PWS6800

PWS6800
PWS6800
Installation and Operation manual
MAEN850 2006-12
English
PWS6800 Installation
1
PWS6800 Installation
1.1 Introduction
PWS6800 is a Human Machine Interface (HMI) with a 7.5” STN Liquid Crystal
Display, and is water- and dust-resistant according to IP65/NEMA4.
The HMI is CE-marked and meets your need to be highly transient-resistant while
in operation.
Also, its compact design makes connections with other machinery more flexible, thus
achieving the optimal performance of your machines.
ADP is used to design applications of the HMI; it is reliable, user-friendly and compatible with many models.
The latest released ADP Version 6.1 and above can be used to design applications for
the HMI.
1.2 Safety Precautions
Both the installer, the owner, and the operator of this HMI must read and understand this installation manual.
General
– Only qualified personnel may install or operate the HMI.
– The HMI must be installed according to the installation instructions.
– The HMI is designed for stationary installation on a plane surface, where the following conditions are fulfilled:
• no high explosive risks
• no strong magnetic fields
• no direct sunlight
• no large, sudden temperature changes
– Never allow fluids, metal filings or wiring debris to enter any openings in the
HMI. This may cause fire or electrical shock.
– The HMI fulfills the requirements of article 4 of EMC directive 89/336/EEC.
– Storing the HMI where the temperature is lower/higher than
recommended in this manual can cause the LCD display liquid to congeal/
become isotopic.
– The LCD display liquid contains a powerful irritant. In case of skin contact, wash
immediately with plenty of water. In case of eye contact, hold the eye open, flush
with plenty of water and get medical attention.
– The supplier is not responsible for modified, altered or reconstructed equipment.
– Use only parts and accessories manufactured according to specifications of the
supplier.
– Peripheral equipment must be appropriate for the application and location.
– The figures in this manual serves an illustrative purpose. Because of the many variables associated with any particular installation, the supplier cannot assume responsibility for actual use based on the figures.
Beijer Electronics, MAEN850
2
PWS6800 Installation
– The supplier neither guarantees that the HMI is suitable for your particular application, nor assumes responsibility for your product design, installation or operation.
Power Source
– The HMI is equipped with a 24 V DC input. Supply power other than 24 V DC
± 15% will severely damage the HMI. Thus, check the power supply supporting
the DC power regularly.
– To avoid electric shock, be sure the power cable is unplugged from the power outlet when connecting the cable to the HMI.
Installation
– Communication cables must be separated from the power cables for operational
circuits. Use shielded cables or it may cause unpredictable problems.
During Use
– Emergency stop and other safety functions may not be controlled from the HMI.
– Do not use force or sharp objects when touching the keys, display etc.
Service and Maintenance
– Only qualified personnel should carry out repairs.
– Before carrying out any cleaning or maintenance operations, disconnect the
equipment from the electrical supply.
– Clean the display and surrounding front cover with a soft cloth and mild detergent.
– Replacing the battery incorrectly may result in explosion. Only use batteries recommended by the supplier.
Dismantling and Scrapping
– The HMI or parts thereof shall be recycled according to local regulations.
– The following components contain substances that might be hazardous to health
and the environment: lithium battery, electrolytic capacitor and display.
!
Note:
Indicated loss of life, severe personal injury, or substantial property damage
will result if proper precautions are not taken.
1.3 Package Contents
6 x Installation Fasteners
1 x HMI
1 x Power Connector
(wired to the power supply )
3
Beijer Electronics, MAEN850
PWS6800 Installation
1.4 Mounting Procedure
1. Cut out the control front panel to match the dimensions (mm) specified under
the External and Cut-out dimensions chapter.
2. Mount the HMI into the cut-out. Insert the fixtures to the holes on the unit and
fasten the screws into the front panel. Do not tighten the screws with too much
or uneven force, or it may cause deformation of the HMI.
Step 1
Step 2
Step 3
90º
y
la
sp
Di
135º
135º
Max torque: 0.3 Nm
0º
Display
3. The HMI must be installed within an angle of 0° to 135° as shown above.
1.5 Grounding
Make sure that the HMI works properly. To prevent it from radiating radio frequency
noise, the HMI must be connected to earth ground.
– Without grounding, the HMI may be severely affected by excess noise. Make sure
that the grounding is done properly from the power connector at the rear side of
the HMI. When power is connected, make sure that the wire is grounded.
– Use a cable of at least 2 mm2 (AWG 14) to ground the HMI. Ground resistance
must be less than 100 Ohms (class3). Note that the ground cable must not be connected to the same ground point as the power circuit.
1.6 Power Supply and Wiring
The HMI must use a power supply with 24 V DC and the power consumption is
24W.
Warning:
To avoid an electric shock, be sure to switch off the power before connecting the communication/download cable to the HMI.
Steps to wire
1. Unplug the power connector and unscrew the screws.
2. Strip about 1 cm of insulation. Insert the wire all the way into the power connector and then turn the screws tight.
3. Plug in the connector to the power outlet of the HMI.
Note:
Power connector is already plugged in the power outlet of the HMI when the package is
first opened.
Beijer Electronics, MAEN850
4
PWS6800 Installation
1.7 External and Cut-out Dimensions
46.8
45.8
231.0
176.0
164.7
6.5
219.7
Cut-out dimension
165.8±0.5
220.8±0.5
(unit: mm)
5
Beijer Electronics, MAEN850
PWS6800 Installation
1.8 Description of Parts
Fixture mounting holes
Function keys
Power lamp
Communication lamps (x3)
Network lamp
Display
Dip Switches
1-12
CF card slot
USB Connector for
Printer / Memory Stick
USB Connector
for Transmission
DC Power
Outlet
Connects Network
COM1 (RS232, RS485)
COM2 (RS232, RS422, RS485)
Beijer Electronics, MAEN850
COM3 (RS422, RS485)
6
PWS6800 Installation
1.9 Product Specifications
Item
Display Type
Display Color
Display size
Display resolution
Back light
Touch Screen
Keypad
Keypad pressure and
lifetime
Input Power
Flash ROM
RAM
CPU
Battery backed memory
RTC
Data/Recipe
Data storage (CF card)
COM1
COM2
COM3
USB Master
USB Device
Multi-functional port
Ethernet
Front Panel seal
Operating temperature
Storage temperature
Ambient humidity
Vibration endurance
PWS6800C-N
PWS6800C-P
Color STN LCD
256 colors
7.5”
640 x 480, Number of 8 x 8 characters displayable 80 x 60
CCFT, Lifetime 45,000 hours @ 25 degrees Celsius
Analog
1 Menu key and user-defined Function keys (F1-F6)
350+-50 gf operating force, lifetime is over 1 million activations
24 V DC +-15%, less than 24W
4 Mb
512 K byte
32 bits RISC
512 K byte
YES (rechargeable lithium battery)
512 K byte
YES
9-pin female connector, RS232 and RS485
25-pin female connector, RS232, RS422 and RS485
9-pin female connector, RS422 and RS485
2 ports
1 port
YES
IP65 / NEMA 4
0° - 50° C
-10° - 60° C
20-90% (non-condensing)
0.5 mm displacement, 10-55 Hz, 2 hours per X, Y, Z axis directions
Shock endurance
10 G, 11 ms three times in each direction of X, Y, Z axes
RF Emissions
CISPR 22, Class A
Electrostatic discharge IEC61000-4-2
RF Susceptibility
IEC61000-4-3
High Frequency Tran- IEC61000-4-4
sients
External dimensions
231.0 x 176.0 x 46.8 mm
Cut-out dimensions
220.8 x 165.8 mm
Weight
1.2 kg
Cooling
Natural cooling
Note:
When using the HMI for the first time, remember to reset Real Time Clock (RTC).
7
Beijer Electronics, MAEN850
PWS6800 Installation
1.10 Communication Ports
– COM 1 is a 9-pin female connector used to connect a controller and the HMI via
RS232 or RS485
– COM 2 is a 25-pin female connector used to connect a controller and the HMI
via RS232, RS422 or RS485
– COM 3 is a 9-pin female connector used to connect a controller and the HMI via
RS422 or RS485
Please make sure that the connection is in accordance with the setting of the dip
switches. (For example, RS485 with SW 9, SW 10=ON and SW 11=ON)
For illustration on the connection between the HMI and a controller, please consult
the information on the controller.
COM 1
5 4
COM 2
13 12 11 10 9
3 2 1
8
7
6
5
4
3
2
1
25 24 23 22 21 20 19 18 17 16 15 14
9 8 7 6
PIN
1
2
3
4
5
6
7
8
9
Function
RS485+
RS232 RXD
RS232 TXD
N/A
Signal ground
RS485RS232 RTS
RS232 CTS
Optional +5 V @ 100mA output
COM 3
5 4
3 2 1
9 8 7 6
PIN
1
2
3
4
5
6
7
8
Function
RS422+ (RS485 TX+)
RS422 CTS+
RS422 CTSRS422 RX+
Signal ground
RS422- (RS485 TX-)
RS422 RTS+
RS422 RTS-
Beijer Electronics, MAEN850
PIN
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
Function
N/A
RS232 TXD
RS232 RXD
RS232 RTS
RS232 CTS
N/A
Signal ground
Optional +5 V @ 100mA output
N/A
N/A
N/A
RS422 CTS+
RS422 CTSRS422 TX+ (RS485+)
RS422 TX- (RS485-)
RS422 RX+
RS422 RXN/A
N/A
N/A
N/A
N/A
RS422 RTS+
RS422 RTSN/A
8
PWS6800 Installation
1.11 Dip Switches
Dip Switches
SW 1
SW 2
SW 3
ON
ON
OFF
OFF
SW 5
ON
OFF
SW 6
ON
OFF
SW 7
ON
OFF
SW 8
ON
OFF
SW 9
ON
SW 10
ON
OFF
SW 11
ON
OFF
SW 12
9
SW 4
ON
OFF
ON
OFF
Function
Reserved
Reserved
Operation Mode
Runs user application
Runs burn-in test program
Updates BIOS
Runs bench test program
Communication Parameters
The HMI uses parameters defined on the Configuration Screen for
controller communications
The HMI uses parameters defined in ADP for controller communications
Password
The HMI asks the operator to enter a password after power-on selftest
No password is required to start the HMI
System Menu
The HMI displays System Menu
The HMI runs user application without displaying System Menu
Default user level
The default user level is set to 1 if the HMI requires no password to
start its operation
The default user level is set to 9 if the HMI requires no password to
start its operation
COM 1 Port
For RS485 this switch has to be set ON
COM 2 Port
For RS485 this switch has to be set ON
For RS422 this switch has to be set OFF
COM 3 Port
For RS485 this switch has to be set ON
For RS422 this switch has to be set OFF
Reserved
Beijer Electronics, MAEN850
PWS6800 Operation
2
PWS6800 Operation
2.1 Self Test
Once the HMI is turned on, it will automatically execute a self-test to check its hardware. The result of a self-test is displayed on the LCD. See below for items to check
in a self-test:
Human Machine Interface
ROM BIOS Version 1.0
(C) 2006 Hitech Beijer Electronics
Display Type = Color STN LCD
System RAM Size ........... 16M Bytes
Video RAM Size ............
1M Bytes
Battery Backed RAM Size ... 512K Bytes
BIOS Memory Size .......... 128K Bytes
Firmware Memory Size ...... 512K Bytes
User Memory Size .......... 3456K Bytes
Battery Status ............ Passed
BIOS ROM Checksum ......... Passed
Firmware Checksum ......... Passed
Application Checksum ...... Passed
RTC Function Test ......... Passed
Parameter Checksum ........ Passed
Communcation Port 1 Test .. Passed
Communcation Port 2 Test .. Passed
DIP Switches Setting(8..1)= 11011111
If any of tests does not pass the self-test, it will be noted with “Failed” next to the test
item. Additionally, the message “Error! Press screen to continue” will be displayed at
the bottom of the screen.
If the power to the HMI or the PC was interrupted while downloading, Firmware
checksum or Application checksum will not pass the self-test, indicated by “Failed”
in the self-test results after power is restored. If this happens, the user can simply follow the download procedure to re-download the application or data. After downloading again, all items should pass the self-test.
2.2 System Menu
Set the dip switch SW7=ON. After the self-test, the system menu of the HMI is displayed on the screen:
The functions of the commands are briefly explained below:
System Menu
Link
F2 - Confg
F3 - Copy
F4 - Set
F5 - Run
Function
The HMI is connected.
Sets up the internal time clock and communication parameters in the
HMI. All the settings has to be made for the HMI to work properly.
Use , ,
and
to move to desired field; + and - to set the
value of the field.
Copies application data to another HMI.
Calibrates the touch screen, adjusts LCD contrast and clears RAM data.
Runs the application.
Beijer Electronics, MAEN850
10
PWS6800 Operation
2.3 Keypad
The seven keys on the HMI include one menu key and seven functional keys (F1 F6). Press the menu key to slide out the innovative slide-out menu. For further details
on the slide-out menu please see the ADP User’s Manual
Menu
Functional Keys F1-F6
When a key is pressed, the HMI will make a “beep” sound to signal that a command
is pressed. (The default setting is a 200 ms beep, and can be configured.)
2.4 Bench and Function Tests
Set the dip switches SW3 and SW4=OFF to be able to run the bench and function
tests for the HMI. Turn on the HMI and the following screen will be displayed.
The bench test performs an overall hardware test and the function test lets the user
select which item to be tested.
Note:
The bench test will clear the application data of the HMI.
2.5 Setting Communication Parameters
There are two ways to configure working parameters; to set parameters in the HMI
or in ADP.
To set parameters in the HMI, select F2 - Confg in the system menu.
Note:
Remember to set the dip switch SW5=ON if parameters are set in the HMI
To set parameters in ADP, select Application / Workstation Setup. Then select the
Connection tab to set communication parameters.
Note:
Remember to set the dip switch SW5=OFF if parameters are set in ADP
11
Beijer Electronics, MAEN850
PWS6800 Operation
2.6 Downloading an Application
Connect the RS232 port on the PC to the COM1 port on the HMI using a WPCP8-42 cable. The connection can also be made according to the illustration below.
PWS-COM1
9-pin male
RXD
TXD
GND
RTS
CTS
2
3
5
7
8
PC COM RS232
9-pin female
2
3
5
1
4
6
7
8
PWS ---- PC COM
PWS-COM2
25-pin male
RD
SD
SG
CD
DTR
DSR
RTS
CTS
TXD
RXD
GND
RTS
CTS
2
3
7
4
5
PC COM RS232
9-pin female
2
3
5
1
4
6
7
8
PWS ---- PC COM
RD
SD
SG
CD
DTR
DSR
RTS
CTS
Warning:
To avoid an electronic shock, be sure to switch off the power before connecting the
download cable to the HMI.
Set the dip switch SW7 = ON. After the self-test, the system menu will be displayed
on the screen and the HMI is ready to download the application.
Start ADP and open the application file to be downloaded. Make sure that the communication parameters are correctly configured. Also remember to compile the file
before downloading it. The file has to be compiled every time a change has been
made in the file before downloading it.
Then select Application/Download Firmware and then Application in ADP if it is
a first time to download the application to the HMI; otherwise, select Application/
Download Application. The following appears on the screen while the HMI is
downloading:
2.7 Uploading an Application
An application can also be uploaded from the HMI to the PC. Thus, a user can save
an application as a *.V6F file in ADP for future use.
Warning:
To avoid an electric shock, be sure to switch off the power before connecting the communication cable to the HMI.
Make sure that the HMI and the PC are connected according to section “Downloading an Application”. Set the dip switch SW7 = ON. After the self-test, the system
menu will be displayed on the screen and the HMI is ready to upload the application.
Also make sure that communication parameters are correctly configured. Select File/
Upload Application in ADP and the Save As dialog box will appear on the screen.
Enter the name of a firmware file (*.AF6) to save. Click Save. Then the HMI will
prompt for a password: enter the password set in ADP from Application/Workstation Setup. Once the correct password is entered, the HMI starts to upload the application to the PC. For information about setting a password, please see section
“Setting a Password“.
Beijer Electronics, MAEN850
12
PWS6800 Operation
While the HMI is uploading, the following is displayed:
After uploading, select File/Reconstruct Source in ADP to display the Open dialog.
Open the uploaded application file (*.C64 or *.AA6). The application screen will be
displayed on the PC monitor. Finally, select File/Save As to save the application as a
*.V6F file. Thus a source file can serve the purposes of maintenance and modification.
Note:
When using the HMI for the first time, make sure to first run the application once, or else
the upload function will not work.
2.8 Uploading / Downloading a Recipe
Set the dip switch SW7 = ON. After the self-test, the system menu will be displayed
on the screen and the HMI is ready to upload/download a recipe.
Uploading a Recipe
Select File/Upload Recipes in ADP and the Save As dialog box will appear on the
screen. Enter the name of a recipe file (*.RCP) to save. Click Save. While the HMI
is uploading the recipe, Uploading recipes is displayed on the screen.
Downloading a Recipe
Open an application file with the recipe to be downloaded in ADP. Select File/
Download Recipes to display the Open dialog. Enter the name of the recipe file
(*.RCP) and click Open. While the HMI is downloading the recipe, Downloading
recipes is displayed on the screen:
After the download is finished, select F5 - Run to run the application.
Remember to define the length and the number of recipes in the application. Also
remember to upload the format of recipes from the HMI
before starting to edit a new set of recipe data in the PC.
For further information about creating/editing recipes, please see the corresponding
chapter in the ADP User’s Manual.
13
Beijer Electronics, MAEN850
PWS6800 Operation
2.9 Copying an Application
To copy an application from one HMI to another, select F3 - Copy from the system
menu. Set the dip switch SW7 = ON and connect the two HMIs with a download
cable. After the self-test, the system menu will be displayed on the screen.
Select F3 - Copy in the system menu from the HMI with the application to be copied. The HMI will prompt for a password: enter the password set in ADP from Application/Workstation Setup. Once the correct password is entered, the HMI will
start to copy the application between the two HMIs. The following appears on the
screens during the copying:
Note:
If it is the first time to copy, please remember to run the application.
2.10 Setting a Password
Scenario 1: Requiring a password to start the HMI
If the dip switch SW6 = ON, the user needs to enter a password to start the HMI.
For this purpose, the designer can use the object Action Button in ADP to create a
button which displays the password table on the HMI display. A user with the right
to access the table can register passwords and user levels in the table. In the illustration below, the TBL-button is an action button used to display the password table.
When the button is selected the password table is displayed on the screen for a user
with the right to access the table. Touch the password to highlight an area for entering
a value.
In the illustration above, the TBL-button is an action button used to display the password table. When the button is selected the password table is displayed on the screen
for a user with the right to access the table. Touch the password to highlight an area
for entering a value.
How to configure an Action Button is described in the ADP User’s Manual.
After registering passwords and user levels, set the dip switch SW6 = ON (i.e. password required). Restart the HMI and after the self-test the user will be prompted to
enter a password in order to run the HMI. The HMI will determine the user level
from the entered password. For instance, if the level of the password entered by the
user is 2, then the HMI will set the user level to 2. User level 1 has the highest privilege and User level 9 has the lowest.
Note:
Only users of User Level 1 has the right of access to the password table.
Beijer Electronics, MAEN850
14
PWS6800 Operation
Scenario 2: Re-entering a password
The object Action Button in ADP also allows the designer to create a button which
asks the user to re-enter a password. For example, by pressing the PSW-button the
password keypad will be displayed to prompt the user to enter a password. After entering the password, the HMI will update the user level according to the most recent
password which has been entered. Therefore, this button can be applied to raise or
drop one’s privileges while the HMI is in operation.
How to configure an Action Button is described in the ADP User’s Manual.
Scenario 3: Password-protecting a button in the HMI
The ADP can create a button which is protected by a password for execution. For
example, a Goto Screen button can be designed with a high level of security; which
means that a password with a high level of privilege is required in order to open the
other screen. As the button is selected and the current user has a lower privilege than
has been set for the button, the HMI will prompt the user for a password. The user
will need a password with at least the level of privilege that has been set for the button. This function can restrict users to access to certain parts of the application.
Scenario 4: Requiring a password to copy or upload application
When selecting F3 - Copy in the system menu or File/Upload Application in ADP,
the HMI will prompt for a password. The user will need to enter the correct password
to copy an application from one HMI to another. Note that setting this password is
different from the passwords set in Scenarios 1-3. To set this password, select Application/Workstation Setup in ADP. Under the Password tab, the project designer is
able to set the password.
15
Beijer Electronics, MAEN850
Hitech Electronics Corp.
4F, No. 501-15, Chung-Cheng Road
Shin-Tien, Taipei Shien, Taiwan, R.O.C.
Telephone: +886-2-2218-3600
Telefax: +886-2-2218-9547
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertisement