Target hadley FKVSCB2DWH Assembly Instructions Manual

hadley
2 door cabinet
style # FKVSCB2DWH (shell)
dpci # 249-16-8945
tcin # 51902572
style # FKVSCB2DGY (stone gray)
dpci # 249-16-8734
tcin # 51774487
>> assembly instructions
© 2018 Target. The Bullseye Design is a trademark of Target Brands, Inc. All rights reserved.
Congratulations on your latest Target purchase.
Now what? Don’t start sweating over this box of parts. This will be easy. We did the hard work for you.
All you need to do is follow our simple instructions and you’ll be on your way to transforming your
room in no time. Good luck—though we’re confident you won’t need it.
before you begin
1. Check for damaged or missing parts. Call 1-855-MYTGTHOME (855-698-4846) to order missing supplies.
2. Use the carton as a working surface to prevent product damage during assembly.
3. Gather all tools prior to assembly.
tools needed
2
table of contents
introduction
hardware
parts list
how to use the cam lock system
assembly
how to adjust door alignment
2
4
5
6
7-11
12
QUESTIONS? Just call 1-855-MYTGTHOME (855-698-4846) for parts and service. For faster service, have the style number and dpci number ready when calling.
3
hardware
4
(H1) x 12
wooden dowel
(H2) x 8
cam bolt
(H3) x 8
cam
(H4) x 1
allen wrench
(H5) x 27
pan head screw
(H6) x 2
knob bolt
(H7) x 8
flat head screw
(H8) x 2
knob
(H9) x 4
metal plate
(H10) x 1
magnet
(H11) x 4
bolt
(H12) x 4
lock washer
(H13) x 1
wall anchor
(H14) x 1
wall screw
(H15) x 1
truss head screw
(H16) x 1
wall strap
(H17) x 6
washer
exploded diagram
ITEM
DESCRIPTION QUANTITY
A
top panel
1
B
left side panel
1
C
right side panel
1
D
fixed shelf
1
E
bottom panel
1
F
left door
1
G
right door
1
H
back panel
2
5
how to use the cam lock system
2.
1.
Screw cam bolt into panel
Align cam bolt(s) with cross-bored
hole(s) and insert all the way until
panels are flush
4.
Rotate cam(s) clockwise 180° to
lock panels together
6
3.
Push cam into panel - arrow feature
on cam top points to panel edge
5.
Panels should be tight against each
other and connection should be rigid
step 1: attach magnet to top panel
(H5) x 2
pan head
screw
(H10) x 1
magnet
1.1. Align pan head screws with pre-drilled holes to attach magnet to top panel. Do not over tighten screws.
7
step 2: attach top panel, fixed shelf, and bottom panel to side panels
(H1) x 12
(H2) x 8
wooden dowel cam bolt
(H3) x 8
cam
(H4) x 1
allen wrench
(H12) x 4
lock washer
(H11) x 4
bolt
(H17) x 4
washer
er
2.1. Carefully tap small wooden dowels into place in top panel, fixed shelf, and bottom panel. Leave 1/2” of the dowels sticking out.
2.2. Align bolts with pre-drilled holes to attach bottom panel to side panels. Do not over tighten bolts.
2.3. Screw-In cam bolts must be screwed down flush in top panel, fixed shelf, and bottom panel.
2.4. Refer to page 6 for instructions on how to use the cam lock system.
2.5. Do not over tighten bolts.
8
step 3: attach back panel
**FAILURE TO FOLLOW ALL DIRECTIONS ON THIS PAGE MAY RESULT IN UNEVEN DOOR ALIGNMENT**
Begin by installing all of the screws along one
edge of the back panel. Next, using a square
or tape measure, make sure that the cabinet is
square. (If using a tape measure, the distance
from one corner, diagonally to the other corner
should be the same in both directions.) If not,
apply gentle pressure to the diagonally opposite
corners to shift case into alignment. Re-measure
to ensure equal distances. Install the remaining
screws, starting with the corners.
(H5) x 25
pan head
screw
(H9) x 4
metal plate
hole for anti-tip
3.1. Make sure the pan head screws go through the pre-drilled holes properly to attach back panel. Do not over tighten screws.
9
step 4: attach doors to cabinet
(H6) x 2
knob bolt
(H7) x 8
flat head
screw
(H8) x 2
knob
4.1. Align flat head screws with pre-drilled holes to attach door to cabinet. Do not over tighten screws.
4.2. Align knob bolt with pre-drilled holes to attach knob to door. Do not over tighten bolts.
10
step 5: install anti-tip kit
(H16)
Position against wall
(H13)
Mark position of strap hole on wall
(H15)
Drill 1/4” hole
(H17)
Tap in wall anchor
(H14)
(H15) x 1
truss head
screw
(H16) x 1
wall strap
(H13) x 1
wall anchor
(H14) x 1
wall screw
(H17) x 2
washer
(H17)
Fasten anti-tip strap with wall screw
provided
11
how to adjust door alignment
Tips for proper door alignment:
-Adjustable levelers will reduce minor door mis-alignments
caused by an uneven floor.
-Use a level to determine if the cabinet top is level. If not, start
with the levelers retracted and adjust them as needed.To
retract the levelers turn them counterclockwise. To extend
the levelers turn them clockwise.
-If door mis-alignment persists, refer back to Step 3 (pg. 9)
for additional information. If the cabinet is not square you will
need to repeat this step.
12
adjustable leg levelers
A. WARNING
Serious or fatal crushing injuries can occur
from furniture tip-over. To help prevent
tip-over:
• Install tip-over restraint provided.
• Place heaviest items in the lowest drawers.
• Do not set TV's or other heavy objects on top
of this product, unless the product is
specifically designed to accommodate them .
s.
b
l
50
• Never allow children to climb or hang on drawers ,
doors, or shelves.
•Never open more than one drawer at a time.
(OR)
• Do not defeat or remove the drawer interlock
system.
Use of tip-over restraints may only reduce,
but not eliminate, the risk of tip-over.
This is a permanent label. Do not remove.
s.
b
l
35
s.
b
l
35
1. This unit has been designed for the weight shown. Exceeding this recommended weight could result in
excessive “sagging” of the top. Extreme overloading can cause failure of the top and possible injury.
2. Furniture Care Instructions: Dust with a clean, lint-free cloth. Use a spray furniture polish as needed.
QUESTIONS? Just call 1-855-MYTGTHOME (855-698-4846) for parts and service. For faster service, have the style number and DPCI number ready when calling.
13
© 2018 Target. The Bullseye Design is a trademark of Target Brands, Inc. All rights reserved.