AME International 14461 Low-Profile Bottle Jack Instruction manual
AME 14461 is a 20-ton low profile air hydraulic bottle jack designed for lifting heavy loads. It features a maximum height of 259 mm, a minimum height of 148 mm, and a gross weight of 11 kg. The jack requires an air pressure of 0.7-1.0 Mpa and comes with a package size of 355X165X165 mm. It is crucial to use the jack only on hard, level surfaces and to support the load by appropriate means after lifting. Additionally, never exceed the rated capacity and only use attachments or adapters supplied with or specifically sold for the jack.
Advertisement
Advertisement
INSTRUCTION MANUAL
& PARTS BREAKDOWN
# 14461
20 TON LOW PROFILE AIR
HYDRAULIC BOTTLE JACK
2347 Circuit Way, Brooksville, Florida, USA 34604
Phone: (+1) 352-799-1111 Toll Phone: (+1) 877-775-4AME (4263)
Fax: (+1) 352-799-1112 E-mail: [email protected] www.ameintl.net
Read this manual and follow all the safety rules and operating instructions before using this product.
INSTRUCTION MANUAL
WARNING!!
FAILURE TO READ THESE
WARNINGS MAY RESULT IN
PROPERTY DAMAGE AND
OR PERSONAL INJURY.
Use as lifting device only.
Use only on hard, level surface.
Support load by appropriate means after lifting.
Do not exceed rated capacity.
Do not modify jack.
Center load on the jack.
Only use attachments and/or adapters supplied with or sold specially for the jack.
Only lift areas of the vehicle designed by the vehicle manufacturer.
Failure to comply with all of these warnings may result in loss of load, damage to jack, and/or failure resulting in
personal injury or property damage.
Lifting Capacity
(Ton)
Max. Height
(mm)
Min. Height
(mm)
Gross Weight
(kg)
Net Weight
(kg)
Air Pressure
(Mpa)
20 259 148 11 10 0.7-1.0
Package Size
(mm)
355X165X165
Owner/Operator Responsibility
It is the owner/operator responsibility to properly use and maintain this equipment and the legibility of all warnings and instruction labels.
Carefully read and understand the instructions and warnings in this manual before operating this equipment. Keep this manual in a safe location for future reference.
Warranty of this unit will be void on any part if the unit subjected to misuse due to overloading, abuse, lack of maintenance and unauthorized modifications. No warranty – verbal, written or implied – other than the official, published AME new machinery and equipment warranty will be valid with this unit. In addition, it is your responsibility to be aware of existing Federal, State and Local codes and regulations governing the safe use and maintenance of this unit.
Inspection
Prior to each use, visually inspect for leaking hydraulic oil, damaged, loose or missing parts. If jack is worn or damaged, remove from service and contact your nearest service center for repair.
Maintenance
Check oil level. With the jack in an upright position and the ram completely retracted, open the release valve (turn counter-clockwise) and remove the filler plug. The oil level should be just up to the hole. Fill if necessary with clean hydraulic jack oil.
Lubricate internal components. With the release valve open, pump the jack for a while. Purge the hydraulic system of air. During transit the unit may become “air-bound”, causing a spongy ram action. To purge the system, close the release valve (turn clockwise). Pump the jack to full height. Open the release valve and push down on the ram. Repeat these steps if necessary to completely purge the system.
Keep the jack clean. Occasionally lubricate the handle socket pivot point, extension screw, release screw thread, and air valve to prevent corrosion.
2
INSTRUCTION MANUAL
1. Jack operation is controlled by external air pressure. Connect to an external air pressure source (clean connections prior to assembly).
2. To raise the jack, turn the release valve clockwise until tight and while connected to an air supply depress the air valve.
3. To lower the jack turn the release valve counter-clockwise slightly and very slowly. Be careful not to turn valve quickly or more than twice, otherwise, dangerous sudden lowering may occur.
USE JACK FOR LIFTING ONLY. LOAD MUST BE
SUPPORTED IMMEDIATELY BY OTHER APPROPRIATE MEANS.
3
INSTRUCTION MANUAL
4
5
INSTRUCTION MANUAL
Service: Contact your nearest authorized service center for repairs and/or replacement parts.
2347 Circuit Way, Brooksville, Florida, USA 34604
Phone: (+1) 352-799-1111 Toll Phone: (+1) 877-775-4AME (4263)
Fax: (+1) 352-799-1112 E-mail: [email protected] www.ameintl.net
6

Public link updated
The public link to your chat has been updated.
Advertisement