ActronAir SWB26C/E, SWB36C/E User manual

ActronAir SWB26C/E, SWB36C/E User manual
Before using your air conditioner, please read
this manual carefully and keep it for future reference.
AIR CONDITIONER
REMOTE CONTROLLER
User’s Manual
www.actronair.com.au
1800 119 229
Model Numbers
SWB26C/E
SWB36C/E
Read This Manual
Thank you very much for purchasing an ActronAir
air conditioner.
The design specifications are subject to change without prior notice for product
improvement. Consult with the sales agency or manufacturer for details.
Please read this owner’s manual
carefully before using your air conditioner.
R G 35A
202055090998 (9K)
20140527
last updated 20140527
Copyright 2014 ActronAir.
® Registered Trade Mark of ActronAir [ABN 34 002 767 240]
©
05/2014.
Handling the remote controller
CONTENTS
Location of the remote controller
Use the remote controller within a distance of 8
meters from the appliance, pointing it towards the
receiver. Reception is confirmed by a beep.
Handling the remote controller ...................................................... 2
Remote controller specifications................................................... 3
Function buttons .................. .........................................................
5
Indicators on LCD ..........................................................................
7
How to use the buttons .................................................................
8
Auto operation.................................................................................
8
Cooling/Heating/Fan operation......................................................
8
Dehumidifying operation ...............................................................
9
Adjusting air flow direction............................................................
9
Timer operation.............................................................................. 10
8m
CAUTIONS
The air conditioner will not operate if curtains, doors or other materials
block the signals from the remote controller to the indoor unit.
Prevent any liquid from falling into the remote controller. Do not expose
the remote controller to direct sunlight or heat.
If the infrared signal receiver on the indoor unit is exposed to direct
sunlight, the air conditioner may not function properly. Use curtains to
prevent the sunlight from falling on the receiver.
If other electrical appliances react to the remote controller, either move
these appliances or consult your local dealer.
LED/FOLLOW ME function ........................................................... 14
TURBO/SELF CLEAN function ....................................................... 14
Replacing batteries
NOTE: Replace the batteries when there is no receiving beep from the indoor
unit or if the transmission indicator on the remote controller fails to light.
The remote controller is powed by two dry batteries (R03/LR03X2) housed in the
rear part and protected by a cover.
(1) Remove the cover by pressing and sliding off.
(2) Remove the old batteries and insert the new batteries,placing the (+) and (-)
ends correctly.
(3) Reattach the cover by sliding it back into position.
NOTE: When the batteries are removed, the remote controller erases all programming. After inserting new batteries, the remote controller must be reprogrammed.
CAUTIONS
Do not mix old and new batteries or batteries of different types.
Do not leave the batteries in the remote controller if they are not
going to be used for 2 or 3 months.
Do not dispose batteries as unsorted municipal waste. Collection of such
waste separately for special treatment is necessary.
Remote Controller Specifications
Model
RG35A/BGEF
Rated Voltage
3.0V(Dry batteries 1.5V AAA x 2)
Signal Receiving
Range
8m (when using 3.0 voltage, it gets 11m)
Environment
-5ºC 60ºC
Function buttons
1
ON/OFF Button ( )
Operation starts when this button is pressed
and stops when this button is pressed again.
2
MODE Button
Each time the button is pressed, the operation
mode is selected in a sequence of following:
AUTO
3
DRY
HEAT
FAN
SWING Button
swing feature.
Performance Feature
1. Operating Mode: AUTO, COOL, DRY, HEAT (applicable to Cooling & Heating
models only) and FAN.
2. Timer Setting Function in 24 hours.
3. Indoor Setting Temperature Range : 17ºC~30ºC.
4. Full function of LCD (Liquid Crystal Display).
COOL
ON/OFF
1
SHORTCUT
M ODE
2
3
S WING
TEMP
FAN
SPE ED
D IRECT
TIMER
ON
TIMER
OFF
4
SLEEP
TU RB O
SEL FCLEAN
6
7
DIRECT Button
Used to change the louvre movement and set
the desired up/down air flow direction. The
O
louvre changes 6 in angle for each press.
5
SLEEP Button
Active/Disable SLEEP function. The Sleep function
enables the unit to automatically increase (cooling)
or decrease (heating) 1ºC per hour for the first two
hours, then holds steady for the next five hours, after
that the unit will stop operation. this fuction is only
available under Cooling, Heating and AUTO operations.
8
9
10
11
LED
FOLLOW ME
12
5
RESET
4
LOCK
13
14
NOTE: While the unit is running under SLEEP
mode, it would be cancelled if you press the MODE,
FAN SPEED or ON/OFF button.
6
TIMER ON Button
Press this button to initiate the auto-on time
sequence. Each press will increase the
auto-timed setting in 30 minutes increments.
When the setting time displays 10H, each
press will increase the auto-timed setting
60 minutes increments. To cancel the
auto-timed program, simply adjust the
auto-on time to 0:0.
11 TIMER OFF Button
7 TURBO/SELF CLEAN Button:
Press this button to initiate the auto-off time
sequence. Each press will increase the autotimed setting in 30 minutes increments. When
the setting time displays 10H, each press will
increase the auto-timed setting 60 minutes
increments. To cancel the auto-timed program,
simply adjust the auto-off time to 0:0
Activate / Disable TURBO function. If pressed
,
for more than 2 seconds, the SELF CLEAN
function will be activated, pushing more than
2 seconds again to disable.
,
8 UP Button (
)
Push this button to increase setting temperature
O
O
in a range of 17 C~30 C.
MO DE
SHORTCUT
2
3
DIRECT
4
SLEEP
TEMP
TIMER
ON
TURBO
SE LF CLE AN
FAN
SP EED
TIMER
OFF
RESET
8
9
10
11
LED
FOLLOW ME
12
5
6
7
Disable/Active indoor screen Display. When
pressed for more than 2 seconds, the
,
FOLLOW ME function will be activated. Press
again for more t n 2 seconds to disable.
LOCK
13
14
9
SHORTCUT Button
Used to restore the current settings or resume
previous settings.
When power is connected for the first time, select
the SHORTCUT button.The unit will operate on
O
AUTO mode, 24 C, and fan speed is Auto.
When this button is selected remote controller is on,
the system will automatically revert back to the
previous settings including operating mode,
setting temperature, fan speed level and sleep
feature (if activated). And transmit the signals to
the unit.
When this button is selected remote controller is off,
the system will only resume the previous settings
and will not transmit the signals to the unit. And
the sleep feature is disabled.
When you press button for more than 2 seconds,
the system will automatically restore the current
operation settings including operating mode, setting
temperature, fan speed level and sleep feature
(if activated ).
10 FAN SPEED Button
Used to select the fan speed in four steps:
AUTO LOW MED HIGH
,
ON/OFF
1
SWING
12 LED / FOLLOW ME Button
DOWN Button ( )
Push this button to decrease setting temperature
in a range of 17 OC~30 OC.
ON/OFF
1
SHORTCUT
M ODE
2
3
S WING
TEMP
FAN
SPE ED
D IRECT
TIMER
ON
TIMER
OFF
4
5
6
7
SLEEP
TU RB O
SEL FCLEAN
RESET
8
13
LOCK Button
When you press the recessed LOCK button,
all current settings are locked in and the
remote controller does not accept any
operation except that of the LOCK. Press
again to cancel the LOCK mode.
14
RESET Button:
When you press the recessed RESET button,
all current settings are cancelled and the
control will return to the initial settings.
9
10
11
LED
FOLLOW ME
12
LOCK
13
14
NOTE:
Buttons design might be slig htly
different from the actual one you
purchased depending on individual
models.
Indicators on LCD
How to use the buttons
Auto operation
Transmission Indicator
This transmission indicator lights when remote
controller transmits signals to the indoor unit.
Ensure the unit is plugged in and power is
ava ilable. T he OPERATION indi cator on the
display panel of the indoor unit start s flashing.
1. P ress the MO DE butt on to select A uto.
2. P ress the UP /DO WN but ton t o set the
desired t emperat ure. The temperature can
O
O
O
be se t within a range of 17 C~ 30 C in 1 C
increments.
3. P ress the ON/OFF button to start the a ir
conditioner.
Mode display
Displays the current operation mode. Including
auto (
), cool ( ), dry ( ), heat ( ) (Not
applicable to cooling only models), fan ( )
and back to auto (
).
auto cool dry
heat
fan
SET TEMP. TIMER ONOFF
sleep follow me lock
run
Tempe rature / Timer Display
O
O
Displays the temperature setting (17 C~30 C). When
you set the operating mode to FAN, no temperature
setting is displayed. And if in the TIMER mode, shows
the ON and OFF settings of the TIMER.
Fan speed display
Displays the selected fan speed, AUTO (no display)
and three fan speed levels " " (LOW) " " (MED)
" " (HIGH) can be indicated. The fan speed is AUTO
when the operating mode is either AUTO or DRY.
ON/OFF display
Displayed by pressing the ON/OFF button.
Press the ON/OFF button again to remove.
Lock Display
Displayed when LOCK mode is activated.
FOLLOW ME Display
Displayed when Follow me function is activated.
Sleep Display
Displayed under sleeping operation.
Press the SLEEP button again to remove.
Note:
All indicators shown in the figure are for the purpose
of clear presentation. But during the actual operation
only the relative functional signs are shown on the
display window.
ON/OFF
4
M ODE
SHORTCUT
2
1
SWING
TEMP
FAN
SPEED
DIREC T
TIMER
ON
TIMER
OFF
SLEEP
TURBO
SEL FC LEA N
RESET
LED
FO LLOW M E
LOCK
3
NOTE
1. In the Auto mode, the air conditioner can logically
choose the mode of Cooling, Fan, and Heating
by sensing the difference between the actual
ambient room temperature and the setting
temperature on the remote controller.
2. In the Auto mode, you can not switch the fan speed.
It has already been automatically controlled.
3. If the Auto mode is not comfortable for you , the
desired mode can be selected manually.
Cooling / Heating / Fan operation
En sure the unit is plugged in and power is
available.
1. Press the MODE butt on to select COOL,
HEAT(cooling & heating models only) or
FAN mode.
2. Press the UP/DOWN but tons to set the
desired t emperature. The temperature can
O
O
O
be set within a range of 17 C~ 30 C in 1 C
increments.
3. Press the FAN SPEE D button to select the
fan spee d in four steps- A uto, Low, Med,or
High.
4. Press the ON/OFF button to start the air
conditioner.
NOTE
In the FAN mode, the setting temperature is not
displayed in the remote controller and you are not
able to control the room temperature either. In this
case, only step 1, 3 and 4 may be performed.
Dehumidifying operation
Ensure the unit is plugged in and power is
available. The OPERATION indicator on the
display panel of the indoor un it starts flashing.
1. Press the MODE button to select DRY m ode .
2. Press the UP/DOWN buttons to set the
desired temperature. The temperature
O
O
ca n be set with in a range of 17 C~ 30 C
O
in 1 C inc rements.
3. Press the ON/OFF button to start th e air
co nditione r.
NOTE
ON/OFF
3
MODE
SHORTCUT
2
Timer operation
Press the TIMER ON button can set the auto-on
time of the unit. Press the TIMER OFF button
can set the auto-off time of the unit.
To set the Auto-on time.
ON/OFF
In the Dehumidifying mode, you can not switch the
fan speed. It has already been automatically controlled.
1
MODE
1
SWING
TEMP
FAN
SP EED
DI RECT
TIMER
ON
TIMER
OFF
SLEEP
TU RBO
SEL FC LEA N
LED
FOLLOW ME
RES ET
LOCK
Adjusting air flow direction
Use the SWING and DIRECT buttons to adjust
the desired airflow direction.
1. When press the DIRECT button, the horizontal
louvre changes 6º degree in angle for each press.
2. When press the SWING button, the louvre will
automatically swing up and down.
NOTE: When the horizontal louvre swing or move
to a position which would affect the cooling
or heating effect of the air conditioner, it
would automatically change the swing /
moving direction.
SWI NG
TEMP
FAN
SPEED
DIRECT
TIMER
ON
TIMER
OFF
2
SLEEP
TURBO
SELF CLEAN
RES ET
LED
FOLLOW ME
LOC K
1. Press the TIMER ON button. The remote
controller shows TIMER ON, the last Auto-on
setting time and the signal "H" will be shown on
the LCD display area. Now it is ready to reset
the Auto-on time to START the operation.
2. Push the TIMER ON button again to set desired
Auto-on time. Each time you press the button,
the time increases by half an hour between 0
and 10 hours and by one hour between 10 and
24 hours.
3. After setting the TIMER ON ,there will be a one
second delay before the remote controller
transmits the signal to the air conditioner. Then,
after approximately another 2 seconds, the
signal "H" will disappear and the set temperature
will re-appear and the TIMER ON will appear on the
LCD display window.
To set the Auto-off time.
1. Press the TIMER OFF button. The remote
controller shows TIMER OFF, the last Auto-off
setting time and the signal "H" will be shown on
the LCD display area. Now it is ready to reset
the Auto-off time to stop the operation.
2. Push the TIMER OFF button again to set
desired Auto-off time. Each time you press the
button, the time increases by half an hour
between 0 and 10 hours and by one hour
between 10 and 24 hours.
3. After setting the TIMER OFF ,there will be a
one second delay before the remote controller
transmits the signal to the air conditioner. Then,
after approximately another 2 seconds, the
signal "H" will disappear and the set temperature
will re-appear and the TIMER ON will appear on the
LCD display window.
! CAUTION
TIMER OFF
(Auto-off Operation)
The TIMER OFF feature is useful when you want the
unit to turn off automatically after you go to bed. The
air conditioner will stop automatically at the set time.
TIMER OFF
The effective operation time set by the remote controller for the timer function
is limited to the following settings: 0.5, 1.0, 1.5, 2.0, 2.5, 3.0, 3.5, 4.0, 4.5, 5.0,
5.5, 6.0, 6.5, 7.0, 7.5, 8.0, 8.5, 9.0, 9.5, 10, 11, 12, 13, 14, 15,16,17, 18, 19, 20,
21, 22, 23 and 24.
Stop
On
Set
10 hours later
Example of timer setting
TIMER ON
(Auto-on Operation)
The TIMER ON feature is useful when you want
the unit to turn on automatically before you return
home. The air conditioner will automatically start
operating at the set time.
TIM ER ON
COMBINED TIMER
(S etting both ON and OF F timers simultaneously)
Start
Off
Example:
6 hours later
Example:
To stop the air conditioner in 10 hours.
1. Press the TIMER OFF button, the last setting of
stopping operation time and the signal "H" will
show on the display area.
2. Press the TIMER OFF button to display "10H" on
the TIMER OFF display of the remote controller.
3. Wait for 3 seconds and the digital display area
will show the temperature again. The "TIMER
OFF" indicator remains on and this function is
activated.
To start the air conditioner in 6 hours.
1. Press the TIMER ON button, the last setting
of starting operation time and the signal "H"
will show on the display area.
2. Press the TIMER ON button to display "6:0H"
on the TIMER ON display of the remote
controller.
3. Wait for 3 seconds and the digital display
area will show the temperature again. The
"TIMER ON" indicator remains on and this
function is activated.
TIMER ON OFF
Start
Stop
On
Set
2 hours later
after setting
10 hours later
after setting
TIMER OFF
TIMER ON
(On
Stop
Start operation)
This feature is useful when you want to stop the air
conditioner after you go to bed, and start it again in
the morning when you wake up or when you return
home.
Example:
To stop the air conditioner 2 hours after setting and
start it again 10 hours after setting.
1. Press the TIMER OFF button.
2. Press the TIMER OFF button again to display
2.0H on the TIMER OFF display.
3. Press the TIMER ON button.
4. Press the TIMER ON button again to display 10H
on the TIMER ON display .
5. Wait for 3 seconds and the digital display area
will show the temperature again. The "TIMER
ON OFF" indicator remains on and this function is
activated.
Start
Stop
Off
Set
2 hours later
after setting
LED / FOLLOW ME function
TIMER ON
TIMER OFF
(Off
Start
Stop operation)
This feature is useful when you want to start
the air conditioner before you wake up and
stop it after you leave the house.
TIMER ON OFF
5 hours later
after setting
Example:
To start the air conditioner 2 hours after setting,
and stop it 5 hours after setting.
1. Press the TIMER ON button.
2. Press the TIMER ON button again to display
2.0Hon the TIMER ON display.
3. Press the TIMER OFF button.
4. Press the TIMER OFF button again to display
5.0Hon the TIMER OFF display .
5. Wait for 3 seconds and the digital display area
will show the temperature again. The "TIMER
ON OFF" indicator remains on and this function
is activated.
ON/OFF
MODE
SHORTCU T
SWING
TEMP
FAN
SPEED
DIRECT
TIMER
ON
TIME R
OFF
SL EEP
NOTE: The timer setting (TIMER ON or TIMER
OFF) that in sequence occurs directly after the
set time will be activated first.
When this button is pressed for less than
2 seconds this will initiate the LED function.
If this button is pressed for more than 2 seconds,
the FOLLOW ME function is initiated.
When the FOLLOW ME function is activated, the
rem ote d isplays the act ual temperature at its
location. The remote con trol will send this
signal to the air conditioner at 3 minut e
inte rvals until you press the FOLLOW ME b utton
aga in.
The Follow Me fu nction is not available un der
DRY and FA N mo de.
Switch t he operation mode or turn off the unit
will cancel th e Follow Me function automa tically.
TUR BO
SELF CLEAN
RESET
LED
FOLLOW ME
LOCK
TUR BO / SELF CLEAN function
1
2
When this button is pressed or less than 2 seconds
this will initiate TURBO function. If this button is
pressed for more than 2 seconds , the SELF CLEAN
function is initiated.
Turbo function enables the unit to reach the preset
temperature in the shortest time. When press this
button on cooling mode, the unit will blow strong
cooling air with super high fan speed. When press
this button on heating mode, will increase heating
operation.
Under SELF CLE AN mode, th e air co nditioner
will automat ically clean and d ry the Evaporator
and keep it as fresh for the next operation.
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertisement