MHS Boilers EF500 Installation Instructions Manual

Add to My manuals
20 Pages

advertisement

MHS Boilers EF500 Installation & Operation Manual | Manualzz
Electric Fireplace Heater
INSTALLATION INSTRUCTIONS AND HOMEOWNER’S MANUAL
MODEL EF500
39" ELECTRIC fireplace
®
C
US
IMPORTANT
WARNING
All electric fireplaces have hot and arcing or sparking parts inside. Do not store or use
gasoline or other flammable vapors and liquids in the vicinity of this or any other electric
fireplace.
WARNING
Read these instructions carefully before installing or trying to operate this electric fireplace.
This electric fireplace is tested and listed for use only with optional accessories listed in
these instructions. Do not use optional accessories not specifically tested for this electric
fireplace. Use of optional accessories may void warranty and result in a safety hazard.
READ AND SAVE THESE INSTRUCTIONS
CONTENTS
Important Safety Information........................... 2
Control Panel Operation ..............................11
Remote Control —Hand Held Transmitter
Operation..................................................... 12
Listing Approvals ............................................. 3
Product Specifications..................................... 4
Pre-Installation Information.............................. 4
Locating Electric fireplace.............................. 5
Unpacking and Testing Electric fireplace....... 6
Framing Electric fireplace.............................. 6
Framing Dimensions ..................................... 7
Electrical Connections .................................. 8
Electric fireplace Installation . ....................... 10
Operating Instructions ....................................11
Cleaning and Maintenance ............................ 13
Cleaning Electric fireplace Compartment . .. 13
Cleaning Back Glass . ................................. 14
Bulb Replacement . ..................................... 14
Blower and Electric fireplace Replacement 15
Troubleshooting ............................................. 16
Replacement Parts.......................................... 17
Warranty............................................Back Cover
IMPORTANT SAFETY INFORMATION
INSTALLER
Please leave these instructions with the owner.
OWNER
Please retain these instructions for future reference.
• Due to high temperatures, the electric fireplace should
be located out of traffic and away from furniture and
draperies.
• Never place any object on the electric fireplace.
• Never place clothing or other flammable material on
or near the electric fireplace.
• Electric fireplace becomes very hot when running.
Keep children and adults away from the hot surface of
electric fireplace to avoid burns or clothing ignition.
• Electric fireplace will remain hot for a time after
shutdown. Do not touch electric fireplace before it
cools.
• Carefully supervise young children when they are in
the room with the electric fireplace.
Take the following basic precautions when using electrical fireplaces to reduces the risk of fire, electric shock
and personal injury.
danger
Do not expose electric
fireplace to elements such
as rain, etc.
WARNINGS
WARNING
Improper installation or
use of the electric fireplace
can cause serious injury or
property damage. Use this
manual for reference. For
assistance or additional
information, consult a
qualified installer.
caution
IMPORTANT
Read these instructions carefully before installing or trying to operate this electric fireplace.
Never locate electric fireplace where it could
fall into a bathtub or other water container.
68D0018
IMPORTANT SAFETY INFORMATION
warning
RISK OF FIRE!
Do not block air intakes of electric
fireplace. Blocking air intakes can
cause a fire.
warning
Do not insert or allow foreign objects
to enter any ventilation or exhaust
opening of electric fireplace. This may
cause electric shock, fire, or damage to
electric fireplace.
warning
IMPORTANT SAFETY INFORMATION (continued)
Do not burn wood or other materials in
this electric fireplace. This could cause
a fire.
1.Keep combustible materials such as furniture, pillows,
bedding, papers, clothing, and curtains at least 3' from
front of electric fireplace. Also keep combustible materials
away from the sides and back of electric fireplace.
2. Always unplug electric fireplace when not in use.
3. Do not operate electric fireplace with a damaged cord or
plug.
4. Do not operate electric fireplace if electric fireplace malfunctions or has been dropped or damaged in any way.
5. Do not use electric fireplace outdoors.
6. Do not use electric fireplace in bathrooms, laundry areas,
or similar indoor locations.
7. Do not run power cord under carpeting or cover power
cord with throw rugs. Make sure power cord is away from
traffic area where it will not be tripped over.
8. Turn electric fireplace controls to “OFF” before removing
the plug from the outlet.
9. Use this electric fireplace only as described in this manual.
Using electric fireplace in any way not recommended
by the manufacturer may cause fire, electric shock or
personal injury.
10. Do not use an extension cord with electric fireplace. An
extension cord may overheat and cause a fire. If you must
use an extension cord, use a No. 14 AWG minimum size
cord that is rated not less than 1875 WATTS.
11. Always use properly grounded fused and polarized outlets.
12. Always use ground fault protection where required by
electrical codes.
13. Always unplug electric fireplace before performing any
cleaning or maintenance.
14. Always unplug electric fireplace before moving it.
15. Always use a certified electrician to install new circuits
or outlets.
16. Always keep electric fireplace free from excessive vibration when transporting electric fireplace.
17. Keep electric fireplace dry when transporting electric
fireplace.
18. Always store electric fireplace in dry place.
Listing Approvals
This electric fireplace has been tested in accordance with UL 2021 and CSA C22.2 No. 46 standards for a fixed location
dedicated electric room heaters.
Installation must conform to local codes. In absence of local codes, electrical wiring must comply with the latest edition of
the National Electrical Code ANSI/NFPA 70 in the USA. In Canada, comply with latest edition of the current CSA C22-1
Canadian Electrical Code.
68D0018
product specifications
electric fireplace dimensions
311/4"
LEFT
151/8"
TOP
211/8"
FRONT
33"
RIGHT
63/4"
36"
383/4"
ELECTRICAL
ACCESS
Figure 1 - Electric Fireplace Dimensions
68D0018
Pre-installation information
locating electric fireplace
Figure 2 - Electric Fireplace Locations
caution
Wear gloves and safety glasses for
protection during installation and
maintenance.
caution
Do not expose the electric fireplace to the
elements (such as rain, etc.)
caution
Never locate this electric fireplace where
it may fall into a bathtub or other water
container.
warning
Due to high temperatures, this electric
fireplace should be located out of traffic.
Keep combustible materials such as
furniture, pillows, bedding, papers,
clothes and curtains at least three (3)
feet (.9m) from the front of the electric
fireplace.
To prevent contact with sagging or
loose insulation, the electric fireplace
must not be installed against vapor
barrier or exposed insulation. Localized
overheating could occur and a fire could
result.
notice
warning
Figure 2 illustrates a variety of ways the electric fireplace may be located in a room. The electric fireplace may be installed
directly on the floor, carpet or raised on a hearth.
Minimum and maximum clearances must be maintained at all times. Illustrations throughout
these instructions show typical installations and are for design purposes only. Actual
installations may vary slightly due to individual preferences
68D0018
UNPACKING AND TESTING electric fireplace
caution
Carefully remove the electric fireplace from the box. Prior to permanently installing the electric fireplace, test to make sure
the electric fireplace operates properly.
Do not operate the electric fireplace if it is damaged
or has malfunctioned. If you suspect the electric
fireplace is damaged, return the electric fireplace
to an authorized service facility for examination,
electrical or mechanical adjustment or repair.
framing Electric fireplace
Electric fireplace framing can be built before or after the electric fireplace is set in place. Construct electric fireplace framing following Figure 3 and the chart below for your specific installation requirements. See Figure 1 on Page 4 for electric
fireplace dimensions. The framing headers may rest on the top of the electric fireplace standoffs.
The electric fireplace may be installed directly on a combustible floor or raised on a platform of an appropriate height. When
the electric fireplace is installed directly on carpeting, tile, or other combustible material, other than wood flooring, the electric
fireplace shall be installed on a metal or wood panel extending the full width and depth of the enclosure.
When framing with combustibe materials,all required clearances to combustibles must be adhered to. Header height is measured from the base of the electric fireplace.
Tools and building supplies required for installation:
•
•
•
•
•
•
•
Saw
Framing materials
Caulking Material
Tape measure
Phillips Screwdriver
Electric Drill/Bits
Wall-finishing Materials
•
•
•
•
•
•
Square
Pliers
Surround
Gloves
Hammer
Level
68D0018
warning
framing dimensions
EF500
Do not fill spaces around electric
fireplace with insulation or other
materials. This could cause a fire.
A Front Wall Opening
393/4"
B Framing Height
331/2"
C Back Width of Electric fire-
331/4"
D Width to Corner
165/8"
E
Corner Clearance Width
603/8"
F
Depth from Electric fireplace
301/4"
G Electric fireplace Framing
155/8"
H Corner Wall Length
423/4"
I
Electric fireplace Opening
Height
211/8"
J
Electric fireplace Opening
Width
36"
H
D
G
C
F
A
E
C
Corner Installation
G
A
Inside Chase Installation
C
B
I
G
Recessed Installation
Stud Location
Figure 4 - Framing Dimensions
68D0018
tabs will
accommodate
½" or 5/8"
finished
material
J
A
A
/2"Nailing
or 5/8"
1
1
/2" Nailing
or 5/8"
tabs will
accommodate
½" or 5/8"
finished
material
Pre-installation information
ELECTRICAL specifications
Power Requirements
SIP2
SIP3
1.
2.
3.
4.
5.
Rated Wattage
Amperage
120 Volt, 60 Hz.
1500 Watts
13.33 Amps
240 Volt, 60 Hz
3000 Watts
13.33 Amps
ELECTRICAL CONNECTIONS
Control Panel
IR
Flame Switch
Heater Switch
Set Temp LED (3-Color)
Power LED (Green
Wire a dedicated, properly fused circuit
with a 20 Amp rating for the appropriate
voltage (120V or 240 V). Preferably, the
electric fireplace will be on a dedicated
circuit, as other electric fireplaces on
the same circuit may cause the circuit
breaker to trip, or the fuse to blow, when
the electric fireplace is in operation. See
Figures 5 through 7.
M
N1
Motor
H2
H1+Fan
Heater
Heater
Heater
Heater
L2
N2
F
P-L
Fuse
WARNING
Temp
Temp
Switch
Fuse
Electrical wiring must
comply with local building
codes and other applicable
regulations to reduce risk
of fire, electrical shock and
injury to individuals.
L1
Lamp
Fire
L
L
NO
NI
From Fireplace
Figure 5 - Wiring Diagram
N
N
L
G
Junction Box
G
Junction Box
N
N
N1
N1
N2
N2
L1
L1
L1
L2
L2
L2
G
G
Figure 6 - Wiring
Connection for 120
Volts, 1500 Watts
WARNING
N
Control Board
Junction Box
Any electrical rewiring of
this electric fireplace must
be done by a qualified
electrician.
WARNING
Do not use this electric
fireplace if any part of it
h a s b e e n u n d e r w a t e r.
Immediately call a qualified
service technician to inspect
electric fireplace. Replace
any part of the electrical
system which has been
under water.
G
Figure 7 - Wiring
Connection for 240
Volts, 3000 Watts
68D0018
electric fireplace installation
WARNING
RISK OF FIRE! The power cord must
not be pinched or against a sharp edge.
Secure cord to avoid tripping or snagging
to reduce the risk of fire, electric shock
or personal injury. Do not run cord under
carpeting. Do not cover cord with throw
rugs, runners or the like. Arrange cord
away from traffic areas where it will not
be tripped over.
warning
PACKAGING LIST
RISK OF FIRE! Do not blow
or place insulation against
the electric fireplace.
This assembled electric fireplace is packaged with:
One accessory package located in the electric
fireplace, containing:
QTY
1
2
1
Installation and Operation Manual
Light Bulbs
One Remote Control
warning
RISK OF FIRE! To prevent a possible
fire, do not block air intake or exhaust
in any manner. Do not use on soft
surfaces (like a bed) where openings
may become blocked.
WARNING
If any part or parts are missing or damaged, contact dealer
where you bought electric fireplace.
This electric fireplace is tested and listed for use only with the approved optional accessories.
Use of optional accessories not specifically tested for this electric fireplace could void the
electric fireplace warranty and/or result in a safety hazard.
installation instructions
1. Complete the framing opening to the dimensions specified in Figure 4, page 7.
2. Make sure there is a minimum of 8" of service cable for connection to the junction box on the electric fireplace. Remove
outer jacket and strip the individual wires 1/2" from the end.
3. Loosen the screw securing the junction box cover. Remove the cover.
4. Position electric fireplace into the framed in opening. Attach electric fireplace to frame using nailing flanges provided.
5. Complete the wiring to the electric fireplace for the appropriate voltage (120 V or 240 V), as shown on page 8. Wires
L1, L2, N & G are attached to the rear of the junction box cable clamp for easy access.
6. Wire a dedicated, properly fused circuit with a 20 Amp rating for the appropriate voltage (120 V or 240 V).
7. Place all connectors inside the electric fireplace and replace the junction box cover. Make sure the cable clamp grips only
the jacket of service, and if applicable wall switch lines.
8. Perform a function test. See Control Panel Operation on page 11 and Remote Control Operation on page 12.
68D0018
electric fireplace installation
FINISHING
Combustible Finishing Material: Materials are made of wood or surfaced with wood, compressed paper, plant fibers,
plastics or any material capable of igniting and burning, whether flame-proofed or not, plastered or unplastered (this includes
drywall).
warning
Noncombustible Finishing Material: Materials will not ignite and burn. Such materials are those consisting entirely of
steel, iron, brick, tile, concrete, slate, glass or plasters or combinations thereof or have a fire rating of zero.
Grilles on this electric fireplace
cannot, in any way, be covered.
This may create a fire hazard.
FINISHING CHECKLIST
•
Power supply service must be completed prior to finishing to avoid reconstruction.
•
Grilles and air openings cannot be covered in any circumstances.
NOTE: The electric fireplace is a zero clearance electric fireplace and may be finished with combustible
or noncombustible finishing materials.
Paint or lacquer used to finish the mantel must be heat resistant to prevent discoloration.
10
68D0018
operating instructions
location of controls
This electric electric fireplace can be operated either from the control panel or by using the hand held transmitter. The control
panel is located on the upper right side compartment. The hand held transmitter comes with the electric electric fireplace.
Set Temp LED
On/Off Switch
IR Receiver
Power LED
FL
ON
TEMP
Flame Adjust Button
OFF
Set Temperature Adjust Button
Figure 8 - Control Panel
Control Panel Operation
ON /OFF Switch (See Figure 8)
On/Off switch will turn electric electric fireplace on or off.
1. When the switch is turned to “I” / “ON” position (Power LED will turn to green color)…
a. Flame defaults to high setting
b. Ember bed defaults to low setting.
c. Electric fireplace defaults to OFF position (Temp LED will be off).
2. When the switch is turned to “O” / “OFF” position (Power LED will be off)…
a. Flame will be off
b. Ember bed will be off
c. Electric fireplace will be off (Temp LED will be off)
Note: Electric fireplace may release a slight, harmless odor the first time it is used. This odor is a
normal. It is caused by the initial heating of the internal heating elements and will not occur again.
FL – Flame Adjustment Button (See Figure 8)
1. There are a total of 4 settings (Off, Low, Medium, and High) to adjust the flame and light ember bed.
NOTE: Flame and ember bed setting cannot be adjusted independently from this switch.
2.Press button to cycle through lighting. Note that the Power LED light is always green.
TEMP – Set Temperature for Electric fireplace Button (See Figure 8)
1. The electric fireplace has a built-in thermostat so it will shut off automatically once the set temperature is reached. It will
also turn on automatically if the room temperature drops below the set temperature.
2. The electric fireplace is pre-set to the following temperatures:
• HI will shut off when room reaches approximately 86° F (30 C). The LED is red.
• MED will shut off when room reaches approximately 75° F (24 C). The LED is orange.
• LO will shut off when room reaches approximately 64°F (18 C). The LED is green.
3. Press TEMP Button to cycle through settings. When this button is pressed the set Temp LED light setting will change to
its corresponding color. See step 2.
68D0018
11
electric fireplace installation
Remote Control – Hand Held Transmitter Operation
The hand held transmitter is provided with the electric fireplace. All functions of the electric fireplace can be controlled from
this hand held transmitter.
Note: The effective range of the remote control is up to approximately 26 feet (8 meters).
Point hand held transmitter at the IR receiver on the control panel to operate. Make sure your batteries are fully charged
and installed correctly in your hand held transmitter. When there is a transmission or signal being sent, the front of the hand
held transmitter will flash.
To control the electric fireplace, the On/Off switch of the control panel must be ON. See Control Panel Operation, page
11.
ON /OFF Button
Used to turn on or off the electric fireplace using the hand held
transmitter.
Ember Bed
Adjustment
Button
On/Off
Button
FLAME – Flame Adjustment Button
1. There are a total of 8 settings (Off to Highest) to adjust the flame
lighting. See Figure 9.
2. Used to increase or decrease flame, press the “+” or “-” buttons to
cycle through the lighting. See Figure 9.
LIGHT
Flame
Adjustment
Button
FLAME
ON/OFF
TEMP.
Set
Temperature
LIGHT – Ember Bed Adjustment Button
1. Used to adjust the ember bed lighting. There are a total of 8 settings
(Off to Highest) to adjust the ember bed lighting. See Figure 9.
2. Used to increase or decrease flame, press the “+” or “-” buttons to
cycle through the lighting. See Figure 9.
Figure 9 - Remote Control
TEMP – Set Temperature for Electric fireplace Button
1. The electric fireplace has a built-in thermostat. This shuts the electric fireplace off automatically once the set temperature
is reached, The electric fireplace will also turn on automatically if the room temperature drops below the set temperature.
2. The electric electric fireplace is pre-set to the following temperatures:
•
HIGH will shut off when room reaches approximately 86° F (30 C). The LED will be red.
•
MEDIUM will shut off when room reaches approximately 75° F (24 C). The LED will be orange.
•
LOW will shut off when room reaches approximately 64°F (18 C). The LED will be green.
3. Press TEMP Button to cycle through settings. When this button is pushed, the set Temp LED light setting will change
to its corresponding color on the control panel.
12
68D0018
WARNING
cleaning and maintenance
Always disconnect power and allow the electric fireplace to cool before performing any
cleaning, maintenance or relocation of this electric fireplace. Turn controls to OFF and
remove plug from outlet or turn off circuit breaker to electric fireplace.
Turn off electric fireplace and circuit breaker to electric fireplace before performing any cleaning and/or maintenance. Allow
electric fireplace to cool completely.
CLEANING Electric fireplace COMPARTMENT
1. Using vacuum with brush attachment, gently clean compartment.
2. After cleaning compartment, replace front face and reset circuit breaker.
BACK GLASS
1. The glass is cleaned in the factory during assembly. During shipment, installation, handling, etc. the glass surface may
collect dust particles. Remove dust particles by buffing lightly with a clean dry cloth.
2. Do not use any type of cleaner or water to clean off glass surface. This may disfigure the brick pattern. Gently rub glass
surface with a soft. dry cloth to remove dirt
3. If glass breaks, vacuum all remaining glass pieces with a shop vac. DO NOT VACUUM WHILE PIECES ARE HOT.
Replace glass only with replacement part specifically for this electric fireplace. Never substitute material. Only fully
tempered soda lime safety glass may be used on this electric fireplace.
warning
BULB REPLACEMENT
The halogen light bulbs in your electric fireplace
can become extremely hot. Allow at least 10
minutes between turning off the electric fireplace
and removing the light bulbs to avoid accidental
burns.
There are a total of 5 halogen light bulbs (type GX6.35 rated 120 volts, 35 watts) in your electric fireplace.
•
3 bulbs provide illumination nation for the flame generation assembly
Do not install replacement
bulbs that exceed specified
maximum watts.
warning
2 bulbs provide illumination for the ember bed beneath the log set
warning
•
Always wear gloves and eye
protection when handling and
replacing glass bulbs in case
bulb is accidentally broken.
If the electric fireplace has been running, turn off power and let electric fireplace cool before changing bulb.
68D0018
13
cleaning and maintenance
Ember Bed Bulbs
1. Follow Step 1 under Cleaning Electric Fireplace Compartment, page 13 to remove grate assembly with logs.
2. Gently pull forward and lift up grate assembly with logs until front edge clears the electric electric fireplace.
NOTE: Do not pull up on logs.
3. Remove spring clip. Hold socket and
pull out old bulb. See Figure 10.
Bulbs
4. Hold socket and push in new bulb
(DO NOT exceed wattage).
5. Repeat steps 3 and 4 with second
bulb. (Springs are used to secure
the bulb during transportation.)
6. Reinstall grate assembly and logs.
Spring Clips
7. Reinstall front bottom face.
Figure 10 - Ember Bulb Location
Flame Generation Bulbs
Bracket
Glass
Glass
Remove
Screws
1. Remove screws from glass holder brackets. The brackets
are located on the inside of the electric fireplace. The
screws to be removed are on the inside. See Figure 11.
2. Wearing gloves, lift up on bottom of glass and pull
forward. Place glass on smooth, soft surface to avoid
breakage.
3. Locate flame generation cylindrical drum. See Figure
12.
4. Squeeze half of drum cylinder until it’s top edge clears
the top drum track. Remove bottom edge of cylinder
drum from bottom drum track. This will give you access
to the light bulbs.
NOTE: Do not exert excessive pressure on drum
cylinder as this may cause damage.
Figure 11 - Glass and Bracket Location
Flame Cylinder Drum
5. Remove spring clip. Hold socket and pull out old bulb.
6. Hold socket and push in new bulb. DO NOT exceed wattage.
7. Repeat steps 5 and 6 for second and third bulbs. Reconnect spring.
8. Insert bottom edge of removed cylinder half into bottom drum track.
Squeeze drum cylinder until its top edge fits into top drum rack.
9. With gloves, carefully reinstall glass.
10. Install glass holder brackets with screw s removed in step 2.
14
Figure 12 - Flame Generation
Cylinder Drum
68D0018
blower and electric fireplace replacement
1. Remove the six (6) screws securing inner top panel from the inside of the electric fireplace.
2. Remove the four (4) screws securing heater/blower assembly.
3. Remove the two (2) screws securing panel top from the front of the fireplace.
4. Pull handle located on the blower/heater assembly to slide blower assembly forward.
5. Disconnect wiring. Mark or label wiring so you will hook it up correctly when reinstalling.
6. Replace blower/heater assembly. Install all components that you removed earlier.
Wire
Connection
Blower
Assembly
Top Panel
Figure 13 - Replacing Blower
68D0018
15
troubleshooting
OBSERVED PROBLEM
POSSIBLE CAUSE
REMEDY
Electric fireplace turns off
and will not turn on.
Electric fireplace has overheated.
The electric fireplace is protected with a safety
device to prevent it from overheating. If the electric
fireplace should overheat, a thermal switch will
disconnect power to the electric fireplace and will
not come back on without being reset. Reset electric
fireplace by turning the main power switch off and
waiting 5 minutes then turning it back on.
Flame is fixed (unmoving).
Wiring may be loose or the flame motor
may be defective.
Inspect all wiring for loose connections. Repair or
replace if necessary. If the wire connections are
good, replace the flame motor.
Dim or poorly visible flame.
Log set and ember not glowing.
Light bulb(s) burnt out or wiring is loose.
Inspect all wiring for loose connections and repair or
replace if necessary. Inspect light bulbs and replace
if necessary.
Flame sputters.
Flame motor is defective.
Replace flame motor.
Remote control does not
work.
Low batteries.
Replace AA batteries in remote control. If problem
persists, there may have been a loss of power to the
electric fireplace as a possible result from a power
failure (i.e. breaker tripped or the main power switch
has been turned off).
Electric fireplace turns on or Remote control has a similar frequency to
off by itself.
other remotes in the house.
Exchange the other remote controls in home for one
with a different frequency.
Circuit breaker trips or
fuse blows when the electric
fireplace is turned on.
Have a qualified electrician check the house circuit
to ensure it is on a dedicated circuit with a 35-amp
rating. If the circuit breaker continues to trip (or
blow fuses), inspect wiring for a loose connection or
a dead short. Repair or replace wiring and/or connectors as necessary.
16
Improper circuit current rating.
68D0018
replacement parts
Item Description
Qty
Part No.
Standard Features
1
Electric fireplace Assembly
1
68D0101
2
Motor (Rear Flame)
1
68D0102
3
Glass (Including Gasket)
1
68D0103
4
Hand Held Transmitter
1
68D0104
5
PCB Main Control
1
68D0105
6
PCB Control Panel
1
68D0106
7
Light Bulb ****
5
68D0107
8
On/Off Switch
1
68D0108
9
Pull Screen
2
68D0109
10
Ember Bed
1
68D0110
11
Logs Assembly
1
68D0111
**** Equivalent bulbs can be purchased at Electrical Supply Stores, Home Improvement Stores, etc. Use only light bulbs
that are rated as follows: TYPE GX 6.35, 120 VOLT, 35 WATT MAXIMUM
68D0018
17
replacement parts
Description
Qty
Part No.
1
EFCORD
Black Medium Trim Kit
1
BLE500TK
Pewter Medium Trim Kit
1
PWE500TK
Brass Medium Trim Kit
1
BRE500TK
Accessories/Field Installed Options (Not Shown)
Electrical
3 Prong 120V Plug-In (3.5 feet)
Metal Trim Kit
Glass Door
Black Finish Single-Pane Glass Door
1
GDS36BA
Brass Finish Single-Pane Glass Door
1
GDS36PBA
Stainless Finish Single-Pane Glass Door
1
GDS36SSA
Black Finish Bifold Glass Door
1
GD36BA
Brass Finish Bifold Glass Door
1
GD36PBA
Stainless Finish Bifold Glass Door
1
GD36SSA
Facing
Arch Front
Arched Front with Lower Control Door, Black
1
VB36AFB/36VBFB
Arched Front with Lower Control Door, Gold
1
VB36AFG/36VBFG
Arched Front with Lower Control Door, Brushed Pewter
1
VB36AFP/36VBFP
Cabinet Door Frame, Black
1
VC36CDFB
Cabinet Door Frame, Gold
1
VC36CDFG
Cabinet Door Frame, Brushed Pewter
1
VC36CDFP
Cabinet Door Frame
Cabinet Doors with Screen, Requires purchase of Cabinet Door Frame
Cabinet Doors with Screen, Black
1
V36CDB
Cabinet Doors with Screen, Gold
1
V36CDG
Cabinet Doors with Screen, Brushed Pewter
1
V36CDP
18
68D0018
notes
Description
Qty
Part No.
Oak Surround with Honey Oak Finish
1
WSGC36F-O
Birch Surround with Dark Cherry Finish
1
WSGC36F-DC
Oak Surround Unfinished
1
WSGC36U-O
Birch Surround Unfinished
1
WSGC36U-B
Oak Hearth with Honey Oak Finish
1
WHGC36F-O
Birch Hearth with Dark Cherry Finish
1
WHGC36F-DC
Oak Hearth Unfinished
1
WHGC36U-O
Birch Hearth Unfinished
1
WHGC36U-B
Oak Corner Surround with Honey Oak Finish
1
CSGC36F-O
Birch Corner Surround with Dark Cherry Finish
1
CSGC36F-DC
Oak Hearth Surround Unfinished
1
CSGC36U-O
Birch Hearth Surround Unfinished
1
CSGC36U-B
Oak Corner Hearth with Honey Oak Finish
1
CHGC36F-O
Birch Corner Hearth with Dark Cherry Finish
1
CHGC36F-DC
Oak Hearth Corner Surround Unfinished
1
CHGC36U-O
Birch Hearth Corner Surround Unfinished
1
CHGC36U-B
Wall Cabinet Riser - Unfinished Oak **
1
WCRU
Wall Cabinet Riser - Honey Oak **
1
WCRHO
Wall Cabinet Riser - Cherry **
1
WCRC
Wood Products
Wall Surround
Wall Hearth
Corner Surrounds
Corner Hearth
Wall Cabinet Riser
** If installing an Arched Front with a Wood Cabinet, a Wall Cabinet Riser must be installed also.
68D0018
19
MHS
Warranty Policy
BASIC WARRANTY
MHS warrants the components and materials in your electric fireplace to be free from manufacturing and material
defects for a period of one year from date of installation. After installation, if any of the components manufactured
by MHS in the electric fireplace are found to be defective in materials or workmanship, MHS will, at its option,
replace or repair the defective components at no charge to the original owner. MHS will also pay for reasonable labor
costs incurred in replacing or repairing such components for a period of one year from the date of installation.
Any products presented for warranty repair must be accompanied by a dated proof of purchase.
This Warranty will be void if the electric fireplace is not installed by a qualified installer in accordance with the
installation instructions. The Warranty will also be void if the electric fireplace is not operated and maintained
according to the operating instructions supplied with the electric fireplace, and does not extend to (1) damage by
accident, neglect, misuse, abuse, alteration, negligence of others, including the installation thereof by unqualified
installers, (2) the costs of removal, reinstallation or transportation of defective parts on the electric fireplace, or
(3) incidental or consequential damage. All service work must be performed by an authorized service representative.
This warranty is expressly in lieu of other warranties, express or implied, including the warranty of merchantability
of fitness for purpose and of all other obligations or liabilities. MHS, Inc. does not assume for it any other obligations or liability in connection with the sale or use of the electric fireplace. In states that do not allow limitations on
how long an implied warranty lasts, or do not allow exclusion of indirect damage, those limitations of exclusions
may not apply to you. You may also have additional rights not covered in this Warranty.
MHS reserves the right to investigate any and all claims against the Warranty and decide upon method of settlement.
For information about this warranty, contact:
Technical Services
MHS
149 Cleveland Drive
Paris, Kentucky 40361
July 2005
P/N 68D0018 • Rev. 2

advertisement

Key Features

  • 39-inch electric fireplace
  • Realistic flame & ember bed
  • Thermostat
  • Timer
  • Remote control

Related manuals

Frequently Answers and Questions

How do I set the temperature?
You can use the control panel or remote control to cycle through the HI, MED, and LO settings.
Can I adjust the flame intensity?
Yes, the FL button on the control panel or remote control allows you to cycle through 4 flame settings.
What are the clearance requirements for this electric fireplace?
Combustible materials need a minimum clearance of 3 feet from the front of the fireplace and from the sides and back.
Download PDF

advertisement