Makita | 4341FCT | Specifications | Makita 4341FCT Specifications

Jig Saw
Variable Speed
MODEL 4341FCT
DOUBLE
INSULATION
I N S T R U C T I O N
M A N U A L
WARNING:
For your personal safety, READ and UNDERSTAND before using.
SAVE THESE INSTRUCTIONS FOR FUTURE REFERENCE.
w w w. m a k i t a t o o l s. c o m
SPECIFICATIONS
Model
4341FCT
Length of stroke
Cutting capacities
26 mm (1”)
Wood
135 mm (5-5/16”)
Steel
10 mm (3/8”)
Strokes per minute
800 - 2,800/min.
Overall length
271 mm (10-11/16”)
Net weight
2.4 kg (5.3 lbs)
• Manufacturer reserves the right to change specifications without notice.
• Specifications may differ from country to country.
GENERAL SAFETY RULES
USA002-2
(For All Tools)
WARNING:
Read and understand all instructions. Failure to follow all
instructions listed below, may result in electric shock, fire and/or
serious personal injury.
SAVE THESE INSTRUCTIONS
Work Area
1. Keep your work area clean and well lit.
Cluttered benches and dark areas invite accidents.
2. Do not operate power tools in explosive
atmospheres, such as in the presence of
flammable liquids, gases, or dust. Power
tools create sparks which may ignite the dust
or fumes.
2
3. Keep bystanders, children, and visitors
away while operating a power tool. Distractions can cause you to lose control.
Electrical Safety
4. Double insulated tools are equipped with
a polarized plug (one blade is wider than
the other.) This plug will fit in a polarized
outlet only one way. If the plug does not fit
fully in the outlet, reverse the plug. If it
still does not fit, contact a qualified electrician to install a polarized outlet. Do not
change the plug in any way. Double insulation
eliminates the need for the three wire
grounded power cord and grounded power
supply system.
5. Avoid body contact with grounded surfaces such as pipes, radiators, ranges and
refrigerators. There is an increased risk of
electric shock if your body is grounded.
6. Do not expose power tools to rain or wet
conditions. Water entering a power tool will
increase the risk of electric shock.
7. Do not abuse the cord. Never use the cord
to carry the tools or pull the plug from an
outlet. Keep cord away from heat, oil,
sharp edges or moving parts. Replace
damaged cords immediately. Damaged
cords increase the risk of electric shock.
8. When operating a power tool outside, use
an outdoor extension cord marked “W-A”
or “W”. These cords are rated for outdoor
use and reduce the risk of electric shock.
Personal Safety
9. Stay alert, watch what you are doing and
use common sense when operating a
power tool. Do not use tool while tired or
under the influence of drugs, alcohol, or
medication. A moment of inattention while
operating power tools may result in serious
personal injury.
10. Dress properly. Do not wear loose clothing or jewelry. Contain long hair. Keep
your hair, clothing, and gloves away from
moving parts. Loose clothes, jewelry, or long
hair can be caught in moving parts.
11. Avoid accidental starting. Be sure switch
is off before plugging in. Carrying tools with
your finger on the switch or plugging in tools
that have the switch on invites accidents.
12. Remove adjusting keys or wrenches
before turning the tool on. A wrench or a
key that is left attached to a rotating part of
the tool may result in personal injury.
13. Do not overreach. Keep proper footing
and balance at all times. Proper footing and
balance enables better control of the tool in
unexpected situations.
14. Use safety equipment. Always wear eye
protection. Dust mask, non-skid safety
shoes, hard hat, or hearing protection must
be used for appropriate conditions. Ordinary
eye or sun glasses are NOT eye protection.
Tool Use and Care
15. Use clamps or other practical way to
secure and support the workpiece to a
stable platform. Holding the work by hand or
against your body is unstable and may lead
to loss of control.
16. Do not force tool. Use the correct tool for
your application. The correct tool will do the
job better and safer at the rate for which it is
designed.
17. Do not use tool if switch does not turn it
on or off. Any tool that cannot be controlled
with the switch is dangerous and must be
repaired.
18. Disconnect the plug from the power
source before making any adjustments,
changing accessories, or storing the tool.
Such preventive safety measures reduce the
risk of starting the tool accidentally.
19. Store idle tools out of reach of children
and other untrained persons. Tools are
dangerous in the hands of untrained users.
20. Maintain tools with care. Keep cutting
tools sharp and clean. Properly maintained
tools with sharp cutting edges are less likely
to bind and are easier to control.
21. Check for misalignment or binding of
moving parts, breakage of parts, and any
other condition that may affect the tools
operation. If damaged, have the tool serviced before using. Many accidents are
caused by poorly maintained tools.
3
22. Use only accessories that are recommended by the manufacturer for your
model. Accessories that may be suitable for
one tool, may become hazardous when used
on another tool.
SERVICE
23. Tool service must be performed only by
qualified repair personnel. Service or main-
tenance performed by unqualified personnel
could result in a risk of injury.
24. When servicing a tool, use only identical
replacement parts. Follow instructions in
the Maintenance section of this manual.
Use of unauthorized parts or failure to follow
Maintenance instructions may create a risk of
electric shock or injury.
USE PROPER EXTENSION CORD: Make sure your extension cord is in good condition.
When using an extension cord, be sure to use one heavy enough to carry the current your
product will draw. An undersized cord will cause a drop in line voltage resulting in loss of
power and overheating. Table 1 shows the correct size to use depending on cord length and
nameplate ampere rating. If in doubt, use the next heavier gage. The smaller the gage number, the heavier the cord.
Table 1: Minimum gage for cord
Volts
120 V
Ampere Rating
More Than
Not More Than
0
6
10
12
6
10
12
16
25 ft.
Total length of cord in feet
50 ft.
100 ft.
150 ft.
AWG
18
18
16
14
16
16
16
12
16
14
14
12
14
12
Not Recommended
SPECIFIC SAFETY RULES
USB065-1
DO NOT let comfort or familiarity with product (gained from
repeated use) replace strict adherence to jig saw safety rules. If
you use this tool unsafely or incorrectly, you can suffer serious
personal injury.
1. Hold tool by insulated gripping surfaces
when performing an operation where the
cutting tools may contact hidden wiring or
its own cord. Contact with a “live” wire will
make exposed metal parts of the tool “live”
and shock the operator.
2. Always use safety glasses or goggles.
Ordinary eye or sun glasses are NOT
safety glasses.
3. Avoid cutting nails. Inspect workpiece for
any nails and remove them before operation.
4. Do not cut hollow pipe.
4
5. Do not cut oversize workpiece.
6. Check for the proper clearance beyond
the workpiece before cutting so that the
blade will not strike the floor, workbench,
etc.
7. Hold the tool firmly.
8. Make sure the blade is not contacting the
workpiece before the switch is turned on.
9. Keep hands away from moving parts.
11. Always switch off and wait for the blade to
come to a complete stop before removing
the blade from the workpiece.
12. Do not touch the blade or the workpiece
immediately after operation; they may be
extremely hot and could burn your skin.
13. Some material contains chemicals which
may be toxic. Take caution to prevent
working dust inhalation and skin contact.
Follow material supplier safety data.
10. Do not leave the tool running. Operate the
tool only when hand-held.
SAVE THESE INSTRUCTIONS
WARNING:
MISUSE or failure to follow the safety rules stated in this
instruction manual may cause serious personal injury.
SYMBOLS
USD201-2
The followings show the symbols used for tool.
V ....................... volts
A ....................... amperes
Hz ..................... hertz
n ....................no load speed
˚
....................Class II Construction
.../min................revolutions or reciprocation per
minute
................ alternating current
5
FUNCTIONAL
DESCRIPTION
•
001931
1
1. Cutting action changing lever
CAUTION:
Always be sure that the tool is switched off and
unplugged before adjusting or checking function on the
tool.
Selecting the cutting action
This tool can be operated with an orbital or a straight line (up
and down) cutting action. The orbital cutting action thrusts
the blade forward on the cutting stroke and greatly increases
cutting speed.
To change the cutting action, just turn the cutting action
changing lever to the desired cutting action position. Refer to
the table below to select the cutting action.
Position
Cutting action
0
Straight line cutting action
I
Small orbit cutting action
II
Medium orbit cutting action
III
Large orbit cutting action
001932
Applications
For cutting mild steel, stainless steel and plastics.
For clean cuts in wood and plywood.
For cutting mild steel, aluminum and hard wood.
For cutting wood and plywood.
For fast cutting in aluminum and mild steel.
For fast cutting in wood and plywood.
Switch action
•
CAUTION:
Before plugging in the tool, always be sure that the tool
is switched off.
To start the tool, slide the switch lever to the “I” position. To
stop the tool, slide the switch lever to the “O” position.
1
1. Switch lever
001933
1
1. Speed adjusting dial
6
Speed adjusting dial
The tool speed can be infinitely adjusted between 800 and
2,800 strokes per minute by turning the adjusting dial. Higher
speed is obtained when the dial is turned in the direction of
number 5; lower speed is obtained when it is turned in the
direction of number 1.
Refer to the table to select the proper speed for the workpiece to be cut. However, the appropriate speed may differ
with the type or thickness of the workpiece. In general, higher
speeds will allow you to cut workpieces faster but the service
life of the blade will be reduced.
Workpiece to be cut
Wood
Mild steel
Stainless steel
Aluminum
Plastics
•
Number on adjusting dial
4-5
3-5
3-4
3-5
1-4
CAUTION:
The speed adjusting dial can be turned only as far as 5
and back to 1. Do not force it past 5 or 1, or the speed
adjusting function may no longer work.
The tools equipped with electronic function are easy to operate because of the following features.
Constant speed control
Electronic speed control for obtaining constant speed. Possible to get fine finish, because the rotating speed is kept constant even under load condition.
Soft start feature
Safety and soft start because of suppressed starting shock.
Lighting up the lamps
•
CAUTION:
Do not look in the light or see the source of light directly.
To turn on the lamp, pull the trigger. Release the trigger to
turn it off.
NOTE:
•
Use a dry cloth to wipe the dirt off the lens of lamp. Be
careful not to scratch the lens of lamp, or it may lower the
illumination.
7
ASSEMBLY
•
001934
Installing or removing saw blade
•
1
1. Tool opener
CAUTION:
Always be sure that the tool is switched off and
unplugged before carrying out any work on the tool.
CAUTION:
Always clean out all chips or foreign matter adhering to
the blade and/or blade holder. Failure to do so may
cause insufficient tightening of the blade, resulting in a
serious injury.
•
Do not touch the blade or the workpiece immediately
after operation; they may be extremely hot and could
burn your skin.
•
Tighten the saw blade securely. Failure to do so may
cause a serious injury.
•
When you remove the saw blade, be careful not to hurt
your fingers with the top of the blade or the tips of
workpiece.
To install the blade, open the tool opener to the position
shown in the figure.
001935
3
Keeping that situation, insert the saw blade into the blade
clamp as far as the two protrusions of the blade can not be
seen.
Return the tool opener to its original position.
After installing, always make sure that the blade is securely
held in place by trying to pull it out.
1
2
1. Blade clamp
2. Jig saw blade
3. Protrusions
•
001936
CAUTION:
Do not open the tool opener excessively, or it may cause
tool damage.
To remove the blade, open the tool opener to the position
shown in the figure. Pull the saw blade out toward the base.
NOTE:
•
1
1. Jig saw blade
8
Occasionally lubricate the roller.
001937
Hex wrench storage
When not in use, the hex wrench can be conveniently stored.
1
2
1. Base
2. Hex wrench
OPERATION
•
CAUTION:
Always hold the tool base flush with the workpiece.
Failure to do so may cause blade breakage, resulting in
a serious injury.
001938
Turn the tool on and wait until the blade attains full speed.
Then rest the tool base flat on the workpiece and gently
move the tool forward along the previously marked cutting
line. When cutting curves, advance the tool very slowly.
001939
Bevel cutting
1
2
1. Cutting line
2. Base
•
CAUTION:
Always be sure that the tool is switched off and
unplugged before tilting the tool base.
With the tool base tilted, you can make bevel cuts at any
angle between 0˚ and 45˚ (left or right).
001940
1
Loosen the bolt on the back of the base with the hex wrench.
Move the base so that the bolt is positioned in the center of
the bevel slot in the base.
3
2
1. Base
2. Bolt
3. Hex wrench
9
1
2
5
6
1.
2.
3.
4.
5.
6.
001941
Tilt the base until the desired bevel angle is obtained. The Vnotch of the gear housing indicates the bevel angle by graduations. Then tighten the bolt firmly to secure the base.
001942
Front flush cuts
3
4
Graduations
Bevel slot
Base
Bolt
Gear housing
V-notch
1
3
2
Loosen the bolt on the back of the tool base with the hex
wrench, then move the tool base all the way back. Then
tighten the bolt to secure the tool base.
1. Base
2. Bolt
3. Hex wrench
Cutouts
Cutouts can be made with either of two methods A or B.
001943
1
1. Starting hole
10
A) Boring a starting hole:
For internal cutouts without a lead-in cut from an edge,
pre-drill a starting hole 12 mm (1/2”) or more in diameter.
Insert the blade into this hole to start your cut.
001944
B) Plunge cutting:
You need not bore a starting hole or make a lead-in cut if
you carefully do as follows.
(1) Tilt the tool up on the front edge of the base, with
the blade point positioned just above the workpiece
surface.
(2) Apply pressure to the tool so that the front edge of
the base will not move when you switch on the tool
and gently lower the back end of the tool slowly.
(3) As the blade pierces the workpiece, slowly lower the
base of the tool down onto the workpiece surface.
(4) Complete the cut in the normal manner.
001945
Finishing edges
To trim edges or make dimensional adjustments, run the
blade lightly along the cut edges.
Metal cutting
Always use a suitable coolant (cutting oil) when cutting
metal. Failure to do so will cause significant blade wear. The
underside of the workpiece can be greased instead of using
a coolant.
001946
1
Dust extraction
The dust nozzle (optional accessory) is recommended to
perform clean cutting operations.
To attach the dust nozzle on the tool, insert the hook of dust
nozzle into the hole in the base.
2
1. Dust nozzle
2. Base
11
001947
The dust nozzle can be installed on either left or right side of
the base.
001948
Then connect a Makita vacuum cleaner to the dust nozzle.
1
2
1. Dust nozzle
2. Hose for vacuum cleaner
Rip fence set (optional accessory)
•
001949
1
1. Rip fence
001950
3
1
2
1. Bolt
2. Fence guide
3. Hex wrench
12
CAUTION:
Always be sure that the tool is switched off and
unplugged before installing or removing accessories.
1. Straight cuts
When repeatedly cutting widths of 160 mm (6-5/16”) or
less, use of the rip fence will assure fast, clean, straight
cuts. To install, insert the rip fence into the rectangular
hole on the side of the tool base with the fence guide facing down. Slide the rip fence to the desired cutting width
position, then tighten the bolt to secure it.
001951
001952
2
2. Circular cuts
When cutting circles or arcs of 170 mm (6-11/16”) or less
in radius, install the rip fence as follows.
Insert the rip fence into the rectangular hole on the side
of the tool base with the fence guide facing up. Insert the
circular guide pin through either of the two holes on the
fence guide. Screw the threaded knob onto the pin to
secure the pin.
Now slide the rip fence to the desired cutting radius, and
tighten the bolt to secure it in place. Then move the tool
base all the way forward.
NOTE:
•
3
1
Always use blades No. B-17, B-18, B-26 or B-27 when
cutting circles or arcs.
1. Fence guide
2. Threaded knob
3. Circular guide pin
001953
1
Cover plate
Use the cover plate when cutting decorative veneers, plastics, etc. It protects sensitive or delicate surfaces from damage. Fit it on the back of the tool base.
2
1. Cover plate
2. Base
001954
1
2
1. Base
2. Anti-splintering device
Anti-splintering device
For splinter-free cuts, the anti-splintering device can be used.
To install the anti-splintering device, move the tool base all
the way forward and fit it from the back of tool base. When
you use the cover plate, install the anti-splintering device
onto the cover plate.
•
CAUTION:
The anti-splintering device cannot be used when making
bevel cuts.
13
MAINTENANCE
•
CAUTION:
Always be sure that the tool is switched off and
unplugged before attempting to perform inspection or
maintenance.
To maintain product SAFETY and RELIABILITY, repairs, carbon brush inspection and replacement, any other maintenance or adjustment should be performed by Makita
Authorized or Factory Service Centers, always using Makita
replacement parts.
ACCESSORIES
•
CAUTION:
These accessories or attachments are recommended for
use with your Makita tool specified in this manual. The
use of any other accessories or attachments might
present a risk of injury to persons. Only use accessory
or attachment for its stated purpose.
If you need any assistance for more details regarding these
accessories, ask your local Makita service center.
14
•
Jig saw blade
•
Rip fence set
•
Dust nozzle
•
Cover plate
•
Anti-splintering device
•
Hex wrench
Memo
15
Memo
16
Cut
First-Class
Postage
Required
Post Office will
not deliver
without proper
postage.
Makita U.S.A., Inc.
14930 Northam Street
La Mirada, CA 90638-5753
Fold
17
MAIL THIS PORTION
Your answer to the following questions are appreciated.
1. This product was purchased from:
Home Center
3. How did you learn about this product:
Magazine
Radio
Hardware/Lumber Store
From Dealer
Exhibition
Tool Distributor
Newspaper
From Friend
Industrial Supply
Store Display
Previous Usage
Construction Supply
Catalog
Other (
Other (
)
2. Use of the product is intended for:
)
4. Most favored points are:
Construction Trade
Design
Repair Service
Industrial Maintenance
Features
Durability
Home Maintenance
Size
Power
Hobby
Price
Other (
Other (
)
)
Makita Brand
5. Any comments:
Paste
MODEL NO.
DAY
YEAR
SERIAL NO.
SEX
STATUS
INTL.
LAST NAME / COMPANY NAME
Married Single
M
F
STREET ADRESS
Paste
MONTH
Paste
Paste
Paste
Paste
DATE PURCHASED
Under 19
AREA
CODE
PHONE
20-29
30-39
Paste
AGE:
ZIP CODE
40-49
50-60
Over 60
Paste
Paste
STATE
Paste
CITY
Paste
Paste
BE SURE TO COMPLETE THE CUSTOMER’S PORTION OF THIS FORM AND RETAIN FOR YOUR RECORDS.
Please return this portion by facsimile or mail.
18
Facsimile No: (714) 522-8133
Paste
Paste
Paste
Paste
Paste
Paste
Paste
Paste
FACTORY SERVICE CENTERS
1-800-4-MAKITA
RETAIN THIS PORTION FOR YOUR RECORDS
ALABAMA
2365 Pelham Parkway
Pelham, AL 35124
(205) 620-1791
COLORADO
11839 E. 51st Ave.
Denver, CO 80239-2709
(303) 371-2850
KENTUCKY
1215 S. Hurstbourne Parkway
Louisville, KY 40222
(502) 326-3740
NEW MEXICO
5805 Menaul Blvd. NE
Albuquerque, NM 87110
(505) 881-4619
PUERTO RICO
200 Guayama St.
Hato Rey, PR 00917
(787) 250-8776
ARIZONA
3707 E. Broadway Rd., Ste. 6
Phoenix, AZ 85040
(602) 437-2850
CONNECTICUT
508 Spring St.
Windsor Locks, CT 06096
(860) 292-6405
LOUSIANA
5626 Jefferson Hwy.
Harahan, LA 70123
(504) 733-4138
NEW YORK
4917 Genessee Street
Cheektowaga, NY 14225
(716) 685-9503
TENNESSEE
4655 Nolensville Rd.
Nashville, TN 37211
(615) 331-9922
ARKANSAS
Shackleford Shopping Center
240 South Shackleford Rd.,
Ste. C
Little Rock, AR 72211
(501) 224-5733
FLORIDA
620 Douglas Ave. Suite 1302
Altamonte Springs, FL 32714
(407) 774-6000
MARYLAND
7541 - 45 Ritchie Highway
Glen Burnie, MD 21061
(410) 590-0160
CALIFORNIA
41850 Christy St.
Fremont, CA 94538-5107
(510) 657-9881
1421 N. Clovis Ave., Ste. 112
Fresno, CA 93727
(559) 252-5166
14930 Northam St.
La Mirada, CA 90638-5753
(714) 522-8088
1970 Fulton Avenue
Sacramento, CA 95825
(916) 482-5197
1440 South “E” Street
San Bernardino, CA 92408
(909) 885-1289
7674 Clairemont Mesa Blvd.
San Diego, CA 92111
(858) 278-4471
1714 E.McFadden Ave., Unit M
Santa Ana, CA 92705
(714) 667-5066
1565 Winchester B.
Campbell, CA 95008-0501
(408) 379-0377
16735 Saticoy St., Ste. 105
Van Nuys, CA 91406
(818) 782-2440
750 East Sample Road
Pompano Beach, FL 33064
(954) 781-6333
Thompson Center Waters
5501 W. Waters Ave., Ste. 406
Tampa, FL 33634
(813) 886-8292
GEORGIA
4680 River Green Parkway
Duluth, GA 30096-2566
(770) 476-8911
HAWAII
4510 Salt Lake Blvd., Suite A7
Honolulu, HI 96818
(808) 847-0038
ILLINOIS
1450 Feehanville Dr.
Mt. Prospect, IL 60056-6011
(847) 297-3100
INDIANA
8403 Michigan Road, Unit 1
Indianapolis, IN 46268
(317) 334-9980
KANSAS
8819 W. 95th St.
Overland Park, KS 66212
(913) 642-1111
MASSACHUSETTS
232 Providence Hwy.
Westwood, MA 02090
(617) 461-9754
MICHIGAN
37454 Ann Arbor Trail
Livonia, MI 48150
(313) 432-1012
131-35 31st Ave.
Flushing, NY 11354
(718) 886-0971
NORTH CAROLINA
3501-G S. Tryon St.
Charlotte, NC 28217
(704) 527-0611
OHIO
6253 E. Main St.
Columbus, OH 43213
(614) 860-0222
6379 Pearl Road
Parma Heights, OH 44130
(440) 843-7555
MINNESOTA
6427 Penn Ave. South
Richfield, MN 55423
(612) 869-5199
1617 E. Kemper Rd.
Sharonville, OH 45246
(513) 771-0788
MISSOURI
9876 Watson Road
St. Louis, MO 63126-2221
(314) 909-9889
OKLAHOMA
552 E. Memorial Road
Oklahoma City, OK 73114
(405) 752-2655
NEBRASKA
4129 S. 84th St.
Omaha, NE 68127
(402) 597-2925
OREGON
828 19th Avenue., N.W.
Portland, OR 97209
(503) 222-1823
NEVADA
3375 S. Decatur Blvd.
Suites. 22 - 24
Las Vegas, NV 89102
(702) 368-4277
PENNSYLVANIA
Springwater Plaza
364 Wilmington W. Chester
Pike
Glen Mills, PA 19342
(610) 459-4122
NEW JERSEY
251 Herrod Blvd.
Dayton, NJ 08810-1539
(609) 655-1212
6200 Babcock Blvd
Pittsburgh, PA 15237
(412) 366-6363
TEXAS
12801 Stemmons Fwy Ste. 809
Farmers Branch, TX 75234
(972) 243-1150
12701 Directors Dr.
Stafford, TX 77477-3701
(281) 565-8665
3453 IH-35 North, Ste. 101
San Antonio, TX 78219
(210) 228-0676
UTAH
145 E. 1300 S., Ste. 101
Salt Lake City, UT 84115
(801) 359-3410
VIRGINIA
5760 Northampton Blvd,. Ste.
102
Virginia Beach, VA 23455
(757) 460-0280
WASHINGTON
22220 84th Ave. So., Bldg. A
Kent, WA 98032
(253) 395-8055
WISCONSIN
Lincoln Plaza Shopping Ctr.
2245 S. 108th St. West Allis, WI
53227
(414) 541-4776
CUSTOMER’S RECORD
When you need service: Send
complete tool (prepaid) to one
of the Makita Factory Service
Centers listed, or to an Authorized
Makita Service Center. Be sure
to attach a letter to the outside of
the carton detailing the problem
with your tool.
Date Purchased
Dealer’s Name & Address
Model No.
Serial No.
19
WARNING
Some dust created by power sanding, sawing, grinding, drilling, and other
construction activities contains chemicals known to the State of California
to cause cancer, birth defects or other reproductive harm. Some examples
of these chemicals are:
• lead from lead-based paints,
• crystalline silica from bricks and cement and other masonry products, and
• arsenic and chromium from chemically-treated lumber.
Your risk from these exposures varies, depending on how often you do this
type of work. To reduce your exposure to these chemicals: work in a well
ventilated area, and work with approved safety equipment, such as those
dust masks that are specially designed to filter out microscopic particles.
MAKITA LIMITED ONE YEAR WARRANTY
Warranty Policy
Every Makita tool is thoroughly inspected and tested before leaving the factory. It is warranted to be free of
defects from workmanship and materials for the period of ONE YEAR from the date of original purchase.
Should any trouble develop during this one-year period, return the COMPLETE tool, freight prepaid, to one of
Makita's Factory or Authorized Service Centers. If inspection shows the trouble is caused by defective
workmanship or material, Makita will repair (or at our option, replace) without charge.
This Warranty does not apply where:
• repairs have been made or attempted by others:
• repairs are required because of normal wear and tear:
• the tool has been abused, misused or improperly maintained:
• alterations have been made to the tool.
IN NO EVENT SHALL MAKITA BE LIABLE FOR ANY INDIRECT, INCIDENTAL OR CONSEQUENTIAL
DAMAGES FROM THE SALE OR USE OF THE PRODUCT. THIS DISCLAIMER APPLIES BOTH DURING
AND AFTER THE TERM OF THIS WARRANTY.
MAKITA DISCLAIMS LIABILITY FOR ANY IMPLIED WARRANTIES, INCLUDING IMPLIED WARRANTIES OF
"MERCHANTABILITY" AND "FITNESS FOR A SPECIFIC PURPOSE," AFTER THE ONE-YEAR TERM OF
THIS WARRANTY.
This Warranty gives you specific legal rights, and you may also have other rights which vary form state to state.
Some states do not allow the exclusion or limitation of incidental or consequential damages, so the above
limitation or exclusion may not apply to you. Some states do not allow limitation on how long an implied
warranty lasts, so the above limitation may not apply to you.
MAKITA MANUFACTURING EUROPE LTD
ROAD 7, HORTONWOOD INDUSTRIAL ESTATE
TELFORD, SHROPSHIRE TF1 4GP, ENGLAND
884427-062
Download PDF