IPCEagle 415P-AD Operation And Parts Manual
IPCEagle 415P-AD is a commercial-grade wet pick-up vacuum cleaner designed for heavy-duty cleaning tasks. With its dual vacuum motors, you can operate them together or independently based on your cleaning needs. It features a sump pump with an independent switch that automatically turns on when the water level rises, efficiently pumping it out through a discharge hose. For added safety, a shut-off float seals the vacuum intake when the tank is full, preventing overflow. This versatile machine is ideal for tackling spills, floods, and other wet messes in various commercial settings.
Advertisement
Advertisement
Pump Out Vacuums
Polyethylene & Steel
Operations and Parts Manual
Models:
415P-AD
429P-AD
415DS
When using an electrical appliance, basic precaution must always be followed, including the following:
This machine is for commercial use.
DANGER: Failure to read and observe all DANGER statements could result in severe bodily injury or death. Read and observe all DANGER statements found in your Owner’s Manual and on your machine.
WARNING: Failure to read and observe all WARNING statements could result in injury to you or to other personnel; property damage could occur as well. Read and observe all WARNING statements found in your Owner’s Manual and on your machine.
CAUTION: Failure to read and observe all CAUTION statements could result in damage to the machine or to other property. Read and observe all CAUTION statements found in your Owner’s
Manual and your machine.
DANGER: Failure to read the Owner’s Manual prior to operating or attempting any service or maintenance procedure to your machine could result in injury to you or to other personnel; damage to the machine or to other property could result as well. You must have training in the operation of this machine before using it. If you or your operator(s) cannot read English, have this manual explained fully before attempting to operate this machine.
DANGER: Operating a machine that is not completely or fully assembled could result in injury or property damage. Do not operate this machine until it is completely assembled. Inspect the machine carefully before operation. Use only as described in this manual. Use only the manufacturer’s recommended attachments.
DANGER: Machines can cause an explosion when operated near flammable materials and vapors.
Do not use this machine with or near fuels, grain dust, solvents, thinners, or other flammable materials.
DANGER: Do not
DANGER: Do not ashes.
DANGER: This machine is not
DANGER: Using a machine with a damaged power cord could result in an electrocution. Do not use the machine if the power cord is damaged. Do not use the electrical cord to move the machine. Keep cord away from heated surfaces. Do not unplug by pulling on the cord; grasp the plug, not the cord.
Turn off all controls before unplugging. Do not close a door on cord or pull around sharp edges or corners.
DANGER: Electrocution could occur if maintenance and repairs are performed on a unit that is not properly disconnected from the power source. Disconnect the power supply before attempting any maintenance or service.
2
Warning: Operating a machine without observing all labels, decals, etc., could result in injury or damage. Read all machine labels before attempting to operate the machine. Make sure all of the labels are attached or fastened to the machine. Get replacement labels and decals from the manufacturer’s distributor.
Warning: Electrical components can “short-out” if exposed to water or moisture. Keep the electrical components of the machine dry. Always store the machine in a dry area.
Warning: Use of this machine to move other objects or to climb on could result in injury to the operator or damage to the machine. Do not use this machine as a step or furniture. Do not allow to be used as a toy. Close attention is necessary when used by or near children.
Warning: Moving parts of this machine can cause injury and/or damage. Keep hands, feet, loose clothing, hair, fingers, and all parts of the body away from openings and moving parts.
Warning: Electrocution could occur if you handle the plug or appliance with wet hands. Do not handle plug or appliance with wet hands.
Warning: Do not use without dust bag and or filters in place.
Warning: Rotating fan blades inside the cover. Before opening cover, switch off machine. Wait until the fan/brush stops completely or dust and debris may be ejected.
Warning: If the machine is not working properly, has been dropped, damaged, left outdoors, or dropped into water, return it to an Authorized service center.
Warning: Damage could occur to machine if openings are blocked. Do not put any object into openings. Do not use any opening blocked: keep free of dust, lint, hair, and anything that may reduce air flow.
Warning: Injury could occur to the operator or the machine if used without the dust bag and/or filters in place. Do not use the machine without the dust bag and/or filters in place.
Warning: Injury to the operator and/or damage to the machine could occur when cleaning on stairs, unless caution is used. Use extreme caution when cleaning on stairs.
Warning: To reduce the risk of electrical shock, always use a 3-wire electrical system connected to the electrical ground. Whenever possible connect the machine to an outlet protected by a ground fault interrupter (GFCI). See “Grounding Instructions.”
3
This machine must be connected to the electrical ground to protect the operator from electrical shock. The machine has an approved power cord with three conductors and a plug with three terminals. Connect the plug to a receptacle that has three holes and is connected to the electrical ground. The green (or green and yellow) conductor in the cord is the ground wire. Never connect this wire to any terminal other than the ground terminal.
This machine uses a 120 volt AC 60 cycle electrical circuit. Make sure you have the correct frequency and voltage before connecting the power cord to an outlet.
The machine has a plug as shown in Figure 1. If a receptacle connected to the electrical ground as shown in Figure 1 is not available, have one installed by an electrical
Warning: To reduce the risk of electrical shock, protect the machine from rain. Keep the machine in a dry area.
Warning: To reduce the risk of electrical shock, always use a 3-wire electrical system connected to the electrical ground. Whenever possible connect the machine to an outlet protected by a ground fault interrupter (GFCI).
Warning: Do not cut, remove or break the ground pin. If the outlet does not fit the plug, consult your electrical contractor.
Warning: Have worn, cut or damaged cords and plugs replaced by an authorized service person.
Warning: If it becomes necessary to use an extension cord to reach an electrical outlet, you must use one that is at least one size larger in wire size. Such as a power cord that is marked 12/3 would need to use an extension cord that is marked 10/3. Do not use an extension cord that is undersized.
4
•
•
•
•
•
•
Before use, the equipment must be correctly assembled with all of its components
Check that the electrical outlet is correct for use with the plug on the machine
Before connecting, check that the specified motor voltage corresponds to the main voltage available
Never use the equipment near flammable, explosive or toxic substances: sparks from the motor could cause dangerous reactions.
Always unplug the machine from the electrical outlet when leaving machine unattended or before attempting any repair.
Service and repair should be done by qualified personnel only. Use only original manufacturer’s replacement parts.
•
•
•
•
Machines with dual vacuum motors can be run together or independently as the job requires.
This machine is equipped with a sump pump that has it’s own independent switch.
When the water level rises, the pump will turn itself on and pump the water out through a connected discharge hose.
The machine is also equipped with a shut-off float. As the tank is filled to capacity, a float rises and seals the vac intake, causing a loss of vacuum. Switch off the vacuum when this happens and bring the machine to a drain.
To empty the machine, make sure the power cord for the sump pump is plugged into the A.C. receptacle on the vacuum power head or into a separate wall outlet.
1 . Store the cord on the hook.
2. Store the appliance indoors, away from sources of heat.
3. This appliance is provided with an automatically reset
thermal limiter to avoid damage to motor. If thermal limiter
operates do one or more of the following:
•
Change the bag
•
Clean or replace the cartridge filter
•
Check hose and tank inlet for any obstructions
•
Wait a few minutes for the thermal limiter to re-close the circuit
5
1. Check filter for wear, replace dirt saturated filters that do not respond to normal cleaning.
2. Inspect gasket seals and replace those which have begun to leak.
3. Examine carbon motor brushes and commutator.
S8053200
Note: This machine does not come standard with filters, they can be added as necessary
The filter is accessed by lifting the head assembly off the tank.
The Polyester filter assembly is easily removed by simply lifting the filter basket out of the tank.
The cartridge filters they are removed very easily. First remove the filter retainer by turning the black knob 90 degrees counter-clockwise. The cartridge filter will then slide off of the support assembly.
•
Be sure to frequently clean the filters.
•
Allow filters to thoroughly air dry after washing them before returning them to the machine.
•
Worn filters can affect vacuum performance. Replace the filters when they become worn out and normal cleaning will not restore vacuum performance.
1. Disconnect power cord from power source.
2. To access the vacuum motor, remove the screws that attach the main cover to the head assembly and set the cover to one side.
3. Disconnect the motor’s 2 red lead wires from the main wiring bridge.
4. Disconnect green/yellow wire by removing the screw from the motor core.
5. Remove the four motor mounting screws.
6. Remove motor plate and set aside.
7. Take out the motor and remove the upper and lower gaskets.
8. Inspect gaskets. If they show signs of wear replace the.
9. Install gaskets onto new motor ensuring that they are properly seated.
10. Install the new motor. Make sure foam mufflers are positioned properly.
11. Attach motor plate to motor.
12. Connect green/yellow wire to motor core.
13. Connect motor’s 2 red lead wires to main wiring bridge.
14. Re-assemble vacuum cover.
15. Test for proper operation.
6
(Replacement Carbon Brushes: Part# S8053200)
1. Disconnect power cord from power source.
2. To access the vac motor, remove the screws that attach the main cover to the head
assembly and set the cover to one side.
3. Remove the screws that attach the inner cover to the head assembly and set aside.
4. Remove the carbon brush assembly by removing the 2 screws that attach it to the vac
motor. See Figure 1
5. Slide off the carbon brush connector from the motor terminal. See Figure 2
6. Inspect armature commutator. If it is extremely pitted, grooved or not concentric then
the motor will need to be replaced or sent to a qualified service center.
7. Reverse steps 6 through 4 to install new carbon brush and housing.
8. Repeat steps 4 through 7 for the other carbon brush.
9. Reverse steps 3 and 2 for re-assembly.
10. Test for proper operation.
Figure 1
7
Figure 2
415 Vacuum Motor Assembly
8
No. Part #
1 S81122
2 S80138
3 S80139
4 S81006
5 S82931AUG6
6 S81054
7 S82930G6
8 S81026
9 S81006
10 S81005
11 S83436
12 S81054
13 S82932AUG6
14 S81006
15 S80484
16 S83937
17 S83273
Description
Power Cord 16x3
Strain Relief
Clamp, Cord
Screw, 5x20
Cord Hook
Screw 5x30
Handle
Screw 5x25
Screw 5x20
Screw 5x14
Terminal Block
Screw 5x30
Cover, Single Motor
Screw 5x20
Switch
Filter
Screw 5x35
18 S81502
19 S83383AU
Grommet
Cap
20 S82957AUVEI Cover, Motor
21 S82627 Screw 5x25
22 S82627
23 S82937AUG6
24 S81004
25 S83433
26 S83969
Screw 5x25
Motor Retainer
Screw 4.5x20
Terminal Board
Gasket
27 S81979
29 S83901
30 S81064
31 S81024
32 S81120S
33 S83901
34 S81979
35 S83901
36 S83451AU
Screw 5x25
Gasket
Lock Washer 4x8
Screw 4x8
Motor 1000 watt 120V
Gasket
Screw 5x25
Gasket
Plug
37 S83454
38 S83456
39 S83519
40 S83108G6
41 S81854
42 S86377
43 S86457
44 S83453
Filter, Sound Deadening 3
Filter 3
Cap
Base w/Gasket
Nut, M4
2
1
4
Screw, 4x12
AC Receptacle 110V
Gasket, Receptacle
4
1
1
1
2
1
1
9
1
2
2
1
4
2
1
4
1
Qty.
1
1
1
2
8
2
2
4
1
1
1
1
3
1
1
1
1
1
2
1
9
Float Assembly 415
No. Part #
1 S83706
2 S83724
3 S821243NE
4 S82676-1G
Description
Bushing
Screw 5x25
Body Filter Assembly
Float w/Gasket
Qty.
4
4
1
1
429 Vacuum Motor Assembly
9
No. Part #
1 T82102005
2 S80138
3 S80139
4 S81006
5 S82931AUG6
6 S81054
7 S82930G6
8 S81026
9 S81006
10 S81005
11 S83436
12 S81054
13 S82963AUG6
14 S81006
15 S80484
16 S83937
17 S83273
Description
Power Cord 14x3
Strain Relief
Clamp, Cord
Screw, 5x20
Cord Hook
Screw 5x30
Handle
Screw 5x25
Screw 5x20
Screw 5x14
Terminal Block
Screw 5x30
Cover, Dual Motor
Screw 5x20
Switch
Filter
Screw 5x35
18 S81502
19 S83383AU
Grommet
Cap
20 S82957AUVEI Cover, Motor
21 S82627 Screw 5x25
22 S82627
23 S82937AUG6
24 S81004
25 S83433
26 S83969
Screw 5x25
Motor Retainer
Screw 4.5x20
Terminal Board
Gasket
27 S81979
29 S83901
30 S81064
31 S81024
32 S81120S
33 S83901
34 S81979
35 S83901
36 S83451AU
Screw 5x25
Gasket
Lock Washer 4x8
Screw 4x8
Motor 1000 watt 120V
Gasket
Screw 5x25
Gasket
Plug
37 S83454
38 S83456
39 S83519
40 S83108G6
41 S81854
42 S86377
43 S86457
44 S83453
Filter, Sound Deadening 3
Filter 3
Cap
Base w/Gasket
Nut, M4
1
1
4
Screw, 4x12
AC Receptacle 110V
Gasket, Receptacle
4
1
1
1
2
2
2
9
1
2
2
1
4
2
1
4
1
Qty.
1
1
1
1
4
1
1
8
2
2
2
2
3
1
1
1
2
1
1
1
9
Float Assembly 415
No. Part #
1 S83706
2 S83724
3 S821243NE
4 S82676-1G
Description
Bushing
Screw 5x25
Body Filter Assembly
Float w/Gasket
Qty.
4
4
1
1
Tank and Cart Assembly 415P-AD, 429P-AD
No. Part#
1 S82558-1 V
2 S82623NE
3 S81026
4 S82584G6
5 S82846
6 S82593
Description
Handle
Tank, Poly 24g Black
Screw 5x30
Retainer, Tank
Gasket
Deflector
7 S82652AG6VE Inlet Cover w/button
8 S81300 Rivet
9
10
S87390 Latch
11 S81050 Screw, 5x35
12 S82974
13 S81072-1NE
14 S81860-1NE
15 S81302NE
16 S82559
17 S82680
Washer, Plastic
Support, Handle Front
Support, Handle rear
Rivet 4.8x17
Caster, Swivel
Screw 4x15
8
4
2
2
2
2
8
1
4
2
Qty.
1
1
4
1
1
1
No. Part#
18 S82556
19 S80904
20 S82557
21 S82607
22 S81006
23 S82555
24 S86250
25 S83835NE
Description
Support, Axle
Qty.
2
Wheel 2
Retainer, Wheel 2
Spacer, wheel
Screw
2
8
Axle
Handle Grip
Cap, Wheel
1
2
2
10
Tank Assembly 415DS
No. Part#
1 S82993
2 S81847
3 S81302
4 S83629
5 S83883
6 S81559
7 S81026
8 S82586
9 S82846
10 S82593
11 S82583
12 S82594
13 S82608
Description
Handle
Clamp, Tank
Rivet 5x19
Screw 5x25
Washer
Tank
Screw 5x30
Adapter, Tank
Gasket
Deflector
Inlet Cover
Button
Spring
4
1
1
1
1
1
1
Qty.
2
2
4
4
4
1
11
Cart Assembly 415DS
No. Part#
1 S82993
2 S80917
3 S80913
4 S81301
5 S80902
6 S80914
7 S81402
8 S81403
9 S81301
10 S80901
11 S80915
12 S81028
13 S80904
14 S81401
15 S82052
16 S81301
17 S80479
18 S81012
19 S80478
20 S86250
Description
Handle
Support, Handle
T-Tube
Rivet 5x11
Block
Hand Wheel 8x60
Spring
Plate, Threaded
Rivet 5x11
Base, Cart
Screw 12x140
Masher M12
Wheel
Bushing
Spacer
Rivet 5x11
Caster
Washer
Nut M10
Hand Grip
12
2
2
2
2
2
1
2
1
2
2
2
2
2
2
1
1
1
Qty.
1
2
2
1
6
4
Pump Assembly
7
9
8 10
5
4
3
2
No. Part#
1 DP92372
2 DP99509
3 DP99569
4 DP99182
5 DP99190
6 DP99566
7 DP99565
8 DP99567
9 DP99568
10 DP20310
11 DPGROM11-2-10
Description
Pump
Check Valve
Hose Barb
Hose Clamp
Hose
Barb, Elbow 11/4”
Bulkhead Fitting 1”
Cam Lock, Male 1”
Cam Lock, Female 1”
1” MPT x GHT Fitting
Cord Grommet (Not Pictured)
13
1
1
1
1
2
1
1
1
Qty.
1
1
1
Tools
4
5
8
2
1
3
6
7
Item Part#
S72672
1 S70003
2 S76295
3 S70008
4 S76387
5 S76389
6 S76384
7 S76385
7a S82333
1 S76388
Description
Complete Tool Kit
Crevice Tool
Round Brush
Hose
Wand, Straight
Wand, Curved
16” Floor Brush
16” Floor Squeegee
Replacement Squeegee Blades
Adapter
2
1
1
1
2
1
1
1
1
Qty
1
14
Filters
Part#
S82845
S82852*
S76061*
S82995*
S82855
Description
Filter Bag, Standard Polyester
Cartridge Filter, Paper
Cartridge Filter, Polyester
Cartridge Filter, HEPA Equivalent
Cartridge Filter Retainer
T80093 Paper Filter Bags 3/pkg.
* also requires S82855 Retainer
Where Used
415/429/430 models
415/429/430 models
415/429/430 models
415/429/430 models all models
415/429/430 models
Recommended Spare Parts
S8TOEG845
S80326
Motor Carbon Brush
Main Power Switch
S82845 Polyester Filter, 415/429/430
15
S70042 22” Front-Mounted Squeegee fits all 415/429/430 models
No. Part#
1 S82164
2 S82187
3 S82163
4 S83115
5 S82189
6 S81033
7 S81732
8 S86137
9 S82245
10 S86138
11 S81034
12 S82177
13 S82198
14 S82196
15 S82197
16 S81856
17 S80010
18 S82297
19 S81035
20 S81036
21 S81755
22 S81006
Description
Handwheel 8x45
Small Block, Fixed
Handwheel 6x25
Plate, Adjustment
Driver Pivot
Nut M8
Adjustment Knob
Spring
Squeegee, Rear
Wheel
Washer M8
Body, Wet Fix Tool
Spacer
Squeegee, Front
Bracket, Squeegee
Screw M4x16
Hose
Mounting Bracket
Nut M5
Washer M5
Screw 5x16
Screw 5x20
16
Qty.
1
16
1
1
4
4
1
1
2
1
2
4
4
2
2
1
2
1
1
1
1
2
T80020
30” Front-Mounted Squeegee fits 415/429/430 models with Polyethylene Tanks
No.
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
Not Pictured
Part#
BD735602
BD735601
BD7015509
BD735609
BD715508
BD735609
BD735607
BD735608
BD705201
BD705202
BD705203
BD735610
BD735609
BD735605
BD735603
T80021
Description
Blade, Slotted
Blade, Solid
Support, Blade
Nut, Nylock 1/4-20
Housing Assy.
Nut, Nylock 1/4-20
Wheel, Guide
Bolt, 1/4-20 x 1.75”
Lifting Arm Assy.
Cross Member
Latch Assy.
Bolt, 1/4-20 x 1”
Nut, Nylock 1/4-20
Nut, Nylock 10-24
Screw 10-24
Hose Assy.
1
1
6
6
22
1
2
2
2
2
15
1
Qty.
2
2
2
2
17
Warranty Policy
Limited Warranty
IPC Eagle warrants new cleaning equipment against defects in material and workmanship under normal use and service to the original purchaser as detailed below .
3 years
Subject to the conditions stated below, IPC Eagle warrants all Polyethylene Tanks to be free from defects in materials and workmanship for a 3-year period. Parts replaced or repaired are warranted for the remainder of the original warranty period.
1 year
Subject to the conditions stated below, IPC Eagle warrants all other cleaning equipment components to be free from defects in materials and workmanship for a 1year period. Parts replaced or repaired are warranted for the remainder of the original warranty period.
IPC Eagle will furnish and charge for replacement parts, including transportation, to the original owner through an IPC Eagle authorized service center. If the part is returned within 30 days and is found defective, the owner will be credited for the cost of the replacement part including shipping and handling.
Labor charges are covered for one year from the date of purchase if provided by an authorized IPC Eagle service center.
Wear items exempt from warranty include belts, carbon brushes, power cords, wheels, brushes, pads, handle grips, filters, screens, hoses, and squeegees.
This warranty shall not apply to failures caused by misuse or abuse, improper maintenance as stated in the operation manuals, use of unauthorized repair parts, repairs by other than an IPC Eagle authorized service center, and damage in transit.
IPC Eagle disclaims and denies any liability for any direct, indirect, special incidental or consequential damage which may be suffered as a result of sale, delivery, servicing, use, loss of any product, downtime, labor, freight, or other charges not expressly included herein.
18
19
20

Public link updated
The public link to your chat has been updated.
Advertisement