Comfort Zone CZ463EBK Manual

CZ463EBK
ENERGY SAVE TECHNOLOGY
helps save energy and reduces
your heating costs.
ENERGY SAVE TECHNOLOGY
provides comfortable heating
using 30% less energy than a
standard heater!*
* Note: Compared to a 1,500 watt space
heater on high heat.
Patent Pending
Ceramic Heater
Features:
• Adjustable Thermostat
• Three Heat Settings:
•
•
•
•
•
•
Energy Save Mode
High - 1500W (5120 BTUs), Low - 750W
Top Mounted Control Panel
Energy Save Smart Heat Control
Safety Overheat Protection
Safety Tip-Over Switch
Convenient Stay Cool Carry Handle
120V A.C., 60Hz., 12.5A
www.comfortzoneproducts.com
Save These Instructions
www.comfortzoneproducts.com
INTENDED USE:
This product is intended for indoor residential and office use
only, not for industrial or other commercial applications. Use
only with electrical wiring that is in good working order and that
meets applicable codes and ordinances. This heater must be
plugged into a 120 Volt A.C., 15 AMP (or larger) circuit. Do not
plug anything additional into the same circuit. If you have any
questions whether your wiring is adequate, consult a qualified
electrician. Risk of fire, overheating, malfunction, property
damage, injury or even death may result if not adhered to.
Use your heater only with a working smoke detector located in
the vicinity of your heater.
While using your heater, you should follow the IMPORTANT
INSTRUCTIONS listed below. As part of those instructions, we
have used the word "WARNING" to indicate the level of hazard:
WARNING indicates a hazard which, if not avoided, could result
in injury or death.
IMPORTANT INSTRUCTIONS
When using electrical appliances, basic safety precautions should always
be followed to reduce the risk of electric shock, fire, or injury to persons,
including the following precautions:
• Read all the instructions before using this heater.
• This heater is hot when in use. To avoid burns, do not let bare skin
touch hot surfaces. Use provided handle when moving this heater.
Keep combustible materials, such as furniture, pillows, bedding,
papers, clothes and curtains at least 3 feet (0.9 meters) from the front
of the heater and keep them away from the sides and rear.
• Do not use heater unattended. Use of extreme caution is necessary
when any heater is used by or near children, invalids, disabled persons
or pets.
• Do not operate the heater with a damaged power cord or after the
heater malfunctions, has been dropped or damaged in any manner.
Return heater to authorized service facility for examination, electrical or
mechanical adjustment or repair.
• Do not use heater outdoors.
• Use your heater only in dry environments. This heater is not intended
for use in a bathroom, laundry area, or similar locations, or near sinks,
washing machines, swimming pools or other sources of water. Never
locate heater where it may fall into a bathtub or other water container.
Do not use in damp environments such as flooded basements.
• Do not place the heater on a small, unlevel, uneven or any surface
which might allow heater to tip or fall.
• For proper operation, heater should be placed on a smooth, noncombustible surface. Do not place on rugs, carpet, vinyl flooring or
other plastic surfaces. Not for use outdoors or in wet areas.
• This heater is not designed as a primary heat source.
• Always plug heaters directly into a wall outlet/receptacle. Never use
with an extension cord or relocatable power tap (outlet/power strip).
Always unplug heater when not in use.
• Do not run power cord under carpeting. Do not cover cord with throw
rugs, runners or similar coverings. Arrange cord away from traffic area
where it will not be tripped over.
• To disconnect heater, turn controls off then remove plug from outlet.
• Do not insert or allow foreign objects to enter any ventilation or exhaust
opening as this may cause an electric shock or fire or damage the
heater.
• To prevent a possible fire, do not block air intakes or exhaust in any
manner. Do not use on soft surfaces like a bed, where openings may
become blocked.
• A heater has hot and arcing or sparking parts inside. Do not use it in
areas where gasoline, paint or flammable liquids are used or stored.
• Use this heater only as described in this manual. Any other use not
recommended by the manufacturer may cause fire, electric shock or
injury to persons or property.
2
EAD & SAVE THESE
R
INSTRUCTIONS
WARNING: SHOCK HAZARD
Use your heater only in dry environments. This heater is not
intended for use in a bathroom, laundry area, or similar locations,
or near sinks, washing machines, swimming pools or other
sources of water. Never locate heater where it may fall into a
bathtub or other water container. Do not use heater outdoors.
Do not use in damp environments such as flooded basements.
WARNING: HOT SURFACES
Do not touch body of heater when in use. This heater is hot when
in use, to avoid burns, do not let bare skin touch hot surfaces. If
provided, use handles when moving this heater.
WARNING: FIRE HAZARD
Heater has hot and arcing or sparking parts inside. Do not use
near combustible materials or flammable gases or sources of
heat. DO NOT USE in areas where gasoline, paint or flammable
materials are used or stored. Keep combustible materials such
as furniture, pillows, bedding, papers, clothes and curtains at
least 3 feet (0.9 meters) from the front of the heater and keep
them away from the sides and rear. To prevent a possible fire,
do not block air intakes or exhaust in any manner. Do not use on
soft surfaces, like a bed, where openings may become blocked.
Do not insert or allow foreign objects to enter any ventilation or
exhaust opening as this may cause an electric shock, fire, or
damage the heater.
WARNING: ELECTRICAL SHOCK HAZARD
Do not use with damaged cord or plug. Use with adequate
electrical system that is up to code.
The supply cord has a polarized plug. As a safety feature this
plug will fit in a polarized outlet only one way. To prevent electric
shock, match wide blade of plug to wide slot, fully insert plug. If
the plug does not fit contact a qualified electrician.
Do not operate any heater with a damaged cord or plug or after
heater malfunctions, has been dropped or damaged in any
manner. Do not operate heater with a broken heating element or
ceramic cone or any visual imperfections. For repairs covered
under warranty, see warranty statement. For all other repairs
contact Comfort Zone® Customer Service by telephone or mail
for information and assistance.
PET OWNERS NOTE:
The health of birds and some small pets are extremely
sensitive to the fumes given off during the initial use of many
appliances. Although these fumes are not harmful to humans, it
is recommended that this heater not be used around birds and
small pets during its initial use until the manufacturing corrosion
coatings burn off.
www.comfortzoneproducts.com
USAGE:
USAGE: (cont.)
HEATER OPERATION: Always operate the heater in the upright
position following all instructions and recommendations listed in
this manual. HEATER LOCATION: Place the heater in the area
of the room that is coldest. HEATER CONNECTION: Plug heater
directly into 120 Volt A.C., 60Hz wall outlet. Be sure plug fits
tightly in outlet. A loose connection may cause overheating and
damage to the plug or heater. NOTE: To prevent overloading a
circuit, do not plug the heater into a circuit that is servicing other
electrical needs.
d. Press and Hold Power Button
for 3 seconds:
i. All lights except Power Button
will turn OFF.
ii. Power Indicator light
starts blinking.
iii. Heating element turns OFF.
iv. Fan stays ON for 30 seconds and then turns OFF.
1. After fan stops, then Power Indicator light
turns
ON again.
TURNING HEATER ON: To start the heater, plug into an outlet.
The Power Indicator light will light up to indicate there is power
available. (During the heaters initial use, you may experience a
slight odor or smoking. This is the result of the heating element
lubrication “burning off.” This is normal and will go away after a
few minutes of use.)
a. While Heater is in either Low Heat or High Heat mode:
i. Press Energy Save button
:
1. Energy Save
Indicator turns ON.
2. Temperature lights turn OFF.
3. Thermostat temperature setting changes to 68°F.
4. If room temperature is BELOW 60°F, heater turns ON
in High Heat mode.
5. If room temperature is between 60°F and 68°F, heater
turns on in Low Heat mode.
6. If Room Temperature is ABOVE 68°F
a. Heater goes into Standby mode:
i. Power Indicator light
starts flashing (ON for
1.0 seconds, OFF for 0.5 seconds, repeats).
ii. Fan turns OFF.
iii. Heating element turns OFF.
b. Heater will exit Standby mode:
i. If room temperature drops BELOW Thermostat
temperature.
CONTROL PANEL
Low
Heat
High
Heat
Temperature
Indicator
Energy
Save
Indicator
Power
Indicator
Power
Mode
Thermostat
Energy Save
Mode
POWER LEVEL CONTROL PANEL: This heater has 3 heat
settings: ENERGY SAVE, HIGH, and LOW. Select the heat setting
that best meets your heating needs. The ENERGY SAVE heat
setting provides comfortable heating in most rooms, while saving
you money on energy costs. To adjust the heat settings:
HEAT SETTINGS:
a. Press Power Button
the first time:
i. Light under Low Heat
turns ON.
ii. Light under
turns ON.
iii. Heater turns on in Low Heat
mode with Thermostat
set at 80°F.
b. Press Power Button
again:
i. Light under High Heat
turns ON.
ii. Thermostat temperature light stays the way it is
– no change.
iii. Heater changes to High Heat
mode.
c. Press Power Button
again:
i. Each time the Power Button
is pressed the heater
changes back and forth between Low Heat and High
Heat modes.
ENERGY SAVE MODE:
b. Exiting Energy Save Mode:
i. If Thermostat Button
or Power Button
pressed.
1. Light under Low Heat
turns ON.
2. Light under
turns ON.
3. Heater turns ON in Low Heat mode with Thermostat
set at 80°F.
ii. If heater is turned OFF by Pressing and Holding the
Power Button
for 3 seconds.
1. All lights except Power Indicator light
turn OFF.
2. Power Indicator light
starts blinking.
3. Heating element turns OFF.
4. Fan stays ON for 30 seconds and then turns OFF.
a. After fan stops, then Power Indicator light
turns ON again.
THERMOSTAT ADJUSTMENT:
a. While heater is in either Low Heat or High Heat mode:
i. Press Thermostat Button
:
1. Temperature light cycles from
and repeats.
2. Thermostat setting adjusts to the temperature
indicated by the light.
ii. If room temperature is BELOW Thermostat setting:
1. Heater turns on at the selected heat setting.
Continued next page
3
www.comfortzoneproducts.com
USAGE: (cont.)
CARE AND MAINTENANCE: (cont.)
THERMOSTAT ADJUSTMENT: (cont.)
REPAIR: DO NOT OPERATE THE HEATER WITHOUT THE
GRILLE IN PLACE. DO NOT USE THE HEATER IF IT HAS
MALFUNCTIONED OR BECOME DAMAGED IN ANY WAY.
iii. If room temperature is ABOVE Thermostat setting:
1. Heater goes into Standby mode:
a. Power Indicator light
starts flashing (ON for
1.0 seconds, OFF for 0.5 seconds, repeats)
b. Fan stays ON for 30 seconds and then turns OFF.
c. Heating element turns OFF.
2. Exiting Standby mode:
a. If room temperature drops BELOW Thermostat
temperature.
b. If Thermostat Button
is pressed and
Thermostat setting raises to next step.
c. If Energy Save Button
is pressed and heater
enters Energy Save Mode.
d. Heater is turned OFF by Pressing and Holding
Power Button
for 3 seconds.
TURNING OFF:
Press the Power Button
for 3 seconds to turn the heater OFF
before unplugging the heater. When not in use and unplugged,
all lights will remain off. Heater should be unplugged when not
in use.
IMPORTANT SAFETY FEATURES:
The heater is equipped with an automatic overheat protection
device located inside the body of the heater. If the heater grille is
obstructed, or if the heater gets too hot for any reason, the automatic overheat protection device will turn the heater off. To reset
the heater, simply turn power off and unplug the heater for 10
minutes until it cools down and then you may plug the heater in
and restart. Be sure that the heater is on a smooth level surface
with no obstructions. The heater is also equipped with a safety
tip-over switch to turn power off to the heater when the heater
tips over. To resume heater functions simply stand heater upright.
CARE AND MAINTENANCE:
WARNING: ALWAYS UNPLUG THE CORD BEFORE MOVING
OR SERVICING. DO NOT IMMERSE HEATER IN WATER!
CLEANING: IMPORTANT! DO NOT IMMERSE HEATER IN
WATER! Clean the heater grille with the vacuum brush
attachment on your vacuum cleaner. This will remove lint and
dirt from inside the heater. DO NOT ATTEMPT TO TAKE APART
THE HEATER. DO NOT REMOVE THE HEATER GRILLE. Clean
the body of the heater with a soft cloth.
CAUTION: Do not use gasoline, benzene, paint thinner, harsh
cleaners, etc. as they will damage the heater. NEVER USE
ALCOHOL OR SOLVENTS.
STORAGE: Keep original carton for storage of the heater. Coil
and tie the power cord to avoid damage during storage.
LIMITED WARRANTY
This unit is guaranteed to the original retail purchaser against
defects in quality or workmanship for a period of one year from
the date of original purchase. If this unit fails because of a manufacturing defect within 30 days of purchase, return the unit, with
your receipt, to the retailer. After 30 days, but within the warranty
period, if the unit was purchased within the continental United
States, return it, freight prepaid, to World and Main for repair or
replacement. If the unit was purchased outside the continental
United States, return the unit to the place of purchase. This
warranty does not cover damage caused by misuse, abuse,
overheating or alteration. Repairs made by anyone other than
World and Main are not covered in this warranty. World and Main
will not be held liable for any losses due to neglectful operation. All
implied warranties, including the warranties of merchantability and
of fitness of purpose, if applicable, are hereby limited in duration
to the period of one year from the date of original retail purchase.
Some states do not allow limitations on how long an
implied warranty lasts, so the above limitations may not apply to
you. Incidental or consequential damages arising from a breach
of either express or implied warranties are hereby disclaimed and
excluded. Some states do not allow the exclusion of limitation
of incidental or consequential damages, so this limitation or
exclusion may not apply to you. Upon the expiration of this
warranty all such liability will terminate. No other warranties are
expressed or implied.
This warranty gives you specific legal rights, and you may also
have other rights which vary from state to state. No informal
dispute settlement mechanisms are available. This limited warranty
is given in lieu of all other warranties.
Manufactured for:
World and Main (Cranbury), LLC
324A Half Acre Rd.
Cranbury, NJ 08512 USA
800-221-6895
www.comfortzoneproducts.com
Rev. 04/2021
4