Display - Siemens

Display - Siemens
SIMATIC 505
Isolated Interrupt
Discrete Input Modules
User Manual
Order Number: PPX:505–8123–2
Manual Assembly Number: 2586546–0085
Second Edition
!
DANGER
DANGER indicates an imminently hazardous situation that, if not avoided, will
result in death or serious injury.
DANGER is limited to the most extreme situations.
!
WARNING
WARNING indicates a potentially hazardous situation that, if not avoided, could
result in death or serious injury, and/or property damage.
!
CAUTION
CAUTION indicates a potentially hazardous situation that, if not avoided, could
result in minor or moderate injury, and/or damage to property.
CAUTION is also used for property-damage-only accidents.
Copyright 1995 by Siemens Industrial Automation, Inc.
All Rights Reserved — Printed in USA
Reproduction, transmission, or use of this document or contents is not permitted without express consent of
Siemens Industrial Automation, Inc. All rights, including rights created by patent grant or registration of a utility model or design, are
reserved.
Since Siemens Industrial Automation, Inc., does not possess full access to data concerning all of the uses and applications of
customer’s products, we do not assume responsibility either for customer product design or for any infringements of patents or rights
of others which may result from our assistance.
MANUAL PUBLICATION HISTORY
SIMATIC 505 Isolated Interrupt Discrete Input Modules User Manual
Order Manual Number: PPX:505-8123-2
Refer to this history in all correspondence and/or discussion about this manual.
Event
Date
Description
Original Issue
Second Edition
03/93
04/95
Original Issue (2801386–0001)
Second Edition (2801386–0002)
LIST OF EFFECTIVE PAGES
Pages
Cover/Copyright
History/Effective Pages
iii — vii
1-1 — 1-3
2-1 — 2-14
3-1 — 3-5
A-1 — A-4
Registration
Description
Second Edition
Second Edition
Second Edition
Second Edition
Second Edition
Second Edition
Second Edition
Second Edition
Pages
Description
Contents
Preface
Chapter 1 Product Overview
1.1
Description of Basic Features . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
1-2
Module Features . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Compatibility with SIMATIC CPUs . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Power Sources . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Operating Modes . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Optional Time Constant Filter . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Physical Features . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Manual Contents . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
1-2
1-2
1-2
1-2
1-2
1-3
1-3
Chapter 2 Installing the Module
2.1
2.2
2.3
2.4
2.5
Overview of Installation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
2-2
Flow of Tasks . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Handling the Module . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Visual Inspection . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
2-2
2-3
2-3
Configuring the Module Operating Mode . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
2-4
Selecting Interrupt Type . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Selecting 10-ms Time-Constant Filter . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Example Settings . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
2-4
2-5
2-6
Inserting the Module into the Base . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
2-7
Inserting the Module . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
2-7
Field Wiring . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
2-8
Wiring Guidelines . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Avoiding Noise . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Sequence of Inputs . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Wiring the Terminal Block . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Connecting the Terminal Block . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
2-8
2-8
2-9
2-11
2-12
Configuring I/O Memory in the CPU . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
2-14
Chapter 3 Operating the Module
3.1
3.2
Operational Description . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
3-2
Using the Module in Non-Interrupt Mode . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Using the Module in Interrupt Mode . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Writing an Interrupt RLL Program . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Basic Outline of Interrupt Processing . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
3-2
3-2
3-3
3-3
Module Status and Troubleshooting . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
3-4
LED Array . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Troubleshooting . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
3-4
3-5
Contents
iii
Appendix A Specifications
A.1
Specifications . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
A-2
A.2
Terminal Block Worksheet . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
A-4
iv
Contents
List of Figures
Figure 1-1 DC Interrupt Input Module . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Figure 2-1
Figure 2-2
Figure 2-3
Figure 2-4
Figure 2-5
Figure 2-6
Figure 2-7
Figure 2-8
Figure 2-9
Figure 2-10
Figure 2-11
1-3
Flowchart of Installation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Location of Interrupt Dipswitch Group . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
S1 Dipswitch Settings . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
S2 Dipswitch Settings . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Example Interrupt Type Settings . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Inserting the Module into the Base . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
I/O Terminals . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Field Input Wiring Examples . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Installing the Terminal Block . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Terminal Blocks . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Sample I/O Module Definition Chart . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
2-2
2-4
2-5
2-5
2-6
2-7
2-9
2-10
2-12
2-13
2-14
Figure 3-1 Interrupt Input Module Faceplate and LED Display . . . . . . . . . . . . . . . . . . . . . . . . . . . .
3-4
Figure A-1 Input Terminal Worksheet . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
A-4
Contents
v
List of Tables
Table 3-1 Logical Points Corresponding to Interrupt Inputs 9 – 16 . . . . . . . . . . . . . . . . . . . . . . . . .
Table 3-2 Troubleshooting Chart . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
3-2
3-5
Table A-1 Environmental Specifications . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Table A-2 Physical Specifications . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Table A-3 Electrical/Performance Specifications . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
A-2
A-2
A-3
vi
Contents
Preface
This manual provides the information needed to install, wire, and configure
the following SIMATIC 505 Isolated Interrupt Discrete Input Modules:
PPX:505–4317
24 VDC
PPX:505–4318
48 VDC
PPX:505–4319
125 VDC
Except for their input voltage differences, these modules function
identically.
Other Manuals
Agency Approvals
Refer to the manuals listed below for instructions on installing,
programming, and troubleshooting your controller and I/O. The x in the
order number refers to the latest edition.
•
SIMATIC 505 Programming Reference Manual (PPX:505–8104–x)
•
SIMATIC 525/535 Hardware/Installation Manual
(PPX:505–8103–x)
•
SIMATIC 545 System Manual (PPX:545–8101–x)
•
SIMATIC 555 System Manual (PPX:555–8101–x)
•
SIMATIC 560T/565T System Manual (PPX:560/565–8109–x)
•
SIMATIC 545/555 System Manual (PPX:545/555–8101–x)
•
The user manual for your release of TISOFT
The Interrupt Input Modules meet the standards of the following agencies:
•
Underwriters Laboratories: UL Listed (Industrial Control Equipment)
•
Canadian Standards Association: CSA Certified (Process Control
Equipment)
•
Factory Mutual Approved; Class I, Div. 2 Hazardous Locations
•
Verband Deutscher Elektrotechniker (VDE) 0160 Clearance/Creepage
for Electrical Equipment (Self-Compliance)
Series 505 products have been developed with consideration of the draft
standard of the International Electrotechnical Commission Committee
proposed standard (IEC-65A/WG6) for programmable controllers (released
as IEC 1131–2, Programmable Controllers Part 2: Equipment Requirements
and Tests, First Edition, 1992–09). Contact Siemens Industrial Automation,
Inc., for a listing of the standards to which Series 505 complies.
Telephoning for
Assistance
For technical assistance, contact your Siemens Industrial Automation, Inc.
distributor or sales office. If you need assistance in contacting your U.S.
distributor or sales office, call 1–800–964–4114.
SIMATIC 505 Interrupt Input Module User Manual
Preface
vii
Chapter 1
Product Overview
1.1
Description of Basic Features . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
1-2
Module Features . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Compatibility with SIMATIC CPUs . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Power Sources . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Operating Modes . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Optional Time Constant Filter . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Physical Features . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Manual Contents . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
1-2
1-2
1-2
1-2
1-2
1-3
1-3
SIMATIC 505 Interrupt Input Module User Manual
Product Overview
1-1
1.1
Description of Basic Features
Module Features
The SIMATIC 505 Isolated Interrupt Input Modules have 16 discrete input
circuits and operate on different voltages depending on the module. The
PPX:505–4317 operates on 24 VDC, the PPX:505–4318 on 48 VDC, and the
PPX:505–4319 on 125 VDC. Up to 8 of the 16 points can be configured as
interrupt points. Isolation is provided between each point. The modules
operate identically except for differences in input voltage.
The Interrupt Input Modules are compatible with all Series 505 bases.
Compatibility with
SIMATIC CPUs
The Interrupt Input Modules are compatible with all SIMATIC 505 CPUs
when used in the non-interrupt mode.
When interrupt mode is selected for any of the configurable inputs, the
module is compatible with the SIMATIC 545 and 555 CPUs with Firmware
Release 2.1 (or greater). Consult the release notes or other associated
documentation to determine if interrupt mode is supported by a particular
CPU.
Power Sources
The Interrupt Input Modules sense incoming DC signals from field devices
and operate on power supplied by the I/O base backplane. Refer to your
system manual for instructions on supplying power to the system I/O base.
Operating Modes
The Interrupt Input Module can be used in one of the following two modes.
•
16 isolated discrete inputs, all non-interrupt mode:
When this module is used in non-interrupt mode, it functions as a
standard 16-point discrete input module and can be installed in any
base (local or remote) of a Series 505 programmable controller system.
•
Configurable mix of interrupt inputs and non-interrupt inputs:
When this module is used in interrupt mode, it functions as a 32-point
I/O module (16 physical inputs and 16 internal points) and can only be
installed in the local base of the system. Local Base is defined as the
I/O base containing the CPU.
Interrupt input mode triggers an immediate response to a field device
condition without having to wait for the CPU to complete its program scan
cycle.
You can configure the module to detect transitions from on to off, off to on,
or either edge when you select interrupt type for a pair of input points.
Optional Time
Constant Filter
1-2
Product Overview
An eight-position dipswitch allows you to enable a 10-ms filter on any of the
16 physical input points in groups of two.
SIMATIC 505 Interrupt Input Module User Manual
Physical Features
The Interrupt Input Modules have two groups of dipswitches located at the
top of the board, as shown in Figure 1-1. The module includes a standard
input terminal connector which can be detached from the module without
having to remove the module from the base. An LED array on the faceplate
shows input status for each point and also interrupt enable mode.
Manual Contents
Chapter 2 describes how to configure the dipswitches, wire the terminal
block, and install the module.
Chapter 3 describes the basic operating features and the use of the LED
array for reading the status of the inputs.
Switch S1
Interrupt Type
Dipswitches
Switch S2
10-ms Filter
Dipswitches
Backplane
Connector
Input Status
LED Array
Input
Terminal
Block
Chart showing
dipswitch settings
Figure 1-1 DC Interrupt Input Module
SIMATIC 505 Interrupt Input Module User Manual
Product Overview
1-3
Chapter 2
Installing the Module
2.1
2.2
2.3
2.4
2.5
Overview of Installation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
2-2
Flow of Tasks . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Handling the Module . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Visual Inspection . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
2-2
2-3
2-3
Configuring the Module Operating Mode . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
2-4
Selecting Interrupt Type . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Selecting 10-ms Time-Constant Filter . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Example Settings . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
2-4
2-5
2-6
Inserting the Module into the Base . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
2-7
Inserting the Module . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
2-7
Field Wiring . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
2-8
Wiring Guidelines . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Avoiding Noise . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Sequence of Inputs . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Wiring the Terminal Block . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Connecting the Terminal Block . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
2-8
2-8
2-9
2-11
2-12
Configuring I/O Memory in the CPU . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
2-14
SIMATIC 505 Interrupt Input Module User Manual
Installing the Module
2-1
2.1
Overview of Installation
Flow of Tasks
Figure 2-1 shows the organization of the tasks described in this chapter.
Configure operating mode dipswitches
Insert module into base
Wire and connect input terminal block
Power up
Set I/O configuration with TISOFT programming device
Write I/O configuration to controller memory
Figure 2-1 Flowchart of Installation
2-2
Installing the Module
SIMATIC 505 Interrupt Input Module User Manual
Handling the
Module
Many integrated circuit (IC) devices are susceptible to damage by the
discharge of static electricity. Follow the suggestions listed below to reduce
the probability of damage to these devices when you are handling a CPU, a
base controller, or any of the I/O modules.
Both the module and the person handling the module should be at the same
ground potential. To accomplish this, fulfill the following conditions.
Visual Inspection
•
Transport the module in an anti-static container or antistatic material.
•
Ensure that the work area has a conductive pad with a lead connecting
it to a common ground.
•
Ground yourself by making contact with the conductive pad and/or by
wearing a grounded wrist strap.
If there is any visible damage to the module, contact your Siemens
Industrial Automation, Inc. distributor or sales office for replacement.
SIMATIC 505 Interrupt Input Module User Manual
Installing the Module
2-3
2.2
Configuring the Module Operating Mode
Selecting Interrupt
Type
Two groups of dipswitches are located on the top edge of the module facing
upward, as shown in Figure 2-2. The set of switches closest to the backplane
connector, labeled S1, is the group used to select interrupt type for points 9
through 16.
Switch S2
10-ms Filter
Dipswitches
Switch S1
Interrupt Type
Dipswitches
Backplane
Connector
Chart showing
dipswitch settings
Figure 2-2 Location of Interrupt Dipswitch Group
The interrupt type is selected for pairs of input points and cannot be
selected individually. Each pair of dipswitches in the S1 group selects the
interrupt mode for a pair of input points, as listed below.
Switches 1 and 2 control points 9 and 10
Switches 3 and 4 control points 11 and 12
Switches 5 and 6 control points 13 and 14
Switches 7 and 8 control points 15 and 16
You configure each pair of points to detect on-to-off, off-to-on, or either-edge
transitions according to the way you set each pair of dipswitches.
NOTE: This section discusses how to set the dipswitches to select interrupt
types for the configurable input points. To operate as interrupt inputs, these
points must also be enabled individually in the user program using the
internal logic outputs assigned to this task. Refer to Chapter 3 for more
information.
2-4
Installing the Module
SIMATIC 505 Interrupt Input Module User Manual
Figure 2-3 shows how to set the dipswitches in S1 to select the interrupt
type for each pair of input points.
Select Interrupt Type for each pair of
points according to the chart below.
Switch S1
Interrupt Type Switches
A
Each pair of switches selects interrupt type
for a pair of input points, as shown here.
OFF
A
B
A
B
A
B
A
Off
No Interrupt
Off
B
y
b
On-to-off edge
On
Off
ON
1
Input
Points
Interrupt Type
B
Off
2
9/10
3
4
5
11/12
6
13/14
7
Off-to-on edge
8
On
Either edge
15/16
On
On
Figure 2-3 S1 Dipswitch Settings
Selecting 10-ms
Time-Constant
Filter
The second set of dipswitches, located closest to the faceplate of the module
and labeled S2, is used to select input filter time constants of 10 ms per pair
of points, as shown in Figure 2-4. You can filter any of the 16 input points,
both non-interrupting and interrupting. The 10-ms filter may be useful in
applications where relay chatter or switch bounce is a potential problem.
NOTE: Filtering delays module response time to input transitions. For
interrupt applications with critical response time requirements, be careful
to take into account the time delay before you decide to use these filters.
Switch S2
10-ms Filter Switches
Each switch activates the filter for a
pair of input points, as shown here.
OFF
y
b
Off = no filter
On = 10-ms filter
ON
1
Input Points: 1/2
2
3
3/4
5/6
4
5
6
7
8
7/8 9/10 11/12 13/14 15/16
Figure 2-4 S2 Dipswitch Settings
SIMATIC 505 Interrupt Input Module User Manual
Installing the Module
2-5
Configuring the Module Operating Mode (continued)
Example Settings
Figure 2-5 shows an example of a configuration that enables interrupt mode
and the dipswitch setting used for the given configuration.
•
Points 9 and 10 are configured to be non-interrupting.
•
Points 11 and 12 are configured to generate an interrupt upon an
on-to-off transition.
•
Points 13 and 14 are configured to generate an interrupt upon an
off-to-on transition.
•
Points 15 and 16 are configured to generate an interrupt upon either
transition.
Switch S1
On-to-Off edge
Off-to-On edge
No Interrupt
OFF
Either edge
A
B
A
B
A
B
A
B
1
2
3
4
5
6
7
8
y
b
ON
Input Points:
9/10
11/12
13/14
15/16
Figure 2-5 Example Interrupt Type Settings
NOTE: To operate as interrupt inputs, these points must also be enabled
individually in the user program using the internal logic outputs assigned to
this task. Refer to Chapter 3 for more information.
2-6
Installing the Module
SIMATIC 505 Interrupt Input Module User Manual
2.3
Inserting the Module into the Base
!
WARNING
Failure to follow appropriate safety precautions could result in death or serious
injury and/or damage to equipment.
To minimize risk of potential shock hazard, turn off power to the I/O base and to
any modules installed in the base before inserting or removing a module or
installing a terminal block.
The power must be turned off to the I/O base and to any modules installed in
the base before inserting or removing a module or installing a terminal block.
Inserting the
Module
The Interrupt Input Modules are single-wide and may be installed in any
available slot for single-wide modules. Do not touch the printed circuit
board (PCB) while inserting the module. This could cause electrostatic
damage to its components. To insert the module, follow these steps.
1.
Position the module so that the front bezel is facing you.
2.
Hold the top and bottom of the bezel and slide the module carefully into
the slot, pushing it all the way into the base. If you have inserted the
module correctly, you will feel a slight increase in resistance as the
module mates with the backplane connector. (See Figure 2-6).
3.
Use a flat-head screwdriver to tighten the screws at the top and bottom
of the bezel. This grounds the module to the base. Do not overtighten.
0.3 N–m (2.61 in.-lbs.) minimum torque
0.6 N–m (5.22 in.-lbs.) maximum torque
Backplane
connectors
P
S
C
P
U
Earth
Ground
Figure 2-6 Inserting the Module into the Base
SIMATIC 505 Interrupt Input Module User Manual
Installing the Module
2-7
2.4
Field Wiring
Wiring Guidelines
These modules do not require user-supplied power. A module consumes a
maximum of 2.0 W of +5 V power from the base backplane.
The modules have been designed to work with up to 1000 feet (303 meters)
of wire to the switch. The size of the wire used must be adequate for switch
current. To prevent noise on the signal wiring, keep signal and power wiring
separate. For input or output signals and class 2 power supply wires, use
shielded, twisted-pair cable (12–26 AWG or 0.16–3.2 mm2, either stranded
or solid-type).
!
WARNING
Use supply wires suitable for at least 75°C. Signal wiring connected to this
module must be rated at least 300 V.
Wiring that does not meet the requirements could cause death and/or serious
injury or damage to equipment.
Ensure that your wire is suitable for at least 75°C, and that signal wiring connected to this module is rated at least 300 V.
Avoiding Noise
To minimize unwanted noise, follow these wiring installation guidelines.
•
Use the shortest possible wires.
•
Separate discrete and analog wires.
•
Avoid placing signal wires parallel to high-energy wires. If the two
must meet, cross them at right angles.
•
Avoid bending the wire into sharp angles.
•
Use wireways for wire routing.
•
When using shielded wires, ground them only at the source end for
better noise immunity.
•
Place wires so that they do not interfere with existing wiring.
•
Label the wires.
NOTE: Terminate shielding for the output cable at the same earth ground as
the user power supply. Terminate shielding for the input signal wire at the
same earth ground as the transmitter.
2-8
Installing the Module
SIMATIC 505 Interrupt Input Module User Manual
Sequence of Inputs
Figure 2-7 shows the sequence of inputs for the modules as well as the input
terminal label provided with the module. The right column represents the
right row of screws on the terminal block and the left column represents the
left row.
AC
Not used
AR
Input 1–
A1
Input 2–
Not used
BR
Input 5–
B1
Input 6–
B2
Input 7–
B3
Input 8–
B4
Input 10–
Input 11–
Input 12–
A2
B3
B4
C5
CC
Not used
CR
C5
Input 9+
C1
C6
C6
Input 10+
C2
C2
C7
C7
Input 11+
C3
C3
C8
C8
Input 12+
C4
C4
DC
D4
B8
Input 8+
C1
Input 16–
B7
Input 7+
CC
D3
B6
B2
CR
Input 15–
B5
Input 6+
B8
D2
BR
B1
B7
Input 14–
BC
Not used
Input 5+
B6
D1
A8
A4
B5
Input 13–
A3
Input 4+
BC
Not used
A7
Input 3+
A8
DR
A6
Input 2+
A7
Input 4–
Input 9–
A1
A6
A4
A5
Input 1+
A2
A3
Not used
AR
A5
Input 3–
AC
Not used
D5
DC
Not used
DR
D5
Input 13+
D1
D6
D6
Input 14+
D2
D7
D7
Input 15+
D3
D8
D8
Input 16+
D4
Terminal label
Terminal designators
(both connector models)
Figure 2-7 I/O Terminals
SIMATIC 505 Interrupt Input Module User Manual
Installing the Module
2-9
Field Wiring (continued)
The Interrupt Input Modules inputs are floating. Therefore, the inputs will
operate when wired in either a sinking or sourcing configuration, as shown
in Figure 2-8.
Field Side
+
–
Sourcing
Configuration
(Isolated)
Module Side
Input –
Input +
+
–
Input –
Input +
Sourcing
Configuration
Input –
Input +
Input –
Sinking
Configuration
(Isolated)
–
+
Input +
Input –
Sinking
Configuration
–
+
Input +
Input –
Input +
Figure 2-8 Field Input Wiring Examples
2-10
Installing the Module
SIMATIC 505 Interrupt Input Module User Manual
Wiring the Terminal
Block
You can use either of the terminal blocks shown in Figure 2-10. Both
terminal blocks are removable. To wire the terminal block, follow the
procedure below.
1.
Turn the terminal block, with the screw-heads facing you, until the
A-series of terminals is at the top and the D series is at the bottom.
2.
Using Figure 2-7 as a wiring guide, start with the D’s and loosen the
appropriate terminal block screws.
3.
Strip back the insulation on the wires about 1/4 to 3/8 inch or one
centimeter. Use a 12–26 AWG or a 0.16–3.2 mm2 metric gauge wire of
either stranded or solid type.
(If you are using the side-accessible connector number 2587705–8010, a
spade or a ring lug may be attached to the end of the wire.)
4.
Connect the end of the wire to the loosened terminal block screw and
tighten the screw firmly. Once the D’s are completed, connect the C’s,
and continue until the terminal block is completely wired.
NOTE: An easy-to-use, stick-on label is provided separately with space
available to write in the name of each input. Write in the corresponding
input names and apply the label to the flat side of the terminal block.
Appendix A contains a worksheet to help you document the input labeling.
SIMATIC 505 Interrupt Input Module User Manual
Installing the Module
2-11
Field Wiring (continued)
Connecting the
Terminal Block
To connect the terminal block to the module, follow these steps. (See
Figure 2-9.)
1.
Align the terminal block with the edge card connector on the bezel.
2.
Press firmly at both ends of the terminal block until it is seated.
3.
Tighten the screws at the top and bottom. Do not over-tighten.
Figure 2-9 Installing the Terminal Block
2-12
Installing the Module
SIMATIC 505 Interrupt Input Module User Manual
P/N 2587705–8011
Front-accessible
P/N 2587705–8010
Side-accessible
Connector –8010 accepts any of the
three wire terminations shown below.
Connector –8011 accepts only
the wire termination shown below.
Wire Gauge: 12–26
1 cm
(0.39 in.)
Wire Gauge: 12–26
1 cm
(0.39 in.)
Stud Size: #4 (2.5mm)
Amp Part#: 321462
Stud Size: #4 (2.5mm)
Amp Part#: 327891
Max. Width:
5.54 mm
(0.218 in.)
Max. Width:
4.62 mm
(0.182 in.)
Figure 2-10 Terminal Blocks
SIMATIC 505 Interrupt Input Module User Manual
Installing the Module
2-13
2.5
Configuring I/O Memory in the CPU
After the module has been inserted into the I/O base, you must register the
I/O addresses for each module in the CPU memory. (The module does not
automatically register addresses in the CPU when it is inserted.) This is
important because even though the module may appear to be operating
correctly, it will not communicate with the CPU unless the module is
configured in the I/O map. A programming device must be connected to the
CPU to configure the I/O map and verify CPU- to-module communications.
Apply power to the base and follow these steps to configure the I/O memory
map.
1.
Access the Configure I/O function menu.
2.
Select the appropriate channel and base number.
3.
Execute the Read Base function.
If the module is configured for non-interrupt mode, the module appears
as 16 X inputs, as shown in Figure 2-11, slot 1.
If the module is configured for interrupt mode, the module appears as
24 X inputs and 8 Y outputs, as shown in Figure 2-11, slot 2.
4.
You need to assign the starting I/O address and write the completed I/O
configuration to the controller memory. (In the example for slot 2, the
starting address is set for 0017.)
For more information on configuring the I/O, refer to your TISOFT manual.
I/O Address
Non-interrupt mode: the module logs in as 16 inputs (Xs).
Interrupt mode: the module logs in as 24 Xs and 8 outputs (Ys).
I/O MODULE DEFINITION FOR :
I/O
Slot
CHANNEL 1
Base Number
Displays number
of the current base.
BASE 00
Number of Bit and Word I/O
Special
Address
X
Y
WX
WY
1
..... 0001
..... 16
.. 00
.. 00
.. 00
.......
No
2
..... 0017
..... 24
.. 08
.. 00
.. 00
.......
No
3
..... 0000
..... 00
.. 00
.. 00
.. 00
.......
No
4
..... 0000
..... 00
.. 00
.. 00
.. 00
.......
No
Slot Number
Install the module into any
available I/O slot in the I/O base.
Function
SF Module
The Interrupt Input module is
not a Special Function Module.
Figure 2-11 Sample I/O Module Definition Chart
2-14
Installing the Module
SIMATIC 505 Interrupt Input Module User Manual
Chapter 3
Operating the Module
3.1
3.2
Operational Description . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
3-2
Using the Module in Non-Interrupt Mode . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Using the Module in Interrupt Mode . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Writing an Interrupt RLL Program . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Basic Outline of Interrupt Processing . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
3-2
3-2
3-3
3-3
Module Status and Troubleshooting . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
3-4
LED Array . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Troubleshooting . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
3-4
3-5
SIMATIC 505 Interrupt Input Module User Manual
Operating the Module
3-1
3.1
Operational Description
Using the Module
in Non-Interrupt
Mode
If you decide to use the Interrupt Input Modules in an application that does
not require interrupt inputs, and you have selected the No Interrupt
switch settings for each of the interrupt point pairs, then the module enters
Non-interrupt Mode when power is applied to the base.
In this mode, the module can be installed in any base (local or remote) of the
system and is recognized by the CPU as having 16 discrete input (X) points,
all of which are available for field connection.
Using the Module
in Interrupt Mode
If you selected an interrupt type for at least one of the pairs of configurable
input points, then the module enters Interrupt Mode when power is applied.
In this mode, the module can only be installed in the local base (the I/O base
containing the CPU module) and is recognized by the CPU as having 24
discrete input (X) points and 8 discrete output (Y) points.
In Interrupt Mode, the points are defined as follows.
•
Points 1 – 8: Non-interrupting field inputs
•
Points 9 – 16: Configurable (interrupting or non-interrupting) field
inputs based upon the settings of the interrupt switches on the module
•
Points 17 – 24: Logical (internal) status inputs that, when set by the
module, report to the CPU which point has generated an interrupt as a
result of a field input transition. Each of these points corresponds to
one of the interrupting field inputs, as shown in Table 3-1.
•
Points 25 – 32: Logical outputs that act as individual interrupt enables
for each of the interrupting field inputs. Turning on a given output
point enables interrupting operation on the corresponding input, as
shown in Table 3-1.
Table 3-1 Logical Points Corresponding to Interrupt Inputs 9 – 16
3-2
Physical Input
Points (X)
Logical Interrupt Status
Inputs (X)
Logical Interrupt Enable
Outputs (Y)
9
17
25
10
18
26
11
19
27
12
20
28
13
21
29
14
22
30
15
23
31
16
24
32
Operating the Module
SIMATIC 505 Interrupt Input Module User Manual
Writing an Interrupt
RLL Program
In order to take advantage of the Interrupt feature of this module, you must
write a Relay Ladder Logic (RLL) program that contains the appropriate
logic to execute the required response to interrupts generated by this
module. For a more detailed description of the requirements and operation
of the interrupt RLL program, refer to the SIMATIC TI545/TI555 System
Manual (PPX:545/555–8101–2) and the SIMATIC TI505 Programming
Reference Manual (PPX:505–8104–5).
Basic Outline of
Interrupt
Processing
The Interrupt Input Module and the CPU work together to process
interrupt signals in the following manner.
1.
When a field signal connected to an interrupt input transitions in a
manner that matches the interrupt type selected for that input, the
module sets the corresponding interrupt status input point and
generates an interrupt to the CPU.
2.
The CPU detects this interrupt, and, if proper qualifying conditions are
met, executes the interrupt RLL program, provided the CPU is in Run
Mode.
3.
The CPU automatically issues a rearm signal to the module to clear the
current interrupt event and to allow new events.
4.
If an interrupt transition occurs at a given input point while the CPU is
currently processing an interrupt event, the module holds the new
event until the CPU issues the rearm signal to complete processing of
the current event. The module then generates another interrupt to
signal the CPU that a new event has occurred.
NOTE: If an interrupt transition occurs at an input point while the module
is holding an event from the same input point, the new event will effectively
be lost, since the module will only generate a single interrupt to the CPU.
This behavior is significant only in pulse-counting applications, where
pulses could potentially be missed if the pulse frequency is too high. Refer to
your CPU’s Release Notes for specifications on execution times.
SIMATIC 505 Interrupt Input Module User Manual
Operating the Module
3-3
3.2
Module Status and Troubleshooting
LED Array
An LED array showing input and interrupt enable status is located on the
front of the module. (See Figure 3-1.)
24/48/125 VDC
Isolated/Interrupt
Input
Status
pts. 1–16
Interrupt
Enable
Status
LED Elements on Interrupt Input Module
Display
A1 – A4
B1 – B4
C1 – C4
D1 – D4
A5 – A8
B5 – B8
C5 – C8
D5 – D8
...
...
...
...
...
...
...
...
Function
status of points 1–4
status of points 5–8
status of points 9–12
status of points 13–16
not used
not used
interrupt enable status of points 9–12
interrupt enable status of points 13–16
PPX:505–4317/
PPX:505–4318/
PPX:505–4319
Figure 3-1 Interrupt Input Module Faceplate and LED Display
The input status LEDs indicate the state of the input from the logic (PLC)
side, not from the field side. When an input is on, a corresponding LED
turns on.
The interrupt enable LEDs indicate the status of the interrupt enable
logical outputs (points 25 – 32), which enable or disable the interrupt
operation for input points 9 – 16. Interrupt enable status of points 9 to 16 is
indicated by the status of LEDs C5 to C8 and D5 to D8.
These LEDs can be used to check normal module operation as well as to
troubleshoot when unexpected results are experienced.
3-4
Operating the Module
SIMATIC 505 Interrupt Input Module User Manual
Troubleshooting
The LED Input Status Indicators and the CPU indicate whether the module
is operating correctly. Table 3-2 shows symptoms, probable causes and
corrective actions to take if the module is not operating correctly.
Table 3-2 Troubleshooting Chart
Symptom
Probable Cause
Not receiving power
Nonfatal error as a
result of the module
Check power supply and
connections.
User program problem
Check user program or I/O
configuration.
Wrong terminal block
connections
Trace wiring connections.
Faulty LED
Return module for repair.
Wrong terminal block
connections
Trace wiring connections.
LED is not lit
Incorrect values
Corrective Action
Noise on signal wire
Use shielded wire near power
exceeding immunity level wire; check ground wire to base.
Incorrect or missing
configuration
Correctly configure I/O.
Module configured
incorrectly
Reconfigure the module.
If you cannot correct the problem, contact your Siemens Industrial
Automation, Inc. distributor or sales office.
SIMATIC 505 Interrupt Input Module User Manual
Operating the Module
3-5
Appendix A
Specifications
A.1
Specifications . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
A-2
A.2
Terminal Block Worksheet . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
A-4
SIMATIC 505 Interrupt Input Module User Manual
Specifications
A-1
A.1
Specifications
Table A-1 Environmental Specifications
Operating temperature
0 to 60°C (32 to 140°F)
Storage temperature
–40 to +70°C (–40 to 158°F)
Relative humidity
5% to 95% noncondensing
Pollution degree
2, IEC 664, 664A
Vibration
Sinusoidal
IEC 68-2-6, Test Fc
0.15 mm peak-to-peak, 10–57 Hz;
1.0 g, 57–150 Hz
Random
IEC 68-2-34, Test Fdc,
equivalent to NAVMAT P–9492
0.04 g2/Hz, 80–350 Hz, 3dB/Octave rolloff
80 – 20 Hz, 350 – 2000 Hz
Electrostatic discharge
IEC 801, Part 2, Level 4, (15 kV)
Shock
IEC 68-2-27; Test Ea
Noise immunity, conducted
IEC 801, Part 4, Level 3
Noise immunity on user power lines
MIL STD 461B CS01, CS02, and CS06 per part 4,
IEC 255-4, Appendix E; IEEE 472, 2.5 kV; EEC 4517
Noise immunity, radiated
IEC 801, Part 3, Level 3, MIL STD 461B RS01, &RS02
Isolation
1500 Vrms, input-to-controller
1500 Vrms, point-to-point
Corrosion protection
All parts of corrosion-resistant material or plated or
painted as corrosion protection
Table A-2 Physical Specifications
Module type
Series 505 single-wide module
Weight and dimensions of packed module
2 pounds, 15 ounces; 12.75″ × 13.5″ × 3.75″
Weight and dimensions of unpacked module
1 pound, 8 ounces; 10.5″ × 8″ × 0.8
Input signal wiring
Shielded, twisted-pair cable (12–26 AWG or 0.16–3.2
mm2, either stranded or solid-type)
Spade lug for use with connector 2587705–8010
Amp part number 321462
Ring lug for use with connector 2587705–8010
Amp part number 327891
Minimum torque for bezel screws
2.61 in-lb (0.3 N-m)
Maximum torque for bezel screws
5.22 in-lb (0.6 N-m)
A-2
Specifications
SIMATIC 505 Interrupt Input Module User Manual
Table A-3 Electrical/Performance Specifications
Module
PPX:505–4317
PPX:505–4318
PPX:505–4319
Rated Voltage DC
24
48
125
Input voltage range for ON
VDC UH minimum
VDC UH maximum
10.0
30.0
43.0
53.0
112.5
137.5
Input voltage range for OFF
VDC UL minimum
VDC UL maximum
–30.0
3.0
–30.0
10.0
–30.0
25.0
Input current limits during ON
mA IH minimum
mA IH maximum
2.0
10.0
1.0
6.0
1.0
4.0
Input current for OFF
mA maximum
0.5
0.5
0.5
Number of inputs
16 points in non-interrupt mode (16 Xs) 32 points
in interrupt mode (24 Xs, 8 Ys):
• 16 physical input points (16 Xs)
• 8 internal logic input points (8 Xs)
• 8 internal logic output points (8 Ys)
Delay time through module
0.5 ms maximum, filter off
10 ms maximum, filter on
Module power from base
2.0 W maximum (1.6 W typical) at +5 V
SIMATIC 505 Interrupt Input Module User Manual
Specifications
A-3
A.2
Terminal Block Worksheet
Not used
AR
Input 1–
A1
Input 2–
A2
Input 3–
A3
Input 4–
A4
Not used
BR
Input 5–
B1
Input 6–
B2
Input 7–
B3
Input 8–
B4
Not used
CR
Input 9–
C1
Input 10–
C2
Input 11–
C3
Input 12–
C4
Not used
DR
Input 13–
D1
Input 14–
D2
Input 15–
D3
Input 16–
D4
AC
Not used
A5
Input 1+
A6
Input 2+
A7
Input 3+
A8
Input 4+
BC
Not used
B5
Input 5+
B6
Input 6+
B7
Input 7+
B8
Input 8+
CC
Not used
C5
Input 9+
C6
Input 10+
C7
Input 11+
C8
Input 12+
DC
Not used
D5
Input 13+
D6
Input 14+
D7
Input 15+
D8
Input 16+
Terminal label
Figure A-1 Input Terminal Worksheet
A-4
Specifications
SIMATIC 505 Interrupt Input Module User Manual
Customer Response
We would like to know what you think about our user manuals so that we can serve you better.
How would you rate the quality of our manuals?
Excellent
Good
Fair
Poor
Accuracy
Organization
Clarity
Completeness
Graphics
Examples
Overall design
Size
Index
Would you be interested in giving us more detailed comments about our manuals?
Yes! Please send me a questionnaire.
No. Thanks anyway.
Your Name:
Title:
Telephone Number:
(
)
Company Name:
Company Address:
Manual Name:
SIMATIC 505 Isolated Interrupt Discrete Input Module
Manual Assembly Number: 2586546–0085
Order Number:
PPX:505–8123–2
Edition:
Date:
Second
04/95
FOLD
NO POSTAGE
NECESSARY
IF MAILED
IN THE
UNITED STATES
BUSINESS REPLY MAIL
FIRST CLASS
PERMIT NO.3
JOHNSON CITY, TN
POSTAGE WILL BE PAID BY ADDRESSEE
ATTN: Technical Communications M/S 519
SIEMENS INDUSTRIAL AUTOMATION INC.
3000 BILL GARLAND RD
P O BOX 1255
JOHNSON CITY TN 37605–1255
FOLD
SIMATIC is a registered trademark of Siemens AG.
Series 505 and TISOFT are trademarks of Siemens Industrial Automation, Inc.
Underwriters Laboratories is a registered trademark of Underwriters Laboratories.
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertisement