Troubleshooting Manual - Andrew Barton Laundry Machines

Troubleshooting Manual - Andrew Barton Laundry Machines
Troubleshooting
Home
Topload
Washers
Refer to page 5 for Model Numbers
TLW23C
www.alliancelaundry.com
Part No. 203562
August 2015
Table of
Contents
Section 1 – Safety Information ...............................................................3
Section 2 – Introduction ..........................................................................5
Model Identification ..............................................................................5
How Your Washer Works .....................................................................6
Customer Service...................................................................................8
Nameplate Location...............................................................................8
Section 3 – Troubleshooting....................................................................9
1. Production Test Summary.............................................................9
2. Keypad Combinations.................................................................10
3. Rapid Advance............................................................................11
4. Control Version Display .............................................................11
5. Low Water Level on High Fill Setting........................................11
6. No Hot Water - “Er”, “FL” .........................................................12
7. No Cold Water - “Er”, “FL” .......................................................14
8. No Warm Water - “Er”, “FL” .....................................................16
9. Slow Hot Fill or Warm Fill is Too Cold .....................................17
10. Water Fill Does Not Stop At Proper Level,
Fill Error “Er”, “FL”, Overflow Error “Er”, “OF” ....................18
11. “Er”, “PS” on the display, Pressure sensor error ........................19
12. Washer Fills, Motor Hums..........................................................21
13. Cycle Does Not Advance............................................................22
14. Motor Does Not Run - “tP”.........................................................23
15. No Agitation................................................................................25
16. Constant Agitation ......................................................................26
17. Washer Overheats, Cycles On Motor Thermal Protector,
Switch Actuator Kicks In And Out, “tP” ...................................27
18. Slow Spin Or No Spin.................................................................28
19. Constant Spin ..............................................................................30
20. Washer Stops In Cycle; Quits After A Couple Loads; Is
Intermittent - “tP”........................................................................31
21. Washer Is Locked Up Or Binding...............................................33
22. Outer Tub Does Not Empty “Er”, “dr” Drain Error,
“Er”, “Sd” Slow Drain ................................................................34
23. Excessive Vibration ....................................................................35
24. Water Leaking From Outer Tub..................................................36
Section 4 – Error Codes ........................................................................37
25. Error Codes .................................................................................37
Section 5 – Adjustments ........................................................................39
26. Leveling Legs..............................................................................39
27. Belt (Agitate And Spin) ..............................................................39
Section 6 – Test Procedures ..................................................................40
28. Motor Test Procedure..................................................................40
29. Mixing Valve Solenoid Test Procedure ......................................41
© Copyright 2015, Alliance Laundry Systems LLC
All rights reserved. No part of the contents of this book may be reproduced or transmitted in any form or by any means without
the expressed written consent of the publisher.
203562
© Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT
1
Section 7 – Cycle Sequence Charts
– Models AWNE82SN303AW01 and AWNE92SN303AW01............42
30. Normal ECO Cycle .....................................................................42
31. Delicate Cycle .............................................................................44
32. All Other Cycles..........................................................................45
Section 8 – Cycle Sequence Charts
– Models LWNE52SP543RW01, LWNE52WP543RW01 and
YWNE52SP543RW01 ...........................................................................46
33. Normal ECO Cycle .....................................................................46
34. Delicate Cycle .............................................................................47
35. All Other Cycles..........................................................................48
Section 9 – Cycle Sequence Charts
– Model LWNA52SP113TW01.............................................................49
36. Normal ECO Cycle .....................................................................49
37. Delicate Cycle .............................................................................50
38. All Other Cycles..........................................................................51
Section 10 – Cycle Sequence Charts – All Other Models...................52
39. Normal ECO Cycle .....................................................................52
40. Delicate Cycle .............................................................................53
41. All Other Cycles..........................................................................54
Section 11 – Internal Wiring of Washer Motor Switch......................55
Motor Assembly (1 Speed Motors).................................................. 55
Motor Assembly (2 Speed Motors).................................................. 56
2
© Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT
203562
Section 1
Safety Information
Throughout this manual and on machine decals, you will find precautionary statements (“CAUTION,”
“WARNING,” and “DANGER”) followed by specific instructions. These precautions are intended for the personal
safety of the operator, user, servicer and those maintaining the machine.
DANGER
Danger indicates an imminently hazardous situation that, if not avoided, will cause severe personal injury or death.
WARNING
Warning indicates a hazardous situation that, if not avoided, could cause severe personal injury or death.
CAUTION
Caution indicates a hazardous situation that, if not avoided, may cause minor or moderate personal injury or property
damage.
Additional precautionary statements (“IMPORTANT” and “NOTE”) are followed by specific instructions.
IMPORTANT
The word “IMPORTANT” is used to inform the reader of specific procedures where minor machine damage will
occur if the procedure is not followed.
NOTE
The word “NOTE” is used to communicate installation, operation, maintenance or servicing information that is
important but not hazard related.
In the interest of safety, some general precautions relating to the operation of this machine follow.
WARNING
• Failure to install, maintain and/or operate this product according to the manufacturer’s
instructions may result in conditions which can produce serious injury, death and/or
property damage.
• Do not repair or replace any part of the product or attempt any servicing unless specifically
recommended or published in this Service Manual and unless you understand and have the
skills to carry out the servicing.
• Whenever ground wires are removed during servicing, these ground wires must be
reconnected to ensure that the product is properly grounded and to reduce the risk of fire,
electric shock, serious injury or death.
W006R2
203562
© Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT
3
Safety Information
WARNING
To reduce the risk of electric shock, fire, explosion, serious injury or death:
• Disconnect electric power to the washer before servicing.
• Never start the washer with any guards/panels removed.
• Whenever ground wires are removed during servicing, these ground wires must be
reconnected to ensure that the washer is properly grounded.
W003
WARNING
Repairs that are made to your products by unqualified persons can result in hazards due to
improper assembly or adjustments subjecting you, or the inexperienced person making such
repairs, to the risk of serious injury, electrical shock, or death.
W007
WARNING
If you or an unqualified person perform service on your product, you must assume the
responsibility for any personal injury or property damage which may result. The manufacturer
will not be responsible for any injury or property damage arising from improper service and/or
service procedures.
W008
NOTE: The WARNINGS and IMPORTANT INSTRUCTIONS appearing in this manual are not meant to
cover all possible conditions and situations that may occur. Common sense, caution and care must be
exercised when installing, maintaining or operating the washer.
Always contact your dealer, distributor, service agent or the manufacturer about any problems or conditions you do
not understand.
Locating an Authorized Servicer
Alliance Laundry Systems is not responsible for personal injury or property damage resulting from improper
service. Review all service information before beginning repairs.
Warranty service must be performed by an authorized technician, using authorized factory parts. If service is
required after the warranty expires, Alliance Laundry Systems also recommends contacting an authorized
technician and using authorized factory parts.
4
© Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT
203562
Section 2
Introduction
Model Identification
Information in this manual is applicable to these washer models.
AWNE82SP113FW01
AWNE82SN303AW01
AWNE92SP113FW01
AWNE92SN303AW01
DWN432SP113CW01
FWNE52SP303ZW01
FWNE52SP303ZW14
LWN432SP113TW01
LWNA52SP113TW01
LWNE52PP113TW01
LWNE52PP113ZW01
LWNE52PP303SW01
LWNE52SP103ZW01
LWNE52SP113FQ01
203562
LWNE52SP113FW01
LWNE52SP113TW01
LWNE52SP113ZW01
LWNE52SP303AW01
LWNE52SP303BW01
LWNE52SP303EW01
LWNE52SP303NW26
LWNE52SP303SW01
LWNE52SP303UW01
LWNE52SP303ZW01
LWNE52SP543RW01
LWNE52SP543ZW01
LWNE52WP113FW01
LWNE52WP113TW01
LWNE52WP303ZW01
LWNE52WP543RW01
LWNE52WP543ZW01
YWNE52PP113CW01
YWNE52SP303EW01
YWNE52SP303UW01
YWNE52SP543RW01
YWNE52SP543ZW01
ZWN432SP113CW01
ZWNE82SP113CW01
ZWNE82SP113FW01
ZWNE92SP113FW01
© Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT
5
Introduction
How Your Washer Works
Electronic Control
Mixing
Valve
Agitator
Washtub
Outer
Tub
Transmission
Output
Board
TLW422S
Pump
Motor
6
© Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT
203562
Introduction
The cycle begins with a wash fill. The water
temperature is determined by the temperature selected
on the control. While water fills the washtub, a column
of air is trapped in a pressure bulb and hose. The air
pressure continues to increase as the washtub fills with
water until it is great enough to trip the pressure sensor
at the selected water level (load size). The pressure
sensor trip then causes the wash fill to stop and wash
agitation to begin. However, the lid must be closed for
any washer operation to occur.
The washer uses a reversing type motor, a special drive
belt and an idler assembly. The idler assembly applies
tension to the outside of the drive belt.
During agitation, the motor runs in the
counterclockwise direction. The spring tension on the
idler pulley applies the tension required to reduce the
slack on the drive belt and maintain maximum belt to
motor pulley contact. This eliminates belt slippage and
ensures an efficient wash action, even with extra large
loads.
The belt drives the transmission drive pulley in the
counterclockwise direction. The pulley drives the helix
which is splined to the input shaft of the transmission.
This causes the input shaft to turn inside of a roller
clutch which is pressed into the transmission cover.
This roller clutch acts as a bearing in the
counterclockwise direction allowing the transmission
gears to operate. The transmission’s rack and pinion
gear design produces a 210 degree agitation stroke at
the output shaft of the transmission which drives the
agitator. The brake assembly remains locked during the
agitation mode since no pressure is applied to it by the
transmission drive pulley.
As water is removed by the pump and the momentum
of the washtub increases, the idler spring tension
gradually overcomes the belt tension removing the belt
slack. This eventually increases the belt to pulley
contact until maximum spin speed is achieved.
The drive pulley turns clockwise riding up the ramps of
the helix, exerting pressure on the brake and forcing it
to release from brake pads. The helix drives the input
shaft of the transmission, and when the input shaft turns
in the clockwise direction the roller clutch locks onto
the shaft causing the entire transmission assembly to
turn. None of the gears in the transmission are
operating at this time. The hub of the washtub is splined
to the transmission tube and rotates with the
transmission assembly. The centrifugal acceleration
created by the spinning washtub causes water to be
extracted from the clothes.
Water is introduced during the first spin to “SPRAY”
the garments and remove suds from them. The initial
spin is followed by a rinse step to rinse away any
detergent residue.
During the rinse step in the Normal Eco cycle there is a
spray rinse. Water is sprayed into the washtub while it
is spinning. In all other cycles, the washer fills and then
agitates like the wash portion of the cycle.
Following the rinse step a final spin extracts the rinse
water from the clothes preparing them for the dryer.
Refer to Cycle Sequence Charts section for a detailed
breakdown of each cycle.
After the wash agitation is completed and a short pause
occurs, the control advances into the first spin. During
spin, the motor reverses turning in the clockwise
direction to spin the water out of the washtub. The
combination of water, washtub and load weight cause
the drive belt tension on the idler side of the belt to
overtake the idler spring pressure allowing the belt to
become slack on the opposite side. This reduces the
belt to pulley contact and allows slipping between the
belt and pulley.
203562
© Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT
7
Introduction
Customer Service
If literature or replacement parts are required, contact
the source from whom the machine was purchased or
contact Alliance Laundry Systems at (920) 748-3950
for the name and address of the nearest authorized parts
distributor.
For technical assistance, call (920) 748-3121.
Nameplate Location
When calling or writing about your product, be sure to
mention model and serial numbers. Model and serial
numbers are located on nameplate(s) as shown.
W429SE1B
8
© Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT
203562
Section 3
Troubleshooting
WARNING
To reduce the risk of electric shock, fire, explosion, serious injury or death:
• Disconnect electric power to the washer before servicing.
• Never start the washer with any guards/panels removed.
• Whenever ground wires are removed during servicing, these ground wires must be
reconnected to ensure that the washer is properly grounded.
W003
Re
IMPORTANT: Refer to Wiring Diagram for aid in
testing washer components.
1. Production Test Summary
To enter Production Test Mode, disconnect machine
from electrical power and reconnect. Within five
minutes press keypads 2 and 7 (Refer to Figure 1) at the
same time.
Press the Start/Pause keypad to advance through the
steps.
Test Name
Display
LEDs
Motor
Water
Valves
Audio
Tone
Auxilliary
Output
Control Type
“tL”
All Off
None
Off
Off
Off
Control Firmware Major
“XX”*
All Off
None
Off
Off
Off
Output Board
“ob”
All Off
None
Off
Off
Off
Control Level
“XX”*
All Off
None
Off
Off
Off
CCB Region Display
Cycle Confirm
“XX”*
All Off
None
Off
Off
Off
Control Dip Switches
“XX”*
All Off
None
Off
Off
Off
Keypad Test
“PX” or “XX”*
All Off
None
Off
Off
Off
Display Test
“8.8”
All On
None
Off
On
Off
High Speed Spin Test
“01”
Spin On
High Speed
Off
Off
Off
Hot Water Test
“02”
All Off
None
Hot
Off
Off
Cold Water Test
“03”
All Off
None
Cold
Off
Off
Warm Water/
Pressure Sensor Test**
“04”
All Off
None
Hot, Cold
Off
Off
High Speed Agitate
“05”
Rinse On
High Agitate
Off
Off
Off
Low Speed Agitate
“06”
Rinse On
Low Agitate
Off
Off
Off
Low Speed Spin
“07”
Spin On
Low Spin
Off
Off
Off
High Speed Spin
“08”
Spin On
High Spin
Off
Off
Off
Warm Water Test
“09”
All Off
None
Hot, Cold
Off
Off
High Speed Spin/
Tub Empty Test
“10”
Spin On
High Spin
Off
Off
Off
*“XX” displays number relating to test.
**This step will only advance automatically once specified water levels are reached.
Table 1 (Continued)
203562
© Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT
9
Troubleshooting
Table 1 (Continued)
Test Name
Display
LEDs
Motor
Water
Valves
Audio
Tone
Auxilliary
Output
Auxilliary 1
“11”
All Off
None
Off
Off
Aux 1
Auxilliary 2
“12”
All Off
None
Off
Off
Aux 2
Auxilliary 3
“13”
All Off
None
Off
Off
Aux 3
Auxilliary 4
“14”
All Off
None
Off
Off
Aux 4
Power Down
“Pd”
All Off
None
Off
Off
Off
*“XX” displays number relating to test.
**This step will only advance automatically once specified water levels are reached.
Table 1
2. Keypad Combinations
Refer to Figure 1.
Function
Keys
Entry state
Enter/Exit Software Version Display Mode
7+8
Start Mode
Enter Output Board Version Display
3+14
Start Mode
Rapid Advance
7+13
Run Mode
Enter/Exit Audit Display Mode
3+9
Start Mode
Enter Motor Thermal Protect Counter
7+9
Start Mode
Enter Production Test Mode
2+7
Start Mode under 5 min
Enter/Exit Production Test Counter
2+9
Start Mode
Toggle Keypad Acknowledgement
13+14
Start Mode
Turn On/Off Rainbow Pizzazz display
9+10
Start Mode
Enter/Exit Show Mode
3+8
Start Mode
Pressure Sensor Display
4+14
Any Mode Except
Errors
Table 2
10
© Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT
203562
Troubleshooting
3. Rapid Advance
1
5
7
9
13
18
6
8
10
14
19
2
11
23
15
20
3
16
21
4
17
22
TLW432S
TLW432S
Figure 1
For Rapid Advance press keypads 7 and 13 at the same
time to advance to the next step of the cycle. Each time
these keypads are pressed the cycle will advance to the
next step. Then press them both again to advance
through the cycle. Refer to Cycle Sequence Charts
section for each cycle step. Fill/Agitate cycle steps
count as one Rapid Advance step.
5. Low Water Level on High Fill
Setting
a. If there is an instance of a low water level on the
highest fill setting, check that the high setting
water level is between 12 and 13.5 inches.
b. If the water level is within .5 inch of this level
without clothes, it is performing as designed.
4. Control Version Display
a. To display the software version, press keypads
7 and 8 at the same time.
b. To display the output board version, press
keypads 3 and 14 at the same time.
203562
© Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT
11
Troubleshooting
6. No Hot Water - “Er”, “FL”
There is no hot water.
Is the water
supply faucet
closed?
Yes
Open faucet.
Is there
voltage at the
Hot Solenoid?
No
Check wiring
from output board
to water valve.
Yes
No
Is
Hot Solenoid
inoperative?
Yes
Is the water
supply cold?
Yes
Replace valve.
Check water heater.
No
No
Is the hot water
fill hose kinked?
Yes
Straighten or
replace hose.
Is
pressure hose
clogged or
damaged?
Yes
Remove and
clean or
replace hose.
No
Is the mixing valve
screen or screen in
outer end of fill hose
nearest water supply
faucet clogged?
Disconnect hot
Yes fill hose and
clean or
replace screen.
No
1
Is
there voltage
output from output
board to the Hot Solenoid
at “H4-8” and
“H4-1”?
No Replace
output
board.
Yes
TLW457S
12
© Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT
TLW457S
203562
Troubleshooting
No Hot Water - “Er”, “FL”
1
TLW456S
203562
© Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT
13
Troubleshooting
7. No Cold Water - “Er”, “FL”
There is no cold
water.
Is the water
supply faucet
closed?
Yes
Open faucet.
No
Is Cold
Solenoid
inoperative?
Yes
Replace valve.
No
Is the cold
water fill hose
kinked?
Yes
Straighten or
replace hose.
Is
pressure
hose clogged
or damaged?
Yes
Remove and
clean or
replace hose.
No
Is the mixing valve
screen or screen in
outer end of fill hose
nearest water supply
faucet clogged?
Disconnect
Yes cold fill hose
and clean or
replace screen.
No
1
Is
there voltage
at the output board to
the Cold Solenoid
at “H4-7” and
“H4-1”?
No
Replace
output
board.
Yes
Is
there voltage
to the Cold
Solenoid?
No
Check wiring from
output board to
water solenoid.
Yes
TLW458S
TLW458S
14
© Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT
203562
Troubleshooting
No Cold Water - “Er”, “FL”
1
TLW456S
203562
© Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT
15
Troubleshooting
8. No Warm Water - “Er”, “FL”
There is no warm
water.
Is there no
hot water?
Yes
Refer to
Paragraph 1.
No
Is there no
cold water?
Yes
Refer to Paragraph 2.
TLW328S
16
© Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT
203562
Troubleshooting
9. Slow Hot Fill or Warm Fill is Too Cold
Hot fill is slow or warm fill
is too cold.
Are fill hose
filter screens
plugged with
debris?
Yes
Clean or replace
screens.
No
Are mixing valve
screens plugged
with debris?
Yes
Clean or replace
screens.
No
Is water
pressure too
low?
Yes
Check water pressure.
Recommended water
pressure is 20 to 120 psi.
No
Unit is filling properly. Recent new mandates from the
Department of Energy (DOE) call for certain efficiencies to be
met by all washer manufacturers which require the use of a
different fill valve to meet these requirements. No
modification can be made to the washer to fill faster on these
settings.
TLW378S
TLW378S
203562
© Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT
17
Troubleshooting
10. Water Fill Does Not Stop At Proper Level, Fill Error “Er”, “FL”,
Overflow Error “Er”, “OF”
Note: To test the pressure sensor
1. Ensure sensor is connected to the front end control and there is no damage to the harness.
2. Press the 4 and 14 key pads (refer to Figure 1) at the same time while water is filling. If no change is viewed
on the display, first check pressure hose for damage. If hose is ok, replace pressure sensor.
Water fill does not
stop at proper level.
Is there
“Er”, a PS
Pressure Sensor
error?
Yes
Test
pressure
sensor.
No
Was
there a siphoning
action started in washer
causing water to be
siphoned from washer
during cycle due to end
of drain hose being
lower than cabinet top of
washer?
Is there
an “Er”, “OF”
overflow
error?
Install 562P3
Siphon
Break Kit.
No
No
Is
there an
air leak in
pressure
hose?
Yes
Replace
hose.
Does drain
hose fit tight
in standpipe
or drain?
Yes
Provide an air
gap around drain
hose and drain
receptacle.
Install No. 36878
Standpipe Adapter
(optional on some
models).
No
No
Is mixing
valve
inoperative?
Yes
Yes
Test valve and
replace if
inoperative.
Is there
water in
pressure
hose?
Yes
Blow air through
hose to remove
water or replace
hose.
No
No
Is there
broken,
loose,
shorted or
incorrect
wiring?
Yes
Refer to
appropriate
wiring diagram.
TLW425S
18
© Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT
203562
Troubleshooting
11. “Er”, “PS” on the display, Pressure sensor error
1
Is
the pressure
sensor connected
to the front
end control
at “H-5”?
No
Connect the sensor to
the front end control
Yes
Is the pressure
sensor harness
damaged?
Yes
Replace pressure sensor
No
Is the
pressure bulb,
or the sensor tube
plugged?
Yes
Clear blockage
No
Is the
pressure sensor
hose cracked?
Yes
Replace pressure sensor hose.
If the Er PS error is still displayed,
then replace the front end control.
NOTE: The pressure sensor can be tested by pressing both the
4 and 14 keypads (refer to Figure 1) at the same time while the machine is filling.
The sensor can also be tested by performing the production test.
TLW459S
203562
© Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT
19
Troubleshooting
“Er”, “PS” on the display, Pressure sensor error
1
TLW456S
20
© Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT
203562
Troubleshooting
12. Washer Fills, Motor Hums
Washer fills, motor hums
in wash portion of cycle.
Advance control
to spin. Close
lid to run
the spin step of the cycle.
Does machine
start to spin?
Does motor hum
in wash and spin
portions of cycle?
No
Yes
Yes
Unplug
machine.
Remove front
panel. Rotate main
drive pulley in both
directions. Is pulley
locked in both
directions?
Motor checks OK and
pump is clear.
Unplug
machine.
Remove front
panel. Rotate main
drive pulley in both
directions. Does
pulley freely
rotate in both
directions?
Yes
Replace
control
only.
Yes
Something
is jammed in
pump. Clean
or replace
pump.
No
Replace
motor.
No
Does pulley
rotate
clockwise?
No
Check breakes
for proper operation
Replace if needed.
Yes
Does
pulley rotate in
counter-clockwise
direction
(spin) only?
No
TLW426S
Replace transmission.
203562
© Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT
TLW426S
21
Troubleshooting
13. Cycle Does Not Advance
Cycle does not advance.
Yes
Is pause part
of normal
operation?
No
Is lid
open?
Cycle is designed to
pause during fill steps
when going from
agitate to spin and
during soak steps
(soak LED blinks).
Allow completion
of those steps. Some
cycles (delicate) have
additional pauses.
Refer to diagram for
information on time
required.
Yes
Close lid. Lid
MUST be closed
any time the
washer is set to
agitate or spin.
No
Is
Lid Switch
operative?
Is washer
siphoning
during rinse
fill?
Yes
Install siphon
break kit, Part
No. 562P3.
No
Has washer
drive motor
over loaded
and motor
thermal
overload been
tripped?
No
Replace switch.
No
Control is designed
to stop under
these conditions.
Motor thermal
proctor reset time
may vary
depending upon
Yes the reason for
washer overload,
however, it should
reset within 15
minutes. Check to
ensure washer
was not
overloaded with
clothes.
Yes
Washer
will not fill?
Cycle pauses
until pressure
switch is
satisfied.
Yes
Is circuit breaker
to washer tripped,
disconnecting
power to washer?
Yes
Reset circuit
breaker.
No
No
Is there broken,
loose or incorrect
wiring?
Yes
Refer to
appropriate
wiring diagram.
Washer
will not fill?
Yes
No
Control is designed to
pause when going
from spin into rinse
to allow the washtub
to stop spinning
before filling. Make
sure cycle has
advanced into fill
portion of rinse
cycle.
TLW460S
TLW460S
22
© Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT
203562
Troubleshooting
14. Motor Does Not Run - “tP”
Motor does not run.
Is electrical
power off, fuse
blown or power
cord not
plugged in?
Check laundry
room for blown or
loose fuse(s) or
Yes open circuit
breakers.
(Washer itself
does not have an
electrical fuse.)
No
Is lid open or
lid switch
inoperative?
Yes
Close lid or
test switch and
replace if
inoperative.
Is motor dead,
won't run?
Refer to Test
Procedures
section to
check switch
and windings.
Yes
No
1
Has
motor overload
protector cycled?
Test for continuity
at motor pins
4 and 8.
Wait two or three
minutes for overload
protector to reset. If
protector cycles
repeatedly, refer to
Paragraph 9.
Yes
No
No
Electronic
control. Test
the output board
for voltage to
the motor.
No
Replace
output
board.
Is there a bind in
upper or lower
motor bearing?
Remove belt and
determine if
motor shaft will
spin. Replace
motor if shaft is
locked up.
Yes
No
Yes
Is control
improperly
set?
Yes
Reset control or
try another
cycle.
Is there a
bind in
pump?
Yes
Replace pump.
No
No
Are motor
starting
functions
inoperative; no
start or motor
hums only?
No
Yes
Refer to Test
Procedures
section to check
start switch and
start windings.
Is there
broken,
loose or
incorrect
wiring?
Refer to
appropriate
wiring diagram.
Yes
No
Is power
cord
miswired?
Yes
Refer to
appropriate wiring
diagram for
correct wiring.
TLW461S
TLW461S
203562
© Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT
23
Troubleshooting
Motor Does Not Run - “tP”
1
TLW456S
24
© Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT
203562
Troubleshooting
15. No Agitation
NOTE: Use the production test mode to help
diagnose this issue. Refer to Production Test
Summary paragraph.
No agitation.
Are pauses
part of
normal cycle?
Yes
Control is
designed to
pause (SOAK)
during
DELICATE
cycle. Allow
completion of
SOAK period.
No
Motor
won't run?
Yes
Refer to Test
Procedures section
to check switch
and windings.
No
No delicate
cycle
agitate?
Yes
Refer to Test
Procedures
section to check
low speed switch
and windings.
Is drive
belt
broken or
loose?
Yes
Replace belt.
No
Is
transmission
assembly
inoperative?
Yes
Repair or
replace
transmission
assembly.
No
Has drive
motor
overload
protector
cycled?
Yes
Wait two or three
minutes for
overload protector
to reset. If
protector cycles
repeatedly, refer
to Paragraph 9.
No
No
Is there
broken, loose
or incorrect
wiring?
Yes
Refer to
appropriate
wiring diagram.
Is there a
bind in
pump?
Yes
Replace pump.
No
No
Is lid open
or lid switch
inoperative?
Yes
Close lid or test
switch and
replace if
inoperative.
TLW462S
203562
© Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT
25
Troubleshooting
16. Constant Agitation
Constant agitation.
Is
output control
board
inoperative?
Yes
Test control
and replace if
inoperative.
No
Is there
shorted or
incorrect
wiring?
Yes
Refer to appropriate
wiring diagram.
No
Is transmission
assembly
inoperative?
Yes
Repair or
replace
transmission
assembly.
TLW450S
TLW450S
26
© Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT
203562
Troubleshooting
17. Washer Overheats, Cycles On Motor Thermal Protector, Switch Actuator
Kicks In And Out, “tP”
Washer is locked up or binding.
Is there
excessive
belt tension?
Yes
Replace belt
and/or idler
spring.
No
Is there a bind
in upper or
lower bearing?
Are brake
pads
binding?
Yes
Yes
Free binding
pads or
replace pads.
Replace bearing.
No
No
Is there a
bind in water
pump?
Is voltage
incorrect?
Yes
Yes
Replace pump.
Contact local
utility company
or have a
qualified
electrician
check power
supply.
No
Is there a
bind in
transmission?
Yes
Repair or replace
transmission.
No
TLW338S
203562
© Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT
27
Troubleshooting
18. Slow Spin Or No Spin
NOTE: Use the production test mode to help
diagnose this issue. Refer to Production Test
Summary paragraph.
Slow spin or no spin.
Is
output control board
inoperative?
Yes
Test for
continuity
through control
(refer to wiring
diagram) and
replace if
inoperative.
No
Is lid open
or lid switch
inoperative?
Yes
Close lid or test
switch and
replace if
inoperative.
Has drive
motor overload
protector cycled?
Test for continuity
at motor pins
4 to 8.
Yes
Yes
Wait two or three
minutes for
overload protector
to reset. If
protector cycles
repeatedly, refer
to Paragraph 9.
No
Is
there no
clearance
between brake
pads and
discs?
No
Is there a
bind in
pump?
1
Yes
Replace pads
and brake
assembly.
Yes
Refer to
appropriate
wiring diagram.
Replace pump.
No
No
Is drive
belt
broken or
loose?
Is there
broken, loose
or incorrect
wiring?
Yes
Replace belt.
No
No
Motor
won't run?
Yes
Refer to Test
Procedures
section to
check switch
and windings.
Is there oil
on belt?
Yes
Replace belt.
No
TLW463S
28
© Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT
203562
Troubleshooting
Slow Spin Or No Spin
1
TLW456S
203562
© Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT
29
Troubleshooting
19. Constant Spin
NOTE: Use the production test mode to help
diagnose this issue. Refer to Production Test
Summary paragraph.
Constant spin.
Is lid switch
inoperative?
Washtub does
not stop spinning
within seven
seconds after lid
is opened.
Yes
Yes
Replace lid
switch.
Replace brake
pads and brake
assembly.
No
Is there
excessive wear
on brake pads
or missing
brake pads?
Yes
Replace brake
pads and brake
assembly.
No
Is there
shorted or
incorrect
wiring?
Yes
Refer to appropriate
wiring diagram.
No
TLW464S
30
© Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT
TLW464S
203562
Troubleshooting
20. Washer Stops In Cycle; Quits After A Couple Loads; Is Intermittent - “tP”
Washer stops in cycle, quits
after a couple loads or is
intermittent.
1
Is belt tacky,
not allowing
proper slip?
Yes
Check belt and
replace if
defective.
No
Wait two or three
minutes for
Yes overload protector
to reset. If
protector cycles
repeatedly, refer
to Paragraph 8.
Has
motor overload
protector cycled?
Test for continuity
at motor pins
4 to 8.
No
Is belt tension
too great, not
allowing
proper slip?
Yes
Make sure idler
spring is
properly
connected.
Are motor
switch
functions
inoperative?
No
Is control
inoperative?
Yes
Test control
and replace if
inoperative.
No
Is there
broken, loose
or incorrect
wiring?
Yes
Refer to
appropriate wiring
diagram.
Yes
Refer to Motor
Test Procedure
section to check
switch
functions.
No
Has brake,
transmission
or motor
locked up and
will not turn?
Yes
Check that all
these
components
are able to
move freely.
No
TLW465S
203562
© Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT
31
Troubleshooting
Washer Stops In Cycle; Quits After A Couple Loads; Is Intermittent - “tP”
1
TLW456S
32
© Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT
203562
Troubleshooting
21. Washer Is Locked Up Or Binding
Washer is locked up or binding.
Is there
excessive
belt tension?
Yes
Replace belt
and/or idler
spring.
No
Is there a bind
in upper or
lower bearing?
Are brake
pads
binding?
Yes
Yes
Free binding
pads or
replace pads.
Replace bearing.
No
No
Is there a
bind in water
pump?
Is voltage
incorrect?
Yes
Yes
Replace pump.
Contact local
utility company
or have a
qualified
electrician
check power
supply.
No
Is there a
bind in
transmission?
Yes
Repair or replace
transmission.
No
TLW338S
203562
© Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT
33
Troubleshooting
22. Outer Tub Does Not Empty “Er”, “dr” Drain Error, “Er”, “Sd” Slow Drain
Outer tub does
not empty.
Is drain hose
kinked?
Yes
Straighten hose.
No
Is drain hose out
of hose retainer
clip in back of
cabinet.
Yes
Remove washer
front panel and
install drain hose
into hose retainer
clip in back of
cabinet.
No
Is water pump
inoperative?
Yes
Replace pump.
No
Is there an
obstruction
in outer tub
outlet hose?
Yes
Remove obstruction.
TLW339S
TLW339S
34
© Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT
203562
Troubleshooting
23. Excessive Vibration
Excessive vibration.
Is there an
unbalanced
load in tub?
Yes
Stop washer,
redistribute
load, then
restart washer.
No
Is there a
broken or
disconnected
centering
spring(s)?
Yes
Connect or
replace centering
spring(s).
Yes
Yes
Replace base
assembly.
No
Is there
lubricant on
pivot dome
and/or base
friction ring?
No
Is washer
unleveled?
Is base
damaged
(washer was
dropped)?
Yes
Remove
lubricant or
replace
parts.
Adjust leveling
legs.
No
No
Is washer
installed on
weak, "spongy",
carpeted or
built-up floor?
Relocate washer or
Yes support floor to
eliminate weak or
"spongy" condition.
Is partial
liquid filled
balance ring
leaking?
Yes
Replace
balance ring.
No
No
Are cabinet
screws
incorrect or
loose?
Is friction
ring
broken?
Yes
Yes
Replace
friction ring.
Replace with
correct screws
or tighten.
No
TLW357S
203562
© Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT
35
Troubleshooting
24. Water Leaking From Outer Tub
Water leaking from
outer tub.
Is water seal
in outer tub
leaking?
Yes
Replace hub
and seal kit
assembly.
Is there an
obstruction in
drain causing
water to come
over top of outer
tub cover?
No
Is there a
hole in outer
tub?
Yes
Yes
Remove
obstruction.
Replace outer
tub.
No
No
Is pressure
hose or
accumulator
leaking?
Yes
Replace
pressure hose
and/or
accumulator.
Is tub-topump hose
leaking at
clamp?
Yes
Tighten clamp.
No
Is outer tub
cover
gasket
leaking?
Yes
Replace gasket.
No
TLW341S
36
© Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT
203562
Section 4
Error Codes
WARNING
To reduce the risk of electric shock, fire, explosion, serious injury or death:
• Disconnect electric power to the washer before servicing.
• Never start the washer with any guards/panels removed.
• Whenever ground wires are removed during servicing, these ground wires must be
reconnected to ensure that the washer is properly grounded.
W003
25. Error Codes
Error Code
Possible Causes
“Er”, “dS”: Voltage
configuration error
“Er”, “dr”: Drain Error,
control sensed water in the tub
at the end of the cycle
Corrective Action
The dipswitch setting must be corrected
The control has the incorrect voltage
dipswitch setting.
There is a disconnect power fail signal
at H2 connection on output control
board.
To clear this error the machine must be
powered down. Reset dipswitch to the correct
voltage. Correct wiring issues.
Restriction in the tub to pump hose,
drain hose blockage in the pump
Clear restriction from hoses
Replace the pump
To clear this error the machine must be
powered down.
“Er”, “FL”: Fill Error, the
desired fill level was not
reached within 30 minutes
Water supply faucet closed
Kinked or twisted fill hoses
Filter screens plugged
No voltage from output board to the
water valve (refer to appropriate
schematic)
Low water pressure
Open Faucet
Straighten fill hoses
Clean or replace filter screens
Check for voltage (refer to serial plate) from
the output board to the water valves, and if
voltage is present at output board, then check
for voltage (refer to serial plate) at the water
valve. If there is voltage (refer to serial plate) at
the water valve, then replace the mixing valve.
Correct water pressure to 20-120 psi
(138-827 kPa).
To clear this error the machine must be
powered down.
“Er”, “oF”: Overflow error, the
control was not able to lower the
water level within 5 minutes.
Leaky water valve
Possible Blockage in the pressure hose
Possible air leak in the pressure hose
Check the inlet valve
Clear blockage in pressure hose
Replace Hose if leak is found
To clear this error the machine must be
powered down.
“Er”, “PS”: The control did not
detect a valid water level input
from the pressure sensor for 30
seconds
203562
The sensor harness is not connected to
the front end control
The sensor harness is damaged, or has a
break in the wire.
The pressure tube, or hose has a
blockage
Ensure that the sensor harness is plugged into
the front end control
Replace the sensor if the harness is damaged
Clear any blockage to the pressure tube or bulb
To clear this error the machine must be
powered down.
© Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT
37
Error Codes
Error Code
Possible Causes
“tP”: The thermal protection on
the motor is open
Machine is possibly overloaded
The brakes not functioning properly
Transmission not functioning properly
Corrective Action
Properly load the machine
Check the function of the brakes
Check the function of the transmission
To clear this error wait for “tP” to clear. The
control will then prompt user to press Start.
“Er” and “Co”: SCI Comm
Error
Error in the communication between the
front end control and the output board.
There is a break or disconnect in the
main harness to the two controls.
Check for any burnt pins in the connectors or
any disconnections in the harness.
To clear this error the machine must be
powered down.
“Er” and “LE”: Water Leak
Detection Error
Water level is dropping during the leak
detection step, if enabled.
Check mixing valve for leaks.
“Er” and “Sd”: Slow Drain
Detection Error
The machine is taking longer to drain
than a preset time, if enabled.
Check the tub and drain for leaks.
“Er” and “nr”: Drive Not
Ready Error
Output board is not ready within one
minute.
Replace the output board.
To clear this error the machine must be
powered down.
“Ed” and “XX”: Output Board
Error
Error received from the output board.
Inspecting wire harnesses to output board.
Replace output board if wiring is not damaged.
To clear this error the machine must be
powered down.
“Er” and “bS”: Board Shorted
Error
Output board enable relay is shorted.
Replace the output board.
To clear this error the machine must be
powered down.
“PF”: Delay Start Power Fail
Error
Machine experienced a long power fail
or has been unplugged during Delay
Start Mode.
No service should be needed.
Press Power/cancel to continue normal
operation.
38
© Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT
203562
Section 5
Adjustments
WARNING
To reduce the risk of electric shock, fire, explosion, serious injury or death:
• Disconnect electric power to the washer before servicing.
• Never start the washer with any guards/panels removed.
• Whenever ground wires are removed during servicing, these ground wires must be
reconnected to ensure that the washer is properly grounded.
W003
26. Leveling Legs
Refer to Figure 2.
a. Place rubber feet on all four leveling legs.
b. Place washer in position on a clean, dry, and
reasonably firm floor.
c. Loosen locknuts and adjust two front leveling
legs. Once adjusted, tilt washer forward on
front legs and lower back down into position to
set the rear self-leveling legs.
d. Washer must not rock. After washer is at
desired height, tighten locknuts securely
against bottom of washer base. If these locknuts
are not tight, washer will not remain stationary
during operation.
NOTE: Improper installation, installation on
carpet or flexing of a weak floor will cause
excessive vibration.
IMPORTANT: Do not slide washer across floor
once leveling legs have been extended, as legs and
base could become damaged.
27. Belt (Agitate And Spin)
No belt adjustment is required.
Level
Washer
Base
Locknut
Rubber
Foot
Leveling
Leg
W456SE3A
Figure 2
203562
© Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT
39
Section 6
Test Procedures
WARNING
To reduce the risk of electric shock, fire, explosion, serious injury or death:
• Disconnect electric power to the washer before servicing.
• Never start the washer with any guards/panels removed.
• Whenever ground wires are removed during servicing, these ground wires must be
reconnected to ensure that the washer is properly grounded.
W003
28. Motor Test Procedure
IMPORTANT: Disconnect base wire harness plug from motor.
WARNING
Disconnect electric power to washer before performing the following steps:
W188
Motor test procedures using an Ohm meter.
NOTE: Resistance readings slightly out of given ranges may be due to meter conditions. These readings DO
NOT necessarily indicate motor failure.
Meter Connections
1.
2.
3.
4.
5.
6.
7.
Ground to Each Other Terminal
White to Yellow
Red to Brown
Blue to White
Reading
Should Be
Open
Closed
2-8 Ohms
1-2 Ohms
Violet to White (2-speed motor)
“R” to Red
“P” to Blue (2-speed motor)
2.5 Ohms
(Approximate)
Closed
Closed
If Not
Terminal shorted to ground.
Open thermal overload.
Start winding open or resistance too high or too
low.
High speed winding (4 pole) open or resistance
too high or too low.
Low winding opening; High speed winding open;
or resistance too high or too low.
Open start (auxiliary) switch.
Open start switch 4 pole winding.
NOTE: Steps 8, 9 and 10 are with motor centrifugal mechanism in the run position.
8.
9.
10.
40
“R” to Red
“P” to Blue (2-speed motor)
“P” to Blue (2-speed motor)
Open
3 Ohms
(approximate)
Closed
Start auxiliary switch.
Refer to Blue to White and Violet to White.
Open low (6 pole) winding run switch.
© Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT
203562
Test Procedures
WARNING
To reduce the risk of electric shock, fire, explosion, serious injury or death:
• Disconnect electric power to the washer before servicing.
• Never start the washer with any guards/panels removed.
• Whenever ground wires are removed during servicing, these ground wires must be
reconnected to ensure that the washer is properly grounded.
W003
29. Mixing Valve Solenoid Test Procedure
Mixing valve test procedures using an Ohm meter.
NOTE: Resistance readings slightly out of given ranges may be due to meter conditions. These readings DO
NOT necessarily indicate mixing valve failure.
120 Volt coils
240 Volt coils
203562
900 - 1100 Ohms
3200 - 4000 Ohms
© Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT
41
Section 7
Cycle Sequence Charts – Models
AWNE82SN303AW01 and
AWNE92SN303AW01
30. Normal ECO Cycle
Stage
Soak
(Select Models)
Prewash
Wash
Step
Fill
Agitate
Soak
Drain
Spin
Fill
Agitate
Pause
Drain
Spin
Fill
Low Spin and Spray
Agitate
Soak
Agitate
Soak
Agitate
Soak
Agitate
Rinse**
Second Rinse
Soak
Drain
Spin
Spray
Spin
Pause
Spin
Spray
Spin
Spray
Spin
Pause
Fill
Agitate
Pause
Drain
Spin
Time
4:00
3:00
27:00
2:00
3:00
4:00
6:00
0:10
2:00
3:00
4:00
16:00
14:00
12:00**
10:00
30:00
16:00
14:00
12:00**
10:00
30:00
16:00
14:00
12:00**
10:00
30:00
16:00
14:00
12:00**
10:00
10:00
2:00
1:00
0:46
2:45
0:10
0:05
0:46
1:00
0:46
1:00
0:10
4:00
3:00
0:10
2:00
3:00
Motor
Off
L
Off
Off
H
Off
H
Off
Off
H
Off
L
H
H
H
H
Off
H
H
H
H
Off
H
H
H
H
Off
H
H
H
H
Off
Off
L
L
L
OFF
L
L
L
L
L
OFF
Off
H
Off
Off
H
Water Valve Temperature
H,W,C*,TC
H,W,C*,TC
H,W,C*,TC
TC
TC
TC
TC
* Available on Select Models
** Default
*** Rinse will become a full tub rinse if either Second Rinse or Third Rinse is selected
Continued
42
© Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT
203562
Cycle Sequence Charts – Models AWNE82SN303AW01 and AWNE92SN303AW01
Stage
Third Rinse
(Select Models)
Step
Fill
Agitate
Pause
Drain
Spin
Fill
Agitate
Pause
Drain
Spin
Spin
Continued
Time
4:00
3:00
0:10
2:00
3:00
4:00
3:00
0:10
2:00
3:00
7:00
2:50:00
Final Spin
Default Time
* Available on Select Models
** Default
*** Rinse will become a full tub rinse if either Second Rinse or Third Rinse is selected
203562
Motor
Off
H
Off
Off
H
Off
H
Off
Off
H
H
© Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT
Water Valve Temperature
TC
TC
43
Cycle Sequence Charts – Models AWNE82SN303AW01 and AWNE92SN303AW01
31. Delicate Cycle
Stage
Step
Time
Motor
Soak
(Select Models)
Fill
Agitate
Soak
Drain
Spin
Fill
Agitate
Pause
Drain
Spin
Fill
Agitate
4:00
3:00
27:00
2:00
3:00
4:00
6:00
0:10
2:00
3:00
4:00
0:40
0:30
0:20**
0:10
3:20
2:20
1:20**
0:50
0:40
0:30
0:20**
0:10
3:20
2:20
1:20**
0:50
0:40
0:30
0:20**
0:10
3:20
2:20
1:20**
0:50
2:00
1:00
0:50
2:45
4:00
3:00
0:10
2:00
3:00
4:00
3:00
0:10
2:00
3:00
4:00
3:00
0:10
2:00
3:00
4:00
3:00
0:10
2:00
3:00
5:00
32:00
Off
L
Off
Off
L
Off
L
Off
Off
L
Off
L
L
L
L
Off
L
L
L
L
L
L
L
Off
L
L
L
L
L
L
L
Off
L
L
L
Off
L
L
L
Off
L
Off
Off
L
Off
L
Off
Off
L
Off
L
Off
Off
L
Off
L
Off
Off
L
L
Prewash
Wash
Soak
Agitate
Soak
Agitate
Soak
Rinse
Second Rinse
Third Rinse
(Select Models)
Final Spin
Default Time
Drain
Spin
Spray
Spin
Fill
Agitate
Pause
Drain
Spin
Fill
Agitate
Pause
Drain
Spin
Fill
Agitate
Pause
Drain
Spin
Fill
Agitate
Pause
Drain
Spin
Spin
Water Valve
Temperature
H,W,C*,TC
H,W,C*,TC
H,W,C*,TC
TC
TC
TC
TC
TC
* Available on Select Models
** Default
44
© Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT
203562
203562
© Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT
Time
4:00
3:00
27:00
2:00
3:00
4:00
6:00
0:10
2:00
3:00
4:00
0:10
2:00
1:00
0:50
2:45
4:00
3:00
0:10
2:00
3:00
4:00
3:00
0:10
2:00
3:00
4:00
3:00
0:10
2:00
3:00
4:00
3:00
0:10
2:00
3:00
5:00
Step
Fill
Agitate
Soak
Drain
Spin
Fill
Agitate
Pause
Drain
Spin
Fill
Agitate
Pause
Drain
Spin
Spray
Spin
Fill
Agitate
Pause
Drain
Spin
Fill
Agitate
Pause
Drain
Spin
Fill
Agitate
Pause
Drain
Spin
Fill
Agitate
Pause
Drain
Spin
Spin
Third Rinse
(Select Models)
Final
*Default
* Available on Select Models
** Default
Second Rinse
Rinse
Wash
Prewash
Soak
(Select Models)
Stage
Heavy Duty
Time
Motor
Off
L
Off
Off
H
Off
H
Off
Off
H
Off
11:00
H
H
9:00
H
7:00**
H
5:00
Off
Off
L
L
L
Off
H
Off
Off
H
Off
H
Off
Off
H
Off
H
Off
Off
H
Off
H
Off
Off
H
H
35
Whites
(Select Models)
Time
Motor
Off
L
Off
Off
H
Off
H
Off
Off
H
Off
13:00
H
11:00
H
9:00**
H
7:00
H
Off
Off
L
L
L
Off
H
Off
Off
H
Off
H
Off
Off
H
Off
H
Off
Off
H
Off
H
Off
Off
H
H
37
Perm Press
Time
Off
L
Off
Off
L
Off
H
Off
Off
L
Off
8:00
H
6:00
H
5:00**
H
4:00
H
Off
Off
L
L
L
Off
H
Off
Off
L
Off
H
Off
Off
L
Off
H
Off
Off
L
Off
H
Off
Off
L
L
33
Quick Wash
(Select Models)
Time
Motor
Off
L
Off
Off
H
Off
H
Off
Off
H
Off
6:00
H
5:00
H
4:00**
H
3:00
H
Off
Off
L
L
L
Off
H
Off
Off
H
Off
H
Off
Off
H
Off
H
Off
Off
H
Off
H
Off
Off
H
H
32
Bulky
(Select Models)
Time
Off
L
Off
Off
H
Off
L
Off
Off
H
Off
13:00
L
11:00
L
9:00**
L
7:00
L
Off
Off
L
L
L
Off
L
Off
Off
H
Off
L
Off
Off
H
Off
L
Off
Off
H
Off
L
Off
Off
H
H
37
TC
TC
TC
TC
H,W,C*,TC
H,W,C*,TC
Water Valves
Temp
H,W,C*,TC
Cycle Sequence Charts – Models AWNE82SN303AW01 and AWNE92SN303AW01
32. All Other Cycles
45
Section 8
Cycle Sequence Charts – Models
LWNE52SP543RW01, LWNE52WP543RW01
and YWNE52SP543RW01
33. Normal ECO Cycle
Stage
Step
Time
Motor
Prewash
Fill
Agitate
Pause
Spin
Fill
Agitate
4:00
6:00
0:10
3:00
4:00
13:00
12:00
11:00*
3:00
25:00
13:00
12:00
11:00*
3:00
25:00
13:00
12:00
11:00*
3:00
0:10
1:00
0:50
2:45
4:00
3:00
0:10
3:00
4:00
3:00
0:10
3:00
7:00
1:49:00
Off
H
Off
H
Off
H
H
H
H
Off
H
H
H
H
Off
H
H
H
H
Off
L
L
L
Off
H
Off
H
Off
H
Off
H
H
Wash
Soak
Agitate
Soak
Agitate
Rinse**
Second Rinse
Final Spin
Default Time
Pause
Spin
Spray
Spin
Fill
Agitate
Pause
Spin
Fill
Agitate
Pause
Spin
Spin
Water Valve
Temperature
H,W,TC
H,W,TC
TC
TC
TC
* Default
** Rinse will become a full tub rinse if Second Rinse is selected
46
© Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT
203562
Cycle Sequence Charts – Models LWNE52SP543RW01, LWNE52WP543RW01 and YWNE52SP543RW01
34. Delicate Cycle
Water Valve
Temperature
Stage
Step
Time
Motor
Prewash
Fill
Agitate
Pause
Spin
4:00
6:00
0:10
3:00
Off
L
Off
L
H,W,TC
Wash
Fill
Agitate
Off
L
L
L
L
Off
L
L
L
L
L
L
L
Off
L
L
L
L
L
L
L
Off
L
L
L
L
L
L
H,W,TC
Spin
Spray
Spin
4:00
0:40
0:30
0:20*
0:10
3:20
2:20
1:20*
0:50
0:40
0:30
0:20*
0:10
3:20
2:20
1:20*
0:50
0:40
0:30
0:20*
0:10
3:20
2:20
1:20*
0:50
1:00
0:50
2:45
Rinse
Fill
Agitate
Pause
Spin
4:00
3:00
0:10
3:00
Off
L
Off
L
TC
Second Rinse
Fill
Agitate
Pause
Spin
Spin
4:00
3:00
0:10
3:00
5:00
28:45
Off
L
Off
L
L
TC
Soak
Agitate
Soak
Agitate
Soak
Final Spin
Default Time
TC
*Default
203562
© Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT
47
Cycle Sequence Charts – Models LWNE52SP543RW01, LWNE52WP543RW01 and YWNE52SP543RW01
35. All Other Cycles
Stage
Prewash
Wash
Rinse
Second Rinse
Final
*Default
* Default
48
Step
Fill
Agitate
Pause
Spin
Fill
Agitate
Time
4:00
6:00
0:10
3:00
4:00
Pause
Spin
Spray
Spin
Fill
Agitate
Pause
Spin
Fill
Agitate
Pause
Spin
Spin
0:10
1:00
0:50
2:45
4:00
3:00
0:10
3:00
4:00
3:00
0:10
3:00
5:00
Heavy Duty
Time
Motor
Off
H
Off
H
Off
11:00
H
9:00
H
7:00*
H
5:00
H
Off
L
L
L
Off
H
Off
H
Off
H
Off
H
H
31
Perm Press
Time
8:00
6:00
5:00*
4:00
Off
H
Off
L
Off
H
H
H
H
Off
L
L
L
Off
H
Off
L
Off
H
Off
L
L
Water Valves
Temp
H,W,TC
H,W,TC
TC
TC
29
© Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT
203562
Section 9
Cycle Sequence Charts – Model
LWNA52SP113TW01
36. Normal ECO Cycle
Stage
Step
Time
Motor
Water Valve Temperature
Prewash
Fill
Agitate
Pause
Spin
4:00
4:00
0:10
3:00
Off
H
Off
H
H,W,TC
Wash
Fill
Agitate
Off
H
H
H
H
Off
L
L
L
Off
H,W,TC
Pause
Spin
Spray
Spin
Pause
4:00
11:00
9:00
7:00*
5:00
0:10
1:00
0:44
2:45
0:10
Second Rinse
Fill
Agitate
Pause
Spin
4:00
3:00
0:10
3:00
Off
L
Off
H
TC
Final Spin
Spin
9:00
H
Default Time
TC
25:00
* Default
203562
© Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT
49
Cycle Sequence Charts – Model LWNA52SP113TW01
37. Delicate Cycle
Stage
Step
Time
Motor
Water Valve Temperature
Prewash
Fill
Agitate
Pause
Spin
4:00
6:00
0:10
3:00
Off
L
Off
L
H,W,TC
Wash
Fill
Agitate
Off
L
L
L
L
Off
L
L
L
L
L
L
L
Off
L
L
L
L
L
L
L
Off
L
L
L
L
L
L
H,W,TC
Spin
Spray
Spin
4:00
0:40
0:30
0:20*
0:10
3:20
2:20
1:20*
0:50
0:40
0:30
0:20*
0:10
3:20
2:20
1:20*
0:50
0:40
0:30
0:20*
0:10
3:20
2:20
1:20*
0:50
1:00
0:50
2:45
Rinse
Fill
Agitate
Pause
Spin
4:00
3:00
0:10
3:00
Off
L
Off
L
TC
Second Rinse
Fill
Agitate
Pause
Spin
4:00
3:00
0:10
3:00
Off
L
Off
L
TC
Final Spin
Spin
5:00
L
Soak
Agitate
Soak
Agitate
Soak
Default Time
TC
29:00
*Default
50
© Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT
203562
Cycle Sequence Charts – Model LWNA52SP113TW01
38. All Other Cycles
Stage
Prewash
Wash
Rinse
Second Rinse
Final
*Default
* Default
203562
Step
Fill
Agitate
Pause
Spin
Fill
Agitate
Time
4:00
6:00
0:10
3:00
4:00
Pause
Spin
Spray
Spin
Fill
Agitate
Pause
Spin
Fill
Agitate
Pause
Spin
Spin
0:10
1:00
0:50
2:45
4:00
3:00
0:10
3:00
4:00
3:00
0:10
3:00
5:00
Heavy Duty
Time
Motor
Off
L
Off
H
Off
11:00
L
9:00
L
7:00*
L
5:00
L
Off
L
L
L
Off
L
Off
H
Off
L
Off
H
H
31
Perm Press
Motor
Off
L
Off
L
Off
8:00
L
6:00
L
5:00*
L
4:00
L
Off
L
L
L
Off
L
Off
L
Off
L
Off
L
L
29
Time
© Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT
Water Valves
Temp
H,W,TC
H,W,TC
TC
TC
51
Section 10
Cycle Sequence Charts – All Other Models
39. Normal ECO Cycle
Stage
Step
Time
Motor
Water Valve Temperature
Soak
(Select Models)
Fill
Agitate
Soak
Spin
4:00
3:00
27:00
3:00
Off
L
Off
H
H,W,C*,TC
Prewash
Fill
Agitate
Pause
Spin
4:00
6:00
0:10
3:00
Off
H
Off
H
H,W,C*,TC
Wash
Fill
Agitate
Off
H
H
H
H
Off
L
L
L
H,W,C*,TC
Pause
Spin
Spray
Spin
4:00
11:00
9:00
7:00**
5:00
0:10
1:00
0:44
2:45
Pause
Spin
Spray
Spin
Spray
Spin
Pause
0:10
0:05
0:30
1:00
0:30
1:00
0:10
OFF
L
L
L
L
L
OFF
Second Rinse
Fill
Agitate
Pause
Spin
4:00
3:00
0:10
3:00
Off
H
Off
H
TC
Third Rinse
(Select Models)
Fill
Agitate
Pause
Spin
Fill
Agitate
Pause
Spin
4:00
3:00
0:10
3:00
4:00
3:00
0:10
3:00
Off
H
Off
H
Off
H
Off
H
TC
9:00
H
Rinse***
Final Spin
Spin
Default Time
TC
TC
TC
TC
29:00
* Available on Select Models
** Default
*** Rinse will become a full tub rinse if either Second Rinse is selected
52
© Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT
203562
Cycle Sequence Charts – All Other Models
40. Delicate Cycle
Stage
Step
Time
Motor
Water Valve Temperature
Soak
(Select Models)
Fill
Agitate
Soak
Spin
4:00
3:00
27:00
3:00
Off
L
Off
H
H,W,C,TC
Prewash
Fill
Agitate
Pause
Spin
4:00
6:00
0:10
3:00
Off
L
Off
L
H,W,C,TC
Wash
Fill
Agitate
Off
L
L
L
L
Off
L
L
L
L
L
L
L
Off
L
L
L
L
L
L
L
Off
L
L
L
L
L
L
H,W,C,TC
Spin
Spray
Spin
4:00
0:40
0:30
0:20*
0:10
3:20
2:20
1:20*
0:50
0:40
0:30
0:20*
0:10
3:20
2:20
1:20*
0:50
0:40
0:30
0:20*
0:10
3:20
2:20
1:20*
0:50
1:00
0:50
2:45
Rinse
Fill
Agitate
Pause
Spin
4:00
3:00
0:10
3:00
Off
L
Off
L
TC
Second Rinse
Fill
Agitate
Pause
Spin
4:00
3:00
0:10
3:00
Off
L
Off
L
TC
Third Rinse
(Select Models)
Fill
Agitate
Pause
Spin
Fill
Agitate
Pause
Spin
4:00
3:00
0:10
3:00
4:00
3:00
0:10
3:00
Off
L
Off
L
Off
L
Off
L
TC
Spin
5:00
L
Soak
Agitate
Soak
Agitate
Soak
Final Spin
Default Time
TC
TC
29:00
*Default
203562
© Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT
53
54
Third Rinse
(Select Models)
Final
*Default
*Default
Second Rinse
Rinse
Wash
Prewash
Soak
(Select Models)
Stage
Time
4:00
3:00
27:00
3:00
4:00
6:00
0:10
3:00
4:00
0:10
1:00
0:50
2:45
4:00
3:00
0:10
3:00
4:00
3:00
0:10
3:00
4:00
3:00
0:10
3:00
4:00
3:00
0:10
3:00
5:00
Step
Fill
Agitate
Soak
Spin
Fill
Agitate
Pause
Spin
Fill
Agitate
Pause
Spin
Spray
Spin
Fill
Agitate
Pause
Spin
Fill
Agitate
Pause
Spin
Fill
Agitate
Pause
Spin
Fill
Agitate
Pause
Spin
Spin
Heavy Duty
Time
Motor
Off
L
Off
H
Off
H
Off
H
Off
11:00
H
9:00
H
7:00*
H
5:00
H
Off
L
L
L
Off
H
Off
H
Off
H
Off
H
Off
H
Off
H
Off
H
Off
H
H
31
Whites
(Select Models)
Time
Motor
Off
L
Off
H
Off
H
Off
H
Off
13:00
H
11:00
H
9:00*
H
7:00
H
Off
L
L
L
Off
H
Off
H
Off
H
Off
H
Off
H
Off
H
Off
H
Off
H
H
33
Perm Press
Time
Motor
Off
L
Off
L
Off
H
Off
L
Off
8:00
H
6:00
H
5:00*
H
4:00
H
Off
L
L
L
Off
H
Off
L
Off
H
Off
L
Off
H
Off
L
Off
H
Off
L
L
29
Quick Wash
(Select Models)
Time
Motor
Off
L
Off
H
Off
H
Off
H
Off
6:00
H
5:00
H
4:00*
H
3:00
H
Off
L
L
L
Off
H
Off
H
Off
H
Off
H
Off
H
Off
H
Off
H
Off
H
H
28
Bulky
(Select Models)
Time
Motor
Off
L
Off
H
Off
L
Off
H
Off
13:00
L
11:00
L
9:00*
L
7:00
L
Off
L
L
L
Off
L
Off
H
Off
L
Off
H
Off
L
Off
H
Off
L
Off
H
H
33
TC
TC
TC
TC
H,W,C,TC
H,W,C,TC
Water Valves
Temp
H,W,C,TC
Cycle Sequence Charts – All Other Models
41. All Other Cycles
© Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT
203562
Section 11
Internal Wiring of Washer Motor Switch
WARNING
To reduce the risk of electric shock, fire, explosion, serious injury or death:
• Disconnect electric power to the washer before servicing.
• Never start the washer with any guards/panels removed.
• Whenever ground wires are removed during servicing, these ground wires must be
reconnected to ensure that the washer is properly grounded.
W003
R
BR
BU
P W
Y
White
Brown
Blue
Yellow
Red
RUN
BR
BU
Y
R
W
G
START
W310SE3A
RED
WHITE
N
BROW
W
YELLO
BLUE
4P M
YELLOW
OVERLOAD
PROTECTOR
AUX.
W211SE3A
MOTOR ASSEMBLY
(1 Speed Motors)
203562
© Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT
55
Internal Wiring of Washer Motor Switch
WARNING
To reduce the risk of electric shock, fire, explosion, serious injury or death:
• Disconnect electric power to the washer before servicing.
• Never start the washer with any guards/panels removed.
• Whenever ground wires are removed during servicing, these ground wires must be
reconnected to ensure that the washer is properly grounded.
W003
R
Wire
Harness
Connection
Block
BR
BU
Y
P
W
White
Blue
Brown
G
P
W
R
WHITE
RUN
W311SE3B
BR
BU
Y
START
Violet
Yellow
Red
RED
VIOLE
T
BLUE
N
BROW
W
YELLO
4P M
YELLOW
OVERLOAD
PROTECTOR
6P M
AUX.
W224SE3A
MOTOR ASSEMBLY
(2 Speed Motors)
56
© Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT
203562
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertisement