TFT Fingerprint V3.2 - Access Control Time Attendance Finger Scan

TFT Fingerprint V3.2 - Access Control Time Attendance Finger Scan
TFT Fingerprint V3.2
Important Notes
This fingerprint machine is designed to work with the newly issued
V3.X version Time & Attendance software only, which full compatible
with the original V2.X version that has been popularly applied to all
machines, the new one own the stronger function, the more convenient,
and more human nature for user than the V2.X version
TFT Fingerprint V3.2
Acknowledgements
Thank you purchasing our product, before working with this
machine, please read this manual carefully
Notice
Please do not place the product in the place with strong light,
because the strong light may significantly affect the fingerprint scanning,
and thus cause the fingerprint verification fail. This product is designed
for indoor installation, if it has to be installed it outdoor, please place the
equipment in proper environment, you must beware of not exposing it to
wet or harsh condition, the product work temperature rang is 0-40℃. Do
to use you machine in every hot environment, keep you machine away
from the heat source and radiator. For long time use it outdoor and the
internal heat of the machine, will cause problem to the operation
Notice: Fingerprint Enrollment and Identification shall be taken
after the installation the fingerprint identification machine
Installation
Enrollment
Enrollment
Installation
Identification
Identification
TFT Fingerprint V3.2
How to place the finger
Make sure the fingerprint image captured is of a core of presented finger,
a fingerprint is point to locate within innermost recurring ridge of any
give finger.
To obtain a higher success rate, enroll same finger 3times in a slightly
adjust angle, one to the center, one incline slightly to the left. The third
incline slightly to the right. You follow the following place procedure;
the success rate will increase dramatically
The correct way is:
Place a finger flatware on the sensor surface
Place it to the center of the sensor surface
The wrong way is
TFT Fingerprint V3.2
Notice: Please adopt the correct way to place the finger; Our
Company is not liable for any damages and troubles
whatsoever arising out of from improper pressing manners.
About this Manual
All functions in this document is subject the actual product , as a result
of the product is unceasing renewal, all attempts have been made to
make the information in this document complete and accurate. Our
company is not responsible for the actual product is consistent with this
material, is not liable for any direct or indirect damage or loss of
business resulting from in accuracies or omissions, the specification in
this document are subject to change without notice
Recommendation step
Step 1:Place the fingerprint machine properly and power up machine.
Step 2: Enroll user, register fingerprint and password, and assign
privilege to user.
Step 3: verify user, by the registered fingerprint and password is
available.
Step3: Configure the communication parameter; download the staff
information to software using the U flash disk or one of three ways
TFT Fingerprint V3.2
which is used to connect with the computer.
Step 5:Revise the staff’s information in the staff maintenances item of
software, connect the equipment with PC again and upload the staff
information to the equipment, at this time when the fingerprint machine
track staff’s Time & Attendance log , his/her name will be display on the
screen.
Step 6:Make a check for the fingerprint machine time, whether it is
correct, after completing setting up, then start to track employee’s
attendance.
Step7:At end of the month the downloaded attendance log to software
will be accounted.
The equipment is at the ready working status
After user verification completed by the fingerprint or the password the
attendance log will be saved in machine general
Readiness for work
The equipment is in readiness for work, shown as following picture:
TFT Fingerprint V3.2
Under the readiness for work, the advertising picture may be uploaded
by use self (please sees on 6.4 upload definition picture), also may
configure the clock setting (please see 4.5 interfaces setting).
What’s in attendance condition?
Mode 1
When the equipment is at the readiness for working, press the condition
key on the equipment to shift the attendance condition, and the states
information that correspond the condition key general display on the
screen, the condition of your choice shown as orange color . Press the
ESC key prompt information disappear. The definition of the default
condition key in the equipment, please see 4.4 keyboards definitions.
TFT Fingerprint V3.2
Mode 2
It is allowed to set up a number of state that is self -definition and
therefore when press button, do not indicate the state prompt
information, in the lower left-hand corner only shift the corresponding
state.
Track Time & Attendance
The attendance record will unable to be saved to the machine until
user verifies successfully with her/his the fingerprint or the
password.
u
Track Time & Attendance by Fingerprint
(1)1: 1 fingerprint validation (AC.NO +fingerprint)
Match the fingerprint which place the fingerprint sensor face and
type the one relate the number with keyboard entry, when user's
fingerprint quality is poor too recognize, this way 1:1 will be used.
Step 1:Verify personnel's AC.NO that keyboard entry in the initial
interface.
TFT Fingerprint V3.2
Step 2:Place finger on the sensor window in properly way
Step3 : The equipment prompt "thanks", the validation process
completed. When the equipment prompts "please place finger again
", go back to repeat this operation.
(2)1: N fingerprint validation
Match the fingerprint which is created by user press finger on the
TFT Fingerprint V3.2
sensor face and all fingerprints data in fingerprint machine
Step1: Press the fingerprint sensor with finger in proper method.
Step2:The equipment prompt "Thanks", the validation process
completed.
Step3:The equipment prompt "please place finger again ", go back
TFT Fingerprint V3.2
to repeat operation.
u
Track Time & Attendance by password
Step 1: Entry AC.NO belong to personnel who need to be verify in
the initial interface, press "OK" key
Step 2:If prompt the registered number is wrong, that means there is
no this personnel's number; if the prompt does not jump to the
password interface after press "OK" the key,
mean this staff has
not registered the password.
Step 3: the password interface appears, please input the password
TFT Fingerprint V3.2
.
Step 4:The equipment prompt "Thanks", the validation process is
completed.
The equipment prompts "the password is wrong", than the step repeat
operation.
TFT Fingerprint V3.2
About Access Control
After complete to assign The Access Control privilege, when the staff
go on authentication on the equipment, the equipment will determine
whether staff own privilege to open the door. If employees do not meet
conditions to unlock, the equipment will be given corresponding prompt,
the following by fingerprints to verify as an example:
1. Equipment motion that verification is successful, and output a unlock
signal.
TFT Fingerprint V3.2
2. The equipment prompt the Time Period is invalid.
This current time is without the Time Period employees is allowed to
open the door . Therefore, the staff could not open the door.
3. Prompt the invalid Group combine appear by the equipment.
TFT Fingerprint V3.2
This group where the staff locates is without unlocking combine.
Therefore, the staff could not open the door.
4. Motion to go on multi-user certification.
Until the group where user locates and the other group pass certification
together, it is not allowed to open the door.
TFT Fingerprint V3.2
5.The equipment motion to combination verification.
This is verification through the user or the group the users locate
combine verified, it is need to verify identity by multiple verification
Connect with PC
This equipment will only track the attendance time record, to get
statistics result is unable till the software process the attendance
record in the PC, therefore the need to connect machine with PC to
download attendance logs into Time & Attendance tracking software.
There are several ways to connect the machine and Time&
Attendance tracking software:
u
Ethernet
(1) Via the Hub: With Straight Thru Cable (apply to connect network
card and Hub) turns on, connect fingerprint machine to network.
(2)directly Connection: With T crossover cable(directly connect
two Ethernet terminal)connect fingerprint machine to PC
TFT Fingerprint V3.2
Machine Option: Enters the menu - communication Option, please
set the following several items:
IP address: default IP is 192.168.1.201, as your need change setting
Subnet mask: default Subnet mask is 255.255.255.0, you may change
it depending on actual need.
Gateway: the default gateway is 0.0.0.0, you may change it
depending on actual need
Network speed: The network run speed, there are automatic
adaptation, 10M, the 100M three options;
Connection password: in the “connection setting". May change
communication parameter, after setting, input the corresponding value
on connection interface in the PC software.
u
RS232 way
Machine setting: Enter the menu - communication option, please set
the following several items:
Baud rate: With the computer communication speed, the high speed
communication is quick, it is better to use the RS232 communication;
(115,200, 57,600).
RS232: Whether uses the RS232 communication, set this item as
“Yes”
Communication password: in the “connection setting". May change
communication parameter, after setting, must input the
corresponding value on connection interface in the PC
u
RS485 way
Machine Setting: Enter the menu – communication option, please
set up the following several items:
TFT Fingerprint V3.2
Serial number: Assign a network ID. The serial number scope is 1
– 254.
Baud rate: the computer communication speed, the low speed
communication is stable, we recommend that the RS485
communication Baud rate as (9,600, 38,400)
Whether uses the RS485 communication, set this item as “Yes”.
RS485: Communication password: in the “connection setting".
May set it or do not set it, after setting, must input the
corresponding value on connection interface in the PC.
u
USB way
Machine Setting: Entering the menu - communications settings, set
up following several Options:
Machine No: set it in the "Connection option". The number of
machines, Scope the 1-254;
USB: whether use USB communication, choose this item to yes.
Communications Password: set it in the "Connection
option". Maybe set it up or not, after set up ,input the
corresponding figure in the PC-Link software interface .
TFT Fingerprint V3.2
Contents
1 Main Windows ......................................................................................... 1
2 User Management .................................................................................... 1
2.1 Add new user ...................................................................................... 2
2.2 Users management.............................................................................. 6
2.3 Short message ★ ............................................................................. 17
2.4 work codes★.................................................................................... 23
2.5 Access Control setting ★ ................................................................ 26
2.6 Card management★ ......................................................................... 40
3 Communication setting.......................................................................... 48
3.1 Configure networks .......................................................................... 49
3.2 Configure serial port......................................................................... 50
3.3 Setting up connections...................................................................... 52
3.4 WiFi Setting★.................................................................................. 53
3.5 Wirless LAN★ ................................................................................. 57
3.6 Wiegand★........................................................................................ 58
4 System Setting ........................................................................................ 63
4.1 Systems parameters .......................................................................... 63
4.2 Data managements............................................................................ 65
4.3 Upgrade firmware............................................................................. 67
4.4 The definitions of keyboards★ ........................................................ 68
4.5 Window Setting ................................................................................ 72
4.6 Restore setting .................................................................................. 74
4.7 Bell setting★.................................................................................... 75
4.8 Misc Setting...................................................................................... 76
TFT Fingerprint V3.2
5 Time date ................................................................................................ 79
5.1 Time and Date settings ..................................................................... 79
5.2 Daylight Saving Time ....................................................................... 80
6 USB Flash disk management ................................................................ 82
6.1 Download attendance datum............................................................. 82
6.2 Download user’s data ....................................................................... 83
6.3 Download SMS★............................................................................. 84
6.4 Upload the user data ......................................................................... 84
6.5 Upload SMS★ ................................................................................. 84
6.6 Upload the customized picture ......................................................... 85
7. Automatically test ................................................................................. 87
7.1 Test TFT screen ................................................................................ 87
7.2 Test pronunciations ........................................................................... 88
7.3 Test keyboards .................................................................................. 88
7.4 Test fingerprint Sensor...................................................................... 88
7.5 Real-time clocks ............................................................................... 89
8. Inquiry record ....................................................................................... 90
8.1 Inquiry attendance ............................................................................ 90
9. Systems information ............................................................................. 93
9.1 Logs capacity.................................................................................... 93
9.2 Equipment information..................................................................... 94
Appendix 1 Getting familiar with keyboard........................................... 95
Appendix 2 T9 input method★ ............................................................. 100
Appendix 3 Multi–combination Authentication Mode ★ .................. 103
TFT Fingerprint V3.2
Appendix 4 Quickly inquiry the staff attendance logs......................... 109
Appendix 5 The rule about the advertising pictures.............................111
Appendix 6 anti-pass back function ★ ................................................ 112
Appendix 7 Photo ID ★ ........................................................................ 116
TFT Fingerprint V3.2
1 Main Windows
The fingerprint machine is in readiness state, Press
the main window, shown as following figure.
key to open
2 User Management
For a fingerprint machine, user's basic information includes fingerprint,
password and management privilege. When the company track staff
Time & Attendance log , as a result of reassign staff, the user
information in the fingerprint machine also needs to correspondingly
make the modification, therefore the fingerprint machine provide
function to add, delete, search, change user and so on the operation.
1
TFT Fingerprint V3.2
2.1 Add new user
Firstly register the personnel’s fingerprint or the password on the
machine. Whose time & attendance record will be tracked, Enter
the interface to add new user:
AC.NO: Staff's attendance number.
2
TFT Fingerprint V3.2
Name: use T 9 input method to keyin user’s name.
Note: only except iClock 100 fingerprint machine
Fingerprint: Registered staff's fingerprint, register ten fingerprints
available
The registered fingerprint staff is possible to use the fingerprint to
check attendance.
Registration password: The registration user's password, the
effective figure of password is 1 ~ 8.
The registered password staff is possible to use the password to
check attendance.
Privilege: Users are people whose identity must be authenticated
before enter a menu. The ordinary consumer can track attendance
by the fingerprint or the password only; the manager already may
equally carry on the daily checking attendance with the ordinary
consumer, but may enter the menu to operate each option.
Note: When there is no established the manager, any person all
may enter the menu operation; after establishing the manager, be
unable to enter the menu until the manager status is confirm, after
the success can enter the menu.
Example: the flow to add user as follows:
Input AC.NO
1) The equipment is assigned AC.NO by default.
2) Press the "
" key to delete the default assigned AC.NO, when
3
TFT Fingerprint V3.2
entry AC.NO with the keyboard, if occur error. May press " " to
delete it and input AC.NO again. Directly press "OK" key or scroll
the▲/▼ key, and locate cursor on the "Enroll fingerprint" button to
press the OK key again, go on the fingerprint registration.
Name
use T9 input method to key in user’s name.
Registration fingerprint
Follow the equipment prompt place the finger, you must
continuously press the same finger 3 times in the correct method
until the registration success prompt appear.
After registered the fingerprint successfully, if need to continue
register the fingerprint, please press the OK key , then place
another finger again, after registration completed, directly press
"
","ESC" key to return the main interface, the equipment can
show the number of fingerprint which presently has been already
registered.
scroll the▲/▼ key, and locate cursor on the "Enroll Password"
4
TFT Fingerprint V3.2
button to press the OK key again, go on the Password Registration
"the registration password" on the button.
Password registration
Following the equipment prompt, input the password , then press
OK key and input password once again , only can input 1 ~ 8 the
effective figure for the password . After the input to save completed
press "OK", if does not save it, press "ESC".
After saving it, the icon
will display on the screen, which
mean the password has already set in the device.
Privilege setting
Scroll the▲/▼ key, and locate cursor on the "Privilege" option
box, Scroll / key to choose privilege.
Save/exit user registration
To confirm the registration information is correct, after getting
5
TFT Fingerprint V3.2
confirmation, save it.
The way for saving:
1) Press "
" the key or scroll ▲/▼ key to locate cursor on the
"completes (
)"button, please press "OK" key again, the prompt "the
data has been changed, Are you sure to save it?” on the equipment, press
"OK" the key to save it, if you do not want saving, press "ESC" to exit.
If the prompt “Save successfully! Continues to input?" appear on
equipment, want continuing to press "OK", if you abandon this
operation, press "ESC" key.
2) Press the ESC key or scroll ▲/▼key to locate the cursor on the "
return (ESC)"button, please press "OK" key again, the prompt "the data
has been changed, Are you sure to save it" appear on equipment , press
"OK" key to save and return to the preceding of menus, does not serve
and return to the preceding of menus, press "ESC" key.
2.2 Users management
By means of the user management you can view all users' information in
the current equipment is available, which include username, the number
of fingerprint, whether the password is registered, and user’s attendance
logs. You are allowed to edit or delete some user.
6
TFT Fingerprint V3.2
Note: 1) Shown as above figure, the icon
express that this staff is a
manager, the icon
express that the password has been already
registered.
Press the "
" key in above figure, the following menu: pop-up
scroll the ▲/▼ key to enter your choice.
2.2.1 Search for users
When there are lot of registered user in the device, in order to provide
7
TFT Fingerprint V3.2
the manager with convenient rapidly to find a staff, the equipment come
with "AC.NO" to retrieve the staff.
Press the "
" key in the user management interface, the operation
menu appear, choose "search user". Or key in any numeric on the
keyboard:
Input staff's AC.NO you search for, press the "OK" key to search, after
searching successfully, the blue cursor will automatically locate on this
staff name, if this staff you search does not exist in the device, the
prompt "the non- registration data" will appear.
2.2.2 Inquiries Attendance
When the manager examine staff's registration information and
fingerprint so on, meanwhile may track the staff attendance record in the
same month.
Press the "
" key in the user management interface, the operation
8
TFT Fingerprint V3.2
menu appears, choose "Attendance inquires" item, may track the staff’s
that you choose the attendance record in the same month:
Scroll ▲/▼ key to browse the attendance log line by line.
Press PageUp/PageDown key to browse the attendance log page by page.
Press OK/
key to inquire the detailed situation.
After the examination completed, press "ESC" key to return to the user
9
TFT Fingerprint V3.2
management interface.
2.2.3 Editions users
Makes the revision for user's information which have been saved in the
machine, for example, if the registered fingerprint is invalid , renew the
registration fingerprint or register the password, just enter the " edition
user" available.
In the user management interface, scroll ▲/▼ key or utilize “searching
user” to designate staff who need edit , then press the "
" key to
choose the " edition user" in the operation menu; Or press quick key OK;
display the user’s information which has been registered:
The AC.NO is not allowed to revise again, other operations is similar
with to add the user. Register the fingerprint again, if there is not the
password or need to revise the password, then directly click on "Chg
Pwd", the privilege also is allowed to revise.
10
TFT Fingerprint V3.2
Save edition/Exit edition
1) Press "
" the key or scroll the▲/▼key to locate the cursor at the
completed " (
)"button. Press "OK" key again, save editing result and
return to the user management interface.
2) press the "ESC" key or scroll the ▲/▼key to locate the cursor at the
" (ESC)" button , press "OK" key again, prompt "the data have been
changed, are you sure to save it" display on the equipment press OK,
press “ ESC” key to abandon operation
2.2.4 Deletions users
The option "deletion user" is to delete staff's partial information or all
information from the equipment, which apply to the following situation:
1) The staff's fingerprint or the password is invalid or do not user any
more.
2) After the staff lay off, administrator deletes her/his record from the
equipment. In the user management interface, scroll the▲/▼ key or
search user to locate the blue color cursor at the staff that needs to edit,
press the "
" key. The operation menu appears, your choice is
"deletion user".
Deletion user
11
TFT Fingerprint V3.2
If there is not user’s fingerprint or the password in the device, then his
/her corresponding typeface is a blue color, be unable to operate it, scroll
the ▲/▼ key to locate the cursor at the option which need to operate.
Press the "OK" key pop-up the dialog box which asks you give
confirmation whether delete this item, after confirmation, the equipment
should create the corresponding prompt, press "ESC" key to return to
the user management page.
2.2.5 Add user
There is an option that is easily operator to add user in the here, the
function is some with 1.1 introduce.
2.2.6 User Access Control ★
In the user management interface, Scroll▲ / ▼ keys or search users
the blue cursor will be located in the staff who want to be edited, a
12
TFT Fingerprint V3.2
single-clock the operation of menu, select "User Access Control.".
User Access Control Setting is to set privilege to open the door for each
individual . These include: Group-owned setting, verification methods,
used Time Period, the verification methods, fingerprints management.
Group: registered users will be assigned to the group, it is easily
manageable;
Using Time Period
1) the group Time Period: the user whether or not use their default the
group Time Period.
2) Users Time Period: to set up the user unlock time. That is not to use
group time, the group does not affect the other people unlock time.
Verification methods
1) Group verification types: the user whether use the group verifying
types or not.
2) Personal validation types: individual users choose the type of
verification, or non-use type verification group, the group does not
affect other types of verification.
Duress fingerprint management
a newly registered users or specialized appoint a fingerprint which has
been registered in the fingerprint machine to the Duress fingerprints. In
any case, the fingerprint match successfully, then product the duress
alarm.
Note: equipment provides a wideJ range of types verify, specific See
Appendix 3, Multi- verification.
Instructions:
13
TFT Fingerprint V3.2
Scroll ▲ / ▼ key to move the cursor to the optional items. If the item is
the input box, input the value with the small number of key keyboard, If
it is a rolling box, Scroll / / key to switch the provided value, when
the cursor posit to "manage Duress fingerprint" button, Press
key to
enter the Duress fingerprints management. After completing setting,
directly press
or the menu key to save it and return to the
previous interface, press the "ESC" to Cancel and return to the previous
setting interface.
Duress fingerprints management
14
TFT Fingerprint V3.2
1) Definition / cancellation Duress fingerprints
on the above interface, Press the OK key to define / cancel the current
Duress fingerprints you selected. Press the menu button.
Choose canceled all, cancel all the fingerprints on the current page, Do
not serve as the duress fingerprints.
2) Duress fingerprint registration
In the above interface, press the menu button, to choose the "new"
option from the menu, then enter fingerprint registration interface, after
registering the successfully in the register interface you will find that
the fingerprints are designated as Duress fingerprints.
3) Save the duress fingerprints
15
TFT Fingerprint V3.2
If confirmed definition of duress fingerprint in the above interface , pres
the menu button, option "save.” appear in the menu
2.2.7 ID cards ★
Some equipments can also use ID cards to verify identity.
registration ID card
there is a ID card button in the new user interface of the machine with
ID cards function:
Scroll ▲ / ▼keys to locate the cursor to the "registration card" button
and press Ok key to enter the registration card keys:
Slightly wave the cards near induction area, after when the equipment
find the card, then remove the cards from the equipment, by the
equipment the card numbers will be readied to save and display on
screen. Press ESC key to exit, press Ok button to save and return to
confirm interface.
ID card verification
16
TFT Fingerprint V3.2
slightly wave the cards near induction area , after when the
equipment find the card , then remove the cards from the equipment
induction area, if the cards has been registered in this machine on the
equipment, the cardholder information will be displayed on the screen.
If the card is unregistered, no registration cards prompt appear.
Note: the card induction area is above fingerprint sensor about the 3 cm
-7cm .
2.3 Short message
★
The short message is similar to the bulletin, and the notice. It allowed
operator to schedule and edit the content of the short message that will
display on the screen. The short message is divided into the public short
message and individual short message, if the public short message has
been established, the icon
will display on the information bar of
the readiness window within the assigned time scope, the default key of
the equipment is "#" key (set the keyboard definition available) after
press this key to view the short message content. If the individual short
message has been established, then the system will distribute the short
message to the staff, after the staff track attendance successfully. He/she
will able to find the short message.
Instruction
17
TFT Fingerprint V3.2
scroll the ▲/▼ key to view the short message in line by line.
Scroll the PageUp/PageDown key to view the short message in page by
page.
Press "OK" the key to examine the detailed situation of the short
message, cannot change the short message.
Press
key, the short message menu will appear
2.3.1 Establish the short message
1) Add the short message
Scroll the ▲/▼ key to select the "add" choice of the short message in
the pop-up menu.
18
TFT Fingerprint V3.2
Start time: this time the short message becomes effective.
Effective period: within the effective period the short message will
display, after effective period is expired, the short message will not
display.
Message type: Individual: only for individual.
Public: All people are able to see.
Initialization: in advance set the short message, the
individual or the public short message will not be assigned.
Instruction
When the cursor locate in the text box, open the T9 input method, press
the "*" key to input the content of the short message, scroll the ▲/▼
key to switch the input box, scroll / to change setting or keyboard
and input the value with the small numeric keyboard.
(1) If the type of individual short message is your choice, the
distributing button is available; here the individual short message will be
distributed to the staff
19
TFT Fingerprint V3.2
Scroll the ▲/▼key to search personnel line by line .
Scroll PageUp/PageDown key to search personnel page by page.
Press the "OK" key to choose the personnel who is in the current
position, namely that express the short message has distribute to this
staff.
Press the
key to save your choice and exit.
Note: If before choosing personnel exit, this type of the short message
will become the initialization.
(2) If select the type of the public short message or initializes the short
message, then the distributing button will be disabled, after setting
completed, press
key to save and return to the short message list.
2) Edit the short message
Scroll the ▲/▼ key choice "edition" in the pop-up menu to edit the
short message.
The operation to edit the short message is same with one to add the short
message.
3) Delete the short message
scroll the ▲/▼ key choice " deletion " in the pop-up menu to delete the
20
TFT Fingerprint V3.2
short message.
Simultaneously eliminate all related information which is relating with
this record.
2.3.2 View staff the short message
1) Examine the public short message
when the equipment is at the readiness status, the main interface show
the picture and the current effective content of the public short message,
the interval to display time is same with the advertising picture
When the information bar of the machine main interface display the
prompt icon
, press the "#" key to view the current effective public
short message immediately.
21
TFT Fingerprint V3.2
2) Examine individual short message
when user through after confirmation, if this user has the short message
the short message content will be display.
The duration of the message display is 30 seconds, during the display
the user verification is available; close the current display to enter the
verification interface at this time.
22
TFT Fingerprint V3.2
2.4 work codes★
Track Time & Attendance record is basis to compute the salary, the staff
has possibly assign to the different working category, also has the
possibility to be dissimilar kind of work in one factory in the different
time, but for the different work category the reward is dissimilar,
therefore, the equipment provide user with parameter to indicate tracked
record that belongs to kind of working category in a factory, provide
convenience and very easy to process time & attendance data ,could fast
distinguish the different situation checking attendance.
Instruction
Scroll the ▲/▼key to view work code line by line .
Scroll the PageUp/PageDown key to view work code s page by page.
Press the "OK" key to edit view work code of your choice.
Press the
key, the menu to set work code will appear.
23
TFT Fingerprint V3.2
2.4.1 Set work code
1) Add the work code
scroll the ▲/▼ key choice "add" in the pop-up menu to add the short
work code.
Code: A number word code of this work code.
Name: express the mean of this work code.
2) Edit the work code
scroll the ▲/▼ key choice "edition" in the pop-up menu to edit the
work code.
24
TFT Fingerprint V3.2
The operation to edit the work code is same with one to add the work
code.
3) Delete the work code
scroll the ▲/▼ key choice " deletion " in the pop-up menu to delete the
work code.
Simultaneously eliminate all related information which is relating with
this record 2) edit the work code.
2.4.2 Using work code
When the equipment is in the readiness interface, press "*" the key
(allowed to set it in keyboard definition) enter the work code selection
interface.
The user may directly input work code, or scroll the ▲/▼ key to select
from the work list., press
main interface.
to choose it, then press OK key to return
25
TFT Fingerprint V3.2
2.5 Access Control setting ★
Access Control settings are designed for user’s Time Period and
control unlocks and related parameters of equipment settings.
if Registered users are unable to unlock untill he/she comply with the
following conditions:
1, the current unlock time should be within any effective Time Scope of
the User Time period or the user group Time Period;
2, where the user must be in unlock group combine (and user also can
work with other group unlock combine, but it is unable to unlock until
user work with together).
New register user belong to the first group of users by system default,
the default the group Time Period is "1", the default unlock combine is
the first group, and newly registered users is defaulted as the unlock
state (if the user has modify the related setting of the Access Control, the
system will change along with users).
Instructions:
26
TFT Fingerprint V3.2
Scroll ▲ / ▼ key to select,
item.
press OK button to performance selected
2.5.1 Set up Time Period
Time Period is a minimum Time Period unit of Access Control
option. The whole system can be defined with maximum 50 Time
Period. Each Time Period is the defined as seven hours a week, each
Time Period is the effective time in 24 hours a day . Each user can
own maximum3 Time Period, the three Time Period is "or" relationship,
as long as the Time Period the certification to meet one of these three
Time Period is effective. The time of each Time Period format: HH:
MM-HH: MM, in accordance with the 24-hour system that is accurate to
the minute.
The end of time is less than starting time (23:57 - 23:56) that represent
the day is prohibited, ending time is larger than starting time (00:00 23:59) that take effective in this range.
Users unlock the effective time of: opening day (00:00-23:59), or time,
the ending time than the beginning of time.
Note: the system's default Time Period is the No. 1 for opening day
(that is, newly registered users is permitted to unlock).
Instructions:
27
TFT Fingerprint V3.2
The first entry the number of Time Period, if the No. of Time Period has
been existed , then the Time Period setting will automatically refresh
and to be displayed. Scroll ▲ / ▼, / key to move cursor to the
input box, with the small number of keyboard input to the value you
want to set, after the completion, press the menu keys to save settings,
press the ESC key to exit.
2.5.2 Holidays setting
Introduce the concept of holidays to Access Control. Whenever the
holidays is taken, we may need a special Access Control hour, but it is
very tedious to change everyone's Access Control hours, it can be
used to set up a holiday Access control hour, and this Access control
hours is applicable to all staff.
Instructions:
28
TFT Fingerprint V3.2
1) additional holidays
Press a menu button, menu operation appear
Scroll ▲ / ▼ button to select new and entered the new interface
Scroll ▲ / ▼, key to move cursor to the input box, with the small
29
TFT Fingerprint V3.2
number of keyboard input to the value you want to set, after the
completion, press the menu keys to save settings, press the ESC key to
exit.
2) Editors holidays
The firstly select the line that want to be edited, directly press
OK
button or press the menu button, then the operation menu pup-up,
choose the Edition:
Scroll ▲ / ▼, key to move cursor to the input box, with the small
number of keyboard input to the value you want to set, after the
completion, press the menu keys to save settings, press the ESC key to
exit.
3) Delete the holidays
To delete the selected line, press the menu button, the operation menu
appear, choose item to be Deleted.
Note: If theJ Access Control holiday hours has been set, the user in the
holidays of a few days open the door that depend on the time set
here .
30
TFT Fingerprint V3.2
2.5.3 Group of Time Period setting
Group function is divided user into groups, personnel management, the
group using the default group staff Time Period, the group is allowed to
set the user Time Period. Each group has three Time Period. Newly
registered users belong to one group by default, but who can be
re-assigned to other various groups.
Instructions:
1) Add new group Time Period
Press a menu button, operation menu pop-up
Scroll ▲ / ▼ button to select new and entered the new interface, such as
31
TFT Fingerprint V3.2
adding a Group that include Time Period 2 and Time Period 3, as shown
below:
Note: 1, when the holidays Setting take effective, the Staff can not open
the door; until whose the group Time Period and holidays hours are
must be in intersection.
2, when the holidays set to be ineffective, then the team's entry time
from holiday.
Scroll ▲ / ▼ key to move the cursor to the items to be set up. If it is
the input box, input to provide value with the small number keyboard,
If it is a rolling box, scroll / key to switch and set its value, after
complete setting, directly press the menu keys to save setting and
return the previous interface, press the "ESC " button to Cancel and
return to the previous interface.
2) Editing group Time Period
firstly choose the line to be edited ,directly press
OK button or
press the menu button , choose the item to be edited in the event of
operation menu appear:
32
TFT Fingerprint V3.2
Scroll ▲ / ▼ key to move the cursor to the items to be set up. If it is
the input box, with the small number keyboard input to provide
value ,If it is a rolling box, scroll / key to switch and set its value,
after complete setting, directly press the menu keys to save setting and
return the previous interface, press the "ESC " button to Cancel and
return to the previous interface.
3) Delete the group Time Period
To delete the selected item, press the menu button, choose “Delete” in
the event of the operation menu appear.
2.5.4 Unlock combination setting
Each group will be combined into different unlock combination, so that
we can achieve multiple authentication functions and improving the
Access Control security. one in the largest unlock combination that can
have five groups formed.
Instructions:
33
TFT Fingerprint V3.2
1)new unlock combination
Press a menu button, the operation menu appear.
Scroll ▲ / ▼ key to select new and entered the new interface, such as
add a the combination that can unlock in event of which group 1, group
2 together verify successful, as shown below:
34
TFT Fingerprint V3.2
Scroll ▲ / ▼ key to move the cursor to the input box, input the value to
be set through the small number keyboard, after the completion, press
the menu keys to save settings, Press the ESC key to exit.
2) Editing unlock Combination
The firstly selected item to be edit, directly press the OK button or press
the menu button , choose “Edit” in the event of the operation menu
appear:
Scroll ▲ / ▼ key to move the cursor to the input box, input the value to
35
TFT Fingerprint V3.2
be set through the small number keyboard, after the completion, press
the menu keys to save settings, Press the ESC key to exit.
3) Delete unlocks combination
To delete the selected item, press the menu button, choose “Delete” in
the event of the operation menu appear.
2.5.5 Access Control Management Parameters
Configure Lock control and related equipment parameters. Duration of
locks driving: The equipment control performance to unlock after how
long time. (RMS 1 ~ 10 seconds)
door sensor delay: the door sensor delay is the duration after the door
was opened, How long time to check door sensor after a period of time
before detection to open the door, if door sensor state and door sensor
switch inconsistent normal began alarm, during this period of time is
door sensor delay. (RMS 1 ~ 5 seconds)
door sensor : There are three type: No, normally open, and NC
normal closed; None referring to the non-use of door sensor , and
normally open the doors opened that is normal, and normally close
that door closed is normal state.
Door sensor alarm delay: Do not detect door sensor state at normal
state , if over this hours to produce alarm signals, the hour is door sensor
alarm delay. (RMS 0 ~ 99 seconds)
Alarm Times by mistake: When the number of identification fail to
pass arrived at the number of the wrong values, they have a warning
signal. (RMS 0 ~ 9th)
36
TFT Fingerprint V3.2
Normal close Time Period : Access Control often set the door to
closed during the Period of Time, or any person in this period of time is
not able to unlock.
Normally open : set up a regular hours in Access Control system, the
lock in this period of time is in the opening state .
The validity of holidays: definition normally open or normally closed at
the time of the holidays, set a specific period of time take effect.
Note: 1, if the Time Period of normally open or normally closed has
been set, please switch door sensor to no, otherwise it will produce
alarm signal during Normal close Time Period or Normal open Time
Period .
2, If the normally open or normally closed Time Period is not
defined yet the time, the equipment will prompt that you define the
Time Period, and transferred to the Time Period interface , to adding.
Instructions:
37
TFT Fingerprint V3.2
Scroll ▲ / ▼ key to move the cursor to the items to be set up. If it is the
input box, input to provide value with the small number keyboard,If it
is a rolling box, scroll / key to switch and set its value, after
complete setting, directly press the menu keys to save setting and
return the previous interface, press the "ESC " button to Cancel and
return to the previous interface.
2.5.6 Duress alarm parameters
Machines also has Duress alarm parameter setting, use newly to enroll
specialties fingerprint or define an enrolled fingerprint as the duress
fingerprint , the system will trigger an alarm signal when this fingerprint
has been authenticate through fair and foul.
Seeking help by Keys: If this item set as "Yes", press hold down
PgDn keys ( for three seconds and above), produce the recourse signal;
press the PgDn keys followed (3 seconds) or input ID or place
fingerprint, after the success of identification at the same time a Duress
alarm will be triggered , if the keys for help is set to "no", then press
and hold down "▼" button, take no role.
1:1 verification methods alarm: If this item is set to "Yes", after users
performance 1:1 verification successfully, will produce alarm signals.
Otherwise there will be no warning signal.
1: N verification methods alarm: If this item is set to, "Yes", after
users performance 1: N verification successfully, will produce alarm
signals. otherwise there will be no warning signal.
Password alarm: If item is set to, "Yes", after user go on password
verification successfully , will trigger alarm signals, the contrary will
not alarm signal.
38
TFT Fingerprint V3.2
Alarm duration: after trigger the Duress alarm, Do not directly output
signal, but after a period of time that can be defined, then automatically
alarm signal (0-255 seconds).
Instructions:
Scroll ▲ / ▼ key to move the cursor to the items to be set up. If the
input box by the small number of key keyboard input to provide value If
it is a rolling box, according / key switch to set its value, directly
installed by the end of the menu keys can be set up and returned to the
preservation of the previous interface, Press the "ESC "Cancel to return
to the previous set and interface.
2.5.7 Anti-pass back Options★
Configure Anti-pass back function of this device, for more detail , please
refer to appendix 6 about anti-pass back function.
39
TFT Fingerprint V3.2
2.5.8 Relieve alarm
Equipment is in a state of alarm, press the menu button, the device will
be called "whether to relieve alarm?", alarm has been thrill until If you
relieve alarm state. After choice is to relieve alarm, the equipment will
return to normally state.
The type of alarm equipment: there are door sensor alarm, which
detection door was opened without authorization ,anti-dismantle
alarm . Duress alarm.
2.6 Card management★
The Mifare Card is contact less smart card ,the working frequency is
13.56 MHz and, can be integrated into our fingerprint biometric
verification reader, and can support a variety of verification methods to
meet the needs of different groups of people.
Instructions
40
TFT Fingerprint V3.2
Scroll ▲ / ▼ key to select, press
projects.
OK button to implement selected
2.6.1 Registration number card
Mifare cards maybe used as ID card, registration card number only, and
do not register fingerprints.
Instructions
1, registration
Step 1: Select button to register card number, press
41
OK to confirm.
TFT Fingerprint V3.2
Step 2: Press keyboard to input the registration number (if the number is
already existing in the user equipment, the equipment will be prompted
to copy the information of card), then press confirmed button
Step 3: The equipment prompt that please show cards.
Step 4: place the cards near the induction zones. the equipment will
prompt that register / copy successfully.
42
TFT Fingerprint V3.2
2, Verification:
wave the card near induction area, after the equipment find the card,
remove the cards from the equipment, after the equipment prompt that
verification is completed successfully verified.
Note : Please enter the user Access Control settings and switch to the RF
test, or they will not validated.
2.6.2 Registered fingerprint cards
Register fingerprints and write fingerprint into card.
Instructions
1, registration
Step 1: Select button to register fingerprint cards, Press
confirm.
43
OK to
TFT Fingerprint V3.2
Step 2: Press keyboard to input the registration number (if the number is
already existing in the user equipment, the equipment will be prompted
to copy the card information, go to step 4) and then press
OK keys
to confirm, equipment will prompt that place finger .
Step 3: correctly press finger three times.
Step 4: equipment will prompt ‘Please punch card’.
44
TFT Fingerprint V3.2
Step 5: place the cards near the induction area, waiting for the
equipment read fingerprint data into the card until the equipment motion
that the registration is successful.
2, Verification:
Slight ware card the near induction, after the equipment induct the card,
to be removed card from equipment , equipment motion to press
fingerprint, after successful and completion of verification. If the placed
fingerprint and storage of fingerprint cards is inconsistent, it would fail
to pass verification.
2.6.3 Clear Card Information
The current operation will delete all the information in the card.
Instructions
place the cards near area, waiting for all card information will be
deleted by the equipment ,if card data still is stored on the devices, the
45
TFT Fingerprint V3.2
equipment will also motion whether you want to remove the equipment
information, choose "Yes" , the user fingerprints and information in
the equipment, choose "no" , then keep up information in the device.
2.6.4 Copy card information
Card information will be copied to the device (after copying fingerprint
still exist in the card), after copying, directly track attendance on the
equipment by the fingerprinting, without the use of mifare cards.
Instructions
Scroll ▲ / ▼ key to select users, copy the information only, or copy the
user information and fingerprints and then press
OK to confirm
46
TFT Fingerprint V3.2
2.6.5 Card parameter setting
Set Mifare card passwords and the save information to the machine.
Fingerprint cards Password: after the password set up, the equipment
write the password into fingerprint card which has been registered in the
machine, then the fingerprint cards only is used in this machine.
Information must be saved to this machine: When register the
numbers card or the fingerprint card, whether will be kept to register the
information to the machine. Select item as the "no", the information
only store in the card; select as "yes", then the value store in this
equipment and card both.
Instructions
47
TFT Fingerprint V3.2
Scroll ▲ / ▼ key to move the cursor to the items to be set up. If it is the
input box, input to provide value with the small number keyboard,If it
is a rolling box, scroll / key to switch and set its value, after
complete setting, directly press the menu keys to save setting and
return the previous interface, press the "ESC " button to Cancel and
return to the previous interface.
Note: there induction area is above 3cm—5cm the fingerprint sensor.
3 Communication setting
If when transfer the data between the equipment and PC, it is necessary
to set the equipment communication parameter Press the transmission
cable, When the equipment and the machine are in the communication,
the "in the work... ... “Message will display on the equipment Please did
not operate the equipment by now.
Note: please inspect the setting here before the machines communicate
48
TFT Fingerprint V3.2
with the computer, the parameter must be consistent with one on the
communication option on the software.
3.1 Configure networks
To find sitting on the fingerprint machine if you are using Ethernet
communication, following sitting:
Machine IP address: Default IP is 192.168.1.239, you may change,
modify it; Do not set IP as same as the IP of PC that the fingerprint
machine connect with.
Subnet mask: Default mask 255.255.255.0, you may change, modify it.
Gateway address: the Default gateway address is 0.0.0.0, if the
equipment and PC is not in the identical network segment, set up the
gateway address firstly.
Network speed: The network run speed, there are three kinds of options,
automatic adoption, 10M, the 100M, set up network speed Press your
49
TFT Fingerprint V3.2
equipment that is plugged into a locate area network using Ethernet
cable
Instruction
Scroll the▲/▼、 / key to shift the cursor to input box, configure the
value with the numeric keyboard input, when it locate to the network
speed, scroll the / key to select value which is your favor. After the
set up, directly press
OK or the
key to save the settings and
return to unpaged, and return to an interface, press the ESC key to
cancel.
3.2 Configure serial port
To find sitting on the fingerprint machine if you are using serial port
(RS232/RS485) to communicate between the equipment and PC,
configure the following parameter:
Baud rate: the rate at which fingerprint machine communicate with the
50
TFT Fingerprint V3.2
PC , there are five kinds of options 9600, 19,200, 38,400, 57,600,
1.15200 bit/sec, the high speed communication is quick, we recommend
that high speed apply to the RS232communication ; The low speed
communication is stable, it is better the low speed apply to theRS485
communication;
RS232: Whether using RS232 communication or not, if the RS232 will
be used, then this choice is "Yes";
RS485: Whether using RS485 communication or not, if the RS485 will
be used, then this choice is "Yes”.
Instruction
Scroll the ▲/▼key to shift the cursor on the item you need set, scroll
the / key again to shift the value which you choose. After setting up,
directly or then press OK or
key to save this setting and return to
preceding interface, press the ESC key to cancel.
51
TFT Fingerprint V3.2
3.3 Setting up connections
It is necessary to set the serial number before the PC communicates with
the fingerprint machine over the RS232/RS485 cable.
Serial number: The serial number of the fingerprint machine, which
scope is from 1 to 254, if when using the RS232/RS485 communication,
be sure to input this serial number in the software communication
interface firstly.
In order to keep up the security of the time & attendance record data,
here you may set up the connection password, unless input this
connection password in the PC machine software and fingerprint
machine is unable to interconnect to read the data when the fingerprint
machine connect to PC successfully.
Connection password: The system default password is 0(namely the
password does not exist), it is allowed to set it as other values, after
setting up, be sure to input this password before the software
communicate with the equipment , otherwise you will fail to create
connection between the fingerprint machine and PC software. The
connection password length is 1 ~ 6.
Instruction
52
TFT Fingerprint V3.2
Scroll the▲/▼key shifts the cursor to input box, configure the value
with the numeric keyboard input. After the setup completed, directly
press OK or the
key to save the settings and return to preceding
interface, press the ESC key to give up option and return preceding
interface.
3.4 WiFi Setting★
Before the equipment apply to wireless Network, another physical
component of that 802.11 network consist Distribution system, Access
Point, Wireless Medium must exist.
You must know the ESSID (name of network) of local network you
want to connect to
wireless Network ID: local wireless Network that you want to connect
with (capital letter and small letter is different)
Network model: there are two option , Infrastructure Model, and Ad-
53
TFT Fingerprint V3.2
hoc Model; this Infrastructure Model will apply to Hub and Spoke
wireless network, the Ad-hoc Model is used in the peer to peer
wireless network..
the Authentication Type: The Infrastructure Model include five
Authentication Type that are OPEN 、SHARED、 WEPAUTO、
WPAPSK、 WPA2PS.
the Ad - hoc Model include OPEN 、 SHARED 、
WEPAUTO WPANONE four type of Authentication Type
Encrypt Type: When the item NONE of encrypt Type is selected, then
the password in WEP (Wired equivalent privacy) and WPA (WiFi
protested access) item is not permitted to modify it, it is not need to
input password too.
This PC IP address: If there is the DHCP function in the 802.11
network Distribution system , you may choose DHCP, press OK to exit.
Otherwise, full the IP Address,Subnet Mask blank with the correct
figure, press OK to exit to main interface.
Instruction
54
TFT Fingerprint V3.2
Scroll▲ / ▼ key to locate the cursor in the inputting box or the button ,
start the T9 inputting method, type the network identify ID, network
identification ID must be correctly enter , otherwise it will be unable
to move the cursor to the other input box, through scroll / button
to select the Items that need to input the other the input box is available,
or positioning in the confirmation button and then click the
corresponding button to enter the operation.
1)Set a password:
According to the choice of authentication methods and different forms
of encryption, password interface are also different. There are two
settings WEP and WPA .
WEP password
55
TFT Fingerprint V3.2
Type the valid password , there are the four groups password in the
WEP password, if the four groups have been set to the correct password,
only the currently selected password take effect.
WPA password
Enter the valid password , after set a password, Press OK/(M to save
your settings and return to wireless setting interface.
56
TFT Fingerprint V3.2
2)Assign IP:
Here assign the IP address to the wireless network equipment. Which
does not associates with the network settings of communications setting
After assigned IP to the device , Press OK to save your settings and
return to set up wireless interface.
After all set up by direct press OK to save the settings and return to the
previous interface, press the "ESC" to the cancellation and return to set
up an interface.
3.5 Wirless LAN★
Show equipment in the current environment in which the wireless signal
can be received and the strength of signals for users to select the
network to provide a better basis.
57
TFT Fingerprint V3.2
Menu button can be set according to the selected wireless network. ,
refresh the list is available by press OK key
3.6 Wiegand★
The definition of Wigand input and output format.
Pulse interval: which is default 900 microseconds, can be adjusted
between the 200 and 20000.
Output: wiegand output signals contained in the content choose to
include workers, or card number.
Instruction
58
TFT Fingerprint V3.2
3.6.1 Input Options
User self-definition format: Wiegand input format is defined by the
user-self.
Bit: the length of wiegand data bit.
Pulse Width: refers to the Wiegand pulse, width the default is 100
microseconds, can be adjusted within the scope of 20-800.
Pulse interval: the default 900 microseconds can be adjusted between
the 200-20000.
Pulse extent: weight input signal contain the content, which includes
choice of PIN, or card number.
Instruction
59
TFT Fingerprint V3.2
Type the name of self-definition format, scroll ▲ / ▼ key to move the
cursor to the item to be set up. If here is the input box, press the
number keys to input the value as you want to set, if here is rolling box,
scroll / key to switch the value , After completed .press OK to save
your settings and return preceding interface, press the "ESC" key to
cancellation and return to the preceding interface.
3.6.2 Output Options
Format: built-in system format , and it has been defined, users do not
need to specify the total length of all information and the location.
4 kind of definition format by the system default: wiegand26 with
sitecode, wiegand34 with sitecode, wiegand26 without sitecode,
wiegand34 without sitecode. The wiegand26 with sitecode refer to the
W26 output format with the equipment No. wiegand26 without sitecode
refer to the W26 format output without site code. If there is no set site
code, the output signal does not contain the information, if set up a site
60
TFT Fingerprint V3.2
code, the output is set a site code (similar to machines No., this is
different from the user's own code is designated, and the different
machines Can repeat, in the range between 0-255).
Failure ID: verify output after the failure of the failure of ID number,
when the choice is not the closure of the output. Range between
0-65534.
Site Code: similar to machines No., this is different from the user's own
code is designated, and the different machines can repeat, in the range
between 0-255.
Pulse Width: refers to the Wiegand pulse, width the default is 100
microseconds, can be adjusted within the scope of 20-800.
Pulse interval: the default 900 microseconds, can be adjusted between
the 200-20000
Pulse content: weight input signal contain the content, that include
choice of PIN, or card number
Instructions
61
TFT Fingerprint V3.2
Scroll ▲ / ▼ key to move the cursor to the item to be set up. If it is the
input box, type the number keys to input the value, if it is the rolling
box, scroll /
key to switch to set the value , for example, attempt
revise the failure to type ID figure to 10, scroll / key to set the
options as open, then enter10 figure in the box. After completed .press
OK to save your settings and return main interface, press the "ESC" key
to cancel and return to the main interface.
62
TFT Fingerprint V3.2
4 System Setting
To set up system parameter, make the equipment at the function, display
with the perfect exhibition, pursue user's satisfactions.
4.1 Systems parameters
1: 1 matching threshold: When use ID+ fingerprint to recognize.
Threshold a predefined number , often controlled by a biometric system
administrator , which establishes the degree of correlation necessary for
a comparison to be deemed a match .if the score resulting from template
comparison exceed the threshold , the templates are a “match” ( though
the template them selves are not identical
1: N matching threshold: the degree of correlation matches with the
registration template. Recommend matching threshold setting: e. (effect
63
TFT Fingerprint V3.2
value is 1 ~ 60 minutes)
Suggested Threshold Settings
FRR
FAR
One-to-many
One-to-one
High
Low
45
25
Middle
Middle
35
15
Low
High
25
10
Time format: Set up the time format in the fingerprint initial interface.
Scroll /
key to choose form, the fingerprint machine supports 10
kinds of dates forms, YY-MM-DD, YY/MM/DD, YY.MM.DD,
MM-DD-YY, MM/DD/YY, MM.DD.YY, DD-MM-YY, DD/MM/YY,
DD.MM.YY, YYYYMMDD, and other date form of your choice
Keyboard voice: Scroll the / key to determine the whether send a
sound when you press key , if set the option as "Yes" ,when press key
the machine will utter, if set the option as ("No") you press key the
machine doesn’t utter.
Voice (Adjvo): Through the / / key configure the voice prompt, the
equipment can produces the corresponding voice Prompt when the
operation.
Volume: Adjust volume. Scroll
/ key to adjust volume as your favor
Alarm attendance log( Alms Attlog), When the remainder log capacity
reached set numerical value, it will automatically sound warning that
logs will be full ( virtual value is 1-99).
Recheck Minute: set it within the scope (unit: minute). Someone
64
TFT Fingerprint V3.2
attendance has been recorded, then the second record will not display
(virtual value is 66)
Instruction
Scroll the▲/▼key to shifts the cursor on the item which you need set. If
the item is inputting box, configure the value with the numeric keyboard
input; If the item is rolls the frame, Scroll the / key to choose the
value you need, after the setting finished, please directly press OK or
key to save this item and return to preceding interface, press the
ESC key to give up operation and return to interface.
4.2 Data managements
Delete attendance record (Clear Attlog): Deletes all attendance record.
Delete the complete datum (Clear All): Delete all registrations personnel
information, the fingerprint and the attendance record.
Clear Admin Privilege: Change the Administer privilege into ordinary
users’ option:
65
TFT Fingerprint V3.2
Instruction
Scroll the▲/▼ key to shift the cursor on the button which you will
operate. press OK or
to start operation, when the prompt “ Are you
sure to continue the current this operation?” appear on the equipment,
press OK or
key again , be sure that the data will be deleted, if after
you delete the data, the data will be unable to restore. Press ESC key to
exit and return to up aged.
Clear picture: to eliminate the picture by the U flash disk on equipment.
(How to upload picture, please to see 5.4 to upload definition picture)
Instruction
66
TFT Fingerprint V3.2
Scroll the "▲/▼" key to preview the advertising picture which has
already saved in the equipment, if you want to delete this picture then
click on the OK key to delete it, after the prompt to delete successfully
appear on the equipment , after deleted completed automatically jumps
to the next picture. If you want to delete all advertising picture in the
equipment, click Clear All button. Press the ESC key to return to the
data management interface.
4.3 Upgrade firmware
If want to upgrade the firmware of machine, my use the USB flash disk
through this option.
Caution: the user does not random upgrade the firmware, you must be
allowed by the dealer before to upgrade the firmware, voluntarily
upgrade occur the trouble which possibly affect your normal use
Instruction
67
TFT Fingerprint V3.2
Plug the USB flash disk with Upgrade file into slot, click on this item,
the equipment will automatically recognize upgrading file and upgrade
firmware, the corresponding prompt will appear to show upgrade
successfully or fail.
4.4 The definitions of keyboards★
4.4.1 Condition key definition
Customize the attendance condition key on the equipment, after press
the corresponding condition key again, the attendance condition of this
attendance record is this condition key.
When press any condition key on initial interface left, the attendance
condition which correspond the condition key will appear under the
screen left, provide user with the convenient to examine.
Instruction
68
TFT Fingerprint V3.2
Scroll the ▲/▼ key to shift option box, Scroll / key to change the
setting. After you complete set up, please press "OK" to save this
configuration, press the ESC key to abandon operation and return to the
interface.
Note: If some condition keys have no use , then set this condition key as
invalid.
4.4.2 Short cut keys definitions
To define the short cut function of each key, it is allowed to define a key
as the short cut key for the attendance condition or view function of the
shortcut key. When the equipment is in the readiness interface, press the
key to display the Time & Attendance condition or fast quickly enter the
function interface.
Instruction
the shortcut key definition Scroll ▲/▼ key to browse key line by line.
the shortcut key definition. Scroll PageUp/PageDown key to browse
69
TFT Fingerprint V3.2
page by page
press "OK" to key edit the selected shortcut key .
4.4.2.1 set short cut keys
Select a shortcut key, press OK to enter the edition interface.
Function: set this key to the shortcut function. Include the condition key,
work code, the short message.
After the condition key is selected the following option appears:
Code: Assigns a code to the condition key, provide user with convenient
to view and statistics record .
Name: This key indicates the name of condition.
Automatic switch: When arrives at the appoint time, equipment
automatically switch the attendance condition.
1) Set to the function key
Instruction
Scroll / key, the "*" key may be defined to work code or the short
message, the function definition key.
70
TFT Fingerprint V3.2
2) Establishes as the condition key
Scroll ▲/▼the key to switch input box, press the numeric key to
input or Scroll / key to set the value. After the setting completed,
directly press
to save and returns to interface, the press "ESC" to
cancel setting and return to the interface.
4.4.2.2 Use shortcut keys
1) condition key
press "F3" as the equipment is in readiness window, the corresponding
condition icon will appear below left corner of the screen
71
TFT Fingerprint V3.2
2)the Function of the shortcut key
For example, set the“ * ”key to work code in the setting option .
Press“*”key to enter the work code choice interface.
4.5 Window Setting
When user go on verification with 1: 1 matching or password, the
following situation, to forgot the registered finger or improperly press
the finger, possibility to appear, provide user the convenient to reduce
the repetition times to press key, after if you fail to confirm the
equipment will permits you try again. You also may do yourself favor to
set the initial windows.
Clock mode: After the user verifying operation, the clock style of your
choice will display on the verification screen here, regardless of the
success or failure.
Advertising Picture: The user may place some the advertising pictures
display on the screen Press need.
72
TFT Fingerprint V3.2
1) The circulation interval of the picture (Picture Loop) refer how long
time separately transfer the advertising picture (virtual value is 3 ~ 999
seconds)
2) the time delay refer to how long the clock picture display after the
user verification finished, the time delay pass over, the initial window
will display the advertising picture again. (Virtual is 0~ 999 seconds, 0
express continuously display clock picture.)
Instruction
Scroll the▲/▼key shifts the cursor to input box, set up the value with
the numeric keyboard input,. After the set up, directly press OK or the
key to save the settings and return to preceding interface, press
the ESC key cancellation and return to on an interface
73
TFT Fingerprint V3.2
4.6 Restore setting
Restore the communications setting, system settings, to the factory
settings.
Reset all the default Parameters: the parameters of the machine will
be fully restored to factory settings.
Reset the keyboard Parameters: the keyboard corresponding
definition set to the factory settings.
Reset Alarm Parameters:the alarm settings call back to the factory
settings.
Reset Other Parameters: communications settings, system parameters,
such as the interface settings call back to the factory settings.
Reset Access Parameters: access control settings and user access
control settings back to the factory settings
74
TFT Fingerprint V3.2
Scroll ▲ / ▼ key to select, press OK button to restore the settings.
Note: when Restores the setting cannot erase the personnel information
and the attendance record in the equipment
4.7 Bell setting★
It is popular to ring in many companies when the people should be work,
but there are two the tradition way to ring with the man-power or the
special electron. In order to get economy and convenience management,
we will integrate the time bell function in the fingerprint machine, you
will be allowed to schedule bell depend on actual need, at appoint time,
the fingerprint machine will automatically broadcast bell sound that you
are choice, when after duration of the bell, the bell will automatically
stop.
Instruction
Scroll ▲/▼ key to view the bell setting in line by line.
75
TFT Fingerprint V3.2
Scroll PageUp/PageDown key to view the bell setting in page by page.
Press "
" key to begin/end the selected bell.
Press "OK" to set the bell that is your choice, and enter the edition bell.
Bell time: Arrive at this time the equipment will automatically ring bell.
Sound choice: bell sound at scheduled time.
Volumes adjust: Bell sound volume.
Number of times: When ring bell, how many times the bell ring.
Bell condition: Whether or not start this bell.
Scroll the▲/▼key shifts the cursor to input box, set up the value with
the numeric keyboard input,. After the set up, directly press OK or the
key to save the settings and return to preceding interface, press
the ESC key to give up.
4.8 Misc Setting
Set Sleep time, external ring and other parameters for device.
Sleep time: When the device reaches the set timed dormancy under the
76
TFT Fingerprint V3.2
state of not being operated, it will enter dormant state. Press any key or
finger to wake up the device.
External ring: select whether to open external ring or not. (External
ring means the alarm ring is not uttered by the machine itself, but by the
external bell connected with the internal of the machine.)
FP Image: means whether display the fingerprint image on the screen
while registration or verification is being done. There are 4 choices:
display the fingerprint both at registration and verification, display the
fingerprint at registration, display at verification, and no display at
registration and verification.
Power Button: Locked shut-down key, to prevent malicious on-off, you
can select whether to lock the shut-down key or not.
If you select “off”, the machine will be shut down in 3 seconds
after you press the shut-down key.
If you select “on”, pressing the shut-down key will be of no effect.
J Notice: 1. The external ring function requires hardware support. If
necessary, please contact the business represent or technical
support personnel.
2. Only the machine with shut-down key possesses locked
shut-down key.
Instruction
77
TFT Fingerprint V3.2
Scroll the▲/▼key shifts the cursor to input box, set up the value with
the numeric keyboard input,. After the set up, directly press OK or the
key to save the settings and return to preceding interface, press
the ESC key to give up
78
TFT Fingerprint V3.2
5 Time date
5.1 Time and Date settings
It is necessary to set the accurate date and time for each of equipments.
To obtain guarantee for tracking accurate attendance time.
Enter option to set the time and date :
Instruction
Scroll the / key to switch option input box, Scroll▲/▼key to shifts
the cursor input box . set up the value with the numeric keyboard input
After you set up completed, please press "OK" to save this configuration,
press the ESC key to abandon operation and return to the up page
79
TFT Fingerprint V3.2
5.2 Daylight Saving Time
Daylight Saving Time, also known as "daylight saving time system” is a
man-made the local time for saving energy, during the system is used
this unity time known as "daylight saving time." Usually in the early
morning of the summer people will be one hour ahead of time, people
can get up early and early sleep to save lighting to make full use of
resources illumination, save electricity. at autumn fall Then call back
one hour. The different countries have different specific requirements of
daylight saving time.
In order to meet the needs of daylight saving time, we can offer a special
custom features, in XX, XX, XX, XX hours, fast one hour, and by the
XX, XX, XX-XX, then slow one hour .
Note: Daylight Saving Time function only provide by certain models.
Instruction
When the device have this functional, in the time period interface there
will be set up options:
80
TFT Fingerprint V3.2
1) Set Daylight Saving Time option as "NO."
2) Assign Daylight Saving Time start and end times.
For example, setup at 8:00 on April 1, the machines come in the
Daylight Saving Time, the counting time will be ahead for one hour. To
at 8:00 on October 1, equipment returned to normal time.
3) press
and exit.
/ "OK" to save the settings; press the "ESC" does not save
81
TFT Fingerprint V3.2
6 USB Flash disk management
Through the USB flash disk, import the user’s information, the
fingerprint template, the attendance data into and the Time &
Attendance tracking software for processing, transfer the user’s
information and the fingerprint template to other fingerprint equipment.
6.1 Download attendance datum
Save all attendance data in the equipment into the USB flash disk.
Instruction
1) Plug the USB flash disk into the USB slot of the fingerprint machine
through the miniature USB cable.
2)Press “▲” and “▼”to scroll up or down the screen to select the
82
TFT Fingerprint V3.2
“Download Attlog”,
3)Press “ok” to go on downloading data, the equipment prompt "is
downloading the data, please waits... ...” until the equipment prompt
“download attendance data successful" after operation finishes this
interface show as follow.
4) Press “ESC” key to exit initial interface,Take out U flash disk,The
files X_attlog.dat (attendance log), X_oplog .dat (management log), and
X_user will be saved in the USB flash disk(X is a symbol of machine
No.
6.2 Download user’s data
Save all user information and the fingerprint in the equipment in the
USB flash disk.
Instruction
Operation is similar with the attendance data.
Plug the USB flash disk into the USB slot of the fingerprint machine,
Scroll the "▲/▼" key to choose user data you want to download, if
download successfully , the files user.dat (user information) and
template.dat (fingerprint template) will be viewed available
83
TFT Fingerprint V3.2
6.3 Download SMS★
The short message in the equipment will be saved to U flash disk.
Instruction
Plug the u flash disk into the USB slot of fingerprints machines, through
the scroll "▲ / ▼" key to select download short message, after the
download successfully, udata.dat and sms.dat 2 files will be find in the
U flash disk.
6.4 Upload the user data
Upload the user information and the fingerprint which have been saved
in the USB flash disk into the equipment.
Instruction
Plug the USB flash disk into the USB slot of the fingerprint machine,
scroll the "▲/▼" key to choose the user data that you want upload, then
press the OK key, the two files user.dat (user information) and
template.dat (fingerprint template) will be uploaded to the machine . If
there are not two files in the USB flash disk, the prompt "copy file” will
appear
6.5 Upload SMS★
The short message in the U flash disk U will be uploading to equipment.
84
TFT Fingerprint V3.2
instruction
plug the U flash disk into the USB slot of fingerprints machines, then
the scroll "▲ / ▼" key to select users to upload data, after choose ,then
press OK , the udata.dat and sms.dat 2 files in the U flash disk will be
uploaded to the machines.
6.6 Upload the customized picture
Upload the file with JPG picture format which front name include "ad_”
in the USB flash disk into the equipment, after these pictures have been
transfer to the equipment, it will display in the initial window. (Picture
specification, please see appendix 4)
Instruction
Plug the USB flash disk in the USB slot of the fingerprint machine,
scroll the"▲/▼" t key to preview the picture in the USB flash disk then
press the OK key to choose the picture you want to upload ,after if the
prompt “upload successfully” display on the equipment , the file will
85
TFT Fingerprint V3.2
automatically jumps to the next picture. To upload, after upload picture
completed, presses the ESC key to exit.
86
TFT Fingerprint V3.2
7. Automatically test
The equipment provides with the automatic test function to test each
module in the fingerprint machine, help the operator fast check the
module, if the machine breakdown possibly occur. Including TFT screen,
voice prompt, clock, keyboard, and fingerprint sensor test. Choose the
option to test.
Scroll the ▲/▼ key to select the project that want to be test, press the
"OK" key to start
7.1 Test TFT screen
Equipment provide auto-test to check the TFT screen demonstration
effect, through when the screen display in color, entire white, entire
black, you can inspect each place of the screen at this time , whether the
TFT screen demonstrates normally.
87
TFT Fingerprint V3.2
Press “OK” to continue to test whiles the test process, press ESC key to
exit from this test.
7.2 Test pronunciations
The equipment offer auto-test voice prompt effect, through play voice
file in the equipment, check whether the voice file is completed, and the
pronunciation effect is in good. Press "OK" to continue to play voice
while the test process, press ESC key to exit from this test
7.3 Test keyboards
The equipment carries on the automatic detection to each keyboard, tests
each key of keyboard is normal. In the keyboard test window,
stochastically press any key of the keyboard (except the "OK" and
"ESC" key), check whether the key of the keyboard you press accord
with the display on the screen. The key you press display in garnet
color, otherwise the key
from this test
in gray black. Press "ESC" key to exit
7.4 Test fingerprint Sensor
The auto-test fingerprint sensor told user whether the sensor is in normal,
through the test you can examine the picture resolution of the fingerprint,
whether the fingerprint picture is clear, and the screen will real-time
show fingerprint picture that capture from the finger when you place the
fingerprint sensor window. Press ESC key to exit from this test.
88
TFT Fingerprint V3.2
7.5 Real-time clocks
The equipment provides function to test the clock, through to stopwatch
test you will get result about whether the clock is in normal operation or
not.
Press the OK key to start to time, press the OK key again to stop time,
check whether the equipment times are in accurately. Press ESC key to
exit from this test.
89
TFT Fingerprint V3.2
8. Inquiry record
When the fingerprint machine track the staff time & attendance
successfully the record will be saved in, in order to provide the staff
with convenience to know his/her attendance logs, this machine offer
the inquiry record function.
8.1 Inquiry attendance
Depending on the inquiry condition that the user defines, the record that
conforms to the inquiry condition will display on the screen, it is easily
user to view.
Enter the inquiry menu, first input the condition in the blank. Then input
personnel's serial number and the date scope that you want to inquire
1) When the AC.NO that you input is empty, express that all staffs will
90
TFT Fingerprint V3.2
be inquiried
2) Input some AC.NO, then inquiry this staff's attendance record only.
After complete to inquiry these records which meet the inquiry
condition will appear on the screen:
Scroll the ▲/▼key to locate the cursor to the line that you want to view,
press OK key to browse the detailed Time & Attendance log.
For example on May 8 10001 staffs' detailed situations:
91
TFT Fingerprint V3.2
The information of the note display underneath the screen, namely
various letters meaning.
Verification
F: Express the fingerprint verification.
P: Express the password verification.
State
The number is the code of state.
92
TFT Fingerprint V3.2
9. Systems information
Through the system information option, you may know this machine
memory as well as the machine edition information and so on.
9.1 Logs capacity
Through the log capacity you can know the number of users, managers,
registration password in this machine; as well as the machine fingerprint
capacity and the registered fingerprint, the attendance logs capacity and
the memory attendance logs capacity are respectively demonstrated by
the graphic mode, shown as following graphical
93
TFT Fingerprint V3.2
9.2 Equipment information
In the equipment information the machine equipment name, serial
number, version information is available.
94
TFT Fingerprint V3.2
Appendix 1 Getting familiar with keyboard
The equipment keyboard meets with the different function in different
interface, for detail please see the next table.
One model:
key
numeric
keyboard
▲
detailed solution
1, 0 ~ 9, is used in to input the staff to number, numeral
and password so on.
2、in the management user interface digital 0 are " search
user" shortcut key.
1、Upward .
2、shortcut key.
▼
1、Downward .
2、Shortcut key.
1、Revision goal value.
2、Shortcut key
1、Revision current project
2、Shortcut key
1、Shut down key. Press this key least for 3 seconds in the
initial interface to enter the shut down machine state.
2、Shortcut key
1、The backspaces key. If when input AC.NO, password,
system setting value ,if you make the mistake , press
this key to be possible to delete the value ,input it
again.
95
TFT Fingerprint V3.2
2、Shortcut key.
ESC
menu key,confirms the ESC key
1、Cancel operation and return to the preceding menus
2、Press the ESC key to close T9 input method
*
1. in the list window , it is used to page up key
2.shortcut key
3.start the T9 input method
#
1. In the list window, it is used to turn over page key.
2. shortcut key
Two model:
keys
Number
keys
Detail Explanation
1,0 ~ 9, is used to input staff numbers, passwords, and
other figures.
2, In the user management interface the digital 0 button is
used as "View users" shortcuts.
▲
1, upward .
2, shortcuts.
▼
1, down
2, shortcuts.
1, modify the value of the current project.
2, shortcuts.
1, modify the value of the current project.
2, can be used as shortcuts.
1, shutdown button. In the initial interface, hold down this
key for three seconds into the shutdown countdown state.
2, shortcuts.
96
TFT Fingerprint V3.2
1, the Backspace key. If when input AC.NO, password,
system setting value ,if you make the mistake , press
this key to be possible to delete the value ,input it
again.
2, can be used as shortcuts.
Menu Key, confirmed Key
OK
OK Key
ESC
1, cancel operations and return to the previous menu.
2 Press the ESC key to close T9 input method.
*
1. in the list window , it is used to page up key
2.shortcut key
3.start the T9 input method
#
1、 1, the listing pages can be used to turn the pages
bond.
2, can be used as shortcuts.
iClock Access Control Series :
keys
Number
keys
Detail Explanation
1,0 ~ 9, is used to input staff numbers, passwords, and
other figures.
2、 In the user management interface the digital 0 button is
used as "View users" shortcuts.
▲
1, upward .
2, shortcuts.
▼
1, down
2, shortcuts.
1, modify the value of the current project.
97
TFT Fingerprint V3.2
2, shortcuts.
1, modify the value of the current project.
2, shortcuts.
1、Door Bell key
2, shortcuts.
1, the Backspace key. If when input AC.NO, password,
system setting value ,if you make the mistake , press
this key to be possible to delete the value ,input it
again.
2, can be used as shortcuts.
Menu Key, confirmed Key
OK
OK Select characters
ESC
1, cancel operations and return to the previous menu.
2, Press the ESC key to close T9 input method.
Tab
1, Start T9 input method.
2, can be used as shortcuts.
PgUp
PgUp
3. In the list window, it is used to turn over page key.
1、 shortcut key.
1、 in the T9 input method. the Backspace key
2、
keys
Number
keys
can be used as shortcuts.
Detailed Explanation
1,0 ~ 9, is used to input staff numbers, passwords, and other
figures.
2、 In the user management interface the digital 0 button is
used as "View users" shortcuts.
98
TFT Fingerprint V3.2
▲
1, upward to switch options .
2, shortcuts.
▼
1, downward to switch options
2, shortcuts.
1, modify the value of the current project.
2, shortcuts.
1, modify the value of the current project.
2, shortcuts.
Doorbell button
M/OK
ESC
Menu, Enter button
cancel and return to preceding menu
99
TFT Fingerprint V3.2
Appendix 2 T9 input method★
The name of T9 input method is the smart input method; it is famous for
highly effective and quickly inputting the character, this equipment fully
supports the T9 Chinese, the T9 English, and the symbol input. There
are three or four English letters on 0 ~ 9 numeric keyboards of the
machine, for example the numeric keyboard 1 has the A, B, the C three
letters, only input key where this letter locate for the T9 Chinese , Press
the algorithm of the program will automatically combine the legitimate
Pinyin. Then press the numeric key to choose Pinyin for inputting the
Chinese character. The T9 English also comply with the letter
arrangement of English word to input, only press key which inputs this
letter, the program automatically display this key expressed all letters,
press the numeric key to select letter. The T9 input method also may
input some marks. May input the name, the short message content
through the T9 input method user is able to input the name, the short
message content.
T9 input method key distribution and its function:
ESC key
Backspace key
Startup/Switch inputting
Blank Key
100
TFT Fingerprint V3.2
/ :Page up/Down
OK:Choose letter
Take an example for the T9 English input: Input “Arabia "
press the * numeric key to enter the T9 input method.
Press numeric 2
key
Pres numeric key to select
Input the letter you
select.
101
TFT Fingerprint V3.2
If must continue, presses the above method to carry on the input again.
After the input completed, presses the ESC key to exit
102
TFT Fingerprint V3.2
Appendix
3
Multi–combination
Authentication Mode ★
In order to meet the high-security Access Control occasions needs.
Taking into account the use of Access Control, we provide a various
functional verification methods, individuals or groups can be set up
against a variety of types of verification, there are four matching way
types main number (PIN), fingerprints (FP), password (PW) and RF, not
only can achieve alone fingerprint, a separate password, ID, and
fingerprint verification, could also achieve fingerprint + password,
password + fingerprint+ card, numbers + fingerprint + password
combination verification methods.
Note: 1) Mifare in specific processing can be regarded as RF,if the
verification involved in the type of Mifare card, only use the function of
machines Mifare cards may.
2) Except certain specific types of machines, other machines only
fingerprint verification and password verification test two types,
machines with Mifare card functions, also Mifare card verification.
provided
"/" Or , "&" and ,"←" confirmed, (Enter).
The following table describes that the user is registered by fingerprint
cards and a password; the following verification maybe is used in future
multi- combination verification:
103
TFT Fingerprint V3.2
Type
Description
FP
only FP fingerprint verification
1) PIN + FP (1:1 verification)
2) FP (1: N verification)
3) RF + FP (1:1 verification)
PIN
only PIN numbers verification
1)PIN+“←”
PW
only password verification
1) PIN+“←”+PW
2) RF+PW
RF
only RF Card Verification
1)RF+FP
FP/PW
FP / PW fingerprint or password verification
1) PIN+FP(1:1)
2)FP(1:N)
3)PIN+“←”+PW
4)RF+PW
FP/RF
fingerprinting or RF verification
1)PIN+FP(1:1)
2)FP(1:N)
3)RF+FP
PW/RF
password or RF verification
1) RF+FP
2) PIN+“←”+PW
FP/PW/RF
fingerprint or password or RF verification
1) PIN+FP(1:1)
2) FP(1:N)
3) PIN+PW
104
TFT Fingerprint V3.2
4) RF+FP
FP&PIN
PIN number and fingerprint verification
1)PIN+“←”+FP(1:1)
1) RF +“←”+FP(1:1)
FP&PW
fingerprint and password verification
1) FP(1:N)+PW+“←”
2) PIN+FP(1:1)+PW+“←”
3) RF+PW +“←”+ FP(1:1)
FP&RF
RF and fingerprint verification
1)RF+FP(1:1)
2)FP(1:N)+RF
3)PIN+FP(1:1)+RF
PW&RF
FP&PW&RF
passwords and RF verification
1) RF+PW
2) PIN+“←”+PW+RF
fingerprinting, passwords and RF Verification
1) FP(1:N)+PW+RF
2) PIN+FP(1:1)+PW+RF
3) RF+ PW+ FP(1:1)
FP&PIN&PW
fingerprints numbers and passwords
1) PIN+“←”+PW+FP(1:1)
2) RF+“←”+PW+“←”+FP(1:1)
FP&RF/PIN
fingerprint and RF Verification or fingerprinting
and numbers verification
1)RF+FP(1:1)
2)FP(1:N)+RF
3)PIN+“←”+FP(1:1)
105
TFT Fingerprint V3.2
When enroll user, registered fingerprint card or a password
and the number cards, the validation process are shown as the
following table:
Type
Description
Registration password
FP
only
verification
fingerprint
1.PIN+FP(1:1
verification)
2FP (1: N verification)
3)RF+FP(1:1)
PIN
Failed to pass
verification numbers only
1)PIN+“←”
PW
Registration fingerprint
1)PIN+“←”
only
verification
password
Password wrong
1) PIN+“←”+PW
2)RF+PW
RF
only
RF
Verification
Card
1)RF+FP
FP/PW
1)RF
fingerprint or password
verification
1) PIN+FP(1:1)
1) PIN+“←”+PW
2) FP(1:N)
2) RF+PW
3) PIN+“←”+ FP(1:1)
4) RF+FP(1:1)
FP/RF
fingerprinting
verification
or
106
RF
TFT Fingerprint V3.2
1)RF
1) PIN+FP(1:1)
2) FP(1:N)
3) RF+FP
PW/RF
FP/PW/RF
password
verification
or
RF
1) RF
1) PIN+”←”+PW
2) PIN+“←”+RF
2) RF
fingerprint or password or
RF verification
1) PIN+FP(1:1)
1) PIN+”←”+PW
2) FP(1:N)
2) RF
3) PIN+“←”+ FP(1:1)
4) RF+FP
FP&PIN
PIN
number
and
fingerprint verification
1) PIN+“←”+FP(1:1)
Failed to pass
2) RF+ PIN+“←”+FP(1:1)
FP&PW
fingerprint and password
verification
Failed to pass
FP&RF
Failed to pass
RF and fingerprint
verification
Failed to pass
1) RF+FP(1:1)
2) FP(1:N)+RF
3) PIN+FP(1:1)+RF
PW&RF
passwords
verification
and
107
RF
TFT Fingerprint V3.2
Failed to pass
FP&PW&RF
1) RF+PW
2) PIN+“←”+PW+RF
fingerprinting, passwords
and RF Verification
Failed to pass
FP&PIN&PW
Failed to pass
fingerprints, PIN numbers
and passwords
Failed to pass
FP&RF/PIN
Failed to pass
fingerprint and RF or the
fingerprinting and PIN
1)RF+FP(1:1)
2)FP(1:N)+RF
3)PIN+“←”+FP(1:1)
Failed to pass
Note: 1) When users register a number of cards and the fingerprint in
the equipment at the same time, on the table in the RF test only punch
the card, no need then fingerprints.
2) Multi -combination verification methods, it is better to register users
use by fingerprints and passwords, or otherwise never pass verification.
Example: A user using a fingerprint registration and the verification
is PW way, the user fail to pass.
108
TFT Fingerprint V3.2
Appendix 4 Quickly inquiry the staff
attendance logs
In order to help ordinary user to view his/her Time & Attendance record
at same day, whether forget clock-in or occur error, should well inform
the manager that the attendance record is in abnormal
Instruction
After the user verify fingerprint or the password successfully in 10
seconds, the pressed
same day.
key to be bale to show this staff all records in
For example: the staff, who’s AC.NO is 1, match the fingerprint
successfully, then the press
key, you will be able to view his /her
Time & Attendance record same day.
109
TFT Fingerprint V3.2
Scroll the ▲/▼ key to browse the Time & Attendance record line by
line
Press PageUp/PageDown key page by page to browse the Time
&attendance record;
Press OK or
key inquiry detailed.
Press ESC key to return the initial interface.
110
TFT Fingerprint V3.2
Appendix 5 The rule about the advertising
pictures
1. The format of the pictures must be the JPG , the fingerprint machine
do not support other format all
2.The header of advertising pictures filename must be " ad_0 ~ad_10"
as head. For instance ad_1.jpg is legitimate.
3. Each picture size does not surpass over 50K, otherwise unable to
upload it.
4. Pictures resolution are 320 widths and 210 high, it is better to surpass
or smaller than this resolution.
5. Do not more than 10 sheet of advertising pictures in the fingerprint
machine.
111
TFT Fingerprint V3.2
Appendix 6
function ★
anti-pass
back
[Summarize]
If you want to prevent following occasion occur, a people follow the
others to enter the building, but he/she do not go out with people
together, and potential safety problems arise, this anti-pass back feature
provide that, unless the access records match, the door is unable to be
open.
This feature requires two machines work with together. A machine is
installed in the building (the "host"), other machine is installed in the
outside (hereinafter referred to as "client"). Between the two machines
connect through Wiegand communications signals.
[Principle]
The host own Wiegand In, the client with Wiegand Out function.
Connect Wiegand Out signal of the client machine to the Wiegand In of
host machine, Wiegand signal that output from the client machine ,send
it to host, must be without machine No., the number in the host must
exist, that is the function of two anti-pass back the machines of users
And the host must match.
[Instruction]
According to the most recent user accessed records to determine
whether anti-pass back, accessed logs must be matching. There are
IN ,Out , In-Out to anti-pass back function.
112
TFT Fingerprint V3.2
When the host is set to “Out anti-pass back," If a user want to
normally access or out, then the last record of the user must be
"income" , otherwise it is allowed to go out., system will be "anti-pass
back to refuse going out." For example: a user's most recent recording is
"in", the second is record his income. The record must be the third to
second, is out of matching, and so on. (Note, if there is no record of
prior customers, and that he can to, not out)
When the host is set to "In anti-pass back," If a user want to normally
access or out , then the last record of user must be "to" can not be out.
As long as it is to find the records system will be "anti-pass back
refused." (Note, if there is no record of prior customers, he can produce
and can not)
When the host is set to "access to anti-pass back," If a user access to
normal, then the user is the most recent record "to" and "income", the
next record is to be "into" and "out", access must be matching.
[Instruction]
1)the choice of models
Host: the machine with wiegand in function . Except F10
Client the machine: the machine with Wiegand Out function.
2)Menu setting
Anti-pass back direction
Choice of Anti-pass back mode. There are three options: In pass
back, Out anti-pass back, None.
Out anti-pass back: Only the user's last recorded is IN , can open
the door.
In the anti-pass back: Only the user's records in the last time is out,
in order to open the door.
Device state
There are three options: control in, control out, None.
113
TFT Fingerprint V3.2
Control In: Set the value, the machine records to verify the entry records.
Control out: Set the value, the machine records to verify the records out.
None: Set the value, that is, the closure of the anti-pass back function.
Scroll ▲ / ▼ key to switch input box option, scroll / to change
settings, after set is complete, press OK to save your settings, press
"ESC" exit from the set.
3) Configure weigand output format
Two machine communication with the Wiegand signal. enter the
menu of Machines -> Communications Settings -> Wiegand
settings or enter the software -> basic settings -> equipment
management -> weigand, "defined format" to "wiegand26 without
device ID".
4) User registration
This user must exist in the client the host machine together, and
users No. must be consistent . Therefore, need to register users in
the host and client machine at the same time.
114
TFT Fingerprint V3.2
5) Wiring instruction
The communication between the host and client machine visa the
Wiegand, the wiring shows as follow:
Host machine client machine
IND0 <-----> WD0
IND1 <-----> WD1
GND <-----> GND
115
TFT Fingerprint V3.2
Appendix 7 Photo ID ★
Some equipment the Photo ID function provide , Photo ID feature is that
when a user go to performances authentication, the show, names and
other information screen , users photo which is stored in the U flash disk
also appear on the screen.
[Steps]
1, if there is not SD card in the equipment, the steps are as follows:
1) Create a photo folder in the U flash disk, which is named as photo,
the user's photos is stored in the folder.
2) User’s photo must be in the JPG format, the file name must be the
name of working No.. For example: The No. 154 for the corresponding
photos of the user names would be 154. Jpg.
3) plug U flash disk into the USB slot of fingerprint machine, then
proceed to verify that the user can display photos.
Note: 1) the User name is not allowed to exceed eight figures.
116
TFT Fingerprint V3.2
2), while user goes on authentication, the U flash disk have been planted
on the device.
2, If the device with SD card, the steps are as follows:
1) Create a photo folder in the U flash disk, which is named as photo,
the user's photos is stored in the folder..
2) User’s Photo must be in the JPG format, the file name must be the
name of, the User name can not be more than eight figures. For example:
The No. 154 for the corresponding photos of the user names would be
154. Jpg.
3) plug U-flash disk into the USB slot of fingerprint machine, enter the
U flash disk-management -> upload data -> upload user’s photos.
Operation is same with a 6.6 upload custom picture.
4) Download, enter the U flash disk -management -> Download ->
download users pictures, a folder will be automatically build on the U
flash disk -called photo , users download photos will be all existence on
this folder.
117
TFT Fingerprint V3.2
RoHS Compliance
•The standard of environmental protection of these products in this
statement refers to safety deadline under the conditions of provisions
using the product no leakage of toxic or hazardous substances harmful
to.
• The standard of environmental protection products by the deadline
does not include the batteries or be easy to wear and tear of the regular
replacement parts. The deadline for the use of environmentally friendly
batteries is five years.
Table of hazardous substances' name and concentration
Component
Name
Hazardous substances’ name
( Pb
)
( Hg
)
(Cd)
( Cr6+
)
( PBB
)
resistors
×
○
○
○
○
○
SMD
capacitor
×
○
○
○
○
○
SMD
inductors
×
○
○
○
○
○
SMD diode
×
○
○
○
○
○
PCB
×
○
○
○
○
○
Buzzer
×
○
○
○
○
○
Adopter
×
○
○
○
○
○
Screws
○
○
○
×
○
(PBDE)
○
○:Indicates that this toxic or hazardous substance contained in all of the
homogeneous materials for this part is below the limit requirement in
SJ/T11363-2006.
X: Indicates that this toxic or hazardous substance contained in at least
118
TFT Fingerprint V3.2
one of the homogeneous materials used for this part is above the limit
requirement in SJ/T11363-2006.
Note:80% component of this product are made from non-toxic or
hazardous substance, Applications of hazardous substances in this
device are required to achieve its intended uses, due to lack of
reasonably (economically or technically) available substitutes. Indicates
that the concentration of the hazardous
119
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertisement