Axis 5570e User Manual

AXIS 5570e/AXIS 5670e
Host-to-LAN Print Servers
User’s Manual
AXIS 5570e / AXIS 5670e User’s Manual
1
Regulatory Information
Safety Notices
Important:
Take some time to read through the safety notices before installing the print server. Please observe all safety markings and
instructions when using this product.
Observe “Important:” in the text to avoid operational impairment. Do not proceed until you have fully understood the
implications.
Electromagnetic Compatibility
(EMC)
USA
This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC
Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This
equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the
instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not
occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be
determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the
following measures:
- reorient or relocate the receiving antenna
- increase the separation between the equipment and receiver
- connect the equipment into an outlet on a circuit different from that to which the receiver is connected
- consult the dealer or an experienced radio/TV technician for help. Shielded (STP) network cables must be used with this unit to
ensure compliance with the class B limits..
Europe
This digital equipment fulfils the requirements for radiated emission according to limit B of EN55022, and the requirements
for immunity according to EN55024 residential, commercial, and light industry. Compliance is not valid for unshielded
network cables.
Japan
This is a class B product based on the standard of the Voluntary Control Council for Interference from Information
Technology Equipment (VCCI). If this is used near a radio or television receiver in a domestic environment, it may cause radio
interference. Install and use the equipment according to the instruction manual. Compliance is not valid for unshielded
network cables.
Australia
This electronic device meets the requirements of the Radio communications (Electromagnetic Compatibility) Standard 1998
AS/NZS 3548. Compliance is not valid for unshielded network cables.
Liability
Every care has been taken in the preparation of this manual; if you detect any inaccuracies or omissions, please inform your
local Axis office, which can be found on the cover of this document. Axis Communications AB cannot be held responsible for
any technical or typographical errors and reserves the right to make changes to the product and manuals without prior
notice. Axis Communications AB makes no warranty of any kind with regard to the material contained within this document,
including, but not limited to, the implied warranties of merchantability and fitness for a particular purpose. Axis
Communications AB shall not be liable nor responsible for incidental or consequential damages in connection with the
furnishing, performance or use of this material.
Axis’ Trademarks
AXIS IP JumpStarter, AXIS ThinWizard, axinstall, AXIS Print Monitor, AXIS AddPrinter.
Other Trademark
Acknowledgments
Adobe Acrobat Reader, Aix, Apple, Debian, Ethernet, EtherTalk, IBM, LAN Manager, LAN Server, Macintosh, Microsoft, Novell
NetWare, OS/2, OS/400, AS/400, Red Hat, Solaris, SuSe, UNIX/Linux, Microsoft Windows, are registered trademarks of the
respective holders.
Support Services
Should you require technical assistance, please contact your Axis dealer. If your questions cannot be answered immediately,
your Axis dealer will forward your queries through the appropriate channels to ensure you a rapid response. On the Internet
you can find online manuals, technical support, software updates, application software, corporate information, etc..
Patent information
Axis AB has intellectual property rights relating to technology embodied in the product that is described in this document. In
particular, and without limitation, these intellectual property rights may include one or more of the patents listed at
http://www.axis.com/patent.htm and one or more additional patents or pending patent applications in the US and other
countries.
Software Acknowledgments
This product includes software developed by the OpenSSL Project for use in the OpenSSL Toolkit.
USER’S MANUAL AXIS 5570e/AXIS 5670e EN
Part No. 23956, Revision 2.1
Date: March 2006 - Copyright © Axis Communications AB
This manual applies to the AXIS 5570e/AXIS 5670e with firmware version 7.06 or higher.
2
AXIS 5570e / AXIS 5670e User’s Manual
Table of Contents
Table of Contents
Table of Contents . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3
Section 1
Introduction . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
About this Manual . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
About Axis . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Support Services . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Supported Environments . . . . . . . . . . . . . . . . . . . . . . . . .
Section 2
Product Overview . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8
Package Contents . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8
Protocols and Datastreams . . . . . . . . . . . . . . . . . . . . . . . 9
Physical Description . . . . . . . . . . . . . . . . . . . . . . . . . . . 10
AXIS Network Product CD . . . . . . . . . . . . . . . . . . . . . . . 12
Print Server Features and Benefits . . . . . . . . . . . . . . . . 12
Section 3
Basic Installation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Quick Overview . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Connect the Hardware . . . . . . . . . . . . . . . . . . . . . . . . .
Installation Guide . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Setting the IP Address . . . . . . . . . . . . . . . . . . . . . . . . . .
Dynamic IP Address Assignment . . . . . . . . . . . . . . . . . .
14
14
14
15
16
16
Section 4
Setting Up - AS/400 (iSeries) . . . . . . . . . . . . . . . . . . . . . . . . .
SNA Printing - 5494 Mode . . . . . . . . . . . . . . . . . . . . . .
TN5250E Printing (SCS over IP) . . . . . . . . . . . . . . . . . . .
PPR/PPD Printing - IPDS Data Streams . . . . . . . . . . . . .
22
22
29
31
Section 5
Setting Up - IBM Mainframe (zSeries) . . . . . . . . . . . . . . . . . .
SNA Printing . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
TCP/IP TN3270E Printing . . . . . . . . . . . . . . . . . . . . . . . .
PPR/PPD Printing - IPDS data streams . . . . . . . . . . . . . .
36
36
42
50
Section 6
Adding Printers in Windows . . . . . . . . . . . . . . . . . . . . . . . . . . 63
Adding Printers in Windows 2000 / XP / 2003 using AXIS
AddPrinter Wizard . . . . . . . . . . . . . . . . . . . . . . . . . . 64
Adding Printers in Windows 2000 / XP / 2003 using
Windows Add Printer Wizard . . . . . . . . . . . . . . . . . . 66
Adding Printers in Windows 2000 / XP / 2003 using the
Microsoft LPR Monitor . . . . . . . . . . . . . . . . . . . . . . . 72
Adding Printers in Windows NT Using the Microsoft LPR
Monitor . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 74
AXIS Print Monitor Software . . . . . . . . . . . . . . . . . . . . . 75
Adding Printers over TCP/IP in Windows NT using AXIS Print
Monitor . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 76
Adding NetBIOS/NetBEUI Printers in Windows 2000 using
AXIS Print Monitor . . . . . . . . . . . . . . . . . . . . . . . . . . 77
Adding Printers over NetBIOS/NetBEUI in Windows NT using
AXIS Print Monitor . . . . . . . . . . . . . . . . . . . . . . . . . . 78
Adding Printers in Windows 98 and Me over TCP/IP using
AXIS Print Monitor . . . . . . . . . . . . . . . . . . . . . . . . . . 79
AXIS 5570e / AXIS 5670e User’s Manual
6
6
6
7
7
3
Table of Contents
Adding Printers in Windows 98 and Me over
NetBIOS/NetBEUI using AXIS Print Monitor . . . . . . . 81
4
Section 7
Adding Printers in Macintosh . . . . . . . . . . . . . . . . . . . . . . . . .
Bonjour Printing in Mac OS X . . . . . . . . . . . . . . . . . . . .
Installation in Mac OS X using AppleTalk . . . . . . . . . . .
Installation of LPR printing in MAC OS X . . . . . . . . . . .
Installation on Mac OS 9.1 or older, using AppleTalk . . .
Choosing a Printer . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Section 8
Adding Printers in NetWare . . . . . . . . . . . . . . . . . . . . . . . . . . 89
Setup using NDPS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 89
Setup using iPrint . . . . . . . . . . . . . . . . . . . . . . . . . . . . 103
Basic Setup with AXIS NetPilot . . . . . . . . . . . . . . . . . . 108
Advanced Installation using AXIS NetPilot . . . . . . . . . 110
Basic Queue-based printing over IP . . . . . . . . . . . . . . . 112
Section 9
Adding Printers in UNIX/Linux . . . . . . . . . . . . . . . . . . . . . . .
Print Tools . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Typical Invocation via a Windows Manager . . . . . . . . .
Typical Invocation from a Terminal Window . . . . . . . .
Debian 3.0 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Red Hat 7.3 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
SuSE 8.0 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
AXIS axinstall Script . . . . . . . . . . . . . . . . . . . . . . . . . .
Print Methods on TCP/IP Networks . . . . . . . . . . . . . . .
Section 10
Adding Printers in OS/2 . . . . . . . . . . . . . . . . . . . . . . . . . . . . 125
TCP/IP Printing . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 125
NetBIOS/NetBEUI Printing in OS/2 . . . . . . . . . . . . . . . 126
Section 11
Management and Configuration . . . . . . . . . . . . . . . . . . . . . .
Using a Web Browser for Print Server Management . .
Using AXIS ThinWizard for Print Server Management .
Using FTP for Print Server Management . . . . . . . . . . .
Using Telnet . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Using SNMP . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Using Novell Utilities . . . . . . . . . . . . . . . . . . . . . . . . . .
Configuring the Print Server from an IBM Host . . . . . .
128
128
133
135
137
140
141
142
Section 12
Configuration Possibilities . . . . . . . . . . . . . . . . . . . . . . . . . .
Autodetect Printer Type . . . . . . . . . . . . . . . . . . . . . . . .
Auto-IP . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Changing Language in the Print Server’s Web Interface
145
E-mail Notification . . . . . . . . . . . . . . . . . . . . . . . . . . .
IPP (Internet Printing Protocol) . . . . . . . . . . . . . . . . . .
Logical Printers for Customized Printing . . . . . . . . . . .
Network Speed . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
NetWare Packet Signature Levels . . . . . . . . . . . . . . . .
Flash Loading of Firmware over the Web . . . . . . . . . . .
TCP/IP Restrictions . . . . . . . . . . . . . . . . . . . . . . . . . . .
144
144
144
..
82
82
84
84
85
85
115
115
116
117
118
119
121
122
123
145
146
154
161
162
162
163
AXIS 5570e / AXIS 5670e User’s Manual
Table of Contents
Enabling Secure Web Services — SSL/TLS . . . . . . . . . . 164
Enabling the SNMP3 Protocol . . . . . . . . . . . . . . . . . . . 167
Overriding Port Status . . . . . . . . . . . . . . . . . . . . . . . . . 168
Section 13
Upgrading the Firmware . . . . . . . . . . . . . . . . . . . . . . . . . . . 169
Upgrading the Firmware . . . . . . . . . . . . . . . . . . . . . . . 169
Obtaining the Software . . . . . . . . . . . . . . . . . . . . . . . . 171
Section 14
SNA Parameter Overview . . . . . . . . . . . . . . . . . . . . . . . . . . .
Communication Parameters . . . . . . . . . . . . . . . . . . . .
Updating parameters . . . . . . . . . . . . . . . . . . . . . . . . . .
Auto-configuration and Mapping . . . . . . . . . . . . . . . .
Section 15
SNA Gateways . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 177
Section 16
Extended IBM Printer Emulation . . . . . . . . . . . . . . . . . . . . . . 179
Section 17
IBM Fonts . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 182
Section 18
IBM Print Formatting . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 186
Section 19
IPDS Overview . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
IPDS Parameter Settings . . . . . . . . . . . . . . . . . . . . . . .
IPDS System Languages . . . . . . . . . . . . . . . . . . . . . . . .
IPDS Fonts . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Printer Resident Fonts . . . . . . . . . . . . . . . . . . . . . . . . .
Immediate Font Substitutions . . . . . . . . . . . . . . . . . . .
Unsupported Fonts . . . . . . . . . . . . . . . . . . . . . . . . . . .
Typographical Fonts . . . . . . . . . . . . . . . . . . . . . . . . . .
190
190
190
194
195
196
196
196
Section 20
DBCS Support . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Configuring the AS/400 Host, 5494 CU mode . . . . . . .
Configuring the Axis Network Print Server . . . . . . . . .
Verifying the Communications Link . . . . . . . . . . . . . . .
Amending Device Features . . . . . . . . . . . . . . . . . . . . .
Extended IBM Printer Emulation . . . . . . . . . . . . . . . . .
Font Tables . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
197
197
197
198
198
199
200
Section 21
Digital Copier Support . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 202
Section 22
IP Addressing . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 204
Section 23
The Test Button . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 208
Section 24
Troubleshooting . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 209
Section 25
Technical Specification . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 212
Section 26
The Parameter List . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
NetWare Parameter Combinations . . . . . . . . . . . . . . .
TCP Ports Opened for Raw Printing . . . . . . . . . . . . . . .
SNMP Device Index . . . . . . . . . . . . . . . . . . . . . . . . . . .
Section 27
Glossary . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 278
172
172
174
175
216
275
276
276
Index . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 284
AXIS 5570e / AXIS 5670e User’s Manual
5
Introduction
Section 1
Introduction
Thank you for purchasing the AXIS 5570e/AXIS 5670e print server. This
product has been developed to connect your printers anywhere in your
network, allowing all network users access to the shared printer resources.
The AXIS 5570e/AXIS 5670e is a LAN attached multi-protocol print
server that prints IBM and ASCII data streams to any ASCII printer.
Supporting IBM Mainframes, AS/400, NetWare, UNIX, LAN Server
Manager, Windows and Apple EtherTalk, these products are ideal for IBM
Mainframe and AS/400 sites that are migrating from pure IBM networks
to LAN environments.
About this Manual
This manual is applicable for the AXIS 5570e/AXIS 5670e with firmware
version 7.06 or higher, providing introductory information as well as
detailed instructions on how to set up and manage the print server in
various network environments. It is intended for everyone involved in
installing and managing the print server. To fully benefit from this
manual, you should be familiar with basic networking principles.
These instructions are based on the settings in a new and unconfigured
print server. To reload the default parameters, you can perform a Factory
Default, which will restore most of the settings. See “Performing a Factory
Default” on page 208.
About Axis
Axis increases the value of network solutions. The company is an
innovative market leader in network video and print servers. Axis'
products and solutions are focused on applications such as security,
surveillance, remote monitoring and document management. The
products are based on in-house developed chip technology, which is also
sold to third parties.
Axis was founded in 1984 and is listed on the Stockholmsbörsen
(XSSE:AXIS). Axis operates globally with offices in 14 countries and in
cooperation with distributors, system integrators and OEM partners in 70
countries. Markets outside Sweden account for more than 95 % of sales.
Information about Axis can be found at www.axis.com
6
AXIS 5570e / AXIS 5670e User’s Manual
Introduction
Support Services
Should you require any technical assistance, please contact your Axis
reseller. If your questions cannot be answered immediately, your Axis
reseller will forward your queries through the appropriate channels to
ensure a rapid response.
If you are connected to the Internet, you can:
•
•
•
•
Download user documentation and firmware updates
Find answers to previously resolved problems in the FAQ database.
Search by product, category or phrase
Report problems to Axis support staff by logging in to your private
support area
Visit the Axis support Web at www.axis.com/techsup
Supported Environments
The Axis Network Print Server is the ideal print server in mixed
environments as it can communicate with all the major computer systems
and network protocols including:
•
•
•
•
•
•
•
IBM Mainframe and AS/400
Windows
NetWare
UNIX
Windows clients connected to LANtastic networks
Macintosh
Internet via any standard Web browser
AXIS 5570e / AXIS 5670e User’s Manual
7
Product Overview
Section 2
Product Overview
Package Contents
Verify that nothing is missing from the AXIS 5570e/AXIS 5670e package
by using the check list below. Please contact your dealer if anything is
missing or damaged. All packing materials are recyclable.
AXIS 5570e & AXIS 5670e
Axis Print Server
Model
TCP/IP
AXIS 5570e
IPDS SNA
AXIS 5670e
Part Number
Power Adapter
0188-001-02
0188-001-03
0193-001-02
PS-H
0193-001-03
TCP/IP
0189-001-01
IPDS SNA
0194-001-01
Item
Title
Part Number
CD
AXIS Network Product CD
22964
Warranty Sheet
Warranty Axis Servers (USA)
Warranty Axis Servers (other countriesI
21681
21680
Printed Material
AXIS 5570e/AXIS 5670e User’s Guide
20896
Adhesive Holder & Clip*
ACC AXIS 5500 CLIPS K
20119
USB Cable
only supplied with AXIS 5570e*
70 cm
20208
* Only supplied with AXIS 5570e. Note: The USB cable supports USB
Low-Speed and Full-Speed. Hi-Speed is not supported.
8
AXIS 5570e / AXIS 5670e User’s Manual
Product Overview
Protocols and Datastreams
The AXIS 5570e/AXIS 5670e is available in two versions; IPDS SNA and
TCP/IP. The tables below display the functionality of each version.
AXIS 5570e
AXIS 5570e
IPDS SNA (part no. 0193)
IPDS support
Digital Copier Support
•
•
•
•
•
•
•
AXIS 5670e
IPDS SNA (part no. 0194)
IPDS support
•
•
•
•
•
•
•
SCS support
3270DS support
TN3270E
TN5250E
SNA support
TCP/IP (part no. 0188)
•
•
•
•
AXIS 5670e
SCS support
3270DS support
TN3270E
TN5250E
SNA support
Digital Copier Support
TCP/IP (part no. 0189)
•
•
•
•
Note:
All models may not be available in all countries in which Axis operates. Please contact your
local sales representative for more information.
AXIS 5570e / AXIS 5670e User’s Manual
9
Product Overview
Physical Description
AXIS 5570e
LPT1
Test Button
Network Indicator
Ethernet Connector
USB1
Power Connector
Power Indicator
Mounting the AXIS
5570e
Using the supplied clip and holder, the AXIS 5570e can be mounted e.g.
on the back of the printer or on a wall.
Adhesive Clip
Fasten to print server
by peeling off adhesive
tape.
Adhesive Holder
Fasten to mounting
surface by peeling off
adhesive tape.
AXIS 5670e
10
AXIS 5570e / AXIS 5670e User’s Manual
Product Overview
Backside Label on
Print Server
Serial number
Network Connector
The AXIS 5570e/AXIS 5670e is designed for 10baseT Ethernet or 100base
TX Fast Ethernet networks and is connected to the network via a standard
RJ-45 (Category 5 or 6 twisted pair) cable.
Printer Ports
AXIS 5570e
AXIS 5570e is equipped with one USB port that is USB 1.1 and 2.0 Lowand Full-Speed compliant, and one high-speed IEEE 1284 compatible
parallel port.
AXIS 5670e
AXIS 5670e is equipped with two high-speed IEEE 1284 compatible
parallel ports and one RS232 serial port.
Test Button
The test button is used for:
Printing a test page to check the connection to the printer.
Printing the parameter list showing the print server settings.
Performing a Factory Default of the print server, which will restore
most of the parameters and settings to their factory default values.
See Performing a Factory Default, on page 208.
•
•
•
Network Indicator
Power Indicator
The network indicator flashes to indicate network activity.
The power indicator is lit while power is applied. If it is not lit, or if it
flashes, there is a problem with the print server or its Power Adapter.
Compatible Printers
Any standard printer can be used except host-based printers (also known
as CAPT,GDI, PPA or Windows-based printers).
Configuration and
Management
The print server can be configured and managed from its internal Web
pages, using HTTP as well as HTTPS in the secure mode. These Web pages
offer you a platform independent management tool that is suitable for all
supported network environments. See Using a Web Browser for Print
Server Management, on page 128.
AXIS 5570e / AXIS 5670e User’s Manual
11
Product Overview
AXIS Network Product CD
The AXIS Network Product CD provides an easy-to-use electronic catalog,
that includes Axis software, firmware and user documentation. If your
computer is set to French, German, Italian or Spanish, the information
will automatically be presented in that language, otherwise you will see
the English version.
To read the PDF documents you need an Acrobat Reader, which can be
fetched at http://www.adobe.com/products/acrobat/readermain.html
Start-up Procedures
for Windows
If your computer is configured to autostart CDs, the AXIS Network
Product CD will start automatically when inserted into a local CD drive on
Windows 98, Me, NT, 2000 and XP platforms. You can also navigate to
the CD root directory and start the index.htm file from within the
Windows file manager.
Start-up Procedures
for UNIX/Linux,
and Mac OS
Using your preferred file manager application, navigate to the CD root
directory and click index.htm
Latest Versions
The latest version of Axis documentation, software and firmware is
available on www.axis.com
Print Server Features and Benefits
Reliability
The Axis Network Print Server print server provides high performance
and reliability combined with low power consumption. The electronic
circuits are based on the AXIS ETRAX 100LX chip, which comprises an
integrated 32 bit RISC processor and associated network controllers.
Flexibility
In the IBM Mainframe and AS/400 environment, the Axis Network Print
Server can emulate IBM twinax and coax print and control functionality.
This means that the Axis Network Print Server can effectively replace
coax/twinax attached printers and control units on the LAN.
It supports printing in all the major computer systems and environments,
including five different print methods in the TCP/IP environment. The
integrated IPP (Internet Printing Protocol) function allows for printing
from LAN to LAN via a WAN, such as the Internet.
Speed
Easy to Install
12
The AXIS ETRAX 100LX chip has been specifically designed for LAN
products. It supports data transfer rates of up to 200 Mbit/s (100 Mbit
Ethernet full duplex). High speed Centronics communication such as ECP,
Hewlett-Packard Fast Mode, High Speed and IBM Fast Byte is supported.
The print server installs, operates and is managed in a reliable and easy
fashion.
AXIS 5570e / AXIS 5670e User’s Manual
Product Overview
Security
Monitoring
You can assign a password to restrict login and printer access. It is also
possible to disable protocols and to configure a secure mode (https). See
“Enabling Secure Web Services — SSL/TLS” on page 164.
The internal print server Web pages and AXIS ThinWizard (3.04 and up)
allow you to continuously monitor printer status. The Web pages are used
to monitor single Axis units while AXIS ThinWizard can be used to
monitor multiple Axis units. Integrity of your printing is also monitored
via interactive communication with the IBM host.
The AXIS 5570e/AXIS 5670e additionally supports SNMP for remote
monitoring.
Futureproof
NetWare Packet
Signature
The firmware stored in the print server Flash memory can be upgraded
over the network. This allows you to quickly update and enhance its
operational features when new print server software becomes available.
See “Upgrading the Firmware” on page 169.
The print server supports NetWare Packet Signature Level 1, 2, 3, which
protects servers and clients using the NetWare Core Protocol services.
NCP packet signature prevents packet forgery by requiring the server and
the client to sign each NCP packet. See your Novell NetWare
documentation for detailed information.
AXIS 5570e / AXIS 5670e User’s Manual
13
Basic Installation
Section 3
Basic Installation
Quick Overview
Follow these steps to make your printer network ready:
1. Connect the Hardware, on page 14
2. Setting the IP Address, on page 16
3. “Installation Guide” on page 15
Connect the Hardware
1. Make sure that the printer is switched off and that the Power Adapter is
disconnected from the print server.
2. Locate the serial number, found on the underside label of the print server,
and write it down. Example: S/N: 00408c181cf0
3. Connect the printer(s) to the print server.
4. Connect the print server to the network (Ethernet Connector) using a
twisted pair RJ45 cable (of category 5 or better).
5. Switch on the printer and make sure it is ready for printing (display showing
“Online”, “Ready”, etc.).
6. Connect the Power Adapter to the print server. The power indicator lights
up. If the network indicator starts to flash, the print server is correctly
connected to the network.
7. Wait 1 minute and press the test button once. A test page will be printed
on the connected printer — keep it handy during the installation. The test
page will show the assigned IP address of the print server.
The print server can now be installed in your network using one of the
methods detailed in the Installation Guide, on page 15.
Notes:
14
•
The test page includes a list of the most important parameters, including the network
speed and the firmware version number.
•
Each print server is pre-configured with a unique node address that is identical to the
serial number. The node address can be changed using any standard Web browser. Please
refer to Management and Configuration, on page 128, for more information.
•
The AXIS 5570e/AXIS 5670e uses high speed Centronics communication. For use with
older printers not supporting high speed, this function can be disabled by using any
standard Web browser. Please refer to “Management and Configuration” on page
128, for more information.
AXIS 5570e / AXIS 5670e User’s Manual
Basic Installation
Installation Guide
After connecting the Axis Network Print Server to your network, you are
now ready to perform the basic setup procedures. The method of
installation that you choose should be dictated by your printing
requirements and the type of network into which you are integrating.
1. Start out with setting an IP address on the print server, described in
“Setting the IP Address” on page 16.
2. Refer to the table below to determine which setup procedures that are
relevant to your network environment.
Network
Configuration
Actions
SCS / IPDS
SNA
“SNA Printing - 5494 Mode” on page 22
SCS
TN5250E (TCP/IP)
“TN5250E Printing (SCS over IP)” on page 29
IPDS
PPR/PPD (TCP/IP)
“PPR/PPD Printing - IPDS Data Streams” on
page 31
SNA
“SNA Printing” on page 36
TN3270E (TCP/IP)
“TCP/IP TN3270E Printing” on page 42
PPR/PPD (TCP/IP)
“PPR/PPD Printing - IPDS data streams” on
page 50
Windows
98/NT/Me/2000/XP/2003
TCP/IP,
NetBIOS/NetBEUI
“Adding Printers in Windows” on page 63
NetWare
TCP/IP
IPX/SPX
“Adding Printers in NetWare” on page 89
Macintosh
TCP/IP, AppleTalk
“Adding Printers in Macintosh” on page 82
TCP/IP
“Adding Printers in UNIX/Linux” on page
115
TCP/IP
“TCP/IP Printing” on page 125
NetBIOS/NetBEUI
“NetBIOS/NetBEUI Printing in OS/2” on page
126
Environment
AS/400
Data
Stream
SCS / IPDS
IBM
Mainframe
IPDS
UNIX
OS/”
Installation Tools
The recommended installation tools and management methods for the
Axis Network Print Server are summarized here:
Protocols
TCP/IP
Operating Systems
Configuration method
Management method
Windows
2000/XP/2003
AXIS AddPrinter Wizard
Web browser, FTP, Telnet, SNMP
AXIS ThinWizard
Windows 98/NT/Me
AXIS Print Monitor software and
Windows Add Printer Wizard
Web browser, FTP, Telnet, SNMP
Mac OS X
Native Mac OS X tool
Web browser
UNIX
Native Unix/Linux tools
Web browser, FTP, Telnet, SNMP
IPX/SPX
NetWare
Novell Utilities
Novell Utilities
NetBIOS
NetBEUI
Windows 95/98
NT/Me/2000/2003
AXIS Print Monitor
Web browser. FTP, Telnet, SNMP
AppleTalk
Macintosh
Bonjour, Web browser, Mac-FTP
Web browser, Mac-FTP
AXIS 5570e / AXIS 5670e User’s Manual
15
Basic Installation
Setting the IP Address
Dynamic IP Address
Assignment
Method
Server required
Comment
See “Adding Printers in Windows 2000 / XP / 2003 using AXIS AddPrinter Wizard” on page 64
AXIS AddPrinter Wizard
DHCP
DHCP server
Dynamic assignment of IP addresses.
See Dynamic IP Address Assignment, on page 16
RARP
RARP server
Static assignment of IP addresses. Cannot be used
over routers.
See Dynamic IP Address Assignment, on page 16
BOOTP
BOOTP server
Static assignment of IP addresses.
See Dynamic IP Address Assignment, on page 16
Auto-IP
No server required.
Automatic assignment of IP addresses for Windows
environments.
See Dynamic IP Address Assignment, on page 16
Manual IP Address
Assignment
Method
Platform
Windows
arp/ping
UNIX
Mac OS X
AXIS
AddPrinter Wizard
AXIS
ThinWizard
Comment
See
Requires the IP address for each
device to be downloaded
individually.
Cannot be used over routers.
Setting the IP Address
using arp/ping, on
page 18
You must define the Default
Router and Subnet Mask. Log in
to the print server’s Web pages
and select Admin | Network
Settings | Detailed View |
TCP/IP Network| Default
Router and Subnet Mask.
DHCP, Auto-IP, BOOTP and
RARP must first be set to No
Setting the IP Address
using arp/ping, on
page 18
Windows
2000, XP, 2003
Axis software that allows you to find
print servers in your network and assign an IP address to them.
Adding Printers in
Windows 2000 / XP /
2003 using AXIS AddPrinter Wizard, on
page 64
Windows
2000/XP
Axis software that assists in setting
the IP address of multiple print servers simultaneously. This software is
recommended for large organizations
and enerprise networks.
Using AXIS ThinWizard for Print Server
Management, on
page 133
Dynamic IP Address Assignment
Obtaining an IP
Address through
DHCP
16
If you have a DHCP server on your network, your print server will
receive an IP address automatically. The IP address will then appear on
the test page printed when you press the test button once.
You should now be able to access the print server’s internal Web pages as
described on Accessing the Web Pages, on page 129
AXIS 5570e / AXIS 5670e User’s Manual
Basic Installation
If you are not working in a DHCP network, you need to set the IP
address of the print server manually. See “Manual IP Address
Assignment” on page 16.
Obtaining an IP
Address through
Auto-IP
Important:
Auto-IP may be used to set the IP address automatically in the absence of
a DHCP server.
The default Auto-IP address structure is: 169.254.xxx.xxx.
The Auto-IP function will only function when the DHCP parameter is
enabled in the print server.
This function is enabled automatically upon installation of a brand new
print server. If you perform a Factory Default using the test button on the
print server and you do not have a DHCP server on your network, Auto-IP
will automatically set the IP address of the print server.
The DHCP Enabled parameter is enabled/disabled in the print server’s
Web pages: Admin => Network Settings => Detailed View => TCP/IP
Network => DHCP Enabled: Yes/No.
Notes:
Manual IP Address
Assignment
•
Use a Web browser with JavaScript support and Java enabled.
•
The Axis Network Print Server supports WINS (Windows Internet Name Service), which is
recommended when setting the IP address using DHCP in Windows environments.
•
If you are working in a WINS/ DDNS network, you can access the print server’s Web pages
using its default host name: In the Web browser’s Location/Address field, enter the
default print server name AXISxxxxxx (xxxxxx are the last six digits of the serial number,
found on the print server’s underside label). Example: If the serial number is 00 40 8c 18
16 36, type AXIS181636 and press Enter.
•
DHCP, RARP and BOOTP can be used to set the IP address in UNIX.
•
If you are working in a network that does not use dynamic IP address assignment, refer to
“Manual IP Address Assignment” on page 16 to assign an IP address to the print server
manually.
To establish communication with the TCP/IP network, an IP address must
be assigned to your Axis Network Print Server. Choose the appropriate
method according to your network:
• arp/ping - use this method to set the IP address for each new print
server individually.
This method cannot be used over routers.
Refer to “Setting the IP Address using arp/ping” on page 18.
• AXIS ThinWizard software is the primary recommended tool for
large organizations.
It can set IP addresses, discover and group print servers, install new
firmware and configure multiple Axis products concurrently.
Refer to “Using AXIS ThinWizard for Print Server Management” on
page 133
AXIS 5570e / AXIS 5670e User’s Manual
17
Basic Installation
Note:
If you are using host names, you can map a unique host name to the IP address. Refer to your
system manuals for instructions on how this is performed on your system.
Setting the IP Address
using arp/ping
Refer to the appropriate section below to assign an IP address to your
Axis Network Print Server using arp/ping:
Windows
Open a Command Prompt and enter the following syntax:
Syntax
1.
2.
arp -s <Internet address> <Ethernet address>
ping <Internet address>
Example
arp -s 192.168.3.191 00-40-8c-18-16-36
ping 192.168.3.191
The host will return reply from 192.168.3.191, or a similar message. This
indicates that the address has been set and that communication is
established. You are now ready to print.
UNIX, Mac OS X
Open a Terminal and enter the following syntax:
Syntax
1.
2.
arp -s <Internet address> <Ethernet address>
ping <Internet address>
Example
arp -s 192.168.3.191 00:40:8c:18:16:36
ping 192.168.3.191
The host will return psname is alive, or a similar message. This indicates
that the address has been set and that communication is established. You
are now ready to print.
Important!
You must define the Default Router and Subnet Mask when you set a static IP address. Log
in to the print server’s Web pages and select Admin | Network Settings | Detailed View |
TCP/IP Network | Default Router and Subnet Mask.
DHCP, Auto-IP, BOOTP and RARP must first be set to No!
Notes:
Using RARP in
UNIX/Linux
18
•
The Ethernet address is equal to the serial number, which is located on the underside
label of the AXIS 5570e/AXIS 5670e.
•
The arp command varies between different UNIX systems. Some BSD type systems
expect the host name and node address in reverse order. Furthermore IBM AIX systems
will require the additional argument ether.
Example:
arp -s ether <host name> 00:40:8c:10:00:86 temp
•
When you execute the ping command for the first time, you may experience a
significantly longer response time than usual.
•
The ability to set the IP address with ARP and PING will only be enabled the first 10
minutes after restarting the print server.
Follow the instructions below to set the IP address using RARP.
AXIS 5570e / AXIS 5670e User’s Manual
Basic Installation
1. Append the following line to your Ethernet Address table. This is typically
located in the /etc/ethers file:
<Ethernet address> <host name>
Example:
00:40:8c:10:00:86 npsname
2. Update, if necessary, your host table and alias name databases, as required
by your system.
3. If it is not already running, start the RARP daemon. This is typically
performed using the rarpd -a command.
4. Restart the AXIS 5570e/AXIS 5670e to download the IP address.
Notes:
Using BOOTP
in UNIX/Linux
•
The Ethernet address is equal to the serial number, which can be found on the underside
label of the AXIS 5570e/AXIS 5670e.
•
If you are a IBM AIX user, you will probably not have access to a RARP daemon. If this is
the case, you can use either the arp or BOOTP methods instead.
Follow the instructions below to set the IP address using BOOTP:
1. Append the following entry to your boot table. This is typically performed
by editing the file: /etc/bootptab
<host name>:ht=<hardware type>:vm=<vendor magic>:\
:ha=<hardware address>:ip=<IP address>:\
:sm=<subnet mask>:gw=<gateway field>
Example:
npsname:ht=ether:vm=rfc1048:\
:ha=00408c100086:ip=192.168.3.191:\
:sm=255.255.255.0:gw=192.168.1.1
The Axis Network Print Server can automatically download a customized
config file from a TFTP server. Just add the name of the config file and
the TFTP server’s IP address to your boot table. The config file is
downloaded immediately after the Axis Network Print Server receives its
IP address.
AXIS 5570e / AXIS 5670e User’s Manual
19
Basic Installation
Notes:
Managing DHCP
•
The Axis Network Print Server supports WINS (Windows Internet Name Service), which is
recommended when setting the IP address using DHCP in Windows environments.
•
The Ethernet Address is the same as the serial number, found on the print server’s underside label. Enter the Ethernet Address in the same format as in the example above.
•
Setting the IP address with arp and ping is only possible in the first 10 minutes after
re-booting the print server.
•
When you execute the ping command for the first time, you may experience a significantly longer response time than usual.
•
The arp command varies between different UNIX systems.
•
You need root privileges on your UNIX system in order to execute the arp command and
run axinstall .
•
Some BSD type systems expect the host name and serial number in reverse order. Furthermore IBM AIX systems will require the additional argument ether.
Example: arp -s ether <host name> <Ethernet Address> temp
Follow the instructions below to download the IP address using DHCP:
1. Edit or create a scope in the DHCP manager of the DHCP daemon. The
entries included in this scope should contain the following parameters:
• range of IP addresses
• subnet mask
• default router IP address
• WINS server IP address(es)
• lease duration
2. Activate the scope.
The Axis Network Print Server will automatically download the DHCP
parameters.
If you are using WINS, you must include at least one WINS server IP
address in the DHCP scope. Immediately after the IP address has been
received, the Axis Network Print Server registers its host name and IP
address on the WINS server.
The Axis Network Print Server can automatically download a customized
config file from a TFTP server. Just add the name of the config file and
the TFTP server’s IP address to your DHCP scope. The config file is
downloaded immediately after the Axis Network Print Server receives its
IP address.
20
System Privileges
You need root privileges on your UNIX system, or administrator
privileges on a Windows NT server.
Ethernet Address
You need to know the Ethernet address of your AXIS 5570e/AXIS 5670e
to perform the installation. The Ethernet address is based upon the serial
number of your print server. This means, for example, that a print server
with the serial number 00408C100086, will have the corresponding
Ethernet address of 00 40 8C 10 00 86. The serial number is located on
the underside label of the print server.
AXIS 5570e / AXIS 5670e User’s Manual
Basic Installation
IP Address
If you do not have a DHCP server on your network, you must obtain an
unused IP address from your network administrator.
Important:
DO NOT use the IP addresses used in the following examples when installing your Axis
Network Print Server. Always consult your network administrator before assigning an IP
address to your Axis Network Print Server.
Registering and
Resolving
Host Names
In order to register the host name of the Axis Network Print Server in
networks with dynamic IP address settings, WINS (Windows Internet
Name Service) and DDNS (Dynamic Domain Naming System) are
supported. It is recommended that at least one of these methods be used
when setting the IP address of the Axis Network Print Server using DHCP.
The host name of the Axis Network Print Server is specified by the
PS_NAME parameter. Refer to The Parameter List, on page 216.
WINS Host Name
Rules
WINS only supports 15 character long host names. If your host name is
longer than 15 characters, the Axis Network Print Server truncates the
host name to 15 characters when registering with a WINS server. You can
view the Axis Network Print Server host name that is registered at a
WINS server, in the print server’s Web interface. Refer to Section 11
Management and Configuration, on page 128.
DDNS Host Name
Rules
DDNS supports 53 character long host names, but they can only consist
of the characters ‘A-Z’, ’a-z’ and ‘-’. If your host name consists of any
other characters, they are converted to ‘-’, when registering with a DDNS
server. You can view the Axis Network Print Server host name that is
registered at a DDNS server, in the print server’s Web interface. Refer to
Section 11 Management and Configuration, on page 128.
If the host name matches another entry in the DDNS data base, the Axis
Network Print Server deletes the entry before registering.
Notes:
•
The host name limitations conclude that if you want to register the same host name at a
WINS server and a DDNS server, the host name should be no longer than 15 characters
and it should only contain the characters:
‘A - Z’, ‘a-z’ and ‘-’
•
Refer to your system manuals or to your network administrator for instructions on how
host name resolutions are performed on your system.
•
If the host name has not been mapped to the IP address, you can still perform the
following instructions on how to download the IP address. In this case, simply replace
the host name entry with the IP address wherever required.
AXIS 5570e / AXIS 5670e User’s Manual
21
Setting Up - AS/400 (iSeries)
Section 4
Setting Up - AS/400 (iSeries)
This section describes how to configure the Axis Network Print Server for
printing SCS and IPDS data streams using SNA and TCP/IP transport
protocols in the AS/400 (iSeries) environment.
Note:
SNA is only available for print server models with the SNA option installed. Please refer to
Protocols and Datastreams, on page 9
A number of protocols and print methods are available. Looking at SCS
over TCP/IP printing, we strongly recommend the TN5250E alternative.
This print method offers superior control and management features as
well as automatic configuration and high throughput using the Axis
Network Print Server.
If you have decided to use SNA, we recommend the 5494 mode.
Compared to the 3174 mode, this alternative yields better text formatting
options as well as automatic configuration.
Proceed to the setup section that is relevant to your network
environment, as described in the table below:
Printing
protocol
Data
streams
SNA - 5494
Mode
IPDS
SCS
Action
Comment
SNA Printing - 5494 Mode, on page 22
Recommended method
for SNA
TN5250E
(TCP/IP)
SCS
TN5250E Printing (SCS over IP), on page
29
Recommended method
for SCS over TCP/IP
PPR/PPD (TCP/IP)
IPDS
PPR/PPD Printing - IPDS Data Streams,
on page 31
Recommended method
for IPDS over TCP/IP
If you intend to operate your Axis Network Print Server in a multiprotocol environment, you should also proceed to the other relevant
sections in this manual.
SNA Printing - 5494 Mode
The 5494 mode provides a significantly richer set of features for
formatting text and is the recommended emulation mode in AS/400
environments.
The 5494 mode supports DBCS which accommodates printing from
AS/400 host systems using languages that employ double-byte character
sets, namely Chinese, Japanese and Korean. Refer to DBCS Support, on
page 197 for further information.
The AXIS print server supports printing SCS and IPDS data streams via
the SNA transport protocol.
22
AXIS 5570e / AXIS 5670e User’s Manual
Setting Up - AS/400 (iSeries)
Note:
SNA is only available for print server models with the SNA option installed. Please refer to
Protocols and Datastreams, on page 9.
Configuring for SNA printing in 5494 Mode is described in three separate
stages:
•
•
•
The AS/400 Host
System Checklist
The AS/400 Host System Checklist
Configuring the Axis Network Print Server
Verifying the communication
If you are using AS/400 Version 3 Release 1 or higher, the AS/400 host in
5494 CU mode is automatically configured. The instructions in this
section describe this automated configuration procedure.
If you are using a pre-version 3 release, you must perform the
configuration procedure manually. If this is the case, please refer to the
Axis Web site for further documentation.
Note:
You will find an AS/400 Parameter checklist in the AXIS 5570e/AXIS 5670e User’s Guide
where you can enter the values described in this section for future reference.
1. Type DSPNETA on the AS/400 command line and press Enter. For future
reference, note the values of the Local network ID and Default local
location parameters. Press F3.
Example:
DSPNETA
Display Network Attributes
System:
S1032BB0
Current system name . . . . . . . . . .
Pending system name . . . . . . . . . .
Local network ID . . . . . . . . . . . .
Local control point name . . . . . . . .
Default local location . . . . . . . . .
Default mode . . . . . . . . . . . . . .
APPN node type . . . . . . . . . . . . .
Data compression . . . . . . . . . . . .
Intermediate data compression . . . . .
Maximum number of intermediate sessions
Route addition resistance . . . . . . .
Server network ID/control point name . .
*ANY
Press Enter to continue.
F3=Exit
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
:
S1032BB0
:
: > APPN
:
S1032BB0
: > S1032BB0
:
BLANK
:
*ENDNODE
:
*NONE
:
*NONE
:
200
:
128
:
*LCLNETID
More...
F12=Cancel
The required parameter values are highlighted in bold.
2. Type WRKLIND *ELAN and press Enter:
to get a list of all line descriptions on the system. Type 5 in front of the line
description and press Enter.
AXIS 5570e / AXIS 5670e User’s Manual
23
Setting Up - AS/400 (iSeries)
3. Press F11 to display keywords.
Display Line Description
S44A6643
Line description . . .: LIND
Option . . . . . . . .: OPTION
Category of line . . .:
Resource name . . . .:
Online at IPL . . . . :
Vary on wait . . . . .:
Network controller . .:
Local adapter address :
Exchange identifier . :
Ethernet standard . .:
Line speed . . . . . .:
Enable only for TCP/IP:
Current line speed . .:
Duplex . . . . . . . .:
Current duplex . . . .:
Maximum controllers. .:
ETHLINE
*BASIC
*ELAN
RSRCNAME
ONLINE
VRYWAIT
NETCTL
ADPTADR
EXCHID
ETHSTD
LINESPEED
TCPONLY
DUPLEX
MAXCTL
More...
Press Enter to continue.
F3=Exit
LIN061
*YES
*NOWAIT
ETHLINET
08005AB77D49
056A6643
*ALL
10M
*NO
10M
*HALF
*HALF
50
F11=NonDisplay keywords
F12=Cancel
4. For future reference, note the values of the Local Adapter Address
(ADPTADR) and Maximum Controllers (MAXCTL) parameters. Press Enter
to view the active switched controllers display.
Display Line Description
S44A6643
Line description . . : LIND
Option . . . . . . . : OPTION
Category of line . . :
ETHERNET
*ACTSWTCTL
*ELAN
--------------Active Switched Controllers-------CONTROLER1
CONTROLER2
CONTROLER3
Press Enter to continue.
F3=Exit
Bottom
F11= Nondisplay keywords
F12=Cancel
5. Press Enter to display the SSAP list. Make sure that there is at least one SSAP
entry dedicated for SNA. For your future reference, note the SSAP value for
this entry.
Verify that the number of controllers displayed on this screen does not
exceed the value for maximum controllers (MAXCTL) from above.
24
AXIS 5570e / AXIS 5670e User’s Manual
Setting Up - AS/400 (iSeries)
Display Line Description
S44A6643
Line description .: LIND
Option . . . . . : OPTION
Category of line .:
SSAP List. . . . .: SSAP
----Source Service Access
SSAP
Maximum Frame
04
1496
12
1496
AA
1496
C8
1496
08
1496
ETHLINE
*SSAP
*ELAN
Points-----Type
*SNA
*NONSNA
*NONSNA
*HPR
*SNA
Press Enter to continue.
F3=Exit
Bottom
F11=Nondisplay keywords
F12=Cancel
Note:
The SNA entry is normally set to SSAP 04.
6. Press Enter to display the Autocreate controller (AUTOCRTCTL)
parameter. Ensure that the AUTOCRTCTL parameter is set to *YES. Press F3
to return to the command line.
Display Line Description
S44A6643
Line description . . :
Option . . . . . . . :
Category of line . . :
LIND
OPTION
ETHERNET
*APPN
*ELAN
Link speed . . . . .:
Cost/connect time . .:
Cost/byte . . . . . :
Security for line. . :
Propagation delay. . :
User-defined 1 . . . :
User-defined 2 . . . :
User-defined 3 . . . :
Autocreate controller:
Autodelete controller:
LINKSPEED
COSTCNN
COSTBYTE
SECURITY
PRPDLY
USRDFN1
USRDFN2
USRDFN3
AUTOCRTCTL
AUTODLTCTL
10M
0
0
*NONSECURE
*MIN
128
128
128
*YES
1440
Press Enter to continue.
F3=Exit
F11=Nondisplay keywords
Bottom
F12=Cancel
7. Type DSPSYSVAL QCHRID on the command line and press Enter. Note the
code page for future reference. Press F3 to exit.
AXIS 5570e / AXIS 5670e User’s Manual
25
Setting Up - AS/400 (iSeries)
8. Type DSPSYSVAL QAUTOCFG on the command line and press Enter. Make sure
the Autoconfigure device parameter is turned on (1). Press F3 to exit.
Display System Value
System value . . . . . :
Description . . . . . :
QAUTOCFG
Autoconfigure devices
Autoconfigure device . :
1
0=Off
1=On
9. Type DSPSYSVAL QAUTORMT on a command line and press Enter. Make sure
the Autoconfigure remote controller parameter is turned
on(1). Press F3 to exit.
Display System Value
System value . . . . . :
Description . . . . . :
QAUTORMT
Autoconfigure of remote controllers
Autoconfigure remote controller :
1
0=Off
1=On
10. Type DSPMODD QRMTWSC on the command line and press Enter. Press F11 to
display the keywords. Verify that the mode description exists on the system
and that it is configured as presented in the example below. Use the
command
WRKMODD QRMTWSC if you need to change a value.
Press F3.
Display
Mode
Mode
Description
description
.
.
.
.
S44A6643
.
.
.
:MODD
QRMTWSC
Class-of-service . . . . . . . :COS
Maximum sessions . . . . . . . :MAXSSN
Maximum conversations. . . . . :MAXCNV
Locally controlled sessions. . :LCLCTLSSN
Pre-established sessions. . . .:PREESTSSN
Maximum inbound pacing value. .:MAXINPAC
Inbound pacing value . . . . . :INPACING
Outbound pacing value
. . . . :OUTPACING
Maximum length of request unit.:MAXLENRU
Data compression . . . . . . . :DTACPR
Inbound data compression . . . :INDTACPR
Outbound data compression
. . :OUTDTACPR
Session level encryption . . . :SLE
Text . . . . . . . . . . . . . :TEXT
is IBM Supplied
Press
F3=
26
Enter
Exit
to
continue.
#CONNECT
57
57
56
0
*CALC
7
7
*CALC
*NETATR
*RLE
*RLE
*NONE
This Mode
Bottom
F11=Nondisplay
keywords
F12=Cancel
AXIS 5570e / AXIS 5670e User’s Manual
Setting Up - AS/400 (iSeries)
11. Type DSPUSRPRF QUSER and press Enter. Make sure that the QUSER Status
is *ENABLED.
Display User Profile - Basic
User profile . . . . . . . .
Previous sign-on . . . . . .
Sign-on attempts not valid .
Status . . . . . . . . . . .
Date password last changed .
Password expiration interval
Set password to expired . .
User class . . . . . . . . .
Special authority . . . . .
Group profile . . . . . . .
Owner . . . . . . . . . . .
Group authority . . . . . .
Group authority type . . . .
Supplemental groups . . . .
Assistance level . . . . . .
Current library . . . . . .
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
:
:
:
:
:
:
:
:
:
:
:
:
:
:
:
:
QUSER
0
*ENABLED
08/08/00
*SYSVAL
*NO
*USER
*NONE
*NONE
*USRPRF
*NONE
*PRIVATE
*NONE
*SYSVAL
*CRTDFT
More...
12. Page forward to the next screen by pressing Enter and verify that the
Maximum Storage Allowed parameter is set to *NOMAX. Press F3.
Display User Profile - Basic
User profile . . . . . . . . . . . . . . . :
QUSER
Initial program .
Library . . . .
Initial menu . . .
Library . . . .
Limit capabilities
Text . . . . . . .
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
:
:
:
:
:
:
*NONE
Display sign-on information
Limit device sessions . . .
Keyboard buffering . . . . .
Maximum storage allowed . .
Storage used . . . . . . .
Highest scheduling priority
Job description . . . . . .
Library . . . . . . . . .
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
:
:
:
:
:
:
:
:
*SYSVAL
*SYSVAL
*SYSVAL
*NOMAX
832
3
QDFTJOBD
QGPL
MAIN
*LIBL
*NO
Work Station User
More...
Press Enter to continue.
F3=Exit
F12=Cancel
Use the command WRKCFGSTS *CTL xxxx* (where xxxx is the first 4
characters of the Axis Network Print Server 5494 LU Name)and press
Enter to delete any previously created Controller and Device descriptions
specific to your Axis Network Print Server. Delete the Device Descriptions
(indented text) first and then the Controllers. Print a test page if you are
unsure of the Axis Network Print Server 5494 LU Name.
Work with Configuration Status
Position to
. . . . .
S1032BB0
Starting characters
Type options, press Enter.
1=Vary on
2=Vary off
5=Work with job
8=Work with description
9=Display mode status
13=Work with APPN status...
Opt
Description
FSIOP
ETHERNET
AXIS11
AXIS11
AXIS11
AXIS11
AXIS11
AXIS11
AXIS 5570e / AXIS 5670e User’s Manual
Status
ACTIVE
ACTIVE
ACTIVE
ACTIVE
ACTIVE/TARGET
ACTIVE/SOURCE
ACTIVE/SOURCE
ACTIVE/SOURCE
-------------Job--------------
SHEILA
SHEILA
SHEILA
SHEILA
QUSER
QUSER
QUSER
QUSER
010190
010190
010190
010190
27
Setting Up - AS/400 (iSeries)
Configuring the
Axis Network Print
Server
To perform the instructions presented in this section, you should first
assign an IP address to your Axis Network Print Server using one of the
methods presented in Setting the IP Address, on page 16.
After you have completed the procedures in the AS/400 Host system
checklist above, follow the instructions below to configure the Axis
Network Print Server for SNA printing in the AS/400 environment using
a Web browser:
1. Start a Web browser, e.g. Internet Explorer or Netscape Navigator.
2. Enter the IP address or the host name of the Axis Network Print Server in
the location field and press the Enter key on your keyboard. The internal Web
pages of the Axis Network Print Server will appear.
Note:
To protect the Admin pages and the Configuration Wizard from unauthorized use, enter a
password (default Pass) in the Root Password field under
Admin | General Settings.
3. Click the Configuration Wizard for IBM sessions button.
4. Click the Add Session button. This will start the Configuration Wizard
which is a step-by-step guide through the required IBM configuration
settings.
Notes for SCS printing:
•
In the Configuration Wizard’s IBM Printer Emulation window, 38xx is the value used for
LaserWriter printers and all other values are used for matrix printers.
•
In the Configuration Wizard Printer Driver window, PCL is used for LaserWriter printers, all
other values apply to matrix printers.
Note for IPDS printing:
In the Configuration Wizard, you can choose between PCL or PostScript printing. Choose the
printer language that corresponds to your printer.
28
AXIS 5570e / AXIS 5670e User’s Manual
Setting Up - AS/400 (iSeries)
Verifying the
Communication Link
1. Type WRKCFGSTS *CTL xxxx* on the AS/400 command line (xxxx is the
first four characters of the Axis Network Print Server 5494 LU
Name)and press Enter. After a couple of minutes, ensure that the
following items are displayed:
•
One APPC controller with the same name as the Axis Network Print
Server 5494 LU Name.
•
One APPC device with the same name as the Axis Network Print
Server 5494 LU Name, one controller session (QRMTWSC) and the
currently active printer sessions (QRMTWSC).
•
One twinax controller named xxxxxRMT, where xxxxx are the first
five characters of the Axis Network Print Server 5494 LU Name.
•
One, two or three twinax printer devices named xxxxPRT0z (xxxx
are the first four characters of the Axis Network Print Server 5494
LU Name and z is the printer device number).
The status of all items should now be ACTIVE or VARIED ON.
2. Type STRPRTWTR xxxxPRT0z on the AS/400 command line (xxxxPRT0z is
the printer device name) and press Enter. This command starts the writer
for this printer device.
3. Press the Axis Network Print Server test button once to print a test page.
Ensure that the SNA status is defined on the test page as Idle, Actv or
LU-4.
TN5250E Printing (SCS over IP)
TN5250E is the recommended protocol to use when printing SCS data
streams over TCP/IP. This print method offers superior control,
management and throughput for the Axis Network Print Server.
Before you Begin
Make sure that the AS/400 host is running OS/400 V3R2 or higher with
TCP/IP support installed and configured.
Make sure that the latest PTFs are installed. Information about which
PTFs to use can be obtained from:
http://as400service.rochester.ibm.com/
The AS/400 Host
System Checklist
There is an AS/400 Parameter checklist in the AXIS 5570e/AXIS 5670e Axis Network Print
Server User’s Guide where you can enter the values described in this section for future
reference.
AXIS 5570e / AXIS 5670e User’s Manual
29
Setting Up - AS/400 (iSeries)
1. Type WRKCTLD *VWS on the AS/400 command line and press Enter to
determine the number of auto-configured virtual devices on your AS/400
system. Press F3.
2. Type DSPSYSVAL QAUTOVRT and press Enter. Make sure that the value of
the QAUTOVRT parameter is greater than the number of auto-configured
virtual devices. Press F3.
3. Type DSPSYSVAL QCHRID and press Enter. Note the system language (code
page) for future reference. Press F3.
4. Type WRKTCPSTS OPTION *IFC and press Enter to determine the IP address
of the AS/400 server. Press F3.
Configuring the
Axis Network Print
Server
Follow the instructions below to configure the Axis Network Print Server
for TN5250E printing using a Web browser:
1. Start a Web browser, e.g. Internet Explorer or Netscape Navigator.
2. Enter the IP address or the host name of the Axis Network Print Server in
the location field and press the Enter key on your keyboard. The internal Web
pages of the Axis Network Print Server will appear.
Important:
To protect the admin pages and the Configuration Wizard from unauthorized use, enter a
password (default Pass) in the Root Password field under Admin | General Settings.
3. Click the Configuration Wizard for IBM sessions button.
4. Click the Add Session button. This takes you to the Configuration Wizard
which is a step-by-step guide through the required configuration settings.
Notes:
Verifying the
Communication Link
•
In the Configuration Wizard, you must choose a new and unused name for the printer (in
the ‘Printer Name’ field) when in the ‘TN5250E Protocol Configuration’ window.
•
In the Configuration Wizard’s ‘Printer Driver’ window, PCL is used for LaserWriter printers,
all other values apply to matrix printers.
1. Type WRKCFGSTS *DEV xxxx*, where xxxx are the first four characters of
the printer device name, on the AS/400 command line and press Enter. A
list of printer devices will be displayed. Make sure that a virtual printer
device is active.
2. Direct a printout to this printer device to check the integrity of the
communication link.
3. Press the test button on the Axis Network Print Server once to print a test
page. Make sure that the TN5250E status is defined on the test page as
Idle, Actv or LU-1.
30
AXIS 5570e / AXIS 5670e User’s Manual
Setting Up - AS/400 (iSeries)
PPR/PPD Printing - IPDS Data Streams
Note:
IPDS is only available for AXIS 5570e/AXIS 5670e models with the IPDS option installed. For
more information, refer to Protocols and Datastreams, on page 9.
The configuration procedures presented in this section are divided into
three separate steps:
•
•
•
Before you Begin
Configuring the AS/400 host
Configuring the AXIS 5570e/AXIS 5670e
Verifying the communication between the AXIS 5570e/AXIS 5670e and
the AS/400
Make sure that the AS/400 host is running OS/400 V3R6 or higher with
TCP/IP support installed and configured.
Make sure that the latest PTFs are installed. Information about which
PTFs to use can be obtained from:
http://as400service.rochester.ibm.com/
Configuring the
AS/400 Host System
Creating a PSF
Configuration
When configuring the AS/400 host system you can:
•
•
create a PSF configuration
create a printer device description
The system uses default values but you can optionally create a PSF
configuration by following the instructions below:
1. Issue the command CRTPSFCFG.
2. Press F11 to display keywords.
3. Select a name for the PSF configuration and enter it at the PSF
configuration (PSFCFG) line. The name may comprise the letters A-Z and
the numerals 0-9, but must begin with a letter. A maximum of 10 characters
are allowed.
4. Enter QGPL at the Library line.
5. Enter *YES at the IPDS pass through (IPDSPASTHR) line.
6. Enter *NORDYF at the Activate release timer (ACTRLSTMR) line.
7. Enter *NOMAX at the Release timer (RLSTMR) line.
8. Press the Enter key on your keyboard to create the PSF configuration.
Many of the settings presented in the following panel example can be left
at their default settings. However, the settings that you must change are
highlighted in bold text and the settings that you must enter exactly as
shown in the example are highlighted in bold underlined text.
AXIS 5570e / AXIS 5670e User’s Manual
31
Setting Up - AS/400 (iSeries)
Example:
Create PSF Configuration (CRTPSFCFG)
Type choices, press Enter.
PSF configuration. . . . . . . . PSFCFG
Library
. . . . . . . . . . .
> AXISPR1
> QGPL
User resource library list . . . USRRSCLIBL
*JOBLIBL
Device resource library list . . DEVRSCLIBL
*DFT
+ for more values
IPDS pass through. . . . . . . . IPDSPASTHR
> *YES
Activate release timer . . . . . ACTRLSTMR
> *NORDYF
Release timer. . . . . . . . . . RLSTMR
> *NOMAX
Restart timer. . . . . . . . . . RESTRTMR
*IMMED
APPC and TCP/IP retry count. . . RETRY
15
Delay between APPC retries . . . RETRYDLY
90
Automatic session recovery . . . UAUTOSSNRCY
*NO
Acknowledgment frequency . . . . ACKFRQ
100
Text ‘description’ . . . . . . . TEXT
*BLANK
Bottom
Creating a Printer
Device Description
Create a printer device description by following the instructions below:
1. Issue the command CRTDEVPRT and press Enter.
2. Press F11 to display keywords.
3. Select a name for the printer device and enter it at the Device Description
(DEVD) line. The name may comprise the letters A-Z and the numerals 09, but must begin with a letter. A maximum of 10 characters are allowed.
In the following instructions the printer device name will be referred to as
AXISPR1.
4. Enter *LAN at the Device class (DEVCLS) line.
5. Enter *IPDS at the Device type (TYPE) line.
6. Enter 0 at the Device model (MODEL) line.
7. Enter *IP at the LAN attachment (LANATTACH) line.
8. Enter a port number at the Port number (PORT) line. The Axis print server
is pre-configured with the port numbers 5001, 5002 and 5003 for IPDS
printing.
9. Enter a FGID number at the Font Identifier (FONT) line, e.g. 11 (Courier).
10. Define the Remote location (RMTLOCNAME). Use the IP address of the AXIS
5470e/670e.
11. (Optional) Enter the name of the previously created PSF configuration at the
User-defined object (USRDFNOBJ): Object line.
12. (Optional) Enter the library of the previously created PSF configuration at
the User-defined object (USRDFNOBJ): Library line.
13. (Optional) Enter *PSFCFG at the User-defined object (USRDFNOBJ):
Object type line.
32
AXIS 5570e / AXIS 5670e User’s Manual
Setting Up - AS/400 (iSeries)
14. Press the Enter key on your keyboard to create the printer device
description.
Many of the settings presented in the following panel example can be left
at their default settings. However, the settings that you must change are
highlighted in bold text and the settings that you must enter exactly as
shown in the example are highlighted in bold underlined text.
Create Device Desc (Printer) (CRTDEVPRT)
Type choices, press Enter.
Device description . . . . . . . DEVD
> AXISPR1
Device class . . . . . . . . . . DEVCLS
> *LAN
Device type
> *IPDS
. . . . . . . . . . TYPE
Device model . . . . . . . . . . MODEL
> 0
LAN attachment . . . . . . . . . LANATTACH
> *IP
Advanced function printing . . . AFP
Port number
. . . . . . . . . . PORT
Online at IPL
. . . . . . . . . ONLINE
Font:
*YES
> 5001
*YES
FONT
Identifier . . . . . . . . . .
Point size . . . . . . . . . .
Form feed. . . . . . . . . . . . FORMFEED
> 11
*NONE
*FILE
Separator drawer . . . . . . . . SEPDRAWER
*FILE
Separator program
*NONE
Library
. . . . . . . SEPPGM
. . . . . . . . . . .
Printer error message
. . . . . PRTERRMSG
*INQ
More...
Message queue
Library
. . . . . . . . . MSGQ
. . . . . . . . . . .
Activation timer . . . . . . . . ACTTMR
QSYSOPR
*LIBL
170
Image configuration. . . . . . . IMGCFG
*NONE
Maximum pending requests . . . . MAXPNDRQS
6
Print while converting . . . . . PRTCVT
*YES
Print request timer. . . . . . . PRTRQSTMR
*NOMAX
Form definition. . . . . . . . . FORMDF
F1C10110
Library. . . . . . . . . . . .
*LIBL
Remote location: . . . . . . . . RMTLOCNAME
Name or address. . . . . . . .
User-defined options . . . . . . USRDFNOPT
> ‘192.168.5.23’
*NONE
+ for more values
More...
AXIS 5570e / AXIS 5670e User’s Manual
33
Setting Up - AS/400 (iSeries)
User-defined objects . . . . . . USRDFNOBJ
Object . . . . . . . . . . . .
> AXISPR1
Library . . . . . . . . . .
> QGPL
Object type. . . . . . . . . .
> *PSFCFG
Data transform program . . . . . USRDTATFM
*NONE
Library. . . . . . . . . . . .
User-defined driver program. . . USRDRVPGM
*NONE
Library. . . . . . . . . . . .
Text ‘description’ . . . . . . . TEXT
IPDS over PPR/PPD
More...
Configuring the Print
Server
Follow the instructions below to configure your AXIS 5570e/AXIS 5670e
using a standard Web browser:
1. Start a Web browser, e.g. Internet Explorer or Netscape Navigator.
2. Enter the IP address or the host name of the AXIS 5570e/AXIS 5670e in the
location field and press the Enter key on your keyboard. The internal Web
pages of the AXIS 5570e/AXIS 5670e will appear.
Note:
To protect the Admin pages and the Configuration Wizard from unauthorized use, enter a
password (default Pass) in the Root Password field under Admin | General Settings.
Note for IPDS printing:
In the Configuration Wizard, you can choose between PCL or PostScript printing. Choose the
printer language that corresponds to your printer.
3. Click the Configuration Wizard for IBM sessions button.
4. Click the Add Session button. This takes you to the Configuration Wizard
which is a step-by-step guide through the required configuration settings.
Verifying the
communication
Follow the instructions below to verify the communication by sending a
print job to the AXIS 5570e/AXIS 5670e:
AXISPR1 is an example. Refer to Creating a Printer Device Description, on page 32 for
details.
1. Type WRKCFGSTS *DEV AXISPR1 on the AS/400 command line and press
Enter to display the previously created printer device. The status of the
printer device should be VARIED OFF.
2. Vary on the printer device by typing 1 in the Opt field. Press ENTER.
3. Press F5 to refresh the display. The printer device should now be VARIED ON.
4. Start the printer writer by typing STRPRTWTR AXISPR1 on the AS/400
command line. Press Enter.
5. Press F5 to refresh the display. The printer device should now be
ACTIVE/WRITER.
34
AXIS 5570e / AXIS 5670e User’s Manual
Setting Up - AS/400 (iSeries)
6. Direct a printout to this printer device. A successful printout verifies the
communication link between the AS/400 and the AXIS 5570e/AXIS 5670e.
The AXIS 5570e/AXIS 5670e is now ready for printing in the AS/400
environment.
AXIS 5570e / AXIS 5670e User’s Manual
35
Setting Up - IBM Mainframe (zSeries)
Section 5
Setting Up - IBM Mainframe (zSeries)
This section describes how to configure the Axis Network Print Server for
printing SCS, 3270 and IPDS data streams using SNA and TCP/IP
transport protocols in the IBM Mainframe (zSeries) environment.
Proceed to the setup section that is relevant to your network
environment, as described in the table below:
Printing protocol
Data streams
Action
SCS
SNA
3270DS
SNA Printing, on page 36
IPDS
SCS
TN3270E (TCP/IP)
3270DS
TCP/IP TN3270E Printing, on page 42
IPDS
PPR/PPD (TCP/IP)
IPDS
PPR/PPD Printing - IPDS data streams, on page 50
Notes:
•
IPDS is only available for print server models with the IPDS option installed.
•
SNA is only available for print server models with the SNA option installed.
Please refer to “Protocols and Datastreams” on page 9.
If you intend to operate your Axis Network Print Server in a multiprotocol environment, you should also proceed to the other relevant
sections in this manual.
SNA Printing
The Axis Network Print Server supports printing of SCS, 3270 and IPDS
data streams via the SNA transport protocol.
Important:
The Axis Network Print Server must be set up to emulate an IBM 3174 (3174 CU mode) in the
Mainframe/VTAM environment.
Configuring for SNA printing in 3174 CU Mode is described in three
separate stages:
•
•
•
36
Configuring the IBM Mainframe Host system
Configuring the Axis Network Print Server
Verifying the communication
AXIS 5570e / AXIS 5670e User’s Manual
Setting Up - IBM Mainframe (zSeries)
Configuring the
Mainframe
Host System
These procedures are compulsory for printing in the IBM Mainframe
environment.
Configuring the host system requires you to do the following:
•
•
Before you Begin
Make sure that a VTAM Logon-mode entry is available for your Axis
Network Print Server.
Create the VTAM Definition for the Major Node where the Print Server
definition is to be placed.
Make note of the Axis Network Print Server serial number that is found
on the underside label of the print server.
Important:
When using a concentrator gateway between the host and your print server, it is not necessary
to define separate VTAM Major Node and PU definitions for the Axis Network Print Server. You
will instead be working with the gateway VTAM definitions. Since the Axis Network Print
Server will appear to the host as one or several LU's attached to the gateway PU, you need only
add LU definitions to the gateway major node definition and then proceed to item 3 below.
1. Define a VTAM Major Node Definition where the Print Server
definitions will be placed. Using a channel attached 3174 as a gateway to
the host, this definition is typically defined as a Local Major Node.
If you are using a remotely attached gateway via a 37X5 communications
controller or a LAN attached 3172, you will be working with a
Switched Major Node definition.
2. Add the Print Server PU and LU definitions to the major node definition.
For Switched Major Node definitions you need to:
•
Add the IDBLK (default = E07) and IDNUM (default = last 5 digits of the Axis
Network Print Server MAC address) entries to the PU definition.
•
Code a PATH definition using the unit’s full 12 digit MAC address.
Example: An Axis Network Print Server with a MAC/node address of
00408C100086 will be defined as:
PA5570e1
PATH
DIALNO=010400408C100086, GID=1, FID=1,
GRPNM=gggggg
Note:
‘GRPNM’ specifies the symbolic name of a GROUP statement in an NCP major node. That
GROUP statement defines a logical group of SDLC switched lines or token-ring switched lines.
3. Make sure that the corresponding VTAM Logon-mode entries are
available and that the appropriate LU session types (LU1 or LU3) are used.
4. Vary ACTive the VTAM Major Node definition for the Axis Network
Print Server.
AXIS 5570e / AXIS 5670e User’s Manual
37
Setting Up - IBM Mainframe (zSeries)
Sample Sessions
Logon-mode Entry
The examples below are based on samples given in VTAM
Customization (IBM part no: SC23-0112), with some changes to
optimize use for Axis Network Print Server. VTAM for MVS is assumed,
although the configuration for VM and VSE is similar.
Creating a VTAM Logon-mode entry for your Axis Network Print Server.
Logon-mode entry for LU type 1 printing:
*
* For application output of LU-1 SNA Character Stream (SCS)
*
TITLE SCS5570e
SCS5570e
MODEENT LOGMODE=SCS5570e,
X
FMPROF=X03,
X
TSPROF=X03,
X
PRIPROT=XB1,
X
SECPROT=XB0,
X
COMPROT=X3080,
X
RUSIZES=X8585,
X
PSERVIC=X014000010000000001000000,
X
PSNDPAC=X03,
X
SRCVPAC=X03
Logon-mode entry for LU type 3 printing:
*
* For application output of LU-3 3270 Data Stream (3270DS)
*
TITLE ‘DSC5570e’
DSC5570e
MODEENT LOGMODE=DSC5570e,
X
FMPROF=X’03’,
X
TSPROF=X’03’,
X
PRIPROT=X’B1’,
X
SECPROT=X’90’,
X
COMPROT=X’3080’,
X
RUSIZES=X’8585’,
X
PSERVIC=X’030000000000185018507F00’, X
PSNDPAC=X’03’,
X
SRCVPAC=X’03’
38
AXIS 5570e / AXIS 5670e User’s Manual
Setting Up - IBM Mainframe (zSeries)
Switched Major
Node Definitions
The example below shows how the print server PU, PATH, and LU
definitions may be coded in a switched major node definition.
* PU definition
* E07xxxxxx is the node ID set in Axis Network Print Server.
*
PU5570e1
PUADDR=04,
X
PUTYPE=2,
X
IDBLK=E07,
X
IDNUM=nnnnn,
X
MAXPATH=1,
X
SSCPFM=USSSCS,
X
USSTAB=USSMAST,
X
VPACING=(0)
*
* Path definition
* xxxxxxxxxxxx is the 12 last digits of the MAC
* address of the Axis Network Print Server
*
PA5570e1
PATHDIALNO=0104xxxxxxxxxxxx,
X
GID=1,
X
PID=1,
X
GRPNM=gggggg
*
* LU definitions. Use either LU5570e1 or LU5570e3
*
* LU type 1 (SCS)
*
LU5570e1
LULOCADDR=2,
X
DLOGMOD=SCS5570e,
X
VPACING=7,
X
PACING=3
*
* LU type 3 (3270DS)
*
LU5570e3
LULOCADDR=2,
X
DLOGMOD=DSC5570e,
X
VPACING=7,
X
PACING=3
AXIS 5570e / AXIS 5670e User’s Manual
39
Setting Up - IBM Mainframe (zSeries)
Note:
In the PU definition, IDNUM should be set to the five last digits of the Axis Network Print
Server node address, NODE_ADDR. By default NODE_ADDR stands for the five last digits of
the Axis Network Print Server serial number.
In the path definition, PATH DIALNO should be comprised with its first two digits equal to
the place holder, the next two set to the SAP and the remaining twelve digits set to the Axis
Network Print Server Ethernet or Node address. By default the Ethernet/Node address is
identical to the Axis Network Print Server serial number. A valid GRPNM must also be
supplied.
In the LU definition, the LOCADDR number maps to the Logical Printer number of the Axis
Network Print Server. The first eight Local Addresses pass the printout through Logical Printer
1-8. However, some IBM systems do not allow Local Address 1 to be used for printing. Refer
to “Logical Printers for Customized Printing” on page 154 for more information about
logical printers.
Node Definitions
The example below shows how the print server PU and LU definitions
may be coded in a local major node definition:
* 5570e DSPU DEFINITION
DSPU5570e5570ePU CUADDR=E31,
X
MODETAB=MODE3290,
X
PUTYPE=2,ISTATUS=ACTIVE,MAXBFRU=1
DSPULU02 LU
LOCADDR=2
X
SSCPFM=USSSCS,
X
USSTAB=USSTAB,
X
PACING=1,
X
VPACING=2,
X
ISTATUS=ACTIVE,
X
LOGAPPL=MWTC,
X
DLOGMOD=SCS5570e
DSPULU03 LU
LOCADDR=3,
X
SSCPFM=USSSCS,
X
USSTAB=USSTAB,
X
PACING=1,
X
VPACING=2,
X
ISTATUS=ACTIVE,
X
LOGAPPL=MWTC,
X
DLOGMOD=SCS5570e
40
AXIS 5570e / AXIS 5670e User’s Manual
Setting Up - IBM Mainframe (zSeries)
Note:
If the LAN media at the remote (Print Server) location differs from that at the host location
(e.g. Remote LAN = Ethernet and Host LAN = Token Ring), the MAC address definitions must
be modified, as outlined below:
Print Server Modifications:
The Axis Network Print Server Host MAC address (H1_MAC_ADDR) must be bit-order reversed
for each byte,
e.g. if the host address is 08005AB77D49 the converted address will be 10005AEDBE92
Host Modifications:
The required Host modifications are dependent upon the VTAM definition for the Major Node
where the Print Server definition is placed.
Case 1:
VTAM Major Node definition is a Switched Major Node.
The MAC address of the Axis Network Print Server must be bit-order reversed in the PATH
entry. An Axis Network Print Server with a MAC/node address of 00408C1B06D4 will be
defined using the MAC/node address 000231D8602B as follows:
Case 2:
VTAM Major Node definition is a Local Major Node.
When using a channel attached controller as gateway to the host, the MAC address of the
Axis Network Print Server is configured in the gateway. The address must be reversed, as in
case 1 above.
Configuring the
Axis Network Print
Server
To perform the instructions presented in this section, you should first
assign an IP address to your Axis Network Print Server using one of the
methods presented in Setting the IP Address, on page 16.
The purpose of the configuration of the Axis Network Print Server is to
emulate a LAN attached IBM 3174 Control Unit running SNA PU2.0.
Follow the instructions below to configure the Axis Network Print Server
using a Web browser:
1. Start a Web browser, e.g. Internet Explorer or Netscape Navigator.
2. Enter the IP address or the host name of the Axis Network Print Server in
the location field and press the Enter key on your keyboard. The internal Web
pages of the Axis Network Print Server will appear.
Important:
To protect the Admin pages and the Configuration Wizard from unauthorized use, enter a
password (default Pass) in the Root Password field under Admin | General Settings.
3. Click the Configuration Wizard for IBM sessions button.
4. Click the Add Session button. This will start the Configuration Wizard
which is a step-by-step guide through the required configuration settings.
Notes for SCS printing:
•
In the Configuration Wizard’s IBM Printer Emulation window, 38xx is the value used for
LaserWriter printers and all other values are used for matrix printers.
•
In the Configuration Wizard Printer Driver window, PCL is used for LaserWriter printers, all
other values apply to matrix printers.
AXIS 5570e / AXIS 5670e User’s Manual
41
Setting Up - IBM Mainframe (zSeries)
Note for IPDS printing:
In the Configuration Wizard, you can choose between PCL or PostScript printing. Choose the
printer language that corresponds to your printer.
Verifying the
Communication Link
Procedures
The easiest way to test the communication is by sending a print job to the
Axis Network Print Server. If there are problems, press the test button
once to print the test page where you can find the present SNA link
status.
1. Power on the Print Server and wait for 2 minutes.
2. Press the test button once to print a test page and make sure that the SNA
status line is defined as either:
•
Idle
•
Actv
•
LU-1
•
LU-3
Note:
Please refer to the Parameter List and FAQ on the Axis Web site, if the status line indicates
that the SNA link is not active.
The Axis Network Print Server is now ready for use in the SNA
environment.
TCP/IP TN3270E Printing
The following procedures describe how to configure the Axis Network
Print Server for SCS, 3270DS and IPDS printing, using TCP/IP TN3270E.
This is achieved by establishing communication between the Axis
Network Print Server and Mainframe host via a TN3270E server, using the
TCP/IP transport protocol for the SCS, 3270 and IPDS data streams, as
illustrated below:
AXIS Print server
IPDS is only available for print server models with the IPDS option installed. Please refer to
“Protocols and Datastreams” on page 9
42
AXIS 5570e / AXIS 5670e User’s Manual
Setting Up - IBM Mainframe (zSeries)
Configuring for TN3270E printing is described in four separate stages:
•
•
•
•
Configuring the
Mainframe Host
Configuring the
Axis Network Print
Server
Configuring the IBM Mainframe Host system
Configuring the Axis Network Print Server
Configuring the TN3270E server
Verifying the communication
Consult your TN3270E server documentation and make sure that the
appropriate VTAM host system definitions are set up for
mainframe-to-TN3270E server SNA communication.
Follow instructions below to configure the Axis Network Print Server
using a Web browser:
1. Start a Web browser, e.g. Internet Explorer or Netscape Navigator.
2. Enter the IP address or the host name of the Axis Network Print Server in
the location field and press the Enter key on your keyboard. The internal Web
pages of the Axis Network Print Server will appear.
Important:
To protect the Admin pages and the Configuration Wizard from unauthorized use, enter a
password (default Pass) in the Root Password field under Admin | General Settings.
3. Click the Configuration Wizard for IBM sessions button.
4. Click the Add Session button. This will start the Configuration Wizard
which is a step-by-step guide through the required configuration settings.
Notes for SCS printing:
•
In the Configuration Wizard, Non-IPDS Printer Emulation uses value structure 38xx for
LaserWriter printers. All other values can be used for matrix printers.
•
In the Configuration Wizard’s Printer Driver window, PCL is used for LaserWriter printers, all
other values apply to matrix printers.
Note for IPDS printing:
•
The AXIS 5570e/AXIS 5670e supports eight concurrent TN3270E host sessions.
•
In the Configuration Wizard, you can choose between PCL or PostScript printing. Choose the
printer language that corresponds to your printer.
AXIS 5570e / AXIS 5670e User’s Manual
43
Setting Up - IBM Mainframe (zSeries)
Configuring the
TN3270E server
The TN3270E server may be implemented as a software package running
on the mainframe itself, a router or other server hardware.
Configuration examples for two popular TN3270E-capable servers are
described below, namely:
•
•
Microsoft SNA Server
Novell NetWare for SAA.
AXIS Print server
Typical Axis Network Print Server TCP/IP TN3270E Network Configuration
Note:
Microsoft SNA Server
•
Configuration procedures can differ from other TN3270E servers.
•
For additional information about configuring other TN3270E servers, refer to the Support
pages on www.axis.com
Communication is established in two separate stages, SNA Server-to-Host
connection and SNA Server to Axis Network Print Server connection, as
described below:
SNA Server-to-Host Connection
Follow the steps below to set-up a SNA Server-to-Host connection for the
Axis Network Print Server:
1. Start Microsoft SNA Server Manager and click the Servers folder. The
Main SNA Server Manager Window is featured in the illustration below.
2. Insert a new Connection to the host under Connections. Refer to the online
help for assistance on how to configure the connection.
3. Select the new connection and Insert a 3270 Application LU (LUA) to this
connection.
4. Set the LU Number to the LU Number specified in the host.
5. Set the LU Name to the name you want to use for the printer device. This
is the same name that you specify in the TN3270E Printer Name parameter
of the Axis Network Print Server.
44
AXIS 5570e / AXIS 5670e User’s Manual
Setting Up - IBM Mainframe (zSeries)
6. Click OK.
SNA Server Manager Main Window
SNA Server - Axis Network Print Server connection
1. Select the new LUA and drag it to the TN3270 connection definition
(highlighted in the SNA Server Manager Window above).
2. Select the properties of the LUA.
3. Click the TN3270 tab in the properties popup window.
4. Select Generic Printer Type.
5. Click the IP Address List tab.
6. Specify the IP Address of the client(s) that you want to assign to this LU. This
is the IP address of the Axis Network Print Server, i.e. the same as the
INT_ADDR parameter in the Print Server.
7. Click OK.
Verifying the
Communication:
1. Activate the connection you created in step 2 of the above SNA Server Axis Network Print Server connection procedures. The status of the
connection should be “active”.
2. Make sure the corresponding LU in the host is activated.
3. Activate the TN3270 connection to the Axis Network Print Server. The LUA
should change status to SSCP.
4. Check that the printer is connected to the Axis Network Print Server.
5. Send a print job from the host.
The Axis Network Print Server is now ready for use.
AXIS 5570e / AXIS 5670e User’s Manual
45
Setting Up - IBM Mainframe (zSeries)
Notes:
NetWare for
SAA Server
•
You can check the status of the TN3270E connection by printing a test page from the Print
Server. This is done by pressing the test button once. Make sure the TN3270E status (St:) line
for your server connection is defined as either:
•
SSCP
•
LU-1
•
LU-3
•
For additional information about configuring other TN3270E servers, refer to the Technical
Notes on www.axis.com
To set-up a TN3270E connection to the Axis Network Print Server you
have to set up PU and LU definitions. This is done by following the steps
below:
1. Start the NWSAA Administrator.
2. Double-click the NWSAA Node. The panel below will appear.
3. Enter the Node ID for the host.
4. Leave the rest at their default settings.
Peer PU profile
5. Click the TN3270 icon. The panel below will appear.
6. Select All Available Host PU profiles.
7. Enter the user name, from the User List, that you want all TN3270 clients
to use.
8. Specify the maximum number of TELNET connections you want to allow
each TN3270 client.
46
AXIS 5570e / AXIS 5670e User’s Manual
Setting Up - IBM Mainframe (zSeries)
9. Leave the rest at their default settings and click OK.
PU profile name and Logical adapter
10. Press the “insert” key to create a new Host PU Profile. Choose Host PU Profile
from the list displayed in the dialog. Then the panel below will appear.
Printer LU
11. Enter a unique name as PU profile name.
12. Enter the number of dependent LUs you want for this PU.
13. Enter the starting LU number.
14. Enter the Node ID (the same ID as for item 3 above).
15. Choose logical adapter.
16. Set maximum frame size to transmit inbound to match the MAXDATA in
the host definition.
17. Enter the host node address.
18. Leave the rest at their default settings.
19. Click the LU Defaults icon. The panel below will appear
20. Set Default LU category to Public.
AXIS 5570e / AXIS 5670e User’s Manual
47
Setting Up - IBM Mainframe (zSeries)
21. Set Default LU type to Printer (LU type 1 or 3).
22. Specify the VTAM LU name prefix. Click OK.
Notes:
•
When the LUs are created the default names for the Printer Devices will be <name prefix>
followed by a two digit number starting at the number you entered in the starting dependent LU number field.
•
In the example below, eight LUs are created automatically. The LU names created will be
BRLTST04 through to BRLTST0B. These names must correspond to the Printer Names you
specify for the TN3270E sessions in the Print Server.
You can now generate a configuration report from NW for SAA. To do
this, simply mark the server icon in the left window and select
Generate Server Configuration Report from the function
menu.
The following table is a summary of a report generated by this command
for the example above.
Profile Name
NWSAA
SNA Network ID:
SEEDB
Peripheral node control point name:
CPNAME
Block ID/PU ID:
05D 66204
Local/Partner SAP for ILUs:
04
Logical Adapter:
E100B_1
PU Profile:
NWSAAPU
Adapter Name
E100B_1
Adapter Type:
LLC 802.2
Terminate peer link if no active APPC sessions:
No
Logical adapter number:
0
Number of local service access points:
2
Enable adapter at startup:
Yes
PU Profile Name
NWSAAPU
Number of dependent LUs:
8
Starting dependent LU number:
Peripheral node control point name:
4
NWSAAPU
Node ID (block/PU ID):
05D 66204
Offline test mode:
No
Assign only LUs activated by the host:
Yes
Enable SDDLU Support:
No
Adapter Name:
E100B_1
Adapter Type:
LLC 802.2
Maximum Session Count:
9
VTAM Name Prefix:
BRLTST
Default LU Type:
1
Default Model Number:
2
Default LU Category:
Public
Maximum frame size to transmit inbound:
0521
Remote node address:
020066800000
Remote Service Access Point:
48
04
Local Service Access Point:
04
Enable PU profile at startup:
Yes
AXIS 5570e / AXIS 5670e User’s Manual
Setting Up - IBM Mainframe (zSeries)
LU id
Category
VTAM LU Name
Type
0
Public
4
Mod
14
2
TSELF
Public
BRLTST04
1
2
TSELF
5
Public
BRLTST05
1
2
TSELF
6
Public
BRLTST06
1
2
TSELF
7
Public
BRLTST07
1
2
TSELF
8
Public
BRLTST08
1
2
TSELF
9
Public
BRLTST09
1
2
TSELF
10
Public
BRLTST0A
1
2
TSELF
11
Public
BRLTST0B
1
2
TSELF
PU Profile Names
NetWare SAA
Maximum connections per client
5
Use IP client name
No
TN3270 NetWare User ID
Admin
Client Response Timer
120
Printer End of Job Timer
9999
Termination
Method
Summary of a report generated by Generate Server
Configuration Report (bold text = not default).
Verifying the
Communication:
Follow the steps below to test the communication by sending a print job
to the Axis Network Print Server.
1. Make sure the printer is connected to the Axis Network Print Server and
the corresponding LU in the host is activated.
2. Send a print job from the host.
The Axis Network Print Server is now ready for use. If needed, it can be
further adapted to your system using the Web-based configuration pages
or IBM Printer Emulation. Please refer to Extended IBM Printer
Emulation, on page 179.
You can check the status of the TN3270E connection by printing a test page from the Print
Server. This is done by pressing the test button once. Make sure the TN3270E status (St:) line
for your server connection is defined as either:
•
SSCP
•
LU-1
•
LU-3
For additional information about configuring other TN3270E servers, refer to the Technical
Notes on www.axis.com
AXIS 5570e / AXIS 5670e User’s Manual
49
Setting Up - IBM Mainframe (zSeries)
PPR/PPD Printing - IPDS data streams
Important:
IPDS is only available for print server models with the IPDS option installed. Please refer to
“Protocols and Datastreams” on page 9.
Before you Begin
In order to use the Axis Network Print Server to print IPDS data using
TCP/IP as the transport protocol, the following software must be installed
and configured on your MVS:
•
•
•
Configuration
Procedures
PSF/MVS Version 2 release 2.0 with APAR OW15599.
MVS Scheduler APAR OW12236 to support the two new PRINTDEV
keywords: IPADDR and PORTNO.
TCP/IP version 3 release 1, or higher
The configuration procedures presented in this section are divided into
seven separate steps:
1. Specifying the TCP/IP address space name
2. Defining the MVS control unit
3. Modifying the TCP/IP profile on your MVS system, if necessary
4. Configuring the Axis Network Print Server
5. Verifying the communication between the Axis Network Print Server and
the IBM Mainframe
6. Defining the Axis Network Print Server as a writer-controlled printer to JES
7. Defining the printer to PSF with a PRINTDEV statement, including the IP
address and port number.
Specifying the TCP/IP
Address Space Name
To specify a TCP/IP address space name you should enter the following
EXEC statement in the appropriate PSF writer procedure:
//STEP01 EXEC PGM=APSPPIEP,REGION=4096K,PARM=(,,,,tcpip_name)
where tcpip_name is the name of the TCP/IP address space. If this
parameter is not coded, PSF uses the default name TCPIP. For a full
description of the PARM parameter refer to IBM’s user documentation
covering the print service facility.
Defining the
MVS Control Unit
If you have not already done so, you must define the communications
control unit, e.g. the 3172 control unit or the 3745 control unit, to MVS.
The tool to use is dependent on your MVS version:
•
•
50
When using a version earlier than MVS 4.1.0, you should use an MVS
Configuration Program (MVSCP).
When using a version of MVS 4.1.0 or higher, you can use a HardWare
Configuration Definition (HCD) or an MVSCP.
AXIS 5570e / AXIS 5670e User’s Manual
Setting Up - IBM Mainframe (zSeries)
For more information about using these methods, please refer to one of
the following publications:
•
•
•
Modifying the
TCP/IP Profile
MVS/ESA Planning: Dynamic I/O Configuration
OS/390 HCD Planning
HCD User's Guide
The TCP/IP profile contains system configuration statements used to
initialize the TCP/IP address space. Among those statements, the
following are subject to special considerations when you are printing
from PSF on TCP/IP-attached printers:
• DATABUFFERPOOLSIZE
• SMALLDATABUFFERPOOLSIZE
• TINYDATABUFFERPOOLSIZE
• KEEPALIVEOPTIONS
• GATEWAY
Below is an excerpt from an example TCP/IP Profile (not a complete
profile) . Examples of the statements above are printed in bold:
ACBPOOLSIZE
1000
ADDRESSTRANSLATIONPOOLSIZE
1500
CCBPOOLSIZE
150
DATABUFFERPOOLSIZE
160
32768
ENVELOPEPOOLSIZE
750
IPROUTEPOOLSIZE
300
LARGEENVELOPEPOOLSIZE
50
RCBPOOLSIZE
50
SCBPOOLSIZE
256
SKCBPOOLSIZE
256
SMALLDATABUFFERPOOLSIZE
256
TCBPOOLSIZE
512
TINYDATABUFFERPOOLSIZE
UCBPOOLSIZE
256
100
KEEPALIVEOPTIONS
INTERVAL
10 SENDGARBAGE
FALSE
ENDKEEPALIVEOPTIONS
GATEWAY
; * Network
10
First Hop
=
Linkname
BCPLAN
DEFAULTNET 10.10.12.1 BPCLAN
Packet Size Subnet mask
2000
2000
Subnet value
255.255.255.0 10.10.12.0
255.255.255.0 0
Note:
If you change any of the values in the TCP/IP profile, you must restart TCP/IP to activate the
new settings.
AXIS 5570e / AXIS 5670e User’s Manual
51
Setting Up - IBM Mainframe (zSeries)
The table below provides more information about the statements.
Statement
Explanation
DATABUFFERPOOLSIZE
Defines the number and size of the data buffers. It is recommended
that you specify at least 160 data buffers and a buffer size of
32768 bytes
SMALLDATABUFFERPOOLSIZE
Defines the number of small data buffers. It is recommended that
you specify at least 256 small data buffers
TINYDATABUFFERPOOLSIZE
Defines the number of tiny data buffers. It is recommended that
you specify at least 256 tiny data buffers
PSF relies on TCP to detect when a connection with a TCP/IPattached printer or an Axis Network Print Server is no longer
available. When no data has been exchanged between PSF and its
connection partner, TCP sends keep-alive probes to the connection
partner periodically. These periodic probes, called keep-alive
transmissions, enable TCP to discover when a connection is no
longer usable even if the connection partner is abruptly powered off
or is no longer accessible through the network.
KEEPALIVEOPTIONS
The frequency of keep-alive transmissions is controlled by the
INTERVAL parameter on the KEEPALIVEOPTIONS statement. The
frequency applies to all TCP applications that direct TCP to send
keep alive transmissions. The default frequency is after about two
hours of inactivity.
We recommend that you specify a shorter interval than the default,
such as 10 minutes, for the interval between keep-alive
transmissions.
Also, if any target host on you network requires that the keep-alive
packet contains data, specify SENDGARBAGE TRUE
GATEWAY
The Packet_size parameter of the GATEWAY statement defines the
maximum transmission unit (MTU) for the MVS host. The MTU size
must not exceed the maximum size that can be sent through the
control unit; if it does, transmission problems will occur.
The MTU size should be 2000 bytes and the MTU size for the MVS
host should be the same as the MTU size for the printer.
For values in the GATEWAY statement other than the packet size,
specify the values that are correct for your installation.
For more information about the TCP/IP profile and the statements
described in this section, please refer to:
•
•
Configuring the
Axis Network Print
Server
IBM TCP/IP MVS Customization and Administration Guide
IBM TCP/IP Performance and Tuning Guide
Follow the instructions below to configure your Axis Network Print
Server using a standard Web browser:
1. Start a Web browser, e.g. Internet Explorer or Netscape Navigator.
2. Enter the IP address or the host name of the Axis Network Print Server in
the location field and press the Enter key on your keyboard. The internal Web
pages of the Axis Network Print Server will appear.
Note:
To protect the Admin pages and the Configuration Wizard from unauthorized use, enter a
password (default Pass) in the Root Password field under Admin | General Settings.
52
AXIS 5570e / AXIS 5670e User’s Manual
Setting Up - IBM Mainframe (zSeries)
Note for IPDS printing:
In the Configuration Wizard, you can choose between PCL or PostScript printing. Choose the
printer language that corresponds to your printer.
3. Click the Configuration Wizard for IBM sessions button.
4. Click the Add Session button. This will start the Configuration Wizard
which is a step-by-step guide through the required IBM configuration
settings.
Verifying the
communication
You can verify the communication between the MVS system and the Axis
Network Print Server by pinging the print server from the MVS system. A
successful ping indicates that the MVS system can communicate with the
Axis Network Print Server.
From an TSO session, enter the following command:
TSO PING <IP_address>
Note:
The IP address is the IP address of the Axis Network Print Server.
In JES2, enter the following command from the System Display and
Search Facility (SDSF) menu 6:
ping <IP_address>
Note:
The IP address is the IP address of the Axis Network Print Server.
Here is an example of a successful ping:
EZA0458I Ping V3R1:
Pinging host 10.50.45.200
(Use ATTN to interrupt.)
EZA0463I PING: Ping #1 response took 0.055 seconds
Successes so far = 1
And here is an example of an unsuccessful ping:
EZA0458I Ping V3R1:
Pinging host 10.50.45.200
(Use ATTN to interrupt.)
EZA0464I PING: Ping #1 timed out
If the ping is not successful, make sure the Axis Network Print Server is
configured according to the instructions in Setting the IP Address, on
page 16 and in Configuring the Axis Network Print Server, on page 43.
If these items are all in order, consult your TCP/IP network administrator.
JES definitions
When a TCP-attached printer is to be used with JES, it must be defined for
deferred-printing mode. To use a PSF printer for deferred printing under
JES, you must first code JES initialization statements to define FSSs and
FSAs for PSF printers. For JES2, the FSS is defined by an FSS statement,
and the FSA is defined by a PRTnnnn statement. For JES3, the FSS is
AXIS 5570e / AXIS 5670e User’s Manual
53
Setting Up - IBM Mainframe (zSeries)
defined by an FSSDEF statement, and the FSA is defined by a DEVICE
statement.
The maximum number of FSSs and FSAs that are supported are:
• FSSs = 2000
• FSAs per FSS = 64
The actual number of FSAs per FSS depends on several factors like:
•
•
•
•
JES2 Initialization
The virtual region size below the 16-megabyte line
The number and the size of form definitions and page definitions
The number of buffers specified (BUFNO) for channel-attached printers
The block sizes of the font, page segment, overlay, form definition, and
page definition libraries
The example below shows a sample JES2 statements for a TCP/IPattached Axis Network Print Server:
FSS (FSS1) PROC=SAMPPROC,HASPFSSM=HASPFSSM
PRT1
FSS=FSS1,MODE=FSS,PRMODE=(LINE,PAGE,),
CLASS=C,UCS=0,SEP=NO,SEPDS=NO,CKPTPAGE=100
START=YES,MARK=NO,TRKCELL=YES
Note:
This is only an example. For specific coding for JES parameters, refer to the JES publication
for the level of JES you are using.
The following paragraphs describe the JES2 initialization statements
shown above, which are typical of the JES2 statements used with PSF.
For more detailed descriptions of all JES2 initialization statements, refer
to the JES2 initialization and tuning publication for your operating
system.
FSS Statement
54
The FSS initialization statement is optional but recommended. If it is
omitted, JES2 generates a default FSS for that device. The FSS
initialization statement defines an FSS to JES2. The FSS statement is
associated with one or more PRTnnnn statements that define each printer
FSA. For a description of all FSS parameters, refer to the JES2
initialization and tuning publication for your operating system. The FSS
statement contains the following parameters for PSF:
AXIS 5570e / AXIS 5670e User’s Manual
Setting Up - IBM Mainframe (zSeries)
PRTnnnn Statement:
FSS Statement
Explanation
FSS (fasname)
Specifies the unique 1- to 8-character name of a particular FSS. This name is
referenced in the PRTnnnn statement for each printer FSA that is associated
with this FSS. When you start the first printer that has an FSA definition for
that FSS, an FSS address space is created for PSF. PSF manages this FSS and the
printer FSA for the first printer. If you start a second printer with an FSA
definition for the same FSS, PSF manages a separate FSA for the second printer
in that FSS.
PROC
Specifies a procedure for starting the PSF FSS. The procedure, which must be
defined before that FSS is started, is a member of either SYS1.PROCLIB or a
library concatenated to SYS1.PROCLIB.
HASPFSSM
Specifies the 1- to 8-character name of the load module that is loaded into the
PSF FSS address space. This load module contains the various FSI service
routines that JES2 supplies. For PSF, specify the default value
(HASPFSSM=HASPFSSM).
A PRTnnnn statement, which is required to define each printer nnnn
statement FSA, is associated with an FSS statement. Each printer FSA
should have a unique PRTnnnn name that must match the label on the
CNTL, ENDCNTL, and PRINTDEV statements for the PSF startup procedure
specified in the PROC parameter.
Note:
The label on the PRINTDEV statement must be 8 characters or fewer. PSF accepts the
PRTnnnn, PRINTnn, and PRINTERn formats. PRTnnnn is the recommended format.
The PRTnnnn parameters create JES2 default values that are used unless
other values are specified in the application program JCL. The PRTnnnn
statement contains the following parameters:
PRTnnnn
Statement
Explanation
CKPTPAGE
Specifies the number of pages between data-set checkpoints. If checkpoint
intervals are too frequent, printer performance is significantly reduced. If
intervals are too infrequent, and a PSF error occurs, the job has to be
reprocessed from the last checkpoint. In this case, printer performance is
significantly reduced if PSF errors continue to occur. The recommended
starting value is 100.
CLASS
Specifies the output classes processed by the printer. By defining print classes
you can handle disabled mechanisms.
FSS
Specifies the FSS for this device and must match the FSA name specified in
the corresponding FSS statement. This parameter is required.
MARK
MODE
AXIS 5570e / AXIS 5670e User’s Manual
Enables form markings to be placed on the job trailer pages. For the Axis
Network Print Server you should set this parameter to NO.
Note: This parameter is new in JES2 and replaces the MARK | NOMARK
parameter.
Specifies that the printer is managed by an FSS. This parameter is required.
55
Setting Up - IBM Mainframe (zSeries)
PRTnnnn
Statement
Explanation
PRMODE
Specifies the data-set processing modes supported for the printer. It lists all
the PRMODE values that the printer accepts. If the Axis Network Print Server is
connected to a PostScript printer, the correct setting is
PRMODE=(PAGE,LINE,).. This setting indicates that composed-page
and line data sets can be printed.
Enables job-header and job-trailer separator pages to be produced.
SEP
Note1: If the Distributed Print Function (DPF) of PSF/2 is installed, you may
need to set this parameter to YES.
Note2: This parameter is new in JES2 and replaces the SEP | NOSEP parameter.
Enables formatted data-set header separator pages to be produced.
SEPDS
START
Note: This parameter is new in JES2 and replaces the SEPDS | NOSEPDS
parameter.
Specifies the way that the printer is started. The parameter value NO specifies
that the printer is to be started by an operator command. The parameter value
YES specifies that the printer, if it is ready, is to start automatically when
JES2 starts processing.
Note: This parameter is new in JES2 and replaces the DRAIN | START
parameter.
JES3 Initialization
TRKCELL
Specifies whether track-cell despooling is to be used or not. It is recommended
to set this parameter to YES.
UCS
Specifies a default font. If you want to select a font in the startup procedure
instead of the JES2 default font, you should set this parameter to 0.
Below is sample JES3 statements for an TCP/IP attached Axis Network
Print Server. In the example the JNAME=PRT1 has been used.
FSSDEF,TYPE=WTR,FSSNAME=FSS3,PNAME=SAMPPRO3,SYSTEM=SYS1,TERM=NO
DEVICE,DTYPE=PRTAFP1,JNAME=PRT1,JUNIT=(,SYS1,,ON),FSSNAME=FSS3
MODE=FSS,PM=(LINE,PAGE,),CHARS=(YES,GT12),
CARRIAGE=(TES,A868),CKPNTPG=100,HEADER=YES,WC=(C)
Note:
This is only an example. For specific coding for JES parameters, refer to the JES publication
for the level of JES you are using.
The following paragraphs describe the JES3 initialization statements
shown above, which are typical of the JES3 statements used with PSF.
For more detailed descriptions of all JES3 initialization statements, refer
to the JES3 initialization and tuning publication for your operating
system.
FSSDEF Statement:
56
The FSSDEF initialization statement is optional but recommended. If it is
omitted, JES3 generates a default FSS for the printer being invoked.
AXIS 5570e / AXIS 5670e User’s Manual
Setting Up - IBM Mainframe (zSeries)
The FSSDEF statement can contain the following parameters:
FSSDEF
Statement
Explanation
TYPE
Specifies that the FSS is an output writer for deferred printing. This parameter is
required.
FSSNAME
Specifies the unique name of a particular FSS. This parameter is required.
PNAME
Specifies a procedure for starting a specific PSF FSS. The procedure, which must
be defined before the FSS is started, is a member of the procedure library
defined by the STCPROC parameter of the STANDARDS statement or of the
IATPLBST procedure library. Different FSSDEF initialization statements can refer
to the same startup procedure.
The PNAME parameter specifies either a startup procedure supplied with PSF, or
one of your organization’s procedures.
DEVICE Statement:
SYSTEM
Specifies the JES3 processor on which the FSS is run. The name must match the
NAME parameter in the MAINPROC statement for the processor.
TERM
Specifies the way that the FSS is terminated. The parameter value YES indicates
that the FSS is terminated if the JES3 global address space is terminated by a
*RETURN or *DUMP operator command.
A DEVICE statement is required for each printer. The DEVICE parameters
create JES3 default values that are used unless other values are specified
in the JCL application program. The DEVICE statement can contain the
following parameters:
Device
Statement
Explanation
CARRIAGE
Specifies the JES default page definition.
The value YES specifies that the page definition can be changed during
startup procedures.
The value NO specifies that the page definition cannot be changed during
startup procedures.
The value aaaa specifies that the un-prefixed name, 1 to 4 characters
long, of the page definition is to be used as default. The name specified
here, or the JES3 system default, is the PSF default page definition.
CHARS
Specifies a default JES3 font.
CKPNTPG
Specifies the number of pages between data-set checkpoints. If checkpoint
intervals are too frequent, printer performance is significantly reduced. If
intervals are too infrequent, and a PSF error occurs, the job has to be reprocessed
from the last checkpoint. In this case, printer performance is significantly
reduced if PSF errors continue to occur. The recommended starting value is 100.
DTYPE
Identifies the printer device type. For the Axis Network Print Server you should
specify the parameter value PRTAFP1. This parameter is required.
FSSNAME
Specifies a unique FSS for this printer DEVICE statement. The value must match
the value coded for the FSSNAME parameter in the corresponding FSSDEF
statement.
HEADER
Specifies if job and data set header pages are printed. If DPF is installed, you may
need to specify HEADER=YES.
JNAME
Specifies the name of the printer FSA. Each printer FSA should have a unique
JNAME. This unique JNAME is 8 characters or fewer and must correspond to its
label on the CNTL, ENDCNTL, and PRINTDEV statements for the PSF
startup procedure specified in the PNAME parameter. This parameter is required.
AXIS 5570e / AXIS 5670e User’s Manual
57
Setting Up - IBM Mainframe (zSeries)
Device Statement
Explanation
JUNIT
Specifies:
1. The device address (host-connected, channel-attached, non-SNA printers
only). Do not specify a device address for the Axis Network Print Server when
using TCP/IP attachment.
2. The name of the processor to which the device is attached
3. A destination class for messages about the device
4 .Whether the device is initially online or offline
This parameter is required.
Defining the
printer to PSF
MODE
Specifies that the printer is managed by an FSS. This parameter is required.
PM
Specifies which data-set processing mode is supported. For the Axis Network
Print Server attached to Postscript printers, the correct setting is
PRMODE=(LINE,PAGE,), indicating that composed-page and line data
sets can be printed.
WC
Specifies the print output class that the printer is to process. You may want to
consider handling disabled mechanisms by defining print classes.
Each Axis Network Print Server must be defined to PSF with a PRINTDEV
statement in the PSF startup procedure. The following keywords are
required on the PRINTDEV statement:
• IPADDR='xxx.xxx.xxx.xxx'
• PORTNO='xxxx'
The IPADDR parameter specifies the IP address of the Axis Network Print
Server in dotted-decimal notation.
Note:
Do not specify a host name in place of the dotted-decimal address.
The PORTNO keyword specifies the TCP/IP port to use for the print
session. This port number must match the port number set up for the Axis
Network Print Server in Configuring the Axis Network Print Server, on
page 43.
Below is a sample procedure, APSWPROT, which you can modify to suit
your installation. The PRINTDEV statement includes the required IPADDR
and PORTNO keywords. In the PRINTDEV example below, the TCP/IP port
number 5100 is used, but any port, larger that 1024, can be used as long
as the same port is set up in the Axis Network Print Server.
The APSWPROT procedure contains JCL parameters to produce a startup
procedure for either 240-pel and 300-pel printers, but the references to
300-pel resolution are commented out. To create separate startup
procedures, make two copies of APSWPROT, and then follow the
commented instructions in APSWPROT. Keep one unchanged copy as your
startup procedure for a resolution of 120 or 240 pels. In the second copy,
delete or comment out all references to 240-pel resolution, and make all
references to 300-pel resolution active. This changed copy is your startup
procedure for 300-pel resolution.
If you want to print both 240-pel and 300-pel AFP/IPDS jobs, create two
58
AXIS 5570e / AXIS 5670e User’s Manual
Setting Up - IBM Mainframe (zSeries)
separate FSAs, one for jobs with resolution of 120 or 240, and one for
jobs with resolution of 300 pels. The 240-pel resolution FSA uses 240-pel
resources, and the 300-pel resolution FSA uses 300-pel resources. Both
FSAs are defined to drive the same printer; however, only one FSA can be
active at one time for a given printer. You should define separate classes
or destinations for each FSA. Your installation must route the appropriate
jobs to the appropriate class or destination. The two FSAs can be defined
in the same or in separate startup procedures.
//APSWPROT PROC
//********************* THE PSF TCP/IP WRITER PROCEDURE **********************
//*
//*01* MODULE-NAME = APSWPROT
//* $MOD(APSWPROT) COMP(APS) PROD(PSF) : RELEASE 2.2.0
//*
//*01* DESCRIPTIVE-NAME = START PROCEDURE FOR PSF:
//*
//*
TCP/IP ATTACHED DEVICES
//*
//*01* STATUS = VERSION 2, RELEASE 2, LEVEL 0
//*
//*01* FUNCTION = THIS PROCEDURE IS COPIED FROM THE
//*
DISTRIBUTION LIBRARY TO SYS1.PROCLIB.
//*
THIS COPY IS PERFORMED BY MACRO ‘SGAPS5PR’.
//*
//*01* NOTES = THE FULL NAME OF THE DEFAULT PAGEDEF IS
//*
//*
//*
//*
//*
//*
//*
//*
//*
P1A06462.
THE FULL NAME OF THE DEFAULT FORMDEF IS
F1A10110.
THE FULL NAMES OF THE DEFAULT FONTS ARE
X0GF10, X0GS10, X0TU10, AND X0GU10
THE FULL NAME OF THE SEPARATOR PAGE PAGEDEF IS
P1V06483
THE FULL NAME OF THE SEPARATOR PAGE FONT IS
X0GT15
//*
AXIS 5570e / AXIS 5670e User’s Manual
59
Setting Up - IBM Mainframe (zSeries)
Example continues
CONT...
//* REQUIRED ACTIONS =
//*
RESOLUTION - THIS START PROCEDURE IS SET UP FOR DRIVING
//*
A TCP/IP DEVICE AT 240 PEL RESOLUTION. TO CHANGE IT
//*
TO DRIVE 300 PEL RESOLUTION TCP/IP ATTACHED DEVICES:
//*
//*
//*
A) COMMENT OUT THE FIRST PRINTDEV STATEMENT AND UNCOMMENT
THE SECOND PRINTDEV STATEMENT
//*
//*
B) THE FONT02 DATA SET MUST CONTAIN THE CONVERTED
//*
DEFAULT FONTS LISTED IN THE PRINTDEV.
//*
THE FONTS ARE CONVERTED USING THE FONT
//*
CONVERSION UTILITY APSRCF30. SEE THE PSF
//*
SYSTEM PROGRAMMING GUIDE.
//*
//*01* CHANGE-ACTIVITY :
//* $H1=LAPS0001, HAF1103, 080195 DKU1JAU : TCP/IP SUPPORT
//*
//**** END OF SPECIFICATIONS ***/
//STEP01
EXEC PGM=APSPPIEP,REGION=4096K
//JOBHDR OUTPUT PAGEDEF=V06483,
/* JOB SEPARATOR PAGEDEF
//
/* JOB SEPARATOR FORMDEF
*/
/* JOB SEPARATOR PAGEDEF
*/
FORMDEF=A10110,CHARS=GT15
//JOBTLR OUTPUT PAGEDEF=V06483,
//
FORMDEF=A10110,CHARS=GT15
/* JOB SEPARATOR FORMDEF
*/
//DSHDR
OUTPUT PAGEDEF=V06483,
/* DS
SEPARATOR PAGEDEF
*/
//
FORMDEF=A10110,CHARS=GT15
/* DS
SEPARATOR FORMDEF
//MSGDS
OUTPUT PAGEDEF=V06462,
/* MESSAGE DATASET PAGEDEF
//
FORMDEF=A10110
//FONT01
60
*/
DD
DSN=SYS1.FONTLIBB,
//
DISP=SHR
//FONT02
DD
//
DISP=SHR
//PSEG01
DD
//
DISP=SHR
//OLAY01
DD
//
DISP=SHR
DSN=SYS1.FONT300,
DSN=SYS1.PSEGLIB,
DSN=SYS1.OVERLIB,
//PDEF01
DD
//
DISP=SHR
DSN=SYS1.PDEFLIB,
//FDEF01
DD
//
DISP=SHR
DSN=SYS1.FDEFLIB,
*/
*/
/* MESSAGE DATASET FORMDEF
*/
/* SYSTEM FONTS - 240 PEL
*/
/* SYSTEM FONTS - 300 PEL
*/
/* SYSTEM PAGE SEGMENTS
*/
/* SYSTEM MEDIUM OVERLAYS
*/
/* SYSTEM PAGEDEFS
*/
/* SYSTEM FORMDEFS
*/
AXIS 5570e / AXIS 5670e User’s Manual
Setting Up - IBM Mainframe (zSeries)
Example continues
CONT...
//* ************************************************************
//*
*/
PRINTDEV
//* ************************************************************
//PRT1
CNTL
//PRT1
PRINTDEV FONTDD=*.FONT01, /* 240 PEL FONT LIBRARY DD
//*
/* <-- SEE REQUIRED ACTIONS
//*
/* ABOVE
//*PRT1
PRINTDEV FONRDD=*.FONT02, /* 300 PEL FONT LIBRARY DD
*/
*/
*/
*/
*/
//*
/* <-- SEE REQUIRED ACTIONS
//*
/* ABOVE
*/
*/
//
OVLYDD=*.OLAY01,
/* OVERLAY LIBRARY DD
*/
//
PSEGDD=*.PSEG01,
/* SEGMENT LIBRARY DD
*/
//
PDEFDD=*.PDEF01,
/* PAGEDEF LIBRARY DD
*/
//
FDEFDD=*.FDEF01,
/* FORMDEF LIBRARY DD
*/
//
JOBHDR=*.JOBHDR,
/* JOB HEADER SEPARATOR
*/
/* OUTPUT
*/
JOBTRLR=*.JOBTLR,
/* JOB TRAILER SEPARATOR
*/
/* OUTPUT
*/
//*
//
//*
//
DSHDR=*.DSHDR,
//*
/* DATA SET HEADER
*/
/* SEPARATOR
*/
*/
//
MESSAGE=*.MSGDS,
/* MESSAGE DATA SET OUTPUT
//
BUFNO=5,
/* NUMBER OF WRITE DATA BUFFERS*/
//
PAGEDEF=A06462,
/* DEVICE PAGEDEF DEFAULT
*/
//
FORMDEF=A10110,
/* DEVICE FORMDEF DEFAULT
*/
//
CHARS=(GF10,
/* DEVICE
*/
//
GS10,TU10,GU10),
/* DEFAULT FONT SET
*/
//
PIMSG=YES,
/* ACCUMULATE DATA SET
*/
//*
/* MESSAGES
*/
DATACK=BLOCK,
/* REPORT ALL DATA-CHECK
*/
/* ERRORS
*/
//
TRACE=NO,
/* CREATE INTERNAL TRACE
*/
//
FAILURE=WCONNECT,
/* PSF ACTION ON PRINTER
*/
//
//*
//*
/* FAILURE
*/
//
TIMEOUT=REDRIVE,
/* PSF ACTION ON TIMEOUT
*/
//
MGMTMODE=IMMED,
/* PRINTER MANAGEMENT MODE
*/
//
DISCINTV=40,
/* DISCONNECT INTERVAL IN
*/
/* SECONDS
*/
//*
//
ADDRESS
IPADDR=’xxx.xxx.xxx.xxx’
*/
/* Axis Network Print Server IP
//
PORTNO=’5100’,
/* TCP/IP PORTO
//PRT1
ENDCNTL
*/
Although it is not recommended, it is possible to drive the printer with
just one FSA, if one of the following conditions are met:
•
All the resources in the resource libraries are resolution-independent,
and all the jobs that use inline resources or user libraries contain
resources that are resolution-independent.
• All jobs that request a resolution that is different from the resolutiondependent resources in the PSF system and security libraries contain the
resources at the requested resolution, either as inline resources or in the
user's library.
Even if a PSF user requests 120-pel resolution for an AFP print job being
sent to the printer, PSF requires 240-pel resources from the library. Do
not store 120-pel resources in the library.
AXIS 5570e / AXIS 5670e User’s Manual
61
Setting Up - IBM Mainframe (zSeries)
Starting and Stopping
the PSF/MVS Printer
Starting the Printer
When operating the Axis Network Print Server when emulating a TCP/IP
attached IPDS printer, you should use JES operator commands, just as if
the printer were channel-attached or SNA-attached.
To start a TCP/IP-attached printer, do the following:
1. Start TCP/IP.
2. Power on the printer(s).
3. Power on the Axis Network Print Server.
4. Start the printer FSA as indicated below.
Before starting a PSF FSS, you must have a cataloged startup procedure
in SYS1.PROCLIB or any other system procedure library. This procedure
specifies PSF initialization parameters and libraries that contain system
and installation resources. The name of this procedure can be specified in
the FSSDEF statement of the JES initialization deck. If the name is
omitted, JES3 supplies a default name, that is chosen for the defined
printer.
When you install PSF, you must create or update the required libraries
referenced by the startup procedure, and you should consider any need to
increase the region size, as specified in the EXEC statement, to
accommodate resources and an increased number of printer FSAs. The
startup procedure can also specify defaults that cannot be set with JES
initialization statements for printer FSA definitions.
Stopping the Printer
You can stop a TCP/IP-attached printer in several ways but this is the
recommended method:
Stop the PSF FSA for the printer by entering the following command
from the MVS console.
JES2:
$Pprinter-name
JES3:
*VARY printer-name, OFF
*CANCEL printer-name
The variable printer-name specifies the name of the printer FSA as defined in JES
definitions, on page 53.
You can now disconnect the Power Adapter from the Axis Network Print
Server.
62
AXIS 5570e / AXIS 5670e User’s Manual
Adding Printers in Windows
Section 6
Adding Printers in Windows
Having connected the Axis Network Print Server to your network, as
described in “Connect the Hardware” on page 14, this section describes
how to install the Axis Network Print Server in the Windows
environment. Identify your Windows platform and follow the installing
instructions from the list below.
Overview of
Installation Methods
Refer to the table below to determine the most appropriate installation
method according to your computer environment:
Windows
Platform
Windows 2000,
XP, Server 2003
Windows 2000
Printing Protocol
TCP/IP (LPR)
NetBIOS/NetBEUI
Method
See...
AXIS AddPrinter
Wizard
“Adding Printers in Windows 2000 /
XP / 2003 using AXIS AddPrinter Wizard” on page 64
Windows Add Printer
Wizard
“Adding Printers in Windows 2000 /
XP / 2003 using Windows Add Printer
Wizard” on page 66
Microsoft
LPR Monitor
“Adding Printers in Windows 2000 /
XP / 2003 using the Microsoft LPR
Monitor” on page 72
AXIS Print Monitor
software
“Adding NetBIOS/NetBEUI Printers in
Windows 2000 using AXIS Print Monitor” on page 77
TCP/IP (LPR)
Windows Add Printer
Wizard
Windows NT
Adding Printers in Windows NT Using
the Microsoft LPR Monitor, on page
74
NetBIOS/NetBEUI
Adding Printers over NetBIOS/NetBEUI in Windows NT using AXIS Print
Monitor, on page 78
TCP/IP (LPR)
“Adding Printers in Windows 98 and
Me over TCP/IP using AXIS Print Monitor” on page 79
AXIS Print Monitor
software
Windows 98, Me
NetBIOS/NetBEUI
“Adding Printers in Windows 98 and
Me over NetBIOS/NetBEUI using AXIS
Print Monitor” on page 81
If you intend to operate your Axis Network Print Server in a multiprotocol environment, you should also proceed to the other relevant
sections in this manual.
Client/Server Network
For client/server printing, each computer sends print jobs through a
network server computer.
The printer must first be installed on the server computer (from the Add
Printer Wizard, AXIS Print Monitor) and then shared on the network,
which makes it a network printer. It will then appear as a Network
Printer (in Windows Add Printer Wizard and in AXIS Print Monitor) on
the client computers. Each client computer must install the appropriate
printer drivers in order to print properly.
For Windows 98 and Me, it is only necessary to install AXIS Print Monitor on a server for
client/server printing.
AXIS 5570e / AXIS 5670e User’s Manual
63
Adding Printers in Windows
Peer-to-Peer Network
In Peer-to-Peer networks, each computer prints directly to the network
printer. The network printer appears as a Local Printer (in Windows Add
Printer Wizard and in AXIS Print Monitor), and needs to be added to each
client computer that wants to print. Each client computer must install the
appropriate printer drivers in order to print properly.
In Windows 98 and Me, AXIS Print Monitor must be installed on all (printing) client
computers for Peer-to-Peer printing.
SNMP Device Index
When using the TCP/IP protocol (and if the printer driver permits), the
print server can use SNMP Status to find out if the printer is ready to
accept a new job. See “SNMP Device Index” on page 276.
Adding Printers in Windows 2000 / XP / 2003 using AXIS AddPrinter Wizard
AXIS AddPrinter is a Wizard that locates your network printers and helps
you install them in your Windows environment. When you have
completed the Wizard, the network printer is ready for use. To install a
network printer you must be logged in as an Administrator or be a
member of the Administrators' group.
1. Install AXIS AddPrinter Wizard on all Windows 2000, Windows XP and
Windows Server 2003 workstations that will print via the print server.
2. Before you continue, ensure that the print server is properly connected to
the printer, network and power.
3. Start AXIS AddPrinter. Click Next. The Wizard will perform an automatic
search for all Axis network printers, which is indicated by the progress bar
at the bottom of the screen.
4. Select a printer from the Select Network Printer list and click Next.
If the printer does not appear, see Easy Access to All Network Printers,
below.
64
AXIS 5570e / AXIS 5670e User’s Manual
Adding Printers in Windows
5. The Wizard searches for a suitable printer driver.
If a suitable driver is not found, you will be asked to select a driver, otherwise
the Wizard suggests which Printer Model and Printer Driver to use.
Click Change driver to select another driver, or click Finish to accept and
install the suggested driver.
The installation is complete and you can start using the network printer.
Easy Access to All
Network Printers
The Wizard's Select Network Printer list also provides quick and easy
access to all connected and configured network printers.
Find...
If the print server is located outside your local subnet it will not appear in
the list. This may be the case if your router blocks SLP traffic. Click Find.
Enter the IP address or host name displayed on the print server’s Test page
and click OK. Example: 192.168.3.191 or AXIS181cf0
Refresh
If the print server has just been switched on, the printer has not had time
to report its presence. This process can take a few minutes. In this case,
Printer Model is stated as No printer connected. Click Refresh to rescan
your local network segment for available print servers and update the
status. If you still do not see the expected values, click Help and select
Troubleshooting.
Set IP
To set or change the IP address, select the print server and click Set IP.
Decide whether you want to configure the IP settings manually or want
the Wizard to suggest a static IP address.
Example: Select Suggest... and click OK. Confirm — or modify — the
Wizard’s suggested IP settings. Click OK.
Note: The Suggest... option is only available when the computer has one
network card.
AXIS 5570e / AXIS 5670e User’s Manual
65
Adding Printers in Windows
Go Straight to the
Print Server’s Web
Interface
Right-click on a printer in the Select Network Printer list and select Print
server home page to configure the print server from its embedded Web
pages.
Adding Printers in Windows 2000 / XP / 2003 using Windows Add Printer Wizard
Follow the instructions below to use the standard Windows method for
adding a network printer in Windows 2000/ Windows XP
(Windows XP Professional is described in this example).
Windows XP:
1. Go to Start | Printers and Faxes and click the Add a Printer icon to start
the Add Printer Wizard. Click Next.
(Windows XP Home Edition: Choose Start | Control Panel | Printers and
Faxes | Add a Printer to start the Windows Add Printer Wizard)
Windows 2000:
1. Go to Start | Settings | Printers and click the Add Printer icon to start
the Add Printer Wizard. Click Next.
66
AXIS 5570e / AXIS 5670e User’s Manual
Adding Printers in Windows
2. In the Wizard, select Local Printer attached to this computer.
Make sure the Automatically detect and install my Plug and Play printer
check box is not checked. Click Next.
3. Click the Create a new port radio button and select Standard TCP/IP Port
from the list. Click Next and the Add Standard TCP/IP Printer Port Wizard
starts. Click Next.
4. Enter the IP address of the print server (Example: 192.168.3.191)
The Port Name field will be filled in automatically when you enter the IP
address. Add the port you want to use as a suffix (optional).
AXIS 5570e
Physical Port
Add suffix
Entry example
USB port
Type _USB1
192.168.3.191_USB1
LPT1 (parallel port)
Type _LPT1
192.168.3.191_LPT1
If you have an old version of Windows, it will not detect the USB port. If
so, type “_LPT2” instead of “_USB1” in the example above, e.g.
192.168.3.191_LPT2.
For additional information, see “*Tcpmon.ini” on page 71.
AXIS 5570e / AXIS 5670e User’s Manual
67
Adding Printers in Windows
AXIS 5670e
Physical Port
Add suffix
Entry example
LPT1 (parallel port)
Type _LPT1
192.168.3.191_LPT1
LPT2 (parallel port)
Type _LPT2
192.168.3.191_LPT2
COM1 (serial port)
Type _COM1
192.168.3.191_COM1
5. Click Next.
6. In the Additional Port Information Required window, enter the Device Port
you want to use. You will see the available ports in a drop-down menu:
AXIS 5570e
Physical Port
Add suffix
Entry example
USB port
Type _USB1
192.168.3.191_USB1
LPT1 (parallel port)
Type _LPT1
192.168.3.191_LPT1
If you have an old version of Windows, it will not detect the USB port. If
so, type “_LPT2” instead of “_USB1” in the example above, e.g.
192.168.3.191_LPT2.
For additional information, see “*Tcpmon.ini” on page 71.
AXIS 5670e:
68
Physical print server port connected to printer
Choose port
LPT1 (parallel port)
LPT1
LPT2 (parallel port)
LPT2
COM1 (serial port)
COM1
AXIS 5570e / AXIS 5670e User’s Manual
Adding Printers in Windows
7. Click Next.
Click Next and Finish
AXIS 5570e / AXIS 5670e User’s Manual
69
Adding Printers in Windows
8. Select Manufacturer and Printer from the driver list. Click Next.
9. Choose whether you want to keep the existing driver or to replace it. If you
already have the printer’s driver installed, you will be asked whether to keep
it or to replace it.
10. Click Next. Supply a name for the printer and choose whether you want to
make it your default printer. Click Next.
70
AXIS 5570e / AXIS 5670e User’s Manual
Adding Printers in Windows
11. Choose whether you want to share the printer with other network users,
print a test page, etc. Select the appropriate radio button and click Next and
Finish.
12. Print a test page to verify your installation.
You have now completed the installation.
*Tcpmon.ini
If you have an old version of Windows, the USB port will not be recognized.
For the USB port to appear as an option in the Windows Device Port list (see Step 5 above ), you
must install Axis tcpmon Upgrade Utility, a script that aids Windows in recognizing the USB port.
This script upgrades the tcpmon.ini file (in the system32 directory) by adding new Axis print
server ports in the Windows Available Ports list. The old tcpmon.ini file will be saved as
tcpmon.ini_bak in the same directory, no other information will be affected. You have to be
logged in as an Administrator to use this program.
The program is available here: ftp.axis.com/pub_soft/prt_srv/utility/tcpmon
AXIS 5570e / AXIS 5670e User’s Manual
71
Adding Printers in Windows
Adding Printers in Windows 2000 / XP / 2003 using the Microsoft LPR Monitor
This section describes how to set up a Windows 2000/XP/2003 server for
LPR printing over the TCP/IP protocol, using the built-in Microsoft LPR
Monitor i.e. Print Services for UNIX.
Note:
See “Alternative Method for LPR Printing” on page 73 for instructions on how
to set up printing over LPR without installing Print Services for Unix.
Basic Setup
Preparing for
LPR Printing
If you have not already done so, you should perform the TCP/IP basic
setup procedures prior to installing a printer for LPR printing.
Follow the following steps to prepare for LPR printing:
1. Open the Control Panel.
2. Click Add/Remove Programs.
3. Click Add/Remove Windows Components.
4. Check Other Network File and Print Services and click Details.
5. Check Print Services for Unix and click OK.
6. Click Next and Finish.
7. Close Add/Remove Programs and the Control Panel.
Installing an LPR
printer
Windows XP:
Windows 2000:
Follow the instructions below to use the standard Windows method for
installing an LPR printer in Windows 2000/XP/2003:
1. Go to Start | Printers and Faxes and click the Add a Printer icon to start
the Add Printer Wizard. Click Next.
1. Go to Start | Settings | Printers and click the Add Printer icon to start
the Add Printer Wizard. Click Next.
2. Select the appropriate radio button: Local Printer. Click Next.
3. Click the Create a new port radio button and select LPR Port from the list.
Click Next.
72
AXIS 5570e / AXIS 5670e User’s Manual
Adding Printers in Windows
4. Enter the name of the server (or its IP address) in the field Name and address
of server providing lpr (Example: AXIS100086) and enter the port you want
to use in the field Name of printer or print queue on that server (Example:
LPT1). Click OK.
Ports available
USB port
Parallel port 1 Parallel port 2
Serial port
AXIS 5570e
USB1
LPT1
—
—
AXIS 5670e
—
LPT1
LPT2
COM1
End the Wizard in the usual manner: select Manufacturer and Printer,
keep/replace driver, name the printer, make it default or not, share it or not
and finally decide whether you want to print a test page.
Client/Server Printing
Select Network printer instead of Local Printer in Step 2 above if your
print server has already been installed by the administrator on another
computer. Follow the instructions in the Add Printer Wizard to complete
the installation.
Important!
• Make sure that the Automatically detect and install my Plug and Play printer checkbox is
not checked
• Press F1 to access the Windows online help system if you need additional help when
installing a printer/print server using this method.
Alternative Method for
LPR Printing
If you wish to print over LPR but do not wish to install Print Services for
Unix you can do this by changing the printing protocol after having
installed the printer using the Standard TCP/IP method, see “Adding
Printers in Windows 2000 / XP / 2003 using Windows Add Printer
Wizard” on page 66 for instructions. LPR is chosen by default with this
method.
Once the printer is installed, follow these instructions to change the
printing protocol:
1. Go to Start | Settings | Printers.
2. Double-click the installed printer.
3. Select Properties from the Printer menu.
4. Click the Ports tab.
5. Click the Configure Port button.
6. Click the LPR radio button and enter the queue name (PR1, PR2...).
7. Click OK to finish.
AXIS 5570e / AXIS 5670e User’s Manual
73
Adding Printers in Windows
Adding Printers in Windows NT Using the Microsoft LPR Monitor
If you have not already done so, you should perform the TCP/IP basic
setup procedures prior to installing a printer for LPR printing.
Preparing for
LPR Printing
In the Control Panel, double-click the Network icon. Select the Services
tab. If the TCP/IP Printing entry appears, then TCP/IP is already installed.
Close the Network folder and go on to Installing an LPR printer, below.
First, prepare for LPR printing:
1. Open the Control Panel and double-click the Network icon.
2. Select Protocols.
3. Add TCP\IP Protocol.
4. Select Services.
5. Add Microsoft TCP\IP Printing.
Installing an LPR
Printer
1. Go to Start | Settings | Printers | Add Printer. Select My Computer (for
peer-to-peer printing) and click Next.
2. From the Available Ports list, choose the appropriate printer port, which will
appear as the host name or IP address of the print server. Skip to step 7.
3. If the host name or IP address of the print server you wish to use does not
appear in the list, click Add Port.
4. Choose LPR Port from Available Printer Ports and click New Port.
5. Type the print server’s name or IP address in the field Name or address of
server providing lpd (Example: 10.13.6.198). Then enter which port to use
in the field Name of printer or print queue on that server according to the
table below (Example: LPT1). Click OK and then Close.
Ports available
USB port
Parallel port 1 Parallel port 2
Serial port
AXIS 5570e
USB1
LPT1
—
—
AXIS 5670e
—
LPT1
LPT2
COM1
6. The added print server will now appear in the Available Ports list.
7. Click Next, choose an appropriate driver and finish the installation in the
normal manner.
74
AXIS 5570e / AXIS 5670e User’s Manual
Adding Printers in Windows
AXIS Print Monitor Software
AXIS Print Monitor is the recommended tool to use for network printing
in Windows NT, 98 and Me environments. AXIS Print Monitor is
available free of charge on www.axis.com
AXIS Print Monitor
Overview
AXIS Print Monitor allows the print server to be connected in the same
simple fashion as connecting a local printer. Once installed, it is
automatically initialized upon system startup. AXIS Print Monitor has
been developed for peer-to-peer printing, allowing your print jobs to be
sent directly to the print server.
Printing Environments
AXIS Print Monitor supports printing over TCP/IP (LPR and Raw TCP) and
NetBIOS/NetBEUI. To enable printing in these environments, please
ensure that the desired printing protocols are running on your client.
Peer-to-Peer Printing
The AXIS Print Monitor needs to be installed on each workstation to
perform peer-to-peer printing. Once installed, the AXIS Print Monitor
allows you to access all network printers, just as if they were connected
directly to your workstation.
Client/Server Printing
AXIS Print Monitor needs only to be installed on one server to perform
client/server printing. The installed printers must be configured to be
shared to allow clients to use them. Pop-up messages should not be
enabled on the server as they will not be displayed on the client
platforms.
Note:
AXIS Print Monitor can also be used for DOS printing. Please refer to the AXIS Print Monitor’s
Readme file for instructions. The Readme file is located in the same folder where AXIS Print
Monitor is installed on your PC.
AXIS 5570e / AXIS 5670e User’s Manual
75
Adding Printers in Windows
Adding Printers over TCP/IP in Windows NT using AXIS Print Monitor
1. Install AXIS Print Monitor on all workstations that will print via the print
server. AXIS Print Monitor is available free of charge on www.axis.com
2. To start the Add Printer Wizard, select Settings | Printers from the Start
menu and double-click the Add Printer icon.
3. The Wizard asks you to select My Computer or Network printer server.
Select My Computer, click Next.
4. Click Add Port... In the Available Ports dialog, select AXIS Port and click New
Port...
5. Select LPR (TCP/IP) as your choice of protocol and click OK.
6. Enter the IP address or the host name of your print server (Example: enter
an IP address: 192.168.3.191 or a host name: AXIS181636).
7. In the Logical Printer Name field, enter the port you wish to use; USB1,
LPT1, LPT2 or COM1. Click OK, click Close.
8. Select Manufacturer, Printers, choose a printer name and if you want to use
the printer as your default printer. Choose if you want to share the printer
and print a test page. Click Finish.
9. You may now configure the port, as described below.
Configure the Port:
1. Select Settings | Printers from the Start menu and highlight the printer
you wish to configure. Select File | Properties | Ports and click Configure
Port.
2. Choose whether error condition pop-up messages are to be displayed by
checking the box in the Configure AXIS Ports dialog. Define the frequency
at which the error messages should be displayed after retry. Click OK.
Even if the desired printer is available in the Manufacturers and Printers lists, you are advised
to use the print driver provided with the printer. This assures you of the latest driver software.
76
AXIS 5570e / AXIS 5670e User’s Manual
Adding Printers in Windows
Adding NetBIOS/NetBEUI Printers in Windows 2000 using AXIS Print Monitor
See to it that the NetBEUI protocol is installed on your client. Follow the
procedure below to install Axis Printer Ports from a Windows 2000
workstation:
1. To start the Add Printer Wizard, select Settings | Printers from the Start
menu and double-click the Add Printer icon. Start the installation by
clicking Next.
2. The Wizard asks you to select Local printer or Network printer. Select Local
printer. Click Next.
3. Click Create a new port. In the Available Ports dialog, select AXIS Port and
click Next.
4. Select NetBIOS/NetBEUI as your choice of network protocol and click OK.
5. Select the AXIS Port you want to add from the list of available ports. The
port appears as <name>.<port> (Example: AX100086.LP1). The <port> is
taken from the table below. Click OK.
Ports available
USB port
Parallel port 1 Parallel port 2
Serial port
AXIS 5570e
US1
LP1
—
—
AXIS 5670e
—
LP1
LP2
CM1
6. Choose the appropriate printer driver for your printer. Click Next and
proceed directly to step 9. It is only necessary to perform steps 7 - 8 if your
printer does not appear in the list.
Note:
Even if the desired printer is available in the Manufacturers and Printers lists, you are
advised to use the printer driver provided with the printer. This assures you of the latest driver
software.
7. Click the Have Disk... button. Insert the printer driver diskette/CD that was
provided with your printer, select the appropriate diskette/CD drive and click
OK.
8. Select the printer driver you want to install and click Next.
9. Enter an appropriate name for your printer and click Next.
10. Choose whether you want to share the printer with other network users and
click Next.
11. Choose whether you want to print a test page, click Next and then Finish.
AXIS 5570e / AXIS 5670e User’s Manual
77
Adding Printers in Windows
Adding Printers over NetBIOS/NetBEUI in Windows NT using AXIS Print Monitor
See to it that the NetBEUI protocol is installed on your client. Follow the
procedure below to install Axis Printer Ports from a Windows NT
workstation:
1. Install AXIS Print Monitor on all workstations that will print via the print
server.
2. To start the Add Printer Wizard, select Settings | Printers from the Start
menu and double-click the Add Printer icon.
3. The Wizard asks you to select My Computer or Network printer server.
Select My Computer. Click Next.
4. Click Add Port... In the Available Ports dialog, select AXIS Port and click New
Port...
5. Select NetBIOS/NetBEUI as your choice of network protocol and click OK.
6. Select the AXIS Port you want to add from the list of available ports. The
port appears as <name>.<port> (Example: AX100086.LP1). The <port> is
taken from the table below. Click OK.
Ports available
USB port
Parallel port 1 Parallel port 2
Serial port
AXIS 5570e
US1
LP1
—
—
AXIS 5670e
—
LP1
LP2
CM1
7. Close the Printer Ports window.
8. Click the Configure Port... button. Choose whether error condition pop-up
messages are to be displayed by checking the box in the Configure Axis Ports
dialog. Define the frequency at which the error messages should be
displayed after retry. Click OK. Continue the installation by clicking Next.
9. Choose the appropriate printer driver for your printer. Click Next and
proceed directly to step 12. It is only necessary to perform steps 10-11 if
your printer does not appear in the list.
Note:
Even if the desired printer is available in the Manufacturers and Printers lists, you are
advised to use the printer driver provided with the printer. This assures you of the latest driver
software.
10. Click the Have Disk... button. Insert the printer driver diskette/CD that was
provided with your printer, select the appropriate diskette/CD drive and click
OK.
11. Select the printer driver you want to install and click Next.
12. Enter an appropriate name for your printer and click Next.
13. Choose whether you want to share the printer with other network users and
click Next.
14. Choose whether you want to print a test page and then click Finish.
78
AXIS 5570e / AXIS 5670e User’s Manual
Adding Printers in Windows
Adding Printers in Windows 98 and Me over TCP/IP using AXIS Print Monitor
1. Install AXIS Print Monitor on all workstations that will print via the Axis
print server.
2. Next, start the Windows Add Printer Wizard: select Settings | Printers from
the Start menu and double-click the Add Printer icon.
3. After clicking Next in the first dialog, the Wizard asks you to select between
Local Printer and Network Printer. You must select Local Printer as the print
server emulates a local printer port. Click Next.
4. Choose the appropriate print driver for your printer. If the desired print
driver already appears within the displayed Manufacturers and printers
lists, highlight your selection, click Next and proceed directly to step 7. It
is only necessary to perform steps 5- 6 if your printer does not feature in
the model list.
5. Click the Have Disk... button. Insert the printer driver diskette/CD into the
appropriate disk drive of your computer.
6. Select the type of printer you want to install from the diskette/CD and click
Next. If you already have the printer’s driver installed, you will be asked
whether to keep it or to replace it.
7. Select the Printers@TCP/IP Port and click Next.
8. Enter an appropriate name for your printer and choose whether you want
it to be the default printer. Click Next.
9. In the next window, do not order a Test Page to be written, just click Finish.
10. The printer you have defined will now be displayed in the Printers Folder.
Right-click the printer object and select Properties.
11. Click the Details tab within the Properties page and then click Add Port to
display the available monitors.
12. Click the radio button “other”. Select AXIS Port and then click OK.
13. Select LPR (TCP/IP) as your choice of protocol and click OK.
14. Enter the IP address or the host name of your print server (Example IP
address: 192.168.3.191 or host name: AXIS181636).
In the Logical Printer Name field, enter the port you wish to use; USB1,
LPT1, LPT2 or COM1.
15. The TCP/IP port will then be added automatically to the list of available ports.
Click Apply and OK.
16. You may now configure the port, as described below. The Axis Printer Port
is now installed.
AXIS 5570e / AXIS 5670e User’s Manual
79
Adding Printers in Windows
Configure the Port:
1. Select Settings | Printers from the Start menu and highlight the printer
you wish to configure. Select File | Properties | Details and click Port
Settings.
2. Choose whether error condition pop-up messages are to be displayed by
checking the box in the Configure AXIS Ports dialog. Define the frequency
at which the error messages should be displayed after retry. Click OK.
Even if the desired printer is available in the Manufacturers and Printers lists, you are advised
to use the print driver provided with the printer. This assures you of the latest driver software.
80
AXIS 5570e / AXIS 5670e User’s Manual
Adding Printers in Windows
Adding Printers in Windows 98 and Me over NetBIOS/NetBEUI using AXIS Print Monitor
Follow the procedures below to install Axis NetBIOS/NetBEUI printer
ports on a Windows 98 workstation, using AXIS Print Monitor:
1. To start the Add Printer Wizard, select Settings | Printers from the Start
menu and double-click the Add Printer icon.
2. After clicking Next in the first dialog, the Wizard asks you to select Local
printer or Network printer. Select Local printer. Click Next.
3. Choose the appropriate printer driver for your printer. If the desired printer
driver appears in the displayed Manufacturers and Printers lists, highlight
your selection, click Next and proceed directly to step 6. It is only necessary
to perform steps 4 - 5 if your printer does not appear in the model list.
Note:
Even if the desired printer is available in the Manufacturers and Printers lists, you are
advised to use the printer driver provided with the printer. This assures you of the latest driver
software.
4. Click the Have Disk... button. Insert the printer driver diskette/CD that was
provided with your printer, select the appropriate diskette/CD drive and click
OK.
5. Select the printer driver you want to install and click Next.
6. Select the AXIS Printer Port from the Available Ports list. The port names
appears as <name>.<port>. Here, <name> is AX followed by the last six
digits of the print server’s serial number (e.g. AX100086) and <port> is taken
from the table below. Click the Configure Port button.
Ports available
USB port
Parallel port 1 Parallel port 2
Serial port
AXIS 5570e
US1
LP1
—
—
AXIS 5670e
—
LP1
LP2
CM1
Example: AX100086.LP1
7. Choose whether error condition pop-up messages are to be displayed by
checking the box in the Configure AXIS Ports dialog. Define the frequency
at which the error messages should be displayed after retry. Click OK and
Next.
8. Enter an appropriate name for your printer and click Next.
9. Choose whether you wish to print a test page and click Finish.
AXIS 5570e / AXIS 5670e User’s Manual
81
Adding Printers in Macintosh
Section 7
Adding Printers in Macintosh
Having connected the AXIS 5570e/AXIS 5670e to your network, this
section now describes how to set up your print server for printing in Mac
OS X and earlier Macintosh environments using AppleTalk.
If you intend to use the print server in a multi-protocol environment,
refer to the chapters pertaining to the respective operating systems in this
manual.
Bonjour Printing in Mac OS X
Bonjour is available from Mac OS X 10.2 and up. Bonjour is enabled by
default in the print server. You can alter the Bonjour parameters from the
print server’s Web interface: select Admin | Network Settings | Detailed
View | TCP/IP Network.
1. From the Apple menu, select Go | Applications | Utilities and start the
Print Center or the Printer Setup Utility.
2. Click Add in the Printer List.
3. From the drop-down list, select Bonjour.
4. High-light the printer you want to install. The print server’s default name
is AXISxxxxxx Network Print Server (where the xs represent the last six
digits of the print server’s serial number) followed by the ports available.
Example: AXIS610282 Network Print Server_USB1.
5. Select printer manufacturer and model from the drop-down list. (For some
printer drivers, Printer Manufacturer and Model are selected automatically.)
82
AXIS 5570e / AXIS 5670e User’s Manual
Adding Printers in Macintosh
6. Click Add to finish the installation. The print server has now been added to
the Printer List.
7. If you wish to configure printer settings, click Printers | Configure Printer.
To Change the
Bonjour Service Name
You can change the print server’s Bonjour service name via the print server’s
Web interface: Admin | Network Settings | Detailed View | TCP/IP Network
=> Bonjour Service Name.
If the print server using Bonjour is already installed and the print server
name or service name is changed, the print server must be removed from
the Printer List and then re-installed with the new Bonjour service name.
AXIS 5570e / AXIS 5670e User’s Manual
83
Adding Printers in Macintosh
Installation in Mac OS X using AppleTalk
This section describes setting up your print server for printing in the Mac
OS X.
1. Start Print Center (from Go | Applications | Utilities | Print Center)
2. Select Printers | Add Printer...
3. From the Printer List dialog, select AppleTalk.
4. Now, the ports of your print server will appear in the list of available printers.
The port is shown as <host name>_<port>.
Example: AXIS100086_LPT1.
5. Select the print server port you want to use.
6. Select an appropriate printer driver for your printer from the Printer Model
drop-down list. If the printer is not available in the list, select Generic.
(Note: Generic is only used for postscript printers.)
You can also browse for a printer driver on your computer or network by
selecting Other... from the list.
7. Click Add to complete the installation.
Installation of LPR printing in MAC OS X
If you want to print using LPR, select:
1. Printers | Add Printer...
2. From the Printer List dialog, select LPR printers using IP.
3. Enter the IP address or host name of the print server in the LPR printer’s
Address field. You must uncheck the Use Default Queue on Server check
box and enter a Queue Name:
Ports available
USB port
Parallel port 1 Parallel port 2
Serial port
AXIS 5570e
USB1
LPT1
—
—
AXIS 5670e
—
LPT1
LPT2
COM1
Choose a printer driver from the Printer Model list and click Add to finish.
84
AXIS 5570e / AXIS 5670e User’s Manual
Adding Printers in Macintosh
Installation on Mac OS 9.1 or older, using AppleTalk
Basic Configuration
On Mac OS 9.1 or older, basic configuration in AppleTalk is performed
simply by opening the Chooser window and selecting a printer.
You can change the default name of your print server or any of default
parameters by editing the print server’s config file. To access the config
file from a Macintosh, you can use:
• any Web browser with Javascript enabled
• FTP using MacTCP, Fetch or Anarchie
In order to use any of these methods, you must assign an IP address to the
print server as described in “Setting Parameters” on page 87.
Choosing a Printer
Selecting a Printer
The method for choosing a printer varies depending on which version of
LaserWriter printer driver you are using.
•
•
Autodetect Printer
Type
The LaserWriter 7.0 driver assumes that you use a standard PostScript
driver, and cannot take advantage of any printer specific features.
The LaserWriter 8.0 driver uses PPD files that contain printer
descriptions. This gives you full control over any features your printer
might have.
The print server can automatically detect the type of printer you are using
if you enable Autodetect Printer Type. The print server can then
recognize Epson and Hewlett Packard InkJet printers. Most Epson and
Hewlett Packard InkJet printers that have Mac OS printer drivers for
network printing are supported. Without the Autodetect Printer Type
function, the AppleTalk printer type has to be specified manually in the
print server. For Epson InkJets it would be "EPSONLQ2" and for HP
InkJets it would be "DeskWriter". If the print server does not recognize
the connected printer, the default setting "LaserWriter" will be used as
printer type. "LaserWriter" is the recommended setting to be used with all
PostScript printers.
To enable Autodetect Printer Type, log in to your print server’s Web
interface and select Admin | Network Settings | Detailed View |
Macintosh | Auto Detect Printer Type | Yes.
See the Help pages in the print server’s Web interface for details.
LaserWriter 7.0 Printer
Driver
Follow the instructions below to choose a printer:
1. Select Chooser from the Apple menu.
2. Click the LaserWriter icon.
3. If your network has more than one zone, click on the zone you want. (If your
network does not have any zones, this box will not appear.)
AXIS 5570e / AXIS 5670e User’s Manual
85
Adding Printers in Macintosh
4. Click the name of the printer you want — the ports are shown as <host
name>_<port>. Example: AXIS100086_USB1.
5. Click the Close box. This completes the configuration and closes the
Chooser.
Repeat this procedure for each Macintosh computer on the network using
the print server.
LaserWriter 8.0
Printer Driver
Follow the instructions below to choose a printer:
1. Select Chooser from the Apple menu.
2. Click the LaserWriter 8.0 icon.
3. If your network has more than one zone click on the zone you want. (If your
network does not have any zones, this box will not appear.)
4. Click the name of the printer you want — the ports are shown as <host
name>_<port>. Example: AXIS100086_USB1.
5. Click Setup... and then Auto Setup. If the selected printer supports bidirectional printing and the appropriate PPD file is available, the installation
is performed automatically and you can therefore proceed directly to step
7 (if this is not the case, the PPD file must be selected manually, as described
in step 6).
6. Choose the PPD file matching your printer, and click OK.
If your printer does not appear in the PPD file list, please contact your printer
vendor. Use the Generic PPD if you do not need any printer specific features.
7. Click OK, and then click the Close box. This completes the configuration and
closes the Chooser.
Repeat this procedure for each Macintosh computer on the network using
the print server.
Bi-directional
Support
The AXIS 5570e/AXIS 5670e allow the printer driver to communicate
directly with the printer and consequently facilitates complete functional
control over print jobs, e.g. automatic downloading of fonts not resident
in the printer.
This functionality has backward compatibility with older printers and
Macintosh computers, which means that the AXIS 5570e/AXIS 5670e can
generate appropriate responses to Macintosh printer queries when the
connected printer does not support bi-directional communication.
86
Verifying the Setup
You simply need to print a document from the Macintosh computer to
verify communication to the chosen printer. The basic installation can be
considered complete if the print test is satisfactory. The AXIS 5570e/AXIS
5670e is now ready for use.
BCP and TBCP
You should specify if you want to enable or disable binary transfer of
print data in the print server’s Web interface (Admin | Network Settings
AXIS 5570e / AXIS 5670e User’s Manual
Adding Printers in Macintosh
| Detailed View | Macintosh | Binary Protocol for Printer n. By enabling
binary transfer you reduce printing time, provided that the print job is
sent as binary data to the print server. This is particular true when you are
printing large bitmaps.
•
•
•
TBCP enables the print server to use the TBCP (Tagged Binary
Communication Protocol) to transfer print data to the printer. Select
this alternative when using Postscript printers.
BCP enables the print server to use the BCP (Binary Communications
Protocol) to transfer print data to the printer. Select this alternative
when using Postscript printers.
None disables all binary transfers, select this alternative for all nonPostScript printers and for ASCII PostScript printing.
Notes:
• If you have have set the Autodetect Printer Type parameter to YES, the text output format
will be chosen automatically (Admin | Network Settings | Detailed View | Macintosh | Auto
Detect Printer n Type | Yes).
• Some printers, e.g. Epson InkJet printers, can not be used when TBCP is enabled.
Setting Parameters
In AppleTalk, you can change a limited number of the parameters of the
AXIS 5570e/AXIS 5670e. You can:
• enable and disable binary data transfers for your printing
• select the type of binary transfer protocol to use
• specify the AppleTalk printer type
• set the IP address
However, by assigning an IP address to your print server, you have access
to all of the print server parameters via any standard Web browser or via
FTP. Refer to “Management and Configuration” on page 128 for more
information.
Example:
The following example describes how you set the print server parameters
in AppleTalk.
Important:
DO NOT use the parameter values from this example when configuring your print server. You
should select values that are appropriate for your printers and network settings.
Follow the instructions below:
1. Open the Chooser from the Apple menu.
2. Select a network printer driver — any LaserWriter will do.
3. Select the printer port ending with _CFG.
4. Close the Chooser.
5. Open a text editor, e.g. SimpleText.
AXIS 5570e / AXIS 5670e User’s Manual
87
Adding Printers in Macintosh
6. Write a text file containing the parameters you want to set:
BINARY_TYPE_1.
INT_ADDR.
ATYPE_1.
:BCP
:192.168.3.191
:EPSONLQ2
Note:
Parameters that you do not want to set should be excluded from the text file. Refer to the
Parameter list in this manual for information about which values that are valid for each
parameter.
7. Print the text file. The settings will be stored in the print server.
8. Open the Chooser and select the printer port you wish to use for printing
documents.
9. Close the Chooser.
Note:
The _CFG port disappears 60 minutes after the AXIS 5570e/AXIS 5670e has been powered on.
If you want it to reappear, you must restart your print server.
88
AXIS 5570e / AXIS 5670e User’s Manual
Adding Printers in NetWare
Section 8
Adding Printers in NetWare
This section describes how to continue the installation of the AXIS
5570e/AXIS 5670e in the NetWare environment. Identify which transport
protocol you are running on your network and which installation method
you should use. Continue the installation by selecting the appropriate
installing instructions from the table below:
Installation
method
Transport protocol
Action
NDPS
TCP/IP
IPX/SPX
See “Setup using NDPS” on page 89 and
“Public Access Printers” on page 90
“Controlled Access Printers” on page 94
iPrint over LPR
See “Setup using iPrint” on page 103 and
“Install a printer using AXIS LPR Gateway Configuration
Snap-in” on page 106
iPrint over IPP
See “Setup using iPrint” on page 103 and
“Install a printer with AXIS IPP Gateway Configuration
Snap-in” on page 105
IPX/SPX
Basic Configuration
To install using the AXIS NetPilot Installation Wizard,
see “Basic Setup with AXIS NetPilot” on page 108
IPX/SPX
Advanced
configuration
If you need a more advanced installation that is not
covered by the AXIS NetPilot Installation Wizard, see
“Advanced Installation using AXIS NetPilot” on page
110
iPrint
Queue-based
printing
See “NetWare Administration” on page 114. for information on Novell’s
administration tools.
If you intend to operate your AXIS 5570e/AXIS 5670e in a multiprotocol, mixed environment, you should also proceed to the other
relevant sections in this manual.
Setup using NDPS
The AXIS 5570e/AXIS 5670e supports Novell Distributed Print Services
(NDPS). You can run NDPS over Pure IP (TCP/IP) or IPX/SPX.
Before the AXIS 5570e/AXIS 5670e can be installed, make sure that
NDPS is installed and a Broker is loaded on your NetWare file server.
Axis Network Print Server uses the AXIS NDPS Gateway for printing in
networks using either IP or IPX as transport protocols. The printer
gateways are included with the NDPS software (from version 5.1 and up)
and are automatically installed together with NDPS.
Installing the Axis
Network Print Server
in the NDPS
environments
Having assigned an IP address to the AXIS 5570e/AXIS 5670e as
described in Setting the IP Address, on page 16, you are now ready to
install the Axis Network Print Server for NDPS printing. You can select to
install the connected printers as public or controlled access printers.
Follow the instructions below to install the Axis Network Print Server
using NDPS:
AXIS 5570e / AXIS 5670e User’s Manual
89
Adding Printers in NetWare
Important:
Public Access Printers
•
The NDPS Enabled parameter of the Axis Network Print Server is by default enabled. It must
be set to Yes in order for the communication between the print server and the NDPS gateway
to be enabled. To change this parameter, log in to the print server’s Web pages and choose:
Admin | Network Settings | Detailed View | NetWare=> NDPS Enabled => Yes.
•
If you do not have an NDPS Manager object available, start out with creating one in the NetWare Administrator.
Follow these instructions to create a public access printer using the NDPS
Manager object in your NetWare administrator utility:
1. Double-click on the NDPS Manager object you will be using to control
the Printer Agents.
2. On the Identification page for the NDPS Manager, click the printer Agent
List button. The Printer Agent List dialog will appear.
3. Click New. The Create Printer Agent dialog will appear.
4. Type a name of your choice in the NDPS Printer Agent field:
5. Select the Axis Gateway configuration in the Gateway Type window.
6. Click OK
7. In the Select the printer’s type window, choose your printer. If you cannot
find the printer, select an appropriate Generic one (PCL, PS, etc)
8. Select TCP/IP (default) or IPX as network protocol. Click Next.
90
AXIS 5570e / AXIS 5670e User’s Manual
Adding Printers in NetWare
9. You will find the print server in the next window with the printer attached
on the connected port. Depending on the transport protocol you used when
you start the installation, the print server should appear as following:
•
TCP/IP Network protocol:
IP Address and Port, e.g: 192.168.70.243 and LPT1
1. Only the ports with a connected printer show up in this window. If the
printer is not in the displayed print list, click Manually specify the print
server and do the following:
Enter the print server’s IP address in the IP Address Field
2. Choose a port in the Print Server Port field
e.g., 192.168.70.243 and LPT1
The available ports are :
Ports available
USB port
Parallel port 1 Parallel port 2
Serial port
AXIS 5570e
other/unknown
LPT1
—
—
AXIS 5670e
—
LPT1
LPT2
COM1
Note: “other/unknown”, stands for the USB1 port.
AXIS 5570e / AXIS 5670e User’s Manual
91
Adding Printers in NetWare
IPX Network protocol:
All the available ports will be presented, regardless if the printers are
or not connected to those ports, e.g.
LPT1
AXIS5FF66A_P1
LPT2
AXIS5FF66A_P2
USB1
AXIS5FF66A_P2
COM1
AXIS5FF66A_P3
The IPX Addresses for the above printers will appear as:
<IPX External Network Number>:<Print server’s HW
address>:<Socket Number>
i.e.: 01d7e1c2:00408c5ff6a6:400c
where 400c, 401c, and 402c are the socket numbers corresponding to
the LPT1, LPT2, USB1 and COM1 physical ports:
92
LPT1
400c
LPT2
401c
USB1
401c
COM1
402c
AXIS 5570e / AXIS 5670e User’s Manual
Adding Printers in NetWare
If the printer is not in the displayed print list, click Manually specify
the print server and do the following:
1. Enter the <IPX External Network Number> in the Network field.
2. Enter the <Print server’s HW address> in the LAN HW address field.
3. Choose a port in the Print Server Port field, e.g. 01d7e1c2:00408c5ff6a6
and LPT1
Ports available
USB port
Parallel port 1 Parallel port 2
Serial port
AXIS 5570e
other/unknown
LPT1
—
—
AXIS 5670e
—
LPT1
LPT2
COM1
Note: other/unknown, stands for the USB1 port.
4. When done, select your printer and click Finish.
AXIS 5570e / AXIS 5670e User’s Manual
93
Adding Printers in NetWare
5. Next, select the printer drivers for each client operating system. (Windows
2000, NT and 95/98). These drivers will be automatically downloaded to
users’ workstations when they install this printer in the future.
6. Click Continue and OK in the next NDPS window. The new Printer Agent
appears in the Printer Agent List window.
Check the Status: it should be Idle.
7. Press Cancel to close the NDPS Manager
To install the printer on the workstation, See “Installing an NDPS Printer
on the Workstation” on page 100.
Controlled Access
Printers
Follow these steps to create a controlled access printer as an object in the
Directory Tree, using the NetWare administrator utility:
1. Log in as Admin.
2. Start the NW Admin utility on any Workstation
(SYS:PUBLIC\WIN32\nwadmin32.exe).
3. Browse the context your NDPS Manager resides in.
94
AXIS 5570e / AXIS 5670e User’s Manual
Adding Printers in NetWare
4. From the Object menu, select Create. The New Object dialog appears.
5. Select NDPS Printer. The Create NDPS Printer dialog appears.
6. Type a name of your choice in the NDPS Printer Name field, e.g.
AXIS5FF66A_IPX1
In the Printer Agent Source field, select the source of the Printer Agent. The
following options are available:
- Create a New Printer Agent. If you select this option, you are asked to
select either the Novell Gateway or a third party Gateway.
- Printer Agent on Existing NDS Object. Use a Printer already configured
as a controlled access printer (NDPS Printer Object).
If you select this option, a list of current NDPS Printer Objects in this
container will be displayed from which you can select the one you want to
use.
- Public Access Printer Agent. Use an existing Printer Agent representing
a Public Access Printer.
7. Select Create a New Printer Agent and click Create to display the Create
Printer Agent dialog.
AXIS 5570e / AXIS 5670e User’s Manual
95
Adding Printers in NetWare
8. Confirm the Printer Agent name (default is the name of the new printer you
are creating) and browse to select the NDPS Manager to which you want
to assign it
9. Select AXIS Gateway Configuration in the Gateway Type field.
10. Click OK.
11. In the Select the printer’s type window choose your printer. If you cannot
find the printer, select an appropriate Generic one (PCL, PS, etc)
12. Select TCP/IP (default) or IPX as network protocol.
13. Click Next.
14. You will find the print server in the next window with the printer attached
on the connected port.
Depending on the transport protocol you used when you start the
installation, the print server will appear as:
96
AXIS 5570e / AXIS 5670e User’s Manual
Adding Printers in NetWare
•
TCP/IP Network protocol:
IP Address and Port, e.g.
192.168.70.243 and LPT1
Only the ports with a connected printer will show up in this window.
If the printer is not in the displayed print list:
1. Click Manually specify the print server enter the print server’s IP address
in the IP Address Field.
2. Choose a port in the Print Server Port field e.g., 192.168.70.243 and LPT1:
Ports available
USB port
Parallel port 1 Parallel port 2
Serial port
AXIS 5570e
other/unknown
LPT1
—
—
AXIS 5670e
—
LPT1
LPT2
COM1
Note: other/unknown stands for the USB1 port.
AXIS 5570e / AXIS 5670e User’s Manual
97
Adding Printers in NetWare
IPX Network protocol:
All the available ports will be presented, regardless if the printers are
or not connected to those ports,.
LPT1
AXIS5FF66A_P1
LPT2
AXIS5FF66A_P2
USB1
AXIS5FF66A_P2
COM1
AXIS5FF66A_P3
The IPX Addresses for the above printers will appear as:
<IPX External Network Number>:<Print server’s HW
address>:<Socket Number>
i.e.: 01d7e1c2:00408c5ff6a6:400c
where 400c, 401c, and 402c are the socket numbers corresponding to
the LPT1, LPT2, USB1 and COM1 physical ports:
LPT1
400c
LPT2
401c
USB1
401c
COM1
402c
If the printer is not in the displayed print list:
1. Click Manually specify the print server and enter the <IPX External
Network Number> in the Network field.
2. Enter the <Print server’s HW address> in the LAN HW address field.
98
AXIS 5570e / AXIS 5670e User’s Manual
Adding Printers in NetWare
3. Choose a port in the Print Server Port field:
e.g.: 01d7e1c2:00408c5ff6a6 and LPT1.
Ports available
USB port
Parallel port 1 Parallel port 2
Serial port
AXIS 5570e
other/unknown
LPT1
—
—
AXIS 5670e
—
LPT1
LPT2
COM1
Note: other/unknown stands for the USB1 port.
4. When done, select your printer and click Finish.
5. Next, select the printer drivers for each client operating system. (Windows
2000, NT and 95/98). These drivers will be automatically downloaded to
users’ workstations when they install this printer in the future.
6. Click Continue and OK in the next NDPS window. Your printer will appear
as an NDS object in the Directory Tree and will offer a full range of network
security options.
AXIS 5570e / AXIS 5670e User’s Manual
99
Adding Printers in NetWare
To install the printer on the workstation, See “Installing an NDPS Printer
on the Workstation” on page 100.
Installing an NDPS
Printer on the
Workstation
Using Novell Printer
Manager
To install the printer on a workstation, use either Novell Printer Manager
(NetWare 5.1 only) or the Add Printer Wizard on the local workstation.
1. Log in as Admin.
2. On the any workstation, browse to
<NW 5.1 File Server>\SYS:PUBLIC\Win32
and start Nwpmw32.exe (Novell Printer Manager).
The Novell Printers dialog appears, displaying a list of installed Public or
Controlled printers (if any printers have previously been installed on the
workstation).
3. From the Printer Manager’s Printer pull down menu, select New.
4. Click Add. A list of available printers appears.
100
AXIS 5570e / AXIS 5670e User’s Manual
Adding Printers in NetWare
5. The list of available printers shows the NDPS Public Access Printers on the
network and the NDPS Controlled Access Printers in you current NDS
context. To see the Controlled Access Printers in other context that you have
rights to, click the Browse button and select your choice. Click OK.
6. Once selected, click Install. The Novell Printers – Install dialog appears.
7. Click OK. The default driver for that printer is then automatically
downloaded.
If the printer object does not have a printer driver associated with it, or a
driver was not found, you will be prompted to either to choose from a list
of printer drivers provided by NDPS or to provide a disk with the appropriate
driver.
The Novell Printers dialog appears with the new printer, e.g.
AXIS5FF6A6_IPX1 in the installed list.
8. Click Close.
In the Novell Printer Manager window the new installed NDPS printer
appears with the name e.g. AXIS5FF6A6_IPX1 and is available for print jobs.
AXIS 5570e / AXIS 5670e User’s Manual
101
Adding Printers in NetWare
9. Verify by clicking Start - Settings - Printers on the workstation.
Using the Add Printer
Wizard
1. Click Start on your workstation, select Settings =>Printers. There might
be some differences regarding this menu depending of MS Operating
System you are running.
2. Start the Add Printer Wizard on the workstation. The Add Printer Wizard
dialog will appear. Click Next.
3. Select Network printer and click Next.
4. Click Next again in the Locate Your Printer dialog (Win2000/XP) or press
the Browse button (Win9X)
102
AXIS 5570e / AXIS 5670e User’s Manual
Adding Printers in NetWare
5. Browse to the NDPS Printers. Expand either the NDPS Controlled Access
Printers or the NDPS Public Access Printers folder, select your newly
installed NDPS printer and follow the instructions.
When you have completed these steps, you are ready to start printing.
Notes:
• The Public Access print servers are immediately available for everyone on the network
• The Axis Gateway Configuration Utility is an installation and configuration tool for NDPS
printers in the NetWare environment.
The Axis Gateway will appear in NetWare 5.1 and later releases. You can download the Axis
Gateway Configuration Utility for use with earlier versions of NetWare from www.axis.com.
• To print using TCP/IP, Axis print server firmware 6.1 or later is required. In order to print
using IPX/SPX, Axis print server firmware 5.51 or later is needed.
Setup using iPrint
iPrint is Novell's next generation of printing software that lets users print
to and from all destinations.
A standard Web page displays available printers to the user.
By clicking a printer, the iPrint client is installed (if not installed
previously), the printer's driver is downloaded, and a printer is created in
the user's Printer folder, enabling the user to send documents to the
printer from any application on the desktop.
Before setting up iPrint printers, make sure that you meet all the iPrint
Setup requirements. See the Novell iPrint Administration Guide for
instructions on installing, configuring, and customizing iPrint.
AXIS Print servers can be installed as iPrint printers, either by using the
Novell LPR gateway (LPR on IP) or the AXIS Gateway Configuration
Snap-in for iPrint.
Axis provides two Snap-ins for iPrint:
•
•
AXIS LPR Gateway Configuration
AXIS IPP Gateway Configuration
AXIS 5570e / AXIS 5670e User’s Manual
103
Adding Printers in NetWare
When you install Service Pack 6 (16 April 2003) for NetWare 5.1 or later
and Service Pack 3 (16 April 2003) for NetWare 6.0 or later, the AXIS LPR
Gateway Configuration will automatically be installed and configured on
the NetWare Servers and ready for use.
The AXIS IPP Gateway Configuration Snap-in for NetWare 6.0 can be
downloaded for free from www.axis.com. Follow the instructions below
to install the AXIS IPP Gateway Configuration Snap-in for NetWare 6.0,
if you want to add it in your iPrint environment.
Installing AXIS IPP
Gateway
Configuration Snapin for NetWare 6.0
1. Download the free axisIPP-snap-in.zip file from www.axis.com and unzip
it in a temporary directory.
2. Make sure the the NetWare Enterprise Web Server was previously installed
on the server. Otherwise, install it.
3. Novell iPrint uses the NDPS infrastructure, so make sure that all the NDPS
requirements have been met:
• Make sure that the BROKER.NLM is loaded. If it is not, type LOAD
BROKER in the server console prompt and select the name of the
Broker.
• Make sure that the NDPS Manager object is created in the Novell
Directory Services (NDS) tree. Refer to your Novell documentation
for creating this object.
• Make sure that the NDPSM.NLM is loaded. If it is not, type LOAD
NDPSM in the server console prompt and select the appropriate
NDPS Manager.
4. Shutdown Tomcat and the NetWare Enterprise Web Server on the NetWare
file server by executing the following commands:
Type "NSWEBDN" <Enter>
Type "TOMCAT33 -STOP" <Enter>
Type "NVXADMDN" <Enter>
5. Map the next available drive (e.g. G:) to the root of volume SYS on your
NetWare server.
From the temporary directory where axisIPP-snap-in.zip has been
unzipped, run the batch file AxisIPP.bat (default G:).
If the drive G: is not available, you have to edit the batch file and change
the drive to next available one.
Check that each line in the batch file is executed without failure.
6. Restart Tomcat and the NetWare Enterprise Web Server on the file server
by executing the following commands:
Type "TOMCAT33" <Enter>
Type "NVXADMUP" <Enter>
Type "NSWEB" <Enter.
104
AXIS 5570e / AXIS 5670e User’s Manual
Adding Printers in NetWare
7. Access the iManager Web page on the NetWare server by opening the
following URL:
https://<IP address of NW server>:2200/eMFrame/iManager.html
You have to authenticate.
8. Click on iPrint Management on the left pane and select Create Printer.
9. On the right pane, verify that the newly installed AXIS IPP Gateway
Configuration is under the Gateway type drop-down menu.
If not, it may be necessary to restart the NetWare server.
Now you are ready to use the AXIS IPP Gateway Configuration for installing
iPrint printers. You have to have Administrator rights to install the printers
through iPrint.
Install a printer with
AXIS IPP Gateway
Configuration Snapin
1. Use an AXIS 5570e/AXIS 5670e and connect a printer to whatever port
you want.
2. Connect the print server to the network.
3. Connect the Power Adapter.
4. Start the printer and the print server.
5. Log in as Admin.
6. Use a Web browser and the local host URL to login into iManager on your
NetWare server.
7. Open your browser to the following URL:
https://<IP address of NW server>:2200/eMFrame/iManager.html
You have to authenticate.
8. Click on iPrint Management on the left pane.
9. Click on Create Printer.
10. Choose a name of your choice for the printer
11. Choose the context where the printer will be installed.
12. Browse for the NDPS Manager and select it.
13. In the Gateway Type drop-down list, choose the Axis IPP Gateway
Configuration. Press Next.
14. In the Printer URL, you may choose either the IPP version 1.0 format:
http://<IP address of your print server>:631/lptx
or the IPP version 1.1:
ipp://<IP address of your print server>/lptx
where x is the port number. Click Next.
15. Select default drivers for your printer. Click Next and OK.
AXIS 5570e / AXIS 5670e User’s Manual
105
Adding Printers in NetWare
Install a printer using
AXIS LPR Gateway
Configuration Snapin
1. Use an AXIS 5570e/AXIS 5670e and connect a printer to whatever port
you want.
2. Connect the print server to the network.
3. Connect the Power Adapter.
4. Start both the printers and the print server.
5. Log in as Admin.
6. Use a Web browser and the local host URL to login into iManager on your
NetWare server.
7. Open your browser to the following URL:
https://<IP address of NW server>:2200/eMFrame/iManager.html You have
to authenticate.
8. Click on iPrint Management on the left pane.
9. Click on Create Printer.
10. Choose a name for the printer.
11. Choose the context where the printer will be installed.
12. Browse for the NDPS Manager and select it.
13. In the Gateway Type drop-down list, choose the Axis LPR Gateway
Configuration. Click Next.
14. Choose either the IP address or the DNS Name for your print server.
15. Under Printer name, select the physical printer port, e.g. LPT1, or logical
printer port pr1-pr8 using the drop-down list. Click Next.
16. Select default drivers for your printer. Click Next and OK.
Installing the iPrint
Printer on the
Workstation
An iPrint printer can by locally installed on the workstation in two ways:
Installing the iPrint
Printer using the
iPrint Client.
In order for users to use iPrint, they need to install the Novell® iPrint
Client software and a printer. When a user selects a printer to be installed
by iPrint, iPrint checks to see if the Novell iPrint Client software is
installed and then installs it if necessary. Then the printer driver is
downloaded and the printer is installed in the user's Printer folder.
•
•
Using the iPrint Client
Using the MS Add Printer Wizard at the workstation.
See “Using the Add Printer Wizard” on page 102.)
In order for iPrint to work properly, the workstation should have the
following:
•
•
106
Windows 95/98/Me or Windows NT*/2000/XP
Web browser with JavaScript enabled:
• Microsoft Internet Explorer 5.0 or later
• Netscape 4.76 (iPrint is not supported on Netscape 6)
AXIS 5570e / AXIS 5670e User’s Manual
Adding Printers in NetWare
The user should use the following iPrint url:
http://<IP address of your NW server>:631/IPP
1. From a Netscape or Internet Explorer browser, enter the provided URL.
A Web page displays a listing of available printers to install and a link to
install the client software.
2. Select Install iPrint client software to locally install the iPrint printers. If
you try to install a printer before installing the iPrint client software, you
will be prompted to install the client software first.
If you associate a printer driver with a printer being installed, the driver is
automatically installed on the user's workstation. If the driver already exists,
that driver is overwritten even if it is a newer driver.
3. After installing a printer, it is added to the user's Printer folder. Users can
print to the printer by selecting it from any application.
AXIS 5570e / AXIS 5670e User’s Manual
107
Adding Printers in NetWare
Basic Setup with AXIS NetPilot
Install the AXIS NetPilot software on your computer. AXIS NetPilot runs
on Windows 98 and Windows NT.
Starting the
Installation
Follow the instructions below to install the AXIS 5570e/AXIS 5670e with
AXIS NetPilot:
1. Start AXIS NetPilot by double-clicking the NetPilot icon, which is located
in the folder where you installed AXIS NetPilot.
2. Locate the Axis Network Print Server in the ‘New Axis Units’ folder. Select
it and click the Install button on the AXIS NetPilot toolbar. If your network
is large, it could take a few seconds before the print server appears in the
folder.
3. Choose the with Installation Wizard option.
The AXIS NetPilot Installation Wizard guides you through the installation
process. The following options are available:
Note:
The number of options varies according to the number of environments you enable.
Print Server Name
108
The default print server name consists of the characters ‘AXIS’ followed
by the last six digits of the serial number. If you want to change the print
server name, just type the new name in the available text field.
Environments
Choose which networking environments you want to configure the Axis
Network Print Server for, e.g. NetWare, TCP/IP, Windows & OS/2 or
Macintosh. If your network comprises various different platforms, you
can enable any combination of environments.
NetWare NDS
Place NetWare Print Queues on a specific bindery server, or alternatively
into an NDS Tree.
The IP Address
Choose the method the Axis Network Print Server should employ for
obtaining an IP address. DHCP, arp, RARP, BOOTP and Auto-IP are
supported. You can also select to set the IP address manually. Refer to
“Setting the IP Address” on page 16 for further information about setting
the IP address.
Print Queues
The Axis Network Print Server uses the print server name followed by the
printer port as the default Print Queue names and print server port names.
If you want to change the default printer queue names, just type the new
names in the available text fields.
AXIS 5570e / AXIS 5670e User’s Manual
Adding Printers in NetWare
AXIS 5570e
Environment
NetWare
Windows & OS/2
AppleTalk
Default Names
AXIS1A0003_USB1_Q
AXIS1A0003_LPT1_Q
AX1A0003.US1
AX1A0003.LP1
AXIS1A0003_USB1
AXIS1A0003_LPT1
Default Print Queue Names and Print Server Port Names
for each of the operating environments.
AXIS 5670e
Environment
Default Names
AXIS1A0003_LPT1_Q
NetWare
AXIS1A0003_LPT2_Q
AXIS1A0003_COM1_Q
AX1A0003.LP1
Windows & OS/2
AX1A0003.LP2
AX1A0003.CM1
AXIS1A0003_LPT1
AppleTalk
AXIS1A0003_LPT2
AXIS1A0003_COM1
Default Print Queue Names and Print Server Port Names
for each operating environment.
Test Page
The final user prompt in the Installation Wizard allows you to print a test
page through NetWare. The test page displays the name of all the
NetWare servers the Axis Network Print Server is connected to and shows
the status of each connection.
Unless you want to connect or create additional printing queues, the
installation for the NetWare environment is now completed.
Notes:
•
The parameters entered during installation are not permanent; they can be altered at any
time according to your network printing requirements.
•
No serious or permanent damage will be caused if you make a mistake during installation.
If you find, at any time, that printing is not satisfactory, the parameters can easily be
changed to tune the system to your requirements.
•
For information on advanced functions, please refer to the AXIS Network Print Server Technical Reference. You can download this or other technical information over the Internet by
accessing www.axis.com
AXIS 5570e / AXIS 5670e User’s Manual
109
Adding Printers in NetWare
Advanced Installation using AXIS NetPilot
Having installed your Axis Network Print Server print server in
accordance with the basic installation procedures described in Basic
Setup with AXIS NetPilot, on page 108, your Axis Network Print Server
print server should now feature in the ‘Network Print Servers’ folder
located in the AXIS NetPilot main window.
NetWare Network
Environment Window
The NetWare Network Environment window allows you to connect
additional print queues to your Axis Network Print Server as well as
create new ones.
Follow the steps below to gain access to the NetWare Network
Environment window:
1. Select the required Network print server from the ‘Network Print Server’
folder.
2. Choose Network from the Setup menu or click on the Network icon on the
AXIS NetPilot’s toolbar.
3. If you are not logged on to your NetWare file server, a dialog box will
ask you to log on.
The Axis Network Print Server periodically updates the configuration by
scanning the NDS tree or, in the case of NetWare versions 3.x, the
designated file servers.
Connecting
Print Queues
Follow the steps below to connect a print queue to the print server port:
1. Open the NetWare ’Network Environments’ window.
2. Select the print server port you want to connect.
3. Click the Connect... button.
The Connect NetWare Print Queues window appears.
110
AXIS 5570e / AXIS 5670e User’s Manual
Adding Printers in NetWare
4. Select the tree or server location of the print queue from the Resources box.
5. Select an existing print queue to connect to the server port, or create a new
print queue by clicking on Create Queue... If you have selected an existing
queue, advance to step 8. Continue with step 6 only if you want to create
a new queue.
6. Type the queue name in the Create Queue dialog window. If you want to
create a queue in the NDS tree you must also enter the name of the volume
where the queue will be located. Click OK.
7. Select the newly created queue from the queue list.
8. Select Print Server Mode or Remote Printer Mode. If you selected Print
Server Mode, advance directly to step 11, otherwise continue with step 9.
9. Select an appropriate NetWare Print Server name, that will be associated
with the Axis Network Print Server, by using the Browse... button.
Notes:
•
You cannot type or edit the name manually.
•
Make sure that you have PSERVER.NLM running if you selected Remote Printer Mode in step
8.
10. If you want to define a remote printer number slot manually, check the
Manual box and type the desired number in the box.
11. Click the OK button to return to the Network Environments window.
AXIS 5570e / AXIS 5670e User’s Manual
111
Adding Printers in NetWare
Basic Queue-based printing over IP
Axis print servers with software version 6.0 or later allow users to print in
a Pure IP environment using traditional queue-based printing (which
usually uses the IPX transport protocol). Note that only NDS queue-based
printing is supported.
In the NetWare Pure IP environment, you must use the NetWare
Administrator to create the printer, print server and queue objects.
Installing the
Axis Network Print
Server
Follow the instructions below to install the Axis Network Print Server in
the NetWare Pure IP environment:
1. Start the Configuration Wizard from the User mode in the Axis Network
Print Server Web interface.
2. Click your way through the Wizard until reaching the NetWare page.
3. Set the parameters on the NetWare page:
• PSERVER NDS Tree (example: NW5TREE)
or
PSERVER NDS File Server: (example: FILESERVERNAME)
• PSERVER NDS Distinguished Name:
(example: AXISXXXXXX.<context>, where <context> is the container
where you want to create your print server)
Setting the PSERVER parameters in the Axis Network Print Server Web interface.
4. Use the NetWare Administrator to create the printer, print server and queue
objects in the NDS tree and then link them together. The Print Services
Quick Setup (Non-NDPS) utility can be used for this. Go to Tools in the
NetWare Administrator.
112
AXIS 5570e / AXIS 5670e User’s Manual
Adding Printers in NetWare
5. Use the Add Printer Wizard on your work station to install the printer on
your client. Note that only NDS queue based PSERVER printing is supported.
When installing, choose Network Printer and browse to the queue you have
just created. Alternatively, choose Local Printer and select the queue you
have just captured.
Any configuration and management of the Axis Network Print Server can
be performed from any standard Web browser. Please refer to “Using a
Web Browser for Print Server Management” on page 128.
If both the IPX and IP protocols are enabled in your network and the print
server uses DUAL_STACK (enabled by default) as its network transport
protocol, then IPX will be chosen. To force the print server to use the IP
transport protocol, go to your print server’s Web interface and choose
Admin | Detailed View | NetWare and change the NetWare Transport
Protocol from DUAL_STACK to IP_ONLY. Save and exit when finished.
Note:
Pure IP requires that you run NetWare 5 or higher.
Queue-based Printing
Methods
Print Server Mode
The following overview explains the advantages and limitations of the
two supported queue-based printing methods.
The Axis Network Print Server logs in to a file server(s) and repeatedly
polls the print queues for print jobs. In this fashion, the Axis Network
Print Server emulates a NetWare print server, which is a workstation
running PSERVER. It provides high printing speed with low network load
and is the recommended mode for medium to large sized networks. Each
print server in PSERVER mode takes one NetWare user license.
Advantages
•
High performance: up to 1 Mbyte/s
Limitations
•
In bindery mode, this printing method requires a NetWare user licence
for each Axis Network Print Server to file server link.
Remote Printer Mode
The Axis Network Print Server acts as Remote Printer for PSERVER.NLM
running on the NetWare file server, or to a dedicated workstation running
PSERVER.EXE. In this fashion, the Axis Network Print Server emulates a
workstation running the NetWare remote printer software RPRINTER, or
NPRINTER. This mode is only recommended for small networks where the
number of NetWare user licences is a major issue.
Advantages
•
NetWare user licences are not required.
Limitations
•
•
Lower performance, typically 20 - 70 kbytes/s for NLM.
Higher network load.
AXIS 5570e / AXIS 5670e User’s Manual
113
Adding Printers in NetWare
Using Novell Utilities
NetWare
Administration
Printer Status
114
After installing the Axis Network Print Server into the NetWare
environment, you can manage your Axis Network Print Server, using
either Novell’s NetWare Administrator, or PCONSOLE.
Some useful features provided by the NetWare Administrator are
described in more detail below:
The Printer Status menu, detailed below, shows the status of an active
print job serviced by an Axis Network Print Server. It displays detailed
information concerning the active job including, Print Queue, print job
description, size of print file, percentage of job completed, etc. You can
also abort or pause the print job from this menu.
Notification
You can use the NetWare Administrator to enable or disable status
notification messages for printers connected to the AXIS 5570e/AXIS
5670e, e.g. Busy, Off-line, Out of paper, Paper jam, etc. You can also add
or remove print job owners and administrators from the list of persons to
be notified.
Print Layout
You can view installed AXIS 5570e/AXIS 5670e and their relative print
queues for any NetWare Organizational Unit. You can also display
summary information by right-clicking on the printer object you want to
examine.
AXIS 5570e / AXIS 5670e User’s Manual
Adding Printers in UNIX/Linux
Section 9
Adding Printers in UNIX/Linux
Print Tools
For printer configuration, printtool and printconfig are the most common.
How they are invoked depends on which distribution and window
manager you use.
AIX
SMIT is the recommended printing tool. It contains an integrated printer
driver list, but does not have printer detection functionality.
Instructions:
Type the command smit in a Terminal window, then click Print
Spooling.
Debian
printtool is the recommended printing tool. The program contains an
integrated printer driver list, but does not have printer detection
functionality.
Instructions:
Type the command printtool in a Terminal window to start the
graphical version.
HP UX
Sam is the recommended printing tool. It doesn’t provide an integrated
printer driver list, nor printer detection functionality.
Instructions:
Type the command sam in a Terminal window, click Printers and
Plotters and then click Actions and Add_Remote Printer/Plotter.
Mandrake
Red Hat
printerdrake is the recommended printing tool. It contains an integrated
printer driver list, but does not have printer detection ability.
printconf is the recommended printing tool. The program contains an
integrated printer driver list, but does not have printer detection
functionality.
Instructions:
Type the command printconf-gui in a Terminal window to start the
graphical version.
You can also run printconf as a text-based application if you do not have
the X Window System installed, or if you prefer the text-based interface.
Log in as root (or use the command su to temporarily change to the root
user), and type the command /usr/sbin/printconf-tui from a
shell prompt.
AXIS 5570e / AXIS 5670e User’s Manual
115
Adding Printers in UNIX/Linux
Solaris 9
The printing tool is called Printer Administrator. This operating
environment has an integrated printer driver list, but does not have
printer detection functionality.
Instructions:
Type the command /usr/sadm/admin/bin/printmgr in a Terminal
window.
SuSE
YaST2 is the recommended printing tool. It contains a printer driver list
as well as printer detection capability.
Instructions:
To start the Printer Configuration tool, select this from the Desktop:
YaST2 menu button (on the panel) | In Yast Control Center | Hardware
| Edit Printers
Notes:
• A versatile IPP client for UNIX/Linux is CUPS. It can be downloaded from the Common Unix
Printing System’s Web site at www.cups.org
• If you don't find your specific printer in your distribution, have a look at
http://www.linuxprinting.org/database.html
Typical Invocation via a Windows Manager
Using the Mandrake 8.2 distribution (with CUPS installed) and the KDE
windows manger as an example, a typical set-up begins with starting
Mandrake Control Center.
1. Click Hardware | Printer and the Printerdrake application will be invoked.
2. Click Expert Mode to be able to add a network printer.
3. Click the Add a new printer button.
Print Queues
Five types of print queues can be configured in the Mandrake
distribution:
•
•
•
•
•
116
Local Printer
Printer on remote lpd server
Network printer (TCP/Socket)
Printer on SMB/Windows 95/98/NT server
A printer device URl
AXIS 5570e / AXIS 5670e User’s Manual
Adding Printers in UNIX/Linux
1. Select the Network printer radio button and click Next.
2. Enter the IP address or host name of the print server as well as the port you
want to use. Port numbers available for TCP/IP are:
Ports numbers
USB port
Parallel port 1 Parallel port 2
Serial port
AXIS 5570e
9902
9900
—
—
AXIS 5670e
—
9900
9902
9901
Also see “TCP Ports Opened for Raw Printing” on page 276.
3. Click Next. Fill in data to help users identify the printer, i.e. name, description
and location. Click Next.
4. Select printer model and click Next.
5. Configure the printer and click Next.
6. The printer is set up. Click Finish and the printer is accessible.
Typical Invocation from a Terminal Window
Still using Mandrake as an example, open a Terminal Window and type
the command printtool. If you are in a terminal window, the graphic
version will start (as described above). If you do not have the X Window
System installed, the command will start a text based version. The same
information as was described above will be needed.
Note:
In Mandrake, even if you type printtool at a shell prompt, printerdrake will
automatically start.
AXIS 5570e / AXIS 5670e User’s Manual
117
Adding Printers in UNIX/Linux
Debian 3.0
Debian offers a choice between plain LPD, LPRng and CUPS. There are
several printer configuration tools in this distribution, e.g. the apsfilter
(version 5 or later), which adds support for LPRng and Ghostscript's
uniprint driver scheme. Red Hat's printtool is also supported, for those
who prefer GUI administration tools.
For LPRng, LPD and CUPS use the Printtool.
Invocation
1. From the Gnome desktop, select Main Menu (on the panel) => Debian
menus => Apps => System => Printtool.
2. On the KDE desktop, select the Main Menu (on the Panel) => System =>
Debian => Printtool.
3. Open a terminal window and type the command printtool (in XTERM or
Gnome).
Print Queues
Five types of print queues can be configured with printconf in the Debian
distribution:
•
•
•
•
•
Adding a Remote Unix
Printer
Local Printer
Unix Printer (lpd Spool
Windows Printer (SMB)
Novell Printer (NCP Queue)
JetDirect Printer
1. Start printtool and click Add.
2. Select Remote Unix (lpd) Queue from the Printer Type menu, and click OK.
3. Text fields for the following options appears:
• Printer name — Enter a unique name for the printer. (The name
cannot contain spaces and must begin with a letter. Valid characters
are a - z, A - Z, 0 - 9, -, and _.
• Remote Host — The hostname or IP address of the remote machine
to which the printer is attached.
• Remote Queue and input filter — The remote printer queue and
input filter.
4. Click Next to continue.
5. Click Select to choose a printer driver and to set it up. Click OK. Finally, click
Test and print a test page.
118
AXIS 5570e / AXIS 5670e User’s Manual
Adding Printers in UNIX/Linux
Red Hat 7.3
Printtool has been replaced by Printconf. The utility maintains the
/etc/printcap configuration file, print spool directories, and print filters.
Note:
If you type printtool at a shell prompt, printconf will automatically start.
Invocation
1. On the Gnome desktop, select the Main Menu button (on the Panel) =>
Programs => System => Printer Configuration to start the graphical
version.
2. On the KDE desktop, select the Main Menu button (on the Panel) => Red
Hat => System => Printer Configuration to start the graphical version.
3. Type the command printconf -gui at a shell prompt (for example, in an
XTerm or a Gnome terminal) to start the graphical version.
4. You can also run printconf as a text based application if you do not have
the X Window System installed, or you just prefer the text based interface.
To run it, log in as root (or use the command su to temporarily change to
the root user), and type the command /usr/sbin/printconf -tui from
a shell prompt.
Print Queues
Five types of print queues can be configured with printconf in the Red
Hat distribution:
•
•
•
•
•
Local Printer
Unix Printer (lpd Spool)
Windows Printer (SMB)
Novell Printer (NCP Queue)
JetDirect Printer
Important!
• Do not edit the /etc/printcap file. Each time the printer deamon (lpd) is started /restarted, a
new /etc/printcap file is dynamically created.
• If you want to add a printer without using printconf, edit the /etc/printcap.local file. The
entries in /etc/printcap.local are not displayed in printconf but are read by the printer
daemon.
• If you upgrade your system from a previous version of Red Hat Linux, your existing
configuration file is converted to the new format used by printconf. Each time a new
configuration file is generated by printconf, the old file is saved as /etc/printcap.old.
• If you add a new print queue or modify an existing one, you need to restart the printer
daemon (lpd) for the changes to take effect.
• Clicking the Apply button saves any changes that you have made and restarts the printer
daemon. The changes are not written to the /etc/printcap configuration file until the
printer daemon (lpd) is restarted. Alternatively, you can choose File => Save Changes and
then choose File => Restart lpd to save your changes and then restart the printer daemon.
• If a printer appears in the main printer list with the Queue Type set to INVALID, the printer
configuration is missing options that are required for the printer to function properly. To
remove this printer from the list, select it from the list and click the Delete button.
AXIS 5570e / AXIS 5670e User’s Manual
119
Adding Printers in UNIX/Linux
Adding a Remote
Unix Printer
To add a remote UNIX printer, such as one attached to a different
UNIX/Linux system on the same network, click the New button in the
main printconf window.
Select Unix Printer from the Queue Type menu, and click Next.
Enter a unique name for the printer in the Queue Name text field. The
printer name cannot contain spaces and must begin with a letter a
through z or A through Z. The valid characters are a through z, A through
Z, 0 through 9, -, and _. Click Next.
Text fields for the following options appear:
•
Server — The hostname or IP address of the remote machine to which
the printer is attached.
• Queue — The remote printer queue. The default printer queue is usually
lp.
By default, the Strict RFC1179 Compliance option is not chosen. If you
are having problems printing to a non-Linux lpd queue, choose this
option to disable enhanced LPRng printing features.
Click Next to continue
The next step is to select the type of printer that is connected to the
remote system.
Important!
The remote machine must be configured to allow the local machine to print on the desired
queue. As root, create the file /etc/hosts.lpd on the remote machine to which the
printer is attached. On separate lines in the file, add the IP address or hostname of each
machine which should have printing privileges.
Selecting the Print
Driver
120
If you are configuring a local printer, select the print driver from the list.
The printers are divided by manufacturers. Click the arrow beside the
manufacturer for your printer. Find your printer from the expanded list,
and click the arrow beside the printer name. A list of drivers for your
printer will appear. Select one. Then finish the Wizard in the usual
manner.
AXIS 5570e / AXIS 5670e User’s Manual
Adding Printers in UNIX/Linux
SuSE 8.0
The printing system on SuSE Linux is based on an apsfilter, with some
enhancements; SuSE's apsfilter will recognize all common file formats
(including HTML, if html2ps is installed).
There are two ways to setup printers on SuSE systems:
•
•
Invocation of YaST2
Print Queues
YaST2 will let you configure "PostScript", "DeskJet" and "Other
printers", supported by Ghostscript drivers; it's also possible to setup
HP's GDI printers (DeskJet 710/720, 820, 1000, via the "ppa" package).
YaST2 will provide /etc/printcap entries for every printer ("raw", "ascii",
"auto" and "color", if the printer to configure is a color printer). YaST2
will create spool directories and it will arrange apsfilterrc files, where
you're able to fine tune some settings (Ghostscript preloads, paper size,
paper orientation, resolution, printer escape sequences, etc.). With
YaST2 it's also possible to setup network printers (TCP/IP, Samba, or
Novell NetWare Printer).
SuSE includes the regular SETUP program from the original apsfilter
package (with some enhancements); run lprsetup to invoke this
configuration script. Once you get accustomed to its GUI, you'll be able
to configure local and network printers.
On the Gnome desktop select YaST2 Menu Button (on the panel) => Yast
Control Center => Hardware => Edit Printers to start the Printer
Configuration tool.
On the KDE desktop select YaST Menu Button (on the panel) => Yast2
modules => Hardware => Edit printers to start the graphic version.
SuSE and YaST2 differ between these printer connections:
• Local printers (Parallel, USB, Serial and Disk File)
• LPD protocol network printing (Forward queue to a remote LPD and
Prefiltered queue for an LPD forwarding queue)
• Other network printing (Samba/Windows, Novell)
The SuSE installation manual explains the setup procedures in detail.
AXIS 5570e / AXIS 5670e User’s Manual
121
Adding Printers in UNIX/Linux
AXIS axinstall Script
Having performed the basic TCP/IP setup procedures as defined earlier in
this manual, you are now able to print in interactive mode using PROS,
LPR, FTP or Reverse Telnet protocols. However, if you want to integrate
the AXIS 5570e/AXIS 5670e with your host spooler, you can use the Axis
automatic installation script axinstall. The axinstall script is available
from ftp://ftp.axis.com/pub_soft/prt_srv/utility/axinstall/latest/
After executing this script, the printer connected to the print server will
appear as though it is directly connected to the host printer spooler.
If you intend to use the print server in a multi-protocol environment,
refer to the chapters pertaining to the respective operating systems in this
manual.
When the
axinstall script has been downloaded to your host, execute the
script with this command:
sh axinstall or sh ./axinstall (depending on your system).
You will be guided through the installation by a step-by-step procedure.
During the installation you will be asked to select a print method; we
suggest you choose LPD or, for more functionality, use the PROS filter or
named pipe methods. Please refer to the following pages if you need
guidance on the choice of print methods.
Note: NLPRng is not supported by axinstall.
The axinstall script will suggest one of the systems listed below when
started. If you do not find the suggestion appropriate, then manually
select any of the systems listed.
1....SunOS 4 (SUN BSD, Solaris 1.x)
2....SunOS 5 (SUN SYS V, Solaris 2.x)
3....AIX (IBM RS/6000, BULL DPX 20)
4....HP-UX (HP 9000)
5....BOS (BULL DPX 2)
6....DEC OSF/1 (Digital Equipment, Alpha)
7....ULTRIX (Digital Equipment, DEC)
8....IRIX (Silicon Graphics, SGI)
9....SCO UNIX (Santa Cruz Operation)
10...SCO UnixWare 2.x
11...SCO UnixWare 7
12...SCO OpenServer
13...FreeBSD (Berkeley UNIX)
14...Linux
15...Generic BSD (Berkeley UNIX)
16...Generic SYS V R3 (UNIX System V Release 3)
17...Generic SYS V R4 (UNIX System V Release 4)
Systems supported by axinstall
122
AXIS 5570e / AXIS 5670e User’s Manual
Adding Printers in UNIX/Linux
Print Methods on TCP/IP Networks
The AXIS 5570e/AXIS 5670e supports several different print methods in
the TCP/IP environment. axinstall will suggest a print method suitable for
your particular UNIX/Linux system, but you might want to use another
method depending on your printing requirements (banner pages, status
logging, etc).
The diagram below shows the alternative data paths taken by some of the
UNIX/Linux print methods. This illustrates some of the advantages and
limitations of the different methods. Use the following information to
determine which method to adopt.
Print
Spooler
File to
Print
Devices
Filter/
Interface
Model
Parallel Port
Directly
connected
printer
Named Pipe
DIRECT
FTP
RTELNET
LPD FTP
RTELNET PROS B
Printer
PROS print
daemon
PROS A
Axis Network Print Server
Illustration of different UNIX/Linux print methods
LPD
The Line Printer Daemon is a protocol for transferring print jobs between
hosts. This is the recommended method for UNIX/Linux systems, but
some System V versions do not support LPD.
Advantages:
Easy to set up — install the AXIS 5570e/AXIS 5670e as a remote queue in
System V, or add a remote printer to /etc/printcap using the rm and rp
fields (BSD).
Limitations:
Spooler features, and printcap or lpr options (BSD) such as multiple
copies, are not available.
FTP
The File Transfer Protocol is used for transferring files between hosts.
Advantages:
Uses industry standard network software on the host.
Limitations:
No printer status logging. In the case of BSD it may conflict with other
input or output filters and does not allow both input and output filters. In
System V no filters or interface programs can be used.
AXIS 5570e / AXIS 5670e User’s Manual
123
Adding Printers in UNIX/Linux
PROS
A protocol developed at Axis. Comes in two versions;
named pipe (PROS A) and filter (PROS B).
PROS A
Advantages
The AXIS 5570e/AXIS 5670e appears as a device to the system. This
makes all filter and model options available. It provides accounting and
status logging. Supports bi-directional printing. The printer information
read back can be viewed in a log file.
PROS A
Limitations
A ‘C’ compiler is required to build the PROS A drivers.
Note:
You can download a ‘C’ compiler from http://www.gnu.org/.
PROS B
Advantages
It provides accounting and status logging. Supports bi-directional
printing. The printer information read back can be viewed in a log file.
PROS B
Limitations
A ‘C’ compiler is required to build the PROS B drivers and in the case of
BSD, it may conflict with other input or output filters. It does not allow
both input and output filters. Interface programs can not be used in
System V.
Reverse Telnet
Often used for printing via a terminal server printer port. Only
recommended if you already have a Reverse Telnet driver installed.
Advantages:
Easy to set up with previously installed Reverse Telnet drivers.
Limitations:
No status logging. Drivers are not supplied with the print server. Existing
drivers may be slow.
Other UNIX/Linux
Systems
Most UNIX/Linux systems resemble either BSD or System V and so with
some ingenuity, a solution can also be devised for other variants.
If the system has BSD socket type networking support, then prosbsd (in
the bsd directory of the AXIS 5570e/AXIS 5670e) can be used as a
starting point. It receives print data from stdin, and writes a log file to
stderr. Nothing is written to stdout.
Alternatively, FTP may be used. It is a good idea to use bsd/ftp_bsd or
as a starting point.
sysv/ftp_sysv
IBM MVS Systems
124
A sample JCL script, jclex, is available in the mvs directory of the print
server. It gives an example of how to print a file from an MVS mainframe
to an AXIS 5570e/AXIS 5670e using FTP.
AXIS 5570e / AXIS 5670e User’s Manual
Adding Printers in OS/2
Section 10
Adding Printers in OS/2
Having connected the Axis Network Print Server to your network, as
described in “Connect the Hardware” on page 14, this section now
describes how to set up your Axis Network Print Server for printing in the
OS/2 environment.
Continue with the instructions presented in the table below:
Printing protocol
See ...
TCP/IP
“TCP/IP Printing” on page 125
NetBIOS/NetBEUI
“NetBIOS/NetBEUI Printing in OS/2” on page 126
If you intend to operate your AXIS 5570e/AXIS 5670e in a multi-protocol,
mixed environment, you should also proceed to the other relevant sections in
this manual.
TCP/IP Printing
Having assigned an IP address to the Axis Network Print Server, as
described in “Setting the IP Address” on page 16, you are now ready to
install it for TCP/IP printing in the OS/2 environment. The Axis Network
Print Server supports LPR Printing using the lprportd service method.
Installing the
Axis Network Print
Server
Follow the instructions below to install the print server using the lprportd
service method:
1. Open the OS/2 System window, select TCP/IP and TCP/IP Configuration.
2. Select Printing, type a number, e.g. 3, in the Maximum number of LPD ports
field. The Remote print server and Remote print server's printer fields should
remain empty.
3. Select Autostart, select lprportd, click the Autostart check box and select
Detached.
4. Exit and Save.
5. Restart your OS/2 client.
Creating a
Print Queue
Continue with the instructions below to create a print queue:
1. Open the Template group. Create an new printer from Templates by
dragging the Printer icon to the desktop with the right mouse button.
2. Select a printer driver and double-click a free Output port, for instance
\PIPE\LPD0.
3. Enter the host name or the IP address of the Axis Network Print Server in
the LPD server field.
4. Enter one of the Axis Network Print Server logical printer names, for
example pr1, in the LPD printer field.
AXIS 5570e / AXIS 5670e User’s Manual
125
Adding Printers in OS/2
NetBIOS/NetBEUI Printing in OS/2
AXIS Print Utility for OS/2 is the tool to use for NetBIOS/NetBEUI
printing in OS/2 environments. This tool can be fetched from
www.axis.com => Software => Discontinued products. Install this utility
if you have not already done so.
If you want to change the default name or any of the Axis Network Print
Server default parameters, you can do so using any standard Web
browser.
Refer to Section 11 Management and Configuration, on page 128, for
more information.
The AXIS Print Utility for OS/2 is not needed on the client platforms
when using a client-server configuration.
About AXIS Print
Utility for OS/2
AXIS Print Utility for OS/2 is an application for NetBIOS/NetBEUI
printing in the OS/2 environment. Its allows you to:
•
Install and maintain the Axis Network Print Server printer ports as OS/2
printer ports.
• Capture and monitor print jobs directed to the Axis Network Print
Server ports.
Print jobs are directed through a spool directory located on your local
hard disk (peer-to-peer mode), or on the file server (client-server mode).
The printer port status of your Axis Network Print Server can be
monitored and pop-up notification messages can be generated, keeping
you informed of completed print jobs or any problem condition.
Notes:
Installing the
Axis Network Print
Server
•
The NetBEUI protocol must be active. If not, use MPTS/LAPS (LAN Server) or SETUP (LAN
Manager) to activate it.
•
If you are using OS/2 version 2.x and wish to print through TCP/IP, we recommend that
you use the IBM TCP/IP for OS/2 product. It supports the LPD and interactive FTP print
methods.
1. When AXIS Print Utility for OS/2 is running, click Install to install your
Axis Network Print Server. The ports appears in the list as <name>.LP1,
<name>.LP2 and <name>.CM1, where <name> is AX followed by the
last six digits of your print server serial number. e.g. AX100086.LP1.
2. Select the port that you want to install, then click Install.
Repeat this procedure for each server using the Axis Network Print
Server.
The AXIS Print Utility for OS/2 must be running in order to print through your Axis Network
Print Server. It is strongly recommended that you modify the startup.cmd file, enabling AXIS
Print Utility for OS/2 to automatically start when your client is re-booted. Instructions are
available in the AXIS Print Utility for OS/2 Readme file.
126
AXIS 5570e / AXIS 5670e User’s Manual
Adding Printers in OS/2
Creating
a Print Queue
(OS/2 version 2.x
and OS/2 Warp)
1. Double-click the Templates folder, then drag the Printer icon out to the
Workplace Shell (or into a folder) while holding the right mouse button
down.
2. Type a name of your choice in the Name field.
3. Select \PIPE\<name>.LP1, \PIPE\<name>.LP2 or \PIPE\<name>.CM1
from the Port list, and select a printer driver suitable for your printer from
the Standard Printer list.
4. Click OK to confirm the printer definition.
Sharing the
Print Queue
A print queue must be made a shared resource before it can be accessed
from other clients or servers. The following three examples show how you
can share your printer resources:
Open an OS/2 window and issue the following command:
NET SHARE <queue_name> /PRINT
Where <queue_name> is the name of the queue created on the previous
side.
To share a printer resource when using OS/2 Warp with IBM Peer service,
follow the steps below:
1. Click the right mouse button on the printer object.
2. Select Share and then Start sharing. In the dialog box, enter a Description.
3. Select the check-box Start sharing at LAN workstation start-up.
4. Click OK.
To share a printer resource when using LAN server 4.0, follow the steps
below:
1. Open LAN Server Administration.
2. Open your domain and then Resource Definition.
3. Drag and drop a printer from the template.
4. Enter the Alias name, select a Server name and the previously created
Spooler Queue Name.
5. Click OK.
The setup is completed and you can now print through your Axis
Network Print Server.
AXIS 5570e / AXIS 5670e User’s Manual
127
Management and Configuration
Section 11
Management and Configuration
The management and configuration tools that are supported by the Axis
Network Print Server allow you to:
•
•
•
•
•
Configuration
Overview
Change the print server parameters, i.e. editing the config file
Receive extended information about the print jobs
Receive printer port status
Monitor your printers
Reset the Axis Network Print Server
The method you should use to manage and configure your Axis Network
Print Server depends on the operating system protocols of your network.
The table below displays which method to use for each supported
environment.
Environments
Configuration/Management methods
IBM Host
(AS/400, IBM Mainframe)
From an IBM Host - See page 142
TCP/IP
(AS/400, IBM Mainframe, UNIX,
Windows, Mac OS
Web Browser - See page 128
AXIS ThinWizard - See page 133
FTP - See page 135
Telnet - See page 137
SNMP - See page 140
IPX/SPX
(NetWare)
Novell Utilities - See page 141
Windows
Web Browser - See page 128
AppleTalk
Web Browser - See page 128
AppleTalk _cfg method - See page 85
Mac-FTP - See page 135
Using a Web Browser for Print Server Management
Once you have established the Axis Network Print Server in the TCP/IP
environment, as described in “Setting the IP Address” on page 16, you are
free to access the Axis Network Print Server Web pages from any
standard Web browser.
The Web interface of the Axis Network Print Server is divided into two
modes of operation, User mode and Admin mode.
128
User
In User mode you can change language, but you have no rights to change
any other parameters. However, if you have access rights to the Admin
mode, you can change some of the basic parameters from User mode via
the Configuration Wizard. This mode is intended for regular users who are
only interested in using the print server's interface for checking print jobs
or viewing printer properties. If you want to change any other of the print
server's settings, you must enter the Admin mode.
Admin
When in Admin mode, you have access to all the print server's parameters
AXIS 5570e / AXIS 5670e User’s Manual
Management and Configuration
and you can change them to your liking. This mode is intended for
network administrators and can be password protected to prevent
unauthorized changing of the print server parameters.
Note:
To protect the Admin pages from unauthorized use, it is highly recommended that you change
the default password.
This is done from the Admin | General Settings | General tab. Enter the password in the Root
Password field.
Accessing the Web
Pages
Follow the steps below to access the internal Web pages of the Axis
Network Print Server:
1. Enter the print server’s IP address (or host name) in the Location/Address
field of your Web browser. Press Enter
2. The Printer Overview page will appear. Click Admin to access the
Administration Web pages.
3. If you have changed the User/Password combination, you will be promted
for them. Click OK.
Note:
•
Available Services
from the User Mode
You can address the print server’s Web interface via https:// To do this you must enable
the SSL/TLS protocols in the Web interface: Admin | Network Settings | Detailed View|
TCP/IP Network and set the HTTPS Enabled parameter to Yes (you must have a valid certificate loaded).If you do not have a valid certificate loaded, select Admin | Security Settings and click Create.
The following services are available from the User mode. A link to the
Axis home page is available from this mode.
AXIS 5570e / AXIS 5670e User’s Manual
129
Management and Configuration
Printer Overview
The Printer Overview page contains a section that allows you to view the
general parameter setting of the Axis Network Print Server, including the
print server name and the location of the print server in your
organization, if defined.
If you have admin access rights you can use the Configuration Wizard
for general settings to perform basic configuration of the Axis Network
Print Server and the Configuration Wizard for IBM sessions to add an
IBM session.
By clicking the printer icon a printer page opens, allowing you to view
the status and the supported capabilities of the connected printer. The
extent of this information depends on the printer model. From the printer
page, you can also print a test page to the printer.
Print Jobs
From the Print Jobs page you can view the status of the current print
jobs, including the number of printed bytes and the origin of the print
job. You can also view a log of the 20 latest print jobs that includes the
user, the printing protocol and the file size. A log that displays the
accumulated usage of the connected printers allows you to control the
usage of the connected printers.
Help
The Help page presents you with basic information about the Axis
Network Print Server and the Web user interface. A short description of
the Axis installation tools you should use when installing a printer on
your PC is also included.
Available Services
from the Admin Mode
The following services are available from the Admin mode. An additional
link to www.axis.com is available from this mode.
This Print Server
The This Print Server page contains a section that allows you to view and
modify the general parameter setting of the Axis Network Print Server,
including the print server name, the node address, the password and the
base URL. You can also configure any of the eight logical printers of the
Axis Network Print Server. Management operations, like restarting the
Axis Network Print Server and resetting its parameters to the factory
default settings, are also available.
Caution!
Any network configuration should involve the Network Administrator.
By clicking on the printer icon, a printer page opens, allowing you to
view the status and the supported capabilities of connected printer. The
extent of this information is depending on the printer model. From the
printer page, you can also print a test page to the printer.
Print Jobs
130
From the Print Jobs page you can view the status of the current print
jobs, including the number of printed bytes and the origin of the print
AXIS 5570e / AXIS 5670e User’s Manual
Management and Configuration
job. You can also view a log of the 20 latest print jobs that includes the
user, the printing protocol and the file size. A log that displays the
accumulated usage of the connected printers allows you to control the
usage of the connected printers. To delete an ongoing print job, use the
delete button next to the job.
IBM Sessions
IBM Emulators
From the IBM sessions page you can view the list of configured IBM
sessions. You can choose to edit or delete a session from the list or add a
new session from the Add Session button.
The IBM Emulators page contains three Detailed View buttons.
•
•
•
Network Settings
SCS/IPDS emulator configurations. Select the IBM printer that is to be
emulated from the drop-down list.
SCS/3270DS emulator configurations
Common emulator settings: page format, CPI mapping, job control,
3270 options, extended emulation, user driver.
IPDS emulator configurations
IPDS Emulator Settings: IPDS configuration, IPDS PostScript Driver
settings, IPDS PCL Driver settings
From the Network Settings page you can set all parameters that control
the network traffic to and from the Axis Network Print Server. You can
enable or disable any of the supported network protocols and fine-tune
the parameter settings. For additional information, see the Online Help
pages.
Support
From the Support page you can receive help to resolve any installation or
print problems that might occur. If your problems persist, the Support
page allows you to produce a Server Report. The Server Report includes
the settings of the Axis Network Print Server, information about your
connected printers as well as the current network settings. The Server
Report is of great value for support assistance, so please mail, email or fax
it to your support channel together with a detailed problem description.
Statistics
The Statistics page displays information about the network traffic to and
from the Axis Network Print Server as well as information about servers
and services that are connected or associated with the Axis Network Print
Server.
Help
The Help page displays a comprehensive description of the configuration
and management activities that can be performed from the internal Web
pages of the Axis Network Print Server. Theses activities include
instructions on how to install the Axis Network Print Server in various
environments and how to upgrade it with new firmware. A detailed index
is also available.
Security Settings
On the Security Settings page you can enable or disable SSL (Secure
AXIS 5570e / AXIS 5670e User’s Manual
131
Management and Configuration
Socket Layer - a protocol designed to provide secure communications on
the Internet.) and TLS (Transport Layer Security, a protocol that
guarantees privacy and data integrity between applications
communicating over the Internet) You can also create secure certificates
and disable/enable insecure protocols.
Whenever SSL/TLS is enabled, you have to address the print server’s Web
interface in the secure way, i.e. via https://
See Enabling Secure Web Services — SSL/TLS, on page 164 for a detailed
description.
Parameter List
Restart
Software Default
Shows all print server parameters and their current settings.
Restarts the print server.
A Software Default will reset all print server parameters and settings to
their default values except:
•
•
•
•
•
Node address (NODE_ADDR.)
IP Address (INT_ADDR.)
DHCP enabled (DHCP_ENB)
Installed certificate
Private key
See The Test Button, on page 208 for instructions on performing a
Factory Default.
Firmware Upgrade
132
Upgrades the print server’s internal software.
AXIS 5570e / AXIS 5670e User’s Manual
Management and Configuration
Using AXIS ThinWizard for Print Server Management
AXIS ThinWizard software allows you to manage and upgrade multiple
Axis products. Using a standard Web browser, you can find, install,
monitor, configure and upgrade your Axis print servers remotely in any
TCP/IP network. AXIS Thin Wizard 3.04 is Windows 2000 and Windows
XP compatible.
Installing AXIS
ThinWizard
AXIS ThinWizard software is available on www.axis.com
You should only install AXIS ThinWizard on a designated computer on
your network.
To install, follow the instructions given by the Installation Wizard. During
the installation, you will be asked to enter a user id and a password —
these will be used when logging in to AXIS ThinWizard, so please take a
note of them.
Important:
Starting AXIS
ThinWizard
•
To use all AXIS ThinWizard features, the print server must have the FTP_ENB. parameter
set to “Yes”. This is done in the print server’s Web interface: Admin | Network Settings
| Detailed View | TCP/IP Network => FTP Enabled => Yes.
•
If you disable SNMP in the print server’s Web interface, you will disable AXIS
ThinWizard’s ability to determine print server status! Enabling/Disabling SNMP is done
from Admin | Network Settings | Detailed View | SNMP
If AXIS ThinWizard is installed on the workstation you can access its
Web interface via Start | All Programs (using Windows XP or Start |
Programs using Windows 2000). If it is installed on another computer,
follow the instructions below:
1. Make sure that the computer where you installed the AXIS ThinWizard is
up and running on your network.
2. Start a Web browser on a client in your network.
3. Enter the IP address or the host name of the computer where you installed
AXIS ThinWizard. (If the server is installed on another port than 80, you must
enter the port name after the host name or the IP address).
4. The AXIS ThinWizard start page now appears in the Web browser. Enter the
user id and password you specified during installation and click Log in.
AXIS 5570e / AXIS 5670e User’s Manual
133
Management and Configuration
5. The AXIS ThinWizard interface appears:
The first time you use AXIS ThinWizard, set the Preferences to reflect
your network environment:
Select a network group from the list on the Manage Network page. If the
list is empty, you must first create a group. Click the Network Groups tab
and follow the instructions.
Creating a
Network Group in
AXIS ThinWizard
The network group concept is the corner stone of AXIS ThinWizard. By
dividing your network into network groups, you can monitor your print
servers more efficiently. The scope of each network group is determined
by the Axis server types and IP address ranges that are included. You can
create as many network groups as you want.
Follow the instructions below to create a network group:
1. Click Network Groups in the AXIS ThinWizard main menu.
2. Click Create.
3. The Create Network Group page opens. Type the name of the network group,
enter the IP address ranges and Axis server types that should be included.
If you are only interested in managing print servers, deselect all options but
the print server option.
4. Click OK to create the network group.
You can edit the properties of each network group from the Network
Groups page. Simply select the network group from the list and use one of
the Edit, Copy or Remove commands.
Managing
Print Servers
Follow the instructions below to access the AXIS 5570e/AXIS 5670e
using AXIS ThinWizard:
1. Click Manage Network in the main menu.
2. Select the network group, including the, from the drop-down list. All AXIS
servers included in the network group appear in the window.
3. Click the link of the AXIS 5570e/AXIS 5670e to access its internal Web page.
4. The ‘Srv’ and ‘Dev’ columns show the status of your print servers and printers.
134
AXIS 5570e / AXIS 5670e User’s Manual
Management and Configuration
Changing the IP
Settings
Using AXIS ThinWizard you can also set or change each print server’s IP
parameters.
1. Click IP Settings in the main menu.
2. Select print server in the list.
3. Enter your data: IP address, Subnet mask, Default gateway and the print
server’s password (default password is pass).
4. Click Set to save your settings.
5. Click Rescan to update AXIS ThinWizard and see the changes.
If Your Print Server is
not Shown in the List
If your print server is not shown in the list, click “Click here...”. By
entering the serial number of the print server (found on the underside
label) you will be able to set the print server’s IP parameters.
Example: 00408c181cf0
Upgrading
Axis Servers
Refer to “Using AXIS ThinWizard for Print Server Management” on page
133 for more information about upgrading Axis servers.
Multiple
Configuration and
Installation
Using AXIS ThinWizard it possible to change the settings of several Axis
servers simultaneously. It is also possible to copy the configuration from
one server to another. This is a convenient way to install a new server,
based on the settings of an already existing server.
For additional information, please refer to the AXIS ThinWizard online
help.
Using FTP for Print Server Management
Having assigned an IP address to your Axis Network Print Server, as
described in “Setting the IP Address” on page 16, you can change the
Axis Network Print Server parameter settings using the File Transport
Protocol (FTP).
Ensure that FTP Enabled is set to yes. To check this parameter, browse to
the print server and select Admin | Network Settings | Detailed View |
TCP/IP Network.
Editing the config file
Follow the instructions below to edit the config file using FTP:
1. Log in to the Axis Network Print Server by typing:
ftp <host name> or ftp <IP address> in a DOS window (Windows
and OS/2) or in a UNIX shell.
2. Enter the user id and the password. (The default entries are root and pass.)
3. Download the config file to your host by typing:
get config
4. Edit the file using your preferred text editor.
AXIS 5570e / AXIS 5670e User’s Manual
135
Management and Configuration
5. Save the config file to the Axis Network Print Server by typing:
put config CONFIG
Notes:
•
It is important that the destination file is specified in capital letters. Otherwise the edits
are temporary and will be lost once the Axis Network Print Server has been powered off.
•
To edit the config file from a Macintosh you will need FTP support such as MacTCP, Fetch
or Anarchie. The procedure for editing the file is the same as described above.
The example on the next page describes how to upload and download the
config file using FTP from a DOS window.
Example:
> ftp npserver
connected to npserver.
220 AXIS 5670e FTP Network Print Server V7.00 Oct 04 2004
ready.
Name (npserver:root): root
331 User name ok, need password
Password: pass
(not visible)
230 User logged in
ftp> get config
200 PORT command successful.
150 Opening data connection for CONFIG (192,168,0,10,4,5),
(mode ascii).
226 Transfer complete.
65066 bytes received in 0.52 seconds (1.2e+02 Kbytes/s)
ftp> put config CONFIG
200 PORT command successful.
150 Opening data connection for CONFIG (192,168,0,10,4,5),
(mode ascii).
226 Transfer complete.
65066 bytes sent in 0.86 seconds (74 Kbytes/s)
ftp> bye
221 Goodbye.
>
Viewing
the Account File
The account file contains data concerning the ten last print jobs. It
specifies an internal job number, the user that initiated the job, the
protocol and logical printer that was used, current status (Completed, Offline, or Printing), number of bytes printed, elapsed time and off- line
time.
Follow the instructions below to view the account file using FTP:
1. Log in to the Axis Network Print Server by typing:
ftp <host name> or ftp <IP address> in a DOS windows (Windows
and OS/2) or in a UNIX shell.
2. Enter the user id and the password. (The default entries are root and pass.)
136
AXIS 5570e / AXIS 5670e User’s Manual
Management and Configuration
3. Download the account file to your host by typing:
get account
4. View the account file using your preferred text editor.
Viewing
the Status File
The status command shows which printer port the logical printers are
assigned to, and their current status.
Follow the instructions below to view the status file using FTP:
1. Log in to the Axis Network Print Server by typing:
ftp <host name> or ftp <IP address> in a DOS windows (Windows
and OS/2) or in a UNIX shell.
2. Enter the user id and the password. (The default entries are root and pass.)
3. Download the status file to your host by typing:
get status
4. View the status file using your preferred text editor.
FTP Help
By typing help in step 3 in the FTP instruction sets above, a list of all
available files and commands will be displayed.
Using Telnet
Having assigned an IP address to your Axis Network Print Server, as
described in “Setting the IP Address” on page 16, you can manage your
Axis Network Print Server using the Telnet protocol.
Viewing
the Account File
The account file contains data concerning the last ten print jobs. It
specifies an internal job number, the user that initiated the job, the
protocol and logical printer that was used, current status (Completed, Offline, or Printing), number of bytes printed, elapsed time and off-line time.
Follow the instructions below to view the account file using telnet:
1. Log in to the Axis Network Print Server by typing:
telnet <host name> or telnet <IP address> in a DOS window
(Windows and OS/2) or in a UNIX shell.
2. Enter the user id and the password. (The default entries are root and pass.)
3. View the account file by typing:
account
The example below shows how to view the account file using Telnet from
a UNIX shell.
AXIS 5570e / AXIS 5670e User’s Manual
137
Management and Configuration
Example:
> telnet npserver
Trying 192.36.253.96...
Connected to npserver.
Escape character is ‘^]’.
AXIS 5670e TELNET Network Print Server V7.00 Oct 04 2004
AXIS 5670e network login: root
Password: pass
(not visible)
AXIS 5670e TELNET Network Print Server V7.00 Oct 04 2004
Root> account
Current account file:
JOB
USER
PROT
2
LSLM_user
LAN Server/Man.
1
Administrator LPD
PORT
S
BYTES
ETIME
PR1
C
188313
1
pr1
C
244513
1
Root>
Typical Telnet session to view the Account File
Viewing
the Status file
The status command shows which printer port the logical printers are
assigned to, and their current status.
Follow the instructions below to view the status file using telnet:
1. Log in to the Axis Network Print Server by typing:
telnet <host name> or telnet <IP address> in a DOS window
(Windows and OS/2) or in a UNIX shell.
2. Enter the user id and the password. (The default entries are root and pass.)
3. View the status file by typing: status
Performing Resets
Three types of reset commands allow you to perform soft resets, to
perform hard resets, and to reset the print server’s parameters to its
default settings.
Follow the instructions below to perform a soft reset using telnet:
1. Log in to the Axis Network Print Server by typing:
telnet <host name> or telnet <IP address> in a DOS window
(Windows and OS/2) or in a UNIX shell.
2. Enter the user id and the password. (The default entries are root and pass.)
3. Restart the print server’s protocols by typing:
softreset
Replace the command in step 3 above with hardreset or default to
perform the other two reset operations.
138
AXIS 5570e / AXIS 5670e User’s Manual
Management and Configuration
Printing Hexdumps
The Axis Network Print Server allows you to record a trace of the
communication between the Axis Network Print Server and the host.
The Axis Network Print Server supports hexdump printing for the SNA,
TN3270E, TN5250E, LPR/LPD and Raw TCP/IP printing protocols. Please
refer to “Protocols and Datastreams” on page 9 for details on the
supported protocols.
Follow the instructions below to perform a hexdump printout for the SNA
printing protocol:
1. Log in to the Axis Network Print Server by typing:
telnet <host name> or telnet <IP address> in a DOS windows
(Windows and OS/2) or in a UNIX shell.
2. Enter the user id and the password. (The default entries are root and pass.)
3. Enable the Axis Network Print Server to hexdump mode by typing:
snahexdump
4. Select Start Logging from the Terminal menu in the Telnet window. Specify
a file name and select the folder where you want to save the file.
5. Start the print job.
6. When the print job is finished, select Stop Logging from the Terminal menu.
7. Enter the quit command
Replace the command in step 3 above with tnehexdump for the TN3270E
and TN5250E protocols, lpdhexdump for the LPR/LPD protocol, or
rtnhexdump for the reverse Telnet protocol.
Telnet Help
By typing help in step 3 in any of the Telnet instruction sets above, a list
of all available commands will be displayed.
AXIS 5570e / AXIS 5670e User’s Manual
139
Management and Configuration
Using SNMP
You can use SNMP (Simple Network Management Protocol) for remotely
monitoring and configuring of the Axis Network Print Server. All major
functions for print servers are supported.
General Information
SNMP refers to a set of standards for network management, including a
protocol, a database structure specification, and a set of data objects. The
Axis Network Print Server SNMP implementation runs in the TCP/IP
environment.
The management is handled by NMS (Network Management System)
software running on a host on your network. The NMS software
communicates with network devices by the means of messages, which are
references to one or more objects.
A message can be a question or an instruction to a device, or an alarm
triggered by a specific event in a device. Objects are contained in data
bases called MIBs (Management Information Base), where MIB-II is a
standard database.
The Axis Network Print Server supports all relevant parts of MIB-II and
also includes a private enterprise MIB. Refer to The AXIS MIB, on page
140.
System Requirements
for SNMP
The following requirements must be fulfilled in order to make full use of
the Axis Network Print Server SNMP support:
•
•
NMS software that allows you to install private enterprise MIBs
A host, supporting FTP, on which to run the NMS software
Follow these steps to add the AXIS MIB to your NMS software:
1. Log in to the Axis Network Print Server using FTP.
2. Download the MIB file /snmp/axis.mib to the NMS host.
3. Install the AXIS MIB according to instructions in your NMS software
documentation.
The AXIS MIB
The AXIS MIB contains a large number of objects which may be
categorized as follows:
•
Menu objects - used for viewing and changing the Axis Network Print
Server configuration from the NMS program. Refer to The Parameter
List, on page 216.
• Printer status and unit administration objects - used for monitoring
Axis Network Print Server print jobs and storing parameter changes
permanently.
• Trap objects - used for alarms at various error conditions.
For technical details, you can view the MIB file (axis.mib) with any text
editor.
140
AXIS 5570e / AXIS 5670e User’s Manual
Management and Configuration
SNMP Device Index
When using the TCP/IP protocol (and if the printer driver permits), the
print server can use SNMP Status to find out if the printer is ready to
accept a new job. See “SNMP Device Index” on page 276.
Using Novell Utilities
After installing the Axis Network Print Server into the NetWare
environment, you can manage your Axis Network Print Server, using
either PCONSOLE, Novell’s NetWare Administrator, or iPrint.
NetWare
Administration
Printer Status
Some useful features provided by the NetWare Administrator are
described in more detail below:
The Printer Status menu, detailed below, shows the status of an active
print job serviced by an Axis Network Print Server network print server. It
displays detailed information concerning the active job including, Print
Queue, print job description, size of print file, percentage of job
completed, etc. You can also abort or pause the print job from this menu.
NetWare Administrator Printer Status Menu
Notification
You can use the NetWare Administrator to enable or disable status
notification messages for printers connected to the Axis Network Print
Server, e.g. Busy, Off-line, Out of paper, Paper jam, etc. You can also add
or remove print job owners and administrators from the list of persons to
be notified.
Print Layout
You can view installed Axis Network Print Server Network Print Servers
and their relative print queues for any NetWare Organizational Unit. You
can also display summary information by right-clicking on the printer
object you want to examine.
AXIS 5570e / AXIS 5670e User’s Manual
141
Management and Configuration
NetWare Print Layout with corresponding information summary
Configuring the Print Server from an IBM Host
Once communication with an IBM host has been established, all the Axis
Network Print Server parameters can be edited by printing a file
containing special configuration commands. To start the configuration,
the command %CONFIG+ is entered in the file. To protect your settings, a
password must be provided. By default, the password is pass. When all
parameters are set, the command SAVE is used to store the parameters
permanently. The command %CONFIG- leaves the configuration mode and
resumes normal printing. The syntax for the file to print is:
%CONFIG+ <password;>
IBM_PRINTING_PARAMETER_NAME = VALUE;
SAVE;
%CONFIG-
In order to maintain backward compatibility and increase security, many
parameters that are not related to the IBM printing operation have to be
preceded by the %CONFIG++ command. When all parameters are set, enter
%CONFIG--. The parameters requiring %CONFIG++ are clearly marked in the
parameter listing on the following pages.
%CONFIG+ <password;>
IBM_PRINTING_PARAMETER_NAME = VALUE;
%CONFIG++
PARAMETER_NAME = VALUE;
%CONFIG-SAVE;
%CONFIG-
142
AXIS 5570e / AXIS 5670e User’s Manual
Management and Configuration
Select the PCL5 printer driver and disable the NetWare protocol:
%CONFIG+ password;
PRDRIVER = PCL5;
%CONFIG++
NETW_ENB = NO;
%CONFIG-SAVE;
%CONFIG-
(If you have not changed the default
password (pass), the password is optional)
For parameters requiring more than one value, the values should be separated using a comma.
AXIS 5570e / AXIS 5670e User’s Manual
143
Configuration Possibilities
Section 12
Configuration Possibilities
This section describes some special features offered by the AXIS
5570e/AXIS 5670e:
Autodetect Printer Type, on page 144
Auto-IP, on page 144
Changing Language in the Print Server’s Web Interface, on page 145
E-mail Notification, on page 145
Flash Loading of Firmware over the Web, on page 162
IPP (Internet Printing Protocol), on page 146
Logical Printers for Customized Printing, on page 154
Network Speed, on page 161
NetWare Packet Signature Levels, on page 162
Overriding Port Status, on page 168
TCP/IP Restrictions, on page 163
Enabling Secure Web Services — SSL/TLS, on page 164
Autodetect Printer Type
The print server can automatically detect the type of printer you are using
if you enable Autodetect Printer Type. The print server can then
recognize Epson and Hewlett Packard InkJet printers. Most Epson and
Hewlett Packard InkJet printers that have Mac OS printer drivers for
network printing are supported. If Autodetect Printer Type is disabled,
the AppleTalk printer type has to be specified manually in the print
server. For Epson InkJets it would be "EPSONLQ2" and for HP InkJets it
would be "DeskWriter". If the print server does not recognize the
connected printer the default setting, "LaserWriter" will be used as printer
type. "LaserWriter" is the recommended setting to be used with all
PostScript printers.
To enable Autodetect Printer Type, log in to your print server’s Web
interface and select Admin | Network Settings | Detailed View |
Macintosh | Auto Detect Printer Type | Yes.
See the Help pages in the print server’s Web interface for details.
Auto-IP
In the absence of an IP address management mechanism such as DHCP,
the print server will receive a temporary IP address automatically over
144
AXIS 5570e / AXIS 5670e User’s Manual
Configuration Possibilities
Auto-IP, a method which enables the host to automatically take a
linklocal IPv4 address. Auto-IP is supported by Windows 98, Me, 2000,
XP and Mac OS version 8.5 or higher.
See “Dynamic IP Address Assignment” on page 16.
Changing Language in the Print Server’s Web Interface
English, French, German, Italian, Japanese and Spanish is supported in
the print server's Web interface, with English as the default language. You
can change the language used for the print server’s Web interface from
the User mode:
1. Click the Change button next to Language.
2. Choose your preferred language and character set from the drop-down
lists, click OK and then press F5 to refresh the view.
You can change the Character Set by clicking the Change button. The
default Character Set is ISO-8859-1, which can be applied in most cases.
Japanese requires SHIFT_JIS.
E-mail Notification
Whenever an event that needs human intervention occurs in a network
printer, the concerned person can be notified by e-mail. This ’troublereport’ contains a short and concise description of the event. Five events
are covered: Paper Jam, Out of Paper, Toner Low, No Toner, Printer
Off-line.
In order to determine who the e-mail recipients will be of these different
trouble-reports, follow these instructions:
1. From your print server’s internal Web page, go to: Admin | Network
Settings | Detailed View | e-mail Notification. The following options will
appear:
Options
E-mail recipient
Administrator e-mail
Address
This address will be used as “Reply to”-address in the e-mails
PAPER JAM
The person responsible for handling paper jams in the printer
OUT OF PAPER
The person responsible for filling the printer with paper
TONER LOW
The person responsible for filling up the toner in the printer
NO TONER
The person responsible for changing the toner in the printer
PRINTER OFFLINE
The person responsible for the overall maintenance of printer
2. Enter the respective e-mail addresses of the trouble-report recipients in the
blank fields as follows:
[email protected]
3. Click OK and exit when done.
AXIS 5570e / AXIS 5670e User’s Manual
145
Configuration Possibilities
Important:
Check that the SMTP Server and Domain Name parameters in the print server’s internal Web
pages are correct. This is done in: Admin | Network Settings | Detailed View | TCP/IP
Network
IPP (Internet Printing Protocol)
The Axis Network Print Server enables printing over the Internet with IPP
(Internet Printing Protocol), an industry standard that allows users to
print to remote printers across the Internet.
With IPP, a user with an Internet connection can send a document to any
printer which is connected to the Internet. IPP is platform independent
and can be used to print over any LAN or WAN that supports TCP/IP.
In practical terms, this means that you can send documents to a remote
printer as an addition to or replacement of fax and e-mail, with the same
quality and color options of traditional network printing.
IPP clients
An IPP client needs to be installed on your computer together with an
appropriate printer driver for proper IPP functionality. The IPP client is a
tool that adds destination printers to your printer list.
The Axis Network Print Server with integrated IPP is compatible with any
1.0 and 1.1 compliant IPP client.
The Axis Network Print Server presents IPP printer objects to the client,
one for each printer port. Some of the most common IPP client printing
methods are described below. Please refer to your IPP client
documentation for more specific information.
Currently Available IPP
Clients on the Market:
•
•
•
•
•
146
For Windows 2000/XP/2003: the Microsoft IPP Client (automatically
installed with the Operating System).
For Windows 98, NT: IPP clients can be downloaded from the
Microsoft Web site.
For UNIX/Linux: CUPS (can be downloaded from the Common Unix
Printing System Web site at www.cups.org).
If you wish to print using iPrint over IPP, use AXIS IPP Gateway
Configuration Snap-in for iPrint in NetWare 5.x. It is available on
www.axis.com (Support | Select Software). See its read-me file for
installation instructions.
For Windows NT/2000: the Internet Printer Connection software from
Hewlett Packard (can be downloaded from the Hewlett Packard Web
site).
AXIS 5570e / AXIS 5670e User’s Manual
Configuration Possibilities
IPP Printing
Requirements
Address Schemes for
IPP Printers
Before you print to an IPP printer you need to know:
•
•
the address of the print server.
the brand and model of the printer in order to install the appropriate
printer driver.
When using IPP printing, you need to know the IP address or host name
of your Axis print server. IPP is a client/server type protocol which
comprises two industry standards:
•
•
the 1.0 standard, which uses an http:// address scheme
the 1.1 standard, which uses an ipp:// address scheme
Example using a
Host Name
in the 1.0 Standard:
If “axisps” is the host name of the print server, "631" is the port number
and "LPT1" is the local printer port name, then the syntax of the address
scheme will be http://axisps:631/LPT1 in the 1.0 standard.
Example using an
IP Address
in the 1.1 Standard:
If “171.16.5.218” is the IP address of the print server and "LPT1" is the
local printer port name, then the syntax of the address scheme will be
ipp://171.16.5.218/LPT1 in the 1.1 standard.
IPP User Requirements
The IPP protocol does not require any special configuration of the AXIS
5570e/AXIS 5670e, the IPP function is automatically activated when you
install your print server.
IPP is platform independent and functional in Windows (NT, 98, Me and
2000/XP/2003), Macintosh, NetWare and UNIX/Linux.
Firewall
Considerations with
IPP
How to Print from
Windows 98
If there are one or more firewalls between the IPP client and the server,
you may have to make some changes to the firewall configuration. IPP
uses TCP Port 631 for printing, so any firewalls between client and server
must be configured to allow bi-directional traffic on that port. Please
consult your network administrator if you think any configuration
changes are necessary.
Before you print to an IPP printer you will need to know:
the address of the print server. The address contains the IP address or
host name of the print server and the printer port name.
• the brand and type of the printer in order to install the appropriate
printer driver.
If your destination printer does not exist in your Printer name list, you
need to add it. Adding an IPP printer to your printer list is described
below.
•
AXIS 5570e / AXIS 5670e User’s Manual
147
Configuration Possibilities
1. Select the IPP printer to which you want to send your document. Choose
the destination printer from the Printer name field (in File | Print).
2. When you press Print, the print job is sent over the Internet to the AXIS
5570e/AXIS 5670e, which then forwards the print job to the destination
printer.
3. The recipient of the print job can collect the print job at the destination
printer.
Adding an IPP Printer
to your Printer List in
Windows 98
1. Install the IPP client for Windows 98 on your computer. This IPP client
can be downloaded from the Microsoft Web site.
2. Open Start | Settings | Printers.
3. Choose Add Printer, then Network Printer.
4. In the Printer field in the Connect to Printers window, write the address
of the destination printer.
(Example: http://171.16.5.218:631/USB1)
5. Select the appropriate printer driver corresponding to the destination
printer.
6. Specify a name for the printer you wish to add to your printer list. Click
Finish. The destination printer will be added to your printer list and you are
ready to print using IPP.
How to Print from
Windows NT:
Before you print to an IPP printer you will need to know:
the address of the print server. The address contains the IP address or
host name of the print server and the printer port name.
• the brand and type of the printer in order to install the appropriate
printer driver.
1. First you need to select the IPP printer to which you want to send your
document. Select the destination printer from your Printer Name list (in
File | Print | Printer Setup).
•
The printer name will begin with a URL: http://...
If your destination printer does not exist in your Printer Name list,
you need to add it. Adding an IPP printer to your printer list is
described below.
2. When you press Print, the print job is sent over the Internet/WAN to the AXIS
5570e/AXIS 5670e, which then forwards the print job to the destination
printer.
3. The recipient of the print job can collect the print job at the destination
printer.
Adding an IPP Printer
to your Printer List in
Windows NT
1. Install the Internet Printer Connection software from Hewlett Packard
(can be downloaded from the Hewlett Packard Web site) on your
computer.
2. Open Start | Settings | Printers.
148
AXIS 5570e / AXIS 5670e User’s Manual
Configuration Possibilities
3. Choose Add Printer. The Add Printer Wizard will start.
4. Next, the Wizard will ask you if you want to install on My Computer or on
a Network print server. Choose My Computer and click Next.
5. In the Available Ports window, click Add Port:
6. The Printer Ports dialog will appear, showing a list of Available Printer
Ports.
AXIS 5570e / AXIS 5670e User’s Manual
149
Configuration Possibilities
7. Choose The HP Internet Printer Connection Port and click New Port.
8. The HP Internet Printer Connection will start. Click Next.
9. In the IP Address, Host Name or URL field, type the address of the AXIS
5570e/AXIS 5670e to which the destination printer is connected. The URL
will automatically appear in the Port Name field as well:
Example:
http://171.16.5.218:631/LPT1 if you want to address the parallel port or
http://171.16.5.218:631/USB1 to address the USB port.
Click Next.
10. The Wizard will confirm the information you have entered. Click Finish to
complete the installation and go back to the Available Ports list.
11. The IPP printer port list is now available in the Available Ports list. Click Next.
12. Next, choose a suitable driver for the destination printer and install it. Click
Next
.
150
AXIS 5570e / AXIS 5670e User’s Manual
Configuration Possibilities
13. You will be asked if you want the newly added printer to be your default
printer and if you want to share the printer on your network with other
users. Choose the alternatives that suit your printing needs and click Finish
to complete the installation.
14. The new printer will appear in your Printer window. You are now ready to
start printing using IPP.
How to Print from
Windows 2000/XP
Before you print to an IPP printer you will need to know:
the address of the print server. The address contains the IP address or
host name of the print server and the printer port name.
• the brand and type of the printer in order to install the appropriate
printer driver.
1. Select the IPP printer to which you want to send your document. Choose
the destination printer from the Select Printer field (in File | Print).
•
If your destination printer does not exist in your Select Printer list,
you need to add it. Adding an IPP printer to your printer list is
described below.
2. When you press Print, the print job is sent over the Internet to the AXIS
5570e/AXIS 5670e, which then forwards the print job to the destination
printer.
3. The recipient of the print job can collect the print job at the destination
printer.
Adding an IPP Printer
to your Printer List in
Windows 2000/XP
1. Choose File | Print from the document you wish to print.
2. In the Select Printer field, click the Add Printer icon. The Add Printer Wizard
will start. Click Next.
3. The Wizard will ask you if you want to install a local printer or a network
printer. Choose Network Printer and click Next.
AXIS 5570e / AXIS 5670e User’s Manual
151
Configuration Possibilities
4. Enter the printer address in the URL field.
Example:
http://171.16.5.218:631/LPT1 if you want to address the parallel port or
http://171.16.5.218:631/USB1 to address the USB port.
Click Next.
5. If you do not have a driver corresponding to the destination printer installed
on your computer, the Wizard will prompt you to install one. Click OK.
6. The Installation Wizard will ask you to select a printer driver corresponding
to the destination printer. Select the printer driver from the list and click OK.
7. The Wizard will ask you if you want the printer to be your default destination
printer. Make your choice and click Next to complete the Add Printer Wizard
installation.
152
AXIS 5570e / AXIS 5670e User’s Manual
Configuration Possibilities
8. The new printer is added to your Select Printer window:
9. You are now ready to print using IPP: specify your new destination printer
from the printer list and click Print.
AXIS 5570e / AXIS 5670e User’s Manual
153
Configuration Possibilities
Logical Printers for Customized Printing
The AXIS 5570e/AXIS 5670e has a powerful facility for altering the print
data. This means that your desired print format can be realized on any
type of printer. The following actions can be invoked from the print
server:
• The character set can be changed to suit the printer
• Strings can be added before and after the print data
• Strings within the print data can be substituted
• ASCII to PostScript conversion
• Redirection of print data to another printer if the printer is busy
• Hex Dump mode to assist with printing problems
• See Digital Copier Support, on page 202.
If any of these actions are required, a Logical Printer is used to change the
print data before being sent to the printer port. There are eight logical
printers (PR1-PR8) that can be set up to filter the print data.
Each logical printer can be set via the print server’s internal Web pages:
Open a Web browser, enter the IP address of the print server in the
Location/Address field and select Admin | Logical Printers.
The logical printers can also be set up by editing the config file. See
“Editing the config file” on page 135.
Notes:
• The examples in this section describe how you can configure the available logical printers
using a standard Web browser. If you want to set them directly by editing the config file,
just enter the values for the corresponding parameters.
• The examples should only be viewed as suggestions how to configure the logical printers.
You should, of course, configure them according to the needs of your network.
• In the Parameter List chapter of this manual, you can find a complete list of the AXIS
5570e/AXIS 5670e parameters.
Character Set
Conversion
A common problem in a multiple host environment is that different hosts
use different ASCII character sets. As a result of this, language specific
characters (such as å ü ô ñ) are sometimes printed incorrectly.
The AXIS 5570e/AXIS 5670e solution to this problem is to assign a
character set conversion filter to a logical printer, and then link that
logical printer to the host causing the problem.
You select your desired conversion filter by setting the Character Set
Conversion (PRx_CSET.) parameter. The output from the conversion filter
is always IBM PC Set 2 (Code Page 437), and this is the character set the
printer must be set up for.
154
AXIS 5570e / AXIS 5670e User’s Manual
Configuration Possibilities
Example:
Your network contains a host using the character set ISO 8859-2 and a host using the
character set DEC.
In order to direct print jobs to the printer connected to the AXIS
5570e/AXIS 5670e, you should assign the host to a separate logical
printer, and install a character set conversion filter.
Follow the instructions below to change the conversion filter (USB1 is
used as an examlpe here):
1. From the print server’s internal Web page, select Admin | Logical
Printers.
2. Select the PR1 tab.
3. Set the parameter Physical Port to USB1.
4. Set the parameter Character Set Conversion to ISO>IBM.
5. Click the OK button.
6. Select the PR2 tab.
7. Set the parameter Physical Port to USB1.
8. Set the parameter Character Set Conversion to DEC>IBM.
9. Click the OK button.
The ISO 8859-2 printer data that is sent to logical printer PR1 converts to
IBM PC Set 2 and is printed on USB1. Similarly, the DEC printer data that
is sent to logical printer PR2 converts to IBM PC Set 2 and is printed on
USB1.
Adding Strings Before
and After Print Jobs
These string functions provide a way to send printer control commands
before and after each print job. They may be specified individually for
each logical printer.
All strings are entered as hexadecimal byte values.
Example:
Assume that the logical printer PR5 is configured as a PostScript printer and that you want to
append the PostScript End of File character (hex 04) after each print job.
Follow the instructions below to add a string after the print job:
1. From the print server’s internal Web page, select Admin | Logical
Printers.
2. Select the PR5 tab.
3. Enter the string 04 in the String After Print Job text field.
4. Click the OK button.
AXIS 5570e / AXIS 5670e User’s Manual
155
Configuration Possibilities
Example:
You have an HP LaserJet printer with dual trays, and want to print on pre-printed forms when
using the logical printer PR4. The standard forms are taken from the lower tray, and the preprinted forms are taken from the upper tray. The string before print job should contain the
command to select the upper tray: EC&l1H (hex 1B 26 6C 31 48). The string after print
job should contain the command to select the lower tray: EC&l4H
(hex 1B 26 6C 34 48).
Follow the instructions below to add strings before and after the print job:
1. From the print server’s internal Web page, select Admin | Logical
Printers.
2. Select the PR4 tab.
3. Enter the string 1B 26 6C 31 48 in the String Before Print Job text field.
4. Enter the string 1B 26 6C 34 48 in the String After Print Job text field.
5. Click the OK button.
String Substitutions
The string substitution function performs search and replace operations
on the print data. The primary application is to replace printer control
commands. Up to twenty string substitutions may be specified
individually for each logical printer.
All strings must be entered as hexadecimal byte values, and each match
and substitute string must be preceded by a count byte.
You substitute command strings by editing the String Substitutions
(PRx_STR.) parameter.
Example:
Assume that you want to replace the UNIX/Linux New Line (hex 0A) with an Carriage
Return/Line Feed (hex 0D 0A) for logical printer PR1.
Follow the instructions below to substitute command strings:
1. From the print server’s internal Web page, select Admin | Logical
Printers.
2. Select the PR1 Web page.
3. Enter the string 01 0A 02 0D 0A in the String Substitutions text field.
Hex Code
Explanation
01
length of the string you want to replace
0A
the string you want to replace
02
length of the substitute string
0D 0A
the substitute string
4. Click the OK button.
This conversion is the default setting for logical printers PR5 through
PR8.
156
AXIS 5570e / AXIS 5670e User’s Manual
Configuration Possibilities
Example:
Assume that you want to replace the UNIX/Linux New Line (hex 0A) with an Carriage
Return/Line Feed (hex 0D 0A), and the printer command ECG1 (hex 1B 47 31) with
E Y (hex 1B 59) for logical printer PR2.
C
Follow the instructions below to substitute command strings:
1. From the print server’s internal Web page, select Admin | Logical
Printers.
2. Select the PR2 tab.
3. Enter the string 01 0A 02 0D 0A 03 1B 47 31 02 1B 59 in the String
Substitutions text field.
Hex code
Explanation
01
length of the UNIX/Linux New Line command
0A
the UNIX/Linux New Line command
02
length of the Carriage Return/Line Feed command
0D 0A
the Carriage Return/Line Feed command
03
length of the printer command to replace
1B 47 31
the printer command to replace
02
length of the new printer command
1B 59
the new printer command
Click the OK button.
Note:
Extensive use of string substitutions will naturally decrease the throughput rate of the AXIS
5570e/AXIS 5670e.
ASCII to Postscript
Conversion
The AXIS 5570e/AXIS 5670e logical printers can translate ASCII print
data into PostScript format. This makes it possible to print on a PostScript
printer from a host that does not support PostScript. The conversion is
selected by activating a filter that converts ASCII data into Postscript.
This filter can be activated individually for each logical printer.
Activate your desired filter by setting the Printer Language Translation
(PRx_FILT.) parameter.
Example:
Follow the instructions below to convert ASCII print data to PostScript for
logical printer PR2:
1. From the print server’s internal Web page, select Admin | Logical
Printers.
2. Select the PR2 tab.
3. Set the Printer Language Translation parameter to POSTSCR.
4. Click the OK button.
If you select the parameter value AUTO_PS, the print data for every print
AXIS 5570e / AXIS 5670e User’s Manual
157
Configuration Possibilities
job is searched and if any ASCII data is found, it is translated into
PostScript. This setting is recommended if you are not sure if the print
data is ASCII or PostScript.
PostScript Settings
When a logical printer is set for PostScript conversion, you must specify
the following:
• page size
• page orientation
• page format
• which font to use
The default page size is A4 and the default page orientation is Portrait,
while the page format parameters are as follows:
Page Format Parameter
Default Value
Lines per page (MPL)
66
Comment
Characters per line (MPP)
0
0 = disable line wrap
Characters per inch (CPI)
100
100 = 10 char per inch
Lines per inch (LPI)
60
60 = 6 lines per inch
Left margin (LM)
30
30 = 3.0 mm
Top margin (TM)
50
50 = 5.0 mm
The PostScript font can be any font that is installed in the printer. If no
font is specified, Courier will be used.
Example:
Follow the instructions below to set the PostScript parameters for logical
printer PR2:
1. From the print server’s internal Web page, select Admin | Logical
Printers.
2. Select the PR2 tab.
3. Set the Printer Language Translation parameter to POSTSCR.
4. Set the PostScript Page Size parameter to LETTER.
5. Set the PostScript Page Orientation parameter to LANDS.
6. Enter the string 48 0 120 60 30 50 in the PostScript Page Format text field.
Hex code
Explanation
48
48 lines per page
0
disable line wrap
120
120 = 12 characters per inch
60
60 = 6 lines per inch
30
30 = 3 mm left margin
50
50 = 5 mm top margin
7. Enter the string Helvetica in the PostScript Font text field.
8. Click the OK button.
158
AXIS 5570e / AXIS 5670e User’s Manual
Configuration Possibilities
Redirecting Print Jobs
when a Printer is Busy
If print data is received for a printer that is already busy, the host
normally must wait. However, with a two-port print server it is possible to
use a logical printer to redirect the print data to another logical printer
when the target printer is busy. If the second printer is also busy, the host
must wait until the target printer is ready.
Example:
Follow the instructions below to redirect PR1 print jobs to PR3, when the
printer assigned to PR1 is busy (USB1 and LPT2 are used as examples
here):
1. From the print server’s internal Web page, select Admin | Logical
Printers.
2. Select the PR1 tab.
3. Set the Physical Port parameter to USB1.
1. Set the Secondary Printer parameter to PR3.
2. Set the Wait On Busy parameter to NO.
3. Click the OK button.
4. Select Admin | Logical Printers and the PR3 tab.
5. Set the Physical Port parameter to LPT2.
6. Click the OK button.
Notes:
• The two printers must use the same printer driver.
• Logical Printer redirection cannot be nested. If PR3 is redirected to another logical printer,
the print job will not be redirected if PR3 is busy.
• If both printers are busy, the print job will be printed on the printer that first finishes its
active print job.
Read Back of
information
Example:
The AXIS 5570e/AXIS 5670e support bi-directional printing. The
information from the printer is read back on the parallel port when the
parameter Read Back Port (PRx_IN.) has the default setting of AUTO.
However, it is required that the printer also supports bi-directional
printing. Please refer to your printer documentation for further details
regarding bi-directional printing support.
Follow the instructions below to disable the bi-directional communication
for logical printer PR1:
1. From the print server’s internal Web page, select Admin | Logical
Printers.
2. Select the PR1 tab.
3. Set the Read Back Port parameter to NONE.
4. Click the OK button.
AXIS 5570e / AXIS 5670e User’s Manual
159
Configuration Possibilities
Debugging using the
Hex Dump Mode
Example:
When hex dump mode is enabled, the print data is printed as hexadecimal
byte values rather than characters; printer control commands are also
printed as hex values. This allows you to inspect what control and print
characters are actually being sent to the printer, which is a useful
debugging facility for more difficult printing problems.
Follow the instructions below to enable the hex dump mode for PR3:
1. From the print server’s internal Web page, select Admin | Logical
Printers.
2. Select the PR3 tab.
3. Set the Hex Dump Mode Enabled radio button to YES.
4. Click OK.
Note:
The page length for hex dump printouts is determined by the lines per page value of the
PostScript page format parameter.
160
AXIS 5570e / AXIS 5670e User’s Manual
Configuration Possibilities
Network Speed
With the Network Speed parameter you can manually specify the speed at
which you will send and receive network packages. You can change the
Network Speed setting to correspond to the type of network you are using
(10 or 100 Mbit).
To change the Network Speed in an Ethernet network, log in to the print
server’s internal Web pages and click Admin | General Settings =>
Change. From here, you have the option of setting the network speed to:
Network Speed
Comment
AUTO_SENSE
This is the default value where the print server detects which speed is optimal for each network package you transfer.
10_HALF__DX
10 Half Duplex
10_FULL_DX
10 Full Duplex
100_HALF_DX
100 Half Duplex
100_FULL_DX
100 Full Duplex
The default Network Speed value is AUTO_SENSE, which is the correct
option for the majority of users.
If you choose a faulty Network Speed option for your network, you may
loose contact with the print server.
To reset the Network Speed parameter to AUTO_SENSE, you will have to
reboot the print server (disconnect and then re-connect the external
power supply).
AXIS 5570e / AXIS 5670e User’s Manual
161
Configuration Possibilities
NetWare Packet Signature Levels
NetWare Packet Signatures protect servers and clients using the NCP
(NetWare Core Protocol) services and prevent packet forgery by requiring
the server and the client to sign each NCP packet.
Server Levels
Server packet signature levels are assigned by a new SET parameter:
SET NCP PACKET SIGNATURE OPTION = n
Key to Server Levels
0
1 (default)
2
3
Print Server Levels
Explanation
Server does not sign packets (regardless of the print server level)
Server signs packets only if the print server requests it (print
server level is 2 or higher)
Server signs packets if the print server is capable of signing
(print server level is 1 or higher)
Server signs packets and requires the print server to sign packets
(or logging in will fail)
Print server signature levels are assigned by a new NET.CFG parameter
SIGNATURE LEVEL = n
Key to Print Server Levels
0
1 (default)
2
3
Explanation
Print server does not sign packets
Print server signs packets only if the server requests it (server
option is 2 or higher)
Print server signs packets if the server is capable of signing
(server option is 1 or higher)
Print server signs packets and requires the server to sign packets
(or logging in will fail)
Regardless of server level, the AXIS print server has the capability to log
in in Print Server Mode since it supports NCP Packet Level 3 (which is the
most restrictive).
These procedures are taken care of automatically. There are no
configurable parameters in the Print Server for choosing the NCP Packet
Signature Level. The AXIS print server adapts itself to the Server Level.
Flash Loading of Firmware over the Web
The firmware can easily be upgraded, since flash loading over the Web is
possible from the print server’s internal Web pages. Client software is not
needed to upgrade the firmware. See Upgrading the Firmware, on page
169.
162
AXIS 5570e / AXIS 5670e User’s Manual
Configuration Possibilities
TCP/IP Restrictions
In a new and unconfigured Axis Network Print Server any user is allowed
to send TCP/IP print jobs. Using a restriction list you can reject TCP/IP
printing from specified IP addresses.
Enabling TCP/IP
Restrictions
In the print server’s Web interface, select Admin | Network Settings |
Detailed View | TCP/IP Printing.
Print jobs from IP addresses specified in the TCP printing restriction list
will be rejected. Comma delimited IP addresses as well as ranges of IP
addresses can be entered.
Examples:
192.168.0.10 will reject print jobs from IP address 192.168.0.10.
192.168.0.12, 192.168.0.32 will reject print jobs from IP addresses
192.168.0.12 and 192.168.0.32.
192.168.0.40-192.168.0.79 will reject print jobs from IP addresses
within the range 192.168.0.40 — 192.168.0.79.
Disabling TCP/IP
Restrictions
Empty the TCP printing restriction list to remove the restrictions. This is
the default setting.
AXIS 5570e / AXIS 5670e User’s Manual
163
Configuration Possibilities
Enabling Secure Web Services — SSL/TLS
In a new and unconfigured AXIS 5570e/AXIS 5670e, SSL/TLS is disabled.
Certificates
To use SSL/TLS you have to create or obtain a digital certificate. There are
two kinds of certificates: self-signed certificates and third party
certificates.
•
•
Self-signed certificates are less secure but normally they are sufficiently
secure for small networks with no public access. You generate such a
certificate yourself and there are no fees to pay.
For large networks and for networks with public access, third party
certificates from a trusted source are normally used. You obtain them
for a yearly fee from a Certificate Authority (CA).
Among other things, a certificate gives information about which domain
it is issued for, its validity and the name of issuer. With SSL/TLS enabled,
the installed certificate authenticates the print server to the client and all
information exchanged between them will be encrypted.
Enabling SSL via the
Web Interface
You enable the print server’s secure Web services through its internal
Web pages. If you have a valid certificate loaded, select Admin | Network
Settings | Detailed View | TCP/IP Network and set the HTTPS Enabled
parameter to Yes.
If you do not have a valid certificate loaded, select Admin | Security
Settings and click Create.
Decide whether you want to generate a self-signed certificate or if you
want to generate a certificate request.
Generating a SelfSigned Certificate
Select the Generate Self-Signed Certificate radio button and click Next.
Enter the data asked for:
•
•
•
•
•
•
•
•
Country Name: Example: US
State or Province Name: Example: California
Locality Name: Example: Los Angeles
Organization Name: Example: Printers Inc
Organizational Unit Name: Example: Sales Dept
Common Name*: Example: [email protected]
Current Date (yyyy/mm/dd): Example: 2004/09/28
Validity Duration (in days): Example: 365
* Common Name denotes the name given to the print server in the network. If you do
not have a DNS server on your network, you must include the domain name, e. g.
[email protected]
Click Finish and the print server will generate a public/private key pair as
well as the self-signed certificate itself (this process will take a few
minutes) and store these data in the print server. When the certificate is
generated, the print server automatically loads it into your present
164
AXIS 5570e / AXIS 5670e User’s Manual
Configuration Possibilities
browser session. The browser reports the new state by changing into https
mode. In the browser’s Security Alert box, select View Certificate and
Install Certificate. Follow the instructions of the Install Certificate
Wizard.
Generating a
Certificate Request
Select the Generate Certificate Request radio button and click Next.
Enter the data asked for:
•
•
•
•
•
•
•
•
Country Name: Example: US
State or Province Name: Example: California
Locality Name: Example: Los Angeles
Organization Name: Example: Printers Inc
Organizational Unit Name: Example: Sales Dept
Common Name*: Example: [email protected]
Current Date (yyyy/mm/dd): Example: 2004/09/28
Validity Duration (in days): Example: 365
* Common Name denotes the name given to the print server in the network. If you do
not have a DNS server on your network, you must include the domain name, e. g.
[email protected]
Click Finish.
Now the print server will generate a public/private key pair and a PEMencoded Certificate Request, called cert.pem. Click Save, Save this file to
disk and Save.
Send this Certificate Request to your Certificate Authority for their
signature.
Importing a
Certificate
Accessing the Print
Server’s Web pages
over https://
When you receive the PEM-encoded certificate from your Certificate
Authority, open the print server’s Web interface and select Admin |
Security Settings. Click Import and follow the instructions on the screen.
Whenever SSL/TLS is enabled, you can only reach the print server’s Web
interface through the secure services. The unsecure way via http:// is
closed and now you have to address the print server’s Web interface in
the secure way, i.e. via https://.
AXIS 5570e / AXIS 5670e User’s Manual
165
Configuration Possibilities
Disabling Protocols
To further increase security, you must disable protocols that are
considered insecure;
•
FTP (used by AXIS ThinWizard. If FTP is disabled, AXIS ThinWizard can
not function properly.)
• Telnet
• Auto-IP
• DHCP
• BOOTP
• Remote Config (used by AXIS NetPilot)
• SNMP Configuration (also used by AXIS ThinWizard. Note that if SNMP
is disabled, AXIS ThinWizard can not function properly.)
To disable these protocols, go to Admin | Security Settings | Protocol
Settings | Detailed View and mark the check boxes. Click OK to finish.
Only enabled protocols will be visible from this view!
To enable these protocols, select Admin | Network Settings | Detailed
View | TCP/IP Network for FTP, Telnet, Auto-IP, DHCP and BOOTP.
Remote Config is enabled via Admin | General Settings | RConfig
Support.
Important:
To ensure maximum security, it is highly recommended that you change your Administrator
password after generating a certificate and disabling insecure protocols! This is done from
Admin | General Settings | Change => | General | Root Password.
Checking
SSL/TLS Status
To check SSL/TLS status, open the print server’s Web interface and select
Admin | Network Settings | Detailed View | TCP/IP Network to see if the
HTTPS Enabled parameter is set to Yes or No.
To View a Certificate
To view a Certificate, open the print server’s Web interface, select Admin
| Security Settings and click View next to the Certificate.
To Delete a Certificate
To delete a Certificate, open the print server’s Web interface, select Admin
| Security Settings and click Delete next to the Certificate.
166
AXIS 5570e / AXIS 5670e User’s Manual
Configuration Possibilities
Enabling the SNMP3 Protocol
Invoke the print server’s Web interface to enable the SNMPv3 protocol.
1. Select Admin | Network Settings | Detailed View | TCP/IP Network and
ensure that HTTPS Enabled is set to yes to guarantee a secure
configuration.
Note: You must have a valid certificate loaded to be able to enable HTTPS.
See “Enabling SSL via the Web Interface” on page 164.
2. Select Admin | Network Settings | Detailed View | SNMP and set SNMPv3
Enabled to yes.
3. Create an initial user by entering two new passwords: one authentication
password and one privacy password. Each password must consist of at least
8 characters.
4. Click the Create initial user button.
Now your print server is ready to accept communication according to the
SNMPv3 protocol. For further management you will need an SNMPv3
management application; you use this application to configure the print
server, to create new user accounts and to control access to it. Also see
“Accessing the Print Server’s Web pages over https://” on page 165.
To Update the Initial
User
To update the initial user, select Admin | Network Settings | Detailed View
| SNMP, enter the two passwords (one for authentication and one for privacy)
and click the Update initial user button.
AXIS 5570e / AXIS 5670e User’s Manual
167
Configuration Possibilities
Overriding Port Status
Some USB printers do not deliver correct port status to the print server
(for instance always reporting printer off-line even if the printer is online). If you set the Override Portstatus parameter to Yes, the print server
will ignore the port status. To set this parameter, select Admin | General
Settings | USB1 from the print server’s Web interface.
168
AXIS 5570e / AXIS 5670e User’s Manual
Upgrading the Firmware
Section 13
Upgrading the Firmware
Upgrading the Firmware
You can upgrade the AXIS 5570e/AXIS 5670e firmware using one of the
following methods:
•
•
•
AXIS ThinWizard (TCP/IP)
From the print server’s internal Web pages (TCP/IP)
FTP (TCP/IP)
Note:
Updating instructions are supplied with the firmware release notes.
Upgrading from the
Print Server’s Internal
Web Pages
Follow these instructions to upgrade the firmware of your print server
from its internal Web pages (flash loading over the Web):
1. Open your Web browser, enter the IP address of your print server and
press Enter. (See “Using a Web Browser for Print Server Management” on
page 128 for detailed instructions on accessing your Axis print server on
the Web).
2. From the Admin mode, click the Firmware Upgrade button. From here you
can upgrade your print server with the latest available firmware.
Upgrading using
AXIS ThinWizard
AXIS ThinWizard 3.0 is a tool that enables batch upgrading of several
print servers and can be used for upgrading the print server’s firmware in
TCP/IP networks.
Follow the instructions below to upgrade your print servers using AXIS
ThinWizard:
1. Log in to AXIS Thin Wizard.
2. Open the Network Group that contains the print server to be upgraded.
3. Click the Firmware button. The Firmware Wizard starts.
4. Browse through the upgrading tips and click Next > when you are done.
Select Latest Available Version. Click Next >.
5. Select the servers you want to upgrade, by checking the correct upgrade
boxes. Click Next >.
6. Enter the default User ID and Password of the servers you selected in the
previous step. Select whether you want AXIS ThinWizard to verify the
password immediately or when the upgrading job has started, by checking
the appropriate box. Click Next >.
AXIS 5570e / AXIS 5670e User’s Manual
169
Upgrading the Firmware
7. If you do not have a default password, just click Next >. If some of your
servers use a different User ID or Password than the default entries, they will
be displayed in the Remaining servers list. Enter the User ID and Password
for each individual server. Click Next >.
8. Name the upgrade job. This is optional, so you can leave the field blank if
you want. Click the Start button to start the upgrading job.
9. You can view the progress of the job in the Event Log.
Refer to “Using AXIS ThinWizard for Print Server Management” on page
133 for more information about AXIS ThinWizard.
Upgrading using FTP
To upgrade over the network using FTP you will need a file with the new
print server firmware. The name of this file is in the form
product_version.bin.
Ensure that FTP Enabled is set to yes. To check this parameter, browse to
the print server and select Admin | Network Settings | Detailed View |
TCP/IP Network.
Caution!
Be careful not to interrupt the file transfer. If the transfer is interrupted, the print server may
have to be re-initialized by your dealer.
The objective of this example is to upgrade a print server to firmware
version 7.00.
The description below from a typical Windows session uses the following
examples:
•
•
•
•
170
Print server model: AXIS 5570e
IP address of print server: 10.13.4.105
New firmware version name: 5570e_7_00.bin
Location of firmware and upgrade procedure: c:\Axis
AXIS 5570e / AXIS 5670e User’s Manual
Upgrading the Firmware
1. From www.axis.com, download the firmware and save it to a new
directory on your computer, e.g. c:\Axis (if the directory does not exist,
create it).
2. Open a command prompt from Start => Run. The Run window will appear.
Type cmd and click OK. (Windows 98: Type command and click OK.) The DOS
Command Prompt window will open.
3. Make sure you are working from the correct directory:
type cd c:\Axis and press Enter.
4. Connect to the print server using ftp:
type ftp 10.13.4.105 followed by Enter.
(Example using print server IP address 10.13.4.105)
5. Enter the user name, the default user is root. Press Enter. If the default
password has been changed then it must also be entered. When you enter
the password, it will not be echoed to the screen, nor will the cursor move.
6. Change to binary mode transfer.
Type bin hash (or binary hash) and press Enter.
7. Use the put command to upload the upgrade file to the flash location:
(Example using firmware named 5570e_7_00.bin):
Type put 5570e_7_00.bin FLASH followed by Enter. (Note that FLASH is
written in capital letters!) A stream of hash (#) marks will appear.
Wait 30 seconds... You will receive a message stating Transfer complete.
Flash programming finished OK. The print server will restart in five seconds
running the new software.
When you see a new ftp prompt the procedure has been completed
successfully.
8. Type bye followed by Enter to end the ftp session.
Obtaining the Software
You can obtain all the print server firmware as well as the latest utility
software from the following locations:
•
•
http://www.axis.com
your local dealer
AXIS 5570e / AXIS 5670e User’s Manual
171
SNA Parameter Overview
Section 14
SNA Parameter Overview
This appendix provides summary information on the parameters that
control the basic operation of the SNA communication and the IBM
printer emulation. It also describes how these parameters may be
changed.
An overview of how parameters are mapped during the autoconfiguration process is also provided.
Refer to the Parameter List document on www.axis.com for a complete
description of the Axis Print server parameters.
Communication Parameters
In most environments, the basic communication parameters need to be
customized in order to establish a communication link to the host system.
This includes setting the Host MAC Address and Host Name parameters in
the Print Server. In this chapter you will find instructions on how to
update these parameters.
SNA Communications
Process
There are several parameters that control the basic operation of the SNA
communication, and IBM printer emulation. The diagram below shows
how they relate to the SNA printing process.
SNA Communication
Settings
IBM Printer
Settings
Printer Driver
Settings
Network
Printer
Device Emulation
MAC Address
Service Access Point
Node ID
Network Name
LU Name
CP Name
SNA Communication
Settings
IBM Printer Emulation
System Language
Paper Size
Page Orientation
IBM Printer
Settings
ASCII Printer Driver
Printer Driver
Settings
Network
Printer
Device Emulation
MAC Address
Service Access Point
Node ID
Network Name
LU Name
CP Name
IBM Printer Emulation
System Language
Paper Size
Page Orientation
ASCII Printer Driver
Schematic diagram displaying basic SNA operation and IBM printer emulation
172
AXIS 5570e / AXIS 5670e User’s Manual
SNA Parameter Overview
Parameter Summary
The following tables summarize SNA host communication parameters
that must be considered when installing the Axis Network Print Server.
The parameters are presented as:
•
•
•
Common Mainframe &
AS/400 Parameters
Common Mainframe and AS/400 parameters
Mainframe specific parameters
AS/400 specific parameters
Parameter
Name
Default
DEVICE_EMUL
Control Unit Device
Emulation
3174
Th DEVICE_EMUL parameter controls the Control Unit emulation mode. When set to 3174, the Print
Server will appear as a 3174 PU 2.0 node to the host. This mode may be used for both mainframe
and AS/400 environments.
When set to 5494, the Print Server will appear as a 5494 PU2.1 node to the host. This is the
recommended mode for the AS/400 environment. The 5494 mode cannot be used in the mainframe
environment.
H1_ADDR
Host MAC Address
FF FF FF FF FF FF
The H1_ADDR is the Host Ethernet/Token Ring MAC address. It is normally set to the MAC address of
the host.
When the Print Server is connected to the host through a gateway, this parameter should be set to
the MAC address of the gateway. For a directly attached AS/400 system, this value is found in the
"Line Description".
Automatic Link
Establishment
AUTODIAL
no
The AUTODIAL parameter controls whether the print server will automatically try to establish the
link when the print server is switched on, or if communication is lost.
When running 5494 CU mode, this parameter also controls whether Automatic Configuration should
be performed.
Mainframe Specific
Parameters
Parameter
Name
Default
NODE_ID
Node ID
E07xxxxx, where "xxxxx" are the last five digits of the print
server’s MAC address.
This is the SNA PU identification.
The first 3 digits is the IDBLK and the last five is the IDNUM.
When defining a VTAM Switched Major Node, this parameter should match the IDBLK and IDNUM
values specified in the PU definition.
Only Hexadecimal characters (0-9 and A-F) allowed.
AS/400 Specific
Parameters
Parameter
Name
Default
Emulation
NWORK_NAME
Network Name
APPN
5494 only
Description - This is the Print Server Network Name.
The value of this parameter is normally the same as the "Host Network Name", indicating that both
the Print Server and the AS/400 system are located on the same APPN network.
The Network Name may comprise the letters A-Z and/or numerals 0-9, but must begin with a letter.
The letters used should all be in UPPERCASE and a maximum of 8 characters are allowed.
LU_NAME
AXIS 5570e / AXIS 5670e User’s Manual
LU Name
Axxxxxxx
5494 only
173
SNA Parameter Overview
Parameter
Name
Default
Emulation
Description - Axxxxxxx, where "xxxxxxx" is the last 7 characters of the Axis Network Print Server
serial number, in reverse order, e.g.
if s.no. =
00 40 8C 1B 06 D4 the default LU Name =
A4D60B1C.
This will be the name of the APPC device and controller
created during auto-configuration
CP_NAME
(AXIS 570 only)
Control Point Name
Axxxxxxx
5494 only
Description - Axxxxxxx, where "xxxxxxx" is the last seven characters of the Print Server serial
number, in reverse order, i.e. a print server with serial number 00 40 8C 1B 06 D4 will have the
default CP Name A4D60B1C. This will be the name of the APPC controller created during autoconfiguration.
H1_NW_NAME
Host Network Name
APPN
5494 only.
H1_LU_NAME
Host LU Name
DEFAULT
5494 only
Updating parameters
This is most easily done from the internal Web pages of your Axis
Network Print Server. To set the parameters using a Web browser, you
first need to assign an IP address to the Axis Network Print Server. For
instructions on how to do this, refer to “Setting the IP Address” on page
16.
Alternatively, you can update the parameters via FTP, TFTP or by using
extended IBM printer emulation.
Using extended IBM printer emulation means setting up the Axis Network
Print Server by printing a file containing extended IBM emulation
commands to it after you have established communication with your IBM
host. The configuration is started by inserting the sequence %CONFIG+ in
your text. To protect your settings, a password must be provided. By
default, the password is pass. You may then set the parameter values
directly using the syntax shown below:
Syntax:
<Parameter name> = <value> [, <value>];
When all parameters have been set the SAVE command saves the settings
permanently. The %CONFIG- command resumes normal printing. In order
to maintain backward compatibility, some parameters must be preceded
by a %CONFIG++ command. See also The Parameter List, on page 216.
To set the parameters to their default values, enter the following in your
document and print it.
174
AXIS 5570e / AXIS 5670e User’s Manual
SNA Parameter Overview
%CONFIG+ password(If you have not changed the default
password (pass), the password is optional.)
PRDRIVER = PCL5;
%CONFIG++
NODE_SAP = 4;
H1_SAP = 4;
AUTODIAL = NO;
%CONFIG-PREMUL = 3816;
SYSL = 37;
BIN1 = LETTER, COR;
SAVE;
%CONFIG-
Changing
Parameters after
Auto-configuration
If you want to change some of the critical configuration parameters after
auto-configuration is completed, you should first set AUTODIAL to NO,
then remove all descriptions in the AS/400, and then change the
parameter(s) and set AUTODIAL to YES to initiate a new configuration
process.
Auto-configuration and Mapping
The configuration created in the AS/400 and the mapping to the Axis
Network Print Server as a result of the auto-configuration process is
illustrated by the figure below.
Configuration in the
AXIS 5470e
Configuration in the
AS/400
LU 6.2 conversation
APPC-controller
APPC-device
Logical mappings
RWS-controller
Logical Printer #1
Printer device #1
Logical Printer #2
Printer device #2
Logical Printer #3
Printer device #3
AXIS 5570e / AXIS 5670e User’s Manual
175
SNA Parameter Overview
Configuration in the
AXIS 5470e
Configuration in the
AS/400
LU 6.2 conversation
APPC-controller
APPC-device
Logical mappings
RWS-controller
Logical Printer #1
Printer device #1
Logical Printer #2
Printer device #2
Logical Printer #3
Printer device #3
Illustration of the configuration created in the AS/400 and the mapping to the Axis Network
Print Server as a result of the auto-configuration
Printer Device
Descriptions
Through auto-configuration, the APPC controller, APPC device, RWS
controller as well as printer device descriptions for the logical printers,
will be created automatically.
Controller and Device
Names
The names of the controllers and devices created in the AS/400 during
auto-configuration are by default the last 7 characters from the Axis
Network Print Server serial number in reverse order, preceded by the
letter "A".
For example, serial number "00408C180102" will result in APPCcontroller "A201081C", APPC-device "A201081C" and RWS-controller
"A2010RMT".
Printer devices will be named "A201PRT01", A201PRT02", A201PRT02"…
The designation "PRTnn" corresponds to the logical printers in the Print
Server, i.e. printer device "A201PRT01" will be mapped to Logical Printer
#1. By default, all Logical Printers are mapped to the Physical Port LPT1.
To customize the print server, proceed to the SNA Printing - 5494 Mode,
on page 22.
176
AXIS 5570e / AXIS 5670e User’s Manual
SNA Gateways
Section 15
Gateway
Configuration,
3174 CU mode
SNA Gateways
Some hints specific to SNA gateways are given below.
•
•
•
Pass-through gateway
Axis Network Print Server appears to a gateway as a Down Stream
Physical Unit (DSPU), with eight LUs, 1 to 8 (LU 1 may not be available).
Only gateways that communicate with DSPUs using SNA over LLC type
2 are supported.
There are basically two types of gateways that the Axis Network Print
Server can be attached to: pass-through gateways and concentrator
gateways, as described below.
Devices attached downstream to this type of gateway are completely
visible to the host. In other words, each DSPU will have a PU definition
on the host. Examples of pass-through gateways are IBM 3745
Communications Controller, IBM 3174 Establishment Controller, IBM
3172 LAN Interconnect Controller, etc.
You need to set up at least one PU and LU definition for each Axis
Network Print Server on the host, as described in the VTAM section.
When attaching an Axis Network Print Server to a remote pass-through
gateway, you need to set the mapping of SDLC or sub-channel address to
MAC address in the gateway.
Concentrator gateway,
general
A concentrator gateway typically behaves as a PU (or a few PUs) to the
host, even though a number of PUs may be available downstream. If it is
an SDLC or channel attached gateway, typically only one SDLC or subchannel address will be used. Examples of concentrator gateways are:
IBM Communications Manager/2 (OS/2), Novell NetWare for SAA
(NetWare 3.x), Microsoft SNA Server (Windows NT), etc.
When an Axis Network Print Server is attached to this type of gateway,
you can map the chosen Axis Network Print Server LU to any host LU you
like. This way, several print servers may be accessed through the same
gateway.
Pooling LUs may not be used for Axis Network Print Server.
Concentrator Gateway,
NetWare
This is an outline of the procedure for configuring to a Novell NetWare
for SAA v 2.0 Server. More information is provided in the ‘Suppor’t
section of www.axis.com
1. Customize the AUTOEXEC and STARTUP files on the server. Add the LOAD
statements for the LAN and WAN cards, the BTRIEVE database, and the
NetWare for SAA 2.0 Gateway
i.e. LOAD COMMEXEC and LOAD NWSAA.
2. Configure the Communication Executive (this and the following subjects are
done on a WorkStation).
AXIS 5570e / AXIS 5670e User’s Manual
177
SNA Gateways
3. Configure SNA Network ID. Either change the default value or let it stay on
default.
4. Configure Data Link Adapters. The configuration is done on the Data Link
Adapters Definitions screen by pressing insert for a new adapter config, then
you always enter the Logical adapter name, Link type, Logical adapter
number and Service status.
5. Configure PU and LUs. On the Configure PU Profile screen you can set
default LU attributes, starting dependent LU address, number of dependent
LUs, give CP a name, enable off-line test mode, status assignment of LUs
activated by host, status call host at workstation attach, status PU profile
start-up and logical adapter name. On the Configure Dependent LUs screen
you can set VTAM LU name, lock for a session, LU type and model and
preserve host session.
6. Assign LU Resources and Access Control Lists (ACLs). On the Configure
Dedicated LUs you can dedicate a LU to a person or device or group of
persons. This person(s) is described in the access control lists.
7. Configure Downstream PU. Choose Configure Downstream PUs and press
insert. Give it a name and fill in starting LU address or leave at default, type
in number of DownStream LUs and logical adapter name:
Configure Downstream PU Connection
Downstream PU name (CP name):
_____________________________DPUname
Starting downstream LU address: ___________________________2
Number of downstream LUs: _________________________________1
Logical adapter name: _____________________________________
The CSCON adds new parameters according to the adapter type you have
set. The resulting screen can look like this:
Netware Comm Services Config V2.0 Wednesday 1999 September 4
16.27
Configure LUs for Downstream PUs _______________Downstream
PU: AXIS5570e
DLU __Address __PU Profile __LU Address __LU Type __Model
__VTAM LU Name
002 __(0x02) ____SAA_MAIN ____15 (0x0F) __Printer
__________________ACP4
Concentrator gateway,
Microsoft
This is an outline of the procedure for configuring to a Microsoft SNA
Server. More information is provided in the Support section of the Axis
Web site at http://www.axis.com
1.
2.
3.
4.
Configure host connection.
Configure downstream connection.
Select host connection and assign one or more DownStream LUs to it.
Select downstream connection and associate the DownStream LUs (from
step 3) with that connection.
5. If necessary, reorder the DownStream LU numbers, that is, the LU numbers
used by the downstream system.
6. To connect multiple PUs (boxes) repeat steps 2-5.
178
AXIS 5570e / AXIS 5670e User’s Manual
Extended IBM Printer Emulation
Section 16
Extended IBM Printer Emulation
When printing from an IBM host, the Axis Network Print Server allows
you to make use of the following printer functions not found in standard
IBM printers:
• Configuration Mode
• Hex Transparency
• User Defined Strings
• String Substitutions
• Bar Codes
• Font Selection.
This appendix provides a brief overview of some of these functions.
Configuration Mode
The Configuration Mode provides a way to configure your Axis Network
Print Server from your IBM system. For more information see SNA
Parameter Overview, on page 172.
User Defined Strings
The User Definable Strings are a set of 256 programmable sequences. The
UDS are useful for storing long sequences, such as printer function
sequences, within the Axis Network Print Server. Each sequence can be
activated by inserting a short control command in your documents.
String Substitutions
The String Substitution function searches the output data stream for
specified sequences of AIC characters (Match Strings), and substitutes
them with other sequences (Substitute Strings). Up to 128 pairs of
Match/Substitute Strings may be defined.
AIC (AXIS Internal Codes) are listed in the AXIS Network Print Server Technical Reference.
Font Selection
Fonts can be selected directly by FGID (Extended Emulation commands or
SCS SFG commands) or indirectly by pitch SCS SCD/SPD commands.
Notes:
Hex Transparency
•
SFG control code is only supported by Twinax page printer emulations
•
Matrix printers only support a few fonts
The Transparency function allows you to send ASCII data to the printer
directly from the host application. The data may be Postscript, PCL, HPGL or any other language supported by the printer. This gives you access
to all the features of the connected printer from within the IBM
environment.
When the percent and less-than characters (%<) are received, the Axis
Network Print Server will switch to hex transparency mode. The following
AXIS 5570e / AXIS 5670e User’s Manual
179
Extended IBM Printer Emulation
data (given as hexadecimal byte values or quoted text) is passed directly
to the printer without any conversion. The hex transparency mode
continues until the greater-than and percent characters (>%) are received.
The following example shows how to embed HP-PCL ‘start underline’
(<ESC>&d0D) and ‘stop underline’ (<ESC>&d0@) commands in your
documents:
The word %<1B26643044>%underline%<1B266440>% is underlined.
You can also use %<1B,"&d0D">%quoted text%<1B,"&d0@">%
Resulting printout:
The word underline is underlined
You can also use quoted text.
Bar Codes
The bar code function provides easy access to a range of standard bar
code types resident in the Axis Network Print Server. Bar codes can only
be printed on PCL printers.
Before the bar codes can be printed, a bar code format has to be defined.
This format sets the type and size of the bar code to be printed. Up to 16
formats can be predefined. The definitions are made by setting up the
BAR parameter.
The BAR parameter takes several arguments, separated by commas, as
shown below:
BAR <number>=<type>,<width>,<height>,<text mode>,
<check mode>;
•
•
number is the bar code definition number in the range 0–15. This
number is used to refer to the definition when printing the bar code.
type is the predefined bar code type. Valid values are:
Value
Value
Description
Code 39
CODE128
Code 128
UPCA
UPC version A
INT2OF5
2 of 5 Interleaved
EAN8
EAN-8
EAN13
EAN-13
CODE39
180
Description
CODABAR
Codabar matrix
AXIS 5570e / AXIS 5670e User’s Manual
Extended IBM Printer Emulation
width is the bar code module width in 1/1000 inch. Valid range is 1 to
1000. The default value is 12.
• height is the bar code element height in 1/24 inch. Valid range is 1 to
500. The default value is 12.
• text mode selects if human readable text is printed under the bar code
or not. ‘YES’ or ‘ON’ will turn on text, ‘NO’ or ‘OFF’ will turn off text.
The default mode is ‘ON’.
• check mode selects if a check digit will be generated or not. ‘YES’ or
‘ON’ will generate a check digit, ‘NO’ or ‘OFF’ will not generate a check
digit. The default mode is ‘ON’. The check digit will always be generated
for bar code types UPCA, EAN8 and EAN13, regardless of the setting of
check mode.
To set up the BAR parameter, use the %CONFIG command in your
document. To print bar codes, bar code commands may be included
anywhere in your documents. They begin with ‘percent-slash’ (%/)
followed by the word BAR. Then follows the number of the bar code
definition to be used, a comma, and the sequence to be printed. The
command is ended by a semi-colon (;).
•
Setting up the bar code parameters and printing bar codes
%CONFIG+
BAR 0 = EAN8,12,4,ON;
BAR 1 = EAN8,12,8,ON;
SAVE;
%CONFIG%/BAR 0,"0123456"; %/BAR 1,"0123456";
Once the BAR parameter has been set up, you will only need to use the bar
code commands to print the bar codes
%/BAR 0,"0123456";
%/BAR 1,"0123456";
Resulting printout:
0123 4565
0123 4565
AXIS Cobra products
compatibility
The Axis Network Print Server supports a subset of the extended printer
emulation syntax of the AXIS Cobra products, including the bar codes
syntax. For more information, please refer to the AXIS Network Print
Server Technical Reference supplied on the AXIS Network Product CD.
AXIS 5570e / AXIS 5670e User’s Manual
181
IBM Fonts
Section 17
Font Selection,
Coax Printer
Emulations
IBM Fonts
Fonts can be indirectly selected by the IBM system using pitch selection
(CPI). In order to gain full access to the fonts the Axis Network Print
Server offers an alternative font selection command. Please note that
matrix printers only support a few fonts.
Font selection commands may be included anywhere in your documents.
They begin with ‘percent-slash’ (%/) followed by the word FONT and the
font number (Font Global Identifier, FGID). An optional point size value,
preceded by a comma, may be included. The command is ended by a
semi-colon (;).
The following example shows how to select the 10 CPI Courier (fixed
pitch) font.
%/FONT 11;This is 10 CPI Courier
Resulting printout:
This is 10 CPI Courier
Font Selection,
Twinax Printer
Emulations
Fonts are selected by a FGID (Font Global Identifier) and mapped to a
printer resident PCL font, selected to make a close match to the original
IBM font. The IBM to PCL font mapping is controlled by the Font
Definition Table. All entries in this table are fully editable, and you can
also add new entries.
Refer to DBCS Support, on page 197 for details on DBCS font types supported by the Axis
Network Print Server.
Available Fonts
The fixed pitch fonts are not scalable. If a Point Size is specified, it will be
used to compress or expand the character spacing. (%/FONT 11,105; will
compress the 10 CPI font to 10.5 CPI without changing the size of the
characters).
Pitch 5 CPI Fonts
Pitch 8 CPI Fonts
182
FGID
IBM Font Name
244
Courier 5
245
Courier Bold 5
266
Courier Bold 8
AXIS 5570e / AXIS 5670e User’s Manual
IBM Fonts
3
OCR-B
5
Orator
11
Courier 10
12
Prestige Pica
13
Artisan 10
18
Courier Italic 10
19
OCR-A
20
Pica
30
Math Symbol 10
38
Orator Bold
39
Gothic Bold 10
40
Gothic Text 10
41
Roman Text 10
42
Serif Text 10
43
Serif Italic 10
46
Courier Bold 10
60
Prestige Bold 10
FGID
IBM Font Name
66
Gothic Text 12
68
Gothic Italic 12
69
Gothic Bold 12
70
Serif Text 12
71
Serif Italic 12
72
Serif Bold 12
80
Math Symbol 12
84
Script
85
Courier 12
86
Prestige Elite
87
Letter Gothic 12
91
Light Italic 12
108
Courier Bold 12
110
Letter Gothic Bold
111
Prestige Elite Bold
112
Prestige Elite Italic
204
Gothic Text 13
221
Prestige 15
223
Courier 15
225
Math Symbol 15
229
Serif Text 15
230
Gothic Text 15
252
Courier 17
253
Courier Bold 17
254
Courier 17 (sub/super)
Pitch 18 CPI Fonts
258
Courier 18
Pitch 20 CPI Fonts
281
Gothic Text 20
Pitch 25 CPI Fonts
289
Gothic Text 25
Pitch 26.7 CPI Fonts
290
Gothic Text 27
Pitch 10 CPI Fonts
Pitch 12 CPI Fonts
Pitch 13.3 CPI Fonts
Pitch 15 CPI Fonts
Pitch 17 CPI Fonts
AXIS 5570e / AXIS 5670e User’s Manual
183
IBM Fonts
Proportional PSM Fonts
Proportional Typographic
Fonts (Fixed Point Size)
FGID
IBM Font Name
155
Boldface Italic
158
Modern
159
Boldface
160
Essay
162
Essay Italic
163
Essay Bold
173
Essay Light
175
Document
751
Sonoran-Serif 8-pt Roman Medium
1051
Sonoran-Serif 10-pt Roman Medium
1053
Sonoran-Serif 10-pt Roman Bold
1056
Sonoran-Serif 10-pt Roman Italic Medium
1351
Sonoran-Serif 12-pt Roman Medium
1653
Sonoran-Serif 16-pt Roman Bold
2103
Sonoran-Serif 24-pt Roman Bold
Proportional Typographic Fonts
(Scalable - User Defined FGIDs)
184
FGID
IBM Font Name
3840
CG Times
3841
CG Times Bold
3842
CG Times Italic
3843
CG Times Bold Italic
3844
CG Omega
3845
CG Omega Bold
3846
CG Omega Italic
3847
CG Omega Bold Italic
3848
Coronet
3849
Clarendon Condensed
3850
Univers Medium
3851
Univers Bold
3852
Univers Medium Italic
3853
Univers Bold Italic
3854
Univers Medium Condensed
3855
Univers Bold Condensed
3856
Univers Medium Condensed Italic
3857
Univers Bold Condensed Italic
3858
Antique Olive
3859
Antique Olive Bold
3860
Antique Olive Italic
3861
Garamond Antiqua
3862
Garamond Halbfett
AXIS 5570e / AXIS 5670e User’s Manual
IBM Fonts
Proportional Typographic Fonts
(Scalable - User Defined FGIDs)
Proportional Typographic Fonts
(Scalable Point Size)
(cont.)
Proportional Typographic Fonts
(Scalable Point Size)
AXIS 5570e / AXIS 5670e User’s Manual
3863
Garamond Kursiv
3864
Garamond Kursiv Halbfett
3865
Marigold
3866
Albertus Medium
3867
Albertus Extra Bold
3868
Arial
3869
Arial Bold
3870
Arial Italic
3871
Arial Bold Italic
3872
Times New
3873
Times New Bold
3874
Times New Italic
3875
Times New Bold Italic
3876
Symbol
3877
Wingdings
FGID
IBM Font Name
5687
Times Roman
5707
Times Roman Bold
5815
Times Roman Italic
5835
Times Roman Bold Italic
6199
Palatino
6219
Palatino Bold
6327
Palatino Italic
6347
Palatino Bold Italic
16951
Century Schoolbook
16971
Century Schoolbook Bold
17079
Century Schoolbook Italic
17099
Century Schoolbook Bold Italic
33335
Optima
33355
Optima Bold
33463
Optima Italic
33483
Optima Bold Italic
33591
Futura Book
33601
Futura Heavy
33719
Futura Book Italic
33729
Futura Heavy Italic
34103
Helvetica
34123
Helvetica Bold
34231
Helvetica Italic
34251
Helvetica Bold Italic
41783
Cursive
41803
Cursive Bold
41911
Cursive Italic
41931
Cursive Bold Italic
185
IBM Print Formatting
Section 18
IBM Print Formatting
This appendix provides general parameter information relating to nonIPDS IBM print formatting.
IBM Printer
Emulation
Coax Printer
Emulations
Mainframe
The following tables display the valid printer emulations that can be used
in coax and twinax printer emulations.
Parameter
PREMUL
Default
3816_cx
Printer
Emulation
Options
Printer Description
3812_cx
IBM 3812 model 2 non-IPDS, page printer
*3816_cx
IBM 3816 models 01A and 01D non-IPDS,
page printer with 5219 diskette
3287_cx
IBM 3287 model 2C, matrix printer
3268_cx
IBM 3268 model 2C, matrix printer
3262_cx
IBM 3262 models 3 and 13, matrix printer
4214_cx
IBM 4214 model 1 matrix printer
4224_cx
IBM 4224 model 2 non-IPDS, matrix printer
4230_cx
IBM 4230 model 201 matrix printer
Twinax Printer
Emulations
AS/400
Parameter
Name
PREMUL
System Languages
186
Default
3816_cx
Printer Emulation Options
Printer Description
3812_tx
IBM 3812 model 1 and 2 page
printer
3816_tx
IBM 3816 models 01S and 01D,
page printer with 5219 diskette
4214_tx
IBM 4214 model 2 matrix printer
5224_tx
IBM 5224 models 1 and 2, matrix
printer
5225_tx
IBM 5225 models 1 through 4,
matrix printer
5256_tx
IBM 5256 models 1 through 3,
matrix printer
4230_tx
IBM 4230 model 101 matrix
printer
5x27_002_TX_KS
5x27 002 Twinax printer: Korean
(KS)
5x27_002_ TX_KSSM
5x27 002 Twinax printer: Korean
(KSSM)
5x27_001_ TX
5x27 001 Twinax printer:
Japanese
5x27_005_TX
5x27 005 Twinax printer:
Chinese
The following tables describe the valid system languages that can be used
in coax and twinax mode.
AXIS 5570e / AXIS 5670e User’s Manual
IBM Print Formatting
Coax mode
Mainframe
Parameter
Name
SYSL
Default
37 US English
AXIS 5570e / AXIS 5670e User’s Manual
Value
Description
Value
User defined system language
*37
US English, Portuguese
Alternate and Canadian
Bilingual
833
256
International Set 1
836
Chinese
260
Canadian French
838
Thai
273
Austrian/German
870
East Europe
274
Belgian
871
Icelandic
275
Brazilian
875
Greek (GKB)
277
Danish/Norwegian
892
OCR-A
278
Swedish/Finnish
893
OCR-B
280
Italian
1026
Turkish (Primary)
281
Japanese English
1140
US English (Euro)
282
Portuguese
1141
Austrian German (Euro)
284
Spanish
1142
Danish/Norwegian (Euro)
285
UK English
1143
Swedish/Finnish (Euro)
286
Austrian/German Alternate
1144
Italian (Euro)
287
Danish/Norwegian Alternate
1145
Spanish (Euro)
288
Swedish/Finnish Alternate
1146
UK English (Euro)
289
Spanish Alternate
1147
French (Euro)
290
Japanese
1148
International Set 5 (Euro)
293
APL
1149
Icelandic
297
French
USER
User defined
340
OCR
361
International Typographic
423
Greek (GKB)
500
International set 5
Korean (Jamo)
187
IBM Print Formatting
Twinax mode
AS/400
Parameter
Name
SYSL
Default
37 US English
Value
Description
Value
User defined system language
37
US English, Portuguese Alternate
and Canadian Bilingual
281
Japanese English
256
New Spanish Word Processing
282
Portuguese
273
Austrian/German
284
Spanish and Spanish Speaking
274
Belgian
285
UK English
275
Brazilian
297
French Azerty
277
Danish/Norwegian
500
Internat. Set 5 & Swiss Bilingual
278
Swedish/Finnish
871
Icelandic
280
Italian
USER
Notes:
Page Formats
•
For other languages the USER language can be used and edited.
•
To find out which system language you are running type:
DSPSYSVAL SYSVAL(QCHRID) on the command line and press Enter. The Code
page value is the value of the system language (see the table above).
•
Visit the Axis Web site http://www.axis.com/ for more information on how to edit the character translation tables
You can configure the formats for each paper bin separately from the
Axis Network Print Server internal Web pages.
Click Admin | IBM Emulators | Detailed View for SCS/3270DS Common
Emulator Settings. Select the Page Format tab to configure the
parameters described below. Click OK at the bottom of the page to save
your settings to the print server.
Paper Size
The parameters take two values, orientation and paper size. The following
tables describe the paper sizes that can be used in coax and twinax mode.
Parameters
BIN1 - BIN 6,
MANUAL,
ENVELOPE,
CONTINUOUS
188
Default
LETTER
Printer Emulation
Options
Printer Description
EXEC
7.25 × 10.5 inches
LETTER
8.5 × 11 inches
LEGAL
8.5 × 14 inches
A4
210 × 297 mm
(8.27 ◊ 11.69 inches)
A3
297 × 420 mm
(11.69 ◊ 16.54 inches)
B4
250 × 353 mm
(10.12 ◊ 14.33 inches)
MON
3.8 × 7.5 inches (Monarch
envelopes)
C10
4.1 × 9.4 inches (COM-10
envelopes)
DL
4.3 × 8.6 inches
(DL envelopes)
CUSTOM
User defined size (see AXIS
Network Print Server Technical
Reference for details)
AXIS 5570e / AXIS 5670e User’s Manual
IBM Print Formatting
Paper Orientation
The following table describes the valid paper options:
Parameters
Printer Emulation
Options
Default
BIN1 - BIN 6,
MANUAL,
ENVELOPE,
CONTINUOUS
COR
Printer Description
COR
Computer Output Reduction
(COR) is enabled.
PORT
Use portrait as default print
orientation.
LAND
Use landscape as default print
orientation
Notes:
COR printouts require a Laser Printer with the following characteristics:
ASCII Printer Driver
•
Landscape orientation
•
Vertically compressed to 70%
•
Horizontally compressed by using a font of higher character density
•
Top and left margins of 0.5 inches each by default
This parameter should match the printer type you have connected to your
Axis Network Print Server. Select the correct printer type from the Axis
Network Print Server internal Web pages.
Click Admin | IBM Emulators | Detailed View for SCS/IPDS Emulator
Configuration. Select the desired emulator tab and scroll down to the
Printer Driver parameter. Click OK at the bottom of the page to save your
settings to the print server.
The table below describes the available printer emulation options:
Parameter
PRDRIVER
Default
PCL5
Printer Emulation
Options
Printer Description
GENERIC
Generic Printer Driver
PCL5
PCL5 printer
PCL4
PCL4 printer
IBM_PRO
IBM Proprinter
EPSON_FX
Epson FX
EPSON_LQ
Epson LQ
USER
Editable Printer Driver
Epson 15
Epson FX 15 CPI
Notes:
If you wish to edit the control sequences within a printer driver, the USER driver must be
selected. See AXIS Technical Reference on www.axis.com
AXIS 5570e / AXIS 5670e User’s Manual
189
IPDS Overview
Section 19
IPDS Overview
This section describes:
•
•
IPDS parameter settings
IPDS fonts
IPDS Parameter Settings
Before printing IPDS data streams, the basic parameters should be set.
This is done from the Axis Network Print Server Web pages under IBM
Emulators | Detailed View (IBM IPDS Emulator Settings) where you can
configure the common parameters of the IPDS emulator and IBM
Emulators | Detailed View (SCS/IPDS Emulator Configurations) where
you can configure the settings for each session.
IPDS System Languages
The Axis Network Print Server must be set up for the System Language of
your IBM system configuration in order to obtain the correct characters in
each specific language. This is done from the IBM Emulators | Detailed
View (SCS/IPDS Emulator Configurations) page.
The default selection is US English (Code Page 37).
The following table describes the valid IPDS system languages:
190
Code page
System language
*37
US English, Portuguese Alternate and Canadian Bilingual
256
International set 1
259
Symbols set 7
260
Canadian French
273
Austrian/German
274
Belgian
275
Brazilian
277
Danish/Norwegian
278
Swedish/Finnish
280
Italian
281
Japanese English
282
Portuguese
284
Spanish and Spanish Speaking
285
UK English
286
Austrian/German Alternate
287
Danish/Norwegian Alternate
288
Swedish/Finnish Alternate
AXIS 5570e / AXIS 5670e User’s Manual
IPDS Overview
Code page
System language
289
Spanish Alternate
290
Japanese-Katakana
293
APL
297
French Azerty
361
International Typographic
420
Arabic Bilingual
423
Greek (GKB)
424
Hebrew
437
Multinational
500
Internationa, Set 5 & Swiss Bilingual
803
Hebrew Character Set A
838
Thai
870
Latin 2 Multilingual
871
Icelandic
875
Greek (GNB)
880
Cyrillic Multilingual
892
OCR-A
893
OCR-B
1026
Latin 5
The Euro character is implemented in the Code Pages 1140 - 1149:
Code page
System language - Latin 1 EBCDIC Publishing
1140
US English, Canadian English, Canadian French, Netherlands, Brazil, Portugal
1141
Austrian, German
1142
Danish, Norwegian
1143
Finnish, Swedish
1144
Italian
1145
Castilian Spanish, Latin, American Spanish
1146
UK English
1147
French
1148
Multinational ECECP, Belgian, French, Belgian Dutch, Switzerland
1149
Icelandic
Code page
System language - Latin 1 ASCII
858
Multinational PC with Euro
860
Portuguese (Primary = 850)
861
Icelandic (Primary = 850)
863
Canadian French (Primary = 850)
865
Nordic (Primary = 850)
1004
IBM PC Desktop Publishing
819
ISO Latin 1
1252
Windows Latin 1
Code page
System language - Latin 2/3/4/5 EBCDIC and ASCII
852
Croatian, Czech, East German, Hungarian, Polish, Romanian, Slovak, Slovenian
912
Latin 2 ISO/ ANSI 8 Bit
853
Latin 3 Multilingual PC
AXIS 5570e / AXIS 5670e User’s Manual
191
IPDS Overview
905
IPDS Configuration
Latin 3 Multilingual
1069
Latin 4 EBCDIC
914
Latin 4 ISO/ASCII
857
Latin 5 PC
920
Latin 5 ISO/ANSI 8 Bit
1026
Latin 5
Code page
System language - Latin 9 EBCDIC and ASCII
923
Latin 9
924
Latin 9 EBCDIC
The basic IPDS parameters are set from the IBM Emulators | Detailed
View (IBM IPDS Emulator Settings) page:
Enter the configuration settings for the parameters described below.
When you are finished, click OK at the bottom of the page to save your
settings to the print server.
True Color Support
The Color Support setting determines how color information is to be
interpreted. Enabled means that color commands are sent to the printer.
Disabled means that color information is converted to black-and-white
patterns.
The default setting is Disabled.
Duplex Support
192
The Duplex Support setting determines whether duplex support for the
attached printer shall be reported to the host. Enabled means that duplex
commands are transferred to the printer. Disabled means that duplex
printing is not supported. The default setting is Disabled.
AXIS 5570e / AXIS 5670e User’s Manual
IPDS Overview
Optimize Duplex
Use this option to optimize duplex print jobs. Optimization means that
sheets are printed in simplex if the reverse side of the sheet is empty,
resulting in higher throughput.
Important:
Some printers will internally turn the sheet upside down when duplex is used. This may cause
undesired effects when using pre-printed forms. Setting this parameter to No will force the
entire job to be printed in duplex mode
N-up
The N-up parameter defines if 1, 2 or 4 pages in your document are to be
printed on each physical page.
Default output bin
This selection defines which output paper bin should be used as default.
The default selection is Bin 1.
Default input bin
This selection defines which input paper bin should be used as default.
The default selection is Bin 1.
IPDS bin 1-5
The physical paper size selection must match the actual paper size you are
using for Bin 1-5. The predefined sizes are Statement, Ledger, Folio,
Hagaki, Executive, Letter, Legal, A4 and A3. The default size is A4.
If you are using another paper format, select Custom. This selection
requires that you define the paper size by setting the parameters Physical
Paper Width and Physical Paper Length to the appropriate values.
IPDS PostScript
Configuration
Click the IPDS PostScript Driver Settings tab and enter the configuration
settings for the parameters as described below. When you are finished,
click OK at the bottom of the page to save your settings to the print sever.
Loaded Font
Smoothing
A downloaded 240 dpi font may appear jagged when printed on a 300 dpi
printer. The Axis Network Print Server uses a font smoothing feature to
enhance the appearance of these fonts. The font smoothing may be
disabled if you want to speed up the font loading or if your printer has
insufficient PostScript virtual memory.
Loaded font smoothing is Enabled by default.
Note:
Font smoothing is optimized for printers with 300 dpi resolution. If your printer has a
resolution of 600 dpi or higher, the smoothing effect will be less significant. In these cases we
recommend that you disable the font smoothing to avoid reduction in the performance.
PostScript Error
Handler
Use this parameter to download a PostScript Error Handler to the printer
at power on. Once downloaded, the Error Handler will print an error
message if a PostScript error occurs. The Error Handler is Disabled by
default.
AXIS 5570e / AXIS 5670e User’s Manual
193
IPDS Overview
Optimize Overlays
Enabling this parameter will activate an overlay optimization feature
resulting in faster throughput when using host downloaded overlays.
Enabling this feature will require more free Postscript Virtual Memory in
the printer.
Virtual
Memory kB
This value defines how much memory the Axis Network Print Server can
use in the PostScript printer for storing resources.
The default value is 2000 kbytes.
PostScript
bin 1-5
PostScript
output bin settings
IPDS PCL
Configuration
Language version
Map each PostScript bin (1-5) to a bin number or choose Default. Enter
the desired values in the Horizontal scale factor, Vertical scale factor,
Horizontal offset and Vertical offset fields.
These parameters are for mapping the IPDS bin numbers to the bin
numbers of the connected postscript printer.
Click the IPDS PCL Driver Settings tab and enter the configuration
settings for the parameters as described below. When you are finished,
click OK at the bottom of the page to save your settings to the print sever.
Select the correct PCL language version depending on your connected
printer.
Symbol set
Select the preferred symbol set from the drop-down list. The default and
recommended value is AUTOMATIC. The print server will automatically
select the appropriate symbol set.
PCL bin 1-5
Define the positioning by setting the parameters Horizontal Offset and
Vertical Offset to the desired values.
PCL Output Bin
These parameters are for mapping the IPDS bin numbers to the bin
numbers of the connected PCL printer.
IPDS Fonts
This section describes how IPDS fonts are handled by the Axis Network
Print Server. There are two different approaches to font handling:
• downloading fonts from the host.
• using fonts that are already resident in the printer.
Both methods are supported by the Axis Network Print Server.
Host Downloaded
fonts
194
IPDS provides functions for downloading fonts from the host computer.
The font resolutions of 240, 300 and 600 dpi are automatically converted
by Axis Network Print Server to the resolution of the attached printer.
AXIS 5570e / AXIS 5670e User’s Manual
IPDS Overview
AS/400 downloaded fonts requires [AFP = *YES] in the AS/400 device description.
Printer Resident Fonts
The rest of this section deals with printer resident fonts. The non-standard
PostScript fonts are resident in the Axis Network Print Server (OCR-B is
one example), so you do not need font cards etc. to use the listed fonts.
In IPDS mode, printer resident fonts can be selected by the system
referring to the FGID (Font Global IDentifier) and FW (Font Width). Axis
Network Print Server supports a large set of resident fonts.
Note:
(IBM Mainframe only) For PSF systems, resident fonts need to be mapped to the host font
name and code page. In PSF/MVS, this is done using the APSRMARK utility and in PSF/VM
using the APRFTBLV (RSCS) or APRFTIDB files. For more information, refer to the PSF/MVS and
PSF/VM manuals.
The FGIDs are grouped according to the following table:
FGID (hex)
FGID (dec)
TYPE
0001 - 0041
1 -65
10 CPI
0042 - 0099
66 - 153
12 CPI
009A - 00C8
154 - 200
Proportional PSM
00C9 - 00D2
201 - 210
13 CPI
00D3 - 00EF
208 - 239
15 CPI
00F0 - 00F7
240 - 247
5 CPI
00F8 - 0103
248 - 259
17 CPI
0104 - 0111
260 - 273
8 CPI
0112 - 0117
274 - 279
17 CPI
0118 - 011B
280 - 283
20 CPI
011C - 0120
284 - 288
25 CPI
0121 - 012B
289 - 299
27 CPI
012C - 01FF
300 - 511
10 CPI
FGID (hex)
FGID (dec)
TYPE
0200 - 0EFF
512 - 3839
Typographic
0F00 - 0FFF
3840 - 4095
User Defined Fonts
1000 - FFFE
4096 - 65534
Typographic
The Axis Network Print Server supports extended font mapping at
PostScript level, making it possible to redefine any of the FGIDs.
AXIS 5570e / AXIS 5670e User’s Manual
195
IPDS Overview
Immediate Font Substitutions
Certain FGIDs will be immediately substituted by the Axis Network Print
Server. The substitution table depends on the selected IBM printer
emulation.
Unsupported Fonts
A selection of an unsupported FGID value will result in a substitution to a
default font. The Axis Network Print Server uses the same default fonts as
the emulated IBM printers.
Typographical Fonts
This section deals with font width selections for typographical
(proportional pitch) fonts.
Note that when an unsupported typographical font (FGID range 512 65534) is selected, the resulting font will be a fixed pitch and the selected
font width value will be ignored.
Default Font Width
When the default font width is selected, the Axis Network Print Server
will set a font width in one of the following ways depending on the
selected IBM printer emulation:
IBM 4028/4332
The font width is set to 67 (corresponding to a 10 point font).
IBM 3812/3816
The font width is set to the smallest available value for the selected FGID.
For FGID 16951 (Century Schoolbook), the resulting font width is 102 (12
points), and for FGID 5687 (Times Roman), the resulting font width is 40
(6 points).
Scalable Fonts
If the selected font width (point size) is not available for the selected
FGID, the Axis Network Print Server will set a point size in one of the
following ways depending on the font:
Times Roman,
Helvetica
and Century
Schoolbook
The font width value is converted to a point size used to dynamically
scale the selected font. This means that you have a completely free choice
of point sizes (only limited by the host application) when printing with
these fonts.
Any other
typographical font
The nearest smaller available font width for the selected FGID will be
used. If a smaller font width is not available, the nearest larger font width
will be used.
196
AXIS 5570e / AXIS 5670e User’s Manual
DBCS Support
Section 20
DBCS Support
The Axis Network Print Server supports Double-Byte Character Set
(DBCS) for SNA and TN5250E printing. This facilitates printing from an
IBM AS/400 host system for languages employing double-byte character
sets.
The following Chinese, Japanese and Korean DBCS tables are used in the
Axis Network Print Server:
Country
Printer Emulation
Korea (KS)
5x27_002_TX_KS
Character Table
KS
Korea (KSSM)
5x27_002_TX_KSSM
KSSM
Japan
5x27_001_TX
Shift - JIS
China
5x27_005_TX
GB
Axis Network Print Server Double-byte Character Tables
Important!
The Axis Network Print Server supports SNA DBCS printing in IBM 5494
emulation only.
Configuring the AS/400 Host, 5494 CU mode
Follow the instructions below to configure the AS/400 Host for DBCS
support:
1. Type WRKSYSVAL on the AS/400 command line and press Enter.
2. Check that the DBCS version installed indicator (QIGC) sysval is set to 1 (on).
3. Check that the QIGCCDEFNT sysval is set to a DBCS font installed in the
system.
4. Proceed with the steps detailed in The AS/400 Host System Checklist, on
page 23.
Configuring the Axis Network Print Server
A number of printer emulations exist for DBCS printing. To set the correct
system language and printer driver, refer to the tables below and enter the
values in the IBM Configuration Wizard.
Country
Printer Emulation
System Language
Korea (KS)
5x27_002_TX_KS
833
Korea (KSSM)
5x27_002_TX_KSSM
833
Japan
5x27_001_TX
290
China
5x27_005_TX
836
Printer Emulation and System Language for Country options
AXIS 5570e / AXIS 5670e User’s Manual
197
DBCS Support
Country
PCL Printer Driver
Korea (KS)
Korea (KSSM)
Japan
Matrix Printer Driver
Epson LQ KS
None
PCL5
None
China
Epson LQ 1600K
Taiwan
Epson LQ 1600K
1. Start a Web browser, e.g. Internet Explorer or Netscape Navigator.
2. Enter the IP address or the host name of the Axis Network Print Server in
the location field and press the Enter key on your keyboard. The internal Web
pages of the Axis Network Print Server will appear.
Important:
To protect the admin pages and the Configuration Wizard from unauthorized use, enter a
password (default Pass) in the Root Password field under Admin | General Settings.
3. Click the Configuration Wizard for IBM sessions button.
4. Click the Add Session button. This will start the Configuration Wizard
which is a step-by-step guide through the required IBM configuration
settings.
Note:
Default fonts will be changed when switching printer emulations.
Verifying the Communications Link
Having configured the AS/400 host Axis Network Print Server in
accordance with the above, verify that the communications link is
functioning correctly by following instructions 1-4 detailed in Verifying
the Communication Link, on page 29.
Amending Device Features
After automatic setup, it may be necessary to change the Device features
and Last Code Point of the printer device. Failure to do so may cause
corruption within your print data.
Follow the instructions below, to set the appropriate Device features and
Last Code Point for your chosen printer device:
198
AXIS 5570e / AXIS 5670e User’s Manual
DBCS Support
1. Make sure that the writer is stopped by typing ENDWTR xxxxPRT01
on the AS/400 command line, where xxxxPRT01 is the printer device
name. Press ENTER.
2. Type VRYCFG CFGOBJ(xxxxPRT01) CFGTYPE(*DEV)
STATUS(*OFF) to vary off the printer device, where xxxxPRT01 is the
printer device name. Press ENTER.
3. Type CHGDEVPRT xxxxPRT01 to change the printer device name, where
xxxxPRT01 is the printer device name. Press F4.
4. Under DBCS Feature (IGCFEAT) amend the Device Features and Last Code
Point to the appropriate value corresponding to the country language.
Country
Device features
Korea
2424K1
Last Code Point
D3FE
Japan
2424J1
68FE
China
2424S1
6FFE
Device features and Last Code Point for Country options
5. Type VRYCFG CFGOBJ(xxxxPRT01) CFGTYPE(*DEV)
STATUS(*ON) on the AS/400 command line to vary on the printer device,
where xxxxPRT01 is the printer device name. Press ENTER.
6. Type STRPRTWTR xxxxPRT01 to start the Writer, where xxxxPRT01
is the printer device name. Press ENTER.
7. Direct a printout to this printer device to confirm that the above changes
have been implemented correctly.
Extended IBM Printer Emulation
Extended emulation will only work in SBCS mode. Before entering
extended emulation you will have to change to single byte mode by
sending shift in.
<SI>(SCS Shift In Control Code)
%CONFIG+
SAVE;
%CONFIG-
<SO>(SCS Shift Out Control Code)
Example (with DBCS mode before entering extended emulation)
AXIS 5570e / AXIS 5670e User’s Manual
199
DBCS Support
Font Tables
The following tables define the DBCS font types supported in the Axis
Network Print Server (5494 CU Mode):
DBCS FONTS (Japan)
200
DBCS FONTS (China)
FGID
IBM Font Name
FGID
IBM Font Name
50000
MS Mincho
10 CPI
50100
SimSun
10 CPI
50001
MS Mincho
10 CPI
50101
SimSun
10 CPI
50014
MS Mincho
10 CPI
50114
SimSun
10 CPI
50002
MS Mincho
12 CPI
50102
SimSun
12 CPI
50015
MS Mincho
12 CPI
50115
SimSun
12 CPI
50003
MS Mincho
13.3 CPI
50103
SimSun
13.3 CPI
50016
MS Mincho
13.3 CPI
50116
SimSun
13.3 CPI
50007
MS Mincho
14.3 CPI
50107
SimSun
14.3 CPI
50008
MS Mincho
14.3 CPI
50108
SimSun
14.3 CPI
50019
MS Mincho
14.3 CPI
50119
SimSun
14.3 CPI
50004
MS Mincho
15 CPI
50104
SimSun
15 CPI
50005
MS Mincho
15 CPI
50105
SimSun
15 CPI
50017
MS Mincho
15 CPI
50117
SimSun
15 CPI
50009
MS Mincho
17.1 CPI
50109
SimSun
17.1 CPI
50020
MS Mincho
17.1 CPI
50120
SimSun
17.1 CPI
50006
MS Mincho
18 CPI
50106
SimSun
18 CPI
50018
MS Mincho
18 CPI
50118
SimSun
18 CPI
50010
MS Mincho
18.9 CPI
50110
SimSun
18.9 CPI
50021
MS Mincho
18.9 CPI
50121
SimSun
18.9 CPI
500111
MS Mincho
21.5 CPI
50111
SimSun
21.5 CPI
50012
MS Mincho
21.5 CPI
50112
SimSun
21.5 CPI
50022
MS Mincho
21.5 CPI
50122
SimSun
21.5 CPI
50013
MS Mincho
25.7 CPI
50113
SimSun
25.7 CPI
50023
MS Mincho
25.7 CPI
50123
SimSun
25.7 CPI
AXIS 5570e / AXIS 5670e User’s Manual
DBCS Support
DBCS FONTS (Korea KS)
DBCS FONTS (Korea KSSM)
FGID
IBM Font Name
FGID
IBM Font Name
50030
HanYang
10 CPI
50130
Compst
10 CPI
50031
HanYang
10 CPI
50131
Compst
10 CPI
50044
HanYang
10 CPI
50144
Compst
10 CPI
50032
HanYang
12 CPI
50132
Compst
12 CPI
50045
HanYang
12 CPI
50145
Compst
12 CPI
50033
HanYang
13.3 CPI
50133
Compst
13.3 CPI
50046
HanYang
13.3 CPI
50146
Compst
13.3 CPI
50037
HanYang
14.3 CPI
50137
Compst
14.3 CPI
50038
HanYang
14.3 CPI
50138
Compst
14.3 CPI
50049
HanYang
14.3 CPI
50149
Compst
14.3 CPI
50034
HanYang
15 CPI
50134
Compst
15 CPI
50035
HanYang
15 CPI
50135
Compst
15 CPI
50047
HanYang
15 CPI
50147
Compst
15 CPI
50039
HanYang
17.1 CPI
50139
Compst
17.1 CPI
50050
HanYang
17.1 CPI
50150
Compst
17.1 CPI
50036
HanYang
18 CPI
50136
Compst
18 CPI
50048
HanYang
18 CPI
50148
Compst
18 CPI
50040
HanYang
18.9 CPI
50140
Compst
18.9 CPI
50051
HanYang
18.9 CPI
50151
Compst
18.9 CPI
50041
HanYang
21.5 CPI
50141
Compst
21.5 CPI
50042
HanYang
21.5 CPI
50142
Compst
21.5 CPI
50052
HanYang
21.5 CPI
50152
Compst
21.5 CPI
50043
HanYang
25.7 CPI
50143
Compst
25.7 CPI
50053
HanYang
25.7 CPI
50153
Compst
25.7 CPI
AXIS 5570e / AXIS 5670e User’s Manual
201
Digital Copier Support
Section 21
Digital Copier Support
The logical printers support the printing options available on digital
copiers and multi-functional printers. It is recommended that you
configure the eight logical printers (PR1-PR8) to allow for eight different
combinations of the following options to suit your printing needs.
For more information on how to configure the logical printers, please
refer to “Logical Printers for Customized Printing” on page 154.
The added functionality includes the following options:
Copier Model
From the drop-down list of supported copiers, select the digital copier
that you have connected the Axis Network Print Server to.
Copier Duplex
The Axis Network Print Server supports duplex printing i.e. printing on
both sides of the paper. The options in the drop-down list are:
•
•
•
•
Copier Staple
The Axis Network Print Server supports stapling with the following
options:
•
•
•
•
•
•
•
Copier Hole Punch
Off i.e. the stapling option is not activated (default).
Top left slant i.e. one staple in a slanted position in the top left corner
of the document.
Top left horizontal i.e. one staple placed horizontally in the top left
corner of the document.
Top left vertical i.e. one staple placed vertically in the top left corner of
the document.
Top 2 i.e. two staples at the top of the document.
Left 2 i.e. two staples on the left hand side of the document.
Center 2 i.e. two staples set in the center of the page. This option is
intended for documents printed in A3 format. The staples are placed in
the center of the page where the document is to be folded. Please refer
to the documentation of your digital copier for more information on
these features.
The Axis Network Print Server supports hole punching with the following
options:
•
•
•
202
Off i.e. the duplex printing option is not activated (default).
Simplex i.e. printing on one side only.
Long-edge binding i.e. printing on both sides, long-edge first.
Short-edge binding i.e. printing on both sides, short-edge first.
Off i.e. the hole punching option is not activated (default).
Long-edge i.e. the left hand side of the document.
Short-edge i.e. the top of the document.
AXIS 5570e / AXIS 5670e User’s Manual
Digital Copier Support
Copier Paper Source
Copier Copies
Enter the desired input bin i.e. paper tray on your digital copier
Enter how many collated (sorted) copies you wish to print in the Copies
field.
Note:
•
The options are all available in the drop-down lists under Model, Duplex, Staple, Punch,
Paper Source and Copies. However, you must refer to the documentation of your specific
Digital Copier to check that all the options are supported.
If you experience problems with this functionality the Digital Copier printing options may
have been set inconsistently. Please check your configuration settings and try again.
AXIS 5570e / AXIS 5670e User’s Manual
203
IP Addressing
Section 22
IP Address and Subnet
Mask
IP Addressing
The print server must be correctly configured with the following
information to function properly:
•
•
•
an IP address
a subnet mask
a default gateway (or router)
IP Address
Each device on your network must have a unique IP address to operate
correctly. An IP address identifies the address of the device to which data
is being sent and the address of the destination network. IP addresses
have the format n.n.n.x where n is a decimal number between 0 and 255
and x is a number between 1 and 254 inclusive.
Subnet Mask
In addition to the IP address, you need to set a subnet mask. All networks
are divided into smaller sub-networks and a subnet mask is a number that
enables a device to identify the sub-network to which it is connected.
For your network to work correctly, all devices on the subnet must have:
• The same sub-network address
• The same subnet mask
The only value that will be different is the specific host device number.
This value must always be unique. The size of the network determines the
structure of the IP addresses in it.
Default Gateway
IP Address and Subnet
Mask Structures
In a network using subnets, the router that forwards traffic to a
destination outside of the subnet of the transmitting device. If there is a
server or a router which functions as a gateway, enter the IP address of
the server or the router.
Two of the most common types of IP address and subnet mask structures
are described here:
Type One
In a small (Class C) network, the IP address example ‘192.168.3.191’ is
split into two parts:
•
Part one (‘192.168.3’) identifies the network on which the device
resides.
• Part two (‘.191’) identifies the device within the network.
This type of IP address generally operates on a subnet mask of
‘255.255.255.0’.
204
AXIS 5570e / AXIS 5670e User’s Manual
IP Addressing
Type Two
In larger (Class B) networks, where there are more devices, the IP address
of ‘162.168.3.191’ is split into two parts but is structured differently:
• Part one (‘162.168’) identifies the network on which the device resides.
• Part two (‘.3.191’) identifies the device within the network.
This type of IP address operates on a subnet mask of ‘255.255.0.0’.
Default Gateway
Examples
1. This example shows a network with:
•
•
•
one computer
one networked printer
no router
Device
print server
pc1
IP address
192.168.3.191
192.168.3.192
Subnet Mask
255.255.255.0
255.255.255.0
Default Gateway
*
*
* When no router is present on the network, the default gateway can be
left undefined.
2. This example shows a network with:
•
•
•
Obtaining an IP
Address and Subnet
Mask
one computer
one networked printer
a router with IP value: 192.168.3.1
Device
IP address
Subnet Mask
Default Gateway
print server
pc1
192.168.3.191
192.168.3.192
255.255.255.0
255.255.255.0
192.168.3.1
192.168.3.1
There are three different ways to obtain an IP address and subnet mask.
These are:
•
•
•
Dynamic Host Configuration Protocol (DHCP) Addressing
Static Addressing
Automatic Addressing (Auto-IP Addressing)
DHCP Addressing
If your network contains a DHCP server, print servers on your network
will obtain an IP address and subnet mask automatically. DHCP assigns a
temporary IP address and subnet mask which gets reallocated once you
disconnect from the network. DHCP will work on any client Operating
System such as Windows 95, 98 or NT. Also, using DHCP means that the
same IP address and subnet mask will never be duplicated for devices on
the network. DHCP is particularly useful for networks with large numbers
of users on them.
Static Addressing
With this method you must enter an IP Address and the subnet mask
manually on every device. Using a static IP and subnet mask means the
address is permanently fixed.
AXIS 5570e / AXIS 5670e User’s Manual
205
IP Addressing
Auto-IP Addressing
Network devices use automatic IP addressing if they are configured to
acquire an address using DHCP but are unable to contact a DHCP server.
Automatic IP addressing is a scheme where devices allocate themselves an
IP address at random from the industry standard subnet of 169.254.x.x
(with a subnet mask of 255.255.0.0). If two devices allocate themselves
the same address, the conflict is detected and one of the devices allocates
itself a new address.
Automatic IP addressing support was introduced by Microsoft in the
Windows 98 operating system and is also supported in Windows
2000/XP/2003.
Registering and
Resolving
Host Names
In order to register the host name of the print server in networks with
dynamic IP address settings, WINS (Windows Internet Name Service) and
DDNS (Dynamic Domain Name System) are supported. It is recommended
that at least one of these methods should be used if you are setting the IP
address of the print server using DHCP.
The host name of the print server is specified by the PS_NAME.
parameter. Refer to the “The Parameter List” on page 216.
WINS Host Name
Rules
WINS only supports 15 character long host names. If your host name is
longer than 15 characters, the print server truncates the host name to 15
characters when registering with a WINS server. You can view the print
server’s host name that is registered at a WINS server in the print server’s
Web interface. Refer to “Using a Web Browser for Print Server
Management” on page 128.
DDNS Host Name
Rules
DDNS supports 47 character long host names and can only consist of the
characters ‘A-Z’, ’a-z’, ’0-9’ and ‘-’. If your host name consists of any
other characters, they are converted to ‘-’ when registering with a DDNS
server. You can view which host name that is registered at a DDNS server
in the print server’s Web interface. Refer to “Using a Web Browser for
Print Server Management” on page 128.
If the host name matches another entry in the DDNS data base, the print
server deletes that entry before registering.
Notes:
• The default host name of the print server is ’AXIS’ followed by the last 6 digits in the serial
number. e.g. AXIS181636. The host name (Print server name) can be changed in the
PS_NAME. field on the Admin | General Settings page.
• The host name limitations conclude that if you want to register the same host name at a
WINS server and a DDNS server, the host name should be no longer than 15 characters and
it should only contain the characters ‘A-Z’, ‘a-z’, ’0-9’ and ‘-’.
• Refer to your system manuals or to your network administrator for instructions on how
host name resolutions are performed on your system.
206
AXIS 5570e / AXIS 5670e User’s Manual
IP Addressing
Setting the IP Address
using DHCP
Follow the instructions below to download the IP address using DHCP:
1. Edit or create a scope in the DHCP manager of the DHCP daemon. The
entries included in this scope should contain the following parameters:
• range of IP addresses
• subnet mask
• default router IP address
• WINS server IP address(es) or DDNS server IP address(es)
• lease duration
2. Activate the scope. The print server automatically downloads the DHCP
parameters. If you are using WINS or DNS, you should include at least one
WINS or DNS server IP address in the DHCP scope. Immediately after the IP
address has been received, the print server registers its host name and IP
address on the WINS alternatively DNS server. Refer to “Registering and
Resolving Host Names” on page 206 for more information. The print server
can automatically download a customized config file from a TFTP server. Just
add the name of the config file and the TFTP server’s IP address to your DHCP
scope. The config file is downloaded immediately after the print server
receives its IP address.
3. You have now successfully set the IP address of your print server.
Note:
You have to restart the print server to download the IP address.
AXIS 5570e / AXIS 5670e User’s Manual
207
The Test Button
Section 23
The Test Button
The test button is located on the front right hand side of the AXIS
5570e/AXIS 5670e and is used for:
• Printing a test page to check the connection to the printer.
• Printing a parameter list to see the print server’s current settings.
• Performing a Factory Default of the print server.
If you want to change any of the parameters, use one of the methods
described in “Management and Configuration” on page 128.
Printing a Test Page
Press the test button once to print a test page. The Test Page contains
basic information about the AXIS 5570e/AXIS 5670e. It is recommended
that you print a test page every time you have connected the print server
to a printer.
Printing a Parameter
List
Press the test button twice to print a parameter list showing the current
AXIS 5570e/AXIS 5670e settings. This list provides comprehensive details
of all the parameters and their current status. Refer to The Parameter List,
on page 216.
If you want to change any of the parameters, use one of the methods that
are described in Management and Configuration, on page 128.
Performing a Factory
Default
1. Remove the external power supply to switch off the print server.
2. Press and hold down the test button while you reconnect the external power
supply.
3. Continue to hold down the test button until the network indicator remains
constantly lit. This should take about 20 seconds.
4. Restart the print server by disconnecting and reconnecting the external
power supply.
Important!
A Factory Default will reset all AXIS 5570e/AXIS 5670e parameters and settings to their
default values except:
208
•
Installed certificate
•
Private key
AXIS 5570e / AXIS 5670e User’s Manual
Troubleshooting
Section 24
Troubleshooting
This section provides useful information to help you resolve difficulties
you might have with your AXIS 5570e/AXIS 5670e. Fault symptoms,
possible causes and remedial actions are provided within a quick
reference table.
Please visit the Axis Web site for latest troubleshooting tips, more support
and additional help through the FAQ database or to fill in and submit a
Support question.
Overriding Port Status
Some USB printers do not deliver correct port status to the print server
(for instance always reporting printer off-line even if the printer is online). To override this, see “Overriding Port Status” on page 168.
LED Indicators
Indicator
Power
Network
Color/Behavior
Explanation
Green
OK
Not lit
No power/Error
Orange
OK - network connected
Orange flashing
Activity on network
Not lit
No physical connection to the network
Web Interface
Symptoms
Possible causes
Remedial actions
The AXIS 5570e/AXIS 5670e is not
connected properly.
1. Check Power and Network indicator.
2. Check that assignment of IP addresses
for the AXIS 5570e/AXIS 5670e is correct.
3. To further check the IP addresses, run
the Ping command from another computer as described in "IP address check"
at the end of this chapter. Follow the
appropriate recommendations.
Problem with your proxy server.
Verify the proxy server settings in your
Web browser.
Other networking problems.
1. Verify that your network is accessible
through your network socket.
2. Verify that your network cable is functional.
The AXIS 5570e/AXIS 5670e Web
interface cannot be accessed
from a Web browser.
AXIS 5570e / AXIS 5670e User’s Manual
209
Troubleshooting
IP Address Check with
Ping
Windows:
By sending a data packet to a specific IP address and waiting for a reply,
Ping can determine whether that IP address is accessible. Ping can also
help you to determine IP address conflicts with your AXIS 5570e/AXIS
5670e and troubleshoot TCP/IP problems on the network. Follow the
instructions below to diagnose your problem.
Open a Command Prompt and enter the following commands:
Example
ping 192.168.3.191
Syntax
ping <IP address>
The host will return reply from 192.168.3.191, or a similar message. This
indicates that the address has been set and that communication is
established
UNIX/Linux and
Mac OS X
Open a Terminal and enter the following commands:
Example
ping 192.168.3.191
Syntax
ping <IP address>
The host will return psname is alive, or a similar message. This indicates that
the address has been set and that communication is established.
Replies:
Subsequent replies will provide an explanation of the cause of the problem.
Replies from DOS can be interpreted as defined in the table below (for
UNIX/Linux replies please refer to the UNIX/Linux chapter of this manual):
Interpretation and recommendation
Ping Reply
SNMP Device Index
210
Axis Network Print Server
connected
Axis Network Print Server
disconnected
bytes = 32 time = 2 ms......
- or something similar
The AXIS 5570e/AXIS 5670e is responding correctly. There are probably
no conflicts with the IP address - disconnect the AXIS 5570e/AXIS 5670e
and ping again to verify.
The IP address is already in use and
cannot be used again. You must obtain
a new IP address for your AXIS
5570e/AXIS 5670e.
destination host
unreachable
The AXIS 5570e/AXIS 5670e is not accessible. Check your network settings.
—
request timed out
The IP address is not in use. You are
either pinging the wrong IP address or
your AXIS 5570e/AXIS 5670e does not
have the correct IP address.
This IP address is not used by anyone
and is available for use for your AXIS
5570e/AXIS 5670e. Set the IP address
again, power on the AXIS 5570e/AXIS
5670e and then try accessing the unit.
no response from
ping command
The AXIS 5570e/AXIS 5670e is not accessible. Check your network settings.
—
If you are using the TCP/IP protocol, check that the SNMP Device Index is
correct. See “SNMP Device Index” on page 276.
AXIS 5570e / AXIS 5670e User’s Manual
Troubleshooting
Axis Support
Server Report
In order to obtain optimal support from Axis support technicians, please
follow these instructions when filling in and submitting a Support
question.
1. Go to the print server’s Web pages by typing the print server’s IP address
in the Address/Location field of your Web browser.
2. Go to Admin | Support. Click the Server Report link. A new window will
open.
3. Save the Server report as an HTML file (with an .html file extension) and go
to the Axis Web site.
4. Choose Support and report your case, attaching the Server Report.
AXIS 5570e / AXIS 5670e User’s Manual
211
Technical Specification
Section 25
Supported Printers
Technical Specification
All printers and copiers except except host-based printers such as
Windows GDI.
IBM Capabilities
IBM Mainframe
(zSeries)
• OS: IBM S/370, S/390, 30xx, 43xx, 47xx, 937x, 81xx
• TCP/IP based protocols: TN3270E, PPR/PPD, LPR/LPD and RawTCP
• SNA support: LU1 and LU3 (node type 2.0) for IBM 3174 Control unit
emulation
• Data streams: IPDS, SCS, 3270DS as well as PostScript, PCL and ASCII
• Emulated printers: 4332, 4028, 3812 model 2, 3816 model 01S and 01D,
4224, 4230, 3287, 3268, 4214 and 3262
IBM AS/400
(iSeries)
• OS: IBM OS/400
• TCP/IP based protocols: TN5250E, PPR/PPD, LPR/LPD and RawTCP.
• SNA support: LU6.2 (node type 2.1) for IBM 5494 Control unit
emulation
• Data streams: IPDS, SCS as well as PostScript, PCL and ASCII
• Emulated printers: 4332, 4028, 3812, 3816, 4214-2, 5224, 5225, 5256,
4230, 5x27-2 KS, 5x27-3 KSSM, 5x27-3 and 5x27-5
Supported Systems
Microsoft Windows
Novell NetWare
Apple
Unix/Linux
Additional Systems
212
95, 98, Me, NT, 2000, XP and 2003 Server
3.X, 4.X, 5.X, 6.X. Supports bindery and NDS mode. Supports user
messages and printer status. NDPS supported over IP and IPX. Support for
iPrint using both LPR and IPP protocols. PSERVER (IP/IPX),
RPRINTER/NPRINTER supported
Mac OS 7, 8, 9, Mac OS X version 10.X
All Unix systems supporting TCP/IP (Linux, BSD, System V, Solaris, HPUX, IBM AIX, Silicon Graphics IRIX, etc.)
Other systems supporting TCP/IP:
IBM (MVS, VM, VSE, OS/400), DEC, VMS
Microsoft LAN Manager
IBM LAN Server
LANtastic
AXIS 5570e / AXIS 5670e User’s Manual
Technical Specification
Supported Web
browsers
Supported Protocols
Any standard Web browser (Netscape 6.x and higher and MS Internet
Explorer 5.x and higher)
NetBIOS/NetBEUI
TCP/IP
ARP, DHCP, BOOTP, RARP, DNS, DDNS, Telnet, TFTP, FTP, LPR, Reverse
Telnet, PROS, IPP, IP, TCP, UDP, HTTP, HTTPS, SSL/TLS, SNMP, SNMP
v2c, v3, SLP v1/v2, ICMP, IGMP, Bonjour
NetWare
IPX, SPX, SAP, NCP (extended with NDS), NDPS, NLSP, LIP, RIP, RIP-II,
OSPF
Apple EtherTalk
AAPR, ATP, DDP, NBP, PAP, RTMP, ZIP
Logical Printers
Logical printer ports can be programmed to perform auto ASCII to
PostScript conversion, add string before and after job, string substitution,
alternative output and character set conversion
Copiers
Security
Each logical printer port can be configured to activate a number of
finishing options in the digital copier. Please visit the support pages at
www.axis.com for a list of supported copiers
Password protected configuration
SSL/TLS support for HTTPS secure management
NetWare: Encrypted passwords, NetWare Packet Signature Level 1, 2, 3
Option to disable protocols
Print Server
Management
AXIS ThinWizard for installation, configuration, monitoring and
firmware upgrading of multiple units
Bonjour support for quick and easy installation in Mac OS X evironments
AXIS AddPrinter for easy and automated installation in Windows
environments
Internal Web pages or FTP for installation, configuration, monitoring and
firmware upgrading
SNMP-MIB II compliant (RFC 1213), Axis private enterprise MIB included
Netware: Full PCONSOLE, NWAdmin, ConsoleOne and iPrint-iManager
support
Firmware Upgrade
Firmware upgrade using AXIS ThinWizard, the print server’s Web pages
or FTP
AXIS 5570e / AXIS 5670e User’s Manual
213
Technical Specification
Network Connection
All standard Ethernet and Fast Ethernet networks: RJ-45 connector
(Category 5 or 6, shielded twisted pair cable) for 10baseT or 100baseTX
Ethernet with full duplex
Supports: IEEE802.2, IEEE802.3, SNAP and Ethernet II frame types
simultaneously
NWay for autodetection of network speed
Printer Connection
AXIS 5570e
Bi-directional support for Apple EtherTalk, Reverse Telnet and PROS
Parallel: 36-pin Centronics connector, high-speed IEEE 1284 compliant
with ECP support and throughput of 1 MB/sec
USB: USB 1.1 Low and Full speed. Successfully tested with USB 2.0
Printers
Note: If the AXIS 5570e is powered from the printer via the parallel port
(i.e. instead of via the Power Adapter), the USB port will be switched off.
To make both ports work, use the Power Adapter supplied with the print
server.
AXIS 5670e
Parallel: Two 25-pin DSUB parallel ports, high-speed IEEE 1284
compliant with ECP support and throughput of 1 MB/sec
Serial: One 9-pin DSUB connector, RS-232, XON/ XOFF or RTS/CTS, data
rates up to 115,200 baud
Hardware
Processor
Memory
Front Panel
AXIS Etrax 100LX 32-bit 100 MHz RISC
2 MB Flash, 8 MB RAM
2 LED indicators: Power and Network
Test button for information printouts
Power Consumption
214
Power provided by external supply. Maximum 5.6W (Type PS-H, 5.1 VDC
2000mA)
AXIS 5570e / AXIS 5670e User’s Manual
Technical Specification
Dimensions
AXIS 5570e
Height: 2.9 cm/1.1 in,
Width: 6.2 cm/2.4 in,
Depth: 11.7 cm/4.6 in,
Weight: 0.081 kg/ 0.18lb
AXIS 5670e
Height: 2.9 cm/1.1 in,
Width: 16.0 cm/6.3 in,
Depth: 12.9 cm/5.1 in,
Weight: 0.28 kg/0.64 lb
Environmental
Temperature: 40-105 °F (5-40 °C)
Humidity: 10-90% non-condensing
Approvals
EMC
Safety
Included Accessories
-EN 55022/1998
-EN 55024:1998
-EN 61000-3-2
-EN 61000-3-3
-VCCI Class B
-C-TICK AS/NZS 3548
-Compliance to FCC part 15 Subpart B, Class B
EN 60950
AXIS Network Product CD with software for installation, management
and printing, including AXIS ThinWizard (the recommended Axis
management software)
User documentation
Quick Installation Guide
Power adapter
All specifications are subject to change without prior notice.
AXIS 5570e / AXIS 5670e User’s Manual
215
The Parameter List
Section 26
The Parameter List
These are the default parameters in a new, unconfigured print server. A
complete list of all Axis print server parameters can be found on
www.axis.com
AXIS 5570e
(AXIS 5570e Network Print Server V7.06 Nov
00408C181EC4)
4 2005. S/N:
Parameter settings:
--- General Menu
NODE_ADDR.
: 00 40 8C 18 1E C4
NETWORK_SPEED. : AUTO_SENSE (AUTO_SENSE, 10_HALF_DX,
10_FULL_DX, 100_HALF_DX, 100_FULL_DX)
PS_NAME.
: AXIS181EC4
ROOT_PWD.
: pass
SWUP_KEY.
:
USERS.
:
BASE_URL.
: www.axis.com
CHARSET.
: ISO-8859-1 (ISO-8859-1, UTF-8)
AXIS_PRINT_SYSTEM. : YES
RCONFIG_ENB. : YES
HPPI.
: NO (YES, NO)
DEF_OUT.
: PR1 (PR1, PR2, PR3, PR4, PR5, PR6, PR7, PR8,
LPT1, USB1)
SYS_LOC.
:
SYS_CONT.
:
--- SNA Menu
SNA_ENB.
DEVICE_EMUL.
SNA_FR_TYPE.
NODE_ID.
NODE_SAP.
NWORK_NAME.
LU_NAME.
H1_SAP.
H1_ADDR.
H1_NW_NAME.
H1_MOD_NAME.
H1_LU_NAME.
SNA_LU1.
SNA_LU2.
SNA_LU3.
SNA_LU4.
SNA_LU5.
SNA_LU6.
SNA_LU7.
SNA_LU8.
AUTODIAL.
DIALTIME.
JOB_TIME.
IR_TIME.
SNA_HEXDUMP.
PR8)
:
:
:
:
:
:
:
:
:
:
:
:
:
:
:
:
:
:
:
:
:
:
:
:
:
YES
3174 (3174, 5494)
FR_802_2 (FR_AUTO, FR_802_2, FR_DIX)
E0 78 1E C4
$4
APPN
A4CE181C
$4
FF FF FF FF FF FF
APPN
QRMTWSC
DEFAULT
NONE, 1
NONE, 2
NONE, 3
NONE, 4
NONE, 5
NONE, 6
NONE, 7
NONE, 8
NO
20
10
0
NONE (NONE, PR1, PR2, PR3, PR4, PR5, PR6, PR7,
--- LLC Menu
216
AXIS 5570e / AXIS 5670e User’s Manual
The Parameter List
LLC_RESPONSE. : 1300
LLC_REC_ACK. : 20
LLC_INACTIVITY. : 15
--- TN3270E
TN3270E_IR. : 0
TN3270E_COMP. : NO
TN3270E_1.
: OFF,
TN3270E_2.
: OFF,
TN3270E_3.
: OFF,
TN3270E_4.
: OFF,
TN3270E_5.
: OFF,
TN3270E_6.
: OFF,
TN3270E_7.
: OFF,
TN3270E_8.
: OFF,
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0,
0,
0,
0,
0,
0,
0,
0,
23,
23,
23,
23,
23,
23,
23,
23,
PR1,
PR2,
PR3,
PR4,
PR5,
PR6,
PR7,
PR8,
1,
2,
3,
4,
5,
6,
7,
8,
AXPR1
AXPR2
AXPR3
AXPR4
AXPR5
AXPR6
AXPR7
AXPR8
--- TN5250E
TN5250E_KA.
TN5250E_1.
TN5250E_2.
TN5250E_3.
TN5250E_4.
TN5250E_5.
TN5250E_6.
TN5250E_7.
TN5250E_8.
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0,
0,
0,
0,
0,
0,
0,
0,
23,
23,
23,
23,
23,
23,
23,
23,
PR1,
PR2,
PR3,
PR4,
PR5,
PR6,
PR7,
PR8,
1,
2,
3,
4,
5,
6,
7,
8,
AXPR1,
AXPR2,
AXPR3,
AXPR4,
AXPR5,
AXPR6,
AXPR7,
AXPR8,
:
:
:
:
:
:
:
:
:
YES
OFF,
OFF,
OFF,
OFF,
OFF,
OFF,
OFF,
OFF,
--- TCP/IP Network Menu
INT_ADDR.
: 192 168 35 62
DEF_ROUT.
: 0 0 0 0
NET_MASK.
: 0 0 0 0
HTTPS_ENB.
: NO
DHCP_ENB.
: YES
AUTOIP_ENB. : YES
BOOTP_ENB.
: YES
RARP_ENB.
: YES
WINS_ENB.
: YES
WINS_ADDR1. : 0 0 0 0
WINS_ADDR2. : 0 0 0 0
NBT_SCOPE_ID. :
DNS_ENB.
: YES
DNS_ADDR1.
: 0 0 0 0
DNS_ADDR2.
: 0 0 0 0
DOMAIN_NAME. :
SLP_ENB.
: YES
SLP_SCOPE_LIST. : DEFAULT
BONJOUR_ENB. : YES
BONJOUR_SRVNAME_LPT1. :
BONJOUR_SRVNAME_USB1. :
SMTP_SERVER. :
FTP_ENB.
: YES
TELNET_ENB. : YES
DEF_IP_FRAME_TYPE. : EthernetII
QSYSOPR,
QSYSOPR,
QSYSOPR,
QSYSOPR,
QSYSOPR,
QSYSOPR,
QSYSOPR,
QSYSOPR,
QSYS
QSYS
QSYS
QSYS
QSYS
QSYS
QSYS
QSYS
(EthernetII, SNAP)
--- TCP/IP Printing Menu
TCP_ENB.
: YES
PAR_TCP_RESTRICT_LIST. :
PROS_PWD.
: netprinter
PROS_PRT.
: 35
LPD_BANN.
: OFF (OFF, AUTO, LAST)
DEFAULT_RAW_TCP. : 9100-9101 (9100-9101, CLOSED)
AXIS 5570e / AXIS 5670e User’s Manual
217
The Parameter List
RTN_OPT.
PPR_PRSTAT.
RTN_PR1.
RTN_PR2.
RTN_PR3.
RTN_PR4.
RTN_PR5.
RTN_PR6.
RTN_PR7.
RTN_PR8.
:
:
:
:
:
:
:
:
:
:
--- SNMP Menu
SNMP_V1_ENB. :
SNMP_V2_ENB. :
READ_COM.
:
WRT_COM.
:
TRAPADDR.
:
TRAP_COM.
:
SYS_NAME.
:
SNMP_AUT.
:
TRAP_PRT.
:
NO
NO
5001, IPDS, 1
0, ASCII, 2
0, ASCII, 3
5011, SCS, 4
5012, SCS, 5
5013, SCS, 6
0, ASCII, 7
0, ASCII, 8
YES
YES
public
pass
0 0 0 0
public
DISABLE
DISABLE
(DISABLE, ENABLE)
(DISABLE, ENABLE)
--- SNMPv3 Menu
SNMP_V3_ENB. : NO
--- NetWare Menu
NETW_ENB.
: YES
NETW_TRANSPORT_PROTOCOL. : DUAL_STACK (IPX_ONLY, IP_ONLY,
DUAL_STACK)
NDPS.
: TCP_AND_SPX (TCP_AND_SPX, TCP_ONLY, SPX_ONLY,
DISABLED)
JOB_CHECK_DELAY. : 5
CONF_CHECK_DELAY. : 300
FR_802_3.
: YES
FR_ETH_2.
: YES
FR_802_2.
: YES
FR_SNAP.
: YES
NCP_BURST_MODE. : YES
PSERVER_NDS_TREE. :
PSERVER_NDS_FILESERVER. :
PSERVER_NDS_DISTINGUISHED_NAME. :
PSERVER_BINDERY1. :
PSERVER_BINDERY2. :
PSERVER_BINDERY3. :
PSERVER_BINDERY4. :
PSERVER_BINDERY5. :
PSERVER_BINDERY6. :
PSERVER_BINDERY7. :
PSERVER_BINDERY8. :
PSERVER_BINDERY9. :
PSERVER_BINDERY10. :
PSERVER_BINDERY11. :
PSERVER_BINDERY12. :
PSERVER_BINDERY13. :
PSERVER_BINDERY14. :
PSERVER_BINDERY15. :
PSERVER_BINDERY16. :
NPRINTER1.
:
NPRINTER2.
:
NPRINTER3.
:
NPRINTER4.
:
218
AXIS 5570e / AXIS 5670e User’s Manual
The Parameter List
NPRINTER5.
NPRINTER6.
NPRINTER7.
NPRINTER8.
:
:
:
:
--- NetBIOS/NetBEUI Menu
LSLM_ENB.
: YES
NB_FR_TYPE. : FR_802_2 (FR_AUTO, FR_802_2, FR_DIX)
LPRINT_1.
: AX181EC4.LP1
LLOGIC_1.
: PR1 (PR1, PR2, PR3, PR4, PR5, PR6, PR7,
LPT1, USB1)
LPRINT_2.
: AX181EC4.US1
LLOGIC_2.
: PR2 (PR1, PR2, PR3, PR4, PR5, PR6, PR7,
LPT1, USB1)
LPRINT_3.
:
LLOGIC_3.
: PR3 (PR1, PR2, PR3, PR4, PR5, PR6, PR7,
LPT1, USB1)
LPRINT_4.
:
LLOGIC_4.
: PR4 (PR1, PR2, PR3, PR4, PR5, PR6, PR7,
LPT1, USB1)
LPRINT_5.
:
LLOGIC_5.
: PR5 (PR1, PR2, PR3, PR4, PR5, PR6, PR7,
LPT1, USB1)
LPRINT_6.
:
LLOGIC_6.
: PR6 (PR1, PR2, PR3, PR4, PR5, PR6, PR7,
LPT1, USB1)
LPRINT_7.
:
LLOGIC_7.
: PR7 (PR1, PR2, PR3, PR4, PR5, PR6, PR7,
LPT1, USB1)
LPRINT_8.
:
LLOGIC_8.
: PR8 (PR1, PR2, PR3, PR4, PR5, PR6, PR7,
LPT1, USB1)
PR8,
PR8,
PR8,
PR8,
PR8,
PR8,
PR8,
PR8,
--- AppleTalk Menu
ATLK_ENB.
: YES
ATK_ZONE.
:
ZONER_EN.
: YES
ATK_FONT.
: DEFAULT (DEFAULT, 35N, ALL)
AUTO_DT_PRIN1. : YES
APRINT_1.
: AXIS181EC4_LPT1
ATYPE_1.
: LaserWriter
ALOGIC_1.
: PR1 (PR1, PR2, PR3, PR4, PR5, PR6, PR7, PR8,
LPT1, USB1)
BINARY_TYPE_1. : TBCP (TBCP, BCP, NONE)
AUTO_DT_PRIN2. : YES
APRINT_2.
: AXIS181EC4_USB1
ATYPE_2.
: LaserWriter
ALOGIC_2.
: PR2 (PR1, PR2, PR3, PR4, PR5, PR6, PR7, PR8,
LPT1, USB1)
BINARY_TYPE_2. : TBCP (TBCP, BCP, NONE)
--- Printer1 Menu
PR1_OUT.
: LPT1 (NONE, LPT1, USB1)
PR1_NAME.
:
PR1_SCND.
: PR1 (PR1, PR2, PR3, PR4, PR5, PR6, PR7, PR8)
PR1_WAIT.
: YES
PR1_IN.
: AUTO (AUTO, NONE)
PR1_BEF.
:
PR1_STR.
:
PR1_CSET.
: NONE (NONE, ISO>IBM, 7UK>IBM, 7SW>IBM, 7GE>IBM,
7FR>IBM, 7ND>IBM, DEC>IBM)
AXIS 5570e / AXIS 5670e User’s Manual
219
The Parameter List
PR1_FILT.
: NONE (NONE, POSTSCR, AUTO_PS)
PR1_AFT.
:
PR1_DUMP.
: NO
PR1_SIZE.
: A4 (A4, LETTER, LEGAL, EXECUT)
PR1_ORNT.
: PORTR (PORTR, LANDS, R_PORTR, R_LANDS)
PR1_FORM.
: 66 0 100 60 30 50
PR1_FONT.
:
PR1_DC_MOD. : NONE (NONE, Canon_GP335, Canon_GP605,
Canon_IR3300, Gestetner_3235, Gestetner_3245, Gestetner_3255,
Gestetner_3265, Gestetner_P7032, HP_LaserJet_5Si,
Konica_Minolta_Pi3502, Konica_Minolta_Pi3505e,
Konica_Minolta_Pi4700e, Konica_Minolta_Pi5500,
Konica_Minolta_Pi5501, Konica_Minolta_Pi6500e,
Konica_Minolta_Pi7200e, Konica_Minolta_Pi7500,
Konica_Minolta_CF2001, Ricoh_Aficio_220, Ricoh_Aficio_270,
Ricoh_Aficio_350, Ricoh_Aficio_450, Ricoh_Aficio_550,
Ricoh_Aficio_650, Ricoh_Aficio_AP4500, Ricoh_Aficio_AP3200,
Savin_9935DP, Savin_9945DP, Savin_9955DP, Savin_9965DP,
Sharp_AR286_FN1, Sharp_AR336_FN1, Sharp_AR405_FN1,
Sharp_AR505_FN1, Sharp_AR286_FN2, Sharp_AR336_FN2,
Sharp_AR405_FN2, Sharp_AR505_FN2, Toshiba_DP_4580,
Toshiba_DP_5570, Toshiba_DP_6570, Toshiba_DP_8070,
Toshiba_eSTUDIO35, Toshiba_eSTUDIO45, Toshiba_eSTUDIO55,
Toshiba_eSTUDIO65, Toshiba_eSTUDIO80, Custom_copier_driver)
PR1_DC_DUP. : OFF (OFF, SIMPLEX, LONG_EDGE_BINDING,
SHORT_EDGE_BINDING)
PR1_DC_STAP. : OFF (OFF, TOP_LEFT_SLANT, TOP_LEFT_HORIZONTAL,
TOP_LEFT_VERTICAL, TOP_RIGHT, BOTTOM_LEFT, BOTTOM_RIGHT,
TOP_DOUBLE, LEFT_DOUBLE, CENTER)
PR1_DC_HOLE. : OFF (OFF, LONG_EDGE, SHORT_EDGE)
PR1_DC_FOLD. : OFF (OFF, HALF_FOLD, Z_FOLD)
PR1_DC_TRAY. : DEFAULT (DEFAULT, 1, 2, 3, 4, 5)
PR1_DC_COP. : 1
--- Printer2 Menu
PR2_OUT.
: USB1 (NONE, LPT1, USB1)
PR2_NAME.
:
PR2_SCND.
: PR2 (PR1, PR2, PR3, PR4, PR5, PR6, PR7, PR8)
PR2_WAIT.
: YES
PR2_IN.
: AUTO (AUTO, NONE)
PR2_BEF.
:
PR2_STR.
:
PR2_CSET.
: NONE (NONE, ISO>IBM, 7UK>IBM, 7SW>IBM, 7GE>IBM,
7FR>IBM, 7ND>IBM, DEC>IBM)
PR2_FILT.
: NONE (NONE, POSTSCR, AUTO_PS)
PR2_AFT.
:
PR2_DUMP.
: NO
PR2_SIZE.
: A4 (A4, LETTER, LEGAL, EXECUT)
PR2_ORNT.
: PORTR (PORTR, LANDS, R_PORTR, R_LANDS)
PR2_FORM.
: 66 0 100 60 30 50
PR2_FONT.
:
PR2_DC_MOD. : NONE (NONE, Canon_GP335, Canon_GP605,
Canon_IR3300, Gestetner_3235, Gestetner_3245, Gestetner_3255,
Gestetner_3265, Gestetner_P7032, HP_LaserJet_5Si,
Konica_Minolta_Pi3502, Konica_Minolta_Pi3505e,
Konica_Minolta_Pi4700e, Konica_Minolta_Pi5500,
Konica_Minolta_Pi5501, Konica_Minolta_Pi6500e,
Konica_Minolta_Pi7200e, Konica_Minolta_Pi7500,
Konica_Minolta_CF2001, Ricoh_Aficio_220, Ricoh_Aficio_270,
Ricoh_Aficio_350, Ricoh_Aficio_450, Ricoh_Aficio_550,
Ricoh_Aficio_650, Ricoh_Aficio_AP4500, Ricoh_Aficio_AP3200,
220
AXIS 5570e / AXIS 5670e User’s Manual
The Parameter List
Savin_9935DP, Savin_9945DP, Savin_9955DP, Savin_9965DP,
Sharp_AR286_FN1, Sharp_AR336_FN1, Sharp_AR405_FN1,
Sharp_AR505_FN1, Sharp_AR286_FN2, Sharp_AR336_FN2,
Sharp_AR405_FN2, Sharp_AR505_FN2, Toshiba_DP_4580,
Toshiba_DP_5570, Toshiba_DP_6570, Toshiba_DP_8070,
Toshiba_eSTUDIO35, Toshiba_eSTUDIO45, Toshiba_eSTUDIO55,
Toshiba_eSTUDIO65, Toshiba_eSTUDIO80, Custom_copier_driver)
PR2_DC_DUP. : OFF (OFF, SIMPLEX, LONG_EDGE_BINDING,
SHORT_EDGE_BINDING)
PR2_DC_STAP. : OFF (OFF, TOP_LEFT_SLANT, TOP_LEFT_HORIZONTAL,
TOP_LEFT_VERTICAL, TOP_RIGHT, BOTTOM_LEFT, BOTTOM_RIGHT,
TOP_DOUBLE, LEFT_DOUBLE, CENTER)
PR2_DC_HOLE. : OFF (OFF, LONG_EDGE, SHORT_EDGE)
PR2_DC_FOLD. : OFF (OFF, HALF_FOLD, Z_FOLD)
PR2_DC_TRAY. : DEFAULT (DEFAULT, 1, 2, 3, 4, 5)
PR2_DC_COP. : 1
--- Printer3 Menu
PR3_OUT.
: LPT1 (NONE, LPT1, USB1)
PR3_NAME.
:
PR3_SCND.
: PR3 (PR1, PR2, PR3, PR4, PR5, PR6, PR7, PR8)
PR3_WAIT.
: YES
PR3_IN.
: AUTO (AUTO, NONE)
PR3_BEF.
:
PR3_STR.
:
PR3_CSET.
: NONE (NONE, ISO>IBM, 7UK>IBM, 7SW>IBM, 7GE>IBM,
7FR>IBM, 7ND>IBM, DEC>IBM)
PR3_FILT.
: NONE (NONE, POSTSCR, AUTO_PS)
PR3_AFT.
:
PR3_DUMP.
: NO
PR3_SIZE.
: A4 (A4, LETTER, LEGAL, EXECUT)
PR3_ORNT.
: PORTR (PORTR, LANDS, R_PORTR, R_LANDS)
PR3_FORM.
: 66 0 100 60 30 50
PR3_FONT.
:
PR3_DC_MOD. : NONE (NONE, Canon_GP335, Canon_GP605,
Canon_IR3300, Gestetner_3235, Gestetner_3245, Gestetner_3255,
Gestetner_3265, Gestetner_P7032, HP_LaserJet_5Si,
Konica_Minolta_Pi3502, Konica_Minolta_Pi3505e,
Konica_Minolta_Pi4700e, Konica_Minolta_Pi5500,
Konica_Minolta_Pi5501, Konica_Minolta_Pi6500e,
Konica_Minolta_Pi7200e, Konica_Minolta_Pi7500,
Konica_Minolta_CF2001, Ricoh_Aficio_220, Ricoh_Aficio_270,
Ricoh_Aficio_350, Ricoh_Aficio_450, Ricoh_Aficio_550,
Ricoh_Aficio_650, Ricoh_Aficio_AP4500, Ricoh_Aficio_AP3200,
Savin_9935DP, Savin_9945DP, Savin_9955DP, Savin_9965DP,
Sharp_AR286_FN1, Sharp_AR336_FN1, Sharp_AR405_FN1,
Sharp_AR505_FN1, Sharp_AR286_FN2, Sharp_AR336_FN2,
Sharp_AR405_FN2, Sharp_AR505_FN2, Toshiba_DP_4580,
Toshiba_DP_5570, Toshiba_DP_6570, Toshiba_DP_8070,
Toshiba_eSTUDIO35, Toshiba_eSTUDIO45, Toshiba_eSTUDIO55,
Toshiba_eSTUDIO65, Toshiba_eSTUDIO80, Custom_copier_driver)
PR3_DC_DUP. : OFF (OFF, SIMPLEX, LONG_EDGE_BINDING,
SHORT_EDGE_BINDING)
PR3_DC_STAP. : OFF (OFF, TOP_LEFT_SLANT, TOP_LEFT_HORIZONTAL,
TOP_LEFT_VERTICAL, TOP_RIGHT, BOTTOM_LEFT, BOTTOM_RIGHT,
TOP_DOUBLE, LEFT_DOUBLE, CENTER)
PR3_DC_HOLE. : OFF (OFF, LONG_EDGE, SHORT_EDGE)
PR3_DC_FOLD. : OFF (OFF, HALF_FOLD, Z_FOLD)
PR3_DC_TRAY. : DEFAULT (DEFAULT, 1, 2, 3, 4, 5)
PR3_DC_COP. : 1
AXIS 5570e / AXIS 5670e User’s Manual
221
The Parameter List
--- Printer4 Menu
PR4_OUT.
: USB1 (NONE, LPT1, USB1)
PR4_NAME.
:
PR4_SCND.
: PR4 (PR1, PR2, PR3, PR4, PR5, PR6, PR7, PR8)
PR4_WAIT.
: YES
PR4_IN.
: AUTO (AUTO, NONE)
PR4_BEF.
:
PR4_STR.
:
PR4_CSET.
: NONE (NONE, ISO>IBM, 7UK>IBM, 7SW>IBM, 7GE>IBM,
7FR>IBM, 7ND>IBM, DEC>IBM)
PR4_FILT.
: NONE (NONE, POSTSCR, AUTO_PS)
PR4_AFT.
:
PR4_DUMP.
: NO
PR4_SIZE.
: A4 (A4, LETTER, LEGAL, EXECUT)
PR4_ORNT.
: PORTR (PORTR, LANDS, R_PORTR, R_LANDS)
PR4_FORM.
: 66 0 100 60 30 50
PR4_FONT.
:
PR4_DC_MOD. : NONE (NONE, Canon_GP335, Canon_GP605,
Canon_IR3300, Gestetner_3235, Gestetner_3245, Gestetner_3255,
Gestetner_3265, Gestetner_P7032, HP_LaserJet_5Si,
Konica_Minolta_Pi3502, Konica_Minolta_Pi3505e,
Konica_Minolta_Pi4700e, Konica_Minolta_Pi5500,
Konica_Minolta_Pi5501, Konica_Minolta_Pi6500e,
Konica_Minolta_Pi7200e, Konica_Minolta_Pi7500,
Konica_Minolta_CF2001, Ricoh_Aficio_220, Ricoh_Aficio_270,
Ricoh_Aficio_350, Ricoh_Aficio_450, Ricoh_Aficio_550,
Ricoh_Aficio_650, Ricoh_Aficio_AP4500, Ricoh_Aficio_AP3200,
Savin_9935DP, Savin_9945DP, Savin_9955DP, Savin_9965DP,
Sharp_AR286_FN1, Sharp_AR336_FN1, Sharp_AR405_FN1,
Sharp_AR505_FN1, Sharp_AR286_FN2, Sharp_AR336_FN2,
Sharp_AR405_FN2, Sharp_AR505_FN2, Toshiba_DP_4580,
Toshiba_DP_5570, Toshiba_DP_6570, Toshiba_DP_8070,
Toshiba_eSTUDIO35, Toshiba_eSTUDIO45, Toshiba_eSTUDIO55,
Toshiba_eSTUDIO65, Toshiba_eSTUDIO80, Custom_copier_driver)
PR4_DC_DUP. : OFF (OFF, SIMPLEX, LONG_EDGE_BINDING,
SHORT_EDGE_BINDING)
PR4_DC_STAP. : OFF (OFF, TOP_LEFT_SLANT, TOP_LEFT_HORIZONTAL,
TOP_LEFT_VERTICAL, TOP_RIGHT, BOTTOM_LEFT, BOTTOM_RIGHT,
TOP_DOUBLE, LEFT_DOUBLE, CENTER)
PR4_DC_HOLE. : OFF (OFF, LONG_EDGE, SHORT_EDGE)
PR4_DC_FOLD. : OFF (OFF, HALF_FOLD, Z_FOLD)
PR4_DC_TRAY. : DEFAULT (DEFAULT, 1, 2, 3, 4, 5)
PR4_DC_COP. : 1
--- Printer5 Menu
PR5_OUT.
: LPT1 (NONE, LPT1, USB1)
PR5_NAME.
:
PR5_SCND.
: PR5 (PR1, PR2, PR3, PR4, PR5, PR6, PR7, PR8)
PR5_WAIT.
: YES
PR5_IN.
: AUTO (AUTO, NONE)
PR5_BEF.
:
PR5_STR.
:
PR5_CSET.
: NONE (NONE, ISO>IBM, 7UK>IBM, 7SW>IBM, 7GE>IBM,
7FR>IBM, 7ND>IBM, DEC>IBM)
PR5_FILT.
: NONE (NONE, POSTSCR, AUTO_PS)
PR5_AFT.
:
PR5_DUMP.
: NO
PR5_SIZE.
: A4 (A4, LETTER, LEGAL, EXECUT)
PR5_ORNT.
: PORTR (PORTR, LANDS, R_PORTR, R_LANDS)
PR5_FORM.
: 66 0 100 60 30 50
PR5_FONT.
:
222
AXIS 5570e / AXIS 5670e User’s Manual
The Parameter List
PR5_DC_MOD. : NONE (NONE, Canon_GP335, Canon_GP605,
Canon_IR3300, Gestetner_3235, Gestetner_3245, Gestetner_3255,
Gestetner_3265, Gestetner_P7032, HP_LaserJet_5Si,
Konica_Minolta_Pi3502, Konica_Minolta_Pi3505e,
Konica_Minolta_Pi4700e, Konica_Minolta_Pi5500,
Konica_Minolta_Pi5501, Konica_Minolta_Pi6500e,
Konica_Minolta_Pi7200e, Konica_Minolta_Pi7500,
Konica_Minolta_CF2001, Ricoh_Aficio_220, Ricoh_Aficio_270,
Ricoh_Aficio_350, Ricoh_Aficio_450, Ricoh_Aficio_550,
Ricoh_Aficio_650, Ricoh_Aficio_AP4500, Ricoh_Aficio_AP3200,
Savin_9935DP, Savin_9945DP, Savin_9955DP, Savin_9965DP,
Sharp_AR286_FN1, Sharp_AR336_FN1, Sharp_AR405_FN1,
Sharp_AR505_FN1, Sharp_AR286_FN2, Sharp_AR336_FN2,
Sharp_AR405_FN2, Sharp_AR505_FN2, Toshiba_DP_4580,
Toshiba_DP_5570, Toshiba_DP_6570, Toshiba_DP_8070,
Toshiba_eSTUDIO35, Toshiba_eSTUDIO45, Toshiba_eSTUDIO55,
Toshiba_eSTUDIO65, Toshiba_eSTUDIO80, Custom_copier_driver)
PR5_DC_DUP. : OFF (OFF, SIMPLEX, LONG_EDGE_BINDING,
SHORT_EDGE_BINDING)
PR5_DC_STAP. : OFF (OFF, TOP_LEFT_SLANT, TOP_LEFT_HORIZONTAL,
TOP_LEFT_VERTICAL, TOP_RIGHT, BOTTOM_LEFT, BOTTOM_RIGHT,
TOP_DOUBLE, LEFT_DOUBLE, CENTER)
PR5_DC_HOLE. : OFF (OFF, LONG_EDGE, SHORT_EDGE)
PR5_DC_FOLD. : OFF (OFF, HALF_FOLD, Z_FOLD)
PR5_DC_TRAY. : DEFAULT (DEFAULT, 1, 2, 3, 4, 5)
PR5_DC_COP. : 1
--- Printer6 Menu
PR6_OUT.
: USB1 (NONE, LPT1, USB1)
PR6_NAME.
:
PR6_SCND.
: PR6 (PR1, PR2, PR3, PR4, PR5, PR6, PR7, PR8)
PR6_WAIT.
: YES
PR6_IN.
: AUTO (AUTO, NONE)
PR6_BEF.
:
PR6_STR.
:
PR6_CSET.
: NONE (NONE, ISO>IBM, 7UK>IBM, 7SW>IBM, 7GE>IBM,
7FR>IBM, 7ND>IBM, DEC>IBM)
PR6_FILT.
: NONE (NONE, POSTSCR, AUTO_PS)
PR6_AFT.
:
PR6_DUMP.
: NO
PR6_SIZE.
: A4 (A4, LETTER, LEGAL, EXECUT)
PR6_ORNT.
: PORTR (PORTR, LANDS, R_PORTR, R_LANDS)
PR6_FORM.
: 66 0 100 60 30 50
PR6_FONT.
:
PR6_DC_MOD. : NONE (NONE, Canon_GP335, Canon_GP605,
Canon_IR3300, Gestetner_3235, Gestetner_3245, Gestetner_3255,
Gestetner_3265, Gestetner_P7032, HP_LaserJet_5Si,
Konica_Minolta_Pi3502, Konica_Minolta_Pi3505e,
Konica_Minolta_Pi4700e, Konica_Minolta_Pi5500,
Konica_Minolta_Pi5501, Konica_Minolta_Pi6500e,
Konica_Minolta_Pi7200e, Konica_Minolta_Pi7500,
Konica_Minolta_CF2001, Ricoh_Aficio_220, Ricoh_Aficio_270,
Ricoh_Aficio_350, Ricoh_Aficio_450, Ricoh_Aficio_550,
Ricoh_Aficio_650, Ricoh_Aficio_AP4500, Ricoh_Aficio_AP3200,
Savin_9935DP, Savin_9945DP, Savin_9955DP, Savin_9965DP,
Sharp_AR286_FN1, Sharp_AR336_FN1, Sharp_AR405_FN1,
Sharp_AR505_FN1, Sharp_AR286_FN2, Sharp_AR336_FN2,
Sharp_AR405_FN2, Sharp_AR505_FN2, Toshiba_DP_4580,
Toshiba_DP_5570, Toshiba_DP_6570, Toshiba_DP_8070,
Toshiba_eSTUDIO35, Toshiba_eSTUDIO45, Toshiba_eSTUDIO55,
Toshiba_eSTUDIO65, Toshiba_eSTUDIO80, Custom_copier_driver)
AXIS 5570e / AXIS 5670e User’s Manual
223
The Parameter List
PR6_DC_DUP. : OFF (OFF, SIMPLEX, LONG_EDGE_BINDING,
SHORT_EDGE_BINDING)
PR6_DC_STAP. : OFF (OFF, TOP_LEFT_SLANT, TOP_LEFT_HORIZONTAL,
TOP_LEFT_VERTICAL, TOP_RIGHT, BOTTOM_LEFT, BOTTOM_RIGHT,
TOP_DOUBLE, LEFT_DOUBLE, CENTER)
PR6_DC_HOLE. : OFF (OFF, LONG_EDGE, SHORT_EDGE)
PR6_DC_FOLD. : OFF (OFF, HALF_FOLD, Z_FOLD)
PR6_DC_TRAY. : DEFAULT (DEFAULT, 1, 2, 3, 4, 5)
PR6_DC_COP. : 1
--- Printer7 Menu
PR7_OUT.
: LPT1 (NONE, LPT1, USB1)
PR7_NAME.
:
PR7_SCND.
: PR7 (PR1, PR2, PR3, PR4, PR5, PR6, PR7, PR8)
PR7_WAIT.
: YES
PR7_IN.
: AUTO (AUTO, NONE)
PR7_BEF.
:
PR7_STR.
:
PR7_CSET.
: NONE (NONE, ISO>IBM, 7UK>IBM, 7SW>IBM, 7GE>IBM,
7FR>IBM, 7ND>IBM, DEC>IBM)
PR7_FILT.
: NONE (NONE, POSTSCR, AUTO_PS)
PR7_AFT.
:
PR7_DUMP.
: NO
PR7_SIZE.
: A4 (A4, LETTER, LEGAL, EXECUT)
PR7_ORNT.
: PORTR (PORTR, LANDS, R_PORTR, R_LANDS)
PR7_FORM.
: 66 0 100 60 30 50
PR7_FONT.
:
PR7_DC_MOD. : NONE (NONE, Canon_GP335, Canon_GP605,
Canon_IR3300, Gestetner_3235, Gestetner_3245, Gestetner_3255,
Gestetner_3265, Gestetner_P7032, HP_LaserJet_5Si,
Konica_Minolta_Pi3502, Konica_Minolta_Pi3505e,
Konica_Minolta_Pi4700e, Konica_Minolta_Pi5500,
Konica_Minolta_Pi5501, Konica_Minolta_Pi6500e,
Konica_Minolta_Pi7200e, Konica_Minolta_Pi7500,
Konica_Minolta_CF2001, Ricoh_Aficio_220, Ricoh_Aficio_270,
Ricoh_Aficio_350, Ricoh_Aficio_450, Ricoh_Aficio_550,
Ricoh_Aficio_650, Ricoh_Aficio_AP4500, Ricoh_Aficio_AP3200,
Savin_9935DP, Savin_9945DP, Savin_9955DP, Savin_9965DP,
Sharp_AR286_FN1, Sharp_AR336_FN1, Sharp_AR405_FN1,
Sharp_AR505_FN1, Sharp_AR286_FN2, Sharp_AR336_FN2,
Sharp_AR405_FN2, Sharp_AR505_FN2, Toshiba_DP_4580,
Toshiba_DP_5570, Toshiba_DP_6570, Toshiba_DP_8070,
Toshiba_eSTUDIO35, Toshiba_eSTUDIO45, Toshiba_eSTUDIO55,
Toshiba_eSTUDIO65, Toshiba_eSTUDIO80, Custom_copier_driver)
PR7_DC_DUP. : OFF (OFF, SIMPLEX, LONG_EDGE_BINDING,
SHORT_EDGE_BINDING)
PR7_DC_STAP. : OFF (OFF, TOP_LEFT_SLANT, TOP_LEFT_HORIZONTAL,
TOP_LEFT_VERTICAL, TOP_RIGHT, BOTTOM_LEFT, BOTTOM_RIGHT,
TOP_DOUBLE, LEFT_DOUBLE, CENTER)
PR7_DC_HOLE. : OFF (OFF, LONG_EDGE, SHORT_EDGE)
PR7_DC_FOLD. : OFF (OFF, HALF_FOLD, Z_FOLD)
PR7_DC_TRAY. : DEFAULT (DEFAULT, 1, 2, 3, 4, 5)
PR7_DC_COP. : 1
--- Printer8
PR8_OUT.
PR8_NAME.
PR8_SCND.
PR8_WAIT.
PR8_IN.
PR8_BEF.
224
Menu
: USB1 (NONE, LPT1, USB1)
:
: PR8 (PR1, PR2, PR3, PR4, PR5, PR6, PR7, PR8)
: YES
: AUTO (AUTO, NONE)
:
AXIS 5570e / AXIS 5670e User’s Manual
The Parameter List
PR8_STR.
:
PR8_CSET.
: NONE (NONE, ISO>IBM, 7UK>IBM, 7SW>IBM, 7GE>IBM,
7FR>IBM, 7ND>IBM, DEC>IBM)
PR8_FILT.
: NONE (NONE, POSTSCR, AUTO_PS)
PR8_AFT.
:
PR8_DUMP.
: NO
PR8_SIZE.
: A4 (A4, LETTER, LEGAL, EXECUT)
PR8_ORNT.
: PORTR (PORTR, LANDS, R_PORTR, R_LANDS)
PR8_FORM.
: 66 0 100 60 30 50
PR8_FONT.
:
PR8_DC_MOD. : NONE (NONE, Canon_GP335, Canon_GP605,
Canon_IR3300, Gestetner_3235, Gestetner_3245, Gestetner_3255,
Gestetner_3265, Gestetner_P7032, HP_LaserJet_5Si,
Konica_Minolta_Pi3502, Konica_Minolta_Pi3505e,
Konica_Minolta_Pi4700e, Konica_Minolta_Pi5500,
Konica_Minolta_Pi5501, Konica_Minolta_Pi6500e,
Konica_Minolta_Pi7200e, Konica_Minolta_Pi7500,
Konica_Minolta_CF2001, Ricoh_Aficio_220, Ricoh_Aficio_270,
Ricoh_Aficio_350, Ricoh_Aficio_450, Ricoh_Aficio_550,
Ricoh_Aficio_650, Ricoh_Aficio_AP4500, Ricoh_Aficio_AP3200,
Savin_9935DP, Savin_9945DP, Savin_9955DP, Savin_9965DP,
Sharp_AR286_FN1, Sharp_AR336_FN1, Sharp_AR405_FN1,
Sharp_AR505_FN1, Sharp_AR286_FN2, Sharp_AR336_FN2,
Sharp_AR405_FN2, Sharp_AR505_FN2, Toshiba_DP_4580,
Toshiba_DP_5570, Toshiba_DP_6570, Toshiba_DP_8070,
Toshiba_eSTUDIO35, Toshiba_eSTUDIO45, Toshiba_eSTUDIO55,
Toshiba_eSTUDIO65, Toshiba_eSTUDIO80, Custom_copier_driver)
PR8_DC_DUP. : OFF (OFF, SIMPLEX, LONG_EDGE_BINDING,
SHORT_EDGE_BINDING)
PR8_DC_STAP. : OFF (OFF, TOP_LEFT_SLANT, TOP_LEFT_HORIZONTAL,
TOP_LEFT_VERTICAL, TOP_RIGHT, BOTTOM_LEFT, BOTTOM_RIGHT,
TOP_DOUBLE, LEFT_DOUBLE, CENTER)
PR8_DC_HOLE. : OFF (OFF, LONG_EDGE, SHORT_EDGE)
PR8_DC_FOLD. : OFF (OFF, HALF_FOLD, Z_FOLD)
PR8_DC_TRAY. : DEFAULT (DEFAULT, 1, 2, 3, 4, 5)
PR8_DC_COP. : 1
--- DC General Menu
PAR_CUST_DC_CTRL_NAME. :
--- DC PCL Control Menu
PAR_CUST_DC_PCL_CTRL_METHOD. : PCL
PS_PJL)
PAR_CUST_DC_PCL_CTRL_ENTER. :
PAR_CUST_DC_PCL_CTRL_POSTSCRIPT. :
PAR_CUST_DC_PCL_CTRL_PCL. :
PAR_CUST_DC_PCL_CTRL_PCLXL. :
PAR_CUST_DC_PCL_CTRL_EXIT. :
(None, PS, PJL, PCL,
--- DC PCL Duplex Menu
PAR_CUST_DC_PCL_DUP_SIMPLEX. :
PAR_CUST_DC_PCL_DUP_LONG. :
PAR_CUST_DC_PCL_DUP_SHORT. :
--- DC PCL Staple Menu
PAR_CUST_DC_PCL_STP_TOP_L_SLN. :
PAR_CUST_DC_PCL_STP_TOP_L_HOR. :
PAR_CUST_DC_PCL_STP_TOP_L_VER. :
PAR_CUST_DC_PCL_STP_TOP_RIGHT. :
PAR_CUST_DC_PCL_STP_LOW_LEFT. :
PAR_CUST_DC_PCL_STP_LOW_RIGHT. :
AXIS 5570e / AXIS 5670e User’s Manual
225
The Parameter List
PAR_CUST_DC_PCL_STP_TOP_2. :
PAR_CUST_DC_PCL_STP_LEFT_2. :
PAR_CUST_DC_PCL_STP_MID_2. :
--- DC PCL Punch Menu
PAR_CUST_DC_PCL_PUNCH_LONG. :
PAR_CUST_DC_PCL_PUNCH_SHORT. :
--- DC PCL Fold Menu
PAR_CUST_DC_PCL_FOLD_HALF. :
PAR_CUST_DC_PCL_FOLD_Z. :
--- DC PCL Media Menu
PAR_CUST_DC_PCL_MEDIA_DEFAULT. :
PAR_CUST_DC_PCL_MEDIA_TRAY1. :
PAR_CUST_DC_PCL_MEDIA_TRAY2. :
PAR_CUST_DC_PCL_MEDIA_TRAY3. :
PAR_CUST_DC_PCL_MEDIA_TRAY4. :
PAR_CUST_DC_PCL_MEDIA_TRAY5. :
--- DC PCL Copies Menu
PAR_CUST_DC_PCL_COPIES_LEAD. :
PAR_CUST_DC_PCL_COPIES_TRAILER. :
--- DC PS Control Menu
PAR_CUST_DC_PS_CTRL_METHOD. : PS (None, PS, PJL, PCL, PS_PJL)
PAR_CUST_DC_PS_CTRL_ENTER. :
PAR_CUST_DC_PS_CTRL_POSTSCRIPT. :
PAR_CUST_DC_PS_CTRL_PCL. :
PAR_CUST_DC_PS_CTRL_PCLXL. :
PAR_CUST_DC_PS_CTRL_EXIT. :
--- DC PS Duplex Menu
PAR_CUST_DC_PS_DUP_SIMPLEX. :
PAR_CUST_DC_PS_DUP_LONG. :
PAR_CUST_DC_PS_DUP_SHORT. :
--- DC PS Staple Menu
PAR_CUST_DC_PS_STP_TOP_L_SLN. :
PAR_CUST_DC_PS_STP_TOP_L_HOR. :
PAR_CUST_DC_PS_STP_TOP_L_VER. :
PAR_CUST_DC_PS_STP_TOP_RIGHT. :
PAR_CUST_DC_PS_STP_LOW_LEFT. :
PAR_CUST_DC_PS_STP_LOW_RIGHT. :
PAR_CUST_DC_PS_STP_TOP_2. :
PAR_CUST_DC_PS_STP_LEFT_2. :
PAR_CUST_DC_PS_STP_MID_2. :
--- DC PS Punch Menu
PAR_CUST_DC_PS_PUNCH_LONG. :
PAR_CUST_DC_PS_PUNCH_SHORT. :
--- DC PS Fold Menu
PAR_CUST_DC_PS_FOLD_HALF. :
PAR_CUST_DC_PS_FOLD_Z. :
--- DC PS Media Menu
PAR_CUST_DC_PS_MEDIA_DEFAULT. :
PAR_CUST_DC_PS_MEDIA_TRAY1. :
PAR_CUST_DC_PS_MEDIA_TRAY2. :
PAR_CUST_DC_PS_MEDIA_TRAY3. :
226
AXIS 5570e / AXIS 5670e User’s Manual
The Parameter List
PAR_CUST_DC_PS_MEDIA_TRAY4. :
PAR_CUST_DC_PS_MEDIA_TRAY5. :
--- DC PS Copies Menu
PAR_CUST_DC_PS_COPIES_LEAD. :
PAR_CUST_DC_PS_COPIES_TRAILER. :
--- LPT1 Menu
L1_CENTR.
: HISPEED (IBM_PC, STNDRD, FAST, HISPEED, HINOACK,
ECP)
L1_BSYTM.
: 60
L1_MGM_INFO. : AUTO (DISABLE, AUTO)
L1_COMMENT. :
L1_BIDIR.
: AUTO (DISABLE, AUTO)
L1_READT.
: 3
--- USB1 Menu
U1_MGM_INFO. : AUTO (DISABLE, AUTO)
U1_COMMENT. :
U1_BIDIR.
: AUTO (DISABLE, AUTO)
U1_READT.
: 3
U1_BUFFER_SIZE. : 0
U1_PORT_STATUS_OVERRIDE. : NO
--- IBM IPDS Configuration
IPDS_COLSUP. : Disabled
IPDS_DUPSUP. : Enabled
IPDS_OPTDUP. : Enabled
IPDS_RAF.
: Disabled
IPDS_NUP.
: 1-up (1-up, 2-up, 4-up)
IPDS_OVLXOFF. : 0
IPDS_OVLYOFF. : 0
IPDS_RPTXOFF. : 0
IPDS_RPTYOFF. : 0
IPDS_DOB.
: Bin1 (Bin1, Bin2, Bin3, Bin4, Bin5, Bin6)
IPDS_DIB.
: Bin1 (Bin1, Bin2, Bin3, Bin4, Bin5)
PS_IPLINK.
: Off (Off, Sheet, Bin)
IPDS_BIN1.
: Letter, 0, 0
IPDS_BIN2.
: Letter, 0, 0
IPDS_BIN3.
: Letter, 0, 0
IPDS_BIN4.
: Letter, 0, 0
IPDS_BIN5.
: Letter, 0, 0
--- IBM IPDS
PS_LFSM.
PS_ERRH.
PS_OPTOVL.
PS_G4SUP.
PS_VM.
PS_BIN1.
PS_BIN2.
PS_BIN3.
PS_BIN4.
PS_BIN5.
PS_DEST.
PostScript
: Enabled
: Disabled
: Enabled
: Disabled
: 2000
: Default,
: Default,
: Default,
: Default,
: Default,
: 0, 0, 0,
Driver Settings
100, 100,
100, 100,
100, 100,
100, 100,
100, 100,
0, 0, 0
0,
0,
0,
0,
0,
0
0
0
0
0
--- IBM IPDS PCL Driver Settings
PCL_VER.
: 5 (3, 4, 5)
PCL_SBSET.
: AUTOMATIC (AUTOMATIC, US-ASCII, Latin1, Latin5,
Latin9, PC437, PC850, PC852, Roman8, ISO8859-7)
PCL_OCR_ENB. : Enabled
AXIS 5570e / AXIS 5670e User’s Manual
227
The Parameter List
PCL_OPTOVL.
PCL_BIN1.
PCL_BIN2.
PCL_BIN3.
PCL_BIN4.
PCL_BIN5.
PCL_DEST.
:
:
:
:
:
:
:
Disabled
8, 0, 0
1, 0, 0
4, 0, 0
5, 0, 0
0, 0, 0
0, 0, 0, 0, 0, 0
--- IBM EMULATOR 1
IPDS_PREMUL1. : IPDS_4332 (IPDS_4224_C2, IPDS_4224_E3,
IPDS_3812_2, IPDS_3812_2_00, IPDS_3816, IPDS_4028_1,
IPDS_4028_2, IPDS_4312, IPDS_4317, IPDS_4324, IPDS_4332)
IPDS_PRRES1. : 0
IPDS_SYSL1. : 37 (37, 256, 259, 260, 273, 274, 275, 277, 278,
280, 281, 282, 284, 285, 286, 287, 288, 289, 290, 293, 297, 361,
420, 423, 424, 437, 500, 803, 819, 838, 852, 853, 857, 858, 860,
861, 863, 865, 870, 871, 875, 880, 892, 893, 905, 912, 914, 920,
923, 924, 1004, 1026, 1069, 1140, 1141, 1142, 1143, 1144, 1145,
1146, 1147, 1148, 1149, 1252)
IPDS_PD1.
: PostScript (PostScript, PCL)
IPDS_SOJS1. :
IPDS_EOJS1. :
PREMUL1.
: 3816_CX (3287_CX, 3268_CX, 3262_CX, 4214_CX,
4224_CX, 4230_CX, 3812_CX, 3816S_CX, 3816_CX, 5224_TX, 5225_TX,
5256_TX, 4214_TX, 4230_TX, 3812_TX, 3816S_TX, 3816_TX,
5X27_001_TX, 5X27_002_KS_TX, 5X27_002_KSSM_TX, 5X27_003_TX,
5X27_005_TX)
SYSL1.
: 37 (37, 256, 260, 273, 274, 275, 277, 278, 280,
281, 282, 284, 285, 286, 287, 288, 289, 290, 293, 297, 340, 361,
423, 500, 833, 836, 838, 870, 871, 875, 892, 893, 1026, 1140,
1141, 1142, 1143, 1144, 1145, 1146, 1147, 1148, 1149, USER)
PASSTHR1.
: NO
MPL1.
: 66, ENA
MPP1.
: 132, ENA
LPI1.
: 6 (3, 4, 6, 8)
CPI1.
: 10 (5, 10, 12, 13.3, 15, 17, 18)
DCPI1.
: 5.0 (5.0, 6.0, 6.7, 7.5, 9.0)
AUTORI1.
: YES
LM1.
: 0, 0, 48
TM1.
: 26, 26, 74
LDSF1.
: 100, 100, 70
DEFBIN1.
: BIN1 (BIN1, BIN2, BIN3, BIN4, BIN5, BIN6,
MANUAL, ENVELOPE, CONTINUOUS)
PRDRIVER1.
: PCL5 (USER, GENERIC, PCL4, PCL5, IBM_PRO,
EPSON_FX, EPSON_FX_15CPI, EPSON_LQ, EPSON_LQ_8LPI,
EPSON_LQ_1600K, EPSON_LQ_KS)
--- IBM EMULATOR 2
IPDS_PREMUL2. : IPDS_4332 (IPDS_4224_C2, IPDS_4224_E3,
IPDS_3812_2, IPDS_3812_2_00, IPDS_3816, IPDS_4028_1,
IPDS_4028_2, IPDS_4312, IPDS_4317, IPDS_4324, IPDS_4332)
IPDS_PRRES2. : 0
IPDS_SYSL2. : 37 (37, 256, 259, 260, 273, 274, 275, 277, 278,
280, 281, 282, 284, 285, 286, 287, 288, 289, 290, 293, 297, 361,
420, 423, 424, 437, 500, 803, 819, 838, 852, 853, 857, 858, 860,
861, 863, 865, 870, 871, 875, 880, 892, 893, 905, 912, 914, 920,
923, 924, 1004, 1026, 1069, 1140, 1141, 1142, 1143, 1144, 1145,
1146, 1147, 1148, 1149, 1252)
IPDS_PD2.
: PostScript (PostScript, PCL)
IPDS_SOJS2. :
IPDS_EOJS2. :
228
AXIS 5570e / AXIS 5670e User’s Manual
The Parameter List
PREMUL2.
: 3816_CX (3287_CX, 3268_CX, 3262_CX, 4214_CX,
4224_CX, 4230_CX, 3812_CX, 3816S_CX, 3816_CX, 5224_TX, 5225_TX,
5256_TX, 4214_TX, 4230_TX, 3812_TX, 3816S_TX, 3816_TX,
5X27_001_TX, 5X27_002_KS_TX, 5X27_002_KSSM_TX, 5X27_003_TX,
5X27_005_TX)
SYSL2.
: 37 (37, 256, 260, 273, 274, 275, 277, 278, 280,
281, 282, 284, 285, 286, 287, 288, 289, 290, 293, 297, 340, 361,
423, 500, 833, 836, 838, 870, 871, 875, 892, 893, 1026, 1140,
1141, 1142, 1143, 1144, 1145, 1146, 1147, 1148, 1149, USER)
PASSTHR2.
: NO
MPL2.
: 66, ENA
MPP2.
: 132, ENA
LPI2.
: 6 (3, 4, 6, 8)
CPI2.
: 10 (5, 10, 12, 13.3, 15, 17, 18)
DCPI2.
: 5.0 (5.0, 6.0, 6.7, 7.5, 9.0)
AUTORI2.
: YES
LM2.
: 0, 0, 48
TM2.
: 26, 26, 74
LDSF2.
: 100, 100, 70
DEFBIN2.
: BIN1 (BIN1, BIN2, BIN3, BIN4, BIN5, BIN6,
MANUAL, ENVELOPE, CONTINUOUS)
PRDRIVER2.
: PCL5 (USER, GENERIC, PCL4, PCL5, IBM_PRO,
EPSON_FX, EPSON_FX_15CPI, EPSON_LQ, EPSON_LQ_8LPI,
EPSON_LQ_1600K, EPSON_LQ_KS)
--- IBM EMULATOR 3
IPDS_PREMUL3. : IPDS_4332 (IPDS_4224_C2, IPDS_4224_E3,
IPDS_3812_2, IPDS_3812_2_00, IPDS_3816, IPDS_4028_1,
IPDS_4028_2, IPDS_4312, IPDS_4317, IPDS_4324, IPDS_4332)
IPDS_PRRES3. : 0
IPDS_SYSL3. : 37 (37, 256, 259, 260, 273, 274, 275, 277, 278,
280, 281, 282, 284, 285, 286, 287, 288, 289, 290, 293, 297, 361,
420, 423, 424, 437, 500, 803, 819, 838, 852, 853, 857, 858, 860,
861, 863, 865, 870, 871, 875, 880, 892, 893, 905, 912, 914, 920,
923, 924, 1004, 1026, 1069, 1140, 1141, 1142, 1143, 1144, 1145,
1146, 1147, 1148, 1149, 1252)
IPDS_PD3.
: PostScript (PostScript, PCL)
IPDS_SOJS3. :
IPDS_EOJS3. :
PREMUL3.
: 3816_CX (3287_CX, 3268_CX, 3262_CX, 4214_CX,
4224_CX, 4230_CX, 3812_CX, 3816S_CX, 3816_CX, 5224_TX, 5225_TX,
5256_TX, 4214_TX, 4230_TX, 3812_TX, 3816S_TX, 3816_TX,
5X27_001_TX, 5X27_002_KS_TX, 5X27_002_KSSM_TX, 5X27_003_TX,
5X27_005_TX)
SYSL3.
: 37 (37, 256, 260, 273, 274, 275, 277, 278, 280,
281, 282, 284, 285, 286, 287, 288, 289, 290, 293, 297, 340, 361,
423, 500, 833, 836, 838, 870, 871, 875, 892, 893, 1026, 1140,
1141, 1142, 1143, 1144, 1145, 1146, 1147, 1148, 1149, USER)
PASSTHR3.
: NO
MPL3.
: 66, ENA
MPP3.
: 132, ENA
LPI3.
: 6 (3, 4, 6, 8)
CPI3.
: 10 (5, 10, 12, 13.3, 15, 17, 18)
DCPI3.
: 5.0 (5.0, 6.0, 6.7, 7.5, 9.0)
AUTORI3.
: YES
LM3.
: 0, 0, 48
TM3.
: 26, 26, 74
LDSF3.
: 100, 100, 70
DEFBIN3.
: BIN1 (BIN1, BIN2, BIN3, BIN4, BIN5, BIN6,
MANUAL, ENVELOPE, CONTINUOUS)
AXIS 5570e / AXIS 5670e User’s Manual
229
The Parameter List
PRDRIVER3.
: PCL5 (USER, GENERIC, PCL4, PCL5, IBM_PRO,
EPSON_FX, EPSON_FX_15CPI, EPSON_LQ, EPSON_LQ_8LPI,
EPSON_LQ_1600K, EPSON_LQ_KS)
--- IBM EMULATOR 4
IPDS_PREMUL4. : IPDS_4332 (IPDS_4224_C2, IPDS_4224_E3,
IPDS_3812_2, IPDS_3812_2_00, IPDS_3816, IPDS_4028_1,
IPDS_4028_2, IPDS_4312, IPDS_4317, IPDS_4324, IPDS_4332)
IPDS_PRRES4. : 0
IPDS_SYSL4. : 37 (37, 256, 259, 260, 273, 274, 275, 277, 278,
280, 281, 282, 284, 285, 286, 287, 288, 289, 290, 293, 297, 361,
420, 423, 424, 437, 500, 803, 819, 838, 852, 853, 857, 858, 860,
861, 863, 865, 870, 871, 875, 880, 892, 893, 905, 912, 914, 920,
923, 924, 1004, 1026, 1069, 1140, 1141, 1142, 1143, 1144, 1145,
1146, 1147, 1148, 1149, 1252)
IPDS_PD4.
: PostScript (PostScript, PCL)
IPDS_SOJS4. :
IPDS_EOJS4. :
PREMUL4.
: 3816_CX (3287_CX, 3268_CX, 3262_CX, 4214_CX,
4224_CX, 4230_CX, 3812_CX, 3816S_CX, 3816_CX, 5224_TX, 5225_TX,
5256_TX, 4214_TX, 4230_TX, 3812_TX, 3816S_TX, 3816_TX,
5X27_001_TX, 5X27_002_KS_TX, 5X27_002_KSSM_TX, 5X27_003_TX,
5X27_005_TX)
SYSL4.
: 37 (37, 256, 260, 273, 274, 275, 277, 278, 280,
281, 282, 284, 285, 286, 287, 288, 289, 290, 293, 297, 340, 361,
423, 500, 833, 836, 838, 870, 871, 875, 892, 893, 1026, 1140,
1141, 1142, 1143, 1144, 1145, 1146, 1147, 1148, 1149, USER)
PASSTHR4.
: NO
MPL4.
: 66, ENA
MPP4.
: 132, ENA
LPI4.
: 6 (3, 4, 6, 8)
CPI4.
: 10 (5, 10, 12, 13.3, 15, 17, 18)
DCPI4.
: 5.0 (5.0, 6.0, 6.7, 7.5, 9.0)
AUTORI4.
: YES
LM4.
: 0, 0, 48
TM4.
: 26, 26, 74
LDSF4.
: 100, 100, 70
DEFBIN4.
: BIN1 (BIN1, BIN2, BIN3, BIN4, BIN5, BIN6,
MANUAL, ENVELOPE, CONTINUOUS)
PRDRIVER4.
: PCL5 (USER, GENERIC, PCL4, PCL5, IBM_PRO,
EPSON_FX, EPSON_FX_15CPI, EPSON_LQ, EPSON_LQ_8LPI,
EPSON_LQ_1600K, EPSON_LQ_KS)
--- IBM EMULATOR 5
IPDS_PREMUL5. : IPDS_4332 (IPDS_4224_C2, IPDS_4224_E3,
IPDS_3812_2, IPDS_3812_2_00, IPDS_3816, IPDS_4028_1,
IPDS_4028_2, IPDS_4312, IPDS_4317, IPDS_4324, IPDS_4332)
IPDS_PRRES5. : 0
IPDS_SYSL5. : 37 (37, 256, 259, 260, 273, 274, 275, 277, 278,
280, 281, 282, 284, 285, 286, 287, 288, 289, 290, 293, 297, 361,
420, 423, 424, 437, 500, 803, 819, 838, 852, 853, 857, 858, 860,
861, 863, 865, 870, 871, 875, 880, 892, 893, 905, 912, 914, 920,
923, 924, 1004, 1026, 1069, 1140, 1141, 1142, 1143, 1144, 1145,
1146, 1147, 1148, 1149, 1252)
IPDS_PD5.
: PostScript (PostScript, PCL)
IPDS_SOJS5. :
IPDS_EOJS5. :
230
AXIS 5570e / AXIS 5670e User’s Manual
The Parameter List
PREMUL5.
: 3816_CX (3287_CX, 3268_CX, 3262_CX, 4214_CX,
4224_CX, 4230_CX, 3812_CX, 3816S_CX, 3816_CX, 5224_TX, 5225_TX,
5256_TX, 4214_TX, 4230_TX, 3812_TX, 3816S_TX, 3816_TX,
5X27_001_TX, 5X27_002_KS_TX, 5X27_002_KSSM_TX, 5X27_003_TX,
5X27_005_TX)
SYSL5.
: 37 (37, 256, 260, 273, 274, 275, 277, 278, 280,
281, 282, 284, 285, 286, 287, 288, 289, 290, 293, 297, 340, 361,
423, 500, 833, 836, 838, 870, 871, 875, 892, 893, 1026, 1140,
1141, 1142, 1143, 1144, 1145, 1146, 1147, 1148, 1149, USER)
PASSTHR5.
: NO
MPL5.
: 66, ENA
MPP5.
: 132, ENA
LPI5.
: 6 (3, 4, 6, 8)
CPI5.
: 10 (5, 10, 12, 13.3, 15, 17, 18)
DCPI5.
: 5.0 (5.0, 6.0, 6.7, 7.5, 9.0)
AUTORI5.
: YES
LM5.
: 0, 0, 48
TM5.
: 26, 26, 74
LDSF5.
: 100, 100, 70
DEFBIN5.
: BIN1 (BIN1, BIN2, BIN3, BIN4, BIN5, BIN6,
MANUAL, ENVELOPE, CONTINUOUS)
PRDRIVER5.
: PCL5 (USER, GENERIC, PCL4, PCL5, IBM_PRO,
EPSON_FX, EPSON_FX_15CPI, EPSON_LQ, EPSON_LQ_8LPI,
EPSON_LQ_1600K, EPSON_LQ_KS)
--- IBM EMULATOR 6
IPDS_PREMUL6. : IPDS_4332 (IPDS_4224_C2, IPDS_4224_E3,
IPDS_3812_2, IPDS_3812_2_00, IPDS_3816, IPDS_4028_1,
IPDS_4028_2, IPDS_4312, IPDS_4317, IPDS_4324, IPDS_4332)
IPDS_PRRES6. : 0
IPDS_SYSL6. : 37 (37, 256, 259, 260, 273, 274, 275, 277, 278,
280, 281, 282, 284, 285, 286, 287, 288, 289, 290, 293, 297, 361,
420, 423, 424, 437, 500, 803, 819, 838, 852, 853, 857, 858, 860,
861, 863, 865, 870, 871, 875, 880, 892, 893, 905, 912, 914, 920,
923, 924, 1004, 1026, 1069, 1140, 1141, 1142, 1143, 1144, 1145,
1146, 1147, 1148, 1149, 1252)
IPDS_PD6.
: PostScript (PostScript, PCL)
IPDS_SOJS6. :
IPDS_EOJS6. :
PREMUL6.
: 3816_CX (3287_CX, 3268_CX, 3262_CX, 4214_CX,
4224_CX, 4230_CX, 3812_CX, 3816S_CX, 3816_CX, 5224_TX, 5225_TX,
5256_TX, 4214_TX, 4230_TX, 3812_TX, 3816S_TX, 3816_TX,
5X27_001_TX, 5X27_002_KS_TX, 5X27_002_KSSM_TX, 5X27_003_TX,
5X27_005_TX)
SYSL6.
: 37 (37, 256, 260, 273, 274, 275, 277, 278, 280,
281, 282, 284, 285, 286, 287, 288, 289, 290, 293, 297, 340, 361,
423, 500, 833, 836, 838, 870, 871, 875, 892, 893, 1026, 1140,
1141, 1142, 1143, 1144, 1145, 1146, 1147, 1148, 1149, USER)
PASSTHR6.
: NO
MPL6.
: 66, ENA
MPP6.
: 132, ENA
LPI6.
: 6 (3, 4, 6, 8)
CPI6.
: 10 (5, 10, 12, 13.3, 15, 17, 18)
DCPI6.
: 5.0 (5.0, 6.0, 6.7, 7.5, 9.0)
AUTORI6.
: YES
LM6.
: 0, 0, 48
TM6.
: 26, 26, 74
LDSF6.
: 100, 100, 70
DEFBIN6.
: BIN1 (BIN1, BIN2, BIN3, BIN4, BIN5, BIN6,
MANUAL, ENVELOPE, CONTINUOUS)
AXIS 5570e / AXIS 5670e User’s Manual
231
The Parameter List
PRDRIVER6.
: PCL5 (USER, GENERIC, PCL4, PCL5, IBM_PRO,
EPSON_FX, EPSON_FX_15CPI, EPSON_LQ, EPSON_LQ_8LPI,
EPSON_LQ_1600K, EPSON_LQ_KS)
--- IBM EMULATOR 7
IPDS_PREMUL7. : IPDS_4332 (IPDS_4224_C2, IPDS_4224_E3,
IPDS_3812_2, IPDS_3812_2_00, IPDS_3816, IPDS_4028_1,
IPDS_4028_2, IPDS_4312, IPDS_4317, IPDS_4324, IPDS_4332)
IPDS_PRRES7. : 0
IPDS_SYSL7. : 37 (37, 256, 259, 260, 273, 274, 275, 277, 278,
280, 281, 282, 284, 285, 286, 287, 288, 289, 290, 293, 297, 361,
420, 423, 424, 437, 500, 803, 819, 838, 852, 853, 857, 858, 860,
861, 863, 865, 870, 871, 875, 880, 892, 893, 905, 912, 914, 920,
923, 924, 1004, 1026, 1069, 1140, 1141, 1142, 1143, 1144, 1145,
1146, 1147, 1148, 1149, 1252)
IPDS_PD7.
: PostScript (PostScript, PCL)
IPDS_SOJS7. :
IPDS_EOJS7. :
PREMUL7.
: 3816_CX (3287_CX, 3268_CX, 3262_CX, 4214_CX,
4224_CX, 4230_CX, 3812_CX, 3816S_CX, 3816_CX, 5224_TX, 5225_TX,
5256_TX, 4214_TX, 4230_TX, 3812_TX, 3816S_TX, 3816_TX,
5X27_001_TX, 5X27_002_KS_TX, 5X27_002_KSSM_TX, 5X27_003_TX,
5X27_005_TX)
SYSL7.
: 37 (37, 256, 260, 273, 274, 275, 277, 278, 280,
281, 282, 284, 285, 286, 287, 288, 289, 290, 293, 297, 340, 361,
423, 500, 833, 836, 838, 870, 871, 875, 892, 893, 1026, 1140,
1141, 1142, 1143, 1144, 1145, 1146, 1147, 1148, 1149, USER)
PASSTHR7.
: NO
MPL7.
: 66, ENA
MPP7.
: 132, ENA
LPI7.
: 6 (3, 4, 6, 8)
CPI7.
: 10 (5, 10, 12, 13.3, 15, 17, 18)
DCPI7.
: 5.0 (5.0, 6.0, 6.7, 7.5, 9.0)
AUTORI7.
: YES
LM7.
: 0, 0, 48
TM7.
: 26, 26, 74
LDSF7.
: 100, 100, 70
DEFBIN7.
: BIN1 (BIN1, BIN2, BIN3, BIN4, BIN5, BIN6,
MANUAL, ENVELOPE, CONTINUOUS)
PRDRIVER7.
: PCL5 (USER, GENERIC, PCL4, PCL5, IBM_PRO,
EPSON_FX, EPSON_FX_15CPI, EPSON_LQ, EPSON_LQ_8LPI,
EPSON_LQ_1600K, EPSON_LQ_KS)
--- IBM EMULATOR 8
IPDS_PREMUL8. : IPDS_4332 (IPDS_4224_C2, IPDS_4224_E3,
IPDS_3812_2, IPDS_3812_2_00, IPDS_3816, IPDS_4028_1,
IPDS_4028_2, IPDS_4312, IPDS_4317, IPDS_4324, IPDS_4332)
IPDS_PRRES8. : 0
IPDS_SYSL8. : 37 (37, 256, 259, 260, 273, 274, 275, 277, 278,
280, 281, 282, 284, 285, 286, 287, 288, 289, 290, 293, 297, 361,
420, 423, 424, 437, 500, 803, 819, 838, 852, 853, 857, 858, 860,
861, 863, 865, 870, 871, 875, 880, 892, 893, 905, 912, 914, 920,
923, 924, 1004, 1026, 1069, 1140, 1141, 1142, 1143, 1144, 1145,
1146, 1147, 1148, 1149, 1252)
IPDS_PD8.
: PostScript (PostScript, PCL)
IPDS_SOJS8. :
IPDS_EOJS8. :
232
AXIS 5570e / AXIS 5670e User’s Manual
The Parameter List
PREMUL8.
: 3816_CX (3287_CX, 3268_CX, 3262_CX, 4214_CX,
4224_CX, 4230_CX, 3812_CX, 3816S_CX, 3816_CX, 5224_TX, 5225_TX,
5256_TX, 4214_TX, 4230_TX, 3812_TX, 3816S_TX, 3816_TX,
5X27_001_TX, 5X27_002_KS_TX, 5X27_002_KSSM_TX, 5X27_003_TX,
5X27_005_TX)
SYSL8.
: 37 (37, 256, 260, 273, 274, 275, 277, 278, 280,
281, 282, 284, 285, 286, 287, 288, 289, 290, 293, 297, 340, 361,
423, 500, 833, 836, 838, 870, 871, 875, 892, 893, 1026, 1140,
1141, 1142, 1143, 1144, 1145, 1146, 1147, 1148, 1149, USER)
PASSTHR8.
: NO
MPL8.
: 66, ENA
MPP8.
: 132, ENA
LPI8.
: 6 (3, 4, 6, 8)
CPI8.
: 10 (5, 10, 12, 13.3, 15, 17, 18)
DCPI8.
: 5.0 (5.0, 6.0, 6.7, 7.5, 9.0)
AUTORI8.
: YES
LM8.
: 0, 0, 48
TM8.
: 26, 26, 74
LDSF8.
: 100, 100, 70
DEFBIN8.
: BIN1 (BIN1, BIN2, BIN3, BIN4, BIN5, BIN6,
MANUAL, ENVELOPE, CONTINUOUS)
PRDRIVER8.
: PCL5 (USER, GENERIC, PCL4, PCL5, IBM_PRO,
EPSON_FX, EPSON_FX_15CPI, EPSON_LQ, EPSON_LQ_8LPI,
EPSON_LQ_1600K, EPSON_LQ_KS)
--- IBM SCS PAGE FORMAT
PCORI.
: NO
DWSISO.
: NO
BIN1.
: COR, LETTER,
BIN2.
: COR, LETTER,
BIN3.
: COR, LETTER,
BIN4.
: COR, LETTER,
BIN5.
: COR, LETTER,
BIN6.
: COR, LETTER,
MANUAL.
: COR, LETTER,
ENVELOPE.
: COR, LETTER,
CONTINUOUS. : COR, LETTER,
SIMBF.
: YES
0,
0,
0,
0,
0,
0,
0,
0,
0,
0
0
0
0
0
0
0
0
0
--- IBM SCS CPI MAPPING
FGID_DEFAULT. : 11
FGID_CPI5.
: 244, 11
FGID_CPI10. : 11, 204
FGID_CPI12. : 86, 230
FGID_CPI15. : 230, 281
FGID_CPI17. : 252, 281
FGID_CPI8COR. : 86
FGID_CPI20COR. : 281
FGID_CPI25COR. : 289
FGID_CPI27COR. : 290
PROPOCOR.
: 230
TYPOCOR.
: 230
--- IBM SCS JOB CONTROL
REINIT.
: YES
SUPFFBLANK. : NO
--- IBM 3270 OPTIONS
CASE.
: DUAL (DUAL, MONO)
BASCOL.
: BLACK, ENA
XSTRN.
: 0
AXIS 5570e / AXIS 5670e User’s Manual
233
The Parameter List
AUTNL.
ADDNL.
FFWPB.
FFEOPB.
NULSUP.
FFCPOS.
AFEOPB.
:
:
:
:
:
:
:
1
1
0
1
0
0
0
--- IBM SCS EXTENDED EMULATION
XEMUL.
: YES
WARN.
: NO
SSUBST.
: YES
SBTS.
:
TLIS.
: 025 03C
TTRS.
: 03E 025
FLIS.
: 025 02F
EECS.
: 025 041 058 049 053
COBXEM.
: SETALL (OFF, SETESC, SETALL)
CCLIS.
: 025 050
--- UDS
--------- BAR
NUMBER TYPE WIDTH HEIGHT TEXT-MODE CHECK-MODE
--------------------------------------------------------------- SSTR
---------- MSTR
---------- IBM PRINTER DRIVER
PRDRIVERBASE. : PCL5 (GENERIC, PCL4, PCL5, IBM_PRO, EPSON_FX,
EPSON_FX_15CPI, EPSON_LQ, EPSON_LQ_8LPI, EPSON_LQ_1600K,
EPSON_LQ_KS)
SOJS.
: 1B 45 1B 26 6C 30 4C
EOJS.
: 1B 45
BACKSPS.
: 08
CRS.
: 0D
LFS.
: 0A
NLS.
: 0D 0A
FFS.
: 0C
SOS.
:
SIS.
:
BLKS.
:
GRNS.
:
BLUS.
:
REDS.
:
MAGS.
:
CYNS.
:
YELS.
:
BIN1S.
: 1B 26 6C 31 48
BIN2S.
: 1B 26 6C 34 48
BIN3S.
: 1B 26 6C 35 48
BIN4S.
: 1B 26 6C 32 30 48
BIN5S.
: 1B 26 6C 32 31 48
BIN6S.
: 1B 26 6C 32 32 48
MANUALS.
: 1B 26 6C 32 48
ENVELOPES.
: 1B 26 6C 36 48
CONTINUOUSS. : 1B 26 6C 31 48
234
AXIS 5570e / AXIS 5670e User’s Manual
The Parameter List
CSIZS.
:
LAC.
: HP_PCL (DISABLE, HP_PCL, EPSON_LQ)
GRD.
: HP_PCL (DISABLE, HP_PCL, EPSON_LQ)
JOGS.
: 1B 26 6C 31 54
SSUS.
:
SBSET.
: PC850 (ECMA94, ISO8859-7, LATIN9, PC437, PC850,
PC852, PC857, PC858, PC869, PC874, PC891, PC903, PC904, PC942,
ROMAN8, USASCII, USER)
--- FONT
FGID CSSF SBSET SPACING PITCH HEIGHT STYLE
STROKE TYPEFACE STRING
--------------------------------------------------------------------------------FONT.
: 3,
98, DEFAULT,FIXED, 100, 0,
UPRIGHT,MEDIUM,4102,
1B 28 31 4F
FONT.
: 5,
98, DEFAULT,FIXED, 100, 0,
UPRIGHT,MEDIUM,4102,
FONT.
: 11,
98, DEFAULT,FIXED, 100, 0,
UPRIGHT,MEDIUM,4099,
FONT.
: 12,
98, DEFAULT,FIXED, 100, 0,
UPRIGHT,MEDIUM,4099,
FONT.
: 13,
98, DEFAULT,FIXED, 100, 0,
UPRIGHT,MEDIUM,4099,
FONT.
: 18,
98, DEFAULT,FIXED, 100, 0,
ITALIC,MEDIUM,4099,
FONT.
: 19,
98, DEFAULT,FIXED, 100, 0,
UPRIGHT,MEDIUM,4200,
1B 28 30 4F
FONT.
: 20,
98, DEFAULT,FIXED, 100, 0,
UPRIGHT,MEDIUM,4099,
FONT.
: 30,
98, DEFAULT,FIXED, 100, 0,
UPRIGHT,MEDIUM,4099,
FONT.
: 38,
98, DEFAULT,FIXED, 100, 0,
UPRIGHT,BOLD, 4102,
FONT.
: 39,
98, DEFAULT,FIXED, 135, 0,
UPRIGHT,BOLD, 4102,
FONT.
: 40,
98, DEFAULT,FIXED, 135, 0,
UPRIGHT,MEDIUM,4102,
FONT.
: 41,
98, DEFAULT,FIXED, 100, 0,
UPRIGHT,MEDIUM,4099,
FONT.
: 42,
98, DEFAULT,FIXED, 100, 0,
UPRIGHT,MEDIUM,4099,
FONT.
: 43,
98, DEFAULT,FIXED, 100, 0,
ITALIC,MEDIUM,4099,
FONT.
: 46,
98, DEFAULT,FIXED, 100, 0,
UPRIGHT,BOLD, 4099,
FONT.
: 60,
98, DEFAULT,FIXED, 100, 0,
UPRIGHT,BOLD, 4099,
FONT.
: 66,
98, DEFAULT,FIXED, 150, 0,
UPRIGHT,MEDIUM,4102,
FONT.
: 68,
98, DEFAULT,FIXED, 150, 0,
ITALIC,MEDIUM,4102,
FONT.
: 69,
98, DEFAULT,FIXED, 150, 0,
UPRIGHT,BOLD, 4102,
FONT.
: 70,
98, DEFAULT,FIXED, 120, 0,
UPRIGHT,MEDIUM,4099,
FONT.
: 71,
98, DEFAULT,FIXED, 120, 0,
ITALIC,MEDIUM,4099,
FONT.
: 72,
98, DEFAULT,FIXED, 120, 0,
UPRIGHT,BOLD, 4099,
FONT.
: 80,
98, DEFAULT,FIXED, 120, 0,
UPRIGHT,MEDIUM,4099,
AXIS 5570e / AXIS 5670e User’s Manual
235
The Parameter List
FONT.
: 84,
UPRIGHT,MEDIUM,4099,
FONT.
: 85,
UPRIGHT,MEDIUM,4099,
FONT.
: 86,
UPRIGHT,MEDIUM,4099,
FONT.
: 87,
UPRIGHT,MEDIUM,4102,
FONT.
: 91,
ITALIC,MEDIUM,4099,
FONT.
: 108,
UPRIGHT,BOLD, 4099,
FONT.
: 110,
UPRIGHT,BOLD, 4102,
FONT.
: 111,
UPRIGHT,BOLD, 4099,
FONT.
: 112,
ITALIC,MEDIUM,4099,
FONT.
: 155,
ITALIC,BOLD, 4101,
FONT.
: 158,
UPRIGHT,MEDIUM,4101,
FONT.
: 159,
UPRIGHT,BOLD, 4101,
FONT.
: 160,
UPRIGHT,MEDIUM,4148,
FONT.
: 162,
ITALIC,MEDIUM,4148,
FONT.
: 163,
UPRIGHT,BOLD, 4148,
FONT.
: 173,
UPRIGHT,LIGHT, 4148,
FONT.
: 175,
UPRIGHT,MEDIUM,4101,
FONT.
: 204,
UPRIGHT,MEDIUM,4102,
FONT.
: 221,
UPRIGHT,MEDIUM,4099,
FONT.
: 223,
UPRIGHT,MEDIUM,4099,
FONT.
: 225,
UPRIGHT,MEDIUM,4099,
FONT.
: 229,
UPRIGHT,MEDIUM,4099,
FONT.
: 230,
UPRIGHT,MEDIUM,4102,
FONT.
: 244,
UPRIGHT,MEDIUM,4099,
FONT.
: 245,
UPRIGHT,BOLD, 4099,
FONT.
: 252,
UPRIGHT,MEDIUM,4099,
FONT.
: 253,
UPRIGHT,BOLD, 4099,
FONT.
: 254,
UPRIGHT,MEDIUM,4099,
FONT.
: 258,
UPRIGHT,MEDIUM,4099,
FONT.
: 266,
UPRIGHT,BOLD, 4099,
236
98,
DEFAULT,FIXED,
120,
0,
98,
DEFAULT,FIXED,
120,
0,
98,
DEFAULT,FIXED,
120,
0,
98,
DEFAULT,FIXED,
130,
0,
98,
DEFAULT,FIXED,
120,
0,
98,
DEFAULT,FIXED,
120,
0,
98,
DEFAULT,FIXED,
130,
0,
98,
DEFAULT,FIXED,
120,
0,
98,
DEFAULT,FIXED,
120,
0,
100, DEFAULT,PROP,
0,
110,
100, DEFAULT,PROP,
0,
110,
100, DEFAULT,PROP,
0,
110,
100, DEFAULT,PROP,
0,
110,
100, DEFAULT,PROP,
0,
110,
100, DEFAULT,PROP,
0,
110,
100, DEFAULT,PROP,
0,
110,
100, DEFAULT,PROP,
0,
110,
98,
DEFAULT,FIXED,
167,
0,
98,
DEFAULT,FIXED,
150,
0,
98,
DEFAULT,FIXED,
150,
0,
98,
DEFAULT,FIXED,
150,
0,
98,
DEFAULT,FIXED,
150,
0,
98,
DEFAULT,FIXED,
180,
0,
98,
DEFAULT,FIXED,
100,
0,
98,
DEFAULT,FIXED,
100,
0,
98,
DEFAULT,FIXED,
171,
0,
98,
DEFAULT,FIXED,
171,
0,
98,
DEFAULT,FIXED,
220,
0,
98,
DEFAULT,FIXED,
180,
0,
98,
DEFAULT,FIXED,
100,
0,
AXIS 5570e / AXIS 5670e User’s Manual
The Parameter List
FONT.
: 281,
UPRIGHT,MEDIUM,4102,
FONT.
: 289,
UPRIGHT,MEDIUM,4102,
FONT.
: 290,
UPRIGHT,MEDIUM,4102,
FONT.
: 751,
UPRIGHT,MEDIUM,4101,
FONT.
: 1051,
UPRIGHT,MEDIUM,4101,
FONT.
: 1053,
UPRIGHT,BOLD, 4101,
FONT.
: 1056,
ITALIC,MEDIUM,4101,
FONT.
: 1351,
UPRIGHT,MEDIUM,4101,
FONT.
: 1653,
UPRIGHT,BOLD, 4101,
FONT.
: 2103,
UPRIGHT,BOLD, 4101,
FONT.
: 3840,
UPRIGHT,MEDIUM,4101,
FONT.
: 3841,
UPRIGHT,BOLD, 4101,
FONT.
: 3842,
ITALIC,MEDIUM,4101,
FONT.
: 3843,
ITALIC,BOLD, 4101,
FONT.
: 3844,
UPRIGHT,MEDIUM,4113,
FONT.
: 3845,
UPRIGHT,BOLD, 4113,
FONT.
: 3846,
ITALIC,MEDIUM,4113,
FONT.
: 3847,
ITALIC,BOLD, 4113,
FONT.
: 3848,
ITALIC,MEDIUM,4116,
FONT.
: 3849,
MEDIUM,4140,
1B
28 73
FONT.
: 3850,
UPRIGHT,MEDIUM,4148,
FONT.
: 3851,
UPRIGHT,BOLD, 4148,
FONT.
: 3852,
ITALIC,MEDIUM,4148,
FONT.
: 3853,
ITALIC,BOLD, 4148,
FONT.
: 3854,
MEDIUM,4148,
1B
28 73
FONT.
: 3855,
BOLD, 4148,
1B
28 73
FONT.
: 3856,
MEDIUM,4148,
1B
28 73
FONT.
: 3857,
BOLD, 4148,
1B
28 73
AXIS 5570e / AXIS 5670e User’s Manual
98,
DEFAULT,FIXED,
233,
0,
98,
DEFAULT,FIXED,
267,
0,
98,
DEFAULT,FIXED,
300,
0,
100, DEFAULT,PROP,
0,
80,
100, DEFAULT,PROP,
0,
100,
100, DEFAULT,PROP,
0,
100,
100, DEFAULT,PROP,
0,
100,
100, DEFAULT,PROP,
0,
120,
100, DEFAULT,PROP,
0,
160,
100, DEFAULT,PROP,
0,
240,
100, DEFAULT,PROP,
0,
0,
100, DEFAULT,PROP,
0,
0,
100, DEFAULT,PROP,
0,
0,
100, DEFAULT,PROP,
0,
0,
100, DEFAULT,PROP,
0,
0,
100, DEFAULT,PROP,
0,
0,
100, DEFAULT,PROP,
0,
0,
100, DEFAULT,PROP,
0,
0,
100, DEFAULT,PROP,
0,
0,
100, DEFAULT,PROP,
0,
0,
34 53
100, DEFAULT,PROP,
0,
0,
100, DEFAULT,PROP,
0,
0,
100, DEFAULT,PROP,
0,
0,
100, DEFAULT,PROP,
0,
0,
100, DEFAULT,PROP,
0,
0,
NONE,
34 53
100, DEFAULT,PROP,
0,
0,
NONE,
34 53
100, DEFAULT,PROP,
0,
0,
NONE,
35 53
100, DEFAULT,PROP,
0,
0,
NONE,
NONE,
35 53
237
The Parameter List
FONT.
: 3858, 100, DEFAULT,PROP,
UPRIGHT,MEDIUM,4168,
FONT.
: 3859, 100, DEFAULT,PROP,
UPRIGHT,BOLD, 4168,
FONT.
: 3860, 100, DEFAULT,PROP,
ITALIC,MEDIUM,4168,
FONT.
: 3861, 100, DEFAULT,PROP,
UPRIGHT,MEDIUM,4197,
FONT.
: 3862, 100, DEFAULT,PROP,
UPRIGHT,BOLD, 4197,
FONT.
: 3863, 100, DEFAULT,PROP,
ITALIC,MEDIUM,4197,
FONT.
: 3864, 100, DEFAULT,PROP,
ITALIC,BOLD, 4197,
FONT.
: 3865, 100, DEFAULT,PROP,
UPRIGHT,MEDIUM,4297,
FONT.
: 3866, 100, DEFAULT,PROP,
UPRIGHT,NONE, 4362,
1B 28 73 31 42
FONT.
: 3867, 100, DEFAULT,PROP,
UPRIGHT,NONE, 4362,
1B 28 73 34 42
FONT.
: 3868, 100, DEFAULT,PROP,
UPRIGHT,MEDIUM,16602,
FONT.
: 3869, 100, DEFAULT,PROP,
UPRIGHT,BOLD, 16602,
FONT.
: 3870, 100, DEFAULT,PROP,
ITALIC,MEDIUM,16602,
FONT.
: 3871, 100, DEFAULT,PROP,
ITALIC,BOLD, 16602,
FONT.
: 3872, 100, DEFAULT,PROP,
UPRIGHT,MEDIUM,16901,
FONT.
: 3873, 100, DEFAULT,PROP,
UPRIGHT,BOLD, 16901,
FONT.
: 3874, 100, DEFAULT,PROP,
ITALIC,MEDIUM,16901,
FONT.
: 3875, 100, DEFAULT,PROP,
ITALIC,BOLD, 16901,
FONT.
: 3876, 100, DEFAULT,PROP,
UPRIGHT,MEDIUM,16686,
1B 28 31 39 4D
FONT.
: 3877, 100, DEFAULT,PROP,
UPRIGHT,MEDIUM,31402,
1B 28 35 37 39 4C
FONT.
: 5687, 100, DEFAULT,PROP,
UPRIGHT,MEDIUM,16901,
FONT.
: 5707, 100, DEFAULT,PROP,
UPRIGHT,BOLD, 16901,
FONT.
: 5815, 100, DEFAULT,PROP,
ITALIC,MEDIUM,16901,
FONT.
: 5835, 100, DEFAULT,PROP,
ITALIC,BOLD, 16901,
FONT.
: 6199, 100, DEFAULT,PROP,
UPRIGHT,MEDIUM,4197,
FONT.
: 6219, 100, DEFAULT,PROP,
UPRIGHT,BOLD, 4197,
FONT.
: 6327, 100, DEFAULT,PROP,
ITALIC,MEDIUM,4197,
FONT.
: 6347, 100, DEFAULT,PROP,
ITALIC,BOLD, 4197,
FONT.
: 16951,100, DEFAULT,PROP,
UPRIGHT,MEDIUM,4101,
FONT.
: 16971,100, DEFAULT,PROP,
UPRIGHT,BOLD, 4101,
238
0,
0,
0,
0,
0,
0,
0,
0,
0,
0,
0,
0,
0,
0,
0,
0,
0,
0,
0,
0,
0,
0,
0,
0,
0,
0,
0,
0,
0,
0,
0,
0,
0,
0,
0,
0,
0,
0,
0,
0,
0,
0,
0,
0,
0,
0,
0,
0,
0,
0,
0,
0,
0,
0,
0,
0,
0,
0,
0,
0,
AXIS 5570e / AXIS 5670e User’s Manual
The Parameter List
FONT.
: 17079,100, DEFAULT,PROP,
0,
ITALIC,MEDIUM,4101,
FONT.
: 17099,100, DEFAULT,PROP,
0,
ITALIC,BOLD, 4101,
FONT.
: 33335,100, DEFAULT,PROP,
0,
UPRIGHT,MEDIUM,4113,
FONT.
: 33355,100, DEFAULT,PROP,
0,
UPRIGHT,BOLD, 4113,
FONT.
: 33463,100, DEFAULT,PROP,
0,
ITALIC,MEDIUM,4113,
FONT.
: 33483,100, DEFAULT,PROP,
0,
ITALIC,BOLD, 4113,
FONT.
: 33591,100, DEFAULT,PROP,
0,
UPRIGHT,MEDIUM,16602,
FONT.
: 33601,100, DEFAULT,PROP,
0,
UPRIGHT,BOLD, 16602,
FONT.
: 33719,100, DEFAULT,PROP,
0,
ITALIC,MEDIUM,16602,
FONT.
: 33729,100, DEFAULT,PROP,
0,
ITALIC,BOLD, 16602,
FONT.
: 34103,100, DEFAULT,PROP,
0,
UPRIGHT,MEDIUM,4148,
FONT.
: 34123,100, DEFAULT,PROP,
0,
UPRIGHT,BOLD, 4148,
FONT.
: 34231,100, DEFAULT,PROP,
0,
ITALIC,MEDIUM,4148,
FONT.
: 34251,100, DEFAULT,PROP,
0,
ITALIC,BOLD, 4148,
FONT.
: 41783,100, DEFAULT,PROP,
0,
UPRIGHT,MEDIUM,4116,
FONT.
: 41803,100, DEFAULT,PROP,
0,
UPRIGHT,BOLD, 4116,
FONT.
: 41911,100, DEFAULT,PROP,
0,
ITALIC,MEDIUM,4116,
FONT.
: 41931,100, DEFAULT,PROP,
0,
ITALIC,BOLD, 4116,
FONT.
: 50000,100, PC942,PROP,
0,
UPRIGHT,MEDIUM,28752,
1B
28 31 39 4B 1B 26 74 33 31 50
FONT.
: 50001,100, PC942,PROP,
0,
UPRIGHT,MEDIUM,28752,
1B
28 31 39 4B 1B 26 74 33 31 50
FONT.
: 50002,100, PC942,PROP,
0,
UPRIGHT,MEDIUM,28752,
1B
28 31 39 4B 1B 26 74 33 31 50
FONT.
: 50003,100, PC942,PROP,
0,
UPRIGHT,MEDIUM,28752,
1B
28 31 39 4B 1B 26 74 33 31 50
FONT.
: 50004,100, PC942,PROP,
0,
UPRIGHT,MEDIUM,28752,
1B
28 31 39 4B 1B 26 74 33 31 50
FONT.
: 50005,100, PC942,PROP,
0,
UPRIGHT,MEDIUM,28752,
1B
28 31 39 4B 1B 26 74 33 31 50
FONT.
: 50006,100, PC942,PROP,
0,
UPRIGHT,MEDIUM,28752,
1B
28 31 39 4B 1B 26 74 33 31 50
FONT.
: 50007,100, PC942,PROP,
0,
UPRIGHT,MEDIUM,28752,
1B
28 31 39 4B 1B 26 74 33 31 50
AXIS 5570e / AXIS 5670e User’s Manual
0,
0,
0,
0,
0,
0,
0,
0,
0,
0,
0,
0,
0,
0,
0,
0,
0,
0,
144,
144,
120,
108,
96,
96,
80,
101,
239
The Parameter List
FONT.
: 50008,100, PC942,PROP,
UPRIGHT,MEDIUM,28752,
1B
28 31 39 4B 1B 26 74 33
FONT.
: 50009,100, PC942,PROP,
UPRIGHT,MEDIUM,28752,
1B
28 31 39 4B 1B 26 74 33
FONT.
: 50010,100, PC942,PROP,
UPRIGHT,MEDIUM,28752,
1B
28 31 39 4B 1B 26 74 33
FONT.
: 50011,100, PC942,PROP,
UPRIGHT,MEDIUM,28752,
1B
28 31 39 4B 1B 26 74 33
FONT.
: 50012,100, PC942,PROP,
UPRIGHT,MEDIUM,28752,
1B
28 31 39 4B 1B 26 74 33
FONT.
: 50013,100, PC942,PROP,
UPRIGHT,MEDIUM,28752,
1B
28 31 39 4B 1B 26 74 33
FONT.
: 50014,100, PC942,PROP,
UPRIGHT,MEDIUM,28752,
1B
28 31 39 4B 1B 26 74 33
FONT.
: 50015,100, PC942,PROP,
UPRIGHT,MEDIUM,28752,
1B
28 31 39 4B 1B 26 74 33
FONT.
: 50016,100, PC942,PROP,
UPRIGHT,MEDIUM,28752,
1B
28 31 39 4B 1B 26 74 33
FONT.
: 50017,100, PC942,PROP,
UPRIGHT,MEDIUM,28752,
1B
28 31 39 4B 1B 26 74 33
FONT.
: 50018,100, PC942,PROP,
UPRIGHT,MEDIUM,28752,
1B
28 31 39 4B 1B 26 74 33
FONT.
: 50019,100, PC942,PROP,
UPRIGHT,MEDIUM,28752,
1B
28 31 39 4B 1B 26 74 33
FONT.
: 50020,100, PC942,PROP,
UPRIGHT,MEDIUM,28752,
1B
28 31 39 4B 1B 26 74 33
FONT.
: 50021,100, PC942,PROP,
UPRIGHT,MEDIUM,28752,
1B
28 31 39 4B 1B 26 74 33
FONT.
: 50022,100, PC942,PROP,
UPRIGHT,MEDIUM,28752,
1B
28 31 39 4B 1B 26 74 33
FONT.
: 50023,100, PC942,PROP,
UPRIGHT,MEDIUM,28752,
1B
28 31 39 4B 1B 26 74 33
FONT.
: 50030,100, PC891,PROP,
UPRIGHT,MEDIUM,43088,
1B
28 31 39 48 1B 26 74 33
FONT.
: 50031,100, PC891,PROP,
UPRIGHT,MEDIUM,43088,
1B
28 31 39 48 1B 26 74 33
FONT.
: 50032,100, PC891,PROP,
UPRIGHT,MEDIUM,43088,
1B
28 31 39 48 1B 26 74 33
FONT.
: 50033,100, PC891,PROP,
UPRIGHT,MEDIUM,43088,
1B
28 31 39 48 1B 26 74 33
240
0,
101,
31 50
0,
84,
31 50
0,
76,
31 50
0,
67,
31 50
0,
67,
31 50
0,
56,
31 50
0,
144,
31 50
0,
120,
31 50
0,
108,
31 50
0,
96,
31 50
0,
80,
31 50
0,
101,
31 50
0,
84,
31 50
0,
76,
31 50
0,
67,
31 50
0,
56,
31 50
0,
144,
38 50
0,
144,
38 50
0,
120,
38 50
0,
108,
38 50
AXIS 5570e / AXIS 5670e User’s Manual
The Parameter List
FONT.
: 50034,100, PC891,PROP,
UPRIGHT,MEDIUM,43088,
1B
28 31 39 48 1B 26 74 33
FONT.
: 50035,100, PC891,PROP,
UPRIGHT,MEDIUM,43088,
1B
28 31 39 48 1B 26 74 33
FONT.
: 50036,100, PC891,PROP,
UPRIGHT,MEDIUM,43088,
1B
28 31 39 48 1B 26 74 33
FONT.
: 50037,100, PC891,PROP,
UPRIGHT,MEDIUM,43088,
1B
28 31 39 48 1B 26 74 33
FONT.
: 50038,100, PC891,PROP,
UPRIGHT,MEDIUM,43088,
1B
28 31 39 48 1B 26 74 33
FONT.
: 50039,100, PC891,PROP,
UPRIGHT,MEDIUM,43088,
1B
28 31 39 48 1B 26 74 33
FONT.
: 50040,100, PC891,PROP,
UPRIGHT,MEDIUM,43088,
1B
28 31 39 48 1B 26 74 33
FONT.
: 50041,100, PC891,PROP,
UPRIGHT,MEDIUM,43088,
1B
28 31 39 48 1B 26 74 33
FONT.
: 50042,100, PC891,PROP,
UPRIGHT,MEDIUM,43088,
1B
28 31 39 48 1B 26 74 33
FONT.
: 50043,100, PC891,PROP,
UPRIGHT,MEDIUM,43088,
1B
28 31 39 48 1B 26 74 33
FONT.
: 50044,100, PC891,PROP,
UPRIGHT,MEDIUM,41040,
1B
28 31 39 48 1B 26 74 33
FONT.
: 50045,100, PC891,PROP,
UPRIGHT,MEDIUM,41040,
1B
28 31 39 48 1B 26 74 33
FONT.
: 50046,100, PC891,PROP,
UPRIGHT,MEDIUM,41040,
1B
28 31 39 48 1B 26 74 33
FONT.
: 50047,100, PC891,PROP,
UPRIGHT,MEDIUM,41040,
1B
28 31 39 48 1B 26 74 33
FONT.
: 50048,100, PC891,PROP,
UPRIGHT,MEDIUM,41040,
1B
28 31 39 48 1B 26 74 33
FONT.
: 50049,100, PC891,PROP,
UPRIGHT,MEDIUM,41040,
1B
28 31 39 48 1B 26 74 33
FONT.
: 50050,100, PC891,PROP,
UPRIGHT,MEDIUM,41040,
1B
28 31 39 48 1B 26 74 33
FONT.
: 50051,100, PC891,PROP,
UPRIGHT,MEDIUM,41040,
1B
28 31 39 48 1B 26 74 33
FONT.
: 50052,100, PC891,PROP,
UPRIGHT,MEDIUM,41040,
1B
28 31 39 48 1B 26 74 33
FONT.
: 50053,100, PC891,PROP,
UPRIGHT,MEDIUM,41040,
1B
28 31 39 48 1B 26 74 33
AXIS 5570e / AXIS 5670e User’s Manual
0,
96,
38 50
0,
96,
38 50
0,
80,
38 50
0,
101,
38 50
0,
101,
38 50
0,
84,
38 50
0,
76,
38 50
0,
67,
38 50
0,
67,
38 50
0,
56,
38 50
0,
144,
38 50
0,
120,
38 50
0,
108,
38 50
0,
96,
38 50
0,
80,
38 50
0,
101,
38 50
0,
84,
38 50
0,
76,
38 50
0,
67,
38 50
0,
56,
38 50
241
The Parameter List
FONT.
: 50060,100, PC904,PROP,
UPRIGHT,MEDIUM,0,
FONT.
: 50061,100, PC904,PROP,
UPRIGHT,MEDIUM,0,
FONT.
: 50062,100, PC904,PROP,
UPRIGHT,MEDIUM,0,
FONT.
: 50063,100, PC904,PROP,
UPRIGHT,MEDIUM,0,
FONT.
: 50064,100, PC904,PROP,
UPRIGHT,MEDIUM,0,
FONT.
: 50065,100, PC904,PROP,
UPRIGHT,MEDIUM,0,
FONT.
: 50066,100, PC904,PROP,
UPRIGHT,MEDIUM,0,
FONT.
: 50067,100, PC904,PROP,
UPRIGHT,MEDIUM,0,
FONT.
: 50068,100, PC904,PROP,
UPRIGHT,MEDIUM,0,
FONT.
: 50069,100, PC904,PROP,
UPRIGHT,MEDIUM,0,
FONT.
: 50070,100, PC904,PROP,
UPRIGHT,MEDIUM,0,
FONT.
: 50071,100, PC904,PROP,
UPRIGHT,MEDIUM,0,
FONT.
: 50072,100, PC904,PROP,
UPRIGHT,MEDIUM,0,
FONT.
: 50073,100, PC904,PROP,
UPRIGHT,MEDIUM,0,
FONT.
: 50074,100, PC904,PROP,
UPRIGHT,MEDIUM,0,
FONT.
: 50075,100, PC904,PROP,
UPRIGHT,MEDIUM,0,
FONT.
: 50076,100, PC904,PROP,
UPRIGHT,MEDIUM,0,
FONT.
: 50077,100, PC904,PROP,
UPRIGHT,MEDIUM,0,
FONT.
: 50078,100, PC904,PROP,
UPRIGHT,MEDIUM,0,
FONT.
: 50079,100, PC904,PROP,
UPRIGHT,MEDIUM,0,
FONT.
: 50080,100, PC904,PROP,
UPRIGHT,MEDIUM,0,
FONT.
: 50081,100, PC904,PROP,
UPRIGHT,MEDIUM,0,
FONT.
: 50082,100, PC904,PROP,
UPRIGHT,MEDIUM,0,
FONT.
: 50083,100, PC904,PROP,
UPRIGHT,MEDIUM,0,
FONT.
: 50100,100, PC903,PROP,
UPRIGHT,MEDIUM,37058,
1B
28 31 38 43 1B 26 74 33
FONT.
: 50101,100, PC903,PROP,
UPRIGHT,MEDIUM,37058,
1B
28 31 38 43 1B 26 74 33
FONT.
: 50102,100, PC903,PROP,
UPRIGHT,MEDIUM,37058,
1B
28 31 38 43 1B 26 74 33
FONT.
: 50103,100, PC903,PROP,
UPRIGHT,MEDIUM,37058,
1B
28 31 38 43 1B 26 74 33
242
0,
144,
0,
144,
0,
120,
0,
108,
0,
96,
0,
96,
0,
80,
0,
101,
0,
101,
0,
84,
0,
76,
0,
67,
0,
67,
0,
56,
0,
144,
0,
120,
0,
108,
0,
96,
0,
80,
0,
101,
0,
84,
0,
76,
0,
67,
0,
56,
0,
144,
38 50
0,
144,
38 50
0,
120,
38 50
0,
108,
38 50
AXIS 5570e / AXIS 5670e User’s Manual
The Parameter List
FONT.
: 50104,100, PC903,PROP,
UPRIGHT,MEDIUM,37058,
1B
28 31 38 43 1B 26 74 33
FONT.
: 50105,100, PC903,PROP,
UPRIGHT,MEDIUM,37058,
1B
28 31 38 43 1B 26 74 33
FONT.
: 50106,100, PC903,PROP,
UPRIGHT,MEDIUM,37058,
1B
28 31 38 43 1B 26 74 33
FONT.
: 50107,100, PC903,PROP,
UPRIGHT,MEDIUM,37058,
1B
28 31 38 43 1B 26 74 33
FONT.
: 50108,100, PC903,PROP,
UPRIGHT,MEDIUM,37058,
1B
28 31 38 43 1B 26 74 33
FONT.
: 50109,100, PC903,PROP,
UPRIGHT,MEDIUM,37058,
1B
28 31 38 43 1B 26 74 33
FONT.
: 50110,100, PC903,PROP,
UPRIGHT,MEDIUM,37058,
1B
28 31 38 43 1B 26 74 33
FONT.
: 50111,100, PC903,PROP,
UPRIGHT,MEDIUM,37058,
1B
28 31 38 43 1B 26 74 33
FONT.
: 50112,100, PC903,PROP,
UPRIGHT,MEDIUM,37058,
1B
28 31 38 43 1B 26 74 33
FONT.
: 50113,100, PC903,PROP,
UPRIGHT,MEDIUM,37058,
1B
28 31 38 43 1B 26 74 33
FONT.
: 50114,100, PC903,PROP,
UPRIGHT,MEDIUM,37058,
1B
28 31 38 43 1B 26 74 33
FONT.
: 50115,100, PC903,PROP,
UPRIGHT,MEDIUM,37058,
1B
28 31 38 43 1B 26 74 33
FONT.
: 50116,100, PC903,PROP,
UPRIGHT,MEDIUM,37058,
1B
28 31 38 43 1B 26 74 33
FONT.
: 50117,100, PC903,PROP,
UPRIGHT,MEDIUM,37058,
1B
28 31 38 43 1B 26 74 33
FONT.
: 50118,100, PC903,PROP,
UPRIGHT,MEDIUM,37058,
1B
28 31 38 43 1B 26 74 33
FONT.
: 50119,100, PC903,PROP,
UPRIGHT,MEDIUM,37058,
1B
28 31 38 43 1B 26 74 33
FONT.
: 50120,100, PC903,PROP,
UPRIGHT,MEDIUM,37058,
1B
28 31 38 43 1B 26 74 33
FONT.
: 50121,100, PC903,PROP,
UPRIGHT,MEDIUM,37058,
1B
28 31 38 43 1B 26 74 33
FONT.
: 50122,100, PC903,PROP,
UPRIGHT,MEDIUM,37058,
1B
28 31 38 43 1B 26 74 33
FONT.
: 50123,100, PC903,PROP,
UPRIGHT,MEDIUM,37058,
1B
28 31 38 43 1B 26 74 33
AXIS 5570e / AXIS 5670e User’s Manual
0,
96,
38 50
0,
96,
38 50
0,
80,
38 50
0,
101,
38 50
0,
101,
38 50
0,
84,
38 50
0,
76,
38 50
0,
67,
38 50
0,
67,
38 50
0,
56,
38 50
0,
144,
38 50
0,
120,
38 50
0,
108,
38 50
0,
96,
38 50
0,
80,
38 50
0,
101,
38 50
0,
84,
38 50
0,
76,
38 50
0,
67,
38 50
0,
56,
38 50
243
The Parameter List
FONT.
: 50130,100, PC891,PROP,
UPRIGHT,MEDIUM,43088,
1B
28 31 38 48 1B 26 74 33
FONT.
: 50131,100, PC891,PROP,
UPRIGHT,MEDIUM,43088,
1B
28 31 38 48 1B 26 74 33
FONT.
: 50132,100, PC891,PROP,
UPRIGHT,MEDIUM,43088,
1B
28 31 38 48 1B 26 74 33
FONT.
: 50133,100, PC891,PROP,
UPRIGHT,MEDIUM,43088,
1B
28 31 38 48 1B 26 74 33
FONT.
: 50134,100, PC891,PROP,
UPRIGHT,MEDIUM,43088,
1B
28 31 38 48 1B 26 74 33
FONT.
: 50135,100, PC891,PROP,
UPRIGHT,MEDIUM,43088,
1B
28 31 38 48 1B 26 74 33
FONT.
: 50136,100, PC891,PROP,
UPRIGHT,MEDIUM,43088,
1B
28 31 38 48 1B 26 74 33
FONT.
: 50137,100, PC891,PROP,
UPRIGHT,MEDIUM,43088,
1B
28 31 38 48 1B 26 74 33
FONT.
: 50138,100, PC891,PROP,
UPRIGHT,MEDIUM,43088,
1B
28 31 38 48 1B 26 74 33
FONT.
: 50139,100, PC891,PROP,
UPRIGHT,MEDIUM,43088,
1B
28 31 38 48 1B 26 74 33
FONT.
: 50140,100, PC891,PROP,
UPRIGHT,MEDIUM,43088,
1B
28 31 38 48 1B 26 74 33
FONT.
: 50141,100, PC891,PROP,
UPRIGHT,MEDIUM,43088,
1B
28 31 38 48 1B 26 74 33
FONT.
: 50142,100, PC891,PROP,
UPRIGHT,MEDIUM,43088,
1B
28 31 38 48 1B 26 74 33
FONT.
: 50143,100, PC891,PROP,
UPRIGHT,MEDIUM,43088,
1B
28 31 38 48 1B 26 74 33
FONT.
: 50144,100, PC891,PROP,
UPRIGHT,MEDIUM,41040,
1B
28 31 38 48 1B 26 74 33
FONT.
: 50145,100, PC891,PROP,
UPRIGHT,MEDIUM,41040,
1B
28 31 38 48 1B 26 74 33
FONT.
: 50146,100, PC891,PROP,
UPRIGHT,MEDIUM,41040,
1B
28 31 38 48 1B 26 74 33
FONT.
: 50147,100, PC891,PROP,
UPRIGHT,MEDIUM,41040,
1B
28 31 38 48 1B 26 74 33
FONT.
: 50148,100, PC891,PROP,
UPRIGHT,MEDIUM,41040,
1B
28 31 38 48 1B 26 74 33
FONT.
: 50149,100, PC891,PROP,
UPRIGHT,MEDIUM,41040,
1B
28 31 38 48 1B 26 74 33
244
0,
144,
38 50
0,
144,
38 50
0,
120,
38 50
0,
108,
38 50
0,
96,
38 50
0,
96,
38 50
0,
80,
38 50
0,
101,
38 50
0,
101,
38 50
0,
84,
38 50
0,
76,
38 50
0,
67,
38 50
0,
67,
38 50
0,
56,
38 50
0,
144,
38 50
0,
120,
38 50
0,
108,
38 50
0,
96,
38 50
0,
80,
38 50
0,
101,
38 50
AXIS 5570e / AXIS 5670e User’s Manual
The Parameter List
FONT.
: 50150,100, PC891,PROP,
UPRIGHT,MEDIUM,41040,
1B
28 31 38 48 1B 26 74 33
FONT.
: 50151,100, PC891,PROP,
UPRIGHT,MEDIUM,41040,
1B
28 31 38 48 1B 26 74 33
FONT.
: 50152,100, PC891,PROP,
UPRIGHT,MEDIUM,41040,
1B
28 31 38 48 1B 26 74 33
FONT.
: 50153,100, PC891,PROP,
UPRIGHT,MEDIUM,41040,
1B
28 31 38 48 1B 26 74 33
0,
84,
38 50
0,
76,
38 50
0,
67,
38 50
0,
56,
38 50
--- Email Menu
EMAIL_NOTIFICATION. : NO
REPLY_ADDRESS. :
PAPER_JAM_ADDRESS. :
OUT_OF_PAPER_ADDRESS. :
TONER_LOW_ADDRESS. :
NO_TONER_ADDRESS. :
PRINTER_OFFLINE_ADDRESS. :
AXIS 5570e / AXIS 5670e User’s Manual
245
The Parameter List
AXIS 5670e
(AXIS 5670e Network Print Server V7.00 Oct 04 2004. S/N:
00408C639C36)
Parameter settings:
--- General Menu
NODE_ADDR.
: 00 40 8C 63 9C 36
NETWORK_SPEED. : AUTO_SENSE (AUTO_SENSE, 10_HALF_DX,
10_FULL_DX, 100_HALF_DX, 100_FULL_DX)
PS_NAME.
: AXIS639C36
ROOT_PWD.
: pass
SWUP_KEY.
:
USERS.
:
BASE_URL.
: www.axis.com
CHARSET.
: ISO-8859-1 (ISO-8859-1, UTF-8)
AXIS_PRINT_SYSTEM. : YES
RCONFIG_ENB. : YES
DEF_OUT.
: PR1 (PR1, PR2, PR3, PR4, PR5, PR6, PR7, PR8,
LPT1, COM1, LPT2)
SYS_LOC.
:
SYS_CONT.
:
--- SNA Menu
SNA_ENB.
DEVICE_EMUL.
SNA_FR_TYPE.
NODE_ID.
NODE_SAP.
NWORK_NAME.
LU_NAME.
H1_SAP.
H1_ADDR.
H1_NW_NAME.
H1_MOD_NAME.
H1_LU_NAME.
SNA_LU1.
SNA_LU2.
SNA_LU3.
SNA_LU4.
SNA_LU5.
SNA_LU6.
SNA_LU7.
SNA_LU8.
AUTODIAL.
DIALTIME.
JOB_TIME.
IR_TIME.
SNA_HEXDUMP.
PR8)
:
:
:
:
:
:
:
:
:
:
:
:
:
:
:
:
:
:
:
:
:
:
:
:
:
YES
3174 (3174, 5494)
FR_802_2 (FR_AUTO, FR_802_2, FR_DIX)
E0 73 9C 36
$4
APPN
A63C936C
$4
FF FF FF FF FF FF
APPN
QRMTWSC
DEFAULT
NONE, 1
NONE, 2
NONE, 3
NONE, 4
NONE, 5
NONE, 6
NONE, 7
NONE, 8
NO
20
10
0
NONE (NONE, PR1, PR2, PR3, PR4, PR5, PR6, PR7,
--- LLC Menu
LLC_RESPONSE. : 1300
LLC_REC_ACK. : 20
LLC_INACTIVITY. : 15
--- TN3270E
TN3270E_IR. : 0
TN3270E_COMP. : NO
TN3270E_1.
: OFF, 0 0 0 0, 23, PR1, 1, AXPR1
TN3270E_2.
: OFF, 0 0 0 0, 23, PR2, 2, AXPR2
TN3270E_3.
: OFF, 0 0 0 0, 23, PR3, 3, AXPR3
246
AXIS 5570e / AXIS 5670e User’s Manual
The Parameter List
TN3270E_4.
TN3270E_5.
TN3270E_6.
TN3270E_7.
TN3270E_8.
:
:
:
:
:
OFF,
OFF,
OFF,
OFF,
OFF,
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0,
0,
0,
0,
0,
23,
23,
23,
23,
23,
PR4,
PR5,
PR6,
PR7,
PR8,
4,
5,
6,
7,
8,
AXPR4
AXPR5
AXPR6
AXPR7
AXPR8
--- TN5250E
TN5250E_KA.
TN5250E_1.
TN5250E_2.
TN5250E_3.
TN5250E_4.
TN5250E_5.
TN5250E_6.
TN5250E_7.
TN5250E_8.
:
:
:
:
:
:
:
:
:
YES
OFF,
OFF,
OFF,
OFF,
OFF,
OFF,
OFF,
OFF,
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0,
0,
0,
0,
0,
0,
0,
0,
23,
23,
23,
23,
23,
23,
23,
23,
PR1,
PR2,
PR3,
PR4,
PR5,
PR6,
PR7,
PR8,
1,
2,
3,
4,
5,
6,
7,
8,
AXPR1,
AXPR2,
AXPR3,
AXPR4,
AXPR5,
AXPR6,
AXPR7,
AXPR8,
--- TCP/IP Network Menu
INT_ADDR.
: 10 91 2 40
DEF_ROUT.
: 10 91 0 1
NET_MASK.
: 255 255 0 0
HTTPS_ENB.
: NO
DHCP_ENB.
: YES
AUTOIP_ENB. : YES
BOOTP_ENB.
: YES
RARP_ENB.
: YES
WINS_ENB.
: YES
WINS_ADDR1. : 10 0 5 50
WINS_ADDR2. : 0 0 0 0
NBT_SCOPE_ID. :
DNS_ENB.
: YES
DNS_ADDR1.
: 193 13 178 7
DNS_ADDR2.
: 193 13 178 2
DOMAIN_NAME. : se.axis.com
SLP_ENB.
: YES
SLP_SCOPE_LIST. : DEFAULT
RENDEZVOUS_ENB. : YES
RENDEZVOUS_SRVNAME_LPT1. :
RENDEZVOUS_SRVNAME_COM1. :
RENDEZVOUS_SRVNAME_LPT2. :
SMTP_SERVER. :
FTP_ENB.
: YES
TELNET_ENB. : YES
DEF_IP_FRAME_TYPE. : EthernetII
QSYSOPR,
QSYSOPR,
QSYSOPR,
QSYSOPR,
QSYSOPR,
QSYSOPR,
QSYSOPR,
QSYSOPR,
QSYS
QSYS
QSYS
QSYS
QSYS
QSYS
QSYS
QSYS
(EthernetII, SNAP)
--- TCP/IP Printing Menu
TCP_ENB.
: YES
PAR_TCP_RESTRICT_LIST. :
PROS_PWD.
: netprinter
PROS_PRT.
: 35
LPD_BANN.
: OFF (OFF, AUTO, LAST)
DEFAULT_RAW_TCP. : 9100-9102 (9100-9102, CLOSED)
RTN_OPT.
: NO
PPR_PRSTAT. : NO
RTN_PR1.
: 5001, IPDS, 1
RTN_PR2.
: 0, ASCII, 2
RTN_PR3.
: 0, ASCII, 3
RTN_PR4.
: 5011, SCS, 4
RTN_PR5.
: 5012, SCS, 5
RTN_PR6.
: 5013, SCS, 6
RTN_PR7.
: 0, ASCII, 7
AXIS 5570e / AXIS 5670e User’s Manual
247
The Parameter List
RTN_PR8.
: 0, ASCII, 8
--- SNMP Menu
SNMP_V1_ENB. :
SNMP_V2_ENB. :
READ_COM.
:
WRT_COM.
:
TRAPADDR.
:
TRAP_COM.
:
SYS_NAME.
:
SNMP_AUT.
:
TRAP_PRT.
:
YES
YES
public
pass
0 0 0 0
public
DISABLE
DISABLE
(DISABLE, ENABLE)
(DISABLE, ENABLE)
--- SNMPv3 Menu
SNMP_V3_ENB. : NO
--- NetWare Menu
NETW_ENB.
: YES
NETW_TRANSPORT_PROTOCOL. : DUAL_STACK (IPX_ONLY, IP_ONLY,
DUAL_STACK)
NDPS.
: TCP_AND_SPX (TCP_AND_SPX, TCP_ONLY, SPX_ONLY,
DISABLED)
JOB_CHECK_DELAY. : 5
CONF_CHECK_DELAY. : 300
FR_802_3.
: YES
FR_ETH_2.
: YES
FR_802_2.
: YES
FR_SNAP.
: YES
NCP_BURST_MODE. : YES
PSERVER_NDS_TREE. :
PSERVER_NDS_FILESERVER. :
PSERVER_NDS_DISTINGUISHED_NAME. :
PSERVER_BINDERY1. :
PSERVER_BINDERY2. :
PSERVER_BINDERY3. :
PSERVER_BINDERY4. :
PSERVER_BINDERY5. :
PSERVER_BINDERY6. :
PSERVER_BINDERY7. :
PSERVER_BINDERY8. :
PSERVER_BINDERY9. :
PSERVER_BINDERY10. :
PSERVER_BINDERY11. :
PSERVER_BINDERY12. :
PSERVER_BINDERY13. :
PSERVER_BINDERY14. :
PSERVER_BINDERY15. :
PSERVER_BINDERY16. :
NPRINTER1.
:
NPRINTER2.
:
NPRINTER3.
:
NPRINTER4.
:
NPRINTER5.
:
NPRINTER6.
:
NPRINTER7.
:
NPRINTER8.
:
--- NetBIOS/NetBEUI Menu
LSLM_ENB.
: YES
NB_FR_TYPE. : FR_802_2 (FR_AUTO, FR_802_2, FR_DIX)
LPRINT_1.
: AX639C36.LP1
248
AXIS 5570e / AXIS 5670e User’s Manual
The Parameter List
LLOGIC_1.
LPT1, COM1,
LPRINT_2.
LLOGIC_2.
LPT1, COM1,
LPRINT_3.
LLOGIC_3.
LPT1, COM1,
LPRINT_4.
LLOGIC_4.
LPT1, COM1,
LPRINT_5.
LLOGIC_5.
LPT1, COM1,
LPRINT_6.
LLOGIC_6.
LPT1, COM1,
LPRINT_7.
LLOGIC_7.
LPT1, COM1,
LPRINT_8.
LLOGIC_8.
LPT1, COM1,
: PR1 (PR1, PR2,
LPT2)
: AX639C36.LP2
: PR2 (PR1, PR2,
LPT2)
: AX639C36.CM1
: PR3 (PR1, PR2,
LPT2)
:
: PR4 (PR1, PR2,
LPT2)
:
: PR5 (PR1, PR2,
LPT2)
:
: PR6 (PR1, PR2,
LPT2)
:
: PR7 (PR1, PR2,
LPT2)
:
: PR8 (PR1, PR2,
LPT2)
PR3, PR4, PR5, PR6, PR7, PR8,
PR3, PR4, PR5, PR6, PR7, PR8,
PR3, PR4, PR5, PR6, PR7, PR8,
PR3, PR4, PR5, PR6, PR7, PR8,
PR3, PR4, PR5, PR6, PR7, PR8,
PR3, PR4, PR5, PR6, PR7, PR8,
PR3, PR4, PR5, PR6, PR7, PR8,
PR3, PR4, PR5, PR6, PR7, PR8,
--- AppleTalk Menu
ATLK_ENB.
: YES
ATK_ZONE.
:
ZONER_EN.
: YES
ATK_FONT.
: DEFAULT (DEFAULT, 35N, ALL)
AUTO_DT_PRIN1. : YES
APRINT_1.
: AXIS639C36_LPT1
ATYPE_1.
: LaserWriter
ALOGIC_1.
: PR1 (PR1, PR2, PR3, PR4, PR5, PR6, PR7, PR8,
LPT1, COM1, LPT2)
BINARY_TYPE_1. : TBCP (TBCP, BCP, NONE)
AUTO_DT_PRIN2. : YES
APRINT_2.
: AXIS639C36_LPT2
ATYPE_2.
: LaserWriter
ALOGIC_2.
: PR2 (PR1, PR2, PR3, PR4, PR5, PR6, PR7, PR8,
LPT1, COM1, LPT2)
BINARY_TYPE_2. : TBCP (TBCP, BCP, NONE)
AUTO_DT_PRIN3. : YES
APRINT_3.
: AXIS639C36_COM1
ATYPE_3.
: LaserWriter
ALOGIC_3.
: PR3 (PR1, PR2, PR3, PR4, PR5, PR6, PR7, PR8,
LPT1, COM1, LPT2)
BINARY_TYPE_3. : TBCP (TBCP, BCP, NONE)
--- Printer1 Menu
PR1_OUT.
: LPT1 (NONE, LPT1, COM1, LPT2)
PR1_NAME.
:
PR1_SCND.
: PR1 (PR1, PR2, PR3, PR4, PR5, PR6, PR7, PR8)
PR1_WAIT.
: YES
PR1_IN.
: AUTO (AUTO, NONE, COM1)
PR1_BEF.
:
PR1_STR.
:
PR1_CSET.
: NONE (NONE, ISO>IBM, 7UK>IBM, 7SW>IBM, 7GE>IBM,
7FR>IBM, 7ND>IBM, DEC>IBM)
PR1_FILT.
: NONE (NONE, POSTSCR, AUTO_PS)
PR1_AFT.
:
PR1_DUMP.
: NO
AXIS 5570e / AXIS 5670e User’s Manual
249
The Parameter List
PR1_SIZE.
: A4 (A4, LETTER, LEGAL, EXECUT)
PR1_ORNT.
: PORTR (PORTR, LANDS, R_PORTR, R_LANDS)
PR1_FORM.
: 66 0 100 60 30 50
PR1_FONT.
:
PR1_DC_MOD. : NONE (NONE, Canon_GP335, Canon_GP605,
Canon_IR3300, Gestetner_3235, Gestetner_3245, Gestetner_3255,
Gestetner_3265, Gestetner_P7032, HP_LaserJet_5Si,
Konica_Minolta_Di250, Konica_Minolta_Di350,
Konica_Minolta_Di520, Konica_Minolta_Di620,
Konica_Minolta_Pi3502, Konica_Minolta_Pi3505e,
Konica_Minolta_Pi4700e, Konica_Minolta_Pi5500,
Konica_Minolta_Pi5501, Konica_Minolta_Pi6500e,
Konica_Minolta_Pi7200e, Konica_Minolta_Pi7500,
Konica_Minolta_CF2001, Ricoh_Aficio_220, Ricoh_Aficio_270,
Ricoh_Aficio_350, Ricoh_Aficio_450, Ricoh_Aficio_550,
Ricoh_Aficio_650, Ricoh_Aficio_AP4500, Ricoh_Aficio_AP3200,
Savin_9935DP, Savin_9945DP, Savin_9955DP, Savin_9965DP,
Sharp_AR286_FN1, Sharp_AR336_FN1, Sharp_AR405_FN1,
Sharp_AR505_FN1, Sharp_AR286_FN2, Sharp_AR336_FN2,
Sharp_AR405_FN2, Sharp_AR505_FN2, Toshiba_DP_4580,
Toshiba_DP_5570, Toshiba_DP_6570, Toshiba_DP_8070,
Toshiba_eSTUDIO35, Toshiba_eSTUDIO45, Toshiba_eSTUDIO55,
Toshiba_eSTUDIO65, Toshiba_eSTUDIO80)
PR1_DC_DUP. : OFF (OFF, SIMPLEX, LONG_EDGE_BINDING,
SHORT_EDGE_BINDING)
PR1_DC_STAP. : OFF (OFF, TOP_LEFT_SLANT, TOP_LEFT_HORIZONTAL,
TOP_LEFT_VERTICAL, TOP_RIGHT, BOTTOM_LEFT, BOTTOM_RIGHT,
TOP_DOUBLE, LEFT_DOUBLE, CENTER)
PR1_DC_HOLE. : OFF (OFF, LONG_EDGE, SHORT_EDGE)
PR1_DC_FOLD. : OFF (OFF, HALF_FOLD, Z_FOLD)
PR1_DC_TRAY. : DEFAULT (DEFAULT, 1, 2, 3, 4, 5)
PR1_DC_COP. : 1
--- Printer2 Menu
PR2_OUT.
: LPT2 (NONE, LPT1, COM1, LPT2)
PR2_NAME.
:
PR2_SCND.
: PR2 (PR1, PR2, PR3, PR4, PR5, PR6, PR7, PR8)
PR2_WAIT.
: YES
PR2_IN.
: AUTO (AUTO, NONE, COM1)
PR2_BEF.
:
PR2_STR.
:
PR2_CSET.
: NONE (NONE, ISO>IBM, 7UK>IBM, 7SW>IBM, 7GE>IBM,
7FR>IBM, 7ND>IBM, DEC>IBM)
PR2_FILT.
: NONE (NONE, POSTSCR, AUTO_PS)
PR2_AFT.
:
PR2_DUMP.
: NO
PR2_SIZE.
: A4 (A4, LETTER, LEGAL, EXECUT)
PR2_ORNT.
: PORTR (PORTR, LANDS, R_PORTR, R_LANDS)
PR2_FORM.
: 66 0 100 60 30 50
PR2_FONT.
:
PR2_DC_MOD. : NONE (NONE, Canon_GP335, Canon_GP605,
Canon_IR3300, Gestetner_3235, Gestetner_3245, Gestetner_3255,
Gestetner_3265, Gestetner_P7032, HP_LaserJet_5Si,
Konica_Minolta_Di250, Konica_Minolta_Di350,
Konica_Minolta_Di520, Konica_Minolta_Di620,
Konica_Minolta_Pi3502, Konica_Minolta_Pi3505e,
Konica_Minolta_Pi4700e, Konica_Minolta_Pi5500,
Konica_Minolta_Pi5501, Konica_Minolta_Pi6500e,
Konica_Minolta_Pi7200e, Konica_Minolta_Pi7500,
Konica_Minolta_CF2001, Ricoh_Aficio_220, Ricoh_Aficio_270,
Ricoh_Aficio_350, Ricoh_Aficio_450, Ricoh_Aficio_550,
250
AXIS 5570e / AXIS 5670e User’s Manual
The Parameter List
Ricoh_Aficio_650, Ricoh_Aficio_AP4500, Ricoh_Aficio_AP3200,
Savin_9935DP, Savin_9945DP, Savin_9955DP, Savin_9965DP,
Sharp_AR286_FN1, Sharp_AR336_FN1, Sharp_AR405_FN1,
Sharp_AR505_FN1, Sharp_AR286_FN2, Sharp_AR336_FN2,
Sharp_AR405_FN2, Sharp_AR505_FN2, Toshiba_DP_4580,
Toshiba_DP_5570, Toshiba_DP_6570, Toshiba_DP_8070,
Toshiba_eSTUDIO35, Toshiba_eSTUDIO45, Toshiba_eSTUDIO55,
Toshiba_eSTUDIO65, Toshiba_eSTUDIO80)
PR2_DC_DUP. : OFF (OFF, SIMPLEX, LONG_EDGE_BINDING,
SHORT_EDGE_BINDING)
PR2_DC_STAP. : OFF (OFF, TOP_LEFT_SLANT, TOP_LEFT_HORIZONTAL,
TOP_LEFT_VERTICAL, TOP_RIGHT, BOTTOM_LEFT, BOTTOM_RIGHT,
TOP_DOUBLE, LEFT_DOUBLE, CENTER)
PR2_DC_HOLE. : OFF (OFF, LONG_EDGE, SHORT_EDGE)
PR2_DC_FOLD. : OFF (OFF, HALF_FOLD, Z_FOLD)
PR2_DC_TRAY. : DEFAULT (DEFAULT, 1, 2, 3, 4, 5)
PR2_DC_COP. : 1
--- Printer3 Menu
PR3_OUT.
: COM1 (NONE, LPT1, COM1, LPT2)
PR3_NAME.
:
PR3_SCND.
: PR3 (PR1, PR2, PR3, PR4, PR5, PR6, PR7, PR8)
PR3_WAIT.
: YES
PR3_IN.
: AUTO (AUTO, NONE, COM1)
PR3_BEF.
:
PR3_STR.
:
PR3_CSET.
: NONE (NONE, ISO>IBM, 7UK>IBM, 7SW>IBM, 7GE>IBM,
7FR>IBM, 7ND>IBM, DEC>IBM)
PR3_FILT.
: NONE (NONE, POSTSCR, AUTO_PS)
PR3_AFT.
:
PR3_DUMP.
: NO
PR3_SIZE.
: A4 (A4, LETTER, LEGAL, EXECUT)
PR3_ORNT.
: PORTR (PORTR, LANDS, R_PORTR, R_LANDS)
PR3_FORM.
: 66 0 100 60 30 50
PR3_FONT.
:
PR3_DC_MOD. : NONE (NONE, Canon_GP335, Canon_GP605,
Canon_IR3300, Gestetner_3235, Gestetner_3245, Gestetner_3255,
Gestetner_3265, Gestetner_P7032, HP_LaserJet_5Si,
Konica_Minolta_Di250, Konica_Minolta_Di350,
Konica_Minolta_Di520, Konica_Minolta_Di620,
Konica_Minolta_Pi3502, Konica_Minolta_Pi3505e,
Konica_Minolta_Pi4700e, Konica_Minolta_Pi5500,
Konica_Minolta_Pi5501, Konica_Minolta_Pi6500e,
Konica_Minolta_Pi7200e, Konica_Minolta_Pi7500,
Konica_Minolta_CF2001, Ricoh_Aficio_220, Ricoh_Aficio_270,
Ricoh_Aficio_350, Ricoh_Aficio_450, Ricoh_Aficio_550,
Ricoh_Aficio_650, Ricoh_Aficio_AP4500, Ricoh_Aficio_AP3200,
Savin_9935DP, Savin_9945DP, Savin_9955DP, Savin_9965DP,
Sharp_AR286_FN1, Sharp_AR336_FN1, Sharp_AR405_FN1,
Sharp_AR505_FN1, Sharp_AR286_FN2, Sharp_AR336_FN2,
Sharp_AR405_FN2, Sharp_AR505_FN2, Toshiba_DP_4580,
Toshiba_DP_5570, Toshiba_DP_6570, Toshiba_DP_8070,
Toshiba_eSTUDIO35, Toshiba_eSTUDIO45, Toshiba_eSTUDIO55,
Toshiba_eSTUDIO65, Toshiba_eSTUDIO80)
PR3_DC_DUP. : OFF (OFF, SIMPLEX, LONG_EDGE_BINDING,
SHORT_EDGE_BINDING)
PR3_DC_STAP. : OFF (OFF, TOP_LEFT_SLANT, TOP_LEFT_HORIZONTAL,
TOP_LEFT_VERTICAL, TOP_RIGHT, BOTTOM_LEFT, BOTTOM_RIGHT,
TOP_DOUBLE, LEFT_DOUBLE, CENTER)
PR3_DC_HOLE. : OFF (OFF, LONG_EDGE, SHORT_EDGE)
PR3_DC_FOLD. : OFF (OFF, HALF_FOLD, Z_FOLD)
AXIS 5570e / AXIS 5670e User’s Manual
251
The Parameter List
PR3_DC_TRAY. : DEFAULT
PR3_DC_COP. : 1
(DEFAULT, 1, 2, 3, 4, 5)
--- Printer4 Menu
PR4_OUT.
: COM1 (NONE, LPT1, COM1, LPT2)
PR4_NAME.
:
PR4_SCND.
: PR4 (PR1, PR2, PR3, PR4, PR5, PR6, PR7, PR8)
PR4_WAIT.
: YES
PR4_IN.
: AUTO (AUTO, NONE, COM1)
PR4_BEF.
:
PR4_STR.
:
PR4_CSET.
: NONE (NONE, ISO>IBM, 7UK>IBM, 7SW>IBM, 7GE>IBM,
7FR>IBM, 7ND>IBM, DEC>IBM)
PR4_FILT.
: NONE (NONE, POSTSCR, AUTO_PS)
PR4_AFT.
:
PR4_DUMP.
: NO
PR4_SIZE.
: A4 (A4, LETTER, LEGAL, EXECUT)
PR4_ORNT.
: PORTR (PORTR, LANDS, R_PORTR, R_LANDS)
PR4_FORM.
: 66 0 100 60 30 50
PR4_FONT.
:
PR4_DC_MOD. : NONE (NONE, Canon_GP335, Canon_GP605,
Canon_IR3300, Gestetner_3235, Gestetner_3245, Gestetner_3255,
Gestetner_3265, Gestetner_P7032, HP_LaserJet_5Si,
Konica_Minolta_Di250, Konica_Minolta_Di350,
Konica_Minolta_Di520, Konica_Minolta_Di620,
Konica_Minolta_Pi3502, Konica_Minolta_Pi3505e,
Konica_Minolta_Pi4700e, Konica_Minolta_Pi5500,
Konica_Minolta_Pi5501, Konica_Minolta_Pi6500e,
Konica_Minolta_Pi7200e, Konica_Minolta_Pi7500,
Konica_Minolta_CF2001, Ricoh_Aficio_220, Ricoh_Aficio_270,
Ricoh_Aficio_350, Ricoh_Aficio_450, Ricoh_Aficio_550,
Ricoh_Aficio_650, Ricoh_Aficio_AP4500, Ricoh_Aficio_AP3200,
Savin_9935DP, Savin_9945DP, Savin_9955DP, Savin_9965DP,
Sharp_AR286_FN1, Sharp_AR336_FN1, Sharp_AR405_FN1,
Sharp_AR505_FN1, Sharp_AR286_FN2, Sharp_AR336_FN2,
Sharp_AR405_FN2, Sharp_AR505_FN2, Toshiba_DP_4580,
Toshiba_DP_5570, Toshiba_DP_6570, Toshiba_DP_8070,
Toshiba_eSTUDIO35, Toshiba_eSTUDIO45, Toshiba_eSTUDIO55,
Toshiba_eSTUDIO65, Toshiba_eSTUDIO80)
PR4_DC_DUP. : OFF (OFF, SIMPLEX, LONG_EDGE_BINDING,
SHORT_EDGE_BINDING)
PR4_DC_STAP. : OFF (OFF, TOP_LEFT_SLANT, TOP_LEFT_HORIZONTAL,
TOP_LEFT_VERTICAL, TOP_RIGHT, BOTTOM_LEFT, BOTTOM_RIGHT,
TOP_DOUBLE, LEFT_DOUBLE, CENTER)
PR4_DC_HOLE. : OFF (OFF, LONG_EDGE, SHORT_EDGE)
PR4_DC_FOLD. : OFF (OFF, HALF_FOLD, Z_FOLD)
PR4_DC_TRAY. : DEFAULT (DEFAULT, 1, 2, 3, 4, 5)
PR4_DC_COP. : 1
--- Printer5 Menu
PR5_OUT.
: LPT1 (NONE, LPT1, COM1, LPT2)
PR5_NAME.
:
PR5_SCND.
: PR5 (PR1, PR2, PR3, PR4, PR5, PR6, PR7, PR8)
PR5_WAIT.
: YES
PR5_IN.
: AUTO (AUTO, NONE, COM1)
PR5_BEF.
:
PR5_STR.
:
PR5_CSET.
: NONE (NONE, ISO>IBM, 7UK>IBM, 7SW>IBM, 7GE>IBM,
7FR>IBM, 7ND>IBM, DEC>IBM)
PR5_FILT.
: NONE (NONE, POSTSCR, AUTO_PS)
PR5_AFT.
:
252
AXIS 5570e / AXIS 5670e User’s Manual
The Parameter List
PR5_DUMP.
: NO
PR5_SIZE.
: A4 (A4, LETTER, LEGAL, EXECUT)
PR5_ORNT.
: PORTR (PORTR, LANDS, R_PORTR, R_LANDS)
PR5_FORM.
: 66 0 100 60 30 50
PR5_FONT.
:
PR5_DC_MOD. : NONE (NONE, Canon_GP335, Canon_GP605,
Canon_IR3300, Gestetner_3235, Gestetner_3245, Gestetner_3255,
Gestetner_3265, Gestetner_P7032, HP_LaserJet_5Si,
Konica_Minolta_Di250, Konica_Minolta_Di350,
Konica_Minolta_Di520, Konica_Minolta_Di620,
Konica_Minolta_Pi3502, Konica_Minolta_Pi3505e,
Konica_Minolta_Pi4700e, Konica_Minolta_Pi5500,
Konica_Minolta_Pi5501, Konica_Minolta_Pi6500e,
Konica_Minolta_Pi7200e, Konica_Minolta_Pi7500,
Konica_Minolta_CF2001, Ricoh_Aficio_220, Ricoh_Aficio_270,
Ricoh_Aficio_350, Ricoh_Aficio_450, Ricoh_Aficio_550,
Ricoh_Aficio_650, Ricoh_Aficio_AP4500, Ricoh_Aficio_AP3200,
Savin_9935DP, Savin_9945DP, Savin_9955DP, Savin_9965DP,
Sharp_AR286_FN1, Sharp_AR336_FN1, Sharp_AR405_FN1,
Sharp_AR505_FN1, Sharp_AR286_FN2, Sharp_AR336_FN2,
Sharp_AR405_FN2, Sharp_AR505_FN2, Toshiba_DP_4580,
Toshiba_DP_5570, Toshiba_DP_6570, Toshiba_DP_8070,
Toshiba_eSTUDIO35, Toshiba_eSTUDIO45, Toshiba_eSTUDIO55,
Toshiba_eSTUDIO65, Toshiba_eSTUDIO80)
PR5_DC_DUP. : OFF (OFF, SIMPLEX, LONG_EDGE_BINDING,
SHORT_EDGE_BINDING)
PR5_DC_STAP. : OFF (OFF, TOP_LEFT_SLANT, TOP_LEFT_HORIZONTAL,
TOP_LEFT_VERTICAL, TOP_RIGHT, BOTTOM_LEFT, BOTTOM_RIGHT,
TOP_DOUBLE, LEFT_DOUBLE, CENTER)
PR5_DC_HOLE. : OFF (OFF, LONG_EDGE, SHORT_EDGE)
PR5_DC_FOLD. : OFF (OFF, HALF_FOLD, Z_FOLD)
PR5_DC_TRAY. : DEFAULT (DEFAULT, 1, 2, 3, 4, 5)
PR5_DC_COP. : 1
--- Printer6 Menu
PR6_OUT.
: LPT2 (NONE, LPT1, COM1, LPT2)
PR6_NAME.
:
PR6_SCND.
: PR6 (PR1, PR2, PR3, PR4, PR5, PR6, PR7, PR8)
PR6_WAIT.
: YES
PR6_IN.
: AUTO (AUTO, NONE, COM1)
PR6_BEF.
:
PR6_STR.
:
PR6_CSET.
: NONE (NONE, ISO>IBM, 7UK>IBM, 7SW>IBM, 7GE>IBM,
7FR>IBM, 7ND>IBM, DEC>IBM)
PR6_FILT.
: NONE (NONE, POSTSCR, AUTO_PS)
PR6_AFT.
:
PR6_DUMP.
: NO
PR6_SIZE.
: A4 (A4, LETTER, LEGAL, EXECUT)
PR6_ORNT.
: PORTR (PORTR, LANDS, R_PORTR, R_LANDS)
PR6_FORM.
: 66 0 100 60 30 50
PR6_FONT.
:
PR6_DC_MOD. : NONE (NONE, Canon_GP335, Canon_GP605,
Canon_IR3300, Gestetner_3235, Gestetner_3245, Gestetner_3255,
Gestetner_3265, Gestetner_P7032, HP_LaserJet_5Si,
Konica_Minolta_Di250, Konica_Minolta_Di350,
Konica_Minolta_Di520, Konica_Minolta_Di620,
Konica_Minolta_Pi3502, Konica_Minolta_Pi3505e,
Konica_Minolta_Pi4700e, Konica_Minolta_Pi5500,
Konica_Minolta_Pi5501, Konica_Minolta_Pi6500e,
Konica_Minolta_Pi7200e, Konica_Minolta_Pi7500,
Konica_Minolta_CF2001, Ricoh_Aficio_220, Ricoh_Aficio_270,
AXIS 5570e / AXIS 5670e User’s Manual
253
The Parameter List
Ricoh_Aficio_350, Ricoh_Aficio_450, Ricoh_Aficio_550,
Ricoh_Aficio_650, Ricoh_Aficio_AP4500, Ricoh_Aficio_AP3200,
Savin_9935DP, Savin_9945DP, Savin_9955DP, Savin_9965DP,
Sharp_AR286_FN1, Sharp_AR336_FN1, Sharp_AR405_FN1,
Sharp_AR505_FN1, Sharp_AR286_FN2, Sharp_AR336_FN2,
Sharp_AR405_FN2, Sharp_AR505_FN2, Toshiba_DP_4580,
Toshiba_DP_5570, Toshiba_DP_6570, Toshiba_DP_8070,
Toshiba_eSTUDIO35, Toshiba_eSTUDIO45, Toshiba_eSTUDIO55,
Toshiba_eSTUDIO65, Toshiba_eSTUDIO80)
PR6_DC_DUP. : OFF (OFF, SIMPLEX, LONG_EDGE_BINDING,
SHORT_EDGE_BINDING)
PR6_DC_STAP. : OFF (OFF, TOP_LEFT_SLANT, TOP_LEFT_HORIZONTAL,
TOP_LEFT_VERTICAL, TOP_RIGHT, BOTTOM_LEFT, BOTTOM_RIGHT,
TOP_DOUBLE, LEFT_DOUBLE, CENTER)
PR6_DC_HOLE. : OFF (OFF, LONG_EDGE, SHORT_EDGE)
PR6_DC_FOLD. : OFF (OFF, HALF_FOLD, Z_FOLD)
PR6_DC_TRAY. : DEFAULT (DEFAULT, 1, 2, 3, 4, 5)
PR6_DC_COP. : 1
--- Printer7 Menu
PR7_OUT.
: COM1 (NONE, LPT1, COM1, LPT2)
PR7_NAME.
:
PR7_SCND.
: PR7 (PR1, PR2, PR3, PR4, PR5, PR6, PR7, PR8)
PR7_WAIT.
: YES
PR7_IN.
: AUTO (AUTO, NONE, COM1)
PR7_BEF.
:
PR7_STR.
:
PR7_CSET.
: NONE (NONE, ISO>IBM, 7UK>IBM, 7SW>IBM, 7GE>IBM,
7FR>IBM, 7ND>IBM, DEC>IBM)
PR7_FILT.
: NONE (NONE, POSTSCR, AUTO_PS)
PR7_AFT.
:
PR7_DUMP.
: NO
PR7_SIZE.
: A4 (A4, LETTER, LEGAL, EXECUT)
PR7_ORNT.
: PORTR (PORTR, LANDS, R_PORTR, R_LANDS)
PR7_FORM.
: 66 0 100 60 30 50
PR7_FONT.
:
PR7_DC_MOD. : NONE (NONE, Canon_GP335, Canon_GP605,
Canon_IR3300, Gestetner_3235, Gestetner_3245, Gestetner_3255,
Gestetner_3265, Gestetner_P7032, HP_LaserJet_5Si,
Konica_Minolta_Di250, Konica_Minolta_Di350,
Konica_Minolta_Di520, Konica_Minolta_Di620,
Konica_Minolta_Pi3502, Konica_Minolta_Pi3505e,
Konica_Minolta_Pi4700e, Konica_Minolta_Pi5500,
Konica_Minolta_Pi5501, Konica_Minolta_Pi6500e,
Konica_Minolta_Pi7200e, Konica_Minolta_Pi7500,
Konica_Minolta_CF2001, Ricoh_Aficio_220, Ricoh_Aficio_270,
Ricoh_Aficio_350, Ricoh_Aficio_450, Ricoh_Aficio_550,
Ricoh_Aficio_650, Ricoh_Aficio_AP4500, Ricoh_Aficio_AP3200,
Savin_9935DP, Savin_9945DP, Savin_9955DP, Savin_9965DP,
Sharp_AR286_FN1, Sharp_AR336_FN1, Sharp_AR405_FN1,
Sharp_AR505_FN1, Sharp_AR286_FN2, Sharp_AR336_FN2,
Sharp_AR405_FN2, Sharp_AR505_FN2, Toshiba_DP_4580,
Toshiba_DP_5570, Toshiba_DP_6570, Toshiba_DP_8070,
Toshiba_eSTUDIO35, Toshiba_eSTUDIO45, Toshiba_eSTUDIO55,
Toshiba_eSTUDIO65, Toshiba_eSTUDIO80)
PR7_DC_DUP. : OFF (OFF, SIMPLEX, LONG_EDGE_BINDING,
SHORT_EDGE_BINDING)
PR7_DC_STAP. : OFF (OFF, TOP_LEFT_SLANT, TOP_LEFT_HORIZONTAL,
TOP_LEFT_VERTICAL, TOP_RIGHT, BOTTOM_LEFT, BOTTOM_RIGHT,
TOP_DOUBLE, LEFT_DOUBLE, CENTER)
PR7_DC_HOLE. : OFF (OFF, LONG_EDGE, SHORT_EDGE)
254
AXIS 5570e / AXIS 5670e User’s Manual
The Parameter List
PR7_DC_FOLD. : OFF (OFF, HALF_FOLD, Z_FOLD)
PR7_DC_TRAY. : DEFAULT (DEFAULT, 1, 2, 3, 4, 5)
PR7_DC_COP. : 1
--- Printer8 Menu
PR8_OUT.
: COM1 (NONE, LPT1, COM1, LPT2)
PR8_NAME.
:
PR8_SCND.
: PR8 (PR1, PR2, PR3, PR4, PR5, PR6, PR7, PR8)
PR8_WAIT.
: YES
PR8_IN.
: AUTO (AUTO, NONE, COM1)
PR8_BEF.
:
PR8_STR.
:
PR8_CSET.
: NONE (NONE, ISO>IBM, 7UK>IBM, 7SW>IBM, 7GE>IBM,
7FR>IBM, 7ND>IBM, DEC>IBM)
PR8_FILT.
: NONE (NONE, POSTSCR, AUTO_PS)
PR8_AFT.
:
PR8_DUMP.
: NO
PR8_SIZE.
: A4 (A4, LETTER, LEGAL, EXECUT)
PR8_ORNT.
: PORTR (PORTR, LANDS, R_PORTR, R_LANDS)
PR8_FORM.
: 66 0 100 60 30 50
PR8_FONT.
:
PR8_DC_MOD. : NONE (NONE, Canon_GP335, Canon_GP605,
Canon_IR3300, Gestetner_3235, Gestetner_3245, Gestetner_3255,
Gestetner_3265, Gestetner_P7032, HP_LaserJet_5Si,
Konica_Minolta_Di250, Konica_Minolta_Di350,
Konica_Minolta_Di520, Konica_Minolta_Di620,
Konica_Minolta_Pi3502, Konica_Minolta_Pi3505e,
Konica_Minolta_Pi4700e, Konica_Minolta_Pi5500,
Konica_Minolta_Pi5501, Konica_Minolta_Pi6500e,
Konica_Minolta_Pi7200e, Konica_Minolta_Pi7500,
Konica_Minolta_CF2001, Ricoh_Aficio_220, Ricoh_Aficio_270,
Ricoh_Aficio_350, Ricoh_Aficio_450, Ricoh_Aficio_550,
Ricoh_Aficio_650, Ricoh_Aficio_AP4500, Ricoh_Aficio_AP3200,
Savin_9935DP, Savin_9945DP, Savin_9955DP, Savin_9965DP,
Sharp_AR286_FN1, Sharp_AR336_FN1, Sharp_AR405_FN1,
Sharp_AR505_FN1, Sharp_AR286_FN2, Sharp_AR336_FN2,
Sharp_AR405_FN2, Sharp_AR505_FN2, Toshiba_DP_4580,
Toshiba_DP_5570, Toshiba_DP_6570, Toshiba_DP_8070,
Toshiba_eSTUDIO35, Toshiba_eSTUDIO45, Toshiba_eSTUDIO55,
Toshiba_eSTUDIO65, Toshiba_eSTUDIO80)
PR8_DC_DUP. : OFF (OFF, SIMPLEX, LONG_EDGE_BINDING,
SHORT_EDGE_BINDING)
PR8_DC_STAP. : OFF (OFF, TOP_LEFT_SLANT, TOP_LEFT_HORIZONTAL,
TOP_LEFT_VERTICAL, TOP_RIGHT, BOTTOM_LEFT, BOTTOM_RIGHT,
TOP_DOUBLE, LEFT_DOUBLE, CENTER)
PR8_DC_HOLE. : OFF (OFF, LONG_EDGE, SHORT_EDGE)
PR8_DC_FOLD. : OFF (OFF, HALF_FOLD, Z_FOLD)
PR8_DC_TRAY. : DEFAULT (DEFAULT, 1, 2, 3, 4, 5)
PR8_DC_COP. : 1
--- LPT1 Menu
L1_CENTR.
:
L1_BSYTM.
:
L1_MGM_INFO. :
L1_COMMENT. :
L1_BIDIR.
:
L1_READT.
:
HISPEED (IBM_PC, STNDRD, FAST, HISPEED, HINOACK)
60
AUTO (DISABLE, AUTO)
AUTO
3
(DISABLE, AUTO)
--- COM1 Menu
C1_BAUDR.
: 9600 (300, 600, 1200, 2400, 4800, 9600, 19200,
38400, 57600, 115200)
AXIS 5570e / AXIS 5670e User’s Manual
255
The Parameter List
C1_NBITS.
: 8 (7, 8)
C1_PARIT.
: NONE (NONE, ODD, EVEN)
C1_STOPB.
: 2 (1, 2)
C1_HNDSH.
: ROBUST-BOTH (NONE, XON/XOFF, ROBUST, RDY/BSY,
BOTH, ROBUST-BOTH)
C1_READT.
: 3
C1_BSYTM.
: 60
C1_MGM_INFO. : AUTO (DISABLE, AUTO)
C1_COMMENT. :
--- LPT2 Menu
L2_CENTR.
:
L2_BSYTM.
:
L2_MGM_INFO. :
L2_COMMENT. :
L2_BIDIR.
:
L2_READT.
:
HISPEED (IBM_PC, STNDRD, FAST, HISPEED, HINOACK)
60
AUTO (DISABLE, AUTO)
AUTO
3
(DISABLE, AUTO)
--- IBM IPDS Configuration
IPDS_COLSUP. : Disabled
IPDS_DUPSUP. : Enabled
IPDS_OPTDUP. : Enabled
IPDS_RAF.
: Disabled
IPDS_NUP.
: 1-up (1-up, 2-up, 4-up)
IPDS_OVLXOFF. : 0
IPDS_OVLYOFF. : 0
IPDS_RPTXOFF. : 0
IPDS_RPTYOFF. : 0
IPDS_DOB.
: Bin1 (Bin1, Bin2, Bin3, Bin4, Bin5, Bin6)
IPDS_DIB.
: Bin1 (Bin1, Bin2, Bin3, Bin4, Bin5)
PS_IPLINK.
: Off (Off, Sheet, Bin)
IPDS_BIN1.
: Letter, 0, 0
IPDS_BIN2.
: Letter, 0, 0
IPDS_BIN3.
: Letter, 0, 0
IPDS_BIN4.
: Letter, 0, 0
IPDS_BIN5.
: Letter, 0, 0
--- IBM IPDS
PS_LFSM.
PS_ERRH.
PS_OPTOVL.
PS_G4SUP.
PS_VM.
PS_BIN1.
PS_BIN2.
PS_BIN3.
PS_BIN4.
PS_BIN5.
PS_DEST.
PostScript
: Enabled
: Disabled
: Enabled
: Disabled
: 2000
: Default,
: Default,
: Default,
: Default,
: Default,
: 0, 0, 0,
Driver Settings
100, 100,
100, 100,
100, 100,
100, 100,
100, 100,
0, 0, 0
0,
0,
0,
0,
0,
0
0
0
0
0
--- IBM IPDS PCL Driver Settings
PCL_VER.
: 5 (3, 4, 5)
PCL_SBSET.
: AUTOMATIC (AUTOMATIC, US-ASCII, Latin1, Latin5,
Latin9, PC437, PC850, PC852, PC874, Roman8)
PCL_OCR_ENB. : Enabled
PCL_OPTOVL. : Disabled
PCL_BIN1.
: 8, 0, 0
PCL_BIN2.
: 1, 0, 0
PCL_BIN3.
: 4, 0, 0
PCL_BIN4.
: 5, 0, 0
PCL_BIN5.
: 0, 0, 0
256
AXIS 5570e / AXIS 5670e User’s Manual
The Parameter List
PCL_DEST.
: 0, 0, 0, 0, 0, 0
--- IBM EMULATOR 1
IPDS_PREMUL1. : IPDS_4332 (IPDS_4224_C2, IPDS_4224_E3,
IPDS_3812_2, IPDS_3812_2_00, IPDS_3816, IPDS_4028_1,
IPDS_4028_2, IPDS_4312, IPDS_4317, IPDS_4324, IPDS_4332)
IPDS_PRRES1. : 0
IPDS_SYSL1. : 37 (37, 256, 259, 260, 273, 274, 275, 277, 278,
280, 281, 282, 284, 285, 286, 287, 288, 289, 290, 293, 297, 361,
420, 423, 424, 437, 500, 803, 819, 838, 852, 853, 857, 858, 860,
861, 863, 865, 870, 871, 880, 892, 893, 905, 912, 914, 920, 923,
924, 1004, 1026, 1069, 1140, 1141, 1142, 1143, 1144, 1145, 1146,
1147, 1148, 1149, 1252)
IPDS_PD1.
: PostScript (PostScript, PCL)
IPDS_SOJS1. :
IPDS_EOJS1. :
PREMUL1.
: 3816_CX (3287_CX, 3268_CX, 3262_CX, 4214_CX,
4224_CX, 4230_CX, 3812_CX, 3816S_CX, 3816_CX, 5224_TX, 5225_TX,
5256_TX, 4214_TX, 4230_TX, 3812_TX, 3816S_TX, 3816_TX,
5X27_001_TX, 5X27_002_KS_TX, 5X27_002_KSSM_TX, 5X27_003_TX,
5X27_005_TX)
SYSL1.
: 37 (37, 256, 260, 273, 274, 275, 277, 278, 280,
281, 282, 284, 285, 286, 287, 288, 289, 290, 293, 297, 340, 361,
500, 833, 836, 838, 870, 871, 892, 893, 1026, 1140, 1141, 1142,
1143, 1144, 1145, 1146, 1147, 1148, 1149, USER)
PASSTHR1.
: NO
MPL1.
: 66, ENA
MPP1.
: 132, ENA
LPI1.
: 6 (3, 4, 6, 8)
CPI1.
: 10 (5, 10, 12, 13.3, 15, 17, 18)
DCPI1.
: 5.0 (5.0, 6.0, 6.7, 7.5, 9.0)
AUTORI1.
: YES
LM1.
: 0, 0, 48
TM1.
: 26, 26, 74
LDSF1.
: 100, 100, 70
DEFBIN1.
: BIN1 (BIN1, BIN2, BIN3, BIN4, BIN5, BIN6,
MANUAL, ENVELOPE, CONTINUOUS)
PRDRIVER1.
: PCL5 (USER, GENERIC, PCL4, PCL5, IBM_PRO,
EPSON_FX, EPSON_FX_15CPI, EPSON_LQ, EPSON_LQ_8LPI,
EPSON_LQ_1600K, EPSON_LQ_KS)
--- IBM EMULATOR 2
IPDS_PREMUL2. : IPDS_4332 (IPDS_4224_C2, IPDS_4224_E3,
IPDS_3812_2, IPDS_3812_2_00, IPDS_3816, IPDS_4028_1,
IPDS_4028_2, IPDS_4312, IPDS_4317, IPDS_4324, IPDS_4332)
IPDS_PRRES2. : 0
IPDS_SYSL2. : 37 (37, 256, 259, 260, 273, 274, 275, 277, 278,
280, 281, 282, 284, 285, 286, 287, 288, 289, 290, 293, 297, 361,
420, 423, 424, 437, 500, 803, 819, 838, 852, 853, 857, 858, 860,
861, 863, 865, 870, 871, 880, 892, 893, 905, 912, 914, 920, 923,
924, 1004, 1026, 1069, 1140, 1141, 1142, 1143, 1144, 1145, 1146,
1147, 1148, 1149, 1252)
IPDS_PD2.
: PostScript (PostScript, PCL)
IPDS_SOJS2. :
IPDS_EOJS2. :
PREMUL2.
: 3816_CX (3287_CX, 3268_CX, 3262_CX, 4214_CX,
4224_CX, 4230_CX, 3812_CX, 3816S_CX, 3816_CX, 5224_TX, 5225_TX,
5256_TX, 4214_TX, 4230_TX, 3812_TX, 3816S_TX, 3816_TX,
5X27_001_TX, 5X27_002_KS_TX, 5X27_002_KSSM_TX, 5X27_003_TX,
5X27_005_TX)
AXIS 5570e / AXIS 5670e User’s Manual
257
The Parameter List
SYSL2.
: 37 (37, 256, 260, 273, 274, 275, 277, 278, 280,
281, 282, 284, 285, 286, 287, 288, 289, 290, 293, 297, 340, 361,
500, 833, 836, 838, 870, 871, 892, 893, 1026, 1140, 1141, 1142,
1143, 1144, 1145, 1146, 1147, 1148, 1149, USER)
PASSTHR2.
: NO
MPL2.
: 66, ENA
MPP2.
: 132, ENA
LPI2.
: 6 (3, 4, 6, 8)
CPI2.
: 10 (5, 10, 12, 13.3, 15, 17, 18)
DCPI2.
: 5.0 (5.0, 6.0, 6.7, 7.5, 9.0)
AUTORI2.
: YES
LM2.
: 0, 0, 48
TM2.
: 26, 26, 74
LDSF2.
: 100, 100, 70
DEFBIN2.
: BIN1 (BIN1, BIN2, BIN3, BIN4, BIN5, BIN6,
MANUAL, ENVELOPE, CONTINUOUS)
PRDRIVER2.
: PCL5 (USER, GENERIC, PCL4, PCL5, IBM_PRO,
EPSON_FX, EPSON_FX_15CPI, EPSON_LQ, EPSON_LQ_8LPI,
EPSON_LQ_1600K, EPSON_LQ_KS)
--- IBM EMULATOR 3
IPDS_PREMUL3. : IPDS_4332 (IPDS_4224_C2, IPDS_4224_E3,
IPDS_3812_2, IPDS_3812_2_00, IPDS_3816, IPDS_4028_1,
IPDS_4028_2, IPDS_4312, IPDS_4317, IPDS_4324, IPDS_4332)
IPDS_PRRES3. : 0
IPDS_SYSL3. : 37 (37, 256, 259, 260, 273, 274, 275, 277, 278,
280, 281, 282, 284, 285, 286, 287, 288, 289, 290, 293, 297, 361,
420, 423, 424, 437, 500, 803, 819, 838, 852, 853, 857, 858, 860,
861, 863, 865, 870, 871, 880, 892, 893, 905, 912, 914, 920, 923,
924, 1004, 1026, 1069, 1140, 1141, 1142, 1143, 1144, 1145, 1146,
1147, 1148, 1149, 1252)
IPDS_PD3.
: PostScript (PostScript, PCL)
IPDS_SOJS3. :
IPDS_EOJS3. :
PREMUL3.
: 3816_CX (3287_CX, 3268_CX, 3262_CX, 4214_CX,
4224_CX, 4230_CX, 3812_CX, 3816S_CX, 3816_CX, 5224_TX, 5225_TX,
5256_TX, 4214_TX, 4230_TX, 3812_TX, 3816S_TX, 3816_TX,
5X27_001_TX, 5X27_002_KS_TX, 5X27_002_KSSM_TX, 5X27_003_TX,
5X27_005_TX)
SYSL3.
: 37 (37, 256, 260, 273, 274, 275, 277, 278, 280,
281, 282, 284, 285, 286, 287, 288, 289, 290, 293, 297, 340, 361,
500, 833, 836, 838, 870, 871, 892, 893, 1026, 1140, 1141, 1142,
1143, 1144, 1145, 1146, 1147, 1148, 1149, USER)
PASSTHR3.
: NO
MPL3.
: 66, ENA
MPP3.
: 132, ENA
LPI3.
: 6 (3, 4, 6, 8)
CPI3.
: 10 (5, 10, 12, 13.3, 15, 17, 18)
DCPI3.
: 5.0 (5.0, 6.0, 6.7, 7.5, 9.0)
AUTORI3.
: YES
LM3.
: 0, 0, 48
TM3.
: 26, 26, 74
LDSF3.
: 100, 100, 70
DEFBIN3.
: BIN1 (BIN1, BIN2, BIN3, BIN4, BIN5, BIN6,
MANUAL, ENVELOPE, CONTINUOUS)
PRDRIVER3.
: PCL5 (USER, GENERIC, PCL4, PCL5, IBM_PRO,
EPSON_FX, EPSON_FX_15CPI, EPSON_LQ, EPSON_LQ_8LPI,
EPSON_LQ_1600K, EPSON_LQ_KS)
--- IBM EMULATOR 4
258
AXIS 5570e / AXIS 5670e User’s Manual
The Parameter List
IPDS_PREMUL4. : IPDS_4332 (IPDS_4224_C2, IPDS_4224_E3,
IPDS_3812_2, IPDS_3812_2_00, IPDS_3816, IPDS_4028_1,
IPDS_4028_2, IPDS_4312, IPDS_4317, IPDS_4324, IPDS_4332)
IPDS_PRRES4. : 0
IPDS_SYSL4. : 37 (37, 256, 259, 260, 273, 274, 275, 277, 278,
280, 281, 282, 284, 285, 286, 287, 288, 289, 290, 293, 297, 361,
420, 423, 424, 437, 500, 803, 819, 838, 852, 853, 857, 858, 860,
861, 863, 865, 870, 871, 880, 892, 893, 905, 912, 914, 920, 923,
924, 1004, 1026, 1069, 1140, 1141, 1142, 1143, 1144, 1145, 1146,
1147, 1148, 1149, 1252)
IPDS_PD4.
: PostScript (PostScript, PCL)
IPDS_SOJS4. :
IPDS_EOJS4. :
PREMUL4.
: 3816_CX (3287_CX, 3268_CX, 3262_CX, 4214_CX,
4224_CX, 4230_CX, 3812_CX, 3816S_CX, 3816_CX, 5224_TX, 5225_TX,
5256_TX, 4214_TX, 4230_TX, 3812_TX, 3816S_TX, 3816_TX,
5X27_001_TX, 5X27_002_KS_TX, 5X27_002_KSSM_TX, 5X27_003_TX,
5X27_005_TX)
SYSL4.
: 37 (37, 256, 260, 273, 274, 275, 277, 278, 280,
281, 282, 284, 285, 286, 287, 288, 289, 290, 293, 297, 340, 361,
500, 833, 836, 838, 870, 871, 892, 893, 1026, 1140, 1141, 1142,
1143, 1144, 1145, 1146, 1147, 1148, 1149, USER)
PASSTHR4.
: NO
MPL4.
: 66, ENA
MPP4.
: 132, ENA
LPI4.
: 6 (3, 4, 6, 8)
CPI4.
: 10 (5, 10, 12, 13.3, 15, 17, 18)
DCPI4.
: 5.0 (5.0, 6.0, 6.7, 7.5, 9.0)
AUTORI4.
: YES
LM4.
: 0, 0, 48
TM4.
: 26, 26, 74
LDSF4.
: 100, 100, 70
DEFBIN4.
: BIN1 (BIN1, BIN2, BIN3, BIN4, BIN5, BIN6,
MANUAL, ENVELOPE, CONTINUOUS)
PRDRIVER4.
: PCL5 (USER, GENERIC, PCL4, PCL5, IBM_PRO,
EPSON_FX, EPSON_FX_15CPI, EPSON_LQ, EPSON_LQ_8LPI,
EPSON_LQ_1600K, EPSON_LQ_KS)
--- IBM EMULATOR 5
IPDS_PREMUL5. : IPDS_4332 (IPDS_4224_C2, IPDS_4224_E3,
IPDS_3812_2, IPDS_3812_2_00, IPDS_3816, IPDS_4028_1,
IPDS_4028_2, IPDS_4312, IPDS_4317, IPDS_4324, IPDS_4332)
IPDS_PRRES5. : 0
IPDS_SYSL5. : 37 (37, 256, 259, 260, 273, 274, 275, 277, 278,
280, 281, 282, 284, 285, 286, 287, 288, 289, 290, 293, 297, 361,
420, 423, 424, 437, 500, 803, 819, 838, 852, 853, 857, 858, 860,
861, 863, 865, 870, 871, 880, 892, 893, 905, 912, 914, 920, 923,
924, 1004, 1026, 1069, 1140, 1141, 1142, 1143, 1144, 1145, 1146,
1147, 1148, 1149, 1252)
IPDS_PD5.
: PostScript (PostScript, PCL)
IPDS_SOJS5. :
IPDS_EOJS5. :
PREMUL5.
: 3816_CX (3287_CX, 3268_CX, 3262_CX, 4214_CX,
4224_CX, 4230_CX, 3812_CX, 3816S_CX, 3816_CX, 5224_TX, 5225_TX,
5256_TX, 4214_TX, 4230_TX, 3812_TX, 3816S_TX, 3816_TX,
5X27_001_TX, 5X27_002_KS_TX, 5X27_002_KSSM_TX, 5X27_003_TX,
5X27_005_TX)
SYSL5.
: 37 (37, 256, 260, 273, 274, 275, 277, 278, 280,
281, 282, 284, 285, 286, 287, 288, 289, 290, 293, 297, 340, 361,
500, 833, 836, 838, 870, 871, 892, 893, 1026, 1140, 1141, 1142,
1143, 1144, 1145, 1146, 1147, 1148, 1149, USER)
AXIS 5570e / AXIS 5670e User’s Manual
259
The Parameter List
PASSTHR5.
: NO
MPL5.
: 66, ENA
MPP5.
: 132, ENA
LPI5.
: 6 (3, 4, 6, 8)
CPI5.
: 10 (5, 10, 12, 13.3, 15, 17, 18)
DCPI5.
: 5.0 (5.0, 6.0, 6.7, 7.5, 9.0)
AUTORI5.
: YES
LM5.
: 0, 0, 48
TM5.
: 26, 26, 74
LDSF5.
: 100, 100, 70
DEFBIN5.
: BIN1 (BIN1, BIN2, BIN3, BIN4, BIN5, BIN6,
MANUAL, ENVELOPE, CONTINUOUS)
PRDRIVER5.
: PCL5 (USER, GENERIC, PCL4, PCL5, IBM_PRO,
EPSON_FX, EPSON_FX_15CPI, EPSON_LQ, EPSON_LQ_8LPI,
EPSON_LQ_1600K, EPSON_LQ_KS)
--- IBM EMULATOR 6
IPDS_PREMUL6. : IPDS_4332 (IPDS_4224_C2, IPDS_4224_E3,
IPDS_3812_2, IPDS_3812_2_00, IPDS_3816, IPDS_4028_1,
IPDS_4028_2, IPDS_4312, IPDS_4317, IPDS_4324, IPDS_4332)
IPDS_PRRES6. : 0
IPDS_SYSL6. : 37 (37, 256, 259, 260, 273, 274, 275, 277, 278,
280, 281, 282, 284, 285, 286, 287, 288, 289, 290, 293, 297, 361,
420, 423, 424, 437, 500, 803, 819, 838, 852, 853, 857, 858, 860,
861, 863, 865, 870, 871, 880, 892, 893, 905, 912, 914, 920, 923,
924, 1004, 1026, 1069, 1140, 1141, 1142, 1143, 1144, 1145, 1146,
1147, 1148, 1149, 1252)
IPDS_PD6.
: PostScript (PostScript, PCL)
IPDS_SOJS6. :
IPDS_EOJS6. :
PREMUL6.
: 3816_CX (3287_CX, 3268_CX, 3262_CX, 4214_CX,
4224_CX, 4230_CX, 3812_CX, 3816S_CX, 3816_CX, 5224_TX, 5225_TX,
5256_TX, 4214_TX, 4230_TX, 3812_TX, 3816S_TX, 3816_TX,
5X27_001_TX, 5X27_002_KS_TX, 5X27_002_KSSM_TX, 5X27_003_TX,
5X27_005_TX)
SYSL6.
: 37 (37, 256, 260, 273, 274, 275, 277, 278, 280,
281, 282, 284, 285, 286, 287, 288, 289, 290, 293, 297, 340, 361,
500, 833, 836, 838, 870, 871, 892, 893, 1026, 1140, 1141, 1142,
1143, 1144, 1145, 1146, 1147, 1148, 1149, USER)
PASSTHR6.
: NO
MPL6.
: 66, ENA
MPP6.
: 132, ENA
LPI6.
: 6 (3, 4, 6, 8)
CPI6.
: 10 (5, 10, 12, 13.3, 15, 17, 18)
DCPI6.
: 5.0 (5.0, 6.0, 6.7, 7.5, 9.0)
AUTORI6.
: YES
LM6.
: 0, 0, 48
TM6.
: 26, 26, 74
LDSF6.
: 100, 100, 70
DEFBIN6.
: BIN1 (BIN1, BIN2, BIN3, BIN4, BIN5, BIN6,
MANUAL, ENVELOPE, CONTINUOUS)
PRDRIVER6.
: PCL5 (USER, GENERIC, PCL4, PCL5, IBM_PRO,
EPSON_FX, EPSON_FX_15CPI, EPSON_LQ, EPSON_LQ_8LPI,
EPSON_LQ_1600K, EPSON_LQ_KS)
--- IBM EMULATOR 7
IPDS_PREMUL7. : IPDS_4332 (IPDS_4224_C2, IPDS_4224_E3,
IPDS_3812_2, IPDS_3812_2_00, IPDS_3816, IPDS_4028_1,
IPDS_4028_2, IPDS_4312, IPDS_4317, IPDS_4324, IPDS_4332)
IPDS_PRRES7. : 0
260
AXIS 5570e / AXIS 5670e User’s Manual
The Parameter List
IPDS_SYSL7. : 37 (37, 256, 259, 260, 273, 274, 275, 277, 278,
280, 281, 282, 284, 285, 286, 287, 288, 289, 290, 293, 297, 361,
420, 423, 424, 437, 500, 803, 819, 838, 852, 853, 857, 858, 860,
861, 863, 865, 870, 871, 880, 892, 893, 905, 912, 914, 920, 923,
924, 1004, 1026, 1069, 1140, 1141, 1142, 1143, 1144, 1145, 1146,
1147, 1148, 1149, 1252)
IPDS_PD7.
: PostScript (PostScript, PCL)
IPDS_SOJS7. :
IPDS_EOJS7. :
PREMUL7.
: 3816_CX (3287_CX, 3268_CX, 3262_CX, 4214_CX,
4224_CX, 4230_CX, 3812_CX, 3816S_CX, 3816_CX, 5224_TX, 5225_TX,
5256_TX, 4214_TX, 4230_TX, 3812_TX, 3816S_TX, 3816_TX,
5X27_001_TX, 5X27_002_KS_TX, 5X27_002_KSSM_TX, 5X27_003_TX,
5X27_005_TX)
SYSL7.
: 37 (37, 256, 260, 273, 274, 275, 277, 278, 280,
281, 282, 284, 285, 286, 287, 288, 289, 290, 293, 297, 340, 361,
500, 833, 836, 838, 870, 871, 892, 893, 1026, 1140, 1141, 1142,
1143, 1144, 1145, 1146, 1147, 1148, 1149, USER)
PASSTHR7.
: NO
MPL7.
: 66, ENA
MPP7.
: 132, ENA
LPI7.
: 6 (3, 4, 6, 8)
CPI7.
: 10 (5, 10, 12, 13.3, 15, 17, 18)
DCPI7.
: 5.0 (5.0, 6.0, 6.7, 7.5, 9.0)
AUTORI7.
: YES
LM7.
: 0, 0, 48
TM7.
: 26, 26, 74
LDSF7.
: 100, 100, 70
DEFBIN7.
: BIN1 (BIN1, BIN2, BIN3, BIN4, BIN5, BIN6,
MANUAL, ENVELOPE, CONTINUOUS)
PRDRIVER7.
: PCL5 (USER, GENERIC, PCL4, PCL5, IBM_PRO,
EPSON_FX, EPSON_FX_15CPI, EPSON_LQ, EPSON_LQ_8LPI,
EPSON_LQ_1600K, EPSON_LQ_KS)
--- IBM EMULATOR 8
IPDS_PREMUL8. : IPDS_4332 (IPDS_4224_C2, IPDS_4224_E3,
IPDS_3812_2, IPDS_3812_2_00, IPDS_3816, IPDS_4028_1,
IPDS_4028_2, IPDS_4312, IPDS_4317, IPDS_4324, IPDS_4332)
IPDS_PRRES8. : 0
IPDS_SYSL8. : 37 (37, 256, 259, 260, 273, 274, 275, 277, 278,
280, 281, 282, 284, 285, 286, 287, 288, 289, 290, 293, 297, 361,
420, 423, 424, 437, 500, 803, 819, 838, 852, 853, 857, 858, 860,
861, 863, 865, 870, 871, 880, 892, 893, 905, 912, 914, 920, 923,
924, 1004, 1026, 1069, 1140, 1141, 1142, 1143, 1144, 1145, 1146,
1147, 1148, 1149, 1252)
IPDS_PD8.
: PostScript (PostScript, PCL)
IPDS_SOJS8. :
IPDS_EOJS8. :
PREMUL8.
: 3816_CX (3287_CX, 3268_CX, 3262_CX, 4214_CX,
4224_CX, 4230_CX, 3812_CX, 3816S_CX, 3816_CX, 5224_TX, 5225_TX,
5256_TX, 4214_TX, 4230_TX, 3812_TX, 3816S_TX, 3816_TX,
5X27_001_TX, 5X27_002_KS_TX, 5X27_002_KSSM_TX, 5X27_003_TX,
5X27_005_TX)
SYSL8.
: 37 (37, 256, 260, 273, 274, 275, 277, 278, 280,
281, 282, 284, 285, 286, 287, 288, 289, 290, 293, 297, 340, 361,
500, 833, 836, 838, 870, 871, 892, 893, 1026, 1140, 1141, 1142,
1143, 1144, 1145, 1146, 1147, 1148, 1149, USER)
PASSTHR8.
: NO
MPL8.
: 66, ENA
MPP8.
: 132, ENA
LPI8.
: 6 (3, 4, 6, 8)
AXIS 5570e / AXIS 5670e User’s Manual
261
The Parameter List
CPI8.
: 10 (5, 10, 12, 13.3, 15, 17, 18)
DCPI8.
: 5.0 (5.0, 6.0, 6.7, 7.5, 9.0)
AUTORI8.
: YES
LM8.
: 0, 0, 48
TM8.
: 26, 26, 74
LDSF8.
: 100, 100, 70
DEFBIN8.
: BIN1 (BIN1, BIN2, BIN3, BIN4, BIN5, BIN6,
MANUAL, ENVELOPE, CONTINUOUS)
PRDRIVER8.
: PCL5 (USER, GENERIC, PCL4, PCL5, IBM_PRO,
EPSON_FX, EPSON_FX_15CPI, EPSON_LQ, EPSON_LQ_8LPI,
EPSON_LQ_1600K, EPSON_LQ_KS)
--- IBM SCS PAGE FORMAT
PCORI.
: NO
DWSISO.
: NO
BIN1.
: COR, LETTER,
BIN2.
: COR, LETTER,
BIN3.
: COR, LETTER,
BIN4.
: COR, LETTER,
BIN5.
: COR, LETTER,
BIN6.
: COR, LETTER,
MANUAL.
: COR, LETTER,
ENVELOPE.
: COR, LETTER,
CONTINUOUS. : COR, LETTER,
SIMBF.
: YES
0,
0,
0,
0,
0,
0,
0,
0,
0,
0
0
0
0
0
0
0
0
0
--- IBM SCS CPI MAPPING
FGID_DEFAULT. : 11
FGID_CPI5.
: 244, 11
FGID_CPI10. : 11, 204
FGID_CPI12. : 86, 230
FGID_CPI15. : 230, 281
FGID_CPI17. : 252, 281
FGID_CPI8COR. : 86
FGID_CPI20COR. : 281
FGID_CPI25COR. : 289
FGID_CPI27COR. : 290
PROPOCOR.
: 230
TYPOCOR.
: 230
--- IBM SCS JOB CONTROL
REINIT.
: YES
SUPFFBLANK. : NO
--- IBM 3270 OPTIONS
CASE.
: DUAL (DUAL, MONO)
BASCOL.
: BLACK, ENA
XSTRN.
: 0
AUTNL.
: 1
ADDNL.
: 1
FFWPB.
: 0
FFEOPB.
: 1
NULSUP.
: 0
FFCPOS.
: 0
AFEOPB.
: 0
--- IBM SCS EXTENDED EMULATION
XEMUL.
: YES
WARN.
: NO
SSUBST.
: YES
SBTS.
:
262
AXIS 5570e / AXIS 5670e User’s Manual
The Parameter List
TLIS.
TTRS.
FLIS.
EECS.
COBXEM.
CCLIS.
:
:
:
:
:
:
025 03C
03E 025
025 02F
025 041 058 049 053
SETALL (OFF, SETESC, SETALL)
025 050
--- UDS
--------- BAR
NUMBER TYPE WIDTH HEIGHT TEXT-MODE CHECK-MODE
--------------------------------------------------------------- SSTR
---------- MSTR
---------- IBM PRINTER DRIVER
PRDRIVERBASE. : PCL5 (GENERIC, PCL4, PCL5, IBM_PRO, EPSON_FX,
EPSON_FX_15CPI, EPSON_LQ, EPSON_LQ_8LPI, EPSON_LQ_1600K,
EPSON_LQ_KS)
SOJS.
: 1B 45 1B 26 6C 30 4C
EOJS.
: 1B 45
BACKSPS.
: 08
CRS.
: 0D
LFS.
: 0A
NLS.
: 0D 0A
FFS.
: 0C
SOS.
:
SIS.
:
BLKS.
:
GRNS.
:
BLUS.
:
REDS.
:
MAGS.
:
CYNS.
:
YELS.
:
BIN1S.
: 1B 26 6C 31 48
BIN2S.
: 1B 26 6C 34 48
BIN3S.
: 1B 26 6C 35 48
BIN4S.
: 1B 26 6C 32 30 48
BIN5S.
: 1B 26 6C 32 31 48
BIN6S.
: 1B 26 6C 32 32 48
MANUALS.
: 1B 26 6C 32 48
ENVELOPES.
: 1B 26 6C 36 48
CONTINUOUSS. : 1B 26 6C 31 48
CSIZS.
:
LAC.
: HP_PCL (DISABLE, HP_PCL, EPSON_LQ)
GRD.
: HP_PCL (DISABLE, HP_PCL, EPSON_LQ)
JOGS.
: 1B 26 6C 31 54
SSUS.
:
SBSET.
: PC850 (ECMA94, LATIN9, PC437, PC850, PC852,
PC857, PC858, PC874, PC891, PC903, PC904, PC942, ROMAN8,
USASCII, USER)
--- FONT
FGID CSSF SBSET SPACING PITCH HEIGHT STYLE
STROKE TYPEFACE STRING
---------------------------------------------------------------------------------
AXIS 5570e / AXIS 5670e User’s Manual
263
The Parameter List
FONT.
: 3,
UPRIGHT,MEDIUM,4102,
FONT.
: 5,
UPRIGHT,MEDIUM,4102,
FONT.
: 11,
UPRIGHT,MEDIUM,4099,
FONT.
: 12,
UPRIGHT,MEDIUM,4099,
FONT.
: 13,
UPRIGHT,MEDIUM,4099,
FONT.
: 18,
ITALIC,MEDIUM,4099,
FONT.
: 19,
UPRIGHT,MEDIUM,4200,
FONT.
: 20,
UPRIGHT,MEDIUM,4099,
FONT.
: 30,
UPRIGHT,MEDIUM,4099,
FONT.
: 38,
UPRIGHT,BOLD, 4102,
FONT.
: 39,
UPRIGHT,BOLD, 4102,
FONT.
: 40,
UPRIGHT,MEDIUM,4102,
FONT.
: 41,
UPRIGHT,MEDIUM,4099,
FONT.
: 42,
UPRIGHT,MEDIUM,4099,
FONT.
: 43,
ITALIC,MEDIUM,4099,
FONT.
: 46,
UPRIGHT,BOLD, 4099,
FONT.
: 60,
UPRIGHT,BOLD, 4099,
FONT.
: 66,
UPRIGHT,MEDIUM,4102,
FONT.
: 68,
ITALIC,MEDIUM,4102,
FONT.
: 69,
UPRIGHT,BOLD, 4102,
FONT.
: 70,
UPRIGHT,MEDIUM,4099,
FONT.
: 71,
ITALIC,MEDIUM,4099,
FONT.
: 72,
UPRIGHT,BOLD, 4099,
FONT.
: 80,
UPRIGHT,MEDIUM,4099,
FONT.
: 84,
UPRIGHT,MEDIUM,4099,
FONT.
: 85,
UPRIGHT,MEDIUM,4099,
FONT.
: 86,
UPRIGHT,MEDIUM,4099,
FONT.
: 87,
UPRIGHT,MEDIUM,4102,
FONT.
: 91,
ITALIC,MEDIUM,4099,
FONT.
: 108,
UPRIGHT,BOLD, 4099,
264
98, DEFAULT,FIXED,
1B 28 31 4F
98, DEFAULT,FIXED,
100,
0,
100,
0,
98,
DEFAULT,FIXED,
100,
0,
98,
DEFAULT,FIXED,
100,
0,
98,
DEFAULT,FIXED,
100,
0,
98,
DEFAULT,FIXED,
100,
0,
98, DEFAULT,FIXED,
1B 28 30 4F
98, DEFAULT,FIXED,
100,
0,
100,
0,
98,
DEFAULT,FIXED,
100,
0,
98,
DEFAULT,FIXED,
100,
0,
98,
DEFAULT,FIXED,
135,
0,
98,
DEFAULT,FIXED,
135,
0,
98,
DEFAULT,FIXED,
100,
0,
98,
DEFAULT,FIXED,
100,
0,
98,
DEFAULT,FIXED,
100,
0,
98,
DEFAULT,FIXED,
100,
0,
98,
DEFAULT,FIXED,
100,
0,
98,
DEFAULT,FIXED,
150,
0,
98,
DEFAULT,FIXED,
150,
0,
98,
DEFAULT,FIXED,
150,
0,
98,
DEFAULT,FIXED,
120,
0,
98,
DEFAULT,FIXED,
120,
0,
98,
DEFAULT,FIXED,
120,
0,
98,
DEFAULT,FIXED,
120,
0,
98,
DEFAULT,FIXED,
120,
0,
98,
DEFAULT,FIXED,
120,
0,
98,
DEFAULT,FIXED,
120,
0,
98,
DEFAULT,FIXED,
130,
0,
98,
DEFAULT,FIXED,
120,
0,
98,
DEFAULT,FIXED,
120,
0,
AXIS 5570e / AXIS 5670e User’s Manual
The Parameter List
FONT.
: 110,
UPRIGHT,BOLD, 4102,
FONT.
: 111,
UPRIGHT,BOLD, 4099,
FONT.
: 112,
ITALIC,MEDIUM,4099,
FONT.
: 155,
ITALIC,BOLD, 4101,
FONT.
: 158,
UPRIGHT,MEDIUM,4101,
FONT.
: 159,
UPRIGHT,BOLD, 4101,
FONT.
: 160,
UPRIGHT,MEDIUM,4148,
FONT.
: 162,
ITALIC,MEDIUM,4148,
FONT.
: 163,
UPRIGHT,BOLD, 4148,
FONT.
: 173,
UPRIGHT,LIGHT, 4148,
FONT.
: 175,
UPRIGHT,MEDIUM,4101,
FONT.
: 204,
UPRIGHT,MEDIUM,4102,
FONT.
: 221,
UPRIGHT,MEDIUM,4099,
FONT.
: 223,
UPRIGHT,MEDIUM,4099,
FONT.
: 225,
UPRIGHT,MEDIUM,4099,
FONT.
: 229,
UPRIGHT,MEDIUM,4099,
FONT.
: 230,
UPRIGHT,MEDIUM,4102,
FONT.
: 244,
UPRIGHT,MEDIUM,4099,
FONT.
: 245,
UPRIGHT,BOLD, 4099,
FONT.
: 252,
UPRIGHT,MEDIUM,4099,
FONT.
: 253,
UPRIGHT,BOLD, 4099,
FONT.
: 254,
UPRIGHT,MEDIUM,4099,
FONT.
: 258,
UPRIGHT,MEDIUM,4099,
FONT.
: 266,
UPRIGHT,BOLD, 4099,
FONT.
: 281,
UPRIGHT,MEDIUM,4102,
FONT.
: 289,
UPRIGHT,MEDIUM,4102,
FONT.
: 290,
UPRIGHT,MEDIUM,4102,
FONT.
: 751,
UPRIGHT,MEDIUM,4101,
FONT.
: 1051,
UPRIGHT,MEDIUM,4101,
FONT.
: 1053,
UPRIGHT,BOLD, 4101,
AXIS 5570e / AXIS 5670e User’s Manual
98,
DEFAULT,FIXED,
130,
0,
98,
DEFAULT,FIXED,
120,
0,
98,
DEFAULT,FIXED,
120,
0,
100, DEFAULT,PROP,
0,
110,
100, DEFAULT,PROP,
0,
110,
100, DEFAULT,PROP,
0,
110,
100, DEFAULT,PROP,
0,
110,
100, DEFAULT,PROP,
0,
110,
100, DEFAULT,PROP,
0,
110,
100, DEFAULT,PROP,
0,
110,
100, DEFAULT,PROP,
0,
110,
98,
DEFAULT,FIXED,
167,
0,
98,
DEFAULT,FIXED,
150,
0,
98,
DEFAULT,FIXED,
150,
0,
98,
DEFAULT,FIXED,
150,
0,
98,
DEFAULT,FIXED,
150,
0,
98,
DEFAULT,FIXED,
180,
0,
98,
DEFAULT,FIXED,
100,
0,
98,
DEFAULT,FIXED,
100,
0,
98,
DEFAULT,FIXED,
171,
0,
98,
DEFAULT,FIXED,
171,
0,
98,
DEFAULT,FIXED,
220,
0,
98,
DEFAULT,FIXED,
180,
0,
98,
DEFAULT,FIXED,
100,
0,
98,
DEFAULT,FIXED,
233,
0,
98,
DEFAULT,FIXED,
267,
0,
98,
DEFAULT,FIXED,
300,
0,
100, DEFAULT,PROP,
0,
80,
100, DEFAULT,PROP,
0,
100,
100, DEFAULT,PROP,
0,
100,
265
The Parameter List
FONT.
: 1056,
ITALIC,MEDIUM,4101,
FONT.
: 1351,
UPRIGHT,MEDIUM,4101,
FONT.
: 1653,
UPRIGHT,BOLD, 4101,
FONT.
: 2103,
UPRIGHT,BOLD, 4101,
FONT.
: 3840,
UPRIGHT,MEDIUM,4101,
FONT.
: 3841,
UPRIGHT,BOLD, 4101,
FONT.
: 3842,
ITALIC,MEDIUM,4101,
FONT.
: 3843,
ITALIC,BOLD, 4101,
FONT.
: 3844,
UPRIGHT,MEDIUM,4113,
FONT.
: 3845,
UPRIGHT,BOLD, 4113,
FONT.
: 3846,
ITALIC,MEDIUM,4113,
FONT.
: 3847,
ITALIC,BOLD, 4113,
FONT.
: 3848,
ITALIC,MEDIUM,4116,
FONT.
: 3849,
MEDIUM,4140,
1B
28 73
FONT.
: 3850,
UPRIGHT,MEDIUM,4148,
FONT.
: 3851,
UPRIGHT,BOLD, 4148,
FONT.
: 3852,
ITALIC,MEDIUM,4148,
FONT.
: 3853,
ITALIC,BOLD, 4148,
FONT.
: 3854,
MEDIUM,4148,
1B
28 73
FONT.
: 3855,
BOLD, 4148,
1B
28 73
FONT.
: 3856,
MEDIUM,4148,
1B
28 73
FONT.
: 3857,
BOLD, 4148,
1B
28 73
FONT.
: 3858,
UPRIGHT,MEDIUM,4168,
FONT.
: 3859,
UPRIGHT,BOLD, 4168,
FONT.
: 3860,
ITALIC,MEDIUM,4168,
FONT.
: 3861,
UPRIGHT,MEDIUM,4197,
FONT.
: 3862,
UPRIGHT,BOLD, 4197,
FONT.
: 3863,
ITALIC,MEDIUM,4197,
266
100, DEFAULT,PROP,
0,
100,
100, DEFAULT,PROP,
0,
120,
100, DEFAULT,PROP,
0,
160,
100, DEFAULT,PROP,
0,
240,
100, DEFAULT,PROP,
0,
0,
100, DEFAULT,PROP,
0,
0,
100, DEFAULT,PROP,
0,
0,
100, DEFAULT,PROP,
0,
0,
100, DEFAULT,PROP,
0,
0,
100, DEFAULT,PROP,
0,
0,
100, DEFAULT,PROP,
0,
0,
100, DEFAULT,PROP,
0,
0,
100, DEFAULT,PROP,
0,
0,
100, DEFAULT,PROP,
0,
0,
34 53
100, DEFAULT,PROP,
0,
0,
100, DEFAULT,PROP,
0,
0,
100, DEFAULT,PROP,
0,
0,
100, DEFAULT,PROP,
0,
0,
100, DEFAULT,PROP,
0,
0,
NONE,
34 53
100, DEFAULT,PROP,
0,
0,
NONE,
34 53
100, DEFAULT,PROP,
0,
0,
NONE,
35 53
100, DEFAULT,PROP,
0,
0,
NONE,
35 53
100, DEFAULT,PROP,
0,
0,
100, DEFAULT,PROP,
0,
0,
100, DEFAULT,PROP,
0,
0,
100, DEFAULT,PROP,
0,
0,
100, DEFAULT,PROP,
0,
0,
100, DEFAULT,PROP,
0,
0,
NONE,
AXIS 5570e / AXIS 5670e User’s Manual
The Parameter List
FONT.
: 3864, 100, DEFAULT,PROP,
ITALIC,BOLD, 4197,
FONT.
: 3865, 100, DEFAULT,PROP,
UPRIGHT,MEDIUM,4297,
FONT.
: 3866, 100, DEFAULT,PROP,
UPRIGHT,NONE, 4362,
1B 28 73 31 42
FONT.
: 3867, 100, DEFAULT,PROP,
UPRIGHT,NONE, 4362,
1B 28 73 34 42
FONT.
: 3868, 100, DEFAULT,PROP,
UPRIGHT,MEDIUM,16602,
FONT.
: 3869, 100, DEFAULT,PROP,
UPRIGHT,BOLD, 16602,
FONT.
: 3870, 100, DEFAULT,PROP,
ITALIC,MEDIUM,16602,
FONT.
: 3871, 100, DEFAULT,PROP,
ITALIC,BOLD, 16602,
FONT.
: 3872, 100, DEFAULT,PROP,
UPRIGHT,MEDIUM,16901,
FONT.
: 3873, 100, DEFAULT,PROP,
UPRIGHT,BOLD, 16901,
FONT.
: 3874, 100, DEFAULT,PROP,
ITALIC,MEDIUM,16901,
FONT.
: 3875, 100, DEFAULT,PROP,
ITALIC,BOLD, 16901,
FONT.
: 3876, 100, DEFAULT,PROP,
UPRIGHT,MEDIUM,16686,
1B 28 31 39 4D
FONT.
: 3877, 100, DEFAULT,PROP,
UPRIGHT,MEDIUM,31402,
1B 28 35 37 39 4C
FONT.
: 5687, 100, DEFAULT,PROP,
UPRIGHT,MEDIUM,16901,
FONT.
: 5707, 100, DEFAULT,PROP,
UPRIGHT,BOLD, 16901,
FONT.
: 5815, 100, DEFAULT,PROP,
ITALIC,MEDIUM,16901,
FONT.
: 5835, 100, DEFAULT,PROP,
ITALIC,BOLD, 16901,
FONT.
: 6199, 100, DEFAULT,PROP,
UPRIGHT,MEDIUM,4197,
FONT.
: 6219, 100, DEFAULT,PROP,
UPRIGHT,BOLD, 4197,
FONT.
: 6327, 100, DEFAULT,PROP,
ITALIC,MEDIUM,4197,
FONT.
: 6347, 100, DEFAULT,PROP,
ITALIC,BOLD, 4197,
FONT.
: 16951,100, DEFAULT,PROP,
UPRIGHT,MEDIUM,4101,
FONT.
: 16971,100, DEFAULT,PROP,
UPRIGHT,BOLD, 4101,
FONT.
: 17079,100, DEFAULT,PROP,
ITALIC,MEDIUM,4101,
FONT.
: 17099,100, DEFAULT,PROP,
ITALIC,BOLD, 4101,
FONT.
: 33335,100, DEFAULT,PROP,
UPRIGHT,MEDIUM,4113,
FONT.
: 33355,100, DEFAULT,PROP,
UPRIGHT,BOLD, 4113,
FONT.
: 33463,100, DEFAULT,PROP,
ITALIC,MEDIUM,4113,
FONT.
: 33483,100, DEFAULT,PROP,
ITALIC,BOLD, 4113,
AXIS 5570e / AXIS 5670e User’s Manual
0,
0,
0,
0,
0,
0,
0,
0,
0,
0,
0,
0,
0,
0,
0,
0,
0,
0,
0,
0,
0,
0,
0,
0,
0,
0,
0,
0,
0,
0,
0,
0,
0,
0,
0,
0,
0,
0,
0,
0,
0,
0,
0,
0,
0,
0,
0,
0,
0,
0,
0,
0,
0,
0,
0,
0,
0,
0,
0,
0,
267
The Parameter List
FONT.
: 33591,100, DEFAULT,PROP,
0,
UPRIGHT,MEDIUM,16602,
FONT.
: 33601,100, DEFAULT,PROP,
0,
UPRIGHT,BOLD, 16602,
FONT.
: 33719,100, DEFAULT,PROP,
0,
ITALIC,MEDIUM,16602,
FONT.
: 33729,100, DEFAULT,PROP,
0,
ITALIC,BOLD, 16602,
FONT.
: 34103,100, DEFAULT,PROP,
0,
UPRIGHT,MEDIUM,4148,
FONT.
: 34123,100, DEFAULT,PROP,
0,
UPRIGHT,BOLD, 4148,
FONT.
: 34231,100, DEFAULT,PROP,
0,
ITALIC,MEDIUM,4148,
FONT.
: 34251,100, DEFAULT,PROP,
0,
ITALIC,BOLD, 4148,
FONT.
: 41783,100, DEFAULT,PROP,
0,
UPRIGHT,MEDIUM,4116,
FONT.
: 41803,100, DEFAULT,PROP,
0,
UPRIGHT,BOLD, 4116,
FONT.
: 41911,100, DEFAULT,PROP,
0,
ITALIC,MEDIUM,4116,
FONT.
: 41931,100, DEFAULT,PROP,
0,
ITALIC,BOLD, 4116,
FONT.
: 50000,100, PC942,PROP,
0,
UPRIGHT,MEDIUM,28752,
1B
28 31 39 4B 1B 26 74 33 31 50
FONT.
: 50001,100, PC942,PROP,
0,
UPRIGHT,MEDIUM,28752,
1B
28 31 39 4B 1B 26 74 33 31 50
FONT.
: 50002,100, PC942,PROP,
0,
UPRIGHT,MEDIUM,28752,
1B
28 31 39 4B 1B 26 74 33 31 50
FONT.
: 50003,100, PC942,PROP,
0,
UPRIGHT,MEDIUM,28752,
1B
28 31 39 4B 1B 26 74 33 31 50
FONT.
: 50004,100, PC942,PROP,
0,
UPRIGHT,MEDIUM,28752,
1B
28 31 39 4B 1B 26 74 33 31 50
FONT.
: 50005,100, PC942,PROP,
0,
UPRIGHT,MEDIUM,28752,
1B
28 31 39 4B 1B 26 74 33 31 50
FONT.
: 50006,100, PC942,PROP,
0,
UPRIGHT,MEDIUM,28752,
1B
28 31 39 4B 1B 26 74 33 31 50
FONT.
: 50007,100, PC942,PROP,
0,
UPRIGHT,MEDIUM,28752,
1B
28 31 39 4B 1B 26 74 33 31 50
FONT.
: 50008,100, PC942,PROP,
0,
UPRIGHT,MEDIUM,28752,
1B
28 31 39 4B 1B 26 74 33 31 50
FONT.
: 50009,100, PC942,PROP,
0,
UPRIGHT,MEDIUM,28752,
1B
28 31 39 4B 1B 26 74 33 31 50
FONT.
: 50010,100, PC942,PROP,
0,
UPRIGHT,MEDIUM,28752,
1B
28 31 39 4B 1B 26 74 33 31 50
FONT.
: 50011,100, PC942,PROP,
0,
UPRIGHT,MEDIUM,28752,
1B
28 31 39 4B 1B 26 74 33 31 50
268
0,
0,
0,
0,
0,
0,
0,
0,
0,
0,
0,
0,
144,
144,
120,
108,
96,
96,
80,
101,
101,
84,
76,
67,
AXIS 5570e / AXIS 5670e User’s Manual
The Parameter List
FONT.
: 50012,100, PC942,PROP,
UPRIGHT,MEDIUM,28752,
1B
28 31 39 4B 1B 26 74 33
FONT.
: 50013,100, PC942,PROP,
UPRIGHT,MEDIUM,28752,
1B
28 31 39 4B 1B 26 74 33
FONT.
: 50014,100, PC942,PROP,
UPRIGHT,MEDIUM,28752,
1B
28 31 39 4B 1B 26 74 33
FONT.
: 50015,100, PC942,PROP,
UPRIGHT,MEDIUM,28752,
1B
28 31 39 4B 1B 26 74 33
FONT.
: 50016,100, PC942,PROP,
UPRIGHT,MEDIUM,28752,
1B
28 31 39 4B 1B 26 74 33
FONT.
: 50017,100, PC942,PROP,
UPRIGHT,MEDIUM,28752,
1B
28 31 39 4B 1B 26 74 33
FONT.
: 50018,100, PC942,PROP,
UPRIGHT,MEDIUM,28752,
1B
28 31 39 4B 1B 26 74 33
FONT.
: 50019,100, PC942,PROP,
UPRIGHT,MEDIUM,28752,
1B
28 31 39 4B 1B 26 74 33
FONT.
: 50020,100, PC942,PROP,
UPRIGHT,MEDIUM,28752,
1B
28 31 39 4B 1B 26 74 33
FONT.
: 50021,100, PC942,PROP,
UPRIGHT,MEDIUM,28752,
1B
28 31 39 4B 1B 26 74 33
FONT.
: 50022,100, PC942,PROP,
UPRIGHT,MEDIUM,28752,
1B
28 31 39 4B 1B 26 74 33
FONT.
: 50023,100, PC942,PROP,
UPRIGHT,MEDIUM,28752,
1B
28 31 39 4B 1B 26 74 33
FONT.
: 50030,100, PC891,PROP,
UPRIGHT,MEDIUM,43088,
1B
28 31 39 48 1B 26 74 33
FONT.
: 50031,100, PC891,PROP,
UPRIGHT,MEDIUM,43088,
1B
28 31 39 48 1B 26 74 33
FONT.
: 50032,100, PC891,PROP,
UPRIGHT,MEDIUM,43088,
1B
28 31 39 48 1B 26 74 33
FONT.
: 50033,100, PC891,PROP,
UPRIGHT,MEDIUM,43088,
1B
28 31 39 48 1B 26 74 33
FONT.
: 50034,100, PC891,PROP,
UPRIGHT,MEDIUM,43088,
1B
28 31 39 48 1B 26 74 33
FONT.
: 50035,100, PC891,PROP,
UPRIGHT,MEDIUM,43088,
1B
28 31 39 48 1B 26 74 33
FONT.
: 50036,100, PC891,PROP,
UPRIGHT,MEDIUM,43088,
1B
28 31 39 48 1B 26 74 33
FONT.
: 50037,100, PC891,PROP,
UPRIGHT,MEDIUM,43088,
1B
28 31 39 48 1B 26 74 33
AXIS 5570e / AXIS 5670e User’s Manual
0,
67,
31 50
0,
56,
31 50
0,
144,
31 50
0,
120,
31 50
0,
108,
31 50
0,
96,
31 50
0,
80,
31 50
0,
101,
31 50
0,
84,
31 50
0,
76,
31 50
0,
67,
31 50
0,
56,
31 50
0,
144,
38 50
0,
144,
38 50
0,
120,
38 50
0,
108,
38 50
0,
96,
38 50
0,
96,
38 50
0,
80,
38 50
0,
101,
38 50
269
The Parameter List
FONT.
: 50038,100, PC891,PROP,
UPRIGHT,MEDIUM,43088,
1B
28 31 39 48 1B 26 74 33
FONT.
: 50039,100, PC891,PROP,
UPRIGHT,MEDIUM,43088,
1B
28 31 39 48 1B 26 74 33
FONT.
: 50040,100, PC891,PROP,
UPRIGHT,MEDIUM,43088,
1B
28 31 39 48 1B 26 74 33
FONT.
: 50041,100, PC891,PROP,
UPRIGHT,MEDIUM,43088,
1B
28 31 39 48 1B 26 74 33
FONT.
: 50042,100, PC891,PROP,
UPRIGHT,MEDIUM,43088,
1B
28 31 39 48 1B 26 74 33
FONT.
: 50043,100, PC891,PROP,
UPRIGHT,MEDIUM,43088,
1B
28 31 39 48 1B 26 74 33
FONT.
: 50044,100, PC891,PROP,
UPRIGHT,MEDIUM,41040,
1B
28 31 39 48 1B 26 74 33
FONT.
: 50045,100, PC891,PROP,
UPRIGHT,MEDIUM,41040,
1B
28 31 39 48 1B 26 74 33
FONT.
: 50046,100, PC891,PROP,
UPRIGHT,MEDIUM,41040,
1B
28 31 39 48 1B 26 74 33
FONT.
: 50047,100, PC891,PROP,
UPRIGHT,MEDIUM,41040,
1B
28 31 39 48 1B 26 74 33
FONT.
: 50048,100, PC891,PROP,
UPRIGHT,MEDIUM,41040,
1B
28 31 39 48 1B 26 74 33
FONT.
: 50049,100, PC891,PROP,
UPRIGHT,MEDIUM,41040,
1B
28 31 39 48 1B 26 74 33
FONT.
: 50050,100, PC891,PROP,
UPRIGHT,MEDIUM,41040,
1B
28 31 39 48 1B 26 74 33
FONT.
: 50051,100, PC891,PROP,
UPRIGHT,MEDIUM,41040,
1B
28 31 39 48 1B 26 74 33
FONT.
: 50052,100, PC891,PROP,
UPRIGHT,MEDIUM,41040,
1B
28 31 39 48 1B 26 74 33
FONT.
: 50053,100, PC891,PROP,
UPRIGHT,MEDIUM,41040,
1B
28 31 39 48 1B 26 74 33
FONT.
: 50060,100, PC904,PROP,
UPRIGHT,MEDIUM,0,
FONT.
: 50061,100, PC904,PROP,
UPRIGHT,MEDIUM,0,
FONT.
: 50062,100, PC904,PROP,
UPRIGHT,MEDIUM,0,
FONT.
: 50063,100, PC904,PROP,
UPRIGHT,MEDIUM,0,
FONT.
: 50064,100, PC904,PROP,
UPRIGHT,MEDIUM,0,
FONT.
: 50065,100, PC904,PROP,
UPRIGHT,MEDIUM,0,
270
0,
101,
38 50
0,
84,
38 50
0,
76,
38 50
0,
67,
38 50
0,
67,
38 50
0,
56,
38 50
0,
144,
38 50
0,
120,
38 50
0,
108,
38 50
0,
96,
38 50
0,
80,
38 50
0,
101,
38 50
0,
84,
38 50
0,
76,
38 50
0,
67,
38 50
0,
56,
38 50
0,
144,
0,
144,
0,
120,
0,
108,
0,
96,
0,
96,
AXIS 5570e / AXIS 5670e User’s Manual
The Parameter List
FONT.
: 50066,100, PC904,PROP,
UPRIGHT,MEDIUM,0,
FONT.
: 50067,100, PC904,PROP,
UPRIGHT,MEDIUM,0,
FONT.
: 50068,100, PC904,PROP,
UPRIGHT,MEDIUM,0,
FONT.
: 50069,100, PC904,PROP,
UPRIGHT,MEDIUM,0,
FONT.
: 50070,100, PC904,PROP,
UPRIGHT,MEDIUM,0,
FONT.
: 50071,100, PC904,PROP,
UPRIGHT,MEDIUM,0,
FONT.
: 50072,100, PC904,PROP,
UPRIGHT,MEDIUM,0,
FONT.
: 50073,100, PC904,PROP,
UPRIGHT,MEDIUM,0,
FONT.
: 50074,100, PC904,PROP,
UPRIGHT,MEDIUM,0,
FONT.
: 50075,100, PC904,PROP,
UPRIGHT,MEDIUM,0,
FONT.
: 50076,100, PC904,PROP,
UPRIGHT,MEDIUM,0,
FONT.
: 50077,100, PC904,PROP,
UPRIGHT,MEDIUM,0,
FONT.
: 50078,100, PC904,PROP,
UPRIGHT,MEDIUM,0,
FONT.
: 50079,100, PC904,PROP,
UPRIGHT,MEDIUM,0,
FONT.
: 50080,100, PC904,PROP,
UPRIGHT,MEDIUM,0,
FONT.
: 50081,100, PC904,PROP,
UPRIGHT,MEDIUM,0,
FONT.
: 50082,100, PC904,PROP,
UPRIGHT,MEDIUM,0,
FONT.
: 50083,100, PC904,PROP,
UPRIGHT,MEDIUM,0,
FONT.
: 50100,100, PC903,PROP,
UPRIGHT,MEDIUM,37058,
1B
28 31 38 43 1B 26 74 33
FONT.
: 50101,100, PC903,PROP,
UPRIGHT,MEDIUM,37058,
1B
28 31 38 43 1B 26 74 33
FONT.
: 50102,100, PC903,PROP,
UPRIGHT,MEDIUM,37058,
1B
28 31 38 43 1B 26 74 33
FONT.
: 50103,100, PC903,PROP,
UPRIGHT,MEDIUM,37058,
1B
28 31 38 43 1B 26 74 33
FONT.
: 50104,100, PC903,PROP,
UPRIGHT,MEDIUM,37058,
1B
28 31 38 43 1B 26 74 33
FONT.
: 50105,100, PC903,PROP,
UPRIGHT,MEDIUM,37058,
1B
28 31 38 43 1B 26 74 33
FONT.
: 50106,100, PC903,PROP,
UPRIGHT,MEDIUM,37058,
1B
28 31 38 43 1B 26 74 33
FONT.
: 50107,100, PC903,PROP,
UPRIGHT,MEDIUM,37058,
1B
28 31 38 43 1B 26 74 33
AXIS 5570e / AXIS 5670e User’s Manual
0,
80,
0,
101,
0,
101,
0,
84,
0,
76,
0,
67,
0,
67,
0,
56,
0,
144,
0,
120,
0,
108,
0,
96,
0,
80,
0,
101,
0,
84,
0,
76,
0,
67,
0,
56,
0,
144,
38 50
0,
144,
38 50
0,
120,
38 50
0,
108,
38 50
0,
96,
38 50
0,
96,
38 50
0,
80,
38 50
0,
101,
38 50
271
The Parameter List
FONT.
: 50108,100, PC903,PROP,
UPRIGHT,MEDIUM,37058,
1B
28 31 38 43 1B 26 74 33
FONT.
: 50109,100, PC903,PROP,
UPRIGHT,MEDIUM,37058,
1B
28 31 38 43 1B 26 74 33
FONT.
: 50110,100, PC903,PROP,
UPRIGHT,MEDIUM,37058,
1B
28 31 38 43 1B 26 74 33
FONT.
: 50111,100, PC903,PROP,
UPRIGHT,MEDIUM,37058,
1B
28 31 38 43 1B 26 74 33
FONT.
: 50112,100, PC903,PROP,
UPRIGHT,MEDIUM,37058,
1B
28 31 38 43 1B 26 74 33
FONT.
: 50113,100, PC903,PROP,
UPRIGHT,MEDIUM,37058,
1B
28 31 38 43 1B 26 74 33
FONT.
: 50114,100, PC903,PROP,
UPRIGHT,MEDIUM,37058,
1B
28 31 38 43 1B 26 74 33
FONT.
: 50115,100, PC903,PROP,
UPRIGHT,MEDIUM,37058,
1B
28 31 38 43 1B 26 74 33
FONT.
: 50116,100, PC903,PROP,
UPRIGHT,MEDIUM,37058,
1B
28 31 38 43 1B 26 74 33
FONT.
: 50117,100, PC903,PROP,
UPRIGHT,MEDIUM,37058,
1B
28 31 38 43 1B 26 74 33
FONT.
: 50118,100, PC903,PROP,
UPRIGHT,MEDIUM,37058,
1B
28 31 38 43 1B 26 74 33
FONT.
: 50119,100, PC903,PROP,
UPRIGHT,MEDIUM,37058,
1B
28 31 38 43 1B 26 74 33
FONT.
: 50120,100, PC903,PROP,
UPRIGHT,MEDIUM,37058,
1B
28 31 38 43 1B 26 74 33
FONT.
: 50121,100, PC903,PROP,
UPRIGHT,MEDIUM,37058,
1B
28 31 38 43 1B 26 74 33
FONT.
: 50122,100, PC903,PROP,
UPRIGHT,MEDIUM,37058,
1B
28 31 38 43 1B 26 74 33
FONT.
: 50123,100, PC903,PROP,
UPRIGHT,MEDIUM,37058,
1B
28 31 38 43 1B 26 74 33
FONT.
: 50130,100, PC891,PROP,
UPRIGHT,MEDIUM,43088,
1B
28 31 38 48 1B 26 74 33
FONT.
: 50131,100, PC891,PROP,
UPRIGHT,MEDIUM,43088,
1B
28 31 38 48 1B 26 74 33
FONT.
: 50132,100, PC891,PROP,
UPRIGHT,MEDIUM,43088,
1B
28 31 38 48 1B 26 74 33
FONT.
: 50133,100, PC891,PROP,
UPRIGHT,MEDIUM,43088,
1B
28 31 38 48 1B 26 74 33
272
0,
101,
38 50
0,
84,
38 50
0,
76,
38 50
0,
67,
38 50
0,
67,
38 50
0,
56,
38 50
0,
144,
38 50
0,
120,
38 50
0,
108,
38 50
0,
96,
38 50
0,
80,
38 50
0,
101,
38 50
0,
84,
38 50
0,
76,
38 50
0,
67,
38 50
0,
56,
38 50
0,
144,
38 50
0,
144,
38 50
0,
120,
38 50
0,
108,
38 50
AXIS 5570e / AXIS 5670e User’s Manual
The Parameter List
FONT.
: 50134,100, PC891,PROP,
UPRIGHT,MEDIUM,43088,
1B
28 31 38 48 1B 26 74 33
FONT.
: 50135,100, PC891,PROP,
UPRIGHT,MEDIUM,43088,
1B
28 31 38 48 1B 26 74 33
FONT.
: 50136,100, PC891,PROP,
UPRIGHT,MEDIUM,43088,
1B
28 31 38 48 1B 26 74 33
FONT.
: 50137,100, PC891,PROP,
UPRIGHT,MEDIUM,43088,
1B
28 31 38 48 1B 26 74 33
FONT.
: 50138,100, PC891,PROP,
UPRIGHT,MEDIUM,43088,
1B
28 31 38 48 1B 26 74 33
FONT.
: 50139,100, PC891,PROP,
UPRIGHT,MEDIUM,43088,
1B
28 31 38 48 1B 26 74 33
FONT.
: 50140,100, PC891,PROP,
UPRIGHT,MEDIUM,43088,
1B
28 31 38 48 1B 26 74 33
FONT.
: 50141,100, PC891,PROP,
UPRIGHT,MEDIUM,43088,
1B
28 31 38 48 1B 26 74 33
FONT.
: 50142,100, PC891,PROP,
UPRIGHT,MEDIUM,43088,
1B
28 31 38 48 1B 26 74 33
FONT.
: 50143,100, PC891,PROP,
UPRIGHT,MEDIUM,43088,
1B
28 31 38 48 1B 26 74 33
FONT.
: 50144,100, PC891,PROP,
UPRIGHT,MEDIUM,41040,
1B
28 31 38 48 1B 26 74 33
FONT.
: 50145,100, PC891,PROP,
UPRIGHT,MEDIUM,41040,
1B
28 31 38 48 1B 26 74 33
FONT.
: 50146,100, PC891,PROP,
UPRIGHT,MEDIUM,41040,
1B
28 31 38 48 1B 26 74 33
FONT.
: 50147,100, PC891,PROP,
UPRIGHT,MEDIUM,41040,
1B
28 31 38 48 1B 26 74 33
FONT.
: 50148,100, PC891,PROP,
UPRIGHT,MEDIUM,41040,
1B
28 31 38 48 1B 26 74 33
FONT.
: 50149,100, PC891,PROP,
UPRIGHT,MEDIUM,41040,
1B
28 31 38 48 1B 26 74 33
FONT.
: 50150,100, PC891,PROP,
UPRIGHT,MEDIUM,41040,
1B
28 31 38 48 1B 26 74 33
FONT.
: 50151,100, PC891,PROP,
UPRIGHT,MEDIUM,41040,
1B
28 31 38 48 1B 26 74 33
FONT.
: 50152,100, PC891,PROP,
UPRIGHT,MEDIUM,41040,
1B
28 31 38 48 1B 26 74 33
FONT.
: 50153,100, PC891,PROP,
UPRIGHT,MEDIUM,41040,
1B
28 31 38 48 1B 26 74 33
AXIS 5570e / AXIS 5670e User’s Manual
0,
96,
38 50
0,
96,
38 50
0,
80,
38 50
0,
101,
38 50
0,
101,
38 50
0,
84,
38 50
0,
76,
38 50
0,
67,
38 50
0,
67,
38 50
0,
56,
38 50
0,
144,
38 50
0,
120,
38 50
0,
108,
38 50
0,
96,
38 50
0,
80,
38 50
0,
101,
38 50
0,
84,
38 50
0,
76,
38 50
0,
67,
38 50
0,
56,
38 50
273
The Parameter List
--- Email Menu
EMAIL_NOTIFICATION. : NO
REPLY_ADDRESS. :
PAPER_JAM_ADDRESS. :
OUT_OF_PAPER_ADDRESS. :
TONER_LOW_ADDRESS. :
NO_TONER_ADDRESS. :
PRINTER_OFFLINE_ADDRESS. :
274
AXIS 5570e / AXIS 5670e User’s Manual
The Parameter List
NetWare Parameter Combinations
In AXIS 5570e, when NetWare is enabled (i.e. when the NETW_ENB.
parameter is set to “yes” in the NetWare Menu), the different settings of
the NETW_TRANSPORT_PROTOCOL. and NDPS. parameters will result in
these functionalities:
NETW_ENB
YES
YES
YES
YES
YES
YES
YES
YES
YES
YES
YES
YES
Functionality
NETW_TRANSPORT_PROTOCOL
DUAL_STACK
DUAL_STACK
DUAL_STACK
DUAL_STACK
IP_ONLY
IP_ONLY
IP_ONLY
IP_ONLY
IPX_ONLY
IPX_ONLY
IPX_ONLY
IPX_ONLY
NDPS
TCP_AND_SPX
TCP_ONLY
SPX_ONLY
DISABLED
TCP_AND_SPX
TCP_ONLY
SPX_ONLY
DISABLED
TCP_AND_SPX
TCP_ONLY
SPX_ONLY
DISABLED
Functionality
1, 2, 3, 4, 5, 6, 7
1, 2, 3, 5, 6, 7
2, 3, 4, 5, 6, 7
3, 5, 6, 7
1, 2, 5
1, 2, 5
2, 5
5
2, 3, 4, 6, 7
2, 3, 6, 7
2, 3, 4, 6, 7
3, 6, 7
1. Raw TCP ports 9100 = LPT1 and 9101 = USB1 are opened for NDPS
printing. To create TCP NDPS printer objects, AXIS_PRINT_SYSTEM must
be enabled (see Note a).
2. The HP-MIB is enabled.
3. Services are SAP'ed and enabled on SPX sockets 8060 and 4114 (see
Notes b and c).
4. Print services are SAP'ed and enabled on SPX sockets, 400C = LPT1
and 401C = USB1 (see Notes b and c).
5. Pure IP queue mode printing is enabled.
6. IPX queue mode printing is enabled (see Note c).
7. Looking for SAP NetwWare fileservers on the net (see Note c).
Notes:
(a) TCP printing must be enabled (TCP_ENB. = YES).
(b) Some other SAP service must be present on the network.
(c) At least one frametype must be enabled for NetWare.
AXIS 5570e / AXIS 5670e User’s Manual
275
The Parameter List
TCP Ports Opened for Raw Printing
AXIS 5570e
Port Number
9100
9101
9900
9902
9100
9101
Port
LPT1
USB1
LPT1
USB1
LPT1
USB1
Via Logical Printer
—
—
—
—
—
—
Port Number
9100
9101
9102
9900
9901
9902
9100
9101
9102
Port
LPT1
LPT2
COM1
LPT1
COM1
LPT2
LPT1
LPT2
COM1
Via Logical Printer
—
—
—
—
—
—
—
—
—
Condition
DEFAULT_RAW_TCP. set to 9100
AXIS_PRINT_SYSTEM. Enabled
NDPS. Enabled
AXIS 5670e
Note:
Condition
DEFAULT_RAW_TCP. set to 9100
AXIS_PRINT_SYSTEM. Enabled
NDPS. Enabled
The TCP port numbers entered in RTEL_PRx. will override the settings in
the two tables above.
SNMP Device Index
When using the TCP/IP protocol (and if the printer driver permits), the
print server can use SNMP Status to find out if the printer is ready to
accept a new job.
By default, Windows uses the value “1” when addressing an SNMP
device, which is correct for single port print servers. For a multiport print
server, obtain the SNMP Device Index from the table below.
276
Print Server
LPR Queue Name
Raw Port Number SNMP Device Index
Single Port:
Parallel
LPT1
9100
1
Single Port:
USB
USB1
9100
1
Dual Port:
Parallel
USB
LPT1
USB1
9100
9101
1
2
AXIS 5570e / AXIS 5670e User’s Manual
The Parameter List
Enable SNMP Status
Example
Print Server
LPR Queue Name
Raw Port Number SNMP Device Index
Dual Port:
Parallel
Parallel
LPT1
LPT2
9100
9101
1
2
Three Port:
Parallel
Parallel
Serial
LPT1
LPT2
COM1
9100
9101
9102
1
3
2
SNMP Status is enabled through Windows’ printer port settings.
You have a three port print server and want to enable SNMP Status for
LPT2. The table above tells you to set the SNMP Device Index to 3.
Using Windows XP as an example:
1. Go to Start | Printers and Faxes.
2. Select Printer and then Properties.
3. Select Port and mark the Port you would like to change.
4. Click Configure Port...
5. Ensure that SNMP Status Enabled is ticked and enter the correct index
number in SNMP Device Index, taken from the table above (3 in this
example).
6. Click OK and Close.
AXIS 5570e / AXIS 5670e User’s Manual
277
Glossary
Section 27
Glossary
3270DS
Active Directory
AIX
APPC
AppleTalk
Active Directory - a structure supported by Windows 2000 that lets any
object on a network be tracked and located. Active Directory is the
directory service used in Windows 2000 Server and provides the
foundation for Windows 2000 distributed networks.
Advanced Interactive eXecutive. A version of the UNIX operating system
from IBM that runs on various IBM computers including Mainframe
systems.
Advanced Program-to-Program Communication. SNA facility (based on
LU6.2 and PU2.1) for general purpose inter-program communications.
Often used synonymously with LU6.2 but LU6.2 is the architecture and
APPC is the programming interface.
A local area network protocol for communication between Apple
Computer products and other computers and peripherals.
arp
Address Resolution Protocol. A protocol within the TCP/IP suite of
network protocols that allows a host to find the physical address of a
node on the same network. It is available in UNIX, Windows 95, Windows
98 and Windows NT. arp cannot be used across routers.
ASCII
American Standard Code for Information Interchange, a plain text format
used by computers.
Authentication
Verification of identity, for instance by use of digital signatures.
Auto-IP
A method to automatically set an IP address in the absence of a DHCP
server.
Bonjour
Bonjour enables automatic discovery of computers, devices, and services
on IP networks without the need to enter IP addresses or configure DNS
servers.
BOOTP
BOOT Protocol. A TCP/IP protocol, used for downloading start-up
information such as the IP address to hosts on the network. It is only
available in UNIX. BOOTP requires a BOOTP daemon on your system. A
request made to an active BOOTP daemon initiates a search of the Boot
Table for an entry matching the print server's Ethernet address. If a
matching entry is found, the daemon downloads the IP address to the
print server.
BSD
278
3270 Data Stream is a control language used for the 3270 family of
terminals and controllers. Also used for printing.
Berkeley Software Distribution. The University of California, Berkeley
additions to the UNIX operating system.
AXIS 5570e / AXIS 5670e User’s Manual
Glossary
Certificate Authority,
CA
An organization or company that issues digital certificates.
Client/server Printing
Means that print jobs are sent to a file server, with different clients
attached to the print queue, rather than directly to the print server (Peerto-Peer printing).
config file
This is a file that resides in the print server’s memory and contains all the
parameters that determine the Axis Network Print Server functionality.
By editing the config file (changing the parameter settings), you can
configure the Axis Network Print Server to meet the printing needs of
your network.
CPGID
Code Page Global ID
DHCP
Dynamic Host Configuration Protocol. Enables e.g. a print server to
automatically obtain an unused IP address from the DHCP server.
To fully benefit from this method, the print server also supports DDNS,
which is available in Windows 2000 networks.
Digital Certificate
DNS
Used to create digital signatures and public/private key pairs for secure
Web services.
Domain Name System. Resolves host names into IP addresses.
Dynamic DNS
Dynamic Domain Name System. Allows hosts to dynamically change the
IP address in DNS, e.g. when the host is given a new IP address by DHCP.
EBCDIC
Extended Binary Coded Decimal Interchange Code. Coded 8-bit character
set used by SNA and native IBM data streams.
FEP
Front End Processor. Generic term for a specialized computer linked to a
host machine to support a specialized function
(e.g. communications). IBM 3705, 3720, 3725, and 3745 are
communications FEPs.
Dynamic DNS
Firmware
Flash Memory
FTP
HPR
Dynamic Domain Name System. Allows hosts to dynamically change the
IPs address in DNS, e.g. when the host is given a new IP address by DHCP.
Firmware is the print server’s internal software.
The print server software is stored in Flash Memory.
File Transfer Protocol. A TCP/IP protocol used for logging in to network
servers and for transferring files.
High Performance Routing. IBM implementation of APPN (Advanced
Peer-to-Peer Networking). Includes pro-active congestion control and
non-disruptive re-routing
AXIS 5570e / AXIS 5670e User’s Manual
279
Glossary
HTML
HTTP
HTTPS
IP
IPDS
Hypertext Transfer Protocol. The TCP/IP protocol for Web based
communication.
HyperText Transmission Protocol, Secure, i.e. HTTP for secure
transactions.
Internet Protocol. The TCP/IP network-layer protocol that regulates
packet forwarding by tracking IP addresses, routing outgoing messages
and recognizing incoming messages.
Intelligent Printer Data Stream. An IBM protocol for data sent to page
printers. A page description language analogous to PostScript.
IPP
Internet Printing Protocol. A developing industry standard that allows
users to print to remote printers across the Internet. With IPP, a user with
an Internet connection can send a document to any printer connected to
the Internet. IPP is platform independent and can be used to print over
any LAN or WAN that supports TCP/IP.
IPX
Internetwork Packet Exchange, a networking protocol used by NetWare.
LAN
Local Area Network.
LED
Light Emitting Diode.
Linux
LLC
Logical Printer
280
Hypertext Markup Language. A standard hypertext language used for
creating World Wide Web pages and other hypertext documents.
An open source implementation of UNIX.
Logical Link Control. An additional data link layer protocol which
operates on top of the MAC protocol defined in the original Ethernet
standard (the "Blue Book").
A logical printer acts as a filter between the network and the physical
printer. It appears to the user as a normal printer with additional
characteristics. For example a UNIX workstation may only send a line
feed (LF) to a shared printer that needs carriage return (CR) and LF. The
logical printer can solve this problem by adding a CR.
LPD
The Line Printer Daemon is a protocol for transferring print jobs between
hosts. This is the recommended method for UNIX/Linux systems, but
some System V versions do not support LPD.
LPR
Line PRinter. The Unix print command. This does not actually print files
but rather copies or links them to a spool area from where a daemon
copies them to the printer.
AXIS 5570e / AXIS 5670e User’s Manual
Glossary
LU
Logical Unit. The user's port into an SNA network. LU1 is a high
performance print stream. LU2 is a 3270 terminal data stream. LU3 is a
3270 print data stream. LU6 is a host-to-host data exchange stream. LU7
is the 5250 terminal data stream.
LU6.2
IBM Peer-to-peer data stream for NOS functions. Supports asynchronous
(store-and-forward) networking.
MIB
Management Information Base. A database of network configuration
information used by SNMP and CMIP to monitor or change network
settings.
NAU
Network Addressable Unit. Entities within an SNA network (SSCP, PU,
LU) that can send or receive requests and responses. An SNA network is
made up of NAUs and the underlying path control network.
NCP
NetWare Core Protocol. Network clients use the NCP to request services of
servers, and servers use NCP to provide services, such as file and print
services.
NCP(2)
NDS
NetBIOS/NetBEUI
NetWare
Network Control Program. SNA program resident in the FEP. NCP offloads certain line protocol and routing functions from the host CPU.
NetWare Directory Services. A hierarchical data base that manages
NetWare network resources such as servers and volumes.
Network Basic Input Output System, a network protocol with special
functions for local area networks. NetBIOS Enhanced User Interface is an
enhanced version of NetBIOS.
An operating system for local area networks.
PCL
Printer Control Language — a set of command codes used when printing.
A PCL driver is a small program that works between the operating system
and the printer.
Peer-to-Peer Printing
When selecting Peer-to-peer printing, all print jobs are sent directly to the
print server, rather than through a file server (client/server).
PEM
Privacy Enhanced Mail.
PPR/PPD
Page Printer Requester/Page Printer Daemon. Bidirectional IBM
proprietary TCP/IP application protocol. Supported on AS/400s and
Mainframes for transporting IPDS printer data over TCP/IP. This is not an
open standard.
PU
Physical Unit type within SNA. The software in an SNA node controlling
the node's communications hardware.
AXIS 5570e / AXIS 5670e User’s Manual
281
Glossary
PU2.1
SNA PU type 2.1 allows local user ports to communicate without going
thorough a host node's SSCP services.s
RARP
Reverse Address Resolution Protocol. A TCP/IP protocol used for
downloading IP addresses in UNIX/Linux networks. It requires a RARP
daemon on your system, and only operates within a single network
segment. A request made to an active RARP daemon initiates a search of
the Ethernet Address Table for an entry matching the print server's
Ethernet address. If a matching entry is found, the daemon downloads the
IP address to the print server.
RISC
Reduced Instruction Set Computing. A processor that recognizes only a
limited number of assembly-language instructions.
SAP
Service Advertising Protocol. A NetWare network name advertising
service that e.g. file servers can use for advertising their existence to
network clients.
SAP(2)
282
Service Access Point. Field defined by the IEEE 802.2 specification that is
part of an address specification. Thus, the destination plus the DSAP
define the recipient of a packet. The same applies to the SSAP
SCS
SNA Character String. A sequence of control commands that allows
sophisticated control of printers and other devices.
SNA
Systems Network Architecture. IBM's data communications architecture
defining levels of protocols for communications between terminals and
applications as well as between programs. Originally SNA was strictly
host-based with VTAM controlling the network except for path control
which was provided by NCP in the FEP. Recently, with the APPN/APPC
and HPR additions SNA has become more distributed.
SNMP
Simple Network Management Protocol. Standard management protocol
for network attached devices.
SPX
Sequenced Packet Exchange, a NetWare communications protocol used to
transmit messages reliably over a network.
SSCP
System Services Control Point. SNA software within VTAM which
handles network name/address conversion, device configuration, network
diagnostics and recovery. The SSCP is a NAU located on a host node in
the network.
SSL
Secure Sockets Layer, a protocol designed to provide secure
communications on the Internet.
TCP
Transmission Control Protocol. The connection-oriented, transport-level
protocol used in the TCP/IP suite of protocols.
AXIS 5570e / AXIS 5670e User’s Manual
Glossary
Telnet
TFTP
TLS
A terminal emulation program for networks, often used to remotely
control Web servers.
Trivial File Transfer Protocol (TFTP) is an Internet software utility for
transferring files that is simpler to use than the File Transfer Protocol
(FTP) but less capable. It is used where user authentication and directory
visibility are not required. TFTP uses the User Datagram Protocol (UDP)
rather than the Transmission Control Protocol (TCP).
Transport Layer Security, a protocol that guarantees privacy and data
integrity between applications communicating over the Internet.
TN3270E
Extension to the Telnet protocol for transporting 3270 terminal and print
data over TCP/IP.
TN5250E
Extension to the Telnet protocol for transporting 5250 terminal and print
data over TCP/IP.
UNIX
A 32-bit multi-tasking, multi-user operating system originally developed
by AT&T.
URL
Uniform Resource Locator. A way of specifying the location of publicly
available information on the Internet.
USB
Universal Serial Bus.
VPDI
Virtual Printer Driver Interface
VTAM
Virtual Telecommunications Access Method. Mainframe software that
performs network control and management. VTAM's most important
objective is to provide the SSCP services.
WAN
Wide Area Network.
WINS
Windows Internet Name Service. A NetBIOS Name Server that maps
NetBIOS names to dynamically assigned IP addresses.
Wizard
A special form of user assistance that automates a task through a dialog
with the user. Wizards help the user to accomplish tasks that are complex
and require experience.
AXIS 5570e / AXIS 5670e User’s Manual
283
Index
Index
Numerics
3270DS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 278
A
Account file. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 136, 137
Active Directory . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 278
Addressing
Auto-IP. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 206
DHCP . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 205
Static . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 205
Admin . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 128
AIX . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 278
APPC . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 278
AppleTalk . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 85, 278
AS/400 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 22
ASCII . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 278
ASCII to Postscript Conversion . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 157
Authentication . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 278
Autodetect . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 85
Autodetect Printer Type . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 87
Auto-IP . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 17, 144, 278
Address Structure . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 17
Addressing . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 206
AXIS AddPrinter Wizard. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 64
AXIS IPP Gateway Configuration . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 103
AXIS LPR Gateway Configuration . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 103
AXIS MIB. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 140
AXIS Network Product CD . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12
AXIS Print Monitor . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 75
AXIS Print Utility for OS/2 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 126
AXIS ThinWizard
Installing . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 133
B
Backside label . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11
Bar Codes . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 179
Bar codes . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 180
Basic setup
AXIS NetPilot . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 108
BCP and TBCP . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 86
Bi-directional Printing. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 159
Bin
Default Input . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 193
Binary Protocol for Printer . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 87
Bonjour . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 278
Change Service Name. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 83
Printing . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 82
BSD . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 278
284
AXIS 5570e / AXIS 5670e User’s Manual
Index
C
CA . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 279
Certificate Authority . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 279
Certificates . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 164
Delete . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 166
Import . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 165
View . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 166
Change Bonjour Service Name . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 83
Changing Language in the Print Server’s Web Interface . . . . . . . . . . . . . . . 145
Character Set Conversion . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 154
Checking SSL/TLS Status . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 166
Client/Server Printing . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 279
Color . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 192
Compatible Printers. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11
Concentrator gateway, general . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 177
Concentrator gateway, Microsoft . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 178
Concentrator gateway, NetWare . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 177
config file . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 128, 279
Configuration and Management . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11
Configuration methods
FTP . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 135
NetWare Administrator . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 114, 141
PCONSOLE . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 114, 141
SNMP . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 140
Telnet . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 137
Web browser . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 129
Configuration Mode . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 179
Configuration Wizard . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 28, 41
Configuring
AS/400 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 29
IBM Mainframes. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 37
Conversions. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 154, 155, 157
Copier Model. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 202
Copiers . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 213
CPGID . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 279
CPI . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 182
Creating a Network Group . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 134
D
DBCS. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 197
Font Types . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 200
DDNS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 21, 206
DDNS Host Name Rules. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 206
Debugging. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 160
Hex Dump Mode. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 160
Print Problems . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 160
Default Gateway/Router . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 204
Default Input Bin . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 193
Delete Certificate . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 166
Device Features . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 198
DEVICE Statement. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 57
AXIS 5570e / AXIS 5670e User’s Manual
285
Index
DHCP Addressing. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 205
DHCP Enabled parameter . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 17
Digital Certificate . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 279
Digital Copier printing. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 203
Digital Copier Support. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 202
Disabling Protocols . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 166
DNS. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 279
DSPU . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 177
Duplex. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 192
Dynamic DNS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 279
Dynamic IP address Assignment . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 16
E
EBCDIC . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 279
Enable SNMP Status . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 277
Enable/disable SNMP . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 133
Enabling Protocols . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 166
Enabling SSL . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 164
Enabling the SNMPv3 Protocol . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 167
Ethernet Address . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 20
F
Factory Default . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 132, 208
Factory default settings . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 208
FEP . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 279
Firmware. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 279
Upgrade . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 132
Flash Loading over the Web . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 162, 169
Flash Memory . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 279
Fonts
Scalable . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 196
Selection . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 179
Smoothing . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 193
Typographical . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 196
Width . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 196
FSS Statement. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 54
FSSDEF Statement. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 56
FTP . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 135, 279
FTP Enabled. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 135, 170
FTP_ENB . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 133
G
Gateway
Default . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 204
H
Hardware Inventory. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8
Hex Dump Mode . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 160
Hex Transparancy . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 179
286
AXIS 5570e / AXIS 5670e User’s Manual
Index
Host Name . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 21, 206
DDNS Rules . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 206
WINS Rules. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 206
HPR. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 279
HTML. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 280
HTTP . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 280
HTTPS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 165, 280
I
IBM Capabilities . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 212
IBM Font Selection . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 182
IBM SNA . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 36
Importing a Certificate . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 165
Indicators . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11, 209
Installation guide . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15
Installation in Mac OS X using AppleTalk . . . . . . . . . . . . . . . . . . . . . . . . . . . 84
Installation of LPR printing in MAC OS X . . . . . . . . . . . . . . . . . . . . . . . . . . . 84
Installation Summary . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15
Installing AXIS ThinWizard . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 133
Internet Address . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 108
Internet Printing Protocol . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 146
IP . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 280
IP Address . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 204
Automatic Assignment Methods. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 16
Checking, using Ping. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 210
Default Gateway Example. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 205
Manual Assignment Methods . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 16
Setting - Macintosh . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 87
Setting, using Auto-IP . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 17
Setting, using DHCP . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 207
Setting, using RARP . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 207
Subnet Mask. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 204
Subnet Mask Structures . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 204
IPDS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 280
IPP. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 280
Client . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 146
Printing Requirements . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 147
IPP Printing . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 146
iPrint . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 89, 141
IPX . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 280
L
LAN . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 280
Last Code Point . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 198
LED . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 209, 280
Linux . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 280
LLC . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 177, 280
Local Printer . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 64, 72
Logical Link Control. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 280
Logical Printer . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 280
Logical Printers . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 154
AXIS 5570e / AXIS 5670e User’s Manual
287
Index
Logon-mode Entry. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 38
LPD . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 123, 280
LPR . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 280
LU . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 281
LU6.2. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 281
M
Macintosh
Choosing a Printer . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 85
Installing the Print Server . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 85
MIB . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 281
Microsoft SNA. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 178
Mounting the AXIS 5570e. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10
N
NAU . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 281
NCP. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 281
NCP(2). . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 281
NDPS. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 89
NDS. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 110, 281
NetBIOS/NetBEUI . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 281
NetWare . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 281
Advanced installation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 110
Basic installation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 108
NDPS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 89, 147
NetWare Packet Signature . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 162
NetWare Parameter Combinations . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 275
NetWare printing modes
Print Server Mode. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 113
Remote Printer Mode . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 113
NetWare SAA . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 177
Network
Client/Server. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 63
Indicator. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11, 209
Peer-to-Peer. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 64
Printer . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 63, 73
Speed . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 161
Structures. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 63
Network Connector . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11
Network Group
Create. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 134
Network Indicator . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11
O
Obtaining an IP Address and Subnet Mask . . . . . . . . . . . . . . . . . . . . . . . . .
OS/2
AXIS Print Utility for OS/2 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Installing the print server . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Overriding Port Status. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
288
205
126
126
168
AXIS 5570e / AXIS 5670e User’s Manual
Index
P
Package Contents . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8
Paper Size
Physical . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 193
Parameter Combinations. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 275
Parameter List . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 132, 208, 216
Pass-through gateway . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 177
PCL . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 281
Peer-to-Peer Printing . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 281
PEM . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 281
Point size . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 196
Port status
Override . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 168
Ports . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11
Opened for Raw Printing . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 276
Power
Indicator. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11, 209
PPR/PPD . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 281
Print Jobs
Redirect . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 159
Print Problems
Debugging . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 160
Printer
Autodetect . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 85
Ports . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11
Printer Driver. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 28, 41
Printer Emulation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 28, 41
Printing
Bi-directional . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 159
Client/Server. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 279
Parameter List . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 208
Peer-to-Peer. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 281
Test Page . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 208
Protocols
Disable . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 166
Enable . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 166
PRTnnnn Statement . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 55
PU . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 281
PU2.1 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 282
Pure IP . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 112
Q
Queue-based printing . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 89
R
RARP . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Raw Printing . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Redirecting Print Jobs . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Restart . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
RISC . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
AXIS 5570e / AXIS 5670e User’s Manual
282
276
159
132
282
289
Index
S
SAP . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 282
SAP(2) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 282
SBCS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 199
SCS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 282
SDLC . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 177
Secure Web Services . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 164
Security Settings . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 131
Server Report . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 211
Setting the Internet address
BOOTP . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 19
DHCP . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 20
RARP . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 18
Setting up
IBM SNA. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 22, 36
Macintosh . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 82
NetWare . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 89
OS/2 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 125
UNIX. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 115
Windows . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 63
SNA. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 282
SNA Printing
3174 CU Mode . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 29
5494 CU Mode . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 22, 36
Snap-in for iPrint . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 103
SNMP . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 140, 282
SNMP Device Index . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 64, 141, 210, 276
SNMP Status. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 276
SNMPv3 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 167
SPX . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 282
SSCP . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 282
SSL . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 164, 282
SSL/TLS
Status . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 166
Starting AXIS ThinWizard . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 133
Static Addressing . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 205
Status file . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 137, 138
String Functions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 155
String Substitutions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 156, 179
Subnet Mask . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 204
Substitutions. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 156
Support . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 211
Switched major node definitions. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 39
T
TCP . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 282
TCP Ports Opened for Raw Printing . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 276
TCP printing restriction list . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 163
Tcpmon.ini. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 71
Technical Assistance . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 211
Technical Specifications . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 202
290
AXIS 5570e / AXIS 5670e User’s Manual
Index
Telnet . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 283
Test Button . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11, 208
Test Page. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 208
TFTP. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 19, 20, 283
TLS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 164, 283
TN3270E . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 283
TN3270E Printing . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 42
TN5250E . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 283
TN5250E Printing . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 29
Troubleshooting . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 209
U
UNIX . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
UNIX/Linux Printing Methods
FTP . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
LPD . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
PROS A . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
PROS B . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Reverse Telnet . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Update Initial User . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Upgrading . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
URL . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
USB . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
User. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
User Defined Strings . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
283
123
123
124
124
124
167
169
283
283
128
179
V
View Certificate . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 166
VPDI . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 283
VTAM . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 283
VTAM Logon-mode entry. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 38
W
WAN . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 283
Web Flash Loading . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 162
WINS. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 20, 21
Host Name Rules . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 206
Wizard . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 283
World Wide Web . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 188
AXIS 5570e / AXIS 5670e User’s Manual
291
">