Wisenet XRN-6410RB2 User Manual

NETWORK VIDEO RECORDER
User Manual
Wisenet NVR
Network Video Recorder
User Manual
Copyright
©2021 Hanwha Techwin Co., Ltd. All rights reserved.
Trademark
Each of trademarks herein is registered. The name of this product and other trademarks mentioned in this manual are the registered
trademark of their respective company.
Restriction
Copyright of this document is reserved. Under no circumstances, this document shall be reproduced, distributed or changed, partially
or wholly, without formal authorization.
Disclaimer
Hanwha Techwin makes the best to verify the integrity and correctness of the contents in this document, but no formal guarantee
shall be provided. Use of this document and the subsequent results shall be entirely on the user’s own responsibility. Hanwha
Techwin reserves the right to change the contents of this document without prior notice.
❖ Design and specifications are subject to change without prior notice.
You can download the latest version from the Hanwha Techwin web site. (www.hanwha-security.com)
❖ The initial administrator ID is “admin” and the password should be set when logging in for the first time.
Please change your password every three months to safely protect personal information and to prevent the damage of the
information theft.
Please, take note that it’s a user’s responsibility for the security and any other problems caused by mismanaging a password.
Hanwha Techwin Co., Ltd. is a surveillance camera manufacturer that provides video information equipment with various functions.
Users must comply with local laws when using our devices.
Users are solely responsible for any illegal use of our products.
overview
Important Safety Instructions
Standards Approvals
Read these operating instructions carefully before using the unit.
Follow all the safety instructions listed below.
Keep these operating instructions handy for future reference.
Read these instructions.
2)
Keep these instructions.
3)
Heed all warnings.
4)
Follow all instructions.
5)
Do not use this apparatus near water.
6)
Clean the contaminated area on the product surface with a soft, dry cloth or a damp cloth.
(Do not use a detergent or cosmetic products that contain alcohol, solvents or surfactants or oil constituents
as they may deform or cause damage to the product.)
7)
Do not block any ventilation openings, Install in accordance with the manufacturer's instructions.
8)
Do not install near any heat sources such as radiators, heat registers, stoves, or other apparatus (including
amplifiers) that produce heat.
9)
Do not defeat the safety purpose of the polarized or grounding- type plug. A polarized plug has two blades
with one wider than the other. A grounding type plug has two blades and a third grounding prong. The
wide blade or the third prong are provided for your safety. if the provided plug does not fit into your outlet,
consult an electrician for replacement of the obsolete outlet.
￭ Any changes or modifications in construction of this device which are not expressly approved by the party responsible for compliance could void
the user's authority to operate the equipment.
￭ This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful
interference, and (2) this device must accept any interference received, including interference that may cause undesired operation.
￭ This equipment has been tested and found to comply with the limits for a Class A digital device, pursuant to part 15 of the FCC Rules.
￭
￭
￭
￭
These limits are designed to provide reasonable protection against harmful interference when the equipment is operated in a commercial
environment.
This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instruction
manual, may cause harmful interference to radio communications. Operation of this equipment in a residential area is likely to cause harmful
interference in which case the user will be required to correct the interference at his own expense.
Reorient or relocate the receiving antenna.
Increase the separation between the equipment and receiver.
Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
Consult the dealer or an experienced radio/TV technician for help.
10) Protect the power cord from being walked on or pinched particularly at plugs, convenience receptacles, and
the point where they exit from the apparatus.
Product User Manual Description
11) Only use attachments/accessories specified by the manufacturer.
This document is a user manual for Recorder product. Before using this product, please read this document carefully in
order to use it properly.
12) Use only with the cart, stand, tripod, bracket, or table specified by the manufacturer, or sold with the
apparatus. When a cart is used, use caution when moving the cart/apparatus combination to avoid injury
from tip-over.
●
This user manual explains how to use the product based on the defaults and default screens of this product.
●
The content of this manual is subject to change depending on the product software updates and the company
policies. It is subject to partial changes without prior notification to users.
Target Audience
This user manual contains contents for Recorder users.
13) Unplug this apparatus during lightning storms or when unused for long periods of time.
14) Refer all servicing to qualified service personnel. Servicing is required when the apparatus has been
damaged in any way, such as power-supply cord or plug is damaged, liquid has been spilled or objects have
fallen into the apparatus, the apparatus has been exposed to rain or moisture, does not operate normally, or
has been dropped.
How to Use the Product
Users of this product can perform the following:
●
Monitor cameras registered to Recorder in real time
●
Search for or play videos saved in Recorder
●
Monitor text data being transmitted to the POS device connected to Recorder in real time
●
Search for text data from the POS device connected to Recorder
●
Monitor real time events that occur in Recorder, sensors, and cameras or search through logs
Before using this product, check if the latest version of this software is installed. Go to Hanwha Techwin's website (http://
www.hanwha-security.com) to check the software version and download necessary files.
English _3
• overview
1)
overview
CAUTION
●
RISK OF EXPLOSION IF BATTERY IS REPLACED BY AN INCORRECT TYPE. DISPOSE OF USED BATTERIES
ACCORDING TO THE INSTRUCTIONS.
●
Do not ingest battery, Chemical Burn Hazard.
●
This product contains a coin / button cell battery. If the coin / button cell battery is swallowed, it can cause
severe internal burns in just 2 hours and can lead to death.
●
Keep new and used batteries away from children. If the battery compartment does not close securely, stop
using the product and keep it away from children.
If you think batteries might have been swallowed or placed inside any part or the body, seek immediate
medical attention.
ATTENTION
●
IL Y A RISQUE D'EXPLOSION SI LA BATTERIE EST REMPLACÉE PAR UNE BATTERIE DE TYPE INCORRECT.
METTRE AU REBUT LES BATTERIES USAGÉES CONFORMÉMENT AUX INSTRUCTIONS.
●
Ne pas ingérer la pile, risque de brûlure chimique.
●
Ce produit contient une pile de type bouton/pièce de monnaie. Si la pile de type bouton/pièce de monnaie est
avalée, elle peut causer de graves brûlures internes en seulement 2 heures et peut entraîner la mort.
●
Gardez les piles neuves et usagées hors de portée des enfants. Si le compartiment de la pile ne se ferme pas
correctement, cessez d’utiliser le produit et gardez-le d’atteinte des enfants.
Si vous suspectez que des piles ont été avalées ou insérées dans une partie du corps, consultez un médecin
sans tarder.
4_ overview
Contents
overview
Important Safety Instructions
24
3
Product User Manual Description
24
Check Event List
3
Target Audience
25
Event Search
3
How to Use the Product
25
Event Instant Viewer
5
Contents
25
Stop Alarm Output
26
getting started
9
live
13
9
Starting the system
9
installation Wizard
12
Shutting down the System
12
Restarting the System
12
Login
13
17
23
Screen Layout of the Live
14
Checking the System Status
15
Check Camera List
15
Live Screen Menu
16
Icons on the Live Screen
29
Live Screen Mode
17
Changing the Pattern of Split Screen
18
Switching the Split Mode
19
OSD Information Display
19
Channel Information Display
20
Check the Camera Status
21
Channel Setting
22
Changing Overall Channel Aspect Ratio
22
Full Screen Mode
Setting Up the Live Layout
23
Check Layout List
23
Add Layout and Set Name
23
Change of Layout Channel and Name
23
Delete Layout
23
Play Layout Sequence
search
32
Real-Time Event Monitoring
• overview
3
3
Camera Video Control
26
Capture
26
Instant Viewer
26
Temperature Detection Mode
27
PTZ Mode
27
Zoom In
27
Audio
28
Display Text
28
Change Channel Aspect Ratio
PTZ Control
29
Getting Started with PTZ Operations
29
PTZ Control Menu
30
Using Digital PTZ (D-PTZ) Function
30
Preset
30
Running Preset
30
Running Swing (auto pan), Group (scan), Tour, or
Trace (pattern)
31
Exporting the Recorded Video
32
Screen Layout of the Search
32
Time Search
33
Event Search
33
Text Search
34
Export Search
34
ARB Search
35
Bookmark Search
35
Smart Search
English _5
overview
AI search
36
36
Screen Layout of the AI Search
36
Person Search
57
Storage Device
37
Face Search
61
Distributed Recording
37
Vehicle Search
62
S.M.A.R.T
38
LP Search
62
Monitor
38
LPR SEARCH
64
Text
57
65
play
39
42
Screen Layout of the Play
65
IP & Port
40
Play Search Results
67
DDNS
40
Time Line Adjustment
68
IP Filtering
40
Open Time Line Channel
68
HTTPS
40
Play Button Name and Function
69
802.1x
69
E-mail
70
SNMP
71
DHCP Server
71
Failover
73
P2P
Search Results Export
42
Screen Layout of the Setup
42
Setting the Camera
50
52
6_ overview
Setting the Network
39
41
setup
Setting the Device
42
Setting the Channel
45
Setting the Camera Functions
46
Setting the Profiles
50
Setting Camera Password
73
Setting the Recording
50
Record schedule
51
Record Setup
51
Record Options
Setting the Event
52
AI engine
52
Event setup
55
56
56
ONVIF Setup
57
Schedule
starting web viewer
80
80
Setting the System
73
Date/Time/Language
74
User
77
System Management
78
Log
What is Web Viewer?
80
Product Features
80
System Requirements
80
Connecting Web Viewer
Event Rule Setup
81
Set the recorder password
Alarm Input
81
installation Wizard
live viewer
Screen Layout of the Live Viewer
84
Checking the System Status
92
PTZ Control Menu
84
Checking User ID
93
Using Digital PTZ (D-PTZ) function
84
Checking Camera List
93
Preset
85
Checking the All Camera Status
93
Running Preset
93
Running Swing (auto pan), Group (scan), Tour, or
Trace (pattern)
85
Live Status
85
Record Status
85
Network Status
85
PoE Status
86
Changing the Pattern of Split Screen
86
Changing Overall Channel Aspect Ratio
87
Full Screen Mode
87
Setting up the Live Layout
88
87
Check Layout List
87
Add Layout and Set Name
88
Change of Layout Channel and Name
88
Delete Layout
Real-Time Event Monitoring
88
Event Type and Camera Settings
89
Check Event List
89
Event Instant Viewer
89
Stop Alarm Output
90
Live Screen Menu
90
Camera Video Control
90
Capture
90
PC Recording
90
Instant Viewer
90
Microphone Output
91
PTZ Mode
91
Zoom In
91
Audio
91
Image Rotation
92
Channel Aspect Ratio
92
search viewer
95
AI search viewer
98
PTZ Control
94
Exporting Video
95
Screen Layout of the Search Viewer
96
Time Search
96
Text Search
97
Bookmark Search
97
Search Results Export
98
Screen Layout of the AI Search Viewer
98
Person Search
99
Face Search
99
Vehicle Search
100 LP Search
100 LPR SEARCH
101 Search Results Export
play
102
102 Play Search Results
102 To Adjust the Time Line
102 Export Video by Section Setup
103 Play Button Name and Function
English _7
• overview
83
83
overview
setup viewer
104
104 Screen Layout of the Setup Viewer
104 Setting the Camera
104 Register
104 Channel Setup
export viewer
118
118 SEC Backup Viewer
118 Recommended System Requirements
118 Screen Layout of the Backup Viewer
105 Camera Setup
105 Profile Setup
106 Camera Password
106 Setting the Recording
106 Record Schedule
106 Record Setup
107 Record Options
107 Setting the Event
107 AI engine
107 Event Setup
109 Event Rule Setup
109 Alarm Input
109 ONVIF Setup
109 Schedule
110 Setting the Device
110 Storage Device
111 Monitor
111 Text
112 Setting the Network
112 IP & Port
112 DDNS
112 IP Filtering
113 HTTPS
113 802.1x
113 E-mail
114 SNMP
114 DHCP Server
115 P2P
115 Setting the System
115 Date/Time/Language
116 User
116 System Management
117 Log
8_ overview
appendix
120
120 Use Joystick
120 Using Virtual Keyboard
121 Troubleshooting
getting started
Starting the system
installation Wizard
1. Connect the power cable of the recorder to the wall outlet.
As shown below, proceed through each step of the <Installation wizard>.
Install Wizard can only be accessed at factory reset. If you do not want to proceed, click <Exit>.
2. You will see the initialization screen.
The initialization process will last about 2 minute. If a new HDD is installed, the initialization process may take longer.
1. In the <Language> screen, select the language and press the <Next> button.
3. The live screen appears with a beep.
The following symptoms might be observed when starting the system.
￭ If the HDD number is displayed at the bottom of the screen along with <
> while the product is booting up, it indicates that the HDD is in recovery,
and for this reason booting up may take longer.
2. Set the network connection type and the connection environment on the <Network> screen, and then click the
<Next>.
HDD 1, 2
￭ If the progress stalls while in <
> state, it indicates that the HDD has problems. Visit your nearest customer service center to check the HDD.
Setting up the DHCP server
HDD 2
If you set up the DHCP server to <Run>, the IP address is automatically assigned to your camera.
For more details, refer to the "Setup > Setting the Network > DHCP Server" page in the Table of Contents.
￭ Depending on the camera's state, no IP may be automatically assigned to the camera. After exiting the installation wizard, go to the menu to
assign an IP to DHCP, or set the IP manually.
English _9
• getting started
￭ It will automatically change to the optimal monitor resolution and run the install wizard.
￭ If the install wizard does not run, remove the monitor connection from the back of the recorder, reboot the recorder and reconnect the monitor.
getting started
Setting up the network
Each product supports a different number of network ports. If it supports two or more network ports, you can set
the network for each function as follows. Click <Setup> of the network connected to the recorder.
●
Network 1 (Camera) : Can be used as a port for connecting a camera. If you connect a camera, then the camera
video will be transmitted.
●
Network 2 (Viewer) : Can be used as a port transmitting video to the web viewer. If you access the network
information on your browser, then you can remotely monitor video in your web viewer.
●
Network 3 (iSCSI) : Can be used as a port for an iSCSI connection.
●
3. Set the administrator password on the <Recorder ID/PW> screen and click the <Next>.
Click <
> to view the basic guide for setting a password. Refer to the password setup rules.
￭ Only provided for products that support Network 3.
Network (All) : Can be used as a common port for connecting camera, web viewer, and iSCSI.
– IP type : Allows you to select the type of network access.
– IP Address, Subnet Mask, Gateway, DNS
￭ Manual : IP address, subnet mask, gateway, and DNS can be directly entered.
￭ DHCP : IP address, subnet mask, gateway, and DNS can be automatically set.
￭ If the LAN cable is not connected to the port, <Setup> button will not be activated for use. Check the LAN cable connection.
(In case of a PoE product, Network 1 is activated.)
￭ The built-in DHCP Server in Recorder will turn on automatically at stage 1. At this stage, using the existing DHCP server in the same network
may cause a problem, as two DHCP servers would be simultaneously operating.
￭ A product with multiple network ports cannot use a single bandwidth for all of them.
4. Set the camera password in factory reset on the <Camera ID/PW> screen.
If ID/PW is already set in the camera, register the ID/PW and click <Next>.
Example)
–– Port 1 : 192.168.100.199 / Port 2 : 192.168.100.198 (X)
–– Port 1 : 192.168.100.199 / Port 2 : 192.168.101.198 (O)
Setting the camera registration method
This function is only available for products that support PoE. For products that support PoE, see "Products
supporting each feature" (Page 4) in the Product Specification Manual.
●
Enable PnP mode: Cameras connected to the PoE port of the product will automatically be registered for each
channel in order of port number.
– When the camera resets to factory default, it defaults to the ID and password set during the <Camera ID/
PW> step. If the camera ID and password are not set, the recorder ID and password will be set automatically.
– If the camera's ID and password have already been set, the information that matches the ID and password
set during the <Camera ID/PW> step will be registered (up to 3 sets).
If your camera uses a manual IP, its bandwidth should match with that of Network 1 IP for registration.
– If manual mode is used, it automatically detects and registers cameras connected to the recorder’s PoE port
and cameras connected to a separate switch.
Online Upgrade
You can receive a new firmware notification when the recorder is connected to a network.
10_ getting started
￭
￭
￭
￭
When the password is in factory reset, it can be changed and managed in a batch.
Up to 3 sets of camera ID with password and password can be registered.
You may change the passwords of registered cameras all at once in the "Setup > Camera > Camera password" menu.
You cannot change the password for cameras registered with ONVIF and RTSP.
5. Set the date, time, and daylight saving time on the <Date & Time> screen, and then click the <Next>.
7. On the <Camera register> screen, select a camera to register from the searched camera list and click <Register>.
Select a camera to register from the list and click <Change IP>.
After completing camera register click <Next>.
• getting started
￭ The time zone setup might differ depending on the region that the product is released.
6. To set the recommended resolution on the <Resolution> screen, click <Apply> followed by the <Next> button.
￭ After entering the ID and password set in the camera, the connection test must be completed to successfully register.
8. On the <Channel setup> screen, you can view the camera videos registered to each channel in thumbnails along
with thumbnail information. To change the camera video position, select a video and drag and drop it to the desired
location.
￭ This function is not supported in some models.
9. Click <Finish> to complete the Installation wizard.
English _11
getting started
Shutting down the System
Login
1. Select <Shutdown> at the top right of the screen.
To use the Recorder menu, you are required to login as a user that is authorized to access the applicable menu.
2. The <Shutdown> window will appear.
1. Select <Login> at the top right of the screen.
3. Click on <OK>.
2. The <Login> window will appear.
The system will shut down.
Restarting the System
1. Select <Restart> at the top right of the screen.
2. The <Restart> window will appear.
3. Click on <OK>.
The system will restart.
￭ Only the user with the "Shutdown/Restart" permission can shut down or restart the system.
￭ To manage Permission Setup, refer to the "Setup > Setting the system > User" page in the Table of Contents.
12_ getting started
3. Enter the user ID and password, then click <Login>.
￭ The initial administrator ID is "admin" and you will need to configure the password in the installation wizard.
￭ Please change your password every three months to safely protect personal information and to prevent the damage of the information theft. Please,
take note that it’s a user’s responsibility for the security and any other problems caused by mismanaging a password.
￭ For more information about limited-access permission, refer to the "Setup > Setting the System > User" page in the Table of Contents.
live
Shows the video of the camera connected to the recorder. Also, you can adjust the camera and check the network
transfer status.
Item
Description
Displays information of the OSD screen on the video window.
Screen Layout of the Live
Shows channel information.
The live screen is built as follows.
• live
Shows the status of all cameras connected to the recorder.
Moves the page of the split mode.
Moves to the next page of the split mode according to the set time.
Sets the split screen of the video window.
Shows the video in actual proportions.
It changes to full screen from the current split mode.
Video window
Shows the video of the camera connected to the recorder.
The ID of the connected user is displayed.
Displays a QR code to download the user manual.
Stops the alarm at the notification display of the system status.
Item
Menu
List/Event
Description
Click each menu to go to the corresponding menu screen.
●
●
List : Select to check the camera list.
Event : Select to check the event list
The list of cameras registered in the recorder is displayed.
Camera list
You can also register the camera manually or automatically.
●
●
Event List
Layout list
PTZ control
System status display
Displays the status of the system, hard disk, and network.
2020-06-11 19:56:32
Displays the current time and date.
￭ If the camera's frame rate is set to 60 fps, the frame rate could be reduced on the live screen depending on the monitor resolution output.
: Registers the camera manually.
: Searches and registers the camera connected to the recorder automatically.
A list of events that have occurred on the camera is displayed.
Displays the default layout and a list of created layouts.
You can also set and play a sequence of layout lists.
Controls the connected PTZ camera.
Saves the recorded video of the selected channel in the designated path in a recorder or SEC format.
Clears the alarm in the event list and stops the alarm at the notification display of the system status.
Activates the manual recording function of the recorder.
English _13
live
Checking the System Status
Item
The icon at the top of the screen indicates the status of the system.
Description
Displayed if the server has firmware to update.
It is displayed when the system is overloaded.
￭ Limit the number of users remotely monitored by Web Viewer or VMS, or control the number of events displayed in the event list
of the recorder.
Displayed when manually recording a video while the access restriction for stop recording is enabled.
Only a user with the permission to stop recording is allowed to stop recording.
Displayed when exporting a recorded video in live mode.
Displayed when there is software to update on the camera.
Displayed when playing the layout sequence.
Item
Description
Displayed when running automatic switching of the split screen.
It is displayed when there is a problem with the fan.
￭ Only provided for products that support fans. (See page 4 of the Product Specification Manual)
Displayed when an error occurs in the internal memory.
It is displayed when there is a problem with the power supply.
￭ Only provided for products that support power supply redundancy. (See page 4 of the Product Specification Manual)
Display when recording data is not properly saved.
Error Information
●
If the built-in HDD is not connected, the "NO HDD" icon (
) will be displayed. You must contact the service
center since the Recording, Play, Export, and Upgrade functions do not work while doing this.
●
If you do not format a purchased HDD in a format supporting Recorder, a "NO HDD" icon (
) will be
displayed. If the "No HDD" icon is displayed, check the hard disk connection status in "Setup > Device >
Storage device" and format the hard disk.
●
If a product with a fan does not work or has a problem with the fan, <Fan Information Window> appears and
the fan malfunction icon (
) is displayed. In this case, check the fan inside the product. If the fan is defective,
it can shorten the product life cycle, so please make sure to contract service center nearby.
Displayed if the HDD is full and the Recorder has an insufficient space to record.
Displayed when there is no HDD or HDD is not detected.
Displayed if the HDD needs a technical examination.
It is displayed when RAID contains a malfunctioning HDD or cannot be used due to HDD malfunction.
￭ Only provided for products that support RAID.
It is displayed when recovering a RAID Error.
￭ Only provided for products that support RAID.
Appears when input data rate per channel exceeds the specified data rate limit.
It is displayed when an ISCSI device is disconnected.
￭ Only provided for products that support iSCSI.
It is displayed when the network is overloaded.
￭ It occurs when the max receiving allowance is exceeded, causing an overload to the CPU. It disappears when you modify the
Delete Camera or Set Camera to reduce the data rate.
14_ live
￭ If an abnormal fan (
) icon or NO HDD (
) icon, HDD FAIL (
) icon is displayed, contact our customer service.
Check Camera List
Live Screen Menu
Displays the camera type, status, and name registered in the recorder.
After selecting the desired channel on the split mode, roll the mouse cursor over the screen to see the live screen
menu.
The live screen menu appears differently depending on the recorder operation status or the type of the
registered camera.
Itrem
Channel information
• live
￭ Each function may be restricted depending on the type of camera and the user's authority.
￭ For more detailed information about each function, refer to the table of contents "Live > Camera Video Control".
Description
Displays channel information (channel number, video window assignment, and color indication).
Displays a normal camera.
Camera type
Displays a PTZ camera.
Recording an event video.
Camera status
Recording a general video.
Displays the camera error status.
Camera name
Displays the name set for the camera.
￭ If a camera connection error occurs, it is disabled in the list.
￭ The camera status display information changes according to the network connection status and settings.
Item
Description
Capture
Instant Viewer
You can take a screenshot of the selected channel.
You can rewind 30 seconds while monitoring the video.
Temperature Detection
For images that support the thermal imaging camera function, you can click the desired point to
check the temperature information.
PTZ control
If the network camera connected to the selected channel supports the PTZ function, it changes to
the PTZ control mode.
Zoom in
Audio
Display Text
Channel aspect ratio
You can zoom in or zoom out the video.
Turns the audio on or off when the audio is connected.
Turns the text output on or off.
Shows the video in actual proportions.
English _15
live
Icons on the Live Screen
Item
You can check the status or operation with the icons on the live screen.
Description
Events from the recorder and camera are displayed in icons.
￭ The icons displayed on the screen may differ depending on the type of camera and the user's authority.
Event Display
For details, refer to the "Setup > Setting the Event > Event rule setup" page in the
Table of Contents.
It is displayed on the channels that can enable the PTZ mode.
Displays AUDIO ON/OFF.
It will not be displayed when <Off> is selected for the audio in the channel setup.
If the alarm in is set, it is displayed on the connected channel when an external signal is
entered.
If the event detection is set for each channel, it is displayed when a camera event occurs.
It is displayed when it fails to decode all the frames due to limited decoding performance
and in this case only the I-Frame is decoded.
Status Display
Item
Displays camera's recording status and name.
Recording status and camera name
●
: Displays the event recording.
●
: Displays the normal recording.
Displayed when there is no input while the camera is on.
Video input status
This is displayed when a POS (text) event occurs.
Description
Displayed when there is an error with the SD card.
Displayed when the SD card capacity is full.
Displayed when the resolution of the live video exceeds the supported range while the
camera is on.
Displayed when a defocus event occurs.
Displayed if no permission to live view is granted.
Displayed when a fog detection event occurs.
Displayed when the camera is not registered.
If you set the channel setup to <Covert2>, nothing will be displayed on the live screen.
￭ If you set the channel setup to <Covert1>, the video will not displayed on
the live screen, but only the OSD will be displayed.
16_ live
Displayed if the Wisenet camera's certificate is valid.
￭ Each product may support different split view modes.
Live Screen Mode
You can display your camera's live video in various split modes.
￭ The 'Live4NVR' profile is added automatically with network camera auto registration, and settings can be changed according to user
￭
￭
CH1
CH2
CH1
Single mode
CH1
Horizontal 2-split screen
CH2
CH1
Vertical 2-split screen
CH2
CH2
Changing the Pattern of Split Screen
To change the split mode, click <
> at the bottom of the screen to select the desired split mode.
CH1
CH2
CH4
CH3
CH4
CH1
CH10
CH11
CH12
CH5
CH1
CH5
CH6
6-split mode
(1+5 split mode)
CH5
CH6
CH8
CH3
CH4
4-split mode
CH2
CH3
CH1
CH2
CH3
CH4
CH5
CH6
CH8
CH9
CH3
CH1
CH3
CH2
Vertical 3-split screen
CH1
CH2
CH3
CH4
CH7
CH5
CH6
CH7
CH8
CH9
CH9
CH10
CH11
CH12
CH13
CH13
CH14
CH15
CH16
13-split mode
(1+12 split mode)
16-split mode
CH1
CH2
CH3
CH4
CH5
CH6
CH7
CH8
CH9
CH10
CH11
CH12
CH13
CH14
CH15
CH16
CH17
CH18
CH19
CH20
CH21
CH22
CH23
CH24
CH25
CH26
CH27
CH28
CH29
CH30
CH31
CH32
CH33
CH34
CH35
CH36
CH37
CH38
CH39
CH40
CH41
CH42
CH43
CH44
CH45
CH46
CH47
CH48
CH49
CH50
CH51
CH52
CH53
CH54
CH55
CH56
CH57
CH58
CH59
CH60
CH61
CH62
CH63
CH64
CH4
CH6
CH7
CH8
CH7
8-split mode
(1+7 split mode)
9-split mode
CH1
CH2
CH3
CH4
CH5
CH6
CH7
CH8
CH9
CH10
CH11
CH12
CH1
CH2
CH3
CH4
CH5
CH6
CH7
CH8
CH9
CH10
CH11
CH12
CH13
CH14
CH15
CH16
CH17
CH18
CH19
CH20
CH25
CH26
CH27
CH28
CH29
CH30
CH21
CH22
CH23
CH24
CH25
CH31
CH32
CH33
CH34
CH35
CH36
25-split mode
CH13
CH14
CH15
CH16
CH17
CH18
CH19
CH20
CH21
CH22
CH23
CH24
36-split mode
64-split mode
English _17
• live
￭
￭
environment.
Live4NVR Profile Basic Settings : H.264 (codec), 800 x 600 or 800 x 448 (resolution), 30fps (frame rate)
Depending on camera specification, you may not be able to add a profile or if you have the PLUGINFREE profile, you will not be able to add the Live4NVR
profile.
When system overloaded and the performance is down, network camera may play only main frame(I-frame).
To set profiles, refer to "Setup > Setting the Camera > Setting the Profiles" page in the Table of Contents.
live
Switching the Split Mode
Example 2) 16-channel model
You can split the live video from cameras to Single, 4-split, 9-Split, or 16-split mode and watch them one by one.
￭ Each product supports different split modes.
13-16
16
10-16
Auto Sequence
To switch the screen automatically, click <
> at the bottom of the screen.
You can monitor the split mode of your own choice by switching one after another at a certain interval.
1-9
1-4
1
4-split mode
Single mode
9-split mode
Manual Switching
Click
or
at the bottom of the screen or enter a page number to go to that page.
￭ When you switch the channel, the video may be delayed depending on the network condition.
Example 1) 64-channel model
Example 1) After setting to 16-split mode for the 64 channel model, if the right (
61-64
64
1-4
Single mode
4-split mode
1
Channel(CH 1~16) ➡ Channel(CH 17~32) ➡ Channel(CH 33~48) ➡ Channel(CH 49~64)
CH1
CH2
CH3
CH4
CH17
CH18
CH19
CH20
CH33
CH34
CH35
CH36
CH49
CH50
CH51
CH52
CH5
CH6
CH7
CH8
CH21
CH22
CH23
CH24
CH37
CH38
CH39
CH40
CH53
CH54
CH55
CH56
CH9
CH10
CH11
CH12
CH25
CH26
CH27
CH28
CH41
CH42
CH43
CH44
CH57
CH58
CH59
CH60
CH13
CH14
CH15
CH16
CH29
CH30
CH31
CH32
CH45
CH46
CH47
CH48
CH61
CH62
CH63
CH64
Example 2) After setting to 4-split mode for the 16 channel model, if the right (
64
55-63
49-64
1-16
9-split mode
18_ live
1-9
) button is clicked:
Channel(CH 1~4) ➡ Channel(CH 5~8) ➡ Channel(CH 9~12) ➡ Channel(CH 13~16)
) button is clicked:
CH1
CH2
CH5
CH6
CH9
CH10
CH13
CH14
CH3
CH4
CH7
CH8
CH11
CH12
CH15
CH16
16-split mode
OSD Information Display
Channel Information Display
You can show or hide the recording status, camera status, event display, etc. in the video window.
You can check the information of the video being recorded with each camera.
To show or hide the OSD information, click <
To check the channel information, click <
> at the bottom of the screen.
> at the bottom of the screen.
• live
The information of the current video is displayed on the live video which is being monitored.
800x448 (H.264)
S/I/D 25/24.9/24.9
XNV-6081Z(S)
●
800x448 : Displays the resolution of the video.
●
H.264 : Displays the video codec.
●
S/I/D 25/24.9/24.9 : Displays the frame rate (FPS) of the video. (S : Settings, I : Video input, D : Video display)
●
XNV-6081Z : Displays the camera model name.
●
CH1 : For multi-channel cameras, the channel number is be displayed. The channel number may not be
displayed depending on the camera.
●
S : Displays the protocol used when registering the camera.
– S and V represent Wisenet protocol while O represents ONVIF.
– When connected by RTSP protocol, only RTSP is displayed without the product name.
￭ ARB is only visible when an ARB situation occurs.
English _19
live
Check the Camera Status
Record Status
You can check the status of all cameras connected to the recorder.
If you select <Record> in the <Status> menu, you can check the profile, record type, frame rate (Input/Record),
and bit rate (Limit/Input/Record) for each channel.
To check the camera status, click <
> at the bottom of the screen.
●
Total bitrate (record/max) : Record shows the amount of data currently being recorded, and Max shows the
amount of recorded data allowed for the recorder.
●
Current : Shows the recording status information of currently transferred data.
●
Max : Shows recording information of the most biggest recording data out of configured standard and event
recordings.
Live Status
Select <Live> in the <Status> menu to check the transmitted data from a network camera connected to each
channel.
●
: Reloads the recording information.
●
Profile : Shows the video profile configured to each channel.
●
Record type : View the record type according to normal or event recording.
●
Frame rate (fps) : Shows the receive/record frames per second for each channel.
●
Bitrate (bps)
– Limit / Receive / Record : Shows the amount of limit/receive/record data for each channel.
– Receive/Limit : Shows the data ratio of actual data transferred from the camera and allowed maximum
defined by user.
●
●
Model : Displays the model name of camera connected to each channel.
●
Status : Shows the connection status of camera set to each channel.
●
IP address : Displays the IP address of a camera set to each channel.
●
Codec : Displays the live profile codec information for a camera set to each channel.
●
Resolution : Displays the live profile resolution of a camera set to each channel.
●
Frame rate : Displays the live profile transmission rate for a camera set to each channel.
20_ live
Record setup : You can set detailed recording settings.
For more details, refer to the "Setup > Setting the Recording > Record Setup" page in the Table of Contents.
￭ If an error occurs during recording, the channel's profile column turns yellow.
This profile error indicates that when a recording profile cannot be used to receive video from camera, an alternative profile is used to record the
video. When the recording profile resumes, the camera video can record by using the set recording profile.
￭ If Recorder exceeds the recording limit, only the key frame will be recorded. In that case, a restricted recording popup and an icon will appear.
The restricted recording popup appears only once. If you change the camera setup and record setup, the restricted recording popup may appear
once more to confirm the status.
If you don't want to see it again, then check Do not show this again in the popup.
For the maximum allowed number of recoding, refer to the "Setup > Setting the Recording > Record Setup" page in the Table of Contents.
￭ For dual recording, the bitrate is shown as the sum of recording and remote profiles.
However, the <Enable dual recording> box in the "Record > Record options" menu must be checked.
The recording profile and remote profile can be set in the "Camera > Profile setup" menu.
CH1
CH2
CH3
CH10
CH11
CH12
CH2
CH14
CH15
CH1
CH4
CH5
CH6
CH2
CH7
CH2 CH2
CH8
CH2
CH3
CH9
CH3
CH4
CH3
CH3 CH6
CH6
CH4
CH4 CH8
CH8
CH12
CH7
CH8
CH8 CH10
CH10
CH11
CH13
CH16
CH4
CH5
CH3
CH1
CH4
CH5
Network
Status
CH7
CH7
●
CH1
CH9
CH9
Select
<Network>
in the <Status> menu to check the status of network bandwidth currently being received/
CH2
CH2
CH1
CH1
CH1
CH11
CH12 CH1
CH13
CH12 transmitted.
CH13
CH5
CH6
CH9
CH10
CH13
CH14
CH2
CH2
CH4
CH5
CH7
CH2
CH8
CH2
CH3
CH1
– Checked
(
CH5
CH5
CH6
CH6
CH7
CH7
CH4
CH1CH2
CH9
CH4
CH5
CH2CH3
CH7CH3
CH5
CH5CH6 CH10 CH6
CH9
CH7
CH7CH8
CH8CH9
CH11
CH2
CH3
CH1
CH6
CH1
CH1
CH10
CH9 CH3
CH13
CH14
CH12
CH11
CH11
CH12
CH15
CH16
CH8
CH10
CH2
CH12
CH3
CH4
CH4
CH15
CH16
CH15
CH3
CH16
CH9
CH16
CH3
CH4
CH10
CH11
CH4
CH5
CH11
CH12
CH2
CH3
CH5
CH4
CH12
CH13
CH19
CH13
CH1
CH1
CH2
CH2
CH1
CH1
CH5
CH6
CH9
CH10
CH13
CH14
CH7
CH8
CH11
CH12
CH15
CH16
Detailed
information:
If there is a problem with power supply, it is described here. Power supply problem
CH13
CH14
CH15
includes overload power (Class 1 to 4) and voltage fault.
CH16
CH1
CH15
): Power supply limited
Total power consumption (W): Displays the sum of power consumption of all ports.
Channel Setting
CH14
CH14
CH4
CH8
CH1
CH8
CH1
CH19
): Power
supply
available
– Not CH11
checkedCH12
(
CH10
●
CH4
CH2
CH2
CH8
CH13
CH12
CH1
CH1
CH1
CH2
CH1
CH2 CH2
CH3
CH3
CH3
• live
CH1
CH8
CH6
CH13
CH11
CH4
CH7
CH8
●
CH15
CH3
CH10
CH3
CH6 supply toCH7
CH7
CH3
Enable: Turns on/off
the CH6
power
the camera.
CH1
CH1
CH2
CH1
CH4
CH1
CH8
CH1
CH5
CH6
CH7
CH9
CH10
CH11
CH12
CH13
CH14
CH12
CH15
CH16
CH7
CH2
CH3
CH4
CH5
CH6
CH1
CH8
CH9
CH10
CH11
CH12
CH13
CH14
CH15
CH16
CH5
CH6
CH9 CH5
CH10 CH6
CH4
CH4in a
CH6
You
can display
the channel
desiredCH5area
of a split screen.
CH2
CH13
CH2
CH14
ToCH1switch
channel,
holdCH8a channel
andCH4drop
CH1 the position of a CH7
CH3
CH4it to the desired location.
CH7 CH8
CH9 and
CH3 drag
CH9
CH1
CH7
CH8
CH11
CH15
CH3
CH16
CH1
Example) If switching CH 1 to CH 7
CH4
H11CH12
CH12
CH8
H14CH15
CH1
CH15
supports a different number of network ports.
￭ Each product
CH1
CH12
CH3
CH16
CH2
PoE Status
CH6
CH8
CH9
CH9
CH11
CH11
CH10
CH10
CH13
CH13
CH14
CH14
For products that support PoE, see "Products supporting each feature" (Page 4) in the Product Specification
Manual.
CH12
CH15
CH16
CH12
CH15
CH16
Select
<PoE> in the
<Status>
menu to check the current PoE status of each port.
CH1
CH10
CH2
CH3
CH4
CH10 CH11
CH11 CH12
CH5
CH6
CH7
CH8
CH13
CH9
CH13 CH14
CH14 CH15
CH10
CH11
CH12
CH16
CH13
CH16
CH14
CH15
CH16
CH7
CH2
CH3
CH4
CH5
CH6
CH1
CH8
CH10
CH11
CH12
CH15
CH3
Switching
to Single
ModeCH9
CH5
CH6
CH5
CH6
CH9
CH7
CH13
CH7
CH14
CH12
CH8
CH15
CH8
CH16
CH11
Example) If double-clicking CH 3
CH4
CH1
CH1
CH2
CH2
CH3
CH3
CH4
CH4
CH1
CH8
CH8
CH5
CH5
CH6
CH6
CH7
CH7
CH8
CH8
1
CH11
CH12
CH12
CH9
CH9
CH10
CH10
CH11
CH11
CH12
CH12
5
CH15
CH16
CH16
CH13
CH13
CH14
CH14
CH15
CH15
CH16
CH16
CH7
CH7
CH2
CH2
CH3
CH3
CH4
CH4
CH5
CH5
CH6
CH6
CH1
CH1
CH8
CH8
CH9
CH9
CH10
CH10
CH11
CH11
CH12
CH12
CH13
CH13
CH14
CH14
CH15
CH15
CH16
CH16
CH3
CH3
CH1
●
CH1
CH2
CH2
CH1
CH10
CH10
CH2
CH1
CH13
CH13
CH14
CH14
When in split mode, select and double-click a desired channel to switch to its Single mode.
CH3
CH4
CH1
CH9
CH1
CH11
CH12
CH12
CH15
CH15
CH16
CH16
CH1
CH3
CH3
CH1
CH1
CH2
CH2
CH1
Consumption (W) : Displays the power consumption in PoE.
– 0 : No device is connected to the port or device is using its own power supply.
– – : Port failure (Failure information is displayed in Detailed information.)
￭ If the total power of the port or the maximum power per port is exceeded, all ports will be powered off one by one.
For PoE power consumption of each product, see "Products supporting each feature" (Page 4) in the Product Specification Manual.
English _21
live
Changing Overall Channel Aspect Ratio
Full Screen Mode
Video screen ratio for all channels can be changed in live split screen mode.
You can change to full screen mode, which has no top/bottom/left/right areas of the live screen.
Click <
> at the bottom of the screen. It changes to the actual proportion of the video.
Click <
Click <
> to return to the previous aspect ratio.
Changes to full screen mode.
> at the bottom of the screen.
￭ To exit full screen, place your mouse cursor over the bottom of the full screen mode and click <
General mode
￭ You can change the aspect ratio of each channel. For more information, refer to the "Live > Camera Video Control > Change Channel Aspect
Ratio" page in the Table of Contents.
22_ live
>.
Full screen mode
Setting Up the Live Layout
Change of Layout Channel and Name
This section outlines how to select a series of channels based on their purpose/accessibility and monitor them in a
single layout.
1. Click <
List > at the top left of the live screen, and then click <
3. Click <
> to save the changed settings.
Delete Layout
Check Layout List
Click <
2. Add or delete channels or rename layouts.
• live
Example) Layout "Lobby" - Lobby camera 1, Lobby camera 2, Front entrance camera 2
Layout "VIP" - Directors' meeting room 1, Directors' meeting room 2, Directors' lounge 1, Corridor camera on
the 7th floor
> after selecting a layout.
Click <
> to display the layout list.
> after selecting the layout to delete.
￭ You cannot delete the default layout.
Play Layout Sequence
You can automatically switch the layout list to a set time interval to view.
Sequence Setting
Click <
●
: Create a new layout.
●
: Change the channel or name of the layout.
●
: Save the changed layout.
●
●
> at the bottom of the layout list to set the sequence.
: Delete the added layout.
/
: Open or close the layout list.
Add Layout and Set Name
1. Click <
> to add a layout.
2. Click <
> to set the name for the added layout.
●
Sequence switching time : Set the switching time of the layout list.
●
Sequence list : Set the layout sequence playback order. You can add the same layout repeatedly.
3. In the camera list, click to select the channel to be displayed on the layout screen.
4. Click <
> to save the set layout.
￭ Each layout is saved separately by the user.
￭ The layout set on the live screen can also be used for time search and can be searched according to the channel order and channel combination
set by the user. For more information, refer to the "Search > Time Search" page in the Table of Contents.
English _23
live
Play Layout Sequence
Real-Time Event Monitoring
Click <
Play sequence> at the bottom of the layout list to automatically switch the layout according to the
sequence settings.
Real-time events that occurred on the camera can be checked in the live video window and event list.
￭ AI events are only available for products that support AI.
￭ AI events are displayed only after setting event rules. AI event search may have different settings and operation specifications depending on the recorder
or camera.
Check Event List
Click <
Event> on the left side of the live screen to display the real-time event list.
￭ When new events occur, the list of events will be updated accordingly.
￭ The specified channels and events are displayed in the list according to the event rule setup.
For details, refer to the "Setup > Setting the Event > Event rule setup" page in the Table of Contents.
￭ <Play sequence> is active only when a sequence is set.
●
: Browses for the event by the desired condition.
●
: Plays the video at the time of the event.
￭ When an alarm output occurs, if event recording is set and pre-event time and post-event time are set, event recording is performed before or
after the event according to the set recording method. For more information about event recording settings, refer to the "Setup > Setting the
Recording > Record setup" page in the Table of Contents.
￭ The video may be delayed depending on the network condition.
￭ The event output can be delayed as the transfer of the alarm event from the network camera takes time.
24_ live
Event Search
Event Instant Viewer
You can browse events by camera and event type.
To search for a specific event, click <
> to select the event type and camera to browse.
Event filter
> to play the recorded video at the time the event
￭ Instant viewer can play an event video for 1 minute.
￭ For AI events, the best shot and details of the event that occurred are displayed.
￭ AI event recognition may have different settings and operation specifications depending on the recorder model or camera.
￭ To see AI events, set any of the following options as necessary : See the relevant page for detailed setup method.
• live
Displays only selected events in the event list.
Select an event to check from the event list, and click <
occurred.
–– Setup > Event > AI engine
–– Setup > Event > Event setup > Object
–– Setup > Event > Event setup > AI recognition
–– Setup > Event > Event setup > Mask
–– Setup > Event > Event setup > IVA
–– Setup > Event > Event rule setup
AI event
●
Common event : Searches for event types that have occurred in general cameras such as motion detection and
IVA.
●
AI event : Searches for AI event types such as face, person, and vehicle.
Common event
￭ AI events are only activated when an AI camera is connected.
￭ AI events are displayed only after setting event rules. For details, refer to the "Setup > Setting the Event > Event rule setup" page in the Table of
Contents.
Camera filter
Displays events for the selected camera only.
●
/
●
: Moves to the playback screen.
: The video is played/paused.
●
: Instant Viewer playback ends.
Stop Alarm Output
When an event occurs, an alarm can occur. Click <
necessary.
> at the bottom of the screen to stop the alarm output if
For details, refer to the "Setup > Setting the Event > Event rule setup" page in the Table of Contents.
English _25
live
Camera Video Control
Instant Viewer
By using the function icon of the video window, you can easily use the functions of capture, video zoom, PTZ camera
and thermal imaging camera. When you place your mouse over the video window, the live screen menu will appear.
You can move the video back 30 seconds and play it while live monitoring. Instant viewer plays video from 30
seconds to 1 minute from the current time.
Select the desired channel and click <
The Instant Viewer screen appears.
Capture
You can take a screenshot of the current video of a specific channel selected on the live screen.
1. Select a channel to capture video and click <
>.
●
/
●
: Moves to the playback screen.
●
: Instant Viewer playback ends.
>.
: The video is played/paused.
2. Select the output information to be displayed on the captured screen.
Temperature Detection Mode
For images that support the thermal imaging camera function, you can click the desired point to check the
temperature information.
Select the desired channel and click < >.
When you place your mouse over the video, the mouse pointer changes to a thermometer shape, and when you
click a specific location on the video, the temperature at that location is displayed next to the mouse pointer.
36.5°
3. Set the device where the screenshot file will be saved and the file name.
4. Complete the settings and click <OK> then the image captured from the screen is saved to the selected
device.
￭ Camera screen larger than 2 megapixels is captured in Full HD size.
●
●
26_ live
: Exits temperature sensing mode.
: The color of the video changes according to the temperature color selection.
PTZ Mode
Zoom In
You can run PTZ control of the selected channel.
You can zoom in or out the video via digital zoom.
Select the desired channel and click <
Select the desired channel and click <
>.
Enters the PTZ control mode.
Enters the digital zoom mode.
●
: The PTZ mode is closed.
●
: Captures video of the current state.
●
: After clicking the digital zoom icon, you can use <
●
: Returns to the 1x zoom screen.
￭ In PTZ mode, click <
●
/
> to zoom in or zoom out the video.
●
> to run the digital zoom.
: Exits the digital zoom mode.
/
: Zooms in or out the video.
Minimap : When the video is enlarged 10%, a minimap is displayed. You can quickly check the desired location
in the enlarged video through the mini-map.
Adjusting the Camera Direction
Audio
When you rolls over the mouse to <
>, the 8-way key appears, and when the mouse leaves the area of the
direction key, the direction key disappears. You can fine-tune the camera direction by clicking the 8-direction key
once. Keep clicking the arrow keys to move in the desired direction and release the mouse to stop.
You can turn the sound on/off corresponding to the channel in Live mode.
To quickly adjust the direction of the camera, click <
> and drag. The screen moves quickly in the desired
direction. You can adjust the screen movement speed according to the drag distance.
Moving to the Center of the Screen
Click a specific location on the screen to move the video at that location to the center of the screen.
• live
￭ Depending on the camera, the PTZ control function and speed may be different.
●
>.
Select the desired channel and click <
>.
Audio output can only be turned on in one channel. The audio output of other channels will be automatically
turned off.
￭ If you have configured the audio output settings properly but the audio or voice is not output, check if the connected network camera supports
the sound signal and if you have configured the sound settings as appropriate.
The sound icon can be displayed if the sound signal fails to output from noise.
￭ Only the channel where <Audio> is set to <On> in "Setup > Camera > Channel Setup" displays the audio icon (
you can use to turn the sound on/off.
) in Live mode that
Zooming the Selected Area
Drag a specific area of the screen, to move and the selected area to the center of the screen and zoom in.
Zooming In and Out of Images
You can zoom in or out using the mouse wheel. Click <
> to go back to the original size.
English _27
live
Display Text
Change Channel Aspect Ratio
You can monitor texts regarding the sales record received from POS in real time.
You can change the aspect ratio of each channel.
￭ This is executable when a text device is connected.
￭ The Recorder can display text on a live screen when a text device is set. For details, refer to the "Setup > Setting the Device > Text" page in
the Table of Contents.
Select the desired channel and click <
>.
When text information occurs, the text information is displayed in the corresponding video window.
Also, when a set text event occurs, the corresponding part of the text is displayed in a separate color.
Onions
CHIP
3.59
2.37
Apple
2.69
Goat
0.79
Peppers red, loose 0.59
2 x 0.79
Pasta
2 x 0.59
1.18
0.59
1.18
========================
TOTAL
3.63
<
> appears when text information crosses the screen. Click <
can check the entire content.
28_ live
> to display a popup window where you
Select the desired channel and click <
>.
It changes to the actual proportion of the video.
PTZ Control
Item
With this Recorder, you can configure the settings of a PTZ camera as well as commercial cameras in the market to your
preference.
Description
Zoom out/Zoom in
This is active only if a channel that a PTZ camera is connected to is selected.
Near/Far
You can adjust the focus manually.
Auto focus
You can adjust the focus automatically.
The PTZ camera will be activated only if the channel of the PTZ camera is selected. After selecting the desired
channel, click <
> on the live screen menu.
￭ This is available only if a PTZ camera is connected and the < > icon is displayed on the screen.
￭ Even if the connected network camera does not support the PTZ operations, you can configure the PTZ control settings (if possible) by installing
the PTZ driver (physical device).
￭ It only supports a network camera with Hanwha Techwin's PTZ function and a camera registered in the ONVIF.
Preset
Set the preset position to move the camera, and then select the desired preset to move to the
set position.
Swing
Swing is a monitoring function that moves between two preset points and enables you to
trace the motion.
Group
The group function enables you to group various presets before calling them in sequence.
Tour
Monitor all the groups created by a user in turn.
Trace
Tracking remembers the trace of movements that you instructed and reproduces it for your
reference.
PTZ Control Menu
You can use a single PTZ camera to perform the Pan, Tilt and Zoom operations to monitor multiple places, and
configure the custom settings of the presets in a desired mode.
Click <PTZ control
below.
> on the bottom left of the live screen to display the PTZ camera control menu as shown
The preset you set is saved and displayed in the list.
Deletes the selected preset list.
Preset List
Shows a list of saved presets.
￭ The PTZ working (active) mark can be active even if the PTZ operation is not available in normal mode. So ensure that you have completed the
PTZ settings before proceeding.
￭ Some cameras may differ in the menu title and operation with regard to Swing, Group, Tour and Trace.
￭ Even if your network camera supports the function, you can use it only if the button is activated in the PTZ control launcher.
English _29
• live
Getting Started with PTZ Operations
Activate the Zoom operation of the PTZ camera.
live
Using Digital PTZ (D-PTZ) Function
To delete a registered preset
1. Register a camera that supports the D-PTZ profile.
1. Click <
>.
2. Click <
>. <Delete preset> window will appear.
￭ In cameras that support the D-PTZ profile, you can use the D-PTZ function.
2. Both cameras that support general PTZ and cameras that support D-PTZ can control the live image using
some of the <PTZ control> function menus.
￭ For more information about the supported functions, please refer to the camera manual.
Preset
3. Click <
Preset is a set of saved data specifying the locations of a PTZ camera. A single PTZ camera can save up to 300
locations.
￭ The max. number of presets may vary depending on the number of presets supported by the camera.
4. Click <Delete>. The selected preset will be deleted.
Running Preset
1. Click <
To add a preset
1. Select the desired channel and click <
￭ The PTZ control screen appears.
>.
2. Use the arrow keys to adjust the camera to the point.
3. Click <
5. Click <
>, the <Preset setup> window will appear.
> to select the Preset Order to set.
6. Enter the Preset name.
7. Click <Save>.
The preset setting will be saved.
￭ If you replace a camera that saves your preset settings with a different one, you must configure the preset settings again.
30_ live
>.
2. Click the preset you want to run from the list.
The camera lens moves to the set position.
Running Swing (auto pan), Group (scan), Tour, or Trace (pattern)
The running method of each function is the same as the preset operation method. For details on how to use it,
refer to the camera's user manual.
>.
4. If you click <
> to select the preset to delete.
￭ Depending on the camera's capabilities, only some features may be available.
Exporting the Recorded Video
You can search the storage device to be exported and export the recorded video of the desired time by layout or
channel.
1. Click <
> at the bottom of the screen.
2. The export setup screen will appear.
●
●
￭
￭
￭
￭
Format the memory stick or delete some of the data on the memory stick to secure adequate storage space.
The operation speed of the product may slow down if the export is in which is a progress.
You can switch to the menu screen during export progress, but data playback will not be possible.
Data can be played in the web viewer during export progress, but audio will not be supported.
If the export fails, check the current capacity and status to see if the hard disk is connected properly in the "Device > Storage device" menu.
￭ If <Hide> is selected while the export is in progress, the screen changes to the upper menu, but the export continues.
• live
●
￭ If you insert a USB memory stick with insufficient storage space, volume calculation may be disabled.
Select a layout : Select a desired layout from the layout list.
Channel : Select a channel to export.
￭ You can select multiple channels. If you select <All channels>, all channels will be selected.
Export section : Set the <Start> and <End> time to run the export select to.
– Start : You can set the start time for the export to the desired time.
Click <Start> to set the export start time to the first time the video was recorded.
– End : You can set the end time for the export to the desired time.
Click <End> to set the export end time to the last time the video was recorded.
●
Overlap : Shows a list of overlapping data on a same time according to the number of data.
This is displayed when there are duplicate data in the same channel due to changes in the time or time zone.
●
Device : Select a device to export the among the searched devices.
●
File type : Select the export format.
￭ For more details, refer to the "Setup > Setting the System > Date/Time/Language" page in the Table of Contents.
– SEC : You can export in your own file format that can be played directly on your PC. You can play with the viewer
included in the export folder.
￭ If you select SEC format, you can choose whether to include "PW Setup" and "Include text data".
– Recorder : You can export to a file that can be played only on the recorder.
●
Path : Displays the folder location where the export file will be saved. You cannot change the storage folder, only
the file name to be saved.
●
Check capacity : You can check the selected export capacity and the current and remaining capacity of the export
device.
3. After completing the export setup, select <Start>.
￭ If there is no device to export, the <Start> button will be deactivated.
￭ If you click <Stop> during the export progress, which is the export will be canceled.
4. Click <OK> on the export completion confirmation window to finish.
English _31
search
You can search recorded video by various conditions such as time, event, and export.
Time Search
Screen Layout of the Search
You can search the recorded data by the desired date and time conditions.
￭ The time displayed will be based on the time zone and daylight saving time (DST) applied time zone, so it may be displayed differently depending on
whether the data time zone recorded at the same time and daylight saving time (DST) is applied.
1. Select <Time search> in the <Search> menu.
2. Select a channel to search.
3. Choose a layout.
Item
Description
Menu
Click each menu to go to the corresponding menu screen.
Search menu tab
Click the menu tab to display the detailed search menu. Click Search menu to go to the corresponding Search screen.
Search conditions
You can set various search conditions, such as date/time/event.
Search results
Displays search results.
4. Click , in the date selection window to select the year and month to search.
Dates with data will be shown in orange and current dates will be shown in orange circles.
5. Select a date to search from the calendar.
The first video of the searched data of the day will be displayed in the video window and the data will be displayed
in the time line.
●
Click <Today> to search for today's date. Today’s date will be selected.
●
If you click <Overlapped>, you can check the time line by setting the overlapping section by time change.
●
Export
/
Exports search results to a file.
Displays the search results as a list or thumbnail.
￭ Click <Reset> to initialize the search conditions and results.
￭ Double click on the desired item in the search results list to go to the play screen.
When you click Playback ( ), the video will be played in an instant viewer.
￭ You can specify a bookmark by clicking the bookmark ( ) in the search results list. You can check the specified video in the bookmark search menu.
￭ If the search results are in multiple pages , you can click to go to the previous/next page. Or, you can click the current page number and enter the
desired page to move.
32_ search
The displayed color differs depending on the type of recording data.
– Light green : Normal recording video
– Red : Event recording video
6. Double click the time of the desired channel to play the recorded video of that time.
Text Search
You can search for various events by channel.
You can search the data input to the POS device connected to the recorder.
1. Select <Event search> in the <Search> menu.
1. Select <Text search> in the <Search> menu.
2. Select a channel to search.
2. Select a date and time to search.
• search
Event Search
￭ If you select a channel to search, you can change the channel display mode by clicking <
>. You can select a desired channel by clicking or dragging it
3. Set the keyword item. When you click an item, the keyword setting window appears.
3. Select a date and time to search.
￭ You can search with a narrower range by entering specific characters.
●
Text search keyword : Enter the text to search.
4. Please select an event type. When you click the item, the event type selection window will appear.
●
Match case sensitivity : When checked, the entered characters will be searched with case-sensitivity.
●
Match whole words : When checked, only data that exactly matches the entered character will be searched.
●
Event keywords : You can search for text with preset event keywords. For more information about event keyword
settings, refer to the "Setup > Setting the Device > Text > Text Event Settings" page in the Table of Contents.
from the channel table, and clicking the channel in the channel list.
￭ Event type options : All, motion detection, IVA, face detection, auto tracking, tampering detection, Defocusing detection, fog detection, audio detection,
sound classification, alarm input(camera), continuous recording, manual recording, ObjectDetection.Person, ObjectDetection.Face, ObjectDetection.Vehicle,
ObjectDetection.LicensePlate, Mask detection
￭ Event type options may vary depending on the camera model.
5. Select the overlap.
It will be displayed when there is overlapped data in one channel by changing the time or time zone at the selected
time.
6. Click the <Search> button.
●
CH : Displays the channel where the event occurred.
●
Camera name : Displays the camera name.
●
Event : Displays the event type of the recorded video.
●
Time : Displays the start time and end time of the recorded video.
●
Playback : Plays the recorded video with an instant viewer.
●
Bookmark : Specifies a bookmark to the recorded video.
4. Select the overlap.
It will be displayed when there is overlapped data in one channel by changing the time or time zone at the selected
time.
5. Click the <Search> button.
●
Device : Displays the name of the POS device connected to the recorder.
●
CH : Displays the channel where the event occurred.
●
Keyword : Displays the searched text.
●
Time : Displays the start time of the recorded video.
●
Playback : Plays the recorded video with an instant viewer.
●
Bookmark : Specifies a bookmark to the recorded video.
6. If you double-click an item to play in the search list, the recorded video will be played.
7. If you double-click an item to play in the search list, the recorded video will be played.
English _33
search
Export Search
ARB Search
You can search the exported data on the connected storage device. Only data saved in recorder file format when
exported will be retrieved.
You can search auto-recovery backup data stored on ARB storage devices.
1. Select <ARB search> in the <Search> menu.
1. Select <Export search> in the <Search> menu.
2. When you click <Select storage device>, the device search window is displayed. Click <
device.
3. Click <Search>.
Exported file information will be displayed.
> to search for storage
￭ For more information about ARB search, refer to the "Setup > Setting the Device > Storage device" page in the Table of Contents.
2. When you click <Select storage device>, the device search window is displayed. Click <
device.
The model name of the ARB storage device will be displayed.
3. Click <Search>.
The ARB file information stored on the device will be displayed.
●
Folder : Displays the folder where files are stored.
●
Name : Displays the saved file name.
●
Folder : Displays the folder where ARB data is stored.
●
CH : Displays the channel of the recorded video.
●
Name : Displays the file name stored on the ARB device.
●
Time : Displays the start time and end time of the exported video.
●
CH : Displays the recorded channel.
●
Playback : Plays the exported video with an instant viewer.
●
Time : Displays the start time and end time of the backed up video recording.
●
Playback : Plays the recorded video with an instant viewer.
4. If you double-click an item to play in the search list, the recorded video will be played.
4. If you double-click an item to play in the search list, the recorded video will be played.
34_ search
> to search for storage
Bookmark Search
Smart Search
You can search for bookmarked data.
You can search for events by selecting a region of interest, an exclusive region, or a virtual line from a recorded video at
a specific time.
￭ To use smart search, you need to set the area of the camera's “Motion Detection" or “IVA” to the entire area. However, if you want to search for cameras
1. Click <
> on the video window menu.
2. Set the smart search area in the video window.
1. Select <Bookmark search> in the <Search> menu.
￭ To search for bookmarks, you need to specify them by clicking the bookmark ( ) in the instant viewer or search results. If no bookmark is specified, search
results will not be displayed.
2. Select a channel to search.
￭ If you select a channel to search, you can change the channel display mode by clicking <
>. You can select a desired channel by clicking or dragging it
from the channel table, and clicking the channel in the channel list.
3. Select a date and time to search.
●
4. Click <Search>.
●
Bookmark name : Displays the bookmark name you set.
●
Event : Displays the event type of the recorded video.
●
CH : Displays the recorded channel.
●
Time : Displays the start time and end time of the recorded video.
●
Playback : Plays the recorded video with an instant viewer.
●
Bookmark : Displays whether bookmarks are specified.
Virtual line (
) : Detects the passing of an object based on the virtual line and direction set on the image. Click
and drag the start and end points of the virtual line to the desired location with the mouse.
– The virtual line can be set in one direction or both directions. If you select the option of the direction of the
virtual line on both sides, it will detect all objects passing in both directions on one virtual line.
●
Region of interest (
) : Uses the entire screen as a non-detection area and specifies a specific area as a motion
detection area. Drag the mouse over the image or take a vertex to set the detection area at the desired location.
– When you set a zone, an event/object option icon will be displayed at the bottom of the zone. Click the icon to
exclude the event/object from the search.
– Intrusion (
5. If you double-click an item to play in the search list, the recorded video will be played.
– Enter (
￭ Bookmarked images will be stored without being overwritten during repeated recording. However, when the automatic deletion is set, it will be deleted
according to the set period.
￭ When the bookmark is released, the video will not be saved. If necessary, before releasing the bookmark, export the video.
￭ Up to 100 bookmarks can be specified.
) : Detects and searches for moving objects within the area set by the user.
) : Searches by detecting movement from the outside to the inside of the area set by the user.
– Exiting (
) : Searches by detecting the movement from the inside to the outside of the area set by the user.
– Person (
) : Searches for events that include people within the area set by the user.
– Vehicle (
) : Searches for events that include vehicles within the area set by the user.
– All Objects (
●
) : Searches for events that include all objects within the area set by the user.
Exclusive region (
) : Uses the entire screen as a detection area and specifies a non-detection area to exclude
detection of a specific area.
Drag the mouse over the image or take a vertex to specify the non-detection area at the desired location.
3. Set the date and time range to perform the virtual area search and click <
>.
4. When you click an item to play on the time line, the corresponding recorded video will be played.
￭ You can set up to 3 areas of interest, exclusion and virtual line.
￭ Click Delete ( ) to delete all the set areas.
English _35
• search
after Wisenet X series, you must select “Enable" in "Event setup > IVA” of the camera. For details, refer to the "Setup > Setting the Event > Event
setup" page in the Table of Contents.
AI search
If there is AI data recorded by the camera, you can search for images in various conditions such as people, faces, and
vehicles.
￭ For products that support AI search function, see page 4 “Products supporting each feature” of the Product Specification Manual.
Person Search
In the recorded data, you can search for a person by any condition you want, such as gender, top/bottom color.
Screen Layout of the AI Search
1. Select <Person search> in the <AI search> menu.
2. Select a channel to search.
￭ If you select a channel to search, you can change the channel display mode by clicking <
>. You can select a desired channel by clicking or dragging it
from the channel table, and clicking the channel in the channel list.
3. Select a date and time to search.
4. Select a detailed search option.
●
Item
Description
Menu
Click each menu to go to the corresponding menu screen.
Search menu tab
Click the menu tab to display the detailed search menu. Click Search menu to go to the corresponding Search screen.
Search conditions
You can set various search conditions, such as date/time/gender.
Search results
Export
/
Displays search results.
Exports search results to a file.
Displays the search results as a list or thumbnail.
￭ The search options you set will be saved, and click <Reset> to reset the search conditions.
￭ Double click on the desired item in the search results list to go to the play screen.
When you click Playback ( ), the video will be played in an instant viewer.
￭ You can specify a bookmark by clicking the bookmark ( ) in the search results list. You can check the specified video in the bookmark search menu.
36_ AI search
Person search options : Gender, Clothing-Top color, Clothing-Bottoms color, Bag
￭ Click the option to display the option selection window. Select the desired search option.
￭ If no details are set, all conditions will be selected and searched.
5. Select the overlap.
It will be displayed when there is overlapped data in one channel by changing the time or time zone at the selected
time.
6. Click the <Search> button.
●
CH : Displays the recorded channel.
●
Camera name : Displays the camera name.
●
Attribute : Displays the recognized search result attributes.
●
Time : Displays the start time of the recorded video.
●
Playback : Plays the recorded video with an instant viewer.
●
Bookmark : Specifies a bookmark to the recorded video.
7. If you double-click an item to play in the search list, the recorded video will be played.
Vehicle Search
From the recorded data, you can search faces according to your desired conditions such as gender and age.
You can search the vehicle by setting the vehicle type and color conditions from the recorded data.
1. Select <Face search> in the <AI search> menu.
1. Select <Vehicle search> in the <AI search> menu.
2. Select a channel to search.
2. Select a channel to search.
• AI search
Face Search
￭ If you select a channel to search, you can change the channel display mode by clicking <
>. You can select a desired channel by clicking or dragging it
from the channel table, and clicking the channel in the channel list.
￭ If you select a channel to search, you can change the channel display mode by clicking <
3. Select a date and time to search.
3. Select a date and time to search.
4. Select a detailed search option.
4. Select a detailed search option.
●
Face search options : Gender, Age, Glasses, Mask
￭ Click the option to display the option selection window. Select the desired search option.
￭ If no details are set, all conditions will be selected and searched.
>. You can select a desired channel by clicking or dragging it
from the channel table, and clicking the channel in the channel list.
●
Vehicle search options : Type, Vehicle color
￭ Click the option to display the option selection window. Select the desired search option.
￭ If no details are set, all conditions will be selected and searched.
5. Select the overlap.
It will be displayed when there is overlapped data in one channel by changing the time or time zone at the selected
time.
5. Select the overlap.
It will be displayed when there is overlapped data in one channel by changing the time or time zone at the selected
time.
6. Click the <Search> button.
6. Click the <Search> button.
●
CH : Displays the recorded channel.
●
CH : Displays the recorded channel.
●
Camera name : Displays the camera name.
●
Camera name : Displays the camera name.
●
Attribute : Displays the recognized search result attributes.
●
Attribute : Displays the recognized search result attributes.
●
Time : Displays the start time of the recorded video.
●
Time : Displays the start time of the recorded video.
●
Playback : Plays the recorded video with an instant viewer.
●
Playback : Plays the recorded video with an instant viewer.
●
Bookmark : Specifies a bookmark to the recorded video.
●
Bookmark : Specifies a bookmark to the recorded video.
7. If you double-click an item to play in the search list, the recorded video will be played.
7. If you double-click an item to play in the search list, the recorded video will be played.
English _37
AI search
LP Search
LPR SEARCH
You can search for vehicle license plates from the recorded data.
You can search for the license plate number recognized in the recorded data.
￭ LPR search is only available on recorder models that support AI recognition.
1. Select <LP search> in the <AI search> menu.
2. Select a channel to search.
￭ If you select a channel to search, you can change the channel display mode by clicking <
>. You can select a desired channel by clicking or dragging it
from the channel table, and clicking the channel in the channel list.
3. Select a date and time to search.
4. Select the overlap.
It will be displayed when there is overlapped data in one channel by changing the time or time zone at the selected
time.
5. Click the <Search> button.
●
CH : Displays the recorded channel.
●
Camera name : Displays the camera name.
●
Time : Displays the start time of the recorded video.
●
Playback : Plays the recorded video with an instant viewer.
●
Bookmark : Specifies a bookmark to the recorded video.
6. If you double-click an item to play in the search list, the recorded video will be played.
1. Select <LPR search> in the <AI search> menu.
2. Select a channel to search.
￭ If you select a channel to search, you can change the channel display mode by clicking <
>. You can select a desired channel by clicking or dragging it
from the channel table, and clicking the channel in the channel list.
3. Select a date and time to search.
4. Enter the license plate number to search.
￭ Click < > to see the search guide for license plate number.
￭ The option of license plate number entry field is only available on recorder models that support LPR search.
5. Select the overlap.
It will be displayed when there is overlapped data in one channel by changing the time or time zone at the selected
time.
6. Click the <Search> button.
●
CH : Displays the recorded channel.
●
Camera name : Displays the camera name.
●
LPR : Shows the identified license plate number.
●
Time : Displays the start time of the recorded video.
●
Playback : Plays the recorded video with an instant viewer.
●
Bookmark : Specifies a bookmark to the recorded video.
7. If you double-click an item to play in the search list, the recorded video will be played.
38_ AI search
play
You can play the recorded data and export the video you want during playback.
Item
Time line
Screen Layout of the Play
Show/Hide Channel
Full aspect ratio
Full screen
Previous/Next
Channel
Item
Move the playback position and display event data.
You can change the number of channels displayed in the time line.
￭ Up to 4 channels of time line can be displayed.
You can select the split mode.
• play
Split mode
Description
Change the video display ratio.
Display the image enlarged to full screen.
You can check the time line of the previous/next channel.
Description
You can use the video control function.
Video control
Overlap
￭
￭
￭
￭
￭
￭
: Runs a smart search by specifying an area in the video window.
: Saves the video screen as an image.
: Zooms in the selected area on the screen. It only runs on a single split screen.
: Displays the image rotated 90 degrees. (This function is not supported in some models.)
: Turns the sound on or off.
: Changes the video display ratio.
The list will be displayed according to the number of overlapped data in the same time zone.
It will appear when a video is overlapped in one channel due to time or time zone change at the selected time.
Export
You can export the video of the channel you are playing.
Filter
You can filter the event items to see the time line.
Channel
The channel and camera name will be displayed.
Playback control
Date/Time
Status
Select channel
You can control video playback.
Set the date/time.
You can check the live, recording, and network status.
You can move by selecting a channel.
English _39
play
Play Search Results
Time Line Adjustment
Play Button Name and Function
Paused state
You can move the playback position and zoom the time line in and out.
●
●
●
Click the desired play position in the time line.
The playback start position will be moved.
￭ Click the start point on the left side of the time line to move the playback position to the start point of the first video.
￭ Place your mouse over the time line to see the corresponding thumbnail of the recorded video.
Playback state
Click the time line and use the mouse wheel to zoom in or out on the time scale.
It will change in the order of 24 hours-12 hours-6 hours-3 hours-1 hour-30 minutes-15 minutes-5 minutes-1
minutes.
￭ The time line magnification of the time line will be displayed at the top right of the time line.
To see the time line previous or next zooming in, zoom in and drag the time line left or right.
Open Time Line Channel
You can display the time line of multiple channels.
Item
Previous event
Go to the previous event video.
Previous frame
Move backward one frame
Playback
●
You can click <
>, <
channels as selected.
Description
Play the video.
Next frame
Moves forward one frame or more.
Next event
Go to the next event video.
> to display 1 to 4 channels in the time line. The time line will be displayed as many
●
Click <
●
Place your mouse over the time line to see the corresponding thumbnail of the recorded video.
> to move to the previous or next channel.
Speed
Select the video playback speed.
Speed : x1/8, x1/4, x1/2, x1, x2, x4, x8, x16, x32, x64, x128, x256
It is used for reverse playback.
Fast backward
Pause
Speed : -x1/8, -x1/4, -x1/2, -x1, -x2, -x4, -x8, -x16, -x32, -x64, -x128, -x256
￭ Depending on the split screen, the maximum speed may be limited.
Pause the video.
It is used for forward playback.
Fast forward
40_ play
Speed : x1/8, x1/4, x1/2, x1, x2, x4, x8, x16, x32, x64, x128, x256
￭ Depending on the split screen, the maximum speed may be limited.
Search Results Export
You can export the search results to a file.
1. Click the <
> button.
2. Select a layout and channel to export.
• play
3. Select a start date/time and an end date/time.
￭ If you changed the time zone of the recorder, select whether to apply DST.
4. Select the overlap.
It will be displayed when there is overlapped data in one channel by changing the time or time zone at the selected
time.
5. Click <
> to select a storage device.
6. Please select a storage file type.
– SEC : You can export in your own file format that can be played directly on your PC. You can play with the viewer
included in the export folder.
￭ Click <Setup> to set a password for the exported video.
￭ If you check <Include text data>, you can save text data in the exported video.
– Recorder : You can export to a file that can be played only on the recorder.
7. Check the path to save the file to be exported. Only the file name to be saved can be changed.
8. Click <Check capacity> to check the storage capacity.
9. Click <Start>.
When the export is complete, a confirmation window will be displayed.
10. Click <OK> to exit.
￭ If you click <Stop> while exporting, the export action is canceled.
English _41
setup
Sets the camera, recording, event, device, network, and system environment.
Setting the Camera
Screen Layout of the Setup
You can access to the channel setup, camera settings, and profiles and camera password-related settings.
Setting the Channel
You can register a network camera for each channel and make connection between.
Setup > Camera > Channel setup
●
Item
Menu
Top menu list
Description
Click each menu to go to the menu screen.
Configure the settings or select a parent item to change the existing settings.
●
: Displays the camera of the corresponding channel as a list or a thumbnail.
￭ Camera searched with ONVIF does not provide previews.
Camera name : Provide a camera Name. You can enter up to 15 letters including spaces.
●
IP address : Display the IP address of a network camera.
●
Model : Show the camera model name.
●
Protocol : Show the protocol information of a registered network camera.
●
Video
Sub-menu list
Among the sub-menus of selected parent menu, select a desired item to set.
Detailed Menu
Click desired item's input field to change and enter a desired value.
– On/Off : You can turn ON/OFF the selected channel's camera. If the camera video is turned off, a blank screen
is displayed.
Apply the modified settings.
– Covert1 : Shows information other than the video of the selected channel.
For privacy protection, it does not display the video while the recording continues.
Apply
– Covert2 : Shows nothing but an empty screen while the recording continues.
￭ If the channel is set to <Covert1> or <Covert2> mode, the channel's sound is not hearable.
However, the channel's sound is recorded if its Audio setting is set to <On>, even the sound is not heard in Live mode.
●
Audio
– If set to <On>, you can turn the audio of the channel ON/OFF on the Live screen.
– If set to <Off>, the channel's audio is off on the Live screen and not recorded.
●
Status : Display the connection status.
●
Edit : You can change the connection information of the camera.
●
Upgrade : You can check the camera’s version, upgrade version, and status and upgrade it.
●
PoE output status : For products that support PoE, this shows the current status of the connected PoE.
For products that support PoE, see "Products supporting each feature" (Page 4) in the Product Specification
Manual.
￭ If you cannot register a camera after initializing the system, check the network setting. As the system is initialized and the network setting
42_ setup
is reset, the camera's network bandwidth will be different from the product's network bandwidth, so it will be impossible to register a
camera.
Registering a Network Camera Manually
1. In the <Channel setup> field, click on the <Auto detect> button.
1. In the <Channel setup> field, click on the <Manual> button.
2. <Auto detect> window appears.
2. <Manual registration> window appears.
• setup
Automatic Registration of Network Cameras
￭ Click <
> in the camera list on the live screen to automatically search and register the camera.
3. Select a camera to register in the <Searched camera> list and press the <Register> button.
You can check the selected camera in the <Camera to register> list.
￭ An already registered camera will be marked in blue in the list.
￭ If you search for the camera again or if the IP is an old IP that was not assigned by the DHCP server (such as 192.168.1.100), then press the
￭ You can register the camera manually by clicking <+> from the camera list on the live screen.
3. Select a channel and protocol used to connect to a camera.
The input items may differ depending on the selected protocol.
●
Wisenet : Wisenet camera's protocol can be used.
●
ONVIF : Means the camera supports ONVIF protocols. When connecting a camera that its name cannot be
found from the list, select <ONVIF>.
<Refresh> button to check if a new IP has been assigned.
￭ <Status> shows the camera authentication status. In the <Auth failed> state, click <
￭ Click a header at the top of the list to sort the list according to that header.
4. To change the IP address of the camera, select the desired camera from the <Camera to register> list and
press the <Change IP> button.
5. Click <Next> at the bottom of the screen to set the registered camera channel.
6. Press the <Register> button on the lower right of the screen to register the selected camera.
￭ If you register a camera using a user account—not admin account—the camera features may be limited.
￭ When you change the camera ID/password in the camera web viewer, if the camera is already registered in Recorder, you also have to
￭
￭
￭
￭
￭
￭
￭ When a camera is registered with ONVIF, if the difference in system time between the camera and recorder is 2 minutes or more, you
> to enter the camera ID and password.
change the camera ID/password information registered in Recorder.
When the camera is factory reset, it defaults to the ID and password set in "Setup > Camera > Camera password".
If the camera's ID and password have already been set, the registered information matches the ID and password set in the "Setup >
Camera > Camera password". (up to 3 sets)
Wisenet camera is registered via Wisenet protocol while a third party camera is registered via ONVIF protocol.
A device running a DHCP server should never be connected to a PoE port or a camera setup port. (e.g. router)
If your camera uses its own power supply unit, you need to manually register or auto-register the camera.
For products that support PoE, see "Products supporting each feature" (Page 4) in the Product Specification Manual.
won’t be able to register it. In this case, synchronize the camera and recorder time.
●
RTSP : Comply with RFC 2326, one of "Real Time Streaming Protocol (RTSP)" for real-time streaming.
4. If you select the <Wisenet> protocol, check options as necessary.
●
Model : Select a camera model.
– Unknown : Select when the camera model cannot be identified.
– Wisenet Camera : You can register Hanwha Techwin's cameras and encoders.
– Wisenet Multi-Channel : You can register Hanwha Techwin's multi directional cameras and multi-imager
cameras. A multi-channel camera is a camera that has multiple camera modules in one body. Autoregistering your camera to Recorder lets you register multiple channels at once. However, if you want to
manually register it, you need to register one channel at a time.
English _43
setup
●
Address type : Select an address type of the camera.
￭ The supported address type may differ depending on the type of the connected product.
If you want to check the error details of camera registration
If you failed to register a camera, the reason for the failure will be displayed.
– IPv4/IPv6 : Used to provide the IP address of the camera manually.
●
– Wisenet DDNS : This is available only if the camera is registered with the Wisenet DDNS(ddns.
hanwhasecurity.com) server. Provide the registered domain for DDNS ID.
Example) http ://ddns.hanwha-security.com/snb5000 ; provide "snb5000" for Wisenet DDNS
Connection failed due to unknown error. : This message appears if the camera has failed to be registered
due to unknown connection status.
●
Due to the camera account locking, access has failed. : When you enter a wrong ID/password 5 times to
login to the camera account, this message is displayed.
Try to log in again after 30 seconds. If the same message appears, you may need to check whether someone
has tried to access your camera account from the outside.
●
Connected successfully. : This message appears if the camera is connected successfully.
●
Incorrect model information. Provide the correct model information. : This message appears if the model
information provided for registering the camera is incorrect.
●
Authentication has failed. : This message appears if the ID or password provided for registering the camera is
incorrect.
●
Connection has failed due to excessive concurrent users. : This message appears if the concurrent user
count exceeds the upper limit.
●
Connection has failed due to incorrect HTTP port information. : This message appears if the HTTP port
number of the camera is invalid.
●
Connection has failed. Unknown connection status. : This message appears if the camera has failed to be
connected due to a unknown error.
●
User Model Modification : When registering a new camera, it is named according to the device's default if
user set the model to <Wisenet Camera>. In case if automatic registration fails, user can change the model
name of camera to be registered.
– URL : Used for URL address input.
￭ The DDNS specs supported by each camera can be checked in the user manual of the corresponding camera.
●
IP address : Provide the IP address of the camera.
●
Port : Provide the device port of the camera.
●
￭ Depending on the camera type, some device ports will not be supported.
HTTP : Provide the HTTP port of the camera.
●
ID : Provide the ID of the camera that you want to register.
●
Password : Enter the password of the camera to be registered.
●
Details : You can set the streaming mode.
5. Select <ONVIF> or <RTSP> for the protocol and enter your input for each field appears.
●
ONVIF : After selecting an IP type, set IP address, ONVIF port, ID, password, and details.
– IP type : Select the IP type of the camera.
– IP address : Enter the camera's IP address.
– ONVIF port : Enter the port number when the address type is IPv4 or IPv6.
– Channel : Enter the channel to register the camera.
– ID : Enter the camera ID.
– Password : Enter the camera password.
– Details : You can set the usage of TLS, authentication mode, and streaming mode.
●
RTSP : Set URL, ID, password, and details.
– URL : Enter your RTSP access address. For more information, see your camera user manual.
– ID : Enter the camera ID.
To edit camera profile
To change profile, refer to the “Setup > Setting the Camera > Setting the Profiles" page in the Table of
Contents.
￭ In case of Recorder, if you set 3 different profiles for live, recording and network profile, one camera will produce video streams accordingly,
having different stream formats. Especially, note that the live profile may vary depending on the used screen split mode.
￭ For cameras, if applied with one profile only, the produced frame rate is fixed as the profile specifies; if applied with multiple profiles,
produced video stream's frame rate is not guaranteed. For example, if applied with 2 profiles of 30fps, the camera may transmit streams at
20fps.
– Password : Enter the camera password.
– Details : You can set the streaming mode.
Delete Network Camera
￭ If ONVIF or RTSP protocol is selected, you can set the streaming mode in the Details section.
1. Click <Delete> in the <Channel setup> field.
–– TCP : The connection to network camera operates in the RTP over TCP mode.
–– UDP : The connection to network camera operates in the RTP over UDP mode.
–– HTTP : The connection to network camera operates in the RTP over TCP (HTTP) mode.
–– HTTPS : The connection to network camera operates in the RTP over TCP (HTTPS) mode.
44_ setup
2. When the delete window appears, select the camera channel to delete.
￭ Click <All channels> to select cameras for all channels.
3. Click <OK> to delete the camera of the selected channel.
Setting the Camera Functions
Network Camera Firmware Upgrade
You can set the camera while viewing the live video of the selected camera.
Setup > Camera > Camera setup
• setup
●
Channel : Displays channel information.
●
Model : Displays the camera model information.
●
Current version : Displays the current camera firmware version.
●
1. A camera connected to Wisenet protocols.
2. A camera connected with admin privileges.
￭ For more details on camera settings, refer to the camera user manual.
Settings and operational spec vary depending on each camera.
￭ This function is not supported in some models.
Upgrade version : Displays the firmware version to upgrade.
– Press the <
– <
●
￭ You can use this feature in the following cases :
> button to select the firmware manually within the USB.
> indicates an upgrade via a remote server.
Status : Displays the status of the ongoing upgrade (upgrading, successful, failed).
SSDR
1. Press the <Upgrade> button in the <Channel setup> field.
2. Displays the upgradeable channel list among the connected cameras.
￭
￭
￭
￭
If newer firmware exists on the remote server, the upgrade version is displayed, and the check box is automatically selected.
If you do not see the upgrade version, you can press the <
> button to get the upgrade version information from the server.
Connect a USB camera with camera firmware to the recorder and press the <
> button to check and select the firmware file in the USB.
Select a channel and press the <Apply to other channels> button to apply the firmware to other channels connected to the same model at once.
3. Check the box of the channel you want to upgrade.
4. Click the <Upgrade> button. The camera firmware upgrade starts.
￭ You can move to another menu while upgrading.
￭ You can stop the upgrade by clicking the <Stop> button during the upgrade.
￭ When the upgrade is completed, you can see the result in the popup window.
￭
￭
￭
￭
￭
￭
Firmware upgrade is available only for channels connected with the Wisenet protocol and the camera’s administrator account.
If the upgrade version is not displayed even though the camera’s firmware is out of date, check the network settings.
If there are more than 50 firmware files in the top USB folder, the file may not be scanned.
The system may reboot if USB is disconnected from the recorder during an upgrade via USB.
Video data of the channel connected to the camera to upgrade may not be recorded.
Do not format the HDD until the upgrade is complete. The upgrade may fail.
If there is a significant difference between the dark and the bright areas, increase the brightness of the dark areas
to maintain the level of brightness of the entire area.
You can set Mode, Level, and D-Range.
Backlight
You can view both bright and dark areas.
You can set Mode, WDR level, WDR black level, and WDR white level.
Exposure
You can adjust the exposure of your camera.
You can set brightness, shutter, SSNR, Sens-up, iris/lens, and AGC.
●
Brightness : Adjusts the brightness by setting the exposure value.
●
Shutter : Adjusts the brightness by controlling the camera shutter speed. If you select shutter, you can set
among the items below.
– Auto : Adjusts the brightness automatically, controlling the shutter speed of the camera.
– ESC (Electronic Shutter Control) : Adjusts the brightness automatically, controlling the shutter speed
according to the surrounding brightness.
– Manual : Adjust the brightness by manually selecting the maximum/minimum shutter speed of the camera.
– Anti-flicker : Reduces flickering in video when screen blur occurs due to different lighting and frequency of
attention. The shutter speed cannot be set when the anti-flicker frequency is selected.
English _45
setup
●
SSNR : Adjusts the brightness by reducing noise and minimizing afterimages even in dark places.
●
Sens-up : Automatically adjusts the shutter speed according to the brightness of the current light.
●
IRIS/Lens : Adjusts the brightness by automatically or manually adjusting the camera IRIS and lens.
●
AGC : Adjust the brightness by amplifying the camera's electrical signal when images are shot in the dark.
Day/Night
Setting the Profiles
Setting the Recording Profile
You can configure the video profile settings for instructing the network camera (connected to each channel) to
make recording.
You can change the mode to adjust the color and contrast.
You can set Mode, Dwell time, Negative color, Duration, Alarm input, Switching brightness, Simple focus after
Day/Night, and Activation time (color).
●
Setup > Camera > Profile setup > Record
You can select the day/night video display mode in <Mode>.
– Color : Images are always displayed in color.
– B/W : Images are always displayed in B/W
– Auto : The video will be displayed in color in normal environments and in B/W at night.
– External : Displays a color or B/W video by linking an external infrared camera to the alarm in terminal. Set
the alarm in item when selecting the <External>.
– Schedule : Controls the video output mode by directly inputting the color video activation time. Click
<Setup> and enter the activation time.
Special
You can set DIS (Digital Image Stabilization), Defog, and Defog level.
￭ You can configure the settings only for the profiles that are supported by the camera.
￭ If the profiles used for recording and network are different, camera's video feed may not comply with the frame rate as specified in the
Focus
You can adjust the focus of you camera's video.
You can set Focus, Zoom, Simple focus, and Initialize focus.
Video rotation
You can set flip/mirror modes and hallway view.
Privacy area
You can set an area to be hidden in the camera image range to protect privacy. You can select whether or not to
use the privacy setting and set up to 32 new privacy areas.
￭ With a PTZ camera, it is not possible to configure settings, and when it is permitted, the setting area may be incorrect.
46_ setup
camera.
￭ It is recommended to set the identical codec for the Record/Live/Remote profile when setting the camera profile.
●
: Displays the camera of the corresponding channel as a list or a thumbnail.
●
Camera name : Display the camera name.
●
IP address : Display the IP address of a camera.
●
Profile : You can select the recording profile for selected channel.
●
Codec : You can check the codec for selected channel.
●
Resolution : You can select the resolution for selected channel.
●
Frame rate : You can set the frame rate for selected recording profile.
●
Edit : You can add, change, and delete the camera profiles.
Setting the Live Profile
Setting the Remote Profile
You can change the live transfer settings of the network camera.
You can set the video profile transmitted to the network.
Setup > Camera > Profile setup > Live
Setup > Camera > Profile setup > Remote
• setup
●
: Displays the camera of the corresponding channel as a list or a thumbnail.
●
: Displays the camera of the corresponding channel as a list or a thumbnail.
●
Camera name : Display the camera name.
●
Camera name : Display the camera name.
●
IP address : Display the IP address of a camera.
●
IP address : Display the IP address of a camera.
●
Live replacement : You can select the live profile setup mode.
If you select <Manual> the profile setup items are enabled, and you can change settings manually.
●
Profile : Select a network profile for the connected camera.
●
Codec : Show the codec information for the selected network profile.
●
Resolution : Display the resolution for the selected network profile.
●
Frame rate : Shows the selected network profile's frame rates.
●
Edit : You can add, change, and delete the camera profiles.
– Auto : For the profile for live monitoring, a profile optimized for each split mode is displayed, along with the
‘Live4NVR' profile automatically generated at the time of the camera registration.
￭ Live4NVR profile default : H.264 800 x 600, 800 x 448 30 fps
– Manual : Live monitoring is performed with the profile selected by the user from the registered camera
profiles.
– Record : Live monitoring is performed with the profile set for recording.
●
Profile : You can set the camera profile.
●
Codec : Show the codec of the selected profile.
●
Resolution : Show the resolution of the selected profile.
●
Frame rate : Show the frame rate of the selected profile.
●
Edit : You can add, change, and delete the camera profiles.
￭ If the profiles used for network and recording are different, camera's video feed may not comply with the frame rate as specified in the
camera.
English _47
setup
Editing the Profiles
Dewarping Setup
You can change the video settings of a registered network camera for each channel.
Press the <Dewarping> button at the bottom of the <Detailed profile configuration> window to go to the
distortion correction setup popup window for each channel.
Setup > Camera > Profile setup
●
Profile : Displays the profile type.
●
Video output / Dewarp view: You can set <Video output> and <Dewarp view> for each profile type.
– Fisheye view : If you select <Fisheye view> from <Video output>, the <Fisheye view> is automatically
selected for <Dewarp view>.
●
Channel selection : You can select camera channels to change their video transmission settings.
●
Add : You can add camera profile. Click on the <Add> button to launch the addition window.
Enter the information and click on the <OK> button to add it to the list.
●
●
– Dewarp view : If you select <Dewarp view> from <Video output>, you can set <Quad view>,
<Panorama>, or <Quad view 1 - 4> for <Dewarp view>.
￭ You can select view modes supported by your camera.
Delete : You can delete the selected profile from the list.
●
Resolution : You can set the resolution of the profile.
Apply to other channels : If you select <Apply to other channels>, “Apply to other channels” confirmation
window will appear.
After selecting channels that the settings will be applied to, click on <OK> to apply them to the selected
channels.
●
Mounting mode : You can change the fisheye installation type. You can select a view mode from among
ceiling/ground/wall depending on the installation location.
●
Profile : You can check the video profile of the camera connected in the camera setup.
●
Codec : You can check the codec for the selected channel.
●
Resolution : You can change the resolution of the selected channel.
●
Frame rate : You can change the frame rate of the selected channel.
●
Bitrate control : You can change the bitrate of the selected channel.
●
Type : Displays the currently applied profile.
￭ If you change specific profile settings for each product, the frame rate's setup range may be changed.
Example) If you set the frame rate for the first profile to 30 fps, then the setting range for the second profile may be changed to 15 fps.
￭ Any settings other than codec, resolution, and frame rates can be changed in the setup menu of the camera web viewer. For camera web
viewer, refer to the "Setup Viewer > Setting the Camera > Camera Setup" page in the Table of Contents. Click <Camera webviewer>
button for connection.
￭ If you change the current profile settings, you may encounter an interrupted playback on the recording or live screen for a certain time.
￭ Changes made in your camera’s setup page will be applied immediately. But any changes made through the camera's online website, it
may take up to 3 minutes to apply the changes.
￭ Bitrate settings are not supported for ONVIF cameras.
48_ setup
￭ If there is no camera registered in the Recorder that supports fisheye view, Dewarping Setup will not be available.
How to set WiseStream
Dynamic GOV/FPS setup
Function to analyze the complexity of the video and effectively reduce the data size while maintaining the
quality. For details, refer to the camera's help or the product's user guide.
Dynamic GOV can be used to automatically change the length of GOV depending on the video condition. For
details, refer to the camera's help or the product's user guide.
Press the <WiseStream> button at the bottom of the <Detailed profile configuration> screen to go to the
WiseStream setup popup window for the channel.
At the bottom of the <Detailed profile configuration> screen, press the <Dynamic GOV & FPS> button to
open the dynamic GOV/FPS setup popup for the channel.
• setup
●
Channel : You can select the channel to set WiseStream.
●
Profile : Shows the video profile of the connected camera setting.
●
Mode : You can choose the degree of video compression. You can choose either Off, Low, Medium, or High.
●
Dynamic FPS : Automatically adjusts the frame rate (frames per second) based on the video conditions.
￭ WiseStream setup cannot be executed if there is no camera registered in Recorder that supports WiseStream.
●
Dynamic GOV
– Mode : Set the GOV length to change automatically.
– Length : Enter the maximum GOV length value to be applied when there is no motion in the video.
Minimum GOV value can be set on the camera web page.
– Range : The range of the input value of <Length> is displayed.
￭ Any profile not supported with the dynamic GOV/FPS setting is marked with '-'.
English _49
setup
Setting Camera Password
Setting the Recording
You can change the passwords of all registered cameras at once.
You can setup scheduled recording, event recording and other recording related settings.
You can register the camera’s ID and password.
Setup > Camera > Camera password
Record schedule
If you set a recording schedule for a specific date and time, the recording will start at that specific time.
Setup > Record > Record schedule
●
Password : Enter the new password for the factory default camera according to the password setting rules.
The initial password for the camera must be entered.
●
Confirm password : Input the new password again.
●
ID : Enter the ID of the camera whose ID and password are set.
●
Password : Enter the password of the camera whose ID and password are set.
￭
￭
￭
￭
When the password is in factory reset, it can be changed and managed in a batch.
If you click < >, a basic guide for password setup is displayed.
If you select <Show password>, the current password is displayed as the actual input characters.
If you check the <Change the password of all registered cameras>, the passwords of all cameras are changed with the entered
password.
￭ Up to 3 sets of camera ID with password and password can be registered.
You can use the registered camera ID/PW to automatically discover and register the camera from the "Channel setup > Auto detect"
screen.
￭ A camera password registered with ONVIF and RTSP cannot be changed.
●
Channel : Select the channel you want to set.
●
All : The entire time range (Monday through Sunday including holidays, AM 0~ PM 23) will be reserved with the
same recording schedule.
●
Apply to other channels : If you select <Apply to other channels>, “Apply to other channels” confirmation
window will appear.
After selecting channels that the settings will be applied to, click on <OK> to apply them to the selected
channels.
￭ Event recording and scheduled recording starts about 3 seconds prior to the event/schedule for guaranteed recording.
Record setting by the color
Color
)
No recording
No schedule / event recording
Green (
)
Continuous
Scheduled recording only
Event
Event recording only
Continuous/Event
Both scheduled / event recordings
Orange (
50_ setup
Description
White (
Red (
●
Function
)
)
Each press of a selected cell will cycle through <No recording>-<Continuous>-<Event>-<Continuous/
Event>.
￭ If a channel's data transfer exceeds defined allowed limit, then it may affect to other channels, and may force switching to <I-frame>
Record Setup
You can check frame rates and data transfer amount of Full Frame and Key Frame recordings for each channel,
and set the transfer limit for recordings.
Setup > Record > Record setup
Record Options
You can set recording options, such as enabling dual recording or overwrite of hard disk for repeated recording.
Setup > Record > Record options
●
●
Apply to other channels : If you select <Apply to other channels>, “Apply to other channels” confirmation
window will appear.
After selecting channels that the settings will be applied to, click on < OK> to apply them to the selected
channels.
: Displays the camera of the corresponding channel as a list or a thumbnail.
●
Camera name : Display the camera name.
●
IP address : Display the IP address of a camera.
●
Continuous recording / Event recording : Set the recording method for Continuous recording or Event
recording.
– Full frame : Records all frames fed by the camera.
●
●
– I-frame : Records only key frames fed by the camera. It depends on the camera's settings.
Frame
– Not checked (
●
Event : When an event occurs, you can set which point you will start or stop recording.
●
Retention period : If you check this option, the period list box is active, and you can set the automatic deletion
period. Specify the deletion period to delete any earlier data than the specified date. However, you can search
for data from the current time to the selected date.
– Pre : When an event occurs, recording will be started regardless of the time set.
If you set it to five seconds, recording will start at five seconds before an event occurs.
– Post : When an event occurs, recording will continue after the time set.
If you set it to five seconds, recording will continue for a further five seconds after an event is finished.
●
Audio : Specify whether to record the sound received from the camera or not.
) : If the HDD is full, this will stop recording automatically.
Beeps when recording is stopped: If <Overwrite> has not been set, this button is enabled. Specifies whether
to use beep or not when HDD recording ends.
If you check it, the beep will sound on the disk full and the recording stops.
– I-frame : Shows the amount of data for the main scene recordings.
Limit : Set the amount of data allowed for input for each channel.
) : If the HDD is full, this will overwrite the existing data and keep recording.
●
– Full frame : Shows the amount of data for all the scene recordings.
●
Overwrite : Select the recording method when the hard disk storage capacity is full.
– Checked (
– Off : No recording is made.
●
Enable dual recording : Select this if you want to record both the recording profile and remote profile at the
same time. Enabling dual recording is applied with a profile suitable for split mode during playback.
●
￭ If <Overwrite> has been set, this button is enabled.
￭ You can select a channel and set a different recording duration for each channel.
Apply to other channels : If you select <Apply to other channels>, “Apply to other channels” confirmation
window will appear. After selecting channels that the settings will be applied to, click on <OK> to apply them
to the selected channels.
￭ If you press <Retention period> when you have completed your settings, all the existing data earlier than the specified period will be
deleted automatically. If you need to keep your old data, export it first.
English _51
• setup
recording even when the channel is configured to <Full frame> recording mode. For Key Frame recording channels, the icon for limited
recording appears on the live screen's top side.
But if the sum of the limits is below the max limit, you can still receive the entire frames despite exceeding the permitted bitrates for each
channel.
￭ A channel displayed in yellow indicates that the recorded data is not being transferred from the camera and that the recording is being
performed temporarily using another profile on the camera.
Check the channel information to see the applied profile to the channel listed in yellow.
A channel displayed in orange indicates that the amount of inputted data is greater than the permitted data amount. In this case, it is
impossible to record all of the incoming frames. Instead, only part of the frames (1 or 2 frames per second) can be recorded.
To resolve this issue, you must set the permitted data amount to be greater than the amount of inputted data.
Refer to the "Live > Live screen mode > Check the camera status" page in the Table of Contents.
You can set the resolution and number of recordings for each channel when an event occurs or during a normal
recording.
setup
Setting the Event
Event setup
You can set the event-related settings such as whether or not an event is detected for each channel and whether an
alarm occurs.
Sets whether or not to detect events (e.g. object detection, AI recognition, motion detection, intelligent video
analytics, tampering) sent by the camera for each channel and applies detailed settings.
AI function setup guide
To use AI function, set any of the following options as necessary : See the relevant page for detailed setup method.
–– Setup > Event > AI engine
–– Setup > Event > Event setup > Object
–– Setup > Event > Event setup > AI recognition
–– Setup > Event > Event setup > Mask
–– Setup > Event > Event setup > IVA
Setup > Event > Event setup
●
Object : You can set detailed settings for object detection of the connected camera.
●
AI recognition : Sets detailed settings for AI detection of the connected camera.
●
Mask : Sets detailed settings for mask detection of the connected camera.
●
Motion : You can set detailed motion detection for the connected camera.
●
IVA : You can set up intelligent video analytics of the connected camera.
●
Tampering : You can make detailed settings for tampering detection, such as when the screen of a connected
camera is obscured or the camera location is changed.
–– Setup > Event > Event rule setup
￭ The settings for Object detection may vary depending on the recorder model or the connection of Wisenet AI camera.
￭ AI recognition function may have different settings and operation specifications depending on the recorder model and camera.
AI engine
Object
You can set whether to use AI events (object detection, AI recognition) from the camera, and check the usage of
AI engine.
Setup > Event > Event setup > Object
Setup > Event > AI engine
●
AI engine status : Shows the AI engine usage status.
￭ If the AI engine capacity is full, no additional settings can be made. To set additional AI functions, disable the object detection and AI recognition
function from the previously set channel.
￭ If you want to use object detection and AI recognition for each channel, you can set up to 8 channels.
●
Camera name : Display the camera name.
●
IP address : Display the IP address of a camera.
●
Type : Displays the camera type.
●
Object detection : Sets whether or not to enable object detection for the camera.
●
●
AI recognition : Sets whether or not to enable AI recognition function for the camera.
￭ AI recognition works only when the object detection option is set to <Enable>.
Usage : Shows the AI engine usage of the camera.
￭ The AI engine function is only available on products that support AI. For products that support AI search function, see "Supported
products by function (Page 4)" in the product specification manual.
52_ setup
●
Object detection : You can set whether to enable object detection.
●
Object type : You can select the object type to detect.
●
●
●
●
￭ Object items may vary depending on the camera model.
BestShot : You can set the object to display the bestshot items.
￭ Set the same as the item selected in <Object type> to display the best shot when an event is detected.
Detection excluded area : You can set the exclusion area for AI object detection. Click <Add> to set the
detection exclusion area on the preview screen.
Sensitivity : Sets the object detection sensitivity.
￭ Setting the sensitivity level high increases the object detection rate but also raises the detection error rate.
Object size : You can set the size of the object to recognize the motion.
– Click <Setup> to select the minimum/maximum size and set the object size on the preview screen.
￭ If detection errors occur frequently, set the detection excluded area or lower the object detection sensitivity.
AI recognition
Motion
Setup > Event > Event setup > AI recognition
Setup > Event > Event setup > Motion
￭ AI recognition function is only available for recorder models that support AI engine function.
• setup
●
●
Motion detection : You can set whether to enable motion detection.
●
MD type : You can set a detection area and a detection excluded area.
– Detection area : Set the area to detect motion.
LPR : Sets whether or not to enable license plate number recognition.
– Detection excluded area : Set the area to not detect motion.
￭ AI recognition function may have different settings and operation specifications depending on the recorder model and camera.
￭ Clicking < > at the top right of the screen shows the AI camera setup guide.
Mask
– Add : After selecting the desired area item, set the area on the preview screen.
– Area initialization : You can clear all the set areas.
●
Object size : You can set the size of the object to recognize the motion.
●
Detection level : You can set the basic level required for motion detection. Level values can be set for each
detection area set in <MD type>. If a motion value is bigger than the set level, then a motion detection event
is triggered.
●
Detection result display : You can overlay the detection area over video.
●
Sensitivity : You can set the sensitivity of motion detection for each area. Set a lower sensitivity for an
environment where the background and an object are clearly distinguishable and a higher sensitivity for an
environment where the background and an object are not clearly distinguishable.
●
Activation time : You can set the activation time for motion detection.
– Click <Setup> to select the minimum/maximum size and set the object size on the preview screen.
Setup > Event > Event setup > Mask
– Always : Detects motion regardless of time.
– Schedule : Detect motion only during the set period. Click <Setup> to set the detection schedule.
￭ Each camera product support different features. For more information, see the camera manual or help.
●
Mask detection : Sets whether or not to use mask detection.
●
Type : You can select the mask detection type.
●
Minimum duration : Sets the minimum observation duration upon mask detection.
English _53
setup
IVA
Tampering
Setup > Event > Event setup > IVA
Setup > Event > Event setup > Tampering
●
IVA : You can set whether to enable intelligent video analytics.
●
Tampering detection : You can set whether to enable tampering detection.
●
Type : You can set a virtual line, virtual area, and detection excluded area.
●
Sensitivity : Sets the tampering detection sensitivity.
– Virtual line : Set the virtual line to enable intelligent video analytics.
– Virtual area : Set the area to enable intelligent video analytics. You can set the details of virtual areas to fit
your purposes.
￭
￭
￭
￭
Intrusion : Creates an event when the motion of an object in the designated area is detected.
Enter : Creates an event when a moving object enters into the target area from the outside.
Exiting : Creates an event when a moving object goes out of the target area.
Appear/Disappear : When an object which does not exist inside the area designated by the user appears inside the area without passing the
area line and remains for a certain period of time, or if an object which exists inside the area disappears, an event is created. You can enter the
duration to be recognized as an event.
￭ Loitering : Creates an event when the motion of a loitering object in the virtual area is detected. You can enter the duration to be recognized as
an event.
– Detection excluded area : Set the area to not enable video analytics in the virtual line and the virtual area.
– Add : After selecting the desired area item, set the area on the preview screen.
– Area initialization : You can clear all the set areas.
●
Sensitivity : You can set the motion detection sensitivity for the virtual line and the virtual area.
●
Detection result display : You can overlay the detection area over video.
●
Activation time : You can set the activation time to recognize motion analysis.
– Always : Detects motion analysis regardless of time.
– Schedule : Detects motion analysis only during the set period. Click <Setup> to set the detection schedule.
●
Object size : You can set the size of the object to recognize the motion.
– Click <Setup> to select the minimum/maximum size and set the object size on the preview screen.
●
Object : You can set the object to enable video analytics.
￭ Objects are visible only when an AI camera is connected.
￭ Object details may vary depending on the recorder model.
￭ Each camera product support different features. For more information, see the camera manual or help.
54_ setup
￭ Since tampering detection is designed for optimal performance based on the sensitivity level by the user, there may be no noticeable
change in the tampering detection performance depending on the sensitivity level under normal monitoring conditions.
Event Rule Setup
●
Event action : Displays the event action set in the event rule.
Item
You can set the event trigger and action rule to output an alarm when an event occurs.
Description
PTZ preset
Setup > Event > Event rule setup
Alarm output
• setup
E-mail
Mobile push notification
Monitor event
●
Edit : Changes the registered event rule.
Register a new event rule
●
Add : Adds a new event rule by selecting from rule creation or rule copy.
●
Delete : Deletes the selected event rule.
●
Enable : Specify whether to enable the corresponding event rule.
●
Rule name : Displays the name of the event rule. You can change the name of the event rule by clicking <
●
Schedule : Displays the schedule set in the event rule.
●
Event trigger : Displays the event trigger set in the event rule.
>.
￭ The event trigger will be displayed in the live video window when an event is received, and will be saved as an event log record.
Item
Description
Item
Description
Motion detection
SD Card
IVA
Dynamic event
Face detection
Example) DigitalAutoTracking, Queue,
ShockDetection, MaskDetection
Tampering detection
ObjectDetection
Auto tracking
Change password
Defocusing detection
HDD status
Fog detection
Fan failure
1. Click <Add> in the <Event rule setup> field.
2. Click <Create rule>.
●
Copy rule : When you select one of the event rules already created, it is added to the events list.
You can click <
> to modify the rule name.
3. Set the details when the event rule setting window is displayed.
Audio detection
Power On/Off
Sound classification
Manual recording
Alarm input (camera), Alarm input (NVR)
Recording error
Video loss detection
●
Rule name : Enter the name of the event rule.
●
Event trigger : Click <+ Add trigger> to set the event trigger and channel.
￭ Up to three event triggers can be added.
￭ The event trigger option may vary depending on the recorder model.
￭ Duration is the waiting time to recognize the occurrence of a selected event. You have to select two or more event triggers to set this option.
The event action will run only when all the selected event triggers occur within the duration time.
￭ Event triggers will be displayed on the live screen when an event occurs and are used for event log recording.
￭ To select a channel to detect an event trigger, click or drag the desired channel in the channel table. It will be displayed in orange when a
channel is selected.
English _55
setup
●
Schedule : Select the schedule to run the event action.
●
Event action : Click <+ Add action> to set the event action.
Alarm Input
– PTZ preset : Set the PTZ preset to be displayed when an event occurs. Click <
for each channel.
> to set camera presets
You can set the operation of the alarm sensor.
Setup > Event > Alarm input
– Alarm output : Set the alarm out to be generated when an event occurs. Select the output terminal
according to the number of alarm terminals on the recorder to set the alarm duration.
– E-mail : Set up users to receive e-mail when an event occurs. Click <
e-mail.
> to select users to receive the
￭ Set the interval for sending events in “Setup > Network > E-mail > Events".
– Mobile push notification : When an event occurs, the event push notification will be displayed on the
connected smart phone.
– Monitor event : When an event occurs, the screen of the corresponding channel will be displayed by
switching to the live screen. When selecting event monitoring, set the alarm duration in consideration of
network conditions.
￭ Event action will run only when all set event triggers occur. If only one of the multiple events set has occurred, the event action will not run.
￭ Set the event action only when necessary.
4. Click <OK> at the bottom of the setting window to register the event rule.
●
Type : Set the mode in which the alarm sensor will operate.
– Off : Alarm sensor is disabled. Alarm is not used.
– N.O. (Normal Open) : Sensor is opened. If the sensor is closed, it generates alarm.
– N.C. (Normal Close) : Sensor is closed. If the sensor is opened, it generates alarm.
ONVIF Setup
You can set the details related to camera events registered with the ONVIF protocol.
Setup > Event > ONVIF setup
56_ setup
●
No. : Select the channel to which the ONVIF camera is registered.
●
Camera event : It shows the list of all the events supported by a camera by using the ONVIF protocol.
●
NVR event : You can map the list of events supported by a camera to events that the Recorder can detect. There
is no default value. It only shows the value sent by a camera.
Schedule
Setting the Device
When setting the event rule, you can set the operating time of the event action.
You can make the detailed settings for devices such as storage device and monitors.
Setup > Event > Schedule
Storage Device
You can set the storage device usage and check the setting status.
• setup
Checking and formatting the device
You can check storage devices and their capacity, usage as well as status.
The connectable storage devices are HDD and USB.
Setup > Device> Storage device > Management
●
Add : Add a schedule by setting the desired day and time.
– Off : Displayed in white and no alarm will be output even if an event occurs.
– On : Displayed in orange and an alarm will be output only when an event occurs.
●
￭ Click <
> to change the schedule name.
Delete : Delete the selected schedule.
￭ You cannot delete the schedule in use.
￭ When the alarm is generated on the scheduled time, you can stop the alarm by canceling the schedule.
●
Device : Displays the storage device type.
●
No. : You can check the designated number for the built-in HDD.
●
￭ If you want the find out about the location corresponding to the HDD number, refer to the <HDD Map>.
Model : Displays the model name of the storage device.
●
Capacity : Displays the amount of storage device use and the full capacity.
●
Type : Displays the usage type of the storage device.
●
Status : Displays the current working condition of a storage device.
●
￭ If the Status is set to <Not Defined>, format the storage device before use.
Temperature : You can check the temperature of the HDD mounted in the Recorder.
●
Time : Displays the use time of an HDD.
●
Format : Select a storage device and click on format after which a format confirmation window appears.
Click on the <OK> button to format the selected storage device.
English _57
setup
●
￭ The ARB feature is available only when your video is saved in the SD card after registering your Wisenet camera using the Wisenet protocol.
Storage Status : Displays the working status of a storage device. Click the <View> to display the storage status
window.
￭
– Red : Displays the situation of video loss.
￭
– Green : Displays the normal situation without video recording losses.
– View : Click <View> to see detailed information.
￭
￭
￭
￭
￭
￭
￭
￭
￭
HDD write : Displays the current rate of recording.
Present loss : Displays the current recording loss rate.
Worst loss : Displays the maximum amount of losses up until now.
If loss is continuously generated, check the following.
For more information, refer to the "Troubleshooting (FAQ)” in the Appendix.
–– When data is lost due to system failure (reset the rate of data transferred from the camera)
–– When there is a problem in HDD recording performance due to an HDD malfunction (check the HDD error or replace the HDD)
￭
￭
￭
￭
●
Formatting will delete all the recording data that has been saved. Be careful.
While formatting is ongoing, you cannot record video.
Do not remove a formatting device until it is finished.
After installing an HDD, if the state of use of the HDD is <Not Defined>, format the HDD before use. (If the warning message persists after
formatting, replace the HDD with a new one)
ARB : Video that was not recorded due to a camera disconnection can be backed up after the connection with
the camera is re-established. Press the button and an <Auto recovery backup (ARB)> window is opened.
– Select HDD : Select a HDD to be set to ARB.
– Capacity : Shows the capacity of the HDD to be set as ARB.
– Select channel : Select a channel to run the ARB.
￭ You can select multiple channels. If you select <All channels>, all channels will be selected.
– ARB bandwidth : Select a bandwidth for the ARB function.
58_ setup
●
This is only supported in SUNAPI 2.3.2 or later.
Set the profile bitrate used for recording a video in the SD card of camera to 6144 kbps or below.
For more information on how to set the SD card recording profile, see your camera manual.
To use the ARB function correctly, both the camera and Recorder should be time synchronized with the time server.
Refer to the "Setup > Setting the System > Date/Time/Language" page in the Table of Contents.
ARB function is activated when Recorder starts/when the channel camera set is reconnected/when an Recorder recording missing section
recurs at regular intervals after Recorder starts.
Recorder recording missing section that can be restored with the ARB function is for 24 hours backwards from the point when the ARB
function is activated.
You can check which channels have ARB function activated through the message on each channel screen that is displayed when selecting
a channel.
Refer to the "Live > Live screen mode > Channel Information Display" page in the Table of Contents.
For automatically recovered files through ARB, refer to the "Search > ARB Search" page in the Table of Contents.
ARB storage capacity is recommended to be at least one day.
Example) If you saved 64 channels with 1 Mbps each, the ARB capacity should be set to 0.7 TB or higher.
HDD map : You can check the location according to the assigned number for the HDDs installed inside.
￭ Refer to this when servicing or installing an additional HDD.
￭ Do not add or remove an HDD while Recorder is running.
Connecting the iSCSI
Adding an iSCSI device
This function is only available for products that support iSCSI. For products that support iSCSI, see page 4
“Products supporting each feature” of the Product Specification Manual.
When connecting an iSCSI device to the recorder, you can search for the iSCSI device and connect and disconnect
it.
• setup
Setup > Device> Storage device > iSCSI
1. In the iSCSI window, click on the <Add> button.
2. In the <Add iSCSI> window, enter your IP address and port number and click <Search>.
●
Add : Add an iSCSI device.
●
Delete : Delete the registered iSCSI device.
●
Model : Displays the iSCSI model name.
●
iSCSI name : It displays the name of iSCSI in compliance with the iSCSI protocol format.
●
Capacity : It displays the currently used amount/total capacity of iSCSI devices.
●
Status : Displays the status of an installed iSCSI device.
List of products supported
Promise Technology vessRAID 1740i / 1840i / 2600i 1ea JBOD 3ea / SRB-160S
3. In the <iSCSI name> list, click on a device to add.
4. After entering ID/password, click on the <Apply> button.
￭ iSCSI device requires an independent port. Use a general port instead of a camera port.
￭ When using a hub to connect an iSCSI device with recorder, make sure to use the GIGA hub and to use an independent network to save data
￭
￭
￭
￭
￭
￭
￭
￭
￭
normally.
When the Recorder is connected to an iSCSI device, if you change the iSCSI equipment setting, a problem can occur.
A HDD to be mounted in vessRAID should be listed in the RAID compatibility list.
Each volume of an iSCSI device is recommended to be 16 HDDs.
When you register an iSCSI device in the Recorder for the first time, you need to format it first.
The iSCSI lun mapping function is supported.
If you activate the LUN mapping function in the iSCSI device, the LUN can only be connected to a Recorder which is mapped.
More than one mapped lun should be available to connect to the initiator when using lun mapping.
An internal HDD must be mounted in the Recorder before connecting the iSCSI device.
For the stable communication of large data, register only one iSCSI device to Recorder to use it.
English _59
setup
RAID mode setting
This function is only available for products that support RAID. For products that support RAID, see page 4
“Products supporting each feature” of the Product Specification Manual.
●
Model : Displays the registered RAID model.
●
Status : Displays the current operating condition of the HDDs installed in a RAID.
– Active : Displays that the HDD is operating normally.
– Faulty : It displays that the HDD is malfunctioning. You need to immediately replace the HDD for smooth
recovery of the RAID.
If you enable the RAID (Redundant Array of Independent Disks) mode, you can safely recover your data even if
your system HDD is damaged.
●
– Check : A problem occurs on the HDD, requiring replacement or inspection.
RAID for each product
– Ready : If recovery of 2 HDDs is required in the RAID 6 state, HDDs for which rebuild is pending are displayed.
Product
RAID type
RAID level 5 and 6 are supported.
￭ RAID level 5 : You can recover the operation and data of only one malfunctioning HDD out of all the HDDs in the
RAID array.
32-channel model
64-channel model
￭ RAID level 6 : You can recover the operation and data of two malfunctioning HDDs out of all the HDDs in the RAID
array.
￭ You can configure two arrays of RAIDs for the product. The first RAID array only uses HDDs mounted in Slot 1 to 8
while the second RAID array only uses HDDs mounted in Slot 9 to 16.
￭ You can configure an RAID array when the RAID array to be configured has 6 to 8 HDDs mounted in it.
Setup > Device> Storage device > RAID
●
RAID status : Displays the operational status of the RAID.
– Active : Signals the fact that the RAID is operating normally.
– Degraded : It is displayed when the one or more HDDs that make up the RAID are malfunctioning. When the
maximum number of HDDs allowed in the RAID level are malfunctioning, if an additional HDD malfunctions,
you cannot use or restore the RAID. Immediately, replace the HDD and proceed with restoration.
￭ For more information about how to replace the HDD and recover the RAID array, refer to the "Setup > Setting the Device > Storage device"
page in the Table of Contents.
– Rebuilding : Indicates that the RAID array is in the recovery process. At RAID level 5 or 6, if the max number
of HDDs allowed by the RAID level is malfunctioning, and one more HDD caused malfunction during
rebuilding, then you cannot recover or use the RAID array.
– Fail : This means that the RAID cannot be used or restored.
60_ setup
●
Capacity : It shows the total capacity of the HDDs that composes a RAID.
●
Temperature : You can check the temperature of HDD(s) that compose a RAID.
RAID mode setting
Distributed Recording
1. Click on the <Enable> or <Setup> button.
This function is only available for products that support distributed recording. For products that support
distributed recording, see page 4 “Products supporting each feature” of the Product Specification Manual.
2. In the use RAID window, select settings of RAID and click on the < OK> button.
●
Enable : You can select whether or not to use the RAID mode.
●
Shows the RAID types supported by each product.
32-channel model
64-channel model
Setup > Device > Storage device > Distributed recording
• setup
Product
You can save recordings in a distributed manner by distributing HDD(s) of each group.
RAID type
Level 5, level 6
3. It will show the list of HDDs that compose a RAID. In the RAID screen, click on <OK>.
4. The data deletion and system rebooting message window will appear. You can click on the <OK> button to
reboot the system for RAID mode setting.
5. When RAID building is complete, select "Setup > Device > Storage device > RAID” to check the build.
￭ If you disable the RAID mode at RAID level 5 or 6, then every RAID array will be canceled. If you want to cancel only one of RAID arrays in
￭
￭
￭
￭
use, then go to the setup window and disable that specific RAID array.
If the Status of HDD is displayed as Check or Replace under <Management>, you cannot use it when configuring RAID.
When the RAID mode is in use, it is recommended to use HDDs with the same storage space from the same manufacturer.
If you enable or disable the RAID mode, existing data will be deleted. If you need to keep your old data, export it first.
RAID Array capacity calculation
–– When you build the RAID in level 5, the available capacity of a RAID is (the least HDD capacity) x (total number of HDDs -1).
●
Record type : Select a storage type from <Continuous recording> or <Distributed recording>.
●
Initialization : Settings that are provided when <Distributed recording> is selected are configured as the
default settings.
●
Group : Select a group to distribute the recording. If you select a group, a list to select a camera to assign opens
below.
●
HDD : The number and kind of currently available HDDs are activated.
–– When you build the RAID in level 6, the available capacity of a RAID is (the least HDD capacity) x (total number of HDDs -2).
￭ If you use HDDs with different capacity, the HDD with the smallest capacity will be used to build a RAID.
Recovering RAID Array
1. If the HDD number whose <Status> is shown as Faulty or Check is recognized, check the location of HDD to
be replaced on the HDD map.
2. Replace the malfunctioning HDD from the recorder with a new HDD.
3. When the recovery starts, the LED of the replaced hard disk lights up in yellow.
In the "Setup > Device > Storage device > RAID" menu, you can check the recovery progress.
￭ Replace it with the same model of HDD or an HDD of the same capacity from the same manufacturer.
￭ A HDD used to build the RAID should be one of the recommended models.
If it's not possible to use the same model of HDD, then use the HDD with the same capacity from the same manufacturer should be used.
￭ If you remove the power cord while using the RAID, it can damage it, so be careful.
For reliable power, it is recommended you use the UPS.
￭ A new HDD to be replaced should be one that is not RAID configured.
: Update values such as hard disk capacity, input, and storage date to the latest data.
●
￭ Example) A channel number that is activated like <
> is an available HDD.
●
External : Select an external storage device on which recordings will be stored.
●
Capacity : Displays the currently used capacity and entire capacity of an HDD that is selected in the group.
●
Receive : Displays the recording data volume of a channel selected in the group.
●
●
●
￭ If the input value exceeds 200 Mbps, it will be displayed in red.
Days : Displays the number of storable days for the input from the selected channel in the group on the HDD.
￭ Example) 3 days and 12 hours is displayed as 3.5.
HDD map : You can check the location according to the assigned number for the HDDs installed inside.
Channel list : The button state of the channel list is as follows.
–
: Channel selected in the current group.
–
: Channel selected in other group.
–
: Channel that is not currently selected. Please add this channel to the group.
￭ Recording cannot be performed while saving changes in distributed recording settings.
￭ To add more HDDs for distributed recording, install them in the order of 1, 5, 2, 6, 3, 7, 4 and 8.
English _61
setup
S.M.A.R.T
Monitor
You can check the connection status and details of the hard disk mounted in the recorder.
You can set the information displayed on the monitor as well as the output system.
Setup > Device> Storage device > S.M.A.R.T
Setup > Device > Monitor
Monitor settings
You can set the monitor output related screen displays, switching time, video display, etc.
●
OSD : Only checked items among date, time, channel name and information icon will be displayed on the
monitor screen.
●
Multiple displays : Set the video display resolution.
For products that support the extended monitor, you can set the resolution after selecting <Duplicate these
displays> or <Extend these displays> mode for video display.
– Duplicate these displays : You can set the video display resolution of the primary monitor and secondary
monitor to be the same.
If you set a resolution exceeding 1920 x 1080 while operating in clone mode, the video will not be displayed
to the secondary monitor.
– Extend these displays : You can set the video display resolution of the primary monitor and secondary
monitor respectively.
￭ Primary monitor supports 4K resolution (or 1080p), and Secondary monitor supports 1080p resolution.
￭ If the newly selected resolution does not fit with the monitor, the display won’t function properly. In this case, wait until the native
resolution is restored and then switch to another resolution of your choice.
￭ The video output for Primary monitor and Secondary monitor may differ depending on the recorder model.
–– Primary monitor: HDMI
–– Secondary monitor: HDMI or VGA
62_ setup
Extended monitor setting
Screen position setup
This function is only available for products that support the use of an extended monitor.
Some monitors many not display information (camera name, icon, time information, etc.) about the Recording,
depending on the condition. Then, you can change the display position of the data.
For products that support extended monitor, see page 4 “Products supporting each feature” of the Product
Specification Manual.
• setup
1. From the monitor setup menu, select <Screen position setup>.
1. Select <Extend these displays> for video display and click <Setup>. You can change the layout of the
extended monitor.
2. Select the Screen division you want.
3. Select as many channels from the channel table as the selected number of Screen division channels to view
the videos on the monitor screen.
2. Using <
> button to adjust the screen that is cut off.
3. Click <OK>.
￭ This product only supports 30Hz at 4K resolution.
￭ When extended mode is selected, the maximum resolution of the image output on the primary monitor (HDMI) is limited to 1920 x 1080.
￭ If the newly selected resolution does not fit with the monitor, the display won’t function properly. In this case, wait until the native
resolution is restored and then switch to another resolution of your choice.
￭ Set up Event Display and Sequence Switching Time in consideration of the network environment time.
￭ The profile used in the live output of the expanded monitor uses a remote profile. If the user changes the remote profile, the video output
of the expanded monitor may be affected.
￭ If the monitor is in clone mode, you can specify up to the split mode supported by the recorder. When the monitor is set to extended mode,
you can split the screen of the Secondary monitor up to 36-split mode depending on the recorder model.
English _63
setup
Text
Registering a Text Device
You can set the POS device setting to send text information and text event information.
Device Settings
You can make detailed settings for the POS device connected to the recorder.
Setup > Device > Text > Device
●
Device : Displays the text device name registered by the user.
●
Enable : Specifies whether to enable text device.
●
Channel : Select a channel to add a device from a channel table.
●
Port : Display a port number that is set.
●
Encoding type : Select an encoding type to use from a list.
￭ Epson, Wincor Nixdorf, Axiohom, Radiant System, IBM POS device, and ANPR protocols are supported.
￭ POS device connected to Recorder uses TCP/IP communication protocol.
1. Click the desired item in the text device list.
2. Enter the device information to register in the <Modify the text device> window.
●
Device name : Enter the desired text device name.
●
Text device : Specify whether to enable text device.
●
CH : Select a channel to add a device from a channel table.
●
Pre-event playback time : Enter the start time of the playback from how many seconds before when an event
occurs.
●
Port : Enter the device's port number.
●
Encoding type : Select the encoding type of the device.
●
Device type : Select the device type.
●
Start / End : You can select starting and ending character strings.
– A text string can be entered by using texts, hex codes, and regular expressions.
– Text : Enter a text string to search for.
– Hex Code : Enter a hexadecimal text string to search for.
(Your input should not be in hexadecimal —e.g. 1b40, 1b69)
– Regular expression : Enter a regular expression to search for text strings that follow specific rules.
3. Click <OK>.
64_ setup
Text Event Settings
Setting the Network
You can set the text to receive an alarm when an event occurs.
You can set various network functions, such as monitoring live video by connecting to a network from a remote location
and receiving an event by e-mail.
Setup > Device > Text > Event
IP & Port
• setup
You can set the network connection route and protocol.
Setting a network connection
Sets the protocol and environment of the network.
Setup > Network > IP & Port > IP address
●
Total amount : Set the condition of the total amount to be notified when a text event occurs. Check whether
the total amount is used, and then select the base amount and range.
●
Keyword : You can register or delete keywords to be notified when an event occurs.
– If the <Add> button is clicked, a screen to add keywords pops up.
– If you select one of the added keywords to delete and click the <Delete> button, the selected keyword will
be deleted.
￭ When entering the total amount, set it to 15 characters or less, including minus and decimal point.
￭ When entering keywords, set them within 50 characters. Up to 20 keywords can be specified.
●
Network : Each product supports a different number of network ports. If it supports two or more network
ports, you can set the network for each function as follows.
●
Network 1(Camera) : It can be used as a port for connecting a camera. If you connect a camera, then the
camera video will be transmitted. Using the network information, you can access the web viewer.
●
Network 2 (Viewer) : It can be used as a common port for camera and web viewer connection.
●
Network 3 (iSCSI) : It can be used as a dedicated port for iSCSI connection.
●
￭ Only provided for products that support Network 3.
Network (All) : It can be used as a common port for connecting camera, web viewer, and iSCSI.
– IP type : Select the type of network access.
– IP address, Subnet Mask, Gateway, DNS
￭ Manual : IP address, subnet mask, gateway, and DNS can be directly entered.
￭ DHCP : IP address, subnet mask, gateway, and DNS can be automatically set.
●
Transfer bandwidth : Enter the max data volume of a rate for transfer.
●
Default gateway : Select the default gateway. If there are multiple network ports, set one of them as the default
gateway.
￭ The DNS value of DHCP can be directly entered only if you have selected <Manual>.
English _65
setup
Connecting and Setting the Network
●
Networking may differ from the connection method, check your environment before setting the connection
mode.
1. To access the Broadband Router's configurations, open a web browser on the local PC that is connected to the
Broadband Router and enter the router's address (ex : http://192.168.1.1).
When no router is used
●
Manual mode
– Internet connection : Static IP, leased line, and LAN environments allows connection between the Recorder
and remote user.
2. At this stage, make the local PC's windows network configurations to the below example :
Example) IP : 192.168.1.2
Subnet Mask : 255.255.255.0
Gateway : 192.168.1.1
– Once connected to the Broadband Router, it prompts with password. While entering nothing to the User
Name field, enter “admin” into the password field and press <OK> to access the router configurations.
– Network Settings : Set the <IP type> of the connected recorder to <Manual>.
●
￭ Consult your network manager for IP, Gateway and Subnet Mask.
– Access the router's DHCP configuration menu and set its DHCP server activation, and provide the start and
end address.
￭ Start address : 192.168.0.100
￭ End address : 192.168.0.200
DHCP mode
– Internet connection : Connect the Recorder directly to a cable modem, DHCP ADSL modem or FTTH
network.
￭ Above steps may differ from the router devices depending on the manufacturer.
– Network Settings : Set the <IP type> of the connected recorder to <DHCP>.
When a router is used
Port Setting
￭ To avoid IP address conflict with the Recorder's static IP, check followings :
●
Setting the DHCP IP Address of the Broadband Router
Setup > Network > IP & Port > Port
Setting the Recorder with a static IP
– Internet connection : Connect the recorder to an IP router where cable modem is connected, or connect the
recorder in the local area network (LAN) environment.
●
Setting the Recorder Network
1. Set the <IP type> of the connected recorder to <Manual>.
2. Check whether the set IP address is in the static IP range provided by the Broadband Router.
IP Address, Gateway, and Subnet Mask : Consult your network manager.
￭ If a DHCP server is configured with starting address (192.168.0.100) and end address (192.168.0.200), you should set the IP address out of
the configured DHCP range (192.168.0.2 ~ 192.168.0.99 and 192.168.0.201 ~ 192.168.0.254).
3. Check the Gateway address and subnet mask are equal to those set in the Broadband Router.
●
Protocol type : Select the protocol type among TCP, UDP Unicast and UDP Multicast.
●
RTSP port : It is used to transmit the video over the network. The initial value is <558>.
●
UDP port : Activated when an UDP item is selected in protocol type. The initial value is <8000-8159>,
and the setting value changes in 160 units.
– UDP : It has less stability and faster speed when compared to TCP, and recommended for local area network
(LAN) environments.
●
Multicast IP address : Enter the IP address directly when selecting an UDP Multicast.
●
Multicast TTL : Enter the TTL value when selecting an UDP Multicast. The initial value is set to <5>, and enter a
value between 0 and 255.
●
HTTP port : Enter the port value for the HTTP web viewer. The initial value is set to <80>.
●
HTTPS port : Enter the port value for the HTTPS web viewer. The initial value is set to <443>.
￭ HTTPS is an enhanced version of the HTTP web communication protocol. If security is important when accessing the web viewer, enable the HTTPS
port.
●
66_ setup
Cam proxy port : Sets the camera proxy port. The initial value is set to <10001>.
DDNS
If a remote user accesses the network, you can set whether or not to use DDNS and the site to be connected.
Setup > Network > DDNS
To check Quick Connect status
A progress bar and its message appears for a Quick Connect.
Quick Connect Success : Message for a successful connection.
●
Invalid Network Configuration : Message appears if the network configuration is not valid. Check the
configuration.
●
Please enable UPnP function of the router. : Message appears if the router requires UPnP function enabled.
●
Failed to find the router. : Message appears if the router is not found. Check the router's configurations.
●
Please restart the router. : Message appears if the router should be restarted.
DDNS Setting
Setting DDNS in the Recorder
Set <Protocol type> to <TCP> in the "Setup > Network > IP & Port > Port" menu of the connected recorder.
DDNS Settings of the Router
●
Server : Specify the use of DDNS and select a site that you registered.
●
Server name : Enter the server name registered with the DDNS site.
●
Product ID : Enter the product ID registered with the DDNS site.
●
Host name : Enter the host name registered with the DDNS site.
●
User name : Enter the user name registered with the DDNS site.
●
Password : Enter the user password registered with the DDNS site.
●
Quick connect : Appears if the <ddns.hanwha-security.com> is selected for a <Server>.
To use the function, set to <Enable> after connecting the Recorder to a UPnP router.
Select the corresponding menu for the network transfer protocol of the router.
Setting up UPnP of Router
Refer to the router's documentation to enable the UPnP function of the router.
￭ If you select <Off>, the input box will be inactive.
￭ If you select <ddns.hanwha-security.com>, the host name input box will be inactive.
￭ If you are setting up a port that is already in use, then the connection might fail. Check the port setup of your router.
￭ Server name, product ID, and quick connect can be displayed if you set <Server> to <ddns.hanwha-security.com>.
￭ DDNS is a short form of Dynamic Domain Naming System.
DNS (Domain Name System) is a service that routes a domain name consisting of user friendly characters (ex : www.google.com) to an IP
address consisting of numbers (64.233.189.104).
DDNS (Dynamic DNS) is a service that registers a domain name and the floating IP address with the DDNS server so that the domain name
can be routed to the IP address even if the IP is changed in a dynamic IP system.
English _67
• setup
●
setup
IP Filtering
HTTPS
You can prepare the list of IP addresses to allow or block access to a specific IP address.
You can choose a secured connection system or install a certificate.
Setup > Network > IP filtering
●
Filtering type
Setup > Network > HTTPS
●
Secure connection system : You can select a type of security connection system.
– Deny registered IP : Access to the registered IP address will be limited.
– HTTPS ON / HTTP ON
– Allow registered IP : Only registered IP addresses can be accessed.
– HTTPS ON / HTTP OFF
●
Enable : Select whether to enable registered IP filtering.
– HTTPS OFF / HTTP ON
●
IP address : Displays the registered IP address. Double click the IP address to change the settings.
– HTTPS OFF / HTTP OFF (Alert)
●
Prefix : Displays the prefix to be filtered. Double-click the prefix to change the settings.
●
Filtering range : If you enter an IP address or prefix, then the range of IP addresses blocked or permitted will be
displayed.
￭ If a camera's IP address is not included in the Permit list or is in the Reject list access to it will be rejected.
￭ For IPv4, camera IP filtering through PoE port is not immediately applied. (Previous connections are maintained, and filtering is applied on
next login.)
To register the IP addresses to filter
1. Select the IP type tab you want to register from IPv4 or IPv6.
2. Click <Add> at the bottom of the screen.
3. When the additional window is displayed, set the details.
●
IP filtering : Select whether to enable IP filtering.
●
IP address : Enter the address to enable IP filtering.
– When entering an IP address, a value in the range 0-255 must be entered to register.
●
Prefix : Enter the prefix value.
4. Click <OK> to complete.
￭ To delete a registered item, select the check box of the item to be deleted and click <Delete> at the bottom of the screen.
68_ setup
￭ If the recorder is connected to the external internet or installed in an environment with high priority for security, making a secure
connection is recommended.
●
●
Certificates : You can select the type of certificate from <Private certificate> or <Public certificate>.
￭ <Public certificate> can be selected only when there is a registered public certificate.
Install a public certificate : You can scan and register a public certificate to be installed. To install a certificate,
you must install a certificate file or key file issued by a certificate authority. Click <Install> to register the
certificate.
802.1x
E-mail
When connecting to a network, you can select whether to use the 802.1x protocol and install a corresponding
certificate.
You can send an e-mail to a Recorder-registered user at a specific time interval, or if an event occurs.
802.1x is an authentication system between a server and a client, which prevents hacking, virus infection, and
information leakage of transmitted and received network data.
SMTP Setting
Sets the SMTP mail server.
• setup
802.1x can be used to block the unauthorized client access and increase security by allowing only authenticated
users to communicate.
Setup > Network > E-mail > SMTP
Setup > Network > 802.1x
●
●
●
●
EAPOL version : Select the EAPOL version to be used as protocol.
￭ Some switch hubs will not operate if you set them to version <2>. Select the version <1>, which is the EAPOL default.
●
Server address : Enter the SMTP server address to connect to.
●
Port : Enter the connection port.
●
Enable authentication : Check this if the SMTP server uses user authentication.
The ID and password fields will be activated when the authentication is enabled.
ID : Enter the ID provided by the RADIUS server administrator.
￭ If the entered ID does not match the ID of the client's certificate, it won't be processed properly.
Password : Enter the password provided by the RADIUS server administrator.
￭ If the password you entered does not match that of the client's private key, it won't be processed properly.
Certificates : Search for a device. Click on <
> to search for a device again.
●
CA certificates : Select this only if your public certificate includes the public key.
●
Client certificate : Select if the public certificate includes a client's authentication key.
●
Client private key : Select it if the public certificate contains the client private key.
– ID : Enter a ID to use authentication when connecting to the SMTP server.
– Password : Enter the password of the SMTP server user.
●
Enable Transport Layer Security (TLS) : Select one from <Never> and <TLS (if available)>.
●
Sender : Use the virtual keyboard to enter the sender's e-mail address.
●
Test e-mail : Conducts the test on the server settings.
￭ For successful implementation of the 802.1x operating environment, the administrator must use the RADIUS server.
In addition, the switch hub connected to the server must be a device that supports 802.1x.
￭ If the time setting of the RADIUS server, the switch hub and an recorder do not match, communication between them can fail.
￭ If a password is assigned to the client's private key, the server administrator should confirm the ID and password.
The ID and password allow up to 30 characters each. (But it only supports letters, numbers and special characters ("-", "_", ".” 3 types) only.
Accessing non password-protected files is allowed without entering a password.
￭ The 802.1x protocol adopted by the Recorder is EAP-TLS.
￭ You need to install all three certificates to use 802.1x.
English _69
setup
Event Setting
SNMP
You can set the interval and type of the event that will be sent to the user.
The SNMP protocol allows system or network administrators to remotely monitor and configure the network
devices.
Setup > Network > E-mail > Event
Setup > Network > SNMP
●
Delivery interval : Set the event interval.
￭ If a series of events occurs, the e-mail will be sent at the specified interval, not on each event.
●
●
Recipient Setting
Enable SNMP v1 : SNMP v1 is used.
Enable SNMP v2c : SNMP v2c is used.
– Read community : Enter the name of read-only community to access the SNMP information. By default it is
set to <public>.
You can create a group and add users to it or; you can delete users and change a group.
– Write community : Enter the name of write-only community to access the SNMP information. By default, it is
set to <private>.
Setup > Network > E-mail > Recipient
●
Enable SNMP v3 : SNMP v3 is used.
– Password : Set the initial user password for SNMP version 3.
●
Enable SNMP traps : SNMP trap is used to send important events and conditions to the Admin System.
– IP address : Enter the IP address to which messages will be sent.
●
Click on <
> to add a group.
Enter the group name.
●
Select a recipient group to receive emails.
If a group is added, it will appear in the group list.
●
Click on <
> to add a recipient.
Select a group and enter names and email addresses.
If a group is created, you can add a recipient.
70_ setup
DHCP Server
Checking the status
You can set the internal DHCP server and assign an IP address to the network camera.
You can check the IP address assigned to the current DHCP server, MAC address, and the connected network port
information.
Network Setting
Setup > Network > DHCP server > Status
●
Network : You can set the IP range and time to activate as the recorder's DHCP server.
• setup
Setup > Network > DHCP server > Network
Failover
To set the DHCP server
This function is only available for products that support failover. For products that support failover, see page 4
“Products supporting each feature” of the Product Specification Manual.
1. Click <Setup> of the network you want to set as a server.
If the recorder cannot record due to a network failure, other recorders that have been prepared can record
instead.
2. When the network setting window is displayed, select <Run> for <Status>.
You can connect 32 'Active' recorders to one 'Standby' recorder.
3. Enter the starting IP and end IP in the <IP range> field.
4. Fill in the <IP lease time> field.
5. Click <OK>.
The IP range entered is set as the DHCP server address of the network.
￭
￭
￭
￭
The recorder you want to configure for failover needs to be connected to both the camera and viewer ports to the local network.
Failover configurations can only be set with recorders of the same model.
Troubleshooting network interface supports IPv4 only.
All recorders must have time synchronized. For more information about time synchronization settings, refer to the “Setup > Setting the
System > Date/Time/Language" page in the Table of Contents.
￭ The network IP band in the recorder must be set to a different band.
–– Example of IP in a different bandwidth
Example 1) IP : 192.168.1.200, subnet 255.255.255.0
In the Example 1) above, since 255 of the subnet corresponds to 192.168.1, any IP in a format of 192.168.1.x has the same bandwidth.
An IP in a format of 192.168.2.x has a different bandwidth with an IP in a format of 192.168.1.x.
Example 2) IP : 172.16.1.200, subnet 255.255.0.0
In the Example 2) above, since 255 of the subnet corresponds to 172.16, any IP in a format of 172.16.x.x has the same bandwidth.
An IP in a format of 172.17.x.x has a different bandwidth with an IP in a format of 172.16.x.x.
￭ For more information about network settings, refer to the “Setup > Setting the Network" page in the table of contents.
English _71
setup
To set troubleshooting
1. Set one recorder to <Standby> mode and the other recorder to <Active> mode.
2. In the recorder set to <Active> mode, enter the viewer port IP and administrator password of the <Standby>
recorder you want to connect to and click <Connection> under the status display.
3. Check the IP and status of the connected <Active> recorder in the <Standby> recorder.
In the case of standby mode
●
Device list & status : Shows the status of the normal recorder currently connected to the standby recorder. To
delete the normal recorder connected, click <Delete> on the right side of the recorder.
￭ The standby recorder can only enable some functions in the <System>, <Device>, and <Network> menus. You can't use the
<Record> and <Event> menus.
￭ In the standby recorder, the previous operation will stop when a failover is performed during the playback or section export, and the screen
will move to the live screen.
Setup > Network > Failover
State name
Description
Ready
Ready to be connected
Connected
Normal recorder and standby recorder connected (failover available)
Failover
Troubleshooting is being performed
Connected fail
Connection was attempted but failed
Authentication failure
●
Mode : Select either <Active> or <Standby> mode.
– Active : Recorder being recorded. Monitored by the <Standby> recorder.
– Standby : Recorder being prepared without recording. It will record instead of the <Active> recorder if a
problem occurs.
Auth failed by entering an incorrect standby password when attempting to connect
Connected(Match Time Required)
Connected without time synchronization with the standby recorder
Connected(check camera port IP)
Even if the camera port of a normal recorder is connected to the viewer port of the standby
recorder or connected to the same viewer port, the IP port of the camera port is not matching.
Connected fail(check camera port IP)
The connection from the normal recorder's camera port to the standby recorder's camera port
failed.
Connected fail (It is a different model.)
Failed connection by connecting recorders of different models.
Example of setting up failover
In the case of active mode
●
Standby recorder IP : Enter the viewer port ID of a standby recorder to access.
●
Standby recorder password : Enter the administrator password of the standby recorder.
●
Status : Displays the current connection status.
●
Connection / Disconnection : Click the button to access or disconnect the access.
– Subnet 1 ➡ Network 1 (Camera)
– Subnet 2 ➡ Network 2 (Viewer)
– Subnet 3 ➡ Network 3 (iSCSI)
Recording Stream
Failover Monitoring
Fake Recording Stream
Subnet 1
Subnet 2
Active
72_ setup
Active
Standby
P2P
Setting the System
This function is only available for products that support P2P. For products that support P2P function, see page 4
“Products supporting each feature” of the Product Specification Manual.
You can set the date, language, authority, etc. displayed when using the system, and query system information or log
information.
You can connect the recorder to Wisenet Mobile for easy use when using P2P service.
Setup > Network > P2P
Date/Time/Language
Setup > System > Date/Time/Language
●
Enable P2P : Select check box if you want to use P2P service.
●
QR Code : Scan QR code by mobile device.
To run the P2P service
1. Click <Enable P2P> to test the connection to see if the current recorder can be connected remotely.
2. When the connection is successful, search for Wisenet Mobile from the smart phone, and then install and run
it.
￭ When "Add a device > QR code” is selected, the Recorder QR code can be scanned.
●
Date : Sets the date and its format that will appear on the screen.
●
Time : Sets the time and its format that will appear on the screen.
●
Time zone : Sets the time zone of your area based on the Greenwich Mean Time (GMT).
●
3. When the QR code is scanned, the UID that can be seen in recorder is automatically opened in the mobile
viewer, and the mobile viewer can be used right away when the recorder ID and password are entered.
4. After this, it automatically connects to Recorder and can be monitored easily with a smart phone when
running Wisenet mobile app saved in the smart phone.
￭ GMT (Greenwich Mean Time) is standard World Time and the basis of world time zone.
Time sync : Specify the use of synchronization with the time server.
Click the <Setup> button to display time synchronization setup screen.
If you enable <Synchronize with NTP server>, the current time of the recorder is synchronized by the server
specified in <NTP server address>, and the time information cannot be manually changed.
– Synchronize with NTP server : Specify the use of synchronization with the time server.
– NTP server address : Enter an IP or URL address of the time server.
￭ P2P service period expires in 3 years. If you want to extend it after expiration, contact your vendor.
– Last sync : Displays the most recent synchronization time from the selected time server.
– Enable as NTP server : If you select <Enable>, this recorder will act as a time server for another recorder or
network camera.
●
DST : Set up Daylight Saving Time with its period to make the time earlier than the GMT of its time zone by 1
hour during the set period.
●
Language : Select your language. Sets the language for the interface.
￭ Depending on the location of the product release, the language and standard time setup may vary.
English _73
• setup
You can check and setup the current Date/Time and time related properties, as well as the language used for the
interface on the screen.
setup
●
Holiday : A user can select specific dates as holidays according to their own preferences. Select a holiday from
the calendar displayed by clicking <Setup>.
– The same applies to <Record schedule> or <Schedule> settings as holidays.
User
You can manage users, such as adding or deleting users and granting different authorities for each user.
Setting the Administrator
You can set and change Administrator's ID and password. The administrator can use and set all menu items and
functions.
Setup > System > User > Administrator
Example) If you select May 1 and check <May 1Day>, May 1 will be set as a yearly holiday, and if you check
<May 1Day> and <First Friday l May> May 1 of every year and all Fridays of the first week of May will be set as
holidays.
To use the calendar
●
ID : Change the admin ID.
●
Current PW : Enter the current PW.
●
New password : Enter new password.
●
Confirm new password : Enter the new password again.
￭ If <Show password> is selected, the password will no longer be hidden on the screen when you type it.
￭ The initial administrator ID is set to “admin” and you will need to configure the password in the installation wizard.
￭ Please change your password every three months to safely protect personal information and to prevent the damage of the information
1. Select year and month.
￭ Click < > on the right side of the year to change the year by one year.
￭ Click the < > to the right side of the month to change the month every 3 months.
2. Select a date and click on the <Apply> button.
74_ setup
theft.
Please, take note that it's a user's responsibility for the security and any other problems caused by mismanaging a password.
￭ If you click < >, a basic guide for password setup is displayed.
User setting
If you want to register a user
You can create user groups and set authorities for each group. You can manage user information such as
registering and deleting users in the created user group.
Setup > System > User > User
• setup
1. Click on the <
> button to launch the user addition popup window.
To add a user, click on <OK>.
2. Select a group.
When registering a user, the selected group will be automatically registered.
If you want to add a group
1. Click on the <
> button to launch the Group Addition popup window.
If you want to add a group, click on <OK>.
2. If you click the group name item on the right, a virtual keyboard to enter the group name will appear.
Enter the group name to register.
￭ You can add a maximum of 10 groups.
If you want to set group permission
Set the access authority of the group.
Users in the group can only enable the menu to which they have been granted authority.
￭ You can change the group after entering all the user information.
3. Enter a name, ID and password (confirm password) and enable or disable the viewer option.
If you activate use of <Viewer>, you will have the right to use the web viewer and the network viewer.
￭ If <Show password> is selected, the password will no longer be hidden on the screen when you type it.
4. Click <Apply>.
Registered user information will be saved.
When you want to delete the group and user information
1. Select the group or user to delete and press the <
> button.
2. The deletion confirmation window will appear and click on <OK>.
1. Select the menu to set group permissions.
Set the menu and click <Setup> on the right to display the detailed settings window.
●
Live channel : You can set permissions to access the live screen for each channel.
●
Search channel : You can set permissions to access the search menu for each channel.
●
Export : You can set the authority to access the export menu for each channel.
●
Menu : You can select and set the setting menu that can be accessed. A group user can only access the
menu selected. If you select the menu, the menu permission setting screen will be displayed.
●
Record, Stop recording, PTZ control, Remote alarm output control, Shutdown : You can set the menu to
grant access to users in the group.
￭ Permission-set menus will show up in the Live menu when users of the group log in.
2. Select <Apply>.
Users in the group will be given access to the set items.
English _75
setup
Restriction Settings
If the user has restricted access
Set user's restricted access or network restriction.
If a general user selects a menu to which they do not have access, an access restriction confirmation window will
be displayed. If all rights are restricted, only the accessible menu of the live screen menu will be displayed, and
only the user's own password can be changed.
Items with restrictions will require logging in for use.
Setup > System > User > Restriction settings
●
Access restriction : You can set the menu to restrict the access for user.
To change the user password
– Checked (
If you log in with the user account of a group with restricted access, you just can change your own password.
) : Restricted
￭ Only those users who were given Permission for the menu in <User> can access the menu.
– Not checked (
●
) : Accessible
Setup > System > User
￭ Regardless of the Permission settings for the menu in <User> all users can access the menu.
Remote access restriction : You can restrict remote access for users.
– All viewers : Set all users to be unable to access the network and the web viewer.
– Web viewer : Set all users to be unable to access the web viewer.
●
Auto logout : A user will be automatically logged out if there is no operation on Recorder for over set period of
time.
●
ID manual entry : In the login window, select whether to enter ID.
1. Provide the login information.
2. Select <User> in <System>.
3. Please enter your current password.
4. Provide a new password. Enter the password you want to change in the password confirmation box again.
5. Select <Apply>.
The old password will be changed to a new one.
76_ setup
System Management
To upgrade the current software version
You can check the current system version and update to a new version, export data, setting initialization, and
more.
Checking the System information
• setup
You can check the current software version and MAC address before proceeding with the upgrade.
Setup > System > System management > Product information
1. Connect a device storing the software to be updated.
￭ It may take about 10 seconds to recognize the device.
￭ Upgradeable devices include USB memory, and network device.
￭ If you want to upgrade it on the network, the product should be connected to an external network.
Upgrade via the proxy server may not be enabled due to the restricted access.
2. Select <System management> from <System> window.
●
Product information : Shows the current system's information.
3. Select <Product information>.
– Model : Shows the model name of the product.
4. When the recognized device appears, select <Upgrade>.
– Software version : The software version of the product currently being used is displayed. You can check the
software version and upgrade to the latest version.
– MAC address : Shows the Mac address of the product.
– RAID version : Shows the RAID version for products that support RAID.
– AI version : Shows the AI version of products that support AI.
– UWA version: Shows the UWA version of the product.
●
S/W Upgrade : Updates the Recorder's software up to date.
– If hard disk is unavailable or not properly connected, the software upgrades do not appear.
– Press the <
> buttons to search for the software in the USB or on the network.
– When the updating is done, it automatically restarts. Make sure to not turn off the power during upgrade.
●
Device name : You can enter a device name for your product. To differentiate multiple recorders in VMS, Device
Manager, etc., it is recommended to enter a different device name for each device.
￭
￭
￭
￭
If you connect a device in the upgrade menu window, you can press the <
> button to search for available software.
If there is an upgraded version on the network, a popup window will appear.
<Upgrade> will be activated only when there is a higher version than the current software version.
When online upgrade is enabled, you will receive a new firmware notification when your network is connected to your recorder. After enabling it,
click the <Apply> button.
5. In the <Software upgrade> window, select <OK>.
￭ While updating, it shows the progress.
6. When the updating is done, it automatically restarts.
Do not turn the power off until it finishes restarting.
￭ If “Upgrade Failed” appears, retry from the step 4. When you experience continued failure, consult the service center for assistance.
￭ The system information displayed may differ depending on the recorder model.
English _77
setup
Settings
●
You can export the information set in the recorder to a storage device and apply the same information to other
recorders.
Power down : If the power is off, the first alarm is generated. Select the <Use the alarm output no. 1 when the
device power is off> check box and click <Apply> to clear all alarms set for alarm output 1, and then selecting
alarm 1 with another alarm out will not be possible.
￭ This function is provided only for products that support alarm output.
￭ If that function is set, the first alarm-out checkbox and all alarms in the alarm setup screen are deactivated, to Off.
Setup > System > System management > Settings
￭ If you export setup information, then the data will be saved as a file in the recorder folder of your storage device.
￭ If you want to import setup information, you have to first make sure that the setup information file is located in the recorder folder of the
storage device.
Log
You can check the log information related to system, events, and export.
Checking the system log
System Log shows log and timestamp on every system start up, system shutdown, and changes on system
settings.
●
Storage device : Shows the connected storage device.
– Press the <
●
Setup > System > Log > System log
> button to view the list of storage devices.
Recorder ➡ USB : Save the information set in the recorder to a storage device.
– If you select <Export>, a confirmation window will appear. If you select <OK>, the recorder information will
be saved as a file.
●
USB ➡ Recorder : Apply the setting information stored in the storage device to the recorder.
– If you select the exclusion setting, you can import all information but the selected information.
– If you select <Import>, you can recall the setting information stored in the storage device. Select <OK> to
apply the loaded information to the recorder.
●
●
￭ The <Export> and <Import> settings can be used in the same software version only.
Factory default : Resets the product to its factory default settings. However, logs won't be reset. Anything
selected under Exclusion Setting won't be part of the factory reset.
A confirmation pop-up will appear when you press the <Reset> button. Select the <OK> button to reset the
selected items.
Camera registration method : Set the camera registration method. This function is only available for products
that support PoE. For products that support PoE, see "Products supporting each feature" (Page 4) in the
Product Specification Manual.
– Enable PnP mode: Cameras connected to the PoE port of the product will automatically be registered for
each channel in order of port number.
￭ When the camera resets to factory defaults, it defaults to the ID and password set in the "Setup > Camera > Camera password" menu.
If the camera ID and password are not set, the recorder ID and password will be set automatically.
￭ If the camera's ID and password have already been set, the information that matches the ID and password set in the "Setup > Camera > Camera
password" menu will be registered (up to 3 sets).
￭ You may change the passwords of registered cameras all at once in the "Setup > Camera > Camera password" menu.
￭ If manual mode is used, you can register cameras connected to the recorder’s PoE port and cameras connected to a separate switch in the <Channel
setup> menu. For more details on camera registration, see the "Setup > Setting the Camera > Setting the Channel” page in the Table of
Contents.
78_ setup
●
Search date : Click the Calendar icon to display the calendar window, or use the direction buttons to specify the
search period of the system log.
●
Search : Specify the date and press this button to display the search result in the log list.
●
CH : Select a channel to search.
●
Log type : When there are too many logs, you can display logs of the desired format by selecting the type.
Select the desired type and click <Apply>.
●
First page/Last page : Move to the first/last page when there are many search results.
●
Export : Save all the logged information recorded in the Recorder into the storage device.
Checking the event log
Checking the export log
You can search recorded events including alarms, camera events and video loss.
It also shows the log and its timestamp.
You can search the user who performed the export and the execution time and details (time, channel, device, file
type).
Setup > System > Log > Export log
Setup > System > Log > Event log
• setup
●
Search date : Select the date to search the event log by using the calendar window that appears when the
calendar icon is selected or by using the arrow buttons.
●
Search date : Select the date to search the export log by using the calendar window that appears when the
calendar icon is selected or by using the arrow buttons.
●
Search : Specify the date and press this button to display the search result in the log list.
●
Search : Specify the date and press this button to display the search result in the log list.
●
CH : Select a channel to search.
●
First Page/Last Page : Move to the first/last page when there are many search results.
●
Log type : When there are too many logs, you can display logs of the desired format by selecting the type.
Select the desired type and click <Apply>.
●
First page/Last page : Move to the first/last page when there are many search results.
●
Export : Save all the logged information recorded in the Recorder into the storage device.
English _79
starting web viewer
What is Web Viewer?
Connecting Web Viewer
Web Viewer is a software program with which the operator can access a remote Recorder for real-time monitoring, PTZ
control (if configured) or search.
1. Open your web browser and type the IP address or URL of Recorder into the URL address box.
2. A user with the admin permissions should provide the admin ID and password.
A registered user should provide the user ID and password.
NETWORK
Network Camera
NETWORK
Recorder
Remote PC
Product Features
●
Remote connection using the browser
●
PTZ camera control enabled
●
Split mode supported
– 2-split vertical, 2-split horizontal, 3-split, 4-split, 6-split, 1+5-split, 1+7-split, 9-split
￭ Depending on the number of channels supported by the product, the number of screen split modes may vary.
●
Takes a screenshot and saves images in PNG format
●
Record video in AVI format-compatible with popular media players. (The integrated codec is needed)
System Requirements
The following lists the minimum suggested hardware and operating system requirements needed to run the Web
Viewer.
●
Use the browser recommended by the OS.
Ex.) Microsoft recommended browser: Microsoft Edge
●
Supported browsers : Chrome, Edge, and Safari
●
Supported OS : Works on all of the Windows, Linux, and OS X environments given the platform-independent
nature of the web.
●
Tested environments : Tested and certified to run on Windows® 10 with Edge 91, Google Chrome™ 91 and Intel®
Core™ i7-7700 processor 3.60 Ghz with NVIDIA® GeForce® GTX™ 1050 or Intel™ HD Graphics 630.
●
Performance restrictions : The performance of users' CPU/GPU may impact the video playback performance of
the web viewer. The video quality may decrease depending on the settings, such as high resolution or transfer
bandwidth, when playing H.265 video in Chrome.
80_ starting web viewer
3. After you log in, the Live Viewer main screen appears.
￭ All settings are applied according to the Recorder settings.
￭ When an initial password is entered, while partially resetting to access a web viewer, a pop up window will appear that will guide the user to change the
password and when doing a whole reset to access a web viewer, a pop up window will appear that will guide the user to complete the settings for the
Install Wizard. Set a new password when a pop up window appears.
￭ If you change the web port when connecting to the Webviewer, you may fail to access since the applicable port is blocked. In this case, change the port
to a different port.
￭ Please change your password every three months to safely protect personal information and to prevent the damage of the information theft. Please,
take note that it's a user's responsibility for the security and any other problems caused by mismanaging a password.
￭ It allow s up to 10 simultaneous access including the admin and general users.
￭ Password of the admin and general users can be changed in <User> menu of the Recorder.
￭ Normal users should have set <Web viewer> under <Remote access restriction> to Use before connecting to the Web Viewer.
For details, refer to the "Setup > Setting the System > User” page in the Table of Contents.
￭ All settings are applied according to the Recorder settings.
Set the recorder password
After factory reset, the password must be set for the recorder to access the web viewer.
2. Set the camera password in factory reset on the <Camera ID/PW> screen.
If ID/PW is already set in the camera, register the ID/PW and click <Next>.
Enter the password of the admin account, and click <Login>.
• starting web viewer
￭ Click <
> to view the basic guide for setting a password. Refer to the password setup rules.
installation Wizard
As shown below, proceed through each step of the <Installation wizard>.
Install Wizard can only be accessed at factory reset. If you do not want to proceed, click <Exit>.
￭ When you complete installation using the install wizard on your recorder, the install wizard will not appear on your web viewer.
￭
￭
￭
￭
When the password is in factory reset, it can be changed and managed in a batch.
Up to 3 sets of camera ID with password and password can be registered.
You may change the passwords of registered cameras all at once in the "Setup > Camera > Camera password" menu.
You cannot change the password for cameras registered with ONVIF and RTSP.
3. Set the network connection type and the connection environment on the <Network> screen, and then click the
<Next> button.
1. In the <Language> screen, select the language and press the <Next> button.
￭ For details on network settings, refer to the "Getting Started > Installation wizard" page in the Table of Contents.
English _81
starting web viewer
4. Set the daylight saving time on the <Time zone> screen, and then click <Next>.
5. To modify the date and time on the <Date & Time> screen, select the <Modify> check box.
Set the date and time.
6. Click the <Next> button to complete the installation wizard.
82_ starting web viewer
live viewer
You can check the video from camera registered in the Recorder connected from a remote PC. Also, you can adjust the
camera and check the network transfer status.
Menu
Description
Enables the Manual recording function of the recorder.
Screen Layout of the Live Viewer
Saves the video saved in the set time of the selected channel in PC in AVI format.
• live viewer
Clears the alarm in the event list and stops the alarm at the notification display of the system status.
Displays the information on the OSD screen in the video window.
Shows the selected Channel Information.
Shows the status of all cameras connected to the recorder.
Sets the split screen of the video window.
Shows the video in actual proportions.
It changes to full screen from the current Split Mode.
To exit full screen, press the ESC key on your keyboard.
￭ MAC Safari does not support full screen.
Video window
Menu
Menu
List/Event
Camera list
Description
The ID of the connected user is displayed.
Click each menu to go to the corresponding menu screen.
●
●
You are directly connected to the Hanwha Techwin homepage (www.hanwha-security.com).
List : Select to check the camera list.
Changes the color theme of Web Viewer.
Event : Select to check the event list
The list of cameras registered in the recorder is displayed.
Event list
Shows a list of events that occurred on the camera.
Layout list
Displays the default layout and a list of created layouts.
PTZ Control
Controls the connected PTZ camera.
Shows the video of the camera connected to the recorder.
System status display
Displays the status of the system, hard disk, and network.
English _83
live viewer
Checking the System Status
Checking Camera List
The icon at the top of the screen indicates the status of the system.
Displays the camera type, status, and name registered in the recorder.
Name
Description
Live > List
Displayed when a problem occurs with the pan or recording status.
Displayed when an error occurs in the power supply.
Displayed when the amount of input data by channel exceeds the set amount of data limit.
Displayed when the hard disk is full during recording and the recording capacity is insufficient.
Displayed when the hard disk does not exist or needs to be replaced.
Displayed when there is an abnormality in RAID or cannot be used.
Displayed when RAID is being rebuilt.
￭ Only provided for products that support RAID.
Name
Channel information
Displayed when network overload occurs.
￭ It occurs in case of excessive CPU load because the reception performance is exceeded. It disappears when you modify the Delete Camera
or Set Camera to reduce the data rate.
￭ Limit the number of users remotely monitored by Web Viewer or VMS, or control the number of channels played by remote or recorder.
Displayed if the server has firmware to update.
Checking User ID
Displays the user ID and authority for the user connected to Web Viewer.
Click <Logout> to log out the logged-in user.
￭ If you are logged in with an admin account, the authority setting window will not be displayed.
84_ live viewer
Displays channel information (channel number, video window assignment, and color indication).
Displays a normal camera.
Displayed when an error occurs in the iSCSI device connection.
￭ Only provided for products that support iSCSI.
Description
Camera type
Displays a PTZ camera.
Camera status
Camera name
Displays the camera error status.
Displays the name set for the camera.
￭ If a camera connection error occurs, it is disabled in the list.
￭ The camera status display information changes according to the network connection status and settings.
Checking the All Camera Status
Network Status
You can check the status of all cameras connected to the recorder.
Click the <
> button, followed by the <Network> tab.
You can check the status of network bandwidth currently being received/transmitted.
Live Status
> button. You can check the status and transmission information of the camera connected to each
• live viewer
Click the <
channel.
￭ To change the profile setup, click the <Camera setup> button. For details on how to set up the profile, refer to the "Setup > Setting the Camera >
Setting the Profiles” page in the Table of Contents.
￭ Each product supports a different number of network ports.
PoE Status
Click the <
Record Status
Click the <
> button and then click <PoE>.
You can check the current PoE status of each port.
> button, followed by the <Record> tab.
You can check the profile, record type, frame rate (Input/Record), and bit rate (Limit/Input/Record) for each
channel.
Max> to check the current recording status and maximum recording setting value.
￭ Use <Current
￭ To change the profile setup, click the <Record Setup> button.
￭ This function is only available for products that support PoE.
English _85
live viewer
Changing the Pattern of Split Screen
Changing Overall Channel Aspect Ratio
Click the <
Video screen ratio for all channels can be changed in live split screen mode.
> button and select the desired split screen.
The selected split screen is applied to the video window.
Click <
> at the bottom of the screen. It changes to the actual proportion of the video.
If you want to go back to the previous screen ratio, click <
86_ live viewer
> again.
Full Screen Mode
Setting up the Live Layout
You can change to full screen mode, which has no top/bottom/left/right areas of the live screen.
This section outlines how to select a series of channels based on their purpose/accessibility and monitor them in a
single layout.
Click <
> at the bottom of the screen.
Live > List
• live viewer
Check Layout List
To exit the full screen, press the ESC key on the keyboard or click <
General mode
> at the bottom of the full screen mode.
Full screen mode
●
: Create a new layout.
●
: Change the channel or name of the layout.
●
: Save the changed layout.
●
: Delete the added layout.
●
/
: Open or close the layout list.
Add Layout and Set Name
1. Click the <
> button.
2. Set the name of the layout.
3. Double-click a channel to display on the layout screen from the camera list.
4. Click <
> to save the set layout.
￭ The default layout of the live viewer consists of a 4-split screen.
￭ Each layout is saved separately by the user.
English _87
live viewer
Change of Layout Channel and Name
Real-Time Event Monitoring
1. Click <
Real-time events that occurred on the camera can be checked in the live video window and event list.
> after selecting a layout.
2. Add or delete channels or rename layouts.
3. Click <
> to save the changed settings.
Delete Layout
Click <
> after selecting the layout to delete.
￭ AI events are only available for products that support AI.
￭ AI events are displayed only after setting event rules. AI event search may have different settings and operation specifications depending on the recorder
or camera.
￭ Live event monitoring can receive data on only one channel and data can be received only from the camera currently being monitored in live.
Live > Event
Event Type and Camera Settings
Set the event type and camera to be displayed in the event list.
To search for a specific event, click <
●
> to select the event type and camera to browse.
Event : Displays only selected events in the event list.
– Common event : Searches for event types that have occurred in general cameras such as motion detection
and IVA.
– AI event : Searches for AI event types such as face, person, and vehicle.
●
Camera : Displays events for the selected camera only.
￭ The Safari browser does not support this feature.
88_ live viewer
Check Event List
Event Instant Viewer
When new events occur, the list of events will be updated accordingly.
Select an event to check from the event list, and click <
occurred.
￭ The specified channels and events are displayed in the list according to the event rule setup.
For details, refer to the "Setup > Setting the Event > Event rule setup" page in the Table of Contents.
> to play the recorded video at the time the event
￭ Instant viewer can play an event video for 1 minute.
￭ For AI events, the best shot and details of the event that occurred are displayed.
• live viewer
￭ AI event recognition may have different settings and operation specifications depending on the recorder model or camera.
￭ To see AI events, set any of the following options as necessary : See the relevant page for detailed setup method.
–– Setup > Event > AI engine
–– Setup > Event > Event setup > Object
–– Setup > Event > Event setup > AI recognition
–– Setup > Event > Event setup > Mask
–– Setup > Event > Event setup > IVA
–– Setup > Event > Event rule setup
AI event
●
: Select the event type and camera.
●
/
Common event
: Open or close the Event list.
●
/
: The video is played/paused.
●
: Go to the search menu screen.
●
: Instant Viewer playback ends.
Stop Alarm Output
When an event occurs, an alarm can occur. Click <
necessary.
> at the bottom of the screen to stop the alarm output if
For details, refer to the "Setup > Setting the Event > Event rule setup" page in the Table of Contents.
English _89
live viewer
Live Screen Menu
Camera Video Control
After selecting the desired channel on the split mode, roll the mouse cursor over the screen to see the live screen menu.
By using the function icon in the video window, you can easily enable functions such as screenshot, video rotation, and
PTZ control.
The live screen menu appears differently depending on the recorder operation status or the type of the registered
camera.
￭ Each function may be restricted depending on the type of camera and the user's authority.
Capture
Select a channel to capture video and click the <
> button.
The captured image is saved as .png file in the download folder.
PC Recording
You can record video on your PC while monitoring.
1. Select the desired channel and click the <
REC REC
REC REC
REC
REC REC REC REC REC
REC REC REC REC REC REC90
90
90
90
90
90
90
90
90 90
90 90
> button to start PC recording.
> button.
2. To end the PC recording, click the <
The recording ends, and the recorded video is saved as .avi file in the download folder.
90 90
90 90
Instant Viewer
Menu
REC REC
REC 90
Description
Capture
You can take a screenshot of the selected channel.
90
90
REC REC REC REC
90REC90 90
90
90
90
PC REC
90
90 90
During monitoring, you can rewind 1 minute before playback.
Select the desired channel and click <
The Instant Viewer screen appears.
>.
90 90
Images can be saved on a PC.
90 90
Instant viewer
During monitoring, you can rewind 1 minute before playback.
Microphone
Turns the microphone on or off on your PC.
PTZ control
If the network camera connected to the selected channel supports the PTZ function, it changes to the
PTZ control mode.
Audio
Image rotation
Channel aspect ratio
Turns the audio on or off when the audio is connected.
Rotates the video to display.
Shows the video in actual proportions.
●
/
: The video is played/paused.
●
: Moves to the playback screen.
●
: Instant Viewer playback ends.
Microphone Output
You can turn the microphone of the selected channel on or off in the live screen.
Select the desired channel and click <
90_ live viewer
>.
PTZ Mode
Zoom In
You can run PTZ control of the selected channel.
You can zoom in or out using the mouse wheel.
Select the desired channel and click <
If you scroll up using the mouse wheel, the selected video screen is enlarged by 10%, and a thumbnail window is
displayed.
>.
Enters the PTZ control mode.
REC
REC
: The PTZ mode is closed.
●
90
RECREC
90
90
90
: Go to the instant90viewer.
REC
REC
90 90
: Click the Digital zoom icon and use the mouse wheel to zoom in or out on the video.
Digital zoom ends when the video screen is reduced to the original size.
●
90
REC
90 90
: Captures video of the current state.
●
REC●
REC
90 90
REC
REC
REC
￭ Scrolling up/down using the mouse wheel will zoom in/out the video screen by 10%.
￭ Digital zoom ends when the video screen is reduced to the original size.
￭ In PTZ mode, click the < > button to run digital zoom.
• live viewer
￭ Depending on the camera, the PTZ control function and speed may be different.
90 90
Adjusting the Camera Direction
When you rolls over the mouse to <
>, the 8-way key appears, and when the mouse leaves the area of the
direction key, the direction key disappears. You can fine-tune the camera direction by clicking the 8-direction key
REC
90
once. Keep
clicking the arrow keys to move in the desired direction and release the mouse to stop.
To quickly adjust the direction of the camera, click <
> and drag. The screen moves quickly in the desired
direction. You can adjust the screen movement speed according to the drag distance.
Audio
REC
REC
90
90
You can turn the sound on/off corresponding to the channel in Live mode.
Select the desired channel and click <
>.
Audio output can only be turned on90 in one channel. The audio output of other channels will be automatically
turned off.
90
￭ If you have configured the audio output settings properly but the audio or voice is not output, check if the connected network camera supports
the sound signal and if you have configured the sound settings as appropriate.
The sound icon can be displayed if the sound signal fails to output from noise.
￭ Only the channel where <Audio> is set to <On> in “Setup > Camera > Channel setup” displays the audio icon (
you can use to turn the sound on/off.
) in Live mode that
90
Image Rotation
You can rotate the live video screen.
Select the desired channel and click <
>.
Each click of the button will rotate the video 90 degrees clockwise.
English _91
live viewer
PTZ Control
Channel Aspect Ratio
You can change the aspect ratio of each channel.
Select the desired channel and click <
>.
It changes to the actual proportion of the video.
PTZ Control Menu
If the connected network camera is a PTZ camera, the <
camera channel is selected, you can control the PTZ.
> icon is displayed in the camera list. When the
Name
Description
Zoom out/Zoom in
Near/Far
You can adjust the focus manually.
Auto focus
You can adjust the focus automatically.
Preset
Set the preset position to move the camera, and then select the desired preset to move to the set
position.
Swing
Swing is a monitoring function that moves between two preset points and enables you to trace the
motion.
Group
The group function enables you to group various presets before calling them in sequence.
Tour
Monitor all the groups created by a user in turn.
Trace
Tracking remembers the trace of movements that you instructed and reproduces it for your
reference.
Set
Delete
Preset List
92_ live viewer
Activate the Zoom operation of the PTZ camera.
The preset you set is saved and displayed in the list.
Deletes the selected preset list.
Shows a list of saved presets.
Using Digital PTZ (D-PTZ) function
To delete a registered preset
1. Register a camera that supports the D-PTZ profile.
1. Click <
￭ In cameras that support the D-PTZ profile, you can use the D-PTZ function.
2. Both cameras that support general PTZ and cameras that support D-PTZ can control the live image using
some of the <PTZ control> function menus.
2. Select the preset to delete, and click <Delete>.
3. <Delete preset> window will appear, and click <OK>.
The selected preset will be deleted.
• live viewer
￭ For more information about the supported functions, please refer to the camera manual.
>.
Preset
Preset is a set of saved data specifying the locations of a PTZ camera. A single PTZ camera can save up to 300
locations.
To add a preset
1. Select the desired channel and click <
￭ The PTZ control screen appears.
>.
Running Preset
2. Use the arrow keys to adjust the camera to the point.
1. Click <
3. Click <
2. Double-click the preset you want to run from the list.
The camera lens moves to the set position.
>.
4. If you click <Set>, the <Preset setup> window will appear.
>.
Running Swing (auto pan), Group (scan), Tour, or Trace (pattern)
The running method of each function is the same as the preset operation method. For details on how to use it,
refer to the camera's user manual.
￭ Depending on the camera's capabilities, only some features may be available.
5. Click <
> to select the Preset Order to set.
6. Enter the Preset name.
7. Click <Save>.
The preset setting will be saved.
￭ If you replace a camera that saves your preset settings with a different one, you must configure the preset settings again.
English _93
live viewer
Exporting Video
You can export the recorded video by manually inputting the desired channel, date, and time.
1. Click the <
> button.
2. Select a layout to export and select the desired channel.
3. Set the start date/time and end date/time.
￭ After setting whether to enable DST or not, select the overlap. It will be displayed when there is overlapped data in one channel by changing the time or time
zone at the selected time.
4. Enter a file name to save, and then click the <OK> button.
5. When the export is complete, a confirmation window appears.
￭ The exported video is saved as .avi file in the download folder.
94_ live viewer
search viewer
You can search and play the recorded video stored in the recorder by connecting the recorder remotely.
Name
Screen Layout of the Search Viewer
Description
Turns on/off the section setup.
Saves the video of the selected channel in the designated path in AVI format.
Play adjustment
The date of the recorded video is displayed in orange, and the current date is displayed in a orange circle. Click the date
in orange to view the recorded video information on the time line.
Select a search result to open the play screen for that data.
It changes to full screen from the current Split Mode.
To exit full screen, press the ESC key on your keyboard.
￭ MAC Safari does not support full screen.
Shows the status of all cameras connected to the recorder.
Displays the information on the OSD screen in the video window.
REC
REC
REC
90
90
90REC
90
Event list
REC
90
90
REC
90
Exports the Event list to a file.
90
Name
Menu
Displays an Event list.
Description
Click each menu to go to the corresponding menu screen.
Search menu tab
Shows detailed search menu.
Select channel
Displays the search channels.
Save the current video of the selected channel into the designated path as an image file.
Turns on/off the audio connected to each channel.
The screen of the selected channel is rotated 90 degrees clockwise.
Shows the video in actual proportions.
English _95
• search viewer
Calendar
search viewer
Time Search
Text Search
You can search the recorded data by the desired date and time conditions.
You can search the data input to the POS device connected to the recorder.
￭ The time displayed will be based on the time zone and daylight saving time (DST) applied time zone, so it may be displayed differently depending on
whether the data time zone recorded at the same time and daylight saving time (DST) is applied.
1. Select <
> in the <Search> menu.
2. Select a POS device to search.
1. Select <
> in the <Search> menu.
2. Select a channel to search.
3. Select the year and month to search.
Dates with data will be shown in orange and current dates will be shown in orange circles.
4. Select a date to search from the calendar.
The first video of the searched data of the day will be displayed in the video window and the data will be displayed
in the time line.
●
Click <Today> to search for today's date. Today’s date will be selected.
●
The displayed color differs depending on the type of recording data.
– Light green : Normal recording video
– Red : Event recording video
●
: You can filter the event items to view the time line.
●
Overlapped : You may check the timeline by setting the overlapping section caused by time change.
●
The search results will be displayed in the event list. Click the desired event list to play.
96_ search viewer
3. Select the date and time to search.
4. Set the event keywords and search condition.
●
Event keyword : You can search for text with preset event keywords. For details, refer to the "Setup > Setting the
Device > Text" page in the Table of Contents.
●
Type search keyword : Enter the text you want to search.
●
Match with case sensitivity : Searches are case-sensitive when checking.
●
Match whole words : Searches for data that exactly matches the characters entered.
5. Click the <Search> button.
The search results will be displayed in the text list. if you select the desired list, you can check the recorded video and
details.
Bookmark Search
Search Results Export
You can search for bookmarked data.
Search results of events, texts and bookmarks can be exported to a file.
Example) Bookmark search result export
1. Click <
> in the search results list.
• search viewer
1. Select <
> in the <Search> menu.
2. Select a channel to search.
3. Select the date and time to search.
4. Click the <Search> button.
The bookmark search results will be displayed. Click the desired bookmark list to play.
￭ Bookmarked images will be stored without being overwritten during repeated recording. However, when the automatic deletion is set, it will be deleted
2. Select the desired list and click <OK>.
￭ The exported video is saved as .avi file in the download folder.
according to the set period.
￭ When the bookmark is released, the video will not be saved. If necessary, before releasing the bookmark, export the video.
￭ Up to 100 bookmarks can be specified.
English _97
AI search viewer
If there is AI data recorded by the camera, you can search for images in various conditions such as people, faces, and
vehicles.
￭ For products that support AI search function, see page 4 “Products supporting each feature” of the Product Specification Manual.
Person Search
In the recorded data, you can search for a person by any condition you want, such as gender, top/bottom color.
Screen Layout of the AI Search Viewer
1. Select <Person search> in the <AI search> menu.
2. Select a channel to search.
3. Select the date and time to search.
4. Select a detailed search option.
●
Name
Menu
Description
Click each menu to go to the corresponding menu screen.
Person search options : Gender, Clothing-Top color, Clothing-Bottoms color, Bag
￭ Click the option to display the option selection window. Select the desired search option.
￭ If no details are set, all conditions will be selected and searched.
5. Select the overlap.
It will be displayed when there is overlapped data in one channel by changing the time or time zone at the selected
time.
6. Click the <Search> button.
Search menu tab
Search conditions
Search results
Click the menu tab to display the detailed search menu. Click Search menu to go to the corresponding Search screen.
You can set various search conditions, such as date/time/gender.
Displays search results
Exports search results to a file.
Displays the search results as a list or thumbnail.
￭ Click <Reset> to initialize the search conditions and results.
￭ You can specify a bookmark by clicking the bookmark ( ) in the search results list. You can check the specified video in the bookmark search menu.
98_ AI search viewer
●
CH : Displays the recorded channel.
●
Camera name : Displays the camera name.
●
Attribute : Displays the recognized search result attributes.
●
Time : Displays the start time of the recorded video.
●
Instant viewer : Plays the recorded video with an instant viewer.
●
Bookmark : Specifies a bookmark to the recorded video.
7. Click <
> in the search list to display the instant viewer.
8. Click <
> to go to the playback screen.
Vehicle Search
From the recorded data, you can search faces according to your desired conditions such as gender and age.
You can search the vehicle by setting the vehicle type and color conditions from the recorded data.
1. Select <Face search> in the <AI search> menu.
1. Select <Vehicle search> in the <AI search>menu.
2. Select a channel to search.
2. Select a channel to search.
3. Select the date and time to search.
3. Select the date and time to search.
4. Select a detailed search option.
4. Select a detailed search option.
• AI search viewer
Face Search
●
Face search options : Gender, Age, Glasses, Mask
￭ Click the option to display the option selection window. Select the desired search option.
￭ If no details are set, all conditions will be selected and searched.
●
Vehicle search options : Type, Vehicle color
￭ Click the option to display the option selection window. Select the desired search option.
￭ If no details are set, all conditions will be selected and searched.
5. Select the overlap.
It will be displayed when there is overlapped data in one channel by changing the time or time zone at the selected
time.
5. Select the overlap.
It will be displayed when there is overlapped data in one channel by changing the time or time zone at the selected
time.
6. Click the <Search> button.
6. Click the <Search> button.
●
CH : Displays the recorded channel.
●
CH : Displays the recorded channel.
●
Camera name : Displays the camera name.
●
Camera name : Displays the camera name.
●
Attribute : Displays the recognized search result attributes.
●
Attribute : Displays the recognized search result attributes.
●
Time : Displays the start time of the recorded video.
●
Time : Displays the start time of the recorded video.
●
Instant viewer : Plays the recorded video with an instant viewer.
●
Instant viewer : Plays the recorded video with an instant viewer.
●
Bookmark : Specifies a bookmark to the recorded video.
●
Bookmark : Specifies a bookmark to the recorded video.
7. Click <
> in the search list to display the instant viewer.
7. Click <
> in the search list to display the instant viewer.
8. Click <
> to go to the playback screen.
8. Click <
> to go to the playback screen.
English _99
AI search viewer
LP Search
LPR SEARCH
You can search for vehicle license plates from the recorded data.
You can search for the license plate number recognized in the recorded data.
￭ LPR search is only available on recorder models that support AI recognition.
1. Select <LP search> in the <AI search> menu.
2. Select a channel to search.
3. Select the date and time to search.
4. Select the overlap.
It will be displayed when there is overlapped data in one channel by changing the time or time zone at the selected
time.
5. Click the <Search> button.
●
CH : Displays the recorded channel.
●
Camera name : Displays the camera name.
●
Time : Displays the start time of the recorded video.
●
Instant viewer : Plays the recorded video with an instant viewer.
●
Bookmark : Specifies a bookmark to the recorded video.
6. Click <
> in the search list to display the instant viewer.
7. Click <
> to go to the playback screen.
100_ AI search viewer
1. Select <LPR search> in the <AI search> menu.
2. Select a channel to search.
3. Select the date and time to search.
4. Enter the license plate number to search.
￭ Click < > to see the search guide for license plate number.
￭ The option of license plate number entry field is only available on recorder models that support LPR search.
5. Select the overlap.
It will be displayed when there is overlapped data in one channel by changing the time or time zone at the selected
time.
6. Click the <Search> button.
●
CH : Displays the recorded channel.
●
Camera name : Displays the camera name.
●
LPR : Shows the identified license plate number.
●
Time : Displays the start time of the recorded video.
●
Instant viewer : Plays the recorded video with an instant viewer.
●
Bookmark : Specifies a bookmark to the recorded video.
7. Click <
> in the search list to display the instant viewer.
8. Click <
> to go to the playback screen.
Search Results Export
Search results such as people, faces, and vehicles can be exported to a file.
Example) Person search results export
1. Click <
> in the search results list.
• AI search viewer
2. Select the desired list and click <OK>.
￭ The exported video is saved as .avi file in the download folder.
English _101
play
Play Search Results
Export Video by Section Setup
You can play the recorded data and export the video you want during playback.
You can select the desired section from the time line or search list during video playing and export it to a file.
To Adjust the Time Line
1. Click the <
> button
2. Select the start and end points of the desired section in the time line with the mouse.
You can move the playback position and zoom the time line in and out.
3. Click the <
●
●
●
> button.
Click the desired play position in the time line.
The playback start position will be moved.
￭ Click the start point on the left side of the time line to move the playback position to the start point of the first video.
￭ Place your mouse over the time line to see the corresponding thumbnail of the recorded video.
Click <
>, <
> to zoom in or out the time display magnification. When the time line is enlarged, a scroll
bar will appear at the bottom.
￭ You can use the mouse wheel over the time line to zoom in or out on the time scale.
￭ The time line magnification of the time line will be displayed at the top right of the time line.
To see the time line before or after zooming in, zoom in and drag the time line left or right.
4. Select a layout to export and select the desired channel.
5. Set the start date/time and end date/time.
6. Enter a file name to save, and then click the <OK> button.
7. When the export is complete, a confirmation window appears.
￭ While exporting, click the <Stop> button to stop the export.
102_ play
Play Button Name and Function
Paused state
• play
Playback state
Name
Description
Previous event
Go to the previous event video.
Previous frame
Move backward one frame
Playback
Play the video.
Next frame
Moves forward one frame or more.
Next event
Go to the next event video.
Speed
Select the video playback speed.
Speed : x1/8, x1/4, x1/2, x1, x2, x4, x8, x16, x32, x64, x128, x256
It is used for reverse playback.
Fast backward
Pause
Speed : -x1/8, -x1/4, -x1/2, -x1, -x2, -x4, -x8, -x16, -x32, -x64, -x128, -x256
￭ Depending on the split screen, the maximum speed may be limited.
Pause the video.
It is used for forward playback.
Fast forward
Speed : x1/8, x1/4, x1/2, x1, x2, x4, x8, x16, x32, x64, x128, x256
￭ Depending on the split screen, the maximum speed may be limited.
English _103
setup viewer
You can configure the Recorder settings remotely on the network.
Setting the Camera
Screen Layout of the Setup Viewer
You can check a list of cameras that are connected to the Recorder and configure the necessary settings.
For details, refer to the "Setup > Setting the Camera" page in the Table of Contents.
Register
You can add a network camera(s).
Setup > Camera > Register
Name
Description
Menu
Click each menu to go to the menu screen.
Channel Setup
You can configure the video settings for each channel.
Top menu list
Configure the settings or select a parent item to change the existing settings.
Sub-menu list
Among the sub-menus of selected parent menu, select a desired item to set.
Detailed Menu
Click desired item's input field to change and enter a desired value.
Ok
104_ setup viewer
Apply the modified settings.
Setup > Camera > Channel setup
Camera Setup
Profile Setup
You can change the settings of a connected network camera.
You can set the profile for a network camera.
Setup > Camera > Camera setup
Setup > Camera > Profile setup
• setup viewer
Record
You can set the recording profile for a network camera.
●
When you click the <Camera webviewer> button, a new camera web browser window is opened.
– This is not supported if the camera is connected to the RTSP protocol.
– This is not supported if the camera is connected to DDNS, URL, or MAC Address.
– It supports the version specified below or later for each Q/P/X series camera.
(QND-7010R series : 1.04, QND-7080R series : 1.02, QND-6010R series : 1.02,
QND-6070R series : 1.01, P series : 1.01)
Live
– It supports only when the camera is connected to IPv4 and is not set to HTTPS.
– When you are connecting to the camera web page on a closed network, a camera that does not support the
universal web will not be able to output an image.
You can change the live transfer settings of the network camera.
– The cam proxy port's default settings are automatically set in sequence as many as the number of channels
supported by Recorder. If you want to change the proxy port, then select the port setup menu.
– 4 channels (10001-10004), 8 channels (10001-10008), 16 channels (10001-10016),
32 channels (10001-10032), 64 channels (10001-10064)
Example) Defaults of cam proxy ports for each product
●
4-channel model : 10001-10004
●
8-channel model : 10001-10008
●
16-channel model : 10001-10016
●
32-channel model : 10001-10032
●
64-channel model : 10001-10064
– When connecting outside the closed network as shown in the figure, the port forwarding setting of the
camera proxy port is required for the router.
Internet
Network Camera
Recorder
IP router
Remote PC
– If there are multiple Recorders within the closed network, each cam proxy port should be set using a
different port.
– If DDNS and Quick Connect are enabled, port forwarding will be automatically set.
– Chrome, Edge and Safari (Mac OS) browsers are supported.
English _105
setup viewer
Remote
Setting the Recording
You can set the video profile transmitted to the network and the expansion monitor.
For details, refer to the "Setup > Setting the Recording" page in the Table of Contents.
Record Schedule
If you set a recording schedule for a specific date and time, the recording will start at that specific time.
Setup > Record > Record schedule
Camera Password
You can change the passwords of all registered cameras at once.
Setup > Camera > Camera password
Record Setup
Select a type of the normal/event recording frame rate for each channel.
Setup > Record > Record setup
106_ setup viewer
Record Options
Setting the Event
You can set the hard disk recording option.
For details, refer to the "Setup > Setting the Event" page in the Table of Contents.
￭ You can set the recording duration separately for each channel.
Setup > Record > Record options
AI engine
￭ AI engine settings are only available on recorder models that support AI recognition.
Setup > Event > AI engine
Event Setup
You can set detailed settings for each channel's event detection mode.
Setup > Event > Event setup
Object detection
You can change the AI object detection event setup.
￭ The object detection function is displayed only when connected Wisenet AI camera.
English _107
• setup viewer
You can set whether or not to use AI events (object detection, AI recognition) and check the status of AI engine
usage.
setup viewer
AI recognition
Motion detection & IVA
You can change the AI recognition event setup.
You can change the motion detection and intelligent video analytics event setup.
￭ Settings and operating specifications may differ depending on the recorder model and camera.
￭ The IVA (Intelligent Video Analytics) function can be set by accessing the camera webpage.
Mask detection
Tampering detection
You can change the mask detection event setup.
You can change the tampering detection event setup.
￭ Settings and operating specifications may differ depending on the recorder model and camera.
108_ setup viewer
Event Rule Setup
ONVIF Setup
You can set the event trigger and action rule to output an alarm when an event occurs.
You can set the camera registered with the Onvif protocol.
Setup > Event > Event rule setup
Setup > Event > ONVIF setup
• setup viewer
Alarm Input
Schedule
You can set the operation of the alarm sensor.
Whether to output an alarm can be scheduled according to the day and time.
The initial setting will be an event sync, and an alarm will be sent only when an event occurs.
Setup > Event > Alarm input
Setup > Event > Schedule
English _109
setup viewer
Setting the Device
RAID
You can check a list of devices that are connected to the Recorder and configure the necessary settings.
This function is only available for products that support RAID.
For details, refer to the "Setup > Setting the Device" page in the Table of Contents.
You can set the RAID (Redundant Array of Independent Disks) mode.
Storage Device
You can check and change the settings related to the data storage device.
Setup > Device > Storage device
Management
You can check a storage device, amount of use, type of use and status of storage device.
Distributed recording
This function is only available for products that support distributed recording.
By allocating a certain portion of HDDs to each group, you can distribute the amount of recording for optimal
saving.
●
ARB : Video that was not recorded due to disconnection from the camera can be backed up after the
connection with the camera is re-established.
Press the button and an <Auto recovery backup (ARB)> window is opened.
For details, refer to the "Setup > Setting the Device > Storage Device" page in the Table of Contents.
iSCSI
This function is only available for products that support iSCSI.
When connecting an iSCSI device to the recorder, you can search for the iSCSI device and connect and disconnect
it.
110_ setup viewer
S.M.A.R.T
Text
You can check the connection status and details of the hard disk mounted in the recorder.
You can set the POS device text display and event text settings.
Setup > Device > Text
• setup viewer
Device
Relevant values of a POS device connected to Recorder can be set.
Monitor
You can set the information displayed on the monitor as well as the output system.
Setup > Device > Monitor
Event
It is possible to set total amount conditions and keywords to display events of a POS device.
￭ If the screen does not work properly, see “Troubleshooting (FAQ)” in the Appendix.
￭ The Monitor Setup settings control the monitor connected to the Recorder.
￭ Video exceeding the resolution of 1080p will not be displayed from the secondary monitor.
English _111
setup viewer
Setting the Network
DDNS
For details, refer to the "Setup > Setting the Network" page in the Table of Contents.
You can set DDNS.
IP & Port
Setup > Network > DDNS
A remote user can access the Recorder via the network to check the current mode and the IP address.
Setup > Network > IP & Port
IP address
Specify the network connection path.
IP Filtering
You can prepare the list of IP address to allow or block accesses to a specific IP address.
Setup > Network > IP filtering
Port
You can configure the protocol related settings.
112_ setup viewer
HTTPS
E-mail
You can select a security connection system or install public certificates.
You can specify the SMTP server that sends a mail if an event occurs and set the recipient group and users.
Setup > Network > HTTPS
Setup > Network > E-mail
• setup viewer
SMTP
You can set the server that sends mails and specify if you use the authentication process.
￭ While using HTTPS, if you want to switch to HTTP, then abnormal operation can take place as the browser contains the setting values. You need
to change the URL to HTTP and reconnect or initialize the cookie setting of the browser.
802.1x
When connecting to a network, you can select whether to use the 802.1x protocol and install a corresponding
certificate.
Event
You can set the event interval and specify which events the server sends mails for.
Setup > Network > 802.1x
English _113
setup viewer
Recipient
DHCP Server
You can set groups and recipients to receive emails.
You can set the network camera IP address and check the details by setting up a DHCP server.
Setup > Network > DHCP server
Network
You can set the internal DHCP server and assign an IP address to the network camera.
SNMP
Using the SNMP protocol, the system or network administrator can remotely monitoring the network devices and
sets the environment.
Setup > Network > SNMP
Status
You can check the IP and MAC currently used through the DHCP server, and the connected network port.
114_ setup viewer
P2P
Setting the System
This function is only available for products that support P2P.
You can configure the various settings of the Recorder system.
If you want to use P2P service, check the <Enable P2P> box.
You need to scan the QR code on the screen to use the P2P service.
For details, refer to the "Setup > Setting the System" page in the Table of Contents.
Setup > Network > P2P
Date/Time/Language
Setup > System > Date/Time/Language
System Time
Set the date and time.
Time sync
Set the time synchronization.
DST
During the summer, Daylight Saving Time (DST) advances clocks one hour forwards from the standard local time
zone.
Language
Select a preferred language for the Recorder.
Holiday
A user can select specific dates as holidays according to their own preferences.
English _115
• setup viewer
You can check and setup the current Date/Time and time related properties, as well as the language used for the
interface on the screen.
setup viewer
User
Restriction settings
You can manage users, such as adding or deleting users and granting different authorities for each user.
You can set the user permission.
Setup > System > User
Administrator
You can change the admin ID or the password.
System Management
You can check the current system version and update to a new version, export data, setting initialization, and
more.
￭ ID allows alphanumeric characters only.
￭ If the admin ID is not used for access, you cannot change the ID.
￭ If the ID being used is changed, you will be automatically logged out.
User
You can add, change or remove a user or users.
116_ setup viewer
Setup > System > System management
Product information
You can see information of the current system.
Check the model name, software version, and MAC address.
You can search for a file from the recorder connected to the PC to perform an upgrade.
Settings
Event log
Using a storage device, you can apply the current configuration of Recorder to another Recorder.
The event log lists recorded events, such as sensor events, camera events, or image losses.
Press the Initialization button to return the network settings to their factory default state. Items in the
<Exception> category are excluded from the initialization.
• setup viewer
Export log
Log
You can search the user who performed the export and the execution time and details (time, channel, device, file
type).
You can check the log information related to system, events, and export.
Setup > System > Log
System log
System related log information such as system startup, system shutdown, and menu setting change can be
retrieved.
English _117
export viewer
SEC Backup Viewer
Screen Layout of the Backup Viewer
You can play a file that is backed up in the format of SEC.
Backup in SEC format produces backup data file, library file and self-executable viewer file.
If you run the backup file viewer, the backup data file will be played.
XRN-1620B2_CAM 01
Recommended System Requirements
2020-05-14 20 :54 :13
H264(1920x1080), NONE
PCs with a lower specification than the recommended below may not fully support forward/backward and
highspeed playback.
PC Specifications
Name
Minimum requirements
Recommended
CPU
Intel Pentium 2.5GHz or more
Intel i7(3.5GHz) or more
RAM
4GB or more
8GB or more
HDD
200GB or more
500GB or more
VGA memory
512MB or more
1GB or more
1280x1024 or higher
1920x1080 or higher
Display resolution
OS
Windows 7, 8, 10
Name
Description
Selects screen ratio to display.
Split screen
The screen is changed to a split screen.
Fisheye view mode
IIf <
> is pushed, it is possible to change to a fisheye installation type. It is possible to
select wall/ground/ceiling mode according to the installation place.
The fisheye view mode on the current screen can be changed independently on each split.
Digital Zoom
118_ export viewer
Enlarge the image by up to 100 times as big as the current one.
Press the Zoom In ( ) button the enlarge the image; press the Zoom Out ( ) button
to shrink the image. You can also use the slide bar (
) in the pop-up window to
zoom in/out.
Press ( ) on a size-changed video to restore the default zoom factor (100%). If you enlarge
the image by more than 200%, the enlarged area will be marked on the digital zooming
screen. Click on the marked area and move it to a desired position.
The digital zooming is applied to all backup viewer. When the digital zooming is canceled, the
video size will restore the default rate of 100%.
Name
Description
Saves the current video's image as in an image file. Supports JPEG file format.
Screen Printout
/
A toggle button. Each time you press this button, the audio output will toggle between
activated and deactivated.
• export viewer
Audio
Prints out the current screen. You should have installed the appropriate printer driver before
you can print out the screen.
You can adjust the volume level from 0 to 100.
Watermark
/
Press the button to enable file tampering detection, to detect data file forging.
Deinterlace
You can enable the De-interlace function.
Show OSD
Check the OSD checkbox to display the OSD information on the backup playback screen.
Information such as backup date, day of the week, time, model name, and channel number
will be displayed on the screen.
Maintain aspect
ratio/Full screen
Enlarge/Reduce
Timeline
Restore Timeline
Display of storage time range
Playback Control
Maintains the aspect ratio of the playback screen.
Plays the video on a full screen.
Collapses the time range that is displayed on the range bar of the storage time.
You can collapse the range bar until the overall range is shortened to 24 hours.
Enlarges the time range that is displayed on the range bar of the storage time. You can
enlarge the range bar until the overall range is extended to 1 minute.
Restores the timeline to the default.
Displays the time range of a stored video file.
You can move the gridline of the range bar to select a time point to play.
You can adjust the video playback of the timeline.
English _119
appendix
Use Joystick
Using Virtual Keyboard
The function is only available for the product that supports a joystick. For products that support joy stick, see page 4
"Products supporting each feature” of the Product Specification Manual.
The SPC-2000 joystick is operated as follows :
1. For alphanumeric inputs, the virtual keyboard window appears.
2. Using a mouse, click on the desired character tab.
3. Select <OK>.
Entered word is applied.
￭
￭
￭
￭
Name
Description
In PTZ mode, the camera can be panned, tilted, and controlled in 8 directions.
Up/Down/Left/
Right
Rotation
The Web Viewer only supports the PTZ mode.
In Screen mode, the top/bottom/left/right tile can be selected.
￭ When you press the Near/Far button while controlling with the joystick, you can perform control simultaneously.
In PTZ mode, the screen is zoomed in when it is rotated clockwise and zoomed out when it is rotated counterclockwise.
In PTZ mode, presets number 1~8 are run.
Screen mode works as follows.
1~8
1 : Changing live layout / 2 : Search
3 : Export / 4 : Zoom mode
5 : Freeze mode / 6 : Audio
7 : Alarm / 8 : Rec
It allows to exit PTZ mode in PTZ mode.
9
The Web Viewer won't be able to stop the PTZ on its own.
This is used to change to PTZ mode from screen mode.
It allows to exit PTZ mode in PTZ mode.
10
The Web Viewer won't be able to stop the PTZ on its own.
Goes back to the previous screen in the Screen mode.
11,12
120_ appendix
In PTZ mode, Focus Near/Far operation is run.
When using the screen mode, the same operations can be done by moving the mouse.
If you want to enter a special character or uppercase letters, select <Caps Lock> or <Shift>.
Using the virtual keyboard is the same to a normal keyboard use in your region.
Your ID can contain any combination of upper/lowercase alphabet letters and numbers.
If the password length is 8 to 9 digits, you can combine at least three different types of the following characters : upper/lowercase alphabets, numbers, and
special characters.
￭ If the password length is 10 digits or more, you can combine at least two different types of the following characters : upper/lowercase alphabets, numbers,
and special characters.
Troubleshooting
Problem
Problem
Action
Live video will be slow or cut off.
●
●
Check if the network cable is connected properly.
●
Ensure that you have set Network - Connection Mode.
●
Check the IP setting of the PC or camera.
●
Try the Ping Test.
●
Check if there is a different device near the product uses the same IP.
I registered a camera, but the web viewer does not show live
video.
●
After registering a camera, a user need to edit/save the desired layout, before the screen split
mode and live screen fit for the setting appears.
The input camera image is too bright or too dark.
●
Check the registered camera settings in “Setup > Camera > Camera setup”.
The time setup window will pop up.
●
This message is displayed if there occurs a problem with the time setting of the internal clock
or an error in the clock itself.
Contact the retailer or the service center for more information.
The time bar is not displayed in Search mode.
●
The timeline can switch between normal and extension mode.
In extension mode, the time bar may not be displayed in the current timeline. Switch to
normal mode or use the left or right button to navigate through the time bar.
The "NO HDD" icon and an error message are displayed.
●
If you do not format your purchased HDD at all or in a format supported by Recorder, a “NO
HDD” icon (
) will be displayed at the top left. When the “NO HDD” icon is displayed, go
to “Setup > Device > Storage device” and check the HDD connection status and format the
HDD.
●
If the problem persists in a normal condition, contact the nearest service center to have the
HDD checked by the service personnel.
The camera is not connected or the PC fails to connect to the
product.
●
If you keep seeing video slow down or cut off, then check the network environment or camera
condition.
●
Check if the power supply system is properly connected.
●
Check the system for the input voltage from the power source.
●
If the problem persists even after you have taken the above actions, check the power supplier
and replace it with a new one if necessary.
●
Check inside if the cables are properly connected. (SMPS, FRONT)
●
Check if the camera is properly supplied with power.
●
Check the state of the cable connected to the camera and reconnect it after replacing or
disconnecting it.
●
Check the video output connecting the camera's Web Viewer.
●
Check if the network port is properly connected and the network setting is set correctly.
●
Change the hub supporting Gigabit, it may solves.
The screen displays the logo image repeatedly.
●
This may occur from a problem with the main board, or the related software is corrupt.
Contact the nearest service center for more information.
I have installed an additional HDD on the Recorder but it does
not recognize the HDD.
●
See the compatibility list to check if the additional HDD is supported by the Recorder. For the
compatibility list, contact the retailer where you purchased the Recorder.
The Channel button does not work on the Live screen.
●
The Channel button does not work if the current screen is in the event monitoring mode.
●
The cursor will not move to the Start button when I start the
calendar search.
●
Check if the channel and the date that you want to play are marked with the V symbol.
Both channel and date should be checked before you can start playing with the Start button.
I have connected an external storage device (USB Memory, USB
HDD) to the Recorder but the Recorder seems not to recognize
it.
See the compatibility list of external storage devices to check if the connected device is
supported by the Recorder. For the compatibility list, contact the retailer where you purchased
the Recorder.
The screen of the connected monitor is displayed abnormally or
not displayed at all.
●
Check if the necessary cables are connected to the monitor properly.
●
●
Some monitors do not support the Recorder output (HDMI1 or HDMI2/VGA). Check the
monitor resolution.
If I press the ESC key in full screen mode of the Web Viewer, the
system does not switch to a normal split mode.
Press the ALT+TAB keys to select 'ACTIVE MOVIE' and press the ESC key again. The system will
switch to a normal split mode.
It is difficult to configure the network for default search, export,
and router use.
●
For more information, refer to the user manual.
●
If you want to check the basics of the product for a quick start, refer to the Quick Guide
(export, search).
●
If you use the router for network connection, refer to the “Connecting and Setting the
Network” of the Quick Guide.
●
Contact the Recorder administrator for help.
The system does not turn on and the indicator on the front
panel does not work at all.
The video input is okay, but the videos of some channels are
not properly displayed or are abnormally displayed (e.g. black
screen, B/W screen).
–– HDMI1 : 3840x2160(30 Hz), 1080P, 720P, 1280x1024
–– HDMI2/VGA : 1920x1080, 1280x720, 1280x1024, 1024x768
Logo screen on bootup stalls in the <
> state.
No response controlling PTZ in the live viewer.
●
Disconnect the monitor cable from the recorder, and connect again.
●
The HDD may have problems. Visit your nearest customer service center to check the HDD.
●
Check the registered Camera if it support PTZ function.
I forgot the password.
English _121
• appendix
The frame number set for multiple data transmission set in camera or network environment
could differ from the actual rate of transmission.
Click <
> at the bottom of the screen to check the number of incoming frames per
channel and the actual number of frames played.
Basically, when you register a camera, the Live4NVR profile is created and the rate is set to
H.264 800*448 30fps.
If necessary, go to “Setup > Camera > Profile setup > Edit” and change the number of
frames.
Action
appendix
Problem
Exported data cannot be played on a PC or recorder.
Recording does not work.
Action
Problem
●
When setting the file format for exporting, first decide whether the device to be played is a PC
or a recorder before setting.
●
When playing on a PC, the export file format must be SEC.
●
When playing on a recorder, the export file format must be recorder.
In the live screen, the < > icon is displayed and the
message window saying “Record data size exceeded limitation.
Only key frames are recorded. Please check the record settings.”
pops up.
●
If your player does not display a Live image at all, that indicates recording does not work so
first check if you see an image on the screen.
●
Recording does not work if the recording settings are not properly configured.
Scheduled Record : Specify a desired time in "Setup > Record > Record schedule".
Recording will start at the specified time.
Action
●
If the sum of input data for each channel exceeds the limit, the alarm icon and the pop up
window will be displayed. In this case, the channel exceeding the input limit does not record
the entire frame, but it records the main frame only (one or two per sec).
●
Set the permitted data limit to higher than the amount of input data entered in the "Setup >
Record > Record setup" menu.
Recording is not performed in accordance with the settings.
●
If the recording status displays 'Exceeds the maximum hard disc performance', set the
recording size according to the recording performance specifications for each HDD condition.
For details, refer to the "Setup > Setting the Recording” page in the Table of Contents.
The recording screen will slow down.
●
Check whether the recording performance specifications for each HDD condition match the
actual recording settings.
For details, refer to the "Setup > Setting the Recording” page in the Table of Contents.
●
If the data volume of a video exceeds the playing performance, only the main frame is played.
●
Reset the camera recording profile to let the entire recording bps size fit the recording
performance for each HDD condition.
For details, refer to the "Setup > Setting the Recording” page in the Table of Contents.
●
Check the HDD status and determine whether inspection or replacement is necessary.
For details, refer to the "Setup > Setting the Device > Storage device" page in the Table
of Contents.
●
If your camera is using a manual IP, the IP bandwidth might not match with the Network 1 IP
bandwidth of the recorder. Please set it to the identical IP bandwidth.
●
If your camera is in DHCP mode, see if the Network 1 port is functioning in the DHCP server of
the recorder.
–– Continuous : Recording will proceed in any conditions at the specified time.
–– Event : When an event occurs, recording will perform only if the event is of alarm,
motion detection and video loss. If there is no event found, recording will not perform.
–– Continuous/Event : If there is no event found, continuous recording will perform.
Whereas, if an event occurs, event recording will perform.
The image quality of the recording data is not good.
●
Increase the resolution and quality level in "Setup > Camera > Profile setup > Record".
–– Resolution : Select a bigger size when specifying the recording size.
The recording image in the CIF format shows a deteriorated quality as it is enlarged
from a small-sized image.
–– Frame rate : Set the level of frame rate high.
●
If you increase the resolution and the recording quality, the data size increases accordingly.
So the HDD will be filled faster. Overwriting will overwrite the existing data so recording will
proceed at a shorter interval.
Frame rate of the actual recording does not match that of
configured to the camera.
●
If multiple profiles were applied to one camera for video transmission, the actual video stream
can be serviced by the camera at a lower frame rate than specified.
Configure your camera to use one profile for data streaming as possible.
For example, if you set the same profile for recording and network profiles, the actual
recording is made at the specified frame rate.
Still, live video display using split screen mode may apply yet another profile to camera in
accordance with the used screen mode.
Note that allowed limit bitrate for recording / recording settings should be set to be bigger
values than that of camera's feed.
In the recording setting screen, the permitted level for a specific
channel is displayed in orange.
●
If the input data is greater than the permitted level for each channel, it is displayed in orange.
Set the permitted data limit to higher than the amount of input data.
●
If the sum of input data for each channel exceeds the limit, the alarm icon will be displayed. In
this case, the channel exceeding the input limit does not record the entire frame, but it records
the main frame only (one or two per sec).
122_ appendix
If recording loss persists continuously
When registering your camera in PnP mode, if the camera
doesn't get registered but the logo keeps loading attempting
access.
">