settings. Options include Active Trip Counter, Preset Application Rates and
Nozzle.
|
Counters
MAIN SETUP MODE MENU STRUCTURE
|
Job Parameters
1. From the Main Setup Screen
PARAMETERS.
|
Machine
, select JOB
|
User Interface
|
Communication
|
Help
Figure 3-12: Job Parameters
NOTE: Settings are NOT automatically saved when
selected. The ACCEPT KEY
must be selected
to save the setting. Select the ESCAPE KEY
to escape without saving settings and return to the
previous menu.
OVERVIEW
SETUP
Preset Application Rates
Preset Application Rates define up to five (5) target rates of product being applied per hectare/acre. These
settings will set the same for all active trips. Target rates set to "0.0" will not be in included in the TOGGLE
PRESET TARGET RATE options
on the Operation Screen or Home Screen.
• To select the Application Rate, use the number pad or slide bar.
OPERATION
GETTING STARTED
Active Trip Counter
Active Trip Counter selects one of up to ten (10) active trip
counters to view the desired trip information. The trip that
is “active” is displayed/active on the Operation Screen.
• To select the Active Trip Counter, use the number
pad or slide bar.
NOTE: The selected trip counter will have all data modified (added too) when additional operations are activated.
If current trip counter is not cleared, the new data will be added to the existing data.
Nozzle
Nozzle selects the nozzle type. This setting will set the same for all active trips. The five (5) available nozzle types
are preset under Main --> Machine --> Implement Parameters --> Nozzle Preset Setup.
• To select the Nozzle type, select an option from the drop down menu or use the UP/DOWN ARROWS to
highlight the option.
APPENDIX
22
www.teejet.com
ISOBUS Job Computer : IC18 Sprayer
MACHINE
Machine configures machine settings. Options include Filling, Operation, Implement Parameters, Calibrations,
Alarm Configurations and OEM.
|
Counters
MAIN SETUP MODE MENU STRUCTURE
|
Job Parameters
|
Machine
|
User Interface
|
Communication
|
Help
Filling
Operation
Implement parameters – Section width
Implement speed sensor – Calibrations
Flow sensor
Alarm configurations
Nozzle preset setup
Regulation parameters
OEM
The OEM setup menu is password protected and the settings in this menu are directly related to the fitted OEM equipment.
98-05204 R1 US
23
GETTING STARTED
SETUP
OPERATION
NOTE: Settings are NOT automatically saved when selected. The ACCEPT KEY
must be selected to save
the setting. Select the ESCAPE KEY
to escape without saving settings and return to the previous
menu.
APPENDIX
Figure 3-13: Machine
1. From the Main Setup Screen , select MACHINE.
2. Select from:
►Filling – establishes the amount of material
remaining in the tank and the density of that
material.
►Operation – establishes Application Rate Step,
Speed Source, and Simulated Speed.
►Implement Parameters – establishes the Section
Width, Nozzle Preset Setup and Regulation
Parameters.
►Calibrations – establishes either manual or
automatic settings of the sensors.
►Alarm Configurations – establishes alarms for CAN
Speed Source Timeout, Active Trip Count Information mode and Tank Content Minimum
►OEM – The OEM setup menu is password protected and the settings in this menu are directly related to the
fitted OEM equipment. Refer to the OEM Manual for information regarding OEM settings.
OVERVIEW
ISOBUS Job Computer : IC18 Sprayer
Filling
Filling establishes the amount of material remaining in the tank and the density of that material.
Different options will be available depending on if a tank sensor is installed.
NOTE: The size of the tank is established in the OEM menu. This is the number that will repopulate when the Full
Tank Key
is pressed.
Figure 3-14: Filling
Actual Content
Actual Content displays the current volume of content in
the tank. The volume can be manually adjusted.
• To adjust the volume, use the number pad or slide
bar.
NOTE: When a tank sensor is active, the actual content
can not be changed manually.
OVERVIEW
Density
Density establishes the density of the material being
applied. It can be set to either “fertilizer” or “water”.
• To select the Density, select an option from the drop
down menu or use the UP/DOWN ARROWS to
highlight the option.
NOTE: If “Fertilizer” is selected, a Density Factor option appears.
GETTING STARTED
Density Factor
Density Factor establishes the weight per volume setting based on the type of fertilizer being used.
• To select the Density Factor, use the number pad or slide bar.
The fertilizer’s ability to flow is affected by a number of factors. These factors may vary with each batch and it may
change due to weather (humidity, etc.). In order to accommodate for this, the job computer uses a density factor
to compensate for the nature of the applied fertilizer.
SETUP
Full Tank
Full Tank returns the Actual Content volume value to the maximum volume of the tank
• To reset the Actual Content value, press the FULL TANK KEY
.
OPERATION
APPENDIX
24
www.teejet.com
ISOBUS Job Computer : IC18 Sprayer
Operation
Operation establishes Application Rate Step, Speed
Source and Simulated Speed.
Figure 3-15: Operation
Application Rate Step
Application Rate Step is the percent of increase/decrease
“boost” of the active application rate at which the product
is being applied.
• To select the percentage, use the number pad or
slide bar.
Speed Source
Speed Source selects whether to base the machine’s
speed on input from the CAN, an Implement or a
Simulated source. Selecting “Implement” will allow for
Figure 3-16: Step % Increase/Decrease
the configuration of pulses per 300 feet / 100 meters.
Cnt
5
4070 gal
1.14 ac
Selecting “Simulated” will allow for simulated speed to be
entered using the “Edit Value” option. Selecting “CAN”
allows for speed being supplied by the ISOBUS CAN
5.0
283
1 3 11
(usually from the TECU) to be used.
mph
G PA
• To select the Speed Source, select an option
from the drop down menu or use the UP/DOWN
ARROWS to highlight the option.
NOTE: If “Implement” is selected, refer to the Calibrations
section for further instructions.
OVERVIEW
28
OPERATION
SETUP
psi
98-05204 R1 US
25
APPENDIX
Simulated Speed
Simulated Speed establishes a speed to be used when
using the Simulated Speed source.
• To select the Simulated Speed, use the number pad or slide bar.
5%
GETTING STARTED
+
ISOBUS Job Computer : IC18 Sprayer
Implement Parameters
Figure 3-17: Implement parameters
Implement Parameters establishes the following:
►Section Width – sets the spraying width during
application.
►Nozzle Preset Setup – where up to five (5) sets of
nozzle options can be established to set the nozzle
type, size, low/high pressure limit, reference flow and
reference pressure.
►Regulation Parameters – where adjustments to the
valve calibration, nozzle spacing and regulations mode
can be established.
Section Width
Section Width sets the spraying width during application.
OVERVIEW
GETTING STARTED
Boom Section Width
Section Width establishes the boom sections widths for
each boom section.
NOTE: The number of boom sections available is set on
the Implement Parameters screen in the OEM
section.
• To select the Boom Section Width, use the number
pad or slide bar.
When the section widths are changed, power must be
cycled in order to update the TASC Controller on the VT.
Figure 3-18: Section Width
SETUP
One-Touch Equal Widths
One-Touch Equal Widths sets all boom section widths to
the value set for #1 Boom Section.
• To set all boom section widths, press the EQUAL SECTION WIDTH KEY
OPERATION
APPENDIX
26
www.teejet.com
.
ISOBUS Job Computer : IC18 Sprayer
Nozzle Preset Setup
Nozzle Preset Setup establishes up to five (5) sets of
nozzle options setting the nozzle type, size, low/high
pressure limit, reference flow and reference pressure.
Figure 3-19: Nozzle Preset Setup
Nozzle Preset
Each one of up to five (5) Nozzle Presets can be selected
to establish different sets of nozzle options.
• To select the Nozzle Preset set, use the number pad
or slide bar.
Size
Color
Orange
05
Brown
015
Green
06
Grey
02
Yellow
08
White
025
Purple
10
Light Blue
03
Blue
15
Light Green
04
Red
20
Black
SETUP
Color
01
OPERATION
When “General” nozzle type is selected and a establised
nozzle size is selected, the Low Pressure Limit, High
Pressure Limit, Reference Flow and Reference Pressure
fields will be automatically set with the standard settings
for the specific nozzle chosen. These setting can be
manually adjusted.
98-05204 R1 US
27
APPENDIX
Size
GETTING STARTED
Nozzle Size
Nozzle Size sets the nozzle from a list of established sizes (see chart below) or from a optional user tip.
• To select the Nozzle Size, select an option from the drop down menu or use the UP/DOWN ARROWS to
highlight the option.
Figure 3-20: Nozzle Size on the Operating Screen
Established Nozzle Sizes and Colors
OVERVIEW
Nozzle Type
Nozzle Type sets whether the nozzle’s size will be
selected from a general section of established tips or a
optional user tip.
• To select the Nozzle Type, select an option from the drop down menu or use the UP/DOWN ARROWS to
highlight the option.
ISOBUS Job Computer : IC18 Sprayer
Low Pressure Limit
Low Pressure Limit establishes the limit for the lowest allowed operating pressure for the selected nozzle type.
• To select the Low Pressure Limit, use the number pad or slide bar.
High Pressure Limit
High Pressure Limit establishes the limit for the highest
allowed operating pressure for the selected nozzle type.
• To select the High Pressure Limit, use the number
pad or slide bar.
Figure 3-21: Recommended Pressure Range bar and
High Pressure Limit on the Operating
Screen
Reference Flow
Reference Flow establishes the value for the volume
applied over a specific time (GPM or LPM).
• To select the Reference Flow, use the number pad or
slide bar.
OVERVIEW
GETTING STARTED
Reference Pressure
Reference Pressure establishes the pressure value at
which the application rate is true (ISO=2 bar).
• To select the Reference Pressure, use the number
pad or slide bar.
IMPORTANT! Always refer to the nozzle pressure values
recommended by the supplier when setting the
nozzle pressure.
SETUP
Factory Settings
Factory Settings resets all nozzle settings to the default
settings for the selected nozzle size and type.
• To reset the Factory Settings, select FACTORY
SETTINGS KEY
. A confirmation screen will be
displayed.
OPERATION
APPENDIX
28
www.teejet.com
Figure 3-22: Confirm Factory Settings
ISOBUS Job Computer : IC18 Sprayer
Valve Calibration, Fine
Fine regulation value calibration allows you to regulate the setting of the regulating valve to accommodate
different application needs. Operating conditions may necessitate a higher or lower response setting for the
regulating valve. This digit adjsuts the setting for the fine tune adjustment in relation to a small percentage close to
the target application rate.
►If the system is too slow in finding the correct rate, the values should be increased.
►If the system is too unstable, the values should be decreased.
• To select the Valve Calibration, Fine, use the number pad or slide bar.
If your system is plumbed in a bypass mode, the valve setting number of 5 works very well in most applications.
98-05204 R1 US
29
GETTING STARTED
SETUP
Valve Calibration, Rough
Rough regulation value calibration allows you to regulate
the setting of the regulating valve to accommodate
different application needs. Operating conditions may
necessitate a higher or lower response setting for the
regulating valve. This value adjusts the setting for coarse
adjustments in relation to a large percentage outside of
the target application rate
►If the system is too slow in finding the correct rate, the values should be increased.
►If the system is too unstable, the values should be decreased.
• To select the Valve Calibration, Rough, use the number pad or slide bar.
If your system is plumbed in a bypass mode, the valve setting number of 9 works very well in most applications
If your system is plumbed in a throttling mode, start with a valve setting number of 3 and adjust the number
according to your application requirements. Low flow situations will require a slower response time. Adjusting
agitation volumes to accommodate the regulating valve to work in a more fully open position allows for a faster
response time, with little to no searching.
NOTE: This setting value can be adjusted to optimize system performance. If you notice that the valve seems to
“search” for the programmed application rate by cycling the pressure up and down continuously, reduce
the number until the “searching” is minimized or eliminated. Conversely, a higher number will increase the
valve response time and “speed up” the rate of adjustment.
OVERVIEW
Figure 3-23: Regulation Parameters
OPERATION
Regulation Parameters establishes adjustments to the
valve calibrations, nozzle spacing and regulations mode.
NOTE: Adjusting the Valve Calibration settings involves
significant changes and adjustments should
therefore be made in small steps.
APPENDIX
Regulation Parameters
ISOBUS Job Computer : IC18 Sprayer
If your system is plumbed in a throttling mode, start with a valve setting number of 3 and adjust the number
according to your application requirements. Low flow situations will require a slower response time. Adjusting
agitation volumes to accommodate the regulating valve to work in a more fully open position allows for a faster
response time, with little to no searching.
NOTE: This setting value can be adjusted to optimize system performance. If you notice that the valve seems to
“search” for the programmed application rate by cycling the pressure up and down continuously, reduce
the number until the “searching” is minimized or eliminated. Conversely, a higher number will increase the
valve response time and “speed up” the rate of adjustment.
Nozzle Spacing
Nozzle Spacing establishes the distance between the nozzles on the boom.
• To select the Nozzle Spacing, use the number pad or slide bar.
Regulation Mode
Regulation Mode determines if the rate control is pressure based or flow based.
• To select the Regulation Mode, select an option from the drop down menu or use the UP/DOWN ARROWS
to highlight the option.
OVERVIEW
GETTING STARTED
SETUP
OPERATION
APPENDIX
30
www.teejet.com
ISOBUS Job Computer : IC18 Sprayer
Calibrations
Calibrations establishes either manual or automatic
settings of the sensors.
NOTE: For specific calibration options to appear, a
specific sensor needs to be installed. Sensor
availability is activated on the Sensor Presence
screen in the OEM section.
Figure 3-24: Calibrations
Implement Speed Sensor
The Implement Speed Sensor establishes the wheel
pulses over a specified distance. This value can be
established manually or calibrated automatically.
OVERVIEW
Manual Calibration
Manual calibration establishes the pulses based on a user Figure 3-25: Implement Speed Sensor
entered value.
• To select the Pulses per Distance, use the number
pad or slide bar.
98-05204 R1 US
31
APPENDIX
OPERATION
SETUP
GETTING STARTED
Automatic Calibration
Automatic calibration establishes the pulses using the
automatic calibration function.
• To calibrate the pulses per distance, select
CALIBRATION KEY
.
• Follow the series of instructions displayed.
• Select the ACCEPT KEY
to complete the
calibration
The counted wheel pulses will be displayed during the
automatic calibration.
ISOBUS Job Computer : IC18 Sprayer
Flow Sensor
The Flow Sensor establishes the pulses per gallon/liter.
This value can be established manually or calibrated
automatically.
Figure 3-26: Flow Sensor
Manual Calibration
Manual calibration establishes the calibration and limits
based on user entered values.
• To select the Flow Meter Calibration, use the number
pad or slide bar.
• To select the Low Limit, use the number pad or slide
bar.
• To select the High Limit, use the number pad or slide
bar.
OVERVIEW
GETTING STARTED
Automatic Calibration
If the number of pulses per gallon/liter for the flow meter is not known or to make sure the value is correct,
automatic calibration establishes the calibration and limits.
• To calibrate the flow sensor, select CALIBRATION KEY
.
• Follow the series of instructions displayed.
• Select the ACCEPT KEY
to complete the calibration
The pulses counted will be displayed during the automatic calibration.
An option to enter a Collected Volume is displayed if there is no calculated volume.
• To enter the Collected Volume, use the number pad or slide bar.
SETUP
OPERATION
APPENDIX
32
www.teejet.com
ISOBUS Job Computer : IC18 Sprayer
Alarm Configurations
Alarm Configurations establishes alarms on or off as well Figure 3-27: Alarm Configurations
as sets their trigger level.
CAN Speed Source Timeout
CAN Speed Source Timeout establishes how long the
system can operate after the CAN speed source input is
lost before the alarm is triggered.
• To select the CAN Speed Source Timeout time, use
the number pad or slide bar.
98-05204 R1 US
33
GETTING STARTED
APPENDIX
OPERATION
SETUP
Tank Content Minimum
Tank Content Minimum establishes the minimum volume level at which an alarm will sound. Without a Tank
Sensor, the minimum is determined by calculating the difference between the established actual tank content
volume and the calculated applied content volume. With a Tank Sensor, the minimum is directly related to the
sensor reading.
• To select the minimum volume, use the number pad or slide bar.
OVERVIEW
Active Trip Count Information
Active Trip Count Information sets the associated alarm
to on or off. This alarm is only displayed at powered up. It
tells the user which trip counter is active.
• To select the Active Trip Count Information mode, select an option from the drop down menu or use the UP/
DOWN ARROWS to highlight the option.
ISOBUS Job Computer : IC18 Sprayer
OEM
OVERVIEW
GETTING STARTED
SETUP
The OEM setup menu is password protected and the settings in this menu are directly related to the fitted OEM
equipment. To obtain an access code, contact your local dealer or TeeJet Technologies Customer Service.
To access the OEM screens:
Figure 3-28: Machine to OEM
1. From the Main Setup Screen , select MACHINE.
2. Select OEM.
3. Select the Access Code Entry Box to the right of the
menu option.
4. Use the number pad or slide bar to enter the access
code.
5. Select the ACCEPT KEY
to complete the unlock
process
6. Select from:
►Sensor presence – used to establish sensors for
Flow, Liquid Pressure, Fill Flow and the Tank
►Implement parameters – used to establish the
Sprayer Mode, Number of Sections and Circulation
►Valve setup – used to establish the Regulation
Valve Type, Section Valve Behavior and Section
Valve Type
►Tank setup – used to establish maximum and
minimum tank content, Auto Filling mode and Auto
Filling Offset value
►Regulation details – used to adjust the control of
the regulation valve
►Clear total counters – used to delete the Total
Figure 3-29: OEM Unlock
Count system counter for Area, Volume and Time
back to the default settings
OPERATION
NOTE: Settings are NOT automatically saved when
selected. The ACCEPT KEY
must be selected
to save the setting. Select the ESCAPE KEY
to escape without saving settings and return to the
previous menu. OEM
APPENDIX
34
www.teejet.com
ISOBUS Job Computer : IC18 Sprayer
USER INTERFACE
User Interface allows the operator to select the system virtual terminal (VT), switchbox pairing, BoomPilot ECU
pairing and soft key numbering as well as view serial numbers and ECU identification number.
|
Counters
MAIN SETUP MODE MENU STRUCTURE
|
Job Parameters
1. From the Main Setup Screen
select USER INTERFACE.
|
Machine
,
|
User Interface
|
Communication
|
Help
Figure 3-30: User Interface
NOTE: Settings are NOT automatically saved when
selected. The ACCEPT KEY
must be selected
to save the setting. Select the ESCAPE KEY
to escape without saving settings and return to the
previous menu.
Pair with BoomPilot ECU
The pairing of a BoomPilot ECU can be set to be done automatically, not at all or to a specific BoomPilot ECU ID
number on the CAN network.
98-05204 R1 US
35
OPERATION
Pair with Switchbox
The pairing of a switchbox can be set to be done automatically, not at all or to a specific switchbox ECU ID
number on the CAN network.
• To set the Switchbox pairing, select an option from the drop down menu or use the UP/DOWN ARROWS to
highlight the option.
APPENDIX
This IC18
Displays IC18's serial number and associated ECU identification number.
SETUP
GETTING STARTED
OVERVIEW
Use Preferred VT
Use Preferred VT sets the virtual terminal preference to
either on or off. If “On” is selected, the preferred VT will
be used. If “Off” is selected, the system will arbitrarily
select which VT to use (if more than one VT is available
on the ISOBUS CAN).
NOTE: This should always be set to "off" unless another VT is on the CAN bus.
• To set the Use Preferred VT mode, select an option from the drop down menu or use the UP/DOWN
ARROWS to highlight the option.
ISOBUS Job Computer : IC18 Sprayer
• To set the BoomPilot ECU pairing, select an option from the drop down menu or use the UP/DOWN
ARROWS to highlight the option.
OVERVIEW
Currently Paired With Information
Displays the current ECU ID numbers for a paired switchbox or BoomPilot ECU.
• If no switchbox or BoomPilot ECU is on the system, "none" will be shown.
• If a specific switchbox or BoomPilot ECU has been chosen to be paired with and it is not available on the
system, "none" will be shown.
Figure 3-31: Sprayer Number
Show Number on Soft Key
Show Number on Soft Key establishes if a user assigned
identification number will be visible on the Master Screen,
Home Screen and Operation Screen.
• To set the Soft Key Number mode, select an option
from the drop down menu or use the UP/DOWN
ARROWS to highlight the option.
NOTE: Typically used only if more than one (1) IC18 ECU
is on the CAN bus.
If “Yes” is selected, a Sprayer Number (FI) option
appears.
GETTING STARTED
Sprayer Number (FI)
Sprayer Number is the identification number referring
specifically to the IC18 ECU referenced under the "This
IC18" information row on the User Interface screen.
• To set the Sprayer Number, use the number pad or
slide bar.
SETUP
OPERATION
APPENDIX
36
www.teejet.com
ISOBUS Job Computer : IC18 Sprayer
COMMUNICATION
Communication establishes the IC18's ability to communicate with an external computer.
MAIN SETUP MODE MENU STRUCTURE
|
Communication
|
Help
OVERVIEW
Figure 3-32: Communication
GETTING STARTED
,
|
User Interface
SETUP
1. From the Main Setup Screen
select COMMUNICATION.
|
Machine
OPERATION
|
Job Parameters
98-05204 R1 US
37
APPENDIX
|
Counters
ISOBUS Job Computer : IC18 Sprayer
HELP
The Help menu allows the operator to choose between Diagnostics and the display of information about serial
number, CAN BUS information, etc. These menus are typically accessed upon Customer Service personnel
request only.
|
Counters
MAIN SETUP MODE MENU STRUCTURE
|
Job Parameters
|
Machine
|
User Interface
|
Communication
|
Help
Diagnostic
About
1. From the Main Setup Screen , select HELP.
2. Select from:
►Diagnostic – used to troubleshoot input/output of
the controller (sensor or actuator).
►About – provides information on the console such
as software version, build number, etc.
OVERVIEW
NOTE: Settings are NOT automatically saved when
selected. The ACCEPT KEY
must be selected
to save the setting. Select the ESCAPE KEY
to escape without saving settings and return to the
previous menu.
GETTING STARTED
SETUP
OPERATION
APPENDIX
38
www.teejet.com
Figure 3-33: Help
ISOBUS Job Computer : IC18 Sprayer
Diagnostic
Figure 3-34: Diagnostic
Diagnostic is used to troubleshoot input/output of the
controller (sensor or actuator).
►Test Input – displays the input high and low values on
the installed sensors.
►Test Output – sets the Liquid Valve PWM Dutycycle
percentage as well as if Liquid Valve Direction, Master
Valve, Fill Valve and Section Valves 1-9 are on or off.
►VT – provides information regarding the virtual terminal
controller.
►TECU – provides information regarding the TECU.
Test Input
OPERATION
SETUP
GETTING STARTED
OVERVIEW
Figure 3-35: Test Input
98-05204 R1 US
39
APPENDIX
Test Input displays the input high and low values on the
installed sensors.
• To reset the sensors to "0",
select TRASH CAN KEY
.
ISOBUS Job Computer : IC18 Sprayer
Test Output
Test Output sets the Liquid Valve PWM Dutycycle
percentage as well as if Liquid Valve Direction, Master
Valve, Fill Valve and Section Valves 1-9 are on or off.
Figure 3-36: Test Output
Liquid Valve PWM Dutycycle
Liquid Valve PWM Dutycycle is used to test the regulating
valve at different percentages of duty cycle.
• To set the Liquid Valve PWM Dutycycle, use the
number pad or slide bar.
Liquid Valve Direction
Liquid Valve Direction is used to verify the option of the
Liquid valve direction is correct to a specific duty cycle.
• Set the Liquid Valve PWM dutycycle to the
percentage to be tested.
• Change the Liquid valve direction to "on" and the
liquid valve will open at the specific dutycycle.
• Change it back to off and the valve will close.
OVERVIEW
GETTING STARTED
Master Valve
Master Valve is used to test if the Master Valve is
operating correctly. If you change the setting to "on", the
valve will open, change it to "off" and the valve will close.
• To set the Master Valve, select an option from the
drop down menu or use the UP/DOWN ARROWS to
highlight the option.
SETUP
Section Valves
Section Valves is used to test if the section Valve is operating correctly. If you change the setting to "on", the
valve will open, change it to "off" and the valve will close.
• To set the Section Valves, select an option from the drop down menu or use the UP/DOWN ARROWS to
highlight the option.
OPERATION
APPENDIX
40
www.teejet.com
ISOBUS Job Computer : IC18 Sprayer
VT Data
Figure 3-37: VT Data
The Virtual Terminal (VT) menu provides information
regarding the virtual terminal controller (i.e., address
version, etc.).
• If more terminals/controllers are used, switch
between these by pressing the GO TO NEXT VT
KEY
.
• Press the DELETE OBJECT POOL KEY
to delete
saved information on the VT. This forces the VT
to upload all information from the IC18 on the next
power cycle.
NOTE: Restart the IC18 Job Computer to implement and
display changes.
TECU
Figure 3-38: TECU
SETUP
Figure 3-39: About
OPERATION
The About screen provides information on the IC18 such
as software version, build number, etc. This information
may become useful in case of technical support.
98-05204 R1 US
41
APPENDIX
About
GETTING STARTED
OVERVIEW
The TECU is a control unit, residing on the tractor, that
performs basic functions such as power handling, speed
info, etc. The TECU data are displayed on this page.
ISOBUS Job Computer : IC18 Sprayer
OVERVIEW
GETTING STARTED
SETUP
OPERATION
APPENDIX
42
www.teejet.com
ISOBUS Job Computer : IC18 Sprayer
CHAPTER 4 – OPERATION MODE
The Operation Screen accesses the working aspects of the IC18 including boom section control, rate
control and trip/count/application information.
NOTE: Settings are automatically saved when selected.
NOTE:The menu structure on your display might vary from the one displayed in this User Manual
depending on the virtual terminal being used.
Auto/Manual Key on Operation Screen
5
4070 gal
1.14 ac
+
mph
1 3 11
283
G PA
SETUP
5.2
5%
OPERATION
Cnt
0
psi
1
98-05204 R1 US
43
APPENDIX
Figure 4-1: Auto/Manual Key on Home Screen
GETTING STARTED
Automatic regulation mode will automatically adjust the application rate based on the current speed in reference
to the target rate. The target rate can be adjusted using the Boost/Step % Increase/Decrease Keys
on
the Operation Screen. Preset Application Rates define up to five (5) target rates for product being applied per
hectare/acre. These can be toggled using the Toggle Preset Target Rate Key
on the Operation Screen or
Home Screen.
Manual regulation mode will retain an established regulation valve setting regardless of speed. The regulation
valve setting can be adjusted using the Regulation Valve Open/Close Keys
on the Operation Screen.
If a switchbox is being used to control the boom sections, automatic or manual regulation mode can be set on the
Operation Screen.
When using the IC18, not a switchbox, for boom section control, automatic or manual regulation mode needs to
be established on the Home Screen before entering Operation Mode.
1. On the Home Screen
or Operation Screen , establish Automatic Operation Mode or Manual Operation
Mode by pressing the AUTO/MANUAL KEY
so that the green dot is on AUTO (automatic) or the hand
(manual) accordingly.
OVERVIEW
AUTOMATIC OR MANUAL REGULATION MODE
ISOBUS Job Computer : IC18 Sprayer
OPERATION MODE OVERVIEW
Information on the Operation screen will vary depending on the parameters set by the user and the OEM.
Figure 4-2: Operation Mode Screen Overview
Applied Area
Applied Volume
Active Trip Count Number
Alert Warning
Cnt
5
Speed/Application Information
5.2
Remaining Tank Contents
mph
Density
Flow Based or Pressure Based
4070 gal
Cnt
Target Rate Indicator
Application Rate
Target Rate Percentage Increase/Decrease
1.14 ac
5
5.2
1 3 11
mph
4 0 7 0+ g a5 %l
2 8 35
Cnt
G PA
50.0
1 3 11
mph
Boom Sections
Nozzle Type
Recommended Pressure Range
1.14 ac
+
5%
4070 gal
1.14 ac
283
+
5%
283
G PA
1 3 11
G PA
0
psi
1
Current Working Pressure
0
psi
1
OVERVIEW
Current Pressure Rate
ECU ID Number
0
psi
NH3 Mode Active
Auto/Manual Mode Key
GETTING STARTED
Cnt
5
5.2
mph
4070 gal
Cnt
Manual Mode Regulation Valve Open Key
(flow and pressure will increase)
1.14 ac
5
5.2
1 3 11
mph
4 0 7 0+ g a5 %l
2 8 35
Cnt
G PA
50.0
1 3 11
SETUP
mph
1.14 ac
+
5%
4070 gal
283
G PA
1 3 11
1.14 ac
+
5%
283
G PA
Manual Mode Regulation Valve Close Key
(flow and pressure will decrease)
Home Key
Next Page Key
Start/Stop Key
Left Boom Sections On Key
Master Stop Key
Left Boom Sections Off Key
Information Key
Right Boom Sections On Key
Tank Filling Shortcut Key
OPERATION
0
psi
1
0
psi
1
0
psi
Right Boom Sections Off Key
Master Screen Key
Toggle Preset Target Rates Key
Automatic Mode Boost/Step % Increase Key
APPENDIX
Automatic Mode Boost/Step % Decrease Key
44
www.teejet.com
ISOBUS Job Computer : IC18 Sprayer
Keys Descriptions
Description
Home Key
Press to return to the Home Screen
Start/Stop Key
Press to start or stop application
Information Key
Press to toggle between display modes
Boost/Step
Percentage
Increase/
Decrease Keys
Press to establish the required boost percentage step, i.e. the step
size, at which the application rate is to increase/decrease with the boost
function
Toggle Preset
Target Rates
Key
Press to toggle between established target application rates
Auto/Manual
Key
Press to toggle between automatic and manual application modes.
Automatic regulation mode will automatically adjust the application rate based on the
current speed in reference to the target rate.
Manual regulation mode will retain an established regulation valve setting regardless
of speed.
Tank Filling
Shortcut Key
Press for one-press access to the Tank Filling setup screen
Master Stop Key Press to stop all application, close all regulation valves and change to manual
regulation mode
SETUP
Boom
Sections
On/Off
Keys
Press to toggle between soft key options
Press to turn on sections to left , turn off sections from left
right
or turn off sections from right
, turn on sections to
OPERATION
Next Page Key
OVERVIEW
to open the regulation valve
to close the regulation valve
GETTING STARTED
Manual Mode
Press
Regulation Valve Press
Open Keys
98-05204 R1 US
45
APPENDIX
Icon
ISOBUS Job Computer : IC18 Sprayer
Section and Icon Descriptions
Section or Icon
Description
Job Information
This information bar displays the active count number,
applied volume and applied area
Cnt
Count Number
Displays the current active trip or job number
Applied Volume
Displays volume applied for the selected count number
Applied Area
Displays applied area for the selected count number
1
0 gal
0.00 ac
OVERVIEW
Speed/Application
Information
Displays vehicle speed or volume applied per minute or projected area per hour to
be covered or projected total area remaining to be covered depending upon which
view is active.
The Information Key toggles
between display modes.
Remaining Tank
Contents
Displays the remaining tank content
NOTE: If no tank sensor is fitted or the contents are not entered in the
Tank Filling Menu prior to spraying, Tank Contents may not
display the correct amount.
Application Rate
Displays the actual application rate per hectare/acre
NOTE: When the Master is “On” the actual application rate per hectare/acre will
be displayed. When the Master is “Off” the target rate is displayed and the
TARGET RATE ICON
appears
GETTING STARTED
Target Rate
Percentage
Increase/
Decrease
Displays boost percentage step, i.e. the step size, at which the
application rate is to increase/decrease with the boost function
SETUP
Alarm
Displayed if an alarm condition is active
Flow Based or Pressure
Based Icons
These symbols will only appear if both a flow sensor and a pressure sensor are
installed.
Flow Based - displayed if a regulation is based on flow
Pressure Based - displayed if regulation is based on pressure.
OPERATION
Density
APPENDIX
46
D
www.teejet.com
Displays a “D” to the left of the tank icon if the density is set to “Fertilizer” instead of
water.
ISOBUS Job Computer : IC18 Sprayer
Section or Icon
Description
Boom Sections
Displays the active
and inactive
boom sections as well as if
they are on
(spray is blue) or off
(spray is gray).
NOTE: The color on the boom sections indicates
the color of the selected nozzle type.
Circulation SC
If Circulation is installed and selected in the OEM Menu, “SC” (Semi Circulation) or
“CC” (Full Circulation) will be displayed.
Displays if the unit is in NH3 mode.
Sprayer ID Number
Displays the soft key number assigned to the displayed IC18 ECU.
Nozzle Information
This information section displays the nozzle type,
recommended pressure range, current working
pressure and high pressure limit.
28
Nozzle Type
Displays the selected nozzle type
Recommended
Pressure Range
Displays the recommended pressure range for the selected
nozzle (the green area indicates the pressure range). The
pressure range will change depending upon the selected
nozzle, working speed, etc.
IMPORTANT! ALWAYS REFER TO THE RECOMMENDED PRESSURE RANGE
AS FAILURE TO DO SO MAY RESULT IN UNEVEN SPRAY PATTERNS.
Current Working
Pressure
Displays the current working pressure
NOTE: This pressure range should not exceed
the recommended pressure range.
IMPORTANT! ALWAYS REFER TO THE RECOMMENDED NOZZLE PRESSURE
VALUES WHEN SETTING NOZZLE PRESSURE.
Current Pressure Displays the current pressure to the nozzle
Rate
28
OPERATION
psi
OVERVIEW
psi
GETTING STARTED
NH3
SETUP
NH3 Mode Active
98-05204 R1 US
47
APPENDIX
CC
ISOBUS Job Computer : IC18 Sprayer
Master Screen
The Master Screen gives access to the systems currently available on your VT.
• To view the Master Screen options, select MASTER SCREEN KEY
in bottom right corner of any
screen.
Figure 4-3: Master Screen
Master Screen Key on Operation Mode Screen
Cnt
1
0.0
mph
0 gal
1 3 11
0.00 ac
0
G PA
0
psi
OVERVIEW
Home Screen
GETTING STARTED
The Home Screen gives access to the IC18’s available functions: Operation Mode, Transport Mode and
Main Setup.
• To view the Home Screen, select HOME KEY
in the top right corner of any screen.
Figure 4-4: Home Screen
Home Key on Operation Mode Screen
Cnt
1
0.0
mph
0 gal
1 3 11
0.00 ac
0
G PA
SETUP
OPERATION
0
psi
APPENDIX
48
www.teejet.com
ISOBUS Job Computer : IC18 Sprayer
APPLICATION RATE OPTIONS
Target Rate Percentage Increase/Decrease
Figure 4-5: Target Rate Percentage Increase/
Target Rate Percentage Increase/Decrease Keys
Decrease
increase/decrease the application target rate per the
Cnt
1
0 gal
0.00 ac
established percentage set in the Machine Operation
setup screen under Application Rate Step. Automatic
regulation mode will automatically adjust the application
0.0
25
1 3 11
rate based on the current speed in reference to the
mph
G PA
target rate. Preset Application Rates define up to five (5)
target rates of product being applied per hectare/acre.
These can be toggled using the Toggle Preset Target
Rate Key
on the Operation Screen or Home Screen.
• To adjust the Target Rate, press the BOOST/STEP %
INCREASE/DECREASE KEYS
.
0
+
5%
psi
Regulation Valve
Manual Open/Close
SETUP
GETTING STARTED
OVERVIEW
Figure 4-6: Regulation Valve Manual Open/Close
The regulation valve setting can be adjusted using
Cnt
1
0 gal
0.00 ac
the Regulation Valve Open/Close Keys
on the
Operation Screen. Manual regulation mode will retain an
established regulation valve setting regardless of speed.
0.0
0
1 3 11
mph
G PA
• To adjust the regulation valve, press the
REGULATION VALVE OPEN/CLOSE KEYS
.
0
98-05204 R1 US
49
APPENDIX
OPERATION
psi
ISOBUS Job Computer : IC18 Sprayer
Target Rate
Preset Application Rates define up to five (5) target rates of product being applied per hectare/acre. These
settings will set the same for all active trips. Target rates set to “0.0” will not be included in the toggle preset target
rate options
on the Operation Screen or Home Screen.
If a switchbox is being used to control the boom sections, current target application rate can be set on the
Operation Screen.
When a switchbox is not connected to the system current target application rate needs to be established on the
Home Screen before entering Operation Mode.
With Switchbox
• To toggle between Target Application Rates, press
the TOGGLE PRESET TARGET RATE KEY
.
Figure 4-7: Target Application Rate
Cnt
1
470 gal
1.14 ac
+
5.0
mph
1 3 11
42
G PA
OVERVIEW
0
psi
GETTING STARTED
Without Switchbox
• To toggle between Target Application Rates, press
the TOGGLE PRESET TARGET RATE KEY
.
SETUP
OPERATION
APPENDIX
50
www.teejet.com
5%
Figure 4-8: Target Application Rate
ISOBUS Job Computer : IC18 Sprayer
Orange
015
Green
02
Yellow
025
Purple
03
Blue
04
Red
05
Brown
06
Grey
08
White
10
Light Blue
15
Light Green
20
Black
1
0.0
mph
0 gal
1 3 11
0.00 ac
0
G PA
0
psi
OVERVIEW
01
Cnt
GETTING STARTED
Color
Figure 4-9: Boom Sections
SETUP
Size
(spray
OPERATION
Established Nozzle
boom sections as well as if they are on
98-05204 R1 US
51
APPENDIX
BOOM SECTIONS
Boom Sections displays the active
and inactive
is blue) or off
(spray is gray).
The color on the boom sections indicates the color of the
selected nozzle type.
ISOBUS Job Computer : IC18 Sprayer
On/Off Sections from the Left or Right
When a switchbox is not connected for boom section control, booms sections are controlled using the Boom
Sections On/Off Keys.
Without Switchbox
Figure 4-10: Left Off
• To adjust the sections on the left, press the LEFT
Cnt
1
0 gal
BOOM SECTIONS ON/OFF KEYS
.
• To adjust the sections on the right, press the RIGHT
0.0
1 3 11
BOOM SECTIONS ON/OFF KEYS
.
mph
0.00 ac
16.5
G PA
With Switchbox
If a switchbox is being used to control the boom sections,
boom sections will be controlled by the switchbox.
Figure 4-12: Operations Screen With Switchbox
Cnt
1
0.0
OVERVIEW
mph
0 gal
1 3 11
Cnt
1
0.0
mph
0.00 ac
0 gal
0
psi
1 3 11
0.00 ac
16.5
G PA
0
G PA
0
psi
Figure 4-11: Right Off
GETTING STARTED
Cnt
0
psi
1
0.0
mph
0 gal
0.00 ac
16.5
1 3 11
Cnt
G PA
1
SETUP
0.0
mph
0 gal
0
psi
1 3 11
0.00 ac
16.5
G PA
OPERATION
0
psi
APPENDIX
52
www.teejet.com
ISOBUS Job Computer : IC18 Sprayer
Start/Stop Application
When a switchbox is not connected for boom section control, starting/stopping application is controlled using the
Start/Stop Key.
Without Switchbox
• To start or stop the application, press the START/
STOP KEY
.
Figure 4-13: Spraying Stopped
Cnt
5.0
With Switchbox
mph
If a switchbox is being used to control the boom sections,
starting/stopping application will be controlled by the
switchbox.
Figure 4-15: Operations Screen With Switchbox
0.00 ac
0
25
G PA
psi
Figure 4-14: Spraying Started
Cnt
1
5.0
0
mph
20 gal
1 3 11
OVERVIEW
1 3 11
G PA
0.25 ac
27.8
G PA
GETTING STARTED
mph
25
1 3 11
psi
38
psi
SETUP
0.0
0 gal
0.25 ac
OPERATION
1
20 gal
98-05204 R1 US
53
APPENDIX
Cnt
1
ISOBUS Job Computer : IC18 Sprayer
Master Stop Key
Master Stop Key is used to stop all application, close all Figure 4-16: Spraying In Progress
Cnt
1
20 gal
0.25 ac
regulation valves and change to manual regulation mode.
• To stop all application, close all regulation valves and
5.0
26.7
change to manual regulation mode, press the STOP
1 3 11
mph
G PA
KEY
.
This is designed to be like an emergency stop button.
With Switchbox
If a switchbox is being used to control the boom sections,
the Master Stop Key will override the Master Switch
on the switchbox and turn off any boom application in
progress.
38
psi
Figure 4-17: Master Stop Pressed
Cnt
1
5.0
OVERVIEW
mph
20 gal
1 3 11
0.25 ac
25
G PA
GETTING STARTED
0
psi
SETUP
OPERATION
APPENDIX
54
www.teejet.com
ISOBUS Job Computer : IC18 Sprayer
INFORMATION KEY
Information Key toggles the Speed/Application Information section on the Operation Screen between the display
modes.
• Vehicle speed
• Volume applied per minute
• Projected area per hour to be covered based on current speed, target rate and tank level
• Projected total area remaining to be covered based on current target rate and current tank level
Figure 4-18: Information Key
0 gal
0 gal
1
ac/h
Cnt
G PA
psi
0 gal
0.0
0
1 3 11 0
GPM
Cnt
0.00 ac
0.00 ac
0
1 3 11
1
0.0
ac
OVERVIEW
1
0.0
Volume applied per minute
Projected total area remaining
G PA
GETTING STARTED
Cnt
Projected area per hour
0
1 3 11
mph
G PAp0s i
0 gal
0.00 ac
1 3 11 0
psi
SETUP
0.0
0.00 ac
0
G PA
OPERATION
Vehicle speed
1
0
psi
98-05204 R1 US
55
APPENDIX
Cnt
ISOBUS Job Computer : IC18 Sprayer
TRANSPORT MODE
While in Transport Mode, all operation functions are locked off and cannot be activated. Transport Mode displays
the speed in analogue mode.
Figure 4-19: Transport Mode
Home Key
►Gives access to the IC18’s available functions: Operation Mode,
Transport Mode and Main Setup
Speedometer
Master Screen Key
►Gives access to the systems currently available on your VT
OVERVIEW
GETTING STARTED
SETUP
OPERATION
APPENDIX
56
www.teejet.com
ISOBUS Job Computer : IC18 Sprayer
APPENDIX A - FACTORY SETTINGS & RANGES
JOB PARAMETERS
Description
Factory Setting
Range
User Setting
Active Trip Counter
1
1 - 10
1
2
3
4
5
6
7
8
9
10
#2
#4
Preset Application Rate #5
#5
GETTING STARTED
#3
Preset Application Rate #4
Nozzle
OVERVIEW
#1
Established
under
Machine-->
Implement
Parameters-->
Nozzle Preset
Setup
SETUP
Preset Application Rate #3
0.0 - 700.6 (US)
0.0 - 6553
0.0 - 583.4 (UK)
OPERATION
Preset Application Rate #2
0.0 GPA (US)
0.0 l/ha
0.0 GPA (UK)
98-05204 R1 US
57
APPENDIX
Preset Application Rate #1
ISOBUS Job Computer : IC18 Sprayer
MACHINE
Tank Filling
Description
Factory Setting
Range/Options
Actual Content
0 lbN (US)
0 kgN
0 lbN (UK)
0 - 12000
0 - 5443
0 - 12000
Density
Water
Water
Fertilizer
Density Factor
6.68 Lb/Gal (US)
0.80 kg/l
8.02 Lb/Gal (UK)
6.68 - 16.69 (US)
0.80 - 2.00
8.02 - 20.04 (UK)
Description
Factory Setting
Range/Options
Application Rate Step
5%
1 - 20
Speed Source
CAN
CAN
Implement
Simulated
Simulated Speed
0.0 mile/h / km/h
0.0 - 99.9
Description
Factory Setting
Range
Valve Calibration, Rough
19
1 - 19
Valve Calibration, Fine
9
1-9
Nozzle Spacing
19.7 in
50 cm
1.0 - 787.4
1.0 - 1999.9
Regulation Mode
Flow Based
Pressure Based
Flow Based
User Setting
Operation
User Setting
OVERVIEW
GETTING STARTED
Implement Parameters
Regulation Parameters
SETUP
OPERATION
APPENDIX
58
www.teejet.com
User Setting
ISOBUS Job Computer : IC18 Sprayer
Section Width
Description
Factory Setting
Range
Section Width
118 in. / 300 cm
1 - 9999
Description
Factory Setting
Range/Options
Nozzle Preset
1
1-5
Nozzle Type
General
General
User Tip
Nozzle Size
025 (purple)
01 Orange
015 Green
02 Yellow
025 Purple
03 Blue
04 Red
05 Brown
06 Grey
08 White
10 Light Blue
15 Light Green
20 Black
Low Pressure Limit
14 psi
1.0 bar
0 - 369
0.0 - 25.5
High Pressure Limit
58 psi
4.0 bar
0 - 369
0.0 - 25.5
Reference Flow
0.25 GPM (US)
0.81 l/min
0.18 GPM (UK)
0.00 - 26.42 (US)
0.00 - 999.99
0.00 - 22.00 (UK)
Reference Pressure
40 psi (US)
2.00 bar
29 psi (UK)
1 - 1450 (US)
0.10 - 99.99
1 - 1450 (UK)
User Setting
Nozzle Preset Setup
98-05204 R1 US
59
APPENDIX
OPERATION
SETUP
GETTING STARTED
OVERVIEW
User Setting
ISOBUS Job Computer : IC18 Sprayer
Calibrations
Implement Speed Sensor
Description
Factory Setting
Range/Options
Pulses per Distance
0
0 - 33445
Description
Factory Setting
Range/Options
CAN Speed Source Timeout
4 sec
0 - 999
Active Trip Count Imformtaion
Off
Off
On
Tank Content Minimum
0 GAL (US)
0 liters
0 GAL (UK)
0 - 2641 (US)
0 - 9999
0 - 2199 (UK)
Description
Factory Setting
Range/Options
Use Perferred VT
Off
Off
On
Pair with Switchbox
Auto
Auto
None
<<specific ID #>>
Pair with BoomPilot ECU
Auto
Auto
None
<<specific ID #>>
Show Number on Soft Key
No
No
Yes
Sprayer Number (FI)
1
1-9
User Setting
Alarm Configurations
User Setting
USER INTERFACE
OVERVIEW
GETTING STARTED
SETUP
OPERATION
APPENDIX
60
www.teejet.com
User Setting
ISOBUS Job Computer : IC18 Sprayer
APPENDIX B - UNIT SPECIFICATIONS
Dimensions
7.5 x 7.25 x 2.375 in
19.05 x 18.42 x 6.03 cm
Weight
1.42 lbs / 0.644kg
Connector
30 position Cinch pins. A1-K3
Input/Output
ISO 11783 (ISOBUS)
Power Requirement
<9 watts @12 VDC
GETTING STARTED
90% non-condensing
SETUP
-40 to +85°C
Humidity
OPERATION
Operating
98-05204 R1 US
61
APPENDIX
Environmental
OVERVIEW
30 position Cinch pins. L1-Y3
I C18 S P R AYE R
J O B CO M P U T E R
U S E R
Software Version 1.06
1801 Business Park Drive
Springfield, Illinois 62703 USA
Tel: (217) 747-0235 • Fax: (217) 753-8426
www.teejet.com
98-05204 R1 US
© TeeJet Technologies 2012
M A N U A L
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertisement