CASKA car multimedia & navigation system is a device that allows you to enjoy music, videos and other media in your car. You can also use the system to navigate to your destination. The system is compatible with a variety of media formats, including DVD, VCD, CD, MP3, JPEG, MPEG4, CD-R, and more. It also includes features such as Bluetooth hands-free calling, a rear zone function, and a tyre pressure detection module.
Advertisement
Advertisement
Contents
1.Basic Operation----------------------------------------------------------------01
2.Function Operation-------------------------------------------------------------03
2.1 RADIO Function Operation-------------------------------------------------03
2.2 DVD Function Operation---------------------------------------------------
05
2.3 Bluetooth Handfree -------------------------------------------------------
22
2.4 CDC
Function Operation
---------------------------------------------------
28
2.5 TV Function Operation
----------------------------------------------------30
2.6 iPod
Function Operation
---------------------------------------------------
31
2.7 AV Function Operation
----------------------------------------------------
36
2.8 OBD Function Operation---------------------------------------------------37
2.9 NAV Function Operation---------------------------------------------------
38
2.10
Rear Zone Function Operation
-
40
2.11
TPMS
-
41
2
.
12
-
44
2.13
Button Background Adjustment-
----------------------------------------------
45
-
46
3.System Setup------------------------------------------------------------------48
4.Accessories(optional)-----------------------------------------------------------58
4.1 Car Backing Sensor Installation---------------------------------------------
58
4.2 Car Backing Camera Installation --------------------------------------------
63
4.3 Description of the Buttons on Remote Control---------------------------------
64
4.4 RDS Function Operation
(optional)-------------------------------------------
66
5.Precautions-------------------------------------------------------------------68
6.Trouble Shooting--------------------------------------------------------------70
Note
For use the product safely and correctly, please read this manual carefully.
Because of technology improvement, the specifications is subject to change without further notice!
Basic Operation
Turn on
If you pull out the car key to turn off the host unit last time, insert the key again, and the host unit will be turn on automatically.
If you press the power button on the panel to turn off the host unit last time, press the power button slightly again to turn on the host unit .
Turn off
Pull out the car key, and the system will recognize the information to turn off the host unit.
Press and hold the power button for more than 2s, and the system will turn off automatically
(
Subject to the actual model
).
During start-up state, touch the screen slightly, and “Home page” icon will be displayed on the upper left corner of the screen. Press the “Home page” icon slightly again to enter the main page menu.
.
Touch the icon of each function to enter the corresponding function operation.
Note
If touch the above-mentioned icon slight, and “Device not connected” will be indicated, which represents no connection between the device and the host unit at present.
1
Basic Operation
While the spectrum display is enabled, screen will automatically switch to spectrum mode if there is no operation within 10 seconds when playing in radio, DVD or disc changer status, or disc without video.
At video playing status, open the home page, the screen will switch to spectrum mode after 10s.
Touch “Spectrum mode” slightly to switch among different spectrum display modes
(as figure shows).
Panel Board Spectrum
Rectangle Spectrum
Switch spectrum mode
DVD T-1 00:12
Play Information
Switch Sound Field Mode
62Hz 62Hz
During spectrum mode interface, touch to switch among different sound field modes.
CUSTOM
ROCK
JAZZ
POP
CLASSIC
FLAT
Press the volume adjustment key on the panel to adjust the volume.
Press the Mute key on the panel to execute mute function, and “ ” icon will indicate the mute state.
2
Function Operation
Touch the screen slightly to open the touch menu.
Touch the “ Home page ” icon slightly to enter home page interface, and touch slightly to enter radio interface.
On radio interface, the small spectra shown in the right-side of screen, click the icon “EXIT” to return to Main menu. If no operation within 10 seconds, the unit enters the spectra mode
Click the icon "the spectra mode" to adjust the spectra value, click the screen again to return to the radio interface
Click the icon "Main menu" to enter Main menu, click these icons to enter the corresponding interface
搜索
Touch “SEEK” icon to enter automatic
search status, and save the station automatically during automatic search.
Touch the “SEEK” icon again to stop automatic search.
FM: 87.50MHz~108.00MHz
AM: 522KHz~1620KHz
18 radio stations can be stored for
FM (6 stations for each of FM1,
FM2 and FM3), 6 stations can be stored for AM.
3
Function Operation
Touch / icon to enter semi-automatic tuning state of LF/HF channel.
Click “Start tuning” once to start search, and click it again to stop search.
When a radio station is received，search will be stopped. Press and hold one radio station number for more than 2s,and the received radio station will be stored to the station number.
Touch “Band” icon slightly to switch among FM1, FM2, FM3 and AM.
Select the band first, and then touch the screen preset station No.
M1-M6 to play the preset station corresponding to the number
(station selected will turn green);
For example: The figure on the right represents FM1,and frequency of 102.50MHz.
4
Function Operation
This unit plays discs in formats like DVD/VCD/CD/MP3/JPEG/MPEG4/ CD-R, etc.
(Limited to diameter 12cm standard disc).
Touch the screen slightly to open the touch menu.
Touch the MAIN icon slightly to enter home page interface, and touch slightly to enter
DVD interface.
Touch “Home page” icon slightly to enter home page, and then touch other function to exit from DVD function.
If a portable hard disc is connected, touch the “DVD” icon slightly again to enter USB playing status.
On radio/AV/TV/iPod interface, insert the disc, the unit enters to DVD interface.
On Navigation state, insert the disc, the unit can play the DVD, no video but sound; on GPS mode, insert the disc, the unit do not enter DVD interface.
In the DVD status, when “Open the compartment” is displayed on the screen, with the printed face upward, insert the disc into the compartment. When the system detects the disc, the disc will be automatically in-taken, read and played.
If there is a disc in the DVD ROM, press “ ” button on the panel to exject the disc.
If the disc isn't removed within 12s, the system will take in the disc again and play.
5
Function Operation
Touch the icon slightly(as the
Figure on the right shows )
When the number pad pops out, click the number key on the number pad to select a song directly, and then press to confirm the play, or wait for some seconds until the song is played automatically. Click to hide the number pad.
主页
Note: While DVD/VCD/CD playback, if you want to select the track more than 10 to play, first, click the button “10+”, second, click the designed button (Button 1-----9).
For example, to select the track 58, first, clicks the button “10+” 5 times, second, click the button 8, it is OK.
While MP3/MP4 playback, if you want to select the track more than 10 to play, first, directly click the digital button of soft keyboard on the screen, second, click the button
“OK” to begin playback. For example, to select the track 12, first, clicks the button “1”, second, click the button 2, finally, click the button“OK” to play.
×
FR
Next track
×
FF
Play/pause
Previous track
6
Function Operation
Stop/Back to title menu/PBC switch (disc support is required)
Switch DVD language (disc support is required); switch VCD sound.
Switch DVD caption (disc support is required)
Image can be captured when playing JPEG disc
Menu column of the next page
Menu column of the previous page
Enlarge/diminish image
Repeat
Turn on/off DVD setting menu
On fast-forward playback, click the button fast-reverse to enter the normal playback.
On fast-reverse playback, click the button fast- forward to enter the normal playback.
Touch the screen blank to show/hide the menu
Touch icon slight to exit from touch menu.
Touch icon slight to enter home page menu.
7
Function Operation
If a DVD inside the host unit, and the disc doesn't have a play menu, the system will automatically read the disc and play directly; if the disc has a play menu
，
Click the icon to play
Normal
Select song
Click the icon” ### ” to return DVD mode (DVD disc required)
During playing a disc, click the upper right part of the screen to display the play information.(as right picture show)
DVD T-01 02:16 play
My HEART WILL GO ON
Near, far, wherever you are, I believe that the heart does go on.
Current track number
Play time Play status
Note
During playing, operate the touch menu to perform various play controls. For function definitions of touch menu, please refer to the 4th item of DVD function operation “ Functions of Touch Menu
”.
8
Function Operation
Put a VCD into the DVD player,and the disc will be read and automatically played in normal order.
BIG BIG WORLD
I’m a big big girl, I’m a big big world.
It’s not a big big thing if you leave me.
During play a disc, click to return to disk PBC menu contents.
(Disc support be required)
If the disc supports function which you can select digit directly to play selected song, open the digit keyboard to select song to play directly.
Select songs 01/15
My HEART WILL GO ON
Near, far, wherever you are, I believe that the heart does go on.
Select
songs 01/15
/ of sub menu
Note
During playing, operate the touch menu to perform various play controls. For function definitions of touch menu, please refer to the 4th item of DVD function operation “ Functions of Touch Menu
”.
9
Function Operation
Put a CD into the DVD player,and the disc will be read and automatically played in normal order.
Songs
03/17 00:34
Songs
03 / 17 00:34
/ of sub menu
Play time
While the disc playing, click the icon “ ” to pause, click the icon “ ” again to continue playing.
During playing a disk, the system will automatically switch to spectrum state if there is no operation within 10s.
If the disc has the title, the track can be chosen directly by the soft key board
Note
During playing, operate the touch menu to perform various play controls. For function definitions of touch menu, please refer to the 4th item of DVD function operation “ Functions of Touch Menu
”.
10
Function Operation
Put MP3 disc into the DVD player, and the disc will read, and the system will play the first file automatically.
00:15 03:42
001/018
\001\
MP3
MP3
MP3
MP3
MP3
..
001
002
003
004
005
Disc play information state name
Current
The current track time
00:15 03:42
001/018
The current track
Track amount
of sub menu
During playing mode , click at the first time ,it can back to file menu.
or click directly
..
can back to file menu too.
00:15 03:42
001/018
\001\
001
002
003
004
005
006
128kbps
Play status
Touch / cursor to select track. and then click
The scroll bar to view the file list, click file name to play.
During playing a disc, the system will automatically switch to spectrum status if there is no operation within 10s.
Note
During playing, operate the touch menu to perform various play controls. For function definitions of touch menu, please refer to the 4th item of DVD function operation “ Functions of Touch Menu
”.
11
MPEG4 D
MPEG is the abbreviation of "Moving Pictures Experts Group", the Chinese denomination for "Dynamic image specialist group", and the MPEG4 is the fourth generation encoder standard for video audio as released by the specialist's group.
The play operation of MPEG4 disc is basically same as the DVD disc, no longer rewording here.
The MPEG4 disc available on the market adopts different kinds of engraving format, such as: XVID, the AVI DIVX, RM, etc. And it is a normal phenomena if part of discs not available to be played at the player because of the format reason.
MPEG files are displayed on the player in the form of folder/file. Move the cursor to the small icon at the front through the direction button and press the play button for play. The detailed operation refer to the “MP3 disc playing”.
Contents interface:
00:15 03:42
001/018
\001\
MP3
MP3
MP3
MP3
MP3
..
001
002
003
004
005
The other play interface is the same as the one of DVD play.
Function Operation
12
Function Operation
Put JPGE disc into the DVD player, and the disc will be read, and the system will play the first file automatically.
Play Status
During playing, click once to return to image browse interface.
Browse interface
Previous Next
Random
Click directly the picture to begin playing to page up/down to browse images.
Click the icon” random” to play the picture in the current folder at random.
Click one more time , it can return to the catalogue menu Contents menu interface
interface.
00:15 03:42
001/018
..
A02
A03
A04
A05
A06 Image preview window
Resolution 1150X866 DISC
Current image resolution
13
Function Operation
Click to page up/down to browse images.
Click the scroll bar to view the file list, click file name to play.
On the directory menu, to return the folder directory menu, click the icon
again or Click the icon
.
On the subdirectory menu, click the subdirectory to play the picture.
While in browse interface, click to obtain current image and use it as the start-up image for DVD state custom mode.
Note
Only by setting “Startup Picture” on the “Universal Setup Page” as the
“Customer image” in the DVD setting menu can the snatched picture be used as the startup picture display.
When you capture an image again, the previously captured image will be replaced automatically.
14
Function Operation
If the player is equipped with a multi-media SD card port, this operation is available.
Open the monitor and insert the SD card, with media information into the SD card slot directly until the card is locked.
For taking out the SD card, exit from SD card playing status first, and then press the
SD card slightly to cancel the locking status of the SD card and exject the card automatically.
While in DVD function status, touch the “Home page” icon to enter home page menu, and then touch to enter SD card playing mode.
00:15 03:42
001/018
\001\
MP3
MP3
MP3
MP3
MP3
..
001
002
003
004
005
SD
/
MMC
After the SD card is read, the operation is the same as the one for playing MP3 disc. For detailed information, please refer to “play Mp3 disc ”.
15
Function Operation
If the player is equipped with a USB port, this operation is available.
If the player is equipped with a USB port, portable hard disc can be connected through USB wire or directly inserting into the USB port.
For taking out portable hard disc, please exit from portable hard disc play image first and then taking out the disc.
While in DVD function status touch the “Home page” icon to enter home page menu, and then touch to enter portable
hard disc playing mode.
00:15 03:42
001/018
\001\
MP3
MP3
MP3
MP3
MP3
..
001
002
003
004
005
USB
After the portable hard disc is read, the operation is the same as the one for playing MP3 disc.
For detailed information, please refer to “MP3 disc play”.
As standards of manufacturers which produce portable hard disc with MP3 player are different, it may cause that some portable hard disccan not be played.
The USB connecting wire is better to be the shortest when used to connect, or else it ay cause abnormal operation of the portable hard disc.
Note
If the main machine is connected to both multi-media SD card and USB flash disk simultaneously while in DVD function state, touch “DVD” once to access SD card play, touch it twice to access USB flash disk play, and touch it three times to access disk play.
16
Function Operation
Enter to DVD state, open the touch menu.
Gently touch “DVD to set” .
- -
General Setup Page
-
-
Tv Display
Angle Mark
Osd Lang
Captions
Last memory
Loge Type
Ps
On
Eng
On
On
DEF
General Setup Page
Audio Setup Page
Preference Setup
Page
Exit from the
Setup Menu
To Audio setup page
Password Setup Page
Click again to exit from the setting menu.
(General setup page interface)
On the DVD mode, click the icon to enter the corresponding function interface.
Touch directly the icon of each setup menu on the screen to select the item to confirm the current setup. Click icon to exit.
17
Function Operation
General Setup Page
TV Display
Normal/Ps
Images will be scanned and output in the format of “Panorama”
Wide
Images will be output in the format of “Wide screen (16:9)”
Normal/LB Images will be output in the format of “Message box”
Angle Mark
On/Off It display the angle mark
SPDIF Setup Page
SPDIF Setup
Output/Off
Meaning that the output signal is an analog signal
SPIDF/RAW
Meaning that the ture form source code flow of the DVD disc is delivered directly through digital port
SPIDF/PCM
Meaning that the code flow of the disc had been decoded before it was encoded into the PCM digital signal output. That entry is selected when the DVD audio output analog signal is connected with 2-channel digital stereo amplifier.
Osd Lang
Italian/Russian
Select the DVD system interface language of the player
Captions
On/Off
Loge Type
Select display or hidden the subtitle of the disc (needing the disc backing)
Default
Captured
Display the default logo type
The Logo type is the grabbing picture of the consumer.
18
Function Operation
Audio Setup Page
DOWNMIX
LT/RT Dolby stereo, distributing the sound from the middle and the surround channels to the left and right stereo.
Stereo
V Surr
During disc is playing, the audio output left and right channel signal.
The left and right channels create surround sound effect
OFF
Dual Mono
The audio output 5.1 channel audio signal
(only support 5.1ch DVD disc)
Stereo/L-Mono
R-Mono/Mix-Mono
This entry is the selection of Dolby digital channel setup
Preference Setup Page
Preference Page can only be set up when the disc exiting from compartment and under no disc status.
- -Preference Setup Page- -
Tv Type Ntsc
PBC Off
Audio Chi
PAL
Multi
Subtitle Chi
Disc Menu Chi
NTSC
Parental
Country Region Chn
Default
To Preference setup Page
TV Type
PAL/AUTO/NTSC Setup the type of the video system
(This system is recommended to set up NTSC mode).
Audio
English/Chinese/French/Swedish/Italian/Russian/German/Spaish/Portuguese/Others
It select the language of the sound when disc is playing(needing disc backing)
19
Function Operation
Subtitle
English/Chinese/French/Swedish/Italian/Russian/German/Spaish/Portuguese/Others
It select the language of the subtitle on the disc(needing disc backing)
Disc Menu
English/Chinese/French/Swedish/Italian/Russian/German/Spaish/Portuguese/Others
It select the language of the disc menu(needing disc backing)
Parental
1 KID SAF/2 G/3 PG
/
4 PG 13/5 PGR/6 R
/
7 NC17/8 ADULT
It set the locking level of the disc menu.
Default
Reset
Resumes the function setup column to the original status of player before delivery from the plant.
Note: while the icon sound/caption//language selected, the icon” / ” shown in the right screen, click it to select the item up or down.
Password Setup Page
Password
Select sub-item “Change” in password options and press OK to access password change page. As the figure below shows, enter the n e w a n d o l d p a s s w o r d s respectively, and press OK key to end.
The original password of the system is“1389”
Old Password
New Password
Confirm PWD
****
OK
20
Function Operation
Click the numbering key to enter the new and old password and confirm, click the icon
“
OK” to complete the setup
Exit from the Setup Menu
Press to confirm and exit from the setting menu.
21
Function Operation
The system provides bluetooth hands free communication function. If your mobile phone is bluetooth enabled, it can establish a point-to-point connection with the system, providing telephone dial up and call answering Phonebook, bluetooth music play functions.
Note: As the bluetooth modules and software of cell-phones with different brands are different, some functions may be different or even not compatible with other systems in actual use. Please forgive us for this.
Touch the screen slightly to open the touch menu.
Touch the “ Home page ” icon slightly to access home page interface, and touch slightly to enter b luetooth main interface
.
Touch “Exit” icon slightly to exit from bluetooth interface.
Enter the Bluetooth interface
Phone book enable
Enter the Bluetooth setup interface
The Bluetooth music interface
Call the last incoming phone number
For using the Bluetooth handsfree function, establish the connection first. Match the main machine with the Bluetooth cell phone and touch icon：
22
Function Operation
Bluetooth main interface
(as figure shows).
Click ,open the bluetooth function of your cell phone and enable the bluetooth device searching function, and “Matching” will be displayed on the screen.
After the connection succeeded, the cell phones will display the device name (Ample
1). While connecting, the cell phone indicates the input device connection password
(0000). After matching, “Connected” will be displayed on the screen, the matched cell phone model will be displayed on the screen automatically, and icon will be displayed on the upper right part of the screen.
For manual connection, if matching succeeds, click this button to reestablish the connection after the main machine or the connection is off.
For automatic connection, if matching succeeds, the connection can be reestablished automatically after the main machine is off; and the connection can be reestablished automatically after several seconds if the connection is off.
Automatically answer means at connection mode , after hints of incoming call ring three times ,it can automatically answer the phone.
on the setup interface
Click the icon
enter the modify the password interface
Click the icon “Modify the name”, the character to be modified are shown in the display box on the right screen, you can enter the new character by means of a soft keyboard, click the icon again to confirm the operation.
23
Function Operation
If input error, click the icon to delete it. click the icon to exit.
The method of modifying the password is similar to the method of the modifying name. If modifying the password is OK and disconnect, the modified the password and name shown on the Bluetooth setup interface.
Pairing is OK
You can dial number through mobile phone or enter telephone number on the number button from screen.
Phone number list
Make a call
Clean
Hang up
Call the last incoming phone
Voice switch between the cell phone and speakers
Press number button to enter number,
Number line show input number，if input wrong number，you can click to delete one by one.
After enter telephone number,click to dial number.
123* * * * * * * *
123* * * * * * * *
123* * * * * * * *
123* * * * * * * *
Touch to hand up
24
Function Operation
During communication, Click can switch communication between car amplifier and mobile phone.
123* * * * * * * *
123* * * * * * * *
Click the “ ” to call the last incoming phone #.
When there is outside calling, In any mode,the system will automatically switch Bluetooth hand-free interface, and playing music for original mode will turn to incoming ring.
Press interface or to choose answer or refuse. If “answer ” is set up for :
“automatically answer”，after ring for three times ，it will automatically connect telephone，incoming number will be displayed in the number line.
During communication,Click can switch communication between car amplifier and mobile phone.
25
Function Operation
Click character
123* * * * * * * *
Phonebook image appears. The phonebook can used to record incoming numbers, received numbers, and missed numbers.
（It will show 5 telephone number for each style).
If the cell phone has Bluetooth music playing function, the audio o f t h e c e l l p h o n e c a n b e transferred to the vehicle speaker system to playing the music stored in the cell phone.
Click character
After matching succeeds, open the stereo connection on the cell phone and open the cell phone music playing function, and the cell phone's audio will be transferred to the vehicle speaker system.
Match and establish the connection
26
Function Operation
Play/pause
Stop
Play next track
Play previous track
Click the setting icon to exit or close the cell phone music playing function to exit from bluetooth music play.
Only support bluetooth mobile phone has “ stereo player” or“ telecontrol” function , which can operate music playing interface.
Music of the cell phone can be played only while in the bluetooth music play interface.
While in music playing state, the screen will automatically switch to spectrum interface if there is no touch operation within several seconds.
27
Function Operation
This function is available only when connected with Disc Changer .
While play CD, touch the icon “save” to copy the contents of CD into the virtual
CD.
D u r i n g c o p y i n g C D , p l a y i n g C D continues; touch the icon “EXIT” twice to
Note: During copying CD, if click the icon the disc 1---5, copying CD starts from track 1; if click the icon “my favors”, copying CD starts from the current track, the virtual CD, my favors, can store about 60 songs.
Touch the “ Home page ”icon slightly to enter home page interface,and touch slightly to enter disc changer function playing
我 的 最 爱
DISC1 00:30
TRACK001.....PLAY
TRACK002
TRACK003
TRACK004
TRACK005
TRACK006
Touch the “ Home page ” icon to enter to the home page interface，and touch other function icon to exit.
Delete
Play/pause
Next song
Previous track
Previous song
Next track
28
Function Operation
After CD contents are copied to the virtual CD. Click the icon“CDC” to play.
DISC1 00:30
DISC1 00:30
TRACK001.....PLAY
当前播放的碟
PLAY
片号
TRACK003
TRACK004
我 的 最 爱
TRACK005
TRACK006
Click the icon“ ” to select the previous track/next track to play;
Touch directly the song name to play too.
Note:the character “play” shows behind the song which is playing
29
Function Operation
If the main machine has a built-in TV module or an external TV tuner module, this operation is available (Note: actual product may vary).
Digital TV menu
Touch the screen slightly to open the touch menu.
Touch the “ Home page ” slightly icon to enter home page interface,and touch slightly to enter digital TV function
After touching the “Home page” icon to enter home page interface, touch other function icon to exit from TV function.
Note
For detailed TV function information, please refer to the operating instructions of the TV module.
30
Function Operation
When the host unit is connected with an external iPod player, the audio and video files stored in iPod player can be played by the host unit.
Touch the “ Home page ”icon slightly to enter home page interface, and touch slightly to enter ipod main interface
.
PLAYING
002/017
002/017
PLAY
PLAY
******
******
***
***
02:17
02:17
Touch the “ Home page ” icon to enter to the home page interface，and touch other function icon to exit.
Note
If the iPod player is connected when the host unit is on, the iPod player
can be detected after restarting the host unit.
Pop up/hide the number pad
Repeat the current played song
Scan and play songs in the current folder. The next song will be played after the current song has been finished for 10 seconds.
return to upper menu
Previous track
Play/pause
Play songs in the current folder at random.
Turn a page up Turn a page down
Next track
Display playing information
31
Enter the song number by the digit keyboard to play the song.
Click the digit button to select, and then click to confirm, and the selected song will be played.
Press 10+ will invalid , if you choose track above 10 ,you can press two digits directly to play.
Click to return to the upper menu, and enter to iPod main menu finally:
PLAY
******
***
02:17
The system classifies files according to the above-mentioned
6 types and stores files in the corresponding folders. Click to open a folder and play the first file.
未连接设备
播放列表
演唱者
专辑
风格
所有音乐
0.NO iPod
1.Playlists
2.Artists
3.Albums
4.Genres
5.All Music
6.Video
Playlists
Artists
Albums
Genres
All Music
Video
32
Function Operation
Function Operation
Touch the song to directly play the song.
Click to select and play the previous/next song.
Open the digit keyboard and enter the song No. to play.
Click the center of the control plate, and the play information will be displayed on the box on the right:
Play information name
**** one I love
*** baby only you
****
PLAYING 002/017
PLAY
Baby
M.N
02:17
NOW PLAY 002/017
Current play track number
/ total number
Baby opern
M.N
Special
02:17
PLAY(PAUSE)
Play time
Play/pause
33
Function Operation
Click to return to the play contents menu.
iPod player display image: iPod
KOGND
Enable disconnecting
At this mode the iPod player can not be operate
Click to return to iPod main menu, and then click 6 video item to select video play and switch to iPod operation state.
While operating iPod, select execution of the video file play, and the iPod video file image can be transferred to the host unit to play.
Enter video play interface:
Video play
Video play
Video image
34
Function Operation
While in video playing state, touch the screen slightly to open the touch menu. Touch the
“Home page” icon, and click to enter iPod operation interface, click to return to iPod main menu, and then click 1.Playlists item to exit from video play and returnto audio play.
Touch the “Home page” icon to enter to the home page interface, and touch other function icon to exit.
Because of ipod go on updating all the time , some old ipod because of software discrepancy, when in actual operation , it maybe can not be compatible with our product.
Note
When selecting the video play，you should switch to iPod operation state, and execute through iPod player operation; otherwise, sound with no image may occurs during playing.
For iPod operation, please refer to the iPod player manual.
35
Function Operation
At the back end of host unit ,there are muti-functional compound connection A and
D. both of connection should connect to audio and video input port,so that this function will valid.
Touch the screen slightly to open the touch menu.
Touch the “ Home page ” icon
AV input sightly to enter home page interface, and touch slightly to enter
AV main interface
.
Touch the “Home page” icon to enter home page interface, and touch other function icon to exit from the AV function status.
A B C
D
E F G
Note
Both the A and D interfaces of multi-function interfaces on the rear of the host unit can be used as AV input interface, b ut it can not make two AV input port at the same time, only one of them can be used.
When both the A and D interfaces are not connected to other device, please select A interface prior to B when selecting AV input; otherwise,
AV input will be disabled.
The built-in TV interface A cannot be used for AV input.
36
Function Operation
OBD (On Board Diagnostics) can read or erase the vehicle each system fault code stored in ECU and store these information in SD card, it can read the vehicle the real time information, these information are useful for repairing the vehicle.
Put the OBD in the vehicle OBD socket, a LED lights, starts the engine, power the unit on, on the main menu, click the icon”OBD” to enter the OBD interface.
Please choice CARS'series
OK
Because the unit is compatible with a number of the vehicles, if the unit is used for the first time, the pair required with the vehicle.
1、For more information about OBD, refer to OBD instruction.
2、OBD option
37
Function Operation
This function is available only when connected with GPS module.
Touch the screen slightly to open the touch menu. Touch the “ Home page ”icon slightly to enter home page interface, and touch slightly to enter navigation main interface
.
While in navigation status, press GPS button on the panel to exit from navigation status and return to other playing state.
At navigation mode
, only the corresponding touch operation functions about GPS will be available
,
If other functions needed,it must exit the navigation mode.
When switching to GPS navigation from AV/DVD/disc changer/TV/Video playing status, you can enjoy music or video in the former status in case of no navigation voice indication; and the system will automatically switch to navigation map interface in case of navigation indication. (For details, please refer to “System settings” in
“Settings”).
When switching to GPS navigation from radio/AV/DVD/disk changer/TV/Video playing state, you can enjoy music or video in the former state in case of no navigation voice indication; and the system will automatically switch to navigation map interface in case of navigation voice indication.
Under GPS navigation status and when there is music output, it is to adjust the system volume at this time.
Under the voice navigation status, it is only used for GPS navigation volume adjustment.
On Navigation state, press the button NAV more than 3 seconds to enter the PIP interface, you can watch both the DVD and navigation map at the same time(the function is available only while the input mode of DVD/AV/TV/Ipod/Video/Camera switch to navigation state)
38
Function Operation
This product also allows touch and write for destination search all operation functions of
GPS please refer to manual of GPS navigation module.
39
Function Operation
The system offers rear zone operation playing function, namely the driver can enjoy music or radio while the passage can watch DVD, TV or AV disc changer program through the dedicated headset screen on the back row without interference.
.
Open the touch menu and touch to enter to rear zone interface while in any playing status.(except NAV)
.
Touch“exit” icon to exit.
Note: in CDC state, the Rear Zone function cannot select DVD.
User can click the touch icon to select the rear zone media playing source.
Note For detailed operation of headset screen rear zone playing, please refer to headset screen manual.
40
Function Operation
According to the different model
If the host unit has a tyre pressure detection module, tyre pressure detection is available. Set the corresponding upper and lower pressure limit as well as the temperature range, and alarm will be given out, (It is available when alarm tone setting is on.) in case the set range is exceeded.
While in setting menu, click to enter tyre pressure detection interface.
SPARE
Touch “exit” icon to exit.
Setup the pressure upper limit /lower limit/unit(PSL、BAR、Kgf）。
Click the icon“pressure setup” to enter pressure setup interface.
Kgf
After click the icon“ ” or “ ”, click the icon“ ” to adjust value, then click the icon“ ” to save.
Repeat clicking the icon” ”, the pressure unit, PSL/BAR/Kgf, switches in turn,then click the icon “ ” to save
41
Function Operation
Setup the temperature upper limit/unit（ C 、F）。
Click the icon “temperature setup” to enter the temperature setup interface.
Click the icon “ ” to adjust value, then click the icon“ ” to save.
Repeat clicking the icon“ ”, the temperature unit changed between C and F, then click the icon“ ” to save.
ID code pairing
Click the icon“ID code pair” to enter the
ID code pair setup interface.
First, click the icon “Tire”, secondly, click the ID code, then click the icon “ ” to adjust the front left tire/ the front right tire/the rear left tire/the rear right tire value(0---
9,A---F), finally, click the icon“ ” to save.
Tire Swap
Click the icon “Tire swap” to enter the tire swap setup interface.
42
Function Operation
Click the icon “Confirm” to swap tire, just follow the arrow.
Open/close warning sound
Recover the last setup value
43
On this mode, if the rear camera connected, you can view the picture from the rear camera.
On the main menu, click the icon“
”to enter the rear camera interface
镜头输入
Function Operation
Click the icon “Main menu” to enter Main menu, click these icon to enter the corresponding interface.
44
Function Operation
According to the different model
Enter “System setting” menu, and touch character to change the background color of the panel buttons.
Numerical value of red，green，blue can be adjusted to change LED color of the panel ,Click icon to adjust.
Operate the direction cursor to move the light ring to select the background color.
127
120
0
To u c h d i r e c t l y t o s e l e c t background color, and click t to store the selected background color.
45
Function Operation
According to the different model
Function implemented qualification
：
1、Steering wheel learning function is the same with the original steering wheel which not bus-mastering.
2、 Key-press of original steering wheel must adopt the control way of voltage inputting. (when you operate each Key-press, enter each voltage into original sounder port )
3、When installation, find the three sorts of wires of original car steering wheel keys, one is its ground wire, one is its keys controlling wire(2 strips for some cars) and the last is its battary wire(+5V or +10V),then connect them to corresponding steering wheel wires of our host.
(When pull out the connector of audio host of original car, and original car steering wheel keys still power on, there is no need to connect extra battery; otherwise, you need to connect them to the output(+5V or +10V) of our host steering wires. Use the
“Key control wire 1”first when connecting the keys controlling wire, if normal control, please choose the “Key control wire 2” and relearn for use.)
Mode test
Release the buttons in the steering wheel, click the icon“Mode Test” to test.
While in setting menu, click
“Control calibration” icon and click to enter steering
wheel calibration.
Mode test
Press any button in the steering wheel for more than 3 seconds
Steering wheel mode test
Press any key of the steering wheel to confirm the steering wheel state.
按键学习
请在屏上选择所要学习的功能
Identify Button
Select the icon to be identified
46
Function Operation
Click the desired function key on the screen first.
Identify Button
Press the corresponding button in the steering wheel for more than 3 seconds
Press the corresponding button on the steering wheel.
Identify Button
Select the another button
After training, the system will indicate the training of the next function key. Repeat these procedures until trainings of all control keys of the steering wheel are finished.
Click to end and exit, and the main machine can be controlled by using the steering wheel of the car.
Note
In fact, user can set steering wheel button function as needed. For example, click on the screen, and press the “Vol. +” key on the steering wheel to set the key as “Song +” function.
47
Touch the screen slightly to open the touch menu.
Touch the “ Home page ” icon slightly to enter home page interface, and touch slightly to enter system setting main interface.
Touch “exit” icon to exit the current menu.
Click to enter system settings.
Touch “exit” icon to exit.
Click / character to start time display function, and the time will displayed on the lower right corner of the screen.
48
System Setup
System Setup
Spectrum Display
Click character to start spectrum display. Spectrum display mode will be automatically switched to if there is no operation for several seconds while in radio, bluetooth music, DVD, disc changer, MP3, and CD mode or playing disc without video format.
Backing a Car Function
Click character to start reverse function. If radar and camera are connected, the screen will display the reverse state information when proceeding to reverse gear.
When shutting down the panel, pull out/insert the car key again, and the screen will be on automatically to display the backing a car image. After backing a car, the screen will be off automatically to enter standby state.
Displays when backing car radar and camera are connected.
Car Backing
Camera display
1.5
M
49
Displays when car backing radar is connected.
Click the icon“ ” to enable the optical sensor function, the unit will control automatically the brightness of the
Music During Navigation:
Click character to start music navigation function.
While in navigation, the system will automatically play and switch to audio of the function state before navigation if there is no operation and navigation voice output for several seconds.
Navigation AV:
Click character to start navigation AV function.
While in navigation state, the system will automatically play and switch to AV of the function state before navigation if there is no operation and navigation voice output for several seconds.
50
System Setup
System Setup
Button Tone:
Click character to start button tone function, which allows corresponding button tone when you click a screen icon and press a button.
33
Click “ Video settings” icon to enter audio settings.
Background image
Touch to adjust the brightness, chroma and contrast of the image.
50
50
Click “Audio settings” icon to enter audio settings.
50
Touch the icon
treble/middle/bass”, touch icon to adjust the tone
Touch the icon“ ”to setup the audio to the default value.
51
各种设置
Click the icon “sound field setup” to enter the sound field setup interface.
+5 +0
+5 +5
+
4
+0
While touch the icon , the corresponding icon shown in the right corner of the screen, touch the icon to adjust the speaker volume, touch the icon
to setup the audio to the default.
Touch “exit” icon to exit .
Note “Center volume” adjustment is available only when 5.1-channel is on.
Only play 5.1ch disc , you can set up 5.1ch on turn on mode.
When play VCD ,CD ,MP3 disc ,please do turn off 5.1ch.
Click the icon “Time Setup” to enter the time setup interface.
12:00
Click to select and set the hour or minute (when the selected item f l a s h e s , t h e a d j u s t m e n t i s enabled).
12:00
System Setup
52
System Setup
Touch character to adjust hour/minute, and touch character to save the adjusted time.
Touch character ,click 12 hours mode to display “PM” character.
13 00
各种设置
PM
12 00
主页
Touch character to select
24-hour system.
Click “Control calibration” icon to enter control calibration.
Touch “exit” icon to exit .
各种设置
主页
53
Touch Screen Calibration
If deviation occurs to touch screen, you can correct the touch coordinates through “Touch calibration”.
.
Click “Touch calibration” icon to enter touch calibration
Click left
down corner
!
Use the neb to click the central point of icon to enter the next adjustment picture.
System Setup
Click right
down corner
!
!
Click right
up corner
54
System Setup
Click left
up corner
!
Click center
Over!
Note
If error occurs to touch position, you can correct the touch coordinates through “Touch calibration”.
When doing touch correction, the center point of the cross must be accurate, or else the precision of touch correction will be affected.
Steering Wheel Calibration
(For details, please refer to “14. Steering wheel calibration”)
55
During factory mode, radio antenna power switch, handbrake control, small lamp control, headset number, system reset, etc. can be set.
Click to enter AV mode, click to open the digit keyboard, and input password
“7253” as the right figure shows:
AV INPUT
System Setup
Enter to factory mode interface.
Click
to exit from factory mode interface.
System software version No.
Click the icon “Factory Setup” to enter the factory setup interface.
Radio ANT
_
P
On Off
When the radio antenna wire was used as antenna amplifier power wire, the setting shall be on, whereas the setting shall be off.
56
System Setup
Brake
Off Level Pulse
When there is no handbrake control, the setting is off.
When the handbrake control power supply uses DC power, the setting is level.
When the handbrake control power uses pulse voltage, the setting is pulse width.
Lamp
Off Level Pulse
When small lamp switch control is not necessary for button background, the setting is off.
When the small lamp control power uses DC power, the setting is level.
When the small lamp control power uses pulse voltage, the setting is pulse width.
H
_
Num
1 2
The headrest number shall be set according to the actual number, (this product supports up to 2 headsets).
Reset
Click system settings to reset to the factory state.（Under factory mode，each setup is compelling setup，it can not be restored.
Click the icon “System Information” to show the system configuration information of the unit.
Click the icon “Corporate Identity” to select the corporate identity of the unit.
57
Our products are in series, there will be slightly differences in functions and accessories according to the specific specifications, for example, GPS and backing camera. So for your own interests, please check all the accessories and packing list.
The Requirements and Method of Installation
Sensors should be inserted vertically into rear bumper as the arrow's direction. Any direction's inclination will affect the usage.
Accessories
According to the quantity installed, the positions can be as follows
：
L 2L
L
58
Accessories
The final installation position can be adjusted slightly according to your car dimensions.
2L 3L 4L 3L 2L
When backing car signal cable is connected properly, radar function will be started automatically when you backing your car.
Sensor's Effective Scope Diagram
B r a ki
S l o n g w ar ea d ow n
W a r ng a r e a a rea
If the radar is connected but the reverse camera is not connected, screen display while reversing:
59
A s f i g u r e s h o w s , e m e r a l d represents forewarning area, yellow represents amble area, and red represents stop area.
Left
Sensor1
Sensor2
Right
Sensor3
Sensor4
If both the car backing camera and radar are connected, screen display while backing a car.
1.5
M
Car Backing
Camera display
There is only camera picture if just connect the backing camera but not backing sensor when backing the car.
When head unit connect to radar car backing mode, without connecting to camera, it only show analog car photo as well As radar detecting distance on the screen .
TO_hinder camera display connect camera without connect camera
Accessories
60
Accessories
When radar backing car module is connected to left and right sensor and the distance between radar sensor and barrier is less than 1.2 but more than 0.3, monitor will display left and right radar signpost, and actual measure distance, which as shown in right picture.
When radar and all sensors have been connected and the distance between radar sensor and barrier is less than 0.3 monitor will display red signpost and STOP.
camera display connect camera
TO_hinder
STOP without connect camera
Display signpost (yellow) Display signpost (red) camera display
TO_hinder
STOP connect to camera without connecting to camera
1.When the distance between radar sensor and barrier is more than 2.0m, there will be a "BACK” on screen bottom.
2.When the distance is less than 2.0m but more than 1.2m， the distance will be displayed on screen bottom and buzzer does not work, and sensor is now working in warning area.
3.When the distance is less than 1.2m but more than 0.3m，the distance is displayed on the screen bottom and buzzer beeps, the more closer, the more frequent buzzer beeps.
Sensor is now working in slow down area.
4.When the distance is less than 0.3m， it will display “STOP!” on screen bottom, buzzer gives out continuous sound, sensor is now working in stop area.
RPA (Reverse Parking Assistant) display while the distance between the vehicle and obstacle decreases, the red bar increases; while the distance between the vehicle and obstacle increases, the green bar increases.
The unit analyzes the data from 4 sensors, and the minimum value, its meaning is the distance between the vehicle and obstacle, will be shown on the screen.
61
Detection can be affected by:
When in a smooth slope, signal can be reflected out.
When in the near of a smooth spherical object, signal can be reflected out.
When in the near of a sound absorption cotton like object, signal can be absorbed greatly.
If meeting similar special objects, reflection of the detecting wave will be blocked.
62 smooth slope smooth spherical object sound absorption cotton like object similar special objects
Accessories
Accessories
I f m e e t i n g s i m i l a r s p e c i a l circumstances, the detecting wave can not be detected. similar special circumstances
After installation, please first Confirm the function, then use.
When there is a rainstorm, or the inductor is polluted or is damaged, the detecting results will be affected.
Note
The system is only designed to help you back your car， our company will not take any responsibilities for any accident. So, please pay attention in driving.
The standard installation position of the water-proof concave camera is as shown in right figure.
The ordinary camera can be installed in any water-proof position needed.
Camera
63
8
9
10
11
12
13
14
3
4
1
2
5
6
7
15
RADI O
N A V
D V D
U S B
O S D
M A P
SETUP
O / C
C D C
FR /R E
M U T E
T V
A V
VIDEO
RTN
ENTER
Z O O M +
Z O O M -
R P T
G H I
P Q R S
A B C
J K L
T U V
L/R
BAND
S E E K
LANG
AUDIO
M E M
CAPTION
D E F
M N O
W X Y Z
I R 0 1 2
23
27
28
29
24
25
26
16
17
18
19
20
21
22
NO. Button Description of Button Function
1
Slide up(unavailable for fixed monitor)
2
3
4
5
6
7
Slide down(unavailable for fixed monitor)
DVD/ USB
RADIO
1.Switch to DVD status in any status.
2.In DVD status, press it repeatedly to switch the mode among USB/SD/
DVD mode in turn.
Switch to RADIO status.
OSD/ MAP
NAV
SETUP
1.In DVD or CDC status, turn on playing information display;
2.In navigation status, switch menu between the map and current place.
1. Select navigation status;
2.Press this button in navigation status can enter navigation main menu.
Turn on/ off the setup menu.
64
Accessories
Accessories
NO. Button Description of Button Function
8
1. In RADIO status, seek previous/next station for play; 2. Fast forward /backward in CDC status; 3.Maunal fine tuning in TV status; 4. In menu setup status,adjust
parameters. 5.In DVD status, no function for playing;
1.Adjust previous/next station step by step in RADIO status;
2. In TV status, select previous/next stationfor play; 3.In CDC status, select next/ previous track or chapter; 4. In menu setting status, select setting menu item.
5.In DVD status, no function for playing;
9
10
ENTER
1.Press it vertically as function confirm button; 2.In the fast forward/backward multiplication speed play status, press it vertically can return to normal status.
1.In RADIO status, search high frequency station semi-automatically;
2. Fast forward in CDC, DVD status; 3.In navigation status, press it to magnify map function.
1.In RADIO status, search low frequency station semi-automatically;
2. Fast backward in CDC, DVD status; 3.In navigation status, press it to minify the map.
11
Sound/
BAND
1. In RADIO status, switch band among FM1,FM2 and AM in turn;
2.Switch sound channels during VCD playing.
3. Switch the language of the disc during DVD playing.(needing disc backing)
12 Input
1.
At DVD or CDC mode c
13
14
15
18
19
16
17
SEEK/LANG
1. In TV and RADIO status, search station automatically;
2. Switch language of the disc in CDC, DVD status(needing disc backing).
RPT
In CDC, DVD status, repeat single track or all the tracks in the disc.
Number button
1. During DVD playing, select track directly;
2. When inputting characters in navigation status, you can use input method to do it.
3. In CDC playing status, press 1~6 buttons to select discs directly, press 7
O/C
MUTE
CDC
TV/AV
4.
In navigation status, when you want input the words, press the button directly to input the words.(navigation system is required.)
Open/close monitor.
(Unavailable for fixed monitor)
Turn on/off volume.
(Unavailable for fixed monitor)
Select CDC function when connect with DVD changer.
Select TV/AV function(It is valid when connect with external TV box or AV
signal).
65
25
26
27
NO. Button Description of Button Function
20
FR/RE
Switches between dual zone.
21
22
23
24
28
29
VIDEO
RTN
It is unavailable for this player.
1.During disc playing, return to main menu;
2. Return to map display menu as the main menu of navigation is turn on.
AUDIO
MEM/CAPTION
DEL
1.Select the next station in RADIO/TV status；
2.In CDC, DVD status, select next track/chapter.
1.Select the previous station in RADIO/TV status；
2.In CDC, DVD status, select previous track/chapter.
Select EQ among FLAT, CUSTOM , POP, ROCK, CLASSIC and JAZZ.
Increase volume.
Reduce volume.
1.Store the station in the RADIO or Tvstatus;
2.Switch subtitle in DVD, CDC status(needing disc backing).
Delete the words in the navigation status.
Accessories
66
Accessories
Touch “AF” character on the screen, it will open or close AF function of RDS. When
AF function of RDS is open and to touch“SEEK”, it will search AF signal of RDS automatic.
If the signal of RDS is received, one channel of M1-M6 will show the frequency of RDS.
Meanwhile,there is“ ” icon on the top right corner of screen.
Several seconds later, the channel name and style will be showed in “PS” and“PTY” status column on the screen. To choose any channel of M1-M6,the RDS message at this
Frequency will be showed in“PS”and“PTY”status column. At the same time, play the right broadcasting station program.
If there is no PTY signal, PTY will show NONE character：
NONE
If RDS signal becomes weak, it will change other frequency automatic which the signal is good enough. When RDS is close, the icon will disappear and it will not receive
RDS signal.
67
Please don't insert the coins or some metal things.
Please don't try to repair.This product is composed of lots of precise electonic commponents.
.
They will be broken or cracked if disassembled or reritted.if
the failure happens,please turn off the power supply immediately and notefy distributor.
Please don't let the display screen incur the pollution like dampness, dust, stream, lampblack, etc.
Please don't use thinner or other chemical to wipe the surface of the display screen. The dirt should be wiped off by soft cloth.
If water or other substance enters into the product
, please turn off the power supply immediately and contact the distributor
.
Please don't let the display screen be disposed in insolation.
Please turn off the power supply first when you plan to clean the machine.
Do NOT plugging and unplugging the map card and connect a wire or accessory during start-up to avoid damage to the main machine or accessory while plugging and unplugging.
If the drive mechanism is blocked, do NOT handle it by force. Please call a dedicated maintenance personnel to repair.
Check if the resistance of the speaker matcher with that of the AMP.
Please use high-quality speaker wires, and the length of the wire must be exact.
Connect jack must be inserted correspondingly.
To reduce the static noise, adjust the volume to the 2/3 of the max volume, and adjust the volume of the AMP to the distortion when with AMP.
While installing, the input and output wire must be away from the power wires and the wires of the car computer, or it will cause noise.
Precautions
68
Precautions
Discs which was dirt,dust,scratches and bending on surface will cause malfunction.
Do not place a disc on sharp object, or the disc may be scratched.
When not used, a disc should be taken out.
The following places are not suitable to place a disc.
1.Under direct sunshine.
2.Dirty,dusty and damp places.
3.Near auto heater.
4.Seats or dashboard of a car.
Do not use discs with a diameter less than 12cm (not including 12cm)or discs with irregular shapes such as heart or octangular shape,etc.
Disc cleaning: Rub the disc surface by soft damp cloth; If the disc is quite dirty, use soft damp cloth with alcohol to rub gently. Please don't use dissolvent such as gasoline, dilution or common disc cleanser, since they may damage discs.
69
Trouble Shooting
Before sending this player for service as required, please carry out inspection or small adjustment according to possible causes of occurred problems stated on the list below. It is possible that problems will be solved and this player will go back to normal operation. If you have any doubt about the problems on the list or the problem can't be solved effectively by following the remedy as instructed, please contact with our company or professional service center.
Problem
No display of LCD
No sound played
No image played
Possible Cause
Remedy
Fuse blowing
Loose wire
Communication between main machine and vehicle control system failed
Main machine control system communication failed
Too low storage battery voltage.
System's automatic protection activated
Mis-set as blank state
Replace with a new fuse
Reconnect properly.
Press Reset key of the main machine and reconnect
Press Reset key of the main machine and restart
Charge the storage battery to 12V
System in mute state
Loose sound cabinet wire
Touch the screen to restore the display
Press Mute key exit from mute state
Reconnect properly.
Damaged sound cabinet Replace with a new sound cabinet
Wrong disk position
Dirty or damaged disk
Loose/bad wire connection
Wrong use of AV input port
Wrong iPod play video file setting
Surface with label upwards on the tray
Try another disk
Reconnect properly.
Please refer to AV function operation for selecting ports
Please refer to descriptions of iPod function operation
Occasional sound
skipping
Dirty or damaged disk
Wrong installation of the main machine
Sound skipping during vibration
Wrong twisting direction of the disk changer installation screws
Try another disk
Ensure fixing the main machine securely
Place angle adjusting screws marked with V or H to the correction installation directions.
Disabled Bluetooth handsfree function
Wrong matching with the main machine
Rematch
70
Trouble Shooting
Bluetooth matching failed or unable to match
C o m p a t i b l e p r o b l e m e x i s t s between some models of cell phone
Bluetooth and the product.
Replug the car key to start up and match
Touch failed/too slow action
Touch coordinate offset
Main machine control system communication error
Recalibrate the touch coordinate
Press the Reset key to restart or restart the machine
Car reversing failed
No key tone
Wrong or bad reversing wire connection
Wrong or bad camera and radar connection
Reversing setting isn't set as “On”
The “Key tone” is set as “On”
There is music but no accompanying sound during DVD playing
Key backlight can't be lit or
Wrong language setting
Set the speaker as 5.1CH state and vehicle sound cabinet as 2CH/4CH.
The setting doesn't match the device.
The “Small lamp control” setting in factory mode is not corresponding the small lamp control wire connection state or small lamp power supply.
Reconnect
Reconnect
Access system settings, and set the reversing as “On”.
Access system settings, and set “Key tone” as “On”
Reset the language key
Set the speaker as stereo, and set the audio setting “5.1” as
“Off”.
Reset the small lamp control form
Wrong or bad handbrake connection Reconnect
Disabled handbrake
Disabled steering wheel control
Disabled tire pressure detection Not accurate
Under factory mode , grip brake control is set up to turn off mode .
Renew set up grip brake control to turn on mode.
Wrong connection between steering wheel wire and steering wheel control wire of the main machine
Reconnect
Failed connection between steering wheel and main machine
Redo steering wheel training
The way of steering wheel control can not campatible with our host.
please contact with our company after professional service for technical sustain.
Tire pressure detection setting error
Reset
Insufficient or no tire pressure detection probe battery
Replace the battery
71
The public link to your chat has been updated. You may view and manage your chat links after registration here.
Advertisement
Touchscreen interface
Bluetooth hands-free calling
DVD/VCD/CD playback
MP3/MP4 file support
Built-in GPS module
Rear zone operation playing
To turn on the main unit, insert the car key and the unit will power on automatically. If you pressed the power button to turn it off last time, press the power button again to turn it on. To turn off the unit, pull out the car key or press and hold the power button for more than 2 seconds (subject to the actual model).
During start-up, touch the screen slightly, and the "Home page" icon will be displayed on the upper left corner of the screen. Press the "Home page" icon again to enter the main page menu.
The volume adjustment key on the panel allows you to adjust the volume. Pressing the "Mute" key on the panel executes the mute function, and the mute icon will be displayed.
To use the Bluetooth hands-free function, you need to establish a connection between the main unit and your Bluetooth-enabled mobile phone. Match the main unit with your phone and follow the on-screen prompts to complete the connection.
Yes, the main unit can play audio and video files stored on an external iPod player. Connect your iPod to the main unit using the appropriate cable and select the "iPod" function to start playing.
The rear zone function allows the driver to enjoy music or radio while passengers can watch DVD, TV, or AV disc changer program on a dedicated headset screen in the back row. To use this function, select the rear zone playing mode while in any playing state (except NAV) and follow the instructions in the headset screen manual.
How to access the navigation (NAV) function?
The NAV function is available when connected to a GPS module. Access the main navigation interface by touching the “Home page” icon and then the navigation icon. To exit navigation, press the GPS button on the panel.
What is the procedure for pairing a mobile phone via Bluetooth?
Login to continue
