Quick Use Manual
This document applies to the following series of products。
HF2421
http://www.iotworkshop.com
1
Copyright © 2013 . All rights reserved
TABLE OF CONTENTS
1.
2.
3.
HF2421General Description ............................................................................................ 3
1.1. HF2421Equipment shape and interface ................................................................. 3
Serial Tool Introduce .......................................................................................................... 3
2.1. Serial Tool SecureCRT .............................................................................................. 3
2.2. Setting Serial Port Parameters ................................................................................. 4
HF2421 Device parameter configuration ..................................................................... 5
3.1. IOTService Tool Introduction .................................................................................... 5
3.2. WEB ............................................................................................................................. 5
4.
Transparent case One：W EB Configuration .............................................................. 6
5.
Transparent test case two：IOTSerivice Tool Configuration ................................ 9
6.
Web page upgrade firmware .......................................................................................... 11
Appendix 1 ................................................................................................................................... 12
HISTORY
Ed. V1.0 11-04-2018
http://www.iotworkshop.com
First Version.
2
Copyright © 2013 . All rights reserved
1. HF2421General Description
The 4G serial server HF2421 provides
RS232/RS485/RS422, Wi-Fi/Ethernet and 3G/4G.
a
protocol
conversion between
1.1. HF2421Equipment shape and interface
HF2421 Front view
HF2421 Side interface diagram
2. Serial Tool Introduce
2.1. Serial Tool SecureCRT
Download address：
http://www.hi-flying.com/download-center-1/applications-1/download-item-secur
ecrt
Unzip the folder r and open SecureCRT，
Click on the quick connect button
http://www.iotworkshop.com
3
。
，Create connection.。
Copyright © 2013 . All rights reserved
2.2. Setting Serial Port Parameters
protocol：Serial
port：The port that the computer is actually connected to (see "My Computer"
-> "Device Manager" -> "Ports (COM and LPT)", as shown。）
Baud rate：115200
Data bits：8
Parity ：None
Stop bit：1
Flow Control：None（Please remove "√" in front of RTS/CTS）
Note: The default serial port data of the HF2421 device is as shown in the above
figure. The user can modify the operating parameters of the product through the
IOTService.
This serial port software can be used to configure or transparently test the device.
http://www.iotworkshop.com
4
Copyright © 2013 . All rights reserved
3. HF2421 Device parameter configuration
There are three methods for the parameter configuration of Hanfeng industrial
control device
1, IOTService tool
2, WEB page
3, serial port Cli command. This method document does not introduce. If
you use to view the Cli commands in the user manual
3.1. IOTService Tool Introduction
IOTService software is used to configure module operating parameters and
remote management, view module status, upgrade, and other functions to
facilitate device testing.
The IOTService tool download URL is
http://www.hi-flying.com/download-center-1/applications-1/download-item-iotservice
3.2. WEB
Hanfeng Industrial Controls device also provides WEB web page configuration
parameters. the PC is connected to the product's AP or the network cable is directly
connected, enter the product default IP (10.10.100.254, default login user name and
password: admin/admin) in the browser. You can log in to configure the parameters
on the web page. Google, Firefox browser is recommended, browsers with 360 and
below IE8 are not supported
http://www.iotworkshop.com
5
Copyright © 2013 . All rights reserved
4. Transparent case One：WEB Configuration
Application Scenario HF2421 Device Passes Data Through 4G Network。The
following topology is shown。Device parameter setting requirements：the device is
connected
as
a
client
mode
to
our
Hanfeng
test
server.
Address:
nat1.iotworkshop.com, TCP port: 3006.
Step1: Plug in a SIM card that can access the Internet and connect the antenna to
the power supply. Then connect the hotspot or network cable of the PC directly to
the computer. Then you should check the IP address obtained by the PC.。
Note: The IP address obtained after the PC connects to the AP of the device is
10.10.100.xxx.
If the network cable is directly connected to the PC, there are two situations in
which the PC obtains the IP address. 1, the device wifi work mode is AP mode, the
PC got the IP address is 169.254.xxx.xxx. 2 Device wifi works In STA mode, the PC
gets the is 10.10.100.xxx
。
Step 2：Open the browser input device IP address, enter the settings page and then
check whether the device is connected to the 4G network, mainly to see if the
http://www.iotworkshop.com
6
Copyright © 2013 . All rights reserved
device has an IP address, as shown below. If the device's IP address is 0, it means
there is no network connection. Disconnect the SIM card after power off.
Note: The computer is best to open only one network card. If your computer's IP
address is 10.10.100.xxx, enter 10.10.100.254 to enter the web settings interface. If
the IP address obtained by the computer is 169.254.xxx.xxx, enter 169.254.173.207
to enter the web page setting interface. The SIM card of this device does not
support hot plugging.。
Step 3：Click on the communication settings, select the protocol type and fill in the
server address and port number and serial port number. After setting, click the
submit button.
Note: The HF2421 device has two serial ports, uart1 and uart2, which need to be set
corresponding to the serial port number on the device.。
http://www.iotworkshop.com
7
Copyright © 2013 . All rights reserved
Step 4 :After setting, restart the device as shown below.
Step 5：The PC opens the Serial SecureCRT tool, selects the corresponding port
number and baud rate, and displays the interactive window.
Step 6：Transparent transmission test.
http://www.iotworkshop.com
8
Copyright © 2013 . All rights reserved
5. Transparent test case two：IOTSerivice Tool
Configuration
The application scenario is the same as the case one.
Step 1: Insert a SIM card that can access the Internet and connect the antenna to
the power supply. Then, the PC connects the device's hotspot or network cable
directly to the PC.
Step2 :Open the IOTService tool and the device will appear as shown below.。
Step 3：Double-click the device bar to enter the device status interface and check
whether the device is connected to the 4G network. If it is connected, click the edit
button to enter the device editing interface. If the device IP address is 0, it indicates
that no 4G network is connected, power is off, and the card is inserted or removed.
Step 4: After entering the configuration interface, set the network communication
parameters. After setting, click OK, as shown in the figure below.
http://www.iotworkshop.com
9
Copyright © 2013 . All rights reserved
、
Step 5：Restart
Step 6: The PC opens the Serial SecureCRT tool for transparent data transmission
test。
http://www.iotworkshop.com
10
Copyright © 2013 . All rights reserved
6. Web page upgrade firmware
The device supports online firmware upgrades. Users can upgrade through the
web page portal. External web pages and internal web pages (suffix +hide, internal
web pages can also be used to upgrade external web pages) can be used.。
HF2421 device latest firmware address:
http://www.hi-flying.com/download-center-1/firmware-1/download-item-hf2421-f
irmware
Step1: Enter the Hanfeng official website to download the latest firmware。
Step 2:Open the browser and enter the device IP address to enter the web page
setting interface.
Step 3: Click on other to select the firmware
Step 4:After selecting the firmware, click Start. The device will restart
automatically after success.
Step 5: After the device restarts, you can enter the web page again to check the
firmware version to determine whether the firmware upgrade is successful.
http://www.iotworkshop.com
11
Copyright © 2013 . All rights reserved
Appendix 1
For more information, please visit the official website to download more
information about industrial control equipment applications.
download link:
Http://www.hi-flying.com/download-center-1/application-notes-1/download-item
-industry-products-application-manual-20180415
http://www.iotworkshop.com
12
Copyright © 2013 . All rights reserved
">
