Advertisement
Advertisement
Vidifox
®
Document Camera
PV 380
USER MANUAL
Please read this User Manual thoroughly before you use the document camera. Keep the CD-ROM in a convenient place so you can use it quickly if you need to.
Please visit us at http://www.waninusa.com where you can get product support, the latest driver updates, and answers to frequently asked questions (FAQs) and technical questions.
1
PRECAUTIONS
NOTICES: PLEASE READ CAREFULLY BEFORE USE
Use the document camera under the rated electric conditions.
Do not place the document camera on any unstable surface. It may fall and cause injuries or damages.
Do not place this device directly under sunlight or near heaters.
Do not place this device near water.
Keep the camera away from acid or alkali gas.
Do not place this document camera in humid, dusty, windy or vibrant locations.
The recommended operating environment is:
Temperature: 32ºF-113ºF (0ºC--45ºC)
Humidity: less than 75%
Always unplug BEFORE cleaning the device. Use a damp soft-cloth for cleaning. Do not use volatile solvent.
When this equipment functions abnormally, such as smoke, smell, noise, immediately unplug and call for professional assistance.
Unplug the document camera or shut off the power when not in use.
Legal Notice
FCC Part 15
This device complies with Part 15 of the FCC Rules. Operation of this product is subject to the following two conditions: (1) this device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation.
Compilation and Publication Notice
This manual has been compiled and published to cover the latest product’s descriptions and specifications. The contents of this manual and the specifications of this product are subject to change without notice.
Wanin USA reserves the right to make changes without notice in the specifications and materials contained herein and shall not be responsible for any damages (including consequential) caused by reliance on the materials presented, including but not limited to typographical and other errors relating to the publication.
© 2010 Wanin USA Inc. All Rights Reserved.
2
TABLE OF CONTENTS
1 . PARTS IDENTIFICATION ................................................................. 4
2. CONTROL PANEL .............................................................................. 5
3. INPUTS AND OUTPUTS .................................................................... 6
4. REMOTE CONTROL ......................................................................... 7
5. CONNECTIONS ................................................................................... 9
5.1. COMPUTER CONNECTION ........................................................................................... 9
5.2. VGA OUTPUT CONNECTION ...................................................................................... 10
5.3. C-VIDEO OUTPUT CONNECTION .............................................................................. 10
5.4. S-VIDEO OUTPUT CONNECTION .............................................................................. 11
6. COMMUNICATE WITH COMPUTER .......................................... 11
6.1. COMPUTER REQUIREMENTS .................................................................................... 11
6.2. CONTROL VIA RS232 ................................................................................................... 11
6.3. USB CAMERA ................................................................................................................ 17
7. FEATURES ......................................................................................... 22
LIGHT ..................................................................................................................................... 22
ZOOM IN AND ZOOM OUT ................................................................................................ 22
FOCUS ADJUSTMENT ......................................................................................................... 22
BRIGHTNESS ADJUSTMENT ............................................................................................. 23
WHITE BALANCE ADJUSTMENT ..................................................................................... 23
TEXT/PICTURE MODE ........................................................................................................ 23
IMAGE FREEZE .................................................................................................................... 23
IMAGE MIRROR ................................................................................................................... 23
SPLIT SCREEN ...................................................................................................................... 23
IMAGE SAVE ......................................................................................................................... 23
IMAGE RECALL ................................................................................................................... 23
MULTIPLE INPUTS AND OUTPUTS .................................................................................. 24
USB 2.0 PORT ........................................................................................................................ 24
USB IMAGE CAPTURE AND VIDEO RECORDING ......................................................... 24
RS232 CONTROL .................................................................................................................. 24
8. SPECIFICATION ............................................................................... 24
9. TROUBLE-SHOOTING: .................................................................. 25
10. PACKING LIST ................................................................................ 26
3
1
. PARTS IDENTIFICATION
1.
Remote control IR receiver
2.
Camera
3.
LED light box
4.
Upper mechanical arm
5.
Main mechanical arm
6.
Side panel
7.
Back panel
8.
Base unit
9.
Control panel
4
2. CONTROL PANEL
1.
POWER : Turn on/off the power.
2.
HOME : Activate VGA output terminal, providing the image from camera.
3. LAMP : Turn on/off the LED light.
4.
FREEZE : Freeze/unfreeze the image.
5. T/P : Switch the output image between text mode and picture mode.
6.
SPLIT : Split screen, enable the comparison between the frozen image and live image.
7.
COMPUTER : Activate the VGA input.
8. VIDEO : Activate the C-VIDEO&S-VIDEO output, providing the image from camera.
9. BRIGHT+/: Image brightness adjustment.
10. PAGE DOWN : Saved image page down when image recall mode is enabled.
11. AUTO : Automatically adjust focus, color and white balance.
12. SAVE : Capture and save the current image.
13.
RECALL : Image recall mode enabled, display the saved images.
In Image Recall mode:
1 : Display the first image.
2 : Display the second image.
3 : Display the third image.
4 : Display the fourth image.
14.
FOCUS+/: Adjust focus manually, focus far and focus near.
15.
ZOOM+/: Image zoom in and zoom out control.
5
3. INPUTS AND OUTPUTS
1. DC 12V : Power input.
2. RS 232 : Serial port, to control the document camera from a computer via this port.
3. AUDIO OUT : Audio output.
4. VGA OUT : VGA (RGB) signal output (15 pin D-SUB).
5. C-VIDEO : Composite video output.
6. S-VIDEO : S-Video output.
7. VGA IN : VGA (RGB) signal input(15 pin D-SUB).
8. AUDIO IN : Audio input.
9. USB : Capture image into a connected computer via provided software
6
4. REMOTE CONTROL
7
1.
: Turn the document camera on or off .
2.
Computer : Press this button to output signals from VGA-IN.
3. Video : Activate the VIDEO&S-VIDEO output, providing the image from camera.
4. XGA/SXGA : Toggle the output format between XGA and SXGA.
5. Home : Output the image from the document camera.
6. Number Buttons :
In image recall mode:
1 : Display the first image.
2 : Display the second image.
3 : Display the third image.
4 : Display the fourth image.
7. : Turn the LED light on or off.
8. Mir : Output right-and-left, up-and-down mirror image.
9. Save : Capture the current image.
10.
Recall : Enter the Image Recall mode to display saved images.
11. Page +/: in Image Recall mode, navigate between pages of thumbnail images.
12. Auto : Automatic adjust focus, color and white balance.
13. Split : Split screen, enable the comparison between the frozen image and live image.
14. Zoom+/: Image zoom in and zoom out control.
15. Frz : Freeze/unfreeze the image.
16. Bri+/: Image brightness adjustment.
17. T/P : Switch the output image between the text mode and picture mode .
18. Fc+/: Adjust focus manually, focus far and focus near.
20. Sharp+/: Adjust sharpness of the image.
21.
Blue + /: Image color adjustment (blue).
22. Red +/ : Image color adjustment (red).
8
5. CONNECTIONS
5.1. COMPUTER CONNECTION
RS232 cable
Audio Cable
USB
To Audio Output
To RGB Output
To RS232
9
5.2. VGA OUTPUT CONNECTION
5.3. CVIDEO OUTPUT CONNECTION
To Audio Input
To Video Input
Audio Cable
Video Cable
10
5.4. S-VIDEO OUTPUT CONNECTION
S-Video Cable
Audio Calbe
To S-Video in
To Audio input
6. COMMUNICATE WITH COMPUTER
6.1. COMPUTER REQUIREMENTS
The PC's hardware and software configurations shall not be less than the following requirements ：
Operating system: Windows XP
CPU: 1.8 GHz
Physical memory: 512M
Video memory: 64M
6.2. CONTROL VIA RS232
PV 380 can be controlled from a computer via RS232.
1. Double click on the RS232 software in provided CD to run the install shield wizard.
11
Then you will see the software setup window:
Read terms, select "I accept the terms in the license agreement " Click on Next :
Click on Change to change the installation directory if needed, then click on Next :
12
Click on Install to install the software to the computer:
Click on Finish, the software installation is complete:
13
2. Connect the computer to the PV 380 with a RS232 cable, turn on the power of PV 380.
3. Double click on or click on start -> All Programs -> Visualizer_RS232 ->
Visualizer_RS232.exe to run the RS232 software, You will see the icon on the task bar and the control interface on the top right of the screen:
: Zoom+
: Zoom-
: Auto
: Display all functions
: Minimize
: Close
4. Click on , you will see the following control panel.
14
5. Properly set the software.
: Select corresponding model number.
Note:
: Select the right COM port.
* If the selected model does not have certain functions, the corresponding buttons in the software interface are displayed in light gray and are not clickable.
* All models require 15 seconds start-up time to start the software.
15
6. Button instruction
Button Function
Power On
Power on the unit
Power Off Standby
Home Switch to visualize mode
Video Out Switch to Video/S-Video output
PC In
Active PC input
Freeze
Image freeze
Light Toggle between arm light and no light
Brightness+ Increase the brightness
Brightness- Decrease the brightness
Focus+
Focus far
Focus- Focus near
Zoom+
Zoom in
Zoom-
Zoom out
Page+ Page up
Page- Page down
Red+
Increase the red hue
Red-
Decrease the red hue
Blue+ Increase the blue hue
Blue- Decrease the blue hue
Sharpness+ Increase the sharpness
16
Sharpness- Decrease the sharpness
Auto
Auto focus, brightness, and color
Save
Save image
Recall Recall saved images
Split Split screen
Mirror
Mirror image
T/P
Switch between text and image modes
XGA Switch between SXGA and XGA output modes
1
Display Image #1(in image recall mode)
2
Display Image #2(in image recall mode)
3
Display Image #3(in image recall mode)
4 Display Image #4(in image recall mode)
6.2 USB CAMERA
You can capture images and videos on the PV 380 from a computer via USB.
1. Connect the computer and the PV 380 with a USB cable, turn on the power of PV 380.
2. Open My Computer , you will see a USB Video Device:
17
3. Double click on USB Video Device, you will see the following image capture window:
To capture the video, please see the following steps:
1. Copy the USB software that in the provided CD into the folder PV 380.
2. Open the USB folder, double click to run the USB capture application:
You will see the following window:
18
2. Please make sure the software is in properly setting.
Make sure to select Devices -> USB video device and Options -> Preview.
19
3. Click on File -> Set Capture File to set the capture file.
A. Set the location and file name.
B. Set the file size.
4. Click on OK to finish the setup, then click on Capture -> Start capture to capture video.
20
4. You will see the following window, click on OK to start capture.
6. Click on Capture -> Stop Capture to stop
21
7. FEATURES
LIGHT
The PV 380 is the environmentally friendly product, it is RoHS compliant, which means it meets the rigorous European Union’s requirements for restriction of the use of certain hazardous substances in electrical and electronic equipment. The lighting box of PV 380 adopts eco-friendly, low power consumption and long lasting LED lamps, which is cool to the touch and mercury content free.
ZOOM IN AND ZOOM OUT
9x optical zoom combined with 8x seamless digital zoom, the PV 380 enables you to view the finest details of any objects that are impossible to see with your naked eyes. The PV 380’s advanced optical system features high speed auto focus capability that ensures instant auto focus when you quickly zoom in and out of any object. You can also manually adjust focus to satisfy any special viewing needs by pressing "ZOOM+"or "ZOOM
－
".
FOCUS ADJUSTMENT
When the Visualizer is turned on the focus automatically adjusts to the stage, it is not necessary to readjust the focus if you are only working with flat materials (text, photos, etc.). Only 3D objects
22
require a focus adjustment. Press the “AUTO” button to auto focus. Press the "FOCUS+" or
"FOCUS-" button to focus manually.
BRIGHTNESS ADJUSTMENT
If the image effect is not satisfactory, you can adjust the brightness to get a better image effect.
Use the “BRIGHT +” or “BRIGHT -” button to adjust the brightness. To increase the brightness, press the “BRIGHT +” button. To decrease it, press the “BRIGHT -” button.
WHITE BALANCE ADJUSTMENT
Each time the lighting condition changes, the user should adjust the white balance of the image.
Press the “AUTO” button to adjust the white balance automatically.
TEXT/PICTURE MODE
The Text enhancement feature provides the option to improve the readability of the text by improve the contrast of the text image via pressing the “T/P” button.
IMAGE FREEZE
The freeze function allows you to discretely prepare the next image without interrupting current presentation. Use "FREEZE" to freeze and unfreeze the image.
IMAGE MIRROR
The mirror function gives you a different perspective of an object.
SPLIT SCREEN
The split screen offers the capability of comparing two images or comparing two different views of one object side by side.
IMAGE SAVE
The PV 380 offers the opportunity of storing 12 images on board. You can recall them by just pressing one of the numerical buttons on the front panel or remote control.
IMAGE RECALL
By pressing the “
Recall
” button, all saved images is displayed in the thumbnail index mode for easy selection.
23
MULTIPLE INPUTS AND OUTPUTS
The VGA input allows a computer to be connected, inputting the computer signal. PV 380 also implements C-Video and S-Video connector, which can output the image from the document camera.
USB 2.0 PORT
The USB port can be used to store still images from the visualizer in a computer. No additional computer hardware is required. In this way, the visualizer can be used as a 3-D scanner for your computer. Connect the visualizer to your computer with the supplied USB cable. The Visualizer
Software is available on the supplied CD-ROM.
USB IMAGE CAPTURE AND VIDEO RECORDING
The PV 380 is the document camera equipped with a USB 2.0 image capture and video recording system. Simply connect the PV 380 to a computer, with the software and driver we provided, you can easily preview, capture and save any images on your PC and Mac.
RS232 CONTROL
The RS232 terminal allows you to integrate the PV 380 into any sophisticated central control system.
RS232 also enable you to control the PV 380 via computer.
8. SPECIFICATION
Model
Sensor
Pixels
Zoom
Frame rate
Shooting area
Focus
Output resolution
Resolution(Horizontal)
White balance
PV 380
1/3" CMOS
2 Megapixel
8x optical, 12x digital
15
Max: 13.5"x10.6", Min: 0.1"x0.1"
Auto/manual
XGA, SXGA
≥ 750 TV lines
Auto/manual
24
Color adjustment
Brightness adjustment
Image capture
Video recording
Image mirror
Image split
Image freeze
Text mode
OSD
Inputs
Outputs
USB2.0
RS232
Remote control
Light source
Kensington lock
Operating temperature
Dimensions
Power supply
Weight(net)
Yes
Yes
Yes,12 images
Yes(via USB)
Yes
Yes
Yes
Yes
Yes
VGA × 1, AUDIO × 1
VGA × 1, C-VIDEO × 1, S-VIDEO × 1, AUDIO × 1
Slave×1(USB camera) x1(computer controllable)
Yes(360°controllable)
LED light box
Yes
32°F ~113°F
Folded:12.6"×6.6"×3.7", Setup:19.7"×6.6"×19.3"
12V DC power adapter
5.5lbs/2.5kg
9. TROUBLE-SHOOTING:
Symptoms
No image
Image bending
Out of focus or blurring
Possible causes/counter-measures
1.
Power cord is not properly connected.
2.
Cables are not properly connected.
3.
Power switch is not turned on.
4.
Change the output resolution.
1.
Camera not in right position, adjust the camera.
2.
Distortion of LCD display, press the “Auto adjust” of the
LCD.
1.
The object is too close to the lens.
25
image 2.
Focus is on the top point of zoom, press ZOOM-.
3.
Auto-focus is not on: press AUTO again.
4.
Fog on the lens in damp climate. It will disappear gradually when the equipment warms up.
If the problem still remains after checking the above, consult your dealer or authorized service personally.
10. PACKING LIST
Item
Power cord
Power adaptor(12V/2A)
VGA cable
Switch cable(RCA to mini
)
USB cable(2.0)
Remote control
User manual(CD)
Quantity
1
1
1
1
1
1
1
26
11. TECHNICAL SUPPORT
Wanin USA is committed to providing highest possible stand of customer service. We can be reached:
By Phone
Call us at 1-877-369-3130. Our technical support staff provides technical assistance from 9:00AM through 5:00PM Pacific Standard Time, Monday through Friday. Please gather the following information before calling:
- Product model name(s) and numbers
- Product serial number(s)
- Detailed questions or problem descriptions.
Online
Technical support is also available online at Wanin USA’s web site at www.waninusa.com.
You can enter your questions and concerns through our online form, email us at [email protected].
Wanin USA Inc.
12961 Ramona Blvd., Irwindale, CA 91706
Toll Free: 1-877-369-3130 Fax: 626-609-3380
E-mail: [email protected] Web: www.waninusa.com
©2010 Wanin USA Inc. All Rights Reserved.
27
Advertisement
