User`s Manual

Add to my manuals
22 Pages

advertisement

User`s Manual | Manualzz

LM-700

LM-700

17 inch TFT LCD Monitor

User’s

Manual

by Envision Peripherals, Inc.

www.aocmonitor.com

LM-700

Before operating your monitor, please read this manual thoroughly.

1

v3_123102

FCC Statement

This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy, and if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:

1. Reorient or relocate the receiving antenna.

2. Increase the separation between the equipment and receiver.

3. Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.

4. Consult the dealer or an experienced radio/TV technician for help.

For Your Safety

LM-700

Notice

1. The changes or modifications not expressly approved by the party responsible for compliance could void the user's authority to operate the equipment.

2. Shielded interface cables and AC power cord, if any, must be used in order to comply with the emission limits.

3. The manufacturer is not responsible for any radio or TV interference caused by unauthorized modification to this equipment. It is the responsibility of the user to correct such interference.

As an ENERGY STAR

®

Partner, Envision

Peripherals, Inc. has determined that this product meets the ENERGY STAR

®

guidelines for energy efficiency.

Warning

To prevent fire or shock hazard, do not expose the monitor to rain or moisture. Dangerously high voltage is present inside the monitor. Do not open the cabinet. Refer servicing to qualified personnel only.

LM-700

2

v3_123102

• Do not use the monitor near water, e.g. near a bathtub, washbowl, kitchen sink, laundry tub, swimming pool or in a wet basement.

• Do not place the monitor on an unstable cart, stand, or table. If the monitor falls, it can injure a person and cause serious damage to the appliance. Use only a cart or stand recommended by the manufacturer or sold with the monitor. If you mount the monitor on a wall or shelf, use a mounting kit approved by the manufacturer and follow the kit instructions.

• Slots and openings in the back and bottom of the cabinet are provided for ventilation. To ensure reliable operation of the monitor and to protect it from overheating, be sure these openings are not blocked or covered. Do not place the monitor on a bed, sofa, rug, or similar surface. Do not place the monitor near or over a radiator or heat register. Do not place the monitor in a bookcase or cabinet unless proper ventilation is provided.

• The monitor should be operated only with the type of power source indicated on the label. If you are not sure of the type of power supplied to your home, consult your dealer or local power company.

• Do not overload power strips and extension cords. Overloading can result in fire or electric shock.

• For use only with power adaptor manufactured by CHI SAM ELECTRONIC, model CH-1205.

Precautions

LM-700

• The monitor is equipped with a three-pronged grounded plug, a plug with a third (grounding) pin. As a safety feature, this plug will only fit into a grounded power outlet. If your outlet does not accommodate the three-wire plug, have an electrician install the correct outlet, or use an adapter to ground the appliance safely.

Do not defeat the safety purpose of the grounded plug.

• Unplug the unit during a lightning storm or when it will not be used for long periods of time.

This will protect the monitor from damage due to power surges.

• Never push any object into the slot on the monitor cabinet. It could short circuit parts causing a fire or electric shock. Never spill liquids on the monitor.

• Do not attempt to service the monitor yourself; opening or removing covers can expose you to dangerous voltage and other hazards. Please refer all servicing to qualified service personnel.

• To ensure satisfactory operation, use the monitor only with UL-listed computers which have appropriately configured receptacles marked between 100 - 240 V AC, Min. 5A.

• The wall socket should be installed near the equipment and should be easily accessible.

• Disconnect the power cord to stop the power supply to the monitor.

LM-700

3

v3_123102

Special Notes on LCD Monitors

The following symptoms are normal with an LCD monitor and do not indicate a problem:

• Due to the nature of the fluorescent light, the screen may flicker during initial use. Turn off the

Power Switch and then turn it on again to make sure the flicker disappears.

• You may find slightly uneven brightness on the screen depending on the desktop pattern you use.

• The LCD screen has effective pixels of 99.99% or more. It may include blemishes of 0.01% or less such as a missing pixel or a pixel lit all of the time.

• Due to the nature of the LCD screen, an afterimage of the previous screen may remain after switching from an image that has been displayed for hours. This after-image could require several hours to disappear.

• The life of the fluorescent light used in the LCD monitor is approximately 20,000 hours. Contact your dealer or EPI service center for replacement when the screen is dark, flickering or not lighting up. Never attempt to replace it by yourself.

For Your Safety

LM-700

General Notes

• Do not install the monitor near heat sources such as radiators or air ducts.

• Do not place monitor in direct sunlight or in areas with excessive dust, mechanical vibration or shock.

• Save the original shipping carton and packing materials in case you need to ship your monitor.

Be sure to repackage your monitor as it was originally packed at the factory.

• Periodically clean your monitor with a soft cloth.

Stubborn stains may be removed with a cloth lightly dampened with a mild detergent solution.

Never use strong solvents such as thinners, benzene, or abrasive cleaners, since these

will damage the cabinet. Always unplug the

monitor before cleaning it.

Using the Right Power Cord

The supplied power cord is a NEMA 5-15 style plug. It is UL-listed and CSA labeled for

125 volts AC.

If the monitor will be connected to your computer’s power outlet, use a minimum No. 18 AWG, type

SJT or SVT three conductors cord with one end terminating with a male grounded plug, rated 10A,

250V, CEE-22. The other end must terminate with a molded-on type connector body, rated 10A,

250V, having standard CEE-22 female configuration.

LM-700

4

v3_123102

Before You Operate the Monitor

Installing & Removing the Base

LM-700

General Features:

• 17" (43.2cm) TFT Color LCD Monitor

• Crisp, Clear Display for Windows

• Supports Resolutions up to 1280 X 1024 pixels

@75Hz

• EPA ENERGY STAR

®

• Ergonomic Design

• Space Saving, Compact Case Design

Package Contents

The box that your monitor was shipped in should have included the following items:

1. LM-700 LCD Monitor

2. Power Adaptor

3. Power Cord

4. Windows 95/98/2000/ME/XP INF Driver Disk

5. Quick Start Guide

6. Booklet (Containing Warranty & Safety

LM-700

5

v3_123102

Before You Operate the Monitor

Connecting the Wires Using the Power Cord Supplied

LM-700

1. Connect the built-in video cable into the 15-pin connector on the back of your computer and tighten the two screws.

2. Connect the power cord into the power adaptor.

3. Plug the other end of the power cord into a grounded AC outlet or UL-approved power strip.

4. Connect the power adaptor into the DC IN socket on the back of the monitor.

Caution: Make sure the power cord is the correct

type that is required in your area. This LCD monitor has a universal power supply that allows operation in either 100/120V AC or 220/240V AC voltage areas (no user adjustment is required).

If the AC outlet is not grounded (with three holes), install the proper grounding adapter (not supplied).

LM-700

6

v3_123102

Before You Operate the Monitor

LM-700

Connecting the Wires Using An Optional Power Cord (Not Supplied)

The power cord supplied with your monitor can only be connected to a grounded electrical wall socket or power strip.

If you wish to connect your monitor to a power supply using the power input socket on the back of your computer, you must purchase a power cord with CEE-22 terminated connectors (see illustration above).

Follow these steps:

1. Connect the built-in video cable into the 15-pin connector on the back of your computer and tighten the two screws.

2. Connect the power cord into the power adaptor.

3. Plug the other end of the power cord into the power output socket on your PC.

4. Connect the power adaptor into the DC IN socket on the back of the monitor.

LM-700

7

v3_123102

Before You Operate the Monitor

LM-700

Preparing to Install An Optional Wall Mounting Arm (Not supplied)

This monitor can be attached to a wall mounting arm you purchase separately. Disconnect power before this procedure. Follow these steps:

1. Pull the screw covers off the back of the monitor.

2. Support the base and remove the screws.

3. Unhook the cable into the monitor. Remove the base.

LM-700

8

4. Remove the back cover from the panel.

5. Follow the manufacturer’s instructions to assemble the wall mounting arm.

See next page for further installation instructions.

v3_123102

Before You Operate the Monitor

Install An Optional Wall Mounting Arm (Not supplied)

LM-700

Follow these steps to finish installing the wall mounting arm:

1. Place the wall mounting arm onto the back of the monitor. Line up the holes of the arm with the holes in the back of the monitor.

2. Insert the 4 screws into the holes and tighten.

3. Insert the power cable into the slot on the back of the monitor.

AOC's Model LM700 is compatible with the

Ergotron line of mounting and arm solutions.

Contact Ergotron at 800-888-8458 or visit their web site at www.ergotron.com for more information on the many ways on which you can mount your AOC LCD monitor.

LM-700

9

v3_123102

Before You Operate the Monitor

Adjusting the Viewing Angle

For optimal viewing, adjust the monitor's angle to your own preference.

• Hold the stand firmly when you change the monitor's angle.

• You can adjust the monitor's angle from

-5° to 30°.

• Do not touch the LCD screen when you change the angle. It may cause damage or breakage.

• Be careful to avoid pinching your hand in the swivel base.

LM-700

How to Install INF & ICM File

1. Insert the Windows 95/98/2000/ME/XP INF

Driver Disk into your floppy drive.

2. Follow the Add New Hardware Wizard instructions on the screen.

3. If the wizard asks for the location of the driver file, select drive A and press Next.

LM-700

10

v3_123102

Front Panel Buttons

Operating Instructions

LM-700

LM-700

Auto: Press this button to automatically set

the H-Position, V-Position, Clock and

Focus settings.

Brightness: Press this button to adjust the

picture’s brightness. If the OSD window is open, this button allows you to move within the window and select desired functions.

Contrast: Press this button to adjust the

picture’s contrast. If the OSD window is open, this button allows you to move within the window and select desired functions.

MENU: Press this button to open the OSD

window or exit from the OSD window.

11

Power Indicator: A green light indicates

that the monitor is on. An orange light indicates that the monitor is in Off mode.

Power: Press this button to turn the

monitor on or off. The power indicator will light up.

On-screen Display (OSD): Press the

MENU button to open the OSD window

and adjust settings on your monitor.

(See next page.) v3_123102

Operating Instructions

Adjusting the OSD Settings

LM-700

1. Press the MENU button to open the OSD window.

2. Press the < or > buttons until the desired function is highlighted.

3. Press MENU to open the function’s window.

4. Press the < or > buttons to change the settings of the function.

LM-700

12

5. To save and exit, highlight the EXIT icon and press MENU or leave the monitor alone for 10 seconds. If you want to adjust any other function, repeat steps 2-4.

Note: When the OSD window is open, the input

signal timing settings appear at the top.

H: stands for horizontal frequency and

V: stands for vertical frequency.

v3_123102

DOS-mode

This feature allows you to choose between resolutions of 720 x 400 or 640 x 400 while working in DOS-mode. Follow the instructions for selecting functions in the OSD window as listed on the previous page. Press your monitor’s Power button off and then on to activate your chosen

DOS-mode resolution. Note: the default DOSmode resolution is 720x400@70Hz.

How to Optimize the DOS-mode

1. Insert the Windows 95/98/2000/ME INF Driver

Disk into your floppy drive.

2. Open Windows Explorer to search on the floppy drive (Drive A:) to find the Dos1.exe file.

3. Double-click on the Dos1.exe file.

4. Expand the picture to full screen by pressing the icon on the top of window. If there is no icon, the picture is already at full screen.

If you don't have the driver disk:

1. Choose Start / Programs / MS-DOS mode.

2. Type C:\> EDIT and press Enter. You will be in the Dos-Editor screen.

3. Press the AUTO button on the front of your monitor for 2 seconds. The screen will be automatically adjusted.

If the screen is distorted (for example: the picture can't go to full screen, the background of white

Operating Instructions

LM-700

pattern has vertical stripe noise, or the characters are twisted):

1. Change the resolution to 640 x 400

2. Press the Power button off and then on.

3. Press the AUTO button for 2 seconds.

Note: the above procedure must process in full-screen pattern.

To exit, press the ESC key or press ALT-F, and then press the X key.

Plug & Play DDC1/2B Feature

This monitor is equipped with VESA DDC1/2B capabilities according to the VESA DDC

STANDARD. It allows the monitor to inform the host system of its identity and, depending on the level of DDC used, communicate additional information about its display capabilities. The communication channel is defined in two levels,

DDC1 and DDC2B.

The DDC1 is a unidirectional data channel from the display to the host that continuously transmits

EDID information. The DDC2B is a bidirectional data channel based on the I²C protocol. The host can request EDID information over the DDC2B.

LM-700

13

v3_123102

Technical Support (FAQ)

LM-700

Problem Possible Solution

Power LED is not ON • Make sure the power button is ON.

• Make sure the power adaptor is properly connected to a grounded power outlet and to the monitor.

No Plug & Play • Confirm that your computer is Plug & Play compatible.

• Confirm that your video card is Plug & Play compatible.

• Inspect the video cable and make sure that none of the pins are bent.

• Make sure the AOC monitor drivers are installed.

(AOC monitor drivers are available at: www.aocmonitor.com)

Picture is fuzzy

Picture bounces or a wave pattern is present in the picture

Power LED is ON

(green or orange light is ON) but there is no video or picture.

Missing one of the primary colors (RED,

GREEN, or BLUE)

• Adjust the Contrast and Brightness settings.

• Move electrical devices away from the monitor. They may be causing electrical interference.

• Press a key on the keyboard or wiggle the mouse to re-activate the monitor.

• Make sure the video cable is properly connected to the computer.

• Inspect the video cable and make sure none of the pins are bent.

• Make sure your computer is operating correctly by pressing the CAPS LOCK key and observing whether the CAPS LOCK light turns ON or OFF.

• Inspect the video cable and make sure that none of the pins are bent.

• Make sure the video cable is properly connected to the computer.

LM-700

14

v3_123102

Technical Support (FAQ)

LM-700

Problem

Screen image is not centered or sized properly

Picture has color defects (white does not look white)

Poor brightness or contrast

Possible Solution

• Adjust the CLOCK

1 and FOCUS

2

settings or press the AUTO button to automatically re-configure the monitor’s settings.

• Adjust the settings for Red, Green and/or Blue colors or select a different color temperature: 65 (6500 K) or 78 (7800 K).

Horizontal or vertical disturbances on the screen

• The life time of the back-light is limited. After 20,000 hours, the luminance of the light has been reduced to half of its original value.

Please send the monitor to an authorized service agent for service.

• Adjust the CLOCK and FOCUS settings or press the AUTO button to automatically re-configure the monitor’s settings.

• Use Win 95/98 shut-down mode.

1

CLOCK (pixel frequency) controls the number of pixels scanned by one horizontal sweep. If the frequency is not correct, the screen shows vertical stripes and the picture’s width is incorrect.

2

FOCUS adjusts the phase of the pixel clock signal. With a wrong phase adjustment the picture has horizontal disturbances with very light screen images.

Note: For FOCUS and CLOCK adjustment use “dot-pattern” or Win 95/98 shut-down mode pattern.

Error Message Possible Solution

Cable not connected • Make sure the video cable is properly connected to the computer.

If the connector is loose, tighten the connector's two screws.

• Inspect the video cable and make sure that none of the pins are bent.

LM-700

15

v3_123102

Technical Support (FAQ)

LM-700

Error Message

Input not supported

Unsupported mode try different video card setting

Resolution Chart

Resolution

(in pixels)

640 x 480

640 x 400

640 x 350

720 x 400

640 x 480

640 x 480

640 x 480

800 x 600

800 x 600

Possible Solution

• Your computer has been set to an incompatible display mode.

Right click on the desktop and choose Properties. Click the Settings tab then set your computer’s display mode to one of the settings listed in the resolution chart below.

• Your computer’s resolution is out of VESA specifications.

Right click on the desktop and choose Properties. Click the Settings tab then set your computer’s display mode to one of the settings listed in the resolution chart below.

Vertical

Frequency

60 Hz

70 Hz

70 Hz

70 Hz

72.8 Hz

75 Hz

66.67 Hz

56.3 Hz

60.3 Hz

Resolution

(in pixels)

800 x 600

800 x 600

832 x 624

1024 x 768

1024 x 768

1024 x 768

1024 x 768

1280 x 1024

1280 x 1024

Vertical

Frequency

72.2 Hz

75 Hz

74.5 Hz

60 Hz

70 Hz

75 Hz

74.92 Hz

60 Hz

75 Hz

LM-700

16

v3_123102

Appendix

Specifications

LCD

Panel

Driving system

TFT Color LCD

Input

Size

Pixel pitch

17.0" (43.2 cm)

Diagonal

0.264 mm (H) x

0.264 mm (V)

120° (H) 100° (V) Viewable angle

Response time

Video

50 milliseconds

Red, Green, Blue

Analog Interface

H/V TTL Separate

Sync.

H-Frequency 30 kHz - 80 kHz

V-Frequency 55-75 Hz

Display Colors

Dot Clock

Maximum Resolution

16.7 million colors

135 MHz

1280 x 1024 pixels

Plug & Play

Input Connector

Input Video Signal

Maximum Screen Size

Power Source

Environmental

Considerations

Weight

LM-700

VESA DDC1/

2BTM

D-Sub 15-pin

Analog: 0.7 Vpp

(standard),

75 OHM, Positive

Horizontal:

13.3" (337.92 mm)

Vertical:

10.6" (270.34 mm)

100~264 VAC,

47~63 Hz

Operating Temp:

32° to 104°F

(0° to 40°C)

Storage Temp:

14° to 122°F

(-10° to 50°C)

Operating

Humidity:

20% to 90%

12.1 lbs. (5.5 Kg)

LM-700

17

v3_123102

Appendix

Specifications (continued)

Front Panel Buttons Auto

Brightness

Contrast

Power Switch

MENU/ Exit

External

Controls:

Functions Contrast

Brightness

Focus

Clock

H-Position

V-Position

Auto-Center

Language

Dos-mode Resolution

Selected

6500° K

7800° K

RGB Color temp.

Recall

Exit

Yes EPA ENERGY

STAR®

Power Consumption

(Maximum)

45 Watts

Regulatory

Compliance

UL, CSA, FCC,

TCO99, TÜV/GS, CE

LM-700

Optimal Viewing Mode: 1280 x 1024 x 75 Hz

LM-700

18

v3_123102

Appendix

Factory Preset Timing Table

Standard

DOS-Mode

VGA

SVGA

XGA

SXGA

Resolution

(in pixels)

600 x 400

720 x 400

640 x 480

640 × 480

640 × 480

800 × 600

800 × 600

832 × 624

1024 × 768

1024 × 768

1024 × 768

1024 × 768

1280 x 1024

1280 x 1024

Horizontal

Frequency

31.47 kHz

31.47 kHz

31.47 kHz

35.00 kHz

37.50 kHz

37.879 kHz

46.875 kHz

49.725 kHz

48.363 kHz

56.476 kHz

60.02 kHz

60.241 kHz

64.00 kHz

80.00 kHz

LM-700

Vertical

Frequency

70 Hz

70 Hz

60 Hz

66.6 Hz

75 Hz

60 Hz

75 Hz

75 Hz

60 Hz

70 Hz

75 Hz

74.9 Hz

60 Hz

75 Hz

LM-700

19

v3_123102

Appendix

Connector Pin Assignment

7

8

5

6

3

4

1

2

Pin Number Description

Red

Green

Blue

Ground

Ground

R-Ground

G-Ground

B-Ground

13

14

15

9

10

11

12

Pin Number Description

+5V

Detect Cable

NC

DDC-Serial Data

H-Sync

V-Sync

DDC-Serial Clock

LM-700

LM-700

20

v3_123102

This is a warranty statement for Envision color monitors including those sold within North America as specified.

Envision Peripherals, Inc. (EPI) warrants this product to be free from defects in material and workmanship for a period of three (3) years after the original date of consumer purchase. During this period, EPI will, at its option, either repair the defective product with new or rebuilt parts, or replace it with a new or rebuilt product at no charge except as stated below*. The parts or product that are replaced become the property of

EPI.

* This limited warranty does not cover any losses or damages that occur as a result of:

• Shipping or improper installation or maintenance

• Misuse

• Neglect

• Any cause other than ordinary commercial or industrial application

• Adjustment by non-authorized source

• Repair, modification, or installation of options or parts by anyone other than an EPI Authorized

Service Center

• Improper environment

• Excessive or inadequate heating or air conditioning or electrical power failures, surges, or other irregularities. This three-year limited warranty does not cover any of the product's

Limited 3-Year Warranty

LM-700

firmware or hardware that you or any third party have modified or altered; you bear the sole responsibility and liability for any such modification or alteration.

All express and implied warranties for the product

(including the warranties of merchantability and fitness for a particular purpose) are limited in duration to a period of three (3) years for parts and labor from the original date of consumer purchase.

No warranties (either expressed or implied) apply after this period. In the United States, some states do not allow limitations on how long an implied warranty lasts. Therefore, the above limitations may not apply to you.

EPI’s obligations and your remedies hereunder are solely and exclusively as stated here. EPI’s liability, whether based on contract, tort, warranty, strict liability, or other theory, shall not exceed the price of the individual unit whose defect or damage is the basis of the claim. In no event shall EPI be liable for any loss of profits, loss of use or facilities or equipment or other indirect, incidental, or consequential damage. In the United States, some states do not allow the exclusion or limitation of incidental or consequential damages. Therefore, the above limitations may not apply to you.

LM-700

21

v3_123102

Warranty (continued)

LM-700

Although this limited warranty gives you specific legal rights, you may have other rights which may vary from state to state.

In the United States of America, this limited warranty is only valid for products purchased in the Continental United States, Alaska, and Hawaii.

Outside the United States, this limited warranty is only valid for products purchased in Canada.

In the United States, to obtain service under this limited warranty:

1. Call EPI’s Customer Service, RMA Department at the toll free number (888) 662-9888 for the nearest Authorized Service Center located in your area.

2. Ask for a Return Merchandise Authorization

(RMA) number.

3. Deliver the product freight pre-paid to the EPI

Authorized Service Center.

If you cannot deliver the product in person:

• Pack it in its original shipping container (or equivalent)

• Put the RMA number on the shipping carton

• Insure it (or assume the risk of loss / damage during shipment)

• Pay one-way shipping charge

EPI is not responsible for damage to inbound products that were not properly packaged.

EPI will pay the return shipment charges within one of the countries specified within this warranty statement. EPI is not responsible for any costs associated with the transportation of products across international borders. This includes the international borders of the countries within this warranty statements.

© 2002 Envision Peripherals, Inc.

LM-700

22

v3_123102

advertisement

Was this manual useful for you? Yes No
Thank you for your participation!

* Your assessment is very important for improving the workof artificial intelligence, which forms the content of this project

Related manuals

Download PDF

advertisement