C21/EC21 Web Pages

C21/EC21 Web Pages
The material in this manual is for information purposes only and is subject to
change without notice. Strand Lighting assumes no responsibility for any errors or
omissions, which may appear in this manual. For comments and suggestions
regarding corrections and/or updates to this manual, please contact the nearest
Strand Lighting office.
El contenido de este manual es solamente para información y está sujeto a
cambios sin previo aviso. Strand Lighting no asume responsabilidad por errores o
omisiones que puedan aparecer. Cualquier comentario, sugerencia o corrección
con respecto a este manual, favor de dirijirlo a la oficina de Strand Lighting más
cercana.
Der Inhalt dieses Handbuches ist nur für Informationszwecke gedacht,
Aenderungen sind vorbehalten. Strand Lighting uebernimmt keine Verantwortung
für Fehler oder Irrtuemer, die in diesem Handbuch auftreten. Für Bemerkungen
und Verbesserungsvorschlaege oder Vorschlaege in Bezug auf Korrekturen
und/oder Aktualisierungen in diesem Handbuch, moechten wir Sie bitten, Kontakt
mit der naechsten Strand Lighting-Niederlassung aufzunehmen.
Le matériel décrit dans ce manuel est pour information seulement et est sujet à
changements sans préavis. La compagnie Strand Lighting n’assume aucune
responsibilité sur toute erreur ou ommission inscrite dans ce manuel. Pour tous
commentaires ou suggestions concernant des corrections et/ou les mises à jour de
ce manuel, veuillez s’ll vous plait contacter le bureau de Strand Lighting le plus
proche.
© 2006 - 2009, Philips Group. All rights reserved.
Information contained in this document may not be duplicated in full or in part by
any person without prior written approval of Strand Lighting. Its sole purpose is to
provide the user with detailed installation information for the equipment supplied.
The use of this document for all other purposes is specifically prohibited.
C21 / EC21 Manual Part Number:
Revision Level:
Revision Date:
Written By:
2-450174-030
2.0
22-September-2009
Charles Coley, II
Prefix
Thank you for choosing Strand Lighting C21/EC21 series dimmer rack. We trust
that the equipment will meet all your dimming needs and will provide you with
reliable service for many years.
Strand Lighting can assure you that every effort has been made to ensure that the
equipment has been designed to meet the highest professional standards and that
dimmer racks and their components have been assembled, inspected, and tested
in accordance with our strict quality assurance program.
Should you encounter any problems or difficulties with your dimmer racks, please
contact the nearest Strand Lighting service representative. For a complete list of
Strand Lighting offices and service centers or visit our Web site
(www.strandlighting.com).
This manual describes the operation of for C21/EC21 series dimmer racks. A
separate Installation Guide provided with the dimmer racks describes how to install
the dimmer racks and perform initial setup procedures.
Strand Lighting Offices:
Strand Lighting, Inc.
Dallas
10911 Petal Street
Dallas, TX 75238
Tel: 214-647-7880
Fax: 214-647-8030
Strand Lighting, Inc.
New York
267 5th Ave, 4th Floor
New York, NY 10016
Tel: 212-213-8219
Fax: 212-532-2593
Strand Lighting Asia Limited
Room 6-10,
20/F Delta House 3 On Yiu Street
Shatin, N.T. Hong Kong
Tel: + 852 2757 3033
Fax: + 852 2757 1767
Page i
Strand Selecon
Auckland
19-21 Kawana Street
Northcote, Auckland 0627
New Zealand
Tel: +64 9 481 0100
Fax: +64 9 481 0101
Strand Lighting
Europe
Marssteden 152
Enschede 7547 TD
The Netherlands
Tel: +31 53 4500424
Fax: +31 53 4500425
C21/EC21 Series Dimmer Rack
Definition of Terms
This manual uses the following terms throughout:
channel
circuit
circuit ID
crossfade
cue
A device controlling a dimmer or group of dimmers. Historically, there is a physical
controller (such as a slider) for each channel. On most current control systems,
channels are numbers accessed by a numeric keypad. Each channel can control
multiple dimmers.
A connection device and wiring for powering a lighting fixture from a dimmer.
A unique four-digit numeric identity which you can assign to each dimmer. The
circuit ID may be the same as the dimmer number, or may be a number used to
indicate circuit location, phase, channel number, etc. This feature is useful for
system wide control functions.
A fade that contains both an up-fade and a down-fade, or any fade where the
levels of one cue are replaced by the levels of another cue.
The process of recalling a preset from its memory location and putting the result on
stage.
Preset, Memory, and cue are often used interchangeably.
curve
dimmer
default
A device controlling power to a lighting fixture. Two lights on the same dimmer
cannot be separately controlled.
The original factory settings.
DMX512
An ANSI communications protocol standard that describes a method of digital data
transmission between controllers, lighting equipment and accessories.
Ethernet
A high-speed network based protocol used to transmit data from a lighting
controller to a dimmer rack using a single Ethernet cable.
fade
fade time
level
Outlook
A gradual change in stage levels from one set of intensities (“look”) to another.
The time it takes for dimmer levels to go from their current levels to the levels in the
selected preset, or DMX value. Each preset has its own fade time.
A numerical value used to express the “brightness” of the load on a dimmer.
Usually shown as %.
A digital architectural control system for use with C21/EC21 dimmer racks.
patch
Historically, the process of physically connecting circuits to dimmers. Now usually
refers to electronic assignment of dimmers to channels.
phase
The three phases of the mains supply to which the dimmers are connected are
identified as Line 1, Line 2, Line 3 in 230v markets and as phase A, phase B, and
phase C in 120v markets.
power module
Operations Manual
The relationship between a control level and the actual dimmer output.
A chassis containing one, two or four dimmer or contactors. This is sometimes
referred to as a “dimmer”. However, each C21/EC21 power module can have
multiple dimmers or contactors in it, so this manual distinguishes between dimmers
(individual power control circuits) and power modules (a collection of one or more
power control circuits).
Page ii
preset
Preset fade time
profile
rack number
room
A pre-defined setup of intensities for a set of channels, stored in memory for later
replay. For Outlook applications, the C21/EC21 series dimmer rack processor
module stores 8 programmable presets per room for up to 16 rooms. For SWC
applications, the processor module stores 128 programmable presets. Preset 0
(ZERO) is always a blackout.
See “Fade Time”.
The relationship between a control level and the actual dimmer output. Also known
as ‘dimmer law‘ or ‘curve’.
A number used to uniquely identify each dimmer rack in a multiple rack system.
Rack numbers are set from the front panel of the rack processor module, and are
usually set by the installation engineer.
An area separately defined for purposes of architectural lighting control (e.g.,
Outlook control stations). This is usually a room in the traditional sense (an indoor
enclosed area) or a portion of a room that can be partitioned off. Each room may
be separately and simultaneously controlled by the system.
RPH
Rack Processor Housing
RPM
Rack Processor Module
SSR
(Solid State relay) A power control device used in Strand dimmers that contains
two silicon control rectifiers (SCRs), control circuitry, and optical isolation circuitry.
SWC
(System Wide Control) A method of programming and controlling more than one
dimmer rack simultaneously. A hand held controller lets you program and recall
128 presets, and control individual dimmers. 8 and 16 channel pushbutton
stations, and an A/V interface let you recall and 8 or 16 of the 128 presets at each
station. Please contact Strand Lighting or see the System Wide Control Data
Sheet or System Wide Control User’s Manual for details on how SWC works.
Vision-Net
Technical Assistance
A digital architectural control system for use with C21/EC21 dimmer racks.
C21/EC21 racks and dimmers require a minimum of maintenance and servicing.
For operation or technical assistance, please contact Strand Lighting or the local
Authorized Service Center serving your area. (www.strandlighting.com)
Page iii
C21/EC21 Series Dimmer Rack
Operations Manual
Page iv
Table of Contents
This manual describes the operation and setup of the dimmer rack. It does not
contain information about installing the rack. See the separate C21 (2-450173010) or the EC21 (2-450173-030) Dimmer Rack Installation Manual for detailed
information concerning installation and wiring of the dimmer rack, then go to
Section 3 - Programming the C21/EC21 Dimmer Rack starting on page 24 in this
manual for initial rack setup and, if necessary, see Section 4 - Basic
Troubleshooting starting on page 64 of this manual.
Section 1 - General ........................................................................ 6
Summary Specification.......................................................................................6
120V Dimmer Modules.......................................................................................8
230V Dimmer Modules.....................................................................................10
Rack Components............................................................................................13
Dimmer Modules ..............................................................................................14
Reporting Dimmer Modules ........................................................................14
Sinewave Dimmer Modules ........................................................................14
Fan Module.................................................................................................15
Rack Processor Housing ............................................................................16
Rack Processor Module ...................................................................................17
Power Supplies ................................................................................................17
Control Interconnection Card (CIC) ..................................................................17
Processor Configuration .............................................................................17
Startup........................................................................................................17
LED Status .......................................................................................................18
Rack Processor Housing LEDs ..................................................................18
Rack Processor Module LEDs....................................................................18
Dimmer Events ...........................................................................................19
After Startup ...............................................................................................19
Section 2 - Operational Features................................................ 20
Rack Configuration...........................................................................................20
Dimmer Configuration ......................................................................................20
Control Inputs .............................................................................................21
Safety Features................................................................................................21
System Wide Control (SWC)............................................................................22
Outlook.............................................................................................................22
Vision.Net.........................................................................................................22
Section 3 - Programming the C21/EC21 Dimmer Rack ............ 24
Controls and Displays ......................................................................................24
Key Lock ..........................................................................................................24
Using the Menu Keypad ...................................................................................25
The Status Log.................................................................................................25
Page 1
C21/EC21 Series Dimmer Rack
The Main Menu ................................................................................................26
Rack Identity Menu...........................................................................................27
Set Rack Name ..........................................................................................27
Set Rack Location ......................................................................................27
Set Main Breaker ID ...................................................................................27
View Serial Number....................................................................................28
View Dealer Info. ........................................................................................28
Set Date .....................................................................................................28
Set Time .....................................................................................................28
View Rack Size...........................................................................................29
View Software Version ...............................................................................29
Set Rack Unique ID ....................................................................................29
Network Config Menu.......................................................................................30
Set IP Address............................................................................................30
Set SubNet Mask........................................................................................30
Set Host Name ...........................................................................................31
Set Gateway IP...........................................................................................31
View MAC Address.....................................................................................31
Rack Config menu............................................................................................32
Review Module Types ................................................................................32
Set Module Type ........................................................................................32
Set Module Type Range.............................................................................32
Set Fan Control ..........................................................................................33
Set LCD Backlight ......................................................................................33
Set LCD Contrast .......................................................................................33
Set Keypad Lock ........................................................................................33
Set Active Processor ..................................................................................34
Enable Cable Comp. ..................................................................................34
Enable VoltLoss Comp. ..............................................................................34
Save Recovery Config................................................................................34
Restore Saved Config ................................................................................35
Change Pass Code ....................................................................................35
User Profile Menu.............................................................................................35
Set User Profile ..........................................................................................35
Dimmer Config Menu .......................................................................................36
Set Dimmer Patch ......................................................................................36
View Full Output V......................................................................................36
Set Full Output Volts...................................................................................37
View Regulation Mode................................................................................37
Set Regulation Mode ..................................................................................37
Set Circuit Names.......................................................................................38
Autonumber Circuit ID ................................................................................38
Load Profile Actions....................................................................................38
To Dimmer Dynamics Menu.............................................................................39
View Response Times................................................................................39
Set Response Times ..................................................................................39
View Profiles...............................................................................................40
Select Profiles.............................................................................................40
View Cut Levels..........................................................................................40
Set Cut Levels ............................................................................................41
Operations Manual
Page 2
View Minimum Levels.................................................................................41
Set Minimum Levels ...................................................................................41
View Cable Impedance...............................................................................42
Set Cable Impedance .................................................................................42
View Report Enables ..................................................................................42
Set Report Enables ....................................................................................42
View Trip Modes.........................................................................................43
Set Trip Modes ...........................................................................................43
Input Config Menu ............................................................................................44
Set DMX A Options ....................................................................................44
Set DMX A Label ........................................................................................44
Set DMXB Options .....................................................................................44
Set DMX B Label ........................................................................................45
Set Panic Options.......................................................................................45
Enable AV Port ...........................................................................................45
Enable SMX Sharing ..................................................................................48
Set SMX Sharing Group .............................................................................48
Enable SVN Sharing...................................................................................48
SWC Menu.......................................................................................................48
Call SWC Preset.........................................................................................49
Record SWC Preset ...................................................................................49
Set No Mux Preset .....................................................................................49
Set No Mux Hold Time ...............................................................................49
Set No Mux NetSlot ....................................................................................49
Set Fade Time ............................................................................................50
Set Fade Time Range ................................................................................50
Edit SWC Event List Editor .........................................................................50
Set Power-Up Preset..................................................................................50
Outlook Menu...................................................................................................51
Call Outlook Preset.....................................................................................51
Call Outlook Pr. Range...............................................................................51
Record Outlook Preset ...............................................................................51
Record Outlook Pr. Range .........................................................................51
Set Channel Levels ....................................................................................51
Set Ch. Levels Range.................................................................................51
Set Outlook Fade Time...............................................................................52
Set Fade Time Range ................................................................................52
Set Power-up Preset ..................................................................................52
Review Outlook Patch ................................................................................52
Set Outlook Patch.......................................................................................52
Set Outlook Defaults...................................................................................52
Local Control Menu ..........................................................................................53
Set Dimmer level ........................................................................................53
Set Dimmer Lev. Range .............................................................................53
Call SWC Preset.........................................................................................54
Call Outlook Preset.....................................................................................54
Status Reporting Menu.....................................................................................54
View Live Status .........................................................................................54
View Rack Status .......................................................................................55
View Event Log...........................................................................................55
Page 3
C21/EC21 Series Dimmer Rack
View Profile Stats .......................................................................................55
View Comm Stats .......................................................................................55
View System Up-Time ................................................................................56
Set Temperature Scale...............................................................................56
Set Level Display........................................................................................56
Set Event Config.........................................................................................56
Enable Load Errors.....................................................................................57
Factory Menu ...................................................................................................57
Set Rack Model ..........................................................................................57
Set Rack Backplane ...................................................................................58
Set Rack Mains ..........................................................................................58
Set Phase Config........................................................................................58
Set Rack Size .............................................................................................58
Set Rack Slot Order....................................................................................59
Set Rack Slot Usage ..................................................................................59
To Rack Calibration Sub-Menu...................................................................60
Set Phase Sense Trim................................................................................60
Set Phase Filters ........................................................................................60
Revert to Mfg. Config..................................................................................60
EEPROM Test Write...................................................................................61
EEPROM Test Read ..................................................................................61
View Serial Number....................................................................................61
Set Language .............................................................................................61
Set Project Name .......................................................................................61
Set Dealer Name ........................................................................................62
Set Dealer Contact .....................................................................................62
Set Dealer Extra Info. .................................................................................62
Reboot Rack...............................................................................................63
Hide Factory Menu .....................................................................................63
Section 4 - Basic Troubleshooting............................................. 64
General ............................................................................................................64
Control Signal Flow ............................................ Error! Bookmark not defined.
Section 5 – C21/EC21 Web Pages .............................................. 65
General ............................................................................................................65
Main Screen ...............................................................................................65
Web Page Authorization .............................................................................65
Web Page Setup ........................................................................................66
Web Page System Parameters ..................................................................67
Web Page System Construction.................................................................68
Web Page Construction Slots.....................................................................68
Web Page Dimmer Modules.......................................................................69
Web Page Dimmer Circuits ........................................................................70
Web Page Dimmer Dynamics.....................................................................71
Web Page Dimmer User Profiles................................................................71
Web Page Dimmer Tolerance ....................................................................72
Web Page Dimmer Reporting.....................................................................72
Web Page Dimmer Patch ...........................................................................73
Operations Manual
Page 4
Web Page Firmware Update ......................................................................73
Web Page Local Control.............................................................................74
Table of Figures
Figure 1 – C21/EC21 Series Dimmer Rack Fully Populated (doors removed).......13
Figure 2 – Dual Dimmer Module ............................................................................14
Figure 3 – Fan Housing .........................................................................................15
Figure 4 – Rack Processor Housing ......................................................................16
Figure 5 – Rack Processor Module........................................................................17
Figure 6 - Processor Module Front Panel ..............................................................18
Figure 7 - Rack Processor Module Front Panel .....................................................24
Page 5
C21/EC21 Series Dimmer Rack
Section 1 - General
Summary Specification
Dimmer Rack Specifications:
Capacity:
Large rack: 48 Dimmer Modules (dual, single or quad)
Mid-range rack: 36 Dimmer Modules (dual, single or quad)
Small rack: 24 Dimmer Modules (dual, single or quad)
Supply:
90 to 264VAC, 3-phase, neutral + earth (Delta on request),
47 to 63 Hz
Max Current (per
Large rack:
phase):
800 amps (120V markets), 800 amps (230V markets)
Mid-range rack:
800 amps (120V markets), 600 amps (230V markets)
small rack:
800 amps (120V markets), 400 amps (230V markets)
Dimensions:
Large rack: Height 80” (2032mm), Width 24.36” (619mm),
Depth, 23.62” (600mm)
Mid-range rack: Height 67” (1703mm), Width 24.36”
(619mm), Depth, 23.62” (600mm)
Small rack: Height 57” (1448mm), Width 24.36” (619mm),
Depth, 23.62” (600mm)
Weight:
Large rack: 300 lbs. (136 Kg) empty and 690 lbs. (310 Kg)
with all modules and electronics installed.
Mid-range rack: 270 lbs. (122Kg) empty and 662 lbs.
(300Kg) with all modules and electronics installed
Small rack: 240 lbs. (109Kg) empty and 512 lbs. (232Kg)
with all modules and electronics installed.
Busbar Rating:
50,000 AIC standard or 100,000 AIC optional
Control Circuit
Optical isolation between high voltage and control
Isolation:
electronics is 2500VAC. Control inputs are opto-isolated
from the processor at 2500VAC, offering double optical
isolation between the controller and high power circuits.
Storage Temp:
-40°C to 70°C
Operating Temp:
0°C to 40°C ambient
Storage Humidity:
0% to 95%, relative humidity, non-condensing
Operating Humidity: 10% to 95%, relative humidity, non-condensing
Note: All specifications are correct at the time of going to press. In
the interest of continuous product improvement Strand Lighting
reserves the right to change specifications without notice.
Operations Manual
Page 6
Dimmer Modules Specifications:
RCD (GFCI):
Circuit
protection:
Residual Current Device with circuit protection.
Appropriately sized fully magnetic or thermal/magnetic circuit
breaker of 10,000 AIC (15A, 20A, 50A & 100A @ 120V) or
50,000 AIC (15A, 25A & 50A @ 230V) fault current rating.
Output voltage: Maximum full load voltage loss measured at the dimmer rack is
3 volts. Maximum output voltage for each dimmer can be
limited through a software setting.
Load regulation: Dimmers will maintain their output within +/- 1% of the set output
with load changes from 1kW to the maximum rating of the
dimmer.
Line
The system regulates dimmer outputs to within 1V over
compensation: operating voltage range. Each dimmer is individually regulated.
Efficiency:
Minimum power efficiency for dimmers is 97% at full load.
Maximum full load dimmer loss is 3V RMS.
Contactor non-dim power efficiency is 99%.
DC component Less than 1 volt with tungsten loads from 60W to the maximum
of output:
rating of the dimmer, at all control levels.
Input response The response time (time between OFF and 100%) can be set to
time:
‘Fast’ (30msec), ‘Medium’ (100ms), ‘Slow’ (300ms), ‘Very Slow’
(700ms) or ‘Glacial (1000ms). The default is medium (100ms).
Note: All specifications are correct at the time of going to press. In
the interest of continuous product improvement Strand Lighting
reserves the right to change specifications without notice.
Page 7
C21/EC21 Series Dimmer Rack
120V Dimmer Modules
Operations Manual
The following dimmer & non-dim modules are currently available for the
120V markets:
No
Number
of Chans
Quad
Incan.
No
Dual
Incan.
Catalog #
Ampacity
Kw
Type
Reporting
Load
76550
10A
1.2kW
Basic
76551
15A
1.8kW
Basic
76552
15A
1.8kW
Standard
No
Dual
Incan.
76553
15A
1.8kW
Hi Rise
No
Dual
Incan.
76554
15A
1.8kW
Constant
No
Dual
Incan.
76555
15A
1.8kW
Nondim
No
Dual
Incan.
76556
15A
1.8kW
Basic
Yes
Dual
Incan.
76557
15A
1.8kW
Standard
Yes
Dual
Incan.
76558
15A
1.8kW
Hi Rise
Yes
Dual
Incan.
76559
15A
1.8kW
Constant
Yes
Dual
Incan.
76560
15A
1.8kW
Nondim
Yes
Dual
Incan.
76561
15A
1.8kW
Sinewave
Yes
Dual
Variety
76562
20A
2.4kW
Basic
No
Dual
Incan.
76563
20A
2.4kW
Standard
No
Dual
Incan.
76564
20A
2.4kW
Hi Rise
No
Dual
Incan.
76565
20A
2.4kW
Constant
No
Dual
Incan.
76566
20A
2.4kW
Nondim
No
Dual
Incan.
76567
20A
2.4kW
Basic
Yes
Dual
Incan.
76568
20A
2.4kW
Standard
Yes
Dual
Incan.
76569
20A
2.4kW
Hi Rise
Yes
Dual
Incan.
76570
20A
2.4kW
Constant
Yes
Dual
Incan.
76571
20A
2.4kW
Nondim
Yes
Dual
Incan.
76572
20A
2.4kW
Sinewave
Yes
Dual
Variety
76573
20A
2.4kW
Basic
No
Quad
Incan.
76574
50A
6.0kW
Basic
No
Single
Incan.
76575
50A
6.0kW
Standard
No
Single
Incan.
Page 8
76576
50A
6.0kW
Hi Rise
No
Number
of Chans
Single
76577
50A
6.0kW
Constant
No
Single
Incan.
76578
50A
6.0kW
Nondim
No
Single
Incan.
Catalog #
Page 9
Ampacity
Kw
Type
Reporting
Load
Incan.
76579
50A
6.0kW
Basic
Yes
Single
Incan.
76580
50A
6.0kW
Standard
Yes
Single
Incan.
76581
50A
6.0kW
Hi Rise
Yes
Single
Incan.
76582
50A
6.0kW
Constant
Yes
Single
Incan.
76583
50A
6.0kW
Nondim
Yes
Single
Incan.
76584
100A
12.0kW
Constant
No
Single
Incan.
76585
100A
12.0kW
Basic
No
Single
Incan.
76586
100A
12.0kW
Constant
Yes
Single
Incan.
76587
100A
12.0kW
Basic
Yes
Single
Incan.
76588
Blank
N/A
N/A
No
N/A
N/A
76589
N/A
2.4kW
Test Mod.
No
Dual
Incan.
76590
N/A
2.4kW
Test Mod.
No
Quad
Incan.
76591-0001
20A
2.4kW
Dim/Nondim
No
Dual
Incan.
76591-0002
20A
2.4kW
Nondim/Dim
No
Dual
Incan.
76591-0003
10A
1.2kW
Nondim
No
Quad
Incan.
76591-0004
15A
1.8kW
Nondim
No
Quad
Incan.
76591-0005
20A
2.4kW
Nondim
No
Quad
Incan.
76591-0006
15A
1.8kW
Basic
No
Quad
Incan.
C21/EC21 Series Dimmer Rack
230V Dimmer Modules
Operations Manual
The following dimmer & non-dim modules are currently available for the
230V markets:
Number
Load
of Chans
Quad
Tungsten
Catalog #
Ampacity
Kw
Type
Reporting
76600
13A
2.5kW
Basic
No
76601
16A
3.0kW
Standard
No
Dual
Tungsten
76602
16A
3.0kW
Standard
No
Dual
Tungsten
76603
16A
3.0kW
Standard
No
Dual
Tungsten
76604
16A
3.0kW
Hi-Rise
No
Dual
Tungsten
76605
16A
3.0kW
Hi-Rise
No
Dual
Tungsten
76606
16A
3.0kW
Hi-Rise
No
Dual
Tungsten
76607
16A
3.0kW
Standard
Yes
Dual
Tungsten
76608
16A
3.0kW
Standard
Yes
Dual
Tungsten
76609
16A
3.0kW
Standard
Yes
Dual
Tungsten
76610
16A
3.0kW
Hi-Rise
Yes
Dual
Tungsten
76611
16A
3.0kW
Hi-Rise
Yes
Dual
Tungsten
76612
16A
3.0kW
Hi-Rise
Yes
Dual
Tungsten
76613
25A
5.0kW
Standard
No
Dual
Tungsten
76614
25A
5.0kW
Standard
No
Dual
Tungsten
76615
25A
5.0kW
Standard
No
Dual
Tungsten
76616
25A
5.0kW
Hi-Rise
No
Dual
Tungsten
76617
25A
5.0kW
Hi-Rise
No
Dual
Tungsten
76618
25A
5.0kW
Hi-Rise
No
Dual
Tungsten
76619
25A
5.0kW
Standard
Yes
Dual
Tungsten
76620
25A
5.0kW
Standard
Yes
Dual
Tungsten
76621
25A
5.0kW
Standard
Yes
Dual
Tungsten
76622
25A
5.0kW
Hi-Rise
Yes
Dual
Tungsten
76623
25A
5.0kW
Hi-Rise
Yes
Dual
Tungsten
76624
25A
5.0kW
Hi-Rise
Yes
Dual
Tungsten
76625
50A
10.0kW
Standard
No
Single
Tungsten
76626
50A
10.0kW
Standard
No
Single
Tungsten
76627
50A
10.0kW
Standard
No
Single
Tungsten
76628
50A
10.0kW
Hi-Rise
No
Single
Tungsten
76629
50A
10.0kW
Hi-Rise
No
Single
Tungsten
76630
50A
10.0kW
Hi-Rise
No
Single
Tungsten
76631
50A
10.0kW
Standard
Yes
Single
Tungsten
Page 10
Page 11
Number
Load
of Chans
Single
Tungsten
Catalog #
Ampacity
Kw
Type
Reporting
76632
50A
10.0kW
Standard
Yes
76633
50A
10.0kW
Standard
Yes
Single
Tungsten
76634
50A
10.0kW
Hi-Rise
Yes
Single
Tungsten
76635
50A
10.0kW
Hi-Rise
Yes
Single
Tungsten
76636
50A
10.0kW
Hi-Rise
Yes
Single
Tungsten
76637
16A
3.0kW
Sinewave
Yes
Dual
Variety
76638
16A
3.0kW
Sinewave
Yes
Dual
Variety
76639
16A
3.0kW
Sinewave
Yes
Dual
Variety
76640
25A
5.0kW
Sinewave
Yes
Dual
Variety
76641
25A
5.0kW
Sinewave
Yes
Dual
Variety
76642
25A
5.0kW
Sinewave
Yes
Dual
Variety
76643
16A
3.0kW
Fluor
No
Single
Fluor
76644
16A
3.0kW
Fluor
No
Single
Fluor
76645
16A
3.0kW
Fluor
No
Single
Fluor
76646
16A
3.0kW
Nondim
No
Dual
Tungsten
76647
16A
3.0kW
Nondim
No
Dual
Tungsten
76648
16A
3.0kW
Nondim
No
Dual
Tungsten
76649
16A
3.0kW
Nondim
Yes
Dual
Tungsten
76650
16A
3.0kW
Nondim
Yes
Dual
Tungsten
76651
16A
3.0kW
Nondim
Yes
Dual
Tungsten
76652
25A
5.0kW
Nondim
No
Dual
Tungsten
76653
25A
5.0kW
Nondim
No
Dual
Tungsten
76654
25A
5.0kW
Nondim
No
Dual
Tungsten
76655
25A
5.0kW
Nondim
Yes
Dual
Tungsten
76656
25A
5.0kW
Nondim
Yes
Dual
Tungsten
76657
25A
5.0kW
Nondim
Yes
Dual
Tungsten
76658
16A
3.0kW
Constant
No
Dual
Tungsten
76659
16A
3.0kW
Constant
No
Dual
Tungsten
76660
16A
3.0kW
Constant
No
Dual
Tungsten
76661
16A
3.0kW
Constant
Yes
Dual
Tungsten
76662
16A
3.0kW
Constant
Yes
Dual
Tungsten
76663
16A
3.0kW
Constant
Yes
Dual
Tungsten
76664
25A
5.0kW
Constant
No
Dual
Tungsten
76665
25A
5.0kW
Constant
No
Dual
Tungsten
76666
25A
5.0kW
Constant
No
Dual
Tungsten
C21/EC21 Series Dimmer Rack
Operations Manual
Catalog #
Ampacity
Kw
Type
Reporting
76667
25A
5.0kW
Constant
Yes
76668
25A
5.0kW
Constant
Yes
Number
Load
of Chans
Dual
Tungsten
Dual
Tungsten
76669
25A
5.0kW
Constant
Yes
Dual
Tungsten
76670
16A
3.0kW
Test Mod
No
Dual
Tungsten
76671
16A
3.0kW
Test Mod
No
Dual
Tungsten
76672
16A
3.0kW
Test Mod
No
Dual
Tungsten
76673-0001
20A
4.0kW
Hi-Rise
Yes
Dual
Tungsten
76673-0002
20A
4.0kW
Nondim
Yes
Dual
Tungsten
76673-0003
13A
2.5kW
Nondim
No
Quad
Tungsten
76673-0004
16A
3.0kW
Fluor
Yes
Single
Fluor
76673-0005
16A
3.0kW
Fluor
Yes
Single
Fluor
76673-0006
16A
3.0kW
Fluor
Yes
Single
Fluor
Page 12
Rack Components
The C21/EC21 dimmer rack is a listed, free standing, factory assembly of welded
steel and aluminum construction finished in a fine textured, scratch resistant
coating.
Each C21/EC21 dimmer rack consists of a rack processor housing (RPH) with one
or two rack processor modules (RPM), a fan module, and up to 24, 36 or 48
dimmer modules. The dimmer connectors at the back of the rack provide for load
wire connection. Main bus bars are provided for line wire connections. An earth
ground lug is provided in the rack. The dimmer connectors in the rack are
polarized to prevent dimmer modules being plugged into the different ampacity
slots. The dimmer racks can be individually fed or bused together using an
optional busing kit.
Large dimmer racks have provision for up to 48 dimmer modules. Mid-range
dimmer racks have provision for up to 36 dimmer modules. Small dimmer racks
have provisions for up to 24 dimmer modules. Dimmer modules contain one, two
or four dimmers, and dimmer module types can be mixed within a rack in various
combinations.
Door Hinge
Bracket
Ventilation Grill
Dimmer Modules
Door Strike
Fan Housing
Rack Processor
Housing
Rack Processor
Module
Backup Processor
Module (Optional)
Blank Panel
Figure 1 – C21/EC21 Series Dimmer Rack Fully Populated (doors removed)
Page 13
C21/EC21 Series Dimmer Rack
Dimmer Modules
The power modules are the high power switching section of the C21/EC21
dimming system. The power block in this module is the interface between the high
power AC and low power control. It is driven by low level signals (5mA, 3-24V) and
switches high level signals (up to 100A, 120/240VAC). High specification filtering,
SCR dimming, contactor non-dims, Sinewave dimming, and load status reporting
electronics are available as options. Dimmers can be mixed in any combination in
a rack. This lets you use the exact dimmer type needed for each circuit.
Quad dimming modules are also available in custom racks.
Power modules are constructed from aluminum, folded to form three sides of the
dimmer and to support the dimmer connector and heatsink. The fourth side of the
dimmer is formed by the heatsink. The top and bottom of the dimmer are open for
cooling.
A sturdy handle is provided below the circuit breakers.
An optional mechanical locking bar on the dimmer tray secures the dimmers in the
rack.
Chokes
Connector
Circuit Breakers
Dimmer Wing
With Type & Rating
Handle
Reporting PCB
(optional)
SSR or SCR Pack
Chassis
Figure 2 – Dual Dimmer Module
Reporting Dimmer Most C21/EC21 dimmer modules are available in load status reporting versions.
Modules Load status reporting versions of dimmers can be mixed in any combination with
standard dimmers in C21/EC21 racks. These dimmers report many dimmer status
items back to the processor. The information can be accessed through various
menu items. The processor can then display a wide range of faults and diagnostic
data.
Each Reporting dimmer module contains a temperature sensor which will shut it
down if it overheats. Anything causing overheating in the rack will cause a gradual
shutdown as each Reporting dimmer module overheats.
Sinewave Dimmer C21 Sinewave dimmers provide a fully symmetrical sinewave at any output voltage
Modules setting eliminating all lamp noise and reducing reflected harmonics on the building
power supply. Sinewave dimmers control a wide variety of loads including
dimmable electronic ballasts, LED’s, motors and conventional incandescent lamps.
C21 and EC21 sinewave dimmer modules have microprocessor controlled overcurrent and short circuit protection and will automatically shut down if necessary.
Operations Manual
Page 14
Resetting the dimmer to zero percent (0%) from the control system will restore
operation in the event of a module shutdown.
Make sure that the neutral wire is landed correctly with its corresponding
load wire for proper operation (see the C21 or EC21 Installation manual for
more information). Failure to do so will cause the dimmer module to shut
down.
Warning
Since the sinewave dimmer module monitors the dimmer rack power feed at
all times, it is imperative that the power feed is clean and free of any
distortion.
In the presence of poor quality power with significant mains disturbances the
Sinewave dimmer module may shut down to protect the IGBT power devices.
Fan Module The dimmer racks are cooled by a set of three low noise variable speed fans in a
fan module at the bottom of the rack. The cooling system is designed to let the rack
continue functioning if any one of the three fans fail. Cooling air is pushed up
through the dimmer stack and exhausted through venting at the top of the rack.
These fans are for dimmer cooling only, and can be set to fixed or variable speeds.
The fixed speed fan setting is for situations where changes in ambient noise are a
problem. With this setting, the fans are always ON when the dimmer rack is in
operation.
The variable speed fan setting minimizes noise and maximizes fan life. With this
setting, the fan speed is adjusted so that fans reach full when 24 dimmers are at
full, or equivalent (e.g., 48 dimmers at 50%). Increases in fan speed take 1 minute
with this setting, while decreases in fan speed take 5 minutes. Fans are turned
OFF when no dimmers are in use.
Warning
C21 or EC21 dimmer racks sold with Sinewave dimmers require an additional
fan housing located at the top of the dimmer rack. The additional fan
housing doubles the overall dB level.
Fan
Module
Grill
Filter
Figure 3 – Fan Housing
Page 15
C21/EC21 Series Dimmer Rack
Rack Processor Housing Each C21/EC21 dimmer rack contains a rack processor housing (RPH) with all of
the control electronics for the rack. This RPH contains the processor module(s)
(RPM), control station power supplies, and control interconnection card (CIC) for
the rack, and is shipped separately from the rack to minimize the possibility of
damage.
This chassis can be equipped with one or two processor modules. The second
processor module acts as a backup. The configuration data from either processor
can be transferred into the other processor. The currently inactive processor
always tracks the currently active processor.
Power
Supplies
Backup
Processor
Module
Control
Interconnection
Card (CIC)
Rack Processor
Module (RPM)
Figure 4 – Rack Processor Housing
Operations Manual
Page 16
Rack Processor Module
Each C21/EC21 rack contains one or two rack processor modules (RPM). Each
processor module has a backlit LCD display, a 7 key keypad, and 6 LEDs to report
processor module and dimmer status and allow setup and control at the rack. In
normal operation, this display normally shows the rack name and the OK message.
If there are any rack or dimmer events reported, the display will show error
messages.
Pressing the < or > keys will takes you into a series of setup menus to view and set
up the more frequently used C21/EC21 features. See Section 3, Processor Module
Programming for details on accessing these functions.
All programmed data is held in battery maintained RAM for up to 6 months without
power.
Figure 5 – Rack Processor Module
Power Supplies
Control Interconnection
Card (CIC)
Each C21/EC21 rack can have up to three power supplies, depending on the
accessories provided. These power supplies are mounted on the rack processor
housing.
The electronics chassis also contains the control interconnection card (CIC). This
is where the contractor terminates all control wiring for the rack. All control terminal
strips are 2-part plug-in strips so that the electronics chassis can be easily
removed from the rack.
Processor Configuration Once you have applied power you need to make sure that the system is working
correctly and the processor modules are set properly for the installation. This step
checks for any problems due to shipping or installation.
Startup When the rack is switched ON, a number of self-tests are run. The system displays
the rack name.
Strand Lighting
Rack 1
xxxV xxxV xxxV
xxhz xxhz xxhz
< or > to select menu
Page 17
C21/EC21 Series Dimmer Rack
When the self-tests are complete the PROCESSOR OK LED on the front of the
processor module will turn ON, and the default text will show on the LCD display.
Status LED’s
LCD
Control Keypad
NETWORK CONNECTION
DMX512 RDM PORT A
DMX512 PORT B
PROCESSOR OK
MODULE EVENT
ACTIVE PROCESSOR
Figure 6 - Processor Module Front Panel
If the MODULE EVENT LED is ON, check the dimmer event log to see
which dimmer is causing problems. If any other LED does not
illuminate correctly, switch OFF the power immediately and check
the installation again. If all wiring seems correct, call Strand Lighting
or your local Authorized Service Center.
LED Status
The LEDs on the front of each rack processor module are the first level of
diagnostics and provide immediate visual status indication. The nine LEDs on the
front of the rack processor housing and module indicate the following:
Rack Processor Housing Phase A (green):
LEDs Phase B (green):
Phase C (green):
Over-Temp (red):
Panic (red):
Lighthouse (blue):
Should be ON if PhaseA/Line1 is OK.
Should be ON if Phase B/Line 2 is OK.
Should be ON if PhaseC/Line 3 is OK.
Should be OFF. Flashing indicates an Over-Temp
condition. ON indicates dimmer module automatic
Over-Temp shutdown.
Should be OFF. On indicates that PANIC has
Been activated.
Blue = normal. Flashing red = error. Solid red = shutdown.
Rack Processor Module Network Connection (green):
LEDs DMX A (green):
DMX B (green):
Module Event (red):
Processor OK (green):
Active Processor (green):
Operations Manual
Should be ON if there is a network signal.
Should be ON if there is a DMX signal.
Should be ON if there is a DMX signal.
Should be OFF. On indicates a dimmer fault
Should be ON. Off indicates there is a problem.
Should be ON if self-test is OK. Indicates active
processor.
Page 18
Dimmer Events If the Module Event LED is on, the LCD will show the number of dimmer events at
which time the display can be manually accessed to show a description of the
event(s). Refer to the appendices section of this manual for a description of event
codes. If any other LED does not illuminate correctly, switch OFF the power
immediately and check the installation again. If the fault persists and all wiring
seems correct, call Strand Lighting or your local Authorized Service Center
(www.strandlighting.com).
After Startup 1. Check the following items to make sure they are correctly set in the processor
2.
3.
module:
• Rack type (see Rack Config Menu in section 3, Front Panel
Programming)
• Phasing (see Rack Config Menu in section 3, Front Panel Programming)
• Starting multiplex signal number and dimmer protocol (see Patching Menu
in section 3, Front Panel Programming)
• Input Voltage (see Rack Config Menu in section 3, Front Panel
Programming)
• Dimmer numbering (see Rack Config Menu in section 3, Front Panel
Programming)
Other items you may wish to check at this time, depending on your system
configuration, are:
• Mux patch (see Patching Menu in section 3, Front Panel Programming)
• Outlook patch (see Patching Menu in section 3, Front Panel
Programming)
• Max Voltage (see Rack Config Menu in section 3, Front Panel
Programming)
• Min Level (see Rack Config Menu in section 3, Front Panel Programming)
Switch on all load circuit breakers.
Connect a suitable luminaire to each outlet and check every dimmer using the
SET LEVEL control facility, a suitable control console, or an SWC hand held
controller. Investigate and correct any malfunctions you find.
If any dimmers do not work, stop and check the slot type for the dimmer.
Dimmers will not work properly if their slot type is incorrectly assigned.
Make sure that all of the modules are in their correct slots, and that the slot
type for each dimmer is correctly set in the processor module.
5.
Page 19
Install the fan screens, door, to complete the system installation.
C21/EC21 Series Dimmer Rack
Section 2 - Operational Features
Rack Configuration
The following configuration items are usually programmed during commissioning,
but can also be reprogrammed by the user.
ƒ
ƒ
ƒ
ƒ
ƒ
ƒ
ƒ
ƒ
ƒ
ƒ
ƒ
ƒ
ƒ
Dimmer Configuration
Rack name.
Panic selection and configuration
Maximum output voltage (per dimmer): 20-250 volts (e.g. set to 105V for
extended lamp life).
Minimum level (per dimmer): 0% - 100% (e.g. set to 10% for aisle lights or
large lamp preheat).
Room and channel Patching (for applications using Outlook)
Each dimmer can be patched to any valid DMX512 address number for the
standard input A (DMX A), input B (DMX B) or network.
Circuit ID—used by SWC and status reporting software.
Record and recall presets (1-8, ON and OFF per room for Outlook control, and
0-128 per rack for System Wide Control).
Define Preset Number or “Hold” condition on DMX failure.
Define power-up preset per rack for Outlook architectural presets.
Set LCD contrast.
Error log accessible from the processor module or status reporting software.
Individual dimmer reporting enable/disable.
Configuration items associated with the dimmer module can be set from the
processor module front panel.
ƒ
ƒ
The output response profile can be set to Linear, Square, S-Curve, FluoElectric (for electronic fluorescent ballasts), Fluo-Magnetic (for magnetic
fluorescent ballasts), and Non-Dim. The two fluorescent settings let you set
the top end voltage and the bottom end cutoff voltage. The Non-Dim setting
lets you set the turn-on threshold for the non-dim. Five additional user
programmable profiles are available through the Set Rack Configuration menu
or from the optional status reporting software.
Dimmer response (per dimmer): fast (30ms), normal (100ms), slow (300ms),
very slow (700ms) or Glacial (1000ms). This determines a dimmer’s rate of
response to a change in control level. Slow is usually set for large tungsten
loads to reduce filament inrush, medium or fast for small loads.
Do not use ‘fast’ for sinewave dimmers or lamps that are 5kW or higher.
120V Sinewave dimmers must be set to 300ms for proper operation.
230V-3kW Sinewave dimmers must be set to 300ms for proper operation.
230V-5kW Sinewave dimmers must be set to 700ms for proper operation.
Warning
ƒ
ƒ
Operations Manual
Dimmer control assignment (per dimmer) to the “combined” levels of Outlook
preset, SWC preset, Vision-Net, DMX A, DMX B, Network or to a fixed level
(0% - 99% or “Full”). The way in which the various input levels combine is also
determined on a per dimmer basis by setting the dimmer DMX mode.
A special smoothing algorithm is applied to small level changes to maintain
smooth fades with long fade times.
Page 20
Control Inputs The Control Interconnection Card, or CIC, is the printed circuit board on which all
contractor control wiring connections are made. It is located on the top of the Rack
Processor Housing (RPH) and contains:
ƒ
An optional Ethernet switch, which connects to a Strand ShowNet system and
is Advanced Network Control (ACN) ready. This switch allows for easy
connections between dimmer racks. It also connects to the network
receptacle located in the upper left rear of the dimmer rack.
ƒ
Two optically isolated DMX512 control inputs. Both inputs can be configured
as a DMX512 input, DMX512 output, Strand Lighting’s System Wide Control
(SWC) dimmer protocol, Strand Lighting’s Outlook architectural protocol and
Strand Lighting’s Vision-Net architectural protocol. Each DMX input has a
patch to allow overlapping or separation of any DMX control level.
ƒ
Six optically isolated contact inputs, for:
ƒ
Pin
Function
Type
Description
1
PANIC ON
Momentary
Turns Panic On
2
PANIC OFF
Momentary
Turns Panic Off
3
FIRE ALARM
Maintained
Turns Panic On, No Override
4
SWC PRESET 1
Momentary
Fires SWC Preset 1
5
GO NEXT SWC
Momentary
Fires “Next” SWC Preset
6
GO SWC OFF
Momentary
Fires SWC Preset 0 (Blackout)
7
Com/Gnd
Com/Gnd
8
Com/Gnd
Com/Gnd
An Audio Visual Interface port. This serial input will support connection to
an external A/V or show control system that supports an RS232 serial
connection.
ƒ 96 or 192 panic select switches
Safety Features
In order to minimize the impact of failures to any part of C21/EC21 series dimmer
racks, a number of security features, some of which are optional, are provided.
Standard safety features for C21/EC21 series dimmer racks are:
ƒ
ƒ
ƒ
ƒ
ƒ
ƒ
ƒ
ƒ
ƒ
Page 21
Convection cooling of all components with fan assist.
Three fans located at the bottom of the rack (an additional fan housing is
added when Sinewave dimmers are added).
Module over-temperature shutdown (Reporter modules only).
The processor module can be set to hold the last dimmer levels forever,
or to fade to a specified SWC preset after a preset interval in cases of
DMX signal failure.
Setup data is stored in non-volatile RAM.
2500V optical isolation of DMX A and DMX B inputs, SWC, Outlook
communication.
All, or selected dimmers in a rack can be set to either Off or full On when
the external Panic button is pressed.
Automatic Panic on removal of processor module. In racks with two
processor modules, both modules must be removed to activate Panic.
Keypad lock.
C21/EC21 Series Dimmer Rack
Optional safety features for C21/EC21 series dimmer racks include:
ƒ
ƒ
Redundant tracking backup (requires a second processor module fitted to
the rack). The backup processor automatically tracks the master
processor and takes over control of the dimmer rack on failure of the
master processor.
Status reporting software that lets you store setup data off-line.
System Wide Control
(SWC)
SWC lets you control multiple C21/EC21 series dimmer racks from a single
location. A hand held controller lets you program and recall all 128 presets, and
control individual dimmers. 8 and 16 channel push-button stations let you record or
recall any 8 or 16 of the 128 presets at each station. An audiovisual interface is
also available to activate presets from external contacts. Contact Strand Lighting or
see the System Wide Control User’s Manual for details on how SWC works.
Outlook
Outlook is a comprehensive family of control stations designed for architectural
applications needing a simple, flexible control solution with minimal installation and
cabling costs. These control stations can access, modify, and recall lighting levels
stored in the rack processor module. Outlook control station features and options
include:
ƒ
ƒ
ƒ
ƒ
ƒ
ƒ
ƒ
ƒ
ƒ
Vision.Net
Vision.Net is a comprehensive family of control stations designed for architectural
applications needing a simple, flexible control solution with minimal installation and
cabling costs. These control stations can access, modify, and recall lighting levels
stored in the rack processor module. Vision.Net control station features and
options include:
ƒ
ƒ
ƒ
ƒ
ƒ
ƒ
ƒ
ƒ
ƒ
ƒ
Operations Manual
Control up to 16 separate rooms, with up to 15 channels per room
8 preset scenes plus ON and OFF for each room
Manual sliders (3, 6, 9, or 15 sliders per station) for direct control of
individual circuits
Record facility for saving slider levels for future push-button recall
Programmable fade times between 0 and 4 minutes from Outlook control
stations or 0 to 10 minutes from the processor module or status reporting
software
Record lockout facility for playback-only operation
1, 4, and 8 preset push-button stations
Audio-visual interface
Room combine stations for room partitioning
Control up to 255 separate rooms, with up to 125 channels per room
32 preset scenes available for each room
Manual sliders (3, 6, 9, or 15 sliders per station) for direct control of
individual circuits
Record facility for saving slider levels for future push-button recall
Programmable fade times between 0 and 60 minutes from Vision.Net
control stations
Record lockout facility for playback-only operation
Preset stations available from 1-button up to 8-buttons
Audio-visual interface
Room combine stations for room partitioning
Photo sensor and motion sensor
Page 22
Page 23
C21/EC21 Series Dimmer Rack
Section 3 - Programming the C21/EC21 Dimmer Rack
Controls and Displays
You can access the range of C21/EC21 series dimmer rack programmable
features using the Rack Processor Module keypad and 21 character, 8 line display.
Menus are shown in English.
Status LED’s
LCD
Control Keypad
NETWORK CONNECTION
DMX512 RDM PORT A
DMX512 PORT B
PROCESSOR OK
MODULE EVENT
ACTIVE PROCESSOR
Figure 7 - Rack Processor Module Front Panel
The control buttons let you scan through the various menus and options and set
the programmable features of the C21/EC21 series dimmer rack.
Key Lock
To avoid accidental or unauthorized use of the keys, you can lock the keypad.
When the Key Lock option is enabled, the processor keys are locked automatically
after 10 minutes with no keyboard input. When disabled, the keys are unlocked.
The factory default setting for this option is disabled. When locked, a key symbol is
displayed on the lower-right side of the default display.
To temporarily unlock the keys
Press and hold
e and o simultaneously for at least 2 seconds.
Unless the Set Processor Key Lock option is disabled, the keys will again lock after
10 minutes of no key activity.
Operations Manual
Page 24
Using the Menu Keypad
The default display appears if no keys are pressed for 10 minutes, unless one or
more error conditions have occurred. If more than one error has occurred, they are
displayed continuously in sequence.
+ -
or to cycle through the status menu, which shows a summary of the
Press
main rack statistics.
In general the rack processor keys do the following:
<
>
+
o
e
a + < or a + >
Moves to the next menu or moves the cursor to the next digit of a field.
Moves to the next menu or moves the cursor to the next digit of a field.
Increases the value of a digit or field.
Decreases the value of a digit or field.
Selects a menu or sub-menu. It is also pressed to accept changes when fields are
edited.
Returns the display to the previous menu level. Most configuration changes will
not take effect until the escape button has been pressed.
Selects a character group: numbers, capitol letters or lower-case letters.
A<
+ keys are pressed while editing a text field, the text will return to the
If the
previous unedited text.
Note: The blank “space” symbol is located under the numbers
character group.
A + + or a + -
The Status Log
Sets the maximum value for a field.
The Status Log lets you quickly check the status of the rack, using the
keys to display each parameter in turn.
+ or -
If one or more error conditions occur, the status display automatically shows the
Error Log, if a Dimmer Event occurs, the Event Log is automatically displayed,
Multiple errors or events are auto-scrolled.
The Status log for each rack, lists the rack number and software version number,
together with the error code and description of the error.
Note: When the backup and main processor are functioning, both displays should
show “Tracking.” When the system is properly tracking, data is continuously copied
from the “Enabled” processor (Master) to the “Disabled” processor (Backup).
Phase current will always be 0 (zero) on the backup processor.
The Status Log will return to the default display 5 seconds after the last key press.
Page 25
C21/EC21 Series Dimmer Rack
The Main Menu
The main menu lets you access all the other menus for configuring C21/EC21
series dimmer racks.
To access the main menu
From any of the status displays, Press
< or >
To return to the main menu
Press
E
Note: If no dimmer event is registered, returning from the main menu
brings you back to the display from which you called the main menu. If a
dimmer event is registered you will return to the dimmer events display.
Operations Manual
Page 26
Rack Identity Menu
The Rack Identity menu allows you to configure the following settings for the
dimmer rack:
To Main Menu
From Main Menu
To Rack Identity
Menu Items
Set Rack Name View or edit the name of the dimmer rack in this text field. The rack name is
displayed on the second line of the display.
To
Rack Identity
Menu
Set Rack Location View or edit the location of the dimmer rack in this text field.
To
Rack Identity
Menu
Set Main Breaker ID View or edit the name or location of the main breaker in this text field.
To
Rack Identity
Menu
Page 27
C21/EC21 Series Dimmer Rack
View Serial Number Allows you to view the C21/EC21 Processor serial number. The serial number is
entered by the factory and should not be changed in the field.
To
Rack Identity
Menu
View Dealer Info. Allows you to view the Dealer Information text field. The information for this text
field is entered within the Factory Menu section.
To
Rack Identity
Menu
Set Date Allows you to view or edit the date field.
Format: MM/DD/YY
To
Rack Identity
Menu
Set Time Allows you to view or edit the time field.
Format: 24-hour (HH:MM:SS)
To
Rack Identity
Menu
Operations Manual
Page 28
View Rack Size Allows you to view the rack size (slot and dimmer count). The rack size is set in
the Factory Menu section.
Default: 48 slot 96 Dims
To
Rack Identity
Menu
View Software Version Allows you to view the current software version of the rack processor.
To
Rack Identity
Menu
Set Rack Unique ID Allows you to set the Rack ID number. The default number is set at the factory and
must be changed to reflect the programming of Vision.Net rack numbers within
Vision.Net Designer software.
To
Rack Identity
Menu
C21 PROCESSO
R
C21 PROCESSO
R
Rack I dent i t y M
enu
Rack Uni que I D:
Rack_Name
Set Rack Uni que I D
Page 29
Rack_Name
>
04506
C21/EC21 Series Dimmer Rack
Network Config Menu
The Network Config menu allows you to configure the following settings for the
network settings of the dimmer rack:
To Main Menu
From Main Menu
To Network Config
Menu Items
Set IP Address Allows you to enter the IP address for the rack processor.
The default IP address is: 192.168.0.72
Note: Every rack processor is set to this default IP address. Make sure
you create a unique number for each dimmer rack in the system prior to
adding the racks to the network.
To
Network Config
Menu
C21 PROCESSO
R
C21 PROCESSO
R
Net wor k Conf i g Menu
I P Addr ess:
Rack_Name
Set I P Addr ess
Rack_Name
>192. 168. 0. 72
Set SubNet Mask Allows you to set the SubNet Mask for the rack processor.
The default SubNet Mask is: 255.255.255.0.
Note: The default subnet Mask should not be changed unless instructed to
do so by Strand Lighting.
To
Network Config
Menu
Operations Manual
Page 30
Set Host Name Allows you to set the Host Name for the processor.
Enter a unique name for the rack processor in this text field.
Note: This field is node name seen on the network and is different than the
dimmer rack name created in the Rack Identity Menu.
To
Network Config
Menu
Set Gateway IP Allows you to set the Gateway IP address for the processor.
The default Gateway IP is: 0.0.0.0
Note: The default Gateway IP address should not be changed unless
instructed to do so by Strand Lighting.
To
Network Config
Menu
View MAC Address Allows you to view the MAC Address assigned to the C21 and EC21 processor.
The MAC address is set at the factory is not accessible.
To
Factory
Menu
C21 PROCESSO
R
C21 PROCESSO
R
Net wor k Conf i g Menu
Vi ew M
AC Addr ess:
Rack_Name
Vi ew M
AC Addr ess
Page 31
Rack_Name
>00: E0: 01: 01: 11: 9A
C21/EC21 Series Dimmer Rack
Rack Config menu
Rack Config Menu allows you to set the configuration of the dimmer rack.
To Main Menu
From Main Menu
To Rack Config
Menu Items
Review Module Types Allows you to review the dimmer module type (00 through 99) assigned to the
dimmer slots, 6 dimmers at a time.
To
Rack Config
Menu
Set Module Type Allows you to set a single dimmer module type (based on the module part number)
for each rack slot.
See Section 1 to view a list of the dimmer module types for the 120v and 230v
markets.
To
Rack Config
Menu
Set Module Type Range Allows you to set the module type (based on the module part number) for a range
of dimmer rack slots.
See Section 1 to view a list of the dimmer module types for the 120v and 230v
markets.
To
Rack Config
Menu
Operations Manual
Page 32
Set Fan Control Allows you to adjust the minimum fan speed.
To
Rack Config
Menu
C21 PROCESSO
R
C21 PROCESSO
R
Rack Conf i g M
enu
Mi ni mum Fan Speed:
Rack_Name
Set Fan Cont r ol
Rack_Name
> %000
Set LCD Backlight Allows you to view or edit the LCD backlight.
To
Rack Config
Menu
Set LCD Contrast Allows you to view or edit the LCD Contrast.
To
Rack Config
Menu
Set Keypad Lock Allows you to enable or disable to keypad lockout.
The C21 processor incorporates a safety system to lock out the processor keys to
prevent tampering by unauthorized personnel. When the keys are locked, a key
symbol is displayed on the right-hand side of the LCD on the default display only.
Under this condition, the keys are inoperable unless you press the e and o keys
simultaneously, and hold them for about two seconds to release the lock. When
enabled, the key lock will automatically lock the keys if no keys are pressed for a
period of ten minutes.
When disabled, the keys are always unlocked.
When set to enabled, keys are not locked and the key lock symbol is not displayed
on the default display until ten minutes after the last key is pressed.
To
Rack Config
Menu
Page 33
C21/EC21 Series Dimmer Rack
Set Active Processor Allows you to select which processor, main or backup, will be active.
To
Rack Config
Menu
Enable Cable Comp. Allows you to enable or disable cable compensation.
To
Rack Config
Menu
C21 PROCESSO
R
C21 PROCESSO
R
Rack Conf i g M
enu
Cabl e Com
pensat i on:
Rack_Name
Enabl e Cabl e Comp.
Rack_Name
>Enabl ed
Enable VoltLoss Comp. Allows you to enable or disable voltage loss compensation.
To
Rack Config
Menu
C21 PROCESSO
R
C21 PROCESSO
R
Rack Conf i g M
enu
Vol t LossCom
pensat i on:
Rack_Name
Enabl e Vol t Loss Comp.
Rack_Name
>Enabl e
Save Recovery Config Allows you to save the current processor configuration as a recovery file on the
Control Interconnection Card (CIC) or to the flash RAM.
To
Rack Config
Menu
Operations Manual
Page 34
Restore Saved Config Allows you to restore the saved configuration file from the Control Interconnection
Card (CIC) or from the flash RAM .
To
Rack Config
Menu
Change Pass Code Allows you to create a 4-digit pass code for secured menu items.
Note: The Default pass code of ‘2606’ is always enabled and cannot be changed.
To
Rack Config
Menu
User Profile Menu
User Profile Menu allows you to view and create the five user-defined dimming
curves.
To Main Menu
From Main Menu
To User Profiles
Menu Items
Set User Profile Allows you to view or edit five user-defined dimmer profiles (dimming curves) that
may be applied using the Select Profiles function under the Dimmer Config menu.
You can set the input and output values for up to 100 steps for each user profile.
To
User Profile
Menu
Page 35
C21/EC21 Series Dimmer Rack
Dimmer Config Menu
Dimmer Config Menu allows you to set the configuration the dimmer modules and
the priority of the discrete signals.
To Main Menu
From Main Menu
To Dimmer Config
Menu Items
Set Dimmer Patch Allows you to assign ranges of dimmers to listen to net-slots at various priority or
HTP levels.
Note: Below are the four default patches.
001
002
003
004
005
Dimmers
001-96
001-96
001-96
001-96
Nslot
00001
02001
03001
19001
Pri
00h
01h
02h
00
*******
*****
***
Column #1
Lists the number of the patch
Column #2 - Dimmers
Lists the range of dimmers assigned to the patch.
Column #3 - Nslot (Netslot)
Lists the start number of the range
Column #4 - Pri (Priority)
Lists the priority number and if it is assigned as HTP
Note: By default all 192 possible dimmers are assigned. Generally this
number will reflect the actual number of dimmers in the rack.
To
Dimmer Config
Menu
View Full Output V. Allows you to view the Maximum output voltage of the dimmers, six at a time.
To
Dimmer Config
Menu
Operations Manual
Page 36
Set Full Output Volts Allows you to set the Maximum output voltage for any range of dimmers in the
rack. For instance, you can set the maximum voltage lower than the rated voltage
of your lamps for improved lamp life. If you have lamps or other equipment which
operate at a lower line voltage, you can set the output from the mdimmer to an
appropriate voltage for the devices.
The maximum output voltage is applied to all dimmers and dimmers assigned as
non-dims. It is not applied to contactor non-dims. You cannot use contactor nondims for devices which need a maximum output voltage setting.
Note: This function sets the dimmer output voltage, not the maximum
control level applied to the dimmer.
Caution: Be careful when using a maximum output voltage with dimmers set for
PANIC. When panic is activated, full output voltage appears at the output of any
dimmer or non-dim set for PANIC, regardless of how the maximum output voltage
is set.
To
Dimmer Config
Menu
View Regulation Mode Allows you to view the dimming curve assigned to a range of dimmers, 6 dimmers
at a time.
To
Dimmer Config
Menu
Set Regulation Mode Allows you to set the Regulation Mode for a range of dimmers.
These options are:
SiUnr = SineWave dimmer unregulated
SiReg = SineWave dimmer regulated
N-Dim = Non-Dim
ThUnr = Thyristor dimmer unregulated
ThReg = Thyristor dimmer regulated
To
Dimmer Config
Menu
Page 37
C21/EC21 Series Dimmer Rack
Set Circuit Names Allows you to view or edit the Circuit ID number for individual dimmers.
To
Dimmer Config
Menu
Autonumber Circuit ID Allows you to automatically assign sequential circuit ID numbers to the dimmers.
To
Dimmer Config
Menu
Load Profile Actions Allows you to learn, erase load profiles.
Options are:
None
Erase Load Profile
Learn Load Profile
Abort Profile Learn
To
Rack Config
Menu
C21 PROCESSO
R
C21 PROCESSO
R
Di mm
er Conf i g M
enu
Load Pr of i l e Act i on:
Rack_Name
Load Pr of i l e Act i ons
Operations Manual
Rack_Name
>None
Page 38
To Dimmer Dynamics
Menu
To Dimmer Dynamics Menu
View Response Times Allows you to view the response times for the dimmers, 6 dimmers at a time.
To
Modify Load
Profiles
To
Dimmer Config
Menu
Set Response Times The response time of a dimmer is the rate at which it responds to increases or
decreases in the control level. C21/EC21 dimmer racks provide five response
times:
Fast = 30ms
Normal = 100ms
Slow= 300ms
Very Slow = 700ms
Glacial = 1000ms
These options can be applied to a single dimmer or a range of dimmers. Slow is
generally used for large lamp loads, while fast is used for smaller lamp loads that
might be used in a chase effect.
Note: The ‘fast’ setting, together with the accuracy of digital dimmers can cause
very high inrush currents to flow. These may damage large lamp filaments and
cause circuit breakers to trip. Only set dimmers to ‘fast’ if necessary for a
particular effect.
Do not use ‘fast’ for sinewave dimmers or lamps that are 5kW or higher.
Note:
120V Sinewave dimmers must be set to 300ms for proper operation.
230V-3kW Sinewave dimmers must be set to 300ms for proper operation.
230V-5kW Sinewave dimmers must be set to 700ms for proper operation.
To
Modify Load
Profiles
To
Dimmer Config
Menu
Page 39
C21/EC21 Series Dimmer Rack
View Profiles Allow you to view the dimming curve for the dimmers, six dimmers at a time.
To
Modify Load
Profiles
To
Dimmer Config
Menu
Select Profiles Allows you to select the dimming curve for a range of dimmers:
SqLaw = Square Law
S-Crv = S-Curve
LinPw = Linear
N-Dim = Non-Dim
FlEle = Fluorescent Electronic
FlMag = Fluorescent Magnetic
MarkX = Advanced Mark X Ballasts
User1 = User Defined Dimming Curve #1
User2 = User Defined Dimming Curve #2
User3 = User Defined Dimming Curve #3
User4 = User Defined Dimming Curve #4
User5 = User Defined Dimming Curve #5
To
Modify Load
Profiles
To
Dimmer Config
Menu
View Cut Levels View Cut Levels
To
Modify Load
Profiles
To
Dimmer Config
Menu
Operations Manual
Page 40
Set Cut Levels Set Cut Levels
To
Modify Load
Profiles
To
Dimmer Config
Menu
View Minimum Levels Allows you to view the minimum dimmer output level, 6 dimmers at a time.
To
Modify Load
Profiles
To
Dimmer Config
Menu
Set Minimum Levels Allows you to set the minimum dimmer output level for a range of dimmers.
You can set a minimum level for any or all the dimmers. This can be used for
security or safety lighting in locations where a minimum light level is required under
all circumstances. This function can also be used as a preheat for large lamps.
Minimum levels are displayed in control percentages.
Note: This function sets the minimum control level applied to the dimmer,
not the minimum output voltage.
To
Modify Load
Profiles
To
Dimmer Config
Menu
Page 41
C21/EC21 Series Dimmer Rack
View Cable Impedance View Cable Impedance
To
Dimmer Config
Menu
C21 PROCESSO
R
C21 PROCESSO
R
C21 PROCESSO
R
Di m
m
er Conf i g M
enu
Di mm
er Dynami c Menu
To Di m
. Dynam
ic M
enu
Vi ew Cabl e I m
pedance
Cabl e I m
pedance - m:
001- 006
>
0
0
0
>
0
0
0
Rack_Name
Rack_Name
>
Rack_Nam
e
Set Cable Impedance Set Cable Impedance
To
Dimmer Config
Menu
C21 PROCESSO
R
C21 PROCESSO
R
C21 PROCESSO
R
Di m
m
er Conf i g M
enu
Di m
m
er Dynam
ic M
enu
Cabl e I m
pedance - m:
To Di m
. Dynam
ic M
enu
Set Cabl e I m
pedance
Rack_Nam
e
Rack_Nam
e
Rack_Nam
e
>001- 096=** *
View Report Enables View Report Enables
To
Dimmer Config
Menu
C21 PROCESSO
R
C21 PROCESSO
R
Di mm
er Conf i g M
enu
Di mm
er Dynami c M
enu
To Di m
. Dynam
ic M
enu
Vi ew Repor t Enabl es
Rack_Nam
e
Rack_Name
C21 PROCESSO
R
Rack_Name
Repor t Enabl e:
001 - 096
> On
O
n
> On
O
n
On
On
Set Report Enables Set Report Enables
To
Dimmer Config
Menu
C21 PROCESSO
R
C21 PROCESSO
R
C21 PROCESSO
R
Di m
m
er Conf i g M
enu
Di mm
er Dynam
i c Menu
Repor t Enabl e:
To Di m
. Dynam
ic M
enu
Set Repor t Enabl es
Rack_Nam
e
Operations Manual
Rack_Nam
e
Rack_Name
>001- 096=O
n
Page 42
View Trip Modes View Trip Modes
To
Modify Load
Profiles
To
Dimmer Config
Menu
Set Trip Modes Set Trip Modes
To
Modify Load
Profiles
To
Dimmer Config
Menu
C21 PROCESSO
R
C21 PROCESSO
R
C21 PROCESSO
R
Di mm
er Conf i g M
enu
Di mm
er Dynami c Menu
Tr i p M
ode:
To Di m
. Dynam
ic M
enu
Set Tr i p Modes
Rack_Name
Page 43
Rack_Name
Rack_Name
>001- 096=Of f
C21/EC21 Series Dimmer Rack
Input Config Menu
Input Config Menu allows you to view and set the Mux A and Mux B ports.
To Main Menu
From Main Menu
To Input Config
Menu Items
Set DMX A Options Allows you to set the DMX A port:
Off = Turns the DMX A port off
In = Allows you to define the net-slot range for the DMX A port.
(Default: In 001-512 02001)
SMX (Set for Outlook/SWC architectural control stations)
SVN (Set for Vision.Net architectural control stations)
To
Input Config
Menu
Set DMX A Label Allows you to create a label for the DMX A port.
To
Input Config
Menu
Set DMXB Options Allows you to set the DMX B port:
Off = Turns the DMX B port off
In = Allows you to define the net-slot range for the DMX B port.
(Default: In 001-512 03001)
SMX (Set for Outlook/SWC architectural control stations)
SVN (Set for Vision.Net architectural control stations)
Operations Manual
Page 44
To
Input Config
Menu
Set DMX B Label Allows you to create a label for the DMX B port.
To
Input Config
Menu
Set Panic Options Set Panic Options:
Options: Use Default Setting, On Request, Automatic, Disabled
To
Input Config
Menu
C21 PROCESSO
R
C21 PROCESSO
R
I nput Conf i g Menu
Pani c Opt i ons:
Rack_Name
Set Pani c Opt i ons
Rack_Name
>Use Def aul t Set t i ng
Enable AV Port Enables the Serial input port on the CIC board.
Options: Enabled, Disabled
To
Input Config
Menu
Messages are sent from an A/V controller at a maximum rate of 2 Hz
(2 messages per second).
UART Configuration:
9600 Baud, 8 data bits, No Parity, 1 stop bit
Message Overview:
Messages are composed of a short string of printing ASCII characters that request
certain actions from the rack processor. Messages are acknowledged by the
processor with confirming reply messages or with status update messages.
Page 45
C21/EC21 Series Dimmer Rack
Messages are transmitted as byte streams terminated by designated printing ASCII
characters. There is no requirement for line termination. Received characters that
do not have a defined function in the protocol are ignored.
Message Composition:
Messages are composed of a single command character, followed by an optional
numeric field that may be up to 3 characters long, followed by a single terminating
character. Thus, complete messages range from 2 to 5 characters long.
Command
1 byte
Parameter
0 to 3 bytes
Terminator
1 byte
For all messages received from the AV controller, the terminating character is the
letter ’Z’ in either upper or lower case (0x5A or 0x7A).
For all messages transmitted from the C21 Rack Processor, the terminating
character is the letter ‘Y’ (0x59).
The following messages are defined:
Play SWC Preset:
Command Code: ‘S’ or ‘s’ (0x53 or 0x73)
Parameter:
Up to three digits indicating an SWC preset number in the range
0..128. ‘0’ represents the “Off” preset.
Action:
The rack processor plays back the indicated SWC preset, and responds to the AV
controller with the identical message terminated with the ‘Y’ character instead of
‘Z’. If the preset number was out of range, the response message contains ”???”
instead of the preset requested.
Record SWC Preset:
Command Code:
‘R’ or ‘r’ (0x52 or 0x72)
Parameter:
Up to three digits indicating an SWC preset number in the range 1..128. ‘0’
represents the “Off” preset so is not allowed with this command.
Action:
The rack processor records the indicated SWC preset, and responds to the AV
controller with the identical message terminated with the ‘Y’ character instead of
‘Z’. If the preset number was out of range, the response message contains “???”
instead of the preset requested.
Play Outlook Preset:
Command Code:
‘O’ or ‘o’ (0x4F or 0x6F)
Parameter:
Up to three digits that represent two numeric fields. The first one or two digits
represent the room number. The last digit represents the preset number. The
room number may range from 0..15. The preset number may range from 0..9.
Preset 9 calls the “Full On” preset.
Action:
Operations Manual
Page 46
The rack processor plays back the indicated Outlook preset in the indicated room
and responds to the AV controller with the identical message terminated with ‘Y’
instead of ‘Z’. If the room number was out of range, the response message
contains “???” in place of the numeric parameter.
Record Outlook Preset:
Command Code:
‘P’ or ‘p’ (0x50 or 0x70)
Parameter:
Up to three digits that represent two numeric fields. The first one or two digits
represent the room number. The last digit represents the preset number. The
room number may range from 0..15. The preset number may range from 1..8.
Presets 0 and 9 are not allowed as these are not recordable.
Action:
The rack processor records the indicated Outlook preset in the indicated room and
responds to the AV controller with the identical message terminated with ‘Y’
instead of ‘Z’. If the room number or preset number was out of range, the
response message contains “???” in place of the numeric parameter.
Update System Status:
Command Code:
‘U’ or ‘u’ (0x55 or 0x75)
Parameter:
None
Action:
The rack processor responds by sending 17 response messages as defined above
indicating the states of the SWC system and of each room in the Outlook system.
Examples:
AV Controller Request
C21 Rack Response
“S001Z”
“S001Y”
SWC preset 1 is now active.
“s123z”
“s123Y”
SWC preset 123 is now active.
“s200z”
“s???Y”
No change in SWC due to out of range parameter.
“o123z”
“o123Y”
No change in Outlook due to out of range parameter.
“UZ”
“S123Y” “O000Y” “O010Y” “O020Y”
“O030Y” “O040Y” “O050Y” “O060Y”
“O070Y” “O080Y” “O090Y” “O100Y”
“O110Y” “O123Y” “O130Y” “O140Y”
“O150Y”
Page 47
C21/EC21 Series Dimmer Rack
Enable SMX Sharing Enables SMX Sharing.
Options: Enabled, Disabled
To
Input Config
Menu
C21 PROCESSO
R
C21 PROCESSO
R
I nput Conf i g Menu
C21 SM
X Shar i ng:
Rack_Name
Enabl e SM
X Shar i ng
Rack_Name
>Di sabl ed
Set SMX Sharing Group Sets SMX Sharing group.
To
SWC
Menu
C21 PROCESSO
R
C21 PROCESSO
R
I nput Conf i g Menu
SM
X Shar i ng Gr oup:
Rack_Name
Set SMX Shar i ng Gr oup
Rack_Name
>
0000
Enable SVN Sharing Enables SVN Sharing.
Options: Enabled, Disabled
To
Input Config
Menu
C21 PROCESSO
R
C21 PROCESSO
R
I nput Conf i g Menu
C21 SVN Shar i ng:
Rack_Name
Enabl e SVN Shar i ng
SWC Menu
Rack_Name
>Di sabl ed
SWC Menu
To Main Menu
From Main Menu
To SWC Menu
Items
Operations Manual
Page 48
Call SWC Preset Allows you to play-back one of the 128 SWC preset in the recorded time.
To
SWC
Menu
Record SWC Preset Allows you to record to one of the 128 presets
To
SWC
Menu
Set No Mux Preset Allows you to select one of the 128 presets as the No Mux Preset.
To
SWC
Menu
Set No Mux Hold Time Allows you to record a Hold Time for the No Mux Preset.
To
SWC
Menu
Set No Mux NetSlot Allows you to set the No Mux NetSlot number.
Page 49
C21/EC21 Series Dimmer Rack
To
SWC
Menu
C21 PROCESSO
R
C21 PROCESSO
R
SW
C Menu
No M
UX Net Sl ot :
Rack_Name
Set No M
UX Net Sl ot
Rack_Name
>
02001
Set Fade Time Allows you to record a Fade Time for and individual SWC preset.
The default is 0:00:03 seconds.
To
SWC
Menu
Set Fade Time Range Allows you to record a Fade Time for a range of SWC presets.
To
SWC
Menu
Edit SWC Event List Editor Allows you to view or edit 1of 24 events which will automatically recall an SWC
preset based on any day and time of the week.
To
SWC
Menu
Set Power-Up Preset Allows you to set the power-up preset.
To
SWC
Menu
C21 PROCESSO
R
C21 PROCESSO
R
SW
C Menu
Set Power - up Pr eset
Rack_Name
Set Power - Up Pr eset
Operations Manual
Rack_Name
>
000
Page 50
Outlook Menu
Outlook Menu
To Main Menu
From Main Menu
To Outlook Menu
Items
Call Outlook Preset Allows you to recall an Outlook preset in one of the 16 Outlook rooms.
To
Outlook
Menu
Call Outlook Pr. Range Allows you to recall an Outlook preset in a range of Outlook rooms. (Feature
currently not available).
Record Outlook Preset Allows you to select the Outlook room and preset number to record.
To
Outlook
Menu
Record Outlook Pr. Range Allows you to a range of Outlook rooms to record an Outlook preset into. (Feature
currently not available).
Set Channel Levels Set Channel Levels (Feature currently not available).
Set Ch. Levels Range Set Ch. Levels Range (Feature currently not available).
Page 51
C21/EC21 Series Dimmer Rack
Set Outlook Fade Time Set Outlook Fade Time
To
Outlook
Menu
Set Fade Time Range Set Fade Time Range (Feature currently not available).
Set Power-up Preset Set Power-up Preset (Feature currently not available).
Review Outlook Patch Review Outlook Patch
To
Outlook
Menu
Set Outlook Patch Set Outlook Patch
To
Outlook
Menu
Set Outlook Defaults Sets Outlook Defaults.
Options: Yes, No
To
Input Config
Menu
C21 PROCESSO
R
Rack_Name
Operations Manual
C21 PROCESSO
R
Rack_Name
Out l ook M
enu
Set Out l ook Def aul t s?
Set Out l ook Def aul t s
>No
Page 52
Local Control Menu
Local Control Menu
To Main Menu
From Main Menu
To Local Control
Menu Items
Set Dimmer level Allows you to set an individual dimmer to INPUT or to a local level between 0%
and FULL.
Note: Setting dimmer levels to something other than INPUT overrides the control
inputs, including presets, you can easily loose control of dimmers by forgetting to
set them back to INPUT. The levels set in this menu are remembered even when
you shut down the rack.
You can use the Set Dimmer levels menu to set dimmer levels in order to record
SWC and Outlook presets where there is no conventional lighting control system.
To
Local Control
Menu
Set Dimmer Lev. Range Allows you to set a range of dimmers to INPUT or to a local level between 0% and
FULL.
Note: Setting dimmer levels to something other than INPUT overrides the control
inputs, including presets, you can easily loose control of dimmers by forgetting to
set them back to INPUT. The levels set in this menu are remembered even when
you shut down the rack.
You can use the Set Dimmer levels menu to set dimmer levels in order to record
SWC and Outlook presets where there is no conventional lighting control system.
To
Local Control
Menu
Page 53
C21/EC21 Series Dimmer Rack
Call SWC Preset Allows you to recall one of the 128 SWC presets.
To
Local Control
Menu
Call Outlook Preset Allows you to recall an Outlook Preset in one of the 16 rooms.
To
Local Control
Menu
Status Reporting Menu
Status Reporting Menu
To Main Menu
From Main Menu
To Status Reporting
Menu Items
View Live Status View Live Status
To
Status Reporting
Menu
C21 PROCESSO
R
Rack_Name
St at us Repor t i ng M
enu
Vi ew Li ve St at us
Operations Manual
C21 PROCESSO
R
Rack_Name
>Di mm
er St at us: 083
Type=53 Nonr epor t i ng
L= 0%
Page 54
View Rack Status View Rack Status
To
Status Reporting
Menu
C21 PROCESSO
R
Rack_Name
St at us Repor t M
enu
Vi ew Rack St at us
C21 PROCESSO
R
Rack_Name
A=120v B=120v C=120v
60hz
60hz
60hz
Fan=100% Ai r = 70%
f
96 Di m
mer s
View Event Log View Event Log
To
Status Reporting
Menu
View Profile Stats View profile stats (Feature currently not available).
To
Input Config
Menu
C21 PROCESSO
R
C21 PROCESSO
R
St at us Repor t M
enu
Vi ew Pr of i l e St at s
Rack_Name
Vi ew Pr of i l e St at s
Rack_Name
>Unavai l abl e
View Comm Stats View comm stats (Feature currently not available).
To
Input Config
Menu
C21 PROCESSO
R
C21 PROCESSO
R
St at us Repor t M
enu
Vi ew Com
m St at s
Rack_Name
Vi ew Com
m St at s
Page 55
Rack_Name
>Unavai l abl e
C21/EC21 Series Dimmer Rack
View System Up-Time View System Up-Time.
To
Input Config
Menu
C21 PROCESSO
R
C21 PROCESSO
R
St at us Repor t M
enu
Syst em Up- Ti m
e:
Rack_Name
Vi ew Syst em Up- Ti m
e
Rack_Name
> 12 Dys 3: 27
Set Temperature Scale Sets temperature scale
Options: Celsius, Fahrenheit
To
Input Config
Menu
C21 PROCESSO
R
C21 PROCESSO
R
St at us Repor t M
enu
Temper at ur e Scal e:
Rack_Name
Set Temper at ur e Scal e
Rack_Name
>Fahr enhei t
Set Level Display Sets Level Display
Options: Percent, Decimal, Hex
To
Input Config
Menu
C21 PROCESSO
R
C21 PROCESSO
R
St at us Repor t M
enu
Level Di spl ay St yl e:
Rack_Name
Set Level Di spl ay
Rack_Name
>Per cent
Set Event Config Sets event configuration (Feature currently not available).
Options: Unavailable
Operations Manual
Page 56
To
Input Config
Menu
C21 PROCESSO
R
C21 PROCESSO
R
St at us Repor t M
enu
Set Event Conf i g
Rack_Name
Set Event Conf i g
Rack_Name
>Unavai l abl e
Enable Load Errors Enables load errors
Options: Enabled, Disabled
To
Input Config
Menu
C21 PROCESSO
R
Rack_Name
Factory Menu
C21 PROCESSO
R
Rack_Name
St at us Repor t M
enu
Load Er r or Det ect i on:
Enabl e Load Er r or s
>Di sabl ed
Factory Menu
To Main Menu
From Main Menu
To Factory Menu
Items
Set Rack Model Allows you to choose which rack model the processor is connect.
The options are:
C21, EC21
To
Factory
Menu
Page 57
C21/EC21 Series Dimmer Rack
Set Rack Backplane Allows you to select the backplane settings for the dimmer rack.
The options are: Normal, Half, Quarter,
To
Factory
Menu
C21 PROCESSO
R
C21 PROCESSO
R
Fact or y M
enu
Backpl ane Conf i g:
Rack_Name
Set Rack Backpl ane
Rack_Name
>Nor m
al
Set Rack Mains Allows you set the rack mains for 120V or 230V markets
To
Factory
Menu
Set Phase Config Allows you to set the rack phases for the 120V and 230V markets
The rack mains can be configured for 120V markets:
3-Phase: A-B-C-A-B-C or Single-Phase: A-A-A-C-C-C
The rack mains can be configured for 230V markets:
L1-L2-L3-L1-L2-L3
To
Factory
Menu
Set Rack Size Allows you to select the quantity of slots available in the dimmer rack.
The options are: 6, 12, 24, 36 or 48 slots
Operations Manual
Page 58
To
Factory
Menu
Set Rack Slot Order Allows you to choose if the slots are numbered horizontally or vertically through the
dimmer rack.
If this option is set to horizontal, then the slots are numbered from 1 to 6, left to
right across the top row. The slots in the second row are numbered from 7 to 12
and so on down all 8 rows.
The option is set to vertical, then the slots are numbers from 1 to 8 down the first
column. The slots in the second column are numbered from 9 to 16 and so on
across all 6 columns.
To
Factory
Menu
Set Rack Slot Usage Allows you to select the type of dimmer module that will the plugged into a dimmer
rack slot.
The options are: Unused, Single, Dual, Quad
To
Factory
Menu
Page 59
C21/EC21 Series Dimmer Rack
To Rack Calibration Sub- This option takes you to the rack calibration sub-menus
Menu
Set Phase Sense Trim Allows you to set the amplifier gain for the line voltage sensing circuit. Generally
this voltage is equal to the line input voltage for each phase. Adjusting the HEX
value between 000 and 255 sets the voltage level.
To
Factory
Menu
Set Phase Filters Allows you to set the width of the zero cross blanking period.
This function ensures that the processor module zero crossover time is
synchronized with the mains. You must not activate this while a control signal is
connected.
Default values: Width = 010 Lag = 000
Note: Do not calibrate the Phase Filters unless specifically advised to do
so by a representative of Strand Lighting.
To
Factory
Menu
C21 PROCESSO
R
C21 PROCESSO
R
C21 PROCESSO
R
Fact or y M
enu
Rack Cal i br at i on M
enu
Phase Fi l t er s:
To Rack Cal i br at i on
Set Phase Fi l t er s
Rack_Name
Rack_Name
Rack_Name
>W
i dt h=010
Lag=000
Revert to Mfg. Config. Allows you to set the rack back to factory defaults.
To
Factory
Menu
C21 PROCESSO
R
C21 PROCESSO
R
Rack Cal i br at i on M
enu
Rever t t o Mf g. Conf i g?
Rever t t o Mf g. Conf i g
> No
Rack_Name
Operations Manual
Rack_Name
C21 PROCESSO
R
Rack_Name
Ent er Passwor d:
>0000
Page 60
EEPROM Test Write EEPROM Test Write
To
Factory
Menu
C21 PROCESSO
R
C21 PROCESSO
R
Rack Cal i br at i on M
enu
Rack Cal i br at i on M
enu:
EEPROM Test W
ri t e
>Page: 000
Rack_Name
Rack_Name
Dat a: 000
EEPROM Test Read EEPROM Test Read
To
Factory
Menu
C21 PROCESSO
R
C21 PROCESSO
R
Rack Cal i br at i on M
enu
Rack Cal i br at i on M
enu:
EEPROM Test Read
>Page: 000
Rack_Name
Rack_Name
Dat a: 000
View Serial Number Allows you to view the serial number.
To
Factory
Menu
C21 PROCESSO
R
C21 PROCESSO
R
Fact or y M
enu
Ser i al Number :
Rack_Name
Vi ew Ser i al Num
ber
Rack_Name
> 00: E0: 01: 01: 11: 9A
Set Language Allows you to select the display language.
To
Factory
Menu
Set Project Name Allows you to edit the Project name text field. This name is different than the one
created in the Network Config Menu and is not viewed by the network.
Page 61
C21/EC21 Series Dimmer Rack
To
Factory
Menu
Set Dealer Name Allows you to edit the Dealer Name text field.
To
Factory
Menu
Set Dealer Contact Allows you to edit the Dealer Contact text field.
To
Factory
Menu
Set Dealer Extra Info. Allows you to edit the Dealer Extra Info text field.
To
Factory
Menu
Operations Manual
Page 62
Reboot Rack Allows you to force a soft re-boot of the C21/EC21 operating system.
To
Factory
Menu
Hide Factory Menu Allows you to hide this menu.
Note: Selecting this option requires a special key sequence to un-hide the Factory
Menu once it has been hidden.
To
Factory
Menu
Page 63
C21/EC21 Series Dimmer Rack
Section 4 - Basic Troubleshooting
General
This section provides basic troubleshooting procedures for C21/EC21 series
dimmer racks. It does not provide comprehensive maintenance data, but lets you
solve simple problems and helps Strand Lighting with initial data when these
procedures are not effective.
For best system operation, do a routine check and cleaning once per year unless
the operating environment is unusually harsh or dirty. Please consult Strand
Lighting Field Service if you are in doubt about the frequency of maintenance
required for your system. Service and maintenance operations other than routine
checks and cleaning are seldom required. In case of problems, and in order to
save time, follow the procedures outlined in this section before calling Strand
Lighting. Take note of the results of each step, as you will be asked this information
if you call a Strand Lighting service representative. In order to avoid
miscommunication, ensure that the person contacting Strand Lighting is the person
doing the tests. All servicing except dimmer and mechanical components should
be performed by sub-assembly replacement.
Operations Manual
Page 64
Section 5 – C21/EC21 Web Pages
General
This section provides basic information on the C21/EC21 Web Pages.
Web Page Main Screen Main Screen
Web Page Authorization Select [Home > Authorize] and enter the password: 2606 to become ‘Privileged’.
Page 65
C21/EC21 Series Dimmer Rack
Web Page Setup Select [Home > Setup] to gain access to the following options:
System
Dimmer
Patch
SWC
Outlook
Operations Manual
Page 66
Web Page System Select [Home > Setup > System > Parameters]
Parameters
Page 67
C21/EC21 Series Dimmer Rack
Web Page System Select [Home > Setup > System > Construction]
Construction .
Web Page Construction Select [Home > Setup > System > Construction Slots]
Slots .
Operations Manual
Page 68
Web Page Dimmer Select [Home > Setup > System > Modules]
Modules .
Page 69
C21/EC21 Series Dimmer Rack
Web Page Dimmer Select [Home > Setup > Dimmer > Circuits]
Circuits .
Operations Manual
Page 70
Web Page Dimmer Select [Home > Setup > Dimmer > Dynamics]
Dynamics .
Web Page Dimmer User Select [Home > Setup > Dimmer > User Profiles]
Profiles .
Page 71
C21/EC21 Series Dimmer Rack
Web Page Dimmer Select [Home > Setup > Dimmer > Tolerance]
Tolerance .
Web Page Dimmer Select [Home > Setup > Dimmer > Reporting]
Reporting .
Operations Manual
Page 72
Web Page Dimmer Patch Select [Home > Setup > Patch > Dimmer]
.
Web Page Firmware Select [Home > Setup > Firmware > Choose]
Update .
Page 73
C21/EC21 Series Dimmer Rack
Web Page Local Control Select [Home > Control > Local]
.
Operations Manual
Page 74
Page 75
C21/EC21 Series Dimmer Rack
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertisement