22B-UM001 - Rockwell Automation

22B-UM001 - Rockwell Automation
22B-UM001.book Page 1 Wednesday, January 22, 2014 11:04 AM
Adjustable
Frequency AC
Drive
FRN 1.xx - 6.xx
User Manual
www.abpowerflex.com
22B-UM001.book Page 2 Wednesday, January 22, 2014 11:04 AM
Important User Information
Solid state equipment has operational characteristics differing from those of
electromechanical equipment. Safety Guidelines for the Application, Installation
and Maintenance of Solid State Controls (Publication SGI-1.1 available from your
local Rockwell Automation sales office or online at http://
www.rockwellautomation.com/literature) describes some important differences
between solid state equipment and hard-wired electromechanical devices. Because
of this difference, and also because of the wide variety of uses for solid state
equipment, all persons responsible for applying this equipment must satisfy
themselves that each intended application of this equipment is acceptable.
In no event will Rockwell Automation, Inc. be responsible or liable for indirect or
consequential damages resulting from the use or application of this equipment.
The examples and diagrams in this manual are included solely for illustrative
purposes. Because of the many variables and requirements associated with any
particular installation, Rockwell Automation, Inc. cannot assume responsibility or
liability for actual use based on the examples and diagrams.
No patent liability is assumed by Rockwell Automation, Inc. with respect to use of
information, circuits, equipment, or software described in this manual.
Reproduction of the contents of this manual, in whole or in part, without written
permission of Rockwell Automation, Inc. is prohibited.
Throughout this manual, when necessary we use notes to make you aware of safety
considerations.
WARNING: Identifies information about practices or circumstances
that can cause an explosion in a hazardous environment, which may
lead to personal injury or death, property damage, or economic loss.
Important: Identifies information that is critical for successful application and
understanding of the product.
ATTENTION: Identifies information about practices or circumstances
that can lead to personal injury or death, property damage, or economic
loss. Attentions help you:
• identify a hazard
• avoid the hazard
• recognize the consequences
Shock Hazard labels may be located on or inside the equipment (e.g.,
drive or motor) to alert people that dangerous voltage may be present.
Burn Hazard labels may be located on or inside the equipment (e.g.,
drive or motor) to alert people that surfaces may be at dangerous
temperatures.
Allen-Bradley, Rockwell Automation, and PowerFlex are registered trademarks of Rockwell Automation, Inc.
DriveExplorer, DriveExecutive, and SCANport are trademarks of Rockwell Automation, Inc.
PLC is a registered trademark of Rockwell Automation, Inc.
PowerFlex 40 Adjustable Frequency AC Drive FRN 1.xx - 6.xx User Manual
22B-UM001.book Page 1 Wednesday, January 22, 2014 11:04 AM
Summary of Changes
The information below summarizes the changes to the PowerFlex 40
User Manual since the August 2008 release.
Manual Updates
Description of New or Updated Information
Minimum Enclosure Volume column and new footnotes added.
Drive, Fuse & Circuit Breaker Ratings topic updated.
Electronic Motor Overload Protection description updated.
Page(s)
1-9, A-2
A-1
A-4
The information below summarizes the changes to the PowerFlex 40
User Manual since the April 2008 release.
Manual Updates
Description of New or Updated Information
Description of A056 revised.
Description of A059/A062 revised.
Fault description for F3 revised.
A table row for electrical specifications added.
Graphic for the “Network Wiring” section revised.
Second last paragraph in the “Network Wiring” section revised.
Text in the “Writing (06) Logic Command Data” section revised.
Frequency source for logic command 001 of bits 14, 13, and 12 corrected.
Text in the “Writing (06) Reference” section revised.
Page(s)
3-17
3-19
4-3
A-4
C-1
C-2
C-4
C-4
C-5
Parameter Updates
The following parameters have been updated with firmware version 6.xx.
Parameter
[Relay Out Sel]
Number
A055
[Relay Out Sel]
A058, A061
Description
Page
Function of option 20, ParamControl, 3-16
changed.
Option 24, MsgControl, added.
Function of option 20, ParamControl, 3-18
changed.
Option 24, MsgControl, added.
PowerFlex 40 Adjustable Frequency AC Drive FRN 1.xx - 6.xx User Manual
Publication 22B-UM001H-EN-E
22B-UM001.book Page 2 Wednesday, January 22, 2014 11:04 AM
soc-2
The information below summarizes the changes to the PowerFlex 40
User Manual since the January 2007 release.
Manual Updates
Description of New or Updated Information
Input description and attention text for Multiple Digital Input Connection
example corrected.
New method of changing speed reference for IP66, NEMA/UL Type 4X rated
drives described.
Description for Up Arrow and Down Arrow keys revised.
Fault description for F3 revised.
Graphic for the “Network Wiring” section revised.
Descriptions for bits 6, 7, and 15 of register address 8192 (Logic Command)
updated.
New information on reading register address 8192 added.
New information on reading register address 8193 added.
Graphic for the “Connecting an RS-485 Network” section corrected.
New method for inverting sign of PID error added.
Page(s)
1-22
2-2
2-4
4-3
C-1
C-4
C-4
C-5
D-4
F-6
New Parameter
The following parameter has been added with firmware version 5.xx.
Parameter
[PID Invert Error]
Number
A167
Description
New
Page
3-44
Parameter Updates
The following parameters have been updated with firmware version 5.xx.
Parameter
[Control Source]
[Start Source]
[Relay Out Sel]
[Relay Out Level]
[Opto Outx Sel]
[Opto Outx Level]
[Internal Freq]
Number
d012
P036
A055
A056
A058, A061
A059, A062
A069
[PID Trim Hi]
[PID Trim Lo]
A130
A131
Description
Options 7 and 8 added.
Description revised for option 6.
Description revised for option 20.
Description revised.
Description revised for option 20.
Description revised.
Default value for IP66, NEMA/
UL Type 4X drives is 0.0 Hz.
Default value for IP20 rated drives is
60.0 Hz.
Description revised.
Description revised.
PowerFlex 40 Adjustable Frequency AC Drive FRN 1.xx - 6.xx User Manual
Publication 22B-UM001H-EN-E
Page
3-5
3-10
3-16
3-17
3-18
3-19
3-22
3-38
3-38
22B-UM001.book Page 1 Wednesday, January 22, 2014 11:04 AM
Table of Contents
Preface
Overview
Who Should Use this Manual? . . . . . . . . .
Reference Materials . . . . . . . . . . . . . . . . .
Manual Conventions . . . . . . . . . . . . . . . . .
Drive Frame Sizes . . . . . . . . . . . . . . . . . . .
General Precautions . . . . . . . . . . . . . . . . .
Catalog Number Explanation . . . . . . . . . .
Chapter 1
P-1
P-1
P-2
P-2
P-3
P-4
Installation/Wiring
Opening the Cover . . . . . . . . . . . . . . . . . . 1-1
Mounting Considerations . . . . . . . . . . . . . 1-3
AC Supply Source Considerations . . . . . . 1-5
General Grounding Requirements . . . . . . 1-7
Fuses and Circuit Breakers . . . . . . . . . . . . 1-8
Power Wiring . . . . . . . . . . . . . . . . . . . . . 1-10
IP66, NEMA/UL Type 4X Installations . 1-14
I/O Wiring Recommendations . . . . . . . . 1-14
Start and Speed Reference Control . . . . . 1-23
EMC Instructions . . . . . . . . . . . . . . . . . . 1-25
Chapter 2
Start Up
Prepare For Drive Start-Up . . . . . . . . . . . .
Integral Keypad . . . . . . . . . . . . . . . . . . . . .
Viewing and Editing Parameters . . . . . . . .
Remote HIM Menu Structure . . . . . . . . . .
Chapter 3
2-1
2-4
2-5
2-6
Programming and Parameters
About Parameters . . . . . . . . . . . . . . . . . . . 3-1
Parameter Organization. . . . . . . . . . . . . . . 3-2
Display Group . . . . . . . . . . . . . . . . . . . . . . 3-3
Basic Program Group . . . . . . . . . . . . . . . . 3-9
Advanced Program Group. . . . . . . . . . . . 3-14
Parameter Cross Reference – by Name. . 3-45
Chapter 4
Troubleshooting
Drive Status . . . . . . . . . . . . . . . . . . . . . . . . 4-1
Faults . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-1
Fault Descriptions . . . . . . . . . . . . . . . . . . . 4-3
Common Symptoms and Corrective Actions . .
4-5
Appendix A
Supplemental Drive Information
Drive, Fuse & Circuit Breaker Ratings . . . A-1
Specifications . . . . . . . . . . . . . . . . . . . . . . A-2
Appendix B
Accessories and Dimensions
Product Selection . . . . . . . . . . . . . . . . . . . B-1
Product Dimensions . . . . . . . . . . . . . . . . . B-7
PowerFlex 40 Adjustable Frequency AC Drive FRN 1.xx - 6.xx User Manual
Publication 22B-UM001H-EN-E
22B-UM001.book Page 2 Wednesday, January 22, 2014 11:04 AM
2
Table of Contents
Appendix C
RS485 (DSI) Protocol
Network Wiring . . . . . . . . . . . . . . . . . . . . .
Parameter Configuration . . . . . . . . . . . . . .
Supported Modbus Function Codes . . . . .
Writing (06) Logic Command Data. . . . . .
Writing (06) Reference . . . . . . . . . . . . . . .
Reading (03) Logic Status Data. . . . . . . . .
Reading (03) Feedback . . . . . . . . . . . . . . .
Reading (03) Drive Error Codes . . . . . . . .
Reading (03) and Writing (06) Drive
Parameters . . . . . . . . . . . . . . . . . . . . . . .
Additional Information . . . . . . . . . . . . . . .
Appendix D
C-1
C-3
C-3
C-4
C-5
C-5
C-6
C-6
C-7
C-7
RJ45 DSI Splitter Cable
Connectivity Guidelines . . . . . . . . . . . . . . D-1
DSI Cable Accessories . . . . . . . . . . . . . . . D-2
Connecting One Temporary Peripheral . . . D-3
Connecting One Temporary Peripheral and
One Permanent Peripheral . . . . . . . . . . . D-3
Connecting Two Permanent Peripherals . . D-4
Connecting an RS-485 Network . . . . . . . . D-4
Appendix E
StepLogic™, Basic Logic and
Timer/Counter Functions
StepLogic Using Timed Steps . . . . . . . . . .
StepLogic Using Basic Logic Functions . .
Timer Function . . . . . . . . . . . . . . . . . . . . .
Counter Function . . . . . . . . . . . . . . . . . . . .
Appendix F
E-2
E-3
E-4
E-6
PID Set Up
PID Loop . . . . . . . . . . . . . . . . . . . . . . . . . . F-1
PID Reference and Feedback . . . . . . . . . . F-4
Analog PID Reference Signals . . . . . . . . . F-5
Index
PowerFlex 40 Adjustable Frequency AC Drive FRN 1.xx - 6.xx User Manual
Publication 22B-UM001H-EN-E
22B-UM001.book Page 1 Wednesday, January 22, 2014 11:04 AM
Preface
Overview
The purpose of this manual is to provide you with the basic information
needed to install, start-up and troubleshoot the PowerFlex 40 Adjustable
Frequency AC Drive.
For information on…
Who Should Use this Manual?
Reference Materials
Manual Conventions
Drive Frame Sizes
General Precautions
Catalog Number Explanation
See page…
P-1
P-1
P-2
P-2
P-3
P-4
Who Should Use this Manual?
This manual is intended for qualified personnel. You must be able to
program and operate Adjustable Frequency AC Drive devices. In
addition, you must have an understanding of the parameter settings and
functions.
Reference Materials
The following manuals are recommended for general drive information:
Title
Wiring and Grounding
Guidelines for Pulse Width
Modulated (PWM) AC Drives
Preventive Maintenance of
Industrial Control and Drive
System Equipment
Safety Guidelines for the
Application, Installation and
Maintenance of Solid State
Control
A Global Reference Guide for
Reading Schematic Diagrams
Guarding Against Electrostatic
Damage
Publication
Available Online at …
DRIVES-IN001…
DRIVES-TD001…
SGI-1.1
www.rockwellautomation.com/
literature
100-2.10
8000-4.5.2
PowerFlex 40 Adjustable Frequency AC Drive FRN 1.xx - 6.xx User Manual
Publication 22B-UM001H-EN-E
22B-UM001.book Page 2 Wednesday, January 22, 2014 11:04 AM
P-2
Overview
Manual Conventions
•
In this manual we refer to the PowerFlex 40 Adjustable Frequency
AC Drive as; drive, PowerFlex 40 or PowerFlex 40 Drive.
•
Parameter numbers and names are shown in this format:
P031 [Motor NP Volts]
Name
Number
Group
d = Display Group
P = Basic Program Group
A = Advanced Program Group
•
The following words are used throughout the manual to describe an
action:
Word
Can
Cannot
May
Must
Shall
Should
Should Not
Meaning
Possible, able to do something
Not possible, not able to do something
Permitted, allowed
Unavoidable, you must do this
Required and necessary
Recommended
Not Recommended
Drive Frame Sizes
Similar PowerFlex 40 drive sizes are grouped into frame sizes to
simplify spare parts ordering, dimensioning, etc. A cross reference of
drive catalog numbers and their respective frame sizes is provided in
Appendix B.
PowerFlex 40 Adjustable Frequency AC Drive FRN 1.xx - 6.xx User Manual
Publication 22B-UM001H-EN-E
22B-UM001.book Page 3 Wednesday, January 22, 2014 11:04 AM
Overview
P-3
General Precautions
!
ATTENTION: The drive contains high voltage capacitors which take
time to discharge after removal of mains supply. Before working on
drive, ensure isolation of mains supply from line inputs [R, S, T (L1,
L2, L3)]. Wait three minutes for capacitors to discharge to safe voltage
levels. Failure to do so may result in personal injury or death.
Darkened display LEDs is not an indication that capacitors have
discharged to safe voltage levels.
!
!
!
!
ATTENTION: Only qualified personnel familiar with adjustable
frequency AC drives and associated machinery should plan or
implement the installation, start-up and subsequent maintenance of the
system. Failure to comply may result in personal injury and/or
equipment damage.
ATTENTION: This drive contains ESD (Electrostatic Discharge)
sensitive parts and assemblies. Static control precautions are required
when installing, testing, servicing or repairing this assembly.
Component damage may result if ESD control procedures are not
followed. If you are not familiar with static control procedures,
reference A-B publication 8000-4.5.2, “Guarding Against Electrostatic
Damage” or any other applicable ESD protection handbook.
ATTENTION: An incorrectly applied or installed drive can result in
component damage or a reduction in product life. Wiring or application
errors, such as, undersizing the motor, incorrect or inadequate AC
supply, or excessive ambient temperatures may result in malfunction of
the system.
ATTENTION: The bus regulator function is extremely useful for
preventing nuisance overvoltage faults resulting from aggressive
decelerations, overhauling loads, and eccentric loads. However, it can
also cause either of the following two conditions to occur.
1. Fast positive changes in input voltage or imbalanced input voltages
can cause uncommanded positive speed changes;
2. Actual deceleration times can be longer than commanded
deceleration times
However, a “Stall Fault” is generated if the drive remains in this state
for 1 minute. If this condition is unacceptable, the bus regulator must be
disabled (see parameter A117). In addition, installing a properly sized
dynamic brake resistor will provide equal or better performance in most
cases.
PowerFlex 40 Adjustable Frequency AC Drive FRN 1.xx - 6.xx User Manual
Publication 22B-UM001H-EN-E
22B-UM001.book Page 4 Wednesday, January 22, 2014 11:04 AM
P-4
Overview
Catalog Number Explanation
1-3
4
5
6-8
22B -
A
1P5
Drive
Dash Voltage Rating Rating
9
10
11
12 (1)
N
1
1
4
Enclosure HIM Emission Class Type
Code
22B PowerFlex 40
Code
V
A
B
D
E
Voltage
120V AC
240V AC
240V AC
480V AC
600V AC
Code Rating
0
Not Filtered
1
Filtered
Ph.
1
1
3
3
3
Code Interface Module
1
Fixed Keypad
Output Current
@ 200-240V 50/60 Hz Input
Code
2P3
5P0
6P0
Code
2P3
5P0
8P0
012
017
024
033
kW (HP)
0.4 (0.5)
0.75 (1.0)
1.1 (1.5)
Amps
2.3
5.0
8.0
12
17.5
24
33
kW (HP)
0.4 (0.5)
0.75 (1.0)
1.5 (2.0)
2.2 (3.0)
3.7 (5.0)
5.5 (7.5)
7.5 (10)
Output Current
@ 380-480V 50/60 Hz Input
Output Current
@ 500-600V 50/60 Hz Input
Code
1P4
2P3
4P0
6P0
010
012
017
024
Code
1P7
3P0
4P2
6P6
9P9
012
019
(1)
kW (HP)
0.4 (0.5)
0.75 (1.0)
1.5 (2.0)
2.2 (3.0)
4.0 (5.0)
5.5 (7.5)
7.5 (10)
11 (15)
Code Purpose
AA Reserved for
thru custom firmware
ZZ
Enclosure
Panel Mount - IP20, NEMA/UL Type Open
Panel Mount - IP66, NEMA/UL Type 4X
Flange Mount - IP20, NEMA/UL Type Open
Replacement Plate Drive - IP20, NEMA/UL Type Open
- Contact factory for ordering information.
Output Current
@ 100-120V 50/60 Hz Input
Amps
1.4
2.3
4.0
6.0
10.5
12
17
24
AA
Optional
Code Version
3
No Brake IGBT
4
Standard
Code
N
C
F
H
Amps
2.3
5.0
6.0
13-14
Amps
1.7
3.0
4.2
6.6
9.9
12.2
19
kW (HP)
0.75 (1.0)
1.5 (2.0)
2.2 (3.0)
4.0 (5.0)
5.5 (7.5)
7.5 (10)
11 (15)
Position 12 of the Catalog Number now indicates drive type. All PowerFlex 40
drives are equipped with RS485 communication.
Additional accessories, options and adapters are available. See Appendix B for details.
PowerFlex 40 Adjustable Frequency AC Drive FRN 1.xx - 6.xx User Manual
Publication 22B-UM001H-EN-E
22B-UM001.book Page 1 Wednesday, January 22, 2014 11:04 AM
Chapter 1
Installation/Wiring
This chapter provides information on mounting and wiring the
PowerFlex 40 Drive.
For information on…
Opening the Cover
Mounting Considerations
AC Supply Source Considerations
See page
1-1
1-3
1-5
General Grounding Requirements 1-7
For information on…
Fuses and Circuit Breakers
Power Wiring
I/O Wiring
Recommendations
EMC Instructions
See page
1-8
1-10
1-14
1-25
Most start-up difficulties are the result of incorrect wiring. Every
precaution must be taken to assure that the wiring is done as instructed.
All items must be read and understood before the actual installation
begins.
!
ATTENTION: The following information is merely a guide for proper
installation. Rockwell Automation, Inc. cannot assume responsibility
for the compliance or the noncompliance to any code, national, local or
otherwise for the proper installation of this drive or associated
equipment. A hazard of personal injury and/or equipment damage
exists if codes are ignored during installation.
Opening the Cover
IP20, NEMA/UL Type Open
1. Press and hold in the tabs on each side of the cover.
2. Pull the cover out and up to release.
PowerFlex 40 Adjustable Frequency AC Drive FRN 1.xx - 6.xx User Manual
Publication 22B-UM001H-EN-E
22B-UM001.book Page 2 Wednesday, January 22, 2014 11:04 AM
1-2
Installation/Wiring
IP66, NEMA/UL Type 4X
!
ATTENTION: To avoid an electric shock hazard, ensure isolation of
mains supply from line inputs [R, S, T (L1, L2, L3)] and wait three
minutes for capacitors to discharge before removing the external cover.
Once the cover is removed, verify that the voltage on the bus capacitors
has discharged before performing any work on the drive. Measure the
DC bus voltage at the DC– and DC+ terminals on the Power Terminal
Block (refer to page 1-13 for Power Terminal descriptions). The voltage
must be zero.
1. Loosen the four captive cover screws.
2. Pull cover straight off chassis.
IP66, NEMA/UL Type 4X Cover Installation
1. Squarely align the cover on the chassis.
2. Lightly tighten the four captive cover screws.
3. Torque the cover screws using an alternating pattern.
1
4
1
2
3
2
3
PowerFlex 40 Adjustable Frequency AC Drive FRN 1.xx - 6.xx User Manual
Publication 22B-UM001H-EN-E
0.8 ±0.2 N-m
(7.0 ±2.0 lb.-in.)
22B-UM001.book Page 3 Wednesday, January 22, 2014 11:04 AM
Installation/Wiring
1-3
Mounting Considerations
•
Mount the drive upright on a flat, vertical and level surface.
Frame
B
C
B (IP66,
Type 4X)
•
•
•
Screw Size
M4 (#8-32)
M5 (#10-24)
Screw Torque
1.56-1.96 N-m (14-17 lb.-in.)
2.45-2.94 N-m (22-26 lb.-in.)
DIN Rail
35 mm
–
M6 (#12-24)
3.95-4.75 N-m (35-42 lb.-in.)
–
Protect the cooling fan by avoiding dust or metallic particles.
Do not expose to a corrosive atmosphere.
Protect from moisture and direct sunlight.
Minimum Mounting Clearances
Refer to Appendix B for mounting dimensions.
120 mm
(4.7 in.)
120 mm
(4.7 in.)
25 mm
(1.0 in.)
Closest object that
may restrict air flow
through the drive heat
sink and chassis
120 mm
(4.7 in.)
120 mm
(4.7 in.)
Mounting Option A
No clearance required
between drives.
Mounting Option B
Ambient Operating Temperatures
Table 1.A Enclosure and Clearance Requirements
Ambient Temperature
Minimum
Enclosure Rating
Maximum
IP20, NEMA/UL Type Open
-10°C (14°F)
Use Mounting Option A
40°C (104°F) IP66, NEMA/UL Type 4X
Use Mounting Option A
IP30, NEMA/UL Type 1(1)
Use Mounting Option B
50°C (122°F) IP20, NEMA/UL Type Open
(1)
Minimum Mounting
Clearances
Use Mounting Option B
Rating requires installation of the PowerFlex 40 IP30, NEMA/UL Type 1 option kit.
PowerFlex 40 Adjustable Frequency AC Drive FRN 1.xx - 6.xx User Manual
Publication 22B-UM001H-EN-E
22B-UM001.book Page 4 Wednesday, January 22, 2014 11:04 AM
1-4
Installation/Wiring
Debris Protection
A plastic top panel is included with the drive. Install the panel to prevent
debris from falling through the vents of the drive housing during
installation. Remove the panel for IP20, NEMA/UL Type Open
applications.
Storage
•
•
•
Store within an ambient temperature range of -40° to +85°C.
Store within a relative humidity range of 0% to 95%,
non-condensing.
Do not expose to a corrosive atmosphere.
PowerFlex 40 Adjustable Frequency AC Drive FRN 1.xx - 6.xx User Manual
Publication 22B-UM001H-EN-E
22B-UM001.book Page 5 Wednesday, January 22, 2014 11:04 AM
Installation/Wiring
1-5
AC Supply Source Considerations
Ungrounded Distribution Systems
!
ATTENTION: PowerFlex 40 drives contain protective MOVs that are
referenced to ground. These devices must be disconnected if the drive is
installed on an ungrounded or resistive grounded distribution system.
Disconnecting MOVs
To prevent drive damage, the MOVs connected to ground shall be
disconnected if the drive is installed on an ungrounded distribution
system where the line-to-ground voltages on any phase could exceed
125% of the nominal line-to-line voltage. To disconnect these devices,
remove the jumper shown in the Figures 1.1 and 1.2.
1. Turn the screw counterclockwise to loosen.
2. Pull the jumper completely out of the drive chassis.
3. Tighten the screw to keep it in place.
Figure 1.1 Jumper Location (Typical)
IP20, NEMA/UL Type Open
IP66, NEMA/UL Type 4X
Important: Tighten screw after jumper removal.
Figure 1.2 Phase to Ground MOV Removal
R/L1
Three-Phase
AC Input S/L2
T/L3
Jumper
1
2
3
4
PowerFlex 40 Adjustable Frequency AC Drive FRN 1.xx - 6.xx User Manual
Publication 22B-UM001H-EN-E
22B-UM001.book Page 6 Wednesday, January 22, 2014 11:04 AM
1-6
Installation/Wiring
Input Power Conditioning
The drive is suitable for direct connection to input power within the rated
voltage of the drive (see Appendix A). Listed in Table 1.B are certain
input power conditions which may cause component damage or
reduction in product life. If any of the conditions exist, as described in
Table 1.B, install one of the devices listed under the heading Corrective
Action on the line side of the drive.
Important: Only one device per branch circuit is required. It should be
mounted closest to the branch and sized to handle the total
current of the branch circuit.
Table 1.B Input Power Conditions
Input Power Condition
Corrective Action
Low Line Impedance (less than 1% line reactance) • Install Line Reactor(2)
• or Isolation Transformer
Greater than 120 kVA supply transformer
• or Bus Inductor – 5.5 & 11 kW
(7.5 & 15 HP) drives only
Line has power factor correction capacitors
Line has frequent power interruptions
• Install Line Reactor
• or Isolation Transformer
Line has intermittent noise spikes in excess of
6000V (lightning)
Phase to ground voltage exceeds 125% of normal
line to line voltage
Ungrounded distribution system
240V open delta configuration (stinger leg)(1)
(1)
(2)
• Remove MOV jumper to ground.
• or Install Isolation Transformer
with grounded secondary if
necessary.
• Install Line Reactor
For drives applied on an open delta with a middle phase grounded neutral system, the
phase opposite the phase that is tapped in the middle to the neutral or earth is
referred to as the “stinger leg,” “high leg,” “red leg,” etc. This leg should be identified
throughout the system with red or orange tape on the wire at each connection point.
The stinger leg should be connected to the center Phase B on the reactor. Refer to
Table B.D for specific line reactor part numbers.
Refer to Appendix B for accessory ordering information.
PowerFlex 40 Adjustable Frequency AC Drive FRN 1.xx - 6.xx User Manual
Publication 22B-UM001H-EN-E
22B-UM001.book Page 7 Wednesday, January 22, 2014 11:04 AM
Installation/Wiring
1-7
General Grounding Requirements
The drive Safety Ground (PE) must be connected to system
ground. Ground impedance must conform to the requirements of
national and local industrial safety regulations and/or electrical codes.
The integrity of all ground connections should be periodically checked.
Figure 1.3 Typical Grounding
R/L1
S/L2
T/L3
U/T1
V/T2
W/T3
SHLD
Ground Fault Monitoring
If a system ground fault monitor (RCD) is to be used, only Type B
(adjustable) devices should be used to avoid nuisance tripping.
Safety Ground -
(PE)
This is the safety ground for the drive that is required by code. One of
these points must be connected to adjacent building steel (girder, joist), a
floor ground rod or bus bar. Grounding points must comply with national
and local industrial safety regulations and/or electrical codes.
Motor Ground
The motor ground must be connected to one of the ground terminals on
the drive.
Shield Termination - SHLD
Either of the safety ground terminals located on the power terminal
block provides a grounding point for the motor cable shield. The motor
cable shield connected to one of these terminals (drive end) should also
be connected to the motor frame (motor end). Use a shield terminating or
EMI clamp to connect the shield to the safety ground terminal. The
conduit box option may be used with a cable clamp for a grounding point
for the cable shield.
When shielded cable is used for control and signal wiring, the shield
should be grounded at the source end only, not at the drive end.
PowerFlex 40 Adjustable Frequency AC Drive FRN 1.xx - 6.xx User Manual
Publication 22B-UM001H-EN-E
22B-UM001.book Page 8 Wednesday, January 22, 2014 11:04 AM
1-8
Installation/Wiring
RFI Filter Grounding
Using single phase drives with integral filter, or an external filter with
any drive rating, may result in relatively high ground leakage currents.
Therefore, the filter must only be used in installations with grounded
AC supply systems and be permanently installed and solidly
grounded (bonded) to the building power distribution ground. Ensure
that the incoming supply neutral is solidly connected (bonded) to the
same building power distribution ground. Grounding must not rely on
flexible cables and should not include any form of plug or socket that
would permit inadvertent disconnection. Some local codes may require
redundant ground connections. The integrity of all connections should be
periodically checked.
Fuses and Circuit Breakers
The PowerFlex 40 does not provide branch short circuit protection. This
product should be installed with either input fuses or an input circuit
breaker. National and local industrial safety regulations and/or electrical
codes may determine additional requirements for these installations.
!
ATTENTION: To guard against personal injury and/or equipment
damage caused by improper fusing or circuit breaker selection, use only
the recommended line fuses/circuit breakers specified in this section.
Fusing
The PowerFlex 40 has been UL tested and approved for use with input
fuses. The ratings in the table that follows are the minimum
recommended values for use with each drive rating. The devices listed in
this table are provided to serve as a guide.
Bulletin 140M (Self-Protected Combination Controller)/UL489
Circuit Breakers
When using Bulletin 140M or UL489 rated circuit breakers, the
guidelines listed below must be followed in order to meet the NEC
requirements for branch circuit protection.
•
•
Bulletin 140M can be used in single and group motor applications.
Bulletin 140M can be used up stream from the drive without the
need for fuses.
PowerFlex 40 Adjustable Frequency AC Drive FRN 1.xx - 6.xx User Manual
Publication 22B-UM001H-EN-E
22B-UM001.book Page 9 Wednesday, January 22, 2014 11:04 AM
Installation/Wiring
1-9
Table 1.C Minimum Recommended Branch Circuit Protective Devices
Voltage
Rating
Drive Rating
kW (HP)
Recommended Min. Enclosure
Fuse Rating(1) 140M Motor
Amps
Protectors(2) (3) MCS Contactors Volume(4)
Catalog No.
Catalog No.
Inches3
120V AC –
1-Phase
0.4 (0.5)
0.75 (1.0)
1.1 (1.5)
15
35
40
140M-C2E-C16 100-C12
140M-D8E-C20 100-C23
140M-F8E-C32 100-C37
1655
1655
1655
240V AC –
1-Phase
0.4 (0.5)
0.75 (1.0)
1.5 (2.0)
2.2 (3.0)
10
20
30
40
140M-C2E-B63
140M-C2E-C16
140M-D8E-C20
140M-F8E-C32
100-C09
100-C12
100-C23
100-C37
1655
1655
1655
2069
240V AC –
3-Phase
0.4 (0.5)
0.75 (1.0)
1.5 (2.0)
2.2 (3.0)
3.7 (5.0)
5.5 (7.5)
7.5 (10.0)
6
10
15
25
30
40
60
140M-C2E-B40
140M-C2E-C10
140M-C2E-C16
140M-C2E-C16
140M-F8E-C25
140M-F8E-C32
140M-G8E-C45
100-C07
100-C09
100-C12
100-C23
100-C23
100-C37
100-C60
1655
1655
1655
1655
1655
2069
2069
480V AC –
3-Phase
0.4 (0.5)
0.75 (1.0)
1.5 (2.0)
2.2 (3.0)
4.0 (5.0)
5.5 (7.5)
7.5 (10.0)
11 (15)
3
6
10
15
20
25
30
50
140M-C2E-B25
140M-C2E-B40
140M-C2E-B63
140M-C2E-C10
140M-C2E-C16
140M-D8E-C20
140M-D8E-C20
140M-F8E-C32
100-C07
100-C07
100-C09
100-C09
100-C23
100-C23
100-C23
100-C43
1655
1655
1655
1655
1655
2069
2069
2069
600V AC –
3-Phase
0.75 (1.0)
1.5 (2.0)
2.2 (3.0)
4.0 (5.0)
5.5 (7.5)
7.5 (10.0)
11 (15)
6
6
10
15
20
25
40
140M-C2E-B25
140M-C2E-B40
140M-D8E-B63
140M-D8E-C10
140M-D8E-C16
140M-D8E-C16
140M-F8E-C25
100-C09
100-C09
100-C09
100-C09
100-C16
100-C23
100-C30
1655
1655
1655
1655
2069
2069
2069
(1)
(2)
(3)
(4)
Recommended Fuse Type: UL Class J, CC, T or Type BS88; 600V (550V) or equivalent.
The AIC ratings of the Bulletin 140M Motor Protector Circuit Breakers may vary. See Bulletin 140M
Motor Protection Circuit Breakers Application Ratings.
Manual Self-Protected (Type E) Combination Motor Controller, UL listed for 208 Wye or Delta, 240
Wye or Delta, 480Y/277 or 600Y/347. Not UL listed for use on 480V or 600V Delta/Delta, corner
ground, or high-resistance ground systems.
When using a Manual Self-Protected (Type E) Combination Motor Controller, the drive must be
installed in a ventilated or non-ventilated enclosure with the minimum volume specified in this
column. Application specific thermal considerations may require a larger enclosure.
PowerFlex 40 Adjustable Frequency AC Drive FRN 1.xx - 6.xx User Manual
Publication 22B-UM001H-EN-E
22B-UM001.book Page 10 Wednesday, January 22, 2014 11:04 AM
1-10
Installation/Wiring
Power Wiring
!
!
ATTENTION: National Codes and standards (NEC, VDE, BSI, etc.)
and local codes outline provisions for safely installing electrical
equipment. Installation must comply with specifications regarding wire
types, conductor sizes, branch circuit protection and disconnect
devices. Failure to do so may result in personal injury and/or equipment
damage.
ATTENTION: To avoid a possible shock hazard caused by induced
voltages, unused wires in the conduit must be grounded at both ends.
For the same reason, if a drive sharing a conduit is being serviced or
installed, all drives using this conduit should be disabled. This will help
minimize the possible shock hazard from “cross coupled” power leads.
Motor Cable Types Acceptable for 200-600 Volt Installations
A variety of cable types are acceptable for drive installations. For many
installations, unshielded cable is adequate, provided it can be separated
from sensitive circuits. As an approximate guide, allow a spacing of 0.3
meters (1 foot) for every 10 meters (32.8 feet) of length. In all cases,
long parallel runs must be avoided. Do not use cable with an insulation
thickness less than 15 mils (0.4 mm/0.015 in.). Do not route more than
three sets of motor leads in a single conduit to minimize “cross talk”. If
more than three drive/motor connections per conduit are required,
shielded cable must be used.
UL installations in 50°C ambient must use 600V, 75°C or 90°C wire.
UL installations in 40°C ambient should use 600V, 75°C or 90°C wire.
Use copper wire only. Wire gauge requirements and recommendations
are based on 75 degree C. Do not reduce wire gauge when using higher
temperature wire.
Unshielded
THHN, THWN or similar wire is acceptable for drive installation in dry
environments provided adequate free air space and/or conduit fill rates
limits are provided. Do not use THHN or similarly coated wire in wet
areas. Any wire chosen must have a minimum insulation thickness of 15
mils and should not have large variations in insulation concentricity.
Shielded/Armored Cable
Shielded cable contains all of the general benefits of multi-conductor
cable with the added benefit of a copper braided shield that can contain
much of the noise generated by a typical AC Drive. Strong consideration
for shielded cable should be given in installations with sensitive
equipment such as weigh scales, capacitive proximity switches and other
devices that may be affected by electrical noise in the distribution
system. Applications with large numbers of drives in a similar location,
imposed EMC regulations or a high degree of communications /
networking are also good candidates for shielded cable.
PowerFlex 40 Adjustable Frequency AC Drive FRN 1.xx - 6.xx User Manual
Publication 22B-UM001H-EN-E
22B-UM001.book Page 11 Wednesday, January 22, 2014 11:04 AM
Installation/Wiring
1-11
Shielded cable may also help reduce shaft voltage and induced bearing
currents for some applications. In addition, the increased impedance of
shielded cable may help extend the distance that the motor can be
located from the drive without the addition of motor protective devices
such as terminator networks. Refer to Reflected Wave in “Wiring and
Grounding Guidelines for PWM AC Drives,” publication
DRIVES-IN001A-EN-P.
Consideration should be given to all of the general specifications
dictated by the environment of the installation, including temperature,
flexibility, moisture characteristics and chemical resistance. In addition,
a braided shield should be included and be specified by the cable
manufacturer as having coverage of at least 75%. An additional foil
shield can greatly improve noise containment.
A good example of recommended cable is Belden® 295xx (xx
determines gauge). This cable has four (4) XLPE insulated conductors
with a 100% coverage foil and an 85% coverage copper braided shield
(with drain wire) surrounded by a PVC jacket.
Other types of shielded cable are available, but the selection of these
types may limit the allowable cable length. Particularly, some of the
newer cables twist 4 conductors of THHN wire and wrap them tightly
with a foil shield. This construction can greatly increase the cable
charging current required and reduce the overall drive performance.
Unless specified in the individual distance tables as tested with the drive,
these cables are not recommended and their performance against the lead
length limits supplied is not known.
Recommended Shielded Wire
Location
Rating/Type
Standard
(Option 1)
600V, 90°C (194°F) • Four tinned copper conductors with XLPE insulation.
XHHW2/RHW-2
• Copper braid/aluminum foil combination shield and tinned
Anixter
copper drain wire.
B209500-B209507,
• PVC jacket.
Belden 29501-29507,
or equivalent
Description
Standard
(Option 2)
Tray rated 600V, 90°C • Three tinned copper conductors with XLPE insulation.
(194°F) RHH/RHW-2 • 5 mil single helical copper tape (25% overlap min.) with three
Anixter OLF-7xxxxx or bare copper grounds in contact with shield.
equivalent
• PVC jacket.
Class I & II; Tray rated 600V, 90°C • Three bare copper conductors with XLPE insulation and
Division I & II (194°F) RHH/RHW-2
impervious corrugated continuously welded aluminum armor.
Anixter 7V-7xxxx-3G • Black sunlight resistant PVC jacket overall.
or equivalent
• Three copper grounds on #10 AWG and smaller.
PowerFlex 40 Adjustable Frequency AC Drive FRN 1.xx - 6.xx User Manual
Publication 22B-UM001H-EN-E
22B-UM001.book Page 12 Wednesday, January 22, 2014 11:04 AM
1-12
Installation/Wiring
Reflected Wave Protection
The drive should be installed as close to the motor as possible.
Installations with long motor cables may require the addition of external
devices to limit voltage reflections at the motor (reflected wave
phenomena). See Table 1.D for recommendations.
The reflected wave data applies to all frequencies 2 to 16 kHz.
For 240V ratings, reflected wave effects do not need to be considered.
Table 1.D Maximum Cable Length Recommendations
Reflected Wave
380-480V Ratings
(1)
Motor Insulation Rating
Motor Cable Only(1)
1000 Vp-p
15 meters (49 feet)
1200 Vp-p
40 meters (131 feet)
1600 Vp-p
170 meters (558 feet)
Longer cable lengths can be achieved by installing devices on the output of the drive.
Consult factory for recommendations.
Output Disconnect
The drive is intended to be commanded by control input signals that will
start and stop the motor. A device that routinely disconnects then
reapplies output power to the motor for the purpose of starting and
stopping the motor should not be used. If it is necessary to disconnect
power to the motor with the drive outputting power, an auxiliary contact
should be used to simultaneously disable drive control run commands.
PowerFlex 40 Adjustable Frequency AC Drive FRN 1.xx - 6.xx User Manual
Publication 22B-UM001H-EN-E
22B-UM001.book Page 13 Wednesday, January 22, 2014 11:04 AM
Installation/Wiring
1-13
Power Terminal Block
The power terminal block is covered by a finger guard. To remove:
1. Press in and hold the locking tab.
2. Slide finger guard down and out.
Replace the finger guard when wiring is complete.
Figure 1.4 Power Terminal Block (Typical)
B Frame
C Frame
R/L1 S/L2 T/L3 U/T1 V/T2 W/T3
R/L1 S/L2 T/L3 U/T1 V/T2 W/T3
DC- DC+ BR+ BR-
Terminal (1)
R/L1, S/L2
R/L1, S/L2, T/L3
U/T1
V/T2
W/T3
P2, P1
DC+, DCBR+, BR(1)
P2
P1
DC- DC+ BR+ BR-
Description
1-Phase Input
3-Phase Input
To Motor U/T1
Switch any two motor
leads to change
To Motor V/T2
=
forward direction.
To Motor W/T3
DC Bus Inductor Connection (C Frame drives only.)
The C Frame drive is shipped with a jumper between
Terminals P2 and P1. Remove this jumper only when a DC
Bus Inductor will be connected. Drive will not power up
without a jumper or inductor connected.
DC Bus Connection
Dynamic Brake Resistor Connection
Safety Ground - PE
Important: Terminal screws may become loose during shipment. Ensure that all
terminal screws are tightened to the recommended torque before applying power to
the drive.
Table 1.E Power Terminal Block Specifications
Frame
B
C
(1)
Maximum Wire Size (1) Minimum Wire Size (1) Torque
1.3 mm2 (16 AWG)
1.7-2.2 N-m (16-19 lb.-in.)
5.3 mm2 (10 AWG)
2 (8 AWG)
1.3 mm2 (16 AWG)
2.9-3.7 N-m (26-33 lb.-in.)
8.4 mm
Maximum/minimum sizes that the terminal block will accept - these are not
recommendations.
PowerFlex 40 Adjustable Frequency AC Drive FRN 1.xx - 6.xx User Manual
Publication 22B-UM001H-EN-E
22B-UM001.book Page 14 Wednesday, January 22, 2014 11:04 AM
1-14
Installation/Wiring
IP66, NEMA/UL Type 4X Installations
Use the plugs supplied with IP66, NEMA/UL Type 4X rated drives to
seal unused holes in the conduit entry plate.
Important: Completely seat the plug inner rim for the best seal.
I/O Wiring Recommendations
Motor Start/Stop Precautions
!
!
ATTENTION: A contactor or other device that routinely disconnects
and reapplies the AC line to the drive to start and stop the motor can
cause drive hardware damage. The drive is designed to use control input
signals that will start and stop the motor. If used, the input device must
not exceed one operation per minute or drive damage can occur.
ATTENTION: The drive start/stop control circuitry includes
solid-state components. If hazards due to accidental contact with
moving machinery or unintentional flow of liquid, gas or solids exist,
an additional hardwired stop circuit may be required to remove the AC
line to the drive. When the AC line is removed, there will be a loss of
any inherent regenerative braking effect that might be present - the
motor will coast to a stop. An auxiliary braking method may be
required.
Important points to remember about I/O wiring:
•
•
•
Always use copper wire.
Wire with an insulation rating of 600V or greater is recommended.
Control and signal wires should be separated from power wires by at
least 0.3 meters (1 foot).
Important: I/O terminals labeled “Common” are not referenced to the
safety ground (PE) terminal and are designed to greatly
reduce common mode interference.
!
ATTENTION: Driving the 4-20mA analog input from a voltage
source could cause component damage. Verify proper configuration
prior to applying input signals.
PowerFlex 40 Adjustable Frequency AC Drive FRN 1.xx - 6.xx User Manual
Publication 22B-UM001H-EN-E
22B-UM001.book Page 15 Wednesday, January 22, 2014 11:04 AM
Installation/Wiring
1-15
Control Wire Types
Table 1.F Recommended Control and Signal Wire(1)
Wire Type(s)(2)
Description
Belden 8760/9460
(or equiv.)
0.8 mm2 (18AWG), twisted pair, 100%
shield with drain. (1)
Belden 8770
(or equiv.)
(1)
(2)
Minimum
Insulation Rating
300V
60 degrees C
0.8 mm2 (18AWG), 3 conductor, shielded for (140 degrees F)
remote pot only.
If the wires are short and contained within a cabinet which has no sensitive circuits,
the use of shielded wire may not be necessary, but is always recommended.
Stranded or solid wire.
I/O Terminal Block
Table 1.G I/O Terminal Block Specifications
Frame
Maximum Wire Size (3) Minimum Wire Size (3) Torque
B&C
1.3 mm2 (16 AWG)
(3)
0.2 mm2 (24 AWG)
0.5-0.8 N-m (4.4-7 lb.-in.)
Maximum/minimum sizes that the terminal block will accept - these are not
recommendations.
Maximum Control Wire Recommendations
Do not exceed control wiring length of 30 meters (100 feet). Control
signal cable length is highly dependent on electrical environment and
installation practices. To improve noise immunity, the I/O terminal block
Common must be connected to ground terminal/protective earth. If using
the RS485 (DSI) port, I/O Terminal 16 should also be connected to
ground terminal/protective earth.
PowerFlex 40 Adjustable Frequency AC Drive FRN 1.xx - 6.xx User Manual
Publication 22B-UM001H-EN-E
22B-UM001.book Page 16 Wednesday, January 22, 2014 11:04 AM
1-16
Installation/Wiring
Figure 1.5 Control Wiring Block Diagram
Enable Jumper
(4)
01
02
03
SNK
SRC
04
05
06
07
08
09
+24V
11
+10V
12
13
14
Relay N.O.
Relay Common
Relay N.C.
R1
0-10V
R2
0/4-20mA
15
16
17
R3
30V DC
50mA
Non-inductive
0-10V
0-20mA
R1 R2 R3
18
19
Stop
Typical
SRC Wiring
(1)(4)
Start/Run FWD
Typical
SNK Wiring
(2)
Direction/Run REV
Digital Common
Digital Input 1
Digital Input 2
Digital Input 3
Digital Input 4
Opto Common
+24V DC
+10V DC
0-10V (or ±10V) Input
Analog Common
Pot must be
1-10k ohm
2 Watt Min.
4-20mA Input
Analog Output
Common
Opto Output 1
(3)
24V
Opto Output 2
RS485 Shield
Analog Output Select
ENBL
01 02 03 04 05 06 07 08 09
SNK
11 12 13 14 15 16 17 18 19
Enable
Jumper
(4)
RS485
(DSI)
SRC
30V DC 125V AC 240V AC
Resistive
3.0A
3.0A
3.0A
Inductive
0.5A
0.5A
0.5A
(1)
1
(1)
Important: I/O Terminal 01 is always a coast to stop
P036 [Start Source]
Stop
I/O Terminal 01 Stop
Keypad
Per P037
Coast
input except when P036 [Start Source] is set to
3-Wire
Per
P037
Per P037(4)
“3-Wire” or “Momt FWD/REV” control. In three wire
2-Wire
Per P037
Coast
control, I/O Terminal 01 is controlled by P037 [Stop
Momt FWD/REV
Per P037
Per P037(4)
Mode]. All other stop sources are controlled by P037
RS485 Port
Per P037
Coast
[Stop Mode].
Important: The drive is shipped with a jumper installed between I/O Terminals 01 and 11. Remove
this jumper when using I/O Terminal 01 as a stop or enable input.
(2)
Two wire control shown. For three wire control use a momentary input
on I/O Terminal 02 to
command a start. Use a maintained input
for I/O Terminal 03 to change direction.
(3)
When using an opto output with an inductive load such as a relay, install a recovery diode parallel
to the relay as shown, to prevent damage to the output.
(4)
When the ENBL enable jumper is removed, I/O Terminal 01 will always act as a hardware enable,
causing a coast to stop without software interpretation.
PowerFlex 40 Adjustable Frequency AC Drive FRN 1.xx - 6.xx User Manual
Publication 22B-UM001H-EN-E
22B-UM001.book Page 17 Wednesday, January 22, 2014 11:04 AM
Installation/Wiring
1-17
Table 1.H Control I/O Terminal Designations
No. Signal
Default
Description
Param.
R1
Relay N.O.
Fault
Normally open contact for output relay.
A055
R2
Relay Common
–
Common for output relay.
R3
Relay N.C.
Fault
Normally closed contact for output relay.
A055
Analog Output Select DIP 0-10V
Switch
Sets analog output to either voltage or current. Setting must match
A065 [Analog Out Sel].
Sink/Source DIP Switch
Source (SRC)
Inputs can be wired as Sink (SNK) or Source (SRC) via DIP Switch
setting.
P036 (1)
01
Stop (1)
Coast
The factory installed jumper or a normally closed
input must be present for the drive to start.
02
Start/Run FWD
Not Active
03
Direction/Run REV Not Active
Command comes from the integral keypad by default. P036, P037
To disable reverse operation, see A095 [Reverse
P036, P037,
Disable].
A095
04
Digital Common
–
For digital inputs. Electronically isolated with digital
inputs from analog I/O and opto outputs.
05
Digital Input 1
Preset Freq
Program with A051 [Digital In1 Sel].
06
Digital Input 2
Preset Freq
Program with A052 [Digital In2 Sel].
A051
A052
07
Digital Input 3
Local
Program with A053 [Digital In3 Sel].
A053
A054
08
Digital Input 4
Jog Forward
Program with A054 [Digital In4 Sel].
09
Opto Common
–
For opto-coupled outputs. Electronically isolated with
opto outputs from analog I/O and digital inputs.
11
+24V DC
–
Referenced to Digital Common.
Drive supplied power for digital inputs.
Maximum output current is 100mA.
12
+10V DC
–
P038
Referenced to Analog Common.
Drive supplied power for 0-10V external potentiometer.
Maximum output current is 15mA.
13
±10V In (2)
Not Active
For external 0-10V (unipolar) or ±10V (bipolar) input P038, A051supply (input impedance = 100k ohm) or
A054, A123,
potentiometer wiper.
A132
14
Analog Common
–
For 0-10V In or 4-20mA In. Electronically isolated
with analog inputs and outputs from digital I/O and
opto outputs.
15
4-20mA In (2)
Not Active
For external 4-20mA input supply
(input impedance = 250 ohm).
16
Analog Output
OutFreq 0-10
The default analog output is 0-10V. To covert to a
A065, A066
current value, change the Analog Output Select DIP
Switch to 0-20mA. Program with A065 [Analog Out
Sel]. Max analog value can be scaled with A066
[Analog Out High].
Maximum Load: 4-20mA = 525 ohm (10.5V)
0-10V = 1k ohm (10mA)
17
Opto Output 1
MotorRunning
Program with A058 [Opto Out1 Sel]
A058, A059,
A064
18
Opto Output 2
At Frequency
Program with A061 [Opto Out2 Sel]
A061, A062,
A064
19
RS485 (DSI) Shield –
(1)
(2)
P038, A051A054, A132
Terminal should be connected to safety ground - PE
when using the RS485 (DSI) communications port.
See Footnotes (1) and (4) on page 1-16.
0-10V In and 4-20mA In are distinct input channels and may be connected simultaneously.
Inputs may be used independently for speed control or jointly when operating in PID mode.
PowerFlex 40 Adjustable Frequency AC Drive FRN 1.xx - 6.xx User Manual
Publication 22B-UM001H-EN-E
22B-UM001.book Page 18 Wednesday, January 22, 2014 11:04 AM
1-18
Installation/Wiring
I/O Wiring Examples
Input/Output
Potentiometer
1-10k Ohm Pot.
Recommended
(2 Watt minimum)
Connection Example
P038 [Speed Reference] = 2 “0-10V Input”
Analog Input
0 to +10V, 100k ohm
impedance
4-20 mA, 250 ohm
impedance
Unipolar (Voltage)
Bipolar
Unipolar (Current)
P038 [Speed Reference] P038 [Speed Reference] P038 [Speed Reference]
= 2 “0-10V Input” and
= 2 “0-10V Input”
= 3 “4-20mA Input”
A123 [10V Bipolar Enbl]
= 1 “Bi-Polar In”
12
13
14
-/+ 10V
Common
Analog Input, PTC
For Drive Fault
13
14
+
Common
13
14
Common
+
14
15
Wire the PTC and External Resistor (typically matched to the PTC Hot
Resistance) to I/O Terminals 12, 13, 14.
Wire R2/R3 Relay Output (SRC) to I/O Terminals 5 & 11.
A051 [Digital In1 Sel] = 3 “Aux Fault”
A055 [Relay Out Sel] = 10 “Above Anlg V”
A056 [Relay Out Level] = % Voltage Trip
R2
R3
Re
RPTC
11
12
13
14
VTrip =
05
PowerFlex 40 Adjustable Frequency AC Drive FRN 1.xx - 6.xx User Manual
Publication 22B-UM001H-EN-E
RPTC (hot)
RPTC (hot) + Re
× 100
22B-UM001.book Page 19 Wednesday, January 22, 2014 11:04 AM
Installation/Wiring
Input/Output
Connection Example
2 Wire SRC Control - Internal Supply (SRC)
Non-Reversing
11
P036 [Start Source] =
2, 3 or 4
Input must be active for
Stop-Run
the drive to run. When
input is opened, the
drive will stop as
specified by P037
[Stop Mode].
If desired, a User
Supplied 24V DC
power source can be
used. Refer to the
“External Supply
(SRC)” example.
2 Wire SNK Control - Internal Supply (SNK)
Non-Reversing
1-19
External Supply (SRC)
01
02
01
02
Stop-Run
04
+24V
Common
Each digital input draws 6 mA.
01
02
Stop-Run
04
2 Wire SRC Control - Internal Supply (SRC)
Run FWD/Run REV
11
P036 [Start Source] =
2, 3 or 4
Stop-Run
Input must be active for
Forward
the drive to run. When
input is opened, the
Stop-Run
drive will stop as
Reverse
specified by P037
[Stop Mode].
If both Run Forward
and Run Reverse
inputs are closed at the
same time, an
undetermined state
could occur.
External Supply (SRC)
01
02
03
Stop-Run
Forward
01
02
03
04
Stop-Run
Reverse
+24V
Common
Each digital input draws 6 mA.
PowerFlex 40 Adjustable Frequency AC Drive FRN 1.xx - 6.xx User Manual
Publication 22B-UM001H-EN-E
22B-UM001.book Page 20 Wednesday, January 22, 2014 11:04 AM
1-20
Installation/Wiring
Input/Output
Connection Example
2 Wire SNK Control - Internal Supply (SNK)
Run FWD/Run REV
Stop-Run
Forward
01
02
03
04
Stop-Run
Reverse
3 Wire SRC Control - Internal Supply (SRC)
Non-Reversing
P036 [Start Source] = 1
Stop 11
A momentary input will
start the drive. A stop
Start
input to I/O Terminal 01
will stop the drive as
specified by P037
[Stop Mode].
External Supply (SRC)
Stop
01
02
Start
+24V
01
02
04
Common
Each digital input draws 6 mA.
3 Wire SNK Control - Internal Supply (SNK)
Non-Reversing
Stop
Start
3 Wire SRC Control - Internal Supply (SRC)
Reversing
P036 [Start Source] = 1
Stop 11
A momentary input will
start the drive. A stop
Start
input to I/O Terminal 01
will stop the drive as
Direction
specified by P037
[Stop Mode]. I/O
Terminal 03
determines direction.
01
02
03
04
External Supply (SRC)
Stop
01
02
03
01
02
03
04
Start
Direction
+24V
Common
Each digital input draws 6 mA.
PowerFlex 40 Adjustable Frequency AC Drive FRN 1.xx - 6.xx User Manual
Publication 22B-UM001H-EN-E
22B-UM001.book Page 21 Wednesday, January 22, 2014 11:04 AM
Installation/Wiring
1-21
Input/Output
Connection Example
3 Wire SNK Control - Internal Supply (SNK)
Reversing
Stop
01
02
03
04
Start
Direction
Opto Output (1 & 2)
A058 [Opto Out1 Sel]
determines
Opto-Output 1 (I/O
Terminal 17) operation.
A061 [Opto Out2 Sel]
determines
Opto-Output 2 (I/O
Terminal 18) operation.
When using
Opto-Output with an
inductive load such as
a relay, install a
recovery diode parallel
to the relay as shown,
to prevent damage to
the output.
Analog Output
A065 [Analog Out Sel]
determines analog
output type and drive
conditions.
0-10V,
1k ohm minimum
0-20mA/4-20mA,
525 ohm maximum
Opto-Output 1
17
CR
+24V
09
Common
Each Opto-Output is rated
30V DC 50 mA (Non-inductive).
A065 [Analog Out Sel] = 0 through 14
The Analog Output Select DIP Switch must be set to match the analog output
signal mode set in A065 [Analog Out Sel].
Common
+
14
16
PowerFlex 40 Adjustable Frequency AC Drive FRN 1.xx - 6.xx User Manual
Publication 22B-UM001H-EN-E
22B-UM001.book Page 22 Wednesday, January 22, 2014 11:04 AM
1-22
Installation/Wiring
Typical Multiple Drive Connection Examples
Input/Output
Connection Example
Multiple Digital
02
04
Input Connections
Customer Inputs can
be wired per
External Supply
(SRC) examples on
1-19 and 1-20.
Customer Inputs
02
04
02
04
Optional Ground Connection
When connecting a single input such as Run, Stop, Reverse or Preset Speeds to
multiple drives, it is important to connect I/O Terminal 04 common together for all
drives. If they are to be tied into another common (such as earth ground or
separate apparatus ground) only one point of the daisy chain of I/O Terminal 04
should be connected.
!
Multiple Analog
Connections
ATTENTION: Digital inputs on multiple drives should not be tied
together when using SNK (Internal Supply) mode. In SNK mode, if
power is removed from one drive, inadvertent operation of other
drives that share the same I/O Common connection may occur.
12 13 14
Remote Potentiometer
13 14
13 14
Optional Ground Connection
When connecting a single potentiometer to multiple drives it is important to
connect I/O Terminal 14 common together for all drives. I/O Terminal 14 common
and I/O Terminal 13 (potentiometer wiper) should be daisy-chained to each drive.
All drives must be powered up for the analog signal to be read correctly.
PowerFlex 40 Adjustable Frequency AC Drive FRN 1.xx - 6.xx User Manual
Publication 22B-UM001H-EN-E
22B-UM001.book Page 23 Wednesday, January 22, 2014 11:04 AM
Installation/Wiring
1-23
Start and Speed Reference Control
The drive speed command can be obtained from a number of different sources. The source is
normally determined by P038 [Speed Reference]. However, when A051 - A054 [Digital Inx Sel] is
set to option 2, 4, 5, 6, 11, 12, 13, 14, 15 and the digital input is active, or if A132 is not set to
option 0, the speed reference commanded by P038 [Speed Reference] will be overridden. See
the chart below for the override priority.
Jog Input
Enabled and Active:
A051, A052, A053
or A054 = 2, 11, 12
Drive will Start and Run
at Jog Speed.
Yes
Drive Stopped
(Not Running)
Yes
Direction comes from
I/O Terminal 03 Dir/Run REV
or
Jog Forward/Jog Reverse command
No
No
Local/Remote Input
Enabled and Active:
[Digital Inx Sel] = 5
Yes
Start, Speed and Direction commands
come from Integral Keypad.
Yes
Start, Speed and Direction commands
come from RS485 (DSI) port.
No
Comm Select Input
Enabled and Active:
[Digital Inx Sel] = 6
No
Speed commands come from 0-10V.
0-10V Override
Enabled and Active:
[Digital Inx Sel] = 13
Yes
Start and Direction
follows P036 [Start Source]
or
Bi-Polar input when enabled.
No
4-20mA Override
Enabled and Active:
[Digital Inx Sel] = 14
Speed commands come from 4-20mA.
Yes
Start and Direction
follows P036 [Start Source].
No
P038 [Speed Reference]
= 4 or 5
Yes
Run as specified by
P038 [Speed Refernece].
Start and Direction commands come
from P036 [Start Source].
No
Run as specified by
A071-A077 [Preset Freq 1-7].
A051/A052/A053
Preset Inputs Active
Yes
Start and Direction commands come
from P036 [Start Source].
No
PID Enabled:
A132 [PID Ref Select]
≠0
Run as specified by
A132 [PID Ref Select].
Yes
Start and Direction commands come
from P036 [Start Source].
No
Run as specified by
P038 [Speed Reference].
Start and Direction commands come
from P036 [Start Source].
PowerFlex 40 Adjustable Frequency AC Drive FRN 1.xx - 6.xx User Manual
Publication 22B-UM001H-EN-E
22B-UM001.book Page 24 Wednesday, January 22, 2014 11:04 AM
1-24
Installation/Wiring
Accel/Decel Selection
The Accel/Decel rate can be obtained by a variety of methods. The
default rate is determined by P039 [Accel Time 1] and P040 [Decel Time
1]. Alternative Accel/Decel rates can be made through digital inputs,
RS485 (DSI) communications and/or parameters. See the chart below
for the override priority.
Jog Input
Enabled and Active:
A051, A052, A053
or A054 = 2, 11,12
Yes
Drive Stopped
(Not Running)
Drive will Start and Run
at Jog Speed.
Yes
Drive will use A079 [Jog Accel/Decel]
No
No
RS485 (DSI) Port
Controls Speed
Yes
Either
P039 [Accel Time 1]/P040 [Decel Time 1]
or
A067 [Accel Time 2]/A068 [Decel Time 2]
can be selected when
RS485 (DSI) port is active.
Yes
A067 [Accel Time 2]/A068 [Decel Time 2]
is active when input is active.
Yes
P039 [Accel Time 1]/P040 [Decel Time 1];
A067 [Accel Time 2]/A068 [Decel Time 2]
determined by the active
Preset Frequency.
See A070-A077 [Preset Freq 0-7]
Yes
Either
P039 [Accel Time 1]/P040 [Decel Time 1]
or
A067 [Accel Time 2]/A068 [Decel Time 2]
can be selected by the Digit 3 setting
of the Step Logic parameters.
See A140-A147 [Stp Logic 0-7]
No
Input is programmed
as "Accel 2 & Decel 2"
A051, A052, A053
or A054 = 1
No
Speed is controlled
by [Preset Freq x]
No
Speed is controlled
by Stp Logic
No
P039 [Accel Time 1]/P040 [Decel Time 1]
are used.
PowerFlex 40 Adjustable Frequency AC Drive FRN 1.xx - 6.xx User Manual
Publication 22B-UM001H-EN-E
22B-UM001.book Page 25 Wednesday, January 22, 2014 11:04 AM
Installation/Wiring
1-25
EMC Instructions
CE Conformity
Conformity with the Low Voltage (LV) Directive and Electromagnetic
Compatibility (EMC) Directive has been demonstrated using
harmonized European Norm (EN) standards published in the Official
Journal of the European Communities. PowerFlex Drives comply with
the EN standards listed below when installed according to the User
Manual.
CE Declarations of Conformity are available online at:
http://www.ab.com/certification/ce/docs.
Low Voltage Directive (73/23/EEC)
•
EN50178 Electronic equipment for use in power installations
EMC Directive (89/336/EEC)
•
EN61800-3 Adjustable speed electrical power drive systems Part 3:
EMC product standard including specific test methods.
General Notes
•
•
•
•
If the plastic top panel is removed or the optional conduit box is not
installed, the drive must be installed in an enclosure with side
openings less than 12.5 mm (0.5 in.) and top openings less than 1.0
mm (0.04 in.) to maintain compliance with the LV Directive.
The motor cable should be kept as short as possible in order to avoid
electromagnetic emission as well as capacitive currents.
Use of line filters in ungrounded systems is not recommended.
Conformity of the drive with CE EMC requirements does not
guarantee an entire machine installation complies with CE EMC
requirements. Many factors can influence total machine/installation
compliance.
PowerFlex 40 Adjustable Frequency AC Drive FRN 1.xx - 6.xx User Manual
Publication 22B-UM001H-EN-E
22B-UM001.book Page 26 Wednesday, January 22, 2014 11:04 AM
1-26
Installation/Wiring
Essential Requirements for CE Compliance
Conditions 1-3 listed below must be satisfied for PowerFlex drives to
meet the requirements of EN61800-3.
1. Grounding as described in Figure 1.6. Refer to page 1-8 for
additional grounding recommendations.
2. Output power, control (I/O) and signal wiring must be braided,
shielded cable with a coverage of 75% or better, metal conduit or
equivalent attenuation.
3. Allowable cable length in Table 1.I is not exceeded.
Table 1.I Allowable Cable Length
Filter Type
EN61800-3 First Environment
Restricted Distribution or
Second Environment (2)
10 meters (33 feet)
10 meters (33 feet)
Integral
External - S Type(1)
External - L Type(1) 100 meters (328 feet)
EN61800-3 First Environment
Unrestricted Distribution (3)
1 meter (3 feet)
1 meter (3 feet)
5 meters (16 feet)
(1) Refer to Appendix B for details on optional external filters.
(2)
Equivalent to EN55011 Class A.
(3) Equivalent to EN55011 Class B.
Figure 1.6 Connections and Grounding
(1)
Shielded Enclosure
IP 30/NEMA 1/UL Type 1
Option Kit
(2)
EMI Filter
L1
L2
L3
L1'
L2'
L3'
EMI Fittings and Metal Conduit
U/T1
V/T2
W/T3
R/L1
S/L2
T/L3
Enclosure Ground Connection
Shielded Motor Cable
Building Structure Steel
(1)
(2)
First Environment Unrestricted Distribution installations require a shielded enclosure.
Keep wire length as short as possible between the enclosure entry point and the EMI
filter.
Integral EMI filters are available on 240V, 1-Phase drives.
PowerFlex 40 Adjustable Frequency AC Drive FRN 1.xx - 6.xx User Manual
Publication 22B-UM001H-EN-E
22B-UM001.book Page 27 Wednesday, January 22, 2014 11:04 AM
Installation/Wiring
1-27
EN61000-3-2
•
•
0.75 kW (1 HP) 240V 1-Phase and 3-Phase drives and 0.37 kW (0.5
HP) 240V 1-Phase drives are suitable for installation on a private low
voltage power network. Installations on a public low voltage power
network may require additional external harmonic mitigation.
Other drive ratings meet the current harmonic requirements of
EN61000-3-2 without additional external mitigation.
PowerFlex 40 Adjustable Frequency AC Drive FRN 1.xx - 6.xx User Manual
Publication 22B-UM001H-EN-E
22B-UM001.book Page 28 Wednesday, January 22, 2014 11:04 AM
1-28
Installation/Wiring
Notes:
PowerFlex 40 Adjustable Frequency AC Drive FRN 1.xx - 6.xx User Manual
Publication 22B-UM001H-EN-E
22B-UM001.book Page 1 Wednesday, January 22, 2014 11:04 AM
Chapter 2
Start Up
This chapter describes how to start up the PowerFlex 40 Drive. To
simplify drive setup, the most commonly programmed parameters are
organized in a single Basic Program Group.
Important: Read the General Precautions section before proceeding.
!
ATTENTION: Power must be applied to the drive to perform the
following start-up procedures. Some of the voltages present are at
incoming line potential. To avoid electric shock hazard or damage to
equipment, only qualified service personnel should perform the
following procedure. Thoroughly read and understand the procedure
before beginning. If an event does not occur while performing this
procedure, Do Not Proceed. Remove All Power including user
supplied control voltages. User supplied voltages may exist even when
main AC power is not applied to the drive. Correct the malfunction
before continuing.
Prepare For Drive Start-Up
Before Applying Power to the Drive
❏ 1. Confirm that all inputs are connected to the correct terminals and are
secure.
❏ 2. Verify that AC line power at the disconnect device is within the rated
value of the drive.
❏ 3. Verify that any digital control power is 24 volts.
❏ 4. Verify that the Sink (SNK)/Source (SRC) Setup DIP Switch is set to
match your control wiring scheme. See Figure 1.5 on page 1-16 for
location.
Important: The default control scheme is Source (SRC). The Stop
terminal is jumpered (I/O Terminals 01 and 11) to allow
starting from the keypad. If the control scheme is changed
to Sink (SNK), the jumper must be removed from I/O
Terminals 01 and 11 and installed between I/O Terminals
01 and 04.
❏ 5. Verify that the Stop input is present or the drive will not start.
Important: If I/O Terminal 01 is used as a stop input, the jumper
between I/O Terminals 01 and 11 must be removed.
PowerFlex 40 Adjustable Frequency AC Drive FRN 1.xx - 6.xx User Manual
Publication 22B-UM001H-EN-E
22B-UM001.book Page 2 Wednesday, January 22, 2014 11:04 AM
2-2
Start Up
Applying Power to the Drive
❏ 6. Apply AC power and control voltages to the drive.
❏ 7. Familiarize yourself with the integral keypad features (see page 2-4)
before setting any Program Group parameters.
If a fault appears on power up, refer to Fault Descriptions on page 4-3
for an explanation of the fault code.
Start, Stop, Direction and Speed Control
Factory default parameter values allow the drive to be controlled from
the integral keypad. No programming is required to start, stop, change
direction and control speed directly from the integral keypad.
Important: To disable reverse operation, see A095 [Reverse Disable].
Changing the Speed Reference of an IP66, NEMA/UL Type 4X rated
drive
When a Display Group parameter, for example, d001 [Output Freq] is
displayed, and P038 [Speed Ref] is set to A069 [Internal Freq], you can
change the internal frequency using the Up Arrow and Down Arrow
keys.
VOLTS
AMPS
HERTZ
RUN
FWD
REV
VOLTS
AMPS
HERTZ
PROGRAM
FAULT
When the internal frequency is being adjusted, its value is displayed and
the Hertz LED flashes. Any changes are saved immediately. The display
then returns to the Display Group parameter previously shown.
TIP: By default, the speed reference of an IP66, NEMA/UL Type 4X
rated drive is set to the internal frequency, A069 [Internal Freq].
PowerFlex 40 Adjustable Frequency AC Drive FRN 1.xx - 6.xx User Manual
Publication 22B-UM001H-EN-E
22B-UM001.book Page 3 Wednesday, January 22, 2014 11:04 AM
Start Up
2-3
TIP: You can also change the speed reference by editing the parameter
A069 [Internal Freq] in program mode. For details on how to enter the
program mode, see Viewing and Editing Parameters on page 2-5.
Note: The default value of A069 [Internal Freq] is 0 Hz. For IP20 rated
PowerFlex 40 drives, the default value of this parameter is 60 Hz.
Variable Torque Fan/Pump Applications
For improved motor tuning performance when using a premium efficient
motor on a variable torque load, set A084 [Boost Select] to option 2
“35.0, VT”.
PowerFlex 40 Adjustable Frequency AC Drive FRN 1.xx - 6.xx User Manual
Publication 22B-UM001H-EN-E
22B-UM001.book Page 4 Wednesday, January 22, 2014 11:04 AM
2-4
Start Up
Integral Keypad
➋
➊
➌
RUN
FWD
REV
➎
Basic Program Group
Consists of most commonly used
programmable functions.
➑
➐
Description
Display Group (View Only)
Consists of commonly viewed drive operating
conditions.
FAULT
PROGRAM
➍
➏
Menu
VOLTS
AMPS
HERTZ
➒
Advanced Program Group
Consists of remaining programmable functions.
Fault Designator
Consists of list of codes for specific fault
conditions. Displayed only when fault is present.
No. LED
➊ Run/Direction
Status
LED State
Steady Red
Flashing Red
➋
Alphanumeric
Display
Steady Red
Flashing Red
➌
➍
➎
➏
➐
Displayed Units
Steady Red
Description
Indicates drive is running and commanded motor direction.
Drive has been commanded to change direction. Indicates
actual motor direction while decelerating to zero.
Indicates parameter number, parameter value, or fault code.
Single digit flashing indicates that digit can be edited.
All digits flashing indicates a fault condition.
Indicates the units of the parameter value being displayed.
Program Status
Steady Red
Indicates parameter value can be changed.
Fault Status
Flashing Red
Indicates drive is faulted.
Pot Status
Steady Green
Indicates potentiometer on Integral Keypad is active.(1)
Start Key Status Steady Green
No. Key
➑
Name
Escape
Select
Up Arrow
Down Arrow
Enter
➒
Potentiometer(1)
Start
Reverse
Stop
(1)
Indicates Start key on Integral Keypad is active.
The Reverse key is also active unless disabled by A095
[Reverse Disable].
Description
Back one step in programming menu.
Cancel a change to a parameter value and exit Program Mode.
Advance one step in programming menu.
Select a digit when viewing parameter value.
Scroll through groups and parameters.
Increase/decrease the value of a flashing digit.
Used to adjust internal frequency of IP66, NEMA/UL Type 4X
rated drives only when a Display Group parameter is shown
and P038 [Speed Reference] is set to internal frequency,
A069 [Internal Freq].
Advance one step in programming menu.
Save a change to a parameter value.
Used to control speed of drive. Default is active.
Controlled by parameter P038 [Speed Reference].
Used to start the drive. Default is active.
Controlled by parameter P036 [Start Source].
Used to reverse direction of the drive. Default is active.
Controlled by parameters P036 [Start Source] and A095
[Reverse Disable].
Used to stop the drive or clear a fault.
This key is always active.
Controlled by parameter P037 [Stop Mode].
IP66, NEMA/UL Type 4X rated drives are not equipped with a potentiometer.
PowerFlex 40 Adjustable Frequency AC Drive FRN 1.xx - 6.xx User Manual
Publication 22B-UM001H-EN-E
22B-UM001.book Page 5 Wednesday, January 22, 2014 11:04 AM
Start Up
2-5
Viewing and Editing Parameters
The last user-selected Display Group parameter is saved when power is removed and is displayed by
default when power is reapplied.
The following is an example of basic integral keypad and display functions. This example provides basic
navigation instructions and illustrates how to program the first Program Group parameter.
Step
Key(s)
1. When power is applied, the last user-selected
Display Group parameter number is briefly
displayed with flashing characters. The display
then defaults to that parameter’s current value.
(Example shows the value of d001 [Output
Freq] with the drive stopped.)
Example Displays
VOLTS
AMPS
HERTZ
PROGRAM
2. Press Esc once to display the Display Group
parameter number shown on power-up. The
parameter number will flash.
FAULT
VOLTS
AMPS
HERTZ
PROGRAM
FAULT
3. Press Esc again to enter the group menu. The
group menu letter will flash.
VOLTS
AMPS
HERTZ
4. Press the Up Arrow or Down Arrow to scroll
through the group menu (d, P and A).
or
5. Press Enter or Sel to enter a group. The right
digit of the last viewed parameter in that group
will flash.
or
6. Press the Up Arrow or Down Arrow to scroll
through the parameters that are in the group.
or
7. Press Enter or Sel to view the value of a
parameter. If you do not want to edit the value,
press Esc to return to the parameter number.
or
8. Press Enter or Sel to enter program mode to
edit the parameter value. The right digit will
flash and the Program LED will illuminate if the
parameter can be edited.
9. Press the Up Arrow or Down Arrow to change
the parameter value. If desired, press Sel to
move from digit to digit or bit to bit. The digit or
bit that you can change will flash.
PROGRAM
FAULT
VOLTS
AMPS
HERTZ
PROGRAM
FAULT
VOLTS
AMPS
HERTZ
PROGRAM
FAULT
or
VOLTS
AMPS
HERTZ
PROGRAM
FAULT
or
10. Press Esc to cancel a change. The digit will
stop flashing, the previous value is restored and
the Program LED will turn off.
Or
Press Enter to save a change. The digit will stop
flashing and the Program LED will turn off.
VOLTS
AMPS
HERTZ
PROGRAM
11. Press Esc to return to the parameter list.
Continue to press Esc to back out of the
programming menu.
If pressing Esc does not change the display,
then d001 [Output Frequency] is displayed.
Press Enter or Sel to enter the group menu.
FAULT
VOLTS
AMPS
HERTZ
PROGRAM
FAULT
PowerFlex 40 Adjustable Frequency AC Drive FRN 1.xx - 6.xx User Manual
Publication 22B-UM001H-EN-E
22B-UM001.book Page 6 Wednesday, January 22, 2014 11:04 AM
2-6
Start Up
The Basic Program Group (page 3-9) contains the most commonly changed parameters.
Remote HIM Menu Structure
The Menu Structure below can be accessed through the following
Human Interface Module options:
HIM Option
Remote Panel Mount Small, LCD Display
Remote Handheld, LCD Display
Catalog Number
22-HIM-C2S
22-HIM-A3
User
Display
Main Menu:
Esc
Faults
Device Status
Device Version
Diagnostics
HIM Reference
Increase/Decrease Hz
Sel
Sel
PowerFlex 40
Product Data
Series
Firmware
Group Name
Parameter Number Name
Parameter Number Name
Parameter Number Name
Groups
Linear List
Changed Params
Parameters
View Fault Queue
Clear Faults
Clear Fault Queue
Device Status
STS1
STS2
STS3
STS4
Sel
Sel
PowerFlex 40
Connected DSI Devices
Device Select
Parameter Name
Value Screen
Limits Screen
Sel
HIM CopyCat
Memory Storage
Sel
Parameters
Device Version
HIM Setup
Sel
Press
Sel
Device Cat. No.
Device Name
Series
Firmware
to move between main menu tabs
to select a tab or menu item
Press
Press
Press
Device -> HIM
Device <- HIM
Delete File
to move between menu items
Esc
to move 1 level back in the menu structure
PowerFlex 40 Adjustable Frequency AC Drive FRN 1.xx - 6.xx User Manual
Publication 22B-UM001H-EN-E
Sel
Files Screen
Stats Screen
Function
File Name
File Name
File Name
File Name
File Name
Parameters
001 Startup Display
002 Startup Param
004 User Disp Line 1
005 User Disp Line 2
006 Large Disp Param
007 LCD Contrast
008 Reset Device
009 Device Type
010 M/S Status
22B-UM001.book Page 7 Wednesday, January 22, 2014 11:04 AM
Start Up
2-7
Diagnostics Menu
When a fault trips the drive, use this menu to access detailed data about
the drive.
Option
Faults
Device Status
Device Version
Description
View fault queue or fault information, clear faults or clear fault
queue.
View status information about the drive or peripheral.
View the firmware version and hardware series of components.
Parameters Menu
Use this menu to access drive parameters. Parameters can be displayed
in groups, in a linear list, or only those changed from their defaults.
Device Select Menu
Use this menu to access the drive or peripheral that the drive is to access.
Memory Storage Menu
Drive data can be saved to, or recalled from HIM sets.
HIM sets are files stored in permanent nonvolatile HIM memory.
Option
HIM Copycat
Device -> HIM
Device <- HIM
Delete File
Description
Save data to a HIM set or load data from a HIM set to active drive
memory. A maximum of 5 HIM set can be stored.
Delete a HIM set.
HIM Setup Menu
The HIM and drive have features that you can customize.
Option
Parameters
Device Version
Description
Access parameters in HIM to set display options.
View HIM version, hardware series and firmware version
PowerFlex 40 Adjustable Frequency AC Drive FRN 1.xx - 6.xx User Manual
Publication 22B-UM001H-EN-E
22B-UM001.book Page 8 Wednesday, January 22, 2014 11:04 AM
2-8
Start Up
Notes:
PowerFlex 40 Adjustable Frequency AC Drive FRN 1.xx - 6.xx User Manual
Publication 22B-UM001H-EN-E
22B-UM001.book Page 1 Wednesday, January 22, 2014 11:04 AM
Chapter 3
Programming and Parameters
Chapter 3 provides a complete listing and description of the PowerFlex
40 parameters. Parameters are programmed (viewed/edited) using the
integral keypad. As an alternative, programming can also be performed
using DriveExplorer™ or DriveExecutive™ software, a personal
computer and a serial converter module. Refer to Appendix B for catalog
numbers.
For information on…
About Parameters
Parameter Organization
Basic Program Group
Advanced Program Group
Parameter Cross Reference – by Name
See page…
3-1
3-2
3-9
3-14
3-45
About Parameters
To configure a drive to operate in a specific way, drive parameters may
have to be set. Three types of parameters exist:
•
ENUM
ENUM parameters allow a selection from 2 or more items. Each item
is represented by a number.
•
Numeric Parameters
These parameters have a single numerical value (i.e. 0.1 Volts).
•
Bit Parameters
Bit parameters have four individual bits associated with features or
conditions. If the bit is 0, the feature is off or the condition is false. If
the bit is 1, the feature is on or the condition is true.
Some parameters are marked as follows.
= Stop drive before changing this parameter.
32
= 32 bit parameter. Parameters marked 32 bit will have two
parameter numbers when using RS485 communications and
programming software.
PowerFlex 40 Adjustable Frequency AC Drive FRN 1.xx - 6.xx User Manual
Publication 22B-UM001H-EN-E
22B-UM001.book Page 2 Wednesday, January 22, 2014 11:04 AM
3-2
Programming and Parameters
Parameter Organization
Refer to page 3-45 for an alphabetical listing of parameters.
Displa
y Gro
A
Progdravanced
m Gro
up
up
See page 3-3
Output Freq
Commanded Freq
Output Current
Output Voltage
DC Bus Voltage
Drive Status
Fault 1 Code
Fault 2 Code
Fault 3 Code
Process Display
Control Source
Contrl In Status
Dig In Status
Comm Status
Control SW Ver
Drive Type
Elapsed Run Time
Testpoint Data
Analog In 0-10V
Analog In 4-20mA
Output Power
Output Power Fctr
Drive Temp
Counter Status
Timer Status
Stp Logic Status
Torque Current
d001
d002
d003
d004
d005
d006
d007
d008
d009
d010
d012
d013
d014
d015
d016
d017
d018
d019
d020
d021
d022
d023
d024
d025
d026
d028
d029
Basic
Progra
m Gro
up
See page 3-9
Motor NP Volts
Motor NP Hertz
Motor OL Current
Minimum Freq
Maximum Freq
Start Source
Stop Mode
Speed Reference
Accel Time 1
Decel Time 1
Reset To Defalts
Voltage Class
Motor OL Ret
P031
P032
P033
P034
P035
P036
P037
P038
P039
P040
P041
P042
P043
See page 3-14
Digital In1 Sel
Digital In2 Sel
Digital In3 Sel
Digital In4 Sel
Relay Out Sel
Relay Out Level
Opto Out1 Sel
Opto Out1 Level
Opto Out2 Sel
Opto Out2 Level
Opto Out Logic
Analog Out Sel
Analog Out High
Accel Time 2
Decel Time 2
Internal Freq
Preset Freq 0
Preset Freq 1
Preset Freq 2
Preset Freq 3
Preset Freq 4
Preset Freq 5
Preset Freq 6
Preset Freq 7
Jog Frequency
Jog Accel/Decel
DC Brake Time
DC Brake Level
DB Resistor Sel
S Curve %
Boost Select
Start Boost
Break Voltage
Break Frequency
Maximum Voltage
Current Limit 1
Motor OL Select
PWM Frequency
Auto Rstrt Tries
Auto Rstrt Delay
Start At PowerUp
Reverse Disable
Flying Start En
Compensation
SW Current Trip
Process Factor
Fault Clear
Program Lock
Testpoint Sel
Comm Data Rate
Comm Node Addr
Comm Loss Action
A051
A052
A053
A054
A055
A056
A058
A059
A061
A062
A064
A065
A066
A067
A068
A069
A070
A071
A072
A073
A074
A075
A076
A077
A078
A079
A080
A081
A082
A083
A084
A085
A086
A087
A088
A089
A090
A091
A092
A093
A094
A095
A096
A097
A098
A099
A100
A101
A102
A103
A104
A105
PowerFlex 40 Adjustable Frequency AC Drive FRN 1.xx - 6.xx User Manual
Publication 22B-UM001H-EN-E
See page 3-14
Comm Loss Time
Comm Format
Language
Anlg Out Setpt
Anlg In 0-10V Lo
Anlg In 0-10V Hi
Anlg In4-20mA Lo
Anlg In4-20mA Hi
Slip Hertz @ FLA
Process Time Lo
Process Time Hi
Bus Reg Mode
Current Limit 2
Skip Frequency
Skip Freq Band
Stall Fault Time
Analog In Loss
10V Bipolar Enbl
Var PWM Disable
Torque Perf Mode
Motor NP FLA
Autotune
IR Voltage Drop
Flux Current Ref
PID Trim Hi
PID Trim Lo
PID Ref Sel
PID Feedback Sel
PID Prop Gain
PID Integ Time
PID Diff Rate
PID Setpoint
PID Deadband
PID Preload
Stp Logic 0
Stp Logic 1
Stp Logic 2
Stp Logic 3
Stp Logic 4
Stp Logic 5
Stp Logic 6
Stp Logic 7
Stp Logic Time 0
Stp Logic Time 1
Stp Logic Time 2
Stp Logic Time 3
Stp Logic Time 4
Stp Logic Time 5
Stp Logic Time 6
Stp Logic Time 7
EM Brk Off Delay
EM Brk On Delay
MOP Reset Sel
DB Threshold
Comm Write Mode
Anlg Loss Delay
Analog In Filter
PID Invert Error
A106
A107
A108
A109
A110
A111
A112
A113
A114
A115
A116
A117
A118
A119
A120
A121
A122
A123
A124
A125
A126
A127
A128
A129
A130
A131
A132
A133
A134
A135
A136
A137
A138
A139
A140
A141
A142
A143
A144
A145
A146
A147
A150
A151
A152
A153
A154
A155
A156
A157
A160
A161
A162
A163
A164
A165
A166
A167
22B-UM001.book Page 3 Wednesday, January 22, 2014 11:04 AM
Programming and Parameters
3-3
Display Group
d001 [Output Freq]
Related Parameter(s): d002, d010, P034, P035, P038
Output frequency present at T1, T2 & T3 (U, V & W).
Values
Default:
Read Only
Min/Max:
0.0/P035 [Maximum Freq]
Display:
0.1 Hz
d002 [Commanded Freq]
Related Parameter(s): d001, d013, P034, P035, P038
Value of the active frequency command. Displays the commanded frequency even if the drive is not
running.
Important: The frequency command can come from a number of sources. Refer to Start and Speed
Reference Control on page 1-23 for details.
Values
Default:
Read Only
Min/Max:
0.0/P035 [Maximum Freq]
Display:
0.1 Hz
d003 [Output Current]
The output current present at T1, T2 & T3 (U, V & W).
Values
Default:
Read Only
Min/Max:
0.00/(Drive Rated Amps × 2)
Display:
0.01 Amps
d004 [Output Voltage]
Related Parameter(s): P031, A084, A088
Output voltage present at terminals T1, T2 & T3 (U, V & W).
Values
Default:
Read Only
Min/Max:
0/Drive Rated Volts
Display:
1 VAC
d005 [DC Bus Voltage]
Present DC bus voltage level.
Values
Default:
Read Only
Min/Max:
Based on Drive Rating
Display:
1 VDC
PowerFlex 40 Adjustable Frequency AC Drive FRN 1.xx - 6.xx User Manual
Publication 22B-UM001H-EN-E
22B-UM001.book Page 4 Wednesday, January 22, 2014 11:04 AM
3-4
Programming and Parameters
Display Group (continued)
d006 [Drive Status]
Related Parameter(s): A095
Present operating condition of the drive.
Running
Forward
Accelerating
Decelerating
Values
1 = Condition True, 0 = Condition False
Bit 0
Bit 1
Bit 2
Bit 3
Default:
Read Only
Min/Max:
0/1
Display:
1
d007 [Fault 1 Code]
d008 [Fault 2 Code]
d009 [Fault 3 Code]
A code that represents a drive fault. The codes will appear in these parameters in the order they occur
(d007 [Fault 1 Code] = the most recent fault). Repetitive faults will only be recorded once.
Refer to Chapter 4 for fault code descriptions.
Values
Default:
Read Only
Min/Max:
F2/F122
Display:
F1
d010 [Process Display]
32
Related Parameter(s): d001, A099
32 bit parameter.
The output frequency scaled by A099 [Process Factor].
Output
Process
Process
Freq x Factor = Display
Values
Default:
Read Only
Min/Max:
0.00/9999
Display:
0.01 – 1
PowerFlex 40 Adjustable Frequency AC Drive FRN 1.xx - 6.xx User Manual
Publication 22B-UM001H-EN-E
22B-UM001.book Page 5 Wednesday, January 22, 2014 11:04 AM
Programming and Parameters
3-5
Display Group (continued)
d012 [Control Source]
Related Parameter(s): P036, P038, A051-A054
Displays the active source of the Start Command and Speed Command which are normally defined
by the settings of P036 [Start Source] and P038 [Speed Reference] but may be overridden by digital
inputs. Refer to the flowcharts on pages 1-23 and 1-24 for details.
Start Command
Digit 0
0 = Keypad
1 = 3-Wire
2 = 2-Wire
3 = 2-Wire Level Sensitive
4 = 2-Wire High Speed
5 = RS485 (DSI) Port
9 = Jog
Speed Command
Digit 1
0 = Drive Potentiometer
1 = A069 [Internal Freq]
2 = 0-10V Input/Remote Potentiometer
3 = 4-20mA Input
4 = A070-A077 [Preset Freq x]
(A051 - A053 [Digital Inx Sel] must be set to 4)
5 = RS485 (DSI) Port
6 = StepLogic Control (Parameters A140 - A147)
7 = Anlg In Mult
8 = PID
9 = Jog Freq
Reserved
Digit 2
Reserved
Digit 3
Values
Default:
Read Only
Min/Max:
0/9
Display:
1
d013 [Contrl In Status]
Related Parameter(s): d002, P034, P035
Status of the control terminal block control inputs.
Important: Actual control commands may come from a source other than the control terminal block.
1 = Input Present, 0 = Input Not Present
Start / Run FWD Input (I/O Terminal 02)
Bit 0
Direction / Run REV Input (I/O Terminal 03)
Bit 1
Bit 2
Stop Input(1) (I/O Terminal 01)
Dynamic Brake Transistor On
Bit 3
(1)
The stop input must be present in order to start the drive.
When this bit is a 1 the drive can be started.
When this bit is a 0 the drive will stop.
Values
Default:
Read Only
Min/Max:
0/1
Display:
1
PowerFlex 40 Adjustable Frequency AC Drive FRN 1.xx - 6.xx User Manual
Publication 22B-UM001H-EN-E
22B-UM001.book Page 6 Wednesday, January 22, 2014 11:04 AM
3-6
Programming and Parameters
Display Group (continued)
d014 [Dig In Status]
Related Parameter(s): A051-A054
Status of the control terminal block digital inputs.
1 = Input Present, 0 = Input Not Present
Digital In1 Sel (I/O Terminal 05)
Bit 0
Digital In2 Sel (I/O Terminal 06)
Bit 1
Digital In3 Sel (I/O Terminal 07)
Bit 2
Digital In4 Sel (I/O Terminal 08)
Bit 3
Values
Default:
Read Only
Min/Max:
0/1
Display:
1
d015 [Comm Status]
Related Parameter(s): A103-A107
Status of the communications ports.
1 = Condition True, 0 = Condition False
Receiving Data
Bit 0
Transmitting Data
Bit 1
RS485 (DSI) Based Option Connected
Bit 2
(Allen-Bradley devices only.)
Communication Error Occurred
Bit 3
Values
Default:
Read Only
Min/Max:
0/1
Display:
1
d016 [Control SW Ver]
Main Control Board software version.
Values
Default:
Read Only
Min/Max:
1.00/99.99
Display:
0.01
d017 [Drive Type]
Used by Rockwell Automation field service personnel.
Values
Default:
Read Only
Min/Max:
1001/9999
Display:
1
PowerFlex 40 Adjustable Frequency AC Drive FRN 1.xx - 6.xx User Manual
Publication 22B-UM001H-EN-E
22B-UM001.book Page 7 Wednesday, January 22, 2014 11:04 AM
Programming and Parameters
3-7
Display Group (continued)
d018 [Elapsed Run Time]
Accumulated time drive is outputting power. Time is displayed in 10 hour increments.
Values
Default:
Read Only
Min/Max:
0/9999 Hrs
Display:
1 = 10 Hrs
d019 [Testpoint Data]
Related Parameter(s): A102
The present value of the function selected in A102 [Testpoint Sel].
Values
Default:
Read Only
Min/Max:
0/FFFF
Display:
1 Hex
d020 [Analog In 0-10V]
Related Parameter(s): A110, A111
The present value of the voltage at I/O Terminal 13 (100.0% = 10 volts).
Values
Default:
Read Only
Min/Max:
0.0/100.0%
Display:
0.1%
d021 [Analog In 4-20mA]
Related Parameter(s): A112, A113
The present value of the current at I/O Terminal 15 (0.0% = 4mA, 100.0% = 20mA).
Values
Default:
Read Only
Min/Max:
0.0/100.0%
Display:
0.1%
d022 [Output Power]
Output power present at T1, T2 & T3 (U, V & W).
Values
Default:
Read Only
Min/Max:
0.00/(Drive Rated Power × 2)
Display:
0.01 kW
d023 [Output Powr Fctr]
The angle in electrical degrees between motor voltage and motor current.
Values
Default:
Read Only
Min/Max:
0.0/180.0 deg
Display:
0.1 deg
PowerFlex 40 Adjustable Frequency AC Drive FRN 1.xx - 6.xx User Manual
Publication 22B-UM001H-EN-E
22B-UM001.book Page 8 Wednesday, January 22, 2014 11:04 AM
3-8
Programming and Parameters
Display Group (continued)
d024 [Drive Temp]
Present operating temperature of the drive power section.
Values
Default:
Read Only
Min/Max:
0/120 degC
Display:
1 degC
d025 [Counter Status]
The current value of the counter when counter is enabled.
Values
Default:
Read only
Min/Max:
0/9999
Display:
1
d026 [Timer Status]
32
32 bit parameter.
The current value of the timer when timer is enabled.
Values
Default:
Read Only
Min/Max:
0.0/9999 Secs
Display:
0.1 Secs
d028 [Stp Logic Status]
When P038 [Speed Reference] is set to 6 “Stp Logic”, this parameter will display the current step of
the StepLogic profile as defined by parameters A140-A147 [Stp Logic x].
Values
Default:
Read Only
Min/Max:
0/7
Display:
1
d029 [Torque Current]
The current value of the motor torque current.
Values
Default:
Read Only
Min/Max:
0.00/(Drive Rated Amps × 2)
Display:
0.01 Amps
PowerFlex 40 Adjustable Frequency AC Drive FRN 1.xx - 6.xx User Manual
Publication 22B-UM001H-EN-E
22B-UM001.book Page 9 Wednesday, January 22, 2014 11:04 AM
Programming and Parameters
3-9
Basic Program Group
P031 [Motor NP Volts]
Related Parameter(s): d004, A084, A085, A086, A087
Stop drive before changing this parameter.
Set to the motor nameplate rated volts.
Values
Default:
Based on Drive Rating
Min/Max:
20/Drive Rated Volts
Display:
1 VAC
P032 [Motor NP Hertz]
Related Parameter(s): A084, A085, A086, A087, A090
Stop drive before changing this parameter.
Set to the motor nameplate rated frequency.
Values
Default:
60 Hz
Min/Max:
15/400 Hz
Display:
1 Hz
P033 [Motor OL Current]
Related Parameter(s): A055, A058, A061, A089, A090,
A098, A114, A118
Set to the maximum allowable motor current.
The drive will fault on an F7 Motor Overload if the value of this parameter is exceeded by 150% for 60
seconds.
Values
Default:
Based on Drive Rating
Min/Max:
0.0/(Drive Rated Amps × 2)
Display:
0.1 Amps
P034 [Minimum Freq]
Related Parameter(s): d001, d002, d013, P035, A085,
A086, A087, A110, A112
Sets the lowest frequency the drive will output continuously.
Values
Default:
0.0 Hz
Min/Max:
0.0/400.0 Hz
Display:
0.1 Hz
P035 [Maximum Freq]
Related Parameter(s): d001, d002, d013, P034, A065,
A078, A085, A086, A087, A111, A113
Stop drive before changing this parameter.
Sets the highest frequency the drive will output.
Values
Default:
60 Hz
Min/Max:
0/400 Hz
Display:
1 Hz
PowerFlex 40 Adjustable Frequency AC Drive FRN 1.xx - 6.xx User Manual
Publication 22B-UM001H-EN-E
22B-UM001.book Page 10 Wednesday, January 22, 2014 11:04 AM
3-10
Programming and Parameters
Basic Program Group (continued)
P036 [Start Source]
Related Parameter(s): d012, P037
Stop drive before changing this parameter.
Sets the control scheme used to start the drive.
Refer to Start and Speed Reference Control on page 1-23 for details about how other drive settings
can override the setting of this parameter.
Important: For all settings except option 3, the drive must receive a leading edge from the start input
for the drive to start after a stop input, loss of power or fault condition.
Options 0 “Keypad” (Default)
• Integral keypad controls drive operation.
• I/O Terminal 1 “Stop” = coast to stop.
• When active, the Reverse key is also active unless
disabled by A095 [Reverse Disable].
1 “3-Wire”
I/O Terminal 1 “Stop” = stop according to the value set in
P037 [Stop Mode].
2 “2-Wire”
I/O Terminal 1 “Stop” = coast to stop.
3 “2-W Lvl Sens”
Drive will restart after a “Stop” command when:
• Stop is removed
and
• Start is held active
!
ATTENTION: Hazard of injury exists due to unintended operation.
When P036 [Start Source] is set to option 3, and the Run input is
maintained, the Run inputs do not need to be toggled after a Stop input for
the drive to run again. A Stop function is provided only when the Stop input
is active (open).
4 “2-W Hi Speed”
Important: There is greater potential voltage on the output
terminals when using this option.
• Outputs are kept in a ready-to-run state. The drive will
respond to a “Start” command within 10 ms.
• I/O Terminal 1 “Stop” = coast to stop.
5 “Comm Port”
• Remote communications. Refer to Appendix C for details.
• I/O Terminal 1 “Stop” = coast to stop.
6 “Momt FWD/REV”
• Drive will start after a momentary input from either the
Run FWD Input (I/O Terminal 02) or the Run REV Input (I/
O Terminal 03).
• I/O Terminal 1 “Stop” = coast to stop.
PowerFlex 40 Adjustable Frequency AC Drive FRN 1.xx - 6.xx User Manual
Publication 22B-UM001H-EN-E
22B-UM001.book Page 11 Wednesday, January 22, 2014 11:04 AM
Programming and Parameters
3-11
Basic Program Group (continued)
P037 [Stop Mode]
Related Parameter(s): P036, A080, A081, A082, A105, A160
Active stop mode for all stop sources [e.g. keypad, run forward (I/O Terminal 02), run reverse (I/O
Terminal 03), RS485 port] except as noted below.
Important: I/O Terminal 01 is always a coast to stop input except when P036 [Start Source] is set for
“3-Wire” control. When in three wire control, I/O Terminal 01 is controlled by P037 [Stop Mode].
Hardware Enable Circuitry
By default, I/O Terminal 01 is a coast to stop input. The status of the input is interpreted by drive
software. If the application requires the drive to be disabled without software interpretation, a “dedicated” hardware enable configuration can be utilized. This is accomplished by removing the ENBL
enable jumper on the control board. In this case, the drive will always coast to a stop regardless of the
settings of P036 [Start Source] and P037 [Stop Mode].
Options 0 “Ramp, CF”(1) (Default) Ramp to Stop. “Stop” command clears active fault.
1 “Coast, CF”(1)
Coast to Stop. “Stop” command clears active fault.
2 “DC Brake, CF”(1)
DC Injection Braking Stop. “Stop” command clears active
fault.
3 “DCBrkAuto,CF”(1)
DC Injection Braking Stop with Auto Shutoff.
• Standard DC Injection Braking for value set in A080 [DC
Brake Time].
OR
• Drive shuts off if the drive detects that the motor is
stopped.
“Stop” command clears active fault.
4 “Ramp”
Ramp to Stop.
5 “Coast”
Coast to Stop.
6 “DC Brake”
DC Injection Braking Stop.
7 “DC BrakeAuto”
DC Injection Braking Stop with Auto Shutoff.
• Standard DC Injection Braking for value set in A080 [DC
Brake Time].
OR
• Drive shuts off if current limit is exceeded.
(1)
8 “Ramp+EM B,CF”
Ramp to Stop with EM Brake Control. “Stop” Command
clears active fault.
9 “Ramp+EM Brk”
Ramp to Stop with EM Brake Control.
Stop input also clears active fault.
PowerFlex 40 Adjustable Frequency AC Drive FRN 1.xx - 6.xx User Manual
Publication 22B-UM001H-EN-E
22B-UM001.book Page 12 Wednesday, January 22, 2014 11:04 AM
3-12
Programming and Parameters
Basic Program Group (continued)
P038 [Speed Reference] Related Parameter(s): d001, d002, d012, d020, d021, P039, P040,
A051-A054, A069, A070-A077, A110-A113, A123, A132, A140-A147, A150-A157
Sets the source of the speed reference to the drive.
The drive speed command can be obtained from a number of different sources. The source is
normally determined by P038 [Speed Reference]. However, when A051 - A054 [Digital Inx Sel] is set
to option 2, 4, 5, 6, 11, 12, 13, 14, 15 and the digital input is active, or if A132 [PID Ref Sel] is not set
to option 0, the speed reference commanded by P038 [Speed Reference] will be overridden. Refer to
the flowchart on page 1-23 for more information on speed reference control priority.
Options 0 “Drive Pot” (Default)
Frequency command from the potentiometer on the integral
keypad.
Important: This option is not available with IP66, NEMA/UL
Type 4X rated drives. Internal frequency command comes
from A069 [Internal Freq].
1 “InternalFreq”
(IP66, NEMA/UL Type
4X Default)
Internal frequency command from A069 [Internal Freq]. Must
be set when using MOP function.
2 “0-10V Input”
External frequency command from the 0-10V or ±10V analog
input or remote potentiometer.
3 “4-20mA Input”
External frequency command from the 4-20mA analog input.
4 “Preset Freq”
External frequency command as defined by A070 - A077
[Preset Freq x] when A051 - A054 [Digital Inx Sel] are
programmed as “Preset Frequencies” and the digital inputs
are active.
5 “Comm Port”
External frequency command from the communications port.
Refer to Appendix C for details.
6 “Stp Logic”
External frequency command as defined by A070 - A077
[Preset Freq x] and A140 - A147 [Stp Logic x].
7 “Anlg In Mult”
External frequency command as defined by the product of the
analog inputs (shown in d020 [Analog In 0-10V] and d021
[Analog In 4-20mA]).
[Analog In 0-10V] × [Analog In 4-20mA] = Speed Command
Example: 100% × 50% = 50%
P039 [Accel Time 1]
Related Parameter(s): P038, P040, A051-A054,
A067, A070-A077, A140-A147
Sets the rate of acceleration for all speed increases.
Maximum Freq
= Accel Rate
Accel Time
Values
Default:
10.0 Secs
Min/Max:
0.0/600.0 Secs
Display:
0.1 Secs
P035 [Maximum Freq]
0
0
P039 or A067
[Accel Time x]
n
Ac
c
ele
o
ati
ler
rat
i
on
ce
De
Speed
Time
P040 or A068
[Decel Time x]
PowerFlex 40 Adjustable Frequency AC Drive FRN 1.xx - 6.xx User Manual
Publication 22B-UM001H-EN-E
22B-UM001.book Page 13 Wednesday, January 22, 2014 11:04 AM
Programming and Parameters
3-13
Basic Program Group (continued)
P040 [Decel Time 1]
Related Parameter(s): P038, P039, A051-A054,
A068, A070-A077, A140-A147
Sets the rate of deceleration for all speed decreases.
Maximum Freq
= Decel Rate
Decel Time
Values
Default:
10.0 Secs
Min/Max:
0.1/600.0 Secs
Display:
0.1 Secs
P035 [Maximum Freq]
Ac
on
ce
ati
ler
ler
ati
ce
on
De
Speed
0
0
P039 or A067
[Accel Time x]
Time
P040 or A068
[Decel Time x]
P041 [Reset To Defalts]
Stop drive before changing this parameter.
Resets all parameter values to factory defaults.
Options 0 “Ready/Idle” (Default)
• After the reset function is complete, this parameter will set
itself back to “0”.
• Causes an F48 Params Defaulted fault.
1 “Factory Rset”
P042 [Voltage Class]
Stop drive before changing this parameter.
Sets the voltage class of 600V drives.
Options 2 “Low Voltage”
480V
3 “High Voltage”
(Default)
600V
P043 [Motor OL Ret]
Related Parameter(s): P033
Enables/disables the Motor Overload Retention function. When Enabled, the value held in the motor
overload counter is saved at power-down and restored at power-up. A change to this parameter
setting resets the counter.
Options 0 “Disabled” (Default)
1 “Enabled”
PowerFlex 40 Adjustable Frequency AC Drive FRN 1.xx - 6.xx User Manual
Publication 22B-UM001H-EN-E
22B-UM001.book Page 14 Wednesday, January 22, 2014 11:04 AM
3-14
Programming and Parameters
Advanced Program Group
A051 [Digital In1 Sel]
(I/O Terminal 05)
Related Parameter(s): d012, d014, P038, P039, P040,
A067, A068, A070-A077, A078, A079, A118, A140-A147
A052 [Digital In2 Sel]
(I/O Terminal 06)
A053 [Digital In3 Sel]
Stop drive before changing this parameter.
(I/O Terminal 07)
A054 [Digital In4 Sel]
(I/O Terminal 08)
Selects the function for the digital inputs. Refer to the flowchart on page 1-23 for more information on
speed reference control priority.
Options 0 “Not Used”
Terminal has no function but can be read over network
communications via d014 [Dig In Status].
• When active, A067 [Accel Time 2] and A068 [Decel Time
2] are used for all ramp rates except Jog.
• Can only be tied to one input.
Refer to the flowchart on page 1-24 for more information on
Accel/Decel selection.
2 “Jog”
• When input is present, drive accelerates according to the
value set in A079 [Jog Accel/Decel] and ramps to the
value set in A078 [Jog Frequency].
• When input is removed, drive ramps to a stop according to
the value set in A079 [Jog Accel/Decel].
• A valid “Start” command will override this input.
3 “Aux Fault”
When enabled, an F2 Auxiliary Input fault will occur when the
input is removed.
4 “Preset Freq”
Refer to A070 - A077 [Preset Freq x].
(A051 & A052 Default) Important: Digital Inputs have priority for frequency control
when programmed as Preset Speed and are active. Refer to
the flowchart on page 1-23 for more information on speed
reference control priority.
5 “Local”
When active, sets integral keypad as start source and
(A053 Default)
potentiometer on the integral keypad as speed source.
Important: Speed source for IP66, NEMA/UL Type 4X rated
drives comes from A069 [Internal Freq].
6 “Comm Port”
• When active, sets communications device as default start/
speed command source.
• Can only be tied to one input.
7 “Clear Fault”
When active, clears an active fault.
8 “RampStop,CF”
Causes drive to immediately ramp to a stop regardless of how
P037 [Stop Mode] is set.
9 “CoastStop,CF”
Causes drive to immediately coast to a stop regardless of
how P037 [Stop Mode] is set.
10 “DCInjStop,CF”
Causes drive to immediately begin a DC Injection stop
regardless of how P037 [Stop Mode] is set.
11 “Jog Forward”
Drive accelerates to A078 [Jog Frequency] according to A079
(A054 Default)
[Jog Accel/Decel] and ramps to stop when input becomes
inactive. A valid start will override this command.
12 “Jog Reverse”
Drive accelerates to A078 [Jog Frequency] according to A079
[Jog Accel/Decel] and ramps to stop when input becomes
inactive. A valid start will override this command.
1 “Acc & Dec 2”
PowerFlex 40 Adjustable Frequency AC Drive FRN 1.xx - 6.xx User Manual
Publication 22B-UM001H-EN-E
22B-UM001.book Page 15 Wednesday, January 22, 2014 11:04 AM
Programming and Parameters
A051 13 “10V In Ctrl”
A054
Options 14 “20mA In Ctrl”
(Cont.)
15 “PID Disable”
16 “MOP Up”
17 “MOP Down”
18 “Timer Start”
19 “Counter In”
20
21
22
23
“Reset Timer”
“Reset Countr”
“Rset Tim&Cnt”
“Logic In1”
24 “Logic In2”
25 “Current Lmt2”
26 “Anlg Invert”
27 “EM Brk Rlse”
!
3-15
Selects 0-10V or ±10V control as the frequency reference.
Start source is not changed.
Selects 4-20mA control as the frequency reference. Start
source is not changed.
Disables PID function. Drive uses the next valid non-PID
speed reference.
Increases the value of A069 [Internal Freq] at the current
Accel rate if P038 [Speed Reference] is set to 1
“InternalFreq”.
For IP20 rated drives, the default for A069 is 60.0 Hz.
For IP66, NEMA/UL Type 4X drives, the default for A069 is
0.0 Hz.
Decreases the value of A069 [Internal Freq] at the current
Decel rate if P038 [Speed Reference] is set to 1
“InternalFreq”.
For IP20 rated drives, the default for A069 is 60.0 Hz.
For IP66, NEMA/UL Type 4X drives, the default for A069 is
0.0 Hz.
Clears and starts the timer function. May be used to control
the relay or opto outputs.
Starts the counter function. May be used to control the relay
or opto outputs.
Clears the active timer.
Clears the active counter.
Clears the active timer and counter.
Logic function input number 1. May be used to control the
relay or opto outputs (see parameters A055, A058, A061
Options 11-14). May be used in conjunction with StepLogic
parameters A140 - A147 [Stp Logic x].
Logic function input number 2. May be used to control the
relay or opto outputs (see parameters A055, A058, A061
Options 11-14). May be used in conjunction with StepLogic
parameters A140 - A147 [Stp Logic x].
When active, A118 [Current Limit 2] determines the drive
current limit level.
Inverts the scaling of the analog input levels set in
A110 [Anlg In 0-10V Lo] and A111 [Anlg In 0-10V Hi] or
A112 [Anlg In4-20mA Lo] and A113 [Anlg In4-20mA Hi].
If EM brake function is enabled, this input releases the brake.
ATTENTION: If a hazard of injury due to movement of equipment or
material exists, an auxiliary mechanical braking device must be used.
PowerFlex 40 Adjustable Frequency AC Drive FRN 1.xx - 6.xx User Manual
Publication 22B-UM001H-EN-E
22B-UM001.book Page 16 Wednesday, January 22, 2014 11:04 AM
3-16
Programming and Parameters
Advanced Program Group (continued)
A055 [Relay Out Sel]
Related Parameter(s): P033, A056, A092, A140-A147, A150-A157,
A160, A161
Sets the condition that changes the state of the output relay contacts.
Options 0 “Ready/Fault”
Relay changes state when power is applied. This indicates
that the drive is ready for operation. Relay returns drive to
(Default)
shelf state when power is removed or a fault occurs.
1 “At Frequency”
Drive reaches commanded frequency.
2 “MotorRunning”
Motor is receiving power from the drive.
3 “Reverse”
Drive is commanded to run in reverse direction.
4 “Motor Overld”
Motor overload condition exists.
5 “Ramp Reg”
Ramp regulator is modifying the programmed accel/decel
times to avoid an overcurrent or overvoltage fault from
occurring.
6 “Above Freq”
• Drive exceeds the frequency (Hz) value set in A056 [Relay
Out Level].
• Use A056 to set threshold.
• Drive exceeds the current (% Amps) value set in A056
[Relay Out Level].
• Use A056 to set threshold.
7 “Above Cur”
8 “Above DCVolt”
9 “Retries Exst”
10 “Above Anlg V”
11 “Logic In 1”
Important: Value for A056 [Relay Out Level] must be entered
in percent of drive rated output current.
• Drive exceeds the DC bus voltage value set in A056
[Relay Out Level].
• Use A056 to set threshold.
Value set in A092 [Auto Rstrt Tries] is exceeded.
• Analog input voltage (I/O Terminal 13) exceeds the value
set in A056 [Relay Out Level].
• Do not use if A123 [10V Bipolar Enbl] is set to 1 “Bi-Polar In”.
• This parameter setting can also be used to indicate a PTC
trip point when the input (I/O Terminal 13) is wired to a
PTC and external resistor.
• Use A056 to set threshold.
An input is programmed as “Logic In 1” and is active.
12 “Logic In 2”
An input is programmed as “Logic In 2” and is active.
13 “Logic 1 & 2”
Both Logic inputs are programmed and active.
14 “Logic 1 or 2”
One or both Logic inputs are programmed and one or both is
active.
15 “StpLogic Out”
Drive enters StepLogic step with Digit 3 of Command Word
(A140 - A147) set to enable StepLogic output.
16 “Timer Out”
•
•
•
•
•
17 “Counter Out”
18 “Above PF Ang”
Timer has reached value set in A056 [Relay Out Level].
Use A056 to set threshold.
Counter has reached value set in A056 [Relay Out Level].
Use A056 to set threshold.
Power Factor angle has exceeded the value set in A056
[Relay Out Level].
• Use A056 to set threshold.
PowerFlex 40 Adjustable Frequency AC Drive FRN 1.xx - 6.xx User Manual
Publication 22B-UM001H-EN-E
22B-UM001.book Page 17 Wednesday, January 22, 2014 11:04 AM
Programming and Parameters
A055
19 “Anlg In Loss”
Options
(Cont.)
20 “ParamControl”
3-17
Analog input loss has occurred. Program A122 [Analog In
Loss] for desired action when input loss occurs.
Prior to FRN 4.01, this option enables the output to be
controlled over network communications by writing to A056
[Relay Out Level]. (0 = Off, 1 = On.)
With FRN 4.01 and later, the logic command word bit 15 has
full control of A056. See Writing (06) Logic Command
Data on page C-4.
21 “NonRec Fault”
22 “EM Brk Cntrl”
• Value set in A092 [Auto Rstrt Tries] is exceeded.
• A092 [Auto Rstrt Tries] in not enabled.
• A Non-resettable fault has occurred.
EM brake is energized. Program A160 [EM Brk Off Delay] and
A161 [EM Brk On Delay] for desired action.
23 “Above Fcmd”
The current commanded frequency exceeds the value set in
A056 [Relay Out Level].
24 “MsgControl”
With FRN 4.01 and later, this option enables the output to be
controlled over network communications by writing to A056
[Relay Out Level]. (0 = Off, 1 = On.)
A056 [Relay Out Level]
32
Related Parameter(s): A055
32 bit parameter.
Sets the trip point for the digital output relay if the value of A055 [Relay Out Sel] is 6, 7, 8, 10, 16, 17,
18 or 20.
With FRN 4.01 and later, when the value of A055 is set to 20, the logic command word bit 15 has full
control of A056.
A055 Setting
6
7
8
10
16
17
18
20
23
Values
Default:
A056 Min/Max
0/400 Hz
0/180%
0/815 Volts
0/100%
0.1/9999 Secs
1/9999 Counts
1/180 degs
0/1
0/400 Hz
0.0
Min/Max:
0.0/9999
Display:
0.1
PowerFlex 40 Adjustable Frequency AC Drive FRN 1.xx - 6.xx User Manual
Publication 22B-UM001H-EN-E
22B-UM001.book Page 18 Wednesday, January 22, 2014 11:04 AM
3-18
Programming and Parameters
Advanced Program Group (continued)
A058 [Opto Out1 Sel]
A061 [Opto Out2 Sel]
Related Parameter(s): P033, A059, A062, A092, A122, A123,
A160, A161, A140-A147, A150-A157
Determines the operation of the programmable opto outputs.
Options 0 “Ready/Fault”
Opto outputs are active when power is applied. This indicates
that the drive is ready for operation. Opto outputs are inactive
when power is removed or a fault occurs.
1 “At Frequency”
(A061 Default)
2 “MotorRunning”
(A058 Default)
3 “Reverse”
Drive reaches commanded frequency.
Motor is receiving power from the drive.
Drive is commanded to run in reverse direction.
4 “Motor Overld”
Motor overload condition exists.
5 “Ramp Reg”
Ramp regulator is modifying the programmed accel/decel
times to avoid an overcurrent or overvoltage fault from
occurring.
6 “Above Freq”
• Drive exceeds the frequency (Hz) value set in A059 or
A062 [Opto Outx Level].
• Use A059 or A062 to set threshold.
• Drive exceeds the current (% Amps) value set in A059 or
A062 [Opto Outx Level].
• Use A059 or A062 to set threshold.
7 “Above Cur”
8 “Above DCVolt”
9 “Retries Exst”
10 “Above Anlg V”
11 “Logic In 1”
Important: Value for A059 or A062 [Opto Outx Level] must be
entered in percent of drive rated output current.
• Drive exceeds the DC bus voltage value set in A059 or
A062 [Opto Outx Level].
• Use A059 or A062 to set threshold.
Value set in A092 [Auto Rstrt Tries] is exceeded.
• Analog input voltage (I/O Terminal 13) exceeds the value
set in A059 or A062 [Opto Outx Level].
• Do not use if A123 [10V Bipolar Enbl] is set to 1 “Bi-Polar
In”.
• This parameter setting can also be used to indicate a PTC
trip point when the input (I/O Terminal 13) is wired to a
PTC and external resistor.
• Use A059 or A062 to set threshold.
An input is programmed as “Logic In 1” and is active.
12 “Logic In 2”
An input is programmed as “Logic In 2” and is active.
13 “Logic 1 & 2”
Both Logic inputs are programmed and active.
14 “Logic 1 or 2”
One or both Logic inputs are programmed and one or both is
active.
15 “StpLogic Out”
Drive enters StepLogic step with Digit 3 of Command Word
(A140 - A147) set to enable StepLogic output.
16 “Timer Out”
• Timer has reached value set in A059 or A062 [Opto Outx
Level].
• Use A059 or A062 to set threshold.
• Counter has reached value set in A059 or A062 [Opto
Outx Level].
• Use A059 or A062 to set threshold.
17 “Counter Out”
PowerFlex 40 Adjustable Frequency AC Drive FRN 1.xx - 6.xx User Manual
Publication 22B-UM001H-EN-E
22B-UM001.book Page 19 Wednesday, January 22, 2014 11:04 AM
Programming and Parameters
3-19
A058,
18 “Above PF Ang”
A061
Options
(Cont.)
19 “Anlg In Loss”
• Power Factor angle has exceeded the value set in A059 or
A062 [Opto Outx Level].
• Use A059 or A062 to set threshold.
Analog input loss has occurred. Program A122 [Analog In
Loss] for desired action when input loss occurs.
20 “ParamControl”
Prior to FRN 4.01, this option enables the output to be
controlled over network communications by writing to A059 or
A062 [Opto Outx Level]. (0 = Off, 1 = On.)
With FRN 4.01 and later:
Setting this option for A058 means the logic command word
bit 6 has full control of A059.
Setting this option for A059 means the logic command word
bit 7 has full control of A062.
See Writing (06) Logic Command Data on page C-4.
21 “NonRec Fault”
22 “EM Brk Cntrl”
• Value set in A092 [Auto Rstrt Tries] is exceeded.
• A092 [Auto Rstrt Tries] in not enabled.
• A Non-resettable fault has occurred.
EM brake is energized. Program A160 [EM Brk Off Delay] and
A161 [EM Brk On Delay] for desired action.
23 “Above Fcmd”
The current commanded frequency exceeds the value set in
A059 or A062 [Opto Outx Level].
24 “MsgControl”
With FRN 4.01 and later:
Enables the output to be controlled over the network
communications by writing to A059 or A062 [Opto Outx
Level]. (0 = Off, 1 = On.)
A059 [Opto Out1 Level]
A062 [Opto Out2 Level]
32
Related Parameter(s): A058, A061
32 bit parameter.
Determines the on/off point for the opto outputs when A058 or A061 [Opto Outx Sel] is set to option 6,
7, 8, 10, 16, 17, 18 or 20.
With FRN 4.01 and later, when the value of A058 is set to 20, the logic command word bit 6 has full
control of A059 and when the value of A061 is set to 20, bit 7 has full control of A062.
A058 & A061 Setting
6
7
8
10
16
17
18
20
23
Values
Default:
A059 & A062 Min/Max
0/400 Hz
0/180%
0/815 Volts
0/100%
0.1/9999 Secs
1/9999 Counts
1/180 degs
0/1
0/400 Hz
0.0
Min/Max:
0.0/9999
Display:
0.1
PowerFlex 40 Adjustable Frequency AC Drive FRN 1.xx - 6.xx User Manual
Publication 22B-UM001H-EN-E
22B-UM001.book Page 20 Wednesday, January 22, 2014 11:04 AM
3-20
Programming and Parameters
Advanced Program Group (continued)
A064 [Opto Out Logic]
Determines the logic (Normally Open/NO or Normally Closed/NC) of the opto outputs.
A064 Option
0
1
2
3
Values
Opto Out1 Logic
NO (Normally Open)
NC (Normally Closed)
NO (Normally Open)
NC (Normally Closed)
Opto Out2 Logic
NO (Normally Open)
NO (Normally Open)
NC (Normally Closed)
NC (Normally Closed)
Default:
0
Min/Max:
0/3
Display:
1
A065 [Analog Out Sel]
Related Parameter(s): P035, A066
Sets the analog output signal mode (0-10V, 0-20mA, or 4-20mA). The output is used to provide a
signal that is proportional to several drive conditions.
Option
0 “OutFreq 0-10”
1 “OutCurr 0-10”
2 “OutVolt 0-10”
3 “OutPowr 0-10”
4 “TstData 0-10”
5 “OutFreq 0-20”
6 “OutCurr 0-20”
7 “OutVolt 0-20”
8 “OutPowr 0-20”
9 “TstData 0-20”
10 “OutFreq 4-20”
11 “OutCurr 4-20”
12 “OutVolt 4-20”
13 “OutPowr 4-20”
14 “TstData 4-20”
15 “OutTorq 0-10”
16 “OutTorq 0-20”
17 “OutTorq 4-20”
18 “Setpnt 0-10”
19 “Setpnt 0-20”
20 “Setpnt 4-20”
21 “MinFreq 0-10”
22 “MinFreq 0-20”
23 “MinFreq 4-20”
Values
Output
Range
0-10V
0-10V
0-10V
0-10V
0-10V
0-20mA
0-20mA
0-20mA
0-20mA
0-20mA
4-20mA
4-20mA
4-20mA
4-20mA
4-20mA
0-10V
0-20 mA
4-20 mA
0-10V
0-20 mA
4-20 mA
0-10V
0-20 mA
4-20 mA
Default:
Minimum Output
Value
0V = 0 Hz
0V = 0 Amps
0V = 0 Volts
0V = 0 kW
0V = 0000
0 mA = 0 Hz
0 mA = 0 Amps
0 mA = 0 Volts
0 mA = 0 kW
0 mA = 0000
4 mA = 0 Hz
4 mA = 0 Amps
4 mA = 0 Volts
4 mA = 0 kW
4 mA = 0000
0V = 0 Amps
0 mA = 0 Amps
4 mA = 0 Amps
0V = 0%
0 mA = 0%
4 mA = 0%
0V = Min. Freq
0 mA = Min. Freq
4 mA = Min. Freq
Maximum Output Value
A066 [Analog Out High]
P035 [Maximum Freq]
200% Drive Rated Output Current
120% Drive Rated Output Volts
200% Drive Rated Power
65535 (Hex FFFF)
P035 [Maximum Freq]
200% Drive Rated Output Current
120% Drive Rated Output Volts
200% Drive Rated Power
65535 (Hex FFFF)
P035 [Maximum Freq]
200% Drive Rated Output Current
120% Drive Rated Output Volts
200% Drive Rated Power
65535 (Hex FFFF)
200% Drive Rated FLA
200% Drive Rated FLA
200% Drive Rated FLA
100.0% Setpoint Setting
100.0% Setpoint Setting
100.0% Setpoint Setting
P035 [Maximum Freq]
P035 [Maximum Freq]
P035 [Maximum Freq]
0
Min/Max:
0/23
Display:
1
PowerFlex 40 Adjustable Frequency AC Drive FRN 1.xx - 6.xx User Manual
Publication 22B-UM001H-EN-E
DIP Switch
Position
0-10V
0-10V
0-10V
0-10V
0-10V
0-20mA
0-20mA
0-20mA
0-20mA
0-20mA
0-20mA
0-20mA
0-20mA
0-20mA
0-20mA
0-10V
0-20 mA
0-20 mA
0-10V
0-20 mA
0-20 mA
0-10V
0-20 mA
0-20 mA
Related
Parameter
d001
d003
d004
d022
d019
d001
d003
d004
d022
d019
d001
d003
d004
d022
d019
d029
d029
d029
A109
A109
A109
d001
d001
d001
22B-UM001.book Page 21 Wednesday, January 22, 2014 11:04 AM
Programming and Parameters
3-21
Advanced Program Group (continued)
A066 [Analog Out High]
Related Parameter(s): A065
Scales the Maximum Output Value for the A065 [Analog Out Sel] source setting.
Examples:
A066 Setting
50%
90%
Values
A065 Setting
1 “OutCurr 0-10”
8 “OutPowr 0-20”
A065 Max. Output Value
5V for 200% Drive Rated Output Current
18mA for 200% Drive Rated Power
Default:
100%
Min/Max:
0/800%
Display:
1%
A067 [Accel Time 2]
Related Parameter(s): P039, A051-A054, A070-A077, A140-A147
When active, sets the rate of acceleration for all speed increases except jog. Refer to the flowchart on
page 1-24 for details.
Maximum Freq
= Accel Rate
Accel Time
Values
Default:
20.0 Secs
Min/Max:
0.0/600.0 Secs
Display:
0.1 Secs
P035 [Maximum Freq]
Ac
on
ce
ati
ler
ler
ati
ce
on
De
Speed
0
0
P039 or A067
[Accel Time x]
Time
P040 or A068
[Decel Time x]
PowerFlex 40 Adjustable Frequency AC Drive FRN 1.xx - 6.xx User Manual
Publication 22B-UM001H-EN-E
22B-UM001.book Page 22 Wednesday, January 22, 2014 11:04 AM
3-22
Programming and Parameters
Advanced Program Group (continued)
A068 [Decel Time 2]
Related Parameter(s): P040, A051-A054, A070-A077, A140-A147
When active, sets the rate of deceleration for all speed decreases except jog. Refer to the flowchart
on page 1-24 for details.
Maximum Freq
= Decel Rate
Decel Time
Values
Default:
20.0 Secs
Min/Max:
0.1/600.0 Secs
Display:
0.1 Secs
P035 [Maximum Freq]
Ac
on
ce
ati
ler
ler
ati
ce
on
De
Speed
0
0
P039 or A067
[Accel Time x]
Time
P040 or A068
[Decel Time x]
A069 [Internal Freq]
Related Parameter(s): P038, A162
Provides the frequency command to the drive when P038 [Speed Reference] is set to 1 “Internal
Freq”. When enabled, this parameter will change the frequency command in “real time” using the
integral keypad Up Arrow or Down Arrow when in program mode.
Important: Once the desired command frequency is reached, the Enter key must be pressed to store
this value to EEPROM memory. If the ESC key is used before the Enter key, the frequency will return
to the original value following the normal accel/decel curve.
If A051 - A054 [Digital Inx Sel] is set to 16 “MOP Up” or 17 “MOP Down” this parameter acts as the
MOP frequency reference.
Values
Default:
60.0 Hz for IP20 rated drives
0.0 Hz for IP66, NEMA/UL Type 4X drives
Min/Max:
0.0/400.0 Hz
Display:
0.1 Hz
PowerFlex 40 Adjustable Frequency AC Drive FRN 1.xx - 6.xx User Manual
Publication 22B-UM001H-EN-E
22B-UM001.book Page 23 Wednesday, January 22, 2014 11:04 AM
Programming and Parameters
3-23
Advanced Program Group (continued)
A070 [Preset Freq 0](1)
A071 [Preset Freq 1]
A072 [Preset Freq 2]
A073 [Preset Freq 3]
A074 [Preset Freq 4]
A075 [Preset Freq 5]
A076 [Preset Freq 6]
A077 [Preset Freq 7]
A070 Default:(1)
A071 Default:
A072 Default:
A073 Default:
A074 Default:
A075 Default:
A076 Default:
A077 Default:
Values
Related Parameter(s): P038, P039, P040, A051-A053,
A067, A068, A140-A147, A150-A157
0.0 Hz
5.0 Hz
10.0 Hz
20.0 Hz
30.0 Hz
40.0 Hz
50.0 Hz
60.0 Hz
Min/Max:
0.0/400.0 Hz
Display:
0.1 Hz
Provides a fixed frequency command value when A051 - A053 [Digital Inx Sel] is set to 4 “Preset
Frequencies”.
An active preset input will override speed command as shown in the flowchart on page 1-23.
(1)
To activate A070 [Preset Freq 0] set P038 [Speed Reference] to option 4 “Preset Freq 0-3”.
Input State
of Digital In 1
(I/O Terminal 05
when A051 = 4)
Input State
of Digital In 2
(I/O Terminal 06
when A052 = 4)
Input State
of Digital In 3
(I/O Terminal 07
when A053 = 4)
Frequency Source
Accel / Decel Parameter Used(2)
0
0
0
A070 [Preset Freq 0]
[Accel Time 1] / [Decel Time 1]
1
0
0
A071 [Preset Freq 1]
[Accel Time 1] / [Decel Time 1]
0
1
0
A072 [Preset Freq 2]
[Accel Time 2] / [Decel Time 2]
1
1
0
A073 [Preset Freq 3]
[Accel Time 2] / [Decel Time 2]
0
0
1
A074 [Preset Freq 4]
[Accel Time 1] / [Decel Time 1]
1
0
1
A075 [Preset Freq 5]
[Accel Time 1] / [Decel Time 1]
0
1
1
A076 [Preset Freq 6]
[Accel Time 2] / [Decel Time 2]
1
1
1
A077 [Preset Freq 7]
[Accel Time 2] / [Decel Time 2]
(2)
When a Digital Input is set to “Accel 2 & Decel 2”, and the input is active, that input overrides the settings in this
table.
A078 [Jog Frequency]
Related Parameter(s): P035, A051-A054, A079
Sets the output frequency when a jog command is issued.
Values
Default:
10.0 Hz
Min/Max:
0.0/[Maximum Freq]
Display:
0.1 Hz
PowerFlex 40 Adjustable Frequency AC Drive FRN 1.xx - 6.xx User Manual
Publication 22B-UM001H-EN-E
22B-UM001.book Page 24 Wednesday, January 22, 2014 11:04 AM
3-24
Programming and Parameters
Advanced Program Group (continued)
A079 [Jog Accel/Decel]
Related Parameter(s): A078, A051-A054
Sets the acceleration and deceleration time when a jog command is issued.
Values
Default:
10.0 Secs
Min/Max:
0.1/600.0 Secs
Display:
0.1 Secs
A080 [DC Brake Time]
Related Parameter(s): P037, A081
Sets the length of time that DC brake current is “injected” into the motor. Refer to parameter A081 [DC
Brake Level].
Values
Default:
0.0 Secs
Min/Max:
0.0/99.9 Secs (A setting of 99.9 = Continuous)
Display:
0.1 Secs
A081 [DC Brake Level]
Related Parameter(s): P037, A080
Defines the maximum DC brake current, in amps, applied to the motor when P037 [Stop Mode] is set
to either “Ramp” or “DC Brake”.
Values
Default:
Drive Rated Amps × 0.05
Min/Max:
0.0/(Drive Rated Amps × 1.8)
Display:
0.1 Amps
P037 Ramp-to-Stop Mode
P037 DC Injection Braking Mode
Vo
lta
ge
[DC Brake Time]
Spe
ed
Volts/Speed
Volts/Speed
Voltage
Speed
[DC Brake Time]
[DC Brake Level]
[DC Brake Level]
Time
Time
Stop Command
!
!
Stop Command
ATTENTION: If a hazard of injury due to movement of equipment or material exists,
an auxiliary mechanical braking device must be used.
ATTENTION: This feature should not be used with synchronous or permanent
magnet motors. Motors may be demagnetized during braking.
PowerFlex 40 Adjustable Frequency AC Drive FRN 1.xx - 6.xx User Manual
Publication 22B-UM001H-EN-E
22B-UM001.book Page 25 Wednesday, January 22, 2014 11:04 AM
Programming and Parameters
3-25
Advanced Program Group (continued)
A082 [DB Resistor Sel]
Related Parameter(s): P037
Stop drive before changing this parameter.
Enables/disables external dynamic braking.
Setting
0
1
2
3-99
Min/Max
“Disabled”
“Normal RA Res” (5% Duty Cycle) – Refer to Table B.C on page B-2.
“NoProtection” (100% Duty Cycle)
“x%Duty Cycle” Limited (3% – 99% of Duty Cycle)
The drive is able to provide full braking indefinitely. Braking power is limited by the external DB
resistor. When this parameter is set to 1 “Normal RA Res” and an appropriate resistor is used (see
selection Table B.C), the drive provides calculated resistor overload protection. However, the drive
cannot protect against a brake IGBT failure.
!
Values
ATTENTION: A risk of fire exists if external braking resistors are not protected. The
external resistor package must be self-protected from over temperature or the protective
circuit shown in Figure B.9 on page B-13, or equivalent, must be supplied.
Default:
0
Min/Max:
0/99
Display:
1
A083 [S Curve %]
Sets the percentage of acceleration or deceleration time that is applied to the ramp as S Curve. Time
is added, 1/2 at the beginning and 1/2 at the end of the ramp.
Values
Default:
0% (Disabled)
Min/Max:
0/100%
Display:
1%
Example:
Accel Time = 10 Seconds
S Curve Setting = 50%
S Curve Time = 10 × 0.5 = 5 Seconds
Total Time = 10 + 5 = 15 Seconds
50% S Curve
Target
Target/2
1/2 S Curve Time
2.5 Seconds
Accel Time
10 Seconds
1/2 S Curve Time
2.5 Seconds
Total Time to Accelerate = Accel Time + S Curve Time
PowerFlex 40 Adjustable Frequency AC Drive FRN 1.xx - 6.xx User Manual
Publication 22B-UM001H-EN-E
22B-UM001.book Page 26 Wednesday, January 22, 2014 11:04 AM
3-26
Programming and Parameters
Advanced Program Group (continued)
A084 [Boost Select]
Related Parameter(s): d004, P031, P032, A085,
A086, A087, A125
Sets the boost voltage (% of P031 [Motor NP Volts]) and redefines the Volts per Hz curve.
Active when A125 [Torque Perf Mode] = 0 “V/Hz”.
Drive may add additional voltage unless Option 5 is selected.
Options 0 “Custom V/Hz”
1 “30.0, VT”
2 “35.0, VT”
Variable Torque (Typical fan/pump curves.)
3 “40.0, VT”
4 “45.0, VT”
5 “0.0 no IR”
6 “0.0”
7 “2.5, CT”
[Default for
4.0, 5.5, 7.5 & 11 kW
(5.0, 7.5, 10 & 15 HP)
Drives]
Constant Torque
8 “5.0, CT” (Default)
9 “7.5, CT”
10 “10.0, CT”
11 “12.5, CT”
12 “15.0, CT”
13 “17.5, CT”
14 “20.0, CT”
1/2 [Motor NP Volts]
50
1/2
[Motor NP Hertz]
% P031 [Motor NP Volts]
100
Settings
5-14
0
4
3
2
1
50
% P032 [Motor NP Hertz]
100
PowerFlex 40 Adjustable Frequency AC Drive FRN 1.xx - 6.xx User Manual
Publication 22B-UM001H-EN-E
22B-UM001.book Page 27 Wednesday, January 22, 2014 11:04 AM
Programming and Parameters
3-27
Advanced Program Group (continued)
A085 [Start Boost]
Related Parameter(s): P031, P032, P034, P035,
A084, A086, A087, A088, A125
Sets the boost voltage (% of P031 [Motor NP Volts]) and redefines the Volts per Hz curve when A084
[Boost Select] = 0 “Custom V/Hz” and A125 [Torque Perf Mode] = 0 “V/Hz”.
Drive may add additional voltage unless Option 5 is selected.
Values
Default:
2.5%
Min/Max:
0.0/25.0%
Display:
0.1%
A088 [Maximum Voltage]
A085 [Start Boost]
A086 [Break Voltage]
Voltage
P031 [Motor NP Volts]
A087 [Break Frequency]
A034 [Minimum Freq]
P032 [Motor NP Hertz]
Frequency
A086 [Break Voltage]
P035 [Maximum Freq]
Related Parameter(s): P031, P032, P034, P035,
A084, A085, A087, A088, A125
Sets the frequency where break voltage is applied when A084 [Boost Select] = 0 “Custom V/Hz” and
A125 [Torque Perf Mode] = 0 “V/Hz”
Values
Default:
25.0%
Min/Max:
0.0/100.0%
Display:
0.1%
A087 [Break Frequency]
Related Parameter(s): P031, P032, P034, P035,
A084, A085, A086, A088, A125
Sets the frequency where break frequency is applied when A084 [Boost Select] = 0 “Custom V/Hz”
and A125 [Torque Perf Mode] = 0 “V/Hz”
Values
Default:
15.0 Hz
Min/Max:
0.0/400.0 Hz
Display:
0.1 Hz
PowerFlex 40 Adjustable Frequency AC Drive FRN 1.xx - 6.xx User Manual
Publication 22B-UM001H-EN-E
22B-UM001.book Page 28 Wednesday, January 22, 2014 11:04 AM
3-28
Programming and Parameters
Advanced Program Group (continued)
A088 [Maximum Voltage]
Related Parameter(s): d004, A085, A086, A087
Sets the highest voltage the drive will output.
Values
Default:
Drive Rated Volts
Min/Max:
20/Drive Rated Volts
Display:
1 VAC
A089 [Current Limit 1]
Related Parameter(s): P033, A118
Maximum output current allowed before current limiting occurs.
Values
Drive Rated Amps × 1.5
Default:
Min/Max:
0.1/Drive Rated Amps × 1.8
Display:
0.1 Amps
A090 [Motor OL Select]
Related Parameter(s): P032, P033
Drive provides Class 10 motor overload protection. Settings 0-2 select the derating factor for the I2t
overload function.
Options 0 “No Derate” (Default)
1 “Min Derate”
No Derate
Min Derate
100
100
80
80
60
60
40
40
20
20
0
0
25 50 75 100 125 150 175 200
0
0
25 50 75 100 125 150 175 200
A091 [PWM Frequency]
% of P033 [Motor OL Curent]
2 “Max Derate”
Max Derate
100
80
60
40
20
0
0
25 50 75 100 125 150 175 200
Related Parameter(s): A124
Sets the carrier frequency for the PWM output waveform. The chart below provides derating
guidelines based on the PWM frequency setting.
Important: Ignoring derating guidelines can cause reduced drive performance.
Values
100
96
92
88
84
80
76
72
68
64
60
56
52
1
Default:
4.0 kHz
Min/Max:
2.0/16.0 kHz
Display:
0.1 kHz
2
3
4
5
6
7
8
9 10 11 12 13 14 15 16
PowerFlex 40 Adjustable Frequency AC Drive FRN 1.xx - 6.xx User Manual
Publication 22B-UM001H-EN-E
22B-UM001.book Page 29 Wednesday, January 22, 2014 11:04 AM
Programming and Parameters
3-29
Advanced Program Group (continued)
A092 [Auto Rstrt Tries]
Related Parameter(s): A055, A058, A061, A093
Sets the maximum number of times the drive attempts to reset a fault and restart.
Clear a Type 1 fault and restart the drive.
1. Set A092 [Auto Rstrt Tries] to a value other than “0”.
2. Set A093 [Auto Rstrt Delay] to a value other than “0”.
Clear an OverVoltage, UnderVoltage or Heatsink OvrTmp fault without restarting the drive.
1. Set A092 [Auto Rstrt Tries] to a value other than “0”.
2. Set A093 [Auto Rstrt Delay] to “0”.
!
Values
ATTENTION: Equipment damage and/or personal injury may result if this parameter
is used in an inappropriate application. Do not use this function without considering
applicable local, national and international codes, standards, regulations or industry
guidelines.
Default:
0
Min/Max:
0/9
Display:
1
A093 [Auto Rstrt Delay]
Related Parameter(s): A092
Sets the time between restart attempts when A092 [Auto Rstrt Tries] is set to a value other than zero.
Values
Default:
1.0 Secs
Min/Max:
0.0/300.0 Secs
Display:
0.1 Secs
A094 [Start At PowerUp]
Stop drive before changing this parameter.
Enables/disables a feature that allows a Start or Run command to automatically cause the drive to
resume running at commanded speed after drive input power is restored. Requires a digital input
configured for Run or Start and a valid start contact.
This parameter will not function if parameter P036 [Start Source] is set to 4 “2-W High Speed”.
!
ATTENTION: Equipment damage and/or personal injury may result if this parameter
is used in an inappropriate application. Do not use this function without considering
applicable local, national and international codes, standards, regulations or industry
guidelines.
Options 0 “Disabled” (Default)
1 “Enabled”
PowerFlex 40 Adjustable Frequency AC Drive FRN 1.xx - 6.xx User Manual
Publication 22B-UM001H-EN-E
22B-UM001.book Page 30 Wednesday, January 22, 2014 11:04 AM
3-30
Programming and Parameters
Advanced Program Group (continued)
A095 [Reverse Disable]
Related Parameter(s): d006
Stop drive before changing this parameter.
Enables/disables the function that allows the direction of motor rotation to be changed. The reverse
command may come from a digital command, the keypad or a serial command. All reverse inputs
including two-wire Run Reverse will be ignored with reverse disabled.
Options 0 “Rev Enabled”
(Default)
1 “Rev Disabled”
A096 [Flying Start En]
Sets the condition that allows the drive to reconnect to a spinning motor at actual RPM.
Options 0 “Disabled” (Default)
1 “Enabled”
A097 [Compensation]
Enables/disables correction options that may improve problems with motor instability.
Options 0 “Disabled”
1 “Electrical” (Default)
Some drive/motor combinations have inherent instabilities
which are exhibited as non-sinusodial motor currents. This
setting attempts to correct this condition.
2 “Mechanical”
Some motor/load combinations have mechanical resonances
which can be excited by the drive current regulator. This
setting slows down the current regulator response and
attempts to correct this condition.
3 “Both”
A098 [SW Current Trip]
Related Parameter(s): P033
Enables/disables a software instantaneous (within 100 ms) current trip.
Values
Default:
0.0 (Disabled)
Min/Max:
0.0/(Drive Rated Amps × 2)
Display:
0.1 Amps
A099 [Process Factor]
Related Parameter(s): d010
Scales the output frequency value displayed by d010 [Process Display].
Output
Process
Process
Freq x Factor = Display
Values
Default:
30.0
Min/Max:
0.1/999.9
Display:
0.1
PowerFlex 40 Adjustable Frequency AC Drive FRN 1.xx - 6.xx User Manual
Publication 22B-UM001H-EN-E
22B-UM001.book Page 31 Wednesday, January 22, 2014 11:04 AM
Programming and Parameters
3-31
Advanced Program Group (continued)
A100 [Fault Clear]
Stop drive before changing this parameter.
Resets a fault and clears the fault queue. Used primarily to clear a fault over network
communications.
Options 0 “Ready/Idle” (Default)
1 “Reset Fault”
2 “Clear Buffer”
(Parameters d007-d009 [Fault x Code])
A101 [Program Lock]
Protects parameters against change by unauthorized personnel.
Options 0 “Unlocked” (Default)
1 “Locked”
A102 [Testpoint Sel]
Related Parameter(s): d019
Used by Rockwell Automation field service personnel.
Values
Default:
400
Min/Max:
0/FFFF
Display:
1 Hex
A103 [Comm Data Rate]
Related Parameter(s): d015
Sets the serial port rate for the RS485 (DSI) port.
Important: Power to drive must be cycled before any changes will affect drive operation.
Options 0 “1200”
1 “2400”
2 “4800”
3 “9600” (Default)
4 “19.2K”
5 “38.4K”
A104 [Comm Node Addr]
Related Parameter(s): d015
Sets the drive node address for the RS485 (DSI) port if using a network connection.
Important: Power to drive must be cycled before any changes will affect drive operation.
Values
Default:
100
Min/Max:
1/247
Display:
1
PowerFlex 40 Adjustable Frequency AC Drive FRN 1.xx - 6.xx User Manual
Publication 22B-UM001H-EN-E
22B-UM001.book Page 32 Wednesday, January 22, 2014 11:04 AM
3-32
Programming and Parameters
Advanced Program Group (continued)
A105 [Comm Loss Action]
Related Parameter(s): d015, P037, A106
Selects the drive’s response to a loss of the communication connection or excessive communication
errors.
Options 0 “Fault” (Default)
Drive will fault on an F81 Comm Loss and coast to stop.
1 “Coast Stop”
Stops drive via coast to stop.
2 “Stop”
Stops drive via P037 [Stop Mode] setting.
3 “Continu Last”
Drive continues operating at communication commanded
speed saved in RAM.
A106 [Comm Loss Time]
Related Parameter(s): d015, A105
Sets the time that the drive will remain in communication loss before implementing the option selected
in A105 [Comm Loss Action].
Values
Default:
5.0 Secs
Min/Max:
0.1/60.0 Secs
Display:
0.1 Secs
A107 [Comm Format]
Related Parameter(s): d015
Selects the protocol (RTU only), data bits (8 data bits only), parity (None, Even, Odd), and stop bits (1
stop bit only) used by the RS485 port on the drive.
Refer to Appendix C for details on using the drive communication features.
Important: Power to drive must be cycled before any changes will affect drive operation.
Options 0 “RTU 8-N-1” (Default)
1 “RTU 8-E-1”
2 “RTU 8-O-1”
3 “RTU 8-N-2”
4 “RTU 8-E-2”
5 “RTU 8-O-2”
A108 [Language]
Selects the language displayed by the remote communications option.
Options 1 “English” (Default)
2 “Français”
3 “Español”
4 “Italiano”
5 “Deutsch”
6 “Reserved”
7 “Português”
8 “Reserved”
9 “Reserved”
10 “Nederlands”
PowerFlex 40 Adjustable Frequency AC Drive FRN 1.xx - 6.xx User Manual
Publication 22B-UM001H-EN-E
22B-UM001.book Page 33 Wednesday, January 22, 2014 11:04 AM
Programming and Parameters
3-33
Advanced Program Group (continued)
A109 [Anlg Out Setpt]
Related Parameter(s): A065
When A065 [Analog Out Sel] is set to option 18, 19 or 20, this parameter sets the percentage of
analog output desired.
Values
Default:
0.0%
Min/Max:
0.0/100.0%
Display:
0.1%
A110 [Anlg In 0-10V Lo]
Related Parameter(s): d020, P034, P038, A122
Sets the analog input level that corresponds to P034 [Minimum Freq] if a 0-10V input is used by P038
[Speed Reference].
Analog inversion can be accomplished by setting this value larger than A111 [Anlg In 0-10V Hi].
Values
Default:
0.0%
Min/Max:
0.0/100.0%
Display:
0.1%
P035 [Maximum Freq]
Sp
e
R
ed
efe
re
nc
e
P034 [Minimum Freq]
0
0
A110 [Anlg In 0-10V Lo]
A111 [Anlg In 0-10V Hi]
A111 [Anlg In 0-10V Hi]
Related Parameter(s): d020, P035, P038, A122, A123
Sets the analog input level that corresponds to P035 [Maximum Freq] if a 0-10V input is used by P038
[Speed Reference].
Analog inversion can be accomplished by setting this value smaller than A110 [Anlg In 0-10V Lo].
Values
Default:
100.0%
Min/Max:
0.0/100.0%
Display:
0.1%
A112 [Anlg In4-20mA Lo]
Related Parameter(s): d021, P034, P038
Sets the analog input level that corresponds to P034 [Minimum Freq] if a 4-20mA input is used by
P038 [Speed Reference].
Analog inversion can be accomplished by setting this value larger than A113 [Anlg In4-20mA Hi].
Values
Default:
0.0%
Min/Max:
0.0/100.0%
Display:
0.1%
PowerFlex 40 Adjustable Frequency AC Drive FRN 1.xx - 6.xx User Manual
Publication 22B-UM001H-EN-E
22B-UM001.book Page 34 Wednesday, January 22, 2014 11:04 AM
3-34
Programming and Parameters
Advanced Program Group (continued)
A113 [Anlg In4-20mA Hi]
Related Parameter(s): d021, P035, P038
Sets the analog input level that corresponds to P035 [Maximum Freq] if a 4-20mA input is used by
P038 [Speed Reference].
Analog inversion can be accomplished by setting this value smaller than A112 [Anlg In4-20mA Lo].
Values Default:
100.0%
Min/Max:
0.0/100.0%
Display:
0.1%
A114 [Slip Hertz @ FLA]
Related Parameter(s): P033
Compensates for the inherent slip in an induction motor. This frequency is added to the commanded
output frequency based on motor current.
Values Default:
2.0 Hz
Min/Max:
0.0/10.0 Hz
Display:
0.1 Hz
A115 [Process Time Lo]
Related Parameter(s): d010, P034
Scales the time value when the drive is running at P034 [Minimum Freq]. When set to a value other
than zero, d010 [Process Display] indicates the duration of the process.
Values Default:
0.00
Min/Max:
0.00/99.99
Display:
0.01
A116 [Process Time Hi]
Related Parameter(s): d010, P035
Scales the time value when the drive is running at P035 [Maximum Freq]. When set to a value other
than zero, d010 [Process Display] indicates the duration of the process.
Values Default:
0.00
Min/Max:
0.00/99.99
Display:
0.01
A117 [Bus Reg Mode]
Controls the operation of the drive voltage regulation, which is normally operational at decel or when
the bus voltage rises.
Refer to the Attention statement on page P-3 for important information on bus regulation.
Options 0 “Disabled”
1 “Enabled” (Default)
A118 [Current Limit 2]
Related Parameter(s): P033, A051-A054, A089
Maximum output current allowed before current limiting occurs. This parameter is only active if
A051 - A054 [Digital Inx Sel] is set to 25 “Current Lmt2” and is active.
Values
Default:
Drive Rated Amps × 1.5
Min/Max:
Display:
0.1/(Drive Rated Amps × 1.8)
0.1 Amps
PowerFlex 40 Adjustable Frequency AC Drive FRN 1.xx - 6.xx User Manual
Publication 22B-UM001H-EN-E
22B-UM001.book Page 35 Wednesday, January 22, 2014 11:04 AM
Programming and Parameters
3-35
Advanced Program Group (continued)
A119 [Skip Frequency]
Related Parameter(s): A120
Sets the frequency at which the drive will not operate.
A setting of 0 disables this parameter.
Values
Default:
0 Hz
Min/Max:
0/400 Hz
Display:
1 Hz
A120 [Skip Freq Band]
Related Parameter(s): A119
Determines the bandwidth around A119 [Skip Frequency]. A120 [Skip Frequency Band] is split
applying 1/2 above and 1/2 below the actual skip frequency.
A setting of 0.0 disables this parameter.
Values
Default:
0.0 Hz
Min/Max:
0.0/30.0 Hz
Display:
0.1 Hz
Frequency
Command
Frequency
Drive Output
Frequency
2x Skip
Frequency Band
Skip Frequency
Time
A121 [Stall Fault Time]
Sets the time that the drive will remain in stall mode before a fault is issued.
Options 0 “60 Seconds” (Default)
1 “120 Seconds”
2 “240 Seconds”
3 “360 Seconds”
4 “480 Seconds”
5 “Flt Disabled”
PowerFlex 40 Adjustable Frequency AC Drive FRN 1.xx - 6.xx User Manual
Publication 22B-UM001H-EN-E
22B-UM001.book Page 36 Wednesday, January 22, 2014 11:04 AM
3-36
Programming and Parameters
Advanced Program Group (continued)
A122 [Analog In Loss]
Related Parameter(s): A110, A111, A132
Selects drive action when an input signal loss is detected. Signal loss is defined as an analog signal
less than 1V or 2mA. The signal loss event ends and normal operation resumes when the input signal
level is greater than or equal to 1.5V or 3mA. If using a 0-10V analog input, set A110 [Anlg In 0-10V
Lo] to a minimum of 20% (i.e. 2 volts).
Options 0 “Disabled” (Default)
1 “Fault (F29)”
F29 Analog Input Loss
2 “Stop”
Uses P037 [Stop Mode]
3 “Zero Ref”
Drive runs at zero speed reference.
4 “Min Freq Ref”
Drive runs at minimum frequency.
5 “Max Freq Ref”
Drive runs at maximum frequency.
6 “Int Freq Ref”
Drive runs at internal frequency.
A123 [10V Bipolar Enbl]
Related Parameter(s): P038, A111
Enables/disables bipolar control. In bipolar mode direction is commanded by the sign of the reference.
Options 0 “Uni-Polar In” (Default) 0 to 10V only
1 “Bi-Polar In”
±10V
A124 [Var PWM Disable]
Related Parameter(s): A091
Stop drive before changing this parameter.
Enables/disables a feature that varies the carrier frequency for the PWM output waveform defined by
A091 [PWM Frequency].
Disabling this feature when low frequency conditions exist may result in IGBT stress and nuisance
tripping.
Options 0 “Enabled” (Default)
1 “Disabled”
A125 [Torque Perf Mode]
Related Parameter(s): A084, A085, A086, A087, A127
Stop drive before changing this parameter.
Enables/disables sensorless vector control operation.
Options 0 “V/Hz”
1 “Sensrls Vect” (Default)
A126 [Motor NP FLA]
Related Parameter(s): A127
Set to the motor nameplate rated full load amps.
Values
Default:
Drive Rated Amps
Min/Max:
0.1/(Drive Rated Amps × 2)
Display:
0.1 Amps
PowerFlex 40 Adjustable Frequency AC Drive FRN 1.xx - 6.xx User Manual
Publication 22B-UM001H-EN-E
22B-UM001.book Page 37 Wednesday, January 22, 2014 11:04 AM
Programming and Parameters
3-37
Advanced Program Group (continued)
A127 [Autotune]
Related Parameter(s): A125, A126, A128, A129
Stop drive before changing this parameter.
Provides an automatic method for setting A128 [IR Voltage Drop] and A129 [Flux Current Ref], which
affect sensorless vector performance. Parameter A126 [Motor NP FLA] must be set to the motor
nameplate full load amps before running the Autotune procedure.
Options 0 “Ready/Idle” (Default)
1 “Static Tune”
2 “Rotate Tune”
“Ready” (0) = Parameter returns to this setting following a “Static Tune” or “Rotate Tune.”
“Static Tune” (1) = A temporary command that initiates a non-rotational motor stator resistance test for
the best possible automatic setting of A128 [IR Voltage Drop]. A start command is required following
initiation of this setting. The parameter returns to “Ready” (0) following the test, at which time another
start transition is required operate the drive in normal mode. Used when motor cannot be uncoupled
from the load.
“Rotate Tune” (2) = A temporary command that initiates a “Static Tune” followed by a rotational test
for the best possible automatic setting of A129 [Flux Current Ref]. A start command is required
following initiation of this setting. The parameter returns to “Ready” (0) following the test, at which time
another start transition is required to operate the drive in normal mode. Important: Used when motor
is uncoupled from the load. Results may not be valid if a load is coupled to the motor during this
procedure.
!
ATTENTION: Rotation of the motor in an undesired direction can occur during this
procedure. To guard against possible injury and/or equipment damage, it is
recommended that the motor be disconnected from the load before proceeding.
If the Autotune routine fails, an F80 SVC Autotune fault is displayed.
A128 [IR Voltage Drop]
Related Parameter(s): A127
Value of volts dropped across the resistance of the motor stator.
Values
Default:
Based on Drive Rating
Min/Max:
0.0/230.0 VAC
Display:
0.1 VAC
A129 [Flux Current Ref]
Related Parameter(s): A127
Value of amps for full motor flux.
Values
Default:
Based on Drive Rating
Min/Max:
0.00/[Motor NP FLA]
Display:
0.01 Amps
PowerFlex 40 Adjustable Frequency AC Drive FRN 1.xx - 6.xx User Manual
Publication 22B-UM001H-EN-E
22B-UM001.book Page 38 Wednesday, January 22, 2014 11:04 AM
3-38
Programming and Parameters
Advanced Program Group (continued)
A130 [PID Trim Hi]
Sets the maximum positive value that is added to the speed reference when PID trim is used.
Values
Default:
60.0
Min/Max:
0.0/400.0
Display:
0.1
A131 [PID Trim Lo]
Sets the maximum positive value that is subtracted from the PID reference when PID trim is used.
Values
Default:
0.0
Min/Max:
0.0/400.0
Display:
0.1
A132 [PID Ref Sel]
Related Parameter(s): P038, A122
Stop drive before changing this parameter.
Enables/disables PID mode and selects the source of the PID reference. Refer to Appendix F for
details.
Options 0 “PID Disabled”
(Default)
1 “PID Setpoint”
2 “0-10V Input”
3 “4-20mA Input”
4 “Comm Port”
5 “Setpnt, Trim”
6 “0-10V, Trim”
7 “4-20mA, Trim”
8 “Comm, Trim”
A133 [PID Feedback Sel]
Select the source of the PID feedback. Refer to Appendix F for details.
Options 0 “0-10V Input” (Default) The PID will not function with a bipolar input. Negative
voltages are treated as 0 volts.
1 “4-20mA Input”
2 “Comm Port”
A134 [PID Prop Gain]
Sets the value for the PID proportional component when the PID mode is enabled by A132 [PID Ref
Sel].
Values
Default:
0.01
Min/Max:
0.00/99.99
Display:
0.01
PowerFlex 40 Adjustable Frequency AC Drive FRN 1.xx - 6.xx User Manual
Publication 22B-UM001H-EN-E
22B-UM001.book Page 39 Wednesday, January 22, 2014 11:04 AM
Programming and Parameters
3-39
Advanced Program Group (continued)
A135 [PID Integ Time]
Sets the value for the PID integral component when the PID mode is enabled by A132 [PID Ref Sel].
Values
Default:
0.1 Secs
Min/Max:
0.0/999.9 Secs
Display:
0.1 Secs
A136 [PID Diff Rate]
Sets the value for the PID differential component when the PID mode is enabled by A132 [PID Ref
Sel].
Values
Default:
0.01 (1/Secs)
Min/Max:
0.00/99.99 (1/Secs)
Display:
0.01 (1/Secs)
A137 [PID Setpoint]
Provides an internal fixed value for process setpoint when the PID mode is enabled by A132 [PID Ref
Sel].
Values
Default:
0.0%
Min/Max:
0.0/100.0%
Display:
0.1%
A138 [PID Deadband]
Sets the lower limit of the PID output.
Values
Default:
0.0%
Min/Max:
0.0/10.0%
Display:
0.1%
A139 [PID Preload]
Sets the value used to preload the integral component on start or enable.
Values
Default:
0.0 Hz
Min/Max:
0.0/400.0 Hz
Display:
0.1 Hz
PowerFlex 40 Adjustable Frequency AC Drive FRN 1.xx - 6.xx User Manual
Publication 22B-UM001H-EN-E
22B-UM001.book Page 40 Wednesday, January 22, 2014 11:04 AM
3-40
Programming and Parameters
Advanced Program Group (continued)
A140 [Stp Logic 0]
A141 [Stp Logic 1]
A142 [Stp Logic 2]
A143 [Stp Logic 3]
A144 [Stp Logic 4]
A145 [Stp Logic 5]
A146 [Stp Logic 6]
A147 [Stp Logic 7]
Values
Default:
Related Parameter(s): P038, P039, P040, A051-A054,
A055, A058, A061, A067, A068, A070-A077, A150-A157
Stop drive before changing this parameter.
00F1
Min/Max:
0001/bAFF
Display:
4 Digits
Parameters A140-A147 are only active if P038 [Speed Reference] is set to 6 “Stp Logic”.
These parameters can be used to create a custom profile of frequency commands. Each “step” can
be based on time, status of a Logic input or a combination of time and the status of a Logic input.
Digits 0-3 for each [Stp Logic x] parameter must be programmed according to the desired profile.
A Logic input is established by setting a digital input, parameters A051 - A054 [Digital Inx Sel], to 23
“Logic In1” and/or 24 “Logic In2”.
A time interval between steps can be programmed using parameters A150 - A157 [Stp Logic Time x].
See the table below for related parameters.
The speed for any step is programmed using parameters A070 - A077 [Preset Freq x].
StepLogic Parameter
(Active when P038 = 6 “Stp Logic”)
Related Preset Frequency Parameter
(Can be activated independent of
StepLogic Parameters)
Related StepLogic Time Parameter
(Active when A140-A147 Digit 0 or 1
are set to 1, b, C, d or E)
A140 [Stp Logic 0]
A070 [Preset Freq 0]
A150 [Stp Logic Time 0]
A141 [Stp Logic 1]
A071 [Preset Freq 1]
A151 [Stp Logic Time 1]
A142 [Stp Logic 2]
A072 [Preset Freq 2]
A152 [Stp Logic Time 2]
A143 [Stp Logic 3]
A073 [Preset Freq 3]
A153 [Stp Logic Time 3]
A144 [Stp Logic 4]
A074 [Preset Freq 4]
A154 [Stp Logic Time 4]
A145 [Stp Logic 5]
A075 [Preset Freq 5]
A155 [Stp Logic Time 5]
A146 [Stp Logic 6]
A076 [Preset Freq 6]
A156 [Stp Logic Time 6]
A147 [Stp Logic 7]
A077 [Preset Freq 7]
A157 [Stp Logic Time 7]
How StepLogic Works
The StepLogic sequence begins with a valid start command. A normal sequence always begins with
A140 [Stp Logic 0].
Digit 0: Logic For Next Step
This digit defines the logic for the next step. When the condition is met the program advances to the
next step. Step 0 follows Step 7. Example: Digit 0 is set 3. When “Logic In2” becomes active, the
program advances to the next step.
Digit 1: Logic to Jump to a Different Step
For all settings other than F, when the condition is met, the program overrides Digit 0 and jumps to the
step defined by Digit 2.
Digit 2: Different Step to Jump
When the condition for Digit 1 is met, the Digit 2 setting determines the next step or to end the program.
PowerFlex 40 Adjustable Frequency AC Drive FRN 1.xx - 6.xx User Manual
Publication 22B-UM001H-EN-E
22B-UM001.book Page 41 Wednesday, January 22, 2014 11:04 AM
Programming and Parameters
3-41
Digit 3: Step Settings
This digit defines what accel/decel profile the speed command will follow and the direction of the
command for the current step. In addition, if a relay or opto output (parameters A055, A058 and A061)
is set to 15 “StpLogic Out”, this parameter can control the status of that output.
Any StepLogic parameter can be programmed to control a relay or opto output, but you can not
control different outputs based on the condition of different StepLogic commands.
StepLogic Settings
The logic for each function is determined by the four digits for each StepLogic parameter. The
following is a listing of the available settings for each digit.
Refer to Appendix E for details.
Logic For Next Step
Logic to Jump to a Different Step
Different Step to Jump
Step Settings
Digit 3 Settings
Required
Setting
0
1
2
3
4
5
6
7
8
9
A
b
Accel/Decel
Param. Used
Accel/Decel 1
Accel/Decel 1
Accel/Decel 1
Accel/Decel 1
Accel/Decel 1
Accel/Decel 1
Accel/Decel 2
Accel/Decel 2
Accel/Decel 2
Accel/Decel 2
Accel/Decel 2
Accel/Decel 2
Digit 2 Settings
0 = Jump to Step 0
1 = Jump to Step 1
2 = Jump to Step 2
3 = Jump to Step 3
4 = Jump to Step 4
5 = Jump to Step 5
6 = Jump to Step 6
7 = Jump to Step 7
8 = End Program (Normal Stop)
9 = End Program (Coast to Stop)
A = End Program and Fault (F2)
StepLogic
Output State
Off
Off
Off
On
On
On
Off
Off
Off
On
On
On
Digit 0
Digit 1
Digit 2
Digit 3
Commanded
Direction
FWD
REV
No Output
FWD
REV
No Output
FWD
REV
No Output
FWD
REV
No Output
Digit 1 and Digit 0 Settings
0 = Skip Step (Jump Immediately)
1 = Step Based on [Stp Logic Time x]
2 = Step if “Logic In1” is Active
3 = Step if “Logic In2” is Active
4 = Step if “Logic In1” is Not Active
5 = Step if “Logic In2” is Not Active
6 = Step if either “Logic In1” or “Logic In2” is Active
7 = Step if both “Logic In1” and “Logic In2” is Active
8 = Step if neither “Logic In1” or “Logic In2” is Active
9 = Step if “Logic In1” is Active and “Logic In2” is Not Active
A = Step if “Logic In2” is Active and “Logic In1” is Not Active
b = Step after [Stp Logic Time x] and “Logic In1” is Active
C = Step after [Stp Logic Time x] and “Logic In2” is Active
d = Step after [Stp Logic Time x] and “Logic In1” is Not Active
E = Step after [Stp Logic Time x] and “Logic In2” is Not Active
F = Do Not Step/Ignore Digit 2 Settings
PowerFlex 40 Adjustable Frequency AC Drive FRN 1.xx - 6.xx User Manual
Publication 22B-UM001H-EN-E
22B-UM001.book Page 42 Wednesday, January 22, 2014 11:04 AM
3-42
Programming and Parameters
Advanced Program Group (continued)
A150 [Stp Logic Time 0]
A151 [Stp Logic Time 1]
A152 [Stp Logic Time 2]
A153 [Stp Logic Time 3]
A154 [Stp Logic Time 4]
A155 [Stp Logic Time 5]
A156 [Stp Logic Time 6]
A157 [Stp Logic Time 7]
Related Parameter(s): P038, A055, A058, A061,
A070-A077, A140-A147
Sets the time to remain in each step if the corresponding StpLogic command word is set to “Step after
Time”.
Values
Default:
30.0 Secs
Min/Max:
0.0/999.9 Secs
Display:
0.1 Secs
A160 [EM Brk Off Delay]
Related Parameter(s): P037
Sets the time the drive remains at minimum frequency before the relay or an opto output is energized
and the drive ramps to the commanded frequency.
The relay or opto output is typically connected to a user-supplied electromechanical brake coil relay.
Set P037 [Stop Mode] to 8 “Ramp+EM B,CF” or 9 “Ramp+EM Brk” to enable the electromechanical
brake option.
Set A055 [Relay Out Sel], A058 or A061 [Opto Outx Sel] to 22 “EM Brk Cntrl” to control brake
operation.
Values Default:
2.00 Secs
Min/Max:
0.01/10.00 Secs
Display:
0.01 Secs
Frequency
Ra
mp
Ra
mp
Ac
ce
l
A160 [EM Brk Off Delay]
A161 [EM Brk On Delay]
De
ce
l
Minimum Freq
Start
Commanded
EM Brk
Energized (Off)
Time
Stop
Commanded
EM Brk
De-Energized (On)
PowerFlex 40 Adjustable Frequency AC Drive FRN 1.xx - 6.xx User Manual
Publication 22B-UM001H-EN-E
Drive Stops
22B-UM001.book Page 43 Wednesday, January 22, 2014 11:04 AM
Programming and Parameters
3-43
Advanced Program Group (continued)
A161 [EM Brk On Delay]
Related Parameter(s): P037
Sets the time the drive remains at minimum frequency before the relay or an opto output is
de-energizing and the drive stops.
The relay or opto output is typically connected to a user-supplied electromechanical brake coil relay.
Set P037 [Stop Mode] to 8 “Ramp+EM B,CF” or 9 “Ramp+EM Brk” to enable the electromechanical
brake option.
Set A055 [Relay Out Sel], A058 or A061 [Opto Outx Sel] to 22 “EM Brk Cntrl” to control brake
operation.
Values Default:
2.00 Secs
Min/Max:
0.01/10.00 Secs
Display:
0.01 Secs
A162 [MOP Reset Sel]
Related Parameter(s): A069
Set the drive to save the current MOP reference command.
Options 0 “Zero MOP Ref”
1 “Save MOP Ref”
(Default)
This option clamps A069 [Internal Freq] at 0.0 Hz when the
drive is not running.
Reference is saved in A069 [Internal Freq].
A163 [DB Threshold]
Related Parameter(s): P037, A080, A081, A082
Sets the DC bus Voltage Threshold for Dynamic Brake operation. If the DC bus voltage falls below the
value set in this parameter, the Dynamic Brake will not turn on. Lower values will make the Dynamic
Braking function more responsive but may result in nuisance Dynamic Brake activation.
Values
Default
100.0%
Min/Max:
0.0/110.0%
Display:
0.0%
!
ATTENTION: Equipment damage may result if this parameter is set a
value that causes the dynamic braking resistor to dissipate excessive power.
Parameter settings less than 100% should be carefully evaluated to ensure
that the dynamic brake resistor’s wattage rating is not exceeded. In general,
values less than 90% are not needed. This parameter’s setting is especially
important if parameter A082 [DB Resistor Sel] is set to 2 “No Protection”.
PowerFlex 40 Adjustable Frequency AC Drive FRN 1.xx - 6.xx User Manual
Publication 22B-UM001H-EN-E
22B-UM001.book Page 44 Wednesday, January 22, 2014 11:04 AM
3-44
Programming and Parameters
Advanced Program Group (continued)
A164 [Comm Write Mode]
Determines whether parameter changes made over communication port are saved and stored in
Non-Volatile Storage (NVS) or RAM only. If they are stored in RAM, the values will be lost at
power-down.
Options 0 “Save” (Default)
1 “RAM Only”
!
ATTENTION: Risk of equipment damage exists. If a controller is programmed to
write parameter data to Non-Volatile Storage (NVS) frequently, the NVS will quickly
exceed its life cycle and cause the drive to malfunction. Do not create a program that
frequently uses configurable outputs to write parameter data to NVS unless A164
[Comm Write Mode] is set to option 1.
A165 [Anlg Loss Delay]
Related Parameter(s): A122
Sets the length of time after power-up during which the drive will not detect an analog signal loss. The
drive response to an analog signal loss is set in A122 [Analog In Loss].
Values
Default:
0.0 Secs
Min/Max:
0.0/20.0 Secs
Display:
0.1 Secs
A166 [Analog In Filter]
Sets level of additional filtering of the analog input signals. A higher number increases filtering and
decreases bandwidth. Each setting doubles the applied filtering (1 = 2x filter, 2 = 4x filter, etc...). No
additional filtering is applied when set to “0”.
Values
Default:
0
Min/Max:
0/14
Display:
1
A167 [PID Invert Error]
When set to “Inverted”, changes the sign of the PID error. This causes an increase in the drive output
frequency with PID Feedback greater than PID Setpoint, and a decrease in drive output frequency
with PID Feedback less than PID Setpoint.
Options 0 “Not Inverted” (Default)
1 “Inverted”
PowerFlex 40 Adjustable Frequency AC Drive FRN 1.xx - 6.xx User Manual
Publication 22B-UM001H-EN-E
22B-UM001.book Page 45 Wednesday, January 22, 2014 11:04 AM
Programming and Parameters
3-45
Parameter Cross Reference – by Name
Parameter Name
No.
Group
Parameter Name
No.
Group
10V Bipolar Enbl
Accel Time 1
Accel Time 2
Analog In 0-10V
Analog In 4-20mA
Analog In Filter
Analog In Loss
Analog Out High
Analog Out Sel
Anlg In 0-10V Hi
Anlg In 0-10V Lo
Anlg In4-20mA Hi
Anlg In4-20mA Lo
Anlg Loss Delay
Anlg Out Setpt
Auto Rstrt Delay
Auto Rstrt Tries
Autotune
Boost Select
Break Frequency
Break Voltage
Bus Reg Mode
Comm Data Rate
Comm Format
Comm Loss Action
Comm Loss Time
Comm Node Addr
Comm Status
Comm Write Mode
Commanded Freq
Compensation
Contrl In Status
Control Source
Control SW Ver
Counter Status
Current Limit x
DB Resistor Sel
DB Threshold
DC Brake Level
DC Brake Time
DC Bus Voltage
Decel Time 1
Decel Time 2
Dig In Status
Digital Inx Sel
Drive Status
Drive Temp
Drive Type
Elapsed Run Time
EM Brk Off Delay
EM Brk On Delay
Fault Clear
Fault x Code
Flux Current Ref
Flying Start En
Internal Freq
IR Voltage Drop
A123
P039
A067
d020
d021
A166
A122
A066
A065
A111
A110
A113
A112
A166
A109
A093
A092
A127
A084
A087
A086
A117
A103
A107
A105
A106
A104
d015
A164
d002
A097
d013
d012
d016
d025
A089, A118
A082
A163
A081
A080
d005
P040
A068
d014
A051-A054
d006
d024
d017
d018
A160
A161
A100
d007-d009
A129
A096
A069
A128
Advanced Program
Basic Program
Advanced Program
Display
Display
Advanced Program
Advanced Program
Advanced Program
Advanced Program
Advanced Program
Advanced Program
Advanced Program
Advanced Program
Advanced Program
Advanced Program
Advanced Program
Advanced Program
Advanced Program
Advanced Program
Advanced Program
Advanced Program
Advanced Program
Advanced Program
Advanced Program
Advanced Program
Advanced Program
Advanced Program
Display
Advanced Program
Display
Advanced Program
Display
Display
Display
Display
Advanced Program
Advanced Program
Advanced Program
Advanced Program
Advanced Program
Display
Basic Program
Advanced Program
Display
Advanced Program
Display
Display
Display
Display
Advanced Program
Advanced Program
Advanced Program
Display
Advanced Program
Advanced Program
Advanced Program
Advanced Program
Jog Accel/Decel
Jog Frequency
Language
Maximum Freq
Maximum Voltage
Minimum Freq
MOP Reset Sel
Motor NP FLA
Motor NP Hertz
Motor NP Volts
Motor OL Current
Motor OL Ret
Motor OL Select
Opto Out Logic
Opto Outx Level
Opto Outx Sel
Output Current
Output Freq
Output Power
Output Powr Fctr
Output Voltage
PID Deadband
PID Diff Rate
PID Feedback Sel
PID Integ Time
PID Invert Error
PID Preload
PID Prop Gain
PID Ref Sel
PID Setpoint
PID Trim Hi
PID Trim Lo
Preset Freq x
Process Display
Process Factor
Process Time Hi
Process Time Lo
Program Lock
PWM Frequency
Relay Out Level
Relay Out Sel
Reset To Defalts
Reverse Disable
S Curve %
Skip Freq Band
Skip Frequency
Slip Hertz @ FLA
Stp Logic Status
Stp Logic x
Stp Logic Time x
Speed Reference
Stall Fault Time
Start At PowerUp
Start Boost
Start Source
Stop Mode
SW Current Trip
A079
A078
A108
P035
A088
P034
A162
A126
P032
P031
P033
P043
A090
A064
A059, A062
A058, A061
d003
d001
d022
d023
d004
A138
A136
A133
A135
A167
A139
A134
A132
A137
A130
A131
A070-A077
d010
A099
A116
A115
A101
A091
A056
A055
P041
A095
A083
A120
A119
A114
d028
A140-A147
A150-A157
P038
A121
A094
A085
P036
P037
A098
Advanced Program
Advanced Program
Advanced Program
Basic Program
Advanced Program
Basic Program
Advanced Program
Advanced Program
Basic Program
Basic Program
Basic Program
Basic Program
Advanced Program
Advanced Program
Advanced Program
Advanced Program
Display
Display
Display
Display
Display
Advanced Program
Advanced Program
Advanced Program
Advanced Program
Advanced Program
Advanced Program
Advanced Program
Advanced Program
Advanced Program
Advanced Program
Advanced Program
Advanced Program
Display
Advanced Program
Advanced Program
Advanced Program
Advanced Program
Advanced Program
Advanced Program
Advanced Program
Basic Program
Advanced Program
Advanced Program
Advanced Program
Advanced Program
Advanced Program
Display
Advanced Program
Advanced Program
Basic Program
Advanced Program
Advanced Program
Advanced Program
Basic Program
Basic Program
Advanced Program
PowerFlex 40 Adjustable Frequency AC Drive FRN 1.xx - 6.xx User Manual
Publication 22B-UM001H-EN-E
22B-UM001.book Page 46 Wednesday, January 22, 2014 11:04 AM
3-46
Programming and Parameters
Parameter Name
No.
Group
Testpoint Data
Testpoint Sel
Timer Status
Torque Current
Torque Perf Mode
Var PWM Disable
Voltage Class
d019
A102
d026
d029
A125
A124
P042
Display
Advanced Program
Display
Display
Advanced Program
Advanced Program
Basic Program
PowerFlex 40 Adjustable Frequency AC Drive FRN 1.xx - 6.xx User Manual
Publication 22B-UM001H-EN-E
22B-UM001.book Page 1 Wednesday, January 22, 2014 11:04 AM
Chapter 4
Troubleshooting
Chapter 4 provides information to guide you in troubleshooting the
PowerFlex 40 drive. Included is a listing and description of drive faults
(with possible solutions, when applicable).
For information on…
Drive Status
Faults
See page… For information on…
4-1
Fault Descriptions
4-1
Common Symptoms and
Corrective Actions
See page…
4-3
4-5
Drive Status
The condition or state of your drive is constantly monitored. Any
changes will be indicated through the integral keypad.
LED Indications
See page 2-4 for information on drive status indicators and controls.
Faults
A fault is a condition that stops the drive. There are two fault types.
Type Fault Description
➀ Auto-Reset/Run When this type of fault occurs, and A092 [Auto Rstrt Tries] is
set to a value greater than “0,” a user-configurable timer, A093
[Auto Rstrt Delay], begins. When the timer reaches zero, the
drive attempts to automatically reset the fault. If the condition
that caused the fault is no longer present, the fault will be reset
and the drive will be restarted.
Non-Resetable
This
type of fault may require drive or motor repair, or is
➁
caused by wiring or programing errors. The cause of the fault
must be corrected before the fault can be cleared.
PowerFlex 40 Adjustable Frequency AC Drive FRN 1.xx - 6.xx User Manual
Publication 22B-UM001H-EN-E
22B-UM001.book Page 2 Wednesday, January 22, 2014 11:04 AM
4-2
Troubleshooting
Fault Indication
Condition
Display
Drive is indicating a fault.
The integral keypad provides visual notification of a
fault condition by displaying the following.
• Flashing fault number
• Flashing fault indicator
Press the Escape key to regain control of the
integral keypad.
RUN
FWD
REV
VOLTS
AMPS
HERTZ
PRGOGRAM
FAULT
Manually Clearing Faults
Step
Key(s)
1. Press Esc to acknowledge the fault. The fault information will be
removed so that you can use the integral keypad.
Access d007 [Fault 1 Code] to view the most recent fault information.
2. Address the condition that caused the fault.
The cause must be corrected before the fault can be cleared.
See Table 4.A.
3. After corrective action has been taken, clear the fault by one of these
methods.
• Press Stop if P037 [Stop Mode] is set to a value between “0” and “3”.
• Cycle drive power.
• Set A100 [Fault Clear] to “1” or “2”.
• Cycle digital input if A051-A054 [Digital Inx Sel] is set to option 7
“Clear Fault”.
Automatically Clearing Faults
Option / Step
Clear a Type 1 fault and restart the drive.
1. Set A092 [Auto Rstrt Tries] to a value other than “0”.
2. Set A093 [Auto Rstrt Delay] to a value other than “0”.
Clear an OverVoltage, UnderVoltage or Heatsink OvrTmp fault
without restarting the drive.
1. Set A092 [Auto Rstrt Tries] to a value other than “0”.
2. Set A093 [Auto Rstrt Delay] to “0”.
Auto Restart (Reset/Run)
The Auto Restart feature provides the ability for the drive to
automatically perform a fault reset followed by a start attempt without
user or application intervention. This allows remote or “unattended”
operation. Only certain faults are allowed to be reset. Certain faults
(Type 2) that indicate possible drive component malfunction are not
resettable.
Caution should be used when enabling this feature, since the drive will
attempt to issue its own start command based on user selected programming.
PowerFlex 40 Adjustable Frequency AC Drive FRN 1.xx - 6.xx User Manual
Publication 22B-UM001H-EN-E
22B-UM001.book Page 3 Wednesday, January 22, 2014 11:04 AM
Troubleshooting
4-3
Fault Descriptions
Type(1)
Table 4.A Fault Types, Descriptions and Actions
No.
F2
Fault
Auxiliary Input
F3
Power Loss
➁
F4
UnderVoltage
➀
F5
OverVoltage
➀
F6
Motor Stalled
➀
F7
Motor Overload
➀
F8
Heatsink
OvrTmp
➀
F12
HW OverCurrent
➁
F13
Ground Fault
➁
F29
Analog Input
Loss
➀
➀
Description
Auxiliary input interlock is open.
Action
1. Check remote wiring.
2. Verify communications
programming for intentional fault.
Excessive DC Bus voltage ripple. 1. Monitor the incoming line for
phase loss or line imbalance.
2. Check input line fuse.
DC bus voltage fell below the
Monitor the incoming AC line for low
minimum value.
voltage or line power interruption.
DC bus voltage exceeded
Monitor the AC line for high line
maximum value.
voltage or transient conditions. Bus
overvoltage can also be caused by
motor regeneration. Extend the
decel time or install dynamic brake
option.
Drive is unable to accelerate
Increase P039 - A067 [Accel Time x]
motor.
or reduce load so drive output
current does not exceed the current
set by parameter A089 [Current
Limit 1].
Internal electronic overload trip. 1. An excessive motor load exists.
Reduce load so drive output
current does not exceed the
current set by parameter P033
[Motor OL Current].
2. Verify A084 [Boost Select]
setting
Heatsink temperature exceeds a 1. Check for blocked or dirty heat
predefined value.
sink fins. Verify that ambient
temperature has not exceeded
40°C (104°F) for IP30, NEMA UL
Type 1 installations or 50°C (122°F)
for IP20/Open type installations.
2. Check fan.
The drive output current has
Check programming. Check for
exceeded the hardware current excess load, improper A084 [Boost
Select] setting, DC brake volts set
limit.
too high or other causes of excess
current.
A current path to earth ground
Check the motor and external wiring
has been detected at one or
to the drive output terminals for a
more of the drive output
grounded condition.
terminals.
An analog input is configured to 1. Check parameters.
fault on signal loss. A signal loss 2. Check for broken/loose
has occurred.
connections at inputs.
Configure with A122 [Analog In
Loss].
PowerFlex 40 Adjustable Frequency AC Drive FRN 1.xx - 6.xx User Manual
Publication 22B-UM001H-EN-E
22B-UM001.book Page 4 Wednesday, January 22, 2014 11:04 AM
(1)
Troubleshooting
See page 4-1 for a description of fault types.
Type(1)
4-4
No.
F33
Fault
Auto Rstrt Tries
F38
F39
F40
Phase U to Gnd
Phase V to Gnd
Phase W to Gnd
➁
F41
F42
F43
Phase UV Short
Phase UW Short
Phase VW Short
➁
F48
Params
Defaulted
F63
SW OverCurrent
➀
F64
Drive Overload
➁
F70
Power Unit
➁
F71
Net Loss
F80
SVC Autotune
F81
Comm Loss
➁
➁
Description
Drive unsuccessfully attempted
to reset a fault and resume
running for the programmed
number of A092 [Auto Rstrt
Tries].
A phase to ground fault has been
detected between the drive and
motor in this phase.
Action
Correct the cause of the fault and
manually clear.
1. Check the wiring between the
drive and motor.
2. Check motor for grounded
phase.
3. Replace drive if fault cannot be
cleared.
Excessive current has been
1. Check the motor and drive output
detected between these two
terminal wiring for a shorted
output terminals.
condition.
2. Replace drive if fault cannot be
cleared.
The drive was commanded to
1. Clear the fault or cycle power to
write default values to EEPROM.
the drive.
2. Program the drive parameters as
needed.
Programmed A098 [SW Current Check load requirements and A098
Trip] has been exceeded.
[SW Current Trip] setting.
Drive rating of 150% for 1 minute Reduce load or extend Accel Time.
or 200% for 3 seconds has been
exceeded.
Failure has been detected in the 1. Cycle power.
drive power section.
2. Replace drive if fault cannot be
cleared.
The communication network has 1. Cycle power.
faulted.
2. Check communications cabling.
3. Check network adapter setting.
4. Check external network status.
The autotune function was either Restart procedure.
cancelled by the user or failed.
RS485 (DSI) port stopped
1. If adapter was not intentionally
communicating.
disconnected, check wiring to the
port. Replace wiring, port
expander, adapters or complete
drive as required.
2. Check connection.
3. An adapter was intentionally
disconnected.
4. Turn off using A105 [Comm Loss
Action].
PowerFlex 40 Adjustable Frequency AC Drive FRN 1.xx - 6.xx User Manual
Publication 22B-UM001H-EN-E
22B-UM001.book Page 5 Wednesday, January 22, 2014 11:04 AM
No. Fault
F100 Parameter
Checksum
F122 I/O Board Fail
(1)
Type(1)
Troubleshooting
➁
➁
Description
The checksum read from the
board does not match the
checksum calculated.
Failure has been detected in the
drive control and I/O section.
4-5
Action
Set P041 [Reset To Defalts] to
option 1 “Reset Defaults”.
1. Cycle power.
2. Replace drive if fault cannot be
cleared.
See page 4-1 for a description of fault types.
Common Symptoms and Corrective Actions
Motor does not Start.
Cause(s)
No output voltage to the motor.
Indication
None
Improper boost setting at initial
start-up.
Drive is Faulted
None
Flashing red status light
Corrective Action
Check the power circuit.
• Check the supply voltage.
• Check all fuses and disconnects.
Check the motor.
• Verify that the motor is
connected properly.
Check the control input signals.
• Verify that a Start signal is
present. If 2-Wire control is used,
verify that either the Run
Forward or Run Reverse signal
is active, but not both.
• Verify that I/O Terminal 01 is
active.
• Verify that P036 [Start Source]
matches your configuration.
• Verify that A095 [Reverse
Disable] is not prohibiting
movement.
Set A084 [Boost Select] to option 2
“35.0, VT”.
Clear fault.
• Press Stop
• Cycle power
• Set A100 [Fault Clear] to option 1
“Clear Faults”.
• Cycle digital input if A051 - A054
[Digital Inx Sel] is set to option 7
“Clear Fault”.
PowerFlex 40 Adjustable Frequency AC Drive FRN 1.xx - 6.xx User Manual
Publication 22B-UM001H-EN-E
22B-UM001.book Page 6 Wednesday, January 22, 2014 11:04 AM
4-6
Troubleshooting
Drive does not Start from Start or Run Inputs wired to the terminal block.
Cause(s)
Drive is Faulted
Indication
Flashing red status light
None
Incorrect programming.
• P036 [Start Source] is set to
option 0 “Keypad” or option 5
“RS485 (DSI) Port”.
• A051 - A054 [Digital Inx Sel] is
set to option 5 “Local” and the
input is active.
None
Incorrect input wiring.
See 1-18 for wiring examples.
• 2 wire control requires Run
Forward, Run Reverse or Jog
input.
• 3 wire control requires Start and
Stop inputs
• Stop input is always required.
Incorrect Sink/Source DIP switch
None
setting.
Corrective Action
Clear fault.
• Press Stop
• Cycle power
• Set A100 [Fault Clear] to option 1
“Clear Faults”.
• Cycle digital input if A051 - A054
[Digital Inx Sel] is set to option 7
“Clear Fault”.
Check parameter settings.
Wire inputs correctly and/or install
jumper.
Set switch to match wiring scheme.
Drive does not Start from Integral Keypad.
Cause(s)
Indication
Corrective Action
Integral keypad is not enabled. Green LED above Start key is • Set parameter P036 [Start
Source] to option 0 “Keypad”.
not illuminated.
• Set parameter A051 - A054
[Digital Inx Sel] to option 5
“Local” and activate the input.
I/O Terminal 01 “Stop” input is None
Wire inputs correctly and/or install
not present.
jumper.
PowerFlex 40 Adjustable Frequency AC Drive FRN 1.xx - 6.xx User Manual
Publication 22B-UM001H-EN-E
22B-UM001.book Page 7 Wednesday, January 22, 2014 11:04 AM
Troubleshooting
4-7
Drive does not respond to changes in speed command.
Cause(s)
No value is coming from the
source of the command.
Indication
The drive “Run” indicator is lit
and output is 0 Hz.
Incorrect reference source is
being selected via remote
device or digital inputs.
None
Corrective Action
• Check d012 [Control Source] for
correct source.
• If the source is an analog input,
check wiring and use a meter to
check for presence of signal.
• Check d002 [Commanded Freq]
to verify correct command.
• Check d012 [Control Source] for
correct source.
• Check d014 [Dig In Status] to
see if inputs are selecting an
alternate source. Verify settings
for A051 - A054 [Digital Inx Sel].
• Check P038 [Speed Reference]
for the source of the speed
reference. Reprogram as
necessary.
• Review the Speed Reference
Control chart on page 1-23.
Motor and/or drive will not accelerate to commanded speed.
Cause(s)
Indication
Acceleration time is excessive. None
Excess load or short
None
acceleration times force the
drive into current limit, slowing
or stopping acceleration.
Speed command source or
value is not as expected.
None
Programming is preventing the None
drive output from exceeding
limiting values.
Torque performance does not None
match motor characteristics.
Corrective Action
Reprogram P039 [Accel Time 1] or
A067 [Accel Time 2].
Compare d003 [Output Current] with
A089 [Current Limit 1].
Remove excess load or reprogram
P039 [Accel Time 1] or A067 [Accel
Time 2].
Check for improper A084 [Boost
Select] setting.
Verify d002 [Commanded Freq].
Check d012 [Control Source] for the
proper Speed Command.
Check P035 [Maximum Freq] to
insure that speed is not limited by
programming.
Set motor nameplate full load amps
in parameter A126 [Motor NP FLA].
Perform A127 [Autotune] “Static
Tune” or “Rotate Tune” procedure.
Set A125 [Torque Perf Mode] to
option 0 “V/Hz”.
PowerFlex 40 Adjustable Frequency AC Drive FRN 1.xx - 6.xx User Manual
Publication 22B-UM001H-EN-E
22B-UM001.book Page 8 Wednesday, January 22, 2014 11:04 AM
4-8
Troubleshooting
Motor operation is unstable.
Cause(s)
Motor data was incorrectly
entered.
Indication
None
Corrective Action
1. Correctly enter motor nameplate
data into P031, P032 and P033.
2. Enable A097 [Compensation].
3. Use A084 [Boost Select] to
reduce boost level.
Drive will not reverse motor direction.
Cause(s)
Indication
Digital input is not selected for None
reversing control.
Digital input is incorrectly
wired.
Motor wiring is improperly
phased for reverse.
Reverse is disabled.
None
Corrective Action
Check [Digital Inx Sel] (See
page 3-14). Choose correct input
and program for reversing mode.
Check input wiring. (See page 1-17)
None
Switch two motor leads.
None
Check A095 [Reverse Disable].
Drive does not power up.
Cause(s)
No input power to drive.
Indication
None
Jumper between I/O Terminals None
P2 and P1 not installed and/or
DC Bus Inductor not
connected.
Corrective Action
Check the power circuit.
• Check the supply voltage.
• Check all fuses and disconnects.
Install jumper or connect DC Bus
Inductor.
PowerFlex 40 Adjustable Frequency AC Drive FRN 1.xx - 6.xx User Manual
Publication 22B-UM001H-EN-E
22B-UM001.book Page 1 Wednesday, January 22, 2014 11:04 AM
Appendix A
Supplemental Drive Information
For information on…
Drive, Fuse & Circuit Breaker Ratings
Specifications
See page…
A-1
A-2
Drive, Fuse & Circuit Breaker Ratings
The tables on the following pages provide recommended AC line input
fuse and circuit breaker information. See Fusing and Circuit Breakers
below for UL and IEC requirements. Sizes listed are the recommended
sizes based on 40 °C (104 °F) and the U.S. N.E.C. Other country, state or
local codes may require different ratings.
Fusing
The recommended fuse types are listed below. If available current ratings
do not match those listed in the tables provided, choose the next higher
fuse rating.
• IEC – BS88 (British Standard) Parts 1 & 2 (1), EN60269-1, Parts 1 &
2, type gG or equivalent should be used.
• UL – UL Class CC, T or J must be used. (2)
Circuit Breakers
The “non-fuse” listings in the following tables include inverse time
circuit breakers, instantaneous trip circuit breakers (motor circuit
protectors) and 140M self-protected combination motor controllers. If
one of these is chosen as the desired protection method, the following
requirements apply:
•
IEC – Both types of circuit breakers and 140M self-protected
combination motor controllers are acceptable for IEC installations.
•
UL – Only inverse time circuit breakers and the specified 140M
self-protected combination motor controllers are acceptable for UL
installations.
(1)
Typical designations include, but may not be limited to the following; Parts 1 & 2: AC,
AD, BC, BD, CD, DD, ED, EFS, EF, FF, FG, GF, GG, GH.
(2)
Typical designations include; Type CC - KTK-R, FNQ-R
Type J - JKS, LPJ
Type T - JJS, JJN
PowerFlex 40 Adjustable Frequency AC Drive FRN 1.xx - 6.xx User Manual
Publication 22B-UM001H-EN-E
22B-UM001.book Page 2 Wednesday, January 22, 2014 11:04 AM
A-2
Supplemental Drive Information
Specifications
Drive Ratings
Catalog
Number(1)
Output Ratings
Input Ratings
Branch Circuit Protection
Min. Enclosure
140M Motor
Voltage
kW (HP) Amps Range kVA Amps Fuses Protectors(3) (4) Contactors Volume(5) (in.3)
100 - 120V AC (±10%) – 1-Phase Input, 0 - 230V 3-Phase Output
22B-V2P3x104
0.4 (0.5)
2.3
90-132
1.15 9.0
15
140M-C2E-C16
100-C12
1655
22B-V5P0x104
0.75 (1.0) 5.0
90-132
2.45 20.3
35
140M-D8E-C20
100-C23
1655
22B-V6P0x104
1.1 (1.5)
90-132
3.0
40
140M-F8E-C32
100-C37
1655
6.0
24.0
200 - 240V AC (±10%) – 1-Phase(2) Input, 0 - 230V 3-Phase Output
22B-A2P3x104
0.4 (0.5)
180-264 1.15 6.0
10
140M-C2E-B63
100-C09
1655
22B-A5P0x104
0.75 (1.0) 5.0
2.3
180-264 2.45 12.0
20
140M-C2E-C16
100-C12
1655
22B-A8P0x104
1.5 (2.0)
8.0
180-264 4.0
18.0
30
140M-D8E-C20
100-C23
1655
22B-A012x104
2.2 (3.0)
12.0
180-264 5.5
25.0
40
140M-F8E-C32
100-C37
2069
1655
200 - 240V AC (±10%) – 3-Phase Input, 0 - 230V 3-Phase Output
22B-B2P3x104
0.4 (0.5)
2.3
180-264 1.15 2.5
6
140M-C2E-B40
100-C07
22B-B5P0x104
0.75 (1.0) 5.0
180-264 2.45 5.7
10
140M-C2E-C10
100-C09
1655
22B-B8P0x104
1.5 (2.0)
180-264 4.0
15
140M-C2E-C16
100-C12
1655
8.0
9.5
22B-B012x104
2.2 (3.0)
12.0
180-264 5.5
15.5
25
140M-C2E-C16
100-C23
1655
22B-B017x104
3.7 (5.0)
17.5
180-264 8.6
21.0
30
140M-F8E-C25
100-C23
1655
22B-B024x104
5.5 (7.5)
24.0
180-264 11.8 26.1
40
140M-F8E-C32
100-C37
2069
22B-B033x104
7.5 (10.0) 33.0
180-264 16.3 34.6
60
140M-G8E-C45
100-C60
2069
1655
380 - 480V AC (±10%) – 3-Phase Input, 0 - 460V 3-Phase Output
22B-D1P4x104
0.4 (0.5)
1.4
342-528 1.4
1.8
3
140M-C2E-B25
100-C07
22B-D2P3x104
0.75 (1.0) 2.3
342-528 2.3
3.2
6
140M-C2E-B40
100-C07
1655
22B-D4P0x104
1.5 (2.0)
4.0
342-528 4.0
5.7
10
140M-C2E-B63
100-C09
1655
22B-D6P0x104
2.2 (3.0)
6.0
342-528 5.9
7.5
15
140M-C2E-C10
100-C09
1655
22B-D010x104
4.0 (5.0)
10.5
342-528 10.3 13.0
20
140M-C2E-C16
100-C23
1655
22B-D012x104
5.5 (7.5)
12.0
342-528 11.8 14.2
25
140M-D8E-C20
100-C23
2069
22B-D017x104
7.5 (10.0) 17.0
342-528 16.8 18.4
30
140M-D8E-C20
100-C23
2069
22B-D024x104
11.0 (15.0) 24.0
342-528 23.4 26.0
50
140M-F8E-C32
100-C43
2069
460 - 600V AC (±10%) – 3-Phase Input, 0 - 575V 3-Phase Output
22B-E1P7x104
0.75 (1.0) 1.7
414-660 2.1
2.3
6
140M-C2E-B25
100-C09
1655
22B-E3P0x104
1.5 (2.0)
3.0
414-660 3.65 3.8
6
140M-C2E-B40
100-C09
1655
22B-E4P2x104
2.2 (3.0)
4.2
414-660 5.2
5.3
10
140M-D8E-B63
100-C09
1655
22B-E6P6x104
4.0 (5.0)
6.6
414-660 8.1
8.3
15
140M-D8E-C10
100-C09
1655
22B-E9P9x104
5.5 (7.5)
9.9
414-660 12.1 11.2
20
140M-D8E-C16
100-C16
2069
22B-E012x104
7.5 (10.0) 12.2
414-660 14.9 13.7
25
140M-D8E-C16
100-C23
2069
22B-E019x104
11.0 (15.0) 19.0
414-660 23.1 24.1
40
140M-F8E-C25
100-C30
2069
(1)
(2)
(3)
In the Catalog Numbers listed “x” represents enclosure type. Specifications are valid for all
enclosure types. IP66, NEMA/UL Type 4X drive ratings are only available as Frame B drives. Refer
to Table B.B.
200-240V AC - 1-Phase drives are also available with an integral EMC filter. Catalog suffix
changes from N104 to N114. Filter option is not available for IP66, NEMA/UL Type 4X rated drives.
The AIC ratings of the Bulletin 140M Motor Protector Circuit Breakers may vary. See Bulletin 140M
Motor Protection Circuit Breakers Application Ratings.
PowerFlex 40 Adjustable Frequency AC Drive FRN 1.xx - 6.xx User Manual
Publication 22B-UM001H-EN-E
22B-UM001.book Page 3 Wednesday, January 22, 2014 11:04 AM
Supplemental Drive Information
(4)
(5)
A-3
Manual Self-Protected (Type E) Combination Motor Controller, UL listed for 208 Wye or Delta, 240
Wye or Delta, 480Y/277 or 600Y/347. Not UL listed for use on 480V or 600V Delta/Delta, corner
ground, or high-resistance ground systems.
When using a Manual Self-Protected (Type E) Combination Motor Controller, the drive must be
installed in a ventilated or non-ventilated enclosure with the minimum volume specified in this
column. Application specific thermal considerations may require a larger enclosure.
Approvals
Input/Output Ratings
Digital Control Inputs (Input Current = 6mA)
SRC (Source) Mode:
18-24V = ON
0-6V = OFF
SNK (Sink) Mode:
0-6V = ON
18-24V = OFF
LIS
TED 966X
UL
Output Frequency: 0-400 Hz (Programmable)
Efficiency: 97.5% (Typical)
®
I ND
LIS
UL508C
C
TED 966X
UL
®
I ND
CO N T EQ
CSA 22.2
CO N T EQ
EMC Directive 89/336
LV:
EN 50178, EN 60204
EMC: EN 61800-3, EN 50081-1, EN 50082-2
Analog Control Inputs
4-20mA Analog: 250 ohm input impedance
0-10V DC Analog: 100k ohm input impedance
External Pot: 1-10k ohms, 2 Watt minimum
Control Output
Programmable Output (form C relay)
Resistive Rating: 3.0A at 30V DC, 3.0A at 125V AC, 3.0A at 240V AC
Inductive Rating: 0.5A at 30V DC, 0.5A at 125V AC, 0.5A at 240V AC
Opto Outputs
30V DC, 50mA
Non-inductive
Analog Outputs (10 bit)
0-10V, 1k ohm Min.
4-20mA, 525 ohm Max.
Fuses and Circuit Breakers
Recommended Fuse Type: UL Class J, CC, T or Type BS88; 600V (550V) or equivalent.
Recommended Circuit Breakers: HMCP circuit breakers or equivalent.
Protective Features
Motor Protection: I2t overload protection - 150% for 60 Secs, 200% for 3 Secs (Provides Class 10 protection)
Overcurrent: 200% hardware limit, 300% instantaneous fault
Over Voltage:
100-120V AC Input – Trip occurs at 405V DC bus voltage (equivalent to 150V AC incoming line)
200-240V AC Input – Trip occurs at 405V DC bus voltage (equivalent to 290V AC incoming line)
380-460V AC Input – Trip occurs at 810V DC bus voltage (equivalent to 575V AC incoming line)
460-600V AC Input – Trip occurs at 1005V DC bus voltage (equivalent to 711V AC incoming line)
Under Voltage: 100-120V AC Input – Trip occurs at 210V DC bus voltage (equivalent to 75V AC incoming line)
200-240V AC Input – Trip occurs at 210V DC bus voltage (equivalent to 150V AC incoming line)
380-480V AC Input – Trip occurs at 390V DC bus voltage (equivalent to 275V AC incoming line)
460-600V AC Input – If P042 = 3 “High Voltage” trip occurs at 487V DC bus voltage (344V AC incoming line);
If P042 = 2 “Low Voltage” trip occurs at 390V DC bus voltage (275V AC incoming line)
Control Ride Through: Minimum ride through is 0.5 Secs - typical value 2 Secs
Faultless Power Ride Through: 100 milliseconds
Dynamic Braking
Internal brake IGBT included with all ratings except when no brake is specified.
Refer to Appendix B for DB resistor ordering information.
PowerFlex 40 Adjustable Frequency AC Drive FRN 1.xx - 6.xx User Manual
Publication 22B-UM001H-EN-E
22B-UM001.book Page 4 Wednesday, January 22, 2014 11:04 AM
A-4
Supplemental Drive Information
Category
Environment
Specification
Altitude:
Maximum Surrounding Air
Temperature without derating:
IP20, NEMA/UL Type Open:
IP30, NEMA/UL Type 1:
Flange Mount:
IP66, NEMA/UL Type 4X:
Cooling Method
Convection:
Fan:
Storage Temperature:
Atmosphere:
Control
Relative Humidity:
Shock (operating):
Vibration (operating):
Carrier Frequency
Frequency Accuracy
Digital Input:
Analog Input:
Analog Output:
Speed Regulation - Open Loop
with Slip Compensation:
Stop Modes:
Accel/Decel:
Intermittent Overload:
Electronic Motor Overload
Protection:
Electrical
Voltage Tolerance:
Frequency Tolerance:
Input Phases:
Displacement Power Factor:
Maximum Short Circuit Rating:
Actual Short Circuit Rating:
Transistor Type:
1000 m (3300 ft) max. without derating
–10 to 50° C (14 to 122° F)
–10 to 40° C (14 to 104° F)
Heatsink: –10 to 40° C (14 to 104° F)
Drive:
–10 to 50° C (14 to 122° F)
–10 to 40° C (14 to 104° F)
0.4 kW (0.5 HP) drives
All other drive ratings and 0.4 kW (0.5 HP)
1-Phase drives with Integral “S Type” EMC Filter
–40 to 85 degrees C (–40 to 185 degrees F)
Important: Drive must not be installed in an
area where the ambient atmosphere contains
volatile or corrosive gas, vapors or dust. If the
drive is not going to be installed for a period of
time, it must be stored in an area where it will not
be exposed to a corrosive atmosphere.
0 to 95% non-condensing
15G peak for 11ms duration (±1.0ms)
1G peak, 5 to 2000 Hz
2-16 kHz. Drive rating based on 4 kHz.
Within ±0.05% of set output frequency.
Within 0.5% of maximum output frequency,
10-Bit resolution
±2% of full scale, 10-Bit resolution
±1% of base speed across a 60:1 speed range.
Multiple programmable stop modes including Ramp, Coast, DC-Brake, Ramp-to-Hold and
S Curve.
Two independently programmable accel and
decel times. Each time may be programmed from
0 - 600 seconds in 0.1 second increments.
150% Overload capability for up to 1 minute
200% Overload capability for up to 3 seconds
Provides class 10 motor overload protection
according to NEC article 430 and motor
over-temperature protection according to NEC
article 430.126 (A) (2). UL 508C File 29572.
100-120V ±10%
200-240V ±10%
380-480V ±10%
460-600V ±10%
48-63 Hz
Three-phase input provides full rating. Single-phase
operation provides 35% rated current.
0.98 across entire speed range
100,000 Amps Symmetrical
Determined by AIC Rating of installed fuse/circuit
breaker
Insulated Gate Bipolar Transistor (IGBT)
PowerFlex 40 Adjustable Frequency AC Drive FRN 1.xx - 6.xx User Manual
Publication 22B-UM001H-EN-E
22B-UM001.book Page 5 Wednesday, January 22, 2014 11:04 AM
Supplemental Drive Information
A-5
PowerFlex 40 Estimated Watts Loss (Rated Load, Speed & PWM)
Voltage
100–120V
200–240V
380–480V
460–600V
kW (HP)
0.4 (0.5)
0.75 (1.0)
1.1 (1.5)
0.4 (0.5)
0.75 (1.0)
1.1 (2.0)
2.2 (3.0)
3.7 (5.0)
5.5 (7.5)
7.5 (10)
0.4 (0.5)
0.75 (1.0)
1.1 (2.0)
2.2 (3.0)
3.7 (5.0)
5.5 (7.5)
7.5 (10)
11 (15)
0.75 (1.0)
1.5 (2.0)
2.2 (3.0)
4.0 (5.0)
5.5 (7.5)
7.5 (10)
11 (15)
External Watts
22
40
58
22
40
63
100
150
200
265
17
30
48
75
135
140
175
260
30
48
75
135
140
175
260
Internal Watts
18
20
22
18
20
22
25
30
35
40
18
20
22
25
25
35
35
40
20
22
25
25
35
35
40
Total Watts Loss
40
60
80
40
60
85
125
180
235
305
35
50
70
100
160
175
210
300
50
70
100
160
175
210
300
PowerFlex 40 Adjustable Frequency AC Drive FRN 1.xx - 6.xx User Manual
Publication 22B-UM001H-EN-E
22B-UM001.book Page 6 Wednesday, January 22, 2014 11:04 AM
A-6
Supplemental Drive Information
Notes:
PowerFlex 40 Adjustable Frequency AC Drive FRN 1.xx - 6.xx User Manual
Publication 22B-UM001H-EN-E
22B-UM001.book Page 1 Wednesday, January 22, 2014 11:04 AM
Appendix B
Accessories and Dimensions
Product Selection
Table B.A Catalog Number Description
22B Drive
A
1P5
N
1
1
4
Voltage Rating
Rating
Enclosure
HIM
Emission Class
Type
Table B.B PowerFlex 40 Drives
IP20 Flange
IP20, NEMA/UL Type Open Mount(1)
Drive Ratings
IP66, NEMA/UL
Type 4X
Input Voltage
kW
HP
Output
Current Catalog Number
Frame
Size
Catalog Number
Catalog Number
120V 50/60 Hz
1-Phase
No Filter
0.4
0.5
2.3A
22B-V2P3N104
B
22B-V2P3F104
22B-V2P3C104
0.75
1.0
5.0A
22B-V5P0N104
B
22B-V5P0F104
22B-V5P0C104
1.1
1.5
6.0A
22B-V6P0N104
B
22B-V6P0F104
22B-V6P0C104
240V 50/60 Hz
1-Phase
With Integral “S
Type” EMC
Filter
0.4
0.5
2.3A
22B-A2P3N114
B
–
–
0.75
1.0
5.0A
22B-A5P0N114
B
–
–
1.5
2.0
8.0A
22B-A8P0N114
B
–
–
2.2
3.0
12.0A
22B-A012N114
C
–
–
240V 50/60 Hz
1-Phase
No Filter
0.4
0.5
2.3A
22B-A2P3N104
B
22B-A2P3F104
22B-A2P3C104
0.75
1.0
5.0A
22B-A5P0N104
B
22B-A5P0F104
22B-A5P0C104
1.5
2.0
8.0A
22B-A8P0N104
B
22B-A8P0F104
22B-A8P0C104
2.2
3.0
12.0A
22B-A012N104
C
22B-A012F104
–
0.4
0.5
2.3A
22B-B2P3N104
B
22B-B2P3F104
22B-B2P3C104
240V 50/60 Hz
3-Phase
No Filter
480V 50/60 Hz
3-Phase
No Filter
600V 50/60 Hz
3-Phase
No Filter
(1)
(2)
0.75
1.0
5.0A
22B-B5P0N104
B
22B-B5P0F104
22B-B5P0C104
1.5
2.0
8.0A
22B-B8P0N104
B
22B-B8P0F104
22B-B8P0C104
2.2
3.0
12.0A
22B-B012N104
B
22B-B012F104
22B-B012C104
3.7
5.0
17.5A
22B-B017N104
B
22B-B017F104
22B-B017C104
5.5
7.5
24.0A
22B-B024N104
C
22B-B024F104
–
7.5
10.0
33.0A
22B-B033N104
C
22B-B033F104
–
0.4
0.5
1.4A
22B-D1P4N104
B
22B-D1P4F104
22B-D1P4C104
0.75
1.0
2.3A
22B-D2P3N104
B
22B-D2P3F104
22B-D2P3C104
1.5
2.0
4.0A
22B-D4P0N104
B
22B-D4P0F104
22B-D4P0C104
2.2
3.0
6.0A
22B-D6P0N104
B
22B-D6P0F104
22B-D6P0C104
4.0
5.0
10.5A
22B-D010N104
B
22B-D010F104
22B-D010C104
5.5
7.5
12.0A
22B-D012N104
C
22B-D012F104
–
7.5
10.0
17.0A
22B-D017N104
C
22B-D017F104
11.0
0.75
15.0
1.0
24.0A
1.7A
22B-D024N104
22B-E1P7N104
C
B
–
22B-D024F104 (2) –
22B-E1P7F104
22B-E1P7C104
1.5
2.0
3.0A
22B-E3P0N104
B
22B-E3P0F104
22B-E3P0C104
2.2
3.0
4.2A
22B-E4P2N104
B
22B-E4P2F104
22B-E4P2C104
4.0
5.0
6.6A
22B-E6P6N104
B
22B-E6P6F104
22B-E6P6C104
5.5
7.5
9.9A
22B-E9P9N104
C
22B-E9P9F104
–
7.5
10.0
12.0A
22B-E012N104
C
22B-E012F104
–
11.0
15.0
19.0A
22B-E019N104
C
22B-E019F104
–
Meets IP40/54/65 (NEMA 1/12/4/4X) when installed in an enclosure of like rating.
Requires use of external DC Bus Inductor or AC Line Reactor. See Table B.E for details.
PowerFlex 40 Adjustable Frequency AC Drive FRN 1.xx - 6.xx User Manual
Publication 22B-UM001H-EN-E
22B-UM001.book Page 2 Wednesday, January 22, 2014 11:04 AM
B-2
Accessories and Dimensions
Table B.C Dynamic Brake Modules
Drive Ratings
Input Voltage
kW
HP
Minimum
Resistance Ω
Catalog Number (1) (2)
120V 50/60 Hz
1-Phase
0.4
0.5
48
AK-R2-091P500
0.75
1.0
48
AK-R2-091P500
1.1
1.5
48
AK-R2-091P500
0.4
0.5
48
AK-R2-091P500
0.75
1.0
48
AK-R2-091P500
1.5
2.0
48
AK-R2-091P500
2.2
3.0
32
AK-R2-047P500
0.4
0.5
48
AK-R2-091P500
0.75
1.0
48
AK-R2-091P500
1.5
2.0
48
AK-R2-091P500
2.2
3.0
32
AK-R2-047P500
3.7
5.0
19
AK-R2-047P500
5.5
7.5
13
AK-R2-030P1K2
7.5
10.0
10
AK-R2-030P1K2
0.4
0.5
97
AK-R2-360P500
0.75
1.0
97
AK-R2-360P500
1.5
2.0
97
AK-R2-360P500
2.2
3.0
97
AK-R2-120P1K2
4.0
5.0
77
AK-R2-120P1K2
5.5
7.5
55
AK-R2-120P1K2
7.5
10.0
39
AK-R2-120P1K2
11.0
0.75
15.0
1.0
24
120
AK-R2-120P1K2 (3)
AK-R2-360P500
240V 50/60 Hz
1-Phase
240V 50/60 Hz
3-Phase
480V 50/60 Hz
3-Phase
600V 50/60 Hz
3-Phase
(1)
(2)
(3)
1.5
2.0
120
AK-R2-360P500
2.2
3.0
82
AK-R2-120P1K2
4.0
5.0
82
AK-R2-120P1K2
5.5
7.5
51
AK-R2-120P1K2
7.5
10.0
51
AK-R2-120P1K2
11.0
15.0
51
AK-R2-120P1K2 (3)
The resistors listed in this tables are rated for 5% duty cycle.
Use of Rockwell resistors is always recommended. The resistors listed have been carefully
selected for optimizing performance in a variety of applications. Alternative resistors may be used,
however care must be taken when making a selection. Refer to the PowerFlex Dynamic Braking
Resistor Calculator, publication PFLEX-AT001.
Requires two resistors wired in parallel.
PowerFlex 40 Adjustable Frequency AC Drive FRN 1.xx - 6.xx User Manual
Publication 22B-UM001H-EN-E
22B-UM001.book Page 3 Wednesday, January 22, 2014 11:04 AM
Accessories and Dimensions
B-3
Table B.D Bulletin 1321-3R Series Line Reactors
Input Voltage
kW
HP
240V 50/60 Hz 0.4 0.5
3-Phase
0.75 1.0
Maximum
Fundamental Continuous Inductance Watts
Amps
Amps
mh
Loss
4
6
12.0
21 W
1321-3R4-D
8
12
3.0
29 W
1321-3R8-B
1.5
2.0
8
12
1.5
19.5 W
1321-3R8-A
2.2
3.0
12
18
1.25
26 W
1321-3R12-A
3.7
5.0
18
27
0.8
36 W
1321-3R18-A
5.5
7.5
25
37.5
0.5
48 W
1321-3R25-A
7.5
10.0 35
52.5
0.4
49 W
1321-3R35-A
3
20.0
11.3 W
1321-3R2-B
1321-3R4-C
480V 50/60 Hz 0.4 0.5
3-Phase
0.75 1.0
2
4
6
9.0
20 W
1.5
2.0
4
6
6.5
20 W
1321-3R4-B
2.2
3.0
8
12
5.0
25.3 W
1321-3R8-C
4.0
5.0
12
18
2.5
31 W
1321-3R12-B
5.5
7.5
12
18
2.5
31 W
1321-3R12-B
7.5
10.0 18
27
1.5
43 W
1321-3R18-B
11.0 15.0 25
600V 50/60 Hz 0.75 1.0
3-Phase
1.5 2.0
(1)
Catalog
Number (1)
37.5
1.2
52 W
1321-3R25-B
2
3
20.0
11.3 W
1321-3R2-B
4
6
6.5
20 W
1321-3R4-B
2.2
3.0
4
6
6.5
20 W
1321-3R4-B
4.0
5.0
8
12
5.0
25.3 W
1321-3R8-C
5.5
7.5
12
18
2.5
31 W
1321-3R12-B
7.5
10.0 12
18
2.5
31 W
1321-3R12-B
11.0 15.0 18
27
1.5
43 W
1321-3R18-B
Catalog numbers listed are for 3% impedance open style units. NEMA Type 1 and 5% impedance
reactor types are also available. Refer to publication 1321-TD001….
Table B.E DC Bus Inductors
Input Voltage
kW
HP
Amps
Inductance
mh
240V 50/60 Hz
3-Phase
5.5
7.5
32
0.85
32RB001
7.5
10.0
40
0.5
40RB001
480V 50/60 Hz
3-Phase
5.5
7.5
18
3.75
18RB004
7.5
10.0
25
4.0
25RB005
11.0
15.0
32
2.68
32RB003
5.5
7.5
12
6.0
12RB004
600V 50/60 Hz
3-Phase
(2)
MTE Catalog Number (2)
7.5
10.0
18
6.0
18RB005
11.0
15.0
25
4.0
25RB005
Use MTE RB Series or equivalent inductors.
PowerFlex 40 Adjustable Frequency AC Drive FRN 1.xx - 6.xx User Manual
Publication 22B-UM001H-EN-E
22B-UM001.book Page 4 Wednesday, January 22, 2014 11:04 AM
B-4
Accessories and Dimensions
Table B.F EMC Line Filters
Drive Ratings
S Type Filter
Catalog Number (1)
L Type Filter
Catalog Number (4)
0.5
–
22-RF018-BL
1.0
–
22-RF018-BL
1.5
–
22-RF018-BL
0.4
0.5
(2)
22-RF018-BL
0.75
1.0
(2)
22-RF018-BL
1.5
2.0
(2)
22-RF018-BL
2.2
3.0
(2)
22-RF025-CL
0.4
0.5
22-RF021-BS(3)
22-RF021-BL
0.75
1.0
22-RF021-BS(3)
22-RF021-BL
1.5
2.0
22-RF021-BS(3)
22-RF021-BL
2.2
3.0
22-RF021-BS(3)
22-RF021-BL
3.7
5.0
22-RF021-BS(3)
22-RF021-BL
5.5
7.5
22-RF034-CS
22-RF034-CL
7.5
10.0
22-RF034-CS
22-RF034-CL
0.4
0.5
22-RF012-BS
22-RF012-BL
Input Voltage
kW
120V 50/60 Hz
1-Phase
0.4
0.75
1.1
240V 50/60 Hz
1-Phase
240V 50/60 Hz
3-Phase
480V 50/60 Hz
3-Phase
600V 50/60 Hz
3-Phase
(1)
(2)
(3)
(4)
HP
0.75
1.0
22-RF012-BS
22-RF012-BL
1.5
2.0
22-RF012-BS
22-RF012-BL
2.2
3.0
22-RF012-BS
22-RF012-BL
4.0
5.0
22-RF012-BS
22-RF012-BL
5.5
7.5
22-RF018-CS
22-RF018-CL
7.5
10.0
22-RF018-CS
22-RF018-CL
11.0
15.0
22-RF026-CS
22-RF026-CL
0.75
1.0
–
22-RF8P0-BL
1.5
2.0
–
22-RF8P0-BL
2.2
3.0
–
22-RF8P0-BL
4.0
5.0
–
22-RF8P0-BL
5.5
7.5
–
22-RF015-CL
7.5
10.0
–
22-RF015-CL
11.0
15.0
–
22-RF024-CL
This filter is suitable for use with a cable length of at least 10 meters (33 feet) for Class A and 1
meter for Class B environments.
These ratings can be ordered with internal “S Type” filters. Refer to the Catalog Number
explanation on page P-4 and Table B.B for details.
Filter must be Series B or later.
This filter is suitable for use with a cable length of at least 100 meters for Class A and 5 meters for
Class B environments.
PowerFlex 40 Adjustable Frequency AC Drive FRN 1.xx - 6.xx User Manual
Publication 22B-UM001H-EN-E
22B-UM001.book Page 5 Wednesday, January 22, 2014 11:04 AM
Accessories and Dimensions
B-5
Table B.G Human Interface Module (HIM) Option Kits and Accessories
Item
Description
Catalog Number
LCD Display, Remote Panel
Mount
Digital speed control
CopyCat capable
IP66 (NEMA Type 4X/12) indoor use only
Includes 2.9 meter cable
22-HIM-C2S
LCD Display, Remote Panel
Mount
Digital speed control
CopyCat capable
IP66 (NEMA Type 4X/12) indoor use only
Includes 2.9 meter cable
22-HIM-C2
LCD Display, Remote Handheld Digital speed control
Full numeric keypad
CopyCat capable
IP30 (NEMA Type 1)
Includes 1.0 meter cable
Panel mount with optional Bezel Kit
22-HIM-A3
Bezel Kit
Panel mount for LCD Display, Remote
Handheld unit, IP30 (NEMA Type 1)
22-HIM-B1
DSI HIM Cable
(DSI HIM to RJ45 cable)
1.0 Meter (3.3 Feet)
2.9 Meter (9.51 Feet)
22-HIM-H10
22-HIM-H30
Table B.H IP30/NEMA 1/UL Type 1 Kit
Item
Description
Drive
Frame Catalog Number
IP30/NEMA 1/UL Type 1 Field installed kit. Converts drive to IP30/
Kit
NEMA 1/UL Type 1 enclosure. Includes
conduit box with mounting screws and
plastic top panel.
B
22-JBAB
C
22-JBAC
IP30/NEMA 1/UL Type 1 Field installed kit. Converts drive to IP30/
Kit for Communication
NEMA 1/UL Type 1 enclosure. Includes
Option
communication option conduit box with
mounting screws and plastic top panel.
B
22-JBCB
C
22-JBCC
PowerFlex 40 Adjustable Frequency AC Drive FRN 1.xx - 6.xx User Manual
Publication 22B-UM001H-EN-E
22B-UM001.book Page 6 Wednesday, January 22, 2014 11:04 AM
B-6
Accessories and Dimensions
Table B.I Communication Option Kits and Accessories
Item
Description
Catalog Number
Communication
Adapters
Embedded communication options for use with
the PowerFlex 4-Class drives.
Requires a Communication Adapter Cover (IP20,
NEMA/UL Type 1 only. Ordered Separately)
BACnet®
ControlNet™
DeviceNet™
EtherNet/IP™
LonWorks®
PROFIBUS™ DP
22-COMM-B
22-COMM-C
22-COMM-D
22-COMM-E
22-COMM-L
22-COMM-P
External DSI™
Communications Kit
External mounting kit for 22-COMM
communication options
22-XCOMM-DC-BASE
External Comms Power
Supply
Optional 100-240V AC Power Supply for External 20-XCOMM-AC-PS1
DSI Communications Kit.
Compact I/O Module
Three channel.
1769-SM2
Communication Adapter Cover that houses the DeviceNet Communication
Cover
Adapter (IP20, NEMA/UL Type 1 only)
B Frame Drive
22B-CCB
C Frame Drive
22B-CCC
Serial Converter Module Provides serial communication via DF1 protocol
(RS485 to RS232)
for use with DriveExplorer and DriveExecutive
software. Includes:
DSI to RS232 serial converter (1)
1203-SFC serial cable (1)
22-RJ45CBL-C20 cable (1)
DriveExplorer Lite CD (1)
22-SCM-232
DSI Cable
2.0 meter RJ45 to RJ45 cable, male to male
connectors.
22-RJ45CBL-C20
Serial Cable
2.0 meter serial cable with a locking low profile
1203-SFC
connector to connect to the serial converter and a
9-pin sub-miniature D female connector to
connect to a computer.
Null Cable Converter
For use when connecting the serial converter to
DriveExplorer on a handheld PC.
1203-SNM
Splitter Cable
RJ45 one to two port splitter cable
AK-U0-RJ45-SC1
Terminating Resistors
RJ45 120 Ohm resistors (2 pieces)
AK-U0-RJ45-TR1
Terminal Block
RJ45 Two position terminal block (5 pieces)
AK-U0-RJ45-TB2P
DriveExplorer Software Windows based software package that provides 9306-4EXP01ENE
(CD-ROM) Version 3.01 an intuitive means for monitoring or configuring
or later
Allen-Bradley drives and communication adapters
online.
Compatibility:
Windows 95, 98, ME, NT 4.0 (Service Pack 3 or
later), 2000, XP and CE(1)
DriveExecutive software Windows based software package that provides 9303-4DTE01ENE
(CD-ROM) Version 1.01 an intuitive means for monitoring or configuring
or later
Allen-Bradley drives and communication adapters
online and offline.
Compatibility:
Windows 98, ME, NT 4.0 (Service Pack 3 or
later), 2000 and XP
(1)
See www.ab.com/drives/driveexplorer.htm for supported devices.
PowerFlex 40 Adjustable Frequency AC Drive FRN 1.xx - 6.xx User Manual
Publication 22B-UM001H-EN-E
22B-UM001.book Page 7 Wednesday, January 22, 2014 11:04 AM
Accessories and Dimensions
B-7
Product Dimensions
Table B.J PowerFlex 40 Frames – Ratings are in kW and (HP)
Frame
B
120V AC –
1-Phase
240V AC –
1-Phase
240V AC –
3-Phase
0.4 (0.5)
0.75 (1.0)
1.1 (1.5)
0.4 (0.5)
0.75 (1.0)
1.5 (2.0)
2.2 (3.0)
0.4 (0.5)
0.75 (1.0)
1.5 (2.0)
5.5 (7.5)
7.5 (10.0)
C(1)
2.2 (3.0)
3.7 (5.0)
0.4 (0.5)
0.75 (1.0)
1.5 (2.0)
5.5 (7.5)
7.5 (10.0)
600V AC –
3-Phase
2.2 (3.0)
4.0 (5.0)
0.75 (1.0)
1.5 (2.0)
11.0 (15.0) 5.5 (7.5)
7.5 (10.0)
2.2 (3.0)
4.0 (5.0)
11.0 (15.0)
IP66, NEMA/UL Type 4X rated drives are not availble in Frame C drive ratings.
Figure B.1 IP20, NEMA/UL Type Open
A
Dimensions are in millimeters and (inches).
Weights are in kilograms and (pounds).
C
D
F
E
Frame
(1)
480V AC –
3-Phase
B
B
C
A
B
C
D
E
F
100
(3.94)
130
(5.1)
180
(7.09)
260
(10.2)
136
(5.35)
180
(7.1)
87
(3.43)
116
(4.57)
168
87.4
(6.61) (3.44)
246
–
(9.7)
Ship
Weight
2.2
(4.9)
4.3
(9.5)
5.5 (0.22)
Figure B.2 IP30, NEMA/UL Type 1 Option Kit without Communication Option
79.1 (3.11)
64.1 (2.52)
40.6 (1.60)
25.6 (1.01)
∅ 22.2
(0.87)
109.9
(4.33)
74.3
(2.93)
33.0
(1.30)
Frame B - 22-JBAB
107.0 (4.21)
66.0 (2.60)
24.0 (0.94)
∅ 28.5
(1.12)
∅ 22.2
(0.87)
152.2
(5.99)
111.2
(4.38)
60.0
(2.36)
Frame C - 22-JBAC
PowerFlex 40 Adjustable Frequency AC Drive FRN 1.xx - 6.xx User Manual
Publication 22B-UM001H-EN-E
22B-UM001.book Page 8 Wednesday, January 22, 2014 11:04 AM
B-8
Accessories and Dimensions
Figure B.3 IP30, NEMA/UL Type 1 Option Kit with Communication Option –
Dimensions are in millimeters and (inches)
25.0
(0.98)
77.5 (3.05)
50.0 (1.97)
22.5 (0.89)
∅ 22.2
(0.87)
134.3
(5.29)
105.3
(4.15)
76.3
(3.00)
64.0
(2.52)
Frame B - 22-JBCB
25.0
(0.98)
108.7 (4.28)
92.2 (3.63)
69.2 (2.72)
45.7 (1.80)
22.2 (0.87)
∅ 28.5
(1.12)
∅ 22.2
(0.87)
179.8
(7.08)
144.8
(5.70)
109.8
(4.32)
60.0
(2.36)
Frame C - 22-JBCC
PowerFlex 40 Adjustable Frequency AC Drive FRN 1.xx - 6.xx User Manual
Publication 22B-UM001H-EN-E
22B-UM001.book Page 9 Wednesday, January 22, 2014 11:04 AM
Accessories and Dimensions
B-9
Figure B.4 PowerFlex 40 Flange Mount Drives – Dimensions are in millimeters and
(inches)
244
(9.61)
94.3
(3.71)
214
(8.43)
63.1
(2.48)
250
(9.84)
Frame B
130.3
(5.13)
300
(11.81)
105.8
(4.17)
138.2
(5.44)
325
(12.8)
22B-CCC
Frame C
PowerFlex 40 Adjustable Frequency AC Drive FRN 1.xx - 6.xx User Manual
Publication 22B-UM001H-EN-E
22B-UM001.book Page 10 Wednesday, January 22, 2014 11:04 AM
B-10
Accessories and Dimensions
Figure B.5 PowerFlex 40 Flange Mount Cutout Dimensions – Dimensions are in
millimeters and (inches)
145
(5.71)
6.5
(0.26)
23.5
(0.93)
197
(7.76)
210
(8.27)
225
(8.86)
98.5
(3.88)
5.3
(0.21)
14
(0.55)
31
(1.22)
49
(1.93)
98
(3.86)
7.5
(0.30)
160
(6.30)
Frame B
5.3
(0.21)
164
(6.46)
8
(0.31)
307.5
(12.11)
230.6
(9.08)
291.5
(11.48)
153.8
(6.06)
76.9
(3.03)
90
(3.54)
180
(7.09)
Frame C
PowerFlex 40 Adjustable Frequency AC Drive FRN 1.xx - 6.xx User Manual
Publication 22B-UM001H-EN-E
8
(0.31)
22B-UM001.book Page 11 Wednesday, January 22, 2014 11:04 AM
Accessories and Dimensions
B-11
Figure B.6 PowerFlex 40 Replacement Plate Drive Dimensions – Dimensions are in
millimeters and (inches)
112
(4.41)
125
(4.92)
80
(3.15)
88
(3.46)
9.5
(0.37)
192
(7.56)
180
(7.09)
204
(8.03)
96
(3.78)
5.3
(0.21)
100
(3.94)
Frame B
142
(5.59)
155
(6.10)
123.5
(4.86)
80
(3.15)
98.5
(3.88)
9.5
(0.37)
272
(10.71)
284
(11.18)
260
(10.24)
136
(5.35)
130
(5.12)
5.3
(0.21)
22B-CCC
Frame C
PowerFlex 40 Adjustable Frequency AC Drive FRN 1.xx - 6.xx User Manual
Publication 22B-UM001H-EN-E
22B-UM001.book Page 12 Wednesday, January 22, 2014 11:04 AM
B-12
Accessories and Dimensions
Figure B.7 IP66, NEMA Type/UL Type 4X – Dimensions are in millimeters and (inches)
Weights are in kilograms and (pounds).
165
(6.50)
146
(5.75)
6.5
(0.26)
46
(1.81)
23
(0.91)
270
(10.63)
198
(7.80)
253
(9.96)
28
(1.10)
124
(4.88)
89
(3.50)
22
(0.87)
82.5
(3.25)
Weight
5.2 (11.5)
PowerFlex 40 Adjustable Frequency AC Drive FRN 1.xx - 6.xx User Manual
Publication 22B-UM001H-EN-E
22B-UM001.book Page 13 Wednesday, January 22, 2014 11:04 AM
Accessories and Dimensions
B-13
Figure B.8 Dynamic Brake Modules – Dimensions are in millimeters and (inches).
Weights are in kilograms and (pounds).
Frame A
Frame B
30.0
(1.18) 60.0
(2.36)
31.0
(1.22)
59.0
(2.32)
C
US
C
US
17.0
(0.67)
61.0
(2.40)
335.0
(13.19)
386.0
(15.20)
405.0
(15.94)
AUTOMATION
ROCKWELL
316.0
(12.44)
ROCKWELL
AUTOMATION
SURFACES MAY BE
13.0
(0.51)
Frame
Catalog Number
Weight
A
AK-R2-091P500, AK-R2-047P500, AK-R2-360P500
1.1 (2.5)
B
AK-R2-030P1K2, AK-R2-120P1K2
2.7 (6)
Figure B.9 Recommended External Brake Resistor Circuitry
Three-Phase
AC Input
(Input Contactor) M
R (L1)
S (L2)
T (L3)
Power Off
Power On
M
M
Power Source
DB Resistor Thermostat
PowerFlex 40 Adjustable Frequency AC Drive FRN 1.xx - 6.xx User Manual
Publication 22B-UM001H-EN-E
22B-UM001.book Page 14 Wednesday, January 22, 2014 11:04 AM
B-14
Accessories and Dimensions
Figure B.10 Bulletin 1321-3R Series Line Reactors – Dimensions are in millimeters
and (inches). Weights are in kilograms and (pounds).
A
B
E
D
C
Catalog Number
A
B
C
D
E
Weight
1321-3R2-A
112 (4.40)
104 (4.10)
70 (2.75)
50 (1.98)
37 (1.44)
1.8 (4)
1321-3R2-B
112 (4.40)
104 (4.10)
70 (2.75)
50 (1.98)
37 (1.44)
1.8 (4)
1321-3R4-A
112 (4.40)
104 (4.10)
76 (3.00)
50 (1.98)
37 (1.44)
1.8 (4)
1321-3R4-B
112 (4.40)
104 (4.10)
76 (3.00)
50 (1.98)
37 (1.44)
1.8 (4)
1321-3R4-C
112 (4.40)
104 (4.10)
86 (3.38)
60 (2.35)
37 (1.44)
2.3 (5)
1321-3R4-D
112 (4.40)
104 (4.10)
92 (3.62)
66 (2.60)
37 (1.44)
2.7 (6)
1321-3R8-A
152 (6.00)
127 (5.00)
76 (3.00)
53 (2.10)
51 (2.00)
3.1 (7)
1321-3R8-B
152 (6.00)
127 (5.00)
76 (3.00)
53 (2.10)
51 (2.00)
3.6 (8)
1321-3R8-C
152 (6.00)
127 (5.00)
85 (3.35)
63 (2.48)
51 (2.00)
4.9 (11)
1321-3R12-A
152 (6.00)
127 (5.00)
76 (3.00)
53 (2.10)
51 (2.00)
4.1 (9)
1321-3R12-B
152 (6.00)
127 (5.00)
76 (3.00)
53 (2.10)
51 (2.00)
4.5 (10)
1321-3R18-A
152 (6.00)
133 (5.25)
79 (3.10)
54 (2.13)
51 (2.00)
4.1 (9)
1321-3R18-B
152 (6.00)
133 (5.25)
86 (3.40)
63 (2.48)
51 (2.00)
5.4 (12)
1321-3R25-A
183 (7.20)
146 (5.76)
85 (3.35)
60 (2.35)
76 (3.00)
4.9 (11)
1321-3R35-A
193 (7.60)
146 (5.76)
91 (3.60)
66 (2.60)
76 (3.00)
6.3 (14)
PowerFlex 40 Adjustable Frequency AC Drive FRN 1.xx - 6.xx User Manual
Publication 22B-UM001H-EN-E
22B-UM001.book Page 15 Wednesday, January 22, 2014 11:04 AM
Accessories and Dimensions
B-15
Figure B.11 Frame B EMC Line Filters – Dimensions are in millimeters and (inches)
Catalog Numbers: 22-RF8P0-BL, 22-RF012-BS, -BL (Series B); 22-RF018-BS;
22-RF021-BS, -BL
29.8
(1.17)
50
(1.97)
100
78 (3.94)
(3.07)
217
(8.54)
229
(9.02)
216
(8.50)
17.8
(0.70)
24.0
(0.94)
5.5 (0.22)
PowerFlex 40 Adjustable Frequency AC Drive FRN 1.xx - 6.xx User Manual
Publication 22B-UM001H-EN-E
22B-UM001.book Page 16 Wednesday, January 22, 2014 11:04 AM
B-16
Accessories and Dimensions
Figure B.12 Frame C EMC Line Filters – Dimensions are in millimeters and (inches)
Catalog Numbers: 22-RF018-CS, -CL; 22-RF025-CL; 22-RF026-CS, -CL; 22-RF034-CS,
-CL
32
(1.26)
60
(2.36)
130
90 (5.12)
(3.54)
297
(11.69)
309
(12.17)
297
(11.69)
17
(0.67)
30
(1.18)
PowerFlex 40 Adjustable Frequency AC Drive FRN 1.xx - 6.xx User Manual
Publication 22B-UM001H-EN-E
5.5 (0.22)
22B-UM001.book Page 17 Wednesday, January 22, 2014 11:04 AM
Accessories and Dimensions
B-17
Figure B.13 Remote (Panel Mount) Small HIM – Dimensions are in millimeters and
(inches) Catalog Number: 22-HIM-C2S
25
(0.98)
93
(3.66)
180
(7.09)
2m
67
(2.64)
60
(2.36)
154
(6.06)
19.1
(0.75)
77
(3.03)
4.8
(0.19)
23.5
(0.93)
PowerFlex 40 Adjustable Frequency AC Drive FRN 1.xx - 6.xx User Manual
Publication 22B-UM001H-EN-E
22B-UM001.book Page 18 Wednesday, January 22, 2014 11:04 AM
B-18
Accessories and Dimensions
Figure B.14 NEMA Type 1 Bezel – Dimensions are in millimeters and (inches)
Catalog Number: 22-HIM-B1
93
(3.66)
25.2
(0.99)
11.1
(0.44)
180
(7.09)
2m
67
(2.64)
60
(2.36)
154
(6.06)
4.8
(0.19)
77
(3.03)
19.1
(0.75)
23.5
(0.93)
PowerFlex 40 Adjustable Frequency AC Drive FRN 1.xx - 6.xx User Manual
Publication 22B-UM001H-EN-E
22B-UM001.book Page 1 Wednesday, January 22, 2014 11:04 AM
Appendix C
RS485 (DSI) Protocol
PowerFlex 40 drives support the RS485 (DSI) protocol to allow efficient
operation with Rockwell Automation peripherals. In addition, some
Modbus functions are supported to allow simple networking. PowerFlex
40 drives can be multi-dropped on an RS485 network using Modbus
protocol in RTU mode.
Controller
For information regarding DeviceNet or other communication protocols,
refer to the appropriate user manual.
Network Wiring
Network wiring consists of a shielded 2-conductor cable that is
daisy-chained from node to node.
Figure C.1 Network Wiring Diagram
PowerFlex 40
Node 1
Master
TxRxD+
4
120 ohm resistor
TxRxD-
5
Shield
PowerFlex 40
Node 2
TxRxD+
TxRxDShield
4
5
PowerFlex 40
Node "n"
TxRxD+
TxRxD-
4
FRONT
120 ohm resistor
5
Shield
PIN 1
PIN 8
NOTE: The shield should be grounded at ONLY ONE location.
01 02 03 04 05 06 07 08 09
01 02 03 04 05 06 07 08 09
11 12 13 14 15 16 17 18 19
R/L1 S/L2 T/L3 U/T1 V/T2 W/T3
DC- DC+ BR+ BR-
RS485
(DSI)
11 12 13 14 15 16 17 18 19
AK-U0-RJ45-TB2P
TxRxD- R/L1 S/L2 T/L3 U/T1 V/T2 W/T3
TxRxD+
RS485
(DSI)
TxRxDTxRxD+
DC- DC+ BR+ BR-
PowerFlex 40 Adjustable Frequency AC Drive FRN 1.xx - 6.xx User Manual
Publication 22B-UM001H-EN-E
22B-UM001.book Page 2 Wednesday, January 22, 2014 11:04 AM
C-2
RS485 (DSI) Protocol
Only pins 4 and 5 on the RJ45 plug should be wired. The other pins on
the PowerFlex 40 RJ45 socket must not be connected because they
contain power, etc. for other Rockwell Automation peripheral devices.
Wiring terminations on the master controller will vary depending on the
master controller used and “TxRxD+” and “TxRxD-” are shown for
illustration purposes only. Refer to the master controller’s user manual
for network terminations. Note that there is no standard for the “+” and
“-” wires, and consequently Modbus device manufacturers interpret
them differently. If you have problems with initially establishing
communications, try swapping the two network wires at the master
controller.
Standard RS485 wiring practices apply.
•
Termination resistors need to be applied at each end of the network
cable.
•
RS485 repeaters may need to be used for long cable runs, or if
greater than 32 nodes are needed on the network.
•
Network wiring should be separated from power wires by at least 0.3
meters (1 foot).
•
Network wiring should only cross power wires at a right angle.
I/O Terminal 19 on the PowerFlex 40 is connected to the metal shield
around the RJ45 connector. It is recommended to ground this terminal
(there are two PE terminals on the drive). See Table 1.H for more
information.
Network Common is internally tied to I/O Terminal 04 (Digital
Common). Tying I/O Terminal 04 to PE ground may improve noise
immunity in some applications.
PowerFlex 40 Adjustable Frequency AC Drive FRN 1.xx - 6.xx User Manual
Publication 22B-UM001H-EN-E
22B-UM001.book Page 3 Wednesday, January 22, 2014 11:04 AM
RS485 (DSI) Protocol
C-3
Parameter Configuration
The following PowerFlex 40 parameters are used to configure the drive
to operate on a network.
Parameter
Details
Reference
P036 [Start Source]
Set to 5 “RS485 (DSI) Port” if Start is controlled from
the network.
Page 3-10
P038 [Speed Reference]
Set to 5 “RS485 (DSI) Port” if the Speed Reference is
controlled from the network.
Page 3-12
A103 [Comm Data Rate]
Sets the data rate for the RS485 (DSI) Port. All nodes
on the network must be set to the same data rate.
Page 3-31
A104 [Comm Node Addr]
Sets the node address for the drive on the network.
Each device on the network requires a unique node
address.
Page 3-31
A105 [Comm Loss Action] Selects the drive’s response to communication
problems.
Page 3-32
A106 [Comm Loss Time]
Sets the time that the drive will remain in
Page 3-32
communication loss before the drive implements A105
[Comm Loss Action].
A107 [Comm Format]
Sets the transmission mode, data bits, parity and stop Page 3-32
bits for the RS485 (DSI) Port. All nodes on the network
must be set to the same setting.
Supported Modbus Function Codes
The peripheral interface (DSI) used on PowerFlex 40 drives supports
some of the Modbus function codes.
Modbus Function Code (Decimal)
Command
03
Read Holding Registers
06
Preset (Write) Single Register
16 (10 Hexadecimal)
Preset (Write) Multiple Registers
Important: Modbus devices can be 0-based (registers are numbered
starting at 0) or 1-based (registers are numbered starting at
1). Depending on the Modbus Master used, the register
addresses listed on the following pages may need to be
offset by +1. For example, Logic Command may be register
address 8192 for some master devices (e.g. ProSoft
3150-MCM SLC Modbus scanner) and 8193 for others
(e.g. PanelViews).
PowerFlex 40 Adjustable Frequency AC Drive FRN 1.xx - 6.xx User Manual
Publication 22B-UM001H-EN-E
22B-UM001.book Page 4 Wednesday, January 22, 2014 11:04 AM
C-4
RS485 (DSI) Protocol
Writing (06) Logic Command Data
The PowerFlex 40 drive can be controlled via the network by sending
Function Code 06 writes to register address 8192 (Logic Command).
P036 [Start Source] must be set to 5 “RS485 (DSI) Port” in order to
accept the commands.
In addition to being written, register address 8192 can be read using
Function Code 03.
Logic Command
Address (Decimal)
Bit(s)
Description
0
1 = Stop, 0 = Not Stop
1
1 = Start, 0 = Not Start
2
1 = Jog, 0 = No Jog
3
1 = Clear Faults, 0 = Not Clear Faults
00 = No Command
5,4
01 = Forward Command
10 = Reverse Command
11 = No Command
6
Not Used in FRN 3.03 and earlier.
In FRN 4.01 and later, activates Opto Output 1.
Note: This bit controls the output when the value of parameter
A058 is set to 20.
7
Not Used in FRN 3.03 and earlier.
In FRN 4.01 and later, activates Opto Output 2.
Note: This bit controls the output when the value of parameter
A061 is set to 20.
00 = No Command
8192
9,8
01 = Accel Rate 1 Enable
10 = Accel Rate 2 Enable
11 = Hold Accel Rate Selected
00 = No Command
11,10
01 = Decel Rate 1 Enable
10 = Decel Rate 2 Enable
11 = Hold Decel Rate Selected
000 = No Command
001 = Freq. Source = P038 [Speed Reference]
010 = Freq. Source = A069 [Internal Freq]
14,13,12
011 = Freq. Source = Comms (Addr 8193)
100 = A070 [Preset Freq 0]
101 = A071 [Preset Freq 1]
110 = A072 [Preset Freq 2]
111 = A073 [Preset Freq 3]
15
Not Used in FRN 3.03 and earlier.
In FRN 4.01 and later, activates C-form relay.
Note: This bit controls the output when the value of parameter
A055 is set to 20.
PowerFlex 40 Adjustable Frequency AC Drive FRN 1.xx - 6.xx User Manual
Publication 22B-UM001H-EN-E
22B-UM001.book Page 5 Wednesday, January 22, 2014 11:04 AM
RS485 (DSI) Protocol
C-5
Writing (06) Reference
The Speed Reference to a PowerFlex 40 drive can be controlled via the
network by sending Function Code 06 writes to register address 8193
(Reference). P038 [Speed Reference] must be set to 5 “RS485 (DSI)
Port” in order to accept the Speed Reference.
In addition to being written, register address 8193 can be read using
Function Code 03.
Reference
Address (Decimal)
8193
Description
A decimal value entered as xxx.x where the decimal point is fixed. For
example, a decimal “100” equals 10.0 Hz and “543” equals 54.3 Hz.
Reading (03) Logic Status Data
The PowerFlex 40 Logic Status data can be read via the network by
sending Function Code 03 reads to register address 8448 (Logic Status).
Logic Status
Address (Decimal)
8448
(1)
Bit(s)
Description
0
1 = Ready, 0 = Not Ready
1
1 = Active (Running), 0 = Not Active
2
1 = Cmd Forward, 0 = Cmd Reverse
3
1 = Rotating Forward, 0 = Rotating Reverse
4
1 = Accelerating, 0 = Not Accelerating
5
1 = Decelerating, 0 = Not Decelerating
6
1 = Alarm, 0 = No Alarm
7
1 = Faulted, 0 = Not Faulted
8
1 = At Reference, 0 = Not At Reference
9
1 = Reference Controlled by Comm
10
1 = Operation Cmd Controlled by Comm
11
1 = Parameters have been locked
12
Digital Input 1 Status
13
Digital Input 2 Status
14
Digital Input 3 Status(1)
15
Digital Input 4 Status(1)
This status is available only with firmware revision FRN 2.xx and higher.
PowerFlex 40 Adjustable Frequency AC Drive FRN 1.xx - 6.xx User Manual
Publication 22B-UM001H-EN-E
22B-UM001.book Page 6 Wednesday, January 22, 2014 11:04 AM
C-6
RS485 (DSI) Protocol
Reading (03) Feedback
The Feedback (Output Frequency) from the PowerFlex 40 drive can be
read via the network by sending Function Code 03 reads to register
address 8451 (Feedback).
Feedback(2)
Address (Decimal)
8451
(2)
Description
A xxx.x decimal value where the decimal point is fixed. For example, a decimal
“123” equals 12.3 Hz and “300” equals 30.0 Hz.
Returns the same data as Reading (03) Parameter d001 [Output Freq].
Reading (03) Drive Error Codes
The PowerFlex 40 Error Code data can be read via the network by
sending Function Code 03 reads to register address 8449 (Drive Error
Codes).
Logic Status
Address (Decimal)
8449
Value (Decimal)
Description
0
No Fault
2
Auxiliary Input
3
Power Loss
4
Undervoltage
5
Overvoltage
6
Motor Stalled
7
Motor Overload
8
Heatsink Overtemperature
12
HW Overcurrent (300%)
13
Ground Fault
29
Analog Input Loss
33
Auto Restart Tries
38
Phase U to Ground Short
39
Phase V to Ground Short
40
Phase W to Ground Short
41
Phase UV Short
42
Phase UW Short
43
Phase VW Short
63
Software Overcurrent
64
Drive Overload
70
Power Unit Fail
80
AutoTune Fail
81
Communication Loss
100
Parameter Checksum Error
122
I/O Board Fail
PowerFlex 40 Adjustable Frequency AC Drive FRN 1.xx - 6.xx User Manual
Publication 22B-UM001H-EN-E
22B-UM001.book Page 7 Wednesday, January 22, 2014 11:04 AM
RS485 (DSI) Protocol
C-7
Reading (03) and Writing (06) Drive Parameters
To access drive parameters, the Modbus register address equals the
parameter number. For example, a decimal “1” is used to address
Parameter d001 [Output Freq] and decimal “39” is used to address
Parameter P039 [Accel Time 1].
Additional Information
Refer to http://www.ab.com/drives/ for additional information.
PowerFlex 40 Adjustable Frequency AC Drive FRN 1.xx - 6.xx User Manual
Publication 22B-UM001H-EN-E
22B-UM001.book Page 8 Wednesday, January 22, 2014 11:04 AM
C-8
RS485 (DSI) Protocol
Notes:
PowerFlex 40 Adjustable Frequency AC Drive FRN 1.xx - 6.xx User Manual
Publication 22B-UM001H-EN-E
22B-UM001.book Page 1 Wednesday, January 22, 2014 11:04 AM
Appendix D
RJ45 DSI Splitter Cable
The PowerFlex 40 drive provides a RJ45 port to allow the connection of
a single peripheral device. The RJ45 DSI Splitter Cable can be used to
connect a second DSI peripheral device to the drive.
Connectivity Guidelines
!
ATTENTION: Risk of injury or equipment damage exists. The
peripherals may not perform as intended if these Connectivity
Guidelines are not followed. Precautions should be taken to follow
these Connectivity Guidelines.
•
•
•
•
Two peripherals maximum can be attached to a drive.
If a single peripheral is used, it must be connected to the Master port
(M) on the splitter and configured for “Auto” (default) or “Master.”
Parameter 9 [Device Type] on the DSI / MDI keypads and Parameter
1 [Adapter Cfg] on the Serial Converter are used to select the type
(Auto / Master / Slave).
Do not use the RJ45 Splitter Cable with a drive that has an
internal network communication adapter installed. Since only
one additional peripheral can be added, the second peripheral can be
connected directly to the RJ45 port on the drive. The internal Comm
is always the Master, therefore the external peripheral must be
configured as “Auto” (for temporary connections) or “Slave” (for
permanent connections).
If two peripherals will be powered up at the same time, one must be
configured as the “Master” and connected to the Master port (M) and
the other must be connected as the “Slave” and connected to the
Slave port (S).
PowerFlex 40 Adjustable Frequency AC Drive FRN 1.xx - 6.xx User Manual
Publication 22B-UM001H-EN-E
22B-UM001.book Page 2 Wednesday, January 22, 2014 11:04 AM
D-2
RJ45 DSI Splitter Cable
DSI Cable Accessories
PIN 1
S
Slave Port
M
RJ45 Splitter Cable – Catalog Number: AK-U0-RJ45-SC1
Master Port
PIN 8
RJ45 Two-Position Terminal Block Adapter –
Catalog Number: AK-U0-RJ45-TB2P
TB2
(PIN 5)
PIN 8
TB1
(PIN 4)
PIN 1
RJ45 Adapter with Integrated Termination Resistor –
Catalog Number: AK-U0-RJ45-TR1
PIN 8
PIN 1
PowerFlex 40 Adjustable Frequency AC Drive FRN 1.xx - 6.xx User Manual
Publication 22B-UM001H-EN-E
22B-UM001.book Page 3 Wednesday, January 22, 2014 11:04 AM
RJ45 DSI Splitter Cable
D-3
Connecting One Temporary Peripheral
DSI / MDI Drive
DSI / MDI
Hand Held
Serial Converter
or
M
DSI
S
Parameter 1 [Adapter Cfg] set to "Auto"
(default) or "Master" and connected to
Master port (M) on RJ45 Splitter Cable
Parameter 9 [Device Type] set to "Auto"
(default) or "Master" and connected to
Master port (M) on RJ45 Splitter Cable
Connecting One Temporary Peripheral and
One Permanent Peripheral
NEMA 1 Bezel
with DSI / MDI Hand Held
NEMA 4
Panel Mount Unit
DSI / MDI Drive
or
DSI
M
Parameter 9 [Device Type]
set to "Master" and
connected to Master port (M)
on RJ45 Splitter Cable
S
Parameter 1 [Adapter Cfg]
set to "Auto" (default) or
"Slave" and connected to
Slave port (S)
on RJ45 Splitter Cable
Serial Converter
PowerFlex 40 Adjustable Frequency AC Drive FRN 1.xx - 6.xx User Manual
Publication 22B-UM001H-EN-E
22B-UM001.book Page 4 Wednesday, January 22, 2014 11:04 AM
D-4
RJ45 DSI Splitter Cable
Connecting Two Permanent Peripherals
NEMA 1 Bezel
with DSI / MDI Hand Held
NEMA 4
Panel Mount Unit
DSI / MDI Drive
or
M
Parameter 9 [Device Type] set to
"Master" and connected to Master
port (M) on RJ45 Splitter Cable
S
Parameter 9 [Device Type]
set to "Slave" and
connected to Slave port (S)
on RJ45 Splitter Cable
or
Connecting an RS-485 Network
DSI / MDI Drives
AK-U0-RJ45-SC1
AK-U0-RJ45-TR1
Terminating Resistor
(end of network)
AK-U0-RJ45-TB2P
Two-position Terminal Block
or
or
Customer supplied RJ45 male-to-RJ45 male
cables with wires connected at pins 4 and 5 only.
Both the Master (M) and Slave (S) ports on the RJ45 Splitter
Cable operate as standard RS-485 ports in this configuration.
PowerFlex 40 Adjustable Frequency AC Drive FRN 1.xx - 6.xx User Manual
Publication 22B-UM001H-EN-E
22B-UM001.book Page 1 Wednesday, January 22, 2014 11:04 AM
Appendix E
StepLogic™, Basic Logic and
Timer/Counter Functions
Four PowerFlex 40 logic functions provide the capability to program
simple logic functions without a separate controller.
•
StepLogic Function
Steps through up to eight preset speeds based on programmed logic.
Programmed logic can include conditions that need to be met from
digital inputs programmed as “Logic In1” and “Logic In2” before
stepping from one preset speed to the next. A timer is available for
each of the eight steps and is used to program a time delay before
stepping from one preset speed to the next. The status of a digital
output can also be controlled based on the step being executed.
•
Basic Logic Function
Up to two digital inputs can be programmed as “Logic In1” and/or
“Logic In2”. A digital output can be programmed to change state
based on the condition of one or both inputs based on basic logic
functions such as AND, OR, NOR. The basic logic functions can be
used with or without StepLogic.
•
Timer Function
A digital input can be programmed for “Timer Start”. A digital
output can be programmed as a “Timer Out” with an output level
programmed to the desired time. When the timer reaches the time
programmed into the output level the output will change state. The
timer can be reset via a digital input programmed as “Reset Timer”.
•
Counter Function
A digital input can be programmed for “Counter In”. A digital output
can be programmed as “Counter Out” with an output level
programmed to the desired number of counts. When the counter
reaches the count programmed into the output level the output will
change state. The counter can be reset via a digital input
programmed as “Reset Counter”.
PowerFlex 40 Adjustable Frequency AC Drive FRN 1.xx - 6.xx User Manual
Publication 22B-UM001H-EN-E
22B-UM001.book Page 2 Wednesday, January 22, 2014 11:04 AM
E-2
StepLogic™, Basic Logic and Timer/Counter Functions
StepLogic Using Timed Steps
To activate this function, set parameter P038 [Speed Reference] to 6 “Stp
Logic”. Three parameters are used to configure the logic, speed
reference and time for each step.
•
Logic is defined using parameters A140-A147 [Stp Logic x].
•
Preset Speeds are set with parameters A070-A077 [Preset Freq x].
•
Time of operation for each step is set with parameters A150-A157
[Stp Logic Time x].
The direction of motor rotation can be forward or reverse.
Figure E.1 Using Timed Steps
Step 0
Step 1
Step 2
Step 3 Step 4 Step 5 Step 6
Step 7
Forward
0
Reverse
Time
StepLogic Sequence
•
Sequence begins with a valid start command.
•
A normal sequence begins with Step 0 and transition to the next step
when the corresponding StepLogic time has expired.
•
Step 7 is followed by Step 0
•
Sequence repeats until a stop is issued or a fault condition occurs.
PowerFlex 40 Adjustable Frequency AC Drive FRN 1.xx - 6.xx User Manual
Publication 22B-UM001H-EN-E
22B-UM001.book Page 3 Wednesday, January 22, 2014 11:04 AM
StepLogic™, Basic Logic and Timer/Counter Functions
E-3
StepLogic Using Basic Logic Functions
Digital input and digital output parameters can be configured to use logic
to transition to the next step. Logic In1 and Logic In2 are defined by
programming parameters A051-A054 [Digital Inx Sel] to option 23
“Logic In1” or option 24 “Logic In2”.
Example
•
Run at Step 0.
•
Transition to Step 1 when Logic In1 is true.
Logic senses the edge of Logic In1 when it transitions from off to on.
Logic In1 is not required to remain “on”.
•
Transition to Step 2 when both Logic In1 and Logic In2 are true.
The drive senses the level of both Logic In1 and Logic In2 and
transitions to Step 2 when both are on.
•
Transition to Step 3 when Logic In2 returns to a false or off state.
Inputs are not required to remain in the “on” condition except under
the logic conditions used for the transition from Step 2 to Step 3.
Start
Step 0
Step 1
Step 2
Step 3
Frequency
Logic In1
Logic In2
Time
The step time value and the basic logic may be used together to satisfy
machine conditions. For instance, the step may need to run for a
minimum time period and then use the basic logic to trigger a transition
to the next step.
Start
Step 0
Step 1
Frequency
Logic In1
Logic In2
Time
PowerFlex 40 Adjustable Frequency AC Drive FRN 1.xx - 6.xx User Manual
Publication 22B-UM001H-EN-E
22B-UM001.book Page 4 Wednesday, January 22, 2014 11:04 AM
E-4
StepLogic™, Basic Logic and Timer/Counter Functions
Timer Function
Digital inputs and outputs control the timer function and are configured
with parameters A051-A054 [Digital Inx Sel] set to 18 “Timer Start” and
20 “Reset Timer”.
Digital outputs (relay and opto type) define a preset level and indicate
when the level is reached. Level parameters A056 [Relay Out Level],
A059 [Opto Out1 Level] and A062 [Opto Out2 Level] are used to set the
desired time in seconds.
Parameters A055 [Relay Out Sel], A058 [Opto Out1 Sel] and A061
[Opto Out2 Sel] are set to option 16 “Timer Out” and causes the output
to change state when the preset level is reached.
Example
•
Drive starts up and accelerates to 30 Hz.
•
After 30Hz has been maintained for 20 seconds, a 4-20mA analog
input becomes the reference signal for speed control.
•
The timer function is used to select a preset speed with a 20 second
run time that overrides the speed reference while the digital input is
active.
•
Parameters are set to the following options:
–
P038 [Speed Reference] = 3 “4-20mA Input”
–
A051 [Digital In1 Sel] = 4 “Preset Freq”
–
A052 [Digital In2 Sel] = 18 “Timer Start”
–
A055 [Relay Out Sel] = 16 “Timer Out”
–
A056 [Relay Out Level] = 20.0 Secs
–
A071 [Preset Freq 1] = 30.0 Hz
•
The control terminal block is wired such that a start command will
also trigger the timer start.
•
The relay output is wired to I/O Terminal 05 (Digital Input 1) so that
it forces the input on when the timer starts.
•
After the timer is complete, the output is turned off releasing the
preset speed command. The drive defaults to following the analog
input reference as programmed.
PowerFlex 40 Adjustable Frequency AC Drive FRN 1.xx - 6.xx User Manual
Publication 22B-UM001H-EN-E
22B-UM001.book Page 5 Wednesday, January 22, 2014 11:04 AM
StepLogic™, Basic Logic and Timer/Counter Functions
E-5
Output
Frequency
Start
Relay Out
Photo Eye
Digital In1
Counter In
Digital In2
Reset Counter
Limit Switch
Note that a “Reset Timer” input is not required for this example since the
“Timer Start” input both clears and starts the timer.
PowerFlex 40 Adjustable Frequency AC Drive FRN 1.xx - 6.xx User Manual
Publication 22B-UM001H-EN-E
22B-UM001.book Page 6 Wednesday, January 22, 2014 11:04 AM
E-6
StepLogic™, Basic Logic and Timer/Counter Functions
Counter Function
Digital inputs and outputs control the counter function and are
configured with parameters A051-A054 [Digital Inx Sel] set to 19
“Counter In” and 21 “Reset Counter”.
Digital outputs (relay and opto type) define a preset level and indicate
when the level is reached. Level parameters A056 [Relay Out Level],
A059 [Opto Out1 Level] and A062 [Opto Out2 Level] are used to set the
desired count value.
Parameters A055 [Relay Out Sel], A058 [Opto Out1 Sel] and A061
[Opto Out2 Sel] are set to 17 “Counter Out” which causes the output to
change state when the level is reached.
Example
•
A photo eye is used to count packages on a conveyor line.
•
An accumulator holds the packages until 5 are collected.
•
A diverter arm redirects the group of 5 packages to a bundling area.
•
The diverter arm returns to its original position and triggers a limit
switch that resets the counter.
•
Parameters are set to the following options:
–
A051 [Digital In1 Sel] set to 19 to select “Counter In”
–
A052 [Digital In2 Sel] set to 21 to select “Reset Counter”
–
A055 [Relay Out Sel] set to 17 to select “Counter Out”
–
A056 [Relay Out Level] set to 5.0 (counts)
PowerFlex 40 Adjustable Frequency AC Drive FRN 1.xx - 6.xx User Manual
Publication 22B-UM001H-EN-E
22B-UM001.book Page 7 Wednesday, January 22, 2014 11:04 AM
StepLogic™, Basic Logic and Timer/Counter Functions
E-7
StepLogic Parameters
Table E.A Code Descriptions for Parameters A140-A147
Digit 3
Digit 2
Digit 1
Digit 0
0
0
F
1
Table E.B Digit 3 – Defines the action during the step currently executing.
Setting
Accel/Decel
Parameters Used
StepLogic Output
State
Commanded Direction
0
1
Off
FWD
1
1
Off
REV
2
1
Off
No Output
3
1
On
FWD
4
1
On
REV
5
1
On
No Output
6
2
Off
FWD
7
2
Off
REV
8
2
Off
No Output
9
2
On
FWD
A
2
On
REV
b
2
On
No Output
Table E.C Digit 2 – Defines what step to jump to or how to end program when the
logic conditions specified in Digit 1 are met.
Setting
Logic
0
Jump to Step 0
1
Jump to Step 1
2
Jump to Step 2
3
Jump to Step 3
4
Jump to Step 4
5
Jump to Step 5
6
Jump to Step 6
7
Jump to Step 7
8
End Program (Normal Stop)
9
End Program (Coast to Stop)
A
End Program and Fault (F2)
PowerFlex 40 Adjustable Frequency AC Drive FRN 1.xx - 6.xx User Manual
Publication 22B-UM001H-EN-E
22B-UM001.book Page 8 Wednesday, January 22, 2014 11:04 AM
E-8
StepLogic™, Basic Logic and Timer/Counter Functions
Table E.D Digit 1 – Defines what logic must be met to jump to a step other than the
very next step.
Setting
Description
Logic
0
Skip Step (jump immediately)
SKIP
1
Step based on the time programmed in the respective [Stp Logic Time x] TIMED
parameter.
2
Step if “Logic In1” is active (logically true)
TRUE
3
Step if “Logic In2” is active (logically true)
TRUE
4
Step if “Logic In1” is not active (logically false)
FALSE
5
Step if “Logic In2” is not active (logically false)
FALSE
6
Step if either “Logic In1” or “Logic In2” is active (logically true)
OR
7
Step if both “Logic In1” and “Logic In2” is active (logically true)
AND
8
Step if neither “Logic In1” or “Logic In2” is active (logically true)
NOR
9
Step if “Logic In1” is active (logically true) and “Logic In2” is not active
(logically false)
XOR
A
Step if “Logic In2” is active (logically true) and “Logic In1” is not active
(logically false)
XOR
b
Step after [Stp Logic Time x] and “Logic In1” is active (logically true)
TIMED AND
C
Step after [Stp Logic Time x] and “Logic In2” is active (logically true)
TIMED AND
d
Step after [Stp Logic Time x] and “Logic In1” is not active (logically false) TIMED OR
E
Step after [Stp Logic Time x] and “Logic In2” is not active (logically false) TIMED OR
F
Do not step OR no “jump to”, so use Digit 0 logic
IGNORE
Table E.E Digit 0 – Defines what logic must be met to jump to the very next step.
Setting
Description
Logic
0
Skip Step (jump immediately)
SKIP
1
Step based on the time programmed in the respective [Stp Logic Time x] TIMED
parameter.
2
Step if “Logic In1” is active (logically true)
TRUE
3
Step if “Logic In2” is active (logically true)
TRUE
4
Step if “Logic In1” is not active (logically false)
FALSE
5
Step if “Logic In2” is not active (logically false)
FALSE
6
Step if either “Logic In1” or “Logic In2” is active (logically true)
OR
7
Step if both “Logic In1” and “Logic In2” is active (logically true)
AND
8
Step if neither “Logic In1” or “Logic In2” is active (logically true)
NOR
9
Step if “Logic In1” is active (logically true) and “Logic In2” is not active
(logically false)
XOR
A
Step if “Logic In2” is active (logically true) and “Logic In1” is not active
(logically false)
XOR
b
Step after [Stp Logic Time x] and “Logic In1” is active (logically true)
TIMED AND
C
Step after [Stp Logic Time x] and “Logic In2” is active (logically true)
TIMED AND
d
Step after [Stp Logic Time x] and “Logic In1” is not active (logically false) TIMED OR
E
Step after [Stp Logic Time x] and “Logic In2” is not active (logically false) TIMED OR
F
Use logic programmed in Digit 1
PowerFlex 40 Adjustable Frequency AC Drive FRN 1.xx - 6.xx User Manual
Publication 22B-UM001H-EN-E
IGNORE
22B-UM001.book Page 1 Wednesday, January 22, 2014 11:04 AM
Appendix F
PID Set Up
PID Loop
The PowerFlex 40 has a built-in PID (proportional, integral, differential)
control loop. The PID loop is used to maintain a process feedback (such
as pressure, flow or tension) at a desired set point. The PID loop works
by subtracting the PID feedback from a reference and generating an error
value. The PID loop reacts to the error, based on the PID Gains, and
outputs a frequency to try to reduce the error value to 0. To enable the
PID loop, parameter A132 [PID Ref Sel] must be set to an option other
than 0 “PID Disabled”.
Exclusive Control and Trim Control are two basic configurations where
the PID loop may be used.
PowerFlex 40 Adjustable Frequency AC Drive FRN 1.xx - 6.xx User Manual
Publication 22B-UM001H-EN-E
22B-UM001.book Page 2 Wednesday, January 22, 2014 11:04 AM
F-2
PID Set Up
Exclusive Control
In Exclusive Control, the Speed Reference becomes 0, and the PID
Output becomes the entire Freq Command. Exclusive Control is used
when A132 [PID Ref Sel] is set to option 1, 2, 3 or 4. This configuration
does not require a master reference, only a desired set point, such as a
flow rate for a pump.
PID Loop
PID Ref
+
PID Fdbk
–
PID
Error
PID Prop Gain
PID
Output
+
PID Integ Time
+
Accel/Decel
Ramp
Freq
Command
+
PID Diff Rate
PID Enabled
Example
•
In a pumping application, the PID Reference equals the Desired
System Pressure set point.
•
The Pressure Transducer signal provides PID Feedback to the drive.
Fluctuations in actual system pressure, due to changes in flow, result
in a PID Error value.
•
The drive output frequency increases or decreases to vary motor
shaft speed to correct for the PID Error value.
•
The Desired System Pressure set point is maintained as valves in the
system are opened and closed causing changes in flow.
•
When the PID Control Loop is disabled, the Commanded Speed is
the Ramped Speed Reference.
PID Feedback =
Pressure Transducer Signal
Pump
PID Reference =
Desired System Pressure
PowerFlex 40 Adjustable Frequency AC Drive FRN 1.xx - 6.xx User Manual
Publication 22B-UM001H-EN-E
22B-UM001.book Page 3 Wednesday, January 22, 2014 11:04 AM
PID Set Up
F-3
Trim Control
In Trim Control, the PID Output is added to the Speed Reference. In
Trim mode, the output of the PID loop bypasses the accel/decel ramp as
shown. Trim Control is used when A132 [PID Ref Sel] is set to option 5,
6, 7 or 8.
P038 [Speed Reference]
PID Loop
PID Ref
+
PID Fdbk
–
PID
Error
Accel/Decel
Ramp
PID Prop Gain
+
PID Integ Time
+
PID
Output
+
+
Output
Freq
+
PID Diff Rate
PID Enabled
Example
•
In a winder application, the PID Reference equals the Equilibrium
set point.
•
The Dancer Pot signal provides PID Feedback to the drive.
Fluctuations in tension result in a PID Error value.
•
The Master Speed Reference sets the wind/unwind speed.
•
As tension increases or decreases during winding, the Speed
Reference is trimmed to compensate. Tension is maintained near the
Equilibrium set point.
0 Volts
PID Reference =
Equilibrium Set Point
PID Feedback =
Dancer Pot Signal
10 Volts
P038 [Speed Reference]
PowerFlex 40 Adjustable Frequency AC Drive FRN 1.xx - 6.xx User Manual
Publication 22B-UM001H-EN-E
22B-UM001.book Page 4 Wednesday, January 22, 2014 11:04 AM
F-4
PID Set Up
PID Reference and Feedback
Parameter A132 [PID Ref Sel] is used to enable the PID mode (A132 ¦ 0
“PID Disabled”) and to select the source of the PID Reference. If A132
[PID Ref Sel] is not set to 0 “PID Disabled”, PID can still be disabled by
select programmable digital input options (parameters A051-A054) such
as “Jog”, “Local” or “PID Disable”.
Table F.A A132 [PID Ref Sel] Options
Option
Description
0 “PID Disabled”
Disables the PID loop (default setting)
1 “PID Setpoint“
Selects Exclusive Control. A137 [PID Setpoint] will be used to
set the value of the PID Reference
2 “0-10V Input”
Selects Exclusive Control. Selects the 0-10V Input. Note that
the PID will not function with a bipolar analog input. It will
ignore any negative voltages and treat them like a zero.
3 “4-20mA Input”
Selects Exclusive Control. Selects the 4-20mA Input.
4 “Comm Port”
Selects Exclusive Control. The reference word from a
communication network (see Appendix C for details on the
reference word) such as Modbus RTU or DeviceNet becomes
the PID Reference. The value sent over the network is scaled
so that P035 [Maximum Freq] x 10 = 100% reference. For
example, with [Maximum Freq] = 60 Hz, a value of 600 sent
over the network would represent 100% reference.
5 “Setpnt, Trim”
Selects Trim Control. A137 [PID Setpoint] will be used to set
the value of the PID Reference.
6 “0-10V, Trim”
Selects Trim Control. Selects the 0-10V Input. Note that the
PID will not function with a bipolar analog input. It will ignore
any negative voltages and treat them like a zero.
7 “4-20mA, Trim”
Selects Trim Control. Selects the 4-20mA Input.
8 “Comm, Trim”
Selects Trim Control. The reference word from a
communication network (see Appendix C for details on the
reference word) such as Modbus RTU or DeviceNet becomes
the PID Reference. The value sent over the network is scaled
so that P035 [Maximum Freq] x 10 = 100% reference. For
example, with [Maximum Freq] = 60 Hz, a value of 600 sent
over the network would represent 100% reference.
A133 [PID Feedback Sel] is used to select the source of the PID
feedback.
Table F.B A133 [PID Feedback Sel] Options
Option
Description
0 “0-10V Input”
Selects the 0-10V Input (default setting). Note that the PID will
not function with a bipolar analog input. It will ignore any
negative voltages and treat them like a zero.
1 “4-20mA Input“
Selects the 4-20mA Input.
2 “Comm Port”
The reference word from a communication network (see
Appendix C of the PowerFlex 40 User Manual for details on the
reference word) such as Modbus RTU or DeviceNet becomes
the PID Feedback. The value sent over the network is scaled
so that P035 [Maximum Freq] x 10 = 100% Feedback. For
example, with [Maximum Freq] = 60 Hz, a value of 600 sent
over the network would represent 100% Feedback.
PowerFlex 40 Adjustable Frequency AC Drive FRN 1.xx - 6.xx User Manual
Publication 22B-UM001H-EN-E
22B-UM001.book Page 5 Wednesday, January 22, 2014 11:04 AM
PID Set Up
F-5
Analog PID Reference Signals
Parameters A110 [Anlg In 0-10V Lo] and A111 [Anlg In 0-10V Hi] are
used to scale or invert an analog PID Reference.
Important: Firmware version FRN 2.xx also allows PID Feedback
scaling from an analog input.
Examples
Scale Function
For a 0-5 volt signal, the following parameter settings are used so that a 0
volt signal = 0% PID Reference and a 5 volt signal = 100% PID
Reference.
• A110 [Anlg In 0-10V Lo] = 0.0%
• A111 [Anlg In 0-10V Hi] = 50.0%
• A132 [PID Ref Sel] = 0 “0-10V Input”
12
Input Volts
10
8
6
4
2
0
10
20
30
40
50
60
70
80
90 100
PID Reference (%)
PowerFlex 40 Adjustable Frequency AC Drive FRN 1.xx - 6.xx User Manual
Publication 22B-UM001H-EN-E
22B-UM001.book Page 6 Wednesday, January 22, 2014 11:04 AM
F-6
PID Set Up
Invert Function
For a 4-20mA signal, the following parameter settings are used so that a
20mA signal = 0% PID Reference and a 4mA signal = 100% PID
Reference.
• A112 [Anlg In 4-20mA Lo] = 100.0%
• A113 [Anlg In 4-20mA Hi] = 0.0%
• A132 [PID Ref Sel] = 3 “4-20mA Input”
4-20mA Input
24
20
16
12
8
4
0
10
20
30
40
50
60
70
80
90 100
PID Reference (%)
Alternatively, you can set the value of A167 [PID Invert Error] to 1 to
change the sign of the PID error. See A167 [PID Invert Error] in Chapter
3 for more details.
PID Deadband
Parameter A138 [PID Deadband] is used to set a range, in percent, of the
PID Reference that the drive will ignore.
Example
•
[PID Deadband] is set to 5.0
•
The PID Reference is 25.0%
•
The PID Regulator will not act on a PID Error that falls between 20.0
and 30.0%
PowerFlex 40 Adjustable Frequency AC Drive FRN 1.xx - 6.xx User Manual
Publication 22B-UM001H-EN-E
22B-UM001.book Page 7 Wednesday, January 22, 2014 11:04 AM
PID Set Up
F-7
PID Preload
The value set in A139 [PID Preload], in Hertz, will be pre-loaded into
the integral component of the PID at any start or enable. This will cause
the drive’s frequency command to initially jump to that preload
frequency, and the PID loop starts regulating from there.
PID Enabled
PID Output
PID Pre-load Value
Freq Cmd
PID Pre-load Value > 0
PID Limits
A130 [PID Trim Hi] and A131 [PID Trim Lo] are used to limit the PID
output and are only used in trim mode. [PID Trim Hi] sets the maximum
frequency for the PID output in trim mode. [PID Trim Lo] sets the
reverse frequency limit for the PID output in trim mode. Note that when
the PID reaches the Hi or Lo limit, the PID regulator stops integrating so
that windup does not occur.
PowerFlex 40 Adjustable Frequency AC Drive FRN 1.xx - 6.xx User Manual
Publication 22B-UM001H-EN-E
22B-UM001.book Page 8 Wednesday, January 22, 2014 11:04 AM
F-8
PID Set Up
PID Gains
The proportional, integral, and differential gains make up the PID
regulator.
•
A134 [PID Prop Gain]
The proportional gain (unitless) affects how the regulator reacts to
the magnitude of the error. The proportional component of the PID
regulator outputs a speed command proportional to the PID error. For
example, a proportional gain of 1 would output 100% of max
frequency when the PID error is 100% of the analog input range. A
larger value for [PID Prop Gain] makes the proportional component
more responsive, and a smaller value makes it less responsive.
Setting [PID Prop Gain] to 0.00 disables the proportional component
of the PID loop.
•
A135 [PID Integ Time]
The integral gain (units of seconds) affects how the regulator reacts
to error over time and is used to get rid of steady state error. For
example, with an integral gain of 2 seconds, the output of the integral
gain component would integrate up to 100% of max frequency when
the PID error is 100% for 2 seconds. A larger value for [PID Integ
Time] makes the integral component less responsive, and a smaller
value makes it more responsive. Setting [PID Integ Time] to 0
disables the integral component of the PID loop.
•
A136 [PID Diff Rate]
The Differential gain (units of 1/seconds) affects the rate of change
of the PID output. The differential gain is multiplied by the
difference between the previous error and current error. Thus, with a
large error the D has a large effect and with a small error the D has
less of an effect. This parameter is scaled so that when it is set to
1.00, the process response is 0.1% of [Maximum Freq] when the
process error is changing at 1% / second. A larger value for [PID Diff
Rate] makes the differential term have more of an effect and a small
value makes it have less of an effect. In many applications, the D
gain is not needed. Setting [PID Diff Rate] to 0.00 (factory default)
disables the differential component of the PID loop.
PowerFlex 40 Adjustable Frequency AC Drive FRN 1.xx - 6.xx User Manual
Publication 22B-UM001H-EN-E
22B-UM001.book Page 9 Wednesday, January 22, 2014 11:04 AM
PID Set Up
F-9
Guidelines for Adjusting the PID Gains
1. Adjust the proportional gain. During this step it may be desirable to
disable the integral gain and differential gain by setting them to 0.
After a step change in the PID Feedback:
–
If the response is too slow increase A134 [PID Prop Gain].
–
If the response is too quick and/or unstable (see Figure F.1),
decrease A134 [PID Prop Gain].
–
Typically, A134 [PID Prop Gain] is set to some value below the
point where the PID begins to go unstable.
2. Adjust the integral gain (leave the proportional gain set as in Step 1).
After a step change in the PID Feedback:
–
If the response is too slow (see Figure F.2), or the PID Feedback
does not become equal to the PID Reference, decrease A135
[PID Integ Time].
–
If there is a lot of oscillation in the PID Feedback before settling
out (see Figure F.3), increase A135 [PID Integ Time].
3. At this point, the differential gain may not be needed. However, if
after determining the values for A134 [PID Prop Gain] and A135
[PID Integ Time]:
–
Response is still slow after a step change, increase A136 [PID
Diff Rate].
–
Response is still unstable, decrease A136 [PID Diff Rate].
PowerFlex 40 Adjustable Frequency AC Drive FRN 1.xx - 6.xx User Manual
Publication 22B-UM001H-EN-E
22B-UM001.book Page 10 Wednesday, January 22, 2014 11:04 AM
F-10
PID Set Up
The following figures show some typical responses of the PID loop at
different points during adjustment of the PID Gains.
Figure F.1 Unstable
PID Reference
PID Feedback
Time
Figure F.2 Slow Response – Over Damped
PID Reference
PID Feedback
Time
Figure F.3 Oscillation – Under Damped
PID Reference
PID Feedback
Time
Figure F.4 Good Response – Critically Damped
PID Reference
PID Feedback
Time
PowerFlex 40 Adjustable Frequency AC Drive FRN 1.xx - 6.xx User Manual
Publication 22B-UM001H-EN-E
22B-UM001.book Page 1 Wednesday, January 22, 2014 11:04 AM
Index
A
AC Supply
Ground, 1-7
Source, 1-5
Ungrounded, 1-5
Acceleration Rate, 1-24
Advanced Program Group
Parameters, 3-14
Ambient Temperatures, 1-3
Analog Input Loss Fault, F29, 4-3
Armored Cable, 1-10
Auto Rstrt Tries Fault, F33, 4-4
Auxiliary Input Fault, F2, 4-3
B
Before Applying Power, 2-1
Bus Capacitors, Discharging, P-3, 1-2
C
Drive, B-7
Minimum Clearances, 1-3
Direction
of Drive, 2-2
of Motor, 1-13
Discharging Bus Capacitors, P-3, 1-2
Disconnecting Output Power, 1-12
Display, 2-4
Display Group Parameters, 3-3
Distribution Systems, Ungrounded,
1-5
Drive Frame Size, P-2, B-7
Drive Grounding, 1-7
Drive Overload Fault, F64, 4-4
Drive Ratings, P-4, A-1
DriveExecutive, 3-1
DriveExplorer, 3-1
E
Cable Length, 1-15
Cable, Power, 1-10
Capacitors, Discharging, P-3, 1-2
Catalog Number Explanation, P-4
CE Conformity, 1-25
Checklist, Start-Up, 2-1
Circuit Breakers, 1-8
Comm Loss Fault, F81, 4-4
Command Sources for Start and
Speed, 1-23
Common Symptoms and Corrective
Action, 4-5
Contactors, 1-14
Control Wiring, 1-16
Control, 2 and 3 Wire, 1-18
Conventions, Manual, P-2
Cover, Opening, 1-1
Cross Reference, Parameter
by Name, 3-45
D
Data, Diagnostic, 2-7
Data, Saving, 2-7
Deceleration Rate, 1-24
Dimensions
Earthing, see Grounding
Edit Parameters, 2-5
EMC/RFI
Grounding, Filter, 1-8
Interference, 1-25
Enclosure Rating, Changing, 1-3
ESD, Static Discharge, P-3
F
Faults
Analog Input Loss, F29, 4-3
Auto Rstrt Tries, F33, 4-4
Auxiliary Input, F2, 4-3
Comm Loss, F81, 4-4
Drive Overload, F64, 4-4
Ground Fault, F13, 4-3
Heatsink OvrTmp, F8, 4-3
HW OverCurrent, F12, 4-3
I/O Board Fail, F122, 4-5
Motor Overload, F7, 4-3
Motor Stalled, F6, 4-3
Net Loss, F71, 4-4
OverVoltage, F5, 4-3
Parameter Checksum, F100, 4-5
PowerFlex 40 Adjustable Frequency AC Drive FRN 1.xx - 6.xx User Manual
Publication 22B-UM001H-EN-E
22B-UM001.book Page 2 Wednesday, January 22, 2014 11:04 AM
Index-2
Params Defaulted, F48, 4-4
Phase Short, F41-F43, 4-4
Phase to Ground Short, F38-F40,
4-4
Power Loss, F3, 4-3
Power Unit, F70, 4-4
SVC Autotune, F80, 4-4
SW OverCurrent, F63, 4-4
UnderVoltage, F4, 4-3
File
Monitor, 3-3
Filter, RFI, 1-8
Frame Designations, P-2, A-1, B-7
Fuses
Minimum Recommendations, 1-8
Ratings, A-1
G
General Precautions, P-3
Ground Fault, F13, 4-3
Grounding
Filter, 1-8
General, 1-7
H
Heatsink OvrTmp Fault, F8, 4-3
HW OverCurrent Fault, F12, 4-3
I
I/O
Block Diagram, 1-16
Terminal Block, 1-15
Terminal Designations, 1-17
Wiring, 1-14
Wiring Examples, 1-18
Wiring Multiple Drives, 1-22
I/O Board Fail Fault, F122, 4-5
Input Contactor, 1-14
Input Fusing, 1-8
Input Potentiometer, 1-18
Input Power Conditioning, 1-6
Installation of Drive, 1-1
Integral Keypad, 2-4
Interference, EMC/RFI, 1-25
IP66 Installations, 1-14
K
Keypad, 2-4
L
LEDs, 2-4
M
Menu Structure, 2-6
Minimum Clearances, 1-3
Monitor File, 3-3
Motor
Cable Length, 1-12
Changing Forward Direction of,
1-13
Disconnect, 1-12
Motor Overload Fault, F7, 4-3
Motor Stalled Fault, F6, 4-3
Motor Starter, Bulletin 140M, 1-8
Mounting Options and Clearances,
1-3
MOV Jumper Location and Removal,
1-5
N
NEMA/UL Type 4X Installations, 1-14
Net Loss Fault, F71, 4-4
O
Opening the Drive Cover, 1-1
Operating Temperatures, 1-3
Operator Interface, 2-4
Output Disconnect, 1-12
OverVoltage Fault, F5, 4-3
P
Parameter
Descriptions, 3-1
Types, 3-1
Viewing and Editing, 2-5, 2-6
Parameter Checksum Fault, F100,
4-5
Parameter Cross Reference
by Name, 3-45
Parameters
Advanced Program Group, 3-14
Display Group, 3-3
PowerFlex 40 Adjustable Frequency AC Drive FRN 1.xx - 6.xx User Manual
Publication 22B-UM001H-EN-E
22B-UM001.book Page 3 Wednesday, January 22, 2014 11:04 AM
Index-3
Program Group, 3-9
Params Defaulted Fault, F48, 4-4
PE Ground, 1-7
Phase Short Fault, F41-F43, 4-4
Phase to Ground Fault, F38-F40, 4-4
Potentiometer, Wiring, 1-18
Power Cables and Wiring, 1-10
Power Conditioning, 1-6
Power Loss Fault, F3, 4-3
Power Unit Fault, F70, 4-4
Powering Up the Drive, 2-1
Precautions, General, P-3
Preferences, Setting, 2-7
Product Selection, B-1
Program Group Parameters, 3-9
Programming, 3-1
PTC Analog Input Wiring, 1-18
R
Ratings, A-1
Reflective Wave Protection, 1-12
Removing Cover, 1-1
Repeated Start/Stop, 1-14
Repeated Start/Stop Precautions,
1-14
RFI, see EMC/RFI
RWR (Reflective Wave Reducer),
1-12
S
Static Discharge, ESD, P-3
Status LEDs, 2-4
Supply Source, AC, 1-5
SVC Autotune Fault, F80, 4-4
SW OverCurrent Fault, F63, 4-4
System Grounding, 1-7
T
Terminal Block
I/O, 1-15
Power, 1-13
Three Wire Control, 1-18
Two Wire Control, 1-18
U
UnderVoltage Fault, F4, 4-3
Ungrounded Supply, 1-5
Unshielded Power Cables, 1-10
W
Watts Loss, A-5
Wiring, 1-1
Block Diagram, 1-16
Examples, 1-18
I/O Terminal Descriptions, 1-17
Potentiometer, 1-18
Power, 1-10
PTC Example, 1-18
Recommendations, 1-14
Safety Ground, 1-7
Saving Data, Viewing, 2-7
Setting Preferences, 2-7
Shielded Power Cables, 1-10
Short Circuit Protection, 1-8
Sink/Source, 1-17
Software, 3-1
Speed, Control of, 2-2
Start and Speed Reference Selection
and Control, 1-23
Start/Stop
Drive, 2-2
Motor, 1-14
Starting/Stopping, The Motor, 1-14
Start-Up Checklist, 2-1
PowerFlex 40 Adjustable Frequency AC Drive FRN 1.xx - 6.xx User Manual
Publication 22B-UM001H-EN-E
22B-UM001.book Page 4 Wednesday, January 22, 2014 11:04 AM
Index-4
Notes:
PowerFlex 40 Adjustable Frequency AC Drive FRN 1.xx - 6.xx User Manual
Publication 22B-UM001H-EN-E
22B-UM001.book Page 1 Wednesday, January 22, 2014 11:04 AM
22B-UM001.book Page 2 Wednesday, January 22, 2014 11:04 AM
U.S. Allen-Bradley Drives Technical Support
Tel: (1) 262.512.8176, Fax: (1) 262.512.2222, Email: [email protected], Online: www.ab.com/support/abdrives
www.rockwellautomation.com
Power, Control and Information Solutions Headquarters
Americas: Rockwell Automation, 1201 South Second Street, Milwaukee, WI 53204-2496 USA,Tel: (1) 414.382.2000, Fax: (1) 414.382.4444
Europe/Middle East/Africa: Rockwell Automation, Vorstlaan/Boulevard du Souverain 36, 1170 Brussels, Belgium,Tel: (32) 2 663 0600, Fax: (32) 2 663 0640
Asia Pacific: Rockwell Automation, Level 14, Core F, Cyberport 3, 100 Cyberport Road, Hong Kong,Tel: (852) 2887 4788, Fax: (852) 2508 1846
Publication 22B-UM001H-EN-E – June 2013
Supersedes 22B-UM001G-EN-E - August 2008
Copyright © 2013 Rockwell Automation, Inc. All rights reserved.
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertisement