Antunes, AJ VCT-1000 Operating instructions

Antunes, AJ VCT-1000 Operating instructions
A.J. Antunes & Co.
RAPID TOASTER
MODEL VCT-200
Manufacturing Numbers 9200500/502/504
Place this manual in the Toaster section
of your Equipment Manual.
Manufactured exclusively for
McDONALD’S®
BY
A.J. ANTUNES & CO.
180 KEHOE BLVD.
CAROL STREAM, ILLINOIS 60188, U.S.A.
PHONE: 1-630-784-1000
TOLL FREE: 1-877-392-7854
FAX: 1-630-784-1650
www.ajantunes.com
ION
UT
CA
STEP
2
STEP
STEP
2
1
STEP
1
TE
MP
UP
®
C
˚F
TE
DO MP
˚C
WN
TE
SC MP
AL
E
POW
ER
US
TABLE OF CONTENTS
Operation..................................................................9
Operating Instructions .............................................9
Temperature Adjustments .......................................9
Safety Features .....................................................11
Maintenance...........................................................12
Daily Cleaning .......................................................12
Every 3 Months-Changing the Release
Sheet and Groovy Belt Wraps ............................12
Servicing Conveyor Belts ......................................15
Replacing Roller Tensioners..................................15
Replacing Conveyor Motor and Fan Blade ...........16
Troubleshooting ...............................................17-25
Wiring Diagrams...............................................26-27
Replacement Parts ...........................................28-34
Warranty ...................................................................1
Owner Information...................................................2
General....................................................................2
Warranty Information ...............................................2
Service/Technical Assistance ..................................2
Model Designation ..................................................2
Important Safety Information .................................3
Specifications ..........................................................5
Electrical Ratings ....................................................5
Electrical Cord & Plug Configurations .....................5
Dimensions..............................................................6
Installation................................................................7
Unpacking ...............................................................7
Assembling The Unit ...............................................7
Location ...................................................................8
LIMITED WARRANTY
Equipment manufactured by Roundup Food Equipment Division of A.J. Antunes & Co. has been constructed of the finest materials available and manufactured to high
quality standards. These units are warranted to be free from mechanical and electrical defects for a period of two years from date of purchase or 30 months from shipment from factory, whichever occurs first, under normal use and service, and when installed in accordance with manufacturer’s recommendations. To insure continued
proper operation of the units, follow the maintenance procedure outlined in the Owner’s Manual. During the first 12 months, all parts and non-overtime labor and travel expenses within a 50 mile/80 km (100 mile/160 km round trip) radius of the nearest Authorized Service Center are covered; during the 13th to 24th month, parts only
are covered (no labor or travel expense).
1. This warranty does not cover cost of installation, defects caused by improper storage or handling prior to placing of the Equipment. This warranty does not include
overtime charges or work done by unauthorized service agencies or personnel. This warranty does not cover normal maintenance, calibration, or regular adjustments
as specified in operating and maintenance instructions of this manual, and/or labor involved in moving adjacent objects to gain access to the Equipment. This warranty does not cover consumable items such as platen release sheet and conveyor belt wraps. Travel time and mileage in excess of 50 miles from the nearest authorized service agency is not covered under this warranty.
2. Roundup reserves the right to make changes in design or add any improvements on any product. The right is always reserved to modify equipment because of factors beyond our control and government regulations. Changes to update equipment do not constitute a warranty charge.
3. If shipment is damaged in transit, the purchaser should make a claim directly upon the carrier. Careful inspection should be made of the shipment as
soon as it arrives and visible damage should be noted upon the carrier’s receipt. Damage should be reported to the carrier. This damage is not covered
under this warranty.
4. Warranty charges do not include freight or foreign, excise, municipal or other sales or use taxes. All such freight and taxes are the responsibility of the purchaser.
5. THIS WARRANTY IS EXCLUSIVE AND IS IN LIEU OF ALL OTHER WARRANTIES, EXPRESSED OR IMPLIED, INCLUDING ANY IMPLIED WARRANTY OR MERCHANTABILITY OR FITNESS FOR A PARTICULAR PURPOSE, EACH OF WHICH IS HEREBY EXPRESSLY DISCLAIMED. THE REMEDIES DESCRIBED ABOVE
ARE EXCLUSIVE AND IN NO EVENT SHALL ROUNDUP BE LIABLE FOR SPECIAL CONSEQUENTIAL OR INCIDENTAL DAMAGES FOR THE BREACH OR
DELAY IN PERFORMANCE OF THIS WARRANTY.
This manual is for the exclusive use of licensees and employees of McDonald’s Systems, Inc.. © McDonald’s Corporation All Rights Reserved
P/N 1010710 Rev. E 9/99
Printed in the United States of America
1
A.J. Antunes & Co.
RAPID TOASTER VCT-200
OWNER INFORMATION
General
Service/Technical Assistance
This manual is produced for the Rapid Toaster Model
VCT-200 with manufacturing numbers 9200500,
9200502 & 9200504.
If you experience any problems with the installation or
operation of your unit, contact your local Roundup
Authorized Service Agency.
The Rapid Toaster Model VCT-200 is designed for contact toasting of buns. The toaster design allows the
operator to place buns on both sides of the heated
platen at the same time. Buns are placed into the bun
feeder on the top of the toaster and uniform golden
brown, warm buns are then retrieved at the base of the
toaster.
Fill in the information below and have it handy when
calling your authorized service agency for assistance.
The serial number is on the specification plate located
on the rear of the unit.
Purchased From:
Date of Purchase:
This manual provides the safety, installation and operating procedures for the Rapid Toaster Model VCT-200.
We recommend that all information contained in this
manual be read prior to installing and operating the
unit.
Model No.:
Serial No.:
Mfg. No.:
Refer to the service agency directory packaged with
your manual and fill in the information below:
The Rapid Toaster Model VCT-200 is manufactured
from the finest materials available and is assembled to
Roundup’s strict quality standards. This unit has been
tested at the factory to ensure dependable trouble-free
operation.
Authorized Service Agency
Name:
Warranty Information
Phone No.:
Please read the full text of the Limited Warranty in this
manual.
Address:
Use only genuine Roundup replacement parts in this
unit. Use of replacement parts other than those supplied by the manufacturer will void the warranty. Your
Authorized Service Agency has been factory trained
and has a complete supply of parts for this toaster.
If the unit arrives damaged, contact the carrier immediately and file a damage claim with them. Save all
packing materials when filing a claim. Freight damage
claims are the responsibility of the purchaser and are
not covered under warranty.
You may also contact the factory at 1-877-392-7854 if
you have trouble locating your local authorized service
agency.
The warranty does not extend to:
• Damages caused in shipment or damage as
result of improper use.
Model Designation
• Installation of electrical service.
• Normal maintenance as outlined in this manual.
VCT-200XX
• Malfunction resulting from improper maintenance.
TYPE OF POWER CORD
R = ROCKBESTOS
H = HARMONIZED
C = COMMERCIAL
• Damage caused by abuse or careless handling.
• Damage from moisture into electrical
components
TYPE OF PLUG
D = Domestic Pin and Sleeve
I = International Pin and Sleeve
R = Right Angle Twist-Lock
S = Straight Twist-Lock
• Damage from tampering with, removal of, or
changing any preset control or safety device.
2
P/N 1010710 Rev.E 9/99
A.J. Antunes & Co.
RAPID TOASTER VCT-200
IMPORTANT SAFETY INFORMATION
Throughout this manual, you will find the following safety words and symbols that signify important safety issues with
regards to operating or maintaining the equipment.
WARNING
WARNING
GENERAL WARNING. Indicates information important to the proper operation of
the equipment. Failure to observe may
result in damage to the equipment and/or
severe bodily injury or death.
ELECTRICAL WARNING. Indicates information relating to possible shock hazard.
Failure to observe may result in damage
to the equipment and/or severe bodily
injury or death.
CAUTION
WARNING
GENERAL CAUTION. Indicates information important to the proper operation of
the equipment. Failure to observe may
result in damage to the equipment.
HOT SURFACE WARNING. Indicates information important to the handling of
equipment and parts. Failure to observe
caution could result in personal injury.
In addition to the warnings and cautions in this manual,
use the following guidelines for safe operation of the
unit.
The following warnings and cautions appear
throughout this manual and should be carefully
observed.
• Read all instructions before using equipment.
• Turn the unit off, disconnect the power source
and allow unit to cool down before performing
any service or maintenance on the unit.
• For your safety, the equipment is furnished with a
properly grounded cord connector. Do not
attempt to defeat the grounded connector.
• The procedures in this chapter may include
the use of chemical products. These chemical
products will be highlighted with bold face letters followed by the abbreviated HCS (Hazard
Communication Standard). See Hazard
Communication Standard manual for the
appropriated Material Safety Data Sheets
(MSDS).
• Install or locate the equipment only for its intended use as described in this manual. Do not use
corrosive chemicals in this equipment.
• Do not operate this equipment if it has a damaged cord or plug, if it is not working properly, or
if it has been damaged or dropped.
• The equipment should be grounded according
to local electrical codes to prevent the possibility of electrical shock. It requires a grounded receptacle with separate electrical lines,
protected by fuses or circuit breaker of the
proper rating.
• This equipment should be serviced by qualified
personnel only. Contact the nearest Roundup
authorized service facility for adjustment or repair.
• Do not block or cover any openings on the unit.
• Do not immerse cord or plug in water.
• Bread may burn. Therefore toasters must not
be used near or below curtains or other combustible walls and materials. Failure to maintain safe operating distances may cause discoloration or combustion.
• Keep cord away from heated surfaces.
• Do not allow cord to hang over edge of table or
counter.
P/N 1010710 Rev. E 9/99
3
A.J. Antunes & Co.
RAPID TOASTER VCT-200
IMPORTANT SAFETY INFORMATION (continued)
• When installing conveyor belt wrap, be careful
not to wrap it over the upper and lower support rods or permanent damage to belt will
occur. Make sure belt wrap is positioned
UNDER the upper and lower support rods.
• WARNING ELECTRICAL SHOCK HAZARD.
FAILURE TO FOLLOW THESE INSTRUCTIONS
COULD RESULT IN SERIOUS INJURY OR
DEATH.
• Make sure both ends of belt wrap are aligned
evenly before installing belt wrap pin.
• Failure to use release sheets may result in
damage to the equipment and loss of warranty coverage.
• All electrical connections must be in accordance with local electrical codes and any
other applicable codes.
-
Electrical ground is required on this appliance.
-
Do not modify the power supply cord plug.
If it does not fit the outlet, have a proper
outlet installed by a qualified electrician.
-
Do not use an extension cord with this
appliance.
-
Check with a qualified electrician if you are
in doubt as to whether the appliance is
properly grounded.
IMPORTANT! Keep these instructions for future reference. If the unit
changes ownership, be sure this manual accompanies the equipment.
4
P/N 1010710 Rev.E 9/99
A.J. Antunes & Co.
RAPID TOASTER VCT-200
SPECIFICATIONS
Electrical Ratings
Voltage
208
Watts
4185
Amps
20.1
Hertz
50/60
220
4682
21.3
50/60
240
5570
23.2
50/60
CAUTION
All electrical connections must be in accordance
with local electrical codes and any other applicable codes.
WARNING
ELECTRICAL SHOCK HAZARD. FAILURE TO
FOLLOW THE INSTRUCTIONS IN THIS MANUAL
COULD RESULT IN SERIOUS INJURY OR DEATH.
Electrical Cord & Plug Configurations
Letter
Code*
Description
D
Pin & Sleeve
Configuration
30 Amp, 250 VAC
I
International Pin & Sleeve
•
Electrical ground is required on this appliance.
•
Do not modify the power supply cord plug. If it
does not fit the outlet, have a proper outlet
installed by a qualified electrician.
•
Do not use an extension cord with this appliance.
•
Check with a qualified electrician if you are in
doubt as to whether the appliance is properly
grounded.
IEC-309
32 Amp, 230 VAC
R
Right Angle Twist Lock
30 Amp, 250 VAC
S
Straight Twist Lock
30 Amp, 250 VAC
C
Commercial Cord
R
Rockbestos Cord
H
Harmonized Cord
* Used in Model Designation
P/N 1010710 Rev. E 9/99
5
A.J. Antunes & Co.
RAPID TOASTER VCT-200
SPECIFICATIONS (continued)
Dimensions
6
P/N 1010710 Rev.E 9/99
A.J. Antunes & Co.
RAPID TOASTER VCT-200
INSTALLATION
Unpacking
Bun Chute
1. Remove unit and all packing materials from shipping carton.
2. Open the large box (P/N 0011297). It should
contain the following:
• bun chute (Figure 1)
• bun feeder (Figure 4)
• plastic bag containing the
release sheet (Figure 4)
Hook Bun Chute over
rear Conveyor Cover
Rod
N
IO
UT
CA
3. Remove all packing materials and protective coverings from the unit and parts.
NOTE: If any parts are missing or damaged, contact
Antunes Technical Service IMMEDIATELY at 1-877392-7854
TE
MP
UP
˚F
TE
DO MP
˚C
WN
TE
SC MP
AL
E
Bun Chute
POW
ER
Assembling the Unit
1. Install the bun chute (Figure 1).
Figure 1. Installing Bun Chute
2. Remove the release sheet from the plastic bag
and lay it on a clean, flat surface. Fold the sheet
exactly in half (Figure 3).
3. Crease the sheet at the fold using only your finger
(Figure 3).
NOTE: Do not use metal tools to crease the sheet.
4. Install the release sheet by draping it over both
sides of the platen surface. The crease should be
centered directly on top of the platen (Figure 4).
Hi-Limit Reset
CAUTION
Failure to use release sheets may result in damage to the unit and loss of warranty coverage.
Figure 2. Hi-Limit Reset
5. Install the bun feeder. The bun feeder pins fit
over the tip of the platen and retain the release
sheet (Figure 4).
NOTE: Check the release sheet to make sure it is not
caught in the conveyor. Additional release sheets can
be obtained through your authorized service agency
under part no. 7000110 (3 pack) or 7000111 (10 pack).
Lay sheet on a flat surface
Fold over so ends meet
Press lightly with finger to
form crease
Figure 3. Folding Release Sheet
P/N 1010710 Rev. E 9/99
7
A.J. Antunes & Co.
RAPID TOASTER VCT-200
INSTALLATION (continued)
Location
Bun Feeder Clip
When placing the toaster into service, pay attention to
the following guidelines.
Bun Feeder
• Make sure power to the unit is off and the toaster
is at room temperature.
Platen
• Do not block or cover any openings on the unit.
Release Sheet
• Do not immerse cord or plug in water.
• Keep cord away from heated surfaces.
CA
• Do not allow cord to hang over edge of table or
counter.
UT
ION
STEP
2
STEP
STEP
2
1
STEP
1
Connect the unit to the power supply. Refer to the
specification plate for the proper voltage.
TE
MP
UP
˚F
TE
DO MP
˚C
WN
TE
SC MP
AL
E
POW
ER
CAUTION
All electrical connections must be in accordance
with local electrical codes and any other applicable codes.
Figure 4. Installing Release Sheet
WARNING
ELECTRICAL SHOCK HAZARD. FAILURE TO FOLLOW THE INSTRUCTIONS IN THIS MANUAL
COULD RESULT IN SERIOUS INJURY OR DEATH.
CAUTION
Bread may burn. Therefore toasters must not be
used near or below curtains or other combustible
walls and materials. Failure to maintain safe operating distances may cause discoloration or combustion.
8
•
Electrical ground is required on this appliance.
•
Do not modify the power supply cord plug. If it
does not fit the outlet, have a proper outlet
installed by a qualified electrician.
•
Do not use an extension cord with this appliance.
•
The toaster should be grounded according to
local electrical codes to prevent the possibility
of electrical shock. It requires a grounded
receptacle with separate electrical lines, protected by fuses or circuit breaker of the proper
rating.
•
Check with a qualified electrician if you are in
doubt as to whether the appliance is properly
grounded.
P/N 1010710 Rev.E 9/99
A.J. Antunes & Co.
RAPID TOASTER VCT-200
OPERATION
Operating Instructions
Bun Thickness
Adjustment Controls
1. Set the bun adjustment controls (Figure 6) as follows:
Heel/Club
(see Figure 7)
Crown
• Set Crown control to 3 = 11/16" (17.4 mm).
CROWN
HEEL/CLUB
4
• Set Heel/Club control to B = 7/16" (11.1 mm).
3
5
F
A
2
6
1
1 = 9/16”(14.3mm) THICKNESS
2 = 5/8” (15.9mm)
3 = 11/16” (17.4mm)
4 = 3/4” (19.1mm)
5 = 13/16” (20.6mm)
6 = 7/8” (22.2mm)
B
E
C
THICKNESS
D
A = 3/8” (09.5mm)
B = 7/16” (11.1mm)
C = 1/2” (12.7mm)
D = 9/16” (14.3mm)
E = 5/8” (15.9mm)
F = 11/16” (17.4mm)
NOTE: After initial run of 4-6 buns, adjust controls
according to the desired finished product.
2. Turn the rocker switch on (Figure 5). Allow 30
minutes warm-up time before proceeding.
CA
NOTE: The temperature display (Figure 5) will flash
“LO” until preset operating temperature is reached.
When the toaster approaches the preset temperature
of 520°F (271°C), “USE” will appear in the temperature
display and the unit is ready to toast buns.
UTI
ON
STEP
2
STEP
STEP
2
1
STEP
1
The toaster is tested and shipped with the heaters set
at a preset recommended temperature. If “USE” does
not appear in the window after warm-up period, see
Temperature Adjustments below for recommended temperature settings and to adjust temperature settings.
TE
M
UP P
˚F
˚C
TE
SC MP
ALE
TE
DO MP
WN
PO
WE
R
3. Drop buns into toaster (Figure 5). Cut sides of
heel and crown must face each other (heel/club in
front, crown in back).
Rocker Switch
Bun Landing
Area
Temperature Controls &
Temperature Display
Figure 5. VCT-200 Toaster
4. Toasted product will drop into the bun landing
area (Figure 5).
5. Test at least 4 buns before putting toaster into
service.
CROWN
4
HEEL/CLUB
3
F
A
6. Turn the rocker switch off when finished toasting.
5
Temperature Adjustments
The VCT-200 uses a platen heater and two auxiliary
heaters. The platen heater consists of a heating coil
built into the platen to toast the cut side of the bun.
The two auxiliary heaters assist in providing additional
heat to the buns. The first auxiliary heater is located
between the conveyor in the front of the toaster. The
second auxiliary heater is located between the conveyor and the rear of the unit.
6
1
1 = 9/16”(14.3mm) THICKNESS
2 = 5/8” (15.9mm)
3 = 11/16” (17.4mm)
4 = 3/4” (19.1mm)
5 = 13/16” (20.6mm)
6 = 7/8” (22.2mm)
E
B
C
THICKNESS
D
A = 3/8” (09.5mm)
B = 7/16” (11.1mm)
C = 1/2” (12.7mm)
D = 9/16” (14.3mm)
E = 5/8” (15.9mm)
F = 11/16” (17.4mm)
Figure 6. Bun Thickness Adjustment Controls
RECOMMENDED TEMPERATURES
Recommended temperature setting for the platen
heater is 560°F (293°C).
Recommended temperature setting for the auxiliary
heaters is 400°F (204°C).
NOTE: The toaster is tested and shipped with the
heaters set at the above recommended temperatures.
P/N 1010710 Rev. E 9/99
2
9
A.J. Antunes & Co.
RAPID TOASTER VCT-200
OPERATION (continued)
TEMPERATURE CONTROL PANEL
“Heat On” LED will blink on/off during warm-up and when
either platen or auxiliary heaters are calling for heat.
NOTE: Setpoint Temperature refers to the desired temperature setting.
sp-p
Pressing the TEMP UP key will display the current platen heater temperature provided the platen temperature
is over 400°F (204°C).
560
˚F
˚F
˚C
TEMP
UP
Pressing the TEMP DOWN key will display the current
auxiliary heaters temperature providing the auxiliary
heaters temperature is over 300°F (148°C).
Pressing and holding TEMP SCALE key for 3-5 seconds will switch the temperature display between
Fahrenheit (°F) and Celsius (°C).
TEMP
DOWN
TEMP
SCALE
POWER
˚C
TEMP
UP
TEMP
DOWN
TEMP
SCALE
POWER
PLATEN HEATER TEMPERATURE ADJUSTMENT
1. Turn rocker switch on and wait for temperature
display to finish the power up sequence (Figure
7).
1. SP-P (Setpoint Platen)
is displayed
2. Press and hold both TEMP UP and TEMP DOWN
keys for over 1 second until the display flashes
the setpoint temperature, then release (Figure 8).
2. Current Platen Temperature
setting is shown
sp-a
400
˚F
˚F
˚C
˚C
3. Press the TEMP UP key to raise the setpoint temperature or press the TEMP DOWN key to lower
the setpoint temperature. The setpoint temperature will adjust 1° every 0.1 seconds.
TEMP
UP
TEMP
DOWN
TEMP
SCALE
TEMP
UP
TEMP
DOWN
TEMP
SCALE
4. Release the key when the desired setpoint is displayed.
POWER
POWER
NOTE: Maximum adjustable setpoint temperature for
the platen is 570°F (298°C).
3. SP-A (Setpoint Auxiliary)
is displayed
NOTE: If no change is made within 5 seconds, the display will revert back to the previous setpoint.
AUXILIARY HEATER TEMPERATURE ADJUSTMENT
4. Current Auxiliary
Temperature setting is shown
use
lo
1. Turn rocker switch on and wait for temperature
display to finish the power up sequence (Figure
7).
˚F
˚F
˚C
TEMP
UP
2. Press and hold both TEMP UP and TEMP
SCALE keys for over 1 second until the display
flashes the setpoint temperature, then release
(Figure 9).
3. Press the TEMP UP key to raise the setpoint temperature or press the TEMP DOWN key to lower
the setpoint temperature. The setpoint temperature will adjust 1° every 0.5 seconds. Continuing
to depress the key for over two consecutive seconds will increase the adjustment speed 1° every
0.1 seconds.
TEMP
DOWN
TEMP
SCALE
POWER
5. “LO” is displayed until
platen temperature rises
above 520°F (271°C)
˚C
TEMP
UP
TEMP
DOWN
TEMP
SCALE
POWER
6. “USE” is displayed when
Platen Setpoint Temperature*
is reached
* Platen setpoint temperature must be between
520°F (271°C) and 590°F (310°) for “USE” to be displayed.
4. Release the key when the desired setpoint is displayed.
FIGURE 7. TEMPERATURE POWER UP SEQUENCE
10
P/N 1010710 Rev.E 9/99
A.J. Antunes & Co.
RAPID TOASTER VCT-200
1. Press both keys at the same
time for 1 second to start
adjustment sequence.
1. Press both keys at the same
time for 1 second to start
adjustment sequence.
551
396
˚F
˚F
˚C
2. Press TEMP UP key to raise
platen setpoint temperature.
3. Press TEMP DOWN key to
lower platen setpoint
temperature.
TEMP
UP
TEMP
DOWN
˚C
2. Press TEMP UP key to raise
auxiliary heaters setpoint
temperature.
TEMP
SCALE
3. Press TEMP DOWN key to
lower auxiliary heaters
setpoint temperature.
POWER
Figure 8. Adjusting Platen Heater
Temperature Setpoint
TEMP
UP
TEMP
DOWN
TEMP
SCALE
POWER
Figure 9. Adjusting Auxiliary Heaters
Temperature Setpoint
NOTE: Maximum adjustable setpoint temperature for
the auxiliary heater is 400°F (204°C).
“HI” displayed if platen
temperature exceeds 591°F
(310°C) or if platen thermocouple is disconnected or
“open”. Heating circuit will
turn off.
NOTE: If no change is made within 5 seconds, the display will revert back to the previous setpoint.
Safety Features
“HI” and “USE” will alternately flash if auxiliary heaters
temperature exceeds 420°F
(215°C) or if auxiliary thermocouple is disconnected or
open. Heating circuit will
NOT turn off.
HI-LIMIT RESET BUTTON
A hi-limit thermostat will turn off electrical power to the
heater and control circuits if the unit overheats. To
reset this thermostat, allow sufficient time (10-15 minutes) for the unit to cool down, then depress the reset
button located on the rear of the unit (Figure 2).
USE
HI
˚F
˚F
˚C
˚C
TEMP
UP
TEMP
DOWN
TEMP
SCALE
TEMP
UP
TEMP
DOWN
TEMP
SCALE
If the unit requires continuous resetting, contact your
Roundup authorized service agency.
FAULT MESSAGES
•
•
•
If the platen thermocouple is disconnected or
“open”, the display will read “HI” and the platen
heating circuit will turn off (Figure 10). The platen
thermocouple must be reattached or replaced.
Figure 10. “HI” Fault Message
“CHEC” will flash when
control compartment
ambient temperature is
excessive: 140°F (60°C) to
180°F (82°C). All heaters will
shut off.
If the platen heater temperature exceeds 591°F
(310°C) the display will read “HI” and the heating
circuit will turn off (Figure 10). After the toaster has
cooled down, the unit must be turned off, then back
on to restart. If this condition repeats, contact your
Roundup authorized service agency.
If the auxiliary heating temperature exceeds 420°F
(215°C) the display will alternately flash “HI” and
“USE” (Figure 10). The heating circuit will not turn
off. After the toaster has cooled down, the unit
must be turned off, then back on to restart. If this
condition repeats, contact your Roundup authorized service agency.
P/N 1010710 Rev. E 9/99
POWER
POWER
chec
˚F
˚C
TEMP
UP
TEMP
DOWN
TEMP
SCALE
POWER
Figure 11. “CHEC” Fault Message
11
A.J. Antunes & Co.
RAPID TOASTER VCT-200
OPERATION (continued)
FAULT MESSAGES (continued)
•
“PO” will flash when
incoming power drops below
190 Volts. Toaster shuts
down.
The temperature controller has an ambient temperature sensor that will shut off all heating circuits if
the control compartment ambient temperature
becomes excessive: 140°F (60°C) to 180°F (82°C).
po
˚F
˚C
TEMP
UP
TEMP
DOWN
TEMP
SCALE
When this occurs, the temperature display will flash
“CHEC” (Figure 11). To restart the unit, ambient
temperature must drop to 140°F (60°C) and the
unit must be turned off, then back on.
POWER
•
If incoming power drops below 190 Volts, the toaster will shut down and the display will read “PO”
(Figure 12). To reset, power supply must be over
190 Volts, then the unit must be turned off and
back on.
Figure 12. “PO” Fault Message
MAINTENANCE
Bun Feeder Clip
WARNING
Turn the unit off, disconnect the power source and
allow the unit to cool down before performing any
service or maintenance on the unit.
Bun Feeder
Platen
Daily cleaning
Release Sheet
1. Turn off rocker switch, unplug the power cord and
allow the unit to cool down before proceeding.
CA
2. Remove the bun feeder, front (heel) conveyor
cover, rear (crown) conveyor cover, bun chute and
lower rear cover (early models only) (Figure 1).
Wipe parts with a clean, sanitized towel.
UT
ION
STEP
2
STEP
STEP
2
1
STEP
1
TE
MP
UP
TE
DO MP
WN
˚F
˚C
TE
SC MP
AL
E
POW
ER
3. Remove the black release sheet (Figure 5) and
wipe with clean towel and APSC.
Figure 13. Removing/Installing Release Sheet
4. Wipe unit with clean towel and APSC.
5. Wipe exterior of Groovy Belt with clean towel
and APSC. Make sure to rotate Groovy Belt to
clean the entire exterior surface.
STEP 2
STEP 2
NOTE: Do not remove belt from toaster to clean.
6. Install the release sheet.
STEP 1
7. Install the front (heel) conveyor cover, rear
(crown) conveyor cover as shown in Figure 14.
Place slots of the bottom inner cover over the
lower yellow colored conveyor rod.
STEP 1
Figure 14. Conveyor Cover Installation
12
P/N 1010710 Rev.E 9/99
A.J. Antunes & Co.
RAPID TOASTER VCT-200
8. Push and slightly lift the cover so the top cover
slots slide over the top yellow colored conveyor
rods and latch into place.
Rear (Crown)
Conveyor Cover
Bun Feeder
Bun Chute
9. Install bun chute and bun feeder.
Safety
Interlock
Switch
(1 each side)
NOTE: Make sure both conveyor safety interlock
switches are activated (depressed) when the covers are
installed (Figures 15 & 20) or conveyors will not rotate.
ION
UT
CA
NOTE: Check the release sheet to make sure it is not
caught in the conveyor. Additional release sheets can
be obtained through your authorized service agency
under part no. 7000110 (3 pack) or 7000111 (10 pack).
TE
MP
UP
2
STEP
STEP
2
1
TE
DO MP
WN
˚F
˚C
TE
SC MP
AL
E
STEP
POW
ER
STEP
1
Every 3 Months – Change the Release
Sheet and Groovy Belt Wraps
GENERAL
Front (Heel) Conveyor Cover
In order to obtain the maximum life from the Groovy
Belt Wrap, other related Rapid Toaster parts must be in
good operating condition.
Figure 15. Changing Groovy Belt
CROWN
PRE-INSTALLATION
•
•
•
4
Clean the stainless steel wire conveyor belts thoroughly with all-purpose cleaner (APSC) and dry
completely.
HEEL/CLUB
3
5
Check the stainless steel wire conveyor belts for
stretching (excess slack).
2
6
1
1 = 9/16”(14.3mm) THICKNESS
2 = 5/8” (15.9mm)
3 = 11/16” (17.4mm)
4 = 3/4” (19.1mm)
5 = 13/16” (20.6mm)
6 = 7/8” (22.2mm)
Check that one roller tensioner is on the conveyor
cover and that:
- it pivots freely,
- it is not bent or worn,
- has side-to-side play.
F
A
E
B
C
THICKNESS
D
A = 3/8” (09.5mm)
B = 7/16” (11.1mm)
C = 1/2” (12.7mm)
D = 9/16” (14.3mm)
E = 5/8” (15.9mm)
F = 11/16” (17.4mm)
Figure 16. Bun Thickness Adjustment Controls
NOTE: If roller tensioner is bent, order P/N 0011311
(Qty. 1) or P/N 7000186 (Pkg. of 2) from your local
authorized service agency.
Direction of Travel
REPLACING RELEASE SHEET AND
GROOVY BELT WRAPS
1. Turn off rocker switch, unplug the power cord and
allow the unit to cool down before proceeding.
Horizontal Rib
Installed to the INSIDE
2. Remove the Bun Feeder, Front (heel) Conveyor
Cover, Rear (crown) Conveyor Cover, Bun Chute
(Figure 15).
Wavy Rib
Installed to the OUTSIDE
Figure 17. Correct Groovy Belt Wrap Installation
P/N 1010710 Rev. E 9/99
13
A.J. Antunes & Co.
RAPID TOASTER VCT-200
MAINTENANCE (continued)
3. Turn bun compression Control Knobs to “6” and
“F” (Figure 16).
Upper Yellow Support Rod
Belt Rotation
4. Move red belt wraps until connecting hinge is
exposed and centered, then remove both front
and rear belt wraps (Figure 15).
5. The Groovy Belt Wraps are not reversible and
must be installed properly in order to work correctly (Figure 17). The flap, which covers the
connecting hinge, is located on the wavy side of
the belt wrap. The wavy ribbed side should be
installed facing the outside/bun side. The straight
ribbed side should be facing towards the inside to
contact the wire conveyor. The flap should be on
the upper side of the hinge as shown.
Lower Yellow
Support Rod
6. Install the belt as shown in Figures 18 & 19.
Belt Wrap Pin
Figure 18. Installing Groovy Belt
CAUTION
Be sure conveyor belt wrap is positioned UNDER
the upper and lower support rods or damage to
the unit will occur.
CAUTION
Be sure conveyor belt wrap ends are aligned as
shown in Figure 19 or damage to the unit will
occur.
7. Set bun compression control knobs to “3” and “B”
(Figure 16).
INCORRECT
8. Install a new release sheet (Figure 13).
CORRECT
Figure 19. Aligning Belt Teeth
9. Install the front (heel) conveyor cover, rear
(crown) conveyor cover as shown in Figure 14.
Place slots of the bottom inner cover over the
lower yellow colored conveyor rod.
Safety Interlock Switch
10. Push the cover so the top cover slots slide over
the top yellow colored conveyor rods and latch
into place.
11. Install bun chute, bun feeder and lower rear cover
(early models only) (Figure 15).
CA
NOTE: Make sure both conveyor safety interlock
switches are activated (depressed) when the covers
are installed (Figures 20) or conveyors will not rotate.
UT
ION
STEP
2
STE
P1
STEP
2
STEP
1
TE
M
UP P
˚F
Figure 20. Conveyor Safety Interlock Switches
14
P/N 1010710 Rev.E 9/99
A.J. Antunes & Co.
RAPID TOASTER VCT-200
Servicing Stainless Steel Wire
Conveyor Belts
Rotation
Upper Yellow Support Rod
After a period of time, the conveyor links will wear and
the conveyor belt will stretch. This will eventually cause
the conveyor to jam as it rotates on the sprockets. This
is easily remedied by removing one or more conveyor
links from each side of the belt.
NOTE: This is not covered under warranty. It is a
user responsibility.
Large Link
P/N 0800121
When new, front conveyor has 37 large links and 4
small links (41 total); rear conveyor has 38 large links,
2 small links (40 total).
Small Link
P/N 0800204
1. Perform steps 1 - 4 under Replacing Release
Sheet and Groovy Belt Wraps on pages 13-14.
Figure 21. Removing Conveyor Belt
2. Disconnect the conveyor belt by squeezing any
two links together and unhooking both ends of
one link (Figure 21).
Acorn Nut
Teflon Tape
3. To shorten a stretched conveyor belt, remove one
1/2" link from the belt.
Tensioner Assy.
4. Reconnect by hooking both ends of the belt back
together.
Screw
NOTE: If the belt is too short to be reassembled,
remove an additional 1/2" link and install a 3/4" link.
This will shorten the belt 1/4" overall.
Replacing Stainless Steel Wire
Conveyor Belts
Spacer
Rear Conveyor Cover Assy.
1. Perform steps 1 - 4 under Replacing Release
Sheet and Groovy Belt Wraps on pages 13-14.
Figure 22. Replacing Roller Tensioner Assy.
2. Disconnect the conveyor belt by squeezing any
two links together and unhooking both ends of
one link (Figure 21).
Replacing Roller Tensioner Assemblies
1. Remove screw from acorn nut (Figure 22).
3. Place replacement conveyor belt on top sprockets. Check for correct positioning (Figure 21).
2. Remove old roller tensioner assy.
NOTE: Install conveyor belt so that the ends of the
hooks are facing down.
3. Replace tensioner assy. and reassemble.
4. Make sure the spacers are placed inside the tensioner arm. The spacers are smaller than the
holes to allow the tensioner to pivot freely.
4. Wrap conveyor belt around lower sprockets and
connect by hooking both ends of the belt back
together.
5. Perform steps 5 - 11 under Replacing Release
Sheet and Groovy Belt Wraps on pages 13-14.
P/N 1010710 Rev. E 9/99
15
A.J. Antunes & Co.
RAPID TOASTER VCT-200
MAINTENANCE (continued)
Replacing Conveyor Motor and Fan Blade
Motor Sprocket
Mounting
Bracket
NOTE: A small amount of Loctite (Blue & Red) is
required for proper gear motor installation.
TE
M
UP P
TE
DO MP
WN
1. Remove control cover.
Drive Motor
Bracket
˚F
˚C
TE
SC MP
AL
E
POW
ER
Mounting
Bracket Screw
(308P151)
2. Disconnect the motor wires and remove the drive
motor and drive motor bracket (Figure 23).
Discard the 8-32 x 5/16" mounting bracket
screws.
3. Remove the motor sprocket using a hex wrench.
Motor Mounting
Screw (310P154)
4. Remove the drive motor bracket from the gear
motor. Save the four 10-32 x 3/8" pan head
screws (P/N 310P154).
Drive Motor/Gear Reducer - Place 1 drop of
Loctite (Blue) into each threaded mounting
hole of reducer before installing.
5. Place one drop of Loctite (Blue) into each threaded hole in the gear reducer casting. Attach the
drive motor bracket to the gear reducer using the
original four 10-32 x 3/8" screws (310P154)
removed in step 3.
Fan Blade
Figure 23. Replacing Drive Motor and Fan Blade
Apply Loctite (BLUE) on setscrew of
sprocket and all other mounting screws.
6. Attach the motor sprocket to the gear reducer as
shown in Figure 23.
NOTE: Be sure sprocket setscrew is positioned on the
flat of the gear reducer shaft. Maintain the 3/16"
dimension as shown in Figure 24. Apply Loctite (Blue)
to threads of setscrew and tighten securely.
7. Using the four new 8-32 x 5/16" stainless steel
SEMS truss head screws (P/N 308P151), attach
the drive motor bracket to the mounting bracket.
DO NOT tighten screws at this time.
3/16"
(4.75 mm)
Apply only 1 drop of Loctite (RED) to
front of fan assy. after assembly. Outer
edge of fan blade hub to be flush with
end of motor shaft.
8. Place the drive chain on the sprocket and push
down on motor. Allow 1/4" (0.6 mm) play at middle of drive chain, then tighten mounting screws
while holding motor. Check drive chain play after
tightening screws.
Figure 24. Replacing Drive Motor and Fan Blade
9. Re-connect motor wires, one at a time.
10. Re-install control cover.
16
P/N 1010710 Rev.E 9/99
A.J. Antunes & Co.
RAPID TOASTER VCT-200
TROUBLESHOOTING
WARNING
To avoid possible personal injury and/or damage to the unit, inspection, test and repair of electrical equipment should be performed by qualified service personnel. The unit should be unplugged when servicing,
except when electrical tests are required. Use extreme care during electrical circuit tests. Live circuits will
be exposed.
Problem
No heat and conveyor belts
do not move.
Possible Cause
Corrective Action
Toaster is installed incorrectly.
Perform installation and operating procedures (pages 7-12).
Not enough voltage, defective power
cord, defective rocker switch.
Check receptacle for correct voltage. See
Specifications (page 5).
With unit plugged in and rocker switch on,
check for correct voltage into rocker switch.
If low or zero voltage, replace power cord.
If voltage is correct, check for correct voltage out of rocker switch. If low or no voltage, replace rocker switch.
No heat and conveyor belts
move.
Hi-limit switch tripped open.
Reset hi-limit switch (Fig. 2, page 7).
Wiring problem.
Check all electrical connections for burns,
discoloration or arcing. Replace all connections or components with damaged terminals. Replace all damaged wiring with the
same (or higher) rated wire.
Wiring problem.
Check all electrical connections for burns,
discoloration or arcing. Replace all connections or components with damaged terminals. Replace all damaged wiring with the
same (or higher) rated wire.
Inoperative temperature display
control or platen.
To check temperature display control, allow
unit to warm up for 30 minutes, then:
1.Check platen temperature at the center
of platen (with conveyor belt wrap, conveyor belt, tensioners and release sheet
removed). Use a pyrometer to confirm
temperature readings.
2.After platen temperature reaches a maximum of 559°-561°F (292°-293°C) and
auxiliary heaters reach a maximum of
399°-401°F (203°-205°C), and the temperature begins to drop, the heat indicator light on the temperature control board
should turn on. If test readings do not
agree with these figures, replace temperature display control.
P/N 1010710 Rev. E 9/99
17
A.J. Antunes & Co.
RAPID TOASTER VCT-200
Problem
No heat and conveyor belts
move (continued).
Platen is hot and conveyor
belts do not move.
Possible Cause
Corrective Action
Inoperative temperature display
control or platen (continued).
To check platen:
Ambient temperature in control
compartment too high.
“CHEC” is showing in temperature display.
Turn toaster off and allow control compartment to cool down to 140°F (60°C) and
restart toaster. Be sure cooling fan is operating and nothing is blocking the flow of
cooling air to bottom of toaster.
Toaster is installed incorrectly.
Perform installation and operating procedures (pages 7-12).
Wiring problems.
Check all electrical connections for burns,
discoloration or arcing. Replace all connections or components with damaged terminals. Replace all damaged wiring with the
same (or higher) rated wire.
Drive motor inoperable.
To check drive motor:
Use an Ohm meter to test resistance of the
platen heater (disconnect 1 wire to isolate
heater). Correct cold resistance for top two
heating elements of platen is 62.7 Ohms at
208V/725 Watts. Bottom two element
should be 69.9 Ohms at 208V/650 Watts.
The auxiliary heaters are 61.9 Ohms at
208V/700 Watts.
1.Measure resistance of motor coil.
Replace motor if coil measures either
open circuit or zero resistance.
2.If 208/240 Vac is measured across coil
but output shaft does not turn, replace
motor.
Broken drive chain or loose motor
sprocket.
Check drive chain for kinks, broken or bent
links or other damage. Check motor sprocket and drive sprockets (on drive shaft); tighten setscrew on flat of shaft if required.
Check for damaged/worn sprockets and
replace as required.
Conveyor cover assy(s). not installed.
Install conveyor cover assy(s).
Conveyor belts installed incorrectly.
Install conveyor belt to match diagram in
Fig. 21 (page 15). Be sure that ends of the
hooks are facing down.
One or both conveyor interlock switches Install conveyor cover assy. correctly.
not depressed by conveyor covers.
(Fig. 20, page 14).
Roller tensioner assy. or tensioner
bent or missing.
18
Replace roller tensioner assy(s). (33, page
32) or tensioners (6 or 7, page 28) if damaged or loose.
P/N 1010710 Rev.E 9/99
A.J. Antunes & Co.
Problem
RAPID TOASTER VCT-200
Possible Cause
Corrective Action
Platen is hot and conveyor
belts do not move
(continued).
Roller tensioner assy. or tensioner
bent or missing (continued).
Replace slide rails (45, page 28) or slide
bars (82, page 28) if worn or missing.
Conveyor belt too loose (excess
slack) or missing links When new,
front conveyor has 37 large links and
4 small links (41 total); rear conveyor
has 38 large links, 2 small links (40
total).
Remove conveyor belt (page 14). Lay belt
flat and count links. Replace entire belt if
links are damaged. If conveyor belt has too
much play, it will jam. Adjust belt length as
described under Servicing Conveyor Belts
(page 15).
Product is over-toasted or
platen heat is too high or
drop time is too slow.
Temperature set too high.
Reset platen temperature to 560°F (293°C).
Bun adjustment controls set incorrect- Measure bun thickness and set bun adjustly.
ment controls correctly (Fig. 6, page 9).
Buns sticking on release sheet or
conveyor belt wrap.
Clean or replace release sheet or conveyor
belt wrap.
Belt wrap not tacky.
Clean or replace belt wrap.
Conveyor cover assy(s) not installed.
Install conveyor cover assy(s).
Conveyor belts installed incorrectly.
Install conveyor belt to match diagram in
Fig. 21 (page 15). Be sure that ends of the
hooks are facing down.
Defective temperature display control
or defective platen.
To check temperature display control, allow
unit to warm up for 30 minutes, then:
1.Check platen temperature at the center
of platen (with conveyor belt wrap, conveyor belt, tensioners and release sheet
removed). Use a pyrometer to confirm
temperature readings.
2.After platen temperature reaches a maximum of 559°-561°F (292°-293°C) and
auxiliary heaters reach a maximum of
399°-401°F (203°-205°C), and the temperature begins to drop, the heat indicator light on the temperature control board
should turn on. If test readings do not
agree with these figures, replace temperature display control.
To check platen:
Use an Ohm meter to test resistance of the
platen heater (disconnect 1 wire to isolate
heater). Correct cold resistance for top two
heating elements of platen is 62.7 Ohms at
208V/725 Watts. Bottom two element
should be 69.9 Ohms at 208V/650 Watts.
The auxiliary heaters are 61.9 Ohms at
208V/700 Watts.
P/N 1010710 Rev. E 9/99
19
A.J. Antunes & Co.
RAPID TOASTER VCT-200
Problem
Product is over-toasted or
platen heat is too high or
drop time is too slow.
(continued).
Possible Cause
Corrective Action
Conveyor belt wraps worn and not
permitting belt to pull buns across
platen in required time.
Follow belt replacement instructions under
Replacing Release Sheet and Groovy Belt
Wraps (pages 13-14).
Defective drive motor or wrong drive
motor.
To check drive motor:
1.Measure resistance of motor coil.
Replace motor if coil measures either
open circuit or zero resistance.
2.Mark the drive motor sprocket and count
the turns per minute. Correct drive motor
speed is nine (9) turns per minute.
Product is under toasted or
platen heat is too low or
drop time is too fast.
Defective drive chain or loose
sprocket.
Check drive chain for kinks, broken or bent
links or other damage. Check motor sprocket and drive sprockets (on drive shaft); tighten setscrew on flat of shaft if required.
Check for damaged/worn sprockets and
replace as required.
Wiring problem.
Check all electrical connections for burns,
discoloration or arcing. Replace all connections or components with damaged terminals. Replace all damaged wiring with the
same (or higher) rated wire.
Conveyor belt too loose (excess
slack) or missing links When new,
front conveyor has 37 large links and
4 small links (41 total); rear conveyor
has 38 large links, 2 small links (40
total).
Remove conveyor belt (page 15). Lay belt
flat and count links. Replace entire belt if
links are damaged. If conveyor belt has too
much play, it will jam. Adjust belt length as
described under Servicing Conveyor Belts
(page 15).
Roller tensioner assy(s). or
tensioner bent or missing.
Replace roller tensioner assy(s). (33, page
32) or tensioners (6 or 7, page 28) if damaged or loose. Replace slide rails (45, page
28) or slide bars (82, page 28) if worn or
missing.
Bun adjustment controls set
incorrectly.
Measure bun thickness and set bun adjustment controls correctly (page 9).
Not enough voltage, defective power
cord, defective rocker switch.
Confirm platen temperature reading with a
pyrometer or other temperature source.
Check receptacle for correct voltage. See
Specifications (page 5).
With unit plugged in and rocker switch on,
check for correct voltage into rocker switch.
If low or zero voltage, replace power cord.
If voltage is correct, check for correct voltage out of rocker switch. If low or no voltage, replace rocker switch.
Teflon release sheet is worn.
20
If release sheet shows signs of wear or discoloration, replace sheet.
P/N 1010710 Rev.E 9/99
A.J. Antunes & Co.
Problem
Product is under-toasted or
platen heat is too low or
drop time is too fast
(continued).
RAPID TOASTER VCT-200
Possible Cause
Corrective Action
Wiring problem.
Check all electrical connections for burns,
discoloration or arcing. Replace all connections or components with damaged terminals. Replace all damaged wiring with the
same (or higher) rated wire.
Temperature display control or platen
inoperative.
To check temperature display control, allow
unit to warm up for 30 minutes, then:
1.Check platen temperature at the center
of platen (with conveyor belt wrap, conveyor belt, tensioners and release sheet
removed). Use a pyrometer to confirm
temperature readings.
2.After platen temperature reaches a maximum of 559°-561°F (292°-293°C) and
auxiliary heaters reach a maximum of
399°-401°F (203°-205°C), and the temperature begins to drop, the heat indicator light on the temperature control board
should turn on. If test readings do not
agree with these figures, replace temperature display control.
To check platen:
Use an Ohm meter to test resistance of the
platen heater (disconnect 1 wire to isolate
heater). Correct cold resistance for top two
heating elements of platen is 62.7 Ohms at
208V/725 Watts. Bottom two element
should be 69.9 Ohms at 208V/650 Watts.
The auxiliary heaters are 61.9 Ohms at
208V/700 Watts.
Conveyor drive motor inoperative or
incorrect conveyor motor installed in
toaster.
To check drive motor:
1.Measure resistance of motor coil.
Replace motor if coil measures either
open circuit or zero resistance.
2.Mark the drive motor sprocket and count
the turns per minute. Correct drive motor
speed is nine (9) turns per minute.
Product is getting stuck or
conveyor belts stop when
product is toasting.
P/N 1010710 Rev. E 9/99
Bun adjustment controls set
incorrectly.
Measure bun thickness and set bun adjustment controls correctly (pages 13-14).
Conveyor belt wrap missing or not
installed properly.
Install conveyor belt wrap properly (pages
13-14).
Conveyor belt wrap or release sheet
not clean or worn.
Clean or replace respective items. Refer to
Daily Cleaning (page 12).
Loose sprocket setscrews.
Check all sprocket screws. Retighten as
required.
Weak drive motor.
Replace drive motor.
21
A.J. Antunes & Co.
RAPID TOASTER VCT-200
Problem
Product is getting stuck or
conveyor belts stop when
product is toasting.
(continued).
Possible Cause
Not enough voltage, defective power
cord or rocker switch.
Corrective Action
Check receptacle for correct voltage. See
Specifications (page 5).
With unit plugged in and rocker switch on,
check for correct voltage into rocker switch.
If low or zero voltage, replace power cord.
If voltage is correct, check for correct voltage out of rocker switch. If low or no voltage, replace rocker switch.
Wiring problem.
Check all electrical connections for burns,
discoloration or arcing. Replace all connections or components with damaged terminals. Replace all damaged wiring with the
same (or higher) rated wire.
Conveyor drive motor inoperative or
incorrect conveyor motor installed on
toaster.
To check drive motor:
1.Measure resistance of motor coil.
Replace motor if coil measures either
open circuit or zero resistance.
2.Mark the drive motor sprocket and count
the turns per minute. Correct drive motor
speed is nine (9) turns per minute.
Conveyor drive chain loose, worn or
broken. Loose motor drive sprocket.
Check drive chain for kinks, broken or bent
links or other damage. Check motor sprocket and drive sprockets (on drive shaft); tighten setscrew on flat of shaft if required.
Check for damaged/worn sprockets and
replace as required.
Conveyor cover assy(s). not installed,
or improperly installed.
Install conveyor cover assy(s). Make sure
covers are activating (depressing) interlock
switches (Fig. 20, page 14).
Conveyor belts installed incorrectly.
Install conveyor belt to match diagram in
Fig. 21 (page 15). Be sure that ends of the
hooks are facing down.
Conveyor belt too loose (excess
slack) or missing links When new,
front conveyor has 37 large links and
4 small links (41 total); rear conveyor
has 38 large links, 2 small links (40
total).
Remove conveyor belt (page 15). Lay belt
flat and count links. Replace entire belt if
links are damaged. If conveyor belt has too
much play, it will jam. Adjust belt length as
described under Servicing Conveyor Belts
(page 15).
Roller tensioner assy(s). or
tensioner bent or missing.
Replace roller tensioner assy(s). (33, page
32) or tensioners (6 or 7, page 28) if damaged or loose. Replace slide rails (45, page
28) or slide bars (82, page 28) if worn or
missing.
22
P/N 1010710 Rev.E 9/99
A.J. Antunes & Co.
Problem
Conveyor belts are
“jumping” or “snapping”.
RAPID TOASTER VCT-200
Possible Cause
Corrective Action
Toaster is installed incorrectly.
Perform installation and operating procedures (pages 7-12).
Bun adjustment controls set
incorrectly.
Measure bun thickness and set bun adjustment controls correctly (page 9).
Conveyor drive motor inoperative or
incorrect conveyor motor installed on
toaster.
To check drive motor:
1.Measure resistance of motor coil.
Replace motor if coil measures either
open circuit or zero resistance.
2.Mark the drive motor sprocket and count
the turns per minute. Correct drive motor
speed is nine (9) turns per minute.
Temperature display shows
“LO” even after preheated
time, buns are not toasting
properly or at all.
P/N 1010710 Rev. E 9/99
Conveyor drive chain loose, worn or
broken. Loose motor drive sprocket.
Check drive chain for kinks, broken or bent
links or other damage. Check motor sprocket and drive sprockets (on drive shaft); tighten setscrew on flat of shaft if required.
Check for damaged/worn sprockets and
replace as required.
Conveyor belts installed incorrectly.
Install conveyor belt to match diagram in
Fig. 21 (page 15). Be sure that ends of the
hooks are facing down.
Conveyor belt too loose (excess
slack) or missing links When new,
front conveyor has 37 large links and
4 small links (41 total); rear conveyor
has 38 large links, 2 small links (40
total).
Remove conveyor belt (page 15). Lay belt
flat and count links. Replace entire belt if
links are damaged. If conveyor belt has too
much play, it will jam. Adjust belt length as
described under Servicing Conveyor Belts
(page 15).
Roller tensioner assy(s). or
tensioner bent or missing.
Replace roller tensioner assy(s). (33, page
32) or tensioners (6 or 7, page 28) if damaged or loose. Replace slide rails (45, page
28) or slide bars (82, page 28) if worn or
missing.
Platen temperature is below 420°F
(126°C).
Allow 20 minutes for warm-up and recheck
display.
Defective platen solid state relay (not
closing).
Replace solid state relay.
Heater platen circuit has an open circuit.
To check platen:
23
Use an Ohm meter to test resistance of the
platen heater (disconnect 1 wire to isolate
heater). Correct cold resistance for top two
heating elements of platen is 62.7 Ohms at
208V/725 Watts. Bottom two element
should be 69.9 Ohms at 208V/650 Watts.
The auxiliary heaters are 61.9 Ohms at
208V/700 Watts. Check continuity of wiring
to and from platen.
A.J. Antunes & Co.
RAPID TOASTER VCT-200
Problem
Possible Cause
Corrective Action
Temperature display shows
“LO” even after preheated
time, buns are not toasting
properly or at all (continued).
Defective control board.
Check for 15-20 VDC to platen solid state
relay at terminals 3(+) 4(-). If no VDC measured, replace control board.
Temperature display flashes
“HI” at cold start.
Inoperable control board.
If platen thermocouple circuit is not “Open”,
replace control board.
Platen thermocouple is disconnected
or open.
Reattach or replace platen thermocouple.
Temperature display flashes
”HI”after it has been reading
“USE” for awhile and hi-limit
switch trips.
Platen is overheating due to solid
state relay shorted closed.
Replace platen solid state relay.
Platen temperature is over 591°F
(310°C).
See Fault Messages (pages 11 & 12).
Buns toast fine but temperature display flashes “HI” and
“USE” after unit has been
preheated.
Inoperable control board.
If relay is not shorted, replace control board.
Auxiliary thermocouple is disconnected or “open”.
Reattach or replace auxiliary thermocouple.
Inoperable control board.
If auxiliary thermocouple is not “open”,
replace control board.
Unit is receiving low voltage, below
190 VAC.
Turn rocker switch off, then on. If display
shows “PO” again, check power cord, power
cord plug and receptacle for damage.
Replace as required.
Control board is defective.
If voltage to unit is proper, replace control
board.
Bun feeder improperly installed.
Remove and reposition bun feeder.
Conveyor belt wrap not tacky.
Clean or replace conveyor belt wrap.
Crown and/or heel improperly inserted into toaster.
Buns must be inserted with cut faces facing
each other; heel in front slot and crown in
rear slot.
Temperature display shows
“PO”.
Crown and/or heel must be
forced into toaster.
Conveyor belt wrap does not Conveyor belt wrap is installed
improperly.
fit, is difficult to install or is
not long enough.
The only item that operates
is the cooling fan (conveyor
and heat inoperable).
Check to be sure conveyor belt wrap is not
placed over upper support rod. Be sure the
open end of the flap is away from direction
and rotation, and is located toward the outside of the conveyor belt wrap
Conveyor belt wrap is damaged.
Replace conveyor belt wrap.
Hi-limit switch is tripped open.
Reset hi-limit switch (page11).
NOTE: If hi-limit trips again, contact your
authorized service agency for service.
24
P/N 1010710 Rev.E 9/99
A.J. Antunes & Co.
Problem
RAPID TOASTER VCT-200
Possible Cause
Corrective Action
Temperature display flashes Auxiliary thermocouple is disconnect“HI” and “LO” at cold startup. ed or “open”.
After preheat time it flashes
“HI” and “USE”.
Reattach or replace auxiliary thermocouple.
Temperature display flashes Auxiliary thermocouple is disconnect“HI” and “USE” after unit has ed or “open”.
been preheated, and belt
Auxiliary circuit overheating due to
wraps may start to smoke.
auxiliary solid state relay shorted
closed.
If auxiliary thermocouple circuit is not
“open”, replace control board.
Replace auxiliary solid state relay.
Display flashes “LO” constantly, buns burn and hilimit switch trips.
Platen thermocouple is grounded or
inoperable.
Replace platen thermocouple.
Control board is defective.
If platen thermocouple is not grounded,
replace control board.
Unit makes high pitched
squeal or whining noise.
Inoperable drive motor.
If noise is identified as motor, replace it.
Inoperable teflon bearings.
Replace teflon bearings.
Inoperable ball bearings.
Replace ball bearings.
P/N 1010710 Rev. E 9/99
25
A.J. Antunes & Co.
RAPID TOASTER VCT-200
WIRING DIAGRAMS
Schematic Wiring Diagram
26
P/N 1010710 Rev.E 9/99
A.J. Antunes & Co.
RAPID TOASTER VCT-200
Ladder Wiring Diagram
P/N 1010710 Rev. E 9/99
27
A.J. Antunes & Co.
RAPID TOASTER VCT-200
REPLACEMENT PARTS
19
20
64
17
18
1
42
F
8
9
B
5
O
4
7
N
10
77
60
Z
61
6
3
2
45
45
36
B
58
88
89
3
35
2
L
B
59
13
82
NOTE: Hardware List for items A-Z
and BB-EE is on page 34.
1
FF
46
T
GG
9
28
81
10
P/N 1010710 Rev.E 9/99
A.J. Antunes & Co.
Item Part No.
1
Description
RAPID TOASTER VCT-200
Qty.
Item Part No.
0011266
0800204
0800121
0011264
0800204
0800121
2150117
0011295
Conveyor Belt (Crown)
1
1/2" Pitch Link, Small
2
3/4" Pitch Link, Large
38
2
Conveyor Belt (Heel)
1
1/2" Pitch Link, Small
4
3/4" Pitch Link, Large
37
3
Idler Shaft
2
4
Conveyor Cover Assy., Front
(Heel/Club)
1
5
0011296 Conveyor Cover Assy., Rear
(Crown)
1
6
0011242 Tensioner Assy., Front
2
7
0011262 Tensioner Assy., Rear
2
8
0800332 Rod, Conveyor Cover
4
9
7000207 Sprocket w/Setscrew
8
10 7000199 Spacer Kit
2
11 7000230 Control Cover (Incl. #48)
(Used after 1/1/99)
1
11A 7000231 Control Cover (Incl. #48)
(Used before 1/1/99)
1
12 1001052 Label, Cover Installation
2
13 2150118 Drive Shaft
2
14 0700482 Power Cord/Plug, Pin & Sleeve (Std.) 1
Mfg. No. 9200500
0700495 Power Cord/Plug, Twist & Lock Angle 1
Mfg. No. 9200502
0700577 Power Cord/Plug, Twist & Lock Straight 1
Mfg. No. 9200504
15 7000171 Control Board
1
16 2150158 Ball Bearing
2
17 2150186 Teflon Bearing
6
18 0503459 Bearing Retainer/Spacer
6
19 0503376 Bearing Retainer
6
20 7000167 Bearing & Retainer Kit
1
(Incl. #17,18,19 & 79)
21 2150181 Sprocket, Drive w/Setscrew
2
22 2150187 Drive Chain
1
23 0011299 Idler Sprocket & Bearing
1
24 0501232 Bracket, Idler Sprocket
1
25 0503589 Bracket, Motor Mounting
1
26 7000175 Drive Motor Kit (Incl. #78)
1
27 2150129 Sprocket, Motor w/Setscrew
1
28 4010137 Rocker Switch, On/Off (250 VAC)
1
29 4060355 Terminal Block
1
30 405K125 Relay, Solid State
2
31 4010187 Transformer
1
32 7000183 Conveyor Belt Wrap (Pack of 2)
1
33 7000186 Roller Tensioner Assy. (Pack of 2)
1
34 0021164 Bun Feeder
1
35 0503496 Tensioner Bracket, RH
2
36 0503497 Tensioner Bracket, LH
2
37 1001006 Label, Control
1
38 100P1026 Label, Dial (Pack of 10)
1
39 2100253 Knob, Control
2
40 7000232 Cover, End (Used after 1/1/99)
1
40A 7000233 Cover, End (Used before 1/1/99)
1
41 4050214 Thermocouple Assy. (Platen)
1
P/N 1010710 Rev. E 9/99
42
43
29
44
45
0021175
7000110
7000111
0021174
7000121
46
47
48
49
50
51
52
53
54
55
56
57
58
59
60
61
62
63
64
65
66
67
68
69
70
70A
0021183
7000176
2100212
4030332
0400315
0400138
0503405
4030326
0503407
0503590
0700570
0200211
0503425
4030327
7000165
7000191
0021182
4000138
2100256
4010107
0503359
0503150
0021177
0021178
303P125
303P127
71
72
73
74
74A
1001023
0503368
0900225
0021224
7000226
75
76
77
78
79
80
81
82
83
84
85
86
87
88
89
0400312
0503367
0503321
4000170
2100252
0011301
0503455
2100259
0502199
0500464
0900228
0700579
7000203
0503495
0503507
2140146
Description
Weldment, End Housing
Release Sheet (Pack of 3)
Release Sheet (Pack of 10)
Control Housing
Slide Rail Kit (Includes 2 slide rails
for tensioners)
Conveyor Cam
Thermocouple Retainer Kit
Lifting Handle
High Limit Thermostat
Strain Relief
Locknut, 1/2"
Base, Outer
Heater, Bun Landing
Base, Inner
Bracket, Motor
Wire Set (not shown)
Gasket, Base
Bun Chute
Auxiliary Heater, Air
Auxiliary Thermocouple Kit
Platen (208 VOLT)
Weldment, Fan Duct
Axial Fan
Teflon Thrust Strip
Interlock Switch
Bracket, Relay
Heater Clip
Heat Shield, Front
Heat Shield, Rear
Hinge Pin, Belt Wrap (Pk. of 10)
Hinge Pin, Belt Wrap (Pk. of 10)
(Larger diameter used on all belts
shipped after 10-1-98)
Label, Caution Hot
Fascia, Bun Stop
Bun Stop
Inner Conveyor Cover
Inner Conveyor Cover Kit (Incl. #33,
74, 79, 83, L & T)
Teflon Damper
Clamp, Damper
Bracket, Auxiliary Thermocouple
Fan Blade, Motor
Teflon Slip Strip
Damper Support Assy.
Tension Spring, Inner
Slide Bar
Spacer
Retainer, Bearing
Bun Gauge
Wire Set
Thermocouple Retainer/Chain Guard Kit
Retainer, Tensioner Bracket, RH
Retainer, Tensioner Bracket, LH
Aerosol Lubricant CR3 3-36
(not shown)
Qty.
1
1
2
2
1
2
1
1
1
1
1
1
1
1
1
1
2
1
1
1
1
6
2
1
2
1
1
2
2
1
1
1
2
1
2
2
1
1
6
2
4
4
8
1
1
1
1
1
1
1
A.J. Antunes & Co.
RAPID TOASTER VCT-200
REPLACEMENT PARTS (continued)
5
HEIGHT
MIN.
HEIGHT
to 3 7/8"
(9.53 3/4"
cm to 9.8 cm )
to 3 7/8"
(9.53 3/4"
cm to 10.2 cm)
REGULARS
Rapid Toaster
Model VCT-100
McDONALD'S BUN GUIDE
HEIGHT
DIA.
to 1 7/8"
(4.11 5/8"
cm to 4.7 cm )
DIA.
MIN.
QUARTER POUNDER
HEIGHT
to 4"
(9.5 cm3 3/4"
to 10.2 cm)
HEIGHT
3 3/4" (9.5 CM)
3 7/8" (9.8 CM)
4" (10.2 CM)
DIA.
DIA.
BIG MAC
Your Total Toaster Supplier
1-800-253-2991
Muffin Toaster
Model MT-12
Instructions:
Place bun (untoasted) on a flat surface
Place the appropriate cut-out section of the Bun Guide over the bun
Use the markings on the Bun Guide to determine if the bun falls within
the specific range
to 1 3/4"
(3.81 1/2"
cm to 4.4 cm )
to 2 1/2"
(5.72 1/4"
cm to 6.4 cm )
A.J. Antunes & Co.
SLICE
HEIGHT (1.65/8"cm)
4
MIN.
HEIGHT
85
G
63
N O
41
18
17
3
20
64 19
47
H
F
65
EE
T
31
F
67
2
16
66
30
F
84
21
22
21
B
23
21
F
DD BB
K
P
24
CC
87*
TE
M
UP P
J 29
˚F
TE
DO MP
WN
˚C
TE
SC MP
ALE
PO
WE
T
R
H
25
1
28
37
16
F
T
27
44
27
F
23
X
21
49
78
D
15
C
55
* Units Manufactured prior to Serial Number #0812----
26
Screw 310P115
Plate 0503446
Retainer 0503444
Guard 0503518
NOTE: Hardware List for items A-Z and BB-EE is on page 34.
30
P/N 1010710 Rev.E 9/99
A.J. Antunes & Co.
Item Part No.
1
Description
RAPID TOASTER VCT-200
Qty.
Item Part No.
0011266
0800204
0800121
0011264
0800204
0800121
2150117
0011295
Conveyor Belt (Crown)
1
1/2" Pitch Link, Small
2
3/4" Pitch Link, Large
38
2
Conveyor Belt (Heel)
1
1/2" Pitch Link, Small
4
3/4" Pitch Link, Large
37
3
Idler Shaft
2
4
Conveyor Cover Assy., Front
(Heel/Club)
1
5
0011296 Conveyor Cover Assy., Rear
(Crown)
1
6
0011242 Tensioner Assy., Front
2
7
0011262 Tensioner Assy., Rear
2
8
0800332 Rod, Conveyor Cover
4
9
7000207 Sprocket w/Setscrew
8
10 7000199 Spacer Kit
2
11 7000230 Control Cover (Incl. #48)
(Used after 1/1/99)
1
11A 7000231 Control Cover (Incl. #48)
(Used before 1/1/99)
1
12 1001052 Label, Cover Installation
2
13 2150118 Drive Shaft
2
14 0700482 Power Cord/Plug, Pin & Sleeve (Std.) 1
Mfg. No. 9200500
0700495 Power Cord/Plug, Twist & Lock Angle 1
Mfg. No. 9200502
0700577 Power Cord/Plug, Twist & Lock Straight 1
Mfg. No. 9200504
15 7000171 Control Board
1
16 2150158 Ball Bearing
2
17 2150186 Teflon Bearing
6
18 0503459 Bearing Retainer/Spacer
6
19 0503376 Bearing Retainer
6
20 7000167 Bearing & Retainer Kit
1
(Incl. #17,18,19 & 79)
21 2150181 Sprocket, Drive w/Setscrew
2
22 2150187 Drive Chain
1
23 0011299 Idler Sprocket & Bearing
1
24 0501232 Bracket, Idler Sprocket
1
25 0503589 Bracket, Motor Mounting
1
26 7000175 Drive Motor Kit (Incl. #78)
1
27 2150129 Sprocket, Motor w/Setscrew
1
28 4010137 Rocker Switch, On/Off (250 VAC)
1
29 4060355 Terminal Block
1
30 405K125 Relay, Solid State
2
31 4010187 Transformer
1
32 7000183 Conveyor Belt Wrap (Pack of 2)
1
33 7000186 Roller Tensioner Assy. (Pack of 2)
1
34 0021164 Bun Feeder
1
35 0503496 Tensioner Bracket, RH
2
36 0503497 Tensioner Bracket, LH
2
37 1001006 Label, Control
1
38 100P1026 Label, Dial (Pack of 10)
1
39 2100253 Knob, Control
2
40 7000232 Cover, End (Used after 1/1/99)
1
40A 7000233 Cover, End (Used before 1/1/99)
1
41 4050214 Thermocouple Assy. (Platen)
1
P/N 1010710 Rev. E 9/99
42
43
31
44
45
0021175
7000110
7000111
0021174
7000121
46
47
48
49
50
51
52
53
54
55
56
57
58
59
60
61
62
63
64
65
66
67
68
69
70
70A
0021183
7000176
2100212
4030332
0400315
0400138
0503405
4030326
0503407
0503590
0700570
0200211
0503425
4030327
7000165
7000191
0021182
4000138
2100256
4010107
0503359
0503150
0021177
0021178
303P125
303P127
71
72
73
74
74A
1001023
0503368
0900225
0021224
7000226
75
76
77
78
79
80
81
82
83
84
85
86
87
88
89
0400312
0503367
0503321
4000170
2100252
0011301
0503455
2100259
0502199
0500464
0900228
0700579
7000203
0503495
0503507
2140146
Description
Weldment, End Housing
Release Sheet (Pack of 3)
Release Sheet (Pack of 10)
Control Housing
Slide Rail Kit (Includes 2 slide rails
for tensioners)
Conveyor Cam
Thermocouple Retainer Kit
Lifting Handle
High Limit Thermostat
Strain Relief
Locknut, 1/2"
Base, Outer
Heater, Bun Landing
Base, Inner
Bracket, Motor
Wire Set (not shown)
Gasket, Base
Bun Chute
Auxiliary Heater, Air
Auxiliary Thermocouple Kit
Platen (208 VOLT)
Weldment, Fan Duct
Axial Fan
Teflon Thrust Strip
Interlock Switch
Bracket, Relay
Heater Clip
Heat Shield, Front
Heat Shield, Rear
Hinge Pin, Belt Wrap (Pk. of 10)
Hinge Pin, Belt Wrap (Pk. of 10)
(Larger diameter used on all belts
shipped after 10-1-98)
Label, Caution Hot
Fascia, Bun Stop
Bun Stop
Inner Conveyor Cover
Inner Conveyor Cover Kit (Incl. #33,
74, 79, 83, L & T)
Teflon Damper
Clamp, Damper
Bracket, Auxiliary Thermocouple
Fan Blade, Motor
Teflon Slip Strip
Damper Support Assy.
Tension Spring, Inner
Slide Bar
Spacer
Retainer, Bearing
Bun Gauge
Wire Set
Thermocouple Retainer/Chain Guard Kit
Retainer, Tensioner Bracket, RH
Retainer, Tensioner Bracket, LH
Aerosol Lubricant CR3 3-36
(not shown)
Qty.
1
1
2
2
1
2
1
1
1
1
1
1
1
1
1
1
2
1
1
1
1
6
2
1
2
1
1
2
2
1
1
1
2
1
2
2
1
1
6
2
4
4
8
1
1
1
1
1
1
1
A.J. Antunes & Co.
RAPID TOASTER VCT-200
REPLACEMENT PARTS (continued)
40A
5
34
N
TIO
CAU
69
75
43
40
A
L
33
T
N
TIO
CAU
62
39
74
79
T
83
38
T
PLATEN
P
L
A
T
E
N
AUXILIARY
A
U
X
I
L
I
A
R
Y
11
R
L
50
4
14
N
TIO
U
CA
N
TIO
CAU
32
76
81
70
TE
M
UP P
75
PO
M
TE
DO MP
WN
˚F
˚C
TE
SC MP
AL
E
WER
51
B
48
FF
52
80
S
STEP
2
STEP
STEP
2
1
T
I
74
U
T
73
CA
UT
IO
N
STEP
1
Do
71
12
68
nn
ot
tou
ch
ho
ts
urf
ac
es
53
72
54
57
11A
48
NOTE: Hardware List for items A-Z and BB-EE is on page 34.
32
P/N 1010710 Rev.E 9/99
A.J. Antunes & Co.
Item Part No.
1
Description
RAPID TOASTER VCT-200
Qty.
Item Part No.
0011266
0800204
0800121
0011264
0800204
0800121
2150117
0011295
Conveyor Belt (Crown)
1
1/2" Pitch Link, Small
2
3/4" Pitch Link, Large
38
2
Conveyor Belt (Heel)
1
1/2" Pitch Link, Small
4
3/4" Pitch Link, Large
37
3
Idler Shaft
2
4
Conveyor Cover Assy., Front
(Heel/Club)
1
5
0011296 Conveyor Cover Assy., Rear
(Crown)
1
6
0011242 Tensioner Assy., Front
2
7
0011262 Tensioner Assy., Rear
2
8
0800332 Rod, Conveyor Cover
4
9
7000207 Sprocket w/Setscrew
8
10 7000199 Spacer Kit
2
11 7000230 Control Cover (Incl. #48)
(Used after 1/1/99)
1
11A 7000231 Control Cover (Incl. #48)
(Used before 1/1/99)
1
12 1001052 Label, Cover Installation
2
13 2150118 Drive Shaft
2
14 0700482 Power Cord/Plug, Pin & Sleeve (Std.) 1
Mfg. No. 9200500
0700495 Power Cord/Plug, Twist & Lock Angle 1
Mfg. No. 9200502
0700577 Power Cord/Plug, Twist & Lock Straight 1
Mfg. No. 9200504
15 7000171 Control Board
1
16 2150158 Ball Bearing
2
17 2150186 Teflon Bearing
6
18 0503459 Bearing Retainer/Spacer
6
19 0503376 Bearing Retainer
6
20 7000167 Bearing & Retainer Kit
1
(Incl. #17,18,19 & 79)
21 2150181 Sprocket, Drive w/Setscrew
2
22 2150187 Drive Chain
1
23 0011299 Idler Sprocket & Bearing
1
24 0501232 Bracket, Idler Sprocket
1
25 0503589 Bracket, Motor Mounting
1
26 7000175 Drive Motor Kit (Incl. #78)
1
27 2150129 Sprocket, Motor w/Setscrew
1
28 4010137 Rocker Switch, On/Off (250 VAC)
1
29 4060355 Terminal Block
1
30 405K125 Relay, Solid State
2
31 4010187 Transformer
1
32 7000183 Conveyor Belt Wrap (Pack of 2)
1
33 7000186 Roller Tensioner Assy. (Pack of 2)
1
34 0021164 Bun Feeder
1
35 0503496 Tensioner Bracket, RH
2
36 0503497 Tensioner Bracket, LH
2
37 1001006 Label, Control
1
38 100P1026 Label, Dial (Pack of 10)
1
39 2100253 Knob, Control
2
40 7000232 Cover, End (Used after 1/1/99)
1
40A 7000233 Cover, End (Used before 1/1/99)
1
41 4050214 Thermocouple Assy. (Platen)
1
P/N 1010710 Rev. E 9/99
42
43
33
44
45
0021175
7000110
7000111
0021174
7000121
46
47
48
49
50
51
52
53
54
55
56
57
58
59
60
61
62
63
64
65
66
67
68
69
70
70A
0021183
7000176
2100212
4030332
0400315
0400138
0503405
4030326
0503407
0503590
0700570
0200211
0503425
4030327
7000165
7000191
0021182
4000138
2100256
4010107
0503359
0503150
0021177
0021178
303P125
303P127
71
72
73
74
74A
1001023
0503368
0900225
0021224
7000226
75
76
77
78
79
80
81
82
83
84
85
86
87
88
89
0400312
0503367
0503321
4000170
2100252
0011301
0503455
2100259
0502199
0500464
0900228
0700579
7000203
0503495
0503507
2140146
Description
Weldment, End Housing
Release Sheet (Pack of 3)
Release Sheet (Pack of 10)
Control Housing
Slide Rail Kit (Includes 2 slide rails
for tensioners)
Conveyor Cam
Thermocouple Retainer Kit
Lifting Handle
High Limit Thermostat
Strain Relief
Locknut, 1/2"
Base, Outer
Heater, Bun Landing
Base, Inner
Bracket, Motor
Wire Set (not shown)
Gasket, Base
Bun Chute
Auxiliary Heater, Air
Auxiliary Thermocouple Kit
Platen (208 VOLT)
Weldment, Fan Duct
Axial Fan
Teflon Thrust Strip
Interlock Switch
Bracket, Relay
Heater Clip
Heat Shield, Front
Heat Shield, Rear
Hinge Pin, Belt Wrap (Pk. of 10)
Hinge Pin, Belt Wrap (Pk. of 10)
(Larger diameter used on all belts
shipped after 10-1-98)
Label, Caution Hot
Fascia, Bun Stop
Bun Stop
Inner Conveyor Cover
Inner Conveyor Cover Kit (Incl. #33,
74, 79, 83, L & T)
Teflon Damper
Clamp, Damper
Bracket, Auxiliary Thermocouple
Fan Blade, Motor
Teflon Slip Strip
Damper Support Assy.
Tension Spring, Inner
Slide Bar
Spacer
Retainer, Bearing
Bun Gauge
Wire Set
Thermocouple Retainer/Chain Guard Kit
Retainer, Tensioner Bracket, RH
Retainer, Tensioner Bracket, LH
Aerosol Lubricant CR3 3-36
(not shown)
Qty.
1
1
2
2
1
2
1
1
1
1
1
1
1
1
1
1
2
1
1
1
1
6
2
1
2
1
1
2
2
1
1
1
2
1
2
2
1
1
6
2
4
4
8
1
1
1
1
1
1
1
A.J. Antunes & Co.
RAPID TOASTER VCT-200
REPLACEMENT PARTS (continued)
Parts Identification
Axial Fan
Auxiliary Heater
Interlock Switch
Drive Chain
Transformer
Idler Sprocket (5/16" Bore)
Sprocket (1/2" Bore)
Sprocket (1/2" Bore)
Auxiliary Relay
Platen Relay
Temperature Control
Drive Motor Assy.
Rocker Switch
(Power On/Off)
Hi-Limit Thermostat
Fan Blade
Hardware List
The following items are only available in packages of 10.
Item
A
B
C
D
E
F
G
H
I
J
K
L
M
N
O
P
Part
No.
100P864
308P115
310P154
304P105
406P107
308P143
310P103
310P140
308P101
306P101
306P123
308P145
100P900
325P104
325P109
308P124
Description
Label, Caution Hot
Screw, #8-32 x 3/8" (10 mm)
Screw, #10-32 x 3/8"
Nut, #4-40, "KEPS"
Cable Tie
Nut, #8-32, "KEPS"
Screw, #10-32 x 1/4"
Washer, #10
Nut, #8-32
Nut, Hex, #6-32
Screw, #6-32 x 7/8"
Nut, Hex Acorn, #8-32
Label, Service
Washer, 1/4"
Screw, 1/4-20 x 1/2"
Screw, 1-Way, #8-32 x 1/2"
Qty.
Item
1
10
4
1
1
3
1
3
3
1
1
1
1
1
1
1
R
S
T
U
V
W
X
Y
10P1022
212P111
308P133
308P120
308P104
308P105
331P103
040P111
Z
BB
CC
DD
EE
FF
GG
306P105
331P106
212P118
331P101
300P102
306P104
325P163
34
Part
No.
Description
Qty.
Label, Heaters
Spacer
Screw, #8-32 x 1/4"
Screw, #8-32 x 5/8"
Screw, #8-32 x 3/8"
Screw, #8-32 x 1/2"
Shoulder Bolt, 5/16-18 x l"
Bushing, Shorty, 1/2"
(not shown)
Screw, #6-32 x 1/2"
Lockwasher, 5/16"
Flat Washer, 5/16"
Nut, Hex, 5/16 x 18"
Nut, Tinnerman
Screw, #6-32 x 1/4"
Setscrew, 1/4-28 x 5/16"
1
1
1
1
1
1
1
1
1
1
1
1
2
8
8
P/N 1010710 Rev.E 9/99
A.J. Antunes & Co.
RAPID TOASTER VCT-200
NOTES
P/N 1010710 Rev. E 9/99
35
A.J. Antunes & Co.
RAPID TOASTER
MODEL VCT-200
Manufacturing Numbers 9200500/502/504
NOTES
36
P/N 1010710 Rev.E 9/99
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertisement