RGN CN565B Operating Manual

Operating Manual
--CN565B Construction Coil Nailer--
NOTE: Please read and fully understand the instructions in this
manual before operating the pneumatic power tool. Carefully read
through this OPERATOR'S MANUAL to ensure efficient, safe
operation. It is recommended that the Manual be kept readily available
as an important reference when using this tool.
1
IMPORTANT INFORMATION
WARNING: The warnings, cautions and instructions discussed in this instruction
manual cannot cover all possible conditions and situations that may occur. It
must be understood by the operator that common sense and caution are factors
which cannot be built into this product, but must be supplied by the operator.
When using the tool, basic safety precautions should always be followed to reduce the risk of
personal injury and damage to equipment.
Read and understand tool labels and operating instructions, safety precautions and warnings
in this manual before operating or maintaining this nailer.
Failure to follow warnings could result in DEATH or SERIOUS INJURY.
Most accidents that result from the operation and maintenance of nailers are caused by the
failure to observe basic safety rules or precautions. An accident can often be avoided by
recognizing a potentially hazardous situation before it occurs and by observing appropriate
safety procedures.
Basic safety precautions are outlined in the "SAFETY" section of this manual and in the
sections which contain the operation and maintenance instructions. Hazards that must be
avoided to prevent bodily injury or tool damage are identified as DANGERS or WARNINGS on
the nailer and in this manual.
Never allow the nailer to be operated by children or individuals who have not reviewed this
manual.
OPERATE THE NAILER ACCORDING TO THIS MANUAL.
WARNING!
Always follow the tool manufacturer's safety and
maintenance instructions.
Always wear safety glasses with side shields when
operating or servicing tools.
Always disconnect the air supply from the tool and empty
the magazine when servicing tools.
SAVE THIS MANUAL
FOR FUTURE REFERENCE!
2
WARNING:
The operating instructions shall draw attention to the following
a) Only those fasteners listed in the operating instructions may be used in the fastener driving
tools;
NOTE: The fastener driving tool and the fasteners listed in the operating instructions must be
seen as one unit system in terms of technical safety.
b) Only the main energy and the lubricants listed in the operating instructions may be used;
c) Fastener driving tools marked with an inverted equilateral triangle standing on one point
may only be used with an effective safety yoke;
d) Fastener driving tools equipped with contact actuation or continuous contact actuation,
marked with the symbol “Do not use on scaffoldings, ladders”, shall not be used for specific
application for example:
when changing one driving location to another involves the use of scaffoldings, stairs, ladders,
or ladder alike constructions, e.g. roof laths, closing boxes or crates, fitting transportation
safety systems e.g. on vehicles and wagons;
e) For the maintenance of fastener driving tools, only spare parts specified by the
manufacturer or his authorized representative shall be used;
f) Repairs shall be carried out only by agents authorized by the manufacturer or by other
specialists, having due regard to the information given in the operating instructions;
NOTE: Specialists are those who, as a result of professional training or experience, have
sufficient expertise in the field of fastener driving tools and sufficient familiarity with relevant
governmental industrial protection provisions, accident prevention regulations, directives and
generally recognized technical regulations (e.g. CEN- and CENELEC-standards), to be able to
assess the safe working condition of fastener driving tools.
g) Stands for mounting the fastener driving tools to a support for example a work table, shall
be designed and constructed by the stand manufacturer, in such a way that the fastener
driving tool can be safely fixed for the intended use, thus for example avoiding damage,
distortion or displacement.
Additional instructions for fastener driving tools operated by compressed air
a) Fastener driving tools operated by compressed air shall only be connected to compressed
air lines where the maximum allowable pressure cannot be exceeded by a factor of more than
10%, which can for example be achieved by a pressure reduction valve which includes a
downstream safety valve;
b) When using fastener driving tools operated by compressed air, particular attention must be
paid to avoid exceeding the maximum allowable pressure;
c) Fastener driving tools operated by compressed air should only be operated at the lowest
pressure required for the work process at hand, in order to prevent unnecessarily high noise
levels, increased wear and resulting failures;
d) Hazards caused by fire and explosion when using oxygen or combustible gases for
operating compressed air operated fastener driving tools.
3
SAFETY INFORMATION
WARNING:
BEFORE USING THE TOOL, READ CAREFULLY AND UNDERSTAND THE
FOLLOWING SAFETY INSTRUCTIONS.FAILURE TO FOLLOW WARNING
COULD RESULT IN DEATH OR SERIOUS INJURY.
1. WEAR SAFETY GLASSES OR GOGGLES.
Danger to the eyes always exists due to the possibility of dust being blown up by the
exhausted air or of a fastener flying up due to the improper handling of the tool. For
these reasons, safety glasses or goggles shall always be worn when operating the
tool. The employer and/or user must ensure that proper eye protection is worn. The employer
is responsible to enforce the use of eye protection equipment by the tool operator and all other
personnel in the work area. NOTE: Non-side shielded spectacles and face shields alone do not
provide adequate protection.
2. EAR PROTECTION MAY BE REQUIRED IN SOME ENVIRONMENTS.
As the working condition may include exposure to high noise levels which can lead
to hearing damage, the employer and user should ensure that any necessary
hearing protection is provided and used by the operator and others in the work area.
3. DO NOT USE ANY POWER SOURCE EXCEPT AN AIR COMPRESSOR.
The tool is designed to operate on compressed air. Do not operate the tool on any
other high pressure gas, combustible gases (e.g. Oxygen, acetylene, etc.) since
there is the danger of an explosion. For this reason, absolutely so not use anything
other than an air compressor to operate the tool.
4. OPERATE WITHIN THE PROPER AIR PRESSURE RANGE.
The tool is designed to operate within an air pressure range of 70 psi
to100 psi (5 to 7 bar). The pressure should be adjusted to the type of the
work being fastened. The tool shall never be operated when the operating
pressure exceeds 120 psi. (8.3 bar).
5. DO NOT OPERATE THE TOOL NEAR A FLAMMABLE SUBSTANCE.
Never operate the tool near a flammable substance (e.g., thinner, gasoline, etc.).
Volatile fumes from these substances could be drawn into the compressor and
compressed together with the air and this could result in an explosion.
4
6. DO NOT USE A WRONG FITTING.
The connector on the tool must not hold pressure when air supply is disconnected. If a wrong
fitting is used, the tool can remain charged with air after disconnecting and thus will be able to
drive a fastener even after the line of air is disconnected, possibly causing injury.
7. DISCONNECT THE AIR SUPPLY AND EMPTY THE MAGAZINE WHEN THE TOOL IS
NOT IN USE.
Always disconnect the air supply from the tool and empty the magazine when operation has
been completed or suspended, when unattended, moving to a different work area, adjusting,
disassembling, or repairing the tool, and when clearing a jammed fastener.
8. INSPECT SCREW TIGHTNESS.
Loose or improperly installed screws or bolts cause accidents and tool damage when the tool
is put into operation. Inspect to confirm that all screws and bolts are tight and properly installed
prior to operating the tool.
9. DO NOT TOUCH THE TRIGGER UNLESS YOUR INTEND TO DRIVER A FASTENER.
Whenever the air supply is connected to the tool, never touch the trigger unless you intend to
drive a fastener into the work. It is dangerous to walk around carrying the tool with the trigger
pulled, and this and similar actions should be avoided.
10. NEVER POINT THE DISCHARGE OUTLET TOWARD YOURSELF AND PERSONNEL.
If the discharge outlet is pointed toward people, serious accidents may be caused when
misfiring. Be sure the discharge outlet is not pointed toward people when connecting and
disconnecting the hose. Loading and not loading the fasteners or similar operations.
11. USE SPECIFIED FASTENERS.
The use of fasteners other than specified fasteners will cause the tool malfunction. Be sure to
use only specified fasteners when operating the tool.
12. PLACE THE DISCHARGE OUTLET TO THE WORK PROPERLY.
Failure to place the discharge outlet of the nose in a proper manner can result in a fastener
flying up and is extremely dangerous.
13. KEEP HANDS AND BODY AWAY FROM THE DISCHARGE OUTLET
When loading and using the tool, never place a hand or any part of body in fastener discharge
area of the tool. It is very dangerous to hit the hands or body by mistake.
5
14. DO NOT DRIVE FASTENERS CLOSE TO THE EDGE AND CORNER OF THE WORK
AND THIN MATERIAL
The work piece is likely to split and the fastener could fly and hit someone.
15. DO NOT DRIVE FASTENERS ON THE TOP OF OTHER FASTENERS.
Driving fasteners of the top of other fasteners may cause deflection fasteners which could
cause injury.
16. REMOVING THE FASTENERS AFTER COMPLETING OPERATION
If fasteners are left in the magazine after the completion of operation, there is the danger of a
serious accident occurring prior to the resumption of operation, should the tool be handled
carelessly, or when connecting the air removes all fitting. For this reason, always move the
fasteners away which remaining in the magazine after completion of the operation.
17. CHECK OPERATION OF THE CONTACT TRIP MECHANISM FREQUENTLY IN CASE
OF USING A CONTACT TRIP TYPE TOOL
Do not use the tool if the trip is not working correctly as accidental driving of a fastener may
result. Do not interfere with the proper operation of the contact trip mechanism.
18. WHEN USING THE TOOL OUTSIDE OR ELEVATED PLACE.
When fastening roofs or similar slanted surface, start fastening at the lower part and gradually
work your way up. Fastening backward is dangerous as you may lose your foot place. Secure
the hose at a point close to the area you are going to driver fasteners. Accidents may be
caused due to the hose being pulled inadvertently or getting caught.
19. NEVER USE THE TOOL IF ANY PORTION OF THE TOOL CONTROLS (e.g., TRIGGER,
CONTACT ARM) IS INOPERABLE DISCONNECTED, ALTERED OR NOT WORKING
PROPERLY.
20. NEVER ACTUATE THE TOOL INTO FREE SPACE.
This will avoid any hazard caused by free flying fasteners and excessive strain of the tool.
21. ALWAYS ASSUME THAT THE TOOL CONTAINS FASTENERS.
22. DO NOT USE ON SCAFFOLDINGS LADDERS.
The tool shall not be used for specific application for example:
 When changing one driving location to another involves the use of
scaffoldings, stairs, ladders, or
 Ladder alike constructions, e.g. roof laths,
 Closing boxes or crates,
 Fitting transportation safety systems e.g. on vehicles and wagons.
6
TECHNICAL DATA
Type of tool
CN565B Construction Coil Nailer
Dimensions
320mmX130mmX273mm
Weight (without fasteners)
2.50kgs
Actuation mode
Contact/Single-sequential actuation
Magazine capacity
250-400 nails (wire welded nails)
200 nails (plastic sheet collated nails)
Maximum allowable pressure
8.3 bar (120psi)
Recommended pressure range
5 bar to 7 bar (70psi to 100psi)
Fasteners
Only the nail sizes shown in the table below can be driven with this nailer.
15°Conical wire welded coil nails & flat plastic sheet collated nails
Applications
 Siding (hardboard and cement);
 Sheathing, fencing and sub-flooring;
 Roof decking;
 Exterior deck and trim;
 Furring and strapping.
7
NAILER CONNECTION AND OPERATION
NOTE: The information contained in this manual is designed to assist you in the safe operation
of the nailer. Some illustrations in this Manual may show details or attachments that are
different from those on your nailer.
Air Supply, Connections and Operating Pressure
Read section titled SAFETY. Make sure of the following before operation: Air Supply
Power Source (Compressor)
 Use only clean, dry, regulated compressed air as a power source for this nailer.
 NEVER use oxygen or other bottled gases, as an explosion may occur.
 Use suitable air compressors used to supply compressed air to this nailer
 Moisture or oil in the air compressor may accelerate wear and corrosion in the
nailer.
 Drain daily.
Connections
1. Fittings
Install a female coupler to the hose. The female coupler will connect to the quick release that
fits the tool.
2. Filter-Regulator-Lubricator
 NEVER connect nailer to pressure which potentially exceeds 120psi.
 Filter-regulator-lubricator units supply an optimum condition for the nailer and extend
the nailer life. These units should always be used.
Filter
 The filter removes moisture and dirt mixed in compressed air.
 Keep the filter clean by maintaining tool regularly.
 Darin daily.
Regulator
 The regulator controls the operating pressure for safe operation of the nailer.
 Inspect the regulator before operation to be sure it operates properly.
8
Nailer Connection and Operation
Lubricator
 The lubricator supplies and oil mist to the nailer.
 Inspect the lubricator before operation to be sure the supply of lubricant is adequate.
 If an inline lubricator is not used, a few drops of oil will need to be added to the nailer
inlet before each use.
3. Air Hose
Air hose must have a minimum working pressure rating of 180 psi.
Hose has a min. ID of 1/4"(ISO 7-1) and max. length of no more than 17'(5 meter).
The supply hose should contain a fitting that will provide "quick disconnecting" from the
male plug on the tool.
Operating Pressure
 Recommended operating pressure range is 70 to 100 psi.
 Maximum permissible operating pressure is 120 psi.
 Select the operating pressure within this range for the best fastener performance. The
nail length and thickness and the hardness of the wood are factors in determining what
the pressure should be set at.
 Do not exceed this recommended operating pressure.
NOTE: Dirt and water in the air supply are major causes of wear in the tool.
An air filter will help to get the best performance and minimum wear from the tool. Frequent,
but not excessive, lubrication is required for the best performance. Oil added through the air
line connection will lubricate the internal parts.
WARNING
NEVER connect nailer to pressure which potentially exceed
120psi.
DO NOT USE THE WRONG FITTING ON NAILER.
The nailer and air hose must have a hose coupler so that all
pressure is removed from the nailer when the coupler is
disconnected. The connector on the tool must not hold pressure
when the air supply is disconnected. If the wrong fitting is used,
the tool can remain charged with air after disconnecting and thus
will be able to drive a nail even after the air line is disconnected,
possibly causing injury.
DANGER
NEVER use oxygen or other bottled gases, as an
explosion may occur.
9
INSTRUCTION FOR OPERATION
1. Before operation
(1) Wear safety glasses or goggles
(2) Do not connect the air supply
(3) Inspect screw tightness
(4) Check operation of the contact arm & trigger if moving smoothly
(5) Connect the air supply
(6) Check the air-leakage.(the tool must not have the air-leakage.)
(7) Hold the tool with finger-off the trigger, then push the contact arm against the workpieces.(the tool must not operate.)
(8) Hold the tool with contact arm free from work-piece and pull the trigger.(the tool must not
operate.)
2. Operation
Keep hands and body away from the discharge outlet when driving the fasteners because of
dangerous of hitting the hands or body by mistake.
Nail loading
(1) Disconnect the air hose.
(2) Press LATCH (210270) to open DOOR (210250), then open MAGAZINE COVER (420530).
(3) Adjust the height of NAIL SUPPORT (420210) according to nails length.
(4) Fix the first nail in the groove on FEED PAWL (210210).
(5) Close MAGAZINE COVER (420530), close DOOR (210250).
(6) Connect the air hose.
Test operation
(1) Adjust the air pressure at 70psi. (5 bar) and connect the air supply.
(2) Without touching the trigger, depress the contact arm against the work-piece. Pull the
trigger.(the tool must fire the fastener.)
(3) With the tool off the work-piece, pull the trigger. Then depress the contact arm against the
work-piece.(the tool must fire the fastener.)
(4) Adjust the air pressure as much as the lowest possible according to the diameters and
length of fastener and the hardness of work-piece.
10
MAINTENANCE AND INSPECTION
Read the section title SAFETY.
SERVICE AND REPAIRES
All quality tools will eventually require servicing or replacement of parts due to wear from
normal use. It is recommended that these operations should be performed by a professional
technician.
NOTE: The information contained in this Manual is designed to assist you in the safe
maintenance of the nailer. Some illustrations in this Manual may show details or attachments
that are different from those on your nailer.
WARNING: Disconnect air hose and remove nails from nailer when:
 Doing maintenance and inspection
 Cleaning a jam
Inspecting the magazine
1. DISCONNECT AIR HOSE.
2. Clean the magazine. Remove dust which may have accumulated in the magazine.
3. Lubricate the nailer rail with nailer lubricant.
Clearing a jam
Remove a jammed nail in the following order:
1. DISCONNECT AIR HOSE.
2. Remove all nails.
3. Remove the jammed nail with a slotted head screwdriver.
4. In case of frequent jams, contact an authorized service center.
A qualified person should perform repair and maintenance
Periodic maintenance to be performed:
 Check that the piston bumper is operating normally. A damaged piston bumper may
cause damages to other component parts.
 Check o-rings for wear or damage. Damaged o-rings may affect overall performance.
 Make sure all screws are secure. Loose screws may affect overall performance.
 When repairing a tool, make sure the internal parts are clean and lubricated.
Storing
 When not in use of an extended period, apply a thin coat of the lubricant to the steel
parts to avoid rust.
 The nailer should be stored in a warm and dry place when not in use. Do not store the
nailer in a cold weather environment.
11
`PARTS LIST-CN565B
NO.
CODE
Description
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30
31
32
33
34
35
36
37
38
39
40
41
42
43
44
45
46
47
48
49
50
51
52
53
54
55
56
610550
320940
410280
320930
320920
110210
610230
320910
320900
410270
320890
620380
420610
510710
510560
410260
410250
520130
511010
510680
310180
420600
110200
640180
410460
323220
620370
110190
320880
420590
420580
321810
420950
510220
321740
620670
420560
640020
421080
420650
323120
320980
310190
510510
620910
510140
320970
640250
510410
420090
510380
420080
320110
510030
620050
510240
BOLT M6X20
BUSHING
EXHAUST COVER
EXHAUST FILTER (A)
EXHAUST FILTER (B)
CYLINDER CAP
BOLT M6X30
SIDE PROTECTOR
PISTON STOP SEAT
PISTON STOP
WASHER
COMPRESSION SPRING
HEAD VALVE PISTON
O-RING 54X3.1
O-RING 41.2X2.65
HEAD VALVE SLEEVE
BUMPER
CYLINDER SEAL
O-RING 63.8X3.1
O-RING 50X2.65
CYLINDER
CYLINDER RING
BODY
ROLL PIN 3X30
HANDLE GRIP
DOWEL PIN
SPRING
ADJUST BUTTON
CONTACT PLATE
TRIGGER BRACKET
TRIGGER
STEP PIN
PIN CAP
O-RING 6.7X1.8
SAFETY UPPER
SPRING
SAFETY UPPER GUIDE
ROLL PIN 2.5X10
ADJUST DIAL
SAFETY GUIDE
SAFETY
DRIVE BLADE (Loctite)
PISTON
O-RING 37.5X3.55
SNAP RING 4
O-RING 5.15X1.8
ADJUSTER
STRAIGHT PIN B3X15
O-RING 18.3X2.65
TRIGGER VALVE CAGE
O-RING 16X1.8
TIGGER VALVE CAP
TIGGER STEM
O-RING 2.5X1.4
SPRING
O-RING 8.6X1.9
NO.
CODE
57
58
59
60
61
62
63
64
65
66
67
68
69
70
71
72
73
74
75
76
77
78
79
80
81
82
83
84
85
86
87
88
89
90
91
92
93
94
95
96
97
98
99
100
101
102
103
104
105
106
107
108
109
110
P1
P2
510210
330010
510180
420640
320800
620390
320960
420170
210210
320780
110220
320850
420630
420620
210250
420160
210230
620300
620070
210240
320950
610110
210270
620430
320990
610320
510640
610220
510260
620340
320770
510390
620420
620410
410240
320760
630080
410290
110310
420540
630110
420240
421570
610130
630340
320260
620650
420210
420520
420530
620740
520160
323130
410880
D320981
T420091
Description
O-RING 6.3X1.8
TRIGGER VALVE BUSHING
O-RING 5.8X1.9
PIN CAP ©
STEP PIN
FEED SPRING
CHECK TOE
PIN CAP (A)
FEED PAWL
FEED PAWL PIN
NOSE
DOOR PIN
DUST COVER
GUARD COVER
DOOR
PIN CAP (B)
CHECK PAWL (A)
CHECK SPRING (A)
CHECK SPRING (B)
CHECK PAWL (B)
CHECK PAWL PIN
BOLT M5X22
LATCH
LATCH SPRING
STEP PIN
NUT M5(Nylock)
O-RING 47.5X1.8
BOLT M6X25(Loctite)
O-RING 9X1.8
SPRING
FEED PISTON
O-RING 17X2.65
FEED PISTON SPRING (A)
FEED PISTON SPRING (B)
FEED PISTON BUMPER
FEED PISTON CAP
SNAP RING 24
NOSE CAP
END CAP
FILTER
SNAP RING 32
SPRING HOLDER (B)
MAGAZINE
BOLT M5X30
WASHER
MAGAZINE PIN
MAGAZINE SPRING
NAIL SUPPORT PLATE
SPRING HOLDER (A)
MAGAZINE COVER
SPRING
GASKET
STRAIGHT PIN
STRAIGHT PIN CAP
DRIVER UNIT
TRIGGER VALVE
12
TOOL SCHEMATIC-CN565B
13
IMPORTER:
NOBE ApS
Bjødstrupvej 10
DK – 8410 Rønde
Denmark
Tel: + 45 8615 1913
E-Mail: [email protected]
www.nobe.dk / www.rgneurope.com
--Construction Coil Nailer CN565B-2016
14
">