Untitled - Touch panel, touch screen, тач скрин

Untitled - Touch panel, touch screen, тач скрин
Page 3 of 37
Report No.: 17036459 001
List of Attachments (including a total number of pages in each attachment):
-
Attachment 1: National differences (46 pages)
-
Attachment 2: Photo documentation (8 pages)
Summary of testing:
Tests performed (name of test and test clause):
The tests were carried out under the most unfavorable
combination within the manufacturer’s operating specifications of
the following parameters:
-supplied by approved switching adapter (see appended table
1.5.1 for details);
-operating temperature, Max. ambient temperature 40°C declared
by the client;
-operating mode: continuous;
-operating load: normal load;
-according to the client request, the open frame EUT is sealed
in a plastic bag during heating test, to simulate the most unfavourable condition of the final equipment.
The critical tests were performed for this equipment included
clauses:
name of test
test clause number
Input Current Test
1.6.2
Durability of Marking Test
1.7.11
Limited Circuit Current
2.4.2
Working voltage measurement
2.10.2
Maximum Temperature Test
4.5.2
Fault Condition Test
5.3
The EUT passed the test.
TRF No. IEC60950_1C
Testing location:
All tests as described in Test Case and
Measurement Sections were
performed at the laboratory described
on page 2
Page 4 of 37
Report No.: 17036459 001
Summary of compliance with National Differences
List of countries addressed:
EU Group Differences, EU Special National Conditions, EU A-Deviations, AT, BE, CH, CN*, CZ, DE, DK,
ES, FI, FR, GB, GR, HU, IE, IL, IT, JP#, KR, NL, NO, PL, SE, SI, SK
Explanation of used codes: AT=Austria, BE=Belgium, CH=Switzerland, CN=China, CZ=Czech Republic,
DE=Germany, DK=Denmark, ES=Spain, FI=Finland, FR=France, GB=United Kingdom, GR=Greece,
HU=Hungary, IE=Ireland, IL=Israel, IT=Italy, JP=Japan, KR=Korea, NL=The Netherlands, NO=Norway,
PL=Poland, SE=Sweden, SI=Slovenia, SK=Slovakia
For National Differences see end of this test report.
* National differences to IEC 60950-1:2005 evaluated.
# National differences to IEC 60950-1:2001 evaluated.
The product fulfils the requirements of EN 60950-1: 2006 + A11:2009 + A1:2010 + A12:2011.
Copy of marking plate
Note: The above label is a draft of an artwork of marking plate pending approval by National Certification
Bodies and it shall not be affixed to products prior to such an approval.
TRF No. IEC60950_1C
Page 5 of 37
Report No.: 17036459 001
Test item particulars ...................................................:
Equipment mobility ..................................................... : [] movable [] hand-held
[] transportable
[] stationary [x] for building-in [] direct plug-in
Connection to the mains ............................................ : [] pluggable equipment [] type A [] type B
[] permanent connection
[] detachable power supply cord
[] non-detachable power supply cord
[x] not directly connected to the mains
Operating condition .................................................... : [x] continuous
[] rated operating / resting time:
Access location ......................................................... : [x] operator accessible
[] restricted access location
Over voltage category (OVC) .................................... : [] OVC I [] OVC II [] OVC III [] OVC IV
[x] other: no direct mains connection
Mains supply tolerance (%) or absolute mains supply
values ........................................................................ : N/A
Tested for IT power systems .................................... : [] Yes
[x] No
IT testing, phase-phase voltage (V) .......................... : N/A
Class of equipment ................................................... : [] Class I [] Class II
[] Not classified
[x] Class III
Considered current rating of protective device as part
of the building installation (A) .................................... : <16A
Pollution degree (PD) ................................................ : [] PD 1
[x] PD 2
[] PD 3
IP protection class ..................................................... : IP20
Altitude during operation (m) ..................................... : <2000m
Altitude of test laboratory (m) .................................... : <1000m
Mass of equipment (kg) ............................................ : 4.42 Kg
Possible test case verdicts:
- test case does not apply to the test object ................. : N/A
- test object does meet the requirement ....................... : P (Pass)
- test object does not meet the requirement................. : F (Fail)
Testing .......................................................................... :
Date of receipt of test item ............................................ : 22 April, 2011(CB report 17020672 001);
10 March 2014
Date(s) of performance of tests .................................... : May - June. 2011(CB report 17020672 001);
16 April, 2014
TRF No. IEC60950_1C
Page 6 of 37
Report No.: 17036459 001
General remarks:
The test results presented in this report relate only to the object tested.
This report shall not be reproduced, except in full, without the written approval of the Issuing testing
laboratory.
"(see Enclosure #)" refers to additional information appended to the report.
"(see appended table)" refers to a table appended to the report.
Throughout this report a
comma /
point is used as the decimal separator.
Manufacturer’s Declaration per sub-clause 6.2.5 of IECEE 02:
The application for obtaining a CB Test Certificate
includes more than one factory location and a
declaration from the Manufacturer stating that the
sample(s) submitted for evaluation is (are)
representative of the products from each factory
has been provided.................................................. :
Yes
Not applicable
When differences exist; they shall be identified in the General product information section.
Name and address of factory (ies) ................... : KeeTouch Co., Ltd.
1/F, 3/F, 4/F of Building 9 Luck-King Science & Industry
Park Gongyedong Road, Longhua, Baoan Shenzhen
P.R. China
General product information:
1. The product is a touch monitor without enclosure which could be used build in cabinet or enclosure
in end product and named as open frame LCD monitor with touch screen.
2. According to the client’s request, as the final using condition is not defined, to simulate the most
unfavorable condition of the final equipment, the EUT is sealed in a plastic bag during the heating
test.
3. The model is a Class III product, powered by an approved external adapter (class I). The output of
the external adapter complies with limited power source.
4. The touch screen is controlled by the signal from the Serial port or the USB port. The Serial port
and the USB port can not be functional at the same time. If Serial port is chosen to connect the
touch screen, USB port is disabled, and vice versa. The USB port is chosen during the test if not
specified.
5. The model has an internal inverter for CCFL backlight of the LCD panel. The inverter output is
916V in CN3 connector, 898V in CN2 connector, be evaluated to clause 2.4 of the standard as
those would be accessed by operator.
6. There are two output connectors on the main board, VGA and DVI.
7. The specified maximum ambient temperature is +40 °C.
This report is based on TÜV Rheinland CB reports 17020672 001 issued on 17. 06, 2011 for standard
upgrade, in addition to:
1. Replace external AC adapter KPA-050F(Channel Well Technology Co., Ltd.) by PDN-48-48A
(Shenzhen Meikai Electronics Stock Co., Ltd.);
2. Add table 2.10.2 as the working voltage of inverter output given in table 2.4.2 which is not suitable
for this clause;
3. Remove national differences of Australia, Canada and United States of America, add national
difference of China, Japan;
4. Replace the name and address of applicant, manufacturer and factory, see below for details.
Original name and adress of applicant, manufacturer and factory:
Shenzhen K&JAD Technology Co., Ltd.
1-4/F Of Building 9 Luck-King Science & Industry Park Gongyedong Road Longhua, Baoan,
Shenzhen P.R. China
TRF No. IEC60950_1C
Page 7 of 37
Report No.: 17036459 001
After Revised:
KeeTouch Co., Ltd.
1/F, 3/F, 4/F of Building 9 Luck-King Science & Industry Park Gongyedong Road, Longhua, Baoan
Shenzhen P.R. China
For the above described change(s) the following was considered to be necessary:
Change
Testing
Comments
1
1.6.2
See appended table 1.5.1 in bold for the new
component.
2
N/A
Re-evaluate clause 2.10.2, see clause 2.10.2 for details.
3
N/A
See attachment 1 for details
4
N/A
See page 1, 6 for details
Definition of variable(s):
Variable:
Range of variable:
Content:
KXT-ABCY-ZZZ
X
D or O
For product colour, no technical difference.
A, B, C
0-9
For product internal code, no technical difference.
Y
G, C, or W
For sales area, no technical difference.
ZZZ
001-999
For customer code, no technical difference.
Abbreviations used in the report:
- normal conditions
- functional insulation
- double insulation
- between parts of opposite
polarity
N.C.
OP
DI
- single fault conditions
- basic insulation
- supplementary insulation
S.F.C
BI
SI
BOP
- reinforced insulation
RI
Indicate used abbreviations (if any)
TRF No. IEC60950_1C
Page 8 of 37
Report No.: 17036459 001
IEC 60950-1
Clause
Requirement + Test
Result - Remark
Verdict
1
GENERAL
P
1.5
Components
P
1.5.1
General
P
Comply with IEC 60950 or relevant component
standard
(see appended table 1.5.1)
P
1.5.2
Evaluation and testing of components
Components which are
certified to IEC and/or national
standards are used correctly
within their ratings.
Components not covered by
IEC standards are tested
under the conditions present
in the equipment.
P
1.5.3
Thermal controls
No thermal controls.
N/A
1.5.4
Transformers
Considered in approved
external adapter.
N/A
1.5.5
Interconnecting cables
No cable provided with the
unit.
N/A
1.5.6
Capacitors bridging insulation
Considered in approved
external adapter.
N/A
1.5.7
Resistors bridging insulation
Considered in approved
external adapter.
N/A
1.5.7.1
Resistors bridging functional, basic or
supplementary insulation
N/A
1.5.7.2
Resistors bridging double or reinforced insulation
between a.c. mains and other circuits
N/A
1.5.7.3
Resistors bridging double or reinforced insulation
between a.c. mains and antenna or coaxial cable
N/A
1.5.8
Components in equipment for IT power systems
No such components.
N/A
1.5.9
Surge suppressors
Considered in approved
external adapter.
N/A
1.5.9.1
General
N/A
1.5.9.2
Protection of VDRs
N/A
1.5.9.3
Bridging of functional insulation by a VDR
N/A
1.5.9.4
Bridging of basic insulation by a VDR
N/A
1.5.9.5
Bridging of supplementary, double or reinforced
insulation by a VDR
N/A
1.6
Power interface
1.6.1
AC power distribution systems
TRF No. IEC60950_1C
P
Unit is not directly connected
to the AC mains.
N/A
Page 9 of 37
Report No.: 17036459 001
IEC 60950-1
Clause
Requirement + Test
Result - Remark
Verdict
1.6.2
Input current
(see appended table 1.6.2)
P
1.6.3
Voltage limit of hand-held equipment
This appliance is not handheld equipment.
N/A
1.6.4
Neutral conductor
No primary circuit.
N/A
1.7
Marking and instructions
1.7.1
Power rating
See below.
Rated voltage(s) or voltage range(s) (V) ............... :
See copy of marking plate in
page 4
N/A
Symbol for nature of supply, for d.c. only............... :
See copy of marking plate in
page 4
N/A
P
Rated frequency or rated frequency range (Hz) ... :
P
N/A
Rated current (mA or A) ........................................ :
See copy of marking plate in
page 4
N/A
ManuFacturer’s name or trade-mark or
identification mark ................................................. :
The manufacturer’s name on
the label in page 4
P
Model identification or type reference ................... :
See copy of marking plate in
page 4
P
Symbol for Class II equipment only ...................... :
N/A
Other markings and symbols ................................ :
Additional symbol or marking
does not give rise to
misunderstanding.
P
1.7.2
Safety instructions and marking
English safety instruction
provided.
P
1.7.2.1
General
1.7.2.2
Disconnect devices
N/A
1.7.2.3
Overcurrent protective device
N/A
1.7.2.4
IT power distribution systems
N/A
1.7.2.5
Operator access with a tool
No such access required.
N/A
1.7.2.6
Ozone
Ozone not used or generated.
N/A
1.7.3
Short duty cycles
Equipment is designed for
continuous operation.
N/A
1.7.4
Supply voltage adjustment ................................... :
Single input voltage range
without adjustment.
N/A
P
Methods and means of adjustment; reference to
installation instructions ......................................... :
N/A
1.7.5
Power outlets on the equipment .......................... :
No power outlets provided.
N/A
1.7.6
Fuse identification (marking, special fusing
characteristics, cross-reference) .......................... :
Considered in approved
external adapter.
N/A
1.7.7
Wiring terminals
See below.
N/A
TRF No. IEC60950_1C
Page 10 of 37
Report No.: 17036459 001
IEC 60950-1
Clause
Requirement + Test
Result - Remark
Verdict
1.7.7.1
Protective earthing and bonding terminals ........... :
No earthing terminals and
bonding terminals
N/A
1.7.7.2
Terminals for a.c. mains supply conductors
Not connected to a.c. mains
N/A
1.7.7.3
Terminals for d.c. mains supply conductors
Not connected to d.c. mains
N/A
1.7.8
Controls and indicators
See below
N/A
1.7.8.1
Identification, location and marking ...................... :
1.7.8.2
Colours ................................................................ :
1.7.8.3
Symbols according to IEC 60417 ......................... :
1.7.8.4
Markings using figures ....................................... :
1.7.9
Isolation of multiple power sources ..................... :
1.7.10
Thermostats and other regulating devices .......... :
No such components.
1.7.11
Durability
The label was subjected to
the permanence of marking
test. The label was rubbed
with cloth soaked with water
for 15 sec. and then again for
15 sec. with the cloth soaked
with petroleum spirit.
N/A
No safety related colour used.
N/A
N/A
No figures used.
N/A
N/A
N/A
P
After this test there was no
damage to the label. The
marking on the label did not
fade. There was no curling or
lifting of the label edge.
1.7.12
Removable parts
None.
N/A
1.7.13
Replaceable batteries ......................................... :
No batteries.
N/A

Language(s) .........................................................:
1.7.14
Equipment for restricted access locations ........... :
2
PROTECTION FROM HAZARDS
P
2.1
Protection from electric shock and energy hazards
P
2.1.1
Protection in operator access areas
Only SELV signal interface
accessible by operator.
P
2.1.1.1
Access to energized parts
No hazardous voltage inside,
class III product
P
2.1.1.2
Equipment not intended for
installation in restricted access
locations.
N/A
Test by inspection ................................................. :
N/A
Test with test finger (Figure 2A) ............................ :
N/A
Test with test pin (Figure 2B) ................................ :
N/A
Test with test probe (Figure 2C) ........................... :
N/A
Battery compartments
TRF No. IEC60950_1C
No battery compartment.
N/A
Page 11 of 37
Report No.: 17036459 001
IEC 60950-1
Clause
2.1.1.3
Requirement + Test
Access to ELV wiring
Result - Remark
No ELV wiring in operator
accessible area.
Verdict
N/A

Working voltage (Vpeak or Vrms); minimum
distance through insulation (mm)
2.1.1.4
Access to hazardous voltage circuit wiring
No hazardous voltage wiring in
operator accessible area.
N/A
2.1.1.5
Energy hazards ..................................................... :
Supplied by SELV having a
energy level less than 240VA
P
2.1.1.6
Manual controls
No manual controls.
N/A
2.1.1.7
Discharge of capacitors in equipment
Considered in approved
external adapter.
N/A

Measured voltage (V); time-constant (s) ................ :
2.1.1.8
Energy hazards – d.c. mains supply
N/A
a) Capacitor connected to the d.c. mains supply .. :
N/A
b) Internal battery connected to the d.c. mains
supply .................................................................... :
N/A
2.1.1.9
Audio amplifiers .................................................... :
N/A
2.1.2
Protection in service access areas
No service access area.
N/A
2.1.3
Protection in restricted access locations
Equipment not intended for
installation in restricted access
locations
N/A
2.2
SELV circuits
2.2.1
General requirements
See below
P
2.2.2
Voltages under normal conditions (V) ................... :
42.4V peak or 60V d.c. are
not exceeded in SELV circuit
under normal operation.
P
2.2.3
Voltages under fault conditions (V) ....................... :
Considered in approved
external adapter.
2.2.4
Connection of SELV circuits to other circuits ...... :
Connect to SELV circuit and
Limited current circuit.
2.3
TNV circuits
P
N/A
P
N/A
No TNV circuits, requirements not applicable to the evaluated product.
2.3.1
Limits
N/A
Type of TNV circuits ............................................... :

2.3.2
Separation from other circuits and from accessible
parts
N/A
2.3.2.1
General requirements
N/A
2.3.2.2
Protection by basic insulation
N/A
TRF No. IEC60950_1C
Page 12 of 37
Report No.: 17036459 001
IEC 60950-1
Clause
Requirement + Test
Result - Remark
Verdict
2.3.2.3
Protection by earthing
N/A
2.3.2.4
Protection by other constructions .......................... :
N/A
2.3.3
Separation from hazardous voltages
N/A

Insulation employed ............................................... :
2.3.4
Connection of TNV circuits to other circuits
N/A

Insulation employed ............................................... :
2.3.5
Test for operating voltages generated externally
2.4
Limited current circuits
N/A
P
Applied for inverter output 916V in CN3 connector, 898V in CN2 connector as that
would be accessed by operator (see appended table 2.4.2)
2.4.1
General requirements
See below
P
2.4.2
Limit values
(see appended table 2.4.2)
P
Frequency (Hz) ...................................................... :
(see appended table 2.4.2)

Measured current (mA) .......................................... :
(see appended table 2.4.2)

Measured voltage (V)............................................. :
(see appended table 2.4.2)

Measured circuit capacitance (nF or µF) ............... :
< 45 µC

2.4.3
Connection of limited current circuits to other
circuits
Only intended to be
connected with SELV circuits.
P
2.5
Limited power sources
N/A
Requirement not applicable to the evaluated product. Considered for approved
external adapter.
2.6
a) Inherently limited output
N/A
b) Impedance limited output
N/A
c) Regulating network limited output under normal
operating and single fault condition
N/A
d) Overcurrent protective device limited output
N/A
Max. output voltage (V), max. output current (A),
max. apparent power (VA) ..................................... :

Current rating of overcurrent protective device (A)

Provisions for earthing and bonding
P
Class III equipment.
2.6.1
Protective earthing
N/A
2.6.2
Functional earthing
N/A
2.6.3
Protective earthing and protective bonding
conductors
N/A
TRF No. IEC60950_1C
Page 13 of 37
Report No.: 17036459 001
IEC 60950-1
Clause
Requirement + Test
2.6.3.1
General
2.6.3.2
Size of protective earthing conductors
Result - Remark
N/A
N/A
2

Rated current (A), cross-sectional area (mm ),
AWG ...................................................................... :
2.6.3.3
Verdict
Size of protective bonding conductors
N/A
2
Rated current (A), cross-sectional area (mm ),
AWG ...................................................................... :

2.6.3.4
Resistance of earthing conductors and their
terminations; resistance (Ω), voltage drop (V), test
current (A), duration (min) ...................................... :
N/A
2.6.3.5
Colour of insulation ................................................ :
N/A
2.6.4
Terminals
N/A
2.6.4.1
General
N/A
2.6.4.2
Protective earthing and bonding terminals
N/A
Rated current (A), type, nominal thread diameter
(mm)....................................................................... :

2.6.4.3
Separation of the protective earthing conductor from
protective bonding conductors
N/A
2.6.5
Integrity of protective earthing
N/A
2.6.5.1
Interconnection of equipment
N/A
2.6.5.2
Components in protective earthing conductors and
protective bonding conductors
N/A
2.6.5.3
Disconnection of protective earth
N/A
2.6.5.4
Parts that can be removed by an operator
N/A
2.6.5.5
Parts removed during servicing
N/A
2.6.5.6
Corrosion resistance
N/A
2.6.5.7
Screws for protective bonding
N/A
2.6.5.8
Reliance on telecommunication network or cable
distribution system
2.7
Overcurrent and earth fault protection in primary circuits
No TNV circuit.
N/A
N/A
No primary circuit, requirement not applicable to the evaluated product
2.7.1
Basic requirements
N/A
Instructions when protection relies on building
installation
N/A
2.7.2
Faults not simulated in 5.3.7
N/A
2.7.3
Short-circuit backup protection
N/A
2.7.4
Number and location of protective devices ........... :
N/A
2.7.5
Protection by several devices
N/A
TRF No. IEC60950_1C
Page 14 of 37
Report No.: 17036459 001
IEC 60950-1
Clause
Requirement + Test
Result - Remark
Verdict
2.7.6
Warning to service personnel ................................ :
N/A
2.8
Safety interlocks
N/A
2.8.1
General principles
N/A
2.8.2
Protection requirements
N/A
2.8.3
Inadvertent reactivation
N/A
2.8.4
Fail-safe operation
N/A
2.8.5
Moving parts
N/A
2.8.6
Overriding
N/A
2.8.7
Switches and relays
N/A
2.8.7.1
Contact gaps (mm) ............................................... :
N/A
2.8.7.2
Overload test
N/A
2.8.7.3
Endurance test
N/A
2.8.7.4
Electric strength test
N/A
2.8.8
Mechanical actuators
N/A
2.9
Electrical insulation
P
2.9.1
Properties of insulating materials
2.9.2
Humidity conditioning
Function insulation
Considered.
P
N/A
Relative humidity (%), temperature (°C) ......... ...... :

2.9.3
Grade of insulation
P
2.9.4
Separation from hazardous voltages
2.10
N/A
Method(s) used ..................................................... :

Clearances, creepage distances and distances through insulation
P
Supplied by SELV, and functional insulation inside the unit, requirements not
applicable, see clause 5.3.4
2.10.1
General
2.10.1.1
Frequency ............................................................. :
2.10.1.2
Pollution degrees ................................................... :
See Test item particulars
P
2.10.1.3
Reduced values for functional insulation
See 5.3.4c)
P
2.10.1.4
Intervening unconnected conductive parts
N/A
2.10.1.5
Insulation with varying dimensions
N/A
2.10.1.6
Special separation requirements
N/A
2.10.1.7
Insulation in circuits generating starting pulses
N/A
TRF No. IEC60950_1C
See below
P
N/A
Page 15 of 37
Report No.: 17036459 001
IEC 60950-1
Clause
Requirement + Test
Result - Remark
Verdict
2.10.2
Determination of working voltage
2.10.2.1
General
Applied for inverter output
2.10.2.2
RMS working voltage
Peak working voltage
measured
2.10.2.3
Peak working voltage
See table 2.10.2
2.10.3
Clearances
N/A
2.10.3.1
General
N/A
2.10.3.2
Mains transient voltages
N/A
a) AC mains supply ............................................... :
N/A
b) Earthed d.c. mains supplies .............................. :
N/A
c) Unearthed d.c. mains supplies .......................... :
N/A
d) Battery operation ............................................... :
N/A
2.10.3.3
Clearances in primary circuits
N/A
2.10.3.4
Clearances in secondary circuits
N/A
2.10.3.5
Clearances in circuits having starting pulses
N/A
2.10.3.6
Transients from a.c. mains supply ........................ :
N/A
2.10.3.7
Transients from d.c. mains supply ........................ :
N/A
2.10.3.8
Transients from telecommunication networks and
cable distribution systems ..................................... :
N/A
2.10.3.9
Measurement of transient voltage levels
N/A
a) Transients from a mains supply
N/A
For an a.c. mains supply ....................................... :
N/A
For a d.c. mains supply ......................................... :
N/A
b) Transients from a telecommunication network :
N/A
2.10.4
Creepage distances
N/A
2.10.4.1
General
N/A
2.10.4.2
Material group and comparative tracking index
N/A
CTI tests ................................................................. :
P
P
N/A
P

2.10.4.3
Minimum creepage distances
N/A
2.10.5
Solid insulation
N/A
2.10.5.1
General
N/A
2.10.5.2
Distances through insulation
N/A
2.10.5.3
Insulating compound as solid insulation
N/A
2.10.5.4
Semiconductor devices
N/A
2.10.5.5.
Cemented joints
N/A
TRF No. IEC60950_1C
Page 16 of 37
Report No.: 17036459 001
IEC 60950-1
Clause
Requirement + Test
Result - Remark
Verdict
2.10.5.6
Thin sheet material – General
N/A
2.10.5.7
Separable thin sheet material
N/A
Number of layers (pcs) ........................................... :

2.10.5.8
Non-separable thin sheet material
N/A
2.10.5.9
Thin sheet material – standard test procedure
N/A
Electric strength test
2.10.5.10
Thin sheet material – alternative test procedure
Electric strength test

N/A

2.10.5.11
Insulation in wound components
N/A
2.10.5.12
Wire in wound components
N/A
Working voltage .................................................... :
N/A
a) Basic insulation not under stress ...................... :
N/A
b) Basic, supplementary, reinforced insulation ...... :
N/A
c) Compliance with Annex U ................................. :
N/A
Two wires in contact inside wound component;
angle between 45° and 90° ................................... :
N/A
Wire with solvent-based enamel in wound
components
N/A
2.10.5.13
Electric strength test

Routine test
N/A
Additional insulation in wound components
N/A
Working voltage .................................................... :
N/A
- Basic insulation not under stress ........................ :
N/A
- Supplementary, reinforced insulation .................. :
N/A
2.10.6
Construction of printed boards
N/A
2.10.6.1
Uncoated printed boards
N/A
2.10.6.2
Coated printed boards
N/A
2.10.6.3
Insulation between conductors on the same inner
surface of a printed board
N/A
2.10.6.4
Insulation between conductors on different layers of
a printed board
N/A
Distance through insulation
N/A
Number of insulation layers (pcs) ........................... :
N/A
2.10.7
Component external terminations
N/A
2.10.8
Tests on coated printed boards and coated
components
N/A
2.10.8.1
Sample preparation and preliminary inspection
N/A
2.10.5.14
TRF No. IEC60950_1C
Page 17 of 37
Report No.: 17036459 001
IEC 60950-1
Clause
Requirement + Test
Result - Remark
Verdict
2.10.8.2
Thermal conditioning
N/A
2.10.8.3
Electric strength test
N/A
2.10.8.4
Abrasion resistance test
N/A
2.10.9
Thermal cycling
N/A
2.10.10
Test for Pollution Degree 1 environment and
insulating compound
N/A
2.10.11
Tests for semiconductor devices and cemented
joints
N/A
2.10.12
Enclosed and sealed parts
N/A
3
WIRING, CONNECTIONS AND SUPPLY
P
3.1
General
P
3.1.1
Current rating and overcurrent protection
The internal wires have
suitable size to carry rated
current
P
3.1.2
Protection against mechanical damage
Wireways smooth and free
from sharp edges.
P
3.1.3
Securing of internal wiring
Internal wires are secured by
connectors so that a
loosening of the terminal
connection is unlikely
P
3.1.4
Insulation of conductors
The insulation of the individual
conductors suitable for the
application and the working
voltage. For the insulation
material see 3.1.1.
P
3.1.5
Beads and ceramic insulators
Not used.
3.1.6
Screws for electrical contact pressure
N/A
3.1.7
Insulating materials in electrical connections
N/A
3.1.8
Self-tapping and spaced thread screws
No self-tapping screws are
used.
N/A
3.1.9
Termination of conductors
All conductors are reliably
secured.
P
10 N pull test
Applied
P
3.1.10
3.2
N/A
Sleeving on wiring
N/A
Connection to a mains supply
N/A
No direct connection to mains. Requirements not applicable to the evaluated
product.
3.2.1
Means of connection
N/A
3.2.1.1
Connection to an a.c. mains supply
N/A
TRF No. IEC60950_1C
Page 18 of 37
Report No.: 17036459 001
IEC 60950-1
Clause
Requirement + Test
Result - Remark
Verdict
3.2.1.2
Connection to a d.c. mains supply
N/A
3.2.2
Multiple supply connections
N/A
3.2.3
Permanently connected equipment
N/A
Number of conductors, diameter of cable and
conduits (mm) ....................................................... :

3.2.4
Appliance inlets
N/A
3.2.5
Power supply cords
N/A
3.2.5.1
AC power supply cords
N/A
Type ...................................................................... :
2
Rated current (A), cross-sectional area (mm ),
AWG ..................................................................... :


3.2.5.2
DC power supply cords
N/A
3.2.6
Cord anchorages and strain relief
N/A
Mass of equipment (kg), pull (N) ......................... :

Longitudinal displacement (mm) ........................... :

3.2.7
Protection against mechanical damage
N/A
3.2.8
Cord guards
N/A
Diameter or minor dimension D (mm); test mass (g)
............................................................................... :

Radius of curvature of cord (mm) .......................... :

3.2.9
Supply wiring space
N/A
3.3
Wiring terminals for connection of external conductors
N/A
No direct connection to mains. Requirements not applicable to the evaluated
product.
3.3.1
Wiring terminals
N/A
3.3.2
Connection of non-detachable power supply cords
N/A
3.3.3
Screw terminals
N/A
3.3.4
Conductor sizes to be connected
N/A
Rated current (A), cord/cable type, cross-sectional
area (mm2) ............................................................. :
3.3.5
Wiring terminal sizes
Rated current (A), type, nominal thread diameter
(mm) ..................................................................... :

N/A

3.3.6
Wiring terminal design
N/A
3.3.7
Grouping of wiring terminals
N/A
3.3.8
Stranded wire
N/A
TRF No. IEC60950_1C
Page 19 of 37
Report No.: 17036459 001
IEC 60950-1
Clause
3.4
Requirement + Test
Result - Remark
Disconnection from the mains supply
Verdict
N/A
No direct connection to mains. Requirements not applicable to the evaluated
product.
3.4.1
General requirement
N/A
3.4.2
Disconnect devices
N/A
3.4.3
Permanently connected equipment
N/A
3.4.4
Parts which remain energized
N/A
3.4.5
Switches in flexible cords
N/A
3.4.6
Number of poles - single-phase and d.c. equipment
N/A
3.4.7
Number of poles - three-phase equipment
N/A
3.4.8
Switches as disconnect devices
N/A
3.4.9
Plugs as disconnect devices
N/A
3.4.10
Interconnected equipment
N/A
3.4.11
Multiple power sources
N/A
3.5
Interconnection of equipment
3.5.1
General requirements
This power supply is not
considered for connection to
TNV.
P
3.5.2
Types of interconnection circuits .......................... :
Interconnection circuits of
SELV through the connector.
No ELV interconnection
circuits.
P
3.5.3
ELV circuits as interconnection circuits
No ELV interconnection
3.5.4
Data ports for additional equipment
Unit powered by LPS.
4
PHYSICAL REQUIREMENTS
P
4.1
Stability
P
Angle of 10°
4.2
P
As the unit is less than 7kg.
N/A
P
N/A
Test force (N) ........................................................ :
N/A
Mechanical strength
N/A
Evaluated product supplied by SELV and all the circuits inside the enclosure are
SELV circuits or Limited Current Circuits
4.2.1
General
N/A
Rack-mounted equipment.
N/A
4.2.2
Steady force test, 10 N
N/A
4.2.3
Steady force test, 30 N
N/A
TRF No. IEC60950_1C
Page 20 of 37
Report No.: 17036459 001
IEC 60950-1
Clause
Requirement + Test
Result - Remark
Verdict
4.2.4
Steady force test, 250 N
N/A
4.2.5
Impact test
N/A
Fall test
N/A
Swing test
N/A
4.2.6
Drop test; height (mm) .......................................... :
N/A
4.2.7
Stress relief test
4.2.8
Cathode ray tubes
N/A
Picture tube separately certified ............................ :
N/A
4.2.9
High pressure lamps
N/A
4.2.10
Wall or ceiling mounted equipment; force (N) ....... :
N/A
4.3
Design and construction
4.3.1
Edges and corners
Edges and corners of the
enclosure are rounded.
4.3.2
Handles and manual controls; force (N) ............. :
No safety relevant handles or
manual controls.
N/A
4.3.3
Adjustable controls
No such controls.
N/A
4.3.4
Securing of parts
All parts secured properly.
Spring washer used for
securing screws.
4.3.5
Connection by plugs and sockets
Output connector does not
comply with IEC 60083 or IEC
60320.
N/A
4.3.6
Direct plug-in equipment
Not such equipment.
N/A
No CRT
N/A
P
P
P
Torque .................................................................. :

Compliance with the relevant mains plug standard
.............................................................................. :
N/A
4.3.7
Heating elements in earthed equipment
None.
N/A
4.3.8
Batteries
No batteries.
N/A
- Overcharging of a rechargeable battery
N/A
- Unintentional charging of a non-rechargeable
battery
N/A
- Reverse charging of a rechargeable battery
N/A
- Excessive discharging rate for any battery
N/A
4.3.9
Oil and grease
None.
N/A
4.3.10
Dust, powders, liquids and gases
Equipment in intended use
not considered to be exposed
to these.
N/A
4.3.11
Containers for liquids or gases
None
N/A
TRF No. IEC60950_1C
Page 21 of 37
Report No.: 17036459 001
IEC 60950-1
Clause
4.3.12
Requirement + Test
Result - Remark
Flammable liquids ................................................ :
None
N/A
Quantity of liquid (l) .............................................. :
N/A
Flash point (°C) .................................................... :
N/A
4.3.13
Radiation
4.3.13.1
General
See below
4.3.13.2
Ionizing radiation
No ionizing radiation.
4.3.13.3
Verdict
P
P
N/A
Measured radiation (pA/kg) .................................. :

Measured high-voltage (kV) ................................. :

Measured focus voltage (kV) ............................... :

CRT markings ...................................................... :

Effect of ultraviolet (UV) radiation on materials
No ultraviolet radiation
Part, property, retention after test, flammability
classification ......................................................... :
N/A
N/A
4.3.13.4
Human exposure to ultraviolet (UV) radiation ...... :
No ultraviolet radiation
4.3.13.5
Lasers (including laser diodes) and LEDs
See below.
4.3.13.5.1
Lasers (including laser diodes)
Not used.
N/A
P
N/A

Laser class ........................................................... :
4.3.13.5.2
Light emitting diodes (LEDs)
4.3.13.6
Other types ........................................................... :
N/A
4.4
Protection against hazardous moving parts
N/A
4.4.1
General
N/A
4.4.2
Protection in operator access areas .................... :
N/A
Household and home/office document/media
shredders
N/A
4.4.3
Protection in restricted access locations .............. :
N/A
4.4.4
Protection in service access areas
N/A
4.4.5
Protection against moving fan blades
N/A
4.4.5.1
General
N/A
Not considered to cause pain or injury. a)………….:
N/A
Is considered to cause pain, not injury. b) …………:
N/A
Considered to cause injury.
N/A
4.4.5.2
4.4.5.3
Indicating LED on secondary
is inherently exempted group
according to IEC 62471.
c) …………:
P
Protection for users
N/A
Use of symbol or warning ……………………………:
N/A
Protection for service persons
N/A
TRF No. IEC60950_1C
Page 22 of 37
Report No.: 17036459 001
IEC 60950-1
Clause
Requirement + Test
Result - Remark
Use of symbol or warning ……………………………:
Verdict
N/A
4.5
Thermal requirements
P
4.5.1
General
P
4.5.2
Temperature tests
According to the client’s
request, to simulate the worst
case end use of the final
equipment, the EUT is tested
in a sealed plastic bag.
P
Normal load condition per Annex L ...................... :
The equipment was
continuous working with
contrast and brightness set to
max.

4.5.3
Temperature limits for materials
(see appended table 4.5)
P
4.5.4
Touch temperature limits
(see appended table 4.5)
P
4.5.5
Resistance to abnormal heat ............................... :
4.6
Openings in enclosures
4.6.1
Top and side openings
N/A
P
(see appended table 4.6.1
and 4.6.2)

Dimensions (mm) ................................................. :
4.6.2
Bottoms of fire enclosures
P
(see appended table 4.6.1
and 4.6.2)
P

Construction of the bottomm, dimensions (mm) .. :
4.6.3
Doors or covers in fire enclosures
No doors or covers.
N/A
4.6.4
Openings in transportable equipment
Not transportable equipment.
N/A
4.6.4.1
Constructional design measures
N/A

Dimensions (mm) ................................................. :
4.6.4.2
Evaluation measures for larger openings
N/A
4.6.4.3
Use of metallized parts
N/A
4.6.5
Adhesives for constructional purposes
No adhesives for
constructional purposes.
Conditioning temperature (°C), time (weeks) ........ :
See above
4.7
Resistance to fire
4.7.1
Reducing the risk of ignition and spread of flame
Method 1, selection and application of components
wiring and materials
Method 2, application of all of simulated fault
condition tests
TRF No. IEC60950_1C
N/A

P
Use of materials with the
required flammability classes.
P
P
N/A
Page 23 of 37
Report No.: 17036459 001
IEC 60950-1
Clause
Requirement + Test
Result - Remark
Verdict
P
4.7.2
Conditions for a fire enclosure
The unit is powered by limited
power source from approved
external adapter and internal
parts/components mounted
on V-0 PCB.
4.7.2.1
Parts requiring a fire enclosure
See above.
N/A
4.7.2.2
Parts not requiring a fire enclosure
See above.
P
4.7.3
Materials
4.7.3.1
General
4.7.3.2
Materials for fire enclosures
4.7.3.3
Materials for components and other parts outside
fire enclosures
4.7.3.4
Materials for components and other parts inside fire
enclosures
4.7.3.5
Materials for air filter assemblies
No air filter.
N/A
4.7.3.6
Materials used in high-voltage components
No such high voltage
components in this meaning
N/A
5
ELECTRICAL REQUIREMENTS AND SIMULATED ABNORMAL CONDITIONS
5.1
Touch current and protective conductor current
Class III product, requirements not applicable to the evaluated product.
N/A
5.1.1
General
N/A
5.1.2
Configuration of equipment under test (EUT)
N/A
5.1.2.1
Single connection to an a.c. mains supply
N/A
5.1.2.2
Redundant multiple connections to an a.c. mains
supply
N/A
5.1.2.3
Simultaneous multiple connections to an a.c. mains
supply
N/A
5.1.3
Test circuit
N/A
5.1.4
Application of measuring instrument
N/A
5.1.5
Test procedure
N/A
5.1.6
Test measurements
N/A
P
PCB rated V-0
P
N/A
P
N/A
P
Supply voltage (V) ................................................ :

Measured touch current (mA) .............................. :

Max. allowed touch current (mA) ......................... :

Measured protective conductor current (mA) ....... :

Max. allowed protective conductor current (mA) ... :

5.1.7
Equipment with touch current exceeding 3,5 mA
N/A
5.1.7.1
General ................................................................. :
N/A
TRF No. IEC60950_1C
Page 24 of 37
Report No.: 17036459 001
IEC 60950-1
Clause
Requirement + Test
Result - Remark
Verdict
5.1.7.2
Simultaneous multiple connections to the supply
N/A
5.1.8
Touch currents to telecommunication networks and No TNV circuits.
cable distribution systems and from
telecommunication networks
N/A
5.1.8.1
Limitation of the touch current to a
telecommunication network or to a cable
distribution system
N/A
5.1.8.2
5.2
Supply voltage (V) ................................................ :

Measured touch current (mA) .............................. :

Max. allowed touch current (mA) ......................... :

Summation of touch currents from
telecommunication networks
N/A
a) EUT with earthed telecommunication ports ..... :
N/A
b) EUT whose telecommunication ports have no
reference to protective earth
N/A
Electric strength
N/A
Class III product, requirements not applicable to the evaluated product.
5.2.1
General
N/A
5.2.2
Test procedure
N/A
5.3
Abnormal operating and fault conditions
P
5.3.1
Protection against overload and abnormal operation see appended table 5.3
P
5.3.2
Motors
No motors.
N/A
5.3.3
Transformers
Considered in approved
external adapters.
N/A
5.3.4
Functional insulation .............................................. :
Method c used, see appended
table 5.3
5.3.5
Electromechanical components
No electromechanical
component.
5.3.6
Audio amplifiers in ITE ......................................... :
5.3.7
Simulation of faults
(see appended table 5.3.)
5.3.8
Unattended equipment
No such equipment.
5.3.9
Compliance criteria for abnormal operating and
fault conditions
5.3.9.1
During the tests
5.3.9.2
After the tests
TRF No. IEC60950_1C
P
N/A
N/A
P
N/A
P
No fire or molten metal
occurred and no deformation
of enclosure during the tests.
P
N/A
Page 25 of 37
Report No.: 17036459 001
IEC 60950-1
Clause
Requirement + Test
Result - Remark
Verdict
6
CONNECTION TO TELECOMMUNICATION NETWORKS
N/A
6.1
Protection of telecommunication network service persons, and users of other
equipment connected to the network, from hazards in the equipment
N/A
6.1.1
Protection from hazardous voltages
N/A
6.1.2
Separation of the telecommunication network from earth
N/A
6.1.2.1
Requirements
N/A
Supply voltage (V) ................................................ :

Current in the test circuit (mA) ........................... :

6.1.2.2
Exclusions ............................................................ :
6.2
Protection of equipment users from overvoltages on telecommunication
networks
N/A
6.2.1
Separation requirements
N/A
6.2.2
Electric strength test procedure
N/A
6.2.2.1
Impulse test
N/A
6.2.2.2
Steady-state test
N/A
6.2.2.3
Compliance criteria
N/A
6.3
Protection of the telecommunication wiring system from overheating
N/A
Max. output current (A) ........................................ :

Current limiting method ........................................ :

7
CONNECTION TO CABLE DISTRIBUTION SYSTEMS
N/A
7.1
General
N/A
7.2
Protection of cable distribution system service
persons, and users of other equipment connected
to the system, from hazardous voltages in the
equipment
N/A
7.3
Protection of equipment users from overvoltages
on the cable distribution system
N/A
7.4
Insulation between primary circuits and cable
distribution systems
N/A
7.4.1
General
N/A
7.4.2
Voltage surge test
N/A
7.4.3
Impulse test
N/A
A
ANNEX A, TESTS FOR RESISTANCE TO HEAT AND FIRE
N/A
TRF No. IEC60950_1C
Page 26 of 37
Report No.: 17036459 001
IEC 60950-1
Clause
Requirement + Test
Result - Remark
Verdict
A.1
Flammability test for fire enclosures of movable
equipment having a total mass exceeding 18 kg,
and of stationary equipment (see 4.7.3.2)
A.1.1
Samples ................................................................ :

Wall thickness (mm) ............................................. :

A.1.2
Conditioning of samples; temperature (°C) .......... :
N/A
A.1.3
Mounting of samples ............................................ :
N/A
A.1.4
Test flame (see IEC 60695-11-3)
N/A
Flame A, B, C or D ............................................... :
N/A

A.1.5
Test procedure
N/A
A.1.6
Compliance criteria
N/A
Sample 1 burning time (s) ..................................... :

Sample 2 burning time (s) ..................................... :

Sample 3 burning time (s) ..................................... :

A.2
Flammability test for fire enclosures of movable equipment having a total mass not
exceeding 18 kg, and for material and components located inside fire enclosures
(see 4.7.3.2 and 4.7.3.4)
A.2.1
Samples, material ................................................. :

Wall thickness (mm) ............................................. :

A.2.2
Conditioning of samples; temperature (°C) .. ........ :
N/A
A.2.3
Mounting of samples ............................................ :
N/A
A.2.4
Test flame (see IEC 60695-11-4)
N/A
Flame A, B or C .................................................... :
N/A

A.2.5
Test procedure
N/A
A.2.6
Compliance criteria
N/A
A.2.7
Sample 1 burning time (s) ..................................... :

Sample 2 burning time (s) ..................................... :

Sample 3 burning time (s) ..................................... :

Alternative test acc. to IEC 60695-11-5, cl. 5 and 9
N/A
Sample 1 burning time (s) ..................................... :

Sample 2 burning time (s) ..................................... :

Sample 3 burning time (s) ..................................... :

A.3
Hot flaming oil test (see 4.6.2)
N/A
A.3.1
Mounting of samples
N/A
A.3.2
Test procedure
N/A
A.3.3
Compliance criterion
N/A
TRF No. IEC60950_1C
Page 27 of 37
Report No.: 17036459 001
IEC 60950-1
Clause
Requirement + Test
Result - Remark
Verdict
B
ANNEX B, MOTOR TESTS UNDER ABNORMAL CONDITIONS (see 4.7.2.2 and
5.3.2)
N/A
B.1
General requirements
N/A
Position ................................................................ :

ManuFacturer ....................................................... :

Type ..................................................................... :

Rated values ....................................................... :

B.2
Test conditions
N/A
B.3
Maximum temperatures
N/A
B.4
Running overload test
N/A
B.5
Locked-rotor overload test
N/A
Test duration (days) ............................................. :

Electric strength test: test voltage (V) .................. :

B.6
Running overload test for d.c. motors in secondary
circuits
N/A
B.6.1
General
N/A
B.6.2
Test procedure
N/A
B.6.3
Alternative test procedure
N/A
B.6.4
Electric strength test; test voltage (V) .................. :
N/A
B.7
Locked-rotor overload test for d.c. motors in
secondary circuits
N/A
B.7.1
General
N/A
B.7.2
Test procedure
N/A
B.7.3
Alternative test procedure
N/A
B.7.4
Electric strength test; test voltage (V) ................. :
N/A
B.8
Test for motors with capacitors
N/A
B.9
Test for three-phase motors
N/A
B.10
Test for series motors
N/A
Operating voltage (V) ........................................... :
C
ANNEX C, TRANSFORMERS (see 1.5.4 and 5.3.3)

N/A
Considered in approved external adapter.
Position ................................................................ :

ManuFacturer ....................................................... :

Type ..................................................................... :

Rated values ....................................................... :

Method of protection ............................................. :

TRF No. IEC60950_1C
Page 28 of 37
Report No.: 17036459 001
IEC 60950-1
Clause
Requirement + Test
Result - Remark
Verdict
C.1
Overload test
N/A
C.2
Insulation
N/A
Protection from displacement of windings ............ :
N/A
D
ANNEX D, MEASURING INSTRUMENTS FOR TOUCH-CURRENT TESTS
(see 5.1.4)
N/A
D.1
Measuring instrument
N/A
D.2
Alternative measuring instrument
N/A
E
ANNEX E, TEMPERATURE RISE OF A WINDING (see 1.4.13)
N/A
F
ANNEX F, MEASUREMENT OF CLEARANCES AND CREEPAGE DISTANCES
(see 2.10 and Annex G)
N/A
G
ANNEX G, ALTERNATIVE METHOD FOR DETERMINING MINIMUM
CLEARANCES
N/A
G.1
Clearances
N/A
G.1.1
General
N/A
G.1.2
Summary of the procedure for determining
minimum clearances
N/A
G.2
Determination of mains transient voltage (V)
N/A
G.2.1
AC mains supply .................................................. :
N/A
G.2.2
Earthed d.c. mains supplies ................................. :
N/A
G.2.3
Unearthed d.c. mains supplies ............................. :
N/A
G.2.4
Battery operation .................................................. :
N/A
G.3
Determination of telecommunication network
transient voltage (V) ............................................. :
N/A
G.4
Determination of required withstand voltage (V)
N/A
G.4.1
Mains transients and internal repetitive peaks ..... :
N/A
G.4.2
Transients from telecommunication networks ..... :
N/A
G.4.3
Combination of transients
N/A
G.4.4
Transients from cable distribution systems
N/A
G.5
Measurement of transient voltages (V)
N/A
a) Transients from a mains supply
N/A
For an a.c. mains supply
N/A
For a d.c. mains supply
N/A
b) Transients from a telecommunication network
N/A
Determination of minimum clearances ................ :
N/A
G.6
TRF No. IEC60950_1C
Page 29 of 37
Report No.: 17036459 001
IEC 60950-1
Clause
Requirement + Test
Result - Remark
Verdict
H
ANNEX H, IONIZING RADIATION (see 4.3.13)
N/A
J
ANNEX J, TABLE OF ELECTROCHEMICAL POTENTIALS (see 2.6.5.6)
N/A

Metal(s) used ....................................................... :
K
ANNEX K, THERMAL CONTROLS (see 1.5.3 and 5.3.8)
N/A
K.1
Making and breaking capacity
N/A
K.2
Thermostat reliability; operating voltage (V) ......... :
N/A
K.3
Thermostat endurance test; operating voltage (V)
.............................................................................. :
N/A
K.4
Temperature limiter endurance; operating voltage
(V) ........................................................................ :
N/A
K.5
Thermal cut-out reliability
N/A
K.6
Stability of operation
N/A
L
ANNEX L, NORMAL LOAD CONDITIONS FOR SOME TYPES OF ELECTRICAL
BUSINESS EQUIPMENT (see 1.2.2.1 and 4.5.2)
L.1
Typewriters
N/A
L.2
Adding machines and cash registers
N/A
L.3
Erasers
N/A
L.4
Pencil sharpeners
N/A
L.5
Duplicators and copy machines
N/A
L.6
Motor-operated files
N/A
L.7
Other business equipment
M
ANNEX M, CRITERIA FOR TELEPHONE RINGING SIGNALS (see 2.3.1)
N/A
M.1
Introduction
N/A
M.2
Method A
N/A
M.3
Method B
N/A
M.3.1
Ringing signal
N/A
M.3.1.1
Frequency (Hz) ..................................................... :

M.3.1.2
Voltage (V) ........................................................... :

M.3.1.3
Cadence; time (s), voltage (V) ............................. :

M.3.1.4
Single fault current (mA) ...................................... :

M.3.2
Tripping device and monitoring voltage ............... :
N/A
TRF No. IEC60950_1C
See 1.6.2.
P
P
Page 30 of 37
Report No.: 17036459 001
IEC 60950-1
Clause
Requirement + Test
Result - Remark
Verdict
M.3.2.1
Conditions for use of a tripping device or a
monitoring voltage
N/A
M.3.2.2
Tripping device
N/A
M.3.2.3
Monitoring voltage (V) .......................................... :
N/A
N
ANNEX N, IMPULSE TEST GENERATORS (see 1.5.7.2, 1.5.7.3, 2.10.3.9, 6.2.2.1,
7.3.2, 7.4.3 and Clause G.5)
N/A
N.1
ITU-T impulse test generators
N/A
N.2
IEC 60065 impulse test generator
N/A
P
ANNEX P, NORMATIVE REFERENCES
Q
ANNEX Q, Voltage dependent resistors (VDRs) (see 1.5.9.1)

.
N/A
a) Preferred climatic categories ........................... :
N/A
b) Maximum continuous voltage .......................... :
N/A
c) Pulse current .................................................... :
N/A
R
ANNEX R, EXAMPLES OF REQUIREMENTS FOR QUALITY CONTROL
PROGRAMMES
N/A
R.1
Minimum separation distances for unpopulated
coated printed boards (see 2.10.6.2)
N/A
R.2
Reduced clearances (see 2.10.3)
N/A
S
ANNEX S, PROCEDURE FOR IMPULSE TESTING (see 6.2.2.3)
N/A
S.1
Test equipment
N/A
S.2
Test procedure
N/A
S.3
Examples of waveforms during impulse testing
N/A
T
ANNEX T, GUIDANCE ON PROTECTION AGAINST INGRESS OF WATER
(see 1.1.2)
N/A

U
ANNEX U, INSULATED WINDING WIRES FOR USE WITHOUT INTERLEAVED
INSULATION (see 2.10.5.4)
N/A

V
ANNEX V, AC POWER DISTRIBUTION SYSTEMS (see 1.6.1)
N/A
V.1
Introduction
N/A
TRF No. IEC60950_1C
Page 31 of 37
Report No.: 17036459 001
IEC 60950-1
Clause
Requirement + Test
Result - Remark
Verdict
V.2
TN power distribution systems
N/A
W
ANNEX W, SUMMATION OF TOUCH CURRENTS
N/A
W.1
Touch current from electronic circuits
N/A
W.1.1
Floating circuits
N/A
W.1.2
Earthed circuits
N/A
W.2
Interconnection of several equipments
N/A
W.2.1
Isolation
N/A
W.2.2
Common return, isolated from earth
N/A
W.2.3
Common return, connected to protective earth
N/A
X
ANNEX X, MAXIMUM HEATING EFFECT IN TRANSFORMER TESTS
N/A
X.1
Determination of maximum input current
N/A
X.2
Overload test procedure
N/A
Y
ANNEX Y, ULTRAVIOLET LIGHT CONDITIONING TEST (see 4.3.13.3)
N/A
Y.1
Test apparatus ..................................................... :
N/A
Y.2
Mounting of test samples ..................................... :
N/A
Y.3
Carbon-arc light-exposure apparatus .................. :
N/A
Y.4
Xenon-arc light exposure apparatus .................... :
N/A
Z
ANNEX Z, OVERVOLTAGE CATEGORIES (see 2.10.3.2 and Clause G.2)
N/A
AA
ANNEX AA, MANDREL TEST (see 2.10.5.8)
N/A
BB
ANNEX BB, CHANGES IN THE SECOND EDITION
CC
ANNEX CC, Evaluation of integrated circuit (IC) current limiters
N/A
CC.1
General
N/A
CC.2
Test program 1……………………………………….:
N/A
CC.3
Test program 2……………………………………….:
N/A
DD
ANNEX DD, Requirements for the mounting means of rack-mounted
equipment
N/A
DD.1
General
N/A
DD.2
Mechanical strength test, variable N………………..:
N/A
TRF No. IEC60950_1C

Page 32 of 37
Report No.: 17036459 001
IEC 60950-1
Clause
Requirement + Test
Result - Remark
Verdict
DD.3
Mechanical strength test, 250N, including end
stops……………………………………………………:
N/A
DD.4
Compliance……………………………………………:
N/A
EE
ANNEX EE, Household and home/office document/media shredders
N/A
EE.1
General
N/A
EE.2
Markings and instructions
N/A
Use of markings or symbols…………………………:
N/A
Information of user instructions, maintenance
and/or servicing instructions…………………………:
N/A
EE.3
Inadvertent reactivation test…………………………:
N/A
EE.4
Disconnection of power to hazardous moving parts:
N/A
Use of markings or symbols…………………………:
N/A
Protection against hazardous moving parts
N/A
Test with test finger (Figure 2A) ……………………:
N/A
Test with wedge probe (Figure EE1 and EE2) ……:
N/A
EE.5
TRF No. IEC60950_1C
Page 33 of 37
1.5.1
Report No.: 17036459 001
TABLE: list of critical components
P
Object/part no.
Manufacturer/
trademark
Type/model
Technical data
Standard
Mark(s) of
conformity 1.
LCD Panel with
CCFL backlight
Samsung
Electronics Co.,
Ltd.
LTM170ET01
17 inch TFT, CCFL
backlight.
--
--
PCB
Interchangeable
Interchangeable
V-0, 130°C
--
UL
AC Adapter
Shenzhen
Meikai
Electronics
Stock Co., Ltd.
PDN-48-48A
I/P: 100-240Vac,
50/60Hz, 1.0A,
DP1EEL19011aH
130°C
Transformer (T1 Shenzhen Dataon inverter
Power
board)
Electronics Co.,
Ltd.
IEC 60950Nemko
1:2005+A1:20 Hong Kong
09*,
Ltd. CB, GS
Class I
(CB report
EN 60950-1:
O/P: 12.0Vdc, 4.16A
no. 227063,
2006+A11:
cert. No.
2009+A1:
Max. ambient
NO72373)
2010+A12:
temperature is
(GS cert.
2011*
40°°C.
No. GS1212227063-000)
---
Test with
appliance
Test with
appliance
Inverter
Shenzhen Data- DATA-02Power
15042AH
Electronics Co.,
Ltd.
Input: 12Vd.c
--Output: 916V in CN3
connector, 898V in
CN2 connector
Internal wires
Interchangeable
Interchangeable
300V, 80°C, min 26
AWG
UL 758
UL
Enclosure
--
--
Metallic, minimum
1.0mm thickness
--
--
Supplementary information: * Standard version should be updated when necessary before applying for
national approval.
1)
An asterisk indicates a mark that assures the agreed level of surveillance.
TRF No. IEC60950_1C
Page 34 of 37
1.6.2
TABLE: Electrical data (in normal conditions)
U (V)
I (A)
Irated (A)
P (W)
Report No.: 17036459 001
P
Fuse #
Ifuse (A)
Condition/status
--
--
Normal load condition
--
--
Normal load condition
Tested with AC adapter (PDN-48-48A), VGA mode
12Vdc
1.34
4.16
16.2
Tested with AC adapter (PDN-48-48A), DVI mode
12Vdc
1.33
4.16
16.1
Note(s):
- Normal load: Brightness: 100%, Contrast: 100%, resolution 1280x1024, white screen.
2.4.2
TABLE: limited current circuit measurement
Location
P
Voltage
(V)
Current
(mA)
Freq.
(kHz)
Limit
(mA)
Comments
CN3, between pin 1 and pin 2
16.4
8.2
50.5
35.35
--
CN3, between pin 1 and GND
16.4
8.2
50.5
35.35
--
CN2, between pin 1 and pin 2
15.1
7.55
50.5
35.35
--
CN2, between pin 1 and GND
18.3
9.15
50.5
35.35
--
CN2, between pin 2 and GND
4.8
2.4
50.5
35.35
--
CN3, between pin1 and pin 2
0
*
0
*
Unit shut down
CN3, between pin1 and GND
0
*
0
*
Unit shut down
CN2, between pin1 and pin 2
0
*
0
*
Unit shut down
CN2, between pin1 and GND
0
*
0
*
Unit shut down
CN2, between pin2 and GND
0
*
0
*
Unit shut down
CN3, between pin1 and pin 2
0
*
0
*
Unit shut down
CN3, between pin1 and GND
0
*
0
*
Unit shut down
CN2, between pin1 and pin 2
0
*
0
*
Unit shut down
CN2, between pin1 and GND
0
*
0
*
Unit shut down
CN2, between pin2 and GND
0
*
0
*
Unit shut down
CN3, between pin1 and pin 2
0
*
0
*
Unit shut down
CN3, between pin1 and GND
0
*
0
*
Unit shut down
CN2, between pin1 and pin 2
0
*
0
*
Unit shut down
Normal condition
Single fault condition:C12 short
Single fault condition: D1 pin 2 - GND short
Single fault condition: Q1 pin 1 – pin 2 short
TRF No. IEC60950_1C
Page 35 of 37
Report No.: 17036459 001
CN2, between pin1 and GND
0
*
0
*
Unit shut down
CN2, between pin2 and GND
0
*
0
*
Unit shut down
CN3, between pin1 and pin 2
0
*
0
*
Unit shut down
CN3, between pin1 and GND
0
*
0
*
Unit shut down
CN2, between pin1 and pin 2
0
*
0
*
Unit shut down
CN2, between pin1 and GND
0
*
0
*
Unit shut down
CN2, between pin2 and GND
0
*
0
*
Unit shut down
CN3, between pin1 and pin 2
0
*
0
*
Unit shut down
CN3, between pin1 and pin 2
0
*
0
*
Unit shut down
CN3, between pin1 and GND
0
*
0
*
Unit shut down
CN2, between pin1 and pin 2
0
*
0
*
Unit shut down
CN2, between pin1 and GND
0
*
0
*
Unit shut down
CN2, between pin2 and GND
0
*
0
*
Unit shut down
CN3, between pin1 and pin 2
0
*
0
*
Unit shut down
CN3, between pin1 and GND
0
*
0
*
Unit shut down
CN2, between pin1 and pin 2
0
*
0
*
Unit shut down
CN2, between pin1 and GND
0
*
0
*
Unit shut down
CN2, between pin2 and GND
0
*
0
*
Unit shut down
Single fault condition: Q1 pin 1 – pin 8 short
Single fault condition: Q1 pin 2 – pin 8 short
Single fault condition: U1 pin 7 – pin 13 short
Note: “*” indicates the unit shut down immediately.
2.10.2
P
Table: working voltage measurement
Location
RMS voltage (V)
Peak voltage (V) Comments
Working voltage of the inverter output
CN3, between pin1 and pin 2
--
916 V peak
For reference
CN2, between pin1 and pin 2
--
898 V peak
For reference
supplementary information:
Fault condition test is considered, see table 5.3.
Although the working voltage of inverter output is exceeds SELV, however it has been classified as bare
parts of limited current circuits due to it has been passed the test of clause 2.4 limited current circuit, so no
electric shock hazard exists and no test requirement of clause 2.10.3&2.10.4 is required.
TRF No. IEC60950_1C
Page 36 of 37
4.5.1
Report No.: 17036459 001
TABLE: maximum temperatures
P
Test voltage (V) ...............................
12Vdc

-Tamb1 (°C) ................................

-Tamb2 (°C) ................................

Monitored point:
12Vdc
allowed Tmax (°C)
DC inlet
40.7
--
PCB of control plate
46.7
130-40+25.9 = 115.9
PCB of USB
40.1
130-40+25.9 = 115.9
Internal wires
42.6
80-40+25.9 = 65.9
Annular line choke (T2) (on main board)
58.0
130-40+25.9-10 = 105.9
Electrolytic capacitor (E5) (on main board)
57.7
105-40+25.9 = 90.9
PCB near chip U3 (on main board)
58.0
130-40+25.9 = 115.9
Inverter transformer winding (T1) (on inverter board)
72.5
130-40+25.9-10 = 105.9
Inverter transformer core (T1) (on inverter board)
63.4
130-40+25.9-10 = 105.9
Electrolytic capacitor (C12) (on inverter board)
58.1
85-40+25.9 = 70.9
PCB near T1 (on inverter board)
60.4
130-40+25.9 = 115.9
Enclosure inside
41.2
70-40+25.9 = 55.9
Enclosure outside
41.2
70-40+25.9 = 55.9
Surface of LCD panel
35.1
80-40+25.9 = 65.9
Ambient
25.9
--
Monitor
Note:
-
As the EUT is a open frame LCD monitor with touch screen, in order to simulate the most unfavourable
condition in final equipment, according to the client’s request, the test is performed in a sealed plastic
bag. No need to perform the block opening test in clause 5.3.
-
Max. ambient temperature is 40°C.
TRF No. IEC60950_1C
Page 37 of 37
5.3
Report No.: 17036459 001
TABLE: Fault condition tests
P
Ambient temperature (°C) ................................
25°C, if no other specified

Power source for EUT: ManuFacturer,
(see table 1.5.1)
model/type, output rating ................................

Component
No.
Fault
Supply
voltage
(V)
Test time
Fuse #
Fuse
current
(A)
Observation
Ventilation openings
blocke 12Vd.c.
d
2hrs
--
--
Unit normal operation.
Measured maximum
temperature see Table 4.5.1.
DC inlet
revers
ed
12Vd.c.
10min
--
--
Unit shut down immediately,
recoverable after the fault
removed, no hazard.
Electrolytic capacitor
(E5) (on main board)
s-c
12Vd.c.
10min
--
--
Unit shut down immediately,
recoverable after the fault
removed, no hazard.
Electrolytic capacitor
(E1) (on main board)
s-c
12Vd.c.
10min
--
--
Unit shut down immediately,
recoverable after the fault
removed, no hazard.
Chip U4 (on main
board), pin 1 and pin 2
s-c
12Vd.c.
10min
--
--
Unit shut down immediately,
recoverable after the fault
removed, no hazard.
C12 (on inverter board) s-c
12Vd.c.
10min
--
--
Unit shut down immediately,
recoverable after the fault
removed, no hazard.
D1 (on inverter board),
pin 2 and GND
s-c
12Vd.c.
10min
--
--
Unit shut down immediately,
recoverable after the fault
removed, no hazard.
Q1 (on inverter board),
pin 1 and pin 8
s-c
12Vd.c.
10min
--
--
Unit shut down immediately,
recoverable after the fault
removed, no hazard.
Q1 (on inverter board),
pin 2 and pin 8
s-c
12Vd.c.
10min
--
--
Unit shut down immediately,
recoverable after the fault
removed, no hazard.
Q1 (on inverter board),
pin 1 and pin 2
s-c
12Vd.c.
10min
--
--
Unit shut down immediately,
recoverable after the fault
removed, no hazard.
U1 (on inverter board),
pin 7 and pin 13
s-c
12Vd.c.
10min
--
--
Unit shut down immediately,
recoverable after the fault
removed, no hazard.
Supplementary information: s-c = short-circuited
TRF No. IEC60950_1C
Page 1 of 46
Report No.:17036459 001
IEC60950_1C – ATTACHMENT 1
Clause
Requirement + Test
Result - Remark
Verdict
ATTACHMENT TO TEST REPORT IEC 60950-1
EUROPEAN GROUP DIFFERENCES AND NATIONAL DIFFERENCES
Information technology equipment – Safety –
Part 1: General requirements
Differences according to................ :
EN 60950-1:2006/A11:2009/A1:2010/A12:2011
Attachment Form No. ..................... :
EU_GD_IEC60950_1C_II
Attachment Originator ................... :
SGS Fimko Ltd
Master Attachment ......................... :
Date 2011-08
Copyright © 2011 IEC System for Conformity Testing and Certification of Electrical Equipment
(IECEE), Geneva, Switzerland. All rights reserved.
EN 60950-1:2006/A11:2009/A1:2010/A12:2011 – CENELEC COMMON MODIFICATIONS
IEC 60950-1, GROUP DIFFERENCES (CENELEC common modifications EN)
Contents
Add the following annexes:
Annex ZA (normative)
Annex ZB (normative)
P
Normative references to international
publications with their corresponding European
publications
Special national conditions
General
Delete all the “country” notes in the reference document (IEC 60950-1:2005)
according to the following list:
1.4.8 Note 2
1.5.1
Note 2 & 3 1.5.7.1
Note
1.5.8 Note 2
1.5.9.4
Note
1.7.2.1
Note 4, 5 & 6
2.2.3 Note
2.2.4
Note
2.3.2
Note
2.3.2.1 Note 2
2.3.4
Note 2
2.6.3.3
Note 2 & 3
2.7.1 Note
2.10.3.2
Note 2
2.10.5.13
Note 3
3.2.1.1 Note
3.2.4
Note 3.
2.5.1
Note 2
4.3.6 Note 1 & 2 4.7
Note 4
4.7.2.2
Note
4.7.3.1Note 2
5.1.7.1
Note 3 & 4 5.3.7
Note 1
6
Note 2 & 5 6.1.2.1
Note 2
6.1.2.2
Note
6.2.2 Note
6.2.2.1
Note 2
6.2.2.2
Note
7.1
Note 3
7.2
Note
7.3
Note 1 & 2
G.2.1 Note 2
Annex H
Note 2
P
General
Delete all the “country” notes in the reference document (IEC 609501:2005/A1:2010) according to the following list:
1.5.7.1
Note
6.1.2.1
Note 2
6.2.2.1
Note 2
EE.3
Note
P
(A1:2010)
Page 2 of 46
Report No.:17036459 001
IEC60950_1C – ATTACHMENT 1
Clause
Requirement + Test
Result - Remark
1.3.Z1
Add the following subclause:
Added.
1.3.Z1 Exposure to excessive sound pressure
The apparatus shall be so designed and
constructed as to present no danger when used
for its intended purpose, either in normal
operating conditions or under fault conditions,
particularly providing protection against exposure
to excessive sound pressures from headphones
or earphones.
Verdict
N/A
NOTE Z1 A new method of measurement is described
in EN 50332-1, Sound system equipment:
Headphones and earphones associated with portable
audio equipment - Maximum sound pressure level
measurement methodology and limit considerations Part 1: General method for “one package equipment”,
and in EN 50332-2, Sound system equipment:
Headphones and earphones associated with portable
audio equipment - Maximum sound pressure level
measurement methodology and limit considerations Part 2: Guidelines to associate sets with headphones
coming from different manufacturers.
(A12:2011)
In EN 60950-1:2006/A12:2011
Delete the addition of 1.3.Z1 / EN 60950-1:2006
Delete the definition 1.2.3.Z1 / EN 60950-1:2006
/A1:2010
Deleted.
N/A
1.5.1
Add the following NOTE:
Added.
P
Added.
N/A
NOTE Z1 The use of certain substances in electrical
and electronic equipment is restricted within the EU:
see Directive 2002/95/EC
1.7.2.1
(A1:2010)
1.7.2.1
(A12.2011)
In addition, for a PORTABLE SOUND SYSTEM,
the instructions shall include a warning that
excessive sound pressure from earphones and
headphones can cause hearing loss.
In EN 60950-1:2006/A12:2011
Delete NOTE Z1 and the addition for Portable
Sound System.
Add the following clause and annex to the existing
standard and amendments.
N/A
Zx Protection against excessive sound pressure from personal music
players
N/A
Page 3 of 46
Report No.:17036459 001
IEC60950_1C – ATTACHMENT 1
Clause
Requirement + Test
Result - Remark
Zx.1 General
This sub-clause specifies requirements for
protection against excessive sound pressure
from personal music players that are closely
coupled to the ear. It also specifies requirements
for earphones and headphones intended for use
with personal music players.
Not personal music player
A personal music player is a portable
equipment for personal use, that:
is designed to allow the user to listen to
recorded or broadcast sound or video; and
primarily uses headphones or earphones that
can be worn in or on or around the ears; and
allows the user to walk around while in use.
NOTE 1 Examples are hand-held or body-worn portable CD
players, MP3 audio players, mobile phones with MP3 type
features, PDA’s or similar equipment.
A personal music player and earphones or
headphones intended to be used with personal
music players shall comply with the requirements
of this sub-clause.
The requirements in this sub-clause are valid for
music or video mode only.
The requirements do not apply:
while the personal music player is connected to
an external amplifier; or
while the headphones or earphones are not
used.
NOTE 2 An external amplifier is an amplifier which is not part
of the personal music player or the listening device, but which
is intended to play the music as a standalone music player.
The requirements do not apply to:
hearing aid equipment and professional
equipment;
NOTE 3 Professional equipment is equipment sold through
special sales channels. All products sold through normal
electronics stores are considered not to be professional
equipment.
Verdict
N/A
Page 4 of 46
Report No.:17036459 001
IEC60950_1C – ATTACHMENT 1
Clause
Requirement + Test
Result - Remark
Verdict
analogue personal music players (personal
music players without any kind of digital
processing of the sound signal) that are
brought
to the market before the end of
2015.
NOTE 4 This exemption has been allowed because this
technology is falling out of use and it is expected that within a
few years it will no longer exist. This exemption will not be
extended to other technologies.
For equipment which is clearly designed or
intended for use by young children, the limits of
EN 71-1 apply.
Zx.2 Equipment requirements
No safety provision is required for equipment that
complies with the following:
equipment provided as a package (personal
music player with its listening device), where
the acoustic output LAeq,T is ≤ 85 dBA measured
while playing the fixed “programme simulation
noise” as described in EN 50332-1; and
a personal music player provided with an
analogue electrical output socket for a listening
device, where the electrical output is ≤ 27 mV
measured as described in EN 50332-2, while
playing the fixed “programme simulation noise”
as described in EN 50332-1.
NOTE 1 Wherever the term acoustic output is used in this
clause, the 30 s A-weighted equivalent sound pressure level
LAeq,T is meant. See also Zx.5 and Annex Zx.
All other equipment shall:
a) protect the user from unintentional acoustic
outputs exceeding those mentioned above; and
b) have a standard acoustic output level not
exceeding those mentioned above, and
automatically return to an output level not
exceeding those mentioned above when the
power is switched off; and

N/A
Page 5 of 46
Report No.:17036459 001
IEC60950_1C – ATTACHMENT 1
Clause
Requirement + Test
c) provide a means to actively inform the user of
the increased sound pressure when the
equipment is operated with an acoustic output
exceeding those mentioned above. Any means
used shall be acknowledged by the user
before activating a mode of operation which
allows for
an acoustic output exceeding those
mentioned above. The acknowledgement does
not need to be repeated more than once every
20 h of
cumulative listening time; and
NOTE 2 Examples of means include visual or audible signals.
Action from the user is always required.
NOTE 3 The 20 h listening time is the accumulative listening
time, independent how often and how long the personal music
player has been switched off.
d) have a warning as specified in Zx.3; and
e) not exceed the following:
1) equipment provided as a package (player
with Its listening device), the acoustic output
shall be ≤ 100 dBA measured while playing the
fixed “programme simulation noise” described
in EN 50332-1; and
2) a personal music player provided with an
analogue electrical output socket for a listening
device, the electrical output shall be ≤ 150 mV
measured as described in EN 50332-2, while
playing the fixed “programme simulation noise”
described in EN 50332-1.
For music where the average sound pressure
(long term LAeq,T) measured over the duration of
the song is lower than the average produced by
the programme simulation noise, the warning
does not need to be given as long as the average
sound pressure of the song is below the basic
limit of 85 dBA. In this case T becomes the
duration of the song.
NOTE 4 Classical music typically has an average sound
pressure (long term LAeq,T) which is much lower than the
average programme simulation noise. Therefore, if the player
is capable to analyse the song and compare it with the
programme simulation noise, the warning does not need to be
given as long as the average sound pressure of the song is
below the basic limit of 85 dBA.
For example, if the player is set with the programme
simulation noise to 85 dBA, but the average music level of the
song is only 65 dBA, there is no need to give a warning or ask
an acknowledgement as long as the average sound level of
the song is not above the basic limit of 85 dBA.
Result - Remark
Verdict
N/A
Page 6 of 46
Report No.:17036459 001
IEC60950_1C – ATTACHMENT 1
Clause
Requirement + Test
Result - Remark
Zx.3 Warning
The warning shall be placed on the equipment, or
on the packaging, or in the instruction manual
and shall consist of the following:
Verdict
N/A
the symbol of Figure 1 with a minimum height
of
5 mm; and
the following wording, or similar:
“To prevent possible hearing damage, do not
listen at high volume levels for long periods.”
Figure 1 – Warning label (IEC 60417-6044)
Alternatively, the entire warning may be given
through the equipment display during use, when
the user is asked to acknowledge activation of
the higher level.
Zx.4 Requirements for listening devices (headphones and earphones)
N/A
Zx.4.1 Wired listening devices with analogue
input
With 94 dBA sound pressure output LAeq,T, the
input voltage of the fixed “programme simulation
noise” described in EN 50332-2 shall be ≥ 75
mV.
N/A
This requirement is applicable in any mode
where the headphones can operate (active or
passive), including any available setting (for
example built-in volume level control).
NOTE The values of 94 dBA – 75 mV correspond with 85dBA
– 27 mV and 100 dBA – 150 mV.
Page 7 of 46
Report No.:17036459 001
IEC60950_1C – ATTACHMENT 1
Clause
Requirement + Test
Zx.4.2 Wired listening devices with digital
input
Result - Remark
Verdict
N/A
With any playing device playing the fixed
“programme simulation noise” described in EN
50332-1 (and respecting the digital interface
standards, where a digital interface standard
exists that specifies the equivalent acoustic
level), the acoustic output LAeq,T of the listening
device shall be ≤ 100 dBA.
This requirement is applicable in any mode
where the headphones can operate, including
any available setting (for example built-in volume
level control, additional sound feature like
equalization, etc.).
NOTE An example of a wired listening device with digital input
is a USB headphone.
Zx.4.3 Wireless listening devices
In wireless mode:
N/A
with any playing and transmitting device playing
the fixed programme simulation noise
described
in EN 50332-1; and
respecting the wireless transmission standards,
where an air interface standard exists that
specifies the equivalent acoustic level; and
with volume and sound settings in the listening
device (for example built-in volume level
control,
additional sound feature like
equalization, etc.) set to the combination of
positions that
maximize the measured
acoustic output for the
abovementioned
programme simulation noise,
the acoustic
output LAeq,T of the listening device
shall be ≤
100 dBA.
NOTE An example of a wireless listening device is a
Bluetooth headphone.
Zx.5 Measurement methods
Measurements shall be made in accordance with
EN 50332-1 or EN 50332-2 as applicable.
Unless stated otherwise, the time interval T shall
be 30 s.
NOTE Test method for wireless equipment provided without
listening device should be defined.
N/A
Page 8 of 46
Report No.:17036459 001
IEC60950_1C – ATTACHMENT 1
Clause
Requirement + Test
Result - Remark
Verdict
2.7.1
Replace the subclause as follows:
Basic requirements
To protect against excessive current, shortcircuits and earth faults in PRIMARY CIRCUITS,
protective devices shall be included either as
integral parts of the equipment or as parts of the
building installation, subject to the following, a),
b) and c):
a) except as detailed in b) and c), protective
devices necessary to comply with the
requirements of 5.3 shall be included as parts of
the equipment;
b) for components in series with the mains input
to the equipment such as the supply cord,
appliance coupler, r.f.i. filter and switch, shortcircuit and earth fault protection may be provided
by protective devices in the building installation;
N/A
c) it is permitted for PLUGGABLE EQUIPMENT
TYPE B or PERMANENTLY CONNECTED
EQUIPMENT, to rely on dedicated overcurrent
and short-circuit protection in the building
installation, provided that the means of
protection, e.g. fuses or circuit breakers, is fully
specified in the installation instructions.
If reliance is placed on protection in the building
installation, the installation instructions shall so
state, except that for PLUGGABLE EQUIPMENT
TYPE A the building installation shall be regarded
as providing protection in accordance with the
rating of the wall socket outlet.
N/A
2.7.2
This subclause has been declared ‘void’.
N/A
3.2.3
Delete the NOTE in Table 3A, and delete also in
this table the conduit sizes in parentheses.
N/A
3.2.5.1
Replace
“60245 IEC 53” by “H05 RR-F”;
“60227 IEC 52” by “H03 VV-F or
H03 VVH2-F”;
“60227 IEC 53” by “H05 VV-F or
H05 VVH2-F2”.
In Table 3B, replace the first four lines by the
following:
a)
Up to and including 6 |
0,75 |
b)
Over 6 up to and including 10| (0,75)
1,0 |
c)
Over 10 up to and including 16| (1,0)
1,5
|
In the conditions applicable to Table 3B delete
a)
the words “in some countries” in condition .
In NOTE 1, applicable to Table 3B, delete the
second sentence.
N/A
Page 9 of 46
Report No.:17036459 001
IEC60950_1C – ATTACHMENT 1
Clause
Requirement + Test
3.3.4
In Table 3D, delete the fourth line: conductor
sizes for 10 to 13 A, and replace with the
following:
Over 10 up to and including 16 | 1,5 to 2,5 | 1,5 to
4
|
Delete the fifth line: conductor sizes for 13 to 16
A
N/A
4.3.13.6
Replace the existing NOTE by the following:
N/A
(A1:2010)
NOTE Z1 Attention is drawn to:
1999/519/EC: Council Recommendation on the
limitation of exposure of the general public to
electromagnetic fields 0 Hz to 300 GHz, and
2006/25/EC: Directive on the minimum health and
safety requirements regarding the exposure of workers
to risks arising from physical agents (artifical optical
radiation).
Annex H
Result - Remark
Verdict
Standards taking into account mentioned
Recommendation and Directive which demonstrate
compliance with the applicable EU Directive are
indicated in the OJEC.
N/A
Replace the last paragraph of this annex by:
At any point 10 cm from the surface of the
OPERATOR ACCESS AREA, the dose rate shall
not exceed 1 μSv/h (0,1 mR/h) (see NOTE).
Account is taken of the background level.
Replace the notes as follows:
N/A
NOTE These values appear in Directive
96/29/Euratom.
Delete NOTE 2.
Bibliography
Additional EN standards.

ZA
NORMATIVE REFERENCES TO INTERNATIONAL PUBLICATIONS WITH
THEIR CORRESPONDING EUROPEAN PUBLICATIONS

ZB ANNEX (normative)
SPECIAL NATIONAL CONDITIONS (EN)
Clause
Requirement + Test
Result - Remark
Verdict
1.2.4.1
In Denmark, certain types of Class I appliances
(see 3.2.1.1) may be provided with a plug not
establishing earthing conditions when inserted
into Danish socket-outlets.
N/A
1.2.13.14
In Norway and Sweden, for requirements see
1.7.2.1 and 7.3 of this annex.
N/A
Page 10 of 46
Report No.:17036459 001
IEC60950_1C – ATTACHMENT 1
Clause
Requirement + Test
Result - Remark
Verdict
1.5.7.1
In Finland, Norway and Sweden, resistors
bridging BASIC INSULATION in CLASS I PLUGGABLE
EQUIPMENT TYPE A must comply with the
requirements in 1.5.7.1. In addition when a single
resistor is used, the resistor must withstand the
resistor test in 1.5.7.2.
N/A
1.5.8
In Norway, due to the IT power system used (see
annex V, Figure V.7), capacitors are required to
be rated for the applicable line-to-line voltage
(230 V).
N/A
1.5.9.4
In Finland, Norway and Sweden, the third
dashed sentence is applicable only to equipment
as defined in 6.1.2.2 of this annex.
N/A
Page 11 of 46
Report No.:17036459 001
IEC60950_1C – ATTACHMENT 1
Clause
Requirement + Test
1.7.2.1
In Finland, Norway and Sweden, CLASS I
PLUGGABLE EQUIPMENT TYPE A intended for
connection to other equipment or a network shall,
if safety relies on connection to protective earth
or if surge suppressors are connected between
the network terminals and accessible parts, have
a marking stating that the equipment must be
connected to an earthed mains socket-outlet.
The marking text in the applicable countries shall
be as follows:
In Finland: "Laite on liitettävä suojakoskettimilla
varustettuun pistorasiaan"
In Norway: “Apparatet må tilkoples jordet
stikkontakt”
In Sweden: “Apparaten skall anslutas till jordat
uttag”
In Norway and Sweden, the screen of the cable
distribution system is normally not earthed at the
entrance of the building and there is normally no
equipotential bonding system within the building.
Therefore the protective earthing of the building
installation need to be isolated from the screen of
a cable distribution system.
It is however accepted to provide the insulation
external to the equipment by an adapter or an
interconnection cable with galvanic isolator,
which may be provided by e.g. a retailer.
The user manual shall then have the following or
similar information in Norwegian and Swedish
language respectively, depending on in what
country the equipment is intended to be used in:
“Equipment connected to the protective earthing
of the building installation through the mains
connection or through other equipment with a
connection to protective earthing – and to a cable
distribution system using coaxial cable, may in
some circumstances create a fire hazard.
Connection to a cable distribution system has
therefore to be provided through a device
providing electrical isolation below a certain
frequency range (galvanic isolator, see EN
60728-11).”
Result - Remark
Verdict
N/A
Page 12 of 46
Report No.:17036459 001
IEC60950_1C – ATTACHMENT 1
Clause
Requirement + Test
Result - Remark
Verdict
NOTE In Norway, due to regulation for installations of cable
distribution systems, and in Sweden, a galvanic isolator shall
provide electrical insulation below 5 MHz. The insulation shall
withstand a dielectric strength of 1,5 kV r.m.s., 50 Hz or 60
Hz, for 1 min.
Translation to Norwegian (the Swedish text will
also be accepted in Norway):
“Utstyr som er koplet til beskyttelsesjord via
nettplugg og/eller via annet jordtilkoplet
utstyr – og er tilkoplet et kabel-TV nett, kan
forårsake brannfare. For å unngå dette skal det
ved tilkopling av utstyret til kabel-TV nettet
installeres en galvanisk isolator mellom utstyret
og kabel- TV nettet.”
Translation to Swedish:
”Utrustning som är kopplad till skyddsjord via
jordat vägguttag och/eller via annan
utrustning och samtidigt är kopplad till kabel-TV
nät kan i vissa fall medfőra risk főr
brand. Főr att undvika detta skall vid anslutning
av utrustningen till kabel-TV nät
galvanisk isolator finnas mellan utrustningen och
kabel-TV nätet.”
1.7.5
In Denmark, socket-outlets for providing power to
other equipment shall be in accordance with the
Heavy Current Regulations, Section 107-2-D1,
Standard Sheet DK 1-3a, DK 1-5a or DK 1-7a,
when used on Class I equipment. For
STATIONARY EQUIPMENT the socket-outlet
shall be in accordance with Standard Sheet DK
1-1b or DK 1-5a.
For CLASS II EQUIPMENT the socket outlet shall be
in accordance with Standard Sheet DKA 1-4a.
N/A
2.2.4
In Norway, for requirements see 1.7.2.1, 6.1.2.1
and 6.1.2.2 of this annex.
N/A
2.3.2
In Finland, Norway and Sweden there are
additional requirements for the insulation. See
6.1.2.1 and 6.1.2.2 of this annex.
N/A
2.3.4
In Norway, for requirements see 1.7.2.1, 6.1.2.1
and 6.1.2.2 of this annex.
N/A
2.6.3.3
In the United Kingdom, the current rating of the
circuit shall be taken as 13 A, not 16 A.
N/A
2.7.1
In the United Kingdom, to protect against
excessive currents and short-circuits in the
PRIMARY CIRCUIT of DIRECT PLUG-IN
EQUIPMENT, tests according to 5.3 shall be
conducted, using an external protective device
rated 30 A or 32 A. If these tests fail, suitable
protective devices shall be included as integral
parts of the DIRECT PLUG-IN EQUIPMENT, so
that the requirements of 5.3 are met.
N/A
Page 13 of 46
Report No.:17036459 001
IEC60950_1C – ATTACHMENT 1
Clause
Requirement + Test
Result - Remark
Verdict
2.10.5.13
In Finland, Norway and Sweden, there are
additional requirements for the insulation, see
6.1.2.1 and 6.1.2.2 of this annex.
N/A
3.2.1.1
In Switzerland, supply cords of equipment
having a RATED CURRENT not exceeding 10 A
shall be provided with a plug complying with SEV
1011 or IEC 60884-1 and one of the following
dimension sheets:
SEV 6532-2.1991 Plug Type 15
3P+N+PE 250/400 V, 10 A
N/A
SEV 6533-2.1991 Plug Type 11
L+N
250 V, 10 A
SEV 6534-2.1991 Plug Type 12
L+N+PE
250 V, 10 A
In general, EN 60309 applies for plugs for
currents exceeding 10 A. However, a 16 A plug
and socket-outlet system is being introduced in
Switzerland, the plugs of which are according to
the following dimension sheets, published in
February 1998:
SEV 5932-2.1998: Plug Type 25 , 3L+N+PE
230/400 V, 16 A
SEV 5933-2.1998:Plug Type 21, L+N, 250 V, 16A
SEV 5934-2.1998: Plug Type 23, L+N+PE 250 V, 16 A
3.2.1.1
In Denmark, supply cords of single-phase
equipment having a rated current not
exceeding13 A shall be provided with a plug
according to the Heavy Current Regulations,
Section 107-2-D1.
CLASS I EQUIPMENT provided with socketoutlets with earth contacts or which are intended
to be used in locations where protection against
indirect contact is required according to the wiring
rules shall be provided with a plug in accordance
with standard sheet DK 2-1a or DK 2-5a.
If poly-phase equipment and single-phase
equipment having a RATED CURRENT
exceeding 13 A is provided with a supply cord
with a plug, this plug shall be in accordance with
the Heavy Current Regulations, Section 107-2-D1
or EN 60309-2.
N/A
Page 14 of 46
Report No.:17036459 001
IEC60950_1C – ATTACHMENT 1
Clause
Requirement + Test
Result - Remark
Verdict
3.2.1.1
In Spain, supply cords of single-phase equipment
having a rated current not exceeding 10 A shall
be provided with a plug according to UNE
20315:1994.
Supply cords of single-phase equipment having a
rated current not exceeding 2,5 A shall be
provided with a plug according to UNE-EN
50075:1993.
CLASS I EQUIPMENT provided with socketoutlets with earth contacts or which are intended
to be used in locations where protection against
indirect contact is required according to the wiring
rules, shall be provided with a plug in accordance
with standard UNE 20315:1994.
If poly-phase equipment is provided with a supply
cord with a plug, this plug shall be in accordance
with UNE-EN 60309-2.
N/A
3.2.1.1
In the United Kingdom, apparatus which is fitted
with a flexible cable or cord and is designed to be
connected to a mains socket conforming to BS
1363 by means of that flexible cable or cord and
plug, shall be fitted with a ‘standard plug’ in
accordance with Statutory Instrument 1768:1994
- The Plugs and Sockets etc. (Safety)
Regulations 1994, unless exempted by those
regulations.
N/A
NOTE ‘Standard plug’ is defined in SI 1768:1994 and
essentially means an approved plug conforming to BS
1363 or an approved conversion plug.
3.2.1.1
In Ireland, apparatus which is fitted with a flexible
cable or cord and is designed to be connected to
a mains socket conforming to I.S. 411 by means
of that flexible cable or cord and plug, shall be
fitted with a 13 A plug in accordance with
Statutory Instrument 525:1997 - National
Standards Authority of Ireland (section 28) (13 A
Plugs and Conversion Adaptors for Domestic
Use) Regulations 1997.
N/A
3.2.4
In Switzerland, for requirements see 3.2.1.1 of
this annex.
N/A
3.2.5.1
In the United Kingdom, a power supply cord
2
with conductor of 1,25 mm is allowed for
equipment with a rated current over 10 A and up
to and including 13 A.
N/A
3.3.4
In the United Kingdom, the range of conductor
sizes of flexible cords to be accepted by terminals
for equipment with a RATED CURRENT of over
10 A up to and including 13 A is:
2
2
• 1,25 mm to 1,5 mm nominal cross-sectional
area.
N/A
Page 15 of 46
Report No.:17036459 001
IEC60950_1C – ATTACHMENT 1
Clause
Requirement + Test
Result - Remark
Verdict
4.3.6
In the United Kingdom, the torque test is
performed using a socket outlet complying with
BS 1363 part 1:1995, including Amendment
1:1997 and Amendment 2:2003 and the plug part
of DIRECT PLUG-IN EQUIPMENT shall be
assessed to BS 1363: Part 1, 12.1, 12.2, 12.3,
12.9, 12.11, 12.12, 12.13, 12.16 and 12.17,
except that the test of 12.17 is performed at not
less than 125 °C. Where the metal earth pin is
replaced by an Insulated Shutter Opening Device
(ISOD), the requirements of clauses 22.2 and 23
also apply.
N/A
4.3.6
In Ireland, DIRECT PLUG-IN EQUIPMENT is
known as plug similar devices. Such devices
shall comply with Statutory Instrument 526:1997 National Standards Authority of Ireland (Section
28) (Electrical plugs, plug similar devices and
sockets for domestic use) Regulations, 1997.
N/A
5.1.7.1
In Finland, Norway and Sweden TOUCH
CURRENT measurement results exceeding 3,5
mA r.m.s. are permitted only for the following
equipment:
• STATIONARY PLUGGABLE EQUIPMENT
TYPE A that
is intended to be used in a RESTRICTED
ACCESS LOCATION where equipotential
bonding has been applied, for example, in a
telecommunication centre; and
has provision for a permanently connected
PROTECTIVE EARTHING CONDUCTOR; and
is provided with instructions for the
installation of that conductor by a SERVICE
PERSON;
• STATIONARY PLUGGABLE EQUIPMENT
TYPE B;
• STATIONARY PERMANENTLY CONNECTED
EQUIPMENT.
N/A
Page 16 of 46
Report No.:17036459 001
IEC60950_1C – ATTACHMENT 1
Clause
Requirement + Test
6.1.2.1
In Finland, Norway and Sweden, add the
following text between the first and second
paragraph of the compliance clause:
If this insulation is solid, including insulation
forming part of a component, it shall at least
consist of either
two layers of thin sheet material, each of
which shall pass the electric strength test below,
or
one layer having a distance through
insulation of at least 0,4 mm, which shall pass the
electric strength test below.
Alternatively for components, there is no distance
through insulation requirements for the insulation
consisting of an insulating compound completely
filling the casing, so that CLEARANCES and
CREEPAGE DISTANCES do not exist, if the
component passes the electric strength test in
accordance with the compliance clause below
and in addition
passes the tests and inspection criteria of
2.10.11 with an electric strength test of 1,5 kV
multiplied by 1,6 (the electric strength test of
2.10.10 shall be performed using 1,5 kV), and
is subject to ROUTINE TESTING for
electric strength during manufacturing, using a
test voltage of 1,5 kV.
N/A
It is permitted to bridge this insulation with an
optocoupler complying with 2.10.5.4 b).
N/A
(A1:2010)
It is permitted to bridge this insulation with a
capacitor complying with EN 60384-14:2005,
subclass Y2.
A capacitor classified Y3 according to
EN 60384-14:2005, may bridge this insulation
under the following conditions:
the insulation requirements are satisfied by
having a capacitor classified Y3 as defined by
EN 60384-14, which in addition to the Y3 testing,
is tested with an impulse test of 2,5 kV defined in
EN 60950-1:2006, 6.2.2.1;
the additional testing shall be performed
on all the test specimens as described in
EN 60384-14;
the impulse test of 2,5 kV is to be
performed before the endurance test in
EN 60384-14, in the sequence of tests as
described in EN 60384-14.
Result - Remark
Verdict
Page 17 of 46
Report No.:17036459 001
IEC60950_1C – ATTACHMENT 1
Clause
Requirement + Test
Result - Remark
Verdict
6.1.2.2
In Finland, Norway and Sweden, the exclusions
are applicable for PERMANENTLY
CONNECTED EQUIPMENT, PLUGGABLE
EQUIPMENT TYPE B and equipment intended to
be used in a RESTRICTED ACCESS LOCATION
where equipotential bonding has been applied,
e.g. in a telecommunication centre, and which
has provision for a permanently connected
PROTECTIVE EARTHING CONDUCTOR and is
provided with instructions for the installation of
that conductor by a SERVICE PERSON.
N/A
7.2
In Finland, Norway and Sweden, for
requirements see 6.1.2.1 and 6.1.2.2 of this
annex.
The term TELECOMMUNICATION NETWORK in
6.1.2 being replaced by the term CABLE
DISTRIBUTION SYSTEM.
N/A
7.3
In Norway and Sweden, for requirements see
1.2.13.14 and 1.7.2.1 of this annex.
N/A
7.3
In Norway, for installation conditions see EN
60728-11:2005.
N/A
Page 18 of 46
Report No.:17036459 001
IEC60950_1C – ATTACHMENT 1
Clause
Requirement + Test
Result - Remark
Verdict
ATTACHMENT TO TEST REPORT IEC 60950-1
CHINA NATIONAL DIFFERENCES
Information technology equipment Safety – Part 1: General requirements
Differences according to ................ :
GB 4943.1--2011
Attachment Form No. ..................... :
CN_ND_IEC60950_1A
Attachment Originator ................... :
CQC-TIRT
Master Attachment ......................... :
Date 2012-11
Copyright © 2012 IEC System for Conformity Testing and Certification of Electrical Equipment
(IECEE), Geneva, Switzerland. All rights reserved.
China National Differences
1.5. 2
Add a note behind the first dashed paragraph.
Used below 2000m
Note: A component used shall comply with related
requirements corresponding altitude of 5000m.
N/A
1.7
Add a paragraph before the last paragraph:
The required marking and instruction should be
given in normative Chinese unless otherwise
specified.
N/A
1.7.1
Amend dashed paragraph at the fifth paragraph : Class III equipment
The RATED VOLTAGE should be 220V (single
phase) or 380V (three-phases) for single rated
voltage, for RATED VOLTAGE RANGE, it should
cover 220V or 380V (three-phases), for multiple
RATED VOLTAGES, one of them should be 220V
or 380V (three-phases) and set on 220V or 380V
(three-phases) when manufactured.
And the RATED FREQUENCY or RATED
FREQUENCY RANGE should be 50Hz or include
50Hz.
Evaluated during national
approval.
N/A
Page 19 of 46
Report No.:17036459 001
IEC60950_1C – ATTACHMENT 1
Clause
Requirement + Test
Result - Remark
1.7.2.1
Used below 2000m
Add requirements of warning for equipment
intended to be used at altitude not exceeding
2000m or at non-tropical climate regions:
For equipment intended to be used at altitude not
exceeding 2000m, a warning label containing the
following or a similar appropriate wording, or a
symbol as in annex DD shall fixed to the
equipment at readily visible place.
"Only used at altitude not exceeding 2000m."
Verdict
N/A
≤2000m
For equipment intended to be used in not-tropical
climate regions, a warning label containing the
following or a similar appropriate wording, or a
symbol as in annex DD shall fixed to the
equipment at readily visible place.
"Only used in not-tropical climate regions."
If only the symbol used, the explanation of the
symbol shall be contained in the instruction
manual.
The above statements shall be given in a
language acceptable to the regions where the
apparatus is intended to be used.
2.7.1
Amended the first paragraph as:
Considered in approved
external adapter.
Protection in PRIMARY CIRCUITS against
overcurrent short-circuits and earth faults shall be
provided as an integral part of the equipment
except special provisions. And the protective
device shall meet the requirement of Clause 5.3.
Delete note of Clause 2.7.1.
N/A
Page 20 of 46
Report No.:17036459 001
IEC60950_1C – ATTACHMENT 1
Clause
Requirement + Test
Result - Remark
2.9.2
First section of Clause 2.9.2 amended as two
Considered in approved
sections:
external adapter.
Where required by 2.9.1, 2.10.8.3, 2.10.10 or
2.10.11, humidity conditioning is conducted for
120 h in a cabinet or room containing air with
ambient temperature 40±2℃ and a relative
humidity of (93±3)%. During this conditioning the
component or subassembly is not energized.
For equipment not to be operated at tropical
climatic conditions, Where required by 2.9.1,
2.10.8.3, 2.10.10 or 2.10.11, humidity conditioning
is conducted for 48 h in a cabinet or room
containing air with a relative humidity of (93±3) %.
The temperature of the air, at all places where
samples can be located, is maintained within 2 °C
of any convenient value between 20 °C and 30 °C
such that condensation does not occur.
Due to pretreatment of equipment operated at
high altitude area is humidity conditioning
withstand hot shock, specific requirements are to
be considered.
Verdict
N/A
Add note: For equipment to be operated at 2000
m - 5000m above sea level, assessment and
requirement of humidity conditioning for Insulation
material properties are considered.
2.10.3.1
Amend the third paragraph of Clause 2.10.3.1 to Considered in approved
be:
external adapter.
These requirements apply for equipment to be
operated up to 2000 m above sea level. For
equipment to be operated at more than 2000 m
above sea level and up to 5000m above sea
level, the minimum CLEARANCE shall be
multiplied by the factor 1.48 corresponding
altitude of 5000m given in Table A.2 of IEC
60664-1. For equipment to be operated at more
than 5000 m above sea level, the minimum
CLEARANCE shall be multiplied by the factor
given in Table A.2 of IEC 60664-1. Linear
interpolation is permitted between the nearest two
points in Table A.2. The calculated minimum
CLEARANCE using this multiplication factor shall
be rounded up to the next higher 0,1 mm
increment.
N/A
2.10.3.3&
2.10.3.4
Add "(applicable for altitude up to 2000m)" in
header of Table 2K、2L and 2M.
N/A
Page 21 of 46
Report No.:17036459 001
IEC60950_1C – ATTACHMENT 1
Clause
Requirement + Test
Result - Remark
Verdict
2.10.3.4
Add a new section above Table 2K and in Clause Used below 2000m
2.10.3.4:
Minimum CLEARANCES determined by above
rules apply for equipment to be operated up to
2000m above sea level. For equipment operated
at 2000 m - 5000m above sea level, the minimum
CLEARANCE shall be multiplied by the factor
1.48 corresponding altitude of 5000m given in
Table A.2 of GB/T16935.1( IEC 60664-1). For
equipment to be operated at more than 5000 m
above sea level, the minimum CLEARANCE shall
be multiplied by the factor given in Table A.2 of
GB/T16935.1.
N/A
3.2.1.1
Add a paragraph before the last paragraph:
Class III equipment
Plugs connected to AC mains supply shall comply
with GB 1002 or GB 1003 or GB/T 11918 as
applicable.
N/A
4.2.8
Clause 4.2.8 cathode ray tubes quoted Clause 18 No such equipment
of GB8898-2011.
Delete note of Clause 4.2.8.
N/A
Annex E
Amend last section:
For comparison of winding temperatures
determined by the resistance method of this
annex with the temperature limits of Table 4B,
35 °C shall be added to the calculated
temperature rise.
Add note: for equipment not to be operated at
tropical climatic conditions, 25 °C shall be added
to the calculated temperature rise to compare
with the temperature of Table 4B.
N/A
Annex G.6
Change the second section of Clause G.6 to be:
For equipment to be operated at 2000 m - 5000m
above sea level, the minimum CLEARANCE shall
be multiplied by the factor 1.48 corresponding
altitude of 5000m given in Table A.2 of
GB/T16935.1. For equipment to be operated at
more than 5000 m above sea level, the minimum
CLEARANCE shall be multiplied by the factor
given in Table A.2 of IEC 60664-1. Linear
interpolation is permitted between the nearest two
points in Table A.2. The calculated minimum
CLEARANCE using this multiplication factor shall
be rounded up to the next higher 0,1 mm
increment.
N/A
Page 22 of 46
Report No.:17036459 001
IEC60950_1C – ATTACHMENT 1
Clause
Requirement + Test
Result - Remark
Annex DD
(normative)
Added annex DD: Instructions for the new safety
warning labels.
Evaluated during national
approval.
Verdict
N/A
DD.1 Altitude warning label
Meaning of the label: Evaluation for apparatus
only based on altitude not exceeding 2000m,
therefor it’s the only operating condition applied
for the equipment .There may be some potential
safety hazard if the equipment is used at altitude
above 2000m.
DD.2 Climate warning label
Meaning of the label: Evaluation for apparatus
only based on temperate climate condition,
therefor it’s the only operating condition applied
for the equipment .There may be some potential
safety hazard if the equipment is used in tropical
climate region.
Annex EE
(informative)
Added annex EE:
Illustration relative to safety explanation in
normative Chinese、Tibetan、Mongolian、
Zhuang Language and Uighur.
N/A
Special national conditions
1.1.2
1.4.5
GB4943.1-2011 applies to equipment used
Used below 2000m
at altitudes not exceeding 5000m above sea
level,
primarily in regions with moderate or tropical
climates.
Revise the third dashed paragraph of 1.1.2 as:
——equipment intended to be used in vehicles,
on board ships or aircraft, at altitudes greater
than 5000m;
Amend the second paragraph by the following:
Class III equipment
If the equipment is intended for direct connection
to an AC mains supply, the tolerances on RATED
VOLTAGE shall be taken as +10% and -10%.
N/A
N/A
Page 23 of 46
Report No.:17036459 001
IEC60950_1C – ATTACHMENT 1
Clause
Requirement + Test
Result - Remark
1.4.12.1
Tma: The maximum ambient temperature
permitted by the manufacturer's specification, or
35 °C, whichever is greater.
Add note 1: For equipment not to be operated at
tropical climatic conditions, Tma is the maximum
ambient temperature permitted by the
manufacturer's specification, or 25 °C, whichever
is greater.
Add note 2: For equipment to be operated at
2000m-5000m above sea leave, its temperature
test conditions and temperature limits are under
consideration.
40 °C is specified by
manufacturer
Verdict
P
Page 24 of 46
Report No.:17036459 001
IEC60950_1C – ATTACHMENT 1
Clause
Requirement + Test
Result - Remark
Verdict
ATTACHMENT TO TEST REPORT IEC 60950-1
GERMANY NATIONAL DIFFERENCES
Information technology equipment – Safety –
Part 1: General requirements
Differences according to................ :
Annex ZC,
1.7.2.1
VDE 0805-1:2011-01
According to ProdSG, section 2, clause 4:
If certain rules on the use, supplementation or
maintenance of an item of technical work
equipment or ready-to-use commodity must be
observed in order to guarantee safety and health,
instructions for use in German must be supplied
when it is brought into circulation.
N/A
Page 25 of 46
Report No.:17036459 001
IEC60950_1C – ATTACHMENT 1
Clause
Requirement + Test
Result - Remark
Verdict
ATTACHMENT TO TEST REPORT IEC 60950-1
FINLAND NATIONAL DIFFERENCES
Information technology equipment – Safety –
Part 1: General requirements
Differences according to................ :
EN 60950-1:2006/A11:2009/A1:2010
Attachment Form No. ..................... :
FI_ND_IEC60950_1C
Attachment Originator ................... :
SGS Fimko Ltd
Master Attachment ......................... :
Date (2010-04)
Copyright © 2010 IEC System for Conformity Testing and Certification of Electrical Equipment
(IECEE), Geneva, Switzerland. All rights reserved.
National Differences
General
See also Group Differences (EN 60950-1:2006/A11/A1)
1.5.7.1
In Finland resistors bridging BASIC INSULATION in
CLASS I PLUGGABLE EQUIPMENT TYPE A must
comply with the requirements in 1.5.7.1. In
addition when a single resistor is used, the
resistor must withstand the resistor test in 1.5.7.2.
N/A
1.5.9.4
No such construction.
In Finland, the third dashed sentence is
applicable only to equipment as defined in 6.1.2.2
of this annex.
N/A
1.7.2.1
In Finland,CLASS I PLUGGABLE EQUIPMENT
TYPE A intended for connection to other
equipment or a network shall, if safety relies on
connection to protective earth or if surge
suppressors are connected between the network
terminals and accessible parts, have a marking
stating that the equipment must be connected to
an earthed mains socket-outlet.
The marking text in in Finland shall be as follows:
"Laite on liitettävä suojakoskettimilla varustettuun
pistorasiaan"
N/A
2.3.2
In Finland, there are additional requirements for
the insulation. See 6.1.2.1 and 6.1.2.2 of this
annex.
No TNV.
N/A
2.10.5.13
In Finland, there are additional requirements for
the insulation, see 6.1.2.1 and 6.1.2.2 of this
annex.
No TNV.
N/A
Page 26 of 46
Report No.:17036459 001
IEC60950_1C – ATTACHMENT 1
Clause
Requirement + Test
5.1.7.1
In Finland, TOUCH CURRENT measurement
results exceeding 3,5 mA r.m.s. are permitted
only for the following equipment:
• STATIONARY PLUGGABLE EQUIPMENT
TYPE A that
- is intended to be used in a RESTRICTED
ACCESS LOCATION where equipotential
bonding has been applied, for example, in a
telecommunication centre; and
- has provision for a permanently connected
PROTECTIVE EARTHING CONDUCTOR; and
- is provided with instructions for the
installation of that conductor by a SERVICE
PERSON;
• STATIONARY PLUGGABLE EQUIPMENT
TYPE B;
• STATIONARY PERMANENTLY CONNECTED
EQUIPMENT.
N/A
6.1.2.1
In Finland, add the following text between the
No TNV.
first and second paragraph of the compliance
clause:
If this insulation is solid, including insulation
forming part of a component, it shall at least
consist of either
- two layers of thin sheet material, each of
which shall pass the electric strength test below,
or
- one layer having a distance through
insulation of at least 0,4 mm, which shall pass the
electric strength test below.
Alternatively for components, there is no distance
through insulation requirement for the insulation
consisting of an insulating compound completely
filling the casing, so that CLEARANCES and
CREEPAGE DISTANCES do not exist, if the
component passes the electric strength test in
accordance with the compliance clause below
and in addition
- passes the tests and inspection criteria of
2.10.11 with an electric strength test of 1,5 kV
multiplied by 1,6 (the electric strength test of
2.10.10 shall be performed using 1,5 kV), and
- is subject to ROUTINE TESTING for electric
strength during manufacturing, using a test
voltage of 1,5 kV.
N/A
(A1:2010)
Result - Remark
Verdict
Page 27 of 46
Report No.:17036459 001
IEC60950_1C – ATTACHMENT 1
Clause
Requirement + Test
Result - Remark
Verdict
It is permitted to bridge this insulation with an
optocoupler complying with 2.10.5.4 b).
It is permitted to bridge this insulation with a
capacitor complying with EN 60384-14:2005,
subclass Y2.
A capacitor classified Y3 according to EN 6038414:2005, may bridge this insulation under the
following conditions:
- the insulation requirements are satisfied by
having a capacitor classified Y3 as defined by EN
60384-14:2005 which in addition to the Y3
testing, is tested with an impulse test of 2,5 kV
defined in EN 60950-1:2006, 6.2.2.1;
- the additional testing shall be performed on
all the test specimens as described in EN 6038414:2005;
- the impulse test of 2,5 kV is to be performed
before the endurance test in EN 60384-14:2005,
in the sequence of tests as described in EN
60384-14:2005.
6.1.2.2
In Finland, the exclusions are applicable for
PERMANENTLY CONNECTED EQUIPMENT,
PLUGGABLE EQUIPMENT TYPE B and
equipment intended to be used in a
RESTRICTED ACCESS LOCATION where
equipotential bonding has been applied, e.g. in a
telecommunication centre, and which has
provision for a permanently connected
PROTECTIVE EARTHING CONDUCTOR and is
provided with instructions for the installation of
that conductor by a SERVICE PERSON.
7.2
In Finland, for requirements see 6.1.2.1 and
Not connected to cable
6.1.2.2 of this annex.
distribution system.
The term TELECOMMUNICATION NETWORK in
6.1.2 being replaced by the term CABLE
DISTRIBUTION SYSTEM.
No TNV.
N/A
N/A
Page 28 of 46
Report No.:17036459 001
IEC60950_1C – ATTACHMENT 1
Clause
Requirement + Test
Result - Remark
Verdict
ATTACHMENT TO TEST REPORT IEC 60950-1
ISRAEL NATIONAL DIFFERENCES
Information technology equipment – Safety –
Part 1: General requirements
Differences according to................ :
SI 60950 Part 1
P
1.1.1
Replace the the text of Note 3 as follows:
Replaced.
The requirements of Israel Standard SI 60065
may also be used to meet safety requirements for
multimedia equipment. See IEC Guide 112,
Guide on the safety of multimedia equipment.
1.6
The clause is applicable with the following
addition:
1.6.1
Add following note:
In Israel, this clause is applicable subject to the
Electricity Law, 1954, its regulations and
revisions.
Added
N/A
1.7
The clause is applicable with the following
additions:
Subclause 1.7.201 shall be added at the
beginning of the clause as follows:
Added
N/A
1.7.201
Marking in the Hebrew language
The marking in the Hebrew language shall be in
accordance with the Consumer Protection Order
(Marking of goods), 1983.
In addition to the marking required by clause
1.7.1, the following details shall be marked in the
Hebrew language.
The details shall be marked on the apparatus or
on its package, or on a label properly attached to
the apparatus or on the package, by bonding or
sewing, in a manner that the label cannot be
easily removed.
1. Name of the apparatus and it commercial
designation;
2. Manufacturer’s name and address. If the
apparatus is imported, the importer’s name and
address;
3. Manufacturer’s registered trademark, if any;
4. Name of the model and serial number, if any;
5. Country of manufacture.
Evaluated during national
approval.
N/A
1.7.2.1
The following shall be added to the clause:
Evaluated during national
All the instructions and warnings related to safety approval.
shall also be written in the Hebrew language.
N/A
2
The clause is applicable with the following
additions:
N/A
N/A
Page 29 of 46
Report No.:17036459 001
IEC60950_1C – ATTACHMENT 1
Clause
Requirement + Test
Result - Remark
2.9.4
The following shall be added at the beginning of
the clause:
In Israel, according to the Electricity Law, 1954,
and the Electricity Regulations (Earthing
and means of protection against electricity of
voltages up to 1,000V) 1991, seven means of
protection against electrocution are permitted, as
follows:
1) TN-S - Network system earthing; TN-C-S Network system earthing;
2) TT - Network system earthing;
3) IT - Network Insulation Terre;
4) Isolated transformer;
5) Safety extra low voltage (SELV or ELV);
6) Residual current circuit breaker (30 mA = I);
7) Reinforced insulation; Double insulation (class
II)
Added. Considered for
approved external adapter.
2.201
Prevention of electromagnetic interference
Evaluated during national
- Prior to carrying out the tests in accordance with approval.
the clauses of this Standard, the compliance of
the apparatus with the relevant requirements
specified in the appropriate part of the Standard
series, SI 961, shall be checked.
The apparatus shall meet the requirements in the
appropriate part of the Standard series, SI 961.
- If there are components in the apparatus for the
prevention of electromagnetic interference, these
components shall not reduce the safety level of
the apparatus as required by this Standard.
3
The clause is applicable with the following
additions:
3.2.1.1
Connection to an a.c. mains supply
After the note, the following note shall be added:
Note:
In Israel, the feed plug shall comply with the
requirements of Israel Standard SI 32 Part 1.1.
3.2.1.2
Connection to a d.c. mains supply
No connected to d.c. mains
supply
At the end of the first paragraph, the following
note shall be added:
Note:
At the time of issue of this Standard, there is no
Israel Standard for connection accessories to d.c.
Annex P
Normative references
(List of relevant Israel Standards that have been
inserted in place of some of the International
Standards)
No feed plug provided.
Inserted
Verdict
P
N/A
N/A
N/A
P
Page 30 of 46
Report No.:17036459 001
IEC60950_1C – ATTACHMENT 1
Clause
Requirement + Test
Result - Remark
Verdict
J 60950-1 (H22) : 2009 TEST REPORT
(Deviations from IEC 60950-1:2001, first edition)
Special National conditions, National deviation and other information according to MITI Ordinance No. 85.
Japanese unique deviations in J60950-1(H22):2009(=JIS C 6950-1:2009)
1.1.A
Add this sub-clause
See Annex P for normative references
Added.
P
1.2
Add the following terms.
Equipment, Class 0I
Added.
N/A
1.2.4.3A
1.2.4.1
Add the following NOTE 2:
NOTE 2 – Even in the case of CLASS 0I
equipment, two-pins plug with a protective
earthing lead wire (an adapter for converting a
Class 0I equipment plug into a two-pin plug
without earthing wire) and cord sets having a
two-pin type plug with a lead wire for earthing
are also regarded as Class 0I equipment if they
are included in packaging as accessories or if
users are recommended to use them.
Added.
N/A
1.2.4.3A
Add this sub-clause:
CLASS 0I EQUIPMENT: Equipment where
protection against electric shock is achieved by:
using BASIC INSULATION, and
providing a means of connecting to the
protective earthing conductor in the building
wiring those conductive parts that are otherwise
capable of assuming HAZARDOUS VOLTAGES
if the BASIC INSULATION fails, and using a
supply cord without earthing conductor and a
plug without earthing wire although the
equipment has externally an earth terminal or a
lead wire for earthing.
Equipment provided with a cord set having a
two-pin type plug with a lead wire for earthing is
also regarded as Class 0I.
NOTE – Class 0I equipment may have a part
constructed with Double Insulation or Reinforced
Insulation as well as an operating part as SELV
circuit.
Added.
N/A
Page 31 of 46
Report No.:17036459 001
IEC60950_1C – ATTACHMENT 1
Clause
Requirement + Test
Result - Remark
1.3.2
Added.
Add the following NOTE 1 and 2:
Note1: transportable equipments or similar
equipments that are frequently transported for
use should not be considered Class I or Class 0I
equipments. However, this shall not apply to
equipments that are intended for installation by
service personnel or installation personnel.
Note 2: in consideration of the state of electrical
power distribution in Japan, it is best to avoid the
use of Class I or Class 0I devices if it is evident
that it will be difficult to connect earthing during
installation of the equipment. However, this shall
not apply to devices that are intended for
installation by service personnel or installation
personnel.
1.5.1
When safety issues apply, in the absence of
matters required by these specifications or JIS
stipulated required matters concerning safety of
related components, or in the absence of JIS
concerning the component, the component must
comply with one of the related IEC safety
requirements. However, if a component
compliant with ministerial ordinance (1962 Trade
and Commerce Ministerial Ordinance No. 85)
providing technical standards for electrical
products is being used in accordance with the
rating indicated for that component, apply
articles 1.5.4, 2.8.7 and 3.2.5; electrical power
cord sets that fit with inlets for equipments
regulated by the IEC 60320-1 Standards Sheet
must match the dimensions indicated on the
applicable IEC 60320-1 Connector Standards
Sheet.
Note 1: regarding the JIS or IEC standards
related to a component as related shall be
limited to cases where the component in
question is clearly within the scope of application
of those standards.
Verdict
N/A
P
Page 32 of 46
Report No.:17036459 001
IEC60950_1C – ATTACHMENT 1
Clause
1.5.2
Requirement + Test
Result - Remark
Verdict
P
In the case of components that are certified as
being in compliance with JIS harmonized with
the related IEC, it must be confirmed that the
component is being used correctly in accordance
with the stipulated standards. In the absence of
JIS harmonized with the related IEC,
Note 1: When using an IEC 60320-1 C.14 device
coupler with rated voltage less than 125 V and
rated current in excess of 10A, refer to 1.7.5A.
If JIS harmonized with the IEC related to the
component does not exist concurrently with the
IEC standards, or if the component is using
circuitry that does not comply with its rating, the
component must be tested in accordance with
the conditions and within equipment. The
number of samples required for testing shall
normally be the same as the number required
under similar standards.
1.5.6
Replace “IEC 60384-14:1993” to “JIS C 510114:1998 or IEC 60384-14:1993” of this SubClause
Replaced.
N/A
1.5.7.2
Replace “IEC 60384-14:1993” to “JIS C 510114:1998 or IEC 60384-14:1993” of this SubClause
Replaced.
N/A
1.5.8
Replace “IEC 60384-14:1993” to “JIS C 510114:1998 or IEC 60384-14:1993” of this SubClause
Replaced.
N/A
1.7.1
Add local importer in this sub-clause
manufacturer’s name or local importer or trademark or identification mark;
Added.
N/A
1.7.5
Replace “IEC 60083” to “IEC/TR 60083:1997 or
JIS C 8303:2007” of this Sub-Clause
Replaced.
N/A
1.7.5.A
Added.
Add this sub-clause
1.7.5A Device Coupler
When using an IEC 60320-1 C.14 device coupler
(rated current 10A) with rated voltage less than
125 V and rated current in excess of 10A, be
sure to write “Only use power supply cord sets
that are provided with this device” or a similar
statement in the user’s manual.
N/A
Page 33 of 46
Report No.:17036459 001
IEC60950_1C – ATTACHMENT 1
Clause
1.7.17A
Requirement + Test
Result - Remark
Add this sub-clause:
Verdict
Class III equipment
N/A
Replaced.
N/A
Marking for CLASS 0I EQUIPMENT
For CLASS 0I EQUIPMENT, the following
instruction shall be indicated on the visible place
of the mains plug or the main body:
“Provide an earthing connection”
Example in Japanese:
Moreover, for CLASS 0I EQUIPMENT, the
following instruction shall be indicated on the
visible place of the main body or written in the
operating instructions:
“Provide an earthing connection before the mains
plug is connected to the mains. And, when
disconnecting the earthing connection, be sure to
disconnect after pulling out the mains plug from
the mains.”
Example in Japanese:
2.1.1.1
In the Item b) of this Sub-Clause, replace “IEC
60083” to “IEC 60083 or JIS C 8303:2007”.
2.6.3.2
Add the following in front of 1 paragraph of this Class III equipment
Sub-Clause.
This also applies to the conductor of lead wire for
protective earthing of CLASS 0I EQUIPMENT.
N/A
2.6.3.4
Add the following in this Sub-Clause.
(See 2.6.3.3)
Class III equipment
N/A
2.6.4.2
Add the following after 1 paragraph of this SubClause.
However, this shall not apply when the Class 0I
equipment is equipped with a separate main
protective earthing terminal.
Class III equipment
N/A
2.6.5.4
Replace the first sentence of this Sub-Clause by: Class III equipment
Protective earthing connections of CLASS I
EQUIPMENT shall make earlier and break later
than the supply connections in each of the
following:
N/A
st
st
Page 34 of 46
Report No.:17036459 001
IEC60950_1C – ATTACHMENT 1
Clause
2.6.5.8A
Requirement + Test
Add this sub-clause:
Result - Remark
Class III equipment
Verdict
N/A
Earthing of CLASS 0I EQUIPMENT
Plugs with a lead wire for earthing shall not be
used for equipment having a rated voltage
exceeding 150V.
For plugs with a lead wire for earthing, the lead
wire shall not be earthed by a clip.
CLASS 0I EQUIPMENT shall be provided with an
earthing terminal or lead wire for earthing in the
external where easily visible.
2.10.1
Replace “IEC 60664-1” to “JIS C 0664:2003” in
NOTE of this Sub-Clause
Replaced.
P
2.10.3.1
Replace “IEC 60664-1” to “JIS C 0664:2003” in
NOTE 1 and NOTE 2
Replaced.
P
2.10.3.2
Replace “IEC 60664-1” to “JIS C 0664:2003” in
the first sentence of this Sub-Clause
Replaced.
P
3.2.3
Add the following after Table 3A of this SubAdded.
Clause.
Table 3A shall apply when a JIS C 3662 or JIS
C 3663 compliant cable is used. Other cables
that are used must be designed to allow
suitable conduits to be run in,
N/A
3.2.5.1
Add the following of this Sub-Clause.
Added.
Or must be sheathed in accordance with Section
1, Annex 1 of the ministerial ordinance (1962
Trade and Commerce Ministerial Ordinance No.
85) providing technical standards for electrical
products.
- Or must be sheathed in accordance with
Section 1, Annex 1 of the ministerial ordinance
(1962 Trade and Commerce Ministerial
Ordinance No. 85) providing technical standards
for electrical products.
- Electric cables that comply with JIS C 3662 or
JIS C 3663 have a conductor with a crosssectional area value greater than the values
provided for in Table 3B. Other electrical cables
comply with relevant wiring regulations.
Delete 1) in Table 3B.
N/A
3.3.4
Add the following in Table 3D
Added.
N/A
Note: when using JIS C 3662 or JIS C 3663compliant electrical wiring, the terminal must
enable connection of electric wiring
commensurate with the regulated sizes
Page 35 of 46
Report No.:17036459 001
IEC60950_1C – ATTACHMENT 1
Clause
Requirement + Test
Result - Remark
st
Verdict
3.3.7
Add the following after 1 paragraph of this SubClause. 。
However, this shall not apply to the external
grounding terminals of Class 0I equipment.
Added.
N/A
4.3.4
Added.
Add the following of this Sub-Clause. 。
Class 0I equipment where the values for
creepage distance and clearance distance of the
basic insulation drop further to a level lower than
that stipulated in 2.10 must be properly fixed to
withstand the mechanical stress generated in the
course of normal use.
N/A
4.3.5
Replace “IEC 60083” to “JIS C 8303:2007” in the Replaced.
first sentence of this Sub-Clause
N/A
4.3.13.3
Add the following in Table 4A
Note: JIS K 7161:1994, JIS K 7162:1994, IS K
7127:1999 are available as JIS compatible with
part of ISO527.
Added.
N/A
4..3.13.5
Replace “IEC 60825-1” to “JIS C 6802:2005 or
JIS C of this Sub-Clause
Replaced.
N/A
Replace “IEC 60825-2:2000” to “JIS C
6803:2006 or IEC 60825-2:2000” of this SubClause
Replaced.
N/A
4.5.1
Added.
Add the following to Suffix 3) of Table 4B (part
one and part two).
Note: When data concerning materials is
unavailable, Annex 4, 1 (1) 3 of “Regarding
Interpretation of Ministerial Ordinance Providing
Technical Standards for Electrical Products”
(June 19, 2008 Bureau of Commerce No. 3) may
be applied to Item 1.
P
Attachment
The insulating materials shall not be exposed to the temperature exceeding the values when the appliance is operated at rated voltage
and normal operating condition.
These values may be increased by;
8 degrees for Duty 2 appliance, and
16 degrees for Duty 3 appliance.
In order to classify the appliances, following assumptions are to be used.
Duty 1 appliances: considered to be connected to supply mains throughout the years such as refrigerators
Duty 2 appliances: considered to be connected to be in between Duty 1 and Duty 3 such as room heaters
Duty 3 appliances: considered to be connected to supply mains when it is operated for rather short time such as portable coffee mill.
Permissible temperature limits of insulating materials
Natural materials
Material
Permissible temperature limit (ºC)
Bituminous compound for filter
75, (105) 1)
Paper, cotton, silk, other natural fiber and wood
90, (105) 2)
Oil denatured natural resin
105
Page 36 of 46
Report No.:17036459 001
IEC60950_1C – ATTACHMENT 1
Clause
Requirement + Test
Result - Remark
Silica powder
500
Mica (Hard)
500, (600) 3)
(Soft)
650, (850) 3)
Verdict
Notes: 1) Value applies to thermal insulating materials.
2) Value applies to materials impregnated with varnish.
3) Value in parenthesis is applied when mechanical external force is absent.
Mica splittings and untreated mica papers
Lining
None
Adhesive
a
b
c
d
X
X
X
X
e
Permissible Temperature Limit (ºC)
f
g
130
X
155
X
180; 450, (700) 1);
X
600, (800) 2)
X
Paper
X
X
X
600, (700) 1); 700, (850) 2)
X
130
Polyethylene terephtalate film
X
130
Glass fabric
X
130
X
155
X
Polyester nonwoven fabric,
180
X
Polyester woven, and
130
X
155
Polyethylene naphthalate film
Polyamide-imide film,
X
Aramide film, and
155
X
180
Polymide film
a: with asphalt base
b: with natural resin or denatured natural resin base
c: with ceramic base
d: with oil-denatured synthetic resin, alkyd orthophatalate resin or cross-linked polyester base.
e: with silicon–denatured synthetic resin, isophatalate alkyd resin, telephatalate alkyd resin or epoxy resin.
f: with silicon resin.
g: inorganic
Notes: 1) value applies to hard mica-made heating substrate.
2) value applies to soft mica-made heating substrate.
Remarks: value in parenthesis is applied when mechanical external force is absent.
Organic materials (Thermosetting Resins)
Material
Permissible temperature limit (ºC)
laminated melamine resin mixed with glass fiber
75, (100) 1)
moulded lemaine resin mixed with:
cellulose
120
inorganics
140
laminated phenol resin with:
cotton fiber base
115, (85) 2)
paper base
120, (70) 3)
Page 37 of 46
Report No.:17036459 001
IEC60950_1C – ATTACHMENT 1
Clause
Requirement + Test
Result - Remark
polyamide cloth base
75
inorganics
140
Verdict
moulded phenol resin with:
inorganics
150, (160) 1)
others
140, (150) 1)
moulded melamine phenol resin with the gravity of less than 1.55
130
moulded urea resin mixed with cellulose
90
unsaturated polyester-casting
120
laminated unsaturated polyester mixed with inorganics
140
moulded unsaturated polyester mixed with:
other than organics
120
inorganic powder
140
glass fiber
155
epoxy resin-casting
120
laminated epoxy resin mixed with:
inorganic
130, (140) 1)
other than inorganics
110, (90) 3)
moulded epoxy resin mixed with inorganics
130
laminated diallyl phthalate resin mixed with inorganics
140
moulded diallyl phthalate resin mixed with:
other than inorganics
130
inorganic powder
150
glass fiber
155
xylene resin-casting
140
polyamide-imide film
180
laminated silicone resin mixed with inorganics
180, (220) 1)
moulded silicon resins mixed with inorganics
180, (240) 4)
polymide film
210
laminated polymide
190
polybutadiene-casting
120
moulded polybutadiene mixed with inorganics
130
laminated dipheny oxide mixed with inorganics
180
Notes: 1) Values apply to thermal insulating materials.
2) Values apply to materials with a thickness less than 0.8 mm.
3) Values apply to materials with a thickness less than 0.8 mm when treated to retard flame.
4) Values apply to materials used for thermal insulation and to seal outlets of sheathed heating wires.
Organic materials (Thermoplastic Resins)
Material
Permissible temperature limit (ºC)
methacrylic resin, cellulose resin, cellulose acetate butylate resin, ulcanise, polyethylene
50
foamed polyethylene compound for insulated conductors, polyvinyl chloride
60
polyethylene compound for insulated conductors, heat-resistant polyvinyl chloride,
75
cross-linked polyvinyl chloride compound for insulated conductors
cross-linked polyethylene, chlorinated polyethylene compound for insulated conductors
90
acrylonitrile acrylic rubber styrene resin, acrylontirile chlorinate polyethylene styrene
55
Page 38 of 46
Report No.:17036459 001
IEC60950_1C – ATTACHMENT 1
Clause
Requirement + Test
Result - Remark
Verdict
resin
acrylonitrile styrene resin, acrylonitrile butadiene resin,
acrylonitrile butadiene chlorinated polyethylene resin
polypropylene
: general
55
: reinforced with glass fiber
80
: general
105, (85) 3)
: reinforced with glass fiber
110
denatured polyphenyle oxide
: general
: reinforced with glass fiber
polyamide
polycarbonate
100
50, (70) 1)
Polystyrene
polyacetal
75
: general
100
: reinforced with glass fiber
120
: general
90
: reinforced with glass fiber
120
: general
110
: reinforced with glass fiber
120
polyethylene terephtalate
: general
: reinforced with glass fiber
polybutylene terephtalate
: general
: reinforced with glass fiber
120
130
120
135
heat resistant polyethylene terephthalate film
135
fluorinated polyvinylidene compound for insulated conductors,
polychlorotrifluoroethylene (ethylene-trifluoride resin), ethylene-tetrafleorethylene
copomylene for insulated conductors
150
tetrafluoroethylene hexafluoropropylene resin
200
polytetrafluoroethylene(ethylene-tetrafluoride), perflouroalkoxy compound for insulated
conductors
250
aramide(aromatic polyamide paper)
220
Polysulfone
140, (150) 2)
polyethylene naphthalate
155
polyallylate
: general
120
: reinforced with glass fiber
130
Notes : 1) Values apply to capacitor dielectrics.
2) Values apply to thermal insulating material
3) Values apply to materials with a thickness of less than 0.8 mm
4) Inorganic materials
Inorganic materials
Material
Permission temperature limit (ºC)
glass fiber (only alkaline free)
300
lead glass
380
borosilicate glass
490
quartz glass
800
ceramic
800, (1000) 1)
Note: 1) Value apply to materials used as electric heating elements
Rubber compounds
Page 39 of 46
Report No.:17036459 001
IEC60950_1C – ATTACHMENT 1
Clause
Requirement + Test
Result - Remark
Verdict
Material
Permission temperature limit (ºC)
natural rubber, polyurethane rubber, ebonite
60
nitrile rubber, styrene butadiene rubber, chloroprene rubber
75
butyl rubber
80
ethylene propylene (diene) rubber, chlorosulfonated polyethylene rubber
90
silicone rubber
180, (200) 1)
Note : 1) Value apply to thermal insulating material and sealing compounds for sheathed heating elements.
Sleeves, Cloth, Tapes and like
Material
Impergnat or coating
Permission temperature limit (ºC)
rayon, cellulose acetate, vinylon
adhesive, oil varnish
105
paper, cotton fabric, silk fabric,
oil varnish
105
alkyd resin varnish
120
glass fabric
(ditto)
130
paper
Iso or terephtalate
105
polyamide, polyester fabric,
polyester nonwoven fabric
polyester fabric,
polyester nonwoven fabric
alkyd resin varnish,
epoxy resin varnish,
alkyd resin varnish
polyester fabric,
(ditto)
120
Iso or terephtalate,
155
polyester nonwoven fabric
glass fabric, aramide paper
alkyd resin varnish,
epoxy resin varnish
silicone resin varnish,
silicone rubber
180
vulcanised fiber
105
heat resistant fiber
120
5.1.3
Add the following NOTE
Note: Note that domestic three-phase power
distribution systems have many delta
connections, in which case tests should be
performed using IEC 60990:1990 Figure 13 test
circuitry.
Added.
N/A
5.1.6
Table 5A
Replace Table 5A of this Sub-Clause by:
Class III equipment
N/A
Table 5A – Maximum current
Type of equipment
ALL equipment
HAND-HELD
Terminal A of
measuring instrument
connected to:
Accessible parts and
circuits not connected
to protective earth
Maximum
TOUCH
CURRENT
mA r.m.s. 1)
0,25
Maximum
PROTECTIVE
CONDUCTOR CURRENT
0,75
-
-
Page 40 of 46
Report No.:17036459 001
IEC60950_1C – ATTACHMENT 1
Clause
Requirement + Test
MOVABLE (other than HANDHELD, but including
TRANSPORTABLE
EQUIPMENT
STATIONARY,
PLUGGABLE TYPE A
ALL other STATIONARY
EQUIPMENT
not subject to the conditions of
5.1.7
subject to the conditions
of 5.1.7
HAND-HELD
Others
Result - Remark
Equipment main
protective earthing
terminal
(if any)
CLASS I EQUIPMENT
Equipment main
protective earthing
terminal
Verdict
3,5
-
3,5
-
3,5
-
-
5 % of input current
0,5
1,0
-
(if any)
CLASS 0I EQUIPMENT
1)
If peak values of TOUCH-CURRENT are measured, the maximum values obtained by multiplying the
r.m.s. values by 1,414.
Add the following after NOTE1 of this SubClause.
Refer to the accompanying document, JB, for
details concerning appropriate additional
measures,
Added.
N/A
Replace “IEC 60664-1” to “JIS C 0664 in note 4
Replaced.
N/A
7
Replace “IEC 60664-1” to “JIS C 0664:2003 of
this NOTE 3
Replaced.
N/A
7.2
Add the following
However, when all of the following criteria are
satisfied, the separation requirement and test in
6.2.1 a), b) and c) shall not be applied to the
cable distribution system.
- the applicable circuit is a TNV-1 circuit.
- the applicable circuit’s common side or
grounding side is connected to the coaxial
cable shielding, and to all accessible parts
and circuits (SELV circuits, accessible metal
parts, and limited current circuits also
applicable if they exist)
- the external conductor of the coaxial cable is
intended to be connected to the grounding
wire used for building wiring.
Replace “IEC 60664-1” to “JIS C 0664:2003”
Added.
N/A
Replaced.
N/A
Annex G 6
Replace “IEC 60664-1” to “JIS C 0664:2003”
Replaced.
N/A
Annex N
Add Note
Note: ITU-T Recommendation K.17:1996 has
been abolished and replaced with ITU-T
Recommendation K.44:2003,K.45:2003.
Added.
N/A
6
Annex G
2.1
Page 41 of 46
Report No.:17036459 001
IEC60950_1C – ATTACHMENT 1
Clause
Requirement + Test
Result - Remark
Verdict
N/A
Note: The ITU-T Recommendation K.21:1996
test circuit was replaced with K.44:2003 in July
2003.
Annex P
Add the following terms.
JIS C 5101-14:1998 Fixed capacitors for use in
electronic equipment -- Part 14: Type-specific
standards: Fixed capacitors for electromagnetic
interference suppression in electrical power
supply
Fixed capacitors for use in electronic equipment
-Part 14: Sectional specification: Fixed
capacitors for electromagnetic interference
suppression and connection to the supply mains
Added.
N/A
Replace “IEC 60065:1998” to “IEC 60065:2001”
Replaced.
N/A
Add the following terms.
JIS C 6802:2005
Added.
N/A
Add the following terms.
JIS C 6803:2006 2004.
Added.
N/A
Add the following terms.
JIS C 8303:2007
Added.
N/A
Add the following terms.
JIS S 0101:2000
Added.
N/A
Add the following terms.
Added.
N/A
Added.
N/A
Added.
N/A
ITU-T Recommendation K.44:2003 ,
Resistibility tests for telecommunication
equipment exposed to overvoltages and
overcurrents-Basic Recommendation.
Add the following terms.
ITU-T Recommendation K.45:2003,
Resistibility of telecommunication equipment
installed in the access and trunk networks to
overvoltages and overcurrents.
Annex Q
Add the following terms.
ITU-T Recommendation K.66:2004,Protection
of customer premises from overvoltages.
Annex T
Replace “IEC 60529:1989” to “JIS C 0920:2003
Replaced.
N/A
Annex W.1
Add following.
Equipment, Class 0I
Added.
N/A
Page 42 of 46
Report No.:17036459 001
IEC60950_1C – ATTACHMENT 1
Clause
Requirement + Test
Result - Remark
Verdict
Annex JA
Add Annex JA (Document shredding machines) Added.
Document shredding machines shall also comply Not Document shredding
with the requirements of this annex except those machines.
of STATIONARY EQUIPMENT used by
connecting directly to an AC MAINS SUPPLY of
three-phase 200V or more.
N/A
JA.1
Markings and instructions
In the easily visible part near the documentslot, by a method capable to make out
clearly and not easily disappeared, and by
easily understandable wording, shall
indicate the symbol of;
Added.
Not Document shredding
machines.
N/A
Added.
Not Document shredding
machines.
N/A
and, also the following precautions for use;
that use by an infant/child may cause a hazard of
injury etc.;
that a hand can be drawn into the mechanical
section for shredding when touching the
document-slot;
that clothes can be drawn into the mechanical
section for shredding when touching the
document-slot;
that hairs can be drawn into the mechanical
section for shredding when touching the
document-slot;
in case of equipment incorporating a commutator
motor, that equipment may catch fire or
explode by spraying of flammable gas.
JA.2
Inadvertent reactivation
Any safety interlock which can be operated by
means of the test finger, Figure JA.1, is
considered to cause reactivation of the hazard.
Compliance is checked by inspection and, where
necessary, by a test with the test finger, Figure
JA.1.
Page 43 of 46
Report No.:17036459 001
IEC60950_1C – ATTACHMENT 1
Clause
Requirement + Test
Figure JA.1 Test finger
Result - Remark
Verdict
Page 44 of 46
Report No.:17036459 001
IEC60950_1C – ATTACHMENT 1
Clause
JA.3
Requirement + Test
Isolating switch
Document shredding machines shall incorporate
an isolating switch complying with sub-clause
3.4.2 as the device disconnecting the power of
hazardous moving parts. For this switch, twoposition (single-use) switch or multi-position
(multifunction) switch (e.g., slide switch) may be
used.
Result - Remark
Verdict
Added.
Not Document shredding
machines.
N/A
Added.
Not Document shredding
machines.
N/A
If two-position switch, the positions for “ON” and
“OFF” shall be indicated in accordance with subclause 1.7.8. If multi-position switch, the position
for “OFF” shall be indicated in accordance with
sub-clause 1.7.8 and other positions shall be
indicated with proper terms or symbols.
Compliance is checked by inspection.
JA.4
Protection in operator access areas
Any warning shall not be used instead of the
structure for preventing access to hazardous
moving parts.
Document shredding machines shall comply with
the following requirements.
Push the test finger, Figure JA.1, into all
openings in MECHANICAL ENCLOSURES
without applying additional force. It shall not be
possible to touch hazardous moving parts with
the test finger. The document shredding machine
is installed as intended, and all face of
MECHANICAL ENCLOSURES are subjected to
this test. Before testing with the test finger,
remove the parts detachable without a tool.
Push the wedge-probe, Figure JA.2, into the
document-slot. And, against all directions of
openings, if straight-cutting type, a force of 45 N
shall apply to the probe, and 90 N if cross-cutting
type. In this case, the weight of the probe shall
not influence the test. Before testing withy the
test finger, remove the parts detachable without
a tool. It shall not be possible to touch any
hazardous moving parts, including the shredding
roller or the mechanical section for shedding,
with the probe.
Page 45 of 46
Report No.:17036459 001
IEC60950_1C – ATTACHMENT 1
Clause
Requirement + Test
Result - Remark
Verdict
(Details of the top of wedge)
Distance from the top
Thickness of probe
0
2
12
4
180
24
Note 1 - The probe shall be of changing the
thickness linearly. However, the slope shall
be changed at the respective points shown in the table.
Note 2 –The allowable dimensional tolerance of the probe is +/- 0.127 mm.
Figure JA.2 Wedge-probe
Annex JB Add Annex JB (Current state and means of
(reference handling overvoltage and overcurrent in the
installation environment)
)
The objective of this reference is not to propose
new technical standards for the device. As a
means of reducing the possibility that voltages in
excess of 1.5kV peak may be applied to the
device, these specifications provide for matters
that must be adhered to concerning the device on
the premise that it is installed in an environment
within which appropriate measures have been
taken in accordance with “ITU-T
Recommendation K.11:1993”. However, since
environments that are not commensurate with this
K.11 are often discovered domestically, this
document attempts to describe the preferred
environment and demonstrate the means for
developing the preferred installation environment,
thus contributing to its enhancement.
Added.
N/A
JB.1
JB.1 Preferred installation environment
N/A
JB.2
Current state and means of handling overvoltage
and overcurrent in the installation environment
N/A
Page 46 of 46
Report No.: 17036459 001
IEC60950_1C – ATTACHMENT 1
Clause
Requirement + Test
Result - Remark
Verdict
ATTACHMENT TO TEST REPORT IEC 60950-1
KOREA NATIONAL DIFFERENCES
Information technology equipment – Safety –
Part 1: General requirements
Differences according to................ :
K 60950-1
1.5.101
Plugs for the connection of the apparatus to the
supply mains shall comply with the Korean
requirement (KSC 8305)
Evaluated during national
approval.
N/A
8
EMC
The apparatus shall comply with the relevant
CISPR standards.
Evaluated during national
approval.
N/A
ATTACHMENT 2
Photo Documentation
Page 1 of 8
Product:
Open frame LCD monitor with touch screen
Type Designation:
KXT-ABCY-ZZZ
Figure 1. Front side view
Figure 2. Rear side view
Rev. 0
Report No.:
17036459 001
ATTACHMENT 2
Photo Documentation
Page 2 of 8
Product:
Open frame LCD monitor with touch screen
Type Designation:
KXT-ABCY-ZZZ
Figure 3. Side view
Figure 4. Touch screen view
Rev. 0
Report No.:
17036459 001
ATTACHMENT 2
Photo Documentation
Page 3 of 8
Product:
Open frame LCD monitor with touch screen
Type Designation:
KXT-ABCY-ZZZ
Figure 5. Internal view
Figure 6. Main board view
Rev. 0
Report No.:
17036459 001
ATTACHMENT 2
Photo Documentation
Page 4 of 8
Product:
Open frame LCD monitor with touch screen
Type Designation:
KXT-ABCY-ZZZ
Figure 7. Main board view
Figure 8. Connector board view
Rev. 0
Report No.:
17036459 001
ATTACHMENT 2
Photo Documentation
Page 5 of 8
Product:
Open frame LCD monitor with touch screen
Type Designation:
KXT-ABCY-ZZZ
Figure 9. Connector board view
Figure 10. Touch screen control board view
Rev. 0
Report No.:
17036459 001
ATTACHMENT 2
Photo Documentation
Page 6 of 8
Product:
Open frame LCD monitor with touch screen
Type Designation:
KXT-ABCY-ZZZ
Figure 11. Touch screen control board view
Figure 12. Inverter board view
Rev. 0
Report No.:
17036459 001
ATTACHMENT 2
Photo Documentation
Page 7 of 8
Product:
Open frame LCD monitor with touch screen
Type Designation:
KXT-ABCY-ZZZ
Figure 13. Inverter board view
Figure 14. External adapter view
Rev. 0
Report No.:
17036459 001
ATTACHMENT 2
Photo Documentation
Page 8 of 8
Product:
Open frame LCD monitor with touch screen
Type Designation:
KXT-ABCY-ZZZ
Figure 15. External adapter view
Rev. 0
Report No.:
17036459 001
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertisement