Siqura MD20 Installation Manual
Siqura MD20, the indoor vandal-proof mini PTZ dome camera, delivers superb performance and durability for indoor security and surveillance installations. Its fast and smooth object-tracking capability makes it ideal for monitoring large areas with precise detail. Connect it to various surveillance systems seamlessly with its built-in Pelco-D protocol and Open Streaming Architecture.
Advertisement
Advertisement
Siqura MD20
Indoor Vandal Proof IP Mini PTZ Dome Camera
Installation
Manual
MD20
Second draft
Contents
CONTENTS
1.
PREFACE .........................................................................................................1
2.
CAUTIONS.......................................................................................................3
3.
OVERVIEW ......................................................................................................5
3.1.
G
ENERAL
O
PERATION
R
EQUIREMENTS
........................................................................5
4.
PACKAGE CONTENTS ........................................................................................7
5.
DOME SETUP AND CABLE CONNECTION...............................................................9
5.1.
P
REPARATIONS FOR
I
NDOOR
D
OME
C
AMERA
S
ETUP
........................................................9
5.1.1.
Switch definition ................................................................................... 10
5.1.2.
Communication switch configuration ........................................................ 11
5.1.3.
Dome ID configuration ........................................................................... 11
5.1.4.
Dome control protocol configuration......................................................... 11
5.2.
E
STABLISHING A
N
ETWORK
C
ONNECTION
.................................................................. 12
5.3.
D
OME
C
ABLE
D
EFINITION AND
R
EQUIREMENTS
........................................................... 14
5.3.1.
Cable requirements ............................................................................... 15
5.3.2.
Verifying Ethernet connectivity ................................................................ 15
5.3.3.
22-pin cable harness.............................................................................. 15
5.3.4.
22-pin connector definition ..................................................................... 16
6.
DOME INSTALLATION...................................................................................... 17
6.1.
I
NSTALLATION
S
CENARIOS
.................................................................................. 17
6.2.
D
OME
D
IMENSIONS
.......................................................................................... 18
6.3.
C
EILING
M
OUNT
.............................................................................................. 18
6.3.1.
Hard ceiling mounting ............................................................................ 19
6.3.2.
In-ceiling mounting ............................................................................... 20
6.3.3.
In-ceiling mounting with ceiling panel....................................................... 23
6.3.4.
Ceiling mounting with straight tube.......................................................... 24
6.4.
W
ALL
M
OUNT
................................................................................................. 25
6.4.1.
Mini wall mount..................................................................................... 25
6.4.2.
Wall mounting with gooseneck tube ......................................................... 27
6.4.3.
Wall box mounting................................................................................. 28
6.5.
C
ORNER
M
OUNT
.............................................................................................. 29
6.5.1.
Corner standard/mini mounting plate ....................................................... 29
6.5.2.
Corner thin/wide box mounting ............................................................... 30
6.6.1.
Pole thin/wide direct mounting ................................................................ 32
6.6.2.
Pole thin/wide box mounting ................................................................... 33
7.
SYSTEM INTEGRATION.................................................................................... 35
7.1.
U
SING A
C
ONTROL
K
EYBOARD
.............................................................................. 35 i
Contents
APPENDIX A: CAMERA ACCESSORIES ......................................................................... 37
M
OUNTING
A
CCESSORIES
............................................................................................ 38
M OUNTS AND M OUNTING B OXES .................................................................................... 40
APPENDIX B: TECHNICAL SPECIFICATIONS ................................................................. 47 ii
Preface
1. PREFACE
Specifications
The information given in this manual was current when published. Optelecom-NKF reserves the right to revise and improve its products. All specifications are subject to change without notice.
Notice
To work with the Siqura MD20 camera, an installer or technician must have the following minimum qualifications:
A basic knowledge of CCTV systems and components.
A basic knowledge of electrical wiring and low-voltage electrical connections.
A basic knowledge of Ethernet and Internet Protocol (IP).
Have read this manual completely.
Copyright
Under copyright laws, the contents of this installation manual may not be copied, photocopied, translated, reproduced or reduced to any electronic medium or machinereadable format, in whole or in part, without prior written permission of Optelecom-NKF.
Important information
Before proceeding, please read and observe all instructions and warnings in this manual.
Retain this manual with the original bill of sale for future reference and, if necessary, warranty service. When unpacking your unit, check for missing or damaged items. If any item is missing, or if damage is evident, DO NOT INSTALL OR OPERATE THIS PRODUCT.
Contact Optelecom-NKF for assistance.
Scope
This manual describes how to connect and install the Siqura MD20 camera.
Operation and configuration of the camera are covered in the User Manual.
1
Preface
Regulations
This device complies with Part 15 of the FCC Rules.
Operation is subject to the following two conditions:
(1) this device may not cause harmful interference, and
(2) this device must accept any interference received, including interference that may cause undesired operation.
This symbol on the product or on its packaging indicates that this product shall not be treated as household waste in accordance with Directive
2002/96/EC. Instead it shall be handed over to the applicable collection point for the recycling of electrical and electronic equipment. By proper waste handling of this product you ensure that it has no negative consequences for the environment and human health, which could otherwise be caused if this product is thrown into the garbage bin. The recycling of materials will help to conserve natural resources.
For more details information about recycling of this product, please contact your local city office, your household waste disposal service or the seller of the product.
Compliance is evidenced by written declaration from our suppliers, assuring that any potential trace contamination levels of restricted substances are below the maximum level set by EU Directive 2002/95/EC, or are exempted due to their application.
2
Cautions
2. CAUTIONS
Handle the camera carefully.
Do not abuse the camera. Avoid striking, shaking, etc. as the camera can be damaged by improper handling or storage.
Install electrical wiring carefully.
Ask a qualified electrician to perform the wiring for the installation. Please note that input electricity to the unit is at a tolerance of 24VAC 50/60 Hz ± 10%.
Ground the camera appropriately to prevent electric shock or damage.
Figure 2.1 Cable harness Figure 2.2 Power input: 3-pin terminal block
Do not disassemble the camera.
To prevent electric shock, do not remove screws or covers. There are no user serviceable parts inside. Please consult technical support if a camera is suspected of malfunctioning.
Do not block the cooling vent on the indoor camera.
This camera has a cooling fan inside. Blocking the cooling holes may lead to overheating and cause malfunction. Overheating is not covered by warranty.
Do not operate the camera beyond the specified temperature and power source ratings.
Use the indoor dome camera under conditions where temperature is between
0°C ~ 40°C (32°F ~ 104°F).
Do not expose the camera to moisture or try to operate it in wet areas.
Turn off the power immediately if the camera gets wet and ask a qualified technician to inspect and service it. Moisture can damage the camera and also create the danger of electric shock.
Do not use strong or abrasive detergents when cleaning the camera.
Use a dry cloth to clean the camera when it is dirty. If the dirt is hard to remove, use a mild detergent and wipe it gently.
3
Overview
3. OVERVIEW
The Siqura MD20 camera is a subcompact dome camera designed to deliver superb performance and durability with an intelligent and stylish housing suitable for indoor security and surveillance installations. The built-in Pelco-D protocol and Open Streaming Architecture provide connectivity to third-party surveillance systems.
Siqura MD20 - Indoor Vandal Proof Mini PTZ Dome
Fast and smooth object-tracking capability.
The most impressive, economical indoor application.
A minimum of one control device is required for operation, such as a control keyboard, a DVR or a PC. The Siqura MD20 camera contains a built-in receiver that decodes commands originating from a control device communicating via Ethernet.
The built-in Pelco-D protocol provides connectivity to other surveillance systems and allows the Siqura MD20 to be integrated with other suppliers' surveillance systems.
Refer to Appendix B: Technical Specifications for more detailed information.
5
Package Contents
Before proceeding, please verify that the box contains the items listed here; the lens is not included. If any item is missing or has defects, DO NOT install or operate the product.
Contact your dealer for assistance.
Siqura MD20 - Indoor Vandal Proof Mini PTZ Dome
Dome Body with 4.2” cover
Hard Ceiling Mount and
Decorative Ring
30-cm Cable Harness for
Power Supply, Video and audio
Fixing Plate
Self-tapping Screws
Plastic Screw Anchors CD: Operation Manuals
7
Dome Setup and Cable Connection
5. DOME SETUP AND CABLE CONNECTION
Before installing or connecting the dome camera, please refer to this section and complete preparation, switch setting and communication switch settings.
5.1. Preparations for Indoor Dome Camera Setup
This installation procedure is for the Siqura MD20 indoor dome camera. Follow the steps below to complete dome housing installation.
To prepare the camera
1.
Unpack the dome package and take out the dome body.
2.
Unscrew the three screws on the dome back and remove the dome housing with the dome cover.
3.
Remove the PE cloth sheet and remove the lens cap.
4.
Replace the dome housing with the cover back. Then screw it and the dome back together. please note When replacing the dome housing, align the cooling fan with the vent on the dome housing, as shown in figure 5.1.
Figure 5.1 Fan aligned with vent
5.
Set the Line Lock switch if required. Other switches only need to be checked if there is a problem.
9
Dome Setup and Cable Connection
It is necessary that the dome ID and communication protocol remain in the default modes when connecting the dome camera to other devices. The switches used for configuring these settings are located on the bottom of the dome camera. These settings are preset to operate the camera with the IP hardware. Changing the settings may make the camera inoperative using the IP connection.
Please refer to figure 5.2 and table 5.1 for switch locations and definitions.
Switch Definition
A Restore server factory defaults.
C
D
Reserved. Must be set to 001.
Reserved. Must be set to 29.
G Reserved.
Figure 5.2 Switches – MD20 (Indoor Dome) Table 5.1 Switch definitions please note Switch A has two buttons. Only the button closest to the 22-pin connector is used to restore factory server defaults. The other button is reserved.
To restore factory defaults
• Power up the camera while holding button A. Continue to hold the button for 30 seconds after powering the camera.
10
Dome Setup and Cable Connection
5.1.2. Communication switch configuration
Table 5.2 shows the function of each pin within the Communication Switch:
Communication Switch Switch Description
SW 1
SW 2
SW 3
SW 4
SW 5
SW 6
Reserved
Line lock switch
Reserved
Table 5.2 Communication switch descriptions
Switches 1, 2, 3, 5, and 6 are reserved.
Switch 4 is used for Line Lock adjustment.
5.1.3. Dome ID configuration
The dome ID configuration is reserved and must be set to 001 as shown in figure 5.3.
First digit Second digit Third digit
Figure 5.3 Dome ID Setup
5.1.4. Dome control protocol configuration
The dome control protocol is reserved and must be set to 29 as shown in figure 5.4.
First digit Second digit
Figure 5.4 Protocol setup
11
Dome Setup and Cable Connection
5.2. Establishing a Network Connection
The factory-set IP address of the Siqura MD20 camera is in the 10.x.x.x range. You will find it printed on a sticker on the bottom of the camera. please note This is the address the module will revert to if you issue a ‘Reset to factory settings; incl. network settings’ command and reboot the module.
To open communication with the camera from a host PC and change the module’s network settings, perform the following steps:
Step 1: Set the PC’s network adapter to the module’s factory default subnet and connect the two devices (see below for details).
Step 2:
Step 3:
Access the module from a web browser or other tool installed on the PC.
Set the module address and subnet mask to the subnet it will be used in and reboot the module.
To address the module from the same PC again, configure the PC’s network adapter once more to assign the PC to the same subnet as the module.
Step 1: Setting the host PC to the factory default subnet of the camera
To configure the network adapter on the host PC
1.
In the Control Panel, open Network Connections (see figure 5.5).
2.
Right-click the connection to be configured, and select Properties .
3.
In the items list, select Internet Protocol (TCP/IP) .
12
Dome Setup and Cable Connection
4.
Click Properties .
Figure 5.5 Opening IP settings on the host PC
5.
In the Internet Protocol (TCP/IP) Properties dialog, click Use the following IP address .
6.
Enter an IP address that will assign your PC to the same subnet as the camera (i.e., within the 10.x.x.x range). Use 255.0.0.0 as a subnet mask.
13
Dome Setup and Cable Connection important To prevent conflicts, be sure to choose a unique IP address. No two devices on a network can have the same IP address.
Figure 5.6 Changing the IP settings on the host PC to the factory-default network settings of the module.
7.
To apply the new settings, click OK , and then click Close .
At this point, connect your PC to the camera. You can connect them directly using a crossover cable, or connect both to a switch.
Step 2: Accessing the module
Using a standard web browser you can now log on to the camera’s internal web server.
Step 3: Changing the module’s network settings
The Network page enables you to make the camera’s network addressing compatible with the network it will be hooked into. Do not forget to save and reboot the camera after changing the settings.
5.3. Dome Cable Definition and Requirements
For operation, the Siqura MD20 camera requires an Ethernet cable to carry the signals to a remote viewing site and a cable to power the dome.
14
Dome Setup and Cable Connection
5.3.1. Cable requirements
For operation, the camera requires video and cable harness as described below:
• A cable to provide 24VAC power supply to the dome.
• A CAT-5 Ethernet cable.
• Optional audio cables.
• Optional coaxial cable to monitor analog video. please note Ensure the power supply corresponds with the dome’s power requirement, or damage will occur. If any mistake happens, contact a qualified technician.
5.3.2. Verifying Ethernet connectivity
Refer to figure 5.7 to determine whether you have established an Ethernet connection:
Ethernet socket LEDs green/ yellow
Green on/off: 100/10 Mbit
Yellow on/blink: link OK, active
Yellow off/flash: link down, TX attempt
Figure 5.7 Ethernet socket LEDs
5.3.3. 22-pin cable harness
A 30cm cable harness, shown in figure 5.8, is shipped with the camera for quick installation for demo or testing usage. This section also provides definitions of each pin within the 22-pin connector on the cable harness.
Power input : 3-pin terminal block
Video output : BNC connector
Audio connector :
In: tip only (pink)
Out: tip and ring (green)
Alarms : Not terminated, see label
Figure 5.8 Cable harness
15
Dome Setup and Cable Connection
5.3.4. 22-pin connector definition
With the 22-pin connector, installers can simply connect the power and video cables to the dome at once. Particularly, the alarm pins are serviceable for connecting alarm input and output devices, such as alarm sensors, sirens or flashing lights with the surveillance system.
For the definition of each pin, please refer to the table below.
A diagram of the 22-pin connector is shown in figure 5.9.
Figure 5.9 22-pin connector
The definitions of each pin are listed in table 5.3:
Pin Definition Cable
20AWG
2 Alarm out NC
20AWG
4 Alarm out NO
20AWG
6 Alarm out common
Shielded
12 Alarm-1
13 Alarm-2
14 Alarm-3
15 Alarm-4
16 Alarm-5
17 Alarm-6
18 Alarm-7
19 Alarm-8
21 VGND
22 Video
24AWG
Table 5.3 22-pin connector definition
16
Dome Installation
Based on the user’s installation environment, the Siqura MD20 dome camera can be installed on ceiling, wall or pole. In the following sections, various indoor dome installation methods and procedures are described in detail.
6.1. Installation Scenarios
Choose your installation scenario from the list below for complete instructions for performing that installation.
Ceiling mounts:
• Hard ceiling mounting, page 19
• In-ceiling mounting, page 20
• In-ceiling mounting with ceiling panel, page 23
• Ceiling mounting with straight tube, page 24
Wall mounts:
• Mini wall mount, page 25
• Wall mounting with gooseneck tube, page 27
• Wall box mounting, page 28
Corner mounts:
• Corner standard/mini mounting plate, page 29
• Corner thin/wide box mounting, page 30
Pole mounts:
• Pole thin/wide direct mounting, page 32
• Pole thin/wide box mounting, page 33
See Appendix A: Camera Accessories for descriptions of the various accessories required for each installation.
17
Dome Installation
The indoor dome dimension is 133 x 173 mm (5.2 x 6.8 In.). Figure 6.1 shows detailed dimensions for dome’s different parts.
Figure 6.1 Siqura MD20 (Indoor dome) dimensions
6.3. Ceiling Mount
Generally, there are four ceiling mounting methods for the Siqura MD20 indoor dome camera:
• Hard ceiling mounting described in section 6.3.1
• In ceiling mounting described in section 6.3.2
• In ceiling mounting with a ceiling panel described in section 6.3.3
• Mounting with straight tube described in section 6.3.4
The following figures show how cables connect to the dome camera in different ways.
Hard ceiling mount In-ceiling mount
(Cables exposed)
Figure 6.2 Mounting options
(Cables recessed)
18
Dome Installation
6.3.1. Hard ceiling mounting
Hard Ceiling Mounting is a standard installation for an indoor dome, and general mounting accessories are equipped in the standard indoor dome camera package. The items and tools needed to mount the dome camera onto the ceilings are listed below. The supplied items are found in the dome camera package.
Items Needed:
• Dome Camera
• Hard Ceiling Mount and Decorative Ring (Supplied)
• Lock Screw Plate (Supplied)
Tools Needed:
• Drill
• Screwdrivers (slotted and Phillips)
To install the mini dome camera in a hard ceiling:
1.
Screw the Lock Screw Plate to the dome body.
2.
Remove the Hard Ceiling Mount from the decorative cover.
3.
Attach the Mount to the ceiling. Mark the locations of all three ceiling holes.
4.
Drill these holes on the hard ceiling.
5.
Fix the Mount with three screws.
19
Dome Installation
6.
Thread the cable harness and Ethernet cable through the center hole of the
Mount and connect the cables to the dome body.
7.
Attach the dome body to the Mount and rotate the dome body clockwise.
Tighten the fixing screw on the fixing plate.
8.
Attach the decorative ring to the mount
Completion
6.3.2. In-ceiling mounting
The following items and tools are required to mount the dome camera to a ceiling. The supplied items are found in the dome camera package.
20
Dome Installation
Items Needed:
• Dome Camera
• T-Bar (Optional Accessory)
• Supplied Screw (Equipped with T-Bar)
• Red Sticker (Equipped with T-Bar )
• Decorative Ring (Supplied)
Tools Needed:
• Tool for cutting a circle on the ceiling
• Screwdrivers (slotted and Phillips)
To install the Siqura MD20 camera with T-Bar Ceiling mount accessory for in-ceiling mounting
1.
Screw the T-Bar Body Holder, which is equipped with the T-Bar, onto the dome back, as shown in the figures.
2.
Place the Red Sticker on the ceiling plate, and cut the circle part out of the ceiling.
3.
Insert the T-Bar into the ceiling hole. please note The T-Bar wings should be inward when inserting the T-Bar into the ceiling hole, as shown in the figure above.
21
Dome Installation
4.
Rotate the T-Bar’s wings to fix the T-
Bar at the edge of the ceiling opening.
5.
Tighten the screws on the wings.
6.
Connect the cable harness and
Ethernet cable to the dome body through the center hole of the bracket.
7.
Mount the dome body onto the bracket and rotate it clockwise. Then ensure the dome body fastened firmly and screw the T-Bar Body Holder.
22
Dome Installation
8.
Attach the decorative ring to the
T-Bar.
Completion
6.3.3. In-ceiling mounting with ceiling panel
To mount the dome camera to a suspended ceiling with the T-Bar, employ the ceiling panel, as shown in figure 6.3.
Figure 6.3 Employing the ceiling panel
To install in a ceiling panel
1.
Cut the ceiling panel in half.
2.
Push the ceiling panel upward into the ceiling opening.
3.
Attach and fasten the T-Bar mount onto the panel as described in section 6.3.2
In-ceiling mounting.
23
Dome Installation
6.3.4. Ceiling mounting with straight tube
The straight tube is available in 25 cm and 30 cm lengths.
Figure 6.4 Ceiling Mount: Straight Tube
Items Needed:
• Dome Camera
• Straight Tube and other equipped items (optional accessory)
• Screws and Screw Anchors for fixing the straight tube onto the ceiling (not supplied)
Tools Needed:
• Drill
• Screwdriver
To mount the dome with the straight tube
1.
Ensure that the ceiling can support the weight of the dome camera and straight tube.
2.
Make a cable entry hole on the ceiling.
3.
Fix the straight tube to the ceiling with proper screws and screw anchors (not supplied).
4.
Thread the cables through the straight tube and the indoor tube adaptor. please note After threading the cables, block the cable entry hole with the supplied sponge(s) to avoid insects entering the tube.
5.
Lock the indoor tube adaptor in position with the supplied screw and washers.
24
Dome Installation
6.
Remove the lock screw plate from the small bag in the indoor tube adaptor and attach it to the dome back plate, as shown in the picture.
7.
Fix the plate onto the dome back with the small screw, as marked in the figure.
8.
Connect the cables to the dome camera.
9.
Mount the dome camera to the indoor tube adaptor.
Afterwards, screw the supplied standard or security screw, as shown in the picture.
6.4. Wall Mount
The locking screw plate should be attached to the camera and used in all wall mount applications.
There are three types of wall mounts for the Siqura MD20 dome camera:
• Mounting with a mini wall mount, as shown in section 6.4.1
• Mounting with a gooseneck tube, as shown in section 6.4.2
• Mounting with a wall box, as shown in section 6.4.3
6.4.1. Mini wall mount
Items Needed:
• Dome Camera
• Mini Wall Mount and other equipped items (optional accessory)
• Screws and Screw Anchors for fixing the Mini Wall Mount to the wall (optional accessory)
• Indoor tube adaptor for MD20 (optional accessory)
25
Dome Installation
Tools Needed:
• Drill
• Screwdriver
To mount the dome with the Mini Wall Mount
1.
Make a cable entry hole in the wall to recess the cables.
For less secure installations, drill a hole in the metal access plate on the bottom of the mount or leave the access plate off entirely. Thread the cables through this hole.
Figure 6.5 Mini wall mount and access plate
2.
Thread the cables through the mini wall mount and fix the wall mount on the wall with proper screws and screw anchors.
3.
Thread the cables through the indoor tube adaptor and lock it to the mini wall mount with the supplied screws and washers.
4.
To prevent insects from entering the wall mount, block the cable entry hole with the supplied sponge.
5.
Connect the cables to the dome camera, and attach the dome to the indoor tube adaptor and fix them with the supplied screw.
26
Dome Installation
6.4.2. Wall mounting with gooseneck tube
The following figures show how cables run through the tube in different ways.
Cables exposed Cables Recessed
Items Needed:
Figure 6.6 Gooseneck cabling options
• Dome Camera
• Gooseneck Tube and other equipped items (optional accessory)
• Screws and screw anchors (not supplied)
• Indoor tube adaptor for MD20
Tools Needed:
• Drill
• Screwdriver
To mount the dome with the gooseneck tube
1.
Make a cable entry hole on the wall to recess the cables. Otherwise, cables can be threaded through the cable entry hole on the tube.
2.
Fix the gooseneck tube to the wall with proper screws and screw anchors (not supplied).
3.
Thread the cables through the gooseneck tube and the with indoor tube adaptor. please note After threading the cables, block the cable entry hole with the supplied sponge(s) to avoid insects entering the tube.
4.
Fix the indoor tube adaptor to the gooseneck tube with the supplied screws and washers.
5.
Connect the cables to the dome camera. Then attach the dome to the indoor tube adaptor and fix them with the supplied screw.
27
Dome Installation
Figure 6.7 Wall Mounting: Gooseneck Tube
6.4.3. Wall box mounting
Items Needed:
• Dome Camera
• Wall Box Mount and other equipped items (optional accessory)
• Indoor tube adaptor for MD20
Tools Needed:
• Drill
• Screwdriver
To mount the dome with the gooseneck tube and wall box
1.
Fix the wall box to the wall with proper screws and screw anchors (not supplied).
2.
Fasten the gooseneck tube to the wall box with the supplied screws and washers.
3.
Thread the cables through the gooseneck tube and the indoor tube adaptor. please note After threading the cables, block the cable entry hole with the supplied sponge(s) to prevent insects from entering the tube.
4.
Fix the indoor tube adaptor to the gooseneck tube with the supplied screws and washers.
5.
Connect the cables to the dome camera. Then attach the dome to the indoor tube adaptor and fix them with the supplied screw.
28
Dome Installation
Figure 6.8 Wall Box Mounting: Wall Box Mount + Gooseneck Tube
6.5. Corner Mount
There are two ways to corner mount a Siqura MD20 dome camera:
• With a standard or mini mounting plate, as shown in section 6.5.1
• With a thin or wide box as shown in section 6.5.2
6.5.1. Corner standard/mini mounting plate
With the corner standard/mini mounting plate and gooseneck tube/mini wall mount, the dome can be mounted on a corner wall.
Items Needed:
• Dome Camera
• Gooseneck Tube/Mini Wall Mount and other equipped items (optional accessory)
• Corner Standard/Mini Mounting Plate (optional accessory)
• Screws and Screw Anchors for fixing the Corner Standard Mounting Plate (not supplied)
• Indoor tube adaptor for MD20
Tools Needed:
• Drill
• Screwdriver
29
Dome Installation
To mount the dome camera with the corner standard/mini mounting plate and gooseneck tube/mini wall mount
1.
Make a cable entry hole on the wall to recess the cables. Otherwise, cables can be threaded through the cable entry hole on the tube.
2.
Fix the Corner standard/mini mounting plate on corner wall with proper screws and screw anchors (not supplied).
3.
Attach the gooseneck tube/mini wall mount to the fixed mounting plate with the supplied screws and washers.
4.
Thread the cables through the gooseneck tube/mini wall mount and the indoor tube adaptor. please note After threading the cables, block the cable entry hole with the supplied sponge(s) to prevent insects from entering the tube.
5.
Fix the indoor tube adaptor to the gooseneck tube/mini wall mount with the supplied screws and washers.
6.
Connect the cables to the dome camera. Then attach the dome to the indoor tube adaptor and fix them with the supplied screw.
Figure 6.9 Corner Wall Mounting: Corner
Standard/Mini Mounting Plate + Gooseneck
Tube/Mini Wall Mount + Indoor tube adaptor
6.5.2. Corner thin/wide box mounting
The corner thin/wide box is designed to be installed with a gooseneck tube.
30
Dome Installation
Items Needed:
• Dome Camera
• Gooseneck Tube and other equipped items (optional accessory)
• Corner Thin/Wide Box (optional accessory)
• Screws and Screw Anchors for fixing the Corner Thin/Wide Box (not supplied)
• Indoor tube adaptor for MD20
Tools Needed:
• Drill
• Screwdriver
To mount the dome with the corner box and gooseneck tube
1.
Make a cable entry hole in the wall to recess the cables. Otherwise, cables can be threaded through the cable entry hole on the tube.
2.
Fix the corner thin/wide box to a corner wall with proper screws and screw anchors
(not supplied).
3.
Attach the gooseneck tube to the fixed corner box with the supplied screws and washers.
4.
Thread the cables through the gooseneck tube and the indoor tube adaptor. please note After threading the cables, block the cable entry hole with the supplied sponge(s) to prevent insects from entering the tube.
5.
Fix the indoor tube adaptor to the gooseneck tube with the supplied screws and washers.
6.
Connect the cables to the dome camera. Then attach the dome to the indoor tube adaptor and fix them with the supplied screw.
Figure 6.10 Corner Box Mounting: Corner Thin/
Wide Box + Gooseneck Tube + Indoor tube adaptor
31
Dome Installation
There are two ways to pole mount the Siqura MD20 dome camera:
• Using a thin wide direct mount as described in section 6.6.1
• Using a thin wide box mount as described in section 6.6.2
6.6.1. Pole thin/wide direct mounting
The dome can be installed to a pole with a thin/wide direct mounting accessory and a gooseneck.
Items Needed:
• Dome Camera
• Gooseneck Tube and other equipped items (optional accessory)
• Pole Thin/Wide Direct Mounting (optional accessory)
• Stainless Steel Straps (optional accessory)
• Indoor tube adaptor for MD20
Tools Needed:
• Stainless Strap Cutter (optional accessory)
• Screwdriver
To mount the dome camera with the pole direct mounting and gooseneck
1.
Fasten the pole thin/wide direct mounting on a pole with equipped stainless straps.
2.
Fix the gooseneck tube to the pole direct mounting with the supplied screws and washers.
3.
Thread the cables through the gooseneck tube and the indoor tube adaptor. please note After threading the cables, block the cable entry hole with the supplied sponge(s) to prevent insects from entering the tube.
4.
Fix the indoor tube adaptor to the gooseneck tube with the supplied screws and washers.
32
Dome Installation
5.
Connect the cables to the dome camera. Then attach the dome to the indoor tube adaptor and fix them with the supplied screw.
Figure 6.11 Pole Direct Mounting: Pole Thin/Wide Direct
Mounting +Gooseneck Tube
6.6.2. Pole thin/wide box mounting
Items Needed:
• Dome Camera
• Gooseneck Tube and other equipped items (optional accessory)
• Pole Thin/Wide Box (optional accessory)
• Stainless Steel Straps (optional accessory)
• Indoor tube adaptor for MD20
Tools Needed:
• Stainless Strap Cutter
• Screwdriver
To mount the dome camera with the pole box and gooseneck tube
1.
Fasten the pole thin/wide box on a pole with equipped stainless straps.
2.
Fix the gooseneck tube on the pole box with the supplied screws and washers.
3.
Thread the cables through the gooseneck tube and the indoor tube adaptor. please note After threading the cables, block the cable entry hole with the supplied sponge(s) to prevent insects from entering the tube.
4.
Fix the indoor tube adaptor to the gooseneck tube with the supplied screws and washers.
33
Dome Installation
5.
Connect the cables to the dome camera. Then attach the dome to the indoor tube adaptor and fix them with the supplied screw.
Figure 6.12 Pole Box Mounting: Pole Thin/Wide Box +
Gooseneck Tube
34
System Integration
The dome camera can be integrated into other suppliers' surveillance systems with the
Pelco D protocols. Refer to the following sections for more information.
7.1. Using a Control Keyboard
The speed dome camera can be controlled through a Pelco keyboard supplied with the
Pelco D protocol.
Function Instruction
Set Preset
Number key + press and hold <Preset > button for three seconds.
Go Preset
Number key + <Preset> to command a dome camera to go to a specific preset position.
9 5 <Preset> Display or hide an OSD menu
Move the cursor in the
OSD menu
Alarm Output On
Alarm Output Off
<ENTER>
Move the cursor up/down/right/left by pushing the joystick up/down/right/left respectively
Set Preset 9 6
Go Preset 9 6
9 5 <Preset> please note Pay careful attention to set up when using a serial server device, such as an
Optelecom-NKF S-44 D data port, to send PTZ commands via a network.
For Pelco D set both the UART gap timeout and the UART max latency to 7.
This ensures efficient and accurate transmission of the commands. Other serial servers will likely use different terms for these settings.
Controlling multiple IP PTZ domes from a single keyboard is beyond the scope of this manual. Please contact technical support for further assistance in this regard.
35
Camera Accessories
APPENDIX A: CAMERA ACCESSORIES
Before installing the camera, compare your accessories to those listed in this section and be sure you have all the parts you need for your installation. important If anything is missing, do not install the dome. Contact your dealer for assistance.
Siqura MD20 accessories
Security Screw Set (equipped with Vandal Proof Cover)
Power Adapter
• Input: 100~115VAC/Output: 24VAC 36VA
• Input: 220~230VAC/Output: 24VAC 36VA please note When wiring, make sure the G/Y wire (Ground) is inserted into the mid-pin of the terminal block
37
Camera Accessories
Mounting Accessories
Before installing, make sure you have all the parts listed. If anything is missing, do not install the dome. Contact your dealer for assistance.
Indoor tube adaptor
For mounting the indoor dome camera onto a gooseneck/straight tube.
White; Diameter: 140 mm (5.5 in.); Height: 74 mm (2.9 in.); 0.3 kg (0.7 lbs)
Attached Components: Hexagon Key, Lock Screw Plate, M5*8 screw×1, M5*8 security screw×1, M3*6 screw×1
Hard Ceiling Mount
For Hard Ceiling use. Height: 19mm; Diameter of three holes: 4.5 mm; Diameter of the bracket: 158 mm; 0.2 kg (0.4 lbs)
38
Camera Accessories
T-Bar Ceiling Mount, T-Bar Body Holder and Red Sticker
For In-ceiling Installation use.
T-Bar Ceiling Mount: Height: 85 mm (3.35 in.); Diameter: 180 mm (7.1 in.); 0.5 kg
(1.1 lbs).Red Sticker: 155 +/- 3 mm (6.1 +/- 1.2 in.)
Ceiling Panel
For ceiling mounting. Zn platted; 610×305 mm (24×12 in.); Diameter: 155 mm (6.1 in.)
39
Camera Accessories
Mounts and Mounting Boxes
To secure the indoor tube adaptor to the tube or wall mount, all tube mounts and the mini wall mount are supplied with the following:
• Cup washer (1)
• 8mm spring washer (1)
• 8mm rubber gasket (1)
• M8*12 screw (1)
Gooseneck Tube
White Color; Iron, 298×385 mm (11.73×15.56 in.) ; 2.1 kg (4.6 lbs)
Mini Wall Mount
White; 184×104×115.2 mm (7.24×4.09×4.54 in.); 0.6 kg (1.2 lbs)
40
Camera Accessories
Swan-neck Mount
White, Iron, Height: 250/500 mm (9.8/19.7 in.) ,Diameter: 50 mm (2 in.)
1 kg (2.2 lbs) / 1.8 kg (4 lbs)
Straight Tube
White, Iron, Height: 250/500 mm (9.8/19.7 in.) ,Diameter: 50 mm (2 in.)
1 kg (2.2 lbs) / 1.8 kg (4 lbs).
41
Camera Accessories
Corner Standard Mounting Plate
White, 222×204×117 mm (8.7×8×4.6 in.); 2 kg (4.4 lbs); Supplied with washer-8×4, spring washer×4, M8*16 screw×4, M8 nut×4.
Corner Thin Box
White/Ivory, 300×164×222 mm (11.8×6.5×8.7 in.); 3 kg (6.7 lbs); Supplied with washer×4, M8*16 screw×4 and spring washer×4.
42
Camera Accessories
Corner Wide Box
White/Ivory; 232×234×210 mm (9.1×9.2×8.3 in.); 2.7 kg (6 lbs); Supplied with washer×4,
M8*16 screw×4 and spring washer×4.
Pole Thin Box
White/Ivory; 291×136×242 mm (11.5×5.4×9.5 in.); 3.1 kg (6.9 lbs); Supplied with M8*16 screw×4, washer×4, spring washer×4, stainless steel straps×4.
43
Camera Accessories
Pole Wide Box
White/Ivory, 270×166×155 mm (10.6×6.5×6.1 in.); 3.2 kg (7.1 lbs); Supplied with M8*16 screw×4, washer×4, spring washer×4, stainless steel straps×4.
Wall Box Mounting
Ivory, 270(L)×166(W)×95(D) (10.6×6.5×3.7 in.); 2.2 kg (4.84 lbs); Supplied with M8*16 screw×4, washer×4, spring washer×4
44
Camera Accessories
Pole Thin Direct Mounting
White/Ivory, 232×136×60 mm (9.1×5.4×2.4 in.); Diameter: 112~140 mm (4.4~5.5 in.);
0.7 kg (1.6 lbs); Supplied with stainless steel straps×4, M8*16 screw×4, washer×4.
Pole Wide Direct Mounting
White/Ivory, 270×170×60 mm (10.6×6.7×2.4 in.); Diameter: 112~130 mm (4.4~5 in.); 1 kg (2.2 lbs); Supplied with stainless steel straps×4, M8*16 screw×4, washer×4.
Stainless Steel Straps
For fixing Pole Direct Mounting/ Pole Box on the pole.
Length: 700 mm (27.5 in.); Width: 0.63”; 0.02 kg (0.04 lbs)
Stainless Strap Cutter
For tension, cut and crimp stainless steel straps. 1.4 kg (3.1 lbs)
Suitable for straps width: 1/2”, 5/8”, 3/4”
All photos of the accessories are subject to change without notice.
45
Technical Specifications
APPENDIX B: TECHNICAL SPECIFICATIONS
CAMERA
CCD Sensor
Optical Zoom
Digital Zoom
Effective Pixels
Horizontal Resolution
Scanning System
Synchronization
Video Output
Minimum Illumination
Focal Length
Focus Mode
White Balance
Iris Control
1/4" EXview CCD
12x
1×~ 10× variable
NTSC 380k
PAL 440k
470 TVL
NTSC / PAL
Internal / Line Lock
1.0 Vp-p / 75 Ω , BNC
1 lux; 0 lux (IR illuminator)
4~48 mm
Auto / Manual
Auto / Manual
Auto / Manual
Electronic Shutter
AGC Control
Back Light Compensation
OPERATION
Built-in Protocol
Auto / Manual
On / Off
Pelco D
Pan Travel
Tilt Travel
720°
-10°~100°
Manual Speed 0.5°~55°/s
Presets 256
Preset Accuracy
Preset Speed
Pan 0.225°
Tilt 0.5°
Pan 5°~300°/s
Tilt 5°~300°/s
Cruise 1
Sequence 8
Auto Pan
Proportional Pan & Tilt
Resume after Power loss
Zone Title
Home Function
Auto Flip
Day/Night: IR Cut Filter
Alarm Input
Alarm Output
4
On/Off (Pan and tilt speed proportional to zoom ratio)
Yes
16
Preset, Sequence, Auto pan, Cruise
Mechanical / Off
On / Off
8
1
47
Technical Specifications
Alarm Reaction
GENERAL
Preset, Sequence, Auto pan, Cruise
Environment Indoor
Operating Temperature 0°C ~ 40°C (32°F ~ 104°F)
Waterproof Standard
Dimension
Weight
Power Source
Power Consumption
-
133 x 173 mm (5.2 x 6.8 in)
1.4 kg (3 lbs)
24VAC 50/60Hz ± 10%
16 w peak (power factor=0.6 24VAC) please note Weight and dimensions are approximate.
All specifications are subject to change without notice.
48
© Optelecom-NKF B.V. 2008
Version 1.0 (081212-1)
Siq MD20 Installman (MW03SP3)
www.siqura.com www.optelecom-nkf.com
*% 199925410900-00 %*
Download
Public link updated
The public link to your chat has been updated.
Document public link
Advertisement
