LASER Volkswagen Audi Group 1.2 FSI/TFSI | 1.4 | 1.6 FSI | 1.4 TSI Engine Timing Tools Instructions

www.lasertools.co.uk
gh
t
ri
ht
ig
C
op
yr
ht
ig
ht
ht
C
op
ig
se
r
C
op
C
op
C
yr
i
er
yr
ig
ht
La
s
ig
C
op
y
ht
La
s
er
La
s
er
La
s
er
La
s
e
La
s
ht
ig
op
yr
ig
ig
op
yr
Volkswagen Audi Group 1.2 FSI/TFSI | 1.4 | 1.6 FSI | 1.4 TSI
Part No. 4419
py
er
C
op
yr
C
op
yr
C
op
yr
C
se
r
La
C
op
yr
La
se
r
C
La
t
gh
se
r
La
se
r
La
se
r
La
se
r
La
se
r
La
gh
t
ri
ht
ht
ri
g
ht
op
yr
ig
ri
gh
t
op
y
C
C
op
y
se
r
yr
ig
op
C
se
r
www.lasertools.co.uk
Engine Timing Tools
Part No. 5742
La
s
e
C
r
se
La
r
ig
op
ht
r
s
y
e
C
r
La
r
ig
op
C
h
s
yr
op
t
e
C
La
r
ig
op
y
C
ht
se
yr
op
La
r
ig
y
C
r
ht
se
i
o
g
ri
p
h
La
r
gh
yr
t
C
se
ig
op
t
h
La
r
yr
t
C
se
La
ig
op
ht
La
r
s
y
C
r
se
La
ig
op
ht
r
s
y
e
C
r
La
r
ig
op
er
C
h
s
yr
t
e
C
La
r
ig
op
C
h
s
yr
op
t
e
La
r
ig
y
C
py
r
ht
se
i
o
ri
p
L
r
gh
yr
as
C
ig
op
t
e
Introduction
Warning
Incorrect or out of phase engine timing can result in damage to the valves.
The Tool Connection cannot be held responsible for any damage caused by
using these tools in anyway.
gh
t
Safety Precautions – Please read
• Remove spark or glow plugs to make the
engine turn easier
• Observe all tightening torques
• Do not use cleaning fluids on belts,
sprockets or rollers
• Always refer to the vehicle manufacturer’s service manual or a suitable proprietary instruction book
• Always make a note of the route of the
auxiliary drive belt before removal
• Incorrect or out of phase engine timing can result in damage to the valves
• Turn the engine in the normal direction
(clockwise unless stated otherwise)
• It is always recommended to turn the engine slowly, by hand, and to re-check the camshaft and crankshaft timing positions
op
y
• Do not use the timing chain to lock the
engine when slackening or tightening
crankshaft pulley bolts
Additional tools increase the application of this set to include:
1.2 litre with engine codes: CBZA, CBZB, CBZC
se
r
• Check the diesel injection pump timing
after replacing the chain
• Do not turn the camshaft, crankshaft or
diesel injection pump once the timing
chain has been removed (unless
specifically stated)
Part No. 5742
Engine Service Tool Kit
Volkswagen Audi Group 1.2 FSI/TFSI | 1.4 | 1.6 FSI | 1.4 TSI
1.4/1.6 litre with engine codes: BAG, BLF, BLG, BLP, BMY, BWK CAXA (03-) in
Golf Estate, Golf Plus, Jetta, Passat, Eos, Tiguan and Touran
• Do not turn the crankshaft or camshaft
when the timing belt/chain has been
removed
• Mark the direction of the chain before
removing
• It is always recommended to turn the
engine slowly, by hand and to re-check
the camshaft and crankshaft timing
positions.
• Crankshafts and Camshafts may only be
turned with the chain drive mechanism
fully installed.
• Do not turn crankshaft via camshaft or
other gears
www.eldontools.co.uk
www.lasertools.co.uk
2
• Disconnect the battery earth leads (check
radio code is available)
www.lasertools.co.uk
7
La
s
e
C
r
se
La
r
ig
op
ht
r
s
y
e
C
r
La
r
ig
op
C
h
s
yr
op
t
e
C
La
r
ig
op
y
C
ht
se
yr
op
La
r
ig
y
C
r
ht
se
i
o
g
ri
p
h
La
r
gh
yr
t
C
se
ig
op
t
h
La
r
yr
t
C
se
La
ig
op
ht
La
r
s
y
C
r
se
La
ig
op
ht
r
s
y
e
C
r
La
r
ig
op
er
C
h
s
yr
t
e
C
La
r
ig
op
C
h
s
yr
op
t
e
La
r
ig
y
C
py
r
ht
se
i
o
ri
p
L
r
gh
yr
as
C
ig
op
t
e
Instruction
Plan Layout
Follow all general precautionary preparation
work, and then if removing the timing chain it
is necessary to remove the timing chain cover
and sump.
A
Camshaft Locking Tool
gh
t
Component A is the camshaft locking tool
used on the 1.2 FSi engines (CBZA and
CBZB).
Many performance engines have an
interference combustion area, which if the
correct timing position is not achieved could
result in serious damage to the valves and
other parts of the engine.
D
C
G
Camshaft Alignment Tool
If the Camshaft Timing Marks are not
correctly aligned with the engine set at TDC,
turn the Crankshaft 360° and check the
Camshaft timing mark again. Fit the
Camshaft Alignment Tool.
E
E
F
If the Camshaft Alignment tool can still not
be fitted the valve timing is incorrect.
A - C574
B
D
Camshaft Tensioner Pin
Fit the tensioner locking pin to hold the
chain tensioner back, allowing the removal
of the camshaft sprockets and chain.
A
op
y
Set the camshaft positions and align using
the Camshaft Alignment Tool.
To gain access to the grooved end of the
camshaft remove the hose connecting block
from the rear of the cylinder head (gearbox
end).
Fit C574 as shown. Ensure fixing bolt can be
fitted.
B
se
r
Crankshaft Locking Pin
Use the Crankshaft Locking tool when
loosening and tightening the crank.
G
Guide Pins (2)
The two guide pins hold the supercharger
in the correct position during installation.
Dial Test Indicator
Top Dead Centre (TDC) measurement must
be checked, this set includes TDC Adaptor
(used in conjunction with a Dial Test Indicator)
which enables the accurate measurement of
the piston position.
C
F
TDC Indicator
The Indicator is fitted into the first cylinder
spark plug hole. The extension makes contact
with the piston face and as the engine is
slowly rotated the DTI indicates the TDC, or
the highest point required.
Re-install the sprockets and chain and
correctly tighten the sprockets.
It is advised to use new crankshaft pulley
and camshaft sprocket bolts.
Remove the Camshaft Alignment Tool and
turn the Crankshaft twice in a clockwise
direction.
Check the valve timing again.
www.lasertools.co.uk
6
Code
Oem Code
Description
A
C574
T10414
Camshaft Locking Tool
B
C127
VAS 6079
Dial Test Indicator 41 x 8mm
C
C226
T10170
TDC Indicator
D
C345
T10171/T10171A
Camshaft Alignment Tool
E
C284
T40011
Camshaft Tensioner Pin
F
C439
T10340
Crankshaft Locking Pin
G
C440
T10341
Guide Pins (2)
www.lasertools.co.uk
3
La
s
e
C
r
se
La
r
ig
op
ht
r
s
y
e
C
r
La
r
ig
op
C
h
s
yr
op
t
e
C
La
r
ig
op
y
C
ht
se
yr
op
La
r
ig
y
C
r
ht
se
i
o
g
ri
p
h
La
r
gh
yr
t
C
se
ig
op
t
h
La
r
yr
t
C
se
La
ig
op
ht
La
r
s
y
C
r
se
La
ig
op
ht
r
s
y
e
C
r
La
r
ig
op
er
C
h
s
yr
t
e
C
La
r
ig
op
C
h
s
yr
op
t
e
La
r
ig
y
C
py
r
ht
se
i
o
ri
p
L
r
gh
yr
as
C
ig
op
t
e
Applications
The application list for this product has been compiled cross referencing the OEM Tool Code
with the Component Code.
The application list for this product has been compiled cross referencing the OEM Tool Code
with the Component Code.
In most cases the tools are specific to this type of engine and are necessary for Cam belt or
chain maintenance.
In most cases the tools are specific to this type of engine and are necessary for Cam belt or
chain maintenance.
If the engine has been identified as an interference engine valve to piston damage will occur if
the engine is run with a broken Cam belt.
If the engine has been identified as an interference engine valve to piston damage will occur if
the engine is run with a broken Cam belt.
A compression check of all cylinders should be performed before removing the cylinder head.
A compression check of all cylinders should be performed before removing the cylinder head.
Always consult a suitable work shop manual before attempting to change the Cam belt or
Chain.
Always consult a suitable work shop manual before attempting to change the Cam belt or
Chain.
gh
t
Applications
Autodata
Our applications data is supplied by Autodata and we are able to supply this data to you in a
PDF format.
If this is a specific kit for a group of engine codes the application list has been supplied
showing the main vehicles this kit is designed for and does not list every model each pin fits.
If this is a master kit then all vehicles are included.
The data is the copyright of The Tool Connection Ltd and should not be reproduced
op
y
If the application data is extensive we have included a CD with the application list in .pdf
format.
Languages
We have also included where possible translations for the instructions in the following
languages:
•
•
•
•
•
•
French
Spanish
Italian
Dutch
German
Portuguese
se
r
The use of these engine timing tools is purely down to the user’s discretion and
The Tool Connection cannot be held responsible for any damage caused what so ever.
ALWAYS USE A REPUTABLE WORKSHOP MANUAL
For up to date information go to:
www.lasertools.co.uk/toolpoint
www.lasertools.co.uk
4
www.lasertools.co.uk
5