Taizhou Tianchen Intelligence & Electrics E1800 User Manual

USER MANUAL
Please read this manual carefully before use
Please keep this manual for future reference
ROHS
CONTENTS
1. INTRODUCTION AND SAFETY
2. PRESENTATION
3. INSTALLATION
3
6
4. CONTROL PANEL
5. USE
1
10
11
6. APP USER MANUAL
12
7. MAINTENANCE AND STORAGE
8.TROUBLE SHOOTING
9. EXPLODED VIEW
19
17
16
1. INTRODUCTION AND SAFETY
1.1 Introduction
1. WARNING-this is a dangerous power tool. Use
care when operating and follow all safety
instructions and warnings.
The products are manufactured by Zhejiang Tianchen
Intelligence&Technology Co., Ltd.
www.exgain-tech.com
2. Read the owners/operating manual carefully
and follow all safety instructions before operating
the machine.
Thank you for purchasing our product.
You will have and enjoy the extra free time while using
our robot lawn mower to mow your lawn. You will be
impressed with your lawn's appearance and best of
all, Tianchen robot makes it for you.
3. Objects can be thrown from mower while
operating, keep a safe distance from the machine
when operating, take caution.
1. INTRODUCTION AND SAFETY
4. Keep children, pets and bystanders away from
mower when operating.
The robot mower may be used only by those who know
how to operate it after reading and understanding the
instructions in this manual.
Model: E1800
CE, RoHs approved.
6. Never use a high-pressure washer or even
running water to clean the mower.
Product, product specifications and this document are
subject to change without notice. All other trademarks
are property of their respective owners.
7. Sharp rotating blades. Keep hands and feet
away and do not attempt to lift mower from this
area.
5. WARNING-Operate the disabling device before
working on or lifting the machine.
8. WARNING-Do not ride on the machine.
IMPORTANT!
The following pages contain important safety and
operating instructions. Please read and follow all
instructions in this manual. Carefully read and review
all safety instructions, warnings and cautions contained
in this manual.
2. Specifications symbol
Zhejiang Tianchen Intelligence&Technology Co., Ltd.
Taizhouname:
Tianchen
&Electrics Co,Ltd
Product
RobotIntelligence
lawn mower
Product
name: Robot
Model:
E1800
Ip54lawn mower
Model:
XXXXX
Input:
29.4
V
4A IPX485W
Input: XXX V --- 2A 85W
Made in China
Zhejiang Tianchen Intelligence&Technology Co., Ltd.
Product name: Robot lawn mower
Model: E1800
Ip54
Input: 29.4 V
4A
Ouput : 29.4 V
4A
Made in China
Made in China
S.N.:XXXXXXXXXXX
S.N.:XXXXXXXXXXX
Failure to read and follow these instructions, warnings
and cautions statements may result in severe injury or
death to persons and pets or damage to personal
property. It’s not permitted to modify the original design
of robot. All modifications are made at your own risk.
20XX
Pasted on mower
S.N.: XXXX
year
Pasted on charging station
XX
XX XXX
month date number
: Waste electrical products should not be disposed
of as household waste. Please recycle where
facilities exist. Check with your Local Authority or
retailer for recycling advice.
WARNING
Robot lawn mower can be dangerous
if incorrectly used!
IMPORTANT
ROHS
ROHS
RoHS
INFORMATION
Read through the Operators Manual
carefully and understand the content before
using your Robot.
1.2 Symbols on Mower
These symbols can be found in the mower. Study them
carefully so you understand their significance.
1. The symbol is pasted on the top cover,
Please read the means carefully before use
the appliance.
1 2
4 5 6
7 8 9
0
-1-
1. INTRODUCTION AND SAFETY
- Inspect and clear the mowing area of all debris (toys,
tree branches, items of clothing, anything with a height
less than 6cm) before operating the mower.
4. Charging station symbol.
CAUTION!
- Never raise the mower or attempt to inspect the
blades while the mower is operating.
Position this side of the Charging Station
towards lawn interior.
- Always turn off the power before lifting the mower or
attempting any adjustment.
- When operating the mower in manual mode, maintain
a safe distance from behind or around the mower and
wear proper foot apparel.
This label is pasted on charging station, please make
sure to position this side towards lawn interior. Failure
to do may result in damage to property or persons.
- Do not operate the mower on slopes greater than 30
degrees or use it in manual operation on slopes where
a firm footing is not possible.
5. Warning symbol.
DANGER! Sharp rotating
blade. Keep hands and feet
away. Serious injury can
occur.
DANGER
- Do not operate the mower if any safety feature or
device is damaged or inoperable.
- Do not attempt to disable or defeat any safety feature
or device.
- Use heavy gloves when inspecting or servicing the
blades.
1.3 Symbols in the User Manual
- Wear eye protection and use gloves when installing
the virtual wire and driving the wire stakes/pegs. Firmly
drive all pegs in order to keep the wire from becoming
a tripping hazard.
These symbols can be found in this user manual.
WARNING
- Do not use the charging station power supply with an
extension cord.
xxxxxxxxxxxxxxxxxxxxxxxxx.
- Use only the original equipment power pack and power
supply/charger with this mower.
A warning box indicates a risk of personal injury exist.
- Do not use the power supply/charger if the cord has
become damaged.
IMPORTANT INFORMATION
- Do not place metal objects in the area of the charging
sheets on the charging station.
xxxxxxxxxxxxxxxxxxxxxxxxxxxxxxx.
- Do not place metal objects across the charging heads
of the mower.
An information box indicates a risk of material damage
exist, especially when the stated instructions are not
followed. The box is also used where there is a risk of
user error.
- Do no spray water directly into the docking area of the
charging station or onto the control panel on charging
station.
1.4 Safety instructions
- Keep the lawn mower in perfect operating conditions
by performing the maintenance procedures outlined
by the manufacturer. Good maintenance guarantees
better performance and longer service life.
- The mower has sharp rotating blades! Please care the
mower when it is mowing, in case of serious injury occur.
- Read the owners/operation manual carefully and
follow all the safety and warning instructions.
- This machine has sharp rotation blades! Never allow
the mower to operate unattended; keep bystanders,
children and pets away from mower when in operation.
- Never allow anyone to ride or sit on mower.
- In order not to irreversibly damage electric and
electronic parts, do not wash the robot with water jets
at a high pressure and do not plunge it partially or
thoroughly in water, as it is not watertight.
- Never allow anyone or person who is not familiar with
the safe operation of the mower to operate the mower.
- It is absolutely forbidden to use the robot in explosive
and flammable environments.
- Keep hands and feet away from the cutting blades
and other moving parts.
- The operator or user is responsible for accidents or
hazards occurring to other people or their property.
- Never attempt to service or adjust the mower while it
is in operation.
- Fill up all small holes and even all small mounds inside
working area. It’s to keep the robot with perfect operating.
-2-
2. PRESENTATION
2. PRESENTATION
This chapter contains information you should be aware of before placing the installation.
2.1 What’s in box
1
14
2
15
6
3
5
16
17
4
18
19
20
21
7
13
12
8
9
10
11
22
14
Charger
15
Virtual wire (100m):
Used to mark mowing area and
create a virtual wall for the mower.
3
Power button
4 Cutting height adjustment knob
16
Virtual wire connectors (10pcs):
Used to connect virtual wire.
Charging sheet
6 Blade
7 Home button
Press it when the mower is on,
it goes back to charging station
automatically.
17
Pegs (100pcs):
Used to fix the virtual wire to the
ground around the lawn perimeter
and around obstacles.
18
Blades for replacement (3pcs)
19
Stakes (4pcs):
Used to fix the charging station to
the ground.
1
2
Emergency button
Press it to turn on the mower .
Press it to turn off the mower.
Control panel
5
Charging light
Red: charging
Green: full charged / idle.
9 Virtual wire light
Colorless: in good connecting
Red: Broken wire/ idle
10 Power terminal
8
20
English user manual
21
Charging head
22
Cutting height adjustment spanner
Virtual wire terminal
red terminal
black terminal
12 Hole for stake
11
13
Charging head
-3-
Consumable parts:
1. Blades
2. Virtual wire
3. Virtual wire connectors
4. Pegs
5. Stakes
6. Rear running wheels
7. Front wheels
8.Cutting height adjustment
spanner
2. PRESENTATION
2.2 Function of E1800
- Two cutting modes
There are two cutting modes of the mower, go straight
and go circle (high efficiency).
In Auto, mower selects cutting mode intelligently.
It goes straight if the grass is sparse or it has be cut off,
and it goes circle if the grass is dense or long.
In manual mode, the mower will go where you direct it.
- Lift sensor
There are lift sensors located between the top and middle
cover. If the mower is lifted from ground, it will stops
working within 1 second.
- Tilt sensor
There are tilt sensors installed on the mower too, when
the mower is tilted over 30 degrees in any direction, it
stops working within 2 seconds.
- Virtual wire
The robot lawn mower can't be operated without a virtual
wire. (we suggest to use 100m-600m of virtual wire). The
mower will follow virtual wire to charging station, the virtual
wire acts as a virtual fence. It will get on the virtual wire
until it meets charging sheets, then it gets off from virtual
wire and starts cutting inside.
- Bump sensor
The whole top cover is movable. Both front and side
of mower equipped with bump sensors that will
activate when the mower strikes solid, fixed object when
that object is at least 6cm in vertical height from the
supporting surface of the mower. When the bump sensor
activated, the mower will back up for working.
- Rain sensor
There are two rain sensors located on the mower.
The mower will go back to the charging station
automatically when it's raining.
Rain sensors can be selected ON/OFF from APP.
Turn on: the mower will go back home if it is raining.
Turn off: the mower will go on mowing when it is raining.
- Wifi
The IOS user can search “EGROBOT” in the Apple
Store to download the application.
The Android user search “EGROBOT” in the Google
Play to download the application.
- Mower stops working if virtual wire is cut off or
charging station is power off.
If virtual wire is cut or broken, or the charging station
loose power, the mower will stop working within 3 seconds
- Four steps to safely start the mower
1. Connect charging station with power supply by charger
and make sure the recharging light is in green color.
2. Connect virtual wire to charging station and make sure
it is in good connecting(virtual wire light in colorless).
3. Turn on the power button
4. Press emergency button and start auto mode.
- Overload protect
The cutting motor and running motor are monitored
continuously during operation for any situation that
may cause these motors to over-load.
In the event this is detected, the mower stops operating.
- Touch sensor
Touch the handle when the mower is cutting, it will
cease function.
- Waterproof
Waterproof design, there is an inner cover under top
cover which protect inside parts from humidity.
The waterproof class is I P54.
- Area working time setting(mowing schedule)
Set up one week (From Monday to Sunday, once for
each day) cutting schedule from APP. This function
should be used together with Area location setting.
- Gyroscope
The mower has gyroscope to keep it going straight on
inclines.
- Cutting width: 21cm
- Easy cutting height adjustments
. the mower
The cutting height could be adjusted on
bottom cover cutting height adjustment knob via the
equipped spanner.
- Area location setting(Subarea setting)
You can select Subareas for the mower to cut. This works
well for large lawn. See Section 6.4.
- Auto recharge system
When the mower senses a low battery situation, it will
shut off the cutting motor and search for the virtual wire.
Once found it will follow the virtual wire to the charging
station for recharge automatically. Once charging is
complete, the mower will back up a few centimeters
ready to go again in stand by mode.
- Emergency stop switch
There is an emergency button located on the top of
mower and in red color.
Press it to turn on the mower .
Press it again to turn off the mower.
-4-
- Different languages selection on App.
- Range
There are four range options, user can choose the
distance when robot hit virtual wire according the
condition of different lawns.
2. PRESENTATION
2.3 Technical data
Model No.
E1800S E1800
Mower technical date
Gross weight
Net weight
Mower size
Rated power
Noise
Qty for cutting blades
Cutting height
Cutting width
Cutting speed
Blades rotate speed
Hill capability
Max ambient functioning temp.
Coverage(for once charging)
Working capacity
E1800T
17KGS
Battery
Type of battery
Battery capacity
14KGS
52*39*27cm(LWH)
85W
Charging time
Average working time
Functions:
≤60db
3pcs
Follow virtual wire walking is optional
Cutting height adjustment
Rain sensor
Auto recharge
30degree Max slope
40℃
Intelligent spiraling
Go straight
Anti theft
Lift sensor
Tilt sensor
2
200m ±20％ 500m ±20％
2
2
700m ±20％
2
1000m ±20％ 1500m ±20％ 1800m ±20％
Note:
How large an area is mow per recharged depends
primarily on the condition of the blade and the type of
grass, growth rate and humidity. The shape of garden
is also significant. If the garden mainly consists of open
lawns, mower can mow more area per hour than if the
garden consists of several small lawns separated by
trees, flower beds and passages.
WIFI Application
Bump sensor
Waterproof
Touch sensor
Time set-up system
Emergency switch
Charging station and virtual wire
Charging station size
44*48.2*15cm(LWH)
600m/0.5mm
Virtual wire maximum length
Standard virtual wire length
100m/0.5mm
Password set-up
Gyroscope
Language option
Subarea setting
Range option
2.4 Working route
-5-
6.6Ah
≤1.5hours ≤2hours ≤3hours
45mins 2-3hours 3-4hours
Mower is disabled if virtual wire is cut or broken
21cm
35m/min
3000rpm
2
Lithium
4.4Ah
Mower is disabled without power to charging station
2.5-5.5cm
18cm
2
2.2Ah
3. INSTALLATION
3. INSTALLATION
3.3 Charging station installation
This chapter describes how you to install this mower.
Before starting the installation, read the previous
chapter 2. Presentation.
- Choose best installation place, please make sure
it is flat, no water, no magnetic interference and no
obstacle in the front of charging station.
Read the whole of this chapter before starting the
installation. How the installation is made also affects
how well the mower will work. It is therefore important
to plan the installation carefully.
3.1 Preparations
Training
- Read the instructions carefully. Be familiar with the
controls and the proper use of the mower.
- Never allow people unfamiliar with these instructions
or children to use the mower. Local regulations
may restrict the age of the operator.
- The operator or user is responsible for accidents or
hazards occurring to other people or their property.
Charging station best install place:
1. Make sure it is flat
2. No magnetic interference
3. No water and far away from puddle
4. No obstacle in front of charging station
3.2 Hardware adjustments
Blade adjustment
The mowing system used by this mower is based on
an effective and energy efficient principle. Unlike
normal lawn mowers, the mower cuts the grass instead
of striking it off.
Rain sensors on the mower is optional,suggest operate the
mower in dry weather to obtain best possible result.
Even though the mower can mow in rain,wet grass
collects on mower easily and the risk of slipping
on steep slopes increases.
- Please fix the charging station on horizontal place and
correct direction.
- Lay virtual wire
as picture shows.
Peg
- Fix the charging
station with four
stakes by
hammer.
The blades must be in good condition to obtain the best
mowing result. In order to keep the blade sharp for as
long as possible it is important to keep the lawn free
from branches, small stones and other objects
(especially the objects less than 6cm height). Please fill
up small holes and even out small mounds to make sure
lawn is flat.
IMPORTANT INFORMATION
How to adjust the cutting height:
1. Turn power off
2. Use height adjustment spanner rotate knob clockwise.
3. Adjust cutting height device manually 2.5cm-5.5cm.
4. Use tool rotate knob anticlockwise.
Before locate the charging station, please make sure
mower must follow the virtual wire and back to
station in CLOCKWISE direction.
IMPORTANT INFORMATION
Do not tread or walk on the charging station plate.
Cutting height adjustment knob
Cutting height explanation: take 3cm level for example.
Cutting height: 3cm
Grass
Height
3CM
3cm
-6-
3. INSTALLATION
3.4 Virtual wire installation
The virtual wire can be installed in one of the following
ways:
- Securing the wire to the ground with pegs.
It is preferable to staple down the virtual wire, if you
want to make adjustments to the virtual wire during
the first few weeks of operation.
- Bury the wire
It is preferable to bury the virtual wire(max depth: 5cm)
if you want to detach or aerate the lawn.
- Bury virtual wire below grass and fasten it on
the ground with pegs, so that the mower should
not cut the wire.
virtual wire
Add pegs in order to pull the
virtual wire down to the ground
surface, below the grass tips.
IMPORTANT INFORMATION
Hard or dry ground may cause pegs to break when
driving them in. In extreme cases, watering the lawn
where the pegs will be driven.
If necessary both methods can be combined so one
part of the virtual wire is stapled down and the
remainder is buried.
- Install virtual wire with pegs 1 meter apart. It’s
best to use smooth radius corners than sharp
angles. See pictures.
- A minimum distances between the front of the charging
station and an obstacle is 2 meters. And make sure the
distance from corner to front of charging station is at least
2.5 meters. Make sure to lay a 2.5 meters minimum
straight-light of virtual wire in front of charging station.
OK
- If a high obstacle, for example a house, wall, fence or
other obstacle which is higher than the cutting lawn
borders the working area, the virtual wire should be laid
at least 40cm from the obstacle. This will prevent mower
from colliding with the obstacle.
- If a passage or a ground with same height of cutting lawn,
the virtual wire should be laid at least 10cm from the edge.
- A minimum distance between the pool edge of virtual
wire is 40cm.
- A minimum distance between two corners is 1meter.
>90
Min:40cm
10cm
Max:1cm
Pool
Passage or
a ground with
same level
of the lawn.
- A maximum distance of the virtual wire
to and from the island is 1cm, and fix the
two wires with one peg.
- There are two types of set up of the
virtual wire around the charging station.
Put the charging station near corner.
please take location for reference.
Min:40CM
House, wall, fence or
other obstacle higher
than the lawn
Please make sure to set a straight-line
at least of 2.5m in front of charging
station. The charging station should be
far away from puddle.
Straight-line
at least:2.5m
Min:40CM
Location
-7-
3. INSTALLATION
- Use the virtual wire to isolate areas inside the working
area by creating islands around obstacles that can
not withstand a collision, for example, flower beds and
fountains. Run the wire out to the area, route it
around the area to be isolated and then back along
the same route. If pegs are used, the wire should be
laid under the same peg on the return route. When
the virtual wire to and from the island with a maximum
distance of 1cm, the mower can drive over the wire.
- If protected obstacles are grouped closely together
isolate them individually. Continuous virtual island
if obstacles are close to edge, leave them out of the
mowing area.
Max: 1cm
- Care must be taken not to create a corner sharper
shorter than 90 degrees when setting up virtual wire.
A corner sharper less than 90 degrees can cause the
mower to lose track of virtual wire. We can make
greater than 90 degrees corner like follow picture
shows.
Incorrect corner
setup
Correct corner set up,
using several angle to
avoid an angle of less
than 90°.
Greater than
2m
Max: 1cm
Min: 2m
Max: 1cm
Proper setup in sharp corners
40cm
Virtual wire
Virtual wire
- The distance between charging station and virtual
loop should be 2 meters at least.
Virtual wire connecting
- Joining the virtual wire .
If the virtual wire is not long enough
and needs to be spliced: Use supplied
wire connector. It is waterproof and
gives a reliable electrical connection.
To splice: Insert both cable ends in the
connector. Now press down the button on
top of the connector fully. Use a pair of
pliers or the like, as the button on the
connector is difficult to press down by
hand.
1cm
Greater
than 2m
Tree with hole or flowers
around require placing a
wire around it
- 8-
3. INSTALLATION
3.7 Power connection.
3.5 Charging head installation.
1. Connect charger terminal b with charging station power
terminal a.
Connect 1 from plug a to 1 from plug b and screw it
it tightly.
-
+
2
1
Power terminal
on charging station
+
1
2
Power terminal
on charger
2. Connect the charger with power supply.
Please fasten the charging heads on the charging
station in clockwise.
3.Charging light on station in green: Non-recharging.
charging light on station in red: recharging.
3.8 Recharge.
1. When the mower senses a low battery situation, it will
shut off the cutting motor and search for the virtual wire.
Once found it will follow the virtual wire to the charging
station for recharge automatically. Once charging is
complete, the mower will back up a few centimeters
and stand by.
3.6 Virtual wire and charging station connecting.
1. Cut the two ends of virtual
wire to a length of 1cm that’s
convenient for reaching
the virtual wire terminal on
charging station.
Strip the two ends of wire.
2. The mower will go back to the charging station
automatically when it's raining.
Rain sensors can be selected ON/OFF from APP.
Turn on: the mower will go back home if it is raining.
Turn off: the mower will go on mowing when it is raining.
2. Connect the cut two ends of virtual wire to virtual wire
terminal located on charging station.
Pls take care of positive and negative terminal.
IMPORTANT INFORMATION
All the buttons (except the emergency switch and
power button ) are locked which can not be used
during the robot is in recharging.
3. The mower reverses several centimeters and stop
there with entering standby mode after fully
recharged.
3.The virtual wire light turns colorless while virtual wire
connected well with charging station.
A failed connecting between virtual wire and charging
station cause a blinking red light and send out a
beeping from charging station.
WARNING
Redundant virtual wire at back of charging station
must be cut off.
-9-
4. CONTROL PANEL
4. CONTROL PANEL
4.1Control Panel view
4.5Match mower with charging station:
Take mower close to charging station, turn on the emergency
switch,press auto button A and home button
simultaneously, the signal light
starts flickering, press the
home button on the charging station, the signal light - turns
bright,press confirm button on the mower panel until the
signal light is off, the matching complete, turn off the
mower and started again.
Note: Mower was matched with charging station before leave
the factory.
A
A
Auto mode
Confirm button(to confirm your selection)
Home button
Power light(lighted when power is on)
Signal light
(lighted when mower detect signal from charging station)
Alarm light(flickering when mower alarms)
4.2AUTO MODE
Turn on the emergency switch, when the signal light flickers
to bright, press auto button A , indicator light start flickering,
press confirm button , indicator light off, mower enter into
the auto mode.
4.3HOME MODE
Turn on the emergency switch, when the signal light flickers
to bright, press home button , indicator light - starts
flickering, press confirm button , indicator light off, mower
enter into home mode.
Note: If the signal light keeps flickering all the time, need to
rematch the address between mower and charging station.
4.4Mower alarming
When the mower stops with alarm, the alarm indicator light
will keeps flickering, cancel alarm by press confirm button ,
alarm indicator light will be off.
Note: If the mower stopped frequently, please check alarm
messages which showed on the APP.
- 10 -
5. Use
5. USE
5.2 Starting the mower
IMPORTANT INFORMATION
- Do not leave the mower to operate unattended if you
know that there are pets, children or people in the
vicinity
There are two locations of start the mower.
1.Take the mower clockwise onto virtual wire, make sure
that the mower is not connected with two charging
sheets on charging station. Otherwise, the mower is in
recharging Mode, it can not be started.
- Mow only in daylight or in good artificial light.
2.Take the robot to start point.
- Avoid operating the mower in wet grass.
- Do not operate the mower when barefoot or wearing
open sandals.
If set Edge mowing off, the robot begins cutting inside
lawn directly.
If set Edge mowing on, the robot will follow the virtual wire
cutting for one circle, and back to station first.
- Always wear substantial footwear and long trousers.
- Always be sure of your footing on slopes.
- Use extreme caution when reversing the mower
towards you.
- Always switch on the mower according to instructions
with feet well away from the blade.
To start the robot.
1. Turn on the Power button under the mower.
2.Press the Emergency button to turn on the robot.
3. Select AUTO A
WARNING
mode, the mower starts working.
Note:If the mower lost contact with station, AUTO or
Read the safety instructions before you start
your mower.
HOME mode is not able to start.The signal light
is always flickering,then need rematch the mower with
charging station,pls refer to 4.5Match mower with charging
station.
WARNING
Keep your hands and feet away from the
rotating blade. Never put your hands or feet
close to or under the body when the motors
are running.
5.3 Stopping mower /Turning off mower
1. Press stop button from APP. Mower
stops and enters standby mode.
2. The mower can be turned off by pressing the
Emergency button directly.
3. Press power button under the mower to turn off.
5.1 Preparation
- Ensure the correct installation of the virtual wire.
5.4 Emergency Switch
- Periodically inspect the area where the mower
is to be used and remove all stones, sticks, wires,
bones, and other foreign objects especially the height
of objects is less than 6cm.
Press Emergency button at any time the mower power
off at once. User has to restart it.
- Periodically visually inspect that the blades, blade
bolts and cutter assembly are not worn or damaged.
Replace worn or damaged blades and bolts in sets to
preserve balance.
- Connect the two ends of virtual wire to the terminal
on charging station, and ensure virtual wire is in good
connecting. (Light on charging station is in colorless).
- Insert charger into charging station and secure it with
threaded cap. And then connect charger to power
supply. Ensure the charging station has a good connection
and the light on charging station is Green.
- Periodically inspect the lawn is without any small
hole or mound.
IMPORTANT INFORMATION
User can not start the mower if virtual wire or
charging station is not in good connection.
- 11 -
6.APP USER MANUAL
The APP is available for IOS and Andriod phone.
Download and Install：
The Android user pls search “EGROBOT” in Google Play to download.
.
The IOS user pls search
“EGROBOT” in the Apple Store to download.
For the first time please connect the charging station and virtual wire
and turn on the mower according to the user manual.Then enter the smart
phone setting interface--WI-FI to connect the device.Pls note for first time it takes
about 3-5minutes to connect device, and the device can only connect with one phone
at the same time.
The using of the App:
Click the APP you installed and enter it.
- 12 -
6.APP USER MANUAL
6.1 Remote control function
3.For the functions like rain sensor,touch sensor,audio alarm
are optional.
Rain sensor:
ON: mower goes back to charging station when it
is raining.
OFF: mower goes on working when it is raining.
After finish setting function,pls press Send to save the
settings.
1.Press ”Auto”, the mower will
6.3 Date&Week&Time settings
work automatically.
2.Press “Remote”, the mower
will work in manual and user
could direct the mower to work
with indication.
Pls note in Remote mode, robot does not recognize the
wire and station.
3. Press “Home”, the robot will go back to station
1.You can synchronize the
automatically.
mower time to cellphone time.
4.Press “Stop” can stop the robot and stand by.
2.After setting new time, pls
Pls note this does not work when mower is charging.
.
5.The blades could be turned on or off by press “MOW” .
press Send to save the
settings.
6.2 Function settings
6.4 Working Area Setting
1. There are 13 languages
for option: English/French/
1.This function is to increase
German/Danish/Swedish/
the mowing efficiency for
Finnish/Norwegian/Italian/
large area.It allows to
Spanish/Russian/Polish/
separate a large area into
Dutch/Chinese.
maximum 6 small areas.
2.Range function:there are four range options, user can
2.Area location setting
2.1 before entering into this interface, pls separate the
garden into several areas as per your own demand.
choose the distance when mower hit virtual wire according
the condition of different lawns.
1
2
Take separate 3areas for example below:
3
4
- 13 -
6.APP USER MANUAL
3.Area working-time setting
3.1.The Area working-time setting should be used
together with Area
location setting.
3.2.Choose the mower
working day per week.
3.3Set the start time,
then set the working
time for each area
and Send.
-Pls note if the working
areas are for example
3areas,do not set the
time for other
unselected areas.
-If set Area 1 with 0min,
it means Non-cutting in
Area 1.
-If unselect working in
Area 2,even has set
working time in Area 3,
mower will not work in
-Route the wire around the passage to separate the
Area 3.
3.4.Edge mowing:
the area.The virtual wire to and from the edge of
passage is 1meter at least.pls refer to below picture.
ON:every time mower
-A minimum distance between the virtual wire which
will cross to the back
is to make passage is 50cm.
2.2 choose the areas that you set accordingly:
of station to mow the
2-1Area 1 is non-optional,selects by default.
2-2After select Area, the symbol
* will be in red color.
wire and follow the wire
edge grass on virtual
back to station first.
2-3 Start locating to set memory
point.
A memory point is to program the
where to leave virtual wire and
4.Put the mower back to station and wait for working.
go inner lawn.Each area needs
a memory point.
Pls make sure the mower voltage
more than 27V before setting the
memory points,and pls put the
mower at charging station before
locating.
-It is best to set the memory point
in the middle of two corners.
--A better position of memory point is 3meter distance
from the beginning or the end of an area.
- 14 -
6.APP USER MANUAL
6.5 Password
1.This is for setting the
mower password.
2. and you can set 4-digit
password.
Initial password:1234.
Input old password,then
Input new password and
Send.
3.Password function is optional.
6.6 Mower-state Query
1.You can get the mower
voltage info.
2.Click “Mower-state Query”
to view alarm info.
- 15 -
6. MAINTENANCE AND STORAGE
15. Servicing of the mower should be according
to manufacturers instructions. This product
(include battery pack)must be disposed of at a
designated collection pint for electrical and
electronic waste. For more information, contact
your local city office or the shop where you
purchased the product.
6.2 Robot Storage
Packed the mower and all spareparts with the original
package, and storage the carton off the ground in a
cool, dry place. Temperature should not be colder
than 14F°(-10℃)
6.3 Blade replacement
Blade replace steps:
1.Stop the robot in safe conditions.
2. Wear protective gloves.
3. Turn the Robot upside down.
4. Unscrew the blade and remove it.
5. Replace a new blade and screw it tightly.
6. MAINTENANCE AND STORAGE
- During maintenance operations, use the individual
protections indicated by the Manufacturer , especially
when intervening on the blade.
- Before performing maintenance operations, make
sure that the robot has stopped in safety conditions.
PROGRAMMED MAINTENANCE INTERVALS CHART
Frequency
Component
Blade
Every week
Type of operation
Reference
Clean and check the
efficiency of the
blade
See “Robot
cleaning”
If the blade is bent due
to an impact or if it is
worn-out, replace it.
See “Blade
replacement”
Every month
Robot
Carry out cleaning
See “Robot
cleaning”
Every 3 months
Robot
Carry out for rechage
See “Battery”
6.1 Robot cleaning
1.Stop the robot in safety conditions.
2. Wear protective gloves.
3.Clean all the outside surfaces of the
robot with a sponge soaked in warm water.
4.Do not use solvents or benzene so not to damage
the varnished surfaces and the plastic components.
5.Do not wash the inside parts
of the robot and do not use water
jets in pressure so not to damage
the electric and the electronic
components.
WARNING
Never use a high-pressure washer or
even running water to clean the robot.
6.Check the lower part of the robot (cutting blade area
and wheels) and remove the deposits and/or residues
that might obstruct the correct functioning of the robot.
7. To remove the deposits and/or other residues from
the blade, use a suitable brush.
8. Clean the outside of the charging station from any
accumulated residues.
9. Keep all nuts, bolts and screws tight to be sure the
appliance is in safe working condition.
10. Replace worn or damaged parts for safety.
11. Ensure that only replacement cutting means of the
right type are used.
12. Ensure that batteries are charged by using the correct
charger recommended by the manufacturer.
13.Incorrect use may result in electric shock,
overheating or leakage of corrosive liquid from the
battery.
6.4 Front wheel cleaning
When front wheels are not easy to rotate, please turn robot
upside down, check it and dismantle the screw cap to take
the front wheel out of robot, dismantle end caps and
remove the residues, like mud, grass etc from end cap,
then reinstall it on the robot.
6.5 Battery
The battery is maintenance-free, but has a limited life
span of 1-3years. Battery life is dependent on the
length of the using season and how many hours per
week the robot is used. A long season or many hours
of use per week, means that the battery must be
replaced more regularly.
- Attentions of lithium batteries
Please charge the lithium batteries in accordance with
standard time and procedures.
When the power is too low. It should be started
charging as soon as possible.
Storage, we suggest the optimum storage of lithium
battery is with 80% power and keep in the shade.
Don’t connect the anode and cathode of battery.
Don’t take apart, repair or modify the battery privately.
- Disused battery processing
Please contact the nearest waste treatment center
and consultation with recycling and proper disposal
of views.
IMPORTANT INFORMATION
14. In the event leakage of electrolyte flush with
water/neutralising agent, seek medical help if it comes
into contact with the eyes etc.
- 16 -
Charge the battery fully at the end of the season
before winter storage. And recharge it every 3
months.
7.TROUBLE SHOOTING
7. TROUBLE SHOOTING
Problem
Auto mode is not able to
start,charging station is
beeping.
Signal light is off.
Alert info
Possible reasons
1.The virtual wire fails to
send signals.
Virtual wire was cut off.
2.The virtual wire was
cut off.
Solutions
1.Check the virtual wire
light on charging station.
Be sure the virtual wire is
connected to the charging
station well (light in
colorless).
2. Connect the virtual wire
with wire connectors.
Auto mode is not able to
start,charging station is
beeping.
Signal light is off.
Mower stops working
and beeps.
Charging station is out of
power.
Lift sensor or pressure sensor
activated.
Current of right running motor
is too large,check it.
Mower stops working
and beeps.
Mower stops working
and beeps.
1.main power is shut off.
Bad communication
between charging station
and mower.
1. Check the power and
make sure the charger is
connecting well with power
supply and charging
station.
1. Mower is lifted from
ground.
1. Take the mower to level
ground and restart it.
2. Someone or object ride 2. Take the object away
or sit on the mower.
from mower and restart it.
1. Running wheel strike
hard objects.
1. Clean the lawn and make
sure it is free from hard objects.
2. The mower is trapped
in lawn.
2. Clean the lawn where mower
is trapped or restart the mower
in another place.
1. Cutting height is too low.
1. Adjust the cutting height
to suitable height.
Current of left running motor
is too large,check it.
Current of cutting motor is too 2. Blade strikes hard
large,check it.
objects.
2. Clean the lawn and make
sure it is free from hard objects.
3. Clean the lawn where mower
3. Mower is trapped in lawn is trapped or restart the mower
in another place.
- 17 -
7.TROUBLE SHOOTING
Problem
Mower stops working
and beeps.
The batteries can not
recharge
Display
Robot is over tilted.
Possible reasons
Solutions
Mower is tilted over than
30 degrees from the
ground.
Turn off the mower and take
the mower to level ground.
Then restart the mower.
1.Charger is not powered
on.
1. Check whether charger
is well connected.
2.Battery lifetime
decreases.
2. Send the mower to service
station and replace the
battery.
1. Grass is extremely
overgrown or very wet,
1. Cut the grass appropriate
height.
2. Terrain needs
landscaping repairs.
2. Fill in all holes, cover or
exclude all exposed roots
in order to smooth the
terrain.
Mower does not complete
the edge.
Obstacle along the path.
Watch the full operation of
follow virtual wire walking
and confirm no obstacle
is present.
Mower does not detect
the charging station
contacts.
The ground before the
charging station isn’t flat.
Reset the charging station
in a flat place.
Mower reaches charging
station when its contacts
are above the charging
sheets.
Height difference between
the charging station and
lawn surface at the
entrance to charging station.
Confirm the ground before
the charging station is leveled
with the station if necessary
fill area with dirt and level off.
The mower behaves in an
anomalous around flower
beds.
Virtual wire incorrectly
placed
Relocate the virtual wire.
Mower gets stuck,
does not move.
1. Damaged cutting blade. 1. Replace a new blade.
The mower is very noisy.
2. Cutting blade flooded by 2. Stop the mower in safety,
residues(tapes, ropes, plastic use protection gloves to
fragments, etc)
avoid the risk of cuts on
hands, remove the fold
3.The start of mower occurred cause from blade.
with obstacles being too
closed (less than 1m away) 3. Start the robot in new place.
or in presence of unexpected
obstacles (fallen branches, 4. Get the motor repair or
replace by service station.
forgotten objects, etc.)
4. Damaged running motor
or cutting motor.
5. Grass too high.
- 18 -
5. Increase the cutting height
or use a normal lawn mower.
8. EXPLODED VIEW
Robot Exploded View
- 19 -
8. EXPLODED VIEW
Robot spareparts list:
No.
1
2
3
4
5
6
Sparepart Name
Cutting height adjusting
motor
Cutting motor fixed mount
Shaft sleeve
Cutting motor fixed seat
Cutting motor base
Rubber ring gasket
Rubber ring
Protective shield
Running motor
Oil seal
Running motor end cap
Rear wheel
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
Wheel shell
Seal strip
Bottom base
Brushless motor PCB
Battery cover
Battery
M5 screw
Flat washer-1
Front wheel
Recharging sheet
No.
24
25
26
27
28
29
30
31
32
33
34
35
36
37
38
39
40
41
42
Spareparts Name
Adjusting motor PCB
Display PCB
Rain sensor
Middle cover
Emergency base
Emergency seal ring
Emergency switch
Bump rubber
Top cover
Globe joint-front
Globe joint-rear
Ball head
Pressure ring for rubber
Rocking bar rubber
Rocking bar axle
Support ring
Flat washer-2
Reposition spring
No.
47
48
49
50
Spareparts Name
Flat washer-3
Blade shield
Blade M4 screw nut
Blade
51
Blade M4 screw
52
Cutting motor
53
Blade head
54
55
56
57
M8 screw nut
Touch sensor PCB
Main PCB
Power button
Centering block
43
Magnet-1
44
45
46
Hall PCB
Snap ring
Magnet-2
Virtual wire sensor PCB
Charging Station Exploded View
1.Station cover
2.PCB
3.Power terminal
4.Virtual wire terminal
5.Short plate
6.Charging head
7.Charging head permanent seat
- 20 -
Robot lawn mower
USER MANUAL
">