Trusted Clean TPL-17-200-CE-HEAT-TCP Owner's Manual
Trusted Clean TPL-17-200-CE-HEAT-TCP is a commercial carpet, floor, and upholstery extractor designed for professional cleaning applications. It features a powerful 120/220V motor that delivers 500 PSI of pressure and 200°F of heat for effective cleaning and sanitization. The machine includes a 10-gallon solution tank and a 10-gallon recovery tank, allowing for extended cleaning sessions without the need for frequent refilling or emptying.
PDF
Download
Document
Advertisement
Advertisement
GALAXY OWNER’S MANUAL & PARTS LIST This equipment is intended for commercial use only. TPL-17-200-CE-HEAT-TCP BEFORE OPERATING THE MACHINE Read the manual carefully and completely before attempting to operate the unit. This manual has important information for the use and safe operation of the machine. Keep this manual handy at all times. This machine will assure years of satisfactory service if operated and maintained according to recommendations in this manual. If additional information is needed, please contact your local distributor or write to: CleanFreak P.O. Box 569 Wausau, WI 54402 WARNING • • • • • • • • • • • • • • The machine was designed for use on carpet, floor and upholstery extraction applications as per instructions and recommendations written in this manual. Any deviation from its proper use or purpose and the consequential damage that may occur is the sole responsibility if the end user. Disconnect the power cord from the outlet before servicing. Do not leave machine connected to an electrical outlet when unattended. Do not immerse or use this machine in standing water. Such use may cause electric shock. This equipment is not designed to handle or use combustible/volatile substances such as gasoline or kerosene, in, on, or near the machine. The use of such materials will cause extreme hazardous condition. When using an extension cord, use only a 3-prong conductor grounding cord, 12 gauge wire or heavier. To avoid electric shock, do not expose the unit to rain. Store it indoors only. Do not use the machine for dry vacuuming. Use defoamer at all times to prevent damage to the vacuum motor(s). Do not use water in excess of 170ºF (76ºC). To prevent seal damage and chemical build-up to the pump system, run clean water through the solution lines after each day’s use. Use only commercially available carpet cleaning solutions and defoamer intended for use with machines of this type. Do not use dyes, bleaches, ammonia, or other additives. The use of powdered cleaning solution if not diluted properly may result in damage to the pump. If powdered chemicals are used, premix in a separate container before placing in the solution tank. Do not expose machine to freezing temperatures. All repairs must be done by an authorized CleanFreak repair station. Do not use replacement parts other than those specified on the parts list. For units with HEAT’N’RUN heater: • Read and understand the HEAT’N’RUN owners manual before using the HEAT’N’RUN heater on your GALAXY Extractor. • Do not run heater dry. • Water hookups must be in place and water flowing through the heater prior to turning it on. Failure to do so may cause internal component damage and will void warranty. • Heater must be filled with water or water based solutions at all times when in use. Turn off the switch and unplug the heater from outlet when not in use. • Do not use heater with any other machine and at any pressure higher than 250 PSI. • Do not immerse heater in water. • To avoid explosion and / or fire, do not use solvents or any flammable liquid in heater. FAILURE TO COMPLY WITH THE ABOVE WARNING INSTRUCTIONS WILL VOID THE WARRANTY 2000FX-HR Base The 120V A/C and the 220V A/C models have been outfitted with the appropriate 12-19-07 grounded connectors. Make sure the machine is connected to a grounded outlet GROUNDING INSTRUCTIONS ITEM the same configuration asPART having the grounded NUMBER plug. No adapter should be used with DESCRIPTION NO. this Any modification 1 machine. C00297 #8 X .25 Pan Head to the connectors will void the warranty. QTY. 1 2 J11863 Hose, 3 in 1 3 J00639 Screw Clamp, 1.63 - 2.43in. 3 PREPARING THEHose, MACHINE GALAXY EQUIPMENT) 4 J00618 Vacuum 2in Grey,(ALL Wire, 22 in lg 1 5 C00273 Locknut, 1-4 X 20, Nylon, SS 16 6 F11178-BLK Intercooler, Galaxy, Black use only the correct high pressure, high heat wands & uphol- 1 IMPORTANT: For all Galaxy equipment, 7 C00233 Washer, Flat, .25 in 26 stery tools. They are designed to deliver and maintain the correct gallons per minute (GPM), pressure (PSI) 8 E00449 Grommet 6 9 C00284 Screw, 10-32 X .375 Ground 2 and when attached the GALAXY pump system. Use of other manufacturer wands can cause over10 heat B11150 Ground Wire, to Galaxy 2 11 G02522L Vacuum , 135 to in, the 115 pump V, 5.7 insystem (including hose & fittings), lack of pressure and heat. 2 wetting of carpet, damage 12 J00657 Hose Clamp, 2 inSLDPRT 1 1 13 J00618 Vacuum Hose, 2 in Grey, Wire, 4 in lg 1.14Pour clean solution C00261 Nut, .25-20, into Hex the solution tank. 10 C00254 Lock hose Washer, 1-4in 2.15Slide vacuum onto theSplit black hose adapter (located at the back of the machine) and the wand or1 16 D11134 Vac Plate 1 tool. 1-4 X 20 X 4.5 in, Hex 17upholstery C11189 Screw, 5 18Connect C02312 the Lockwasher, Starhose to the wand and the female end to the machine by sliding 1 3.19 male end.25ofin., theInternal solution C11516 Screw, 1-4 X 20 X 4.5 in, Flat Head, Phillips 1 onHose, the female quickWire, disconnect J11154collar Solution .375, 100PSI, 31 in lg fitting back. Push the male fitting in and release the knurled 1 20knurled 21collar J11508 Screw Clamp #6, .43 to .875 in 8 until it snaps back. 22 G11904 Power Prime 1 4.23Make sure drain valve is closed A00060 .25the Male X .375 Barb, Brass by pushing the T-handle all the way in. 1 A00053 45shampooed Elbow, .25MPcarpets X .25 FP usually have a heavy build-up of old shampoo residue which can cause 1 24Previously 5.25 G03523-1 Valve, Regulator, 200 PSI 1 vacuum system.25MP to ingest foam and result in damage to the vacuum motor. Remember to add recom26the A00052 90 Elbow, X .25FP 3 Hose Asm, 13 to in X .25HP 1 27 00580-13in-MF-A amount of defoamer the recovery tank every time you fill the solution tank. 28mended G00516-3 Gauge, 0-600PSI 1 6.29If aC11244 Powermate to be used Washer,is.56 X 1.5 X .05with the machine, connect the male plug on the wand to the optional 4 30 A00104 QD, 1-4 M X 1-4 FP, Brass 1 on.25 theFP, machine. A00161 Tee, Brass 1 31receptacle 32 A00111 Nipple, .25 in 2 33 C00232 Washer, .5 in, Flat 1 Additional Instructions forNPT GALAXY’s 34 A00154 90 Elbow, .25 X .25 NPT with HEAT’N’RUN installed: 1 35 C11440 Spacer, Heater Mounting Plate 4 Plug, 1.25solution in, Black tank with water before plugging in the machine. 1 1.36BeK10510 sure to fill the 4 37 C02322 Hex Bolt,1-4 X 20 X 1.75 in 2.38Water hookups be in Plate place and water flowing through the heater prior to turning it on. Failure to1do D010379 Heatermust Mounting Screw, #8 X 1 in, Pan, Blackdamage and will void the warranty. 5 39soC11165, may cause internal component 40 F11790 Heater, Tunnel Cover, Blue Granite 1 3.41Spray water theYellow tool / wand before turning on the heater to assure that there is water flow. 2 B11779 Stub,through 12-3 SJTW B00191 Nylon 11inwith Black 4 4.42Heater must beTie, filled water or water based solutions at all times when in use. 43 C00293 #8 X .5in Pan, Black SMS, Phillips 2 5.44Plug heater powerwith cordGlue and machine power cord into separate outlets on separate circuits. B00192 Tie Holder 1 B11606 Strain Relief, Pigtail 2 6.45Turn off the switch and unplug the heater from outlet when not in use. 46 H03545 Cover, Serial # Label 1 7.47DoH00565-5 not useLabel, heaterSerial withNumber any other machine than this adjustable PSI Galaxy. 1 48Turn C02305 Cap Nut, .5in Push-on 2 8.49 on heater switch when you are ready to clean. C00240 Washer, Shoulder, Nylon 4 50 G11767 Wheel, 10 in 2 51 D11170 Axle the green light on the heater is on, the heater is heating. When the green light is off, the 1 CAUTION: When 52 F11789 Base 1 53 C00314-1 Hex Bolt, 20to X 1in 8 water in the heater tank1-4 is Xup temperature and the thermostat switch in the heater has turned the heater 54 G03518 Caster, 4 in 2 off. will automatically turn120 onVagain when the water temperature in the heater has cooled. 55It G13102 Pump, 500 PSI, 1 56 B00177 Terminal Lug, Female, QD, .25 X .032, 16-14 AWG, Fully Insulated 2 57 C03251 Washer, .187 ID, Backup 1 DELIVER MAXIMUM HEAT by Fperforming the following SYSTEM WARM-UP PROCEDURES at the start 58 A00168 Bushing .375 M X .25 Brass 4 of each day: .50 Barb X .25 MP, Brass 59 A90004 1 60 A00155 Male Plug, .25 in, Nylon 1 J11933 .5 in Polywire 33 in lg 1 1.61Attach theHose, solution hose to PVC, the quick disconnect on the machine. 62 J00632 Pulse Hose, Pump - QD, 42 in 2 2.63Attach theNylon warm-up quick disconnect with spray tip attached to the other end of the solution hose. 13 B00190 Tie, 4in D13103 Plate, quick Pump,disconnect Galaxy, Flat in the solution tank. 1 3.64Place warm-up 65 H02564-2 Label, Caution, Motor Housing 1 4.66 FillJ11933 solution tank with cleaning solution. Hose, .5 in Polywire, 30 in 1 5.67Turn on pump. K11935 Strainer, Inline, .5 in 1 J11154 Solution Hose, out .375,of100PSI, Wire, 27 in lg disconnect, turn on the heater. 1 6.68When water is flowing the warm-up quick 69 J00618 Vacuum Hose, 2 in Grey, Wire, 7 in lg 1 7.70LetE11169 the pump andVac heater runGalaxy for 4 to 5 minutes. Gasket, Motor, 2 71 B00179-2 Closed End Cntr, 16-3 6 8. Remove warm-up quick disconnect. Attach the wand or upholstery tool and begin cleaning. Additional instructions: Prime the pump by connecting the pump priming hose, which is the 4 foot long solution hose with a stopper on one end, and a quick disconnect on the other end. Attach the quick disconnect to the machine, and the stopper to the vacuum hose. Make sure your solution tank is full of solution to create additional pressure. Turn on the pump, then the vacuum motors to create suction and draw water through the air locked pump. When the solution steadily flows through the solution line, your pump is primed. The pump should rarely ever need to be primed. If the solution tank is allowed to run low, it will result in the pump sucking in air, then the pump will need to be primed. Erratic pressure fluctuation indicates air in the lines and means the pump needs priming as well. OPERATING INSTRUCTIONS- CARPET TOOL 1. Turn on the vacuum and solution switches. Slowly pull the tool towards you with the solution valve trigger engaged. Then make a pass forward and backward with the vacuum only (no spray) over the cleaned area to remove as much dirt and solution as possible. Do not overwet carpet! Make overlapping passes to prevent streaking. 2. If the carpet is heavily soiled, squeeze solution valve on the forward pass as well as backwards, allowing cleaning solution a few seconds longer to work prior to vacuuming. Another method is to raise the wand 8” above the carpet and pre-spray lightly prior to cleaning passes. On extremely soiled carpets, we recommend using a pre-spray solution. 3. When you run out of solution, turn off the pump. Attach the drain elbow on the drain valve. Place a pail under the downspout and pull up the drain valve T-handle. Dirty solution will pour out until the tank is empty. Close the drain valve. Use a clean bucket when you refill the solution tank. 4. When the job is completed, turn the switch off and disconnect the vacuum and solution hoses from the carpet and the machine. Drain the recovery tank through the drain valve as before. POWERMATE 1204ACH 2000FX-HR Upper 1. Connect the cord on the power wand to the 1-26-08 optional receptacle in back of the machine. IMPORTANT: 1204ACH is for use with all heated Galaxy extractors. Turn on the vacuum and pump switches. ITEM PART NUMBER 2. NO. The motor for the power brush is turned on and off by a lighted rocker switch DESCRIPTION located on Solution the top Tank of the base. Solution application is controlled by squeezing 1 F11787 2 F11792 Recovery Tank the solution valve lever. 3 F11791 Lid, Solution Tank 3. To move the power wand forwards, push the wand handle downward, raise 4 A00060 3-8 Barb X 1-4MP, Brass the end push theXwand 5 front A00052 90 and Elbow, .25MP .25FP into position using the rear wheels. To pre6 C11244 Washer, .56 X valve 1.5 X .05 spray, squeeze solution lever while moving wand forward and backwards 7 00580-16.5 in-PH-A Hose Asm, 16.5 in X .25 in over the area to beRecovery pre-sprayed. 8 E11124 Gasket, Tank 4. To liftStand the wand handle to insure the nose of the wand is against the 12904A Pipe Assembly 9 clean, carpet, thenElbow, while 180 squeezing theBall solution valve lever, pull the wand towards Deg. Float 9A K11965 9B K00672 Pvc Pipe, 1.5 X 12 in, Sch 40 Wht you. Adapter 9C K00741 Here’s how it works- the solution is jet sprayed deep into the carpet 9D 10989-2A Float Ball Screen to loosen the dirt. The brush scrubs the fiber and breaks up surface 10 F11785 Lid, Recovery Tank deep1-4 dirt. 11 C12039and Washer, X 1,ItSSfluffs the nap without distortion to the pile. With the 12 C02322weight 1-4 X 20ofBolt the base on the suction head, the vacuum picks up the dirt 13 B11769 and Extension Cord, 12-3 SJTW solution. Make overlapping passes to prevent streaking. 14 C11177 Velcro Strap 5. Go over the path you just cleaner 15 H02548-2 Label, Important, Cord without squeezing the solution valve lever to remove as much Wires, dirt and solution as possible. 73 in 16 B00185-30 QTY. 1 1 1 2 3 3 1 1 1 1 1 1 1 1 2 2 2 2 2 2 17 B00185-40 Wires, 73 in 2 18 B010314 Wire Harness 1 POWERMATE 1800AC-200 19 F11786 Handle 1 4 20 B00177 Terminal Lug, Female, QD, .25 X .032, 16-14 AWG, Fully Insulated 1800AC-200 is for use with10allin heated Galaxy extractors. IMPORTANT: 21 B00185-40 Wire,14 GA Black, UL1015, 1 2 22 C00295-1 #10 X .75in Pan, Black SMS, Phillips 23 C00293 #8 X .5in Pan, Black SMS, Phillips 2 24 D11168 1 1. Connect theCover, cord Switchplate on the power wand to the optional receptacle in the back of the machine. Turn on the 25 B02211-1 Switch, Rocker, Green Light 3 vacuum and pump switches. 1 26 D010284 Switchplate 2. The motor of the rotating power brush is operated with your right hand controlling a long toggle switch. 27 E010453 Gasket, Switchplate 1 Pull it up for momentary use, push it down for continuous brush action (center off). Solution application is 28 B00177-1 Terminal Lug, Female, QD, .25 X .032 2 controlled by depressing the flow switch with your right hand fingertips. 29 B00185-30 Wire,14 GA White, UL1015, 10 lever in 1 30 adjust C02315 Lockwasher, #10 Int. Str, SSposition, pull up the grip on the locking lever located near the base 2 of 3. To the handle into operating 31 C00264 Nut, 10-32 1 the handle. Move the handle to waist level height and push down grip handle on lever to lock into place. 8 32 C11141 Screw, Allen Head, 10-24 X 1.25 in 4. To the Hose power wand forward, push handle downward to raise the front end and move the wand into 33 move K00665-1 Adapter, 1.5in, Black 1 position. ToGasket, pre-spray, 34 E11128 Draindepress Valve the flow switch lever (solution control) while 2 35 C00313 Hex Bolt, 1-4 X 20 X .5 SS 6 moving wand forwards or backward over the area to be cleaned with the front 36 C00233 Washer, Flat, .25 in 8 end raised. Lockwasher, .25 in., Internal Star 37 C02312 2 38 clean, D010283 Plate, Heater Mounting 1 5. To depress the solution flow lever while pulling the power wand towards you. 39 F11804 Here’s Heater how Mount 1 it works- the solution is jet sprayed deep into the carpet 40 C00261 Nut, .25-20, Hex 2 loosen dirt. The rotating brush scrubs the fiber and breaks up surface 41 K00710to Elbow, Drain Valve, Black 1 rooted 42 K00711and Draindeep Valve, Black dirt. It fluffs the nap without any distortion to the pile 1 43 C00254With Lockthe Washer, 1-4in 2 weight of Split the base on the suction head, the vacuum picks up 44 C02294the Screw, 1-4 20 X 1.25 2 dirt and solution. Make overlapping passes to prevent streaking. 45 K11185 Elbow, 90, 1.5 in, MT-MS, PVC 1 6. Make a passPvc over the1.5 path youin, just 46 K00672-1 Pipe, X 2.25 Schcleaned 40 Wht without depressing the solution flow 1 lever (vacuum only) and with the brush 47 E11129 Gasket, 5 ft. Long 1 48 A90004 .50 Barb X .25 MP, Brass 1 still on to remove as much dirt and solution 49 D00373 Inlet Filter, .25 NPT 2 as possible. 50 A00124 Hex Nut, .25 NPT Brass 2 51 C11143 Screw, 1-4 20 X 1.5 in, SS Pan Head, Phillips 2 52 S11179 Non-Skid Tape, 1 in. Roll 1 CLEANING UPHOLSTERY Cleaning upholstery with success requires a good knowledge of the type of fabric you will work on. Look for the cleaning instructions label sewn on the underside of the furniture for the recommended method of cleaning. If it calls for dry cleaning, do not attempt to clean by wet extraction otherwise damage to the fabric could occur. Extraction works perfectly on most synthetic fabrics including synthetic velvets. Before proceeding, test the fabric for colourfastness. Apply a small amount of cleaning solution on the fabric in an inconspicuous spot. Wait 2 to 3 minutes and rub the area with a white terry cloth towel. If no color comes off the towel, the fabric should be safe to clean. If a little color comes off, there is some risk of colors running when you clean. It may be possible to stabilize colors by cleaning with an acidic rinse. 1. Prepare the machine in the same manner as for carpet cleaning (see Preparing the Machine) except attach the upholstery tool to the vacuum hose. Connect the solution hose. Pour hot water into the solution tank. Add recommended amount of cleaning concentrate into the solution tank. Turn on the vacuum and pump switches. 2. Adjust the pump “operating pressure” to 50 PSI for upholstery cleaning (See Preparing the Machine). 3. Clean with the upholstery tool using as little solution as possible. Make overlapping passes to prevent streaking. Go over the area you just cleaned without depressing the lever (vacuum only) and gauge the amount of moisture extracted through the view window for dryness. On heavily soiled areas like arm rests, pre-treat with a recommended pre-spray solution or hold the upholstery tool a few inches above the fabric and press lever to spray on the solution before making a pass. DAILY MAINTENANCE 1. Always keep the machine clean inside and out. 2. Pour 2 gallons of clean hot water in the solution tank. Turn on and flush the entire system through the wand nozzles for about a minute to prevent build-up. 3. Remove dirt and lint build-up inside the filter screen in the recover tank. Lint should be cleaned off so that air flow is not impeded. 4. Check the solution tank strainer in the solution tank. If lint has accumulated in the screen, remove and rinse it in clear running water. PERIODIC MAINTENANCE All EDIC machines are engineered and built to require a minimum of maintenance. But like any machine, it does require some care to keep it in optimum working condition. Careful attention to these maintenance instructions will give you maximum operating performance and will increase the life expectancy of your machine. • • • • Solution Lines and Fittings: Flush the machine at least once a month with a solution of 3 parts water with 1 part white vinegar in order to neutralize the alkaline residue left by the cleaning solution. Quick Connect Coupler: Spray with WD-40 or equivalent lubricant to prevent coupler from sticking. Drain Valve: Apply light oil on gate seals. If machine has to be stored, leave the gate valve open. Solution Pump: The same above procedure used on the solution line and fittings applies to the pump. 2000WX-HR & KX-HR Base 200 PSI 4-1-08 TROUBLESHOOTING ITEM NO. 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60 61 62 63 64 Electrical System WX PART NUMBER KX PART NUMBER PROBLEM CAUSE PROBLEM C00297 #8 X .25 Pan Head J11863 Hose, 3 in No electrical power. J00639 Screw Clamp, 1.63 - 2.43in. 1. Defective power cord. 2. 22 House J00618 Vacuum Hose, 2in Grey, Wire, in lg or building circuit breaker tripped. F11178-BLK Intercooler, Galaxy, Black Switch is turned C00273 Locknut, 1-4 Xon. 20, Nylon, SS 1. Faulty electrical cable. PowerWasher, is intermittent to 2. Defective switches. C00233 Flat, .25 in E00449 Grommet all motor(s) 3. Loose terminal or discolored terminal connections. C00284 Screw, 10-32 X .375 Ground B11150 GroundSystem Wire, Galaxy Vacuum G00520-1L Vacuum , 135 in, 115 V, 5.7 in G02517-1 Vacuum, 117 in., 115 V, 5.7 in 1. Drain valve open. J00657 Hose Clamp, 2 inSLDPRT J00618 Vacuum Hose, 2 in Grey, Wire, 4 in lg No Vacuum 2. Vacuum lid is not sealed against tank. C00261 Nut, .25-20, Hex 3. Loose vacuum hose, vacuum connection. C00254 Lock Washer, 1-4in Split Low Vacuum 1. Accumulated dirt on lid screen. D11134 Vac Plate C11189 Screw, 1-4 X 20 X 4.5 in, Hex2. Worn out vacuum lid gasket. C02312 Lockwasher, .25 in., Internal Star C11516 Screw, 1-4 X 20 X 4.5 in, Flat 3.Head, Lint &Phillips dirt build-up on wand head. A00111 Nipple, .25 in 4. Defective vacuum hose. A00052 90 Elbow, .25MP X .25FP 5. Loose connection in one of the vacuum motors. A00161 Tee, .25 FP, Brass A00121 Fitting, .25 MP X .25 FP, Brass Solution System C11244 Washer, .56 X 1.5 X .05 Pump motor noFP, Brass 1. Clogged spray tips. A00104 QD, 1-4 Mon, X 1-4 A00154 Elbow, .25 tips NPT X .25 NPT 2. Clogged solution intake filter screen. spray90thru spray C11560 Washer, .93 ID X 1.5 OD 3. Plugged female quick disconnect coupler. 00580-13in-MF-A Hose Asm, 13 in X .25HP G13133 Valve, Regulator, 200 PSI 4. Punctured pump diaphragm. G00516-3 Gauge, 0-600PSI 5. Defective pump check valve. C11440 Spacer, Heater Mounting Plate 6. Crack in pump housing. K10510 Plug, 1.25 in, Black C02322 Hex Bolt,1-4 X 20 X 1.75 in 7. Debris in check valve. D010379 Heater Mounting Plate 8. Lost Prime. C11165, Screw, #8 X 1 in, Pan, Black F11790 Heater, Tunnelspray Cover, Blue Granite Uneven or weak 1. Clogged or dirty spray tips. B11779 Stub, 12-3 SJTW Yellow fromNylon tips. Tie, 11in Black 2. Accumulated dirt on solution intake filter screen. B00191 C00293 #8 X .5in Pan, Black SMS, Phillips 3. Accumulation of debris inside pump and plumbing. B00192 Tie Holder with Glue 4. Worn pump bearing (excessive noise). B11606 Strain Relief, Pigtail 5. Punctured pump diaphragm. H03545 Cover, Serial # Label H00565-5 Label, Serial Number 6. Defective rectifier or motor. C02305 Cap Nut, .5in Push-on 7. Worn nozzles. C00240 Washer, Shoulder, Nylon 8. Pressure regulator set incorrectly. G11767 Wheel, 10 in D11170 Axle Vacuum 1. Loose wiring connection. F11789 Base motor (s) C00314-1 Hexpump Bolt, 1-4 X 20 X 1in working, motor 2. Defective pressure switch in pump. G03518 Caster, 4 in fails toPulse turnHose, on Pump - QD, 423. J00632-1 in Defective pump motor or rectifier. A13140 Cap, FPT, .375 Brass Erratic Pressure 1. Pump check valves defective or dirty. G13132 Pump, 200 PSI, 120 V 2. Lost prime. B00190 Nylon Tie, 4in J11508 Screw Clamp #6, .43 to .875 in D13103 Plate, Pump, Galaxy, Flat OPTIONAL ACCESSORIES H02564-2 Label, Caution, Motor Housing J11933 Hose, .5 in Polywire, 20 in HEAT-N-RUN K11935 Strainer, Inline, .5 in J11933 Hose, .5 in Polywire, 33 in J11154 Solution Hose, .375, 100PSI, Wire, 27 in lg J00618 Vacuum Hose, 2 in Grey, Wire, 7 in lg E11169 Gasket, Vac Motor, Galaxy B00179-2 Closed End Cntr, 16-3 QTY. 1 1 3 1 1 16 26 6 2 2 2 1 1 10 1 1 5 1 1 1 4 1 1 5 1 3 1 1 1 1 4 1 4 1 4 1 1 4 2 1 1 1 1 2 4 2 1 1 8 2 2 1 1 13 6 1 1 1 1 1 1 1 2 4 NOTES _________________________________ _________________________________ _________________________________ _________________________________ _________________________________ _________________________________ _________________________________ _________________________________ _________________________________ _________________________________ _________________________________ _________________________________ _________________________________ _________________________________ _________________________________ _________________________________ _________________________________ _________________________________ _________________________________ _________________________________ _________________________________ _________________________________ _________________________________ 11 12 13 14 15 16 17 18 19 20 21 22 10 23 9 24 25 8 26 7 27 6 5 5A 5C 3 5B 28 30 5D 4 2 1 31 38 53 37 36 29 32 33 34 35 39 52 40 41 42 43 51 44 50 45 49 48 47 46 Upper 3-25-08 17 GALLON GALAXY 200 PSI (UPPER) PARTS LIST ITEM # 1 2 3 4 5 A B C D 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 PART # F11787-BLANK F11788-1 F11791-1 G11836 12904A K11965 K00672 10989-2A K00741 F11785-1 C11167 K02714 B11769 C11177 H02548-2 B00185-30 B00185-40 B010314 F11786-1 B00177 B00185-40 C00295-1 C00293 D11168 B02211-1 D010284 E010453 B00177-1 B00185-30 C02315 C00264 C00288-1 C00288 K00666 K00665-1 C00313 C02312 C00314-1 C00233 D010283 F11804 C00261 K00710 K00711 E11128 C12110 C11540 K11185 K00672-1 A00060 A00052 C11244 A00124 D00373 C11144 S11179 C00238 DESCRIPTION SOLUTION TANK, GALAXY PRO RECOVERY TANK, GALAXY PRO LID, SOLUTION TANK, GALAXY PRO GASKET, RECOVERY TANK STAND PIPE ASSY ELBOW, 180 DEG. FLOAT BALL PVC PIPE, 1.5 X 12 IN, SCH 40 WHT FLOAT BALL SCREEN ADAPTER LID, RECOVERY TANK BOLT, 1-4 X 20 PLUG, .500 EXTENSION CORD, 12-3 SJTW VELCRO STRAP LABEL, IMPORTANT, CORD WIRES, 73 IN WIRES, 73 IN WIRE HARNESS HANDLE TERMINAL LUG, FEMALE, QD , .25 X .032, 16-14 AWG FULLY INSULATED WIRE, 14 GA BLACK, UL1015, 15IN #10 X .75INPAN, BLACK SMS, PHILLIPS #8 X .5IN PAN, BLACK SMS, PHILLIPS COVER, SWITCHPLATE, GALAXY SWITCH, ROCKER, GREEN LIGHT SWITCHPLATE GASKET, SWITCH BRACKET TERMINAL LUG, FEMALE, QD, .25 X .032 WIRE, 14 GA WHITE, UL1015, 5IN LOCKWASHER, #10 INT. STR,SS NUT, 10-31 .25-20 X 2.25 FLAT HEAD .25-20 X 1.5 FLAT HEAD 90 ELBOW, SCH D 40, 1.5 IN HOSE ADAPTER, 1.5 IN, BLACK HEX BOLT, .25 X 20 X .75 LOCKWASHER, .25 IN, INTERNAL STAR HEX BOLT, 1-4 X 20 X 1 IN WASHER, FLAT, .25 IN PLATE, HEATER MOUNTING HEATER MOUNT NUT, .25-20, HEX ELBOW, DRAIN VALVE, BLACK DRAIN VALVE, BLACK GASKET, DRAIN VALVE HEX BOLT, .375-16 X 1.75 WASHER, .375 ID X .875 OD ELBOW, 90, 1.5IN, MT-MS, PVC PVC PIPE, 1.5 X 2.25 IN, SCH 40 WHT 3-8 BARB X 1-4MP, BRASS .25 X .375 M-F DEG BRASS WASHER, .56 X 1.5 X .05 HEX NUT, .25 NPT, BRASS INLET FILTER, .25 NPT SCREW, .25-20 X 2, SS NON-SKID TAPE, 1 IN ROLL WASHER, .275 IN, NEOSTEEL QTY 1 1 1 1 1 1 1 1 1 1 6 4 1 1 1 1 1 1 1 2 1 2 2 1 3 1 1 4 1 2 1 4 4 1 1 2 2 4 6 1 1 2 1 1 1 2 2 1 1 1 1 1 1 1 2 1 2 2 1 3 4 5 6 7 8 9 10 66 11 65 12 13 14 15 64 16 63 62 7 20 21 22 23 24 25 26 27 6 61 54 6 56 57 58 59 19 18 60 28 22 29 30 31 17 35 34 7 33 32 15 55 55 36 41 40 39 38 37 42 54 43 53 44 52 46 51 50 7 49 48 47 BASE 2-3-08 46 45 17 GALLON GALAXY 200 PSI (BASE) PARTS LIST ITEM # 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60 61 62 63 64 65 66 PART # C00297 J11863 J00639 J00618 F11178-BLK C00273 C00233 E00449 C00284 B11150 G00537 J00657 J00618 C00254 C00261 D11134 C11189 C11516 C02312 G11314-2 A00060 A00052 A00161 A00111 A00121 C11244 A00104 A00097A A00094E A00094C C02291 D010379 K10691 A00061 H02564-2 C11165 F11790 B11779 C00293 B00192 B11606 K10510 H03545 H00565-5 C02305 C00240 G11767 D11170 F11789 C02310 G03518 J00613B J11508 A00054 B00191 B00190 G13132 D11835M-1 J00613B J11154 A11243 J11154 J00618 E11169 B00179-2 B00179-1 DESCRIPTION SCREW, #8 X .25IN, PAN HEAD HOSE, 3IN SCREW CLAMP, 1.63-2.43IN VACUUM HOSE, 2 IN GREY, WIRE22 IN LG INTERCOOLER, GALAXY, BLACK LOCKNUT, 1-4 X 20, NYLON, SS WASHER, FLAT, .25 IN GROMMET SCREW, 10-32 X .375 GROUND GROUND WIRE, GALAXY VACUUM, 82 IN, 115 V, 5.7 IN HOSE CLAMP, 2 IN SLDPRT VACUUM HOSE, 2 IN GREY, WIRE, 4 IN LG LOCK WASHER, 1-4 IN SPLIT NUT, .25-20, HEX VAC PLATE SCREW, 1-4 X 20 X 4.5IN, HEX SCREW, 1-4 X 20 X 4.5IN, FLAT HEAD, PHILLIPS LOCKWASHER, .25 IN, INTERNAL STAR PRESSURE REGULATOR, 180 PSI 3-8 BARB X 1-4 MP, BRASS .25 X .375 M-F 90 DEG, BRASS TEE, .25 FP, BRASS NIPPLE, .25 IN FITTING, .25 MP X .25 FP, BRASS WASHER, .56 X 1.5 X .05 QD, 1-4M X 1-4FP, BRASS CAP, INLINE FILTER CHECKVALVE, NO STRAINER CHECK VALVE BODY HEATER PLATE HEX HEATER MOUNTING PLATE PVC PIPE, .25IN 3-8 BARB X 1-4RP, BRASS LABEL, CAUTION, MOTOR HOUSING SCREW, #8 X 1 IN, PAN, BLACK HEATER, TUNNEL COVER, BLUE GRANITE STUB, 12-3 SJTW, YELLOW #8 X .5 IN PAN, BLACK SMS, PHILLIPS MOUNT, NYLON TIE STRAIN RELIEF, PIGTAIL PLUG, 1.25 IN, BLACK COVER, SERIAL # LABEL LABEL, SERIAL NUMBER CAP NUT, .5 IN PUSH- ON WASHER, SHOULDER, NYLON WHEEL, 10 IN AXLE BASE HEX BOLT, 1/4 X 20 X 1 1/4" CASTER, 4 IN SOLUTION HOSE, .375 IN, BLACK SCREW CLAMP #6, .43 TO .875 IN ELBOW, 90, .375 MP X .375B, NYLON NYLON TIE, 11 IN BLACK NYLON TIE, 4 IN PUMP, ADJUSTABLE PRESSURE 50 - 200 PSI PUMP PLATE SOLUTION HOSE, .375 X 26 IN, BLACK SOLUTION HOSE, .375 X 10 IN, WIRE REINFORCED TEE, .375B X .375B X .375B, NYLON SOLUTION HOSE, .375 X 6 IN, WIRE REINFORCED VACUUM HOSE, 2 IN GREY, WIRE, 7 IN LG GASKET, VAC MOTOR, GALAXY CLOSED END CNTR, 16-3 CLOSED END CNTR, 16-3 QTY 1 1 3 1 1 16 26 6 2 2 1 1 1 1 10 1 5 1 1 1 1 3 1 2 1 2 1 1 1 1 4 1 4 1 1 4 1 1 2 1 1 1 1 1 2 2 2 1 1 8 2 1 8 2 4 13 1 1 1 1 1 1 1 2 1 3 ">

Public link updated
The public link to your chat has been updated.
Advertisement